s
Data Sheet
Fire Safety & Security Products
MXL® Panel
Advanced Fire Protection System
ARCHITECT AND ENGINEER SPECIFICATIONS







FirePrintTM application-specific detection
More than 2,000 intelligent input-device capacity
Dynamic supervision of intelligent devices
Multiple command stations
Security-device monitoring
Sprinkler supervision
Detector-sensitivity readout / printout,
per NFPA 72 Chapter 7
 Intelligent / analog detection circuits:
─ Style 6 (Class A) or Style 4 (Class B)
 Conventional initiating circuits:
─ Style D (Class A) or Style B (Class B)
 Notification appliance circuits [NACs]:
─ Style Z (Class A) or Style Y (Class B)











Degrade-mode operation
Distributed processing
80-character backlit, alphanumeric display
32-character custom messages
Thermal-strip printer
Supervised remote printer
Compare system software
Fully field programmable, via laptop PC
Menu-driven operator commands
Central & distributed architecture
Up to 800-event history log with online
and offline reports
 User help screens
 Holiday schedule
 Logic-controlled output functions
 Multiple levels of password protection
 Automatic environmental compensation
for smoke detectors
 One-person ‘walk test’ via ‘loop,’ ‘zone’
or ‘system’
 Alarm verification by ‘device’ or ‘zone’
 Time-base controlled output functions
 City Tie / Lease Line
 Coded outputs
 Supervised serial annunciator
driver / input Interface
 16-gauge steel enclosure
 Multi-language display
 Intelligent interface to building /
process-management systems
 Operates as an interactive peer with
other MXL, MXL-IQs or MXLV systems
in a LifeLINK Network
 Pre-alarm operation
 NCC graphics
 NEC 760 power-limited circuits
( UL 864 9th Edition compliant)
 SinorixTM NFPA Approval (2001)
 UUKL Listed for Smoke Control
 UL 864 9th Edition Listed, ULC Listed;
CSFM, NYC Fire Department and
City of Chicago Approved
System Overview
The MXL fire panel is a microprocessor-based
advanced protection system. The use of the MXL
system’s unique multiprocessor ‘network’ design; as
well as its ability to utilize analog and conventional
detection devices, makes the MXL panel a highly
flexible and reliable fire-control system.
The MXL panel is ideally suited for commercial,
industrial and institutional fire-detection and
notification applications. The MXL system
complies with the requirements of NFPA Standard
72, and is listed by Underwriters Laboratories (UL),
via its UL 864 9th Edition. Underwriter’s’
Laboratories of Canada (ULC) also lists the MXL
panel for fire applications.
The MXL system is approved by CSFM, NYCFD and the City
of Chicago for use in those specific locales.
In addition to the standard fire applications, MXL is
UL Listed, under the category ‘UUKL for Smoke Control.’
The MXL panel can be used as a listed fireman’s smokecontrol station in high-rise office buildings, malls and
other multi-level or vast structures. The MXL
system also complies with Uniform Building Code
Section 905 requirements for smoke control.
The MXL panel is UL Listed for releasing SinorixTM
Engineered Fire Suppression System. MXL follows the
releasing requirements specified in the NFPA 2001.
MXL® Panel
s Industry, Inc.
Building Technologies Division
5000
MXL Components
The basic MXL control unit consists of the following
sub-assemblies: MMB-3 Main Control Board; MPS-6 /
MPS-12 Power Supply; MKB-2 Annunciator and
Keyboard; MME-3, or MLE-6 Enclosures. Optional
modules ─ which can be installed with the MXL
System ─ include: MOM-2/4 Expansion Card Cage;
ALD-2I Analog Loop Driver; CRM-4 Controllable Relay
Module; NIM-1W Network/Foreign Systems Interface
Module; REP-1 Network Repeater Module; CSM-4
Controllable Signal Module; CZM-4 Conventional Zone
Module; PIM-1 Peripheral Interface Driver; CMI-300
NCC-WAN Modem Interface Module; PSR-1 Remote
Power Supply; NET-4 Style 4 Network Interface, and
NET-7 Style 7 Network Interface.






