data sheet tesiraforté® ai fixed audio dsp

DATA SHEET
TESIRAFORTÉ® AI
FIXED AUDIO DSP
The TesiraFORTÉ® AI is a fixed audio DSP with 12 analog inputs and 8 analog outputs and includes up
to 8 channels of configurable USB audio. USB audio allows TesiraFORTÉ to interface directly with USB
audio hosts, as well as to take full advantage of today’s most sophisticated conferencing solutions.
TesiraFORTÉ AI also provides extensive audio processing, including but not limited to: signal routing and
mixing, equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools; all
configured through the Tesira configuration software. TesiraFORTÉ AI is best-suited for small- to mediumsized rooms that require high-quality audio solutions using voice lift and mix-minus, such as conference
rooms or council chambers.
BENEFITS
• Includes default configuration file, allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• SpeechSense™ technology enhances speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 12 mic/line level inputs, 8 mic/line level outputs
• System configuration and control via Ethernet
• Gigabit Ethernet port
• Internal universal power supply
• Up to 8 channels of configurable USB audio
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• RS-232 serial port
• 4-pin GPIO
• 2-line OLED display with capacitive-touch navigation
• Rack mountable (1RU)
• CE marked, UL listed, and RoHS compliant
• Covered by Biamp Systems’ 5-year warranty
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Ethernet
connection for programming and control on a RJ-45 connector. The audio DSP shall have internal DSP processing.
The audio DSP shall include 4 channels of General Purpose Input and Output connection (GPIO) for sending or
receiving logic signals. The programming of the GPIO ports shall be software configurable. The audio DSP shall
include a RS-232 connection for control data transmission into or out of the audio DSP and such operation shall be
software programmable. The audio DSP shall include a Universal Serial Bus (USB) connection on a standard USB-B
type connector. The audio DSP shall be software configurable to stream up to 8 channels of digital USB Class 1 Audio
transmission either into or out of the audio DSP or simultaneous input and output. The audio DSP shall provide 12
balanced input connections for receiving of microphone or line level analog audio signals on screw-down, removable
connectors. The audio DSP shall provide 8 balanced output channels for the transmission of microphone or line level
analog audio signals on screw-down, removable connectors. Each individual channel shall have its own dedicated
connection. The audio DSP shall provide front panel OLED identification of device power, status, alarm, and activity
as well as system-wide alarm. The audio DSP shall be rack mountable (1RU) and feature software-configurable signal
processing, including but not limited to: signal routing and mixing, equalization, filtering, dynamics, and delay, as well as
control, monitoring, and diagnostic tools. The audio DSP shall be CE marked, UL listed, and shall be compliant with the
RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ AI.
TESIRAFORTÉ AI SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
Input Impedance (balanced):
> 108dB
8kΩ
Output Impedance (balanced):
Maximum Input:
207Ω
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ AI BACK PANEL
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESDS-307-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® AVB AI
FIXED AUDIO DSP
The TesiraFORTÉ® AVB AI is a fixed audio DSP with 12 analog inputs and 8 analog outputs and includes
up to 8 channels of configurable USB audio. USB audio allows TesiraFORTÉ to interface directly with
USB audio hosts, as well as to take full advantage of today’s most sophisticated conferencing solutions.
TesiraFORTÉ AVB AI utilizes Audio Video Bridging (AVB) for digital audio networking, and can be used
as a standalone device or combined with other TesiraFORTÉ devices and Tesira servers, expanders, and
controllers. TesiraFORTÉ AVB AI also provides extensive audio processing, including but not limited to:
signal routing and mixing, equalization, filtering, dynamics, and delay, as well as control, monitoring, and
diagnostic tools; all configured through the Tesira configuration software. TesiraFORTÉ AVB AI is
best-suited for small- to medium-sized rooms that require high-quality audio solutions using voice lift and
mix-minus, such as conference rooms or council chambers.
BENEFITS
• AVB allows audio networking via IEEE open standards protocol
• Includes default configuration file, allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• SpeechSense™ technology enhances speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 128 x 128 channels of AVB
• System configuration and control via Ethernet
• 12 mic/line level inputs, 8 mic/line level outputs
• Internal universal power supply
• Gigabit Ethernet port
• Fully compatible with Tesira AVB servers, endpoints,
expanders, and controllers
• Up to 8 channels of configurable USB audio
• 4-pin GPIO
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• 2-line OLED display with capacitive-touch navigation
• CE marked, UL listed, and RoHS compliant
• Rack mountable (1RU)
• Covered by Biamp Systems’ 5-year warranty
• RS-232 serial port
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Audio Video
Bridging (AVB) digital audio networking that shall allow up to 128 x 128 channels. The AVB networking connection shall
be implemented on a RJ-45 connector. The audio DSP shall support Ethernet connection for programming and control on
a RJ-45 connector. The audio DSP shall have internal DSP processing. The audio DSP shall include 4 channels of General
Purpose Input and Output connection (GPIO) for sending or receiving logic signals. The programming of the GPIO ports
shall be software configurable. The audio DSP shall include a RS-232 connection for control data transmission into or out
of the audio DSP and such operation shall be software programmable. The audio DSP shall include a Universal Serial Bus
(USB) connection on a standard USB-B type connector. The audio DSP shall be software configurable to stream up to 8
channels of digital USB Class 1 Audio transmission either into or out of the audio DSP or simultaneous input and output.
