Installation Instructions and User Guide

Sectional And Tilting Door Opener
Installation Instructions and User Guide
FS 1000
1000N
S/N
WARNING
Please read the manual carefully before installation and use.
The installation of your new door opener must be carried out by a technically qualified
or licensed person.
Attempting to install or repair the door opener without suitable technical qualification
may result in severe personal injury, death and / or property damage.
CONTENTS
Important Safety Recommendations...…………………………….……………………………..1
Product Description & Features.............................................................................................2-3
Pre-Installation Recommendations ........................................................................................4
Installation (Wall Bracket & Door Bracket) .............................................................................4
Installation (Steel Track)……………………………………………………………………… .…...5
Installation (Sectional Steel Track Assembly)..........................................................................6
Battery Backup Assembly (optional)................................................................7
Display Menu Instructions
(Plus II)..........................................................................................................8
Programming Instructions....................................................................................................9-19
Terminal Introduction and Application.................................................................................20-21
Manual Disengagement..........................................................................................................22
Maintenance………………………………………………………….………………………..….….22
Technical Specifications………………………………………………………………………....23-24
Parts Listing………………………………….............................................................................25
Common Fault & Solutions ................................................................................................26-27
IMPORTANT SAFETY RECOMMENDATIONS
FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY
RESULT IN SERIOUS PERSONAL INJURY, DEATH AND / OR PROPERTY DAMAGE.
1. PLEASE READ CAREFULLY AND ADHERE TO ALL SAFETY AND INSTALLATION
RECOMMENDATIONS.
2. The opener is designed and manufactured to meet local regulations. The installer must be
familiar with local regulations required in respect of the installation of the opener.
3. Unqualified personnel or those persons who do not know the occupational health and
safety standards being applicable to automatic gates and other doors, must in no
circumstances carry out installations or implement systems.
4. Persons who install or service the equipment without observing all the applicable safety
standards will be responsible for any damage, injury, cost, expense or claim whatsoever
any person suffered as a result of failure to install the system correctly and in accordance
with the relevant safety standards and installation manual whether directly or indirectly.
5. For additional safety we strongly recommend the inclusion of Photo Beam. Although the
opener incorporates a pressure sensitive Safety Obstruction Force system the addition of
Photo Beam will greatly enhance the operating safety of an automatic garage door and
provide additional peace of mind.
6. Make sure that the garage door is fully open & stationary before driving in or out of the
garage.
7. Make sure the garage door is fully closed & stationary before leaving.
8. Keep hands and loose clothing off the opener and garage door all the time.
9. The Safety Obstruction System is designed to work on STATIONARY objects only.
Serious personal injury, death and / or property damage may occur if the garage door
comes into contact with a moving object
10. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
11.
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your local authority or retailer for recycling
advice.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
- WARNING: Important safety instructions. It is important for the safety of persons to follow
all instructions. Save these instructions.
- Do not allow children to play with door controls. Keep remote controls away from children.
- Watch the moving door and keep people away until the door is completely opened or
closed.
- Take care when operating the manual release since an open door may fall rapidly due to
weak or broken springs, or being out of balance.
- Frequently examine the installation, in particular check cables, springs and mountings for
signs of wear, damage or imbalance. Do not use if repair or adjustment is needed since a
fault in the installation or an incorrectly balanced door may cause injury.
- Each month check that the drive reverses when the door contacts a 50 mm high object
placed on the floor. Adjust if necessary and recheck since an incorrect adjustment may
present a hazard, for drives incorporating an entrapment protection system depending on
contact with the bottom edge of the door.
- Details on how to use the manual release.
- Information concerning the adjustment of the door and drive.
- Disconnect the supply when cleaning or carrying out other maintenance.
- The installation instructions shall include details for the installation of the drive and its
associated components.
1
PRODUCT DESCRIPTION & FEATURES
1. Obstruction force adjustment
The minimum force display “1” and it can be adjusted upward. Display “5” means the
maximum force.
2. Travel speed adjustment
“8” appears on the display means the 80% of the travel speed. Display “A” means the
full speed 160mm/s or 200mm/s.
3. Reversal height adjustment
“0” appears on the display means the door will rebound to the top. Display “1~9”
means the door will rebound to the position of the whole travel. One tenth to Nine tenth of the
whole travel etc.