[2] two-line, 80-character LCD display
indicator LEDs
display-control keys
numeric keypad
12 programmable function keys
all other keys necessary for operator control
These keys include but are not limited to: Acknowledge;
Silence and Reset. Model MKB-2 also includes spaces
for mounting the Model MMM-1 microphone module
and the Model TMM-1 telephone. Model MKB-2 is
supplied with two (2) blank plates for use when either
the microphone or telephone is omitted.
Display / Keyboard (MKB-5)
Additionally, the MXL system includes option modules
MOI-7 System Interface, MOD-16 Output Driven and
MID-16 Point Input Module. These option modules
can be used to drive graphic annunciators and
fireman’s smoke control stations, or to monitor
foreign systems.
The MXL is compatible with a full line of intelligent
initiating devices highlighted by the FirePrintTM
application-specific detectors: Models FP-11 and FPT11. The MXL panel is also compatible with FireFinder,
the NCC series of text and graphic command centers.
MXL Enhanced Main Board (MMB-3)
MKB-5
The MKB-5 display keyboard, which mounts on the inner
door of any MXL enclosure, provides:






6-1/4” VGA backlit, 80- character LCD display
indicator LEDs
12 programmable function keys
numeric keypad
user-programmable function keys
all other keys necessary for operator control
These keys include but are not limited to: Acknowledge;
Silence and Reset. Multiple Model MKB-5 modules can be
used; each providing full control of the MXL system. Up to
four (4) Model MKB-5 can operate in a fully supervised
mode; each with independent, built-in printer / driver
capability.
MMB-3
The function control of the MXL is contained on
the MMB-3 Main Control Board. Model MMB-3
offers a fast, integral microprocessor and
installation conveniences such as diagnostic LEDs
and removable terminal blocks for field wiring.
Model MMB-3 acts as the central controller for the
system, and includes two (2) ALD circuits and two
(2) notification appliance circuits. Model MMB-3
mounts in the MXL enclosure back box.
Display / Keyboard (MKB-2)
MKB-2
The Model MKB-2 display keyboard, which mounts
on the inner door of any MXL enclosure, provides:
s Industry, Inc.
Building Technologies Division
Power Supply (MPS-6)
MPS-6
Model MPS-6 is a fully supervised power supply that
provides the MXL system with primary DC power. Model
MPS-6 is rated at 6.5 Amps, and is unfiltered and
unregulated. Model MPS-6 supplies power to the MXL
Control Unit, and supplies its expansion modules with
power required for normal operation. Model MPS-6
incorporates a circuit breaker on the primary input, and
includes a built-in AC-line filter for surge and noise
suppression. Model MPS-6 mounts in the MXL enclosure
back box.
MXL Components ─ (continued)
Analog Loop Driver (ALD-2I)
Power Supply (MPS-12)
ALD-2I
MPS-12
Model MPS-12 is a fully supervised power supply
that provides the system with preliminary DC
power. Model MPS-12 is rated at 12 Amps, and
is unfiltered and unregulated. Model MPS-12
supplies power to Models PSR-1, MMB-3 and their
expansion modules with power required for
normal operation. Model MPS-12 incorporates
a resettable circuit breaker on the primary input,
and includes a built-in AC-line filter for surge and
noise suppression. Model MPS-12 mounts in the
MXL enclosure back box.
Model ALD-2I is a MXL network-option module that
supplies two (2) intelligent analog circuits utilizing
Fire Safety “I”, “IL”, and FP series intelligent devices.
Model ALD-2I occupies two (2) addresses on the MXL
Network and through the use of unique
communication-protocol devices connected to the
circuits of Model ALD-2I. The circuits are dynamically
supervised by the MXL control panel. Up to 60
programmable input and output devices may be
connected to each of its two (2) circuits. Each circuit
may be wired as Class B (Style 4) or Class A (Style 6).
