8 CHANNEL/
16 CHANNEL DVR
User Manual
SRD-840/1640
Your local installer: www.eaglesecuritysolutions.co.uk
8 Channel/
16 Channel DVR
User Manual
Copyright
©2012 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or
changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided.
Use of this document and the subsequent results shall be entirely on the user's own responsibility. Samsung Techwin reserves the right to change the
contents of this document without prior notice.
 Design and specifications are subject to change without prior notice.
 The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
overview
IMPORTANT SAFETY INSTRUCTIONS
 OVERVIEW
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. if the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from
tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
English _3
overview
BEFORE START
This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection
to other equipment, menu setup, etc.
You have to keep in mind the following notices :
• SAMSUNG retains the copyright on this manual.
• This manual cannot be copied without SAMSUNG’s prior written approval.
• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of
instructions mentioned in this manual.
• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be
removed from the unit.
• Before installing an additional HDD or connecting an external storage device (USB memory or USB HDD) to this
DVR, check the compatibility. Consult your provider for the compatibility list.
Warning
❖ Battery
It is essential that when changing the battery in the unit, the replacement battery must be of the same type
otherwise there may be a possibility of an explosion.
The following are the specifications of the battery you are using now.
• Normal voltage : 3V
CALIFORNIA USA ONLY
• Normal capacity : 170mAh
This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA.
• Continuous standard load : 0.2mA
“Perchlorate Material - special handling may apply,
• Operating temperature : -20°C ~ +85°C
See www.dtsc.ca.gov/hazardouswaste/perchlorate.”
(-4°F ~ +185°F)
Caution
• Connect the power cord into a grounded outlet.
• The Mains plug is used as a disconnect device and shall stay readily operable at any time.
• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the
Instructions.
❖ System Shutdown
Turning off the power while the product is in operation, or undertaking improper actions may cause damage
or malfunction to the hard drive or the product.
Disconnecting the power cable for power off.
For a safe power disconnection, select <OK> in the system shutdown dialog before unplugging the power cord.
You may want to install a UPS system for safe operation in order to prevent damage caused by an
unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)
❖ Operating Temperature
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).
This product may not work properly if you run right after a long period of storage at a temperature below the
guaranteed one.
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand
at room temperature for a period.
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).
Likewise, the hard drive may not work at a temperature below the guaranteed one.
4_ overview
CONTENTS
OVERVIEW
3
12
LIVE
17
USING THE DVR
28
Important Safety Instructions
Before Start
Contents
Features
Part Names and Functions (Front)
Part Names and Functions (Rear)
Remote Control
12
12
13
13
13
14
14
15
Installation
Checking the installation environment
Connecting the Video, Audio, and Monitor
Connecting the USB
Connecting POS Device
Connecting the Alarm Input/Output
Connecting the RS-485 Device
Connecting the Network
17
19
23
25
26
26
26
27
Getting Started
Live Screen Configuration
Live Mode
Spot Out
Zoom
Audio ON/OFF
Freeze
Event Monitoring
28
38
46
49
52
53
61
System Setup
Setting the Device
Setting the Recording
Setting the Event
Backup
Network Configuration
Controlling a PTZ device
English _5
 OVERVIEW
CONNECTING WITH OTHER DEVICE
3
4
5
7
9
10
11
overview
SEARCH & PLAY
64
WEB VIEWER
69
BACKUP VIEWER
64
67
Search
Playback
69
70
71
77
81
92
93
Introducing Web Viewer
Connecting Web Viewer
Using Live Viewer
Using Search Viewer
Viewer Setup
About
Mobile Viewer
94
SEC Backup Viewer
96
99
101
104
107
Product Specification
Product Overview
Default Setting
Troubleshooting
Open Source License Report on the Product
94
APPENDIX
96
6_ overview
FEATURES
This DVR enables you to compress 8 or 16 channels of camera video sources into H.264 format, and to compress
4 channels of sound sources simultaneously before saving and recording on the HDD.
These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video
and audio data.
• Provides a convenient User Interface
• 8/16 CH Composite Input Connectors
 OVERVIEW
• Supports CIF(S)/2CIF(M)/4CIF(L) recording formats
• With the network specific codec, network transfer enabled regardless of the recording conditions
• Display of HDD information and status by using HDD SMART
• Hard Disk overwrite function
• Mass storage hard disk backup through high-speed USB 2.0
• Simultaneous Record and Playback of 8/16-channel video data
• Various Search Modes (Time, Event, Backup, Pos, Motion Detection)
• Various Recording Modes (Manual, Event, Scheduled Recording)
• Alarm Interface
• Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer
English _7
overview
Standards Approvals
M
 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Package Contents
Please unwrap the product, and place the product on a flat place or in the place to be installed.
Check if the main unit and all the following accessories are included in the product package.
DVR
Adapter
Power Cable
Mouse
Remote Control / Battery (AAA x 2)
User Manual
Quick Guide (optional)
Network Viewer Software /
User Manual CD
Terminal Block (SRD-840)
Terminal Block (SRD-1640)
8_ overview
PART NAMES AND FUNCTIONS (FRONT)
b c
Part Names
 OVERVIEW
Functions
USB Port
Connects the USB devices.
b
Remote Control
Receiver
Input the remote control signal.
POWER : Displays the power ON/OFF status.
c
LED Indicator
ALARM : Lights on when an event occurs.
REC : Lights on when recording is in progress.
English _9
overview
PART NAMES AND FUNCTIONS (REAR)
SRD-840
CH1
CH2
CH3
CH4
b
DC 12 V
1
AUDIO IN
c
VIDEO IN
2
3
4
5
6
7
SPOT
8
1
ALARM
OUT
VIDEO IN
AUDIO OUT
VGA OUT
COM COM
2
1 2 3 4 5 6 7 8 G
RS485
ALARM IN
SERIAL
9
5
10
6
11
7
12
8
13
14
15
16
VIDEO OUT
CONSOLE
NETWORK
SRD-1640
CH1
CH2
CH3
CH4
b
2
3
4
5
6
7
SPOT
8
1
VIDEO IN
AUDIO OUT
M
1 2 3 4 5 6 7 8 G 9 10 11 12 13 14
RS485
ALARM IN
15 16 G
SERIAL
9
10
11
12
13
14
15
16
VIDEO OUT
Part Names
b
c
VGA OUT
COM COM
2
ALARM
OUT
DC 12 V
1
AUDIO IN
c
VIDEO IN
CONSOLE
NETWORK
Functions
AUDIO IN
Input ports (RCA jack) for the audio signal.
VIDEO IN
Input port for the composite video signal.
SPOT
BNC type of output port for the Spot signal.
ALARM IN
1~8, G : Alarm Input port.
1~16, G : Alarm Input port.
ALARM OUT
1~2, COM : Alarm Output port.
RS-485
Used to establish RS-485 communications.
VGA OUT
Output port for VGA video signal.
DC 12V
DVR power input port.
NETWORK
NETWORK connector port.
SERIAL
Serial port for connecting to a POS device.
VIDEO OUT
BNC type of output port for the composite video signal.
AUDIO OUT
Output port (RCA jack) for the audio signal.
 [CONSOLE] is designed for the service repair purpose only.
 If you want to change the default output to VGA mode when the live screen is displayed with the beep after the
system booting, press the remote control buttons in sequence: [FREEZE]  [VIEW]  [RETURN ( )] 
[FREEZE]  [VIEW]  [RETURN ( )]. The DVR will switch to VGA mode with the beep after rebooting.
 For more information about monitor output, refer to “Video Output”. (Page 44)
10_ overview
REMOTE CONTROL
SEARCH
Displays the search menu.
BACKUP
Displays the Backup Menu.
MODE
Changes the screen mode.
POWER
DVR
Activates the DVR function.
Displays the Exit pop up screen.
ID
Skip Backward (by unit time),
Step Backward, Step Forward,
Skip Forward (by unit time)
Sets the ID of the system.
Select 2 digits from 0 ~ 9 while pressing the ID Key.
Move Frame
While paused, moves to the previous/next frame.
FR, STOP, PLAY/PAUSE, FF
T/W
Zooms in or out.
PTZ
Displays or ends PTZ.
SCROLL ,.
Moves the menu scroll.
MENU
Goes to the system menu screen.
RETURN
Returns to the previous screen.
Up/Down/Left/Right(▲▼◄ ►)/ENTER
Moves the cursor up/down/left/right, and runs the
Select Menu.
FREEZE
Freezes the screen temporarily.
ZOOM
AUDIO
Turns Audio on/off.
ALARM
Cancels the Alarm.
Runs the digital zoom (x2) function.
REC
Starts or ends the live recording.
VIEW
Runs the View function in the PTZ mode.
REC LOCK
Selects the recording lock function.
PRESET
Displays the Preset Setup.
Using the Numeric buttons
CHANNEL 1–9
Press each button between 1 to 9.
CHANNEL 10
Press the [+10] button first, then press the 0 button again within 3 seconds.
CHANNEL 11–16
Press the [+10] button first, then press any number between 1 to 6 within 3 seconds.
Changing the Remote Control ID
1. Press the ID button of the remote control and check the ID displayed on the DVR screen.
The factory default ID of the remote control is 00.
2. Enter 2 digits of your selection in order, while pressing the system [ID] button.
3. When ID input is done, press the system [ID] button again to check the setting.
M
 If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.
Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 42)
English _11
 OVERVIEW
NUMBER [0~+10]
Used as the numeric input keys, or displays a single
channel.
connecting with other device
INSTALLATION
Please take note of the followings before using this product.
•
•
•
•
•
•
•
•
Do not use the product outdoor.
Do not spill water or liquid in the connection part of the product.
Do not impose the system to excessive shock or force.
Do not pull out the power plug forcefully.
Do not disassemble the product on your own.
Do not exceed the rated input/output range.
Use a certified power cord only.
For the product with an input ground, use a grounded power plug.
CHECKING THE INSTALLATION ENVIRONMENT
Samsung Digital Video Recorder (“DVR” hereinafter) is a
state-of-art security device, and contains mass storage hard
disk(s) and critical circuits inside.
Temperature
Unit: ºC
One Year: 24HR X 365 DAY =8,760 HR
When the temperature rises inside the product, the product
may breakdown and the product life be shortened.
Life (Unit: HOURS)
12_ connecting with other device
CH1
CH2
CH3
CH4
VIDEO IN
CONNECTING THE VIDEO, AUDIO, AND MONITOR
AUDIO
IN
O IN
AUDIO
OUT
VIDEO IN
1
AUDI
2
3
4
5
9
6
 CONNECTING WITH OTHER DEVICE
10
7
11
8
12
1
SPOT
13
14
COM
2
COM
ALA
RM
OUT
RS485
1 2
3 4
5 6
7 8
G
9 10
11
ALAR
M IN
15
12 13
14
15 16
G
16
VIDEO
OUT
VGA
OUT
DC 12
V
SERIA
L
CONS
OLE
NETW
ORK
M
 The following figures are based on Model SRD-1640.
CONNECTING THE USB
1. By factory default, a USB port is provided for external connection.
2. You can connect a USB HDD, USB memory or mouse to the USB port.
3. If a USB HDD is connected to the system, recognition and settings are available in “Menu > Setting the Device >
Storage Device”. (Page 40)
4. This product supports hot-plugging, which connects/removes the USB device during the system operation.
J
 If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.
CONNECTING POS DEVICE
1. You can connect a POS device to the RS-232C port on the product’s rear side when you connect it directly with
a RS-232C cable.
2. Connection setup for the RS-232C port is available in “Menu > Device > POS Devices”, press the
<POS Device Setup> button and set <Baudrate, Parity, Data, Stop bit and Transfer Type>. (Page 42)
English _13
connecting with other device
CONNECTING THE ALARM INPUT/OUTPUT
Connecting the alarm input signal
DC 12 V
1
COM COM
2
ALARM
OUT
Connect one strand of the sensor signal line to one of 8/16 strands
of the alarm input port, and connect the other strand to the [G] port.
1 2 3 4 5 6 7 8 G
RS485
ALARM IN
SERIAL
DEO OUT
CO
CONSOLE
NETWORK
Connecting the alarm output signal
Connect one strand of the sensor signal line to the alarm output
port and connect the other to the [COM] port.
1
COM COM
2
ALARM
OUT
1 2 3 4 5 6 7 8 G
RS485
ALARM IN
• ALARM IN : 5mA sink
< SRD-840 >
• ALARM OUT : 24V DC 1A, 125VAC/0.5A
DC 12 V
1
VGA OUT
COM COM
2
ALARM
OUT
1 2 3 4 5 6 7 8 G 9 10 11 12 13 14
RS485
ALARM IN
15 16 G
SERIAL
VIDEO OUT
1
COM COM
2
ALARM
OUT
CONSOLE
NETWORK
1 2 3 4 5 6 7 8 G 9 10 11 12 13 14
RS485
ALARM IN
15 16 G
< SRD-1640 >
CONNECTING THE RS-485 DEVICE
Connect the rear [RS-485 +, –] port to the PTZ camera or system
keyboard.
M
 You can connect and control the PTZ camera which supports the
1
COM COM
2
ALARM
OUT
RS-485 communication.
 Check if the RS-485 device is compatible with the product first.
1 2 3 4 5 6 7 8 G
RS485
ALARM IN
< SRD-840 >
 Pay attention not to change the polarity (+/-) of the RS-485 device
when connecting it.
 Depending on camera’s type, connection polarity can be different.
For further information, refer to the respective PTZ Camera’s
documentation.
1
COM COM
2
ALARM
OUT
1 2 3 4 5 6 7 8 G 9 10 11 12 13 14
RS485
ALARM IN
< SRD-1640 >
14_ connecting with other device
15 16 G
CONNECTING THE NETWORK
Connecting to Network through Ethernet (10/100BaseT)
VIDEO IN
CH1
CH2
CH3
CH4
AUD
IO IN
IN
IO OUT
2
3
 CONNECTING WITH OTHER DEVICE
AUD
VIDEO IN
1
AUDIO
4
5
9
6
10
7
11
8
12
SPO
13
1
T
COM
2
COM
ALAR
M
OUT
14
RS485
1 2
3 4
5 6
7 8
G
9 10
11
ALA
RM
15
12 13
IN
14
15 16
G
16
VIDEO
OUT
VGA
OUT
DC 12V
SERIAL
CON
SOLE
NETWORK
NETWO
RK
RJ-45 Ethernet Cable
(Direct Cable)
Back B
one
Hub/Switcher
Hub/Switcher
Windows
Network Viewer
Connecting to the Network using the router
VIDEO IN
CH1
CH2
CH3
CH4
AUD
IO IN
IN
AUD
IO OUT
VIDEO IN
1
AUDIO
2
3
4
5
9
6
10
7
11
8
12
SPO
13
1
T
14
COM
2
COM
ALAR
M
OUT
RS485
1 2
3 4
5 6
7 8
G
9 10
11
ALA
RM
15
IN
12 13
14
15 16
G
16
VIDEO
OUT
VGA
OUT
DC 12V
SERIAL
CON
xDSL or Cable Modem
SOLE
NETWO
RK
Broadband Router
NETWORK
xDSL or Cable Modem
External Remote PC
DDNS Server
(Data Center)
English _15
connecting with other device
Connecting to Internet through ADSL
VIDEO IN
CH1
CH2
CH3
CH4
AUD
IO IN
IN
AUD
IO OUT
VIDEO IN
1
AUDIO
2
3
4
5
9
6
10
7
11
8
12
SPO
13
1
T
14
COM
2
COM
ALAR
M
OUT
RS485
1 2
3 4
5 6
7 8
G
9 10
11
ALA
RM
15
IN
12 13
14
15 16
G
16
VIDEO
OUT
VGA
OUT
DC 12V
SERIAL
CON
SOLE
INTERNET
RJ-45 Ethernet Cable
(Direct Cable)
Phone(A
DSL) Lin
e
Hub/Switcher
Windows
Network Viewer
16_ connecting with other device
NETWO
RK
ADSL MODEM
live
GETTING STARTED
Starting the system
M
 LIVE
1. Connect the power cable of the DVR to the wall outlet.
 It takes about 10 seconds to display the start screen after
booting.
2. You will see the initialization screen.
The initialization process will last about 1 minute.
If a new HDD is installed, the initialization process may
take longer.
REC
3. The live screen appears with a beep.
2012-01-01 01:10:25
2012-01-01
01:10:25
Shutting Down the System
You can shut down the system only if you have logged into the DVR.
You require permission to shut down the system if you are not logged in as admin.
1. Right-click to display the context menu and select
<Shutdown>, or press the [POWER] button on the
remote control.
2. The “Shutdown” confirmation window appears.
3. Use the arrow keys on the remote control to move to
<OK> and press the [ENTER] button or click <OK>.
The system will shut down.
2012-01-01 01:10:25
Shutdown
Are you sure to shutdown?
OK
Cancel
4. Disconnecting the power cable for power off and
reconnecting the power cable to restart.
M
 For the permission management, refer to “Permission Management > Setting Permissions”. (Page 33)
English _17
live
Login
To access a DVR or restricted menu, you should have logged in to the DVR.
1. In live mode, right-click any area of the screen.
You will see the context sensitive menu as in the right
figure.
Scene Mode 
2012-01-01 01:10:25
Spot Out

Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Login
2. Click <Login>.
The login dialog appears.
You can also see the login dialog to access a desired
menu by pressing the [MENU] button on the remote
control.
 The login dialog will also appear if you press a menu button on
the remote control of the DVR when the corresponding menu
requires logging in.
2012-01-01 01:10:25
Login
 ID
admin
 Password
OK
Cancel
 After logged in, press [RETURN] on the remote control to display
the logout dialog.
 By default, initial ID and password are set to “admin”, and “4321”.
J
 The default password can be exposed to a hacking thread so it is recommended to change the password after
M
 For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 33)
installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
Locking All Buttons
This will restrict access to all buttons available in the DVR.
1. In Live mode, press the remote control buttons in the order
of [STOP (@)]  [FREEZE]  [STOP (@)]  [FREEZE] 
[MENU].
2. In the lock condition, press any button to display a dialog
where you are prompted to enter the password for
unlocking the buttons.
The button lock will be released if you enter the admin
password.
18_ live
2012-01-01 01:10:25
Key Lock Password
 ID
admin
 Password
OK
Cancel
LIVE SCREEN CONFIGURATION
Icons on the Live Screen
You can check the status or operation of the DVR with the icons on the live screen.
2012-01-01 00:00:01
 LIVE
CAM 01
Name
b
Description
Current Date, Time
Displays the current time and date.
Login Information
When you are logged in, the “LOG ON” icon will be displayed.
Displayed if the zoom function is activated.
Freezes the screen temporarily.
c
Screen Mode
Displayed in Auto Sequence mode where all channels are switched at the specific
time interval.
This icon is displayed if a user with restricted access to the Record button tries to
make manual recording.
 Only the user with the applicable permission can release (stop) the recording.
Displayed if the HDD is full and the DVR has an insufficient space to record.
Displayed if no HDD is installed or the existing HDD should be replaced.
System Operation
Displayed if the HDD needs a technical examination.
Displayed while the backup is in process or if the backup data is played.
Displayed if the firmware can be updated via the network.
Video Input Status
Camera Name/ Channel
Displayed if no input is entered in the condition that the camera is set to <ON>.
Nothing will be displayed on the screen if the camera is set to <OFF>.
Displays the camera name and the changed channel, if any.
Displays the resolution of the recording screen. (Page 47)
Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.
Camera Operation
Displays AUDIO ON/MUTE.
Not displayed in video mode if deactivated.
If the sensor is set to <ON>, the input signal will be displayed on the screen of the
connected channel.
Displayed if a motion detected in the condition that the motion detection is set to
<ON>.
Displays the current record mode from Record/Event/Schedule.
English _19
live
Error Information
• If the internal HDD is not connected, the “NO HDD”(
) message will appear; if there occurs a problem,
) message in the top left corner. In this case, make sure you contact the
you will see the “HDD FAIL”(
service center for assistance as this may cause a failure of recording, playback or backup.
M
 If you see the NO HDD, HDD FAIL icons on the screen, contact the service center for more details.
Live Screen Menu
In addition to the buttons the remote control, you can access a desired menu by right-clicking the mouse any
area in live mode.
The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/logout,
screen split mode and DVR operation mode.
M
 Menu items of Search, Record, Backup, Shutdown and PTZ can be deactivated, depending on the user permission.
Scene Mode 
2012-01-01 01:10:25
Scene Mode
2012-01-01 01:10:25

