1 From your mobile device, go to www.GarminConnect.com
/vivofit.
2 Select the App Store button or the Google Play™ button, and
follow the on-screen instructions.
SM
vívofit Owner's Manual
®
Introduction
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Always consult your physician before you begin or modify any
exercise program.
Getting Started
To get the most out of your vívofit device, Garmin recommends
setting it up with your computer or compatible mobile device.
1 Go to www.GarminConnect.com/vivofit.
2 Select an option:
• If you are using a computer to set up your device, plug the
wireless USB ANT Stick™ into an empty USB port, and
download and install the Garmin Express™ setup software
(Downloading the Software, page 1).
• If you are using a mobile device to set up your device,
install and open the Garmin Connect™ Mobile app
(Downloading the Mobile App, page 1).
3 Select the device key À to turn on the device.
®
Sending Data to Your Computer
Before you send data to your computer, you must plug the USB
ANT Stick into a computer USB port, and you must download
the Garmin Express setup software (Downloading the Software,
page 1).
1 Bring the device within 3 m (10 ft.) of your computer.
2 Hold the device key until SYNC appears.
3 View your data at Garmin Connect.
Pairing Your Device with Multiple Computers
You can pair your vívofit device with multiple computers. For
example, you can pair your vívofit device with your home and
work computers. Go to buy.garmin.com, or contact your Garmin
dealer for information about optional accessories and
replacement parts.
1 Plug the USB ANT Stick into a computer USB port.
2 Download the Garmin Express setup software for Windows
or Mac (Downloading the Software, page 1).
3 Hold the device key until PAIR appears.
4 Follow the instructions on your computer to pair your vívofit
device and complete the setup process.
If
5 necessary, repeat steps 1 through 4 for each additional
computer.
Synchronizing Your Data with the Garmin
Connect Mobile App
When you turn on the device for the first time, it is in pairing
mode. If your device is not in pairing mode when you turn it
on, you must hold the device key until PAIR appears.
NOTE: Until you pair your device and complete the setup
process, the device has limited functionality.
4 Follow the instructions on your computer or mobile device to
pair your vívofit device and complete the setup process.
5 Synchronize your step count with your Garmin Connect
account (Sending Data to Your Computer, page 1)
(Synchronizing Your Data with the Garmin Connect Mobile
App, page 1).
Downloading the Software
1 From your computer, go to www.GarminConnect.com/vivofit.
2 Select an option:
• If you are using a Windows operating system, select
Download for Windows, and follow the on-screen
instructions.
• If you are using a Mac operating system, select
Download for Mac, and follow the on-screen instructions.
®
®
Downloading the Mobile App
You can use the Garmin Connect Mobile app to pair your vívofit
device and complete the setup process. This allows you to
share and analyze data and download software updates from
your mobile device. Unlike other Bluetooth devices that are
paired from the Bluetooth settings on your mobile device, your
vívofit device must be paired directly through the Garmin
Connect Mobile app.
NOTE: Your mobile device must support Bluetooth Smart in
order to pair with your vívofit device and synchronize data. Go to
www.garmin.com/ble for compatibility information.
®
You should synchronize your data regularly to track your
progress in the Garmin Connect Mobile app.
1 Bring the device within 3 m (10 ft.) of your mobile device.
2 Hold the device key until SYNC appears.
3 View your current data in the Garmin Connect Mobile app.
Pairing Multiple Mobile Devices
You can pair your vívofit device with multiple mobile devices.
For example, you can pair your vívofit device with a smartphone
and a tablet.
1 Install and open the Garmin Connect Mobile app on your
mobile device (Downloading the Mobile App, page 1).
2 Hold the device key until PAIR appears.
3 Follow the instructions on your mobile device to pair your
vívofit device and complete the setup process.
4 If necessary, repeat steps 1-3 for each additional mobile
device.
Wearing the Device
TIP: Your device comes with an optional keeper that can be
placed on the clasp side of the band.
1 Select a band that fits best on your wrist (Replacing the
Band, page 5).
2 Make sure the pegs on the clasp are fully inserted into the
band.
