8-Port 10/100Mbps + 2-Port Gigabit TP/SFP Combo

ISW-1022M
8-Port 10/100Mbps + 2-Port Gigabit TP/SFP Combo
Managed Industrial Switch
Enhanced Reliability for Industrial Networks
The PLANET ISW-1022M Managed Industrial Ethernet Switch with
multiple redundant ring technology is equipped with 8 10/100Mbps
Fast Ethernet ports and 2 Gigabit TP/SFP combo interfaces delivered in
a rugged high-strength case. It is an industrially (substation) hardened
and fully managed Ethernet Switch specifically designed to operate
reliably in electrically harsh and climatically demanding environments.
The ISW-1022M is the most reliable choice for highly-managed and
Fiber Ethernet application.
■ Redundant Ethernet Network
■ Manageable
■ Power Redundant
■ Gigabit / Fiber uplink capability
Fast Recovery to a Redundant Ethernet Network
The ISW-1022M features strong and rapid self-recovery capability to prevent interruptions and outside intrusions. It incorporates advanced redundant data Ring
technology, Rapid Spanning Protocol (IEEE 802.1w RSTP) and redundant power supply system into customers’ industrial automation network to enhance system
reliability and uptime in the harsh factory environments. It also protects customer’s industrial network connectivity with switching recovery capability that is used
for implementing fault tolerant ring and mesh network architectures. If the Industrial network was interrupted accidentally, the fault recovery times could be
less than 20ms to quickly bring the network back to normal operation.
Tough, Environmentally Hardened Design
With IP-30 aluminum industrial case protection, the ISW-1022M provides a high level of immunity against electromagnetic interference and heavy electrical
surges which are usually found on plant floors or in curb side traffic control cabinets. The ISW-1022M also provides a wide range of power supply options
suitable for multiple industries and for worldwide operation. The feature of operating temperature range from -10 to 60 Degree C allows the Managed
Industrial Switch to be placed in almost any difficult environment.
Robust Layer 2 Features and Advanced Security
The ISW-1022M supports robust advanced features including IEEE 802.1Q VLAN, GVRP, Port link aggregation, QoS, broadcast storm control, MAC address
filtering, IGMP snooping enhanced security and bandwidth utilization to fit a variety of applications. Via aggregation of supporting port, the ISW-1022M allows
the operation of high-speed trunk combining multiple ports. Maximum up to 4 ports of the ISW-1022M can be assigned for 4 trunk groups and support failover as well. Additionally, its standard-compliant implementation ensures interoperability with equipments from other vendors.
Efficient and Centralized Management
The ISW-1022M provides the benefit of efficient and centralized management with the built-in console, WEB and SNMP management interfaces. The Webbased management of the ISW-1022M is an easy-to-use, platform-independent management and configuration facility supporting standard Simple Network
Management Protocol (SNMP) and can be managed via any standard-based network management system. For text-based management, the ISW-1022M can
be accessed via Telnet and the console port. The enhanced system reliability and advanced networking features offered by the ISW-1022M makes it ideally
suited to build the Industrial Ethernet networks for mission-critical and real-time control applications.
Flexibility and Extension solution
The two mini-GBIC slots in the ISW-1022M are compatible with 1000Base-SX/LX/WDM and 100Base-FX through SFP (Small Form Factor Pluggable) fiberoptic transceivers. The fiber optical uplink capability guarantees the throughput to all nodes hooked into the network and the Gigabit Ethernet distance can
be extended from 550 meters (Multi-Mode fiber cable) or up to 10/30/50/70/120 kilometers (Single-Mode fiber or WDM fiber cable). They are well suited for
applications within the factory data centers and distributions.
Easy Installation
The ISW-1022M is packaged in a compact case that allows either DIN rail or panel mounting for efficient usage of cabinet space. It provides an integrated
power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs
for high availability applications requiring dual or backup power inputs.