4. Partial open/height
“0” appears on the display means close the partial open function. Display“1~9” means
to set the different partial open position of the whole travel.
5. Transmitter button recognition function
“0” appears on the display means the buttons recognition function is closed. Display“1”
means the buttons recognition function is open.
6. Codes memory quantity
“A” appears on the display means the maximal code memory quantity is 50pcs. Press
UP/DOWN button once, to increase or decrease quantity. The code memory quantity is set on
5pcs*N, N=1~9. (The quantity is the multiple of 5).
7. Maintenance alarm
“b”appears on the display and led light flashes 10 times quickly means the garage door
and motor need total maintenance.
8.
Automatic safety reverse
Automatic stop / automatic reverse are controlled by our software of circuit boards. We
are circumspect to protect your children, pet or other goods.
9.
Soft start / Soft stop
Ramping speed up and down at the start and end of each cycle reduces stress on the
door and opener for longer life, and makes for quieter operations.
10. Auto-Close
Auto- Close ensures peace of mind and keeps your house secure by automatically closing
the door upon entering or exiting the garage.
11.
Self learning open and close obstruction force
The amount of opener power for different stages of the door’s travel is learnt during setup
and is constantly re-profiled. Opener force measurement automatically adjustment in a
suitable range.
12.
Electronic limit, simple adjustment.
You only need control the limit setup from control panels to adjust it exactly, the simple
and quick process for any peoples.
13. Available terminal for Photo beams & Extra receivers & Wire or wireless wall switch
& Caution light & Pass door protection device.
14.
Energy saving - L.E.D courtesy light
3 minutes L.E.D light delay, switching on with each cycle to illuminate your darkened
garage.
2
15.
Battery backup available
Openers could be supplied power with our battery backup once the power failure at your
home.
16.
Self-Lock in gear motors
Gear motor will self-lock with its disengagement systems.
17.
Manual release
Don't worry about the power failure, the manual release system is a solution for operation
the door at any time.
18.
Transmitter technology
Rolling Code technology (7.38 x 1019 Combinations), 433.92 MHz frequency, 4 channels
design to ensure you can control 4 different doors with one transmitter.
19.
Applications
With as little as 30mm required between the ceiling and the highest point of the door travel,
the opener can be flush mounted for low headroom applications.
20.
Metal bottom plate, stronger and security.
21.
Up / Down moving operation buttons (UP / DOWN)
Open
Close
3
PRE-INSTALLATION RECOMMENDATIONS
1. Garage door must be able to be lifted and closed easily by hand and without much effort. A
well balanced & sprung door is critical for proper installation.
2. The garage door opener can’t compensate for a badly installed garage door and should
not be used as a solution for a “hard to open” door.
3. If the unit is being installed on an existing door, make sure any existing locking devices are
removed or warranty will be void.
4. An approved outlet must be installed near where the opener is begin installed.
5. There should be a minimum gap of 30mm between the bottom of the chain drive rail and
the top of the garage door at its closest point. (refer to Fig 1.)
Important note: As for additional safety rules, we strongly recommends the fitting of Photo
Electric safety beams on all installations.
Figure 1
INSTALLATION INSTRUCTIONS
Mount Wall Bracket and Door Bracket (Fig2)
Wall Bracket - Close the garage door and measure the
garage door width at the top and mark the centre. Locate and
mount the wall bracket 2cm-15cm above the door on the
inside wall.
(Depend on the actual installation space).
Door Bracket – Fix the door bracket to a structural part of the
door as close to the top edge as possible.
Figure 2
4
Installation (Steel Track)
Figure 3
STEP1 (Fig.3)
Attach the opener head to the steel track. Assembly the 2 “U” Hanging brack ets
with 6mm nuts supplied.
STEP2 (Fig.3)
Place the steel track and opener head assembly centrally on the garage f loor, with
the open head furthest away from the door. Lift the front of the track up to the door
bracket. Insert the pivot pin and secure it with the split pin supplied.
STEP3 (Fig.3, Fig.4)
Lift and support the opener head (with a ladder) so it is
positioned centrally and level. Fix the opener and track
on ceiling by Iron bracket A & B.
WARNING: Do not allow children around the door,
opener or supporting ladder serious injury and/or
damage may result from failure to follow this warning.