The audio DSP shall provide 12 balanced input connections for receiving of microphone or line level analog audio signals
on screw-down, removable connectors. The audio DSP shall provide 8 balanced output channels for the transmission
of microphone or line level analog audio signals on screw-down, removable connectors. Each individual channel shall
have its own dedicated connection. The audio DSP shall provide front panel OLED identification of device power, status,
alarm, and activity as well as system-wide alarm. The audio DSP shall be rack mountable (1RU) and feature softwareconfigurable signal processing, including but not limited to: signal routing and mixing, equalization, filtering, dynamics,
and delay, as well as control, monitoring, and diagnostic tools. The audio DSP shall control and proxy all Tesira expanderclass devices and Tesira control devices. The audio DSP shall be CE marked, UL listed, and shall be compliant with the
RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ AVB AI.
TESIRAFORTÉ AVB AI SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
> 108dB
Input Impedance (balanced):
8kΩ
Output Impedance (balanced):
207Ω
Maximum Input:
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ AVB AI BACK PANEL
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESDS-307-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® DAN AI
FIXED AUDIO DSP
The TesiraFORTÉ® DAN AI is a fixed audio DSP with 32 bi-directional channels of Dante™ digital audio,
12 analog inputs, 8 analog outputs, and includes up to 8 channels of configurable USB audio. USB audio
allows TesiraFORTÉ to interface directly with USB audio hosts, as well as to take full advantage of
today’s most sophisticated conferencing solutions. TesiraFORTÉ DAN AI provides extensive audio
processing, including but not limited to: signal routing and mixing, equalization, filtering, dynamics, and
delay; as well as control, monitoring, and diagnostic tools; all configured through the Tesira software.
TesiraFORTÉ DAN AI is best-suited for small- to medium-sized rooms that require high-quality audio
solutions using voice lift and mix-minus, such as conference rooms or council chambers.
BENEFITS
• Includes default configuration file, allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• SpeechSense™ technology enhances speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 32 x 32 channels of digital audio networking via the
Dante protocol
• Rack mountable (1RU)
• 12 mic/line level inputs, 8 mic/line level outputs
• Internal universal power supply
• 2 Gigabit Ethernet ports: Dante digital audio and Tesira
control
• Up to 8 channels of configurable USB audio
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• RS-232 serial port
• CE marked, UL listed, and RoHS compliant
• 4-pin GPIO
• Covered by Biamp Systems’ 5-year warranty
• System configuration and control via Ethernet
• 2-line OLED display with capacitive-touch navigation
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Dante™
digital audio networking that shall allow up to 32 x 32 channels. The Dante networking connection shall be implemented
on a RJ-45 connector. The audio DSP shall support Ethernet connection for programming and control on a RJ-45
connector. The audio DSP shall have internal DSP processing. The audio DSP shall include 4 channels of General Purpose
Input and Output connection (GPIO) for sending or receiving logic signals. The programming of the GPIO ports shall
be software configurable. The audio DSP shall include a RS-232 connection for control data transmission into or out of
the audio DSP and such operation shall be software programmable. The audio DSP shall include a Universal Serial Bus
(USB) connection on a standard USB-B type connector. The audio DSP shall be software configurable to stream up to 8
channels of digital USB Class 1 Audio transmission either into or out of the audio DSP or simultaneous input and output.
The audio DSP shall provide 12 balanced input connections for receiving of microphone or line level analog audio signals
on screw-down, removable connectors. The audio DSP shall provide 8 balanced output channels for the transmission
of microphone or line level analog audio signals on screw-down, removable connectors. Each individual channel shall
have its own dedicated connection. The audio DSP shall provide front panel OLED identification of device power, status,
alarm, and activity as well as system-wide alarm. The audio DSP shall be rack mountable (1RU) and feature softwareconfigurable signal processing, including but not limited to: signal routing and mixing, equalization, filtering, dynamics,
and delay, as well as control, monitoring, and diagnostic tools. The audio DSP shall be CE marked, UL listed, and shall be
compliant with the RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ DAN AI.
TESIRAFORTÉ DAN AI SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
> 108dB
Input Impedance (balanced):
8kΩ
Output Impedance (balanced):
207Ω
Maximum Input:
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ DAN AI BACK PANEL
851.0448.900 FINALS TESIRAFORTÉ DANTE AI
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESFDS-355-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® CI
FIXED AUDIO DSP
The TesiraFORTÉ® CI is a fixed audio DSP with 12 analog inputs and 8 analog outputs and includes
Acoustic Echo Cancellation (AEC) technology on all 12 inputs. It also includes up to 8 channels of
configurable USB audio. USB audio allows TesiraFORTÉ to interface directly with USB audio hosts, as
well as to take full advantage of today’s most sophisticated conferencing solutions. TesiraFORTÉ CI also
provides extensive audio processing, including but not limited to: AEC technology, signal routing and
mixing, equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools;
all configured through the Tesira configuration software. TesiraFORTÉ CI is best suited for small- to
medium-sized rooms that require high-quality audio solutions using AEC, voice lift, and mix-minus, such
as conference rooms or distance learning environments.
BENEFITS
• Includes default configuration file, allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• Acoustic Echo Cancellation (AEC) technology on all 12 inputs
• SpeechSense™ technology enhances speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 12 mic/line level inputs with AEC, 8 mic/line level outputs
• System configuration and control via Ethernet
• Gigabit Ethernet port
• Internal universal power supply
• Up to 8 channels of configurable USB audio
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• RS-232 serial port
• 4-pin GPIO
• 2-line OLED display with capacitive-touch navigation
• Rack mountable (1RU)
• CE marked, UL listed, and RoHS compliant
• Covered by Biamp Systems’ 5-year warranty
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Ethernet
connection for programming and control on a RJ-45 connector. The audio DSP shall have internal DSP processing. The
audio DSP shall include 4 channels of General Purpose Input and Output connection (GPIO) for sending or receiving
logic signals. The programming of the GPIO ports shall be software configurable. The audio DSP shall include a RS-232
connection for control data transmission into or out of the audio DSP and such operation shall be software programmable.