Data Sheet
1
ISW-1022M
Key Features
Physical Port
Quality of Service
•• 8-Port 10/100Base-TX RJ-45
•• 4 priority queues on all switch ports
•• 2-Port Gigabit TP/SFP combo interface, SFP(Mini-GBIC) supports
100/1000 Dual Mode
•• Traffic classification by:
•• 1 RJ-45 Console interface for Switch basic management and
setup
- Port-Based priority
- IEEE 802.1p Class of Service
- IP TOS (Type of Service) priority
Industrial Conformance
•• 12 to 48V DC, redundant power with polarity reverse protect
function
•• 0 to 60 Degree C operation temperature
•• IP-30 metal case
•• Supports strict priority and Weighted Round Robin (WRR)
policies
•• Ingress/Egress Bandwidth control on each port
Multicast
•• Relay alarm for port breakdown, power failure
•• IGMP Snooping v1 and v2
•• Supports 4000 VDC Ethernet ESD protection
•• IGMP Query mode for Multicast Media application
•• FCC Class A, CE compatibility
•• Free fall, Shock and Vibration Stability
Security
•• IEEE 802.1x Port-Based Authentication
Rapid Ring
•• MAC address Filtering and MAC address Binding
•• Rapid Ring, Dual Homing, Coupling Topology
•• IP address security management to prevent unauthorized
intruder
•• Provides redundant backup feature and the recovery time less
than 20ms
•• Port Mirroring to monitor the incoming or outgoing traffic on a
particular port
Layer 2 Features
•• Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE
802.3z Gigabit Ethernet standards
•• Supports Auto-negotiation and half duplex/full duplex modes
for all 10Base-T/100Base-TX and 1000Base-T ports
•• Auto-MDI/MDI-X detection on each RJ-45 port
•• Prevents packet loss with back pressure (Half-Duplex) and IEEE
802.3x PAUSE frame flow control (Full-Duplex)
•• Supports VLANs
- IEEE 802.1Q Tagged based VLAN
- Port-Based VLAN
- GVRP
- Up to 255 VLANs groups, out of 4K VLAN IDs
•• Supports Spanning Tree Protocol
- STP, IEEE 802.1D Spanning Tree Protocol
- RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
•• Supports Link Aggregation
- Up to 4 Trunk groups
- Up to 4 ports per trunk group with 800Mbps bandwidth (Full
Duplex mode)
- IEEE 802.3ad LACP (Link Aggregation Control Protocol)
- Cisco ether-Channel (Static Trunk)
Data Sheet
2
Management
•• WEB-based, Telnet, Console Command Line management
•• Access through SNMP v1, v2c and v3 set and get requests
•• SNMP Trap / SMTP email for alarm notification of events
•• System Log Server / Client
•• Configuration backup / restore
•• E-mail event alert
•• TFTP firmware upgrade
•• Support LLDP to allow switch to advise its identification and
capability on the LAN
ISW-1022M
Applications
PLANET’s Managed Industrial Ethernet Switch, ISW-1022M, offers high reliability and security to make sure the continuous industrial operation in
harsh environments such as control cabinet of transportation, factory floors, outdoor space, and extreme low or high temperatures. In the industrial
networking environments, each networked device is required to keep running continuously in the hazardous status. If industrial equipment fails
to connect to the network, it might influence the entire operation of industrial systems and thus cause incredible financial losses. By adopting the
ISW-1022M Managed Industrial Switch which complies with all the requirements of industrial applications, customers may enjoy high reliability, fast
recovery capability, and safe Ethernet network operation.
