INVR-0xA / INVR-0xPOE
Network Video Recorder
User Manual
v1.0
User Manual of INVR-0xA / INVR-0xPOE series NVR
Regulatory information
FCC information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the
applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal
waste in the European Union. See the product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
2
User Manual of INVR-0xA / INVR-0xPOE series NVR
Preventive and Cautionary Tips
Before connecting and operating your device, please be advised of the following tips:
•
•
•
•
•
Ensure unit is installed in a well-ventilated, dust-free environment.
Unit is designed for indoor use only.
Keep all liquids away from the device.
Ensure environmental conditions meet factory specifications.
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it
may cause damage to the sensitive electronics within the unit.
•
•
•
•
Use the device in conjunction with an UPS if possible.
Power down the unit before connecting and disconnecting accessories and peripherals.
A factory recommended HDD should be used for this device.
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
3
User Manual of INVR-0xA / INVR-0xPOE series NVR
Product Key Features
General


Connectable to network cameras, network dome and encoders.
Connectable to the third-party network cameras like AXIS, Brickcom, Bosch, PANASONIC,
SAMSUNG and SANYO, and network cameras that adopt ONVIF or PSIA protocol.

PAL/NTSC adaptive video inputs.

Each channel supports dual-stream.

Up to 8 network cameras can be connected.

Independent configuration for each channel, including resolution, frame rate, bit rate, image quality,
etc.

The quality of the input and output record is configurable.
Local Monitoring

Simultaneous HDMI and VGA outputs.

HDMI output and VGA output at up to 1920×1080 resolution.

Multiple screen display in live view is supported, and the display sequence of channels is adjustable.

Live view screen can be switched in group, and manual switch and automatic cycle live view are also
provided, and the interval of automatic cycle can be adjusted.

Quick setting menu is provided for live view.

Motion detection, video tampering, video exception alert and video loss alert functions.

Privacy mask.

Multiple PTZ protocols supported; PTZ preset, patrol and pattern.

Zooming in by clicking the mouse and PTZ tracing by dragging mouse.
HDD Management

Up to 2 SATA hard disks can be connected. (Each disk with a maximum of 4TB storage capacity.)

8 network disks (8 NAS disks, or 7 NAS disks+1 IP SAN disk) can be connected.

Support S.M.A.R.T. and bad sector detection.

HDD group management.

Support HDD standby function.

HDD property: redundancy, read-only, read/write (R/W).

HDD quota management; different capacity can be assigned to different channel.
Recording and Playback

Holiday recording schedule configuration.

Continuous and event video recording parameters.

Multiple recording types: manual, normal, motion

8 recording time periods with separated recording types.

Pre-record and post-record for motion detection for recording, and pre-record time for schedule and
manual recording.

Searching record files by events (motion detection).

Tag adding for record files, searching and playing back by tags.

Locking and unlocking record files.

Local redundant recording.

Searching and playing back record files by channel number, recording type, start time, end time, etc.

Smart search for the selected area in the video.

Zooming in when playback.

Reverse playback of multi-channel.

Supports pause, play reverse, speed up, speed down, skip forward, and skip backward when playback,
4
User Manual of INVR-0xA / INVR-0xPOE series NVR
and locating by dragging the mouse.

Up to 8-ch synchronous playback at 4CIF real time.
Backup

Export video data by USB or SATA device.

Export video clips when playback.

Management and maintenance of backup devices.
Alarm and Exception

Alarm for video loss, motion detection, tampering, abnormal signal, video input/output standard
mismatch, illegal login, network disconnected, IP confliction, abnormal record, HDD error, and HDD
full, etc.

Alarm triggers full screen monitoring, audio alarm, notifying surveillance center, sending email and
alarm output.

Automatic restore when system is abnormal.
Other Local Functions

Operable by mouse and remote control.

Three-level user management; admin user is allowed to create many operating accounts and define
their operating permission, which includes the limit to access any channel.

Operation, alarm, exceptions and log recording and searching.

Import and export of device configuration information.
Network Functions

1 self-adaptive 10M/100M/1000M network interface.

IPv6 is supported.

TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, and iSCSI are
supported.

TCP, UDP and RTP for unicast.

Auto/Manual port mapping by UPnP.

Remote web browser access by HTTPS ensures high security.

Remote reverse playback via RTSP.

Support accessing by the platform via ONVIF.

Remote search, playback, download, locking and unlocking of the record files, and support
downloading files broken transfer resume.

Remote parameters setup; remote import/export of device parameters.

Remote viewing of the device status, system logs and alarm status.

Remote locking and unlocking of mouse.

Remote HDD initializing and program upgrading.

Remote system restart and shutdown.

RS-485 transparent channel transmission.

Exception information can be sent to the remote host.

Remotely start/stop recording.

Remote PTZ control.

Two-way audio and voice broadcasting.

Embedded WEB server.
Development Scalability:

SDK for Windows and Linux system.

Source code of application software for demo.

Development support and training for application system.
5
User Manual of INVR-0xA / INVR-0xPOE series NVR
TABLE OF CONTENTS
Product Key Features ...................................................................................................................................... 4
Chapter 1 Introduction ................................................................................................................................... 9
1.1
Front Panel .................................................................................................................................... 10
1.2
IR Remote Control Operations ...................................................................................................... 11
1.3
USB Mouse Operation .................................................................................................................. 14
1.4
Input Method Description .............................................................................................................. 15
1.5
Menu Operation ............................................................................................................................. 16
1.6
Rear Panel ..................................................................................................................................... 17
Chapter 2 Getting Started ............................................................................................................................ 18
2.1
Starting Up and Shutting Down the NVR...................................................................................... 19
2.2
Using the Wizard for Basic Configuration..................................................................................... 20
2.3
Adding and Connecting the IP Cameras ........................................................................................ 24
2.3.1
Adding the Online IP Cameras .................................................................................... 24
2.3.2
Editing the Connected IP cameras and Configuring Customized Protocols ................ 26
2.3.3
Editing IP cameras connected to the PoE interfaces .................................................... 29
Chapter 3 Live View ..................................................................................................................................... 31
3.1
Introduction of Live View ............................................................................................................. 32
3.2
Operations in Live View Mode ...................................................................................................... 33
3.2.1
Using the Mouse in Live View .................................................................................... 33
3.2.2
Quick Setting Toolbar in Live View Mode.................................................................. 34
3.3
Adjusting Live View Settings ........................................................................................................ 36
3.4
User Logout ................................................................................................................................... 38
Chapter 4 PTZ Controls ............................................................................................................................... 39
4.1
Configuring PTZ Settings .............................................................................................................. 40
4.2
Setting PTZ Presets, Patrols & Patterns......................................................................................... 41
4.3
4.2.1
Customizing Presets .................................................................................................... 41
4.2.2
Calling Presets ............................................................................................................ 42
4.2.3
Customizing Patrols .................................................................................................... 43
4.2.4
Calling Patrols ............................................................................................................. 44
4.2.5
Customizing Patterns .................................................................................................. 45
4.2.6
Calling Patterns ........................................................................................................... 46
PTZ Control Toolbar ..................................................................................................................... 47
Chapter 5 Record Settings ........................................................................................................................... 48
5.1
Configuring Recording Parameters ............................................................................................... 49
5.2
Configuring Record Schedule........................................................................................................ 51
5.3
Configuring Motion Detection Record .......................................................................................... 54
5.4
Manual Record .............................................................................................................................. 56
5.5
Configuring Holiday Record ......................................................................................................... 57
5.6
Configuring HDD Group for Recording ........................................................................................ 60
5.7
Files Protection .............................................................................................................................. 61
6
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 6 Playback ...................................................................................................................................... 63
6.1
6.2
Playing Back Record Files ............................................................................................................ 64
6.1.1
Playing Back by Channel ............................................................................................ 64
6.1.2
Playing Back by Time ................................................................................................. 66
6.1.3
Playing Back by Event Search .................................................................................... 68
6.1.4
Playing Back by Tag ................................................................................................... 70
6.1.5
Playing Back by System Logs ..................................................................................... 73
6.1.6
Playing Back External File .......................................................................................... 75
Auxiliary Functions of Playback ................................................................................................... 76
6.2.1
Playing Back Frame by Frame .................................................................................... 76
6.2.2
Smart Search ............................................................................................................... 76
6.2.3
Digital Zoom ............................................................................................................... 79
6.2.4
Reverse Playback of Multi-channel ............................................................................ 79
Chapter 7 Backup ......................................................................................................................................... 81
7.1
7.2
Backing up Record Files................................................................................................................ 82
7.1.1
Backing up by Normal Video Search .......................................................................... 82
7.1.2
Backing up by Event Search ....................................................................................... 86
7.1.3
Backing up Video Clips............................................................................................... 89
Managing Backup Devices ............................................................................................................ 91
Chapter 8 Alarm Settings ............................................................................................................................. 94
8.1
Setting Motion Detection Alarm .................................................................................................... 95
8.2
Detecting Video Loss Alarm .......................................................................................................... 97
8.3
Detecting Video Tampering Alarm ................................................................................................ 99
8.4
Handling Exceptions Alarm......................................................................................................... 101
Chapter 9 Network Settings ........................................................................................................................ 102
9.1
Configuring General Settings ...................................................................................................... 103
9.2
Configuring Advanced Settings ................................................................................................... 104
9.2.1
Configuring PPPoE Settings ..................................................................................... 104
9.2.2
Configuring DDNS ................................................................................................... 104
9.2.3
Configuring NTP Server ........................................................................................... 107
9.2.4
Configuring SNMP ................................................................................................... 108
9.2.5
Configuring Remote Alarm Host .............................................................................. 109
9.2.6
Configuring Multicast ............................................................................................... 109
9.2.7
Configuring RTSP ..................................................................................................... 110
9.2.8
Configuring Server and HTTP Ports ......................................................................... 110
9.2.9
Configuring HTTPS Port .......................................................................................... 111
9.2.10
Configuring Email..................................................................................................... 111
9.2.11
Configuring UPnP™ ................................................................................................. 113
9.2.12
Configuring High-speed Download .......................................................................... 114
9.3
Checking Network Traffic ........................................................................................................... 116
9.4
Configuring Network Detection .................................................................................................. 117
9.4.1
Testing Network Delay and Packet Loss ................................................................... 117
9.4.2
Exporting Network Packet ........................................................................................ 117
9.4.3
Checking the Network Status .................................................................................... 118
7
User Manual of INVR-0xA / INVR-0xPOE series NVR
9.4.4
Checking Network Statistics ..................................................................................... 119
Chapter 10 HDD Management ................................................................................................................... 120
10.1 Initializing HDDs ........................................................................................................................ 121
10.2 Managing Network HDD ............................................................................................................ 123
10.3 Managing HDD Group ................................................................................................................ 125
10.3.1
Setting HDD Groups ................................................................................................. 125
10.3.2
Setting HDD Property ............................................................................................... 126
10.4 Configuring Quota Mode............................................................................................................. 128
10.5 Checking HDD Status ................................................................................................................. 130
10.6 HDD Detection ............................................................................................................................ 131
10.7 Configuring HDD Error Alarms .................................................................................................. 133
Chapter 11 Camera Settings ....................................................................................................................... 134
11.1 Configuring OSD Settings ........................................................................................................... 135
11.2 Configuring Privacy Mask ........................................................................................................... 136
11.3 Configuring Video Parameters..................................................................................................... 137
Chapter 12 NVR Management and Maintenance ..................................................................................... 138
12.1 Viewing System Information ....................................................................................................... 139
12.1.1
Viewing Device Information ..................................................................................... 139
12.1.2
Viewing Camera Information .................................................................................... 139
12.1.3
Viewing Record Information ..................................................................................... 139
12.1.4
Viewing Network Information .................................................................................. 140
12.1.5
Viewing HDD Information........................................................................................ 140
12.2 Searching & Export Log Files ..................................................................................................... 141
12.3 Importing/Exporting Configuration Files .................................................................................... 144
12.4 Upgrading System ....................................................................................................................... 145
12.4.1
Upgrading by Local Backup Device ......................................................................... 145
12.4.2
Upgrading by FTP ..................................................................................................... 145
12.5 Restoring Default Settings ........................................................................................................... 147
Chapter 13 Others........................................................................................................................................ 148
13.1 Configuring General Settings ...................................................................................................... 149
13.2 Configuring DST Settings ........................................................................................................... 150
13.3 Configuring More Settings for Device Parameters ...................................................................... 151
13.4 Managing User Accounts............................................................................................................. 152
13.4.1
Adding a User ........................................................................................................... 152
13.4.2
Deleting a User ......................................................................................................... 155
13.4.3
Editing a User ........................................................................................................... 155
Appendix ..................................................................................................................................................... 157
Glossary ................................................................................................................................................. 158
Troubleshooting ..................................................................................................................................... 159
List of Compatible IP Cameras .............................................................................................................. 165
8
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 1 Introduction
9
User Manual of INVR-0xA / INVR-0xPOE series NVR
1.1 Front Panel
Figure 1. 1 INVR-0xPOEand INVR-0xA
Table 1. 1 Description of Front Panel
No.
1
Name
Status
Indicator
Description
Power
Power indicator turns yellow when system is running.
Status
Status indicator blinks red when data is being read from or written to HDD.
TX/RX indictor blinks yellow when network connection is functioning
Tx/Rx
properly.
Universal Serial Bus (USB) ports for additional devices such as USB mouse
2
USB Interface
and USB Hard Disk Drive (HDD).
Table 1. 2 Description of Front Panel
No.
Name
Description
1
HDD Status Indicators
The corresponding indicator blinks when the HDD is being read or written.
2
Panel Lock
You can lock or unlock the panel by the key.
3
Running Status Indicator
The indicator lights when the device is running.
4
USB Interface
Universal Serial Bus (USB) ports for additional devices such as USB mouse
and USB Hard Disk Drive (HDD).
10
User Manual of INVR-0xA / INVR-0xPOE series NVR
1.2 IR Remote Control Operations
The NVR may also be controlled with the included IR remote control, shown in Figure 1. 2.
Batteries (2×AAA) must be installed before operation.
Figure 1. 2 Remote Control
Table 1. 3 Description of the Soft Keyboard Icons
No.
Name
Description
1
POWER
Power on/off the device.
2
DEV
Enables/Disables Remote Control.
3
Alphanumeric Buttons
Switch to the corresponding channel in Live view or PTZ Control mode.
Input numbers and characters in Edit mode.
Switch between different channels in All-day Playback mode.
4
EDIT Button
Edit text fields. When editing text fields, it will also function as a
Backspace button to delete the character in front of the cursor.
On checkbox fields, pressing the button will tick the checkbox.
In PTZ Control mode, the button adjusts the iris of the camera.
In Playback mode, it can be used to generate video clips for backup.
Enter/exit the folder of USB device.
5
A Button
Adjust focus in the PTZ Control menu.
11
User Manual of INVR-0xA / INVR-0xPOE series NVR
No.
Name
Description
It is also used to switch between input methods (upper and lowercase
alphabet, symbols and numeric input).
6
REC Button
Enter the Manual Record setting menu.
In PTZ control settings, press the button and then you can call a PTZ preset
by pressing Numeric button.
It is also used to turn audio on/off in the Playback mode.
7
PLAY Button
8
INFO Button
Reserved.
9
VOIP Button
Switch between main and spot output.
The button is used to enter the All-day Playback mode.
It is also used to auto scan in the PTZ Control menu.
In PTZ Control mode, it can be used to zoom out the image.
10
MENU Button
Press the button will help you return to the Main menu (after successful
login).
Press and hold the button for 5 seconds will turn off audible key beep.
In PTZ Control mode, the MENU/WIPER button will start wiper (if
applicable).
In Playback mode, it is used to show/hide the control interface.
11
PREV Button
Switch between single screen and multi-screen mode.
In PTZ Control mode, it is used to adjust the focus in conjunction with the
A/FOCUS+ button.
12
DIRECTION Button
Navigate between different fields and items in menus.
In the Playback mode, the Up and Down button is used to speed up and
slow down recorded video. The Left and Right button will select the next
and previous record files .
In Live View mode, these buttons can be used to cycle through channels.
In PTZ control mode, it can control the movement of the PTZ camera.
ENTER Button
Confirm selection in any of the menu modes.
It can also be used to tick checkbox fields.
In Playback mode, it can be used to play or pause the video.
In single-frame Playback mode, pressing the button will advance the video
by a single frame.
13
PTZ Button
In Auto-switch mode, it can be used to stop /start auto switch.
14
ESC Button
Back to the previous menu.
Press for Arming/disarming the device in Live View mode.
15
RESERVED
Reserved for future usage.
16
F1 Button
Select all items on the list when used in a list field.
In PTZ Control mode, it will turn on/off PTZ light (if applicable).
In Playback mode, it is used to switch between play and reverse play.
17
PTZ Control Buttons
Buttons to adjust the iris, focus and zoom of a PTZ camera.
18
F2 Button
Cycle through tab pages.
In synchronous playback mode, it is used to switch between channels.
12
User Manual of INVR-0xA / INVR-0xPOE series NVR
Troubleshooting Remote Control:
Make sure you have installed batteries properly in the remote control. And you have to aim the remote
control at the IR receiver in the front panel.
If there is no response after you press any button on the remote, follow the procedure below to troubleshoot.
Steps:
1. Go to Menu > Settings > General > More Settings by operating the front control panel or the mouse.
2. Check and remember NVR ID#. The default ID# is 255. This ID# is valid for all the IR remote controls.
3. Press the DEV button on the remote control.
4. Enter the NVR ID# you set in step 2.
5. Press the ENTER button on the remote.
If the Status indicator on the front panel turns blue, the remote control is operating properly. If the Status indicator
does not turn blue and there is still no response from the remote, please check the following:
 Batteries are installed correctly and the polarities of the batteries are not reversed.
 Batteries are fresh and not out of charge.
 IR receiver is not obstructed.
If the remote still can’t function properly, please change a remote and try again, or contact the device provider.
13
User Manual of INVR-0xA / INVR-0xPOE series NVR
1.3 USB Mouse Operation
A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse:
1. Plug USB mouse into one of the USB interfaces on the front panel of the NVR.
2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible
reason may be that the two devices are not compatible, please refer to the recommended the device list from
your provider.
The operation of the mouse:
Table 1. 4 Description of the Mouse Control
Name
Action
Single-Click
Double-Click
Left-Click
Description
Live view: Select channel and show the quick set menu.
Menu: Select and enter.
Live view: Switch between single-screen and multi-screen.
PTZ control: pan, tilt and zoom.
Click and Drag
Video tampering, privacy mask and motion detection: Select target area.
Digital zoom-in: Drag and select target area.
Live view: Drag channel/time bar.
Right-Click
Single-Click
Scrolling up
Scroll-Wheel
Live view: Show menu.
Menu: Exit current menu to upper level menu.
Live view: Previous screen.
Menu: Previous item.
Live view: Next screen.
Scrolling down
Menu: Next item.
14
User Manual of INVR-0xA / INVR-0xPOE series NVR
1.4 Input Method Description
Figure 1. 3 Soft Keyboard
Description of the buttons on the soft keyboard:
Table 1. 5 Description of the Soft Keyboard Icons
Icons
Description
Icons
/
Lowercase/Uppercase
Symbols
Space
Backspace
Exit
Enter
15
Description
User Manual of INVR-0xA / INVR-0xPOE series NVR
1.5 Menu Operation
After entering the menu, the menu bar on the top of the screen can be clicked to set other functions.
Figure 1. 4 Menu Bar
From the left to the right, each icon stands for Playback, Export, Manual, HDD, Record, Camera, Configuration,
Maintenance and Shutdown. And the current submenu you are in is marked in the light green.
16
User Manual of INVR-0xA / INVR-0xPOE series NVR
1.6 Rear Panel
Figure 1. 5 INVR-0xA
Table 1. 6 Description of Rear Panel Interfaces
No.
Item
Description
1
LAN Interfaces
Connector for LAN (Local Area Network).
2
RS-485 Interface
Connector for RS-485 devices.
3
Power Supply
12VDC power supply.
4
Power Switch
Switch for turning on/off the device.
5
USB
Connects USB disks and devices.
6
Ground
Ground (needs to be connected when NVR starts up).
7
HDMI
HDMI video output connector.
8
VGA
9
AUDIO IN
BNC connector for audio input. (Also for two-way audio)
10
AUDIO OUT
BNC connector for audio output.
D-SUB connector for VGA output. Display local video output and
menu.
Figure 1. 6 INVR-0xPOE
No.
Item
Description
1
LAN Network Interface
Connector for LAN (Local Area Network).
2
RS-485 Interface
Connects to RS-485 devices.
3
Power Supply
100~240VAC power supply
4
Power Switch
Switch for turning on/off the device.
Universal Serial Bus (USB) ports for additional devices such as USB
5
USB Interface
6
GND
Ground (needs to be connected when NVR starts up).
7
HDMI Interface
HDMI video output connector.
8
VGA Output
9
Audio In
RCA connector for voice talk input
10
Audio Out
RCA connector for audio output
mouse and USB Hard Disk Drive (HDD).
D-SUB connector for VGA output. Display local video output and
menu.
17
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 2
Getting Started
18
User Manual of INVR-0xA / INVR-0xPOE series NVR
2.1 Starting Up and Shutting Down the NVR
Purpose:
Proper startup and shutdown procedures are crucial to expanding the life of the NVR.
Before you start:
Check that the voltage of the extra power supply is the same with the NVR’s requirement, and the ground
connection is working properly.
Starting up the NVR:
Steps:
1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an
Uninterruptible Power Supply (UPS) be used in conjunction with the device.
2. Turn on the power switch on the rear panel.
3. After startup, the Power LED indicator turns on (supported by INVR-0xA series NVR only).
Shutting down the NVR
Steps:
1. Enter the Shutdown menu.
Menu > Shutdown
Figure 2. 1 Shutdown Menu
2. Click the Shutdown button.
3. Click the Yes button.
4. Turn off the power switch on the rear panel when the attention pops up.
Figure 2. 2 Shutdown Attention
Rebooting the NVR
In the Shutdown menu, you can also reboot the NVR.
Steps:
1. Enter the Shutdown menu by clicking Menu > Shutdown.
2. Click the Logout button to lock the NVR or the Reboot button to reboot the NVR.
19
User Manual of INVR-0xA / INVR-0xPOE series NVR
2.2 Using the Wizard for Basic Configuration
By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure below.
Select the system language in the drop-down list, and click the Apply button to save the setting.
Figure 2. 3 Language Selection Interface
Figure 2. 4 Start Wizard Interface
Operating the Setup Wizard:
1. The Setup Wizard can walk you through some important settings of the NVR. If you don’t want to use the
Setup Wizard at that moment, click the Exit button. You can also choose to use the Setup Wizard next time
by leaving the “Start wizard when the device starts?” checkbox checked.
2. Click Next button on the Wizard window to enter the Login window, as shown in Figure 2. 5.
20
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 2. 5 Login Window
3. Enter the admin password. By default, the password is 12345.
4. To change the admin password, check the New Admin Password checkbox. Enter the new password and
confirm the password in the given fields.
5. Click the Next button to enter the date and time settings window, as shown in Figure 2. 6.
Figure 2. 6 Date and Time Settings
6. After the time settings, click Next button which takes you back to the Network Setup Wizard window, as
shown in Figure 2. 7.
INVR-0xA
21
User Manual of INVR-0xA / INVR-0xPOE series NVR
INVR-0xPOE
Figure 2. 7 Network Configuration
7. Click Next button after you configured the network parameters, which takes you to the HDD Management
window, shown in Figure 2. 8.
Figure 2. 8 HDD Management
8. To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.
9. Click Next button to enter the Adding IP Camera interface.
10. Click Search to find online IP Camera. Select the IP camera to be added, and click the Add button.
Figure 2. 9 Search for IP Cameras
22
User Manual of INVR-0xA / INVR-0xPOE series NVR
11. Click Next button. Configure the recording for the searched IP Cameras.
Figure 2. 10 Record Settings
12. Click Copy to copy the settings to other channels, as shown in Figure 2. 11.
Figure 2. 11 Copy Record Settings
13. Click OK to complete the startup Setup Wizard.
23
User Manual of INVR-0xA / INVR-0xPOE series NVR
2.3 Adding and Connecting the IP Cameras
2.3.1 Adding the Online IP Cameras
Purpose:
The main function of the NVR is to connect the network cameras and record the video got from it. So before you
can get a live view or record of the video, you should add the network cameras to the connection list of the device.
Before you start:
Ensure the network connection is valid and correct. For detailed checking and configuring of the network, please
see Chapter Checking Network Traffic and Chapter Configuring Network Detection.
•
OPTION 1:
Steps:
1.
Right-click the mouse when you in the live view mode to show the right-click menu bar.
Figure 2. 12 Right-click Menu Bar
2.
Select

