advertisement
IR Indoor Mini Dome Network Camera
User Manual Precautions
Precautions
Precautions
Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip "You have entered the area of electronic surveillance" in an eyecatching place. Failure to correctly use electrical products may cause fire and severe injuries. To prevent accidents, carefully read the following context:
Symbols
This document may contain the following symbols whose meanings are described accordingly.
Symbol Description
It alerts you to fatal dangers which, if not avoided, may cause deaths or severe injuries.
It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries.
It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results.
It provides a tip that may help you resolve problems or save time.
It provides additional information.
To prevent electric shocks or other dangers, keep power plugs dry and clean.
Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users' nonconformance to these requirements. i
IR Indoor Mini Dome Network Camera
User Manual
Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
Precautions
Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
When this device is in use, ensure that no water or any liquid flows into the device.
If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
Do not focus strong light (such as lighted bulbs or sunlight) on this device.
Otherwise, the service life of the image sensor may be shortened.
If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.
Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring.
Remove the power plug if the device is idle for a long time.
Before unpacking, check whether the fragile sticker is damaged. If the fragile sticker is damaged, contact customer services or sales personnel. The manufacturer shall not be held responsible for any artificial damage of the fragile sticker. ii
IR Indoor Mini Dome Network Camera
User Manual Precautions
Special Announcement
All complete products sold by the manufacturer are delivered along with nameplates, operation instructions, and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product. The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.
iii
IR Indoor Mini Dome Network Camera
User Manual Contents
Contents
4.2.2 Watch real-time video in Chrome, Firefox, or Safari browsers ........................ 12
iv
IR Indoor Mini Dome Network Camera
User Manual
1
Overview
1
Overview
1.1 Hardware Connection
Figure 1-1 shows the multi-connector combination lines of the IR Indoor Mini Dome
Network Camera and Table 1-1 describes the multi-connector combination lines.
Figure 1-1 Hardware connection
Table 1-1 Multi-connector combination lines
ID Type Function Description
1
2
3
RJ45
Barrel Jack Power Supply port Connects to a DC12V power supply
RCA audio interface
Network connection Connects a standard ethernet cable
Audio input Linear input. When microphone input is used, a head amplifier is needed.
4 Audio output Linear output. When speaker output is used, an amplifier is used.
1
IR Indoor Mini Dome Network Camera
User Manual
Figure 1-2 Internal structure of IR mini dome network camera
1
Overview
Table 1-2 Descriptions of hardware interfaces
Component
Video
(Video output)
Power
(Power supply)
Network (Network connection indicator)
SD
(SD card indicator)
Description
Outputs analog video signal and connects a TV monitor to watch analog videos.
POE can be used to supply power or external DC12
V power supply can be connected.
Flashes when the network is connected.
The status of the SD indicator :
OFF : SD card is not inserted.
ON : SD card is inserted.
Press the key for 5s to restore factory settings. Reset To Default
(Reset key)
Net Activity
(Network activity indicator)
SD card slot
When there is a network activity, the indicator flashes.
Connects an SD card.
Note:
When installing an SD card, make sure that the SD card is not in the write protection status and then insert the SD card into the card slot.
2
IR Indoor Mini Dome Network Camera
User Manual
Component
1
Overview
Description
When removing an SD card, make sure that the SD card is not in the read/write status. Otherwise, data may be lost or the SD card may be damaged.
When hot plugging an SD card, stop recording first.
1.2 Features
Network Features
Supports complete TCP/IP protocol suite.
Supports video, audio streaming.
Provides a built-in web browser and supports access using Internet explorer..
Supports network data transmission and remote access.
Supports Point-to-Point protocol over Ethernet (PPPoE), Dynamic Host configuration protocol (DHCP), and Dynamic Domain Name System (DDNS) protocols.
Supports remote upgrade and maintenance.
Image Processing Features
Supports multiple steams. Single-stream mode or dual-stream mode can be selected based on the site requirement. Encoding parameters for the main stream and sub stream be configured separately.
Supports dynamic stream parameters based on different image quality requirement.
Supports independent hardware compression and constant bit rate (CBR) and variable bit rate(VBR) Videos can be compressed using the Motion Joint
Photographic Experts Group (MJPEG) , H.264 or HP standard. The frame rate and image quality can be configured
I/O Features
Support bidirectional intercom and unidirectional broadcast.