Controllable Signal Module (CSM-4)
Network Optional Module Card Cage (MOM-4)
CSM-4
MOM-4
The Model MOM-4 Card Cage provides the MXL
main unit or remote units with card slots for
option modules. Each Model MOM-4 supplies
connection space for either two (2) full-width
option modules: (Models ALD-2I, CZM-4, NIM-1R)
or four (4) half-width option modules: (Models
CSM-4, CRM-4, CMI-300, NET-7, REP-1) or a
combination of one (1) full and two )2) half-width
modules.
Network Optional Module Card Cage (MOM-2)
Model CSM-4 provides two (2) fully supervised,
programmable notification-appliance circuits.
Model CSM-4 supplies two (2) Class B (Style Y)
or Class A (Style Z)-type output circuits for the
supervision and control of listed audible or visual
notification appliances such as: horns, bells,
strobes, etc.
Each circuit can provide up to 1.5 amps (24 VDC)
of current to power notification appliances. Model
CSM-4 is also used for Sinorix. Leased line and
municipal-tie connections are also possible with
Model CSM-4.
Controllable Relay Module (CRM-4)
MOM-2
Model MOM-2 provides the MXL main unit,
remote units. Each Model MOM-2 provides space
for one (1) full-width module (Models: ALD-2I,
CZM-4, and NIM-1R) or two (2) half-width
optional modules (Models: CSM-4, CRM-4, CMI300, NET-7, REP-1).
s Industry, Inc.
Building Technologies Division
CRM-4
Model CRM-4 is designed to provide auxiliary control
of building functions such as: door-holder release,
elevator capture, smoke control, lock release, etc.
Model CRM-4 provides four (4) fully programmable
relays. Each relay contains one (1) set of SPDT
contacts rated at 2 amps 30 VDC / 120 VAC resistive.
MXL Components ─ (continued)
Communication Module (NET-4)
Model REP-1 provides the ability to configure the
local or global networks of the MXL panel in a ‘star’
or ‘daisy-chain’ configuration. Model REP-1 provides
two (2) Style 4 or one (1) Style 7 RS-485 network
circuits. Through the use of Model REP-1, the MXL’s
local network (MXL-MXLR) can be expanded up to
64 nodes.
Remote Power Supply (PSR-1)
NET-4
Model NET-4 is a plug-in-type module used to
provide communication between the Fire Safety
MXL panel and various other MXL remote
modules. Model NET-4 is designed to plug into
an edge-connector-type slot on the Model PSR-1
Network Supply. Model NET-4 provides NFPA
Style 4-type communication: fully digital;
RS-485 operating at 19.2K Baud rate.
Style 7 Network Interface Card (NET-7)
NET-7
Model NET-7 is a microprocessor-controlled MXL
network-interface module that allows the wiring
of the MXL RS-485 network in a NFPA Style 7
configuration. Model NET-7 plugs into a half slot
of the Models MOM-2/4 card cage at the MXL
command center (MMB-2) and at the Model PSR-1
or Model MOM-4 slot at the MXL remote units
(MXLR, MXLRV).
PSR-1
Model PSR-1 is a microprocessor-controlled remote
power supply and battery charger for use with the
MXL panel. Model PSR-1 operates in conjunction with
either a Model MPS-6 or MPS-12, providing 6 or 12
Amps of power for use with various MXL modules.
When used with a Model NET-4 or Model NET-7 plugin communication module, Model PSR-1 becomes
a part of the MXL panel’s internal network. Model
PSR-1 acts as an interface between remote-option
modules and the MXL.
Peripheral Interface Driver (PIM-1)
PIM-1
Model NET-7 provides two (2) independent and
fully supervised communication paths, allowing
system operation through an open and short
circuit. Model NET-7 also isolates the power
supplies at each remote unit, providing the ability
to localize ground-fault conditions. The
communication for Model NET-7 operates at
19.2K Baud rate and is fully digital.
Model PIM-1is a MXL option module that provides
a bidirectional, isolated RS-232 port for connection to
peripheral devices, such as: printers, CRTs, VDTs, color
graphics, alphanumeric pagers and remote diagnostics
hardware. Model PIM-1 mounts in the MXL enclosure,
and connects to Model MMB-3, providing a screwterminal block for connection of RS-232. A number of
supervised and non-supervised formats are available for
Model PIM-1.
