CAL-ROYAL
P R O D U C T S, I N C.
C
U®L
US
3 HOUR FIRE RATED
UL10C, UBC7-2-1997
C
U®L
US
CAL-ROYAL
P R O D U C T S, I N C.
3 HOUR FIRE RATED
UL10C, UBC7-2-1997
5
Casted Chassis and Assembly
Minimum Stile requirements
4” escutcheon trims and 4 ½”
for thumbpiece and rose trims
9800EO24 and F9800EO24
ACTUAL
SIZE
20”
MAXIMUM
CUT DOWN
2”
22” to 24” door width
9800EO32 and F9800EO32
28”
6”
26” to 32” door width
MODEL
DOOR SIZE
9800EO36 and F9800EO36
32”
6”
30” to 36” door width
9800EO48 and F9800EO48
44”
12”
36” to 48” door width
C
U®L
US
3 HOUR FIRE RATED
UL10C, UBC7-2-1997
Available. Prefix “ALRM” before part #.
Chassis and Assembly
DIMENSIONS
Touchbar height to finished floor
Touchbar projection
neutral
depressed
Panic grade top & bottom latch case
Fire grade top latch case
Fire grade bottom latch case
Top and bottom rod length for 36” x 84”
lengthrod--length
Short for
2 ’6”
TopDevice
and bottom
48”(8x 14mm)
96”
-- Long 3’8” (1120 mm)
Vertical rods
MODEL
9860V3684, F9860V3684, 9890V3696,
F9890V3696
and 9850V36120
Top and bottom
rod length for 36” x 84” doors
9880V4896, F9880V4896,
Top
and
bottom
rod
length for 48” x 96” doors
9840V48120 and F9840V48120
41” (1034mm) at center
2 ½” (64mm)
1 ¾” (45mm)
3 1515/16
16 ” x 2 ” x 1 ” (100mm x 52mm x 42mm)
11
1
3 1515/16
16 ” x 2 11/16
16 ” (100mm x 68mm x 53mm)
16 ” x 2 1/16
3 1515/16
16 ” x 2 ” x 1 ” (100mm x 52mm x 42mm)
Top rod 37 ½” (955mm), bottom rod 84” (2134mm)
2’2”rod
to 3’
to 914 mm)
door
size
Top
49(840mm
” (1260mm),
bottom
rod
96” (2438mm)
3’2”
to 4’ ( 967
mm tubing
to 1219mm) door size
½” (13mm)
Round
ACTUAL
MAXIMUM
DOOR SIZE
SIZE
CUT DOWN
32”
6”
30” to 36” door width
Top rod 37 ½” (955mm), bottom rod 84” (2134mm)
44”rod 59 ” (1260mm),
12”
36” to
48”
width
Top
bottom
rod
35door
”
(905mm)
84”
(2134mm)
CAL-ROYAL
P R O D U C T S, I N C.
CAL-ROYAL
P R O D U C T S, I N C.
C
U®L
US
3 HOUR FIRE RATED
UL10C, UBC7-2-1997
1 ¾” thick standard. 3 ¾” minimum stile width required for single door
application. 3 ½” minimum stile width required for double door application.
“ALRM” before part #.
DIMENSIONS
Touchbar height to finished floor
Touchbar projection
neutral
depressed
Panic grade top & bottom latch case
Fire grade top latch case
Fire grade bottom latch case
Top and bottom rod length for 36” x 48” doors
Top and bottom rod length for 48” x 96” doors
Vertical rods
MODEL
LBR9860V3684, LBRF9860V3684,
LBR9890V3696 and LBRF9890V3696
LBR9880V4896 and LBR F9880V4896
41” (1034mm) at center
2 ½” (64mm)
1 ¾” (45mm)
3 1515/16
16 ” x 2 ” x 1 ” (100mm x 52mm x 42mm)
15
11
1
3 15/16
16 ” x 2 11/16
16” x 2 1/16
16” (100mm x 68mm x 53mm)
15
3 15/16
16” x 2 ” x 1 ” (100mm x 52mm x 42mm)
Top rod 37 ½” (955mm), bottom rod 84” (2134mm)
Top rod 49 ” (1260mm), bottom rod 96” (2438mm)
½” (13mm) Round tubing
ACTUAL
MAXIMUM
DOOR SIZE
SIZE
CUT DOWN
32”
6”
30” to 36” door width
44”
12”
36” to 48” door width
Alarm Exit Hardware
z z z
Rim Type Exit Devices
ALRM9800EO36
Alarm Rim Type 36” Door (Panic Grade)
ALRM9800EO48
Alarm Rim Type 48” Door (Panic Grade)
FALRM9800EO36
Alarm Rim Type 36” Door (Fire Grade)
FALRM9800EO48
Alarm Rim Type 48” Door (Fire Grade)
Vertical Rod Type Exit Devices
Prefix “ALRM” before PART#
Features
Alarm unit has internal horn. When the push rail is depressed, the horn sounds to provide an audible means
of signaling that the door has been opened and violated.