The audio DSP shall include a Universal Serial Bus (USB) connection on a standard USB-B type connector. The audio DSP
shall be software configurable to stream up to 8 channels of digital USB Class 1 Audio transmission either into or out of
the audio DSP or simultaneous input and output. The audio DSP shall provide 12 balanced input connections for receiving
of microphone or line level analog audio signals on screw-down, removable connectors. The input connections shall
include Acoustic Echo Cancellation (AEC) hardware and firmware, the parameters, routing and operation of which shall
be software programmable. The audio DSP shall provide 8 balanced output channels for the transmission of microphone
or line level analog audio signals on screw-down, removable connectors. Each individual channel shall have its own
dedicated connection. The audio DSP shall provide front panel OLED identification of device power, status, alarm, and
activity as well as system-wide alarm. The audio DSP shall be rack mountable (1RU) and feature software-configurable
signal processing, including but not limited to: signal routing and mixing, equalization, filtering, dynamics, and delay, as
well as control, monitoring, and diagnostic tools. The audio DSP shall be CE marked, UL listed, and shall be compliant with
the RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ CI.
TESIRAFORTÉ CI SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
Input Impedance (balanced):
> 108dB
8kΩ
Output Impedance (balanced):
Maximum Input:
207Ω
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ CI BACK PANEL
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESDS-307-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® AVB CI
FIXED AUDIO DSP
The TesiraFORTÉ® AVB CI is a fixed audio DSP with 12 analog inputs and 8 analog outputs and includes
Acoustic Echo Cancellation (AEC) technology on all 12 inputs. It also includes up to 8 channels of configurable
USB audio. USB audio allows TesiraFORTÉ to interface directly with USB audio hosts, as well as to take
full advantage of today’s most sophisticated conferencing solutions. TesiraFORTÉ AVB CI utilizes Audio
Video Bridging (AVB) for digital audio networking, and can be used as a standalone device or combined
with other TesiraFORTÉ devices and Tesira servers, expanders, and controllers. TesiraFORTÉ AVB CI also
provides extensive audio processing, including but not limited to: AEC technology, signal routing and mixing,
equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools; all configured
through the Tesira configuration software. TesiraFORTÉ AVB CI is best suited for small- to medium-sized
rooms that require high-quality audio solutions using AEC, voice lift, and mix-minus, such as conference rooms
or distance learning environments.
BENEFITS
• AVB allows audio networking via IEEE open standards protocol
• Includes default configuration file, allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• Acoustic Echo Cancellation (AEC) technology on all 12 inputs
• SpeechSense™ technology enhances speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 128 x 128 channels of AVB
• System configuration and control via Ethernet
• 12 mic/line level inputs with AEC, 8 mic/line level outputs
• Internal universal power supply
• Gigabit Ethernet port
• Fully compatible with Tesira AVB servers, endpoints,
expanders, and controllers
• Up to 8 channels of configurable USB audio
• 4-pin GPIO
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• 2-line OLED display with capacitive-touch navigation
• CE marked, UL listed, and RoHS compliant
• Rack mountable (1RU)
• Covered by Biamp Systems’ 5-year warranty
• RS-232 serial port
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Audio
Video Bridging (AVB) digital audio networking that shall allow up to 128 x 128 channels. The AVB networking
connection shall be implemented on a RJ-45 connector. The audio DSP shall support Ethernet connection for
programming and control on a RJ-45 connector. The audio DSP shall have internal DSP processing. The audio DSP shall
include 4 channels of General Purpose Input and Output connection (GPIO) for sending or receiving logic signals. The
programming of the GPIO ports shall be software configurable. The audio DSP shall include a RS-232 connection for
control data transmission into or out of the audio DSP and such operation shall be software programmable. The audio
DSP shall include a Universal Serial Bus (USB) connection on a standard USB-B type connector. The audio DSP shall
be software configurable to stream up to 8 channels of digital USB Class 1 Audio transmission either into or out of the
audio DSP or simultaneous input and output. The audio DSP shall provide 12 balanced input connections for receiving
of microphone or line level analog audio signals on screw-down, removable connectors. The input connections shall
include Acoustic Echo Cancellation (AEC) hardware and firmware, the parameters, routing and operation of which
shall be software programmable. The audio DSP shall provide 8 balanced output channels for the transmission of
microphone or line level analog audio signals on screw-down, removable connectors. Each individual channel shall have
its own dedicated connection. The audio DSP shall provide front panel OLED identification of device power, status,
alarm, and activity as well as system-wide alarm. The audio DSP shall be rack mountable (1RU) and feature softwareconfigurable signal processing, including but not limited to: signal routing and mixing, equalization, filtering, dynamics,
and delay, as well as control, monitoring, and diagnostic tools. The audio DSP shall control and proxy all Tesira
expander-class devices and Tesira control devices. The audio DSP shall be CE marked, UL listed, and shall be compliant
with the RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ AVB CI.
