Dotz TPar System
©2015 ADJ Products, LLC all rights reserved. Information,
specifications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsufficient and negligent assembly,
installation, rigging, and operation of this product.
User Instructions
Rev. 2/15
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn off all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Dotz TPar System
Introduction
Unpacking: Thank you for purchasing the Dotz TPar System by ADJ
Products, LLC. Every Dotz TPar System has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate
the unit has arrived intact. In the case damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Do not return this unit to your dealer without first
contacting customer support.
Introduction: The Dotz TPar System is part of ADJ’s continuing pur-
suit for creating high quality affordable intelligent fixtures. The Dotz
TPar System is a high performance, DMX intelligent, moving head LED
fixture. This fixture is a great piece for retail stores, displays, mood,
architectural, interior and exterior decoration, and clubs. This unit can
be used as a stand alone, or in a Master/Slave configuration. The unit
can also be controlled via DMX controller. This fixture is suitable for
theaters, studios, retail stores, and other similar locations.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
Dotz TPar System
General Instructions
To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
Dotz TPar System Features
• 4 x COB LED Par Wash Fixtures
1 x Foot Controller
1 x Lighting Stand
1 x RF Remote Control
1 x Stand Bag
1 x Soft Case for Lighting System
• RGB Color Mixing
• Strobing
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• Five DMX Modes: 3 Channel Mode, 5 Channel Mode, 9 Channel Mode, 12 Channel Mode, & 18 Channel Mode
•4 Operating Modes - Sound Active, Auto Run, Built-In Programs, or DMX Control
• Power Cord Daisy Chaining (See Page 21)
Dotz TPar System
Warranty Registration
The Dotz TPar System carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 2
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 3
Dotz TPar System
Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required volt-
age for your unit.
•Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 23 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 4
Dotz TPar System
Set Up
Power Supply: The ADJ Dotz TPar System contains a automatic voltage switch, which will auto sense the voltage when it is plugged into
a power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere. Always
use the PowerCon cord that came with the unit.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Dotz TPar System can be controlled via DMX-512 protocol. The
Dotz TPar System has 5 DMX Channel Modes. The DMX address is set
on the rear panel of the Dotz TPar System. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data cable for data input
and data output (Figure 1). We recommend AccuCable DMX cables. If you are making your own
cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased
at almost all professional sound and lighting
stores). Your cables should be made with a male
and female XLR connector on either end of the
cable. Also remember that DMX cable must be
daisy chained and cannot be split.
Figure 1
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 5
POWER
POWER
Dotz TPar System
POWER
Set Up
Notice: Be sure
to DMX512
follow figures two and three when making your own
DMX+,DMX-,COMMON
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 OUT
3-PIN XLR
REMOTE
CONTROL
UND
INPUT
2
OUTPUT
3
DMX -
1
2
SOUND
XLR Female Socket
XLRINPUT
Male Socket
1 Ground
DMX +
3
2 Cold
2 Cold
1 Ground
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
INPUT
3
Figure 2
OUTPUT
1
2
XLR Pin Configuration
Pin 1 = Ground
Figure 3
3 Hot
1
2
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
CL:RGB
Flash00-99
Speed00-99
Flash00-99
FADE
Flash00-99
CHANGE
Speed00-99
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Speed00-99
Flash00-99
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Flash00-99
Speed & Flash adjustable
Speed & Flash adjustable
Speed & Flash adjustable
Speed & Flash adjustable
Speed & Flash adjustable
Seven color chase
Flash00-99
Speed & Flash adjustable
Seven color chase
Flash00-99
Speed & Flash adjustable
Seven color chase
Flash00-99
FLOW 7
Speed00-99
Speed & Flash adjustable
Seven color chase
FLOW 6
Speed00-99
Figure 4
Flash00-99
FLOW 5
Speed00-99
Speed & Flash adjustable
Seven color flow
Seven color chase
FLOW 4
Speed00-99
Seven color dreaming
Seven color chase
Flash00-99
FLOW 3
Speed00-99
Flash speed adjustable.
