DP-22S/22L/24S
Instruction Manual
Ver.1
Correct operation and periodic maintenance are
essential for ensuring safe use of this machine.
Thoroughly read this manual before using this
machine.
DUPLO CORPORATION
Store this manual so that it can be retrieved whenever needed.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Introduction
Thank you for your purchase of the Duprinter DP-22S/22L/24S.
To ensure safe and efficient prolonged use of this machine, read and thoroughly understand this manual before
using this machine. After using this manual, be sure to keep it in a place to handy reference.
1
2
PLEASE NOTE
In the interest of upgrading our products, specifications and other data given in this manual are subject to
change without notice. If the manual contains anything that you do not understand, contact the manufacturer for clarification.
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Function Quick Reference
The following is a quick reference to the functions of the DP-22S/22L/24S printer.
Enlargement/Reduction ........ (a P.39)
This function copies a document on one standard paper size to another larger or smaller standard paper size.
B4 Printout
A4 Document
B5 Printout
94% Reduction
....... (a P.40)
This function slightly reduces the size of a document when printing to the same standard paper size as the document.
A4 Document
A4 Printout
(94%)
1%-Step Enlargement and Reduction
......... (a P.42)
This function enlarges or reduces a document in 1% steps between 50% and 200%.
Printout
Document
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Book Shadow Eraser Mode ......... (a P.63)
This function erases the shadows on the center or edges of book or other folded documents when printing the open
spread.
1
Printout
With shadow eraser
Document
2
Printout
Without shadow eraser
Text/Photograph/Text and Photograph Mode
......... (a P.47)
This function selects the optimum print quality to match the document.
2-up Function
Text
Text/Photograph
ABCDEFGH
ABCDEFGH
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
tuvwxyz
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
tuvwxyz
ABCDEFGHIJKLNO
PQRSTUVWXYZ
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
Photograph
......... (a P.58)
This function prints 2 images of a document on one page.
Document
Printout
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2-in-1 Layout
Available only with ADF installed
......... (a P.61)
This function prints two different documents on one page.
Documents
Printout
Sectional Printing
........ (a P.67)
You can print the specified number of sets of copies in each set.
Document
1st set
5 copies x 2 sets
1
1
2nd set
3 copies x 4 sets
1
1
3rd set
2 copies x 5 sets
1
1
1
1
1
1
1
1
Changing Print Quantity per Document ......... (a P.71)
This function changes the number of prints made from each document.
Documents
1
1st document
5 copies x 2 sets
1
2
2
1
3
2nd document
3 copies x 4 sets
3rd document
2 copies x 5 sets
3
2
3
2
3
2
3
3
4
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Contents
Introduction ......................................................................................................................... 1
Function Quick Reference ................................................................................................. 2
Notes on Safety (Please Read and Observe) ................................................................... 8
Safety Precautions .............................................................................................. 8
Warning Sticker ........................................................................................................ 11
Positioning the Machine ........................................................................................... 12
Maintenance ............................................................................................................. 13
Printing and Duplicating Cautions ............................................................................ 14
Conventions Used in This Manual ............................................................................ 15
Chapter 1
Before Using This Machine
System Setup .................................................................................................................... 18
Part Names and Their Functions ..................................................................................... 19
Printer Appearance .................................................................................................. 19
Control Panel ............................................................................................................ 22
LCD Panel ................................................................................................................ 24
Turning Power ON/OFF .................................................................................................... 25
Turning ON Printer Power ......................................................................................... 25
Turning OFF Printer Power ....................................................................................... 26
Standard Mode ......................................................................................................... 26
Key Card Counter [Available only with Key Card Counter installed] ......................... 27
Document/Printing Paper Specification ......................................................................... 28
Acceptable Documents ............................................................................................ 28
Acceptable Printing Paper ........................................................................................ 28
How Platemaking and Printing is Performed ................................................................. 29
Platemaking .............................................................................................................. 29
Printing ..................................................................................................................... 29
Chapter 2
Printing Using Basic Functions
Basic Printmaking ............................................................................................................ 32
Loading and Replacing Paper ......................................................................................... 34
Loading Paper .......................................................................................................... 34
Adjusting Paper Feed Pressure ................................................................................ 35
Loading Documents ......................................................................................................... 36
Positioning the Document ......................................................................................... 36
Loading Document on Document Glass Plate ......................................................... 37
Loading Document in ADF [Available only when ADF installed] .............................. 38
Enlargement and Reduction ............................................................................................ 39
Enlarging/Reducing from Standard-Size Document to Standard-Size Paper .......... 39
94% Reduction ......................................................................................................... 40
1% - Step Enlargement and Reduction .................................................................... 42
Selecting Printing Paper Size .......................................................................................... 44
Text/Photograph/Text and Photograph Mode ................................................................ 47
Print Output ....................................................................................................................... 49
Installing Print Tray ................................................................................................... 49
Truing up Printed Pages ........................................................................................... 51
5
1
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Contents
Chapter 3
Printing With Various Function
Saving Settings ................................................................................................................. 54
Saving Settings ........................................................................................................ 54
Retrieving Settings ................................................................................................... 56
Multiple Printing on One Page......................................................................................... 58
2-up Function ........................................................................................................... 58
2-in-1 Layout [Available only when ADF installed] .................................................... 61
Book Shadow Eraser Mode ............................................................................................. 63
Adjusting Plate Darkness ................................................................................................ 65
Sectional Printing ............................................................................................................. 67
Sectional Printing ..................................................................................................... 67
Sectional Printing (changing print quantity per document) ....................................... 71
Dividing Sections with Tape [Available only with Tape Cluster Device] ..................... 74
Chapter 4
Miscellaneous Functions
Confidential Safeguard Function .................................................................................... 78
Total Counter Display Function ....................................................................................... 79
Print Speed Adjustment Function ................................................................................... 80
Printing Position Adjustment Function .......................................................................... 81
On-Line Print Function [Available Only With Interface Kit Installed] ........................... 82
Chapter 5
Replacing Consumables
Replacing the Ink Pack ..................................................................................................... 84
Replacing the Master Roll ................................................................................................ 87
Replacing the Master Ejection Core ............................................................................... 90
Replacing the Drum Unit .................................................................................................. 92
Removing the Drum Unit .......................................................................................... 92
Installing the Drum Unit ............................................................................................ 94
Chapter 6
Troubleshooting
Countermeasures to Troubles ......................................................................................... 98
Power Does Not Turn ON ......................................................................................... 98
Platemaking/Printing is Not Possible ........................................................................ 98
Error Messages ................................................................................................................. 99
Supplying or Changing Paper While Printing .............................................................. 103
If Paper Runs Out During Printing .......................................................................... 103
Adding Paper While Printing .................................................................................. 103
Changing Paper Selection While Printing .............................................................. 105
Paper Jams ..................................................................................................................... 107
When “PAPER LEFT JAM” is Displayed (Feed Tray) ............................................. 107
When “PAPER RIGHT JAM” is Displayed (Print Tray) ........................................... 108
When “MAST. EJECT ERROR” is Displayed ................................................................. 111
When “MASTER SET MISS” is Displayed .................................................................... 114
6
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Contents
Chapter 7
Specifications and Maintenance
Specifications ................................................................................................................. 118
Appendix
Index ................................................................................................................................ 122
1
Quick Operation Guide .................................................................................................. 124
2
7
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes on Safety (Please Read and Observe)
Safety Precautions
Various symbols and pictures are used in this manual and on the stickers affixed to the machine. These symbols and
pictures provide warnings and instructions to prevent danger to you or other personnel, and to prevent damage to office
property. The meanings of these symbols and pictures are explained below.
Indicates a high degree of potential danger. If the warning is ignored, death or serious
WARNING injury may result.
Indicates a medium degree of potential danger. If the caution is ignored, medium injury or
CAUTION damage to property may result.
[Examples of Pictorial Symbols]
A circle with a line through it indicates a prohibited action. The particular act prohibited is indicated by a picture inside the circle. (In the example shown here, the prohibited
act is disassembly.)
A black disc indicates an instruction, or sometimes a prohibited action. The instruction
itself is indicated by pictorial symbols drawn in white on the disc. (In the example shown
here, the instruction is “Remove the plug from the outlet.”)
• These are particularly important safety points and should always be observed.
WARNING
If the machine is used after foreign matter (metal fragments, water, or liquid) has entered the
machine, this may result in fire or electric shock.
• Turn the main unit’s power switch OFF, and then remove the power plug from the outlet. Contact
the sales distributor.
If the machine is used after heat, smoke, strange smell, or other abnormality is detected, this may
result in fire or electric shock.
• Turn the main unit’s power switch OFF, and then remove the power plug from the outlet. Contact
the sales distributor.
Use only the power cord that is provided among the accessories.
8
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes on Safety (Please Read and Observe)
WARNING
Do not modify the machine.
• Doing so may result in fire or electric shock.
1
Do not remove the rear lid, cabinet, or covers from the machine.
• The inside of the machine contains high-voltage parts, which may cause electric shock.
2
Do not remove or insert the power plug with wet hands.
• Doing so may result in electric shock.
Do not damage, break, or modify the power cord.
• Do not place heavy objects on, tug, or unnecessarily bend the power cord. Doing so may result in
fire or electric shock.
Do not insert or drop metal, flammable material, or other matter through the ventilation holes into
the machine interior.
• Doing so may result in fire or electric shock.
Do not place flower vases, flowerpots, cups, or water containers (including metal containers) on top
of the machine.
• Fire or electric shock may result if liquid spills inside the machine.
Do not use a source voltage other than that specified. Do not connect two or more loads to a single
outlet.
• Doing so may result in fire or electric shock.
Do not place the machine in a humid or dusty area.
• Doing so may result in fire or electric shock.
9
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes on Safety (Please Read and Observe)
CAUTION
Before moving the machine, remove the power plug from the outlet.
• If the cord is damaged, this may result in fire or electric shock.
Remove the power plug itself, not the cord.
• Tugging the cord may damage it (expose conductors, or cause disconnections, etc.), resulting in
fire or electric shock.
Do not place the machine in an unstable position, such as on an unsteady support or sloping area.
• If the machine is dropped or falls over, this could result in personal injury.
Once the machine is in position, secure in place using the casters.
• If the machine falls over, this could result in personal injury.
10
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes on Safety (Please Read and Observe)
Warning Sticker
Keep the WARNING stickers clean at all times. If stickers become damaged or come off, replace them with new ones.
1
WARNING
● Do not remove this cover. The inside of the printer contains movable cutting instruments,
L1-T3060
contact with which could result in injury.
2
WARNING
Do NOT touch the drum or rollers
when you operate the jog switch.
Do NOT put hands Inside
machine while it is operatung.
Hands could get caught up
or crushed.
L5-T3020
No.
q
w
Parts No.
L1-T3060
L5-T3020
Name
Warning Sticker 1
Warning Sticker 2
Q’ty
1
1
11
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes on Safety (Please Read and Observe)
Positioning the Machine
Installing the machine on a flat, stable surface.
,
Avoid installing the machine in a dusty area.