TESIRAFORTÉ AVB CI SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
> 108dB
Input Impedance (balanced):
8kΩ
Output Impedance (balanced):
207Ω
Maximum Input:
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ AVB CI BACK PANEL
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESDS-307-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® DAN CI
FIXED AUDIO DSP
The TesiraFORTÉ DAN CI is a fixed audio DSP with 32 bi-directional channels of Dante™ digital audio,
12 analog inputs with Acoustic Echo Cancellation (AEC), and 8 analog outputs. It also includes up to 8
channels of configurable USB audio. USB audio allows TesiraFORTÉ to interface directly with USB audio
hosts, as well as to take advantage of modern conferencing solutions. TesiraFORTÉ DAN CI provides
extensive audio processing, including but not limited to: signal routing and mixing, equalization, filtering,
dynamics, and delay; as well as control, monitoring, and diagnostic tools; all configured through the Tesira
configuration software. TesiraFORTÉ DAN CI is best-suited for small- to medium-sized rooms that require
high-quality audio solutions using AEC, voice lift, and mix-minus, such as conference rooms or distance
learning environments.
BENEFITS
• Includes default configuration file, allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• Acoustic Echo Cancellation (AEC) technology on all 12 inputs
• SpeechSense™ technology enhances speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 32 x 32 channels of digital audio networking via the
Dante protocol
• Rack mountable (1RU)
• 12 mic/line level inputs with AEC, 8 mic/line level outputs
• Internal universal power supply
• 2 Gigabit Ethernet ports: Dante digital audio and Tesira
control
• Up to 8 channels of configurable USB audio
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• RS-232 serial port
• CE marked, UL listed, and RoHS compliant
• 4-pin GPIO
• Covered by Biamp Systems’ 5-year warranty
• System configuration and control via Ethernet
• 2-line OLED display with capacitive-touch navigation
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Dante™
digital audio networking that shall allow up to 32 x 32 channels. The Dante networking connection shall be implemented
on a RJ-45 connector. The audio DSP shall support Ethernet connection for programming and control on a RJ-45
connector. The audio DSP shall have internal DSP processing. The audio DSP shall include 4 channels of General Purpose
Input and Output connection (GPIO) for sending or receiving logic signals. The programming of the GPIO ports shall
be software configurable. The audio DSP shall include a RS-232 connection for control data transmission into or out of
the audio DSP and such operation shall be software programmable. The audio DSP shall include a Universal Serial Bus
(USB) connection on a standard USB-B type connector. The audio DSP shall be software configurable to stream up to 8
channels of digital USB Class 1 Audio transmission either into or out of the audio DSP or simultaneous input and output.
The audio DSP shall provide 12 balanced input connections for receiving of microphone or line level analog audio signals
on screw-down, removable connectors. The input connections shall include Acoustic Echo Cancellation (AEC) hardware
and firmware, the parameters, routing and operation of which shall be software programmable. The audio DSP shall
provide 8 balanced output channels for the transmission of microphone or line level analog audio signals on screw-down,
removable connectors. Each individual channel shall have its own dedicated connection. The audio DSP shall provide
front panel OLED identification of device power, status, alarm, and activity as well as system-wide alarm. The audio DSP
shall be rack mountable (1RU) and feature software-configurable signal processing, including but not limited to: signal
routing and mixing, equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools. The
audio DSP shall be CE marked, UL listed, and shall be compliant with the RoHS directive. Warranty shall be five years.
The fixed audio DSP shall be TesiraFORTÉ DAN CI.
TESIRAFORTÉ DAN CI SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
> 108dB
Input Impedance (balanced):
8kΩ
Output Impedance (balanced):
207Ω
Maximum Input:
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ DAN CI BACK PANEL
851.0447.900 FINALS TESIRAFORTÉ DANTE CI
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESFDS-355-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® VT
FIXED AUDIO DSP
The TesiraFORTÉ® VT is a fixed audio DSP with 12 analog inputs and 8 analog outputs and includes Acoustic
Echo Cancellation (AEC) technology on all 12 inputs. It also includes up to 8 channels of configurable USB
audio, a 2-channel VoIP interface, and a standard FXO telephone interface. USB audio allows TesiraFORTÉ
to interface directly with USB audio hosts, as well as to take full advantage of today’s most sophisticated
conferencing solutions. TesiraFORTÉ VT provides extensive audio processing, including but not limited to:
AEC technology, signal routing and mixing, equalization, filtering, dynamics, and delay, as well as control,
monitoring, and diagnostic tools; all configured through the Tesira configuration software. TesiraFORTÉ VT
is best-suited for rooms that require high-quality audio solutions using VoIP, voice lift, mix-minus, and AEC,
such as conference rooms or distance learning environments.
