HW-K650
HW-K651
User manual
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register your product at
www.samsung.com/register
GETTING STARTED
GETTING STARTED
Safety Information
●● The following also applies to the Wireless Subwoofer (PS-WK650/PS-WK651).
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lighting flash and arrowhead within the triangle
indicates that there is dangerous voltage Inside the
product.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
The explanation point within the triangle indicates
that there are important instructions accompanying
the product.
Class II product : This symbol indicates that a safety connection to electrical earth (ground) is not required.
AC voltage : Rated voltage marked with this symbol is AC voltage
DC voltage : Rated voltage marked with this symbol is DC voltage.
Caution. Consult instructions for use : This symbol instructs the user to consult the user manual for further
safety related information.
WARNING
• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
• This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive
harm.
CAUTION
• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases on the apparatus.
• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug
must be easily and readily accessible at all times.
CALIFORNIA USA ONLY
This perchlorate warning applies only to primary CR ( Manganese Dioxide )
Lithium coin cells in the product sold or distributed ONLY in California USA
" Perchlorate Material - special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate. "
2
GETTING STARTED
FCC NOTE (for U.S.A):
Class B FCC Statement
• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and
receiver.
• Connecting the equipment to an outlet on a circuit different
from that to which the receiver is connected.
• Consulting the dealer or an experienced radio/TV
technician for help.
FCC Radiation Exposure Statement :
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment.
This equipment should be installed and operated so there is
at least 8 inches (20 cm) between the radiator and your body.
This device and its antenna(s) must not be co-located or
operated in conjunction with any other antenna or transmitter.
Licenses
FCC Caution :
• Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate this equipment. This device complies
with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio and the double-D symbol are
trademarks of Dolby Laboratories.
• This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic interference
with electric appliances, such as radios and televisions,
use shielded cables and connectors for connections.
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing Limited.
DTS, the Symbol, & DTS and the Symbol together are
registered trademarks, and DTS 2.0 Channel is a
trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
Important Safety Instructions
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below. Keep these
operating instructions handy for future reference.
1)Read these instructions.
2)Keep these Instructions.
3)Heed all warnings.
4)Follow all instructions.
5)Do not use this apparatus near water.
6)Clean only with a dry cloth.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing LLC in the
United States and other countries.
3
ENG
The included module(s) has been tested and found to
comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following
measures:
7)Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions.
8)Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9)Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10)Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11)Only use attachments/accessories specified by the
manufacturer.
12)Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or when
unused for long periods of time.
14)Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any
way, such as when the power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
GETTING STARTED
Precautions
2.7 inch
3.9 inch
3.9 inch
3.9 inch
Ensure that the AC power supply in your house complies with the power requirements listed on the identification sticker
located on the bottom of your product. Install your product horizontally, on a suitable base (furniture), with enough space
around it for ventilation (3~4 inches). Make sure the ventilation slots are not covered. Do not place the unit on amplifiers
or other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, disconnect
the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.
During thunderstorms, disconnect the AC plug from the
wall outlet. Voltage peaks due to lightning could damage
the unit.
Do not expose the unit to direct sunlight or other heat
sources. This could lead to overheating and cause the
unit to malfunction.
Protect the product from moisture (i.e. vases), and
excess heat (e.g. a fireplace) or equipment creating
strong magnetic or electric fields. Unplug the power
cable from the AC wall socket if the unit malfunctions.
Your product is not intended for industrial use. It is for
personal use only. Condensation may occur if your
product has been stored in cold temperatures. If
transporting the unit during the winter, wait approximately
2 hours until the unit has reached room temperature
before using.
The battery used with this product contains chemicals
that are harmful to the environment. Do not dispose of
the battery in the general household trash. Do not
expose the battery to excess heat, direct sunlight, or fire.
Do not short circuit, disassemble, or overheat the battery.
Danger of explosion if the battery is replaced incorrectly.
Replace only with the same or equivalent type.
WARNING: DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD. The remote control supplied with
this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from
children. If the battery compartment does not close securely, stop using the remote and make sure to
keep it away from children. If you think the battery might have been swallowed or placed inside any part of the body,
seek immediate medical attention.
4
GETTING STARTED
CONTENTS
24FUNCTIONS
6
25Bluetooth
2
Safety Information
24Input Mode
What’s Included
28
Using the Multiroom App
8Rear / Bottom Panel
31
Software Update
12INSTALLATION
33Troubleshooting
7DESCRIPTIONS
30
7Front / Right Side Panel
9Remote Control
33TROUBLESHOOTING
12Installing the Soundbar
12
16
34APPENDIX
Installing the Wall Mount
34Specifications
Detaching the Soundbar from the Wall
17CONNECTIONS
17
Connecting the Subwoofer
19
Connecting to a TV Using a Digital Optical
Cable
19
20
20
Figures and illustrations in this User Manual are
provided for reference only and may differ from actual
product appearance.
Connecting to a TV
Connecting to a TV Using an HDMI (Digital)
Cable
TV SoundConnect
22
Connecting to External Devices
23
HDMI Cable
Using the Network Standby On
Function
22Optical or Analog Audio Cable
5
ENG
2GETTING STARTED
GETTING STARTED
What’s Included
Before reading the User’s Manual
Note the following terms before reading the user manual.
++Icons used in this manual
Icon
Term
Caution
Note
Definition
Indicates a situation where a function does not operate or settings may be canceled.
Indicates tips or instructions on the page that help you operate a function.
Check for the supplied accessories shown below.