The unit has changeable 2 minute alarm cutoff or manual reset. Preset at factory for 2 minute alarm cut off.
The key switch to turn alarm off is a standard 1 ¼” cylinder with “C” keyway. The alarm operates on one
standard 9 volt transistor battery. When battery is weak the horn will emit an intermittent signal.
Alarmed units are supplied with a switch that monitors push rail only.
Unit includes “EMERGENCY EXIT ONLY • ALARM WILL SOUND” decal for application on door or unit.
Finishes
Cal-Royal
P
3
4
9
10
10B
26
26D
32
32D
(Refer to Price List for Stock Finishes)
Description
Primecoat
Polished Brass, Clear Powder Coat
Satin Brass, Clear Powder Coat
Polished Bright Bronze
Satin Bronze, Clear Powder Coat
Oil Rubbed Bronze
Polished Bright Chrome
Satin Chrome
Polished Bright Stainless
Satin Stainless
BHMA
600
605
606
611
612
613
625
626
628
630
US
Finish
USP
US3
US4
US9
US10
US10B
US26
US26D
US32
US32D
Material
Steel
Brass
Brass
Bronze
Bronze
Bronze
Brass
Brass
Stainless Steel
Stainless Steel
5
Trim Selection
z z z z z z z z z z z z z
LEVER DESIGN
Non-handed Grade 1 (Clutch Style)
Cylindrical body hardened steel heavy duty tailpiece. For 1 ¾”
and 2 ¼” doors. Prefix THI before part # for 2 ¼” door
thickness. Available for fire and non fire rated rim and
vertical rod exit devices.
Rose diameter 3 ½”, lever length 4 ¾”. Fits and covers 161
cutout.
Other Lever Trim Designs
Finishes: Architectural plated finishes.
Patented Clutch
Freewheeling
ENT00L or
ICENT00L or
ICSCENT00L4
ENTRANCE
8000K
Ball Knob Keylock
TUB DESIGN
Key locks and unlocks lever.
Operates as CLASSROOM
FUNCTION.
ANSI Function – 08
AT DESIGN
STOREROOM
STR05L or
ICSTR05L or
ICSCSTR05L4
PAS30L
Key operates lever, otherwise
always locked.
ANSI Function – 04
PASSAGE
Trim always operable and free.
ANSI Function - 15
DUM40L
DUMMY
Dummy trim. One sided
ANSI Function – 10
SPA DESIGN
When ordering “AT” and “SPA” designs, prefix design name
before part #. Example: ENT00L in “AT” is ATENT00L.
KEYWAY: 6 pin solid brass “C” keyway standard. Optional:
Schlage E, Schlage C-K, Russwin D1-2-3-4, Corbin 59/60,
Sargent LA-LB-LC, Falcon/Weiser E, Arrow 1C, Yale 8, Yale
GA and Kwikset. Can also accept Medeco, Assa and Kaba
High Security Cylinders.
(IC) INTERCHANGEABLE CORE
Interchangeable Core locks will accept compatible 6 or 7 pin
cores with BEST, FALCON and ARROW.
(ICSC) INTERCHANGEABLE CORE: Indicates function
available with Schlage Full size format Interchangeable
Core.