Avoid installing the machine in the direct sunlight or heat,
such as near a stove. Ink may deteriorate and may cause
bad prints, while the machine may indicate errors due to
overheating caused by sunlight. Also avoid hot, cold, or
humid areas since paper may absorb moisture, causing
paper jams or wrinkles.
12
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes on Safety (Please Read and Observe)
Maintenance
Clean the exterior of the machine as described below.
Tightly wring a soft cloth that has been moistened with
water or neutral detergent, and wipe dirt from the machine’s surface.
Never use alcohol or organic solvents. Doing so may
discolor or damage the machine exterior.
1
2
Dust and clean the machine at least once a week to avoid
breakdowns.
Before cleaning, turn the power switch OFF, and then
remove the power plug from the outlet.
To clean the reader glass, use a dry, soft cloth and lightly
wipe off any dirt.
WARNING
• Before cleaning, remove the power plug from the outlet.
Doing so may result in fire or electric shock.
• Prevent water and neutral cleansers from getting inside the machine. If liquids spill inside the machine, contact your agent immediately. Using the machine with water spilled inside may result in fire or
electric shock.
13
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes on Safety (Please Read and Observe)
Printing and Duplicating Cautions
There are restrictions on what you may print on this printer. Please be aware that there are some printed materials that
are illegal even to possess.
1. Printed Matter Banned by Law
• Paper money, currency, government bonds and national and local bonds cannot be duplicated, even if they are
stamped with the “sample” seal.
• Paper money, currency and bonds, etc. that are valid in a foreign country cannot be duplicated.
• Unused postage stamps and postcards cannot be duplicated without government consent.
• Government-issued papers pertaining to stamps, liquor and sales tax laws cannot be duplicated.
2. Printed Matter that Require Caution
• Printed-issued securities (stocks, bills and checks, etc.), passes and tickets require caution in duplicating unless a
business is duplicating them for required number for their own business needs.
• Government-issued passports, public- and private-issued driver’s licenses, permits, IDs, passes, food stamps, etc.
require caution in duplicating.
3. Copyrighted Materials
Books, music, artwork, prints, maps, diagrams, movies, photography, etc. are banned from duplicating outside the
limits of private home use and their related non-sale usage.
14
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes on Safety (Please Read and Observe)
Conventions Used in This Manual
Each page of descriptions in this manual of how to operate the DP-22S/22L/24S is set up as follows.
1
Enlargement and Reduction
Title (Function)
Enlarging/Reducing from Standard-Size Document to Standard-Size Paper
You can enlarge or reduce a standard-size document onto standard-size printing paper.
1
The following zoom ratios are available when enlarging or reducing a standard-size document onto standard-size
printing paper.
■ Enlargements
You can enlarge a standard-size document onto standard-size paper using the following zoom ratios:
<DP-24S>
B5 → B4 / A5 → A4 .. 141%
A4 → B4 / A5 → B5 .. 122%
B5 → A4 .................... 115%
2
A4 Printout
A5 Document
Printing Using Basic Functions
Description of function and
example of printing
The illustration is designed to
indicate the result of using the
selected function.
● European paper sizes
<DP-22S>
A5 → A4 .................... 141%
A5 → B5 .................... 122%
B5 → A4 .................... 115%
● U.S. paper sizes
<DP-22L>
141%
ST → LTR .................. 129%
121%
■ Reductions
You can reduce a standard-size document onto standard-size paper using the following zoom ratios:
● European paper sizes
<DP-22S>
A4 → B5 ...................... 86%
B4 → A4 / B5 → A5 .... 81%
A3 → A4 / B4 → B5 .... 70%
● U.S. paper sizes
<DP-22L>
LGL→ LTR .................. 77%
LDG→ LGL ................. 74%
LDG→ LTR ................. 64%
<DP-24S>
A3 → B4 / A4→ B5 ..... 86%
B4 → A4 / B5 → A5 .... 81%
A3 → A4 / B4 → B5 .... 70%
A3 Document
A4 Printout
IMPORTANT
• Set the desired zoom ratio before starting the platemaking process.
Description of operational steps
Each step is described in detail.
Illustrations
The illustrations provide a visual
reference to which keys to operate
and other related conditions.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(ENLARGEMENT) key or
DUCTION) key.
(RE-
1:1
1
4
STD
STD
7
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
39
■ Pictorial Symbols and Other Notations Used in This Manual
IMPORTANT : Introduces instructions for correct operation of the machine. If these instructions are ignored,
the machine may not be able to operate at optimum performance or may break down.
Tip
: Introduces information that is useful for operation and maintenance of the machine, or
information about the machine’s performance, etc.
Continue Page •••
(a P.00 “xxxx”)
: Indicates that the description of the operating sequence is continued on the next page.
: Indicates the page number and item containing related information.
In the text of this manual, keys are indicated as follows:
:
(PLATE MAKING) key
15
2
Chapter
1
1
This chapter contains essential information such as the names of the machine parts, the
names and functions of keys, etc., on the control panel, and the sizes of documents and
printing papers that you can use. Please be sure to read this chapter carefully before
attempting to use the printer.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
System Setup ..................................................................................................... 18
Part Names and Their Functions ...................................................................... 19
Printer Appearance ...................................................................................... 19
Control Panel ............................................................................................... 22
LCD Panel .................................................................................................... 24
Turning Power ON/OFF ...................................................................................... 25
Turning ON Printer Power ............................................................................ 25
Turning OFF Printer Power .......................................................................... 26
Standard Mode ............................................................................................ 26
Key Card Counter [Available only with Key Card Counter installed] ............ 27
Document/Printing Paper Specification .......................................................... 28
Acceptable Documents ................................................................................ 28
Acceptable Printing Paper ........................................................................... 28
How Platemaking and Printing is Performed .................................................. 29
Platemaking ................................................................................................. 29
Printing ......................................................................................................... 29
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Before Using This Machine
Before Using This Machine
System Setup
The machine and its optional equipment are set up as follows:
ADF
Key card counter
Duplo Direct Print System
Tape cluster
Personal computer
Documents prepared on a
personal computer can be
printed on this machine.
PC interface kit is required
to connect this machine to
a personal computer.
Cabinet
Drum unit
18
: Option
Part Names and Their Functions
Printer Appearance
1
q
Before Using This Machine
2
!1
w
e
3
r
!0
t
y
u
i
No.
Name
q
w
e
r
t
y
u
i
o
Document cover
Feed tray descend switch
Feed pressure adjuster lever
Side guides
Feed tray
Support tray
Power switch
Cabinet (Option)
Castor locks
!0
!1
Front cover
Control panel
o
Function
Keeps the document in contact with the document glass plate.
Press to lower the feed tray.
Use to adjust the paper feed pressure.
Slide to match the width of the paper.
Load paper in this tray.
Pull out when using large paper sizes.
Press to switch the power on and off.
Place the printer on this stand.
Lock the printer in position on the floor. Always lock the castor
locks when installing the printer.
Open to replace ink pack and drum unit, etc.
Displays operations and statuses, and sets functions.
Reference
page
32, 38,
103
35
34
34
34
25, 26
—
—
84, 92
22
19
Part Names and Their Functions
Master set lever
When the master set lever is pushed,
the master is pulled in and set.
Master roll
Scanner unit
Master cover
release lever
Master cover
Lever
This lever releases the ink
pack holder.
Front cover
Drum handle
Drum unit
Ink pack
20
Lever
This lever is locks or
unlocks the drum.
Part Names and Their Functions
1
Master ejection
core
Before Using This Machine
2
3
!2
!8
!7
!6
!5
!3
!4
No.
Name
!2
!3
Plate ejection box release lever
JOG switch
!4
!5
!6
!7
!8
Print tray
Paper stopper
Paper stacker guides
Master ejection box
Plate ejection box lid release lever
Function
Press to open the master ejection box.
Press and hold to rotate the drum for a set time. Use to remove
paper jams, etc..
Holds the printed paper.
Slide to match the size of printed paper.
Slide to match the size of printed paper.
Open to replace the master ejection core, etc..
Press to open the top of the master ejection core box. Use when
replacing the master ejection core, etc..
Reference
page
—
—
49
50
49
90
90
21
Part Names and Their Functions
Control Panel
q
w
e
1:1
!7
No.
q
w
e
r
t
y
u
22
Name
“OK” monitor
STD
STD
!6
!5
Function
Flashes to display the content of the trouble and lights to indicated
the part that caused the trouble in the machine.
“ENLARGEMENT” key
Press to set the enlargement ratio.
“100%” key
Press to reset the ration to 100%.
“REDUCTION” key
Press to set the reduction ratio.
100% lamp
Lights when the 100% ratio is selected.
“DOCUMENT MODE
Press to switch between the text mode, text/photograph mode and
SWITCH” key
photograph mode. Each press of this key moves the position of the
lit lamp that indicates the selected document mode.
Document mode indicator lamps The lamp of the selected mode lights.
LCD panel
Displays the number of printed paper.
Also displays an error message when an error occurs.
“FUNCTION SWITCH” key Press to toggle between the normal mode and the function select
mode.
“SELECT” key
Press to select a function.
“TEST PRINT” key
Press to print only one piece of paper for checking the print darkness or printed position.
“PLATEMAKING” key
Press to start platemaking.
Reference
page
99
39
40
39
40
48
48
24, 99
54
54
33
!4
Part Names and Their Functions
r
t
y
1
u
Before Using This Machine
2
3
T
1
2
3
4
5
6
7
8
9
C
0
X
=
!3
!2
!1
No.
i
o
!0
!1
!0
o
i
Name
“STOP” key
“PRINT” key
“ALL CLEAR” key
X
=
key
!2
!3
Key pad
“CLEAR” key
!4
!5
!6
!7
Printing speed indicator lamp
“PRINTING SPEED ADJUSTMENT” keys
“PRINTING POSITION ADJUSTMENT” keys
Printing position indicator lamp
Function
Press to stop printing on the way.
If this key is pressed while the machine is stopped,
the total number of prints and plates will be displayed
on the LCD panel.
Starts printing. This will not start platemaking.
Platemaking will start automatically after the end of
printing if there is a document on the ADF (Option).
Returns the control panel settings to the “Standard
Mode” settings. Press and hold for at least 0.5
seconds.
Press to enter the number of prints and number of sets
for sectional prints.
Use to enter the number of prints.
Press to reset the displayed number of prints to “0”.
Only the number of prints is cleared.
The lamp of the specified printing speed lights.
Press to adjust the printing speed.
Press to adjust the printing position.
The lamp of the specified printing speed lights.
Reference
page
79
33
71
80
80
81
81
23
Part Names and Their Functions
LCD Panel
No.
q
w
24
Name
Print count
Sets
0sht
1set
q
w
Function
Displays the number of prints to be made.
Displays the number of sets to be printed.
Reference
page
33
69
Turning Power ON/OFF
This section describes the operating sequence from turning ON the power switch until the printer is ready to make
prints, and how to turn OFF the printer power.
Turning ON Printer Power
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Before Using This Machine
Connect the power cable to the printer and a
wall outlet.
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Switch the power switch to the “ ” position.
The power turns ON.