(Auto) or
(Manual) on your demand.
Auto
The device will add the detected IP cameras or encoders automatically by the default user name and password
of administrator.
Figure 2. 13 Auto Adding IP Camera Interface
If the user name and password is changed, the auto adding of IP camera will be failed, you may add it
manually.

Manual
Steps:
1.
To add the online cameras with same network segment:
1)
The detected online camera will be listed in the camera list, as shown in the figure below.
24
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 2. 14 Manual Adding IP Camera Interface
2)
Click the
button to add the camera.
Explanation of the icons:
Icon
Explanation
Icon
Explanation
Edit basic parameters of the camera
Add the detected IP camera.
The camera is connected; you can
The camera is disconnected; you can
click the icon to get the live view of
click the icon to get the exception
the camera.
information of camera.
The camera is connected.
Advanced settings of the camera.
Delete the IP camera
2.
To add other IP cameras:
1)
Click the Custom Add button to pop up the Add IP Camera (Custom) interface.
Figure 2. 15 Custom Adding IP Camera Interface
2)
You can edit the IP address, protocol, management port, and other information of the IP camera to
be added.
3)
•
Click Add to add the camera.
OPTION 2:
Steps:
25
User Manual of INVR-0xA / INVR-0xPOE series NVR
1.
Enter the Camera Management interface.
Menu> Camera> Camera
Figure 2. 16 Menu
2.
Repeat the step 1 and 2 of adding IP cameras manually to add the camera.
Figure 2. 17 IP Camera Management Interface
2.3.2 Editing the Connected IP cameras and Configuring
Customized Protocols
After the adding of the IP cameras, the basic information of the camera lists in the page, you can configure the
basic setting of the IP cameras.
Steps:
1.
Click the
icon to edit the parameters; you can edit the IP address, protocol and other parameters.
26
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 2. 18 Edit the Parameters
2.
Click OK to save the settings and exit the editing interface.
To edit advanced parameters:
1.
Drag the horizontal scroll bar to the right side and click the
icon.
Figure 2. 19 Network Configuration of the Camera
2.
You can edit the network information and the password of the camera.
Figure 2. 20 Password Configuration of the Camera
27
User Manual of INVR-0xA / INVR-0xPOE series NVR
3.
Click Apply to save the settings and click OK to exit the interface.
Configuring the customized protocols
Purpose:
To connect the network cameras which are not configured with the standard protocols, you can configure the
customized protocols for them.
Steps:
1.
Click the Protocol button in the Add IP Camera (Custom) interface to enter the protocol management
interface.
Figure 2. 21 Protocol Management Interface
There are 16 customized protocols provided in the system, you can edit the protocol name; and choose whether to
enable the sub-stream.
2.
Choose the protocol type of transmission and choose the transfer protocols.
The protocol type and the transfer protocols must be supported by the connected network camera.
After adding the customized protocols, you can see the protocol name is listed in the dropdown list, please refer to
Figure 2. 22.
Figure 2. 22 Protocol Setting
3.
Choose the protocols you just added to validate the connection of the network camera.
28
User Manual of INVR-0xA / INVR-0xPOE series NVR
2.3.3 Editing IP cameras connected to the PoE interfaces
The PoE interfaces enables the NVR system to pass electrical power safely, along with data, on Ethernet cabling to
the connected network cameras.
The PoE series NVR provides up to 8 PoE interfaces which can connect to 8 network cameras directly; and if you
disable the PoE interface, you can also connect to the online network cameras. And the PoE interface supports the
Plug-and-Play function.
Example:
As for 7604NI-SE/P NVR, when you want to connect 1 online camera and connect 3 network cameras via PoE
interfaces, you must disable 1 PoE interface in the Edit IP camera panel.
To add Cameras for NVR supporting PoE function:
Before you start:
Connect the network cameras via the PoE interfaces.
Steps:
1.
Enter the Camera Management interface.
Main menu> Camera> Camera
You can see the connected cameras are listed.
Figure 2. 23 Camera List
The cameras connecting to the PoE interface cannot be deleted in this menu.
2.
Click the
•
button, and select the Adding Method in the drop-down list.
Plug-and-Play: It means that the camera is connected to the PoE interface, so in this case, the
parameters of the camera can’t be edited. The IP address of the camera can only be edited in the
Network Configuration interface, see Chapter 9.1 Configuring General Settings for detailed
information.
29
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 2. 24 Edit IP Camera Interface - Plug-and-Play
•
Manual: You can disable the PoE interface by selecting the manual while the current channel can be
used as a normal channel and the parameters can also be edited.
Figure 2. 25 Edit IP Camera Interface – Manual
3.
Click the Apply button to finish adding.
This section is only applicable for the PoE series NVR.
30
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 3
Live View
31
User Manual of INVR-0xA / INVR-0xPOE series NVR
3.1 Introduction of Live View
Live view shows you the video image getting from each camera in real time. The NVR automatically enters Live
View mode when powered on.
Live View Icons
In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can know whether the channel is recorded, or whether there are alarms
occur as soon as possible.
Table 3. 1 Description of Live View Icons
Icons
Description
Alarm (video loss, tampering, motion detection or sensor alarm)
Record (manual record, schedule record, motion detection or alarm triggered record)
Alarm & Record
32
User Manual of INVR-0xA / INVR-0xPOE series NVR
3.2 Operations in Live View Mode
In live view mode, there are many functions provided. The functions are listed below.
•
•
•
Single Screen: showing only one screen on the monitor.
Multi-screen: showing multiple screens on the monitor simultaneously.
Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen on
the configuration menu before enabling the auto-switch.
Menu>Configuration>Live View>General.
•
•
•
•
Start Recording: continuous record and motion detection record are supported.
Output Mode: select the output mode to Standard, Bright, Gentle or Vivid.
Playback: playback the recorded videos for current day.
Add IP Camera: The shortcut to add IP camera automatically or manually.
3.2.1 Using the Mouse in Live View
Table 3. 2 Mouse Operation in Live View
Icon
Description
Enter the menu of the system by clicking the icon.
Switch to the single full screen.
Adjust the screen layout by clicking the specific icon.
Switch to the previous/next screen.
/
Enable/disable the auto-switch of the screens.
Start continuous recording or motion detection recording of all channels.
Add IP camera automatically or manually.
Enter the playback interface and start playing back the video of the selected
channel immediately.
Four modes of output supported, including Standard, Bright, Gentle and Vivid.
 The dwell time of the live view configuration must be set before using Start Auto-switch.
 If the corresponding camera supports intelligent function, the Reboot Intelligence option is included when
right-clicking mouse on this camera.
Figure 3. 1 Right-click Menu Bar
33
User Manual of INVR-0xA / INVR-0xPOE series NVR
 Two ways are provided to show the Right-click Menu Bar: right-clicking or moving the mouse to the bottom of the
screen.
 You can click
on the right side of the menu bar to fix the menu.
3.2.2 Quick Setting Toolbar in Live View Mode
On the screen of each channel, there is a quick setting toolbar which shows when you single click the mouse in the
corresponding screen.
Figure 3. 2 Quick Setting Toolbar
Table 3. 3 Description of Quick Setting Toolbar Icons
Icons
Description
Enable/Disable
/
Instant Record
PTZ Control
Icons
Description
Icons
Description
Instant Playback
/
Mute/Audio on
Digital Zoom
Live View
Image Settings
Close
Strategy
Instant Playback only shows the record in last five minutes. If no record is found, it means there is no record
during the last five minutes.
Digital Zoom can zoom in the selected area to the full screen. You can click and draw to select the area to
zoom in, as shown in Figure 3. 3.
34
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 3. 3 Digital Zoom
Image Settings icon can be selected to enter the Image Settings menu.
You can set the image parameters like brightness, contrast, saturation and hue.
Figure 3. 4 Image Settings- Customize
Live View Strategy can be selected to set strategy, including Real-time, Balanced, Fluency.
Figure 3. 5 Live View Strategy
35
User Manual of INVR-0xA / INVR-0xPOE series NVR
3.3 Adjusting Live View Settings
Purpose:
Live View settings can be customized according to different needs. You can configure the output interface, dwell
time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc.
Steps:
1. Enter the Live View Settings interface.
Menu> Configuration> Live View
Figure 3. 6 Live View-General
The settings available in this menu include:
•
Video Output Interface: Designates the output to configure the settings for. Only VGA/HDMI is
selectable by default.
•
•
Live View Mode: Designates the display mode to be used for Live View.
Dwell Time: The time in seconds to dwell between switching of channels when enabling auto-switch
in Live View.
•
•
•
Enable Audio Output: Enables/disables audio output for the selected video output.
Event Output: Designates the output to show event video.
Full Screen Monitoring Dwell Time: The time in seconds to show alarm event screen.
2. Setting Cameras Order
Figure 3. 7 Live View- Camera Order
36
User Manual of INVR-0xA / INVR-0xPOE series NVR
To set the camera order:
1)
Select a View mode in
2)
Select the small window, and double-click on the channel number to display the channel on the
window.
You can click
button to start live view for all the channels and click
live view.
3)
Click the Apply button to save the setting.
37
to stop all the
User Manual of INVR-0xA / INVR-0xPOE series NVR
3.4 User Logout
Purpose:
After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to enter
user name and password tog in again.
Steps:
1. Enter the Shutdown menu.
Menu>Shutdown
Figure 3. 8 Shutdown
2. Click Logout.
After you have logged out the system, menu operation on the screen is invalid. It is required to input a user
name and password to unlock the system.
38
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 4 PTZ Controls
39
User Manual of INVR-0xA / INVR-0xPOE series NVR
4.1 Configuring PTZ Settings
Purpose:
Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before
you control the PTZ camera.
Steps:
1. Enter the PTZ Settings interface.
Menu >Camera> PTZ
Figure 4. 1 PTZ- General
2. Choose the camera for PTZ setting in the Camera dropdown list.
3. Enter the parameters of the PTZ camera.
All the parameters should be exactly the same as the PTZ camera parameters.
Example: If the PTZ camera uses the protocol of DRAGON, you should select DRAGON in the PTZ
Protocol field.
4. Click Apply button to save the settings.
40
User Manual of INVR-0xA / INVR-0xPOE series NVR
4.2 Setting PTZ Presets, Patrols & Patterns
Before you start:
Please make sure that the presets, patrols and patterns should be supported by PTZ protocols.
4.2.1 Customizing Presets
Purpose:
Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place.
Steps:
1. Enter the PTZ Control interface.
Menu>Camera>PTZ>More Settings
Figure 4. 2 PTZ- More Settings
2.
Use the directional button to wheel the camera to the location where you want to set preset.
3.
Click the round icon before Save Preset.
4.
Click the preset number to save the preset.
Repeat the steps2-4 to save more presets. If the number of the presets you want to save is more than 17, you can
click […] and choose the available numbers.
Figure 4. 3 More Presets
41
User Manual of INVR-0xA / INVR-0xPOE series NVR
4.2.2 Calling Presets
Purpose:
This feature enables the camera to point to a specified position such as a window when an event
takes place.
Call preset in the PTZ setting interface:
Steps:
1. Enter the PTZ Control interface.
Menu>Camera>PTZ>More Settings
2. Check the round icon of Call Preset.
Figure 4. 4 PTZ- Call Preset
3. Click to choose the preset number. If the number of the presets you want to save is more than 17, you can
click […] and choose the available numbers.
Call preset in live view mode:
Steps:
1. Press the PTZ button on the front panel or click the PTZ Control icon
the PTZ setting menu in live view mode.
Figure 4. 5 PTZ Toolbar
2. Choose Camera in the list on the menu.
3. Double click the preset in the Preset list to call it.
42
in the quick setting bar to enter
User Manual of INVR-0xA / INVR-0xPOE series NVR
4.2.3 Customizing Patrols
Purpose:
Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving
on to the next key point. The key points are corresponding to the presets. The presets can be set following the steps
above in Customizing Presets.
Steps:
1. Enter the PTZ Control interface.
Menu>Camera>PTZ>More Settings
2. Select patrol number in the drop-down list of patrol.
3. Select the
under Patrol option box to add key points for the patrol.
Figure 4. 6 PTZ- Add Key Point
4. Configure key point parameters, such as the key point No., duration of staying for one key point and speed of
patrol. The key point is corresponding to the preset. The Key Point No. determines the order at which the
PTZ will follow while cycling through the patrol. The Duration refers to the time span to stay at the
corresponding key point. The Speed defines the speed at which the PTZ will move from one key point to
the next.
Figure 4. 7 Key Point Configuration
5. Click OK to save the key point to the patrol.
Repeat the above steps to add more key points.
43
User Manual of INVR-0xA / INVR-0xPOE series NVR
Click the
icon to delete the corresponding key point, and click the trash icon
to delete all the key
points.
Select a key point, then click
or
button to adjust the order of the key points.
Figure 4. 8 Key Points Deletion
4.2.4 Calling Patrols
Purpose:
Calling a patrol makes the PTZ to move according the predefined patrol path.
Calling patrol in the PTZ setting interface:
Steps:
1. In the PTZ setting interface.
Menu> Camera> PTZ> More Settings
2. Select the patrol number, and then click
3. Click
to call the patrol.
to stop it.
Calling patrol in live view mode:
Steps:
1. Press PTZ control on the front panel or on the remote, or click PTZ Control icon
toolbar, to show the PTZ control toolbar.
2. Choose Patrol on the control bar.
3. Double click the patrol or select the patrol and click
44
to call it.
on the quick setting
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 4. 9 PTZ Toolbar- Patrol
4.2.5 Customizing Patterns
Purpose:
Patterns can be set by recording the movement of the PTZ. You can call the pattern to make the PTZ movement
according to the predefined path.
Steps:
1. Enter the PTZ Control interface.
Menu>Camera>PTZ>More Settings
2. Choose pattern number in the option box.
Figure 4. 10 PTZ- Pattern
3. Click
and use your mouse to drag the image or click the eight directional buttons in the control box
under the image to move the PTZ camera.
The movement of the PTZ is recorded as the pattern.
4. Click
to save the pattern.
45
User Manual of INVR-0xA / INVR-0xPOE series NVR
4.2.6 Calling Patterns
Purpose:
Follow the procedure to move the PTZ camera according to the predefined patterns.
Calling pattern in the PTZ setting interface
Steps:
1. Enter the PTZ Control interface.
Menu>Camera>PTZ>More Settings
2. Select the pattern number.
3. Click
, then the PTZ moves according to the pattern. Click
to stop it.
Call pattern in live view mode
Steps:
1. In the live view mode, press PTZ control on the front panel or on the remote control, or click PTZ Control
icon
on the quick setting toolbar.
2. And then choose Pattern on the control bar.
3. Double click the pattern or select the pattern and click
46
to call it.
User Manual of INVR-0xA / INVR-0xPOE series NVR
4.3 PTZ Control Toolbar
In the Live View mode, you can press the PTZ Control button on the front panel or on the remote control, or
choose the PTZ Control icon
to enter the PTZ toolbar.
PTZ Toolbar
Table 4. 1 Description of the PTZ toolbar icons
Icon
Description
Icon
Description
Direction button and
Zoom+,
the auto-cycle button
Focus+, Iris+
The speed of the
Light on/off
PTZ movement
Image
3D-Zoom
Centralization
Icon
Description
Zoom-, Focus-, Iris-
Wiper on/off
Preset
Patrol
Pattern
Menu
Previous item
Next item
Start pattern/patrol
Stop the patrol or
Minimize
pattern movement
windows
47
Exit
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 5 Record Settings
48
User Manual of INVR-0xA / INVR-0xPOE series NVR
5.1 Configuring Recording Parameters
Purpose:
By configuring the recording parameters you can define the parameters which affect the image quality, such as the
transmission stream type, the resolution and so on.
Before you start:
1. Make sure that the HDD has already been installed. If not, please install a HDD and initialize it.
(Menu>HDD>General)
Figure 5. 1 HDD- General
2. Check the storage mode of the HDD
1)
Click Advanced to check the storage mode of the HDD.
2)
If the HDD mode is Quota, please set the maximum record capacity. For detailed information, see
Chapter Configuring Quota Mode.
3)
If the HDD mode is Group, you should set the HDD group. For detailed information, see Chapter
Configuring HDD Group for Recording.
Figure 5. 2 HDD- Advanced
Steps:
1. Enter the Record settings interface to configure the recording parameters:
Menu>Record> Parameters
Figure 5. 3 Recording Parameters
49
User Manual of INVR-0xA / INVR-0xPOE series NVR
2. Parameters Setting for Recording
1)
Select Record tab page to configure. You can configure the stream type, the resolution, and other
parameters on your demand.
• Pre-record: The time you set to record before the scheduled time or event. For example, when an
alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera
records it at 9:59:55.
• Post-record: The time you set to record after the event or the scheduled time. For example, when
an alarm triggered the recording ends at 11:00, if you set the post-record time as 5 seconds, it
records till 11:00:05.
• Expired Time: The expired time is the longest time for a record file to be kept in the HDD, if the
deadline is reached, the file will be deleted. You can set the expired time to 0, and then the file will
not be deleted. The actual keeping time for the file should be determined by the capacity of the
HDD.
• Redundant Record: Enabling redundant record means you save the record in the redundant HDD.
See Chapter Configuring Redundant Recording.
• Record Audio: Check the checkbox to enable or disable audio recording.
2)
Click Apply to save the settings.
 The redundant record is to decide whether you want the camera to save the record files in the redundant
HDD. You must configure the redundant HDD in HDD settings. For detailed information, see Chapter
10.3.2 Setting HDD Property.
 The parameters of Main Stream (Event) are read-only.
3. Parameters Settings for Sub-stream
1)
Enter the Sub-stream setting interface by clicking the Substream tab.
Figure 5. 4 Sub-stream Parameters
2)
Configure the parameters of the camera.
3)
Click Apply to save the settings.
50
User Manual of INVR-0xA / INVR-0xPOE series NVR
5.2 Configuring Record Schedule
Purpose:
Set the record schedule, and then the camera automatically starts/stops recording according to the configured
schedule.
Steps:
1. Enter the Record Schedule interface.
Menu>Record>Schedule
2. Configure Record Schedule
1) Select Record Schedule.
Figure 5. 5 Record Schedule
2) Choose the camera you want to configure.
3) Select the check box after the Enable Schedule item.
4) Click Edit button or click on the color icon under the edit button and draw the schedule line on the panel.
Edit the schedule:
I.
In the message box, you can choose the day to which you want to set schedule.
Figure 5. 6 Recording Schedule Interface
You can click the
button to set the accurate time of the schedule.
II.
To schedule an all-day recording, check the checkbox after the All Day item.
Figure 5. 7 Edit Schedule
III.
To arrange other schedule, leave the All Day checkbox blank and set the Start/End time.
Up to 8 periods can be configured for each day. And the time periods can’t be overlapped each other.
51
User Manual of INVR-0xA / INVR-0xPOE series NVR
Repeat the above edit schedule steps to schedule recording for other days in the week. If the schedule can
also be applied to other days, click Copy.
Figure 5. 8 Copy Schedule to Other Days
IV.
Click OK to save setting and back to upper level menu.
V.
Click Apply in the Record Schedule interface to save the settings.
Draw the schedule:
Click on the color icons, you can choose the schedule type as continuous or event.
Figure 5. 9 Draw the Schedule
Descriptions of the color icons are shown in the figure below.
Figure 5. 10 Descriptions of the color icons
52
User Manual of INVR-0xA / INVR-0xPOE series NVR
Click the Apply button to validate the settings.
If the settings can also be used to other channels, click Copy, and then choose the channel to which you
want to copy.
Figure 5. 11 Copy Schedule to Other Channels
53
User Manual of INVR-0xA / INVR-0xPOE series NVR
5.3 Configuring Motion Detection Record
Purpose:
Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes
place, the NVR can analyze it and do many actions to handle it. Enabling motion detection function can trigger
certain channels to start recording, or trigger full screen monitoring, audio warning, notify the surveillance center
and so on. In this chapter, you can follow the steps to schedule a record which triggered by the detected motion.
Steps:
1.
Enter the Motion Detection interface.
Menu>Camera>Motion
Figure 5. 12 Motion Detection
2.
Configure Motion Detection:
1) Choose camera you want to configure.
2) Check the checkbox after Enable Motion Detection.
3) Drag and draw the area for motion detection by mouse. If you want to set the motion detection for all
the area shot by the camera, click Full Screen. To clear the motion detection area, click Clear.
Figure 5. 13 Motion Detection- Mask
4) Click Setting, and the message box for channel information pop up.
54
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 5. 14 Motion Detection Setting
5) Select the channels which you want the motion detection event to trigger recording.
6) Click Apply to save the settings.
7) Click OK to back to the upper level menu.
8) Exit the Motion Detection menu.
3.
Edit the Motion Detection Record Schedule. For the detailed information of schedule configuration, see
Chapter Configuring Record Schedule.
55
User Manual of INVR-0xA / INVR-0xPOE series NVR
5.4 Manual Record
Purpose:
Follow the steps to set parameters for the manual record. The manual recording is prior to the scheduled recording.
Steps:
1.
Enter the Manual settings interface.
Menu> Manual
Or press the REC button on the remote control.
Figure 5. 15 Manual Record
2.
Enabling Manual Record
1) Select Record on the left bar.
2) Click the status button before camera number to change
3.
to
.
Disable manual record.
Click the status button to change
to
.
Green icon
means that the channel is configured the record schedule. After rebooting all the
manual records enabled are canceled.
56
User Manual of INVR-0xA / INVR-0xPOE series NVR
5.5 Configuring Holiday Record
Purpose:
Follow the steps to configure the record schedule on holiday for that year. You may want to have different plan for
recording on holiday.
Steps:
1.
Enter the Record setting interface.
Menu>Record> Holiday
Figure 5. 16 Holiday Settings
2.
Enable Edit Holiday schedule.
1)
Click
to enter the Edit interface.
Figure 5. 17 Edit Holiday Settings
2)
Check the checkbox after Enable Holiday.
3)
Select Mode from the dropdown list.
There are three different modes for the date format to configure holiday schedule.
4)
Set the start and end date.
5)
Click Apply to save settings.
6)
Click OK to exit the Edit interface.
57
User Manual of INVR-0xA / INVR-0xPOE series NVR
3.
Enter Record Schedule settings interface to edit the holiday recording schedule. See Chapter 6.2
Configuring Record Schedule.Configuring Redundant Recording
Purpose:
Enabling redundant recording, which means saving the record files not only in the R/W HDD but also in the
redundant HDD, will effectively enhance the data safety and reliability. .
Steps:
1. Enter HDD Information interface.
Menu> HDD
Figure 5. 18 HDD General
2. Select the HDD and click
1)
to enter the Local HDD Settings interface.
Set the HDD property to Redundancy.
Figure 5. 19 HDD General-Editing
2)
Click Apply to save the settings.
3)
Click OK to back to the upper level menu.
You must set the Storage mode in the HDD advanced settings to Group before you set the HDD property to
Redundant. For detailed information, please refer to Chapter 10.3 Managing HDD Group. There should be at
least another HDD which is in Read/Write status.
3. Enter the Record setting interface.
Menu> Record> Parameters
1)
Select Record tab.
58
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 5. 20 Record Parameters
2)
Select Camera you want to configure in the drop-down list.
3)
Check the checkbox of Redundant Record.
4)
Click Apply to save settings and back to the upper level menu.
Repeat the above steps for configuring other channels.
59
User Manual of INVR-0xA / INVR-0xPOE series NVR
5.6 Configuring HDD Group for Recording
Purpose:
You can group the HDDs and save the record files in certain HDD group.
Steps:
1.
Enter HDD setting interface.
Menu>HDD
Figure 5. 21 HDD General
2.
Select Advanced on the left bar.
Figure 5. 22 Storage Mode
Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information,
please refer to Chapter 12.4 Managing HDD Group.
3.
Select General in the left bar.
4.
Configuring HDD group.
Click
to enter editing interface.
1) Choose a group number for the HDD group.
2) Click Apply and then in the pop-up message box, click Yes to save your settings.
3) Click OK to back to the upper level menu.
Repeat the above steps to configure more HDD groups.
5.
Choose the Channels which you want to save the record files in the HDD group.
1) Select Advanced on the left bar.
2) Choose Group number in the dropdown list of Record on HDD Group
3) Check the channels you want to save in this group.
4) Click Apply to save settings.
After having configured the HDD groups, you can configure the recording settings following the
procedure provided in Chapter 5.2-5.7.
Eddig kész
60
User Manual of INVR-0xA / INVR-0xPOE series NVR
5.7 Files Protection
Purpose:
You can lock the recorded files or set the HDD property to Read-only to protect the record files from being
overwritten.
Protect file by locking the record files:
Steps:
1.
Enter Playback setting interface.
Menu > Export
Figure 5. 23 Export
2.
Select the channels you want to investigate by checking the checkbox to
3.
Configure the record type, file type start/end time.
4.
Click Search to show the results.
.
Figure 5. 24 Export- Search Result
5.
Protect the record files.
1)
Find the record files you want to protect, and then click the
icon which will turn to
indicating that the file is locked.
The record files of which the recording is still not completed can’t be locked.
2)
Click
to change it to
to unlock the file and the file is not protected.
61
,
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 5. 25 Unlocking Attention
Protect file by setting HDD property to Read-only
Steps:
1.
Enter HDD setting interface.
Menu> HDD
Figure 5. 26 HDD General
2.
Click
to edit the HDD you want to protect.
To edit HDD property, you need to set the storage mode of the HDD to Group. See Chapter
Managing HDD Group.
3.
Set the HDD property to Read-only in the pop-up editing interface.
4.
Click OK to save settings and back to the upper-level menu.
 No file can be saved in a Read-only HDD. If you want to save files in the HDD, change the property
to R/W.
 If there is only one HDD and is set to Read-only, the NVR cannot record any files. Only live view
mode is available.
 If you set the HDD to Read-only when the NVR is saving files in it, then the file will be saved in
next R/W HDD. If there is only one HDD, the recording will be stopped.
62
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 6 Playback
63
User Manual of INVR-0xA / INVR-0xPOE series NVR
6.1 Playing Back Record Files
6.1.1 Playing Back by Channel
Purpose:
Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported.