When both pegs are fully inserted, the device fits securely
against your wrist.
3 Slide the keeper over the clasp (optional).
The keeper is a small loop designed to fit over both ends of
the band and the clasp. It helps keep the band attached.
November 2017
190-01699-00_0F
sleep movement. You can set your normal sleep hours in the
user settings on your Garmin Connect account. You can view
your sleep statistics on your Garmin Connect account.
Using Sleep Tracking
4 Wear the device all day (Using Sleep Tracking, page 2).
Icons
Icons appear at the bottom of the display. Each icon represents
a different feature. You can select the device key to cycle
through the different device features.
The total number of steps taken for the day.
GOAL
The number of remaining steps needed to reach your step
goal for the day. The device learns and proposes a new goal
for you at the beginning of each day.
KM or MI The distance traveled in kilometers or miles for the current
day.
The amount of total calories burned for the current day,
including both active and resting calories.
The current time of day and date based on your location. The
device updates the time and date when you synchronize
your device to a computer or mobile device.
Your current heart rate and heart rate zone from a paired
heart rate monitor.
Auto Goal
Your device creates a daily step goal automatically, based on
your previous activity levels. As you move during the day, the
device counts down the number of remaining steps in your daily
goal. When you reach your step goal, the device displays
GOAL+, and begins counting the number of steps taken that
exceed your daily goal.
If you choose not to use the auto goal feature, you can set a
personalized step goal on your Garmin Connect account.
Before you can use sleep tracking, you must be wearing the
device.
1 Hold the device key until SLEEP appears.
2 When you wake, hold the device key to exit sleep mode.
NOTE: If you forget to put the device into sleep mode, you
can enter your sleep and wake times manually into your
Garmin Connect account to recover your sleep statistics.
Garmin Connect
You can connect with your friends on your Garmin Connect
account. Garmin Connect gives you the tools to track, analyze,
share, and encourage each other. Record the events of your
active lifestyle including runs, walks, rides, swims, hikes, and
more.
You can create your free Garmin Connect account when you
pair your device with your phone using the Garmin Connect
Mobile app, or you can go to www.GarminConnect.com/vivofit.
Track your progress: You can track your daily steps, join a
friendly competition with your connections, and meet your
goals.
Store your activities: After you complete and save a timed
activity with your device, you can upload that activity to your
Garmin Connect account and keep it as long as you want.
Analyze your data: You can view more detailed information
about your activity, including time, distance, heart rate,
calories burned, and customizable reports.
NOTE: Some data requires an optional accessory such as a
heart rate monitor.
Move Bar
Sitting for prolonged periods of time can trigger undesirable
metabolic state changes. The move bar reminds you to keep
moving. After one hour of inactivity, the move bar À appears.
Additional segments Á appear after every 15 minutes of
inactivity.
Share your activities: You can connect with friends to follow
each other's activities or post links to your activities on your
favorite social networking sites.
Manage your settings: You can customize your device and
user settings on your Garmin Connect account.
You can reset the move bar by walking a short distance.
History
Your device keeps track of your daily steps, calories burned,
sleep statistics, and optional ANT+ sensor information. This
history can be sent to your Garmin Connect account.
Your device stores your fitness activity data for up to 3 weeks.
NOTE: When using a heart rate monitor, your data storage is
significantly reduced (approximately 12 days).
When the data storage is full, the devices deletes the oldest files
to make room for new data.
®
Sleep Tracking
While you are sleeping, the device monitors your movement.
Sleep statistics include total hours of sleep, sleep levels, and
2
Device Settings
You can customize your device settings and user settings on
your Garmin Connect account. From your devices widget, select
Device Settings.
Time Format: Sets the device to display time in a 12-hour or 24hour format.
Units: Sets the device to display the distance traveled in
kilometers or miles.
Visible Screens: Allows you to customize the screens your
device displays.
Auto Goal: Allows your device to determine your step goal
automatically.
NOTE: When you disable this feature, you must enter your
step goal manually.
vívofit Owner's Manual
Custom Step Length: Allows your device to more accurately
calculate the distance traveled using your custom step
length.