The message “SET PRINT PAPER” is displayed on the LCD
panel.
The printer functions are now set in “Standard Mode”
(a page 26).
SET PRINT PAPER
When paper is loaded in the feed tray, the screen shown at
right is displayed.
0sht
1set
When the screen shown at right is displayed, insert a key
card. (a See page 27, “Key Card Counter”.)
SET KEYCARD
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
25
Turning Power ON/OFF
Turning OFF Printer Power
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Switch the power switch to the “ ” position.
The power turns OFF and the display lamps on the control
panel turn OFF.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Standard Mode
When the printer power is first turned ON or
(ALL CLEAR) key is pressed, the functions are reset to
standard mode. The standard mode settings are as follows:
•
•
•
•
•
•
26
Print quantity
Print position
Print speed
Zoom
Document mode
2 IN 1
:0
: Standard lit
: Standard lit
: 100% lights
: Standard lit
: OFF
•
•
•
•
•
•
PLATE SIZE
PLATE DARKNESS
✕94%
2 - up
SHADOW ERASER
MANUAL ZOOM
: DP-22S/A4, DP-24S/B4
: NORMAL
: OFF
: OFF : ADF 2IN1
: OFF
: OFF
Turning Power ON/OFF
Key Card Counter
Available only with Key Card Counter installed
With the key card counter installed, you can control the platemaking and print quantities per person or per
department, etc. See the Instruction Manual for the Key Card Counter for details.
1
■ Inserting a key card
Before Using This Machine
When you turn on the power, the icon shown at right is
displayed if no key card has been inserted in the key card
counter.
2
SET KEYCARD
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
3
Insert a key card in the key card counter.
The printer can now be operated as normal.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
■ Handling key cards
Do not bend or soil a key card.
Keep your key card well away from
magnetic fields.
Do not insert any objects other than
key cards into the key card slot.
27
Document/Printing Paper Specification
Acceptable Documents
■ Document glass plate
• Weight
• Size
: Sheet documents, books, etc, not exceeding 10kg.
: 297mm X 432mm
■ ADF
: 64g/m2 to 128g/m2
: A3 to A5 size
ST to 11x17-in. (ST size in landscape mode: STR cannot be used.)
• Stacking capacity in document tray : 100 sheets (64g/m2)
• Document thickness
• Document size
IMPORTANT
The following types of document cannot be used:
• Documents with large file-binding holes, tears, or missing parts
• Documents with staples or paper clips attached
• Documents with markedly curling ends/sides, or marked folds
• Carbon-backed documents
• Sticky documents
• Highly transparent documents such as OHP film
When ADF is installed:
• To make a new plate from a document from which a plate has already been made, remove
and then reload the document.
• Always use documents of the same size.
• If you load documents of different lengths, the printer may not operate correctly.
Acceptable Printing Paper
Paper thickness
Paper stacking capacity
Paper size
DP-22S
DP-22L
DP-24S
2
45g/m to 210g/m (40kg ~ 180kg)
Feed tray : 1300 sheets (64g/m2 top-grade paper)
Print tray : When a cabinet is used:1300 sheets (64g/m2 top-grade paper)
When the printer is used on a table: 900 sheets (64g/m2 top-grade paper)
Max. 271mm X 382mm
Max. 271mm X 382mm
Max. 271mm X 382mm
(297mm X 432mm)*
(297mm X 432mm)*
(297mm X 432mm)*
Min. 100mm X 150 mm Min. 100mm X 150 mm
Min. 100mm X 150 mm
2
* With paper larger than 297 x 432 → 60sheets/min. DP-24S-standard, DP-22S/L-optional.
Printing area
DP-22S
204mm X 288mm
DP-22L
210mm X 355mm
IMPORTANT
The following types of paper cannot be used.
• Paper with large file-binding holes
• Paper with staples or paper clips attached
• Paper with markedly curling ends/sides, or marked folds
• Carbon-backed paper
• Paper with smaller pieces of glued paper
28
DP-24S
250mm X 355mm
How Platemaking and Printing is Performed
The machine performs two processes: platemaking and printing.
Platemaking
1
In the “platemaking” process, the old master on the drum is removed while the thermal head creates the
scanned image on the new master and transfers it onto the drum.
Thermal head
Before Using This Machine
Master roll
2
Master ejection box
Drum
unit
3
Printing
In the “printing” process, paper separated from the stack by the feeder roller and paper separator unit is
pressed against the drum unit by the press roller. There are small holes over only the image area of the master
that is attached to the drum, and ink that seeps from these holes is transferred to the paper. The paper is then
peeled from the master by the paper stripper finger. The paper is directed onto the paper ejection belt by a fan
unit and discharged from the machine.
Drum unit
Paper stripper finger
Feeder roller
Paper
Ink
Press roller
Paper separator unit
Paper ejection belt
Fan unit
29
30
Chapter
2
Printing Using Basic Functions
This chapter describes how to make prints using the basic functions, including how to load
the document, set zoom ratio, etc.
2
Printing Using Basic Functions
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Basic Printmaking .............................................................................................. 32
Loading and Replacing Paper .......................................................................... 34
Loading Paper .............................................................................................. 34
Adjusting Paper Feed Pressure ................................................................... 35
Loading Documents .......................................................................................... 36
Positioning the Document ............................................................................ 36
Loading Document on Document Glass Plate ............................................. 37
Loading Document in ADF [Available only when ADF installed] .................. 38
Enlargement and Reduction ............................................................................. 39
Enlarging/Reducing from Standard-Size Document to Standard-Size Paper .... 39
94% Reduction ............................................................................................ 40
1% - Step Enlargement and Reducation ..................................................... 42
Selecting Printing Paper Size ........................................................................... 44
Text/Photograph/Text and Photograph Mode ................................................. 47
Print Output ........................................................................................................ 49
Installing Print Tray ....................................................................................... 49
Truing up Printed Pages .............................................................................. 51
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Basic Printmaking
This section describes how to make prints using the basic functions.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a See page 25, “Turning Power ON/OFF”)
Turn ON the power. (a
Tip
• If the power is already ON, press
(ALL CLEAR) key.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a See page 34, “Loading and Replacing Paper.”)
Load paper. (a
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Load the document.
◆If you are positioning the document on the document glass
plate (a See page 37, “Loading Document on Document
Glass Plate”) ...
• Open the document cover.
• Place the document face down on the document
glass plate aligned with the scale.
• Close the document cover.
C
AB
◆If you are loading the document in the optional ADF
(a See page 38, “Loading Document in ADF”) ...
• Adjust the slide guide to the marks for the size of the
document.
• Place the document face up in the document tray.
Scale
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Select the zoom ratio.
The zoom ratio is set to 100%. Press
(ENLARGEMENT)key or
zoom ratio. (a See page 39, “Enlargement and Reduction”.)
(REDUCTION)key to set a desired
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
32
Basic Printmaking
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PLATE MAKING) key.
T
When the plate has been made, one test print is automatically
made.
1
IMPORTANT
• The test print is for verification purposes only
and may be fainter than the final print.
Tip
• You can enter the number of desired prints
before pressing
(PLATE MAKING) key to
immediately print the required number of copies.
2
Use the keypad to specify the number of prints
to make.
Tips
• You can specify up to 9999 prints.
• If you make a mistake entering the number of
prints, press C (CLEAR) key then enter the
correct number.
Printing Using Basic Functions
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
T
1
2
3
4
5
6
7
8
9
C
0
X
=
100sht
Key pad
1set
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PRINT) key.
T
The feed tray raises up to the upper limit and printing starts.
The count displayed on the LCD panel is decremented by
one for each print made.
The printed pages are output to the print tray. (a See page
49, “Print Output”.)
Tip
• To stop a print run, press
restart the print run, press
again.
(STOP) key. To
(PRINT) key
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Repeat steps 3 to 7 to print multiple documents.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
33
Loading and Replacing Paper
Loading Paper
This section describes how to load the printer with paper. You can load approximately 1,300 sheets in this
printer.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the support tray.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Hold the lever and adjust the side guides to the
paper size.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Load a stack of aligned sheets between the
paper guides and press the stack lightly toward
the machine.
IMPORTANT
• You can load the feed tray with approximately
1,300 sheets of 55gsm high-grade paper.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
34
Loading and Replacing Paper
Adjusting Paper Feed Pressure
Adjust the paper feed pressure if an feeding error occurs when using thick or thin paper.
1
■ When no thick paper is fed
Adjust the paper feed pressure adjuster lever to “HIGH”.
■ When two pieces of thin paper are fed
2
Adjust the paper feed pressure adjuster lever to “LOW”.
Printing Using Basic Functions
35
Loading Documents
Positioning the Document
The document can be loaded in the “portrait” or “landscape” position.
IMPORTANT
• A4 and B5-size documents can be loaded in the “portrait” or “landscape” position.
• Use the landscape position when enlarging or reducing from standard-size documents to
standard-size paper, such as A5 to A4.
• A3 and B4 documents can only be loaded in the landscape position.
◆ Document Glass Plate
Portrait (Vertical) Placement
Landscape (Lateral) Placement
AB
C
◆ ADF
Portrait (Vertical) Placement
36
C
AB
Landscape (Lateral) Placement
Loading Documents
Loading Document on Document Glass Plate
Use the platen glass when copying from books, thick documents, or thin documents.
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Gently open the document cover.
2
Printing Using Basic Functions
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Position the document on the document glass
plate.
Place the document face down on the document glass plate,
aligned with the guide.
Scale
IMPORTANT
• When you load a non standard-size document, place it with the center of the document
aligned with the arrow on the guide.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Gently close the document cover.
IMPORTANT
• When you place a thick document such as a
book on the document glass plate, take care
not to force the document cover as this may
damage the document glass plate with a risk
of personal injury.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
37
Loading Documents
Loading Document in ADF
Available only when ADF installed
Load documents that consist of a series of sheets to be printed in the ADF. When one or more documents are
loaded in the ADF, platemaking and printing are automatically repeated until the document tray is empty.
IMPORTANT
• ADF mode is automatically selected when a document is loaded in the ADF. The ADF then
takes priority over the document glass plate in the platemaking process.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Align the document guide with the marks for
the size of document to be loaded in the ADF.
Document Guide
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
AB
Platemaking starts with the top document in the tray.
C
Place the document face-up in the document
tray.
IMPORTANT
• Do not attempt to remove or add to the
documents in the document tray while
platemaking and printing are in progress.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
38
Enlargement and Reduction
Enlarging/Reducing from Standard-Size Document to Standard-Size Paper
You can enlarge or reduce a standard-size document onto standard-size printing paper.
1
The following zoom ratios are available when enlarging or reducing a standard-size document onto standard-size
printing paper.