OPTION 1:
Choose a channel in live view mode using the mouse and click the
button in the quick setting toolbar.
In the instant playback mode, only record files recorded during the last five minutes on this channel will be
played back.
Figure 6. 1 Instant Playback Interface

OPTION 2:
1. Enter the Playback interface.
Right-click the mouse when you in the live view mode and select
from the menu.
Figure 6. 2 Right-click Menu under Live View
Under multi-screen live view mode, the recorded files of the top-left channel will be played back.
Pressing numerical buttons will switch playback to the corresponding channels during playback
process.
2. Playback management.
64
User Manual of INVR-0xA / INVR-0xPOE series NVR
The toolbar in the bottom part of Playback interface can be used to control playing progress, as shown in
Figure 6. 3.
Figure 6. 3 Playback Interface
Click the channel(s) to execute simultaneous playback of multiple channels.
Figure 6. 4 Toolbar of Playback
The
indicates the start/end time of the record.
Table 6. 1 Detailed Explanation of Playback Toolbar
Button
/
Operation
Audio on/
Button
/
Mute
tag
Pause reverse
Single-frame
reverse play
Start/Stop
/
Operation
30s forward
Add
Tag
customized tag
management
Pause play/
play/
Reverse play/
Button
clipping
Add default
/
Operation
Button
Operation
30s reverse
Speed down
Scaling
Play/
/
Single-frame
up/down the
Speed up
time line
play
Previous day
Next day
Full Screen
Exit
Stop
Digital Zoom
Smart Search
Video type
Process bar
65
User Manual of INVR-0xA / INVR-0xPOE series NVR
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
6.1.2 Playing Back by Time
Purpose:
Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel switch
are supported.
Steps:
1. Enter playback interface.
Menu>Playback
2. Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar.
Figure 6. 5 Playback Calendar
If there are record files for that camera in that day, in the calendar, the icon for that day is displayed as
Otherwise it is displayed as
displayed as
. And the selected date is surrounded by a green rectangle, which is
.
In the Playback interface:
The toolbar in the bottom part of Playback interface can be used to control playing process, as shown in Figure 6.
6.
66
.
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 6. 6 Interface of Playback by Time
Figure 6. 7 Toolbar of Playback by Time
The
indicates the start/end time of the record.
Table 6. 2 Detailed Explanation of Playback-by-time Interface
Button
/
Operation
Audio on/
Button
/
Mute
tag
Pause reverse
Single-frame
reverse play
Start/Stop
/
Operation
30s forward
Add
Tag
customized tag
management
Pause play/
play/
/
Button
clipping
Add default
Reverse play/
Operation
Button
Operation
30s reverse
Speed down
Scaling
Play/
/
Single-frame
up/down the
Speed up
time line
play
Previous day
Next day
Full Screen
Exit
Stop
Digital Zoom
Smart Search
Video type
Process bar
67
User Manual of INVR-0xA / INVR-0xPOE series NVR
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
6.1.3 Playing Back by Event Search
Purpose:
Play back record files on one or several channels searched out by restricting event type (e.g. alarm input and
motion detection).
Steps:
1. Enter the Playback interface.
Menu>Playback
2. Select the Event in the drop-down list on the top-left side.
3. Select Motion as the event type, edit the Start time and End time.
Figure 6. 8 Motion Search Interface
4. Click Search button to get the search result information. You may refer to the right-side bar for the result.
68
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 6. 9 Motion Search Result Bar
5. Click
button to play back the file.
 Pre-play and post-play can be configured.
 If the event is set to trigger the recording of multiple channels, clicking the
will pop up the
Synch Playback interface. You can select the channels to play back synchronously.
You can click the Back button to back to the search interface.
6. Playback interface.
The toolbar in the bottom part of Playback interface can be used to control playing process.
Figure 6. 10 Interface of Playback by Event
Figure 6. 11 Toolbar of Playback by Event
69
User Manual of INVR-0xA / INVR-0xPOE series NVR
Table 6. 3 Detailed Explanation of Playback-by-event Toolbar
Button
Operation
/
Button
Audio on/
/
Mute
tag
Pause reverse
Start/Stop
/
Single-frame
reverse play
Operation
30s forward
Add
Tag
customized tag
management
Pause play/
play/
Reverse play/
Button
clipping
Add default
/
Operation
Button
Operation
30s reverse
Speed down
Scaling
Play/
/
Single-frame
up/down the
Speed up
time line
play
Previous day
Next day
Full Screen
Exit
Stop
Digital Zoom
Smart Search
Video type
Process bar
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
6.1.4 Playing Back by Tag
Purpose:
Video tag allows you to record related information like people and location of a certain time point during playback.
You are also allowed to use video tag(s) to search for record files and position time point.
Before playing back by tag:
1. Enter Playback interface.
Menu>Playback
2. Search and play back the record file(s). Refer to Chapter 6.1.1 for the detailed information about searching
and playback of the record files.
70
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 6. 12 Interface of Playback by Time
Click
button to add default tag.
Click
button to add customized tag and input tag name.
Max. 64 tags can be added to a single video file.
3. Tag management.
Click
button to check, edit and delete tag(s).
Figure 6. 13 Tag Management Interface
Steps:
1. Select the Tag from the drop-down list in the Playback interface.
2. Choose channels, edit start time and end time, and then click Search to enter Search Result interface.
71
User Manual of INVR-0xA / INVR-0xPOE series NVR
You can enter keyword in the textbox
to search the tag on your command.
Figure 6. 14 Video Search by Tag
3. Click
button to play back the file.
You can click the Back button to back to the search interface.
Pre-play and post-play can be configured.
Figure 6. 15 Interface of Playback by Tag
Figure 6. 16 Toolbar of Playback by Tag
72
User Manual of INVR-0xA / INVR-0xPOE series NVR
Table 6. 4 Detailed Explanation of Playback-by-tag Toolbar
Button
Operation
/
Audio on/
Button
/
Operation
Start/Stop
Mute
tag
Pause reverse
Reverse play/
Add
Tag
customized tag
management
Pause play/
play/
/
Single-frame
Operation
30s reverse
Speed down
up/down the
Speed up
time line
play
reverse play
Button
Scaling
Play/
/
Single-frame
Operation
30s forward
clipping
Add default
/
Button
Previous day
Next day
Full Screen
Exit
Stop
Digital Zoom
Smart Search
Video type
Process bar
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
6.1.5 Playing Back by System Logs
Purpose:
Play back record file(s) associated with channels after searching system logs.
Steps:
1. Enter Log Information interface.
Menu>Maintenance>Log Information
2. Click Log Search tab to enter Playback by System Logs.
Set search time and type and click Search button.
73
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 6. 17 System Log Search Interface
3. Choose a log with record file and click
button to enter Playback interface.
If there is no record file at the time point of the log, the message box “No result found” will pop up.
Figure 6. 18 Result of System Log Search
4. Playback interface.
The toolbar in the bottom part of Playback interface can be used to control playing process.
74
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 6. 19 Interface of Playback by Log
6.1.6 Playing Back External File
Purpose:
Perform the following steps to look up and play back files in the external devices.
Steps:
1. Enter Tag Search interface.
Menu>Playback
2. Select the External File in the drop-down list on the top-left side.
The files are listed in the right-side list.
You can click the Refresh button to refresh the file list.
3. Select and click the
button to play back it.
Figure 6. 20 Interface of External File Playback
75
User Manual of INVR-0xA / INVR-0xPOE series NVR
6.2 Auxiliary Functions of Playback
6.2.1 Playing Back Frame by Frame
Purpose:
Play video files frame by frame, in case of checking image details of the video when abnormal events happen.
Steps:
Go to Playback interface.
If you choose playback of the record file: click button
on the playback screen represents playback of one frame.
until the speed changes to Single frame and one click
If you choose reverse playback of the record file: click button
until the speed changes to Single frame and
one click on the playback screen represents adverse playback of one frame. It is also feasible to use button
in
toolbar.
6.2.2 Smart Search
Purpose:
In order to locate motion detection event easily and accurately in the playback progress bar, you are allowed to
analyze a certain area (scene) dynamically, and to get all of the related motion detection events that occurred in
this area.
The smart search function varies according to the camera connected to the NVR.
Before you start:
1. Log in the network camera by the web browser, and enable the Dynamic Analysis for Motion by checking
the checkbox of it. You may enter the motion detection configuration interface by Configuration> Advanced
Configuration> Events> Motion Detection.
2. Enable the motion detection function and set the arming area to the full screen in the NVR local menu.
Please refer to chapter 5.3 for details.
Steps:
1. Enter the Playback interface and play a record file. Refer to Chapter 6.1.1 for the detailed information about
searching and playback of the record files.
76
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 6. 21 Interface of Playback by Time
2. Click the
on the playback control toolbar to enter Smart Search mode.
3. Click and drag the mouse to draw area(s). You can click button
area. After drawing area(s), click button
to set the full screen as target searching
to execute smart search in this area.
Multi-area and full-screen searching modes are supported.
Figure 6. 22 Draw Area of Smart Search
The results of smart search will be marked as
in the progress bar.
The hidden list of record files display when moving the mouse to the right of the playback interface.
77
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 6. 23 Smart Search Result
Figure 6. 24 Toolbar of Smart Search Playback
The
indicates the start/end time of the record.
Table 6. 5 Detailed Explanation of Smart-search-playback Toolbar
Button
/
Operation
Audio on/
Button
/
Mute
tag
Pause reverse
Single-frame
reverse play
Start/Stop
/
Operation
30s forward
Add
Tag
customized tag
management
Pause play/
play/
Reverse play/
Button
clipping
Add default
/
Operation
Button
Operation
30s reverse
Speed down
Scaling
Play/
/
Single-frame
up/down the
Speed up
time line
play
Previous day
Next day
Full Screen
Exit
Stop
Digital Zoom
Smart Search
Video type
Process bar
Smart search
result
78
User Manual of INVR-0xA / INVR-0xPOE series NVR
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
6.2.3 Digital Zoom
Steps:
1. Click the
button on the playback control bar to enter Digital Zoom interface.
2. Use the mouse to draw a red rectangle and the image within it will be enlarged up to 16 times.
Figure 6. 25 Draw Area for Digital Zoom
3. Right-click the image to exit the digital zoom interface.
6.2.4 Reverse Playback of Multi-channel
Purpose:
You can play back record files of multi-channel reversely. Up to 8-ch (with 4CIF resolution) simultaneous adverse
playback is supported; up to 4-ch (with 720P resolution) simultaneous adverse playback is supported, up to 2-ch
(with 1080P resolution) and up to 1-ch (with 5MP resolution) reverse playback is supported.
Steps:
1. Enter Playback interface.
Menu>Playback
2. Check more than one checkboxes to select multiple channels and click to select a date on the calendar.
79
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 6. 26 4-ch Synchronous Playback Interface
3. Click
to play back the record files reversely.
80
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 7 Backup
81
User Manual of INVR-0xA / INVR-0xPOE series NVR
7.1 Backing up Record Files
7.1.1 Backing up by Normal Video Search
Purpose:
The record files can be backup to various devices, such as USB devices (USB flash drives, USB HDDs, USB
writer), and SATA writer.
Backup using USB flash drives and USB HDDs
Steps:
1. Enter Export interface.
Menu>Export>Normal
2. Set search condition and click Search button to enter the search result interface.
Figure 7. 1 Normal Video Search for Backup
3. Select record files you want to back up, and click the Export button.
Click
to play the record file if you want to check it.
Check the checkbox before the record files you want to back up.
The size of the currently selected files is displayed in the lower-left corner of the window.
Figure 7. 2 Result of Normal Video Search for Backup
4. Click Export button in the pop-up USB device management interface.
82
User Manual of INVR-0xA / INVR-0xPOE series NVR
If the inserted USB device is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
You can also format USB flash drives or USB HDDs via the device.
Figure 7. 3 Export by Normal Video Search using USB Flash Drive
5. Select the file type in the by clicking the icon of corresponding option and click the OK button to start
backup.
Figure 7. 4 Export Options
Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”.
83
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 7. 5 Export Finished
6. Check backup result.
Choose the record file in Export interface and click button
to check it.
Backup using USB writer and SATA writer
Steps:
1. Enter Export interface.
Menu>Export>Normal
2. Set search condition and click Search button to enter the search result interface.
Figure 7. 6 Normal Video Search for Backup
3. Select record files you want to back up, and click the Export button.
Click button
to play the record file if you want to check it.
Check the checkbox before the record files you want to back up.
The size of the currently selected files is displayed in the lower-left corner of the window.
84
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 7. 7 Result of Normal Video Search for Backup
4. Click Export button in the pop-up USB device management interface.
If the inserted USB writer or SATA writer is not recognized:
•
•
•
Click the Refresh button.
Reconnect device.
Check for compatibility from vendor.
Figure 7. 8 Export by Normal Video Search using USB Writer
5. Select the file type in the by clicking the icon of corresponding option and click the OK button to start
backup.
85
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 7. 9 Export Options
Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”.
Figure 7. 10 Export Finished
6. Check backup result.
Choose the record file in Export interface and click button
to check it.
7.1.2 Backing up by Event Search
Purpose:
Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), or SATA
writer. Quick Backup and Normal Backup are supported.
Steps:
1. Enter Export interface.
Menu>Export>Event
1)
Select “Motion” from the dropdown list of Event Type.
Event types contain Alarm Input and Motion, here we take the backing up by motion as an example.
2)
Select the camera No. and time.
Figure 7. 11 Event Search for Backup
86
User Manual of INVR-0xA / INVR-0xPOE series NVR
2. Click Search button to enter the Search Result interface.
Figure 7. 12 Result of Event Search
3. Select record files to export.
1)
Clicking Quick Export button will export record files of all channels triggered by the selected alarm
input.
2)
Clicking Details button will take you to the interface with detailed information of all channels
triggered by the selected alarm input.
Figure 7. 13 Event Details Interface
4. Click Export button in the pop-up USB device management interface.
If the inserted USB device is not recognized:
•
•
•
Click the Refresh button.
Reconnect device.
Check for compatibility from vendor.
87
User Manual of INVR-0xA / INVR-0xPOE series NVR
You can also format USB flash drives or USB HDDs via the device.
Figure 7. 14 Export by Normal Video Search using USB Flash Drive
5. Select the file type in the by clicking the icon of corresponding option and click the OK button to start
backup.
Figure 7. 15 Export Options
Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”.
Figure 7. 16 Export Finished
6. Check backup result.
Choose the record file in Export interface and click button
88
to check it.
User Manual of INVR-0xA / INVR-0xPOE series NVR
7.1.3 Backing up Video Clips
Purpose:
You may also select video clips to export directly during Playback, using USB devices (USB flash drives, USB
HDDs, USB writer) or SATA writer.
Steps:
1. Enter Playback interface.
Please refer to Chapter 6.1 Playing Back Record Files.
2. During playback, use buttons
and
in the playback toolbar to start or stop clipping record file(s).
3. Quit Playback interface after finishing clipping and you will then be prompted to save the clips.
A maximum of 30 clips can be selected for each channel.
Figure 7. 17 Interface of Playback by Time
4. Click Yes to save video clips and enter Export interface, or click No to quit and do not save video clips.
Figure 7. 18 Attention to Video Clip Saving
5. Click Export button in the pop-up USB device management interface.
If the inserted USB device is not recognized:
•
•
•
Click the Refresh button.
Reconnect device.
Check for compatibility from vendor.
89
User Manual of INVR-0xA / INVR-0xPOE series NVR
You can also format USB flash drive or USB HDDs via the device.
Figure 7. 19 Export Video Clips Using USB Flash Drive
6. Select the file type in the by clicking the icon of corresponding option and click the OK button to start
backup.
Figure 7. 20 Export Options
Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”.
Figure 7. 21 Export Finished
7. Check backup result.