Heart Rate: Allows you to estimate your maximum heart rate
and determine custom heart rate zones.
ANT+ Heart Rate Monitor
Your device can be used with wireless ANT+ sensors. For more
information about compatibility and purchasing optional sensors,
go to http://buy.garmin.com.
Putting On the Heart Rate Monitor
NOTE: If you do not have a heart rate monitor, you can skip this
task.
NOTE: The device may cause chafing when used for long
periods of time. To alleviate this issue, apply an anti-friction
lubricant or gel to the center of the module where it contacts
your skin.
NOTICE
Do not apply anti-friction gel or lubricant on the electrodes.
Do not use gels or lubricants that contain sunscreen.
You should wear the heart rate monitor directly on your skin, just
below your sternum. It should be snug enough to stay in place
during your activity.
1 Push one tab À of the strap through the slot Á in the heart
rate monitor module.
2 Press the tab down.
3 Wet the electrodes  on the back of the module to create a
strong connection between your chest and the heart rate
monitor module.
NOTE: If your device was packaged with a heart rate monitor,
the heart rate data screen is already enabled and the heart rate
monitor is paired.
1 Put on the heart rate monitor.
2 Bring the device within 3 m (10 ft.) of the sensor.
NOTE: Stay 10 m (33 ft.) away from other ANT+ sensors
while pairing.
Select
the device key until HEART appears.
3
When the sensor is paired with your device, your heart rate
and heart rate zone appear.
Stopping a Heart Rate Activity
Your device creates and saves a fitness activity when it receives
heart rate data, which can be sent to your Garmin Connect
account.
Hold the device key to stop recording heart rate data.
The device displays HEART OFF.
About Heart Rate Zones
Many athletes use heart rate zones to measure and increase
their cardiovascular strength and improve their level of fitness. A
heart rate zone is a set range of heartbeats per minute. The five
commonly accepted heart rate zones are numbered from 1 to 5
according to increasing intensity. Generally, heart rate zones are
calculated based on percentages of your maximum heart rate.
Fitness Goals
Knowing your heart rate zones can help you measure and
improve your fitness by understanding and applying these
principles.
• Your heart rate is a good measure of exercise intensity.
• Training in certain heart rate zones can help you improve
cardiovascular capacity and strength.
If you know your maximum heart rate, you can use the table
(Heart Rate Zone Calculations, page 5) to determine the best
heart rate zone for your fitness objectives.
If you do not know your maximum heart rate, use one of the
calculators available on the Internet. Some gyms and health
centers can provide a test that measures maximum heart rate.
The default maximum heart rate is 220 minus your age.
Device Information
4 Wrap the strap around your chest and attach it to the other
side of the heart rate monitor module.
vívofit Specifications
Battery type
Two user-replaceable CR1632 batteries
Battery life
1+ yr.
Operating temperature
range
From -10º to 60ºC (from 14º to 140ºF)
Radio frequency/protocol 2.4 GHz ANT+ wireless communications
protocol
Bluetooth Smart wireless technology
Water rating
The Garmin logo should be right-side up.
5 Bring the device within 3 m (10 ft.) of the heart rate monitor.
5 ATM*
*The device withstands pressure equivalent to a depth of 50 m.
For more information, go to www.garmin.com/waterrating.
Heart Rate Monitor Specifications
After you put on the heart rate monitor, it is active and sending
data.
Battery type
User-replaceable CR2032, 3 volts
Battery life
Approximately 3 years (1 hour per day)
Pairing Your ANT+ Heart Rate Monitor
Operating temperature From -10° to 50°C (from 14° to 122°F)
range
Before you can pair your heart rate monitor, you must enable
the heart rate data screen on your vívofit device. For more
information about customizing the device screens, see Device
Settings, page 2.
vívofit Owner's Manual
Radio frequency/
protocol
2.4 GHz ANT+ wireless communications
protocol
Water rating
1 ATM*
NOTE: This product does not transmit heart
rate data while swimming.