Provides a 10/100 Mbit/s self-adaptive Ethernet port.
Other Features
Supports the heartbeat function that allows the management host to learn the running status of the IP camera in real time.
Supports motion detection alarm, and alarm linkage function.
Supports level-based user rights management.
3
IR Indoor Mini Dome Network Camera
User Manual
2
Device Dimensions
Figure 2-1 shows the camera dimensions.
Figure 2-1 Dimensions (unit: mm)
2
Device Dimensions
4
IR Indoor Mini Dome Network Camera
User Manual
3
Device Installation
3
Device Installation
3.1 Preparations
You may need the tools and accessories shown in Table 3-1 during the installation (you
need to prepare the tools by yourself, and the accessories are in the package of the camera).
Table 3-1 Installation tools
Tools
Phillips screwdriver (prepare by yourself)
Appearance
Claw hammer (prepare by yourself)
Hammer drill (prepare by yourself)
Spirit level (prepare by yourself)
T15 ring spanner (delivered with the camera)
Self-tapping screw (delivered with the camera)
Inflatable colloidal particle (delivered with the camera)
5
IR Indoor Mini Dome Network Camera
User Manual
3
Device Installation
To avoid the impact of humidity, after installing the device, power on the device for at least half an hour before sealing the cover.
3.2 Installation Mode
The IR Indoor Mini Dome Network Camera can be installed in ceiling mounting or side wall mounting mode. In general, it is used in an indoor or building environment,
but can also be used in an outdoor environment. Figure 3-1 shows the ceiling mounting
mode. The side wall mounting mode is similar to the ceiling mounting mode.
NOTE
To achieve a good angle of view, you are advised to install the device in the place whose vertical distance from the ground is about 3 m to 6 m.
Figure 3-1 Ceiling mounting mode
The ceiling mounting procedure is as follows:
Step 1 Unfasten the two torx screws on the cover of the mini dome by using the T15 combination wrench in the accessory package and open the cover upward, as shown in
Open the cover gently and pull out the MIC line from the MIC socket, be careful not to snap the MIC line.
6
IR Indoor Mini Dome Network Camera
User Manual
Figure 3-2 Opening the cover
3
Device Installation
Step 2 Take out the installation positioning sticker in the package box, remove the release paper on the back of the sticker, and paste the sticker on the required installation position on the top.
First, determine the required installation direction of the camera. If top cable outlet is used, drill through holes whose diameter is about 25 mm in the places that are about 15 mm away from the characters “CABLE OUT" on the sticker.
Step 3 After pasting the installation positioning sticker, align the drill bit whose diameter is
5.5 mm with the two round holes marked with “DRILL HOLE” on the sticker and drill two holes that are 35 mm deep.
Step 4 Take out the two white plastic particles in the accessory package, knock the white plastic particles into the drilled two holes by using a hammer, and observe whether the ceiling is flat. The white plastic particles cannot stand out.
Step 5 Take the camera whose cover is removed in Step 1, align the two installation holes at the bottom of the camera with the two white plastic particles, take out two black selftapping screws in the accessory package, and install the camera on the ceiling by using
an electric Phillips screwdriver, as shown in Figure 3-3.
7
IR Indoor Mini Dome Network Camera
User Manual
Figure 3-3 Installing the camera on the ceiling
3
Device Installation
Step 6 Connect the RJ45 network conversion adapter in the accessory package to the power wiring terminal.
In this step, you can perform operations such as inserting or removing the SD card, resetting a function, and adjusting a video.
Unfasten the screws on both sides of the lens by using a Phillips screwdriver until you can turn the lens dome manually, observe the angle of view through the second video interface, adjust the angle of the lens dome until a satisfactory effect is achieved, and then fasten the two screws on both sides of the lens again by using a Phillips
screwdriver, as shown in Figure 3-4.
8
IR Indoor Mini Dome Network Camera
User Manual
Figure 3-4 Adjusting the direction and angle of the camera
3
Device Installation
Step 7 Connect the MIC plug to the MIC socket at first, ensure that the plug is not loose, then install the cover by using the T15 combination wrench or an electric screwdriver with
T15 torx, as shown in Figure 3-5.