■ Enlargements
You can enlarge a standard-size document onto standard-size paper using the following zoom ratios:
<DP-24S>
B5 → B4 / A5 → A4 .. 141%
A4 → B4 / A5 → B5 .. 122%
B5 → A4 .................... 115%
2
A4 Printout
A5 Document
Printing Using Basic Functions
● European paper sizes
<DP-22S>
A5 → A4 .................... 141%
A5 → B5 .................... 122%
B5 → A4 .................... 115%
● U.S. paper sizes
<DP-22L>
141%
ST → LTR .................. 129%
121%
■ Reductions
You can reduce a standard-size document onto standard-size paper using the following zoom ratios:
● European paper sizes
<DP-22S>
A4 → B5 ...................... 86%
B4 → A4 / B5 → A5 .... 81%
A3 → A4 / B4 → B5 .... 70%
● U.S. paper sizes
<DP-22L>
LGL→ LTR .................. 77%
LDG→ LGL ................. 74%
LDG→ LTR ................. 64%
<DP-24S>
A3 → B4 / A4→ B5 ..... 86%
B4 → A4 / B5 → A5 .... 81%
A3 → A4 / B4 → B5 .... 70%
A3 Document
A4 Printout
IMPORTANT
• Set the desired zoom ratio before starting the platemaking process.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(ENLARGEMENT) key or
DUCTION) key.
(RE-
1:1
1
4
STD
STD
7
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
39
Enlargement and Reduction
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(ENLARGEMENT) key or
the desired zoom ratio.
(REDUCTION) key several times to display
In about 3 seconds, the screen changes to the number display screen and the zoom ratio is selected.
• Each time
(ENLARGEMENT) key is pressed, the LCD panel display changes as follows: “115%” →
“122%” → “141%” → “115%”...
• Each time
(REDUCTION) key is pressed, the LCD panel display changes as follows: “94%” → “86%” →
“81%” → “70%” → “94%”...
[European paper sizes]
A5➝A4
[U.S. paper sizes]
141%
0sht 1set 141%
ST➝LTR
129%
0sht 1set 129%
Tip
To return to “100%”, use one of the following two methods:
• Press 1 : 1 (100%) key. The 100% indicator lamp lights.
• Press
(ALL CLEAR) key. In this case, all settings are reset to standard mode
(a page 26).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
94% Reduction
In this mode, the copy is printed at 94% the size of the document. When it is not possible to print the edges of
the document image, this mode allows you to make a minor reduciton so that the edges of the image are
included.
IMPORTANT
• Select “94% Reduction” before platemaking.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key several
times to show the screen at right.
3.X94%
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
40
Enlargement and Reduction
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(SELECT) key to display “ON”.
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
“OFF” → “ON” → “OFF”...
ON
1
1
2
3
2
3
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
Printing Using Basic Functions
94% reduction is set.
3.X94%
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
times.
(FUNCTION SWITCH) key several
The number display screen returns and “%” blinks.
Tip
You can cancel 94% reduction using one of the
following two methods.
• Set to “OFF” in the same procedure.
(ALL CLEAR) key. In this case, all
• Press
settings are reset to standard mode
(a page 26).
You can select 94% reduction even when you have selected
other than “100%”. In this case, the zoom ratio will be the
zoom ratio shown on the LCD✕94%.
0sht 1set
1
2
%
3
0sht 1set 141%
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
41
Enlargement and Reduction
1%-Step Enlargement and Reduction
You can set a zoom ratio between 50% and 200% in 1% steps.
IMPORTANT
• Select “1%-Step Enlargement and Reduction” before starting platemaking.
• You cannot select “94% Reduction” at the same time as “1%-Step Enlargement and Reduction”.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a page 32).
Proceed with steps 1 to 4 of the sequence described in “ Basic Printmaking” (a
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press (FUNCTION SWITCH) key several
times to show the screen at right.
7.MANUAL ZOOM
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(SELECT) key several times to display
actual zoom ratio.
100%
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
“OFF” → actual zoom ratio → “OFF” ...
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Use the keypad to enter the scaling ratio.
T
Example:70%
Tip
• You can enter a value for the scaling ratio within
the range 50 to 200%. If you enter a value
smaller than 50%, "50%" will automatically be
selected and displayed, and if you enter a value
larger than 200%, "200%" will automatically be
selected and displayed.
1
2
3
4
5
6
7
8
9
C
0
X
=
Key pad
70%
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
42
Enlargement and Reduction
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
X
=
key.
The scaling ratio is set, and the 100% lamp goes out.
Tip
• To return to "100%", press
C
(CLEAR) key.
1
2
3
4
5
6
7
8
9
C
0
X
=
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
43
Printing Using Basic Functions
a page 32).
Stare platemaking and printing. (a
a See steps 5 to 8 of “ Basic Printmaking” (a
2
Selecting Printing Paper Size
Select a paper size.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
The screen at right appears on the LCD panel.
1.PLATE SIZE
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(SELECT) key several times and display the paper size to be used.
Each time
(SELECT) key is pressed, the display of the LCD panel changes as follows.
◆ European paper sizes
• FOR DP-22S
◆ U.S. paper sizes
• FOR DP-22L
“A4” → “B5” → “A5” → “POST” → “A4”...
• FOR DP-24S
“LG” → “LT” → “ST” → “MAX” →
“POST”→“LG”...
“B4” → “A4” → “B5” → “A5” → “POST” → “B4”...
[European paper sizes]
[U.S. paper sizes]
LT
A4
1
2
3
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
The paper size is set.
1.PLATE SIZE
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
44
Selecting Printing Paper Size
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
times.
(FUNCTION SWITCH) key several
The number display screen returns.
0sht 1set
1
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2
Printing Using Basic Functions
45
Selecting Printing Paper Size
■ When paper of B4 or larger size is used with DP-24S
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key several
times to show the screen at right.
8.PAPER SIZE
1
2
3
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
“LG”.
(SELECT) key several times to display
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
“NORMAL” → “LG” → “NORMAL” ...
LG
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
The paper size is set. (The speed is fixed to 1st and the
printing speed indicator lamp blinks.)
8.PAPER SIZE
Tip
• The printing speed cannot be changed.
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
times.
(FUNCTION SWITCH) key several
The number display screen returns.
0sht 1set
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
46
Text/Photograph/Text and Photograph Mode
This function includes three modes for enhancing text and photographic documents.
■ Text/Photograph/Text and Photograph Mode
In this mode, the print quality is adjusted to match the document.
Text/Photograph
ABCDEFGH
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
tuvwxyz
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
tuvwxyz
ABCDEFGHIJKLNO
PQRSTUVWXYZ
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
1
Photograph
2
Enhances the printing of text documents
Documents suited for text mode:
• Text documents
• Documents that include black and white photos that have already been screen
processed.
Text/Photograph mode: Enhances the printing of documents with both text and photographs.
Documents suited for text/photograph mode:
• Documents with both text and photographs.
Photo mode:
Enhances the printing of the subtle gradations of photographs and light images from
color documents.
Document suited for photo mode:
• Light-colored color documents
• Color photographs
• Documents with non-screened black and white photographs
IMPORTANT
• Select “Text/Photograph/Text and Photograph Mode” before starting platemaking.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
47
Printing Using Basic Functions
Text mode:
Text
ABCDEFGH
Text/Photograph/Txt and Photograph Mode
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a page 32).
Proceed with steps 1 to 4 of the sequence described in “Basic Printmaking” (a
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(DOCUMENT MODE SWITCH) key
to select the desired mode.
Each time
(DOCUMENT MODE SWITCH) key is
pressed, the lit document mode indicator lamp changes as
follows.
“Text” → “Text/Photograph” → “Photograph” → “Text”...
Tip
To return to “Text mode” use one of the following
two methods:
• Press
(DOCUMENT MODE SWITCH) key
to select “Text”.
• Press
(ALL CLEAR) key. In this case, all
settings are reset to standard mode (a page 26).
1:1
1
4
STD
STD
7
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a See steps 5 to 8 of “Basic Printmaking” page 32.)
Start platemaking and printing. (a
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
48
Print Output
This section describes how to install the print tray and remove printed pages from the print tray.
Installing Print Tray
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Remove the print tray.
2
Printing Using Basic Functions
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Install the print tray.
• When you use the printer on a table, install the print tray
into the upper fitting.
(Stacking capacity; 900 sheets, 55 kg, high-grade paper)
• When you use a cabinet (option), install the print tray into
the lower fitting.
(Stacking capacity; 1300 sheets, 55 kg, high-grade paper)
When the printer is used
on a table.
When a cabinet is used.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open out the paper stacker guides.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
49
Print Output
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open out the paper stopper.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Adjust the paper stacker guides and paper
stopper to the size of the printing paper.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
50
Print Output
Truing up Printed Pages
Available only when sorter is installed
Adjust when the edges of the printed pages are not trued up.
1
■ Adjusting jump plate
Adjust the plate according to the paper size.
Ex: Expand the guides fully when using paper with B4
or larger size.
2
Printing Using Basic Functions
■ Truing up printed pages
When using thinner paper, turn the lever up.
When using thicker paper, turn the lever down.
51
Chapter
3
Printing With Various Function
This chapter describes how to make prints using the various printer functions.
3
Printing With Various Functions
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Saving Settings .................................................................................................. 54
Saving Settings ............................................................................................ 54
Retrieving Settings ....................................................................................... 56
Multiple Printing on One Page .......................................................................... 58
2-up Function ............................................................................................... 58
2-in-1 Layout [Available only with ADF installed] ......................................... 61
Book Shadow Eraser Mode ............................................................................... 63
Adjusting Plate Darkness .................................................................................. 65
Sectional Printing .............................................................................................. 67
Sectional Printing ......................................................................................... 67
Sectional Printing (changing print quantity per document) .......................... 71
Dividing Sections with Tape [Available only with Tape Cluster Device] ........ 74
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Saving Settings
You can save and retrieve nine sets of settings for platemaking and printing. The settings are stored in memory even
when the power is turned OFF.
Tips
The following settings are saved:
• Number of prints (including sets)
• Plate size
• Platemaking darkness
• Text/Photo
• Zoom ratio (Fixed zoom ratios only)
• 94% reduction
• Printing speed
• Printing position
Saving Settings
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Confirm that the LCD panel displays the settings you want to store.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key several
times to show the screen at right.
5.MEMORY MODE
1
2
3
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(SELECT) key several times to display
“SAVE”.
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
“RETRIEVE” → “SAVE” → “CANCEL” →
“RETRIEVE”...
SAVE
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
54
Saving Settings
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
The screen at right appears on the LCD panel.
123456789C
1
1
2
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Use the keypad to specify the number you want
to store.
T
3
The settings are stored and the screen in step 3 returns.
2
3
4
5
6
7
8
9
C
0
X
=
1
2
3
4
5
6
7
8
9
C
0
X
=
Key pad
Printing With Various Functions
IMPORTANT
• Any previous settings stored in the memory
channel will be deleted when you save new
settings.
1
Tips
• Press C (CLEAR) key to cancel. The screen in
step 3 returns.
• The numbers already stored are displayed
flashing.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
C
(CLEAR) key.
The number display screen returns.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
55
Saving Settings
Retrieving Settings
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key several
times to show the screen at right.
5.MEMORY MODE
1
2
3
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(SELECT) key several times to display
“RETRIEVE”.
RETRIEVE
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
“RETRIEVE” → “SAVE” → “CANCEL” →
“RETRIEVE”...
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
The screen at right appears on the LCD panel.