Network Repeater Module (REP-1)
Output / Input Module (MOI-7)
REP-1
s Industry, Inc.
Building Technologies Division
MOI-7
MXL Components ─ (continued)
Model MOI-7 is a MXL RS-485 network module
that provides a fully programmable serial
interface to Model MOD-16 output drivers and
MID-16 input drivers. When used with Model
MOD-16 drivers, Model MOI-7 provides a serialannunciator output or relay driver. When used
with Model MID-16, Model MOI-7 provides
programmable inputs.
Each Model MOI-7 can operate up to eight (8)
Model MOD-16 drivers and eight (8) Model MID16 drivers simultaneously. Each Model MOD-16
output and Model MID-16 input is independently
programmable, via the MXL custom software.
These inputs can be individually set for: Alarm,
Supervisory, Trouble, Security or Status usage.
Further, the Model MID-16 inputs can also be
configured to provide supervision for lamps driven by
Model MOD-16 outputs. Screw terminals and
connectors are provided on the Model MID-16
modules for interface to monitored devices.
MXL / (V) Standard Size Enclosure (MME-3)
Output Driver (MOD-16)
MME-3
MOD-16
Model MOD-16 is an output-driver module used in
conjunction with Model MOI-7, as a part of the
Fire Safety MXL System. Up to eight (8) Model
MOD-16s can be connected to a Model MOI-7
interface module. Each Model MOD-16 provides
16 open-collector, current-sinking outputs, which
are rated at 24 VDC, 50mA. Model MOD-16
outputs are programmable, via the MXL custom
software.
Programmable Input Driver (MID-16)
The Model MME-3 enclosure set consists of a sheetmetal back box and door with key-lock. Model MME-3
can be used for the MXL System, MXLV Voice Command
Console, MXLR Transponder, MXLRV Voice Transponder
or Amplifier Equipment (via the Model MSR-1 Rail Kit).
To mount MXL / MXLV modules in Model MME-3, the
Model MBR-MP removable-module mounting plate is
required.
Using the Model MBR-MP mounting plate ─ one (1)
Model MMB, or one (1) Model PSR-1, and up to three (3)
expansion card cages (Model MOM or Model OMM) can
be mounted in the Model MME-3 enclosure. When used
to mount MXL amplifiers (Model EL-410), the Model
MBR-MP module is not required. Instead, up to three (3)
Model EL-410 amplifiers may be installed in Model MME3, via three (3) Model MSR-1 Rail Kits. When amplifiers
are mounted in any enclosure, always install Model
MDG-1 grills in the door for proper ventilation.
Model MME-3 is designed for surface of semi-flush
mounting, and includes various knockouts for wire and
conduit entry. The door in the Model MME-3 set has
two (2) cutouts for clear lenses, blank plates or grills ─
depending on the application ─ and contains a key-lock.
MXL MME-3 and MLE-6 Modules
Mounting Plates (MBR-MP)
MID-16
Model MID-16 is an input module used in
conjunction with Model MOI-7, as a part of the
Fire Safety MXL System. Up to eight (8) Model
MID-16s can be connected to a single Model MOI7, along with eight (8) Model MOD-16 outputdriver modules. Each Model MID-16 provides a
non-supervised input, which can monitor
normally open contact devices.
Each Model MID-16 input can be separately used
as a part of the MXL custom programming logic.
s Industry, Inc.
Building Technologies Division
MBR-MP
The MXL /V Module Mounting Plate (Model MBR-MP) is
required for use in both Models MME-3 and MLE-6
enclosures in order to mount all MXL and MXLV
equipment.
MXL Components ─ (continued)
Model MBR-MP is not necessary if Models MME-3
and MLE-6 enclosures are used only for mounting
of amplifiers (Model EL-410D).
Model MBR-3MP allows mounting of an additional three
(3) Model MOM or Model OMM module expansion card
cages.
Model MBR-MP is a removable MXL /V module
mounting plate that allows the Model MME-3 or
Model MLE-6 enclosure to be shipped to the job
site for wiring and conduit installation, while the
system hardware (electronics) is mounted to the
studs on Model MBR-MP ─ pre-wired,
programmed and tested ─ prior to delivery and
installation at the job site. This process allows for
faster, more efficient system start-ups with less
chance of the sensitive electronics being
damaged while field wiring and conduit are
connected to the system enclosure.
