General Description: Specification

wdmlighting.com
General Description:
Front View
The 400 Watt 24V RGB Controller has programmable
variations of speed, flash and fade time of each
pattern, capable of fading between 2 seconds,
variable to 2 minutes. It has selectable RGB dimming
modes, RGB roll mode, auto-run, DMX mode, slave
mode, sound controlled mode, and special control
mode. The total power consumption for all LED
lights connected is 400 Watts. Connect up to 164
feet of RGB Rope or 65 ft. of Cove Lighting to this
power supply. Additional units can be added to a
second power supply and synchronized together.
Specification:
RGB Controller with Built-In Power Supply
No Additional Power Supply Required
Input Power: 100-240 VAC
Output Power: 4 x DC(24V x 4A)
400 Watt Maximum
Rear View
Dimensions: 14.6 x 9.3 x 2.6 in.
Weight: 8 lbs
Programmable Speed Variations
Color Mixing - 16 Million Colors
Flash - Fade - Color Wash
17 Built-in Programs - DMX - Master/Slave
WDM LIGHTING 2603 OAK LAWN AVE., STE. 120, DALLAS, TX 75219
Lighting Matrix:
CONTROLLER
POWER
RGB PRODUCT
100’ RGB Rope
Per Terminal
400’ Total
100 Watts
Per Terminal
24V 400 Watt
DMX Controller
33’ Starstream
Per Terminal
20 Of The
Colortube 12
Per Terminal
8 Of The
Colortube 39
Per Terminal
Accessories: Front power connectors, end caps, mounting clips and leader cables.
WDM
WD
M LIGH
IIGHTING
GHTI
GH
TING
TI
NG 2
2603
260
603
60
3 OAK
AK LAWN
AWN AVE.,
, STE. 12
120,
0,, DAL
ALLAS
ALLA
LAS
LA
S, T
TX
X 75
7521
75219
219
21
9
CONNECTION
Hard Wire
wdmlighting.com
6 lighting effects modes:
There are six lighting effect modes via the RGB controller.
1. Solid Color Mode:
Press the mode button until you see a sideways T and numbers (usually
255). This will allow you to adjust the brightness level of the red, blue
and green LED’s of your fixtures.
the brightness of red.
Press the up or down button to adjust
You have 0-255 levels of brightness.
Press the function button to adjust the brightness of green.
Follow the
same steps for blue.
2. Colorwash mode:
Press the button until you see SP on the LCD screen and a green dot on
the roll line.
Press the function mode to adjust the flash and speed of
the effect. F stands for flash. For no flash effect, keep at 500. 501 to
599 increases the flash effect with 599 at the fastest.
Press the function
mode again to adjust the speed of the fade effect. When SP is on the
screen, press the up button to increase the speed and the down button
to decrease the speed.
Press the up/down to put the fade effect on red,
blue, green or RGB.
3. Color Change Auto mode:
Press the button until you see SP on the LCD screen and a green dot on
the auto line. Press the function mode to adjust the flash and speed of
the effect.
F stands for flash. For no flash effect, keep at 500. 501-
599 increases the flash effect with 599 at the fastest. Press the function mode again to adjust the speed of the effect. FD will appear on the
screen. The lower the number, the slower the effect.
WDM LIGHTING 2603 OAK LAWN AVE., STE. 120, DALLAS, TX 75219
wdmlighting.com
Mode (continued):
4. Slave Mode:
Press the mode button until you see the slave effect.
This allows the
controller to be controlled by another power supply.
You must connect
a DMX cable in the DMX out of the Master controller to the DMX in of the
Slave controller box.
5. DMX Mode:
Press the mode button to select the DMX mode. Press the function button to select a DMX address or put the DMX running mode into DMX P1
or DMX P2 mode.
6. Sound Mode:
Press the mode button to select the sound activation effect. SU will appear on the screen with sound sensitivity effects from 1-31. Press the
up/down buttons to raise or lower the sound sensitivity effect.