■ Factory Redundant Ring Application
Surveillance
System
Production Area
Production Area
Sludge Pump
PUMP
PLC
I/O
I/O
Classification Area
I/O Devices
PUMP
Management PC
ICS-2100
PLC
Surveillance
System
Industrial
Motors/Drives
ICS-2100
PLC
Pump
ISW-1022M
I/O
PUMP
ROBOT
ISW-1022M
ISW-500
Redundant Ring
Robot
ISW-800
ISW-1022M
Packaging Area
100Base-FX Fiber-optic
100
100Base-TX UTP
1000Base-T UTP
RS-232
■ Transportation Networking and Public Wireless Service
Freeway
Data Center
Outdoor IP Camera
ICA-350
1000
ICA-350
Outdoor IP Camera
ISW-1022M
ISW-511
100
ISW-1022M
Redundant Ring
ISW-1022M
Industrial Fast
Ethernet Switch
100
IGS-501
ISW-802M
WAP-6200
Outdoor
IP Camera
Outdoor IP Camera
Wireless Community
VoIP
Phone
IP Surveillance
Emergency
VoIP Phone
100
100Base-FX Fiber-optic
1000
1000Base-SX/LX Fiber-optic
100Base-TX UTP
1000Base-T UTP
Data Sheet
3
PLANET Technology Corporation
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
Tel: 886-2-2219-9518 Fax: 886-2-2219-9528
Email: sales@planet.com.tw www.planet.com.tw
VoIP Gateway: vip.planet.com.tw
PLANET reserves the right to change specifications without prior notice. All brand names and trademarks are property of
their respective owners. Copyright © 2008 PLANET Technology Corp. All rights reserved.
ISW-1022M
Specification
Product
8-Port 10/100Mbps + 2-Port Gigabit TP/SFP Managed Industrial Switch
Model
Hardware Specification
10/100Mbps Copper Ports
10/100/1000Mbps Copper Ports
SFP/mini-GBIC Slots
Switch Architecture
Switch Fabric
Switch Throughput
Address Table
Share Data Buffer
Maximum Frame Size
Flow Control
ISW-1022M
LED
Console Interface
Power Input
Power Consumption
Operating environment
Storage environment
Dimension ( W x D x H)
Weight
Layer 2 Function
Redundant Ring
Port Configuration
Port Status
VLAN
Spanning Tree
Link Aggregation
QoS
IGMP Snooping
Bandwidth Control
Port Mirror
Security
Data Sheet
4
8 10/ 100Base-TX RJ-45 Auto-MDI/MDI-X ports
2 10/100/1000Base-T RJ-45 Auto-MDI/MDI-X ports
2 1000Base-SX / LX / BX, shared with Port-9~Port-10, compatible with 100Base-FX SFP
Store-and-Forward
5.6Gbps / non-blocking
8.3Mpps
8K entries
1Mbit
1522 Bytes packet
Back pressure for half duplex, IEEE 802.3x Pause Frame for full duplex
Per unit: Power (Green), Power 1 (Green), Power 2 (Green), Fault (Red)
8 port 10/100: Link/Activity (Green), Full duplex/Collision (Yellow)
SFP port: LNK/ACT(Green), 1000T: LNK/ACT(Green), 1000M(Green)
One RJ-45-to –RS-232 male connector for switch management
12 to 48V DC, Redundant power with polarity reverse protection function
8.16Watts max.
-10 ~ 60 Degree C
-40 ~ 85 Degree C
72 x 105 x 152 mm
948g
5 ports for Redundant ring to provide redundant backup feature and the recovery time below 20ms.
It supports ring modes as below:
• Rapid Ring
• Couple Ring
• Dual Homing
Port disable/enable
Auto-negotiation 10/100Mbps full and half duplex mode selection.
Flow Control disable / enable. Bandwidth control on each port.