Remote Control /
Lithium Battery
(3V : CR2032)
(AH59-02733B /
4301-001042)
A
B
Power Cord : 2 EA
(3903-000599)
CENTER LINE
A-TYPE : 616mm
B-TYPE : 360mm
B
Optical Cable
(AH39-00779A)
Holder-Screw : 2 EA
(AH61-04110A)
Screw : 2 EA
(6003-001334)
A
Wall Mount Guide
(AH63-04369A)
Bracket-Wall Mount L
(AH61-04106A)
AC/DC Adapter
(BN44-00862A)
Bracket-Wall Mount R
(AH61-04114A)
●● The appearance of the accessories may differ slightly from the illustrations above.
●● Micro USB to USB adapter and HDMI cables are sold separately. To purchase, contact a Samsung Service
Center or Samsung Customer Care.
6
DESCRIPTIONS
DESCRIPTIONS
Front / Right Side Panel
/
(Volume) Button
ENG
1
Controls the volume level.
The numeric value of the volume level appears in the front
panel display.
2
(Source) Button
Right Side
Selects the D.IN, AUX, HDMI, BT, or TV input.
button
●● While the unit is powered on, pressing the
for more than 3 seconds sets the button to act as the
(Mute) button. To cancel the
(Mute) button
button for more than 3 seconds
setup, press the
again.
3
2
1
3
(Power) Button
Turns the power on and off.
Display
Remote Control Sensor
Displays the current mode.
●● When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.
●● When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.
●● If you want to enjoy sound only from the Soundbar, you must turn off the TV's speakers in the Audio Setup
menu of your TV. Refer to the owner's manual supplied with your TV.
7
DESCRIPTIONS
Rear / Bottom Panel
DIGITAL AUDIO IN (OPTICAL)
Connect to the digital (optical) output of
an external device.
SERVICE
DC 24V
(Power Supply In)
DIGITAL AUDIO IN
(OPTICAL)
To upgrade the product's software
through the USB Port.
Connect the AC/DC power
adaptor to the power supply
jack, and then connect the
AC/DC power adaptor plug to
a wall outlet.
SERVICE
AUX IN
AUX IN
Connect to the Analog output of an
external device.
DC 24V
HDMI IN
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
Wi-Fi SETUP
SPK ADD
DC 24V
HDMI OUT
(TV-ARC)
AUX IN
LABEL
Wi-Fi SETUP
Press this button to
connect your Soundbar to
your network using Wi-Fi
setup. (Requires a smart
device and the Samsung
Multiroom app.
See page 28.)
HDMI IN
Wi-Fi SETUP
SPK ADD
HDMI IN
SPK ADD
Press the button to connect
the Soundbar to a Samsung
HUB (purchased separately)
or a network. (Requires a
smart device and the
Samsung Multiroom app.
See page 28.)
HDMI OUT
(TV-ARC)
Inputs digital video and
audio signals
simultaneously using an
HDMI cable. Use when
connecting a supported
external device.
HDMI OUT (TV-ARC)
Outputs digital video and audio signals
simultaneously using an HDMI cable.
●● When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.
Do not pull the cable.
●● Do not connect this unit or other components to an AC outlet until all connections between components
are complete.
●● Make sure to rest the AC/DC Adapter flat on a table or the floor. If you place the AC/DC Adapter so that it
is hanging with the AC cord input facing upwards, water or other foreign substances could enter the
Adapter and cause the Adapter to malfunction.
8
Remote Control
DESCRIPTIONS
Mute
You can turn the volume down to 0 with the push of a button.
Press again to restore the sound to the previous volume level.
Repeat
The Repeat function is available only when playing back music using Songs on
Phone or DMS in the Samsung Multiroom app.
OFF - REPEAT : Cancels Repeat Playback.
TRACK - REPEAT : Plays a track repeatedly.
ALL - REPEAT : Plays all tracks repeatedly.
Skip Forward
If there is more than one file on the device you are playing, and you press
the ] button, the next file is selected.
Bluetooth POWER
Press the Bluetooth POWER button on the remote to turn the Bluetooth
POWER On function on and off. See pages 21 and 26 for details.
SOUND
Surround Sound adds depth and spaciousness to the sound. Pressing the
SOUND button repeatedly cycles through the Surround Sound settings :
ON - SURROUND SOUND, OFF - SURROUND SOUND
Press and hold the  button for about 5 seconds to turn the Anynet+ function
on or off.
OFF - ANYNET+, ON - ANYNET+
The Anynet+ function lets you control the Soundbar with the remote from an
Anynet+ compatible Samsung TV.
The Soundbar must be connected to the TV via an HDMI cable.
Press and hold the  button for about 5 seconds to turn the Auto Power Link
function on or off.
OFF - POWER LINK, ON - POWER LINK
* Auto Power Link
Synchronizes the Soundbar to a connected Optical source via the Optical jack
so it turns on automatically when you turn on your TV. (See page 19)
The Auto Power Link function is only available in the D.IN mode.
SOUND EFFECT
You can select from 6 sound modes - STANDARD (Original Sound), MUSIC,
CLEAR VOICE, SPORTS, MOVIE, and NIGHT - depending on the content
you want to listen to.
Select the STANDARD mode if you want to enjoy the original sound.
* DRC (Dynamic Range Control)
Lets you apply dynamic range control to Dolby Digital.
Press and hold the SOUND EFFECT button for about 5 seconds in
STANDBY mode to turn the DRC (Dynamic Range Control) function on or off.
9
ENG
SOURCE
Press to select a source connected to the Soundbar.
DESCRIPTIONS
Power
Turns the Soundbar on and off.