Choose the record file in Export interface and click button
90
to check it.
User Manual of INVR-0xA / INVR-0xPOE series NVR
7.2 Managing Backup Devices
Management of USB flash drives and USB HDDs.
1.
Enter Search Result interface of record files.
Menu>Export>Normal
Set search condition and click Search button to enter Search Result interface.
At least one camera shall be selected.
Figure 7. 22 Normal Video Search for Backup
2.
Select record files you want to back up.
Click Export button to enter Export interface.
At least one record file shall be selected.
Figure 7. 23 Result of Normal Video Search for Backup
3.
Backup device management.
Click New Folder button if you want to create a new folder in the backup device.
Select a record file or folder in the backup device and click
Select a record file in the backup device and click
Click Format button to format the backup device.
91
button if you want to delete it.
button to play it.
User Manual of INVR-0xA / INVR-0xPOE series NVR
If the inserted USB device is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
Figure 7. 24 USB Flash Drive Management
Management of USB writers or DVD-R/W
1.
Enter Search Result interface of record files.
Menu>Export>Normal
Set search condition and click Search button to enter Search Result interface.
At least one channel shall be selected.
Figure 7. 25 Normal Video Search for Backup
2.
Select record files you want to back up.
Click Export button to enter Export interface.
At least one record file shall be selected.
92
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 7. 26 Result of Normal Video Search for Backup
3.
Backup device management.
Click Erase button if you want to erase the files from a re-writable CD/DVD.
There must be a re-writable CD/DVD when you make this operation.
If the inserted USB writer or DVD-R/W is not recognized:
•
•
•
Click the Refresh button.
Reconnect device.
Check for compatibility from vendor.
Figure 7. 27 USB Writer Management
93
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 8 Alarm Settings
94
User Manual of INVR-0xA / INVR-0xPOE series NVR
8.1 Setting Motion Detection Alarm
Steps:
1. Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion
detection.
Menu> Camera> Motion
Figure 8. 1 Motion Detection Setup Interface
2. Set up detection area and sensitivity.
Check “Enable Motion Detection” checkbox, use the mouse to draw detection area(s) and drag the sensitivity
bar to set sensitivity.
Click
button to set alarm response actions.
3. Click Trigger Channel tab and select one or more channels which will start to record or become full-screen
monitoring when motion alarm is triggered, and click Apply to save the settings.
Figure 8. 2 Set Trigger Camera of Motion Detection
4. Set up arming schedule of the channel.
1) Select Arming Schedule tab to set the arming schedule of handling actions for the motion detection.
2) Choose one day of a week and up to eight time periods can be set within each day.
3) Click Apply to save the settings
95
User Manual of INVR-0xA / INVR-0xPOE series NVR
Time periods shall not be repeated or overlapped.
Figure 8. 3 Set Arming Schedule of Motion Detection
5. Click Linkage Action tab to set up alarm response actions of motion alarm (please refer to Chapter Fehler!
Verweisquelle konnte nicht gefunden werden.).
Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to
copy an arming schedule to other days.
6. Click the OK button to complete the motion detection settings of the channel.
96
User Manual of INVR-0xA / INVR-0xPOE series NVR
8.2 Detecting Video Loss Alarm
Purpose:
Detect video loss of a channel and take alarm response action(s).
Steps:
1. Enter Video Loss interface of Camera Management and select a channel you want to detect.
Menu> Camera> Video Loss
Figure 8. 4 Video Loss Setup Interface
2. Set up handling method of video loss.
Check the checkbox of “Enable Video Loss Alarm”, and click
button to set up handling action of video
loss.
3. Set up arming schedule of the channel.
1)
Select Arming Schedule tab to set the channel’s arming schedule.
2)
Choose one day of a week and up to eight time periods can be set within each day.
3)
Click Apply button to save the settings.
Time periods shall not be repeated or overlapped.
97
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 8. 5 Set Arming Schedule of Video Loss
4. Select Linkage Action tab to set up alarm response action of video loss (please refer to Chapter Fehler!
Verweisquelle konnte nicht gefunden werden.).
Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to
copy an arming schedule to other days.
5. Click the OK button to complete the video loss settings of the channel.
98
User Manual of INVR-0xA / INVR-0xPOE series NVR
8.3 Detecting Video Tampering Alarm
Purpose:
Trigger alarm when the lens is covered and take alarm response action(s).
Steps:
1. Enter Video Tampering interface of Camera Management and select a channel you want to detect video
tampering.
Menu> Camera> Video Tampering Detection
Figure 8. 6 Video Tampering Setup Interface
2. Set the video tampering handling method of the channel.
Check the checkbox of “Enable Video Tampering”.
Drag the sensitivity bar and choose a proper sensitivity level. Use the mouse to draw an area you want to
detect video tampering.
Click
button to set up handling method of video tampering.
Figure 8. 7 Set Detection Area and Sensitivity of Video Tampering
3. Set arming schedule and alarm response actions of the channel.
1) Click Arming Schedule tab to set the channel’s arming schedule.
2) Choose one day of a week and Max. eight time periods can be set within each day.
3) Click Apply button to save the settings.
99
User Manual of INVR-0xA / INVR-0xPOE series NVR
Time periods shall not be repeated or overlapped.
Figure 8. 8 Set Arming Schedule of Video Tampering
4. Select Linkage Action tab to set alarm response actions of video tampering alarm (please refer to Chapter
Fehler! Verweisquelle konnte nicht gefunden werden.).
Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to
copy an arming schedule to other days.
5. Click the OK button to complete the video tampering settings of the channel.
100
User Manual of INVR-0xA / INVR-0xPOE series NVR
8.4 Handling Exceptions Alarm
Purpose:
Exception settings refer to the handling method of various exceptions, e.g.
•
•
•
•
•
•
HDD Full: The HDD is full.
HDD Error: Writing HDD error or unformatted HDD.
Network Disconnected: Disconnected network cable.
IP Conflicted: Duplicated IP address.
Illegal Login: Incorrect user ID or password.
Record Exception: No space for saving recorded files.
Steps:
1. Enter Exception interface of System Configuration and handle various exceptions.
Menu> Configuration> Exceptions
2. Select the exception type in the drop-down list and configure the corresponding response action.
You can select All as the exception type and the configured response action will be applied to all the
exceptions.
Please refer to Chapter Fehler! Verweisquelle konnte nicht gefunden werden. for detailed alarm response
actions.
Figure 8. 9 Exceptions Setup Interface
101
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 9 Network Settings
102
User Manual of INVR-0xA / INVR-0xPOE series NVR
9.1 Configuring General Settings
Purpose:
Network settings must be properly configured before you operate NVR over network.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration>Network
2. Select the General tab.
INVR-0xA
INVR-0xPOE
Figure 9. 1 Network Settings Interface
3. In the General Settings interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4
Gateway, MTU and DNS Server.
If the DHCP server is available, you can click the checkbox of DHCP to automatically obtain an IP address
and other network settings from that server.
 The valid value range of MTU is 500 ~ 9676.
 For the PoE NVR, you need to configure the internal NIC address, so that IP addresses are assigned to
the cameras connected to the PoE or built-in switch interfaces.
4. After having configured the general settings, click Apply to save the settings.
103
User Manual of INVR-0xA / INVR-0xPOE series NVR
9.2 Configuring Advanced Settings
9.2.1 Configuring PPPoE Settings
Purpose:
Your NVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE).
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the PPPoE tab to enter the PPPoE Settings interface, as shown in Figure 9. 2.
Figure 9. 2 PPPoE Settings Interface
3. Check the PPPoE checkbox to enable this feature.
4. Enter User Name, Password, and Confirm Password for PPPoE access.
The User Name and Password should be assigned by your ISP.
5. Click Apply to save and exit the interface.
6. After successful settings, the system asks you to reboot the device to enable the new settings, and the PPPoE
dial-up is automatically connected after reboot.
You can go to Menu >Maintenance>System Info >Network interface to view the status of PPPoE connection.
Please refer to Chapter Viewing System Information for PPPoE status.
9.2.2 Configuring DDNS
Purpose:
If your NVR is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to be used
for network access.
Prior registration with your ISP is required before configuring the system to use DDNS.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the DDNS tab to enter the DDNS Settings interface.
3. Check the DDNS checkbox to enable this feature.
4. Select DDNS Type. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull, NO-IP and
HiDDNS.
• IPServer: Enter Server Address for IPServer.
104
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 9. 3 IPServer Settings Interface
• DynDNS:
1) Enter Server Address for DynDNS (i.e. members.dyndns.org).
2) In the NVR Domain Name text field, enter the domain obtained from the DynDNS website.
3) Enter the User Name and Password registered in the DynDNS website.
Figure 9. 4 DynDNS Settings Interface
• PeanutHull: Enter the User Name and Password obtained from the PeanutHull website.
Figure 9. 5 PeanutHull Settings Interface
• NO-IP:
Enter the account information in the corresponding fields. Refer to the DynDNS settings.
1) Enter Server Address for NO-IP.
2) In the NVR Domain Name text field, enter the domain obtained from the NO-IP website
(www.no-ip.com).
3) Enter the User Name and Password registered in the NO-IP website.
Figure 9. 6 NO-IP Settings Interface
• HiDDNS:
105
User Manual of INVR-0xA / INVR-0xPOE series NVR
Enter the Server Address and Device Domain Name for HiDDNS.
1) Enter the Server Address of the HiDDNS server, which is www.hiddns.com by default.
2) Enter the Device Domain Name. You can use the alias you registered in the HiDDNS server or
define a new device domain name. If a new alias of the device domain name is defined in the NVR, it
will replace the old one registered on the server. You can register the alias of the device domain name
in the HiDDNS server first and then enter the alias to the Device Domain Name in the NVR; you
can also enter the domain name directly on the NVR to create a new one.
Figure 9. 7 HiDDNS Settings Interface
Register the device on the HiDDNS server.
1)
Go to the HiDDNS website: www.hiddns.com.
2)
Click
to register an account if you do not have one and use the account to log in.
Figure 9. 8 Register an Account
3)
In the Device Management interface, click
to register the device.
Figure 9. 9 Register the Device
The device name can only contain the lower-case English letter, numeric and ‘-’; and it must start
106
User Manual of INVR-0xA / INVR-0xPOE series NVR
with the lower-case English letter and cannot end with ‘-’.
Access the Device via Web Browser or Client Software
After having successfully registered the device on the HiDDNS server, you can access your device via
web browser or Client Software with the Device Domain Name (Device Name).
Task 1: Access the Device via Web Browser
Open a web browser, and enter http://www.hiddns.com/alias in the address bar. Alias refers to the Device
Domain Name on the device or the Device Name on the HiDDNS server.
Example: http://www.hiddns.com/nvr
If you mapped the HTTP port on your router and changed it to port No. except 80, you have to
enter http://www.hiddns.com/alias:HTTP port in the address bar to access the device. You can
refer to Chapter 9.2.10 for the mapped HTTP port No.
Task 2: Access the devices via VMS-A1
For VMS-A1, in the Add Device window, select
and then edit the device information.
Nickname: Edit a name for the device as you want.
Server Address: www.hiddns.com
Device Domain Name: It refers to the Device Domain Name on the device or the Device Name on the
HiDDNS server you created.
User Name: Enter the user name of the device. By default it is admin.
Password: Enter the password of the device. By default it is 12345.
Figure 9. 10 Access Device via VMS-A1
5. Click Apply button to save and exit the interface.
9.2.3 Configuring NTP Server
Purpose:
A Network Time Protocol (NTP) Server can be configured on your NVR to ensure the accuracy of system
date/time.
107
User Manual of INVR-0xA / INVR-0xPOE series NVR
Steps:
1.
Enter the Network Settings interface.
Menu >Configuration> Network
2.
Select the NTP tab to enter the NTP Settings interface, as shown in Figure 9. 11.
Figure 9. 11 NTP Settings Interface
3.
Check the Enable NTP checkbox to enable this feature.
4.
Configure the following NTP settings:
• Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute.
• NTP Server: IP address of NTP server, which can be your PC or server provides the timing service.
• NTP Port: Port of NTP server.
5.
Click Apply button to save and exit the interface.
The time synchronization interval can be set from1 to 10080min, and the default value is 60min. If the
NVR is connected to a public network, you should use a NTP server that has a time synchronization
function, such as the server at the National Time Center (IP Address: 210.72.145.44). If the NVR is setup
in a more customized network, NTP software can be used to establish a NTP server used for time
synchronization.
9.2.4 Configuring SNMP
Purpose:
You can use SNMP protocol to get device status and parameters related information.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the SNMP tab to enter the SNMP Settings interface, as shown in Figure 9. 12.
Figure 9. 12 SNMP Settings Interface
3. Check the SNMP checkbox to enable this feature.
4. Configure the following SNMP settings:
• Trap Address: IP Address of SNMP host.
• Trap Port: Port of SNMP host.
5. Click Apply button to save and exit the interface.
108
User Manual of INVR-0xA / INVR-0xPOE series NVR
Before setting the SNMP, please download the SNMP software and manage to receive the device
information via SNMP port. By setting the Trap Address, the NVR is allowed to send the alarm event and
exception message to the surveillance center.
9.2.5 Configuring Remote Alarm Host
Purpose:
With a remote alarm host configured, the NVR will send the alarm event or exception message to the host when an
alarm is triggered. The remote alarm host must have the Network Video Surveillance software installed.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 9. 13.
Figure 9. 13 More Settings Interface
3. Enter Alarm Host IP and Alarm Host Port in the text fields.
The Alarm Host IP refers to the IP address of the remote PC on which the Network Video Surveillance
Software (e.g., VMS) is installed, and the Alarm Host Port must be the same as the alarm monitoring port
configured in the software.
Figure 9. 14 Configure Alarm Host
4. Click Apply button to save and exit the interface.
9.2.6 Configuring Multicast
Purpose:
The multicast can be configured to realize live view for more than 64 cameras through network for INVR-0xA
series NVR.
A multicast address spans the Class-D IP range of 224.0.0.0 to239.255.255.255. It is recommended to use the IP
address ranging from 239.252.0.0 to 239.255.255.255.
109
User Manual of INVR-0xA / INVR-0xPOE series NVR
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 9. 13.
3. Set Multicast IP, as shown in Figure 9. 15. When adding a device to the Network Video Surveillance
Software, the multicast address must be the same as the NVR’s multicast IP.
Figure 9. 15 Configure Multicast
4. Click Apply button to save and exit the interface.
The multicast function should be supported by the network switch to which the NVR is connected.
9.2.7 Configuring RTSP
Purpose:
The RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and
communications systems to control streaming media servers.
Steps:
1. Enter the Network Settings menu
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings menu, as shown in Figure 9. 13.
Figure 9. 16 RTSP Settings Interface
3. Enter the RTSP port in the text field of RTSP Service Port. The default RTSP port is 554, and you can
change it according to different requirements.
4. Click Apply button to save and exit the menu.
9.2.8 Configuring Server and HTTP Ports
Purpose:
You can change the server and HTTP ports in the Network Settings menu. The default server port is 8000 and the
default HTTP port is 80.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 9. 13.
3. Enter new Server Port and HTTP Port.
110
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 9. 17 Host/Others Settings Menu
4. Enter the Server Port and HTTP Port in the text fields. The default Server Port is 8000 and the HTTP Port is
80, and you can change them according to different requirements.
5. Click Apply button to save and exit the interface.
The Server Port should be set to the range of 2000-65535 and it is used for remote client software access.
The HTTP port is used for remote web browser access.
9.2.9 Configuring HTTPS Port
Purpose:
HTTPS provides authentication of the web site and associated web server that one is communicating with, which
protects against Man-in-the-middle attacks. Perform the following steps to set the port number of https.