Figure 3-5 Installing the cover
9
IR Indoor Mini Dome Network Camera
User Manual
4
Quick Configuration
4
Quick Configuration
4.1 Login and Logout
You must use Internet Explorer 7 or a later version to access the web management system; otherwise, some functions may be unavailable.
Login system
Step 1 Open the Internet Explorer, enter the IP address of IP camera (default value:
192.168.0.120) in the address box, and press Enter. The login page is displayed.
Step 2 Input the User name and password.
The default name is admin. The default password is 1234. Change the password when you log in the system for first time to ensure system security.
You can change the system display language on the login page.
Step 3 Click Login.
The main page is displayed. logout
To logout of system, click Sign out in the upper right corner of the main page, the login page is display after you log out of the system.
4.2 Browsing Video
User can browse the real-time video in the web management system.
Preparation
To ensure the real-time video can be play properly, you must perform the following operation when you log in to the web for the first time:
1. Open Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites.
In the display dialog box, click Add, as shown in Figure 4-1.
10
IR Indoor Mini Dome Network Camera
User Manual
Figure 4-1 Adding the a trusted site
4
Quick Configuration
2. In the Internet Explorer, choose Tool > Internet Options > Security > Customer level
, and set Download unsigned ActiveX control and initialize and script
ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins
to Enable, as shown in Figure 4-2.
Figure 4-2 Configuring ActiveX control and plug-ins
3. Download and install the player control as prompted.
11
IR Indoor Mini Dome Network Camera
User Manual
4
Quick Configuration
The login page is display when the control is loaded.
4.2.1 Download control in the Internet Explorer
Real-time video page shows the message clicks to play live video with ActiveX control to reduce latency
.
Click the message, jump to download ActiveX control interface, once downloading is complete, you can watch more fluent video screen.
Unable to display video image, and need to download and install the control
Real-time video page shows the message click to download the latest version of
Flash Play live video
and click to play video with ActiveX control to reduce latency.
Click the message click to play live video with ActiveX control to reduce latency, jump download Adobe Flash Player Plugin control interface, once downloading is complete, you can watch video screen.
Click the message click to download the latest version of Flash Play live video, jump to download ActiveX control interface, once downloading is complete, you can watch more fluent video screen.
4.2.2 Watch real-time video in Chrome, Firefox, or Safari browsers
Google, Firefox, and Safari browsers only support Adobe Flash Player Plugin to play video. When Adobe Flash Plugin control version is too low, browser will automatically ask you to download the latest control.
4.3 Setting Local Network Parameters
Description
Local network parameters include:
IP protocol
IP address
Subnet mask
Default gateway
Dynamic Host Configuration Protocol (DHCP)
Preferred Domain Name System (DNS) server
Alternate DNS server
MTU
Procedure
Step 1 Choose Device > Local Network, the Local Network page is displayed.
Step 2
Set the parameters according to Table 4-1.
12
IR Indoor Mini Dome Network Camera
User Manual
Table 4-1 Local network parameters
Parameter
IP Protocol
Description
IPv4 is the IP protocol that uses an address length of 32 bits.
DHCP
(Obtain an IP address automatically)
IP Address
Subnet Mask
Default Gateway
Preferred DNS
Server
Alternate DNS
Server
MTU
The device automatically obtains the IP address from the
DHCP server.
Device IP address that can be set as required.
Subnet mask of the network adapter.
This parameter must be set if the client accesses the device through a gateway.
IP address of a DNS server.
IP address of a domain server.
If the preferred DNS server is faulty, the device uses the alternate DNS server to resolve domain names.
Set the maximum value of network transmission data packets.
4
Quick Configuration
Setting
[Setting method]
Select a value from the drop-down list box.
[Default value]
IPv4
[Setting method]
Click the button on to enable obtain IP address automatically
.
[Setting method]
Enter a value manually.
[Default value]
192.168.0.120
[Setting method]
Enter a value manually.
[Default value]
255.255.255.0
[Setting method]
Enter a value manually.
[Default value]
192.168.0.1
[Setting method]
Enter a value manually.
[Default value]
192.168.0.1
[Setting method]
Enter a value manually.