STEP4 (Fig.3, Fig.5)
Connect the straight arm to the bent arm with the bolt.
Position and bolt the arms to the top edge of the door using
the bolt supplied.
STEP5
Lift the garage door until the shuttle locks into the
drive chain/belt.
Now, ready to program the openers.
5
Sectional Steel Track Assembly
2 Parts Steel Track
A:1500 mm
B:1500 mm
Sleeve
3 Parts Steel Track
D:1000 mm
C:1000 mm
E:1000 mm
Sleeve
Sleeve
1. 2-Parts Track:
As Fig.6, slide the A rail into the sleeve, slide the B rail into the sleeve.
3-Parts Track:
As Fig.7, slide the C rail into the sleeve, slide the D rail into the sleeve; slide the E rail into
the sleeve.
2. Cut the plastic thread; pull the screw rod along with inner chain to the end rail position
(Fig.8)
F
F
3. As Fig.9, release the nut & spring.
4. Tight the nut to the right position as shown in Fig.10, cut the plastic tape, cut the plastic
thread on sprocket, then whole rail assembled finished.
6
Battery backup Assembly (optional)
Option 1 - Top Fixed
STEP1 (Fig.11)
Assemble the battery & battery bracket like the photo, fix by screws supp lied.
STEP2 (Fig.12)
Join the battery to opener, find the Fig.12.
Figure 11
Figure 12
Option 2 - Side Fixed
STEP1 (Fig.13)
Assemble the battery & battery bracket like the photo, fix by screws supplied .
STEP2 (Fig.14)
Join the battery to opener, find the Fig.14.
Figure 13
Figure 14
7
DISPLAY MENU INSTRUCTIONS
FEATURES SETTINGS:
a)Press and hold SET button until “1” appears on the display then release
the button.
b)Press UP / Down button, then it displays the number “1-E”.
c)Press Set button to confirm the feature you need to set, then it enters to
the interface for detail setting of the appointed feature.
d)In the detail setting interface display “0-A” with flash dot.
e)Press UP / Down button to choose the feature you need to set.
f )Press SET button to confirm the set and it will back to standby status
automatically and display “ll”.
8
PROGRAMMING INSTRUCTIONS
Pre- Instruction for programme buttons
1. Short click SET button : When it standby, it will clear the error, alarm display, and
return to normal display.
2. Short click CODE button :

( In the Setting Status) Exit the current operation and return to the standby
interface.
 When it standby, press the code, A dot will be indicated in the corner, now
entering the code leaning mode.
Now first click the button on the hand transmitter you want to use, the dot may
disappear ,then press again the same button on the hand transmitter, the dot will flash,
here, the code learning is finished.
3. Short press UP button : The door will open.
4. Short press DOWN button : The door will close.
(When the door is opening or closing, it will stop if you press any key.)
5. Long press SET button : Enter function setting interface.
6. Long press CODE button : Press and hold CODE button until a C is indicated on the
display. All stored remotes will be deleted.
7. Long press UP button : Increase the resilience. (Keep press DOWN button, after 4
seconds, it will scroll to display 0-1-2, choose the number you want. 1=increase 25%
2=increase 50%)
8. Long press DOWN button : Restore Factory Settings
Keep press DOWN button, after 4 seconds, it will scroll to display
, then the
garage door opener will restart.
Restart means all settings are back to factory settings, all learning things need to be done
again except the transmitter code learning.
9
PROGRAMMING INSTRUCTIONS
1. PROGRAMMING OPEN & CLOSE LIMITS
a) Press and hold SET button to enter this function setting
until “1” appears on the display then release the button.
b) Press the SET button again. The door opener is now in
Programming Mode. And then you will see “n” with dot
appears on the display.
c) Press and hold the UP button until the door reaches the
desired open position, you will see “n” without dot on the
display.
d) Press SET button to confirm the open position, then you
will see “u” with dot on the display.
e) Next press and hold the DOWN button until the door
reaches the desired close position, you will see “u” without
dot on the display.
NOTE: For fine adjustments toggle UP & DOWN
buttons.
f) Now press the SET button to confirm the close position,
then you will see “II” on the display.
After confirm the close position, the door will now cycle open
and close to set the travel limits and force sensitivity
adjustments. The door is now set for normal operation.