123456789C
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Use the keypad to specify the number you want
to recall.
T
The settings are recalled and the screen in step 2 returns.
Tips
• Press C (CLEAR) key to cancel. The screen in
step 2 returns.
• You can recall only the numbers flashing.
1
2
3
4
5
6
7
8
9
C
0
X
=
Key pad
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
56
Saving Settings
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
C
(CLEAR) key.
The number display screen returns.
1
2
3
4
5
6
7
8
9
0
X
C
1
=
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2
3
Printing With Various Functions
57
Multiple Printing on One Page
This mode allows you to print 2 copies of the document on one page.
a page 58)
■ 2-up Function (a
This mode prints 2 copies of the document on one page.
Document
a page 61)
■ 2-in-1 Layout (a
Printout
Available only with ADF installed
This mode prints two different document pages on one page.
Documents
2-up Function
Printout
Available only with ADF installed
This mode prints multiple copies of the document on one page.
• Copying A4 to A3 (2 prints on one page)
Portrait Placement
A4
LT
A3, LDG
A4
LT
A4
LT
Zoom ratio:
100%
IMPORTANT
• Select “2-up Function” before starting platemaking.
• The printable range is slightly smaller than the printing paper.
• You cannot obtain the correct layout if you select the wrong paper size.
58
Multiple Printing on One Page
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a page 32).
Proceed with steps 1 to 4 of the sequence described in “Basic Printmaking” (a
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key several
times to show the screen at right.
1
4.2-UP
1
2
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
“ON”.
3
(SELECT) key several times to display
1
2
3
2
3
Printing With Various Functions
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
"ON" → "OFF" → "ON"...
ON
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
2-up Function is set.
4.2-UP
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
59
Multiple Printing on One Page
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
times.
(FUNCTION SWITCH) key several
The number display screen returns.
Tip
You can cancel 2-up Function using one of the
following two methods.
• Set to “OFF” in the same procedure.
• Press
(ALL CLEAR) key. In this case, all
settings are reset to standard mode
(a page 26).
0sht 1set
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Start platemaking and printing. ( a See stepes 5 to 8 of “Basic Printmaking” page 32).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
60
Multiple Printing on One Page
2-in-1 Layout
Available only with ADF installed
Two-in-one (2-in-1) mode allows you to print two small documents on one page and also easily print for
creating booklets that will be saddle stitched.
When you use 2-in-1 mode, the layout is as follows:
1
2
3
4
2
2
1
Printout1
3
2
Printout2
4
3
5
Printout2
Printout3
3
IMPORTANT
• Select “2-in-1 Layout” before starting platemaking.
• You cannot use 2-in-1 mode unless the optional ADF is installed.
• Always load the documents in the ADF.
• If you are printing the documents at 100%, select a printing paper that is the size of the two
documents.
• When you enlarge or reduce two documents size by side, select a zoom ratio so that the
documents fit exactly on one page.
• Note the following when using 2-in-1 layout mode:
• You must load the document in the ADF in portrait orientation.
• You must select a paper size and zoom ratio that will accommodate two documents.
• Correct layout may not be obtainable with other than standard size papers.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key several
times to show the screen at right.
4.2-UP
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page •••
61
Printing With Various Functions
Documents (odd number)
4
Printout1
Documents (even number)
1
2
3
4
5
1
1
Multiple Printing on One Page
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(SELECT) key several times to display
“ON :: ADF 2IN1”.
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
“OFF :: ADF 2IN1” → “ON :: ADF 2IN1” → “OFF :: ADF
2IN1”...
ON : ADF 2IN1
1
2
3
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
2 IN 1 Function is set.
4.2-UP
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
times.
(FUNCTION SWITCH) key several
The number display screen returns.
Tip
You can cancel 2 IN 1 Function using one of the
following two methods.
• Set to “OFF :: ADF 2IN1” in the same procedure.
(ALL CLEAR) key. In this case, all
• Press
settings are reset to standard mode
(a page 26).
0sht 1set
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
62
Book Shadow Eraser Mode
■ Prints book documents without shadows
This mode erases the shadows caused by the book binding when printing an open spread from a book or other
folded document. It also erases the shadow around the periphery of the document.
1
Printout
With shadow eraser
Document
2
Printout
Without shadow erase
3
Printing With Various Functions
IMPORTANT
• Select “Book Shadow Eraser Mode” before starting platemaking.
• When you select “No shadow erase”, the shadow is erased from approximately 3mm
around the periphery of the document.
• When you select “Shadow erase”, the machine reproduces the document as follows.
6mm
6mm
15mm
6mm
6mm
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a page 32.)
Proceed with steps 1 to 4 of the sequence described in “Basic Printmaking” (a
Place the document on the platen glass.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key several
times to show the screen at right.
6.SHADOW ERASER
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
63
Book Shadow Eraser Mode
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(SELECT) key several times and
display the document size to be used.
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
<DP-22S/24S>
"OFF" → "A3" → "B4" → "A4" → "B5" → "A5" →
"POST" → "OFF"...
<DP-22L>
"OFF" → "WLT" → "10X14" → "LG" → "LT" → "ST" →
"POST" → "OFF"...
POST
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
Book Shadow Eraser Mode is set.
6.SHADOW ERASER
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
times.
(FUNCTION SWITCH) key several
The number display screen returns.
Tip
You can cancel Book Shadow Eraser Mode using
one of the following two methods.
• Set to “OFF” in the same procedure.
• Press
(ALL CLEAR) key. In this case, all
settings are reset to standard mode
(a page 26).
0sht 1set
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Start platemaking and printing. ( a See stepes 5 to 8 of “Basic Printmaking” page 32).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
64
Adjusting Plate Darkness
The plate darkness (the level at which black and white are differentiated) can be adjusted in 3 steps.
Make the plate more “dark” if the document is light, or “light” if the document is dark.
IMPORTANT
• Set the “Plate Darkness” before making the plate.
• If you adjust the plate darkness, you must repeat the platemaking process before making
prints.
1
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key several
times to show the screen at right.
2.PLATE DARKNESS
3
2
3
2
3
Printing With Various Functions
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
(SELECT) key several times to display
Press
the desired plate darkness.
Each time
(SELECT) key is pressed, the display of the
LCD panel changes as follows.
“NORMAL” → “DARK” → “LIGHT” → “NORMAL”...
DARK
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(FUNCTION SWITCH) key.
The plate darkness is selected.
2.PLATE DARKNESS
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
65
Adjusting Plate Darkness
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
times.
(FUNCTION SWITCH) key several
The number display screen returns.
Tip
There are two ways to return the darkness to
“NORMAL” as follows.
• Set the darkness to “NORMAL” in the same
procedure.
• Press
(ALL CLEAR) key. In this case, all
settings are reset to standard mode
(a page 26).
0sht 1set
1
2
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
66
Sectional Printing
You can print the specified number of sets of prints in each set.
a page 67)
■ Sectional Printing (a
The machine stops after each set of prints.
1st set
5 copies x 2 sets
Document
1
1
2nd set
3 copies x 4 sets
1
1
1
3rd set
2 copies x 5 sets
2
1
1
1
1
1
1
1
3
1
a page 71)
■ Changing Print Quantity per Document (a
This function changes the number of prints made from each document.
1
1st document
5 copies x 2 sets
1
2
2nd document
3 copies x 4 sets
2
1
3rd document
2 copies x 5 sets
Printing With Various Functions
Documents
3
2
3
3
2
3
2
3
3
Sectional Printing
In this mode, each set comprises the specified number of prints and the machine prints the specified number of
sets, stopping after each set.
You can enter up to 15 groups of the specified number of prints x number of sets.
IMPORTANT
• Select “Sectional Printing” after platemaking.
67
Sectional Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a page 32).
Proceed with steps 1 to 5 of the sequence described in “Basic Printmaking” (a
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press C (CLEAR) key to clear the number
display.
1
2
3
4
5
6
7
8
9
C
0
X
=
0sht
1set
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Use the keypad to enter the number of prints.
T
Example: 25
Tip
• If you make a mistake, start over again by press
C (CLEAR) key and start from the beginning.
When you press C (CLEAR) key, both the
number of prints and the number of sets are
cancelled.
1
2
3
4
5
6
7
8
9
C
0
X
=
25sht
Key pad
1set
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
68
Sectional Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
X
=
key.
The number of prints is set.
1
2
3
4
5
6
7
8
9
0
X
C
1
=
2
0set
25sht
3set
3
Printing With Various Functions
25sht
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Use the keypad to enter the number of sets.
Example: 3 sets
Tip
• If you make a mistake, start over again by press
C (CLEAR) key and start from the beginning.
When you press C (CLEAR) key, both the
number of prints and the number of sets are
cancelled.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
X
=
key.
1
2
3
4
5
6
7
8
9
C
0
X
=
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Repeat steps 2 to 5.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
69
Sectional Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PRINT) key.
T
The print runs starts from the last-entered set, and stops after
the first set of printouts.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Collate by inserting a piece of paper that acts as a marker or by removing the whole
set from the machine.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PRINT) key.
The print run starts.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Repeat steps 8 and 9 until all entered sets have been printed.
IMPORTANT
•
(PLATE MAKING) key will not work until all the sets have been printed.
(STOP) key then C (CLEAR) key to abort the print run.
• Press
Tip
• When two or more documents are loaded in the ADF, platemaking of the following documents
and printing will automatically start after the entire printing is completed.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
70
Sectional Printing
Sectional Printing (changing print quantity per document)
You can change the number of prints made from each document. You can separate the number of prints for up
to 15 documents.
IMPORTANT
• Select “Sectional Printing” before starting platemaking.
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press C (CLEAR) key to clear the number
display.
1
2
3
4
5
6
7
8
9
C
0
X
=
3
Printing With Various Functions
0sht
2
1set
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
X
=
key.
“sht” and “set” begin to flash and the number setting by
document mode returns.
1
2
3
4
5
6
7
8
9
C
0
X
=
0sht
1set
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
71
Sectional Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Use the keypad to enter the number of prints.
T
Example: 25
Tip
• If you make a mistake, start over again by press
C (CLEAR) key and start from the beginning.
When you press C (CLEAR) key, both the
number of prints and the number of sets are
cancelled.
1
2
3
4
5
6
7
8
9
C
0
X
=
25sht
Key pad
1set
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
X
=
key.
The number of prints is set.
1
2
3
4
5
6
7
8
9
C
0
X
=
25sht
0set
25sht
3set
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Use the keypad to enter the number of sets.
Example: 3 sets
Tip
• If you make a mistake, start over again by press
C (CLEAR) key and start from the beginning.
When you press C (CLEAR) key, both the
number of prints and the number of sets are
cancelled.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
72
Sectional Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
X
=
key.
1
2
3
4
5
6
7
8
9
0
X
C
1
=
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2
Repeat steps 2 to 6.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Proceed with steps 2 and 4 of the sequence described in “Basic Printmaking”
a page 32).
(a
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PLATE MAKING) key.
T
Platemaking starts.
IMPORTANT
• Plate making and printing starts from the lastentered print and set quantities.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
After the first document is printed, platemaking of the next document and printing
will automatically start.