Various combinations of hardware can be installed in
Model MLE-6. If only amplifiers are to be installed in
Model MLE-6, no Model MBR-MP or Model MBR-3MP
plates are required. Instead, up to five (5) Model EL410D amplifiers can be installed by using five (5) Model
MSR-1 rail kits.
The Model MBR-MP mounting plate bolts to the
Model MME-3 or Model MLE-6 enclosures for easy
installation on the job site. Model MBR-MP also
has handles to allow easy transport and
mounting. Model The MBR-MP contains mounting
studs for one (1) Model MMB or Model PSR-1; one
(1) Model PIM-1; one (1) Model TBM-2, and up to
three (3) Model MOM or Model OMM card cages
or two (2) card cages and one (1) TSP-40 Printer
(same mounting studs as the Model MBR-2
enclosures).
Model MBR-MP is ordered and shipped separately
from the Models MME-3 and MLE-6 enclosures.
MXL / (V) Large Size Enclosure (MLE-6)
Model MLE-6 can also be used to mount up to three (3)
MXL card cages and two (2) amplifiers. This
configuration would be typical of a remote, voice
transponder cabinet. In this configuration, one (1)
Model MBR-MP would be used in the upper half of
Model MLE-6 to mount the MXL modules, while the
lower half would use two (2) Model MSR-1rail kits to
mount up to two (2) Model EL-410D amplifiers.
Model MLE-6 is designed for surface or semi-flush
Mounting, and includes various knockouts for wire and
conduit entry. The door supplied with the Model MLE-6
set has three (3) cutouts for either clear lenses, blank
plates or grills ─ depending on the application. The door
also contains twp (2) key-locks, which are keyed the
same.
Various combinations of dead-front mounting
plates are possible with the Model MLE-6 enclosure. A
typical MXLV installation would have one (1) Model
MKB-2 at the top, and two (2) Model MHD-3 dead- front
plates in the middle [for 14 VSM / VLM / VFM modules
per plate] and one (1) or two (2) Model MHD-2 lower
dead-front plates.
MLE-6 Optional Card cage Mounting Plate
(MBR-3MP)
MLE-6
The Model MLE-6 enclosure set consists of a sheetmetal back box and door with two (2) key-locks.
Model MLE-6 can be used for the MXL system,
MXLV Voice Command Console, MXLR Transponder,
MXLRV Voice Transponder or Amplifier Equipment
(via the Model MSR-1 Rail Kit.)
To mount MXL/V modules in Model MLE-6, the
Model MBR-MP removable module mounting plate
is required with the Model MBR-3MP option
available for use.
Using the Model MBR-MP mounting plate, one (1)
Model MMB or Model PSR-1 and up to three (3)
expansion card cages (Model MOM or Model OMM)
can be mounted in Model MLE-6. If additional card
cages are required, the Model MBR-3MP optional
card cage mounting plate can also be installed in
Model MLE-6, below Model MBR-MP.
s Industry, Inc.
Building Technologies Division
MBR-3MP
Model MBR-3MP is an optional MXL / MXLV card
cage mounting plate for use exclusively in the
Model MLE-6 enclosure. When installed in the Model
MLE-6 back box, Model MBR-3MP adds the option of
mounting up to an additional three (3) Model MOM or
Model OMM expansion card cages.
Clear Lens (MDL-1)
MDL-1
MXL Components ─ (continued)
Model MDL-1 is a clear Plexiglas® lens that fits in
one (1) of the two (2) openings in the Model MME3 enclosure door, or in one (1) of the three (3)
openings in the Model MLE-6 enclosure door.
Middle Dead-Front Plate for Mounting Switch
and LED / Fan-Control Modules (MHD-3)
One (1) lens is included in the Model MDL-1 package.
Sheet Metal Blank Plate (MDB-1)
MHD-3
MDB-1
Model MDB-1 is a sheet-metal blank plate that fits in
one (1) of the two (2) openings in the Model MME-3
enclosure door, or in one (1) of the three (3) openings
in the Model MLE-6 enclosure door. One (1) blank
plate is in the Model MDB-1 package.