CAUTION: After the cycle open and close, there will be
figures shown on the display (0~9), “0” means the doors is
balanced, the smaller figure means the better door balance,
strongly recommend that the figure need to be smaller than
the power force.
10
2. OBSTRUCTION FORCE ADJUSTMENT
CAUTION: The obstruction force adjustment is set automatically
during programming. Normally no adjustment is necessary.
a) Press and hold SET Button until “1”appears on the display, next
press the UP Button until “2” appears on the display to enter this
function setting then release the button.
Increase force
b) Press the SET button again, The unit is now in force adjustment
mode. And then you will see a figure “3” with flash dot appears on the
display.
c) Press the UP button to increase the force setting or the DOWN
button to decrease the force setting.
Decrease force
The minimum force is “ 1 ” and it can be adjusted upward. The
maximum force is “5”.
d) PressSPEED
SET button
to confirm the set and it will back to standby
3. TRAVEL
SETTING
CAUTION: If you changed the speed again, it will cancel the
status automatically and display “ll”.
previous travel limit. The speed adjustment function will be
available only after you reset the travel limit.
NOTE: The force is set on “3” as standard in factory.
a) Press and hold SET Button until “1”appears on the display, next
press the UP button until “3” appears on the display to enter this function
setting then release the button.
Increase speed
b) Press the SET button again. The unit is now in speed adjustment
mode. And then you will see a letter “A” with flash dot appears on the
display.
c) Press the UP & DOWN button to choose the speed. Figure “8”
means the 80% of the travel speed. Figure “A” means the full speed.
Decrease speed
d) Press SET button to confirm the set and it will back to standby
status automatically and display “ll”.
NOTE: The travel speed is set on full speed “A” as standard in factory.
11
4. AUTOMATIC CLOSING&TIME SETTING
NOTE: We recommend that Safety Photo Beams be used in any
installation where the Auto Close function is enabled.
a) Press and hold SET Button until“1”appears on the display, next
press the UP button until “4” appears on the display to enter this function
setting then release the button.
b) Press the SET button again, the unit is now in automatic close
Increase time
adjustment mode. And then you will see a figure “0” with flash dot
appears on the display.
c) Press UP / Down button once to set the auto close time (0~9).
d) Press UP button to increase the time, or DOWN button to decrease
Decrease time
the time.
The close time is 15second*N, N=0~9. The maximum time is 135s. To
disable Auto Close Function, set time to zero (0).
e) Press SET button to confirm the set and it will back to standby
status automatically and display “ll”.
NOTE:
1.The closing time is set on “0” as standard in factory.
2. If the Photo Cell Function is on, and it ’ s broke by the
obstruction, the auto close time will stop for a while, and then continue the
automatic close time again.
12
5. AUTOMATIC CLOSING CONDITION SETTING
a) Press and hold SET Button until “1” appears on the display, next
press the UP button until “5” appears on the display to enter this
function setting then release the button.
b) Press the SET button again. The unit is now in automatic close
condition adjustment mode. And then you will see a figure “1” with flash
dot appears on the display.
Increase
c) Press UP / Down button once to set the auto close condition. You
can choose “1” or “2” set.
Figure “1” means, the door only can auto close while in the open
Decrease
limit position.
Figure “2” means, the door can auto close while the door is in any
position.
d) Press SET button to confirm the set and it will back to standby
status automatically and display “ll”.
NOTE:
TheDELAY
closing TIME
condition
is set on “1” as standard in factory.
6. LED1.
OFF
SETTING
2. The door will only automatic close while in its opening process,
a) Press and hold SET Button until “1” appears on the display, next
but can’t automatic close after it is stopped while in its closing process.
press the UP button until “6” appears on the display to enter this
function setting then release the button.
b) Press the SET button again. The unit is now in LED off delay time
adjustment mode. And then you will see a figure“3”with flash dot appears
Increase time
on the display.
c) Press UP / Down button once to set the LED off delay time (1~9).
d) Press UP button to increase the time, or DOWN button to
decrease the time.
The delay time is 1 minute*N, N=1~9. The maximum delay time is 9
Decrease time
minutes.
e) Press SET button to confirm the set and it will back to standby
13
status automatically and display “ll”.