Seven color change
FLOW 2
Speed00-99
Red-Green-Blue-Yellow-Cyan-Purple-White
Seven color fade
FLOW 1
POWER
Special Note: Line Termination. When longer runs of cable are
3
Blackout,
STATIC COLOR
Speed00-99
Pin 3 = Data True (positive)
System Menu
Built-In Programs
DREAM
Termination reduces signal errors
and
avoids signal transmission problems
Speed00-99
Flash00-99
and interference. It is always
advisable
to connect a DMX terminal, (Resistance
METEOR
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Pin 2 = Data Compliment (negative)
3 Hot
Dotz TPar System
Speed & Flash adjustable
Seven color chase
Flash00-99
FLOW 8
Speed & Flash adjustable
Seven color chase
Speed00-99
Flash00-99
C1: RGB
C2:RGB
FLOW 9
Speed & Flash adjustable
Seven color chase
Speed00-99
Flash00-99
C1:RGB
C2:RGB
Speed & Flash adjustable
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 6
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 7
Dotz TPar System
System Menu
The LCD backlight will shut off after 30 seconds, to relight
the background, press the MODE button for 5 seconds.
DMX Mode - Set the DMX Address and DMX Channel
Mode -
1. Press the MENU button until “DMX Mode” and underneath “ADDR: XXX” and “CH:XX” is displayed, press ENTER.
2. “XXX” will now begin to flash, use the UP and DOWN buttons
to find your desired DMX address, then press ENTER.
3. “XX” will now begin to flash, use the UP and DOWN buttons to
find your desired DMX Channel mode, then press ENTER.
Slave Mode - This will let you set your unit as a slave in
a master/slave configuration.
1. Press the MENU button until “Slave Mode” is displayed. Your
unit will now follow the Master.
Dotz TPar System
System Menu
Auto Run -
1. Press the MENU button until “Auto Run” is displayed, and
“FQN:XX” will be displayed underneath. “XX” representing the
the number displayed.
2. Press ENTER and the number will begin to flash, use the UP
and DOWN buttons to adjust the amount of times you would like
the program to cycle before changing to the next program. Press
ENTER to confirm.
Built-In Programs - See the chart on page 7 to find
your desired program. Built-In Programs will not be displayed, one of the programs listed on page 7 will.
1. Press the MENU button until one of the Programs on page
7 is displayed. The displayed program depends on the last program you had set the unit to.
Sound Mode - In this mode the unit will run in sound
2. Press ENTER to move through the various adjustments of each
program, and use the UP and DOWN button to make adjustments.
1. Press the MENU button until “Sound Mode” is displayed.
Dim Curve - This setting will let you select your desired
active mode.
2. Press ENTER to adjust your sound sensitivity. When you press
ENTER the number next to “Sens” will begin to flash, use the
UP and DOWN buttons to adjust the sound sensitivity. Once you
found your desired sensitivity press ENTER to confirm.
3. When you press ENTER the number next to “FQN” will begin
to flash, use the UP and DOWN buttons to adjust the amount of
times you would like the program to cycle before changing to the
next program. Press ENTER to confirm.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 8
dimming curve.
1. Press the MENU button until “Dim Curve” is displayed, press
ENTER.
2. 1 of 5 dimming curve settings will be displayed: Standard,
Stage, TV, Architectural, or Theatre. Use the UP and DOWM buttons to select your desired dimming curve and press ENTER to
confirm.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 9
Dotz TPar System
System Menu
Pixel Flip - In this mode you adjust the unit so that the
LEDs in DMX mode will illuminate at your desired starting
point. The unit can start at either the left or the right.
1. Press the MENU button until “Pixel Flip” is displayed, press
ENTER.
2. Either “Off” or “On” will be displayed. “Off” the unit will illuminate left to right, and “On” the unit will illuminate right to left. Use
the UP and DOWN buttons to find your desired mode, and press
ENTER.
RF Active - This menu will let you activate the RF remote
control.
1. Press the MENU button until “RF Active” is displayed, press
ENTER.
2. Either “On” or “Off” will be displayed, use the UP or DOWN
buttons to activate (On) or deactivate (Off) the remote. Press
ENTER to confirm.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 10
Dotz TPar System
Universal DMX Control
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs. The Dotz TPar System
has 5 DMX channel modes; a 3 Channel Mode, 5 Channel Mode, 9
Channel Mode, 12 Channel Mode, & 18 Channel Mode. See pages
14-20 for the DMX channel modes and traits.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation® Show Designer™ or the Elation® DMX Operator.™
2. To run your fixture in DMX mode, follow directions on page 8 to set your DMX address and DMX Channel mode.
3. Plug in the fixture via the XLR connections to any standard DMX controller.
4. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
Dotz TPar System
Master-Slave Configuration
Master-Slave Operation: This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit, designate the unit as a “Master” unit following the instructions on page 10. Then set your desired operating mode.