BENEFITS
• Integrates VoIP, POTS, and USB audio in one product allowing integrators to choose the type of audio conferencing
that works best for their installation
• Includes default configuration file allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• SpeechSense™ technology to enhance speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 12 mic/line level inputs with AEC, 8 mic/line level outputs
• Internal universal power supply
• Gigabit Ethernet port
• SIP VoIP interface via a RJ-45 connector
• Up to 8 channels of configurable USB audio
• Standard FXO telephone interface via RJ-11 connector
• RS-232 serial port
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• 4-pin GPIO
• 2-line OLED display with capacitive-touch navigation
• Rack mountable (1RU)
• System configuration and control via Ethernet
• CE marked, UL listed, and RoHS compliant
• Covered by Biamp Systems’ 5-year warranty
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Ethernet connection for
programming and control on a RJ-45 connector. The audio DSP shall have internal DSP processing. The audio DSP shall include 4
channels of General Purpose Input and Output connection (GPIO) for sending or receiving logic signals. The programming of the GPIO
ports shall be software configurable. The audio DSP shall include a RS-232 connection for control data transmission into or out of the
audio DSP and such operation shall be software programmable. The audio DSP shall include a Universal Serial Bus (USB) connection
on a standard USB-B type connector. The audio DSP shall be software configurable to stream up to 8 channels of digital USB Class 1
Audio transmission either into or out of the audio DSP or simultaneous input and output. The audio DSP shall provide 4 balanced input
connections for receiving of microphone or line level analog audio signals on screw-down, removable connectors. The input connections
shall include Acoustic Echo Cancellation (AEC) hardware and firmware, the parameters, routing and operation of which shall be software
programmable. The audio DSP shall provide 4 balanced output channels for the transmission of microphone or line level analog audio
signals on screw-down, removable connectors. Each individual channel shall have its own dedicated connection. The audio DSP shall
integrate to Voice Over Internet Protocol (VoIP) systems on a RJ-45 connector for two lines of VoIP communication and shall support
Session Initiation Protocol (SIP) v2.0 or later. The audio DSP shall integrate to standard telephony communications on a RJ-11 connector
for a single line of telephone communication. The audio DSP shall provide front panel OLED identification of device power, status,
alarm, and activity as well as system-wide alarm. The audio DSP shall be rack mountable (1RU) and feature software-configurable
signal processing, including but not limited to: signal routing and mixing, equalization, filtering, dynamics, and delay, as well as control,
monitoring, and diagnostic tools. The audio DSP shall be CE marked, UL listed, and shall be compliant with the RoHS directive. Warranty
shall be five years. The fixed audio DSP shall be TesiraFORTÉ VT.
TESIRAFORTÉ VT SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
Input Impedance (balanced):
> 108dB
8kΩ
Output Impedance (balanced):
Maximum Input:
207Ω
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
FCC Part 68 (USA)
Industry Canada CS-03 (Canada)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ VT BACK PANEL
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESFDS-361-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® AVB VT
FIXED AUDIO DSP
The TesiraFORTÉ® AVB VT is a fixed audio DSP with 12 analog inputs and 8 analog outputs and includes
Acoustic Echo Cancellation (AEC) technology on all 12 inputs.It includes up to 8 channels of configurable USB
audio, a 2-channel VoIP interface, and a standard FXO telephone interface. USB audio allows TesiraFORTÉ
to interface directly with USB audio hosts, as well as to take full advantage of today’s most sophisticated
conferencing solutions. TesiraFORTÉ AVB VT utilizes Audio Video Bridging (AVB) for digital audio networking,
and can be used as standalone device or combined with other TesiraFORTÉ AVB devices and Tesira servers,
expanders, endpoints, and controllers. TesiraFORTÉ AVB VT also provides extensive audio processing,
including but not limited to: AEC technology, signal routing and mixing, equalization, filtering, dynamics, and
delay, as well as control, monitoring, and diagnostic tools; all configured through the Tesira configuration
software. TesiraFORTÉ AVB VT is best-suited for rooms that require high-quality audio solutions using VoIP,
voice lift, mix-minus, and AEC, such as conference rooms or distance learning environments.
BENEFITS
• Integrates VoIP, POTS, and USB audio in one product allowing integrators to choose the type of audio conferencing
that works best for their installation
• AVB allows audio networking via IEEE open standards protocol
• Includes default configuration file allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• SpeechSense™ technology to enhance speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 128 x 128 channels of AVB
• Internal universal power supply
• 12 mic/line level inputs with AEC, 8 mic/line level outputs
• SIP VoIP interface via a RJ-45 connector
• Gigabit Ethernet port
• Standard FXO telephone interface via RJ-11 connector
• Up to 8 channels of configurable USB audio
• Fully compatible with Tesira AVB servers, endpoints,
expanders, and controllers
• RS-232 serial port
• 2-line OLED display with capacitive-touch navigation
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• Rack mountable (1RU)
• CE marked, UL listed, and RoHS compliant
• System configuration and control via Ethernet
• Covered by Biamp Systems’ 5-year warranty
• 4-pin GPIO
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Audio Video Bridging
(AVB) digital audio networking that shall allow up to 128 x 128 channels. The AVB networking connection shall be implemented on a
RJ-45 connector. The audio DSP shall support Ethernet connection for programming and control on a RJ-45 connector. The audio DSP
shall have internal DSP processing. The audio DSP shall include 4 channels of General Purpose Input and Output connection (GPIO) for
sending or receiving logic signals. The programming of the GPIO ports shall be software configurable. The audio DSP shall include a
RS-232 connection for control data transmission into or out of the audio DSP and such operation shall be software programmable. The
audio DSP shall include a Universal Serial Bus (USB) connection on a standard USB-B type connector. The audio DSP shall be software
configurable to stream up to 8 channels of digital USB Class 1 Audio transmission either into or out of the audio DSP or simultaneous
input and output. The audio DSP shall provide 12 balanced input connections for receiving of microphone or line level analog audio
signals on screw-down, removable connectors. The input connections shall include Acoustic Echo Cancellation (AEC) hardware and
firmware, the parameters, routing and operation of which shall be software programmable. The audio DSP shall provide 8 balanced
output channels for the transmission of microphone or line level analog audio signals on screw-down, removable connectors. Each
individual channel shall have its own dedicated connection. The audio DSP shall integrate to Voice Over Internet Protocol (VoIP) systems
on a RJ-45 connector for two lines of VoIP communication and shall support Session Initiation Protocol (SIP) v2.0 or later. The audio
DSP shall integrate to standard telephony communications on a RJ-11 connector for a single line of telephone communication. The audio
DSP shall provide front panel OLED identification of device power, status, alarm, and activity as well as system-wide alarm. The audio
DSP shall be rack mountable (1RU) and feature software-configurable signal processing, including but not limited to: signal routing and
mixing, equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools. The audio DSP shall control and
proxy all Tesira expander-class devices and Tesira control devices. The audio DSP shall be CE marked, UL listed, and shall be compliant
with the RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ AVB VT.