7. REVERSAL HEIGHT SETTING
a) Press and hold SET Button until “1” appears on the display, next
press the UP button until “7” appears on the display to enter this function
setting then release the button.
b) Press the SET button again. The unit is now in reversal height
Increase height
adjustment mode. And then you will see a figure “0” with flash dot appears
on the display.
c) Press UP / Down button once to set the reversal height while closing
(0~9).
d) Press UP button to increase , or DOWN button to decrease.
Decrease height
Figure “0” means the door will rebound to the open limit position.
Figure “1~9” means the door will rebound to the position of the whole
travel. One tenth to Nine tenth of the whole travel etc...
e) Press SET button to confirm the set and it will back to standby status
automatically and display “ll”.
NOTE: The reversal height is set on “0” as standard in factory.
14
8. PARTIAL OPEN/HEIGHT SETTING
a) Press and hold SET Button until “1” appears on the display, next
press the UP button until “8” appears on the display to enter this
function setting then release the button.
Increase
b) Press the SET button again. The unit is now in partial-open/height
adjustment mode. And then you will see a figure “0” with flash dot
appears on the display.
c) Press UP / Down button once to select if you want to open the
partial open function or set the partial open height. (0~9). Press UP
button to increase , or DOWN button to decrease.
Decrease
Figure “0” means close the partial open function.
Figure “1~9” means set the partial open position of the whole travel.
One tenth to Nine tenth of the whole travel etc...
d) Press SET button to confirm the set and it will back to standby
status automatically and display “ll”.
15
9. TRANSMITTER BUTTONS RECOGNITION FUNCTION SETTING
a) Press and hold SET button to enter this function setting until “9”
appears on the display then release the button.
b) Press the SET button again. The unit is now in buttons recognition
function adjustment mode. And then you will see a figure “1” with flash dot
appears on the display.
c) Press UP / Down button once to select if you want all the 4 buttons
can control the only one opener, or only the separate coded button can
control the opener.
Figure “0” means the buttons recognition function is closed. It means
if you coded 1 button with 1 opener, then all the 4 buttons on the
remote can control the opener. It’s suit for the users who only have 1
Buttons recognition function is closed
automation door at home.
Figure “1” means the buttons recognition function is open. If you
coded first button with first opener, then the first button will be the only
button on the remote can control the opener. It’s suit for the users who
Buttons recognition function is open
have more than 1 automation doors/gates at home.
d) Press SET button to confirm the set and it will back to standby status
automatically and display “ll”.
NOTE: 1. The buttons recognition is set on “1” as standard in factory.
A. CODES MEMORY QUANTITY SETTING
2. After you changed the buttons un-recognition into recognition,
a)
Press
and only
holdthe
SET
Button
untilcan
“1”control
appears
the display, next
please notice that
coded
button
the on
opener.
press the UP button until “A” appears on the display to enter this function
setting then release the button.
b) Press the SET button again, the unit is now in remote quantity
adjustment mode. And then you will see a figure “A” again, but with flash dot
appears on the display.
Increase quantity
c) Press UP / Down button once to set the remote quantity. (A or 1~9).
d) Figure “A”means the maximal quantity 50pcs. Press UP/DOWN
button once to increase or decrease quantity.
Decrease quantity
The remote quantity is set on 5pcs*N, N=1~9. (The quantity is the
multiple of 5)
e) Press SET button
to confirm the set and it will back to standby status
16
automatically and display “ll”.
NOTE: The remote quantity is set on “A” as standard in factory.
b. REVERSAL HEIGHT IGNORANCE SETTING
a) Press and hold SET Button until “1” appears on the display, next
press the UP button until “b” appears on the display to enter this function
setting then release the button.
b) Press the SET button again. The unit is now in reversal height
ignorance adjustment mode. And then you will see a figure “1” with flash
Increase height
dot appears on the display.
c) Press UP / Down button once to set the reversal height ignorance
while closing (0~9).
d) Press UP button to increase , or DOWN button to decrease.
Decrease height
Figure “1~9” means the door will still not rebound even though
there’s obstacles in its closing path within 1cm~9cm away from the
close position. This function is most suitable for the Northern
Europe where will always snow on the ground.
e) Press SET button to confirm the set and it will back to standby
status automatically and display “ll”.