Spot Out
Spot Out
Audio Off
PTZ Control
Freeze
Zoom In
Stop Alarm
Audio Off
Record
Freeze
Play
Stop Alarm
Search
Record
Backup
Play
Main Menu
Search
Shutdown
Backup
Hide Launcher
Main Menu
Logout
Shutdown


Hide Launcher
Logout
< Single Mode Menu >
< Split Mode Menu >
Split Mode Menu
The context sensitive menu in split mode differs, depending on the login/logout status.
13
20_ live
12
11
10
9
8
7
6
5
4
3
2
1
Scene Mode 
Spot Out

Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
2012-01-01 01:10:25
Menu
b
c
m
Scene Mode
Refer to “Live Mode”. (Page 23)
Spot Out
Refer to “Spot Out”. (Page 25)
Audio On/Off
Refer to “Audio ON/OFF”. (Page 26)
Freeze
Refer to “Freeze”. (Page 26)
Stop Alarm
Stop the alarm output, deactivate the event icon and release the auto sequencing.
Refer to “Event Monitoring”. (Page 27)
Record/Stop
Starts/stops the standard recording.
Play
Refer to “Search & Play > Play”. (Page 67)
Search
Refer to “Search & Play > Search”. (Page 64)
Backup
Refer to “Using the DVR > Setting the Backup”. (Page 52)
Main Menu
Accesses the main menu. Refer to the Using the DVR section. (Page 28)
Shutdown
Turns down the DVR.
Show/Hide Launcher
Shows or hides the launcher. Refer to “View the Launcher Menu”. (Page 22)
Login/Logout
You can log in or out.
Single Mode Menu
The single mode menu is available only in Single Mode.
The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode.
1
Spot Out
3
2
2012-01-01 01:10:25
Full Screen