TESIRAFORTÉ AVB VT SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
> 108dB
Input Impedance (balanced):
8kΩ
Output Impedance (balanced):
207Ω
Maximum Input:
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
FCC Part 68 (USA)
Industry Canada CS-03 (Canada)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ AVB VT BACK PANEL
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESFDS-361-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® DAN VT
FIXED AUDIO DSP
The TesiraFORTÉ® DAN VT is a fixed audio DSP with 32 bi-directional channels of Dante™ digital audio, 12
analog inputs with Acoustic Echo Cancellation (AEC) technology, and 8 analog outputs. It also includes up to
8 channels of configurable USB audio, a 2-channel VoIP interface, and a standard FXO telephone interface.
USB audio allows TesiraFORTÉ to interface directly with USB audio hosts, as well as to take full advantage
of today’s most sophisticated conferencing solutions. TesiraFORTÉ DAN VT also provides extensive audio
processing, including but not limited to: AEC technology, signal routing and mixing, equalization, filtering,
dynamics, and delay, as well as control, monitoring, and diagnostic tools; all configured through the Tesira
configuration software. TesiraFORTÉ DAN VT is best-suited for rooms that require high-quality audio solutions
using VoIP, voice lift, mix-minus, and AEC, such as conference rooms or distance learning environments.
BENEFITS
• Integrates VoIP, POTS, and USB audio in one product allowing integrators to choose the type of audio conferencing
that works best for their installation
• Includes default configuration file allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• SpeechSense™ technology to enhance speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 32 x 32 channels of digital audio networking via the
Dante protocol
• System configuration and control via Ethernet
• 12 mic/line level inputs with AEC, 8 mic/line level outputs
• SIP VoIP interface via a RJ-45 connector
• Gigabit Ethernet port
• Standard FXO telephone interface via RJ-11 connector
• Up to 8 channels of configurable USB audio
• 4-pin GPIO
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• 2-line OLED display with capacitive-touch navigation
• CE marked, UL listed, and RoHS compliant
• Rack mountable (1RU)
• Covered by Biamp Systems’ 5-year warranty
• RS-232 serial port
• Internal universal power supply
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Dante™ digital audio
networking that shall allow up to 32 x 32 channels. The Dante networking connection shall be implemented on a RJ-45 connector. The
audio DSP shall support Ethernet connection for programming and control on a RJ-45 connector. The audio DSP shall have internal DSP
processing. The audio DSP shall include 4 channels of General Purpose Input and Output connection (GPIO) for sending or receiving
logic signals. The programming of the GPIO ports shall be software configurable. The audio DSP shall include a RS-232 connection
for control data transmission into or out of the audio DSP and such operation shall be software programmable. The audio DSP shall
include a Universal Serial Bus (USB) connection on a standard USB-B type connector. The audio DSP shall be software configurable
to stream up to 8 channels of digital USB Class 1 Audio transmission either into or out of the audio DSP or simultaneous input and
output. The audio DSP shall provide 12 balanced input connections for receiving of microphone or line level analog audio signals on
screw-down, removable connectors. The input connections shall include Acoustic Echo Cancellation (AEC) hardware and firmware, the
parameters, routing and operation of which shall be software programmable. The audio DSP shall provide 8 balanced output channels
for the transmission of microphone or line level analog audio signals on screw-down, removable connectors. Each individual channel
shall have its own dedicated connection. The audio DSP shall integrate to Voice Over Internet Protocol (VoIP) systems on a RJ-45
connector for two lines of VoIP communication and shall support Session Initiation Protocol (SIP) v2.0 or later. The audio DSP shall
integrate to standard telephony communications on a RJ-11 connector for a single line of telephone communication. The audio DSP shall
provide front panel OLED identification of device power, status, alarm, and activity as well as system-wide alarm. The audio DSP shall
be rack mountable (1RU) and feature software-configurable signal processing, including but not limited to: signal routing and mixing,
equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools. The audio DSP shall be CE marked, UL
listed, and shall be compliant with the RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ DAN VT.