Volume
Adjusts the volume level of the unit.
Play / Pause
Press the p button to pause a file temporarily.
Press the p button again to play the selected file.
Skip Back
If there is more than one file on the device you are playing, and you press
the [ button, the previous file is selected.
SOUND CONTROL
Press to select TREBLE, BASS, SUBWOOFER LEVEL or AUDIO SYNC.
Then, use the ,  buttons to adjust the TREBLE or BASS volume from
-3 ~ +3, SUBWOOFER LEVEL volume from -12, -6 ~ +6.
Press and hold the SOUND CONTROL button for about 5 seconds to adjust
the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2KHz, 2.5KHz,
5KHz, and 10KHz are selectable and each can be adjusted to a setting between
-6 ~ +6.
If the Soundbar is connected to a digital TV and the video appears out of sync
with the audio, press the SOUND CONTROL button to sync the audio with the
video. Use the ,  buttons to set the audio delay between
0 ms ~ 300 ms. In TV mode and BT mode, the Audio Sync function may not
available.
●● Operate the TV using the TV's remote control.
++Controlling the Soundbar using Your TV Remote Control
1. Press and hold the
SOUND button for more than 5 seconds while the Soundbar is turned on.
2. “ON - TV REMOTE” appears on the Soundbar’s display.
3. In the TV’s menu, set the TV speaker to external speaker.
●●
●●
●●
●●
This function is not available when the Soundbar is in TV ARC mode or in HDMI mode.
buttons are available to control the Soundbar.
Only the VOL +/- and
TV menus differ by manufacturer and model. Refer to the TV's user manual for further information.
Manufacturers supporting this function:
- VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, GRUNDIG, Hisense, RCA
- This function may not be compatible with your TV's remote depending on the remote control's manufacturer.
●● To turn off this function, press the
SOUND button for 5 seconds.
"OFF - TV REMOTE" appears on the Soundbar's display.
10
DESCRIPTIONS
Installing the Battery in the Remote Control
ENG
1. Use a suitable coin to turn the
remote control's battery cover
counterclockwise to remove it
as shown in the figure above.
2. Insert a 3V lithium battery. Keep the
positive (+) pole facing up when inserting
the battery. Put the battery cover on and
align the '●' marks side by side as
shown in the figure above.
11
3. Use a suitable coin to
turn the remote control
battery cover clockwise
as far as it will go to fix it
in place.
INSTALLATION
INSTALLATION
Installing the Soundbar
Installing the Wall Mount
++Installation Precautions
●● Install on a vertical wall only.
●● For the installation, avoid a location with high temperature or humidity, or a wall that cannot sustain the weight of
the set.
●● Check the strength of the wall. If the wall is not strong enough to support the unit, reinforce the wall or install the
unit on a different wall that can support the unit's weight.
●● Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster board, iron board,
wood, etc.). If possible, fix the support screws into wall studs.
●● Purchase wall mounting screws according to the type and thickness of the wall you will mount the Soundbar on.
-- Diameter: M5
-- Length: 1 3/8 inches or longer recommended.
●● Connect cables from the unit to external devices before you install it on the wall.
●● Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an electric shock.
2 inches or more
1. Place the Wall Mount Guide against the wall surface.
• The Wall Mount Guide must be level.
• If your TV is mounted on the wall, install the Soundbar at least 2 inches (5 cm) below the TV.
12
INSTALLATION
ENG
A
B
CENTER LINE
B
A-TYPE : 616mm
B-TYPE : 360mm
A
Center Line
2. Align the Paper Template’s Center Line with the center of your TV (if you are mounting the Soundbar below your
TV), and then fix the Wall Mount Guide to the wall using tape.
●● If you are not mounting below a TV, place the Center Line in the center of the installation area.
A
B
CENTER LINE
A-TYPE : 616mm
B-TYPE : 360mm
B
A
A
B
3. Push a pen tip or sharpened pencil tip through the center of the A-TYPE images on each end of the Guide to
mark the holes for the supporting screws, and then remove the Wall Mount Guide.
4. Using an appropriately sized drill bit, drill a hole in the wall at each marking.
●● If the markings do not correspond to the positions of studs, make sure you insert appropriate anchors or
mollies into the holes before you insert the support screws. If you use anchors or mollies, make sure the
holes you drill are large enough for the anchors or mollies you use.
13
INSTALLATION
5. Push a screw (not supplied) through each Holder-Screw, and then screw each screw firmly into a support screw
hole.
6. Use the two Screws (M4 x L12) to attach both Bracket-Wall Mount L and R to the Soundbar’s bottom. For a
proper fit, make sure to align the bumps on the Soundbar to the holes on the brackets.
Rear of Soundbar
Right end of Soundbar
●● When assembling, make sure the hanger parts of the Bracket-Wall Mounts are located behind the rear
of the Soundbar. See the illustration above.
Wall Mount R
Wall Mount L
●● The left and right mounts are different shapes. Make sure to position them correctly.
14
INSTALLATION
ENG
7. Install the Soundbar with the attached Bracket-Wall Mounts by hanging the Bracket-Wall Mounts on the
Holder-Screws on the wall.
●● Slightly tilt the Soundbar to insert both Holder-Screw heads into Bracket-Wall Mount holes. Push the
Soundbar in the direction of the arrow to make sure both sides are firmly fixed.
15
INSTALLATION
Detaching the Soundbar from the Wall
1. To separate the Soundbar from the wall mount, push it in the direction of arrow, tilt it up slightly, and then pull it
away from the wall as shown.