Upper or Middle Dead-Front Panel (MHD-1)
MHD-1
Model MHD-3 is a hinged sheet-metal panel that attaches to
the Model MME-3 or MLE-6 enclosure back box, and fits in
either the middle of the upper sections of the Model MME-3
or MLE-6 enclosures. Model MHD-3 has openings for two
(2) rows of Model VSM-1 Switch Modules; Model VLM-1 LED
Annunciator Modules; Model VFM-1 Fan Control Modules,
or Model VSB-1 Blank Plates.
Model MHD-3 has openings for two (2) rows of Model
VSM-1 Switch Modules; Model VLM-1 LED Annunciator
Modules; Model VFM-1 Fan Control Modules, or Model VSB1 Blank Plates. Each row can mount up to seven (7)
modules, totaling 14 modules for each Model
MHD-3. Model MHD-3 attaches to the backboxes with
screw fasteners, and is hinged for easy access to the
rear of the modules inside the enclosure.
Middle Dead Front Plate for the Switch/LED/
Fan-Control Modules with Printer Cutout (MHD-4)
Model MHD-1 is a hinged sheet-metal panel that
attaches to the Model MME-3 or the MLE-6 enclosure
back box, and fits in the upper or the middle section of
the Model MME-3 back box, or the upper or either of
the two (2) middle sections of the Model MLE-6 back
box.
Model MHD-1 has an opening with a cover plate for
the Model TSP-40 printer (when used), and attaches
to the backboxes with screw fasteners. Once in place,
Model MHD-1 covers and protects modules and wiring;
providing dead-front construction to that area.
Lower Dead-Front Panel (MHD-2)
MHD-2
Model MHD-2 is a hinged sheet-metal panel that
attaches to the Model MME-3 or the MLE-6 enclosure
back box, and fits in the lower section of the Model
MME-3, and on the lower two (2) sections of the Model
MLE-6 back box.
MHD-4
Model MHD-4 is a hinged sheet-metal panel that attaches
to the Model MME-3 or the MLE-6 enclosure back box, and
fits in the middle section of both enclosures.
Model MHD-4 has openings for two (2) rows of Model
VSM-1 Switch Modules; Model VLM-1 LED Annunciator
Modules; Model VFM-1 Fan Control Modules, or Model
VSB-1 Blank Plates. Each row has space to mount four (4)
modules, totaling eight (8) modules for each Model MHD-4.
Model MHD-4 also has a cutout to display the Model
TSP-40 Internal Thermal Strip Printer. Model MHD-4
mounts to the backboxes with screw fasteners, and is
hinged for easy access to the rear of the modules and
inside of the enclosure. When in place, Model MHD-4
covers and protects modules and wiring, providing deadfront construction to that area.
Rail Kit (MSR-1)
Model MHD-2 has no openings and attaches to the
backboxes with screw fasteners. Once in place, Model
MHD-2 covers and protects modules and wiring;
providing dead-front construction to that area.
MSR-1
s Industry, Inc.
Building Technologies Division
MXL Components ─ (continued)
Model MSR-1 is a System 3TM-type rail kit that fits into
either the Model MME-3 or MLE-6 enclosure back box.
Model MSR-1, which comes with a U-bracket and
a Z-bracket, allows the following modules ─ or any
other System 3-type module ─ to be mounted in
a Model MME-3 or Model MLE-6 enclosure:








Model EL-410D amplifier
Model PS-35 power supply
Model BC-35 battery charger
Model MOI-7 I / O interface
Model MID-16 input driver
Model MOD-16 output driver
Model PS-5A power supply
Model SYS3-MPFO
[for mounting the D2300CP fiber-optic interface
modules]
When used in the Model MME-3 enclosure three (3)
Model MSR-1 Rail Kits can be installed to mount up
to three (3) rows for up to three (3) EL-410D
amplifiers. When used in the Model MLE-6, up to five
(5) MSR-1 Rail Kit rows can be installed to allow
mounting for up to five (5) EL-410D amplifiers.