Tip
• Using the optional tape cluster you can successively perform the platemaking and collating of
prints of multiple documents.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
73
Printing With Various Functions
IMPORTANT
• When loading document, load the document for the first-entered number of prints and sets
uppermost and the document for the last-entered number of prints and sets at the bottom.
3
Sectional Printing
Dividing Sections with Tape
Available only with Tape Cluster Device
Only the specified number of sets is printed with the specified number of prints taken as one set. Paper tape is
inserted when printing of each set is completed.
You can enter up to 15 groups of number of prints x number of sets.
IMPORTANT
• The optional tape cluster is required for dividing sections with tape.
• You can select “Sectional Printing” after platemaking.
• When the optional tape cluster is installed, you cannot stop printing after each section.
Tip
• The length of the paper tape separating groups is longer than the paper tape separating sets.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the tape cluster cover.
Cover
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Insert the tape while checking for the direction of the tape roll.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Insert the tape while lifting the two levers up.
Levers
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
74
Sectional Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Leave end of tape approximately 1 cm out.
1
1cm
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2
Close the cover.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
3
Tip
• The paper tapes are inserted so that the length of the paper tape separating sets is longer
than the paper tape separating groups.
Printing With Various Functions
75
Chapter
4
Miscellaneous Functions
This chapter describes miscellaneous functions such as the confidential safeguard function,
and the print speed and print position adjustments.
4
Miscellaneous Functions
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Confidential Safeguard Function ..................................................................... 78
Total Counter Display Function ........................................................................ 79
Print Speed Adjustment Function .................................................................... 80
Printing Position Adjustment Function ........................................................... 81
On-Line Print Function [Available Only With Interface Kit Installed] ............ 82
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Confidential Safeguard Function
The confidential safeguard function, which prevents printing unless platemaking has been completed, is a simple means
of prohibiting others from printing sensitive documents.
IMPORTANT
• When the Confidential Safeguard function is ON, printing cannot be performed with
(PRINT) or
(TEST PRINT) keys. Other operations can be performed as normal.
• Turning the power OFF does not turn the Confidential Safeguard function OFF.
• Once platemaking is carried out, the Confidential Safeguard function is cleared.
• Platemaking still functions even if the Confidential Safeguard function in ON.
T
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(STOP) key while also pressing
(CLEAR) key.
C
The machine beeps and the Confidential Safeguard function
is activated.
T
1
2
3
4
5
6
7
8
9
C
0
X
=
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PRINT) key or
T
(TEST PRINT) key to check that no print is made.
Tips
• The message “PLS PLATE MAKING” is displayed on the LCD panel and the machine will
(PRINT) or
not print when you press
(TEST PRINT) key while the Confidential
Safeguard function is ON.
• To cancel the Confidential Safeguard function,
press
(PLATE MAKING) key to start
platemaking.
T
PLS PLATE MAKING
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
78
Total Counter Display Function
This function displays the total numbers of prints and plates on the LCD panel.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Check that the machine is not printing.
IMPORTANT
• If the machine is printing, press
1
(STOP) key to stop the print run.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(STOP) key.
2
T
The total print and plate counts are displayed while you press
and hold
(STOP) key.
The number of prints is displayed on the left side and the
number of plates on the right side of the LCD panel.
Example: In this example, the total number of prints is
455132, and the total number of plates is 245.
4
245
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
79
Miscellaneous Functions
P 455132 F
Print Speed Adjustment Function
The printing speed can be selected from among 60 pages per minute, 80 pages per minute and 120 pages per minute.
The default setting when the power is turned ON is about 80 pages per minute.
Tips
• Paper jams may become more frequent and the paper stacking deteriorate at high and low
speeds with certain types of paper and with certain images. Satisfactory performance of
printing can be obtained by adjusting the printing speed.
• The prints may be slightly lighter at high printing speeds and slightly darker at slow printing
speeds.
• You can adjust the printing speed while the machine is printing.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
or
1:1
keys to adjust the speed.
Press
key to decelerate printing. The printing speed
indicator lamp moves to the left.
Press
key to accelerate printing. The printing speed
indicator lamp moves to the right.
STD
STD
“PRINTING SPEED
ADJUSTMENT key”
Tip
To return to the default setting (about 80 pages
per minute), use one of the following two methods:
• Press
orr
key repeatedly until the center
speed lamp is lit.
• Press
(ALL CLEAR) key. In this case, all
settings are reset to standard mode (a page
(ALL CLEAR) key while
26). Do not press
the machine is printing.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
80
Printing Position Adjustment Function
After platemaking has finished, you can fine-tune the position of the image (in the horizontal direction) within ±10mm.
Tip
• You can adjust the printing position while the machine is printing.
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
or
“PRINTING POSITION ADJUSTMENT” keys to adjust the printing position.
Pressing and holding
or
(PRINTING POSITION
ADJUSTMENT) keys continuously adjusts the printing
position.
The printing position indicator lamps change for each
approximately 3mm change in the printing position.
1:1
STD
2
STD
●To move the printing position to the left, press
key.
The printing position indicator lamp moves to the left.
Paper
Direction of paper
movement
4
Image
Miscellaneous Functions
●To move the printing position to the right, press
key.
The printing position indicator lamp moves to the right.
1:1
Paper
Direction of paper
movement
STD
STD
Image
Tip
To return to the default settings, use one of the
following two methods:
• Press
or
key repeatedly until the
center printing position indicator lamp is lit.
• Press
(ALL CLEAR) key. In this case, all
settings are reset to standard mode (a page
26). Do not press
(ALL CLEAR) key
while the machine is printing.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
81
On-Line Print Function
Available Only With Interface Kit Installed
This function allows you to make prints of documents directly from on-line data from personal computers.
IMPORTANT
• PC interface kit is required to connect this machine to a personal computer.
• Please contact your service person on information regarding installation and settings.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Check that the top menu is displayed.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a See page 44, “Selecting Printing Paper Size”.)
Set the size of the printing paper. (a
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Use the print command of the computer applications according to the manual.
Platemaking and printing start automatically.
Tip
When platemaking ends and printing starts, you can again use the keys on the control panel.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
82
Chapter
5
Replacing Consumables
This chapter describes how to supply paper, ink pack, and other consumables.
5
Replacing Consumables
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Replacing the Ink Pack ...................................................................................... 84
Replacing the Master Roll ................................................................................. 87
Replacing the Master Ejection Core ................................................................. 90
Replacing the Drum Unit ................................................................................... 92
Removing the Drum Unit ............................................................................. 92
Installing the Drum Unit ............................................................................... 94
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Replacing the Ink Pack
The message “EXCHANGE INK” is displayed on the LCD panel when the remaining ink is low. Replace the ink pack
using the following procedure.
EXCHANGE INK
IMPORTANT
• Only use ink packs designed for this machine.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the front cover.
Front cover
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Lever
Grasp the lever and pull it toward you.
Ink pack
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Lift out the empty ink pack.
Ink pack
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
84
Replacing the Ink Pack
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Remove the cap from a new ink pack.
Ink pack
IMPORTANT
• Do not leave an ink pack uncapped for longer
than necessary.
1
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Insert the ink pack so that the groove on the lip
fits onto the “U” groove of the holder.
Ink pack
Ink pack
“U” groove of holder
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Push the ink pack in to the set line on the ink
pack.
Set line
5
Replacing Consumables
Set line
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the back of the holder in with the palm of
your hand.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
85
Replacing the Ink Pack
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Close the front cover.
Front cover
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
86
Replacing the Master Roll
The message “ROLL-MASTER END” is displayed on the LCD panel when the master roll is used up. Replace the
master roll using the following procedure.
ROLL-MASTER END
1
2
IMPORTANT
• Only use a master roll designed for use in this machine.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Slide the scanner unit.
Scanner unit
IMPORTANT
• Do not touch the heat generator of thermal
head. Doing so may cause damages, leading
to a malfunction of plate making.
5
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the master cover ralease lever.
The master cover will open up.
Master cover
release lever
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Lift out the master roll.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page •••
87
Replacing Consumables
Master roll
Master cover
Replacing the Master Roll
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Take out a new master roll from the bag.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Set the master roll in the direction as shown in
the illustration at right.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Pull out the master , and insert the master
aligned with the loading line under the guide
panel until it contacts the roller.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Close the master cover.
Master cover
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Push the master set lever.
The master is pulled in.
Master
set lever
IMPORTANT
• If the master is not pulled in open the master
cover, and gently press in as far as possible
to set again.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
88
Replacing the Master Roll
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Make sure that the leading edge of the master is
protruding from the inner side of the master
cover.
1
IMPORTANT
• If the master cannot be set correctly, its
leading edge will not be visible. Open the
master cover, and set again.
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Slide the scanner unit and return it to the original position.
WARNING
• Do not remove the cover affixed with Warning
Label 1.
• Personnel may be injured by the movable
cutter inside the machine.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5
Replacing Consumables
89
Replacing the Master Ejection Core
The message “EXCHG. EJECT-CORE” is displayed on the LCD panel when the master ejection core is full.
Remove the master ejection core using the following procedure:
EXCHG.EJECT-CORE
IMPORTANT
• Use only a master ejection core designed for use in this machine.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the plate ejection box release lever to open
the master ejection box.
Plate ejection box release lever
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the master ejection box until it stops.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the cover while pressing and holding the
plate ejection box lid release lever.
Plate ejection box
lid release lever
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
90
Replacing the Master Ejection Core
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Holding the edges of the master ejection core,
pull out the core and discard it.
1
IMPORTANT
• Ink adheres to the master ejection core. Take
care to prevent ink from getting onto your
clothing.
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Insert a new master ejection core.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Gently close the master ejection box cover,
pressing it until it locks.
5
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Replacing Consumables
Close the master ejection box, pressing it until it
locks.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
91
Replacing the Drum Unit
Removing the Drum Unit
WARNING
• Avoid pressing and damaging the drum surface with fingers etc. It can stain your clothes,
and the warp in the drum surface may cause bad prints.
• Always place the drum unit on flat and stable surface. Otherwise, the drum surface may
be damaged or warped and may cause bad prints.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press and hold the JOG switch until the drum
comes to a stop with a beep.
JOG switch
WARNING
• Do not touch the drum or rollers when you
operate the JOG switch.
• Do not put your hands or fingers inside the
machine while it is operating. Your hands may
be pulled in or nipped.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the front cover toward you.
Front cover
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Lift the drum securing lever toward you and,
holding it there, then pull out the drum handle
straight toward you until it stops.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
92
Drum handle
Drum securing lever
Replacing the Drum Unit
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Hold the handle on the far end of the drum, and
lift the front end of the drum slightly to pull the
drum toward you.
Handle for end
of drum
1
IMPORTANT
• Do not touch the drum surface. Ink may
transfer to your clothes.
• Hold the drum level and place it on a flat,
solid surface.
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5
Replacing Consumables
93
Replacing the Drum Unit
Installing the Drum Unit
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Hold the drum level and place the drum guide
roller onto the rail in the machine.