C. PASS DOOR SWITCH TYPE SETTING
a) Press
and hold
SETisButton
appears inonfactory.
the display, next
NOTE:
The reversal
height
set onuntil
“1” “1”
as standard
press the UP button until “C” appears on the display to enter this function
setting then release the button.
b) Press the SET button again. The unit is now in the pass door switch
type adjustment mode. And then you will see a figure “0” with flash dot
appears on the display.
c) Press UP / Down button once to set the pass door switch type. You
can choose “0” or “1” set.
Figure “0” means, the pass door function is normally open.
Figure “1” means, the pass door function is normally close.
17
e) Press SET button to confirm the set and it will back to standby
d. PHOTO CELL ON/OFF SETTING
NOTE: Make sure the photo cell has been correctly installed and used
Normally Closed contacts to the accessory terminals of the opener.
Also note that the photo beam function must be disabled if NO photo
beams are fitted, otherwise the door cannot be closed, and the LED
display will show the letter“ r ”as an indication.
a) Press and hold SET Button until “1” appears on the display, next
press the UP button until “d” appears on the display to enter this function
setting then release the button.
b) Press the SET button again. The unit is now in the photo cell ON/OFF
adjustment mode. And then you will see a figure “0” with flash dot appears
on the display.
c) Press UP / Down button once to set the photo cell ON/OFF switch.
You can choose “0” or “1”set.
Figure “0” means, the photo cell function is closed.
Figure “1” means, the photo cell function is open.
d) Press SET button to confirm the set and it will be back to standby
status automatically and display “ll”.
NOTE: The photo cell is set on “0” as standard in factory.
18
E. MAINTENANCE ALARM--OPERATION CYCLES COUNT SETTING
a) Press and hold SET Button until “1” appears on the display, next
press the UP button until “E” appears on the display to enter this function
setting then release the button.
b) Press the SET button again. The unit is now in the maintenance alarm
adjustment mode. And then you will see a figure “0” with flash dot appears
on the display.
c) Press UP / Down button, you can select the operation cycles you
need the opener to make you notice. You can choose from “1-5” set.
Figure “1” means, after garage door operated to 1000 times, the L.E.D
light will flash 10 times quickly after the door stop working every time.
In order to make you notice that your garage door need to do
maintenance . And at the same time, you will see a figure “t” appears
on the display.
Figure “2” means the maintenance alarm count cycle is set on 2000
times.
Figure “3” means the maintenance alarm count cycle is set on 3000
times.
Figure “4” means the maintenance alarm count cycle is set on 4000
times.
Figure “5” means the maintenance alarm count cycle is set on 5000
times.
c) Press SET button to confirm the set and it will be back to standby status
automatically and display “ll”.
NOTE: 1. The operation cycles count is set on “0” as standard in factory.
F. OPEN
2./ “b”
STOP
appears
/ CLOSE
on display
TERMINALS
and led light flashes 10 times quickly
means the door lost balance, strong recommend the maintenance for garage
The O/S/C facility can be used for an external push button switch to operate
doors.
the opener.
The switch
must have
voltage free
open
contacts.
3. “Check”
the status,
or “ Re-learn”
thenormally
travel limit
after
maintenance
alarm cautions.
19
Photo beam connection (optional) – Fig.15,Fig.16
Switch control connection (optional) – Fig.15
Remark:
1. Flash (Caution Light) Should be less than 25W.
2. PB (External Push Button) Should be “ NO”.
Figure 15
Figure 16
Other terminal introduction and application
1.The O/S/C interfaces available.
(Fig. 17, Fig. 18)
Add a new O/S/C button to open or close the door.
2.
Flash light function. (Fig. 17, Fig. 18)
There are corresponding interfaces for this function and provide 24v-35v flash light voltage.
Connect the flash light with DC 24v-28v, current≤100mA. When use AC 220V power flash
lights, please match an adapter, and wiring as required
3.
Pass door (SD) protection (Fig. 17, Fig. 18)
This function ensures that the door can’t be opened unless the small pass door is closed.
The door panel won’t be damaged.
20
Figure 17
Figure 18
21
MANUAL DISENGAGEMENT
The opener is equipped with a manual release cord to disengage shuttle and move door by
hand while holding the handle down (Fig 19). Pull on the handle to disengage the shuttle. To
re-engage the door simply run opener in automatic mode or move door by hand until the trolley
engages in the chain shuttle.