TESIRAFORTÉ DAN VT SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
> 108dB
Input Impedance (balanced):
8kΩ
Output Impedance (balanced):
207Ω
Maximum Input:
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
FCC Part 68 (USA)
Industry Canada CS-03 (Canada)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
< -85dB
< -75dB
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ DAN VT BACK PANEL
VoIP
BIAMP SYSTEMS
12
Telephone Line
11
10
9
8
7
+ -
+ -
+ -
Made in USA, US and Imported Parts
www.biamp.com
inputs
6
5
4
3
2
1
+ -
+ -
+ -
+ -
+ -
+ -
TESIRAFORTÉ DAN VT
Control
100 - 240V~
50/60Hz 0.5 - 0.21A
10
US: 6RMBR00BTES01, Complies with FCC Part 68 IC: 3184A-TES01
+ -
+ -
+ -
Logic I/O
RS-232
+5V 4 3 2 1
outputs
542.0421.90B ARTWORK CHASSIS TESIRAFORTÉ DANTE VT
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESFDS-361-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® AVB VT4
FIXED AUDIO DSP
The TesiraFORTÉ® AVB VT4 is a fixed audio DSP with 4 analog inputs, 4 channels of Acoustic Echo
Cancellation (AEC) technology, and 4 analog outputs. It also includes up to 8 channels of configurable USB
audio, a 2-channel VoIP interface and a standard FXO telephone interface. USB audio allows TesiraFORTÉ
to interface directly with USB audio hosts, as well as to take full advantage of today’s most sophisticated
conferencing solutions. TesiraFORTÉ AVB VT4 utilizes Audio Video Bridging (AVB) for digital audio
networking, and can be used as a standalone device or combined with other TesiraFORTÉ AVB devices and
Tesira servers, expanders, and controllers. TesiraFORTÉ AVB VT4 also provides extensive audio processing,
including but not limited to: AEC technology, signal routing and mixing, equalization, filtering, dynamics, and
delay; as well as control, monitoring, and diagnostic tools; all configured through the Tesira configuration
software. TesiraFORTÉ AVB VT4 is best-suited for smaller rooms that require high-quality audio solutions
using VoIP, voice lift, mix-minus, and AEC, such as conference rooms or distance learning environments.
BENEFITS
• Integrates VoIP, POTS, and USB audio in one product allowing integrators to choose the type of audio conferencing
that works best for their installation
• AVB allows audio networking via IEEE open standards protocol
• Includes default configuration file allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• SpeechSense™ technology to enhance speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 128 x 128 channels of AVB
• Internal universal power supply
• 4 mic/line level inputs with AEC, 4 mic/line level outputs
• SIP VoIP interface via a RJ-45 connector
• Gigabit Ethernet port
• Standard FXO telephone interface via RJ-11 connector
• Up to 8 channels of configurable USB audio
• Fully compatible with Tesira AVB servers, endpoints,
expanders, and controllers
• RS-232 serial port
• 2-line OLED display with capacitive-touch navigation
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• Rack mountable (1RU)
• CE marked, UL listed, and RoHS compliant
• System configuration and control via Ethernet
• Covered by Biamp Systems’ 5-year warranty
• 4-pin GPIO
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Audio Video Bridging
(AVB) digital audio networking that shall allow up to 128 x 128 channels. The AVB networking connection shall be implemented on a
RJ-45 connector. The audio DSP shall support Ethernet connection for programming and control on a RJ-45 connector. The audio DSP
shall have internal DSP processing. The audio DSP shall include 4 channels of General Purpose Input and Output connection (GPIO) for
sending or receiving logic signals. The programming of the GPIO ports shall be software configurable. The audio DSP shall include a
RS-232 connection for control data transmission into or out of the audio DSP and such operation shall be software programmable. The
audio DSP shall include a Universal Serial Bus (USB) connection on a standard USB-B type connector. The audio DSP shall be software
configurable to stream up to 8 channels of digital USB Class 1 Audio transmission either into or out of the audio DSP or simultaneous
input and output. The audio DSP shall provide 4 balanced input connections for receiving of microphone or line level analog audio
signals on screw-down, removable connectors. The input connections shall include Acoustic Echo Cancellation (AEC) hardware and
firmware, the parameters, routing and operation of which shall be software programmable. The audio DSP shall provide 4 balanced
output channels for the transmission of microphone or line level analog audio signals on screw-down, removable connectors. Each
individual channel shall have its own dedicated connection. The audio DSP shall integrate to Voice Over Internet Protocol (VoIP) systems
on a RJ-45 connector for two lines of VoIP communication and shall support Session Initiation Protocol (SIP) v2.0 or later. The audio
DSP shall integrate to standard telephony communications on a RJ-11 connector for a single line of telephone communication. The audio
DSP shall provide front panel OLED identification of device power, status, alarm, and activity as well as system-wide alarm. The audio
DSP shall be rack mountable (1RU) and feature software-configurable signal processing, including but not limited to: signal routing and
mixing, equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools. The audio DSP shall control and
proxy all Tesira expander-class devices and Tesira control devices. The audio DSP shall be CE marked, UL listed, and shall be compliant
with the RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ AVB VT4.
TESIRAFORTÉ AVB VT4 SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
> 108dB
Input Impedance (balanced):
8kΩ
Output Impedance (balanced):
207Ω
Maximum Input:
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
FCC Part 68 (USA)
Industry Canada CS-03 (Canada)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ AVB VT4 BACK PANEL
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESFDS-360-1710-EN-R1
DATA SHEET
TESIRAFORTÉ® DAN VT4
FIXED AUDIO DSP
The TesiraFORTÉ® DAN VT4 is a fixed audio DSP with 32 bi-directional channels of Dante™ digital audio,
4 analog inputs, 4 channels of Acoustic Echo Cancellation (AEC) technology, and 4 analog outputs. It
also includes up to 8 channels of configurable USB audio, a 2-channel VoIP interface and a standard FXO
telephone interface. USB audio allows TesiraFORTÉ to interface directly with USB audio hosts, as well as
to take full advantage of today’s most sophisticated conferencing solutions. TesiraFORTÉ DAN VT4 also
provides extensive audio processing, including but not limited to: AEC technology, signal routing and mixing,
equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools; all configured
through the Tesira configuration software. TesiraFORTÉ DAN VT4 is best-suited for smaller rooms that require
high-quality audio solutions using VoIP, voice lift, mix-minus, and AEC, such as conference rooms or distance
learning environments.