When the Model MLE-6 enclosure is used with the
Model MBR-MP mounting plate for installation of MXL
or MXLV equipment, up to two (2) Model MSR-1 Rail
Kit rows can also be installed in Model MLE-6 for
mounting of either two (2) Model EL-410 amplifiers or
some complement of System 3-type mount modules.
MPS-12 transformer / supply, can accept NET-4 or NET7 network interfaces, and includes diagnostic LEDs
and two (2) system relays. Model PSR-1 mounts in the
upper section of the MXL enclosure back box.
Model RCC-1 is a remotely located MXL annunciator display
module. Model RCC-1 contains an 80-character LCD
display and control keypad (MKB), as well as a PS-5N7
network interface.
Model RCC-1 modules can be located anywhere that
annunciation or control is required. Model RCC-1 can be
programmed for display only, or can provide display and
system control. Remote printers, VDT, or graphics
computers can be located throughout a facility ─ provided
Model PIM-1 is added to Model RCC-1.
UL Listed Parallel Printer (PAL-1)
PAL-1
Model PAL-1 is a UL Listed, supervised parallel-system
printer for the MXL panel. Model PAL-1 connects
to Model MKB-5 to provide the MXL panel with a
UL Listed, supervised parallel-system printer.
B6 Intelligent Control Point (ICP-B6)
Thermal Strip Printer (TSP-40A)
ICP -B6
Model ICP-B6 is a field-mounted output module that is
capable of being programmed to either a remote bell or
horn ─ or to a speaker or telephone zone. Model ICP-B6
communicates with the MXL fire panel, via ALD loop.
TSP-40A
Line-Isolator Module (LIM-1)
Model TSP-40A is a thermal strip printer, designed as
an event-logging device for the MXL panel, providing a
permanent-history report of all system activity. Model
TSP-40A mounts in the MXL enclosure, and its printout
is visible through a window in the locked-door
enclosure. Printouts are automatically spooled on a
take-up reel for easy records storage.
Remote Command Console (RCC-1)
LIM-1
Model LIM-1 is a short-circuit isolator module for use on the
analog loops of the MXL panel. Model LIM-1 is capable of
providing Style 4 or Style 6 wiring of the ALD loop. Multiple
short-circuit isolators can be used on a single ALD loop to
prevent loss of protection in the event of a short circuit.
RCC-1
s Industry, Inc.
Building Technologies Division
MXL Components ─ (continued)
5-Volt Power Supply / Network Interface (PS-5N7)
PS-5N7
Model PS-5N7 is a 5V power supply and MXL localnetwork interface module. Model PS-5N7 is an integral
part of Model RCC-1. Model PS-5N7 can be used to
provide a Style 4 or Style 7 network interface for either
a remote transponder for the MXLV panel (with either
Model TBM-2, ACM-1 and VSM-1 / VLM-1 / VFM-1), or
to drive Model OMM-1 and associated MXLV cards.
5-Volt Power Supply (PS-5A)
Model PS-5A provides 5 Volts for powering Model MOI7. Model PS-5A obtains its power from the 24-Volt
power supply in the MXL system. Models MOI-7 and
PS-5A both mount on System 3 rails, and can also be
mounted externally to the MXL system.
Models MOI-7 and PS-5A typically drive remotegraphics annunciators or monitor foreign systems and
devices.
Network Interface Module (NIM-1W)
NIM-1W
Model NIM-1W allows for the interconnection or
networking of up to 63 MXL panels. Model NIM-1W
provides a RS-485 communications path in either Style
4 or Style 7 wiring configurations. Model NIM-1W
allows MXL panels to have inter-panel logic, as well as
communicate in a peer-to-peer manner. Model
NIM-1W can be programmed via CSGM logic as a
foreign system interface to communicate with
external-building management systems.
s Industry, Inc.