Example:
If you set the port number as 443 and the IP address is 192.0.0.64, you may access the device by inputting
https://192.0.0.64:443 via the web browser.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 9. 13.
3. Check the checkbox of Enable HTTPS.
Figure 9. 18 HTTPS Settings Menu
4. Enter the HTTPS Port.
5. Click the Apply button to save and exit the interface.
9.2.10 Configuring Email
Purpose:
The system can be configured to send an Email notification to all designated users if an alarm event is detected,
etc., an alarm or motion event is detected or the administrator password is changed.
Before configuring the Email settings, the NVR must be connected to a local area network (LAN) that maintains
an SMTP mail server. The network must also be connected to either an intranet or the Internet depending on the
location of the e-mail accounts to which you want to send notification.
Steps:
1.
Enter the Network Settings interface.
Menu >Configuration> Network
111
User Manual of INVR-0xA / INVR-0xPOE series NVR
2.
Set the IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway and the Preferred DNS Server in the Network
Settings menu.
3.
Click Apply button to save the settings.
2.
Select the Email tab to enter the Email Settings interface.
Figure 9. 19 Email Settings Interface
3.
Configure the following Email settings:
Enable Server Authentication (optional): Check the checkbox to enable the server authentication feature.
User Name: The user account of sender’s Email for SMTP server authentication.
Password: The password of sender’s Email for SMTP server authentication.
SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com).
SMTP Port No.: The SMTP port. The default TCP/IP port used for SMTP is 25.
Enable SSL (optional): Check the checkbox to enable SSL if required by the SMTP server.
Sender: The name of sender.
Sender’s Address: The Email address of sender.
Select Receivers: Select the receiver. Up to 3 receivers can be configured.
Receiver: The name of user to be notified.
Receiver’s Address: The Email address of user to be notified.
Enable Attached Pictures: Check the checkbox if you want to send email with attached alarm images. The
interval is the time of two adjacent alarm images. You can also set SMTP port and enable SSL here.
Interval: The interval refers to the time between two actions of sending attached pictures.
4.
Click Apply button to save the Email settings.
5.
You can click Test button to test whether the Email settings work. The corresponding Attention message box
will pop up.
Figure 9. 20 Email Testing Attention
112
User Manual of INVR-0xA / INVR-0xPOE series NVR
9.2.11 Configuring UPnP™
Purpose:
Universal Plug and Play (UPnP™) can permit the device seamlessly discover the presence of other network
devices on the network and establish functional network services for data sharing, communications, etc. You can
use the UPnP™ function to enable the fast connection of the device to the WAN via a router without port mapping.
Before you start:
If you want to enable the UPnP™ function of the device, you must enable the UPnP™ function of the router to
which your device is connected. When the network working mode of the device is set as multi-address, the Default
Route of the device should be in the same network segment as that of the LAN IP address of the router.
Steps:
1. Enter the Network Settings interface.
Menu > Configuration > Network
2. Select the UPnP tab to enter the UPnP™ interface.
Figure 9. 21 UPnP™ Settings Interface
3. Check
checkbox to enable UPnP™.
4. Select the Mapping Type as Manual or Auto in the drop-down list.
Task1: Auto
If you select Auto, the Port Mapping items are read-only, and the external ports are set by the router
automatically.
Steps:
1)
Click Apply button to save the settings.
2)
You can click Refresh button to get the latest status of the port mapping.
Figure 9. 22 UPnP™ Settings Finished-Auto
Task2: Manual
If you select Manual as the mapping type, you can edit the external port on your demand by clicking
activate the External Port Settings dialog box.
to
Steps:
1)
Click
to activate the External Port Settings dialog box. Configure the external port No. for server
port, http port, RTSP port and https port respectively.
113
User Manual of INVR-0xA / INVR-0xPOE series NVR
 You can use the default port No., or change it according to actual requirements.
 External Port indicates the port No. for port mapping in the router.
 The value of the RTSP port No. should be 554 or between 1024 and 65535, while the value of the
other ports should be between 1 and 65535 and the value must be different from each other. If
multiple devices are configured for the UPnP™ settings under the same router, the value of the
port No. for each device should be unique.
Figure 9. 23 External Port Settings Dialog Box
2)
Click Apply button to save the settings.
3)
You can click Refresh button to get the latest status of the port mapping.
Figure 9. 24 UPnP™ Settings Finished-Manual
9.2.12 Configuring High-speed Download
Purpose:
You can enable the High-speed Download function to widen the outgoing bandwidth of the device. In this way you
can speed up the download of record files through web browser or CMS software.
If you enable the high-speed download function, the local menu operation will be affected. It is
recommended to disable this function after finishing the remote downloading of record files.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 9. 13.
114
User Manual of INVR-0xA / INVR-0xPOE series NVR
3. Check the checkbox of Enable High-speed Download. And click the OK button in the pop-up message box
to confirm the settings.
Figure 9. 25 High-speed Download Settings Menu
Figure 9. 26 Message Box of High-speed Download
4. Click Apply button to save and exit the interface.
115
User Manual of INVR-0xA / INVR-0xPOE series NVR
9.3 Checking Network Traffic
Purpose:
You can check the network traffic to obtain real-time information of NVR such as linking status, MTU,
sending/receiving rate, etc.
Steps:
1. Enter the Network Traffic interface.
Menu >Maintenance>Net Detect
Figure 9. 27 Network Traffic Interface
2. You can view the sending rate and receiving rate information on the interface. The traffic data is refreshed
every 1 second.
116
User Manual of INVR-0xA / INVR-0xPOE series NVR
9.4 Configuring Network Detection
Purpose:
You can obtain network connecting status of NVR through the network detection function, including network delay,
packet loss, etc.
9.4.1 Testing Network Delay and Packet Loss
Steps:
1.
Enter the Network Traffic interface.
Menu >Maintenance>Net Detect
2.
Click the Network Detection tab to enter the Network Detection menu, as shown in Figure 9. 28.
Figure 9. 28 Network Detection Interface
3.
Enter the destination address in the text field of Destination Address.
4.
Click Test to start testing network delay and packet loss. The testing result pops up on the window. If the
testing is failed, the error message box will pop up as well. Refer to Figure 9. 29.
Figure 9. 29 Testing Result of Network Delay and Packet Loss
9.4.2 Exporting Network Packet
Purpose:
By connecting the NVR to network, the captured network data packet can be exported to USB-flash disk and other
local backup devices.
Steps:
1. Enter the Network Traffic interface.
Menu >Maintenance>Net Detect
2. Click the Network Detection tab to enter the Network Detection interface.
3. Select the backup device from the dropdown list of Device Name, as shown in Figure 9. 30.
117
User Manual of INVR-0xA / INVR-0xPOE series NVR
Click Refresh button if the connected local backup device cannot be displayed. When it fails to detect
the backup device, please check whether it is compatible with the NVR. You can format the backup
device if the format is incorrect.
Figure 9. 30 Export Network Packet
4. Click Export to start exporting.
5. After the exporting is complete, click OK to finish the packet export.
Figure 9. 31 Packet Export Attention
Up to 1M data can be exported each time.
9.4.3 Checking the Network Status
Purpose:
You can also check the network status and quick set the network parameters in this interface.
Steps:
1. Enter the Network Traffic interface.
Menu >Maintenance>Net Detect
2. Click the Network Detection tab to enter the Network Detection interface.
3. Click Status button on the right bottom of the page.
118
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 9. 32 Network status checking
If the network is normal the following message box pops out.
Figure 9. 33 Network status checking result
If the message box pops out with other information instead of this one, you can click Network button to
show the quick setting interface of the network parameters.
9.4.4 Checking Network Statistics
Purpose:
You can check the network status to obtain the real-time information of NVR.
Steps:
1. Enter the Network Detection interface.
Menu>Maintenance>Net Detection
2. Choose the Network Stat. tab.
Figure 9. 34 Network Stat. Interface
3. Check the bandwidth of IP Camera, bandwidth of Remote Live View, bandwidth of Remote Playback,
bandwidth of Net Receive Idle and bandwidth of Net Send Idle.
4. You can click Refresh button to get the newest status.
119
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 10 HDD Management
120
User Manual of INVR-0xA / INVR-0xPOE series NVR
10.1 Initializing HDDs
Purpose:
A newly installed hard disk drive (HDD) must be initialized before it can be used with your NVR.
A message box pops up when the NVR starts up if there exits any uninitialized HDD.
Figure 10. 1 Message Box of Uninitialized HDD
Click Yes button to initialize it immediately or you can perform the following steps to initialize the HDD.
Steps:
1. Enter the HDD Information interface.
Menu > HDD> General
Figure 10. 2 HDD Information Interface
2. Select HDD to be initialized.
3. Click the Init button.
Figure 10. 3 Confirm Initialization
4. Select the OK button to start initialization.
Figure 10. 4 Status changes to Formatting
121
User Manual of INVR-0xA / INVR-0xPOE series NVR
5. After the HDD has been initialized, the status of the HDD will change from Uninitialized to Normal.
Figure 10. 5 HDD Status Changes to Normal
Initializing the HDD will erase all data on it.
122
User Manual of INVR-0xA / INVR-0xPOE series NVR
10.2 Managing Network HDD
Purpose:
You can add the allocated NAS or disk of IP SAN to NVR, and use it as network HDD.
Steps:
1. Enter the HDD Information interface.
Menu > HDD>General
2. Click the Add button to enter the Add NetHDD interface, as shown in Figure 10. 6.
Figure 10. 6 HDD Information Interface
3. Add the allocated NetHDD.
4. Select the type to NAS or IP SAN.
5. Configure the NAS or IP SAN settings.
• Add NAS disk:
1) Enter the NetHDD IP address in the text field.
2) Click the Search button to search the available NAS disks.
3) Select the NAS disk from the list shown below.
Or you can just manually enter the directory in the text field of NetHDD Directory.
4) Click the OK button to add the configured NAS disk.
Up to 8 NAS disks can be added.
123
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 10. 7 Add NAS Disk
• Add IP SAN:
1) Enter the NetHDD IP address in the text field.
2) Click the Search button to search the available IP SAN disks.
3) Select the IP SAN disk from the list shown below.
4) Click the OK button to add the selected IP SAN disk.
Up to 1 IP SAN disk can be added.
Figure 10. 8 Add IP SAN Disk
6.
After having successfully added the NAS or IP SAN disk, return to the HDD Information menu. The added
NetHDD will be displayed in the list.
If the added NetHDD is uninitialized, please select it and click the Init button for initialization.
Figure 10. 9 Initialize Added NetHDD
124
User Manual of INVR-0xA / INVR-0xPOE series NVR
10.3 Managing HDD Group
10.3.1 Setting HDD Groups
Purpose:
Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD
group through HDD settings.
Steps:
1. Enter the Storage Mode interface.
Menu > HDD > Advanced
2. Set the Mode to Group, as shown in Figure 10. 10.
Figure 10. 10 Storage Mode Interface
3. Click the Apply button and the following Attention box will pop up.
Figure 10. 11 Attention for Reboot
4. Click the Yes button to reboot the device to activate the changes.
5. After reboot of device, enter the HDD Information interface.
Menu > HDD> General
6. Select HDD from the list and click
10. 12.
icon to enter the Local HDD Settings interface, as shown in Figure
Figure 10. 12 Local HDD Settings Interface
125
User Manual of INVR-0xA / INVR-0xPOE series NVR
7. Select the Group number for the current HDD.
The default group No. for each HDD is 1.
8. Click the OK button to confirm the settings.
Figure 10. 13 Confirm HDD Group Settings
9. In the pop-up Attention box, click the Yes button to finish the settings.
10.3.2 Setting HDD Property
Purpose:
The HDD property can be set to redundancy, read-only or read/write (R/W). Before setting the HDD property,
please set the storage mode to Group (refer to step1-4 of Chapter Setting HDD Groups ).
A HDD can be set to read-only to prevent important recorded files from being overwritten when the HDD becomes
full in overwrite recording mode.
When the HDD property is set to redundancy, the video can be recorded both onto the redundancy HDD and the
R/W HDD simultaneously so as to ensure high security and reliability of video data.
Steps:
1. Enter the HDD Information interface.
Menu > HDD> General
2. Select HDD from the list and click the
Figure 10. 14.
icon to enter the Local HDD Settings interface, as shown in
Figure 10. 14 Set HDD Property
3. Set the HDD property to R/W, Read-only or Redundancy.
4. Click the OK button to save the settings and exit the interface.
5. In the HDD Information menu, the HDD property will be displayed in the list.
126
User Manual of INVR-0xA / INVR-0xPOE series NVR
At least 2 hard disks must be installed on your NVR when you want to set a HDD to Redundancy, and
there is one HDD with R/W property.
127
User Manual of INVR-0xA / INVR-0xPOE series NVR
10.4 Configuring Quota Mode
Purpose:
Each camera can be configured with allocated quota for the storage of recorded files.
Steps:
1. Enter the Storage Mode interface.
Menu > HDD > Advanced
2. Set the Mode to Quota, as shown in Figure 10. 15.
The NVR must be rebooted to enable the changes to take effect.
Figure 10. 15 Storage Mode Settings Interface
3. Select a camera for which you want to configure quota.
4. Enter the storage capacity in the text fields of Max. Record Capacity (GB), as shown in Figure 10. 16.
Figure 10. 16 Configure Record Quota
5. You can copy the quota settings of the current camera to other cameras if required. Click the Copy button to
enter the Copy Camera menu, as shown in Figure 10. 17.
128
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 10. 17 Copy Settings to Other Camera(s)
6. Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of IP
Camera to select all cameras.
7. Click the OK button to finish the Copy settings and back to the Storage Mode interface.
8. Click the Apply button to apply the settings.
If the quota capacity is set to 0, then all cameras will use the total capacity of HDD for record.
129
User Manual of INVR-0xA / INVR-0xPOE series NVR
10.5 Checking HDD Status
Purpose:
You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case
of HDD failure.
Checking HDD Status in HDD Information Interface
Steps:
1. Enter the HDD Information interface.
Menu > HDD>General
2. Check the status of each HDD which is displayed on the list, as shown in Figure 10. 18.
Figure 10. 18 View HDD Status (1)
If the status of HDD is Normal or Sleeping, it works normally. If the status is Uninitialized or Abnormal,
please initialize the HDD before use. And if the HDD initialization is failed, please replace it with a new
one.
Checking HDD Status in HDD Information Interface
Steps:
1. Enter the System Information interface.
Menu >Maintenance > System Info
2. Click the HDD tab to view the status of each HDD displayed on the list, as shown in Figure 10. 19.
Figure 10. 19 View HDD Status (2)
130
User Manual of INVR-0xA / INVR-0xPOE series NVR
10.6 HDD Detection
Purpose:
The device provides the HDD detection function such as the adopting of the S.M.A.R.T. and the Bad Sector
Detection technique. The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring
system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures.
S.M.A.R.T. Settings
Steps:
1. Enter the S.M.A.R.T Settings interface.
Menu > Maintenance > HDD Detect.
2. Select the HDD to view its S.M.A.R.T information list, as shown in Figure 10. 20.
Figure 10. 20 S.M.A.R.T Settings Interface
The related information of the S.M.A.R.T. is shown on the interface.
You can choose the self-test types as Short Test, Expanded Test or the Conveyance Test.
Click the start button to start the S.M.A.R.T. HDD self-evaluation.
If you want to use the HDD even when the S.M.A.R.T. checking is failed, you can check the checkbox of the
Continue to use the disk when self-evaluation is failed item.
Bad Sector Detection
Steps:
1. Click the Bad Sector Detection tab.
2. Select the HDD No. in the dropdown list you want to configure, and choose All Detection or Key Area
Detection as the detection type.
3. Click the Detect button to start the detection
131
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 10. 21 Bad Sector Detection
And you can click Error info button to see the detailed damage information
And you can also pause/resume or cancel the detection.
132
User Manual of INVR-0xA / INVR-0xPOE series NVR
10.7 Configuring HDD Error Alarms
Purpose:
You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal.
Steps:
1. Enter the Exception interface.
Menu > Configuration > Exceptions
2. Select the Exception Type to HDD Error from the dropdown list.