PTZ Control
Zoom In
Audio On
Freeze
Stop Alarm
Record
Play
Shutdown
Hide Launcher
Logout
Menu
Description
Full Screen
Select and click a desired channel in Split mode to switch to the full screen of the selected
channel.
b
PTZ Control
Accesses the PTZ Control menu.
The PTZ menu will be active on Live screen if you select a single channel. (Page 61)
c
Zoom In
Enlarges the selected image. (Page 26)
English _21
 LIVE
Description
live
View the Launcher Menu
The Launcher menu appears on the bottom of the live screen.
1. In Live mode, right-click to display the context menu and
select <Show Launcher>.
2012-01-01 01:10:25
2. Move the cursor to the bottom and click a desired item in
the Launcher menu.
M
 If no input is entered for 10 seconds, the menu will disappear.
 The Launcher menu can be accessed only by using the
mouse.
2012-01-01
01:10:25
 SRD-840 does not support the 16-split screen mode.
2012-01-01
01:10:25
2012-01-01
01:10:25
PTZ
b
Alarm
Freeze
c Menu
Description
Date/Time
Displays the current time and date.
The indication of AM/PM is displayed if you set 12 hours for the time format in “System >
Date/Time/Language > Time”. (Page 28)
b
Screen Mode
Press this button to switch the screen mode in sequence.
The current screen mode will be displayed in white.
Menu Expansion Button
Click to display the hidden menu to the right.
Audio
Turns ON/MUTE the sound of the selected channel.
Zoom
Enlarges the selected area. This is available only in Single Live mode.
PTZ
Runs the PTZ Control launcher.
The PTZ control launcher will be active on the Live screen after you select a single channel.
Alarm
Stops the alarm if it's activated.
Freeze
Freezes the Live screen temporarily.
Play
Enters Play mode if a file to play exist, and if not, enters Search mode.
Record
Start/End recording the Live screen.
c
22_ live
LIVE MODE
SRD-1640 display Live images from 16 channels in a total of 8 layout of split screens.
Switching the screen mode
M
 SRD-840 do not support the 16-split screen mode.
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
CH1
CH3
CH2
CH1
CH4
CH5
CH6
CH7
CH8
CH9
16-split mode
CH1
CH2
CH2
CH1
CH3
CH2
CH2
CH3
CH6
CH3
CH4
CH8
CH1
CH8
CH10
CH11
CH4
CH4
CH4
9-split mode
CH3
4-split mode
CH5
CH6
6-split mode
CH5
CH7
CH19
CH2
CH5
CH6
CH7
8-split mode
CH12
CH13
CH1
CH1
13-split mode
PIP
Auto Sequence
Switching the split mode
SRD-1640 display 16 Live images in the sequence of Single, 4-split and 9-split modes.
Auto Sequence
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
Single mode
M
CH2
CH1
16
CH2
CH1
CH3
CH1
CH3
CH1
CH3
1
13-16
9-12
5-8
1-4
CH1
CH4
CH2
CH3
CH4
CH4
4-split mode
CH2
CH3
CH4
CH2
CH4
CH7
CH4
CH7
CH2
CH5
CH8
CH5
CH8
CH3
CH6
CH9
CH6
CH9
10-16
1-9
9-split mode
 In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be
conducted at the set interval. (Page 38)
 In a split mode, If you have set <Multi CH SEQ Time> in “Setting the Device > Monitor”, Auto Sequence will be
conducted at the set interval. (Page 44)
English _23
 LIVE
To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in
the context menu.
Press the [MODE] button on the remote control to switch the screen mode in the order suggested in the
launcher menu.
live
Manual Switching
Press the left/right button on the remote control, or click the arrow <◄/►> key to move to the next split mode.
• If pressing the right [►] button in 9-split mode :
9-split (CH 1~9) mode  9-split (CH 10~16) mode  Auto Sequence
CH1
CH4
CH2
CH3
CH5
CH10
CH6
CH11
CH13
CH14
CH12
CH1
CH15
CH1
CH4
CH4
CH7
CH8
CH9
CH2
CH2
CH5
CH5
CH7
CH16
CH7
CH3
CH3
CH6
CH6
CH8
CH8
CH9
CH9
10-16
1-9
• If pressing the right [►] button in 4-split mode :
Channel (CH 1~4)  Channel (CH 5~8)  Channel (CH 9~12)  Channel (CH 13~16)  Auto Sequence
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
CH1
CH2
CH1
CH3
CH1
CH3
CH1
CH2
CH3
CH3
CH4
CH4
CH4
CH4
CH2
CH2
13-16
9-12
5-8
1-4
Channel Setting
You can display the channel in a desired area of a split screen.
1. Place the cursor over the camera name of each channel to display the <▼> key to the right on the screen.
2. Click a camera name to display a channel list where you can select a different channel.
3. Select a desired channel and click it.
The current channel will be switched to the selected one.
Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also
change the channel position.
 Ex : if switching CH 1 to CH 7
24_ live
CH7
CH2
CH3
CH4
CH5
CH6
CH1
CH8
CH12
CH9
CH10
CH11
CH12
CH16
CH13
CH14
CH15
CH16
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH13
CH14
CH15
Switching to Single Mode
When in split mode, select and double-click a desired channel to switch to its Single mode.
Press the number corresponding to a desired channel the remote control to switch to its Single mode.
Refer to “Remote Control > Using the numeric buttons”. (Page 11)
 Ex : If you click number 3 channel button or press the number 3 on the remote control.
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
 LIVE
CH1
CH3
SPOT OUT
The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out
port.
Selecting a Spot Out mode
If an event occurs such as sensor, motion or alarm from the Spot Out port in connection with a monitor, you
can select a output screen mode.
1. In Live mode, right-click any area on the screen.
The Live menu appears.
2. Click <Spot Out>.
Supports the Spot output in Single screen with Auto
Sequence mode.
 If the monitor is connected to the Spot port, the event that
occurred from the selected channel will be output on the
monitor.
For the Spot Out port of a model, refer to “Part Names and
Functions (Rear)”. (Page 10)
Scene Mode 
Spot Out

Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
2012-01-01 01:10:25
Auto Sequence
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
lti h
l Li
<M
Multichannel
Live M
Menu >
English _25
live
ZOOM
This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to
enlarge it twice.
1. Select <Zoom In> in the right-click menu.
Press the [ZOOM] button on the remote control, or simply click <
box appears.
> in the launcher menu. The zoom
2. Use the direction keys, or drag and drop to specify an area to enlarge.
3. Press the [ENTER] button, or double-click the selected area to enlarge it twice.
 In the enlarged image, use the direction buttons (◄ ►) on the remote controlto move the enlarged area.
4. Press the [ZOOM] button on the remote control, or simply click <
the zoom.
> in the launcher menu to release
2012-01-01 01:10:25
AUDIO ON/OFF
In Live mode, you can selectively turn on/off the sound from each channel.
AUDIO ON/OFF in Single mode
Click the audio icon (
M
) on the screen, or press the [AUDIO] button on the remote control to turn it on/off.
 Only the channel where <AUDIO> is set to <ON> in “Device > Camera” displays the audio icon (
that you can use to turn the sound on/off.
FREEZE
This is available only in Live mode, this pauses playing the Live image temporarily.
1. Press the [FREEZE] button the remote control, or click <
The playback of the image is stopped temporarily.
2. Press the [FREEZE] button again, or click <
This will release the freeze.
26_ live
Freeze
>.
Freeze
> in the launcher menu.
) in Live mode
EVENT MONITORING
This will display the channel in sync with a specific event (Sensor/Motion/Video Loss) if it occurs.
In “Monitor > Event Display”, set the event monitoring to ON/OFF and specify the event display time. (Page 44)
• If multiple events occur simultaneously, the screen will switch to a split mode.
- 2~4 events : 4-split mode
- 5~9 events : 9-split mode
- 10~16 events : 16-split mode
Event occurrence
5 seconds
Stop alarm
CH1
 Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first
event occurred in CH 1.
Event occurrence
4 seconds
9 seconds
Stop alarm
CH1
CH2
CH1
M
 Press the [ALARM] button to reset the alarm settings and to release the event mode.
 If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will
be performed.
 This will also apply to the Spot Out monitor.
J
 If such as motion events occur consecutively, and you stop the event alarm but another event occurs, it may not
work properly to switch the split mode or manipulate the menus.
English _27
 LIVE
• If the second event occurs within the set time of <Event Display>, the first event will last until the second
one is terminated. (Page 44)
 Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.
using the DVR
You can setup the system properties, devices, and options for recording, event,
backup and network.
SYSTEM SETUP
You can setup Date/Time/Language, Permission, System Properties and Log.
Date/Time/Language
You can check and setup the current Date/Time and time related properties, as well as the language used for
the interface on the screen.
Setting the Date/Time/Language
Set the Date/Time/Language
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control.
2012-01-01 01:10:25
 If not logged in, it prompts with login window.
Refer to “Login”. (Page 18)
2012-01-01
01:10:25
2. Use the left/right buttons (◄ ►) to select the <System>.
System property setup menu is selected.
3. Use the up/down buttons () to select <Date/Time/
Language> and press the [ENTER] button.
Logout
System
4. Select <Date/Time/Language>.
A dialog to setup Date, Time and Language.
Date/Time/Language
Permission Management
System Management
5. Use direction buttons (◄ ►) to select an item to set
and make your changes.
• Date : Sets the date that will appear on the screen.
You can select the date format.
• Time : Sets the time and its format that will appear on the
screen.
Select either one from <24 Hours, 12 Hours (AM/PM)>.
• Time Zone : Sets the time zone of your area based on the
Greenwich Mean Time (GMT).
 GMT (Greenwich Mean Time) is standard World Time and the basis
of world time zone.
Log Information
Date/Time/Language
Date/Time/Language
 Date
Holiday
2012-01-01
YYYY-MM-DD
 Time
08:14:24
24 Hours
 Time Zone
GMT
 Time Sync.
 DST
 Language
Setup
Dec First (Sun) 0
Dec First (Sun) 0
English
OK
Cancel
• Time Sync. : You can set the DVR’s current time
synchronized to a selected <Time Server> regularly if you select to use <Time Server>.
In this case, <Date/Time/Language> setup does not allow time adjustment.
28_ using the DVR
Return
- Time Server : Enter an IP or URL address of the time
Date/Time/Language
server.
Date/Time/Language
Holiday
- Last Sync Time : Displays the most recent
Time Synchronization Setup
synchronization time from the selected time server.
- Activate as Server : Set to <Use> to allow the DVR to act
as a Time Server for other DVRs.
• DST : Set up Daylight Saving Time with its period to make
the time earlier than the GMT of its time zone by 1 hour
during the set period.
• Language : Select your language. Sets the language for the
interface.
English, French, German, Spanish, Italian, Chinese, Russian, Korean, Polish, Japanese, Dutch, Portuguese,
Turkish, Czech, Danish, Swedish, Thai, Romanian, Serbian, Croatian, Hungarian and Greek are available.
 Date
2012 -01-01
YYYY-MM-DD
Use
 Synchronization
08:14:24
24 Hours
 Time
203.248.240.103
 Time Server
GMT+08:00
 Time Zone
Fail
 Last Sync Time
Setup
Not Used
 Time Sync.
Use
 Activate as Server
Dec First (Sun) 0H
Dec First (Sun) 0H
 DST
 Language
OK
Cancel
OK
Cancel
English
M
 You can also use numeric buttons on the remote control to enter values for Date, Time and other numeric fields.
Setting Holiday
You can set specific dates to Holidays according to your preferences.
Holidays are applied to <Recording Schedule> and <Alarm Schedule> too.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Date/Time/Language> window to select <Date/Time/Language>, and
press the [ENTER] button.
2. Select <Holiday>.
Date/Time/Language
A calendar for Holiday setup appears.
Holiday
Date/Time/Language
3. Use the left/right <
> buttons to select year or month,
2012
Jan
and press the [ENTER] button.
Sun Mon Tue
Wed Thu
Fri
Sat
1
2
3
4
 Ex : Select January 9th and check on <1/9> only to make every
January 9th a holiday. Check both on <1/9> and <Jan 2nd
Mon> to make every January 9th and 2nd Monday of January
holidays.
6
7
9
10
11
12
13
14
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Sat
7
OK
4. Use direction buttons (◄ ►) to select a desired date,
and press the [ENTER] button.
You will see the “Setting Holiday” screen.
5
8
15
Cancel
Date/Time/Language
Holiday
Date/Time/Language
2012
Jan
Setting
Sun Holiday
Mon Tue
1
2
8
9
15
16
3
1/9
10
Wed
4
Thu
5
Fri
6
11
12
13
14
19
20
21
27
28
Jan 2nd Mon
17
22
23
OK
24
29
30
31
18
25
Cancel
26
5. When the Holiday setup is done, press <OK>.
OK
Cancel
Using the Calendar
Using the mouse may help make setup easier.
{ Select year and month.
Select the left/right <
> key on the left/right side of year/month and press [ENTER] button to
adjust by 1 year/month.
| Use direction buttons to select a date and press [ENTER] button.
 A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and Event
Search.
English _29
 USING THE DVR
6. When the Date/Time/Language setup is done, press <OK>.
using the DVR
Permission Management
You can set permissions of each user over the DVR's specific function and settings.
Setting the Administrator
You can set and change Administrator’s ID and password.
The administrator can use and set all menu items and functions.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Permission Management>, and press
[ENTER] button.
Permission Management
Admin
Group
 ID
2. Select <Admin>.
A dialog for Admin ID and Password input appears.
User
Setup
admin
 New Password
************
 Confirm P/W
************
3. Use direction buttons (◄ ►) to move to a desired
item, and set the ID and password.
M
 By default, initial ID and password are set to “admin”, and
OK
Cancel
“4321”.
 The default password can be exposed to a hacking thread so it iis recommended
d d tto change
h
th
the passwordd after
ft
installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
4. When the administrator setup is done, press <OK>.
Using Virtual Keyboard
{ For alphanumeric inputs, the virtual keyboard window
appears.
| Use direction buttons (◄ ►) to move to a desired
character, and press the [ENTER] button.
} In the upper text input box of the virtual keyboard, there
displays a list of candidate words containing the selected
character.
`
1
2
3
4
5
6
7
8
9
0
-
=

q
w
e
r
t
y
u
i
o
p
[
]
\
Del
a
s
d
f
g
h
j
k
l
;
‘
Caps Lock
z
x
c
v
b
n
m
,
.
/
Space
OK
Shift
Ctrl
Cancel
~ Select a word from the list, or use the keyboard to enter the
whole word.
 If there are many of candidate words, use < , > buttons to move between them forward and backward.
 Select <OK>.
Entered word is applied.
 For upper case letters, use <Caps Lock> button.





For special characters, use <Shift> button.
Using the virtual keyboard is the same to a normal keyboard use in your region.
You can type the ID with alphanumeric characters only.
For the password, use alphabets and special characters excluding < \ > and <“>.
You can use number buttons on the remote control.
30_ using the DVR
Setting the Group
You can create user groups and setup permissions for those user groups.
You can register a user for each group in <User>.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Permission Management>, and press
[ENTER] button.
Group
Admin
User
 Group
Add
Setup
Delete
Rename
 Group Authority
Live View
Setup
Search
Setup
Backup
Setup
 USING THE DVR
2. Select <Group>.
A window for <Add>, <Delete>, <Rename>, and
<Group Authority> setup appears.
Permission Management
Setup
Menu
Bi-directional audio
3. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
Record Lock
PTZ
Remote Alarm Out
OK
• Add, Delete, Rename : You can add, delete, rename a
group or modify the permissions given to the group.
The virtual keyboard appears when <Add> or <Rename> was selected.
Shutdown
Cancel
- Add : When you first run the DVR with the admin account, only the admin account exists. Add has already
been deactivated. Select to display the virtual keyboard. Enter a group name. You can add up to 10
groups.
- Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts
belonging to that group.
- Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard.
 For entering a group name, refer to “Using Virtual Keyboard”. (Page 30)
• Group Authority : Sets permissions to access menu items of each group.
Users of a group can access checked functions.
4. When the group setup is done, press <OK>.
To set the group authority
You can set the permissions of the group users to access the menu according to the channel.
1. Select a menu to which the group permission is assigned.
The menu where the group permission is assigned will be
displayed in the Live menu when a group user logs in.
• Live View : You can set the permission to access the Live
screen according to the channel.
• Search : You can set the permission to access the Search
menu according to the channel.
Permission Management
Group
Admin
 Group
Add
 Group Authority
Channel
Live View
• Bi-directional audio : You will be given permission to use
two-way audio features.
• Record Lock, PTZ, Remote Alarm Out, Shutdown : Select
an item so that the item will be added to the permissions.
2. Select <OK>.
Select and assign a group user so that the user can
access the specified menu.
Setup
Delete
Rename
Setup
Setup
All
Setup
Search
1
Backup
5
Menu
9
2
Setup
Setup
13
Bi-directional audio
Record Lock
3
4
6
7
8
10
11
12
15
16
14
PTZ
OK
• Backup : You can set the permission to access the Backup
menu according to the channel.
• Menu : You can set menus accessible with a specific
permission.
Group users can access the permitted menus only.
Select a menu to display the Menu Permission screen
User
ABC
Remote Alarm Out
Cancel
OK
Shutdown
Cancel
Permission Management
Menu Permission Group
Admin
User
Setup
All
Group
 System
ABC
Device
Record
Add
Event
Delete
Backup
Rename
Network
Group Authority
Date/Time/Language
Setup
Live View
Date/Time/Language
Holiday
Setup
Search
System Management
Setup
Backup
System Information
Settings
Setup
Menu
Log Information
Record Lock
PTZ
Remote Alarm Out
Shutdown
System Log
Event Log
Backup Log
OK
OK
Cancel
Cancel
English _31
using the DVR
To restrict the user permissions
If the admin restricts all permissions of an added group, the users belonging to that group can access only
the default minimum menus and can change the user’s own password only.
1. Start the DVR.
If all permissions are restricted, only the Login dialog
should appear.
2. Log in with a registered user ID.
Login
 ID
abc
 Password
OK
3. Right-click any area on the screen.
If all permissions are restricted, only the accessible context
menus should appear.
Cancel
2012-01-01 01:10:25
Scene Mode