Building Technologies Division
Details for Ordering
Model
Number
ALD-2I
CRM-4
CSM-4
ICP-B6
LIM-1
MBR-MP
MBR-3MP
MDB-1
MDL-1
MHD-1
MHD-2
MHD-3
MHD-4
MID-16
MKB-2
MKB-5
MLE-6
MMB-3
MME-3
MOD-16
MOI-7
MOM-2
MOM-4
MPS-6
MPS-12
MSR-1
NET-4
NET-7
NIM-1W
PAL-1
PIM-1
PS-5N7
PSR-1
RCC-1
REP-1
TSP-40A
Part
Number
Description
500-891618 [2] Two-Loop Analog Driver
500-890401 Programmable Relay [94] Modules
500-890402 Notification Appliance Circuits [2] Module
500-895303 Intelligent Control Output [B6 chip]
500-892361 Short-circuit Line Isolator (ALD)
500-694210 Module Mounting Plate [MME-3, MLE-6]
500-694532 Module Mounting Plate [MLE-6 use only]
500-692070 Blank Metal-Door Inserts
500-692069 Plexiglas® Door Insert
305-092071 Middle / Dead Front / no openings
305-092072 Bottom / Dead Front / no openings
305-092073 Middle / Dead Front [w/ switch openings]
305-092074 Middle / Dead Front [w/ switch, printer openings]
500-891747 16-Input Driver Module
500-892077 Hinged Display /Control Keyboard
500-648727 Multi-Line Display / Control Keyboard
Large Enclosure
500-694530
[holds up to six (6) Model OMM / MOM modules]
500-648860 MXL Main Board, Fast Processor
500-694209 Medium Enclosure [holds up to 6 OMMs/ MOMs]
500-890828 Programmable Output Driver
500-892800 Network I / O Interface [Style 4 or 7]
500-892766 Expansion Card Cage [2 slots]
500-890269 Expansion Card Cage [4slots]
500-490357 MXL 6-Amp Power Supply
500-492209 MXL 12-Amp Power Supply
545-092415 Single-Row Rail Kit for Model MBR-2
500-891181 Style 4 Communication Module
500-091914 Style 7Communication Module
500-699103 Local and Wide-Area Network Interface Module
500-692407
UL Listed, Field-Mounted Parallel Printer
500-691324 Peripheral Interface Module
500-892728 Local Network Interface [Style 4 or 7]
500-891182 Remote Power Supply / Controller
500-692533 Remote Command Display Console
500-892954 RS-485 Network Repeater
500-634933 Thermal Strip Printer
Related Documentation
Product
Data Sheet Number
MXLV
5035
Installation and Operation Manual [IOM]
Model
Number
Part
Number
M-1
315-090725
315-092724
315-092594
315-093336
315-093234
315-095028
315-093329
315-092169
315-093315
315-094547
315-092471
315-092135
315-095921
315-096242
ILI-1 / 1H / 1A / 1AH
ILP-1 / IPLT-1
ILT-1
ILI-1B / 1BH
ILP-2
MSI-10B / 20B
MS-MI
TRI-B6 / B6D / B6R
TRI-B6M
ICP-B6
UM-1
FP-11
TRI-S/D/R
Description
Conventional Zone Module
Intelligent Ion Detectors
Intelligent Photo Detectors
Intelligent Heat Detectors
Intelligent Ion High-Velocity Detectors
FirePrintTM Application-Specific Detection
Intelligent Manual Station
Intelligent Metal Manual Station
Intelligent Monitor Module [single / dual with array]
Intelligent Mini-Monitoring Module
Intelligent Control Output [B6 chip]
Line-Isolator Module
Intelligent FirePrintTM Detector
Intelligent Monitor Module
Note: For further details, refer to MXL IOM manual: 315-092036.
Notice: This marketing data sheet is not intended to be used for system design or installation purposes.
For the most up-to-date information, refer to each product’s installation instructions.
s Industry, Inc.
Building Technologies Division
Fire Safety
8 Fernwood Road
Florham Park, NJ 07932
Tel: (973) 593-2600
FAX: (908) 547-6877
URL: www.usa.Siemens.com/Fire
(SII-FS)
Printed in U.S.A.
Fire Safety
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 / Canada
Tel: (905) 799-9937
FAX: (905) 799-9858
January 2013
Supersedes sheet dated 11/10
(Rev. 3)