BENEFITS
• Integrates VoIP, POTS, and USB audio in one product allowing integrators to choose the type of audio conferencing
that works best for their installation
• Includes default configuration file allowing for plug-and-play usage
• Highly scalable and cost-effective solution that can grow over time with the needs of the customer
• SpeechSense™ technology to enhance speech processing
• Integrates directly with soft codecs and other USB audio hosts
FEATURES
• 32 x 32 channels of digital audio networking via the
Dante protocol
• System configuration and control via Ethernet
• 4 mic/line level inputs with AEC, 4 mic/line level outputs
• SIP VoIP interface via a RJ-45 connector
• Gigabit Ethernet port
• Standard FXO telephone interface via RJ-11 connector
• Up to 8 channels of configurable USB audio
• 4-pin GPIO
• Signal processing via intuitive software allows
configuration and control for signal routing, mixing,
equalization, filtering, delay and much more
• 2-line OLED display with capacitive-touch navigation
• CE marked, UL listed, and RoHS compliant
• Rack mountable (1RU)
• Covered by Biamp Systems’ 5-year warranty
• RS-232 serial port
• Internal universal power supply
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
ARCHITECTS & ENGINEERS SPECIFICATION
The fixed audio DSP shall be designed exclusively for use with Tesira® systems. The audio DSP shall support Dante™ digital audio
networking that shall allow up to 32 x 32 channels. The Dante networking connection shall be implemented on a RJ-45 connector. The
audio DSP shall support Ethernet connection for programming and control on a RJ-45 connector. The audio DSP shall have internal DSP
processing. The audio DSP shall include 4 channels of General Purpose Input and Output connection (GPIO) for sending or receiving
logic signals. The programming of the GPIO ports shall be software configurable. The audio DSP shall include a RS-232 connection
for control data transmission into or out of the audio DSP and such operation shall be software programmable. The audio DSP shall
include a Universal Serial Bus (USB) connection on a standard USB-B type connector. The audio DSP shall be software configurable
to stream up to 8 channels of digital USB Class 1 Audio transmission either into or out of the audio DSP or simultaneous input and
output. The audio DSP shall provide 4 balanced input connections for receiving of microphone or line level analog audio signals on
screw-down, removable connectors. The input connections shall include Acoustic Echo Cancellation (AEC) hardware and firmware, the
parameters, routing and operation of which shall be software programmable. The audio DSP shall provide 4 balanced output channels
for the transmission of microphone or line level analog audio signals on screw-down, removable connectors. Each individual channel
shall have its own dedicated connection. The audio DSP shall integrate to Voice Over Internet Protocol (VoIP) systems on a RJ-45
connector for two lines of VoIP communication and shall support Session Initiation Protocol (SIP) v2.0 or later. The audio DSP shall
integrate to standard telephony communications on a RJ-11 connector for a single line of telephone communication. The audio DSP shall
provide front panel OLED identification of device power, status, alarm, and activity as well as system-wide alarm. The audio DSP shall
be rack mountable (1RU) and feature software-configurable signal processing, including but not limited to: signal routing and mixing,
equalization, filtering, dynamics, and delay, as well as control, monitoring, and diagnostic tools. The audio DSP shall be CE marked, UL
listed, and shall be compliant with the RoHS directive. Warranty shall be five years. The fixed audio DSP shall be TesiraFORTÉ DAN VT4.
TESIRAFORTÉ DAN VT4 SPECIFICATIONS
Frequency Response:
20Hz to 20kHz, +4dBu output: Phantom Power: +0.25 dB/-0.5 dB
THD+N (22Hz to 22kHz):
0dB gain, +4dBu input:
54dB gain, -50dBu input:
< 0.006%
< 0.040%
EIN (no weighting, 22Hz to 22kHz):
< -125dBu
Dynamic Range (in presence of signal)
22Hz to 22kHz, 0dB gain:
> 108dB
Input Impedance (balanced):
8kΩ
Output Impedance (balanced):
207Ω
Maximum Input:
+24dBu
Maximum Output (selectable):
+24dBu, +18dBu, +12dBu,
+6dBu, 0dBu, -31dBu
Input Gain Range (6dB steps):
0-66dB
Overall Dimensions:
Height:
Width:
Depth:
Weight:
Environment:
Ambient Operating
Temperature Range:
Humidity:
Altitude:
+48VDC (7mA/input)
Crosstalk, channel to channel, 1 kHz:
0dB gain, +4dBu input: 54dB gain, -50dBu input: < -85dB
< -75dB
Sampling Rate:
48kHz
A/D - D/A Converters:
24-bit
Power Consumption:
100-240VAC 50/60Hz:
< 35W
USB:
Bit Depth:
Number of Channels:
Sample Rate:
Compliance:
1.75 inches (44 mm)
19.0 inches (483 mm)
10.5 inches (267 mm)
8 lbs (3.63 kg)
16- or 24-bit
up to 8
48kHz
FCC Part 15B (USA)
FCC Part 68 (USA)
Industry Canada CS-03 (Canada)
CE marked (Europe)
UL und C-UL listed (USA and Canada)
RCM (Australia)
RoHS Directive (Europe)
32-104° F (0–40° C)
0–98%, non-condensing
0-6,600 feet (0–2000 Meters) MSL
TESIRAFORTÉ DAN VT4 BACK PANEL
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
T: +1 503.641.7287
W: www.biamp.com
TESFDS-360-1710-EN-R1