In some situations that a pedestrian door is not in state, it is recommended that an external
disengagement device should be fitted (Fig 20).
Figure 19
Figure 20
MAINTENANCE
1.
No particular maintenance is required for the logic circuit board.
Check the door at least twice a year if it is properly balanced, and all working parts are in
good working condition or not.
Check the reversing sensitivity at least twice a year, and adjust if it is necessary.
Make sure that the safety devices are working effectively (photo beams, etc.)
2.
Light bulb replacing:
Notice: Make sure the power supply has been cut off before replacing the light bulb. And
ensure the voltage of the new light bulb is in accordance with the local voltage and the
power is within 25 Watt.
Demount the screws on the lamp cover. Take the lamp cover away then twist off the old
L.E.D light anti-clockwise. Fix the new L.E.D light and lamp cover.
3. Before installing a caution light, please ensure the rate is within 5 Watt.
4.
Regarding the maintenance alarm function, LED light flashes 10 times quickly means the
door lost balance, strong recommend the maintenance for garage doors. “Check” the
status, or “ Re-learn” the travel limit after maintenance alarm cautions.
Notice: A rude operating door can affect the life of the automatic opener due to incorrect
loads, and will void the warranty.
22
TECHNICAL SPECIFICATIONS
FS 600
FS 1000
Input voltage
FS 1200
220 - 240V / 110 - 127V, 50–60 Hz
Max. pull force
600 N
1000 N
1200 N
Max. door area
10.0 ㎡
15.0 ㎡
18.0 ㎡
80 kg
100 kg
130kg
Max. door height
2400 - 3500mm
2400 - 3500mm
2400 - 3500mm
Drive mechanism
Chain / Belt
Chain / Belt
Chain / Belt
160mm / Second
160mm / Second
140mm / Second
Max. door weight (Balanced)
Opening / Closing speed
L.E.D
Limit setting
24V / 15pcs LED bulbs
Electronic
Transformer
Radio frequency
Electronic
Electronic
Overload protection technology
433.92 MHz
433.92 MHz
433.92 MHz
Rolling code (7.38 x 1019 Combinations)
Coding format
Status display transmitter
2X
2X
Code storage capacity
2X
50 different codes
Caution light terminal
Included
Included
Included
Working temperature
-40℃ - +50℃
-40℃ - +50℃
-40℃ - +50℃
Safety protection
Soft start & Soft stop, photo cell option, caution light option
Protection level
FS 600
IP20
IP20
FS 1000
FS 1200
23
IP20
FS 600-Speed
Input voltage
FS 1000-Speed
220 - 240V / 110 - 127V, 50–60 Hz
Max. pull force
600 N
1000 N
Max. door area
10.0 ㎡
15.0 ㎡
80 kg
100 kg
Max. door height
2400 - 3500mm
2400 - 3500mm
Drive mechanism
Chain / Belt
Chain / Belt
200mm / Second
200mm / Second
Max. door weight (Balanced)
Opening / Closing speed
L.E.D
24V / 15pcs LED bulbs
Limit setting
Electronic
Transformer
Radio frequency
Coding format
Status display transmitter
Electronic
Overload protection technology
433.92 MHz
433.92 MHz
Rolling code (7.38 x 1019 Combinations)
2X
Code storage capacity
2X
50 different codes
Caution light terminal
Included
Included
Working temperature
-40℃ - +50℃
-40℃ - +50℃
Safety rotection
Protection level
FS 600-Speed
Soft start & Soft stop, photo cell option, caution light option
IP20
FS 1000-Speed
24
IP20
PARTS LISTING
Item
Qty
Top cover
13
1
1
L.E.D cover
14
3
1
L.E.D light
4
1
5
Description
Item
Qty
Transformer
25
1
Chain wheel
1
Chain/ Belt rail
26
2
Mounting bracket
15
1
Chain/ Belt connection
27
1
C rail- steel
PCB-1
16
1
Trolley assy
28
1
Click bracket
1
Control panel cover-2
17
1
Straight arm
29
2
U hanging bracket
6
1
Control panel cover-1
18
1
Bent arm
30
1
Motor shaft sleeve
7
1
Panel label
19
2
Transmitter
31
1
Sprocket assy
8
1
PCB-2
20
1
Transmitter bracket
32
1
Caution card
9
1
Main cover
21
1
Door bracket
33
1
Release handle
10
1
DC gear motor
22
1
Wall bracket
11
1
Steel bottom base
23
1
Track ending bracket
12
1
Transformer plate
24
1
Wheel bracket
Item
Qty
1
1
2
Description
25
Description
Common Fault & Solutions
Fault appearance
Fault cause
Solutions
No any working for openers
1. Power supply
1. Check whether the motor socket is energized
LCD screen is not bright
2. Plug wire is loosing
2. Check whether Fuse tube is broken
3. Check whether the low-voltage wire of transformer is
connected to the power board
4. Check whether the ribbon cable is plugged