Display each port’s speed duplex mode, link status, Flow control status. Auto negotiation status
Port-Based VLAN, up to 9 VLAN groups
IEEE 802.1q Tagged Based VLAN , 4K VLAN ID, up to 256 VLAN groups
IEEE 802.1d Spanning Tree
IEEE 802.1w Rapid Spanning Tree
Supports 4 groups of 4-Port trunk support
Traffic classification based on :
• Port Number
• 802.1p priority
• IP DSCP/TOS field in IP Packet
v1 and v2
256 multicast groups and IGMP query
Per port bandwidth control
• Port-1~Port-8 rate range: 100 kbps to 102400 kbps
• Port-9~Port-10 rate range: 100 kbps to 256000 kbps
Storm control
• Broadcast / Multicast / Unknown Unicast packet
RX / TX / Both
Port Security
• Support 100 entries of MAC address for static MAC and another 100 for MAC filter
ISW-1022M
Management
Management Interface
Console, Telnet, Web Browser, SNMP v1, v2c and v3
Support 10 IP addresses that have permission to access the switch management and to prevent
unauthorized intruder
System Event Log
• System Log Server/Client
• SMTP E-mail Alert
• Relay Alarm Output System Events
Provides one relay output for port breakdown, power fail and link down port.
Alarm Relay current carry ability: 1A @ DC 24V
RFC-1213 MIB-II
RFC 1157 SNMP MIB
RFC-2863 Interface MIB
RFC-1493 Bridge MIB
RFC-2674 Extended Bridge MIB (Q-Bridge)
RFC 1643, RFC 1757, RSTP MIB
Private MIB
Management IP Security
System Event Log
Alarm
SNMP MIBs
Standards Conformance
Regulation Compliance
FCC Part 15 Class A, CE
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX / 100BASE-FX
IEEE 802.3z Gigabit SX/LX
IEEE 802.3ab Gigabit 1000T
IEEE 802.3x Flow Control and Back pressure
IEEE 802.1d Spanning tree protocol
IEEE 802.1w Rapid spanning tree protocol
IEEE 802.1p Class of service
IEEE 802.1Q VLAN Tagging
IEEE 802.1x Port Authentication Network Control
IEC60068-2-32 (Free fall)
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
Standards Compliance
Stability
Ordering Information
ISW-1022M
8-Port 10/100Mbps + 2G TP/SFP Combo Managed Industrial Switch
Available Modules
MGB-GT
MGB-SX
MGB-LX
MGB-L30
MGB-L50
MGB-L70
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
1000Base-T Module
1000Base-SX mini-GBIC
1000Base-LX mini-GBIC
1000Base-LX mini-GBIC
1000Base-LX mini-GBIC
1000Base-LX mini-GBIC
MGB-L120
MGB-LA10
MGB-LB10
MGB-LA20
MGB-LB20
MGB-LA40
MGB-LB40
MFB-FX
MFB-F20
MFB-F40
MFB-F60
MFB-FA20
MFB-FB20
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
SFP-Port
1000Base-LX mini-GBIC module-120km
1000Base-LX (WDM,TX:1310nm) mini-GBIC module-10km
1000Base-LX (WDM,TX:1550nm) mini-GBIC module-10km
1000Base-LX (WDM,TX:1310nm) mini-GBIC module-20km
1000Base-LX (WDM,TX:1550nm) mini-GBIC module-20km
1000Base-LX (WDM,TX:1310nm) mini-GBIC module-40km
1000Base-LX (WDM,TX:1550nm) mini-GBIC module-40km
100Base-FX Transceiver (1310nm) -2KM
100Base-FX Transceiver (1310nm) - 20KM
100Base-FX Transceiver (1310nm) - 40KM
100Base-FX Transceiver (1310nm) - 60KM
100Base-BX Transceiver (WDM,TX:1310nm) -20KM
100Base-BX Transceiver (WDM,TX:1550nm) -20KM
Data Sheet
5
module
module
module-30km
module-50km
module-70km
PLANET Technology Corporation
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
Tel: 886-2-2219-9518 Fax: 886-2-2219-9528
Email: sales@planet.com.tw www.planet.com.tw
VoIP Gateway: vip.planet.com.tw
01-09
C-ISW1022M
PLANET reserves the right to change specifications without prior notice. All brand names and trademarks are property of
their respective owners. Copyright © 2008 PLANET Technology Corp. All rights reserved.