●● Do not hang onto the installed unit and avoid striking or dropping the unit.
●● Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may cause an injury or
damage the product.
●● When the unit is installed on a wall, please make sure that children do not pull any of the connecting
cables, as this may cause it to fall.
●● For the optimal performance of a wall mount installation, install the speaker system at least 2 inches
(5 cm) below the TV, if the TV is mounted on the wall.
●● For your safety, if you do not mount the unit on the wall, install it on a secure, flat surface where it is unlikely
to fall.
16
CONNECTIONS
CONNECTIONS
Connecting the Subwoofer
Connecting to the Subwoofer Automatically
The Subwoofer's linking ID is preset at the factory and the main unit and subwoofer should link (connect wirelessly)
automatically when the main unit and subwoofer are turned on.
• When the subwoofer is completely connected, the blue LED Link Indicator on the subwoofer stops blinking and
glows continuously.
Connecting to the Subwoofer Manually
If the blue LED light does not stop blinking when the main unit and subwoofer are turned on, please set the ID by
following the steps below.
●● Important: Before you begin, put the battery into the remote. See page 11 for instructions.
POWER
1. Plug the power cords of the main unit and subwoofer into an AC wall outlet.
2. Press the ID SET button on the back of the subwoofer with a small, pointed object for 5 seconds.
• The STANDBY indicator turns off and the LINK indicator (Blue LED) blinks quickly.
3. While the main unit is powered off (in STANDBY mode), press and hold the
5 seconds.
(Mute) on the remote control for
4. The ID SET message appears on the Soundbar's display.
5. To finalize the link, turn the main unit’s power on while the subwoofer’s Blue LED blinks.
• The main unit and the subwoofer should now be linked (connected).
• The LINK indicator (Blue LED) on the subwoofer should be glowing continuously and not blinking.
• If the LINK indicator is not solid blue, the linking process has failed. Turn off the main unit and start again from
Step 2.
• You can enjoy better sound from the wireless subwoofer by selecting a Sound Effect. (See page 9)
17
ENG
●● Do not connect the power cord of this product or your TV to a wall outlet until all connections between
components are complete.
●● Before moving or installing this product, be sure to turn off the power and disconnect the power cord.
CONNECTIONS
●● Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
●● If the main unit is powered off,the wireless subwoofer will in standy mode and the STNDBY LED on the
front will blink Red directly. (no blue LED).
●● If you use a device that uses the same frequency (2.4GHz) as the Soundbar near the Soundbar,
interference may cause some sound interruption.
●● The maximum transmission distance of the wireless signal between the main unit and subwoofer is about
32.8 ft, but may vary depending on your operating environment. If a steel-concrete or metallic wall is
between the main unit and the wireless subwoofer, the system may not operate at all, because the wireless
signal cannot penetrate metal.
●● If the main unit doesn't make a wireless connection, follow steps 1-5 on the previous page to re-set the
connection between the main unit and wireless subwoofer.
●● The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and
moisture.
●● For optimal listening performance, make sure that the area around the wireless subwoofer location is clear
of any obstructions.
LED indicator lamp status on subwoofer
LED
Red
Status
On
On
Blue
Red and blue
Blinking
Blinking
Description
Resolution
Standby (with the Soundbar main
unit turned off)
Check the power supply to the
Soundbar main unit
Connection failed
Connect again
(refer to the instructions on manual
connection in the user manual)
Successfully connected
(normal operation)
-
Standby (with the Soundbar main
unit turned off)
Check the power supply to the
Soundbar main unit
Connection failed
Connect again
(refer to the instructions on manual
connection in the user manual)
Malfunction
Contact the service center.
18
CONNECTIONS
Connecting to a TV
Connecting to a TV Using a Digital Optical Cable
Optical Cable
DIGITAL AUDIO IN
(OPTICAL)
OPTICAL OUT
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN
DIGITAL AUDIO IN
(OPTICAL)
USB (5V 0.5A)
Wi-Fi SETUP
SPK ADD
DC 24V
HDMI OUT
(TV-ARC)
AUX IN
1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV with a
digital optical cable.
button on the right side of the Soundbar or the SOURCE button on the remote control to select
2. Press the
the D.IN mode.
++Auto Power Link
If you have connected the main unit to a TV with a digital optical cable, you can set the Auto Power function ON
to have the Soundbar turn on automatically when you turn the TV on.
1. Connect the Soundbar and a TV with a digital optical cable.
2. Press the
D.IN mode.
button on the main unit’s right side or the SOURCE button on the remote control to select the
3. Press the  button on the remote control for 5 seconds to turn Auto Power Link on or off.
●● Auto Power Link is set to ON by default.
●● Depending on the connected device, Auto Power Link may not function.
●● This function is only available in the D.IN mode.
19
ENG
●● Important: Before you begin, put the battery into the remote. See page 11 for instructions.
CONNECTIONS
Connecting to a TV Using an HDMI (Digital) Cable
HDMI Cable
(not supplied)
HDMI IN
HDMI IN
HDMI OUT
(TV-ARC)
DIGITAL AUDIO IN
(OPTICAL)
HDMI OUT
(TV-ARC)
HDMI IN
DIGITAL AUDIO IN
(OPTICAL)
USB (5V 0.5A)
Wi-Fi SETUP
SPK ADD
DC 24V
HDMI OUT
(TV-ARC)
AUX IN
1. Connect an HDMI cable (not supplied) from the HDMI OUT (TV-ARC) jack on the bottom of the product to the
HDMI IN jack on your TV.
button on the right side of the Soundbar or the SOURCE button on the remote control to select
2. Press the
the D.IN mode.