3. Click the checkbox(s) below to select the HDD error alarm type (s), as shown in Figure 10. 22.
The alarm type can be selected to: Audio Warning, Notify Surveillance Center and Send Email. Please
refer to Chapter Fehler! Verweisquelle konnte nicht gefunden werden..
Figure 10. 22 Configure HDD Error Alarm
4. When the Trigger Alarm Output is selected, you can also select the alarm output to be triggered from the list
below.
5. Click the Apply button to save the settings
133
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 11 Camera Settings
134
User Manual of INVR-0xA / INVR-0xPOE series NVR
11.1 Configuring OSD Settings
Purpose:
You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc.
Steps:
1. Enter the OSD Configuration interface.
Menu > Camera > OSD
2. Select the camera to configure OSD settings.
3. Edit the Camera Name in the text field.
4. Configure the Display Name, Display Date and Display Week by clicking the checkbox.
5. Select the Date Format, Time Format and Display Mode.
Figure 11. 1 OSD Configuration Interface
6. You can use the mouse to click and drag the text frame on the preview window to adjust the OSD position.
7. Click the Apply button to apply the settings.
135
User Manual of INVR-0xA / INVR-0xPOE series NVR
11.2 Configuring Privacy Mask
Purpose:
You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator. The privacy
mask can prevent certain surveillance areas to be viewed or recorded.
Steps:
1. Enter the Privacy Mask Settings interface.
Menu > Camera >Privacy Mask
2. Select the camera to set privacy mask.
3. Click the checkbox of Enable Privacy Mask to enable this feature.
Figure 11. 2 Privacy Mask Settings Interface
4. Use the mouse to draw a zone on the window. The zones will be marked with different frame colors.
Up to 4 privacy masks zones can be configured and the size of each area can be adjusted.
5. The configured privacy mask zones on the window can be cleared by clicking the corresponding Clear
Zone1-4 icons on the right side of the window, or click Clear All to clear all zones.
Figure 11. 3 Set Privacy Mask Area
6. Click the Apply button to save the settings.
136
User Manual of INVR-0xA / INVR-0xPOE series NVR
11.3 Configuring Video Parameters
Steps:
1. Enter the Image Settings interface.
Menu > Camera >Image
Figure 11. 4 Image Settings Interface
2. Select the camera to set image parameters.
3. You can click on the arrow to change the value of each parameter.
4. Click the Apply button to save the settings.
137
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 12 NVR
Management
Maintenance
138
and
User Manual of INVR-0xA / INVR-0xPOE series NVR
12.1 Viewing System Information
12.1.1 Viewing Device Information
Steps:
1. Enter the System Information interface.
Menu >Maintenance >System Info
2. Click the Device Info tab to enter the Device Information menu to view the device name, model, serial No. ,
firmware version and encode version, as shown in Figure 12. 1.
Figure 12. 1 Device Information Interface
12.1.2 Viewing Camera Information
Steps:
1.
Enter the System Information interface.
Menu >Maintenance>System Info
2.
Click the Camera tab to enter the Camera Information menu to view the status of each camera, as shown
in Figure 12. 2.
Figure 12. 2 Camera Information Interface
12.1.3 Viewing Record Information
Steps:
1. Enter the System Information interface.
Menu >Maintenance>System Info
2. Click the Record tab to enter the Record Information menu to view the recording status recording
parameters of each camera, as shown in Figure 12. 3.
139
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 12. 3 Record Information Interface
12.1.4 Viewing Network Information
Steps:
1.
Enter the System Information interface.
Menu >Maintenance>System Info
2.
Click the Network tab to enter the Network Information menu to view the network information, as shown
in Figure 12. 4.
Figure 12. 4 Network Information Interface
12.1.5 Viewing HDD Information
Steps:
1. Enter the System Information interface.
Menu > Maintenance > System Info
2. Click the HDD tab to enter the HDD Information menu to view the HDD status, free space, property, etc..
140
User Manual of INVR-0xA / INVR-0xPOE series NVR
12.2 Searching & Export Log Files
Purpose:
The operation, alarm, exception and information of the NVR can be stored in log files, which can be viewed and
exported at any time.
Steps:
1. Enter the Log Search interface.
Menu >Maintenance>Log Information
Figure 12. 5 Log Search Interface
2. Set the log search conditions to refine your search, including the Start Time, End Time, Major Type and
Minor Type.
3. Click the Search button to start search log files.
4. The matched log files will be displayed on the list shown below.
141
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 12. 6 Log Search Results
Up to 2000 log files can be displayed each time.
5. You can click the
button of each log or double click it to view its detailed information, as shown in
Figure 12. 7. And you can also click the
button to view the related video files if available.
Figure 12. 7 Log Details
6. If you want to export the log files, click the Export button to enter the Export menu, as shown in Figure 12.
8.
142
User Manual of INVR-0xA / INVR-0xPOE series NVR
Figure 12. 8 Export Log Files
7. Select the backup device from the dropdown list of Device Name.
8. Click the Export to export the log files to the selected backup device.
You can click the New Folder button to create new folder in the backup device, or click the Format button
to format the backup device before log export.
 Please connect the backup device to NVR before operating log export.
 The log files exported to the backup device are named by exporting time, e.g.,
20110514124841logBack.txt.
To export all the log files:
You can enter the Log Export interface.
Menu> Maintenance> Log Information> Log Export
Figure 12. 9 Log Export Interface
Choose the HDD No. you want to export he log files to by checking the checkbox of it.
Click the Export button to export all the log files stored in the HDD.
143
User Manual of INVR-0xA / INVR-0xPOE series NVR
12.3 Importing/Exporting Configuration Files
Purpose:
The configuration files of the NVR can be exported to local device for backup; and the configuration files of one
NVR can be imported to multiple NVR devices if they are to be configured with the same parameters.
Steps:
1. Enter the Import/Export Configuration File interface.
Menu > Maintenance >Import/Export
Figure 12. 10 Import/Export Config File
2. Click the Export button to export configuration files to the selected local backup device.
3. To import a configuration file, select the file from the selected backup device and click the Import button.
After the import process is completed, you must reboot the NVR.
After having finished the import of configuration files, the device will reboot automatically.
144
User Manual of INVR-0xA / INVR-0xPOE series NVR
12.4 Upgrading System
Purpose:
The firmware on your NVR can be upgraded by local backup device or remote FTP server.
12.4.1 Upgrading by Local Backup Device
Steps:
1. Connect your NVR with a local backup device where the update firmware file is located.
2. Enter the Upgrade interface.
Menu >Maintenance>Upgrade
3. Click the Local Upgrade tab to enter the local upgrade menu, as shown in Figure 12. 11.
Figure 12. 11 Local Upgrade Interface
4. Select the update file from the backup device.
5. Click the Upgrade button to start upgrading.
6. After the upgrading is complete, reboot the NVR to activate the new firmware.
12.4.2 Upgrading by FTP
Before you start:
Configure PC (running FTP server) and NVR to the same Local Area Network. Run the 3rd-party TFTP software
on the PC and copy the firmware into the root directory of TFTP.
145
User Manual of INVR-0xA / INVR-0xPOE series NVR
Steps:
1. Enter the Upgrade interface.
Menu >Maintenance>Upgrade
2. Click the FTP tab to enter the local upgrade interface, as shown in Figure 12. 12.
Figure 12. 12 FTP Upgrade Interface
3. Enter the FTP Server Address in the text field.
4. Click the Upgrade button to start upgrading.
5. After the upgrading is complete, reboot the NVR to activate the new firmware.
146
User Manual of INVR-0xA / INVR-0xPOE series NVR
12.5 Restoring Default Settings
Steps:
1.
Enter the Default interface.
Menu > Maintenance > Default
Figure 12. 13 Restore Factory Default
2.
Click the OK button to restore the default settings.
Except the network parameters (including IP address, subnet mask, gateway, MTU, default route and
server port), all other parameters of the device will be restored to factory default settings.
147
User Manual of INVR-0xA / INVR-0xPOE series NVR
Chapter 13 Others
148
User Manual of INVR-0xA / INVR-0xPOE series NVR
13.1 Configuring General Settings
Purpose:
You can configure the output resolution, system time, mouse pointer speed through the Menu > Configuration >
General interface.
Steps:
1. Enter the General Settings interface.
Menu >Configuration> General
2. Select the General tab.
Figure 13. 1 General Settings Interface
3. Configure the following settings:
• Language: The default language used is English.
• Resolution: Select the output resolution, which must be the same with the resolution of the monitor
screen.
•
•
•
•
•
•
•
Time Zone: Select the time zone.
Date Format: Select the date format.
System Date: Select the system date.
System Time: Select the system time.
Mouse Pointer Speed: Set the speed of mouse pointer; 4 levels are configurable.
Enable Wizard: Enable/disable the Wizard when the device starts up.
Enable Password: Enable/disable the use of the login password.
4. Click the Apply button to save the settings.
149
User Manual of INVR-0xA / INVR-0xPOE series NVR
13.2 Configuring DST Settings
Steps:
1. Enter the General Settings interface.
Menu >Configuration>General
2. Choose DST Settings tab.
Figure 13. 2 DST Settings Interface
3. You can check the checkbox before the Auto DST Adjustment item.
Or you can manually check the Enable DST checkbox, and then you choose the date of the DST period.
4. Click Apply button to activate the settings.
150
User Manual of INVR-0xA / INVR-0xPOE series NVR
13.3 Configuring More Settings for Device
Parameters
Steps:
1. Enter the General Settings interface.
Menu >Configuration>General
2. Click the More Settings tab to enter the More Settings interface, as shown in Figure 13. 3.
Figure 13. 3 More Settings Interface
3. Configure the following settings:
• Device Name: Edit the name of NVR.
• Device No.: Edit the serial number of NVR. The Device No. can be set in the range of 1~255, and the
default No. is 255. The number is used for the remote and keyboard control.
• Auto Logout: Set timeout time for menu inactivity. E.g., when the timeout time is set to 5 Minutes, then
the system will exit from the current operation menu to live view screen after 5 minutes of menu
inactivity.
• Menu Output Mode: You can choose the menu display on different video output.
4. Click the Apply button to save the settings.
151
User Manual of INVR-0xA / INVR-0xPOE series NVR
13.4 Managing User Accounts
Purpose:
There is a default account in the NVR: Administrator. The Administrator user name is admin and the password is
12345. The Administrator has the permission to add and delete user and configure user parameters.
13.4.1 Adding a User
Steps:
1. Enter the User Management interface.
Menu >Configuration>User
Figure 13. 4 User Management Interface
2. Click the Add button to enter the Add User interface.
Figure 13. 5 Add User Menu
152
User Manual of INVR-0xA / INVR-0xPOE series NVR
3. Enter the information for new user, including User Name, Password, Level and User’s MAC Address.
Level: Set the user level to Operator or Guest. Different user levels have different operating permission.
• Operator: The Operator user level has permission of Two-way Audio in Remote Configuration and all
operating permission in Camera Configuration.
• Guest: The Guest user has no permission of Two-way Audio in Remote Configuration and only has the
local/remote playback in the Camera Configuration.
• User’s MAC Address: The MAC address of the remote PC which logs onto the NVR. If it is configured
and enabled, it only allows the remote user with this MAC address to access the NVR.
4. Click the OK button to save the settings and go back to the User Management interface. The added new user
will be displayed on the list, as shown in Figure 13. 6.
Figure 13. 6 Added User Listed in User Management Interface
5. Select the user from the list and then click the
shown in Figure 13. 7.
button to enter the Permission settings interface, as
Figure 13. 7 User Permission Settings Interface
6. Set the operating permission of Local Configuration, Remote Configuration and Camera Configuration for
the user.
153
User Manual of INVR-0xA / INVR-0xPOE series NVR
Local Configuration
• Local Log Search: Searching and viewing logs and system information of NVR.
• Local Parameters Settings: Configuring parameters, restoring factory default parameters and
importing/exporting configuration files.
• Local Camera Management: The adding, deleting and editing of IP cameras.
• Local Advanced Operation: Operating HDD management (initializing HDD, setting HDD property),
upgrading system firmware, clearing I/O alarm output.
• Local Shutdown Reboot: Shutting down or rebooting the NVR.
Remote Configuration
• Remote Log Search: Remotely viewing logs that are saved on the NVR.
• Remote Parameters Settings: Remotely configuring parameters, restoring factory default parameters
and importing/exporting configuration files.
•
•
•
•
•
Remote Camera Management: Remote adding, deleting and editing of the IP cameras.
Remote Serial Port Control: Configuring settings for RS-232 and RS-485 ports.
Remote Video Output Control: Sending remote button control signal.
Two-Way Audio: Realizing two-way radio between the remote client and the NVR.
Remote Alarm Control: Remotely arming (notify alarm and exception message to the remote client)
and controlling the alarm output.
• Remote Advanced Operation: Remotely operating HDD management (initializing HDD, setting
HDD property), upgrading system firmware, clearing I/O alarm output.
• Remote Shutdown/Reboot: Remotely shutting down or rebooting the NVR.
Camera Configuration
• Remote Live View: Remotely viewing live video of the selected camera (s).
• Local Manual Operation: Locally starting/stopping manual recording and alarm output of the
selected camera (s).
• Remote Manual Operation: Remotely starting/stopping manual recording and alarm output of the
selected camera (s).
•
•
•
•
•
7.
Local Playback: Locally playing back recorded files of the selected camera (s).
Remote Playback: Remotely playing back recorded files of the selected camera (s).
Local PTZ Control: Locally controlling PTZ movement of the selected camera (s).
Remote PTZ Control: Remotely controlling PTZ movement of the selected camera (s).
Local Video Export: Locally exporting recorded files of the selected camera (s).
Click the OK button to save the settings and exit interface.
Only the admin user account has the permission of restoring factory default parameters.
154
User Manual of INVR-0xA / INVR-0xPOE series NVR
13.4.2 Deleting a User
Steps:
1.
Enter the User Management interface.
Menu >Configuration>User
2.
Click to select the user to be deleted from the list.
3.
Click the
icon to delete the selected user.
13.4.3 Editing a User
Steps:
1.
Enter the User Management interface.
Menu >Configuration>User
2.
Select the user to be edited from the list, as shown in Figure 13. 6.
3.
Click the
icon to enter the Edit User interface, as shown in Figure 13. 8.
The admin user can also be edited.
Operator and Guest
Admin
Figure 13. 8 Edit User Interface
155
User Manual of INVR-0xA / INVR-0xPOE series NVR
4.
Edit the corresponding parameters.
• Operator and Guest
You can edit the user information, including user name, password, permission level and MAC address.
Check the checkbox of Change Password if you want to change the password, and input the new one in
the text field of Password and Confirm.
• Admin
You are only allowed to edit password and MAC address.
Check the checkbox of Change Password if you want to change the password, and the input the correct
old password, and the new one in the text field of Password and Confirm.
5.
Click the OK button to save the settings and exit the menu.
156
User Manual of INVR-0xA / INVR-0xPOE series NVR
Appendix
157
User Manual of INVR-0xA / INVR-0xPOE series NVR
Glossary
• Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting
a lower resolution stream over the network. The two streams are generated by the DVR, with the main
stream having a maximum resolution of 4CIF and the sub-stream having a maximum resolution of CIF.
• HDD: Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters
with magnetic surfaces.
• DHCP: Dynamic Host Configuration Protocol (DHCP) is a network application protocol used by devices
(DHCP clients) to obtain configuration information for operation in an Internet Protocol network.
• HTTP: Acronym for Hypertext Transfer Protocol. A protocol to transfer hypertext request and information
between servers and browsers over a network
• PPPoE: PPPoE, Point-to-Point Protocol over Ethernet, is a network protocol for encapsulating
Point-to-Point Protocol (PPP) frames inside Ethernet frames. It is used mainly with ADSL services where
individual users connect to the ADSL transceiver (modem) over Ethernet and in plain Metro Ethernet
networks.
• DDNS: Dynamic DNS is a method, protocol, or network service that provides the capability for a
networked device, such as a router or computer system using the Internet Protocol Suite, to notify a domain
name server to change, in real time (ad-hoc) the active DNS configuration of its configured hostnames,
addresses or other information stored in DNS.