Audio Off
Freeze
Stop Alarm
User Menu
Hide Launcher
Logout
To change the user password
If you log in with a user account that is restricted to access the menu, you can change your own password
only.
1. Log in with your account.
2. Select <User Menu>.
The Permission Management setup screen appears.
3. Select <Permission Management>.
The Password setup dialog appears.
Permission Management
User
 ID
abc
 New Password
************
 Confirm P/W
************
4. Enter a new password.
5. Select <OK>.
You change to the password will be applied.
32_ using the DVR
OK
Cancel
Setting the User
Users can be added only if a group was created in <Group> menu.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Permission Management>, and press
[ENTER] button.
3. Use direction buttons (◄ ►) to select <Add> from the
window.
A window for “Add User” appears.
You can configure the Network Viewer settings including
name, ID, viewer, Select Group and password.
Result of the user setup appears in the <User> window.
To change the user property, use “Edit User”.
The “Edit User” window appears when you select a
desired item to be changed in the <User> window.
• Viewer : If you select <Use>, you will be given access to the
Web Viewer and Network Viewer.
Admin
User
Group
 Group
Setup
All Group
Group
Add
Name
ID
Viewer
Del
Previous/Next Page
OK
Cancel
Permission Management
Admin
 Group
User
Group
Setup
Add
User
All Group
Group  Name
Add
Name
ID
Viewer
Del
 ID
 Refer to “Connecting Web Viewer”. (Page 70)
 Viewer
Not Used
 Select Group
ABC
 Password
 Confirm P/W
OK
 For more information about use of Network Viewer, refer to the
Cancel
Previous/Next Page
Network Viewer's user guide.
OK
Cancel
4. When the user setup is done, press <OK>.
Setting Permissions
You can set restricted access for all general users.
Items with restrictions will require logging in for use.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Permission Management>, and press
[ENTER] button.
2. Select <Setup>.
The Restricted Access, Restriction on Network Access,
Auto Log out, Manual Input of ID setup screen appear.
Permission Management
Admin
Setup
Backup
Record Lock
Search
PTZ
Remote Alarm Out
Shutdown
All
 Restriction on Network Access
All Network
 Manual Input of ID
Web Viewer
OFF
ON
• Restricted Access : All menu items allowed for a user can
be set with restricted access.
- Checked (
User
Live View
 Auto Log out
3. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
Group
 Restricted Access
OK
Cancel
) : Restricted
- Not checked (
) : Accessible
 If it is not checked (
) in <Restricted Access>, any user can access the item no matter what the <Group Authority>
setting.
 If it is checked (
) in <Restricted Access>, a user can access the item only if the user has permission in <Group
Authority> setting.
• Restriction on Network Access : Restricts remote access from a <Restricted Access> network.
- All Network : Restricts all access instances via Network Viewer and Web Viewer.
- Web Viewer : Restricts access via the Web Viewer.
• Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of time.
English _33
 USING THE DVR
2. Select <User>.
A window for Add User appears.
Permission Management
using the DVR
• Manual Input of ID : Prompts you to enter the user ID
manually for the login process.
- Checked ( ) : Encloses the registered user IDs with the
[] symbols.
Use the virtual keyboard to enter the user ID.
Login
 ID
*****
 Password
4. When the permission setup is done, press <OK>.
OK
Cancel
System Management
You can check the system version, update to a newer version, as well as data backup and initialization.
Checking the System Information
You can check the current system version, broadcasting system, MAC address. You can update the system.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <System Management>, and press [ENTER]
button.
System Management
System Information
Settings
 System Information
 Software Version
v1.0xh_yymmddhhmmss
2. Check the Software Version, Broadcast Format, and MAC
Address.
 Broadcast Format
NTSC
 MAC Address
00:00:F0:54:FF:FF
• System Information : Shows the current system’s
information.
The values can not be changed by a user.
 Device
No Device
 Version
No S/W Data
 S/W Upgrade
• S/W Upgrade : Updates the DVR’s software.
 Ex : If you connect to a storage device that has upgradable software
installed, and return to the <System Management> menu, the
current software version will be displayed.
Upgrade
Previous
System Management
System Information
Settings
 System Information
 Software Version
v1.0xh_yymmddhhmmss
 Broadcast Format
NTSC
 MAC Address
00:00:F0:54:FF:FF
 S/W Upgrade
 Device
USB2FlashStorage
 Version
v1.0xh_yymmddhhmmss
Previous
34_ using the DVR
Upgrade
• Updating the Software
1. Connect a device storing the software to be updated.
(It may take about 10 seconds to recognize the device.)
 Upgradeable devices include USB memory and network device.
 To update the network, the current DVR should have been
connected to the network.
Upgrade via the proxy server may not be enabled due to the
restricted access.
System Management
System Information
Settings
 System Information
 Software Version
System
Format
 Broadcast
v1.0xh_yymmddhhmmss
Upgrade
NTSC
 MAC Address
Current Version 00:00:F0:54:FF:FF
v1.0xh_yymmddhhmmss
New Version
v1.0xh_yymmddhhmmss
 S/W Upgrade
Do you want to upgrade?
Upgrade
USB2FlashStorage
 Device
OK
Cancel
V1.08_090731170402
 Version
Previous
3. Select <System Information>.
4. When the recognized device appears, select <Upgrade>.
 The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is
same to or older than that of <S/W Upgrade>.
5. Press <OK> in the “System Upgrade” window.
 While updating, it shows the progress.
• Updating progresses with 3 steps as shown in the figure.
System Management
System Information
Settings
 System Information
 Software Version
v1.0xh_yymmddhhmmss
 Broadcast Format
NTSC
S/W Upgrade
 MAC Address
00:00:F0:54:FF:FF
Software upgrading...
 S/W Upgrade
 Device
USB2FlashStorage
 Version
V1.08_090731170402
Upgrade
Previous
System Management
System Information
Settings
 System Information
 Software Version
v1.0xh_yymmddhhmmss
Format
 BroadcastS/W
NTSC
Upgrade
S/W Upgrade
 MAC Address
00:00:F0:54:FF:FF
Software upgrading...
Software upgrading...
 S/W Upgrade
 Device
 Version
Do not turn off during the upgrade.
Upgrade
USB2FlashStorage
V1.08_090731170402
Previous
6. When the updating is done, it automatically restarts.
Do not turn the power off until it finishes restarting.
M
 If “Upgrade Failed” appears, retry from the step 4.
When you experience continued failure, consult the service
center for assistance.
 When you perform S/W update remotely using Smart Viewer,
it may take a max of 3 minutes to complete the update since
Smart Viewer popped up a confirmation message. This is to
guarantee that the DVR set operates stably. For a faster
update, use the USB cable to connect to the DVR set.
English _35
 USING THE DVR
2. Select <System Management> from <System> window.
using the DVR
Settings
You can copy and import the DVR settings by using a storage media.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <System Management>, and press [ENTER]
button.
System Management
Settings
System Information
 Storage Device
2. Select <Settings>.
A window of storage device and load factory default
appears.
0 MB (Remained Capacity)
 DVRUSB
10041400
Export
 USBDVR
No data
Import
Include Network Settings
 Load Factory Default
Default
3. Use direction buttons (◄ ►) to move to a desired
item, and export or import settings data to a storage
device.
Previous
• Storage Device : Shows the connected storage device.
• Export : Exports DVR settings to the connected storage device.
• Import : Imports DVR settings from the storage device and applies to the DVR.
 If <Include Network Settings> is checked, the network settings will be imported too.
• Load Factory Default : If <Default> is selected, a
confirmation dialog for “Load Factory Default” prompts.
Press <OK> to initialize the system to the factory default.
System Management
Settings
System Information
 Storage Device
4. To move to the previous menu, press <Previous>.
Load
 DVRUSB
 USBDVR
0 MB (Remained Capacity)
Factory
Default
10041400
Export
Import
No data
Sure to Default
Setting?
Include
Network Settings
 Load Factory Default
OK
Default
Cancel
Previous
Log Information
You can browse logs on the system and events.
System Log
System Log shows log and timestamp on every system start up, system shutdown, and changes on system
settings.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Log Information>, and press [ENTER] button.
2. Select <System Log>.
Search Day
 Refer to “Using the Calendar”. (Page 29)
Click on the calendar <
Log Information
System Log
First Page
No.
Event Log
2012-01-01
Backup Log
Search
Last Page
Type
Log List
> to display the calendar window.
• Type : When there are too many logs, you can display logs
of the desired format by selecting the type.
3. Use direction buttons (◄ ►) to move to a desired
item, and press <Search>.
36_ using the DVR
View all
Date/Time
Previous/Next Page
Previous
Event Log
Event log shows recorded events on alarms, motion detections and video loss.
It also shows the log and its timestamp.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Log Information>, and press [ENTER] button.
2. Select <Event Log>.
Log Information
System Log
Search Day
First Page
4. Set Search Day, Channel and Type and the press
<Search>.
Last Page
CH
All CHs
Type
View all
No.
Log List
Date/Time
7
Motion Detection [CH 1]
2012-01-01 00:02:14
6
Motion Detection [CH 2]
2012-01-01 00:02:14
5
Motion Detection [CH 3]
2012-01-01 00:02:14
4
Motion Detection [CH 4]
2012-01-01 00:02:18
3
Motion Detection [CH 3]
2012-01-01 00:02:18
2
Motion Detection [CH 2]
2012-01-01 00:02:18
1
Motion Detection [CH 1]
2012-01-01 00:02:18
Previous/Next Page
 Refer to “Using the Calendar”. (Page 29)
Click on the calendar <
Backup Log
Search
2012-01-01
Previous
> to display the calendar window.
Backup Log
You can find out who backed up and the details (backup time, channel, device to use, file format, etc.).
Using the mouse may help make setup easier.
1. In the <System> window, press the up/down () button
to move to <Log Information> and press the [ENTER]
button.
Log Information
System Log
Search Day
First Page
2. Select <Backup Log>.
No.
Backup Log
Event Log
2012-01-01
~
Last Page
Search
2012-01-02
Previous/Next Page
User
Date/Time
3. Use the four direction buttons (◄ ►) to move to a
desired item.
4. Specify a search term and select <Search> in the right
corner.
Backup details for the search term will be listed.
Previous
English _37
 USING THE DVR
3. Use direction buttons (◄ ►) to move to the desired
item.
Event Log
using the DVR
SETTING THE DEVICE
You can setup Camera, Storage Device, Remote Device, POS Device and Monitor.
Camera
Setting the Camera
You can set Video, Audio, Channel Name and Dwell Time of a Camera.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control.
Logout
Return
2. Use the left/right button (◄ ►) to select <Device>.
Device setting menu is selected.
Device
3. Use the up/down buttons () to move to <Camera>,
and press [ENTER] button.
Camera
Storage Device
Remote Device
POS Device
Monitor
4. Select <Camera>.
Displays settings window for Video, Audio, CH Name,
SEQ-Dwell Time, Screen Setup, and Privacy Region.
5. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
• Video
Camera
Camera
PTZ
CH
Video 
CH Name
SEQ-Dwell Time 
1
ON