●● HDMI is an interface that enables the digital transmission of video and audio data with just a single
connector.
●● If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.
●● We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one whose
diameter is less than 0.55 inches.
●● Anynet+ must be turned on.
●● This function is not available if the HDMI cable does not support ARC.
TV SoundConnect
You can enjoy TV sound through your Soundbar when it is connected to a Samsung TV that supports the
TV SoundConnect function.
Connect
1. Turn on the TV and Soundbar.
2. Press the
mode.
button on the main unit’s right side or the SOURCE button on the remote control to select the TV
3. On the TV, a message asking whether to enable the TV SoundConnect function appears.
4. Select <Yes> using the TV's remote control to finish connecting the TV and Soundbar.
20
CONNECTIONS
●● The TV SoundConnect (SoundShare) function is supported by some Samsung TVs released from 2012 on.
Check whether your TV supports the TV SoundConnect (SoundShare) function before you begin. (For
further information, refer to the TV’s user manual.).
●● If your Samsung TV was released before 2014, check the SoundShare setting menu.
●● If the distance between the TV and Soundbar exceeds 32.8 ft, the connection may not be stable or the
audio may stutter. If this occurs, relocate the TV or Soundbar so that they are within operational range, and
then re-establish the TV SoundConnect connection.
●● TV SoundConnect Operational Ranges:
-- Recommended pairing range: within 78.7 inches (within 2m).
-- Recommended operational range: within 32.8 ft. (10m).
●● The Play/Pause, Next, and Prev buttons on the Soundbar or Soundbar's remote do not control the TV.
++Using the Bluetooth POWER On function
The Bluetooth POWER On function is available after you have successfully connected the Soundbar to a Bluetooth
compatible TV using TV SoundConnect. When the Bluetooth POWER On function is ON, turning the connected TV on
or off will turn the Soundbar's power on and off as well.
1. Connect the TV to your Soundbar using the TV SoundConnect function.
2. Press the Bluetooth POWER button on the Soundbar remote. ON - BLUETOOTH POWER appears on
the Soundbar’s display.
• ON - BLUETOOTH POWER : The Soundbar turns on and off when you turn the TV on or off.
• OFF - BLUETOOTH POWER : The Soundbar only turns off when you turn the TV off.
●● This function is supported by some Samsung TVs released from 2013 on.
21
ENG
●● If the TV SoundConnect linking process fails, navigate to SoundConnect in the TV's Sound menu, select
Add New Device, and set Add New Device to ON. Then, try again.
●● Switching the Soundbar’s mode from TV to another mode automatically terminates TV SoundConnect.
●● To connect the Soundbar to another TV, the existing connection must be terminated.
●● To terminate the existing connection, press and hold the p button on the remote for 5 seconds or switch
to another mode. To connect to the other TV, follow Steps 1 through 4 on the previous page.
CONNECTIONS
Connecting to External Devices
Optical or Analog Audio Cable
This unit comes equipped with one digital optical in jack and one analog audio (AUX) in jack, giving you two
ways to connect it to external devices.
Audio Cable
(not supplied)
AUX OUT
BD / DVD player /
Set-top box /
Game console
AUX IN
Optical Cable
DIGITAL AUDIO IN
(OPTICAL)
OPTICAL OUT
DIGITAL AUDIO IN
(OPTICAL)
DIGITAL AUDIO IN
(OPTICAL)
USB (5V 0.5A)
HDMI IN
DIGITAL AUDIO IN
(OPTICAL)
USB (5V 0.5A)
AUX IN
Wi-Fi SETUP
SPK ADD
HDMI OUT
(TV-ARC)
DC 24V
USB (5V 0.5A)
AUX IN
AUX IN
++AUX Cable
1. Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an audio cable.
button on the right side of the Soundbar or the SOURCE button on the remote control to select
2. Press the
the AUX mode.
++Optical Cable
1. Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source Device using a
digital optical cable.
button on the right side of the Soundbar or the SOURCE button on the remote control to select
2. Press the
the D.IN mode.
22
CONNECTIONS
HDMI Cable
Digital Devices
HDMI OUT
HDMI Cable
(not supplied)
HDMI IN
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN
HDMI IN
DIGITAL AUDIO IN
(OPTICAL)
USB (5V 0.5A)
Wi-Fi SETUP
SPK ADD
DC 24V
HDMI OUT
(TV-ARC)
AUX IN
1. Connect an HDMI cable (not supplied) from the HDMI IN jack on the bottom of the product to the HDMI OUT jack
on your digital device.
button on the right side of the Soundbar or the SOURCE button on the remote control to select
2. Press the
the HDMI mode.
23
ENG
HDMI is the standard digital interface for connecting to TVs, projectors, DVD players, Blu-ray players, set top boxes,
and more.
HDMI prevents any degradation to the signal due to conversion to analog and maintains the video and audio
quality of the original digital source.
FUNCTIONS
FUNCTIONS
Input Mode
button on the main unit’s right side or the SOURCE button on the remote control to select the mode
Press the
you want.
Right Side of the Soundbar
Input mode
Display
Optical Digital input
D.IN
ARC (HDMI OUT) input
AUX input
HDMI input
AUX
HDMI
BLUETOOTH mode
TV SoundConnect
BT
TV
Auto Power Down Function
The unit turns off automatically in the following situations.
●● D.IN / HDMI / BT / TV Mode
-- If there is no audio signal for 5 minutes.
●● AUX Mode
-- If the AUX cable is disconnected for 5 minutes.