3
*The device withstands pressure equivalent to a depth of 10 m.
For more information, go to www.garmin.com/waterrating.
User Replaceable Batteries
Replacing the Heart Rate Monitor Battery
1 Locate the circular battery cover on the back of the heart rate
monitor.
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Replacing the vívofit Device Batteries
Before you can replace the device batteries, you must obtain
two CR1632 batteries.
1 Remove the module from the band.
2 Use a coin to twist the cover counter-clockwise until it is
loose enough to remove (the arrow points to OPEN).
Remove
the cover and the battery.
3
4 Wait 30 seconds.
5 Insert the new battery with the positive side facing up.
NOTE: Do not damage or lose the O-ring gasket.
6 Use a coin to twist the cover clockwise back into place (the
arrow points to CLOSE).
After you replace the heart rate monitor battery, you may need
to pair the heart rate monitor with the device again.
Device Care
2 Use a small Phillips screwdriver to remove the four screws on
the front of the module.
3 Remove the cover and batteries.
NOTICE
Avoid extreme shock and harsh treatment, because it can
degrade the life of the product.
Avoid pressing the keys under water.
Do not use a sharp object to clean the device.
Avoid chemical cleaners, solvents, and insect repellents that can
damage plastic components and finishes.
Thoroughly rinse the device with fresh water after exposure to
chlorine, salt water, sunscreen, cosmetics, alcohol, or other
harsh chemicals. Prolonged exposure to these substances can
damage the case.
Do not place in high temperature environments, such as a
clothes dryer.
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Cleaning the Device
1 Wipe the device using a cloth dampened with a mild
4 Apply a small amount of petroleum jelly to each side of the
new batteries using a cotton swab.
5 Insert the new batteries.
NOTE: Do not damage or lose the gasket.
6 Replace the front cover and the four screws.
7 Tighten the four screws equally and firmly.
8 Insert the module into the band.
The device key on the module must be aligned with the key
on the band.
detergent solution.
2 Wipe it dry.
Caring for the Heart Rate Monitor
NOTICE
A build up of sweat and salt on the strap can decrease the ability
of the heart rate monitor to report accurate data.
• Rinse the strap after every use.
• Hand wash the strap occasionally, using a tiny amount of
mild detergent, such as dishwashing liquid.
NOTE: Using too much detergent may damage the strap.
• Do not put the strap in a dryer.
• When drying the strap, hang it up or lay it flat.
Troubleshooting
My device won't turn on
If your device no longer turns on, you may need to replace the
batteries.
Go to Replacing the vívofit Device Batteries, page 4.
4
vívofit Owner's Manual
I don't have a computer or mobile device
Software Update
You can turn on the device and use it with limited functionality,
until you complete the setup process on a computer or mobile
device. Prior to setup, you can use only the step count, auto
goal, move bar, and heart rate monitor (if packaged with your
device). Your device resets your step count once a day. The
device attempts to reset your step count while you are sleeping,
based on your inactivity level from your first day of use. Your
device does not store any history data until setup is complete.
Set up the device on a computer or compatible mobile device
(Getting Started, page 1) to use additional device features.
NOTE: Setup is a one-time process, and it allows you to use
all available device features.
When a software update is available, your device automatically
downloads the update when you synchronize your device with
your Garmin Connect account.
A countdown appears during the update process. When the
update is complete, your device restarts.
Zone % of
Maximum
Heart Rate
Perceived Exertion
Benefits
My device does not display the correct time
1
50–60%
Relaxed, easy pace,
rhythmic breathing
Beginning-level
aerobic training,
reduces stress
2
60–70%
Comfortable pace,
slightly deeper
breathing, conversation
possible
Basic cardiovascular
training, good
recovery pace
3
70–80%
Moderate pace, more
difficult to hold
conversation
Improved aerobic
capacity, optimal
cardiovascular training
4
80–90%
Fast pace and a bit
Improved anaerobic
uncomfortable, breathing capacity and
forceful
threshold, improved
speed
5
90–100%
Sprinting pace,
unsustainable for long
period of time, labored
breathing
The device updates the time and date when you synchronize
your device to a computer or mobile device. You should
synchronize your device to receive the correct time when you
change time zones, and to update for daylight saving time.