OFF

CAM 01
5 sec

2
ON

OFF

CAM 02
5 sec

3
ON

OFF

CAM 03
5 sec

4
ON

OFF

CAM 04
5 sec

5
ON

OFF

CAM 05
5 sec

6
ON

OFF

CAM 06
5 sec

7
ON

OFF

CAM 07
5 sec

8
ON

OFF

CAM 08
5 sec

Audio
Previous/Next Page
- <ON/OFF> : You can turn ON/OFF the selected
channel’s camera.
Screen Setup
Privacy Region
OK
- <Covert1> : Shows information other than the video of
the selected channel.
 For privacy protection, it does not display the video while the recording continues.
- <Covert2> : Shows nothing but an empty screen while the recording continues.
• Audio
- If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.
- If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.
 The sound can be output for just a single channel.
38_ using the DVR
Cancel
• CH Name : Up to 15 characters including blanks are allowed. (The first character should not be empty.)
 Refer to “Using Virtual Keyboard”. (Page 30)
• SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out.
 If set to <OFF>, the channel is not listed in the Auto Sequence mode.
 Press the <Init> to initialize settings back to the default 50.
• Privacy Region : You can specify a certain area of the camera
video to be protected for your privacy.
Screen Setup
CH1
50
50
Init
50
OK
Apply to All CH
Cancel
6. When the camera setup is done, press <OK>.
To set the privacy zone
{ Select <Privacy Region>.
| When “Privacy Region” window appears, select a
channel for detection and set the area of motion
detection.
• To set the area in “Privacy Region” window
In the “Privacy Region” window, select desired region
from <
>.
Privacy Region1
• Privacy Region
Individual
You can specify up to 4 privacy zones for each channel,
which can be identified by the color.
1
Purple 2
Green 3
Privacy Region
CH1
Blue 4
OK
Apply to All CH
Cancel
Yellow
• To set the area using <Individual> selection
When selected <Individual>, “Privacy Region” window disappears and you can select cells one by one.
When the motion area setup is done, Right-click to select <Menu> in the context menu or the [MENU]
button on the remote control to display the “Privacy Region” window again.
- Clear All : Selected cell is removed from the Privacy Region.
Clear All
- Menu : After selecting individual motion areas, move to the “Privacy Region” window.
 If selected <Apply to All CH>, selected motion area is applied to all channels.
} When completing the privacy zone settings, click <OK>.
Menu
English _39
 USING THE DVR
• Screen Setup : The video appeared on the screen may vary
depending on the channel’s camera, configure the DVR
display to your preferences.
Select a channel and adjust the < (Brightness)>,
< (Contrast)>, and < (Color)> of the selected channel.
using the DVR
Setting the PTZ
To use Camera’s PTZ functions, ID and protocols of each camera and DVR should be matched.
For other settings, refer to the “Remote Devices” settings. (Page 42)
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Camera>, and press [ENTER] button.
2. Select <PTZ>.
A window of PTZ settings appears.
3. Use direction buttons (◄ ►) to move to a desired
item, and select it.
Camera
PTZ
Camera
Protocol 
CH
ID
1
0
>
None