-- If there is no KEY input for 8 hours when the AUX cable is connected. (Auto Power Down function can be
turned off only in that case.)
To turn off Auto Power Down function, while in AUX mode, press and hold the p button for 5 seconds.
ON - AUTO POWER DOWN / OFF - AUTO POWER DOWN appears on the display.
24
FUNCTIONS
Bluetooth
To connect the Soundbar to a Bluetooth device
Check if the Bluetooth device supports the Bluetooth compliant stereo headset function.
Connect
1. Press the
mode.
Bluetooth device
button on the main unit’s right side or the SOURCE button on the remote control to select the BT
• You will see BT READY on the front display of the Soundbar.
2. Select the Bluetooth menu on the Bluetooth device you want to connect. (Refer to the Bluetooth device's user
manual.)
3. Select "[AV] Samsung Soundbar Kxxx" from the list.
• When the Soundbar is connected to the Bluetooth device, it will display [Bluetooth device name]  BT on
the front display.
• The device name can only be displayed in English. An underline " _ " will be displayed if the name is not in
English.
• If the Bluetooth device has failed to pair with the Soundbar, delete the previous "[AV] Samsung Soundbar Kxxx"
found by the Bluetooth device and have it search for the Soundbar again.
4. Play music on the connected device.
• You can listen to the music playing on the connected Bluetooth device over the Soundbar.
• In BT mode, the Play / Pause / Next / Prev functions are not available. However, these functions are available
on Bluetooth devices supporting AVRCP.
25
ENG
You can connect a Bluetooth device to the Soundbar and enjoy music with stereo sound, all without wires!
FUNCTIONS
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
Only one Bluetooth device can be paired at a time.
The Bluetooth connection will be terminated when you turn the Soundbar off.
The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:
-- If there is a strong electrical field around the Soundbar.
-- If several Bluetooth devices are simultaneously paired with the Soundbar.
-- If the Bluetooth device is turned off, not in place, or malfunctions.
Note that such devices as microwave ovens, wireless LAN adaptors, fluorescent lights, and gas stoves use
the same frequency range as the Bluetooth device, which can cause electric interference.
The Soundbar supports SBC data (44.1kHz, 48kHz).
Connect only to a Bluetooth device that supports the A2DP (AV) function.
You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free) function.
Once you have paired the Soundbar to a Bluetooth device, selecting "[AV] Samsung Soundbar Kxxx"
from the device's scanned devices list will automatically change the Soundbar to BT mode.
-- Available only if the Soundbar is listed among the Bluetooth device’s paired devices. (The Bluetooth
device and the Soundbar must have been previously paired at least once.)
The Soundbar will appear in the Bluetooth device’s searched devices list only when the Soundbar is
displaying BT READY.
In the TV SoundConnect mode, the Soundbar cannot be paired to another Bluetooth device.
Bluetooth POWER On (Bluetooth POWER)
If a previously paired Bluetooth device tries to pair with the Soundbar when the Bluetooth POWER On function is on
and the Soundbar is turned off, the Soundbar turns on automatically.
1. Press the Bluetooth POWER button on the remote while the Soundbar is turned on.
2. ON - BLUETOOTH POWER appears on the Soundbar’s display.
To disconnect the Bluetooth device from A
Soundbar
You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device's user manual.
●● The Soundbar will be disconnected.
●● When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
BT DISCONNECTED on the front display.
26
FUNCTIONS
Press the SOURCE button on the remote control or the
another mode or turn off the Soundbar.
button on the product's right side to switch from BT to
●● The connected Bluetooth device will wait a certain amount of time for a response from the Soundbar before
terminating the connection. (Disconnection time may differ, depending on the Bluetooth device)
●● In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar
and the Bluetooth device exceeds 32.8 ft.
●● The Soundbar automatically turns off after 5 minutes in the Ready state.
++More About Bluetooth
Bluetooth is a technology that enables Bluetooth-compliant devices to interconnect easily with each other using a
short wireless connection.
●● A Bluetooth device may cause noise or malfunction, depending on usage, if:
-- A part of your body is in contact with the receiving/transmitting system of the Bluetooth device or the
Soundbar.
-- It is subject to electrical variation from obstructions caused by a wall, corner, or office partition.
-- It is exposed to electrical interference from same frequency-band devices including medical equipment,
microwave ovens, and wireless LANs.
●● Pair the Soundbar with the Bluetooth device while they are close together.
●● The further the distance between the Soundbar and Bluetooth device, the worse the quality is.
If the distance exceeds the Bluetooth operational range, the connection is lost.
●● In poor reception areas, the Bluetooth connection may not work properly.
●● The Bluetooth connection only works when it is close to the unit. The connection will be automatically cut off if the
Bluetooth device is out of range. Even within range, the sound quality may be degraded by obstacles such as
walls or doors.
●● This wireless device may cause electric interference during its operation.
27
ENG
To disconnect the Soundbar from A Bluetooth
device
FUNCTIONS
Using the Multiroom App
The Samsung Multiroom app lets you connect the Soundbar to a smart device, your network, and the Internet. Once
the Soundbar is connected to a smart device that has the Multiroom App installed, you can also connect the
Soundbar and multiple Samsung Multiroom devices together wirelessly and play audio through them.