6
8000K
Trim Selection
z z z z z z z z z z z z
ESCUTCHEON LEVER DESIGN
CONSTRUCTION
x Rigid, non clutch mechanism.
x Double heavy duty spring support to prevent
sagging and enhance operation.
x Grade 1, thru-bolted design. Non-handed
design. Easily field reversible.
x Hardened steel heavy duty tailpiece.
Available for fire and non fire rated rim and
vertical rod exit devices.
DOOR THICKNESS
Standard 1 ¾”.
For 2 ¼” thick door use
additional part# TAIL3.
ESCUTCHEON DIMENSIONS
2 ¾” width X 10 ¼” length. Lever length: 4 ¾”.
Fits and covers 2 ESC9800 or
ICESC9800 or
ICSCESC9800
ENTRANCE
ESC9805 or
ICESC9805 or
ICSCESC9805
STOREROOM
ESC9830
Other Lever
Trim Designs
Rigid Entrance, key locks or unlocks escutcheon trim
ANSI FUNCTION (63) Operates as classroom function
Rigid Storeroom, key unlocks lever, lever retracts latch
bolt, otherwise always locked
ANSI FUNCTION (04)
PASSAGE
Trim always operable and free
ANSI FUNCTION (62)
ESC9840
DUMMY
Dummy Escutcheon trim ANSI FUNCTION (10)
ATESC
KEYWAY: 6 pin solid brass “C” keyway Mortise Cylinder standard. Optional: Schlage
E, Schlage C-K, Russwin D1-2-3-4, Corbin 59/60, Sargent LA-LB-LC, Falcon/Weiser
E, Arrow 1C, Yale 8, Yale GA and Kwikset. Can also accept Medeco, Assa and Kaba
High Security Cylinders.
(IC) INTERCHANGEABLE CORE: Interchangeable Core locks will accept
compatible 6 or 7 pin cores with BEST, FALCON and ARROW.
(ICSC) INTERCHANGEABLE CORE: Indicates function available with
Schlage Full size format Interchangeable Core.
RLESC
7
Trim Selection
z z z z z z z z z z z z z
PULL DESIGN
9800 NL
IC9800NL
ICSC9800NL
FOR RIM DEVICES ONLY
Outside by pull and key.
Key retracts latch bolt.
ANSI function – 03
Covers 161 cutout
KEYWAY
6 pin solid brass “C” keyway
Rim Cylinder standard.
9800 DTP
9800 EOP
Outside by pull only.
Pull when dogged.
ANSI function – 02
Covers 161 cutout
Outside by plate only.
Pull when dogged.
ANSI function – 10
Covers 161 cutout
FINISHES
Architectural plated finishes.
THUMBPIECE TRIM
KEYED
(OPERATES ON RIM & VERTICAL ROD DEVICES)
98TP00 or
IC98TP00
ICSC98TP00
ENTRANCE
Key locks or unlocks thumbpiece.
(Operates as classroom function)
ANSI Function – 63
98TP05 or
IC98TP05
ICSC98TP05
STOREROOM
Key unlocks thumbpiece, thumbpiece
retracts latch bolt, otherwise always
lock. ANSI Function-04
PASSAGE
Trim always operable and free.
ANSI Function – 63
DUMMY
Dummy trim. Includes blank Mortise
dummy cylinder. One sided.
ANSI function – 10
98TP30
98TP40
KEYWAY: 6 pin solid brass “C” keyway Mortise Cylinder standard. Optional: Schlage E, Schlage C-K,
Russwin D1-2-3-4, Corbin 59/60, Sargent LA-LB-LC, Falcon/Weiser E, Arrow 1C, Yale 8, Yale GA and
Kwikset. Can also accept Medeco, Assa and Kaba High Security Cylinders.
(IC) INTERCHANGEABLE CORE
Interchangeable Core locks will accept compatible 6 or 7 pin cores with BEST, FALCON and ARROW.
(ICSC) INTERCHANGEABLE CORE: Indicates function available with
Schlage Full size format Interchangeable Core.
FINISHES
Architectural plated finishes.