DMX Value Chart
WDM LIGHTING 2603 OAK LAWN AVE., STE. 120, DALLAS, TX 75219
PAGE 03
wdmlighting.com
WDM IR REMOTE
CONTROLLER
Genernal Description:
The IR remote together with our LED lights can
make colorful and dynamic light scenery effects.
It is widely applied to entertainment hall, stage,
social club and outdoor building decoration.
Key Features:
• Designed for quick and easy infrared
wireless control
• Black Out
• Auto Run Button – Automatically run through
all pre-set programs
• Select Program Button – control access to
pre-set programs
• Flash Button – Active strobe function
• DMX Mode – Select different DMX
channel modes
• Sound active button – Run programs in
sound active mode
• Slave Mode – Control in Master/slave
configuration
• Set Address – Set DMX addressing
• R, G & B Buttons – Adjust Red, Green &
Blue LED values
• Number Buttons – Use to set DMX values
• For use up to 30 feet from fixture
• Dimensions (LxWxH): 4.5” x 2” x .25” /
110 x 46 x 7 mm
WDM LIGHTING 2603 OAK LAWN AVE., STE. 120, DALLAS, TX 75219
PAGE 01
wdmlighting.com
WDM IR REMOTE
CONTROLLER
SPECIFICATION:
Battery: 3V fastener battery.
Transmitting IR signal available. The distance available is at most
10m or 32 ft.
Selectable IR signal including RGB dimming, built-in programs, auto running, flash, speed, slave mode, DMX mode and DMX address for different
applications by pushing the buttons which can control the LED lights.
OPERATION:
1) “BLACK OUT” button, set the LED lights power on or power off by
pressing this button.
2) “A” button, set the LED lights in the situation of auto run by
pressing this button.
3) “PROG” button, set the LED lights to run built-in programs by
pressing this button; select the programs—7 color selection, color
jumping and color dream by pressing “+” and “-” buttons.
4) “F” button, set the LED lights flash on or flash off by pressing this
button; increase or decrease the speed of flash by pressing
“+” and “-” buttons.
5) “SP” button, set the LED lights running speed by pressing this button.
This button is available only in the situation of color jumping and color
dream; increase and decrease the speed by pressing
“+” and “-” buttons.
6) “D” button, set the LED lights into DMX mode by pressing this button.
7) “SA” button, set the LED lights into sound activated mode by
pressing this button. (unavailable for outdoor LED lights).
8) “SL” button, set slave mode by pressing this button.
9) “S” “0” “1” “2” “3” “4” “5” “6” “7” “8” “9” buttons, set DMX address for
WDM LIGHTING 2603 OAK LAWN AVE., STE. 120, DALLAS, TX 75219
PAGE 02
wdmlighting.com
WDM IR REMOTE
CONTROLLER
OPERATION (CONTINUED):
The LED lights by pressing these buttons.
For example, set DMX address “245”
I) Press “S” button, then the red LEDs are on, it mean you can start to
set address.
II) Press “2” button, then the green LEDs are on, it means“2”(hundreds place)
setting successful.
III) Press “4” button, then the blue LEDs are on, it means“4”(tens place)
setting successful
VI) Press “5” button, then all the R/G/B LEDs are on, it means“5”(ones place)
setting and the DMX address setting successful
For example, Set DMX address “002”
I) Press “S” button, then the red LEDs are on, it mean you can start to
set address.
II) Press “0” button, then the green LEDs are on, it means“0”(hundreds place)
setting successful..
III) Press “0” button, then the blue LEDs are on, it means“0”(tens place) setting
successful..
IV) Press “2” button, then all the R/G/B LEDs are on, it means“2”(ones place)
setting and DMX address setting successful..
10) “R” “G” “B” “+” and “-” buttons, set the brightness for the
RGB LEDs by pressing these buttons.
Notice: The IR remote is not available when the LED lights controlled by
DMX controller.
WDM LIGHTING 2603 OAK LAWN AVE., STE. 120, DALLAS, TX 75219
PAGE 03