BEFORE YOU BEGIN
++Communication Basics
Internet
Wireless Router
Smart Device:
Android or iOS
(App Control)
Requirements:
1. A Wireless Router and a Smart Device.
2. The wireless router must be connected to the Internet.
3. The smart device must be connected to the router via a Wi-Fi connection.
INSTALLING THE SAMSUNG MULTIROOM APP
To use the Soundbar with the Samsung Multiroom App, you must download and then install the Samsung Multiroom
App on your smart device. You can download the app from Google Play or the App Store. With the Samsung
Multiroom App installed, you can play music on your Soundbar that is stored on your smart device, located on other
connected devices, provided by other content providers, or streamed from Internet radio stations.
++Android or iOS
Download the Samsung Multiroom app from Google Play or the App Store of your smart device.
* Market search : Samsung Multiroom
or
28
FUNCTIONS
++Launching the Samsung Multiroom App
To launch the Samsung Multiroom app, tap the Multiroom app icon on your smart device.
ENG
Connecting the Soundbar to Your Network
On your smart device, select the Samsung Multiroom app. Follow the directions on your smart device’s screen.
You can use the following music sources with the Samsung Multiroom app.
-- Music files stored in your mobile phone, various music sources, and Internet radio.
[AV] Samsung Soundbar Kxxx
Music in mobile phone
Internet radio
Music service
29
FUNCTIONS
Using the Network Standby On
Function
The Network Standby On function is available if a wireless connection has been properly established between a smart
device and the Soundbar. This function turns on the Soundbar automatically when a smart device attempts to connect
to the Soundbar via Bluetooth or Wi-Fi. If you turn the Soundbar on via a Bluetooth connection, its input mode is set to
BT automatically. To turn the Soundbar on via Wi-Fi, you must have the Samsung Multiroom App installed on your
smart device.
1. Connect the smart device to your Soundbar.
2. Turn on the Network Standby On function by pressing the ] button on the Soundbar's remote for more than
5 seconds. You can turn the function off by pressing the ] button again for more than 5 seconds.
●● Network Standby On is available only if the Soundbar is listed among the smart device’s paired devices.
(The Smart device and the Soundbar must have been previously paired at least once.)
●● Soundbar will appear in the smart device’s searched devices list only when the Soundbar is displaying
[BT READY] or [WiFi READY].
●● In the TV SoundConnect mode, the Soundbar cannot be paired to another smart device.
●● If the Network Standby On function did not work:
-- The Network Standby On is set to Off. Set it to ON.
●● The Wi-Fi connection to the Soundbar will be terminated if the Soundbar’s power cord is disconnected or
the power is cut off. If the power is cut off, turn on the Soundbar and reconnect it.
●● If the Network Standby is set to Off, the Soundbar cannot be turned on by Bluetooth connection.
30
FUNCTIONS
Software Update
SERVICE
Wi-Fi SETUP
SPK ADD
DC 24V
HDMI OUT
(TV-ARC)
AUX IN
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
Micro USB to
USB adapter Cable
(not supplied)
AUX IN
Updating with USB
Samsung may offer updates for the Soundbar's system firmware in the future.
If an update is offered, you can update the firmware by connecting a USB device with the firmware update stored on it
to the USB port on your Soundbar.
Note that if there are multiple update files, you must load them onto the USB device singly and use them to update the
firmware one file at a time.
Please visit samsung.com or contact the Samsung call center to receive more information about downloading update
files.
++Updating Procedure
1. Connect a Micro USB to USB adapter cable with a male USB 2.0 Micro USB plug (Type B) on one end
and a standard female 2.0 USB jack (Type A) on the other end to the micro USB jack on your Soundbar.
●● The Micro USB to USB adapter cable is sold separately. To purchase, contact a Samsung Service Center
or Samsung Customer Care.
2. Follow the steps below to download the product software:
Go to the Samsung website at (samsung.com/sec)  search for the model name - select the customer support
option (the option name is subject to change)
3. Save the downloaded software to a USB stick and select "Extract to the folder name" to unzip the folder.
4. Turn off the Soundbar and connect the USB stick containing the software update to the female port on a Micro
USB adapter cable.
5. Turn on the Soundbar. Within 3 minutes, UPDATE is displayed and updating begins.
6. After the update is complete, the Soundbar turns off and on again.
31
ENG
HDMI IN
DIGITAL AUDIO IN
(OPTICAL)
FUNCTIONS
++If UPDATE is not displayed
1. Turn off the Soundbar, disconnect and then reconnect the USB storage device that contains the update files to the
female end of the USB adapter cable.
2. Disconnect the Soundbar's power cord, reconnect it, and then turn on the Soundbar.
●● Insert a USB device containing the firmware update into the USB port on the main unit.
●● Updating firmware may not work properly if audio files supported by the Soundbar are stored in the USB
storage device.
●● Do not disconnect the power or remove the USB device while updates are being applied. The main unit will
turn off automatically after completing the firmware update.
●● After update is completed, the user setup in Soundbar is initialized. We recommend you write down your
settings so that you can easily reset them after the update. Note that updating firmware resets the
subwoofer connection too.
If the connection to the subwoofer is not re-established automatically after the update, refer to page 17.
If the software update fails, check that the USB stick is not defective.
●● Mac OS users should use MS-DOS (FAT) as the USB format.
●● Depending on the manufacturer, some USB devices may not be supported.
Auto update
If the Soundbar is connected to the Internet, it will automatically check for the latest firmware and update when new
firmware becomes available, even if it is turned off.
●● The Soundbar is configured to run Auto Update by default.
●● To use the Auto Update function, the Soundbar must be connected to the Internet.
●● The Wi-Fi connection to the Soundbar will be terminated if its power cord is disconnected or the power is
cut off. If the power is cut off, turn on the Soundbar and reconnect it.