• Hybrid DVR: A hybrid DVR is a combination of a DVR and NVR.
• NTP: Acronym for Network Time Protocol. A protocol designed to synchronize the clocks of computers
over a network.
• NTSC: Acronym for National Television System Committee. NTSC is an analog television standard used
in such countries as the United States and Japan. Each frame of anNTSC signal contains 525 scan lines at
60Hz.
• NVR: Acronym for Network Video Recorder. An NVR can be a PC-based or embedded system used for
centralized management and storage for IP cameras, IP Domes and other DVRs.
• PAL: Acronym for Phase Alternating Line. PAL is also another video standard used in broadcast
televisions systems in large parts of the world. PAL signal contains 625 scan lines at 50Hz.
• PTZ: Acronym for Pan, Tilt, Zoom. PTZ cameras are motor driven systems that allow the camera to pan
left and right, tilt up and down and zoom in and out.
• USB: Acronym for Universal Serial Bus. USB is a plug-and-play serial bus standard to interface devices to
a host computer.
158
User Manual of INVR-0xA / INVR-0xPOE series NVR
Troubleshooting
 No image displayed on the monitor after starting up normally.
Possible Reasons
a)
No VGA or HDMI connections.
b)
Connection cable is damaged.
c)
Input mode of the monitor is incorrect.
Steps
1. Verify the device is connected with the monitor via HDMI or VGA cable.
If not, please connect the device with the monitor and reboot.
2. Verify the connection cable is good.
If there is still no image display on the monitor after rebooting, please check if the connection cable is good,
and change a cable to connect again.
3. Verify Input mode of the monitor is correct.
Please check the input mode of the monitor matches with the output mode of the device (e.g. if the output
mode of NVR is HDMI output, then the input mode of monitor must be the HDMI input). And if not, please
modify the input mode of monitor.
4. Check if the fault is solved by the step 1 to step 3.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
 There is an audible warning sound “Di-Di-Di-DiDi” after a new bought NVR starts up.
Possible Reasons
a)
No HDD is installed in the device.
b)
The installed HDD has not been initialized.
c)
The installed HDD is not compatible with the NVR or is broken-down.
Steps
1.Verify at least one HDD is installed in the NVR.
1) If not, please install the compatible HDD.
Please refer to the “Quick Operation Guide” for the HDD installation steps.
2) If you don’t want to install a HDD, select “Menu>Configuration > Exceptions”, and uncheck the Audible
Warning checkbox of “HDD Error”.
2.Verify the HDD is initialized.
1) Select “Menu>HDD>General”.
2) If the status of the HDD is “Uninitialized”, please check the checkbox of corresponding HDD and click
the “Init” button.
3.Verify the HDD is detected or is in good condition.
1) Select “Menu>HDD>General”.
2) If the HDD is not detected or the status is “Abnormal”, please replace the dedicated HDD according to
the requirement.
4.Check if the fault is solved by the step 1 to step 3.
1) If it is solved, finish the process.
2) If not, please contact the engineer from our manufacturer to do the further process.
159
User Manual of INVR-0xA / INVR-0xPOE series NVR
 The status of the added IPC displays as “Disconnected” when it is connected through Private Protocol.
Select “Menu>Camera>Camera>IP Camera” to get the camera status.
Possible Reasons
a)
Network failure, and the NVR and IPC lost connections.
b)
The configured parameters are incorrect when adding the IPC.
c)
Insufficient bandwidth.
Steps
1. Verify the network is connected.
1) Connect the NVR and PC with the RS-232 cable.
2) Open the Super Terminal software, and execute the ping command. Input “ping IP” (e.g. ping
172.6.22.131).
Simultaneously press Ctrl and C to exit the ping command.
If there exists return information and the time value is little, the network is normal.
2. Verify the configuration parameters are correct.
1) Select “Menu>Camera>Camera>IP Camera”.
2) Verify the following parameters are the same with those of the connected IP devices, including IP address,
protocol, management port, user name and password.
3. Verify the whether the bandwidth is enough.
1) Select “Menu >Maintenance > Net Detect > Network Stat.”.
2) Check the usage of the access bandwidth, and see if the total bandwidth has reached its limit.
4. Check if the fault is solved by the step 1 to step 3.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
 The IPC frequently goes online and offline and the status of it displays as “Disconnected”.
Possible Reasons
a)
The IPC and the NVR versions are not compatible.
b)
Unstable power supply of IPC.
c)
Unstable network between IPC and NVR.
d)
Limited flow by the switch connected with IPC and NVR.
Steps
1. Verify the IPC and the NVR versions are compatible.
1) Enter the IPC Management interface “Menu > Camera > Camera>IP Camera”, and view the firmware
version of connected IPC.
2) Enter the System Info interface “Menu>Maintenance>System Info>Device Info”, and view the firmware
version of NVR.
2. Verify power supply of IPC is stable.
1) Verify the power indicator is normal.
2) When the IPC is offline, please try the ping command on PC to check if the PC connects with the IPC.
3. Verify the network between IPC and NVR is stable.
1) When the IPC is offline, connect PC and NVR with the RS-232 cable.
2) Open the Super Terminal, use the ping command and keep sending large data packages to the connected
IPC, and check if there exists packet loss.
160
User Manual of INVR-0xA / INVR-0xPOE series NVR
Simultaneously press Ctrl and C to exit the ping command.
Example: Input ping 172.6.22.131 –l 1472 –f.
4. Verify the switch is not flow control.
Check the brand, model of the switch connecting IPC and NVR, and contact with the manufacturer of the
switch to check if it has the function of flow control. If so, please turn it down.
5. Check if the fault is solved by the step 1 to step 4.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
 No monitor connected with the NVR locally and when you manage the IPC to connect with the device by
web browser remotely, of which the status displays as Connected. And then you connect the device with
the monitor via VGA or HDMI interface and reboot the device, there is black screen with the mouse
cursor.
Connect the NVR with the monitor before startup via VGA or HDMI interface, and manage the IPC to
connect with the device locally or remotely, the status of IPC displays as Connect. And then connect the
device with the CVBS, and there is black screen either.
Possible Reasons:
After connecting the IPC to the NVR, the image is output via the main spot interface by default.
Steps:
1. Enable the output channel.
2. Select “Menu > Configuration > Live View > View”, and select video output interface in the drop-down list
and configure the window you want to view.
 The view settings can only be configured by the local operation of NVR.
 Different camera orders and window-division modes can be set for different output interfaces
separately, and digits like “D1”and “D2” stands for the channel number, and “X” means the selected
window has no image output.
3. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
 Live view stuck when video output locally.
Possible Reasons:
a)
Poor network between NVR and IPC, and there exists packet loss during the transmission.
b)
The motion detection and alarm functions are enabled, and the parameters of Main Stream (Normal) and
Main Stream (Event) are different. So the image looks stuck due to the image changes between different
resolutions.
c)
The frame rate has not reached the real-time frame rate.
Steps:
1. Verify the network between NVR and IPC is connected.
1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232 cable.
2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 –l 1472 –f” (the IP address
may change according to the real condition), and check if there exists packet loss.
Simultaneously press Ctrl and C to exit the ping command.
2. Check the parameters of Main Stream (Normal) and Main Stream (Event).
161
User Manual of INVR-0xA / INVR-0xPOE series NVR
Select “Menu > Record > Parameters > Record”, and set the resolution of Main Stream (Event) the same as
the one of Main Stream (Normal).
3. Verify the frame rate is real-time frame rate.
Select “Menu > Record > Parameters > Record”, and set the Frame rate to Full Frame.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
 Live view stuck when video output remotely via the Internet Explorer or platform software.
Possible Reasons:
a) Poor network between NVR and IPC, and there exists packet loss during the transmission.
b)Poor network between NVR and PC, and there exists packet loss during the transmission.
c) The performances of hardware are not good enough, including CPU, memory, etc..
Steps:
1. Verify the network between NVR and IPC is connected.
1)
When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232 cable.
2)
Open the Super Terminal, and execute the command of “ping 192.168.0.0 –l 1472 –f” (the IP address
may change according to the real condition), and check if there exists packet loss.
Simultaneously press Ctrl and C to exit the ping command.
2. Verify the network between NVR and PC is connected.
1)
Open the cmd window in the Start menu, or you can press “windows+R” shortcut key to open it.
2)
Use the ping command to send large packet to the NVR, execute the command of “ping 192.168.0.0 –l
1472 –f” (the IP address may change according to the real condition), and check if there exists packet
loss.
Simultaneously press Ctrl and C to exit the ping command.
3. Verify the hardware of the PC is good enough.
Simultaneously press Ctrl, Alt and Delete to enter the windows task management interface, as shown in the
following figure.
162
User Manual of INVR-0xA / INVR-0xPOE series NVR
Windows task management interface
Select the “Performance” tab; check the status of the CPU and Memory.
If the resource is not enough, please end some unnecessary processes.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
When using the NVR to get the live view audio, there is no sound or there is too much noise, or the volume is
too low.
Possible Reasons:
a) Cable between the pickup and IPC is not connected well; impedance mismatches or incompatible.
b) The stream type is not set as “Video & Audio”.
c) The encoding standard is not supported with NVR.
Steps:
1. Verify the cable between the pickup and IPC is connected well; impedance matches and compatible.
Log in the IPC directly, and turn the audio on, check if the sound is normal. If not, please contact the
manufacturer of the IPC.
2. Verify the setting parameters are correct.
Select “Menu > Record > Parameters > Record”, and set the Stream Type as “Audio & Video”.
3. Verify the audio encoding standard of the IPC is supported by the NVR.
NVR supports G722.1 and G711 standards, and if the encoding parameter of the input audio is not one of the
previous two standards, you can log in the IPC to configure it to the supported standard.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
The image gets stuck when NVR is playing back by single or multi-channel.
Possible Reasons:
a) Poor network between NVR and IPC, and there exists packet loss during the transmission.
163
User Manual of INVR-0xA / INVR-0xPOE series NVR
b) The motion detection and alarm functions are enabled, and the parameters of Main Stream (Normal) and
Main Stream (Event) are different. So the image looks stuck due to the image changes between different
resolutions.
c) The frame rate is not the real-time frame rate.
d) The NVR supports up to 16-channel synchronize playback at the resolution of 4CIF, if you want a
16-channel synchronize playback at the resolution of 720p, the frame extracting may occur, which leads to
a slight stuck.
Steps:
1. Verify the network between NVR and IPC is connected.
1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232 cable.
2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 –l 1472 –f” (the IP address may
change according to the real condition), and check if there exists packet loss.
Simultaneously press the Ctrl and C to exit the ping command.
2. Check the parameters of Main Stream (Normal) and Main Stream (Event).
Select “Menu > Record > Parameters > Record”, and set the resolution of Main Stream (Event) the same as
the one of Main Stream (Normal).
3. Verify the frame rate is real-time frame rate.
Select “Menu > Record > Parameters > Record”, and set the Frame Rate to “Full Frame”.
4. Verify the hardware can afford the playback.
Reduce the channel number of playback.
Select “Menu > Record > Parameters > Record”, and set the resolution and bitrate to a lower level.
5. Reduce the number of local playback channel.
Select “Menu > Playback”, and uncheck the checkbox of unnecessary channels.
6. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
No record file found in the NVR local HDD, and prompt “No record file found”.
Possible Reasons:
a) The time setting of system is incorrect.
b) The search condition is incorrect.
c) The HDD is error or not detected.
Steps:
1. Verify the system time setting is correct.
Select “Menu > Configuration > General > General”, and verify the “Device Time” is correct.
2. Verify the search condition is correct.
Select “Playback”, and verify the channel and time are correct.
3. Verify the HDD status is normal.
Select “Menu > HDD > General” to view the HDD status, and verify the HDD is detected and can be read
and written normally.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our manufacturer to do the further process.
164
User Manual of INVR-0xA / INVR-0xPOE series NVR
List of Compatible IP Cameras
ONVIF compatibility refers to the camera can be supported both when it uses the ONVIF protocol and its
private protocols. Only ONVIF is supported refers to the camera can only be supported when it uses the
ONVIF protocol. Only AXIS is supported refers to the function can only be supported when it uses the
AXIS protocol.
IPC Manufacturer or
Max.
Model
Version
Protocol
ACTI
Sub-stream
Audio
Resolution
TCM4301-10D-X-00083
A1D-310-V4.12.09-AC
1280×1024
×
√
TCM5311-11D-X-00023
A1D-310-V4.12.09-AC
1280×960
×
√
TCM3401-09L-X-00227
A1D-220-V3.13.16-AC
1280×1024
×
×
AV8185DN
65172
1600×1200
×
×
AV1305M
65175
1280×1024
√
×
AV2155
65143
1600×1200
√
×
AV2815
65220
1920×1080
√
×
AV3105M
65175
1920×1080
√
×
AV5105
65175
1920×1080
√
×
M1114
5.09.1
1024×640
√
×
5.21
704×576
ARECONT
√(Only AXIS is
M3011(ONVIF
compatibility)
×
supported)
M3014(ONVIF
5.21.1
1280×800
√
5.11.2
768×576
√
×
compatibility)
P3301(ONVIF
compatibility)
AXIS
√(Only AXIS is
supported)
P3304(ONVIF
5.20
1440×900
√
compatibility)
√(Only AXIS is
supported)
P3343(ONVIF
5.20.1
800×600
√
compatibility)
√(Only AXIS is
supported)
P3344(ONVIF
5.20.1
1440×900
√
compatibility)
√(Only AXIS is
supported)
P5532
5.15
720×576
√
×
Q7404
5.02
720×576
√
√
AutoDome Jr 800 HD
39500450
1920×1080
×
√
NBC 265 P
07500453
1280×720
×
√
Dinion NBN-921-P
10500453
1280×720
×
√
V3.1.0.8
1280×1024
×
√
V3.2.1.3
1280×1024
×
√
Bosch
(ONVIF compatibility)
FB-130Np (ONVIF
compatibility)
Brickcom
CB-500Ap (ONVIF
compatibility)
165
User Manual of INVR-0xA / INVR-0xPOE series NVR
IPC Manufacturer or
Max.
Model
Version
Protocol
Canon
Panasonic
Sub-stream
Audio
Resolution
WFB-100Ap
V3.1.0.9
1280×800
×
√
VB-M400
Ver.+1.0.0
1280×960
×
√
VB-M6000D
Ver.+1.0.0
1280×960
×
×
VB-M7000F
Ver.+1.0.0
1280×960
×
√
WV-SW152(ONVIF
Application:1.66
800×600
√
×
compatibility)
Image data:1.05
WV-SC386(ONVIF
Application:1.66
1280×960
√
√
compatibility)
Image data:1.05
WV-SW155(ONVIF
Application:1.66
1280×960
√
×
compatibility)
Image data:1.05
WV-SW316(ONVIF
Application:1.66
1280×960
√
√
compatibility)
Image data:2.03
WV-SP105(ONVIF
Application:1.66
1280×960
√
×
compatibility)
Image data:1.03
WV-SF132(ONVIF
Application:1.66
640×360
√
×
compatibility)
Image data:1.03
WV-SP102(ONVIF
Application:1.66
640×480
√
×
compatibility)
Image data:1.03
WV-SP509(ONVIF
Application:1.30
1280×960
√
√
compatibility)
Image data:2.21
WV-SW559(ONVIF
Application:1.30
1920×1080
√
√
compatibility)
Image data:2.21
WV-SW558(ONVIF
Application:1.30
1920×1080
√
×
compatibility)
Image data:2.21
WV-SW355(ONVIF
Application:1.66
1280×960
√
√
compatibility)
Image data:1.04
WV-SW352(ONVIF
Application:1.66
800×600
√
√
compatibility)
Image data:1.04
WV-SF342(ONVIF
Application:1.66
800×600
√
√
compatibility)
Image data:1.06
WV-SF332(ONVIF
Application:1.66
800×600
√
√
compatibility)
Image data:1.06
WV-SF346(ONVIF
Application:1.66
1280×960
√
√
compatibility)
Image data:1.06
1280×960
√
√
1280×960
√
√
1280×960
√
×
1920×1080
√
×
WV-SP306H
Application:1.34
Image data:1.06
WV-SP336H
Application:1.06
Image data:1.06
D5118
1.8.2-201203272.9310-A1.7852
PELCO
IXE20DN-AAXVUU2
1.8.2-201203272.9081-A1.7852
166
User Manual of INVR-0xA / INVR-0xPOE series NVR
IPC Manufacturer or
Max.
Model
Version
Protocol
IX30DN-ACFZHB3
1.8.2-201203272.9080-A1.7852
SAMSUNG
2048×1536
Audio
√
×
√(Only ONVIF
SNB-5000P
V2.00_110727
1280×1024
√
is supported)
(ONVIF compatibility)
SANYO
Sub-stream
Resolution
VCC-HD2300P
2.03-02(110318-00)
1920×1080
×
×
VCC-HD2500P
2.02-02(110208-00)
1920×1080
×
√
VCC-HD4600P
2.03-02(110315-00)
1920×1080
×
√
SNC-CH220
1.50.00
1920×1080
×
×
1.73.00
1280×720
√
√
1.53.00
1920×1080
√
√
1.50.00
2048×1536
×
×
0203a
640×480
×
×
0107a
1280×800
×
×
0104a
1600×1200
×
√
0102a
640×480
×
×
0105b
1280×800
×
×
D5110
MG.1.6.03P8
1280×1024
√
×
F3106
M2.1.6.03P8
1280×1024
√
√
F3110
M2.1.6.01
1280×720
√
√
F3206
MG.1.6.02c045
1920×1080
√
√
F531E
LM.1.6.18P10
640×480
√
√
SNC-RH124(ONVIF
compatibility)
SONY
SNC-EP580(ONVIF
compatibility)
SNC-DH220T(Only
ONVIF is supported)
IP7133
FD8134(ONVIF
compatibility)
IP8161(ONVIF
Vivotek
compatibility)
IP8331(ONVIF
compatibility)
IP8332(ONVIF
compatibility)
ZAVIO
167