3. On the slave units press the MODE button until “Slave Mode” is displayed.
4. The slave units will now follow the Master unit.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 11
Dotz TPar System
Foot Controller
The Foot Controller has 4 different functions. To control your fixture you must connect the foot controller using the provided cable.
Set the Dotz TPar System to its “Slave” setting. Connect one end
of the cable to the foot controller and the other end to the rear of
the Dotz TPar System bar. To activate the Foot Controller press any
pedal once. To deactivate the Foot Controller press the Blackout and
Program pedals at the same time.
BLACKOUT - Pressing this button will blackout the fixture. Press the
pedal for more then 3 seconds to activate Full On.
MODE - This pedal selects and activates the 3 different operating
modes. Press the pedal for more then 3 seconds to activate Full On.
• Press the MODE pedal and the Red LED lights up, you are Static Color mode. Use the UP and DOWN pedals to scroll through the 7 different colors.
• Press the MODE pedal and the Green LED lights up, you are in Sound Active mode. Adjust the sound sensitivity using the knob on the rear panel of the foot controller.
• Press the MODE pedal and the Yellow LED lights up, you are in the Built-In Programs mode. Use the UP and DOWN pedals to scroll through the 14 different programs. Refer to the chart on page 7 for the programs.
UP - This pedal works in conjunction with the MODE pedal, it lets
you scroll through the static colors and built-in programs. Press the
UP pedal for more then 3 seconds to activate connected light 1 (right
side of the bar). Press the pedal for more then 3 seconds to deactivate light 1.
DOWN - This pedal works in conjunction with the MODE pedal, it lets
you scroll through the static colors and built-in programs. Press the
DOWN pedal for more then 3 seconds to activate connected light 2
(left side of the bar). Press the pedal for more then 3 seconds to deactivate light 2.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 12
Dotz TPar System
Dotz RF Remote
The Dotz RF remote has many different functions and allows you to
control your Dotz TPar System from long distance. The remote can
control your system up to 25 meters. To use the remote you must first
activate the fixtures receiver, to activate the receiver please see the
instructions on page 11.
BLACKOUT - Pressing this button will blackout the fixture.
FADE - This button will activate the color fade program.
COLOR - This button will activate the static color mode. Use the “+”
and “-” buttons to scroll through the colors and find your desired
color.
PROGRAMS - This button will activate the built-in programs mode.
Use the “+” and “-” buttons to scroll through programs 2-14 to find
your desired program.
LIGHT 1 ON - This button will activate any light that is installed on the
top of the bar and connected to the first light connection (right side of
the bar).
LIGHT 1 OFF - This button will deactivate any light that is installed
on the top of the bar and connected to the first light connection (right
side of the bar).
LIGHT 2 ON - This button will activate any light that is installed on the
top of the bar and connected to the second light connection (left side
of the bar).
LIGHT 2 OFF - This button will deactivate any light that is installed on
the top of the bar and connected to the second light connection (left
side of the bar).
SOUND ACTIVE - This button activates sound active mode.
AUTO RUN - This button will run an automatic program. Use the “+”
and “-” buttons to adjust the speed of the auto run.
“+” and “-” - Use these buttons to adjust the speed of the Auto Run,
scroll through the built-in programs, and scroll through the static colors.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 13
Dotz TPar System
Channel
1
2
3
Value
0 - 255
0 - 255
0 - 255
Dotz TPar System
Channel
1
2
3
4
5
Value
0 - 255
0 - 255
0 - 255
0 - 127
128 - 255
0 - 127
128 - 255
3 Channel Mode
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
5 Channel Mode
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