32
TROUBLESHOOTING
TROUBLESHOOTING
Troubleshooting
The unit will not turn on.
• Is the power cord plugged into the outlet?
¼¼Connect the power plug to the outlet.
A function does not work when the button is pressed.
• Is there static electricity in the air?
¼¼Disconnect the power plug and connect it again.
Sound is not produced.
• Is the Mute function on?
¼¼Press the
function.
• Is the volume set to minimum?
(Mute) button to cancel the Mute
¼¼Adjust the volume.
The remote control does not work.
• Are the batteries drained?
• Is the distance between the remote control and main
unit too far?
¼¼Replace with new batteries.
¼¼Move closer to the unit.
The TV SoundConnect (TV pairing) failed.
• Does your TV support TV SoundConnect?
¼¼TV SoundConnect is supported by some Samsung
TVs released from 2012 on. Check your TV to see if it
supports TV SoundConnect.
• Is your TV firmware the latest version?
¼¼Update your TV with the latest firmware.
• Does an error occur when connecting?
¼¼Contact the Samsung Call Center.
¼¼Reset TV SoundConnect and connect again.
To reset the TV SoundConnect connection, press
and hold the p button for 5 seconds.
The red LED on the subwoofer blinks and the subwoofer is not producing sound.
¼¼Try to connect your subwoofer again.
(See Page 17)
• Your subwoofer may not be connected to the
main unit of the product.
Soundbar is not turned on by Bluetooth or Multiroom App.
¼¼If it's true, BT and Wifi functions are not allowed in
power off state. Press and hold the ] button for
5 seconds to turn on the Network Standby in power
on state.
• Check the Network Standby option is OFF.
33
ENG
Refer to the table below if this product does not function properly. If the problem you are experiencing is not listed
below or if the instructions below do not help, turn off the product, disconnect the power cord, and contact Samsung
Electronics at 1-800-SAMSUNG (1-800-726-7864).
APPENDIX
APPENDIX
Specifications
Weight
GENERAL
Dimensions
(W x H x D)
Main Unit
5.7 lbs (2.6 kg)
Subwoofer (PS-WK650, PS-WK651)
15.0 lbs (6.8 kg)
Main Unit
39.8 x 2.1 x 3.4 inches
(1010.5 x 54.0 x 87.5 mm)
Subwoofer (PS-WK650, PS-WK651)
17.8 x 13.2 x 6.1 inches
(452.0 x 335.0 x 154.0 mm)
Operating Temperature Range
+41°F to +95°F (+5°C to +35°C)
Operating Humidity Range
Rated
AMPLIFIER Output
Power
10 % to 75 %
Main Unit
30W x 6, 6 ohm, THD≦10%
Subwoofer (PS-WK650, PS-WK651)
160W, 3 ohm, THD≦10%
* Design, specifications and App screen are subject to change without prior notice.
* Nominal specifications
-- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
-- Weight and dimensions are approximate.
-- For more information about the power supply and power consumption, refer to the label attached to the
product.
-- Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our
website: www.samsung.com/recyclingdirect or call (877) 278 - 0799.
aa Open Source License Notice
-- For further information on Open Sources used in this product, please visit the website:
http://opensource.samsung.com
aa
License
-- The Spotify software is subject to third party licenses found here :
www.spotify.com/connect/third-party-licenses.
-- For more information about Spotify Connect, please visit www.spotify.com/connect
aa Important Note About Service
●● An administration fee may be charged if either:
a. An engineer is called out to your home at your request and there is no defect in the product.
b. You bring the unit to a repair center and there is no defect in the product.
●● You will be advised of the amount of the administration fee before any work is done or a home visit is made.
●● If you have a problem with this product, we strongly recommend you read the appropriate section of this
manual, review the Troubleshooting section on page 33, visit the Support page for your product at
www.samsung.com, or call Samsung Product Support (1-800-726-7864) to find an answer before you contact
a service center for a repair.
34
Warranty
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered
new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in
materials and workmanship for a limited warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States.
To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty
service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon
request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the
service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned
parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products
become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the
remaining original warranty, or ninety (90) days, whichever is longer.
SAMSUNG’s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are
set forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an
“AS IS” basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the
extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the
following, including, but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for
which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse,
neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies,
accessories, applications, installations, repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or
which damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer
adjustments and failure to follow operating instructions, cleaning, maintenance and environmental instructions that are covered
and prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to noise,
echo, interference or other signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free
operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO
OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS
PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS,
FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE
CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL
RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT
SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES
ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO OTHERS
AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT
CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER
THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
The benefits of this Limited Warranty extend only to the original purchaser of Samsung products from an authorized Samsung
reseller. THIS LIMITED WARRANTY SHALL NOT APPLY TO ANY SAMSUNG PRODUCTS PURCHASED FROM UNAUTHORIZED
RESELLERS OR RETAILERS, EXCEPT IN STATES WHERE SUCH RESTRICTION MAY BE PROHIBITED. For a list of Samsung
authorized retailers, please go to: http://www.samsung.com/us/peaceofmind/authorized_resellers.html
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG customer care center.
The party responsible for product compliance:
Samsung Electronics Co., LTD.
America QA lab of Samsung
19 Chapin Rd. Building D,
Pine Brook, New Jersey 07058
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
U.S.A
1-800-SAMSUNG
(726-7864)
www.samsung.com/us/support
©2016 Samsung Electronics Co.,Ltd. All rights reserved
WRITE
Samsung Electronics America, Inc.
85 Challenger Road
Ridgefield Park, NJ 07660