1 Confirm that your computer or mobile device displays the
correct local time.
Select
an option:
2
• Synchronize your device to a computer (Sending Data to
Your Computer, page 1).
• Synchronize your device to a mobile device
(Synchronizing Your Data with the Garmin Connect Mobile
App, page 1).
The time and date are updated automatically.
Turning on the Device
Select the device key À.
Replacing the Band
1 Remove the module from the band.
2 Insert the module into the replacement band.
The device key on the module must be aligned with the key
on the band.
Appendix
Heart Rate Zone Calculations
Anaerobic and
muscular endurance,
increased power
Software License Agreement
BY USING THE DEVICE, YOU AGREE TO BE BOUND BY THE
TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE
LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT
CAREFULLY.
Garmin Ltd. and its subsidiaries (“Garmin”) grant you a limited
license to use the software embedded in this device (the
“Software”) in binary executable form in the normal operation of
the product. Title, ownership rights, and intellectual property
rights in and to the Software remain in Garmin and/or its thirdparty providers.
You acknowledge that the Software is the property of Garmin
and/or its third-party providers and is protected under the United
States of America copyright laws and international copyright
treaties. You further acknowledge that the structure,
organization, and code of the Software, for which source code is
not provided, are valuable trade secrets of Garmin and/or its
third-party providers and that the Software in source code form
remains a valuable trade secret of Garmin and/or its third-party
providers. You agree not to decompile, disassemble, modify,
reverse assemble, reverse engineer, or reduce to human
readable form the Software or any part thereof or create any
derivative works based on the Software. You agree not to export
or re-export the Software to any country in violation of the export
control laws of the United States of America or the export control
laws of any other applicable country.
Limited Warranty
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY HAVE OTHER LEGAL RIGHTS,
WHICH VARY FROM STATE TO STATE (OR BY COUNTRY
OR PROVINCE). GARMIN DOES NOT EXCLUDE, LIMIT OR
SUSPEND OTHER LEGAL RIGHTS YOU MAY HAVE UNDER
THE LAWS OF YOUR STATE (OR COUNTRY OR
PROVINCE). FOR A FULL UNDERSTANDING OF YOUR
RIGHTS YOU SHOULD CONSULT THE LAWS OF YOUR
STATE, COUNTRY OR PROVINCE.
vívofit Owner's Manual
5
Non-aviation products are warranted to be free from defects in
materials or workmanship for one year from the date of
purchase. Within this period, Garmin will, at its sole option,
repair or replace any components that fail in normal use. Such
repairs or replacement will be made at no charge to the
customer for parts or labor, provided that the customer shall be
responsible for any transportation cost. This Limited Warranty
does not apply to: (i) cosmetic damage, such as scratches, nicks
and dents; (ii) consumable parts, such as batteries, unless
product damage has occurred due to a defect in materials or
workmanship; (iii) damage caused by accident, abuse, misuse,
water, flood, fire, or other acts of nature or external causes; (iv)
damage caused by service performed by anyone who is not an
authorized service provider of Garmin; (v) damage to a product
that has been modified or altered without the written permission
of Garmin, or (vi) damage to a product that has been connected
to power and/or data cables that are not supplied by Garmin. In
addition, Garmin reserves the right to refuse warranty claims
against products or services that are obtained and/or used in
contravention of the laws of any country. Garmin navigation
products are intended to be used only as a travel aid and must
not be used for any purpose requiring precise measurement of
direction, distance, location or topography. Garmin makes no
warranty as to the accuracy or completeness of map data.