LIGHT 1 (Installed on top of the bar)
OFF
ON
LIGHT 2 (Installed on top of the bar)
OFF
ON
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 14
Dotz TPar System
Channel
1
2
3
4
Value
0 - 255
0 - 255
0 - 255
0 - 15
16 - 23
24 - 31
32 - 39
40 - 47
48 - 55
56 - 63
64 - 71
72 - 79
80 - 87
88 - 95
96 - 103
104 - 111
112 - 119
120 - 127
128 - 135
136 - 143
144 - 151
152 - 159
160 - 167
168 - 175
176 - 183
184 - 191
192 - 199
200 - 207
208 - 215
216 - 223
9 Channel Mode
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
COLOR MACROS & PROGRAMS
NO FUNCTION
RED
GREEN
BLUE
RED & GREEN
GREEN & BLUE
RED & BLUE
RED, GREEN, & BLUE
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
COLOR FADE 1
COLOR SNAKE
COLOR FADE 2
COLOR CHANGE
COLOR FLOW 1
COLOR FLOW 2
COLOR FLOW 3
COLOR FLOW 4
COLOR FLOW 5
COLOR FLOW 6
COLOR FLOW 7
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 15
Dotz TPar System
Channel
4
Value
9 Channel Mode
Function
COLOR MACROS & PROGRAMS
224 - 231
COLOR FLOW 8
232 - 239
COLOR FLOW 9
240 - 255
SOUND ACTIVE
5
MASTER DIMMER/PROGRAM SPEED/
SOUND SENSITIVITY
0 - 255
MASTER DIMMER 0% - 100%
0 - 255
PROGRAM SPEED SLOW - FAST
0 - 255 SOUND SENSITIVITY LEAST - MOST
6
STROBING
0 - 255
SLOW - FAST
7
DIMMER CURVES
0 - 41
STANDARD
42 - 84
STAGE
85 - 127
TV
128 - 170
ARCHITECTURAL
171 - 213
THEATER
214 - 255 DEFAULT TO UNIT CURVE SETTING
8
LIGHT 1 (IF APPICABLE)
0 - 127
LIGHT 1 OFF
128 - 255
LIGHT 1 ON
9
LIGHT 2 (IF APPICABLE)
0 - 127
LIGHT 2 OFF
128 - 255
LIGHT 2 ON
When Channel 4 is being used between the values of 16-135,
Channel 5 will control the dimming.
Dotz TPar System
Channel
1
2
3
4
5
6
7
8
9
10
11
12
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
12 Channel Mode
Function
RED 1
0% - 100%
GREEN 1
0% - 100%
BLUE 1
0% - 100%
RED 2
0% - 100%
GREEN 2
0% - 100%
BLUE 2
0% - 100%
RED 3
0% - 100%
GREEN 3
0% - 100%
BLUE 3
0% - 100%
RED 4
0% - 100%
GREEN 4
0% - 100%
BLUE 4
0% - 100%
When Channel 4 is being used between the values of 136-239,
Channel 5 will control the speed of the programs.
When Channel 4 is being used between the values of 240-255,
Channel 5 will control sound sensitivity.
If extra lights are attached to the top of the bar, Channels 8 & 9
will control the lights.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 16
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 17
Dotz TPar System
Channel
1
2
3
4
5
6
7
8
9
10
11
12
13
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 15
16 - 23
24 - 31
32 - 39
40 - 47
48 - 55
56 - 63
64 - 71
72 - 79
18 Channel Mode
Function
RED 1
0% - 100%
GREEN 1
0% - 100%
BLUE 1
0% - 100%
RED 2
0% - 100%
GREEN 2
0% - 100%
BLUE 2
0% - 100%
RED 3
0% - 100%
GREEN 3
0% - 100%
BLUE 3
0% - 100%
RED 4
0% - 100%
GREEN 4
0% - 100%
BLUE 4
0% - 100%
COLOR MACROS & PROGRAMS
NO FUNCTION
RED
GREEN
BLUE
RED & GREEN
GREEN & BLUE
RED & BLUE
RED, GREEN, & BLUE
COLOR 1
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 18
Dotz TPar System
Channel
13
Value
80 - 87
88 - 95
96 - 103
104 - 111
112 - 119
120 - 127
128 - 135
136 - 143
144 - 151
152 - 159
160 - 167
168 - 175
176 - 183
184 - 191
192 - 199
200 - 207
208 - 215
216 - 223
216 - 223
224 - 231
232 - 239
240 - 255
14
0 - 255
0 - 255
0 - 255
15
0 - 255
16
0 - 41
42 - 84
85 - 127
18 Channel Mode
Function
COLOR MACROS & PROGRAMS
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
COLOR FADE 1
COLOR SNAKE
COLOR FADE 2
COLOR CHANGE
COLOR FLOW 1
COLOR FLOW 2
COLOR FLOW 3
COLOR FLOW 4
COLOR FLOW 5
COLOR FLOW 6
COLOR FLOW 7
COLOR FLOW 7
COLOR FLOW 8
COLOR FLOW 9
SOUND ACTIVE
MASTER DIMMER/PROGRAM SPEED/
SOUND SENSITIVITY
MASTER DIMMER 0% - 100%
PROGRAM SPEED SLOW - FAST
SOUND SENSITIVITY LEAST - MOST
STROBING
SLOW - FAST
DIMMER CURVES
STANDARD
STAGE
TV
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 19
Channel
16
Value
18 Channel Mode
Function
DIMMER CURVES
128 - 170
ARCHITECTURAL
171 - 213
THEATER
214 - 255 DEFAULT TO UNIT CURVE SETTING
17
LIGHT 1 (IF APPICABLE)
0 - 127
LIGHT 1 OFF
128 - 255
LIGHT 1 ON
18
LIGHT 2 (IF APPICABLE)
0 - 127
LIGHT 2 OFF
128 - 255
LIGHT 2 ON
When Channel 13 is being used between the values of 16-135,
Channel 14 will control the dimming.