8
DUMMY
Electrified Lever Trim
zzzz
Cal-Royal’s electrified lever trim provides remote locking and unlocking capabilities while incorporating the patented
clutch trim design. The 24V DC solenoid can be energized from a distant controller, thus allowing access control of the
opening.
The control of stairwells in high-rise buildings is a common application
for this trim, where electric pullback of the exit device’s latch bolt is
cost prohibitive or not required.
This is especially practical in
8
applications
where fire/life safety codes require a “fail-safe” condition
which is not an option with electrified latch pullback devices. Because
the current draw is quite low there is no need for a more expensive
power supply to provide the surge current.
Features
x Continuous duty solenoids used to insure trouble-free operation
x Internally mounted solenoid to ease installation (no special door
prep required)
x No hassle 3-Year Warranty
Options
x Available Fail Safe (electrically locked) or Fail Secure (Electrically
Unlocked)
x Voltage options – 12V or 24V (AC/DC)
x Request to Enter Switch (REE) available
x CRU2 – Current Reduction Unit to improve solenoid life in
“continuously on” applications
Specifications
Solenoid....................Continuous Duty 24VDC
Operating Voltage....12 or 24VAC/DC + OR – 10% (must
specify 12 or 24 volts when ordering)
Amperage................260mA@12V / 160mA@24V
Coil Resistance........12V=49: / 24V=159:
To order, Specify:
OPTIONS: FAIL SAFE (FS)
FAIL SECURE (FSE)
ITEM#
DESCRIPTION
FS12 ESC22
FS12 FAIL-SAFE OPTION 12V AC/DC
FS24 ESC22
FS24 FAIL-SAFE OPTION 24V AC/DC
FSE12 ESC22
FSE12 FAIL-SECURE OPTION 12V AC/DC
FSE24 ESC22
FSE24 FAIL-SECURE OPTION 24V AC/DC
9
(ELR) Electrical Latch Retraction
Our electrified latch pullback exit device allows for remote keyless access control in high occupancy/high traffic
conditions where exit devices are required.
Common applications include conditions such as hospitals, airports,
schools, churches and they are commonly specified in applications that require automatic door openers. The device
may be continuously energized allowing for a push/pull condition if desired.
Features:
x Available on 2200 Series, including rim, vertical rod, concealed vertical rod, fire and non fire-rated devices.
x High-performance quality solenoids designed for demanding applications
x The PM200* interface power module (included) is programmed to meet the requirements of the specific exit
device modification. It maximizes the efficiency and life of the solenoid, allows for a much longer wire run and
may be used with 24VDC power supplies rated at 1.5A or greater
x Dual coil solenoids, or PWM programming, allow for either momentary or extended time latch retraction
x No hassle 3-Year Warranty
Specifications
x Voltage – 24VDC
x Amperage – Surge current – 12A for 200ms@24V / Holding – 250mA@24V
x Coil resistance – 3.7:
To order, specify:
x
Prefix ELR before PART#
Signal Switch RX and LX
RX (request to exit) signal switch is used to signal the use of an opening from the push side. When the push pad is
depressed, the switch is activated. These devices are equipped with an internal SPDT (single pole double throw)
switch that monitors the touch bar.
LX (latch bolt monitoring) signal switch monitors both egress and access of an opening. When the latch bolt is
retracted, the switch is activated. These devices are equipped with an internal SPDT (single pole double throw) switch
that monitors the latch bolt position.
LX and RX switches can be combined.
LX, RX switches can be used in combination with EL (electric latch retraction) option.