This Limited Warranty also does not apply to, and Garmin is not
responsible for, any degradation in the performance of any
Garmin navigation product resulting from its use in proximity to
any handset or other device that utilizes a terrestrial broadband
network operating on frequencies that are close to the
frequencies used by any Global Navigation Satellite System
(GNSS) such as the Global Positioning Service (GPS). Use of
such devices may impair reception of GNSS signals.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, THE WARRANTIES AND REMEDIES CONTAINED IN
THIS LIMITED WARRANTY ARE EXCLUSIVE AND IN LIEU
OF, AND GARMIN EXPRESSLY DISCLAIMS, ALL OTHER
WARRANTIES AND REMEDIES, WHETHER EXPRESS,
IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING
WITHOUT LIMITATION ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, STATUTORY REMEDY OR OTHERWISE. THIS
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY HAVE OTHER LEGAL RIGHTS, WHICH VARY
FROM STATE TO STATE AND FROM COUNTRY TO
COUNTRY. IF IMPLIED WARRANTIES CANNOT BE
DISCLAIMED UNDER THE LAWS OF YOUR STATE OR
COUNTRY, THEN SUCH WARRANTIES ARE LIMITED IN
DURATION TO THE DURATION OF THIS LIMITED
WARRANTY. SOME STATES (AND COUNTRIES AND
PROVINCES) DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
IN NO EVENT SHALL GARMIN BE LIABLE IN A CLAIM FOR
BREACH OF WARRANTY FOR ANY INCIDENTAL, SPECIAL,
INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER
RESULTING FROM THE USE, MISUSE OR INABILITY TO
USE THIS PRODUCT OR FROM DEFECTS IN THE
PRODUCT. SOME STATES (AND COUNTRIES AND
PROVINCES) DO NOT ALLOW THE EXCLUSION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
If during the warranty period you submit a claim for warranty
service in accordance with this Limited Warranty, then Garmin
will, at its option: (i) repair the device using new parts or
previously used parts that satisfy Garmin's quality standards, (ii)
replace the device with a new device or a refurbished device
that meets Garmin's quality standards, or (iii) exchange the
device for a full refund of your purchase price. SUCH REMEDY
SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY
BREACH OF WARRANTY. Repaired or replaced devices have
a 90 day warranty. If the unit sent in is still under its original
warranty, then the new warranty is 90 days or to the end of the
original 1 year warranty, whichever is longer.
Before seeking warranty service, please access and review the
online help resources available on support.garmin.com. If your
device is still not functioning properly after making use of these
resources, contact a Garmin Authorized service facility in the
original country of purchase or follow the instructions on
support.garmin.com to obtain warranty service. If you are in the
United States, you can also call 1-800-800-1020.
If you seek warranty service outside of the original country of
purchase, Garmin cannot guarantee that the parts and products
needed to repair or replace your product will be available due to
differences in product offerings and applicable standards, laws
and regulations. In that case, Garmin may, in its sole discretion
and subject to applicable laws, repair or replace your product
with comparable Garmin products and parts, or require you to
ship your product to a Garmin Authorized service facility in the
country of original purchase or to a Garmin Authorized service
facility in another country that can service your product, in which
case you will be responsible for complying with all applicable
import and export laws and regulations and for paying all custom
duties, V.A.T., shipping fees and other associated taxes and
charges. In some cases, Garmin and its dealers may be unable
to service your product in a country outside of the original
country of purchase or return a repaired or replaced product to
you in that country due to applicable standards, laws or
regulations in that country.
Online Auction Purchases: Products purchased through online
auctions are not eligible for rebates or other special offers from
Garmin warranty coverage. Online auction confirmations are not
accepted for warranty verification. To obtain warranty service,
an original or copy of the sales receipt from the original retailer
is required. Garmin will not replace missing components from
any package purchased through an online auction.
International Purchases: A separate warranty may be provided
by international distributors for devices purchased outside the
United States depending on the country. If applicable, this
warranty is provided by the local in-country distributor and this
distributor provides local service for your device. Distributor
warranties are only valid in the area of intended distribution.
Australian Purchases: Our goods come with guarantees that
cannot be excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. The benefits under
our Limited Warranty are in addition to other rights and remedies
under applicable law in relation to the products. Garmin
Australasia, 30 Clay Place, Eastern Creek, NSW 2766,
Australia. Phone: 1800 235 822.
support.garmin.com