5. Check whether there is 26v AC at the transformer
low-voltage side, if there is 26v AC, replace the PCB. If not,
replace the transformer
Position missing
System error
Re-set the limit traveling
While learning, the digital display
Travel less than 30cm or more than 9m
Re-set the limit traveling
Digital display
Insufficient voltage
Check the power supply
The Garage door system is in poor condition
The garage door and motor need total maintenance
Opener does not work or stop working
Digital display
and needs maintenance
LED light will flash quickly for 10 times
Digital display
The gear motor can not self-lock well
Replace the gear motor
Opener is not working
Fail to learn the up and down limit setting
Learn “UP” and “DOWN” limit traveling again follow the manual
Digital display
Improperly learn the up and down limit setting
LED is always on
The control panel is broken or the power
Replace the control board or power board.
supply board is broken
When remoting the door,
Hall sensor wire is loosed or damaged
Open the cover, check the Hall sensor wire, re-plug or replace.
Opener does not work.
The wire between gear motor and board
Open the cover and check the wire between gear motor and
Hear the relay 'kaka' sound
is loosing
board.
Opener stops automatically after running
The wire between gear motor and board is
Power off firstly, open the cover and reverse the plug wire
10cm
plugged inversely
between gear motor and board. Re-set limit traveling.
opener stops automatically after running
10cm
Digital display
Digital display
Digital display
26
Door is up moving only.
Photo cell function has been effective
Turn off the photo cell function if there is no any
Do not work in down moving and the
but without connecting any photo cell device.
photo cell device connected. ( Refer the instruction manual)
Digital display
2. Check if the photo cell is connected correctly, or if there is
any obstruction between the photo cell.
The door is fully open, automatically close
Automatic closing function is turned on
after some time
function.
LED lights flash 4 times
When the door stops, the caution light is
Set the automatic closing time, or turn off the automatic closing
( Refer the instruction manual)
The power board is broken
Replace the power board
1. The LED wire is not plugged
1. Check the LED wire
2. The LED is broken
2. Replace the LED
3. The circuit board is broken
3. Replace the circuit board
Door is automatically reversed to the
In operation with automatic reverse function
1.Check the block position of the door and re-set the limit
upper limit before the door closed
The door is not installed correctly
traveling
completely
There is some block on its moving
2. Increased force number for automatic reverse
Door automatically stops while opening
In operation with automatic protect function
1.Check the block position of the door and re-set the limit
when obstruction is detected
traveling
The door is not installed correctly
2. Increased force number for automatic reverse
always on
LED lights do not work
There is some block on its moving
The remote control cannot be used or the
1. Flat battery
1. Replace new battery
operation distance is short
2. Antenna is loosed or not well extended
2. Extended the antenna on the opener
3. Interference around nearby
3. Get rid of interference
New remote control is not compatible with
Choose our remote control only
Cannot code in the new remotes
opener
Digital display
Stored remote code is full
Delete all stored codes
(Refer the instruction manual)
Door in door function effects
Check the door in door switch
Motor shaft sleeve worn
Replace the motor shaft sleeve
1. Flat battery
1. Charge the battery
2. The battery wire is plugged inversely
2. Open the cover, check “+” “-” of the battery
3. The battery wire is broken
3. Replace the battery wire
External devices is not compatible with the
Remove all the external devices. If the abnormal issues still
opener
exist, replace the circuit board
The Garage door system needs maintenance
The garage door and motor need total maintenance
Standby, Digital display
The opener is working while the door is
not moving
The battery do not supply power
Other abnormal issues
Digital display
27