Specifications
RX or LX..........Switch rated 0.5 amps @ 24VAC/DC resistive
Low current RX or LX.Switch rated 0.5 amps @ 24VAC/DC resistive
For Factory Installed:
To Order, Specify:
Prefix: - RX..........................Request to Exit switch for field installation
LX...........................Latch Bolt Monitoring switch for field installation
LXRX......................Latch Bolt Monitoring / Request to Exit Combination
10
Heavyduty Keyless Locks
ELECTRONIC CRCODE007
Features
x
x
x
x
x
x
x
x
x
Dual mode for code free entry either mechanically by key or
thru the keypad
Designed for 7700 and 9800 Series
Can store up to 90 different numeric user codes in 4, 5 or 6
Settings remain in memory when batteries are removed
Audible alarm sounds after 3 incorrect attempts
Connections available for remote release switch and
activation when linked to Fire alarm system
Can be used as STOREROOM or CLASSROOM function
Factory default set as STOREROOM function
Fast and easy programming via master code
electronically
digits
automatic lock
MECHANINCAL CRCODE101
Features
x
x
x
x
x
x
x
x
x
Heavy Duty
Designed for 7700 and 9800 Series
Grade 1 Panic Exit Device
Single code (up to 8000 code combinations)
Weather-resistant finish
Code can be changed anytime without dismounting
Full size, non-handed lever handle
Easy Installation
Reversible Handing
CR4000 TRILOGY© KEYLESS EXIT TRIM
Features
x
x
x
x
x
x
x
x
x
Clutch mechanism insures long life and durability
Fingertip and/or Windows Programmable
2000 User Codes: Master, manager, supervisor and users
Real Time Clock for up to 40,000 Event Time/Date-Stamped
Audit Trail
Up to 500 Lock/Unlock Schedules (with Time Zone Support)
Rugged 12-Button Metal Keypad
Non-Handed; Fully Field Reversible
Adaptable to most major manufacturers of standard RIM and
IC RIM Cylinders
Battery operated; uses 5 AA batteries
11
POWER SUPPLIES FOR
ELECTRIFIED EXIT DEVICES
zzzz
The CRPS1N is a heavy duty, high quality, low cost solution for powering a single latch retracting exit device. The solid state design
insures years of trouble-free operation. The power supply delivers raw, unregulated DC current which is ideal for the extreme in-rush
requirement of most solenoid driven electric latch retracting exit devices. The power supply comes housed in a sturdy, yet compact metal
enclosure.
CRPS1N
Features:
x
Power supply delivers the necessary
high current in-rush for a single exit
device
x
Solid-state design eliminates problems
associated with mechanical relays
x
Single input/output
Specifications:
x
Input voltage – 120 VAC
x
Output voltage – 24 VDC unregulated @ 1A
x
Temperature range – 0 to 120F
x
1 Solid-State input/output (input triggered by
dry contact)
x
LEDs – RED = Power indicator
GREEN = Channel on
x
Enclosure dimensions: 10” x 10” x 4”
The CRPS2 Series power supplies are high quality, cost effective solution for powering two electric latch-retracting exit devices. These
power supplies provide the necessary surge current that most latch-retracting exit devices require. The CRPS2 Series offers features
found on power supplies costing much more; and the solid-state design and careful attention to detail make the CRPS2 Series ideal choice
for the discerning user who requires a power supply that can offer years of trouble-free operation.
CRPS2
CRPS2BB
Features:
x
Delivers the necessary in-rush current
to power two latch pullback exit devices.
x
Two independent inputs/outputs
x
Solid-state design eliminates
mechanical problems associated with
relays
x
Thermal overload sensing reduces risk
of failure due to overheating
x
Fire alarm disconnect link
x
Inputs triggered by dry contact
x
Intelligent short circuit detection detects
shorts much faster than fuses and
isolates the short to the individual output
x
Removable Euro-style terminal blocks
allow for easy installation
x
UL Pending at time of print
x
No hassle 3-Year Warranty
Additional Features (CRPS2BB Only):
x
Efficient battery backup/charging circuitry with
zero voltage drop at power loss
x
Solid state reverse polarity protection for
battery connections
x
Audible alert when sensing AC power failure
& low battery (batteries not included)
x
Output Voltage – 24 VDC unregulated @ 2.3A
x
Enclosure dimensions: 12.5” x 15” x 4”
Specifications:
x
Input Voltage – 120 VAC
x
Output Voltage – 24 VDC unregulated @ 2A**
x
Temperature Range – 0 to 120 F
x
1 Solid-State input/output (input triggered by
dry contact)
x
LEDs – Red = Power indicator
GREEN = Channel on
x
Enclosure dimensions: 10” x 10” x 4” **
**CRPS2 only
The CRSW3 power supply is a low cost, regulated switching power supply. It is designed specifically to supply power to low current DC
devices such as mortise locks, cylindrical locks and electric strikes. The CRSW3 supplies 2.4A @ 27VDC and provides (3) non-fused
outputs. The CRSW3 comes housed in a 10” x 10” x 4” sturdy metal enclosure.