Roller
Rail
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Release the handle at the far end of the drum
and press the drum in about 10cm while lifting
up the front end slightly.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Hold the drum level and press it in gently until it comes to a stop.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Lift the drum securing lever toward you while
pressing the drum in.
Lever
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
94
Replacing the Drum Unit
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Lower the lever.
Lever
1
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Close the front cover.
Front cover
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5
Replacing Consumables
95
Chapter
6
Troubleshooting
This chapter describes how to remove paper jams and what to do when error messages are
displayed.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Countermeasures to Troubles .......................................................................... 98
6
Power Does Not Turn ON ............................................................................ 98
Error Messages .................................................................................................. 99
Supplying or Changing Paper While Printing ............................................... 103
If Paper Runs Out During Printing ............................................................. 103
Adding Paper While Printing ...................................................................... 103
Changing Paper Selection While Printing .................................................. 105
Paper Jams ....................................................................................................... 107
When “PAPER LEFT JAM” is Displayed (Feed Tray) ................................ 107
When “PAPER RIGHT JAM” is Displayed (Print Tray) ............................... 108
When “MAST.EJECT ERROR” is Displayed ................................................... 111
When “MASTER SET MISS” is Displayed....................................................... 114
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Troubleshooting
Platemaking/Printing is Not Possible ........................................................... 98
Countermeasures to Troubles
Power Does Not Turn ON
If the power does not turn ON, check the following.
THE MACHINE DOESN'T TURN ON.
IS POWER PLUG INSERTED?
YES
NO
Insert the power
plug securely.
IS POWER SWITCH ON?
YES
NO
Turn the power switch ON.
Please contact your service person.
Platemaking/Printing is Not Possible
If platemaking/printing is not possible, check the following.
IS THERE A MESSAGE DISPLAYED
ON ERROR DISPLAY PANEL?
YES
NO
See "Error Messages" on page 99.
Please contact your service person.
98
Error Messages
Message
Countermeasure
1
There is no paper in the feed tray.
Load the feed tray with printing paper.
SET PRINT PAPER
2
There is no ink.
Replace the old ink pack with a new one.
(a For details, see page 84, “Replacing the Ink Pack”.)
EXCHANGE INK
There is no master.
Replace the master roll with a new one.
(a For details, see page 87, “Replacing the Master Roll”.)
ROLL-MASTER END
The master ejection core is full.
Replace the core with a new one. (a For details, see page 90,
“Replacing the Master Ejection Core”.)
EXCHG.EJECT-CORE
6
Troubleshooting
There is no drum.
Install a drum in the machine. (a For details, see page 92,
“Replacing the Drum Unit”.)
DRUM NOT SET
The front cover is open.
Close the front cover.
FRONT COVER OPEN
The upper cover is open.
Close the upper cover.
DOC.TRAY OPEN
99
Error Messages
Message
Countermeasure
A paper jam has occurred in the feed tray.
Remove the jammed paper. (a For details, see page 107,
“When ‘PAPER LEFT JAM’ is displayed (Feed Tray)”.)
PAPER LEFT JAM
PAPER RIGHT JAM
A paper jam has occurred on the print tray side.
Inspect the print tray side and remove the jammed paper. (a
For details, see page 108, “When ‘PAPER RIGHT JAM’ is
displayed (Print Tray)”.)
There is an old master on the drum.
Remove all the masters from the drum. (a For details, see
page 111, “When ‘MAST.EJECT ERROR’ is Displayed”.)
MAST.EJECT ERROR
MASTER SET MISS
There is an error during master setting.
Open the top cover and remove the master that is left in the plate
feeder. (a For details, see page 114, “When ‘MASTER SET
MISS’ is Displayed”.)
The scanner cover is open.
Close the sucanner cover.
SCANNER OPEN
The document is jammed on the ADF.
Remove the jammed document in accordance with the ADF
instruction manual.
DOCUMENT JAM
Insert the key card into the key card counter.
For details, see the Key Card Counter Instruction Manual.
SET KEYCARD
100
Error Messages
Message
PLS PLATE MAKING
-- PRINTING --
Countermeasure
1
Cannot print.
This message is displayed just after the master setting error or
plate ejection error occurs.
It is also displayed if you
(PRINT) key or
(TEST
PRINT) key without making a plate while the confidential
safeguard function is activated. Make a plate first.
T
Printing is not complete.
Either press
(PRINT) key to resume printing or press
(CLEAR) key to clear the counter.
2
C
A plate is being made.
Wait until it is completed.
-- SCANNING --
ON-LINE ERROR
An error occurs on-line.
Turn the power OFF once and check the connector for connection, then make a plate on-line. If the same display appears,
turn the power OFF and contact servicepersons.
6
Troubleshooting
There is no document.
Set a document.
NO DOCUMENT
PLEASE WAIT
The printer is not ready.
Wait a while with the power turned ON.If this message does
not disappear after several minutes, turn the power OFF and
contact servicepersons.
The master is not set correctly.
Set the master again.
RESET MAST.ROLL
101
Error Messages
Message
SERVICE CALL
This message blinks alternately with the
message “Exxx”.
102
Countermeasure
Turn the power OFF once and turn the power ON again in
several seconds. If the same display appears, make a memo of
the message “Exxx” and contact servicepersons.
Supplying or Changing Paper While Printing
If Paper Runs Out During Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
If paper runs out during printing, printing
stops and the feed tray is lowered automatically.
SET PRINT PAPER
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
a See page 34, “Loading and Replacing Paper”.)
Load paper (a
1
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PRINT) key.
T
Printing resumes.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Adding Paper While Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(STOP) key.
6
T
Printing stops.
Troubleshooting
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the feed tray descend switch continuously.
Release the switch when the feed tray reasches
the proper height.
Feed tray descend switch
The feed tray will stop.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
103
Supplying or Changing Paper While Printing
IMPORTANT
• If the sheet is still in the feed roller ring, pull it
out and align it with the stack.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Align the stack to be added and place it on top
of the existing stack. Press the stack lightly
toward the machine.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PRINT) key.
T
The feed tray will rise automatically and printing will
resume.
Tip
• When you press
(STOP) key, printing stops.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
104
Supplying or Changing Paper While Printing
Changing Paper Selection While Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(STOP) key.
1
T
Printing stops.
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the feed tray descend switch continuously.
Release the switch when the paper tray is at the
proper height.
Feed tray descend switch
The feed tray will stop.
IMPORTANT
• If the sheet is still in the feed roller ring, pull it
out and align it with the stack.
6
Troubleshooting
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Remove paper from the feed tray.
The feed tray will automatically descend.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
105
Supplying or Changing Paper While Printing
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
When the feed tray comes to a stop, reset the paper size.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PRINT) key.
T
The feed tray will rise automatically and printing will
resume.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
106
Paper Jams
When “PAPER LEFT JAM” is Displayed (Feed Tray)
When a paper jam occurs in the feed tray, the message “PAPER LEFT JAM” is displayed on the LCD. Follow
the procedure below to remove the jammed paper.
1
PAPER LEFT JAM
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Switch to lower the feed tray slightly.
Feed tray descend switch
The feed tray is lowered for the time that the switch is
pressed.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Pull out the jammed paper as shown in the
diagram.
6
Troubleshooting
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the JOG switch until the drum comes to
a stop with a beep.
JOG switch
WARNING
• Do not touch the drum or rollers when you
operate the jog switch.
• Do not put hands inside machine while it is
operating. Hands could get caught up or
crushed.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
107
Paper Jams
When “PAPER RIGHT JAM” is Displayed (Print Tray)
When a paper jams in the print tray, “PAPER RIGHT JAM” is displayed on the LCD panel. Follow the
procedure below to remove the jammed paper.
PAPER RIGHT JAM
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the plate ejection box release lever to open
the master ejection box.
Plate ejection box release lever
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the master ejection box until it stops.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Remove the jammed paper.
Press the JOG switch to eject the partially printed paper.
JOG switch
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
108
Paper Jams
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Close the master ejection box, pressing it until it
locks.
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2
■ Paper Adhering to Drum
If paper has adhered to the drum, follow the procedure below to remove it.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the plate ejection box release lever to open
the master ejection box.
Plate ejection box release lever
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the master ejection box until it stops.
6
Troubleshooting
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the JOG switch to find the edge of the
paper, then stop the drum at the position shown
in the diagram.
Paper edge
WARNING
• Do not touch the drum or rollers when you
operate the JOG switch.
• Do not put your hands inside the machine
while it is operating. Your hands may be
pulled in or nipped.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page •••
109
Paper Jams
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Peel off the edge of the paper from the drum.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Pull the paper toward the ejection side while
pressing the JOG switch to peel the paper off.
IMPORTANT
• Make sure that the peeled paper does not
stick to your clothing.
JOG switch
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Hold the JOG switch down until the drum
comes to a stop with a beep.
JOG switch
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Close the master ejection box, pressing it until it
locks.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Make another plate.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
110
When “MAST.EJECT ERROR” is Displayed
When and old master remains on the drum, “MAST.EJECT ERROR” is displayed on the LCD panel. Remove it by
following the procedure below.
MAST.EJECT ERROR
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the plate ejection box release lever to open
the master ejection box.
Plate ejection box release lever
1
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Open the master ejection box until it stops.
6
Troubleshooting
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the JOG switch to find the edge of the
paper, then stop the drum at the position shown
in the diagram.
WARNING
• Do not touch the drum or rollers when you
operate the JOG switch.
• Do not put your hands inside the machine
while it is operating. Your hands may be
pulled in or nipped.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
111
When “MAST.EJECT ERROR” is Displayed
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Lift the lever toward you.
The master clamp opens and the edge of the master will be
released from the clamp. If the master is stuck, release it
manually.
Master clamp
Lever
Master
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Return the lever.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Pull the front end of the master toward you and
press the JOG switch intermittently.
Hold the switch down until the master peels off.
IMPORTANT
• Discard the old master, making sure that it
does not touch your clothing.
JOG switch
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Hold the JOG switch down until the drum comes to a stop with a beep.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Close the master ejection box, pressing it until it
locks.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
112
When “MAST.EJECT ERROR” is Displayed
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(STOP) key.
T
The message is deleted.
1
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Make another plate.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
6
Troubleshooting
113
When “PLATE EJECTION ERROR” is Displayed
When “MASTER SET MISS” is Displayed
The message “MASTER SET MISS” is displayed on the LCD panel. Remove the master and remake the plate by
following the procedure below.
MASTER SET MISS
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Slide the scanner unit.
Scanner unit
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press the master cover ralease lever.
The master cover will open up.
Master cover
release lever
Master roll
Master cover
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Remove the master left in the master feeder.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
114
When “MASTER SET MISS” is Displayed
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Lift out the master roll.
1
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Set the master roll in the direction as shown in
the illustration at right.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Pull out the master , and insert the master
aligned with the loading line under the guide
panel until it contacts the roller.
6
Troubleshooting
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Close the master cover.
Master cover
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continue Page • • •
115
When “MASTER SET MISS” is Displayed
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Push the master set lever.
The master is pulled in.
Master
set lever
IMPORTANT
• If the master is not pulled in open the master
cover, and gently press in as far as possible
to set again.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Make sure that the leading edge of the master is
protruding from the inner side of the master
cover.