When Channel 13 is being used between the values of 136-239,
Channel 14 will control the speed of the programs.
When Channel 13 is being used between the values of 240-255,
Channel 14 will control sound sensitivity.
If extra lights are attached to the top of the bar, Channels 17 &
18 will control the lights.
Dotz TPar System
Photometrics
Beam angle 25°
Field angle 35°
Intensity(LUX)
Red LEDs
Green LEDs
Blue LEDs
Full LEDs
2400
2760
4130
8650
749
904
1357
2680
360
427
646
1345
206
249
96
372
138
161
246
506
3
2
Beam opening(m)
Dotz TPar System
1
0
25
35
1
2
3
0
1
25° Diameter(m) 0.65
35° Diameter(m) 0.83
Dotz TPar System
2
1.08
1.45
3
4
1.83
2.10
1.97
2.70
5
2.41
3.35
Power Cord Daisy Chaining
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 7 fixtures maximum for 120V, and 14 fixtures maximum for 230V. After the maximum fixtures has been reached you
will need to use a new power outlet. They must be the same fixtures. DO NOT mix fixtures.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 20
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 21
Dotz TPar System
Alternate Lighting Installation
A special feature that this system has is that you are able to mount
two light effects on top of the “T” bar. You are then able to power
those lights by plugging the power cords directly into the bar. The
power sockets are located on the right side and left side. The middle
power socket is for power cord daisy chaining. Do not use the
middle power socket to power your added lights.
To add the lights onto the top is a simple process. Make sure your “T”
bar is set up on the stand correctly and is secure. Follow the instructions below.
1. Start by unscrewing the black knob that is attached to the bolt.
2. Attach the lighting effect to the bolt using the lighting effects connected bracket.
3. After you have set the bracket onto the bolt, screw the black knob
and secure the knob tightly. See the sample pictures below.
4. Plug the mounted lights into their respective power jacks.
Dotz TPar System
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry out
the fuse holder. Remove the bad fuse and replace with a new one. The
fuse holder has a built-in socket for a spare fuse be sure not to confuse
the spare fuse with active fuse.
Dotz TPar System
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use a soft cloth to wipe down the outside casing.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Dotz TPar System
Troubleshooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1.
Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
If problems are not resolved; Contact ADJ Products, LLC for service.
1-800-322-6337
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 22
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 23
Dotz TPar System
Warranty
Dotz TPar System
Notes
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested
repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC
will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
• Laser Products = 90-Day Limited Warranty
• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 24
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 25
Dotz TPar System
Specifications
SPECIFICATIONS:
Voltage: 100V~240V 50Hz/60Hz
LEDs:
Each Par contains a 30W COB TRI LED
Power Consumption:
144W Total (All LED’s @ Full)
Beam Angle:
90 Degrees
Includes 25 Degree Lens
Fuse:
3Amp (120V)
2Amp (240V)
Power Cord Daisy Chain:4 Fixtures Max. (120V)
9 Fixtures Max. (230V)
Weight: 35lbs./ 16Kgs.
Dimensions:
39.5” (L) x 12.75” (W) x 3.25” (H)
1000 x 320 x 82mm
Colors:
RGB Color Mixing
DMX Channels:
3 Channel Mode, 5 Channel Mode,
9 Channel Mode, 12 Channel Mode, & 18 Channel Mode
Working Position: Any safe working position
Warranty:
2 Year (730 days)
Auto Sensing Voltage: This fixture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 26
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Download PDF
Similar pages
Dotz T-Par System Details
Adj 141-00010 card reader
ULTRA BAR 12 ™
Datasheet for LED Light Bar with 6x3W RGB Tri LED's
ULTRA BAR 9 ™
Manual EN
FLAT PAR QA12XS™ #FLA496
Adj 120-00005 storage enclosure