CRSW3
12
Features:
x
Adjustable output voltage
(22-27V under load)
x
No hassle 3-Year Warranty
Specifications:
x
Input voltage – 110 or 240VAC
x
Output voltage – 2.4A @ 27VDC
x
(3) Non-fused outputs
x
Enclosure dimensions : 10” x 10” x 4”
CAL-ROYAL
P R O D U C T S, I N C.
C
U®L
US
3 HOUR FIRE RATED
UL10C, UBC7-2-1997
1 ¾”
4 ½”
Alarm..................................... Prefix “ALRM” before PART#
Dogging Feature................... Cylinder dogging available for non rated applications
MODEL SIZE
ACTUAL LENGTH
M98CVR3684 and M98CVR3696
32”
MAXIMUM CUT DOWN
6”
DOOR SIZE
30” to 36” door width
13
CAL-ROYAL
P R O D U C T S, I N C.
C
U®L
US
3 HOUR FIRE RATED
UL10C, UBC7-2-1997
1 ¾”
4 ½” (114mm) min
16
Alarm..................................... Prefix “ALRM” before PART#
Dogging Feature................... Cylinder dogging available for non rated applications
MODEL SIZE
W98CVR3684 and W98CVR3696
14
ACTUAL LENGTH MAXIMUM CUT DOWN
32”
6”
DOOR SIZE
30” to 36” door width
CAL-ROYAL
P R O D U C T S, I N C.
Standard 1 ¾”.
2 5 / ” width X 8 ½” length. Lever length: 4 ¾”. Fits and
ICSCCVRESC9800
ICSCCVRESC9805
2 5/16”
(59)
KEYWAY:!
"$'<>?J'<>Q[J\
]QQ^Q_J `{|}J
'>~Q~€Q~J|Weiser E, Arrow, Yale 8, Yale GA[kQ
!J [‚><'
2 ”
(64)
8 ½”
(216)
(IC) INTERCHANGEABLE CORE: Interhangeable Core loks will pt
atible or 7 pin es with BEST, FALCON and ARROW.
(ICSC) INTERCHANGEABLE CORE: Indiates f
tion available with
Schlage Full size format Intehangeable Core.
15
CAL-ROYAL
P R O D U C T S, I N C.
C
U®L
US
3 HOUR FIRE RATED
UL10C, UBC7-2-1997
4 ½”
1 ¾”
OPTIONAL OPEN
BACK STRIKE
OBSTRKLHR
1 ¾”
Alarm......................................... Prefix “ALRM” before PART#
Dogging Feature....................... Cylinder dogging available for non rated applications
MODEL SIZE
MR9800EO36
MR9800EO48
16
ACTUAL LENGTH
32”
44“
MAXIMUM CUT DOWN
DOOR SIZE
6”
30” to 36” door width
12”
36” to 48” door width
OBSTRKRHR
CAL-ROYAL
P R O D U C T S, I N C.
1 ¾”.
4 ¾”
Key retracts latchbolt
ICSCMRESC9800
ICSCMRESC9805
2”
(50.8)
* MUST USE MR9805EO36/48 Mortise Rim Exit
* MUST USE MR9805EO36/48 Mortise Rim Exit
KEYWAY: Standard 6 pin solid brass “C” keyway, Schlage E,
2 ½”
(64)
8”
(203)
Schlage C-K, Russwin D1-2-3-4, Corbin 59/60, Sargent LA-LB-LC,
Falcon/Weiser E, Arrow, Yale 8, Yale GA and Kwikset. Can Also
accept Medeco, Assa and Kaba High Security Cylinders.
(IC) INTERCHANGEABLE CORE: Interchangeable core locks will accept
compatible 6 or 7 pin cores with BEST, FALCON and ARROW.