IMPORTANT
• If the master cannot be set correctly, its
leading edge will not be visible. Open the
master cover, and set again.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Slide the scanner unit and return it to the original position.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Check that the error message is deleted.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Make a new plate and start printing.
IMPORTANT
• The message “PLS PLATE MAKING” is displayed on the LCD panel when
is pressed without platemaking being carried out.
(PRINT) key
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
116
Chapter
7
Specifications and Maintenance
This chapter lists the machine specifications and describes maintenance, etc.
7
Specifications .................................................................................................... 118
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Specifications and Maintenance
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Specifications
Product name/model No.
Model
Duprinter DP-22S
Table top
Platemaking method
Platemaking time
Thermal digital platemaking
25 seconds (A4, same size)
Resolution
Scanning method
Printing method
300 dpi (Main scanning direction) x 600 dpi (Sub scanning direction)
Fixed document
Stencil print
Document type
Document size
Sheet, book (10kg max.)
297 x 432mm max.
100 x 148mm min.
Printing area
Feeding capacity
204 x 288mm
210 x 355mm
1300 sheets (64gsm, 55kg, high-grade paper)
Stacking capacity
When a cabinet is used : 1300 sheets (64gsm, 55kg, high-grade paper)
When the printer is used on a table : 900 sheets (64gsm, 55kg, high-grade paper)
Max. 271mm x 382mm
Max. 271mm x 382mm
Max. 271mm x 382mm
* (297mm x 432mm)
Min. 100mm x 150mm
Min. 100mm x 150mm
Min. 100mm x 150mm
45gsm to 210gsm (40kg to 180kg)
Paper size
Paper thickness
Printing speed
Print enlargement/reduction
European size
U.S. size
Duprinter DP-22L
Duprinter DP-24S
250 x 355mm
120 pages per minute (60 to 120 pages per minute, 3 step adjustment)
Same size (100%)
Fixed zoom ratios: 70, 81, 86, 115, 122, and 141%
Print with border: 94%
Zoom: 50 to 200%
Same size (100%)
Fixed zoom ratios: 64, 74, 77, 121, 129, and 141%
Print with border: 94%
Zoom: 50 to 200%
Image modes
Vertical: ±15mm (In LG mode: A3 size: ±10mm, Inch size: ±5mm)
Horizontal: ±10mm (Paper with the size of 297mm x 420mm or more: ±5mm)
Text mode/Photograph mode/Text and photograph mode
Darkness adjustment
Ink supply method
Plate darkness: 3 steps
Complete automatic control (600ml)
Color printing
Master feeder
Plate ejection
Drum unit exchange method
Roll master automatic feed
Complete automatic ejection plate rolling method
LCD panel
Miscellaneous standard
Light and compact type LCD
OK monitor
Confidential Safeguard Function
Entry of different number of prints or sets
Special functions
Memory Function
2-up Function (2-in-1 Layout when
using ADF)
Options
Drum unit
Key card counter (built-in type)
Tape cluster
PC interface kit II
Printing position adjustment
Book Shadow Eraser Mode
Long Mode (DP-24S : Standard,
DP-22S/22L Optional)
Manual Zoom (50-200%)
Cabinet
ADF (Automatic Document Feeder)
Long Paper Unit
* With paper larger than 271 x 432 → 60sheets/min. DP-24S-standard, DP-22S/L-optional.
118
Specifications
Product name/model No.
Power source
120 VAC model
Duprinter DP-22S
Duprinter DP-22L
Duprinter DP-24S
120VAC 60 Hz, 4 A
230 VAC model
Size
230VAC 50 Hz, 2 A
In use: 1270mm (W) x 615mm (D) x 666mm (H)
In storage: 695mm (W) x 615mm (D) x 666mm (H)
<When ADF is installed>
In use: 1270mm (W) x 615mm (D) x 805mm (H)
In storage: 695mm (W) x 615mm (D) x 805mm (H)
Weight
Operating temperature
PC interface kit
Machine 73kg
10°C to 30°C
The printer driver must be installed in the PC.
• Windows95/98 compatibility
• WindowsNT 4.0/2000 compatibility
• Macintosh compatibility
(SYSTEM 7 or later, MAC OS 7.6.1 or later)
I/F board in main unit
1
2
Note Specifications subject to change without prior notice.
7
Specifications and Maintenance
119
120
Appendix
This section contains an index and quick reference diagrams for basic operations.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Quick Operation Guide .................................................................................... 124
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Appendix
Index.................................................................................................................. 122
Index
A
Acceptable Documents ............................................... 28
Acceptable Printing Paper .......................................... 28
Adding Paper While Printing .................................... 103
ADF ............................................................................ 18
Adjusting Plate Darkness ........................................... 65
ALL CLEAR key ........................................................ 23
Installing Print Tray .................................................... 49
J
JOG switch ........................... 21, 92, 107, 108, 110, 112
K
Key Card ..................................................................... 27
Key Card counter .................................................. 18, 27
Key pad ....................................................................... 23
B
Basic Printmaking ...................................................... 32
Book Shadow Eraser Mode ........................................ 63
C
Cabinet .................................................................. 18, 19
castor locks ................................................................. 19
Changing Paper Selection While Printing ................ 105
Changing Print Quantitiy per Document .................... 71
CLEAR key ................................................................ 23
control panel ............................................................... 22
Conventions Used in This Manual .............................. 15
D
Dividing Sections with Tape ....................................... 74
Document guide .............................................. 19, 32, 37
Document tray ...................................................... 19, 36
Document/Printing Paper Specification ..................... 28
drum handle ................................................................ 20
drum unit .................................................. 18, 20, 29, 92
Duplo Direct Print System .......................................... 18
L
Lateral Placement ....................................................... 36
LCD panel ............................................................ 22, 24
Loading and Replacing Paper ..................................... 34
Loading Documents .................................................... 36
M
Maintenance ............................................................... 13
master ................................................................. 90, 114
master clamp ............................................................. 112
master cover .......................................................... 20, 87
master ejection box ......................... 21, 29, 90, 108, 111
Master Ejection Core ............................................ 21, 91
master roll ....................................................... 20, 29, 87
N
number of prints ................................................... 33, 79
O
On-Line Print Function ............................................... 82
E
Enlargement and Reduction ........................................ 39
Enlargements .............................................................. 39
Error Messages ........................................................... 99
F
fan unit ........................................................................ 29
feeder roller ................................................................ 29
feed tray ...................................................................... 19
Feed tray descend switch .................................... 19, 103
Feed pressure adjuster lever ................................. 19, 35
front cover ....................................................... 19, 84, 92
H
How Platemaking and Printing is Performed ............. 29
I
If Paper Runs Out During Printing ........................... 103
ink pack ................................................................ 20, 84
Installing the Drum Unit ............................................. 94
122
P
Paper Adhering to Drum ........................................... 109
Paper ejection belt ...................................................... 29
Paper Jams ................................................................ 107
Paper separator unit .................................................... 29
Paper Size ............................................................. 28, 44
Paper Stopper ........................................................ 21, 50
Paper stripper finger ................................................... 29
Part Names and Their Functions ................................ 19
personal computer ................................................ 18, 82
PLATE MAKING key ................................................ 22
Platemaking ................................................................ 29
Platemaking/Printing is Not Possible ......................... 98
Positioning the Document .......................................... 36
Positioning the Machine ............................................. 12
Power Does Not Turn ON .......................................... 98
power swich .................................................... 19, 25, 26
press roller .................................................................. 29
Print count .................................................................. 33
PRINT key .................................................................. 23
Print Output ................................................................ 49
Index
Print Speed Adjustment Function ............................... 80
print tray ............................................................... 21, 49
Printer Appearance ..................................................... 19
Printing ....................................................................... 29
Printing and Duplicating Cautions ............................. 14
Printing Position Adjustment Function ...................... 81
PRINTING POSITION ADJUSTMENT keys ..... 23, 81
Printing position indicator lamp ........................... 23, 81
PRINTING SPEED ADJUSTMENT keys ........... 23, 80
Printing speed indicator lamp ............................... 23, 80
Q
V
Vertical Placement ...................................................... 36
W
Warning Sticker .......................................................... 11
When “MASTER SET MISS” is Displayed ................... 114
When “MAST. EJECT ERROR” is Displayed ......... 111
When “PAPER LEFT JAM” is displayed
(Feed Tray) ............................................................... 107
When “PAPER RIGHT JAM” is displayed
(Print Tray) ............................................................... 108
1
2
Quick Operation Guide ............................................. 124
Z
R
Reductions .................................................................. 39
Removing the Drum Unit ........................................... 92
Replacing the Drum Unit ............................................ 92
Replacing the Ink Pack ............................................... 84
Replacing the Master Ejection Core ........................... 90
Replacing the Master Roll .......................................... 87
zoom ratio ............................................................. 32, 39
Other
= key ........................................................... 23, 69, 71
1%-Step Enlargement and Reduction ......................... 42
2-in-1 Layout .............................................................. 61
2-up Function .............................................................. 58
94% Reduction ........................................................... 40
X
S
Saving Settings ........................................................... 54
Sectional Printing ....................................................... 67
Sectional Printing(changing print quantity per document) .. 71
Selecting Printing Paper Size ..................................... 44
set .......................................................................... 24, 69
Side guides ............................................................ 19, 34
speed lamp .................................................................. 80
Standard Mode ............................................................ 26
STOP key .............................................................. 23, 79
Support tray .......................................................... 19, 34
Supplying or Changing Paper While Printing .......... 103
System Setup .............................................................. 18
T
Appendix
TEST PRINT key ................................................. 22, 78
Text/Photograph/Text and Photograph Mode ............. 47
Thermal head .............................................................. 29
Total Counter Display Function ................................. 79
total number of plates ................................................. 79
Truing up Printed Pages .............................................. 51
Turning OFF Printer Power ........................................ 26
Turning ON Printer Power .......................................... 25
Turning Power ON/OFF ............................................. 25
U
“U” groove of holder .................................................. 85
123
Quick Operation Guide
●Platemaking.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Install the print tray.
Open the supplemental paper tray.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Hold the lever and adjust the side
guides to the paper size.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Place a stack of aligned sheets in the
feeder tray.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
124
Quick Operation Guide
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Raise the paper stacker guides and
paper stopper, and adjust them to
the size of the printing paper.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Make the required settings on the
control panel.
Enlargement and Reduction, Plate Darkness,
Document mode, 94% Reduction, 2 IN 1
Function
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PLATE MAKING) key.
2
T
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Turning the power ON.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Check the finished plate. Adjust the
printing position, printing speed and
other settings as required.
Tip
• To make another test print, press
(TEST PRINT) key.
T
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
●Platemaking.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Set the document in place.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
●Print
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Enter the number of prints on the
key pad.
Tip
• To change the number of prints,
press C (CLEAR) key, and enter
the desired number of prints.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Press
(PRINT) key.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Select the paper size.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
125
Appendix
Tip
• To stop the machine midway during
operation, press
(STOP) key.
M7-Y1250 2001.07