[Default value]
192.168.0.2
[Setting method]
Enter a value manually.
Note
The MTU value is range from 800 to 1500, the default value is 1380, please do not change it arbitrarily.
13
IR Indoor Mini Dome Network Camera
User Manual
4
Quick Configuration
Step 3 Click Apply.
If the message "Apply succeed!" is displayed, click Confirm. The system saves the settings. The message "Set network parameter success, Please login system again" is displayed. Use the new IP address to log in to the web management system.
If the message "Invalid IP Address", "Invalid Subnet Mask", "Invalid default gateway", "Invalid primary DNS", or "Invalid space DNS" is displayed, set the parameters correctly.
14
IR Indoor Mini Dome Network Camera
User Manual
5
Technical Specifications
5
Technical Specifications
Table 5-1 lists the technical specifications of the Camera.
Table 5-1 Technical specifications
Camera
Image Sensor
Max. Resolution
Scanning system
Min. Illumination
IR-LED
Lens
1/3” Progressive Scan CMOS
1920 x 1080
Progressive Scan
Color 0.2 Lux, IR On 0 Lux
1pcs / 6~7m
Focal Length
Angle of view
CNV-2M03RS : f = 2.8mm
CNV-2M04RS : f = 3.6mm
CNV-2M03RS : 107°
CNV-2M04RS :75°
Fixed Lens / Board Mount Lens / Mount type
Functions
Day & Night ICR
Gain Control
White Balance
Auto / Manual
Auto
WDR D-WDR
Digital Noise Reduction 2D/3D DNR
Motion Detection Off / On
Privacy Zone Masking Max. 4 Areas
Corridor Mode Off / On
Email Notification Event Notification
Network
Ethernet
Video Compression
Ethernet 10/100 Base-T(RJ-45)
H.264, High/ Main/ Baseline Profile, MJPEG
15
IR Indoor Mini Dome Network Camera
User Manual
Max. Frame rate
Bit rate Control
Bit Rate (CBR/VBR)
Audio Input / Output
Audio Compression
IP
Power Consumption
Mechanical
Color / Material
Dimension
Weight
5
Technical Specifications
30fps@1920x1080
CBR / VBR
Main stream : 500kb-12000kb
Sub stream : 100kb-6000kb
1ch Audio Input / 1ch Audio Output
G.711, RAW_PCM
Protocol
Security
Memory Slot
ONVIF
IPv4 / IPv6
HTTP, HTTPS, TCP/IP, UDP/IP, RTSP, DHCP, NTP,
PPPoE
Remote Access
Environmental
Web, PC, Mobile Viewer
Operation Temperature -20°C ~ +55°C
Operation Humidity 0% ~ 90% RH
IP Rating
Power
Input Power
User Verification, Communication Encryption
Micro SD/ SDHC, Up to 32GB
Onvif 2.4
IP65
DC12V, PoE
2.5W (IR-LED Off), 5W(IR-LED On)
White / Aluminum
100(Φ) x 53(H) mm
Approx. 650g
16
IR Indoor Mini Dome Network Camera
User Manual
A
Hazardous Substance Declaration
Hazardous Substance or Element
Component Plumbum
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr6+)
Polybrominated
Biphenyls (PBB)
Polybrominated
Diphenyl Ethers
(PBDE)
Structural part
Board/circuit module
Cable connector
Accessories
×
×
×
×
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○: indicates that the concentration of the hazardous substance in all homogeneous substances of the component is within the limit specified in SJ/T 11363-2006 Requirements for Concentration
Limits for Certain Hazardous Substances in Electronic Information Products
.
×: indicates that the concentration of the hazardous substance in at least one homogeneous substance of the component exceeds the limit specified in SJ/T 11363-2006 Requirements for Concentration
Limits for Certain Hazardous Substances in Electronic Information Products
.
101-100-0370-02
17
IR Indoor Mini Dome Network Camera
User Manual
18
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Indoor surveillance
- Infrared camera
- Motion detection
- Small and discreet
- Can be ceiling or wall mounted
Related manuals
Frequently Answers and Questions
Can this device be installed outdoors where it may face rain?
Can this device record footage?
Is the power adapter included with the device?
advertisement