(ICSC) INTERCHANGEABLE CORE: Indicates function available with
Schlage Full size format Interchangeable Core.
17
CAL-ROYAL
P R O D U C T S, I N C.
Accessories
N251
2 ½”
2 ¾”
18
Accessories
z z z z z z z
MULLIONS
418 – Removable mullion Aluminum
painted (Prime coat) includes top
and bottom retainer supplied as a
stock 96” for non fire rated
applications.
ICLCK418 - Interchangeable core
locks will accept compatible 6 or 7
pin cores with BEST, FALCON and
ARROW.
2 ½”
424 – Fire exit mullion. 2” x 3” x 96”
steel tubing round corner,
iron
construction with iron top and bottom
retainers. To be used with two rim
type devices on two independent
active doors with full double door
openings.
424 MULLION
4 ” MIN. STILE
ICSCLCK418 - Indicates function
available with Schlage Full size
format Interchangeable Core.
TOP RETAINER
3-1/4”
7/16”
1 ¼”
3-5/8”
4”
3”
1 ½”
LCK418 – Lockable Removable
mullion Aluminum painted (Prime
coat) includes top and bottom
retainer supplied as a stock 96” for
non fire rated applications.
2”
2”
1-3/4”
2”
3/4”
Additional Rods
1-5/16”
Electric lockable mullions are available on request.
3-9/16”
BOTTOM RETAINER
Vertical Rods for 10 feet high doors available on non fire rated vertical rod devices only. Use part#
VRRD-10.
KEYWAYS: 6 pin solid brass “C” keyway standard. Optional: Schlage E, Schlage C-K, Russwin D1-2-3-4
Corbin 59/60, Sargent LA-LB-LC, Falcon/Weiser E, Arrow 1C, Yale 8, Yale GA and Kwikset. Can also
accept Medeco, Assa and Kaba High Security Cylinders.
GLASS BEAD SHIM KITS
801 – For rim type, ” thick
806 – For vertical type, ” thick
812 – Forr fire
fire rated type, ” thick
When exit devices are used with shim kits with outside trim, spidle length thumbpiece and thru bolt length
must be increased accordingly.
CYLINDER DOGGING KITS
TO ORDER: Prefix “CD” before PART#. Available
a 9800 Series devices except fire exit hardware.
for all
Cylin
Cylinder
dogging with mortise cylinder is located on
insert lock bolt in retracted position.
the
h mounting
m
the
To
KIT ONLY: use PART# 36CD9800 for 36”
To order
o
and
and 48CD9800 for 48” devices. Specify finish.
19
18
CAL-ROYAL
P R O D U C T S, I N C.
MODEL #
20
9800 & F9800 Rim Type and Fire Exit Devices
9860 & F9860 Vertical Rod and Fire Exit Devices
ANSI A156.3 Grade 1
Selector Chart
21
6605 Flotilla St., Comerce, CA 90040 U.S.A.
Tel: (323) 888-6601 • FAX: (323) 888-6699
Website: cal-royal.com•Email: sales@cal-royal.com
EXIT DEVICES
COMPARISON CHART
RIM EXIT DEVICE
CONVERSIONS
ARROW
CAL-ROYAL
CORBIN/RUSSWIN
DETEX
DORMA
PRECISION
SARGENT
VON DUPRIN
YALE
RIM EXIT DEVICE
CONVERSIONS
ARROW
CAL-ROYAL
CORBIN/RUSSWIN
DETEX
DORMA
PRECISION
SARGENT
VON DUPRIN
YALE
RIM
VERTICAL
ROD
RIM
VERTICAL
ROD
S1200
2200
ED8200
V4000
8300
5100
2828
22
2100
S1100
2260
ED8400
--8400
5200
2727
2227
2110
S3800
9800
ED5400
10
9300
2100
8800
98
7100
S3700
9860
ED4750
20
9400
2200
8700
9827
7110
RIM
VERTICAL
ROD
RIM
VERTICAL
ROD
--7700
----------99
---
--7760
----------9927
---
1800
4400
ED6000
----100
9898
--1500
----------200
----1510
Distributed by:
22