2
1
>
None

3
2
>
None

4
3
>
None

 5
4
>
None

6
5
>
None

7
6
>
None

8
7
>
None

• ID : Set the ID of the connected camera of each channel.
You can easily setup by using the numeric buttons on the
remote control.
Previous/Next Page
OK
Cancel
• Protocol : Set the protocol of the connected camera of each
channel.
M
 You can check the camera’s ID and protocol if you turn the camera off and on after connecting it to the DVR.
4. When the PTZ setup is done, press <OK>.
Storage Device
You can check information on storage devices.
Confirming Devices
You can check storage devices and their free space, usage as well as status.
Devices available are HDD, and USB devices (Memory, HDD).
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Storage Device>, and press [ENTER] button.
2. Select <Device>.
• No. : Shows the assigned number of the internal HDD.
• Used/Total : Shows the used/total capacity of the storage
device.
• Used : Sets the storage device’s usage.
- USB memory is used for backup purpose only.
• Status/Management : Shows the current status of the HDD,
as in Normal/Check/Replace.
- Normal : Available to use
- Check : Available to use but recommended to replace
- Replace : Requires immediate replacement.
3. To move to the previous menu, press <OK>.
40_ using the DVR
Storage Device
Device
Format
HDD Alarm
Device
No.
Used/Total
Used
Status/Management
HDD
1
0G/494.94G
Internal
Normal
OK
Cancel
Formatting
You can format a storage device.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Storage Device>, and press [ENTER] button.
2. Select <Format>.
A window for selection of device for formatting appears.
Storage Device
Format
Device
Device
HDD Alarm
Select
HDD
1
Used/Total
Used
0G/494.94G
Internal
 USING THE DVR
3. Use direction buttons (◄ ►) to select a device to be
formatted.
Format
OK
4. Select <Format> on the bottom of the screen.
Press <OK> on the “Manage” confirmation window will
start formatting the selected device.
Cancel
Storage Device
Format
Device
Device
Select
HDD
5. When the formatting is done, press <OK>.
HDD Alarm
1
Used/Total
Used
0G/494.94G
Internal
Manage
Formatting deletes all recordings.
M
 Even when formatted, used HDD space will not be 0 GB due
Proceed formatting?
OK
to the space reserved by the system required for operating.
Cancel
Format
OK
Cancel
HDD Alarm
You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,
and its duration.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Storage Device>, and press [ENTER] button.
2. Select <HDD Alarm>.
A window for setting HDD check and replace output ports
and their durations appears.
Storage Device
Device
 Duration
 Replace Alarm Output Port
3. Use direction buttons (◄ ►) to move to the desired
item.
 Duration
• Alarm
HDD Alarm
Format
 Check Alarm Output Port
1
2
BEEP
All
OFF
1
2
BEEP
All
OFF
OK
Cancel
- Alarm signal will output through the alarm out port on the
rear side when selected <1>, <2>.
- If <BEEP> was selected, a beep will sound.
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.
• Check Alarm Output Port : If HDD generates check alarm, the alarm signal will output to the specified alarm
output port.
• Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified
alarm output port.
• Duration : Sets the alarm duration for the alarm signal and beep sound.
English _41
using the DVR
M
 <Check> status means that the HDD is operating but it has problems that require technical examination.
(
) appears on the Live screen.
 <Replace> status means that the HDD has defect and requires immediate replacement.
(
) appears on the Live screen.
4. When the HDD Alarm setup is done, press <OK>.
Remote Devices
You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Remote Device>, and press [ENTER] button.
2. Use direction buttons (◄ ►) to move to the desired
item, and press [ENTER] button.
3. Set the values of each communication setup of the remote
device.
Remote Device
Baudrate
Parity

9600
None
Data

Stop Bit
8

System Keyboard
OFF
ID
1
Remote Control
ON
ID
0
1
Transfer type

Half Duplex
• Baudrate : Baud rate settings of the DVR, PTZ camera and
system keyboard should be matched for proper operations.
OK
Cancel
4. Specify the system keyboard and remote control ID, and
click <OK>.
M
 For changing the remote control’s ID, refer to “Changing the Remote Control ID”. (Page 11)
POS Devices
You can set properties of POS devices connected to the DVR.
A POS device connection requires channel, preset, and Port/Ethernet settings.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <POS Device>, and press [ENTER] button.
POS Device
POS USE
POS Device Setup
2. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
• POS USE : When selected <POS USE>, DVR and POS will
be connected.
POS
CH
Preset 
Port/Ethernet
1
None
No preset
None
2
None
No preset
None
3
None
No preset
None
4
None
No preset
None
5
None
No preset
None
6
None
No preset
None
7
None
No preset
8
None
No preset
None
None
Previous/Next Page
J
 You can change the setting values only if <POS USE> is
checked.
42_ using the DVR
OK
Cancel
• POS Device Setup : Sets the communication setups for the
POS device and DVR.
 It is independent to the Remote Device setup.
POS Device
POS USE
POS Device Setup
POS
CH
1
None
Preset 
No preset
2
NoneSetup
POS
Device
3
4
Baudrate
5
9600
None
None
7
None
8
None
None
No preset
Parity
None

None
6
Port/Ethernet

None
No preset
Data
No preset
8

No preset
None
Stop bit
1
None
Transfer type
None
Half Duplex

None
No preset Cancel
OK
No preset
None
None
No preset
None
Previous/Next Page
OK
 If selected a channel input field, “Sync Channel Setup” window
appears.
 One POS device can be synchronized to up to 16 cameras
(channels), however one channel cannot be synchronized to
multiple POS devices.
POS Device
POS USE
POS Device Setup
POS
CH
Preset 
1
None
No preset
2
None Setup
Sync
Channel
3
4
None
CH
None
5
None
6
None
7
None
8
None
1
2
9
10
Port/Ethernet
No preset
3
4
No preset
11
12
No preset
No preset Cancel
OK
No preset
No preset
OK
“Event” in “Main Menu > Record > Recording Schedule”.
(Page 46)
 Preset name should be unique.
 Use <Add> button to display “Add Preset” window, and set its
name, start string, and end string.
• Port/Ethernet : Sets the port number for the DVR and POS
device connection.
 COM1 : For RS-232C connections
None
5
6
13
14
None
7
None
15
None
8
16
None
None
None
Previous/Next Page
 Channels to be synchronized to a POS device should be set to
• Preset : Sets the name, start and end strings of the receipt
for the preset.
None
No preset
Cancel
POS Device
POS USE
Preset
Setup
POS
1
No.
2
3
POS Device Setup
CH
Add Preset
None
Name
None
 Name
None
Start
4
None
 Start Keyword
5
6
None
 End Keyword
None
7
None
8
None
Port/Ethernet Add
Preset
No preset
End
No preset
None
Input char. Set
None
No preset
None
No preset
None
No preset
None
No preset
None
OKNo preset Cancel
No preset
OK
Cancel
OK
Cancel
Del
None
None
Previous/Next Page
 7001~7016 : For Ethernet connections
3. When the POS Device setup is done, press <OK>.
English _43
 USING THE DVR
• CH : Select the camera to be synchronized to the POS
device.
Cancel
using the DVR
Monitor
You can configure information to be displayed and its format for Spot Out monitor.
Setting the Monitor
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Monitor>, and press [ENTER] button.
2. Select <Monitor>.
Monitor
Monitor
Spot Out
 Event Display
Mode
OFF
 Display
Date
Time
CH Name
Icon
3. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
• Event Display : Sets the dwell time of the event channel
display on the monitor when an event occurs.
If selected <Continuous>, it displays the channel until you
press [ALARM] button to release it.
• Display : Displays only checked items on the monitor screen.
• Multi CH SEQ Time : Sets the interval between automatic display switching in 4-split and 9-split mode of
the Live screen.
• Video Output : You can set the video output mode.
 Multi CH SEQ Time
5 sec
 Video Output
Auto
Display Position Setup
OK
Cancel
- Auto : The default is set to Composite. (In VGA mode, the “SAMSUNG” logo will be displayed)
The main video mode will switch to VGA if a VGA monitor is connected. Then, the Composite port will act
as SPOT source. The monitor distributor is not supported. To switch to VGA mode, turn off the DVR set
and connect the VGA jack. (The VGA monitor will turn on)
- VGA : The main video mode will switch to VGA after the DVR set reboots; the composite source will be
displayed on the spot screen.
- Composite : The main video mode will switch to Composite after the DVR set reboots. In VGA mode, the
“SAMSUNG” logo will be displayed.
4. When the monitor setup is done, press <OK>.
 If you want to change the default output to VGA mode when the live screen is displayed with the beep after the system
booting, press the remote control buttons in sequence: [FREEZE]  [VIEW]  [RETURN (
[VIEW]  [RETURN ( )]. The DVR will switch to VGA mode with the beep after rebooting.
)]  [FREEZE] 
Setting Display position
Some monitors many not display information (camera name, icon, time information, etc.) about the DVR,
depending on the condition. Then, you can change the display position of the data.
1. In the <Device> window, press the up/down () button to move to <Monitor> and press the [ENTER]
button.
2. Select the <Monitor> item.
3. Select <Display Position Setup> in the bottom.
You will move to the <Display Position Setup> window.
4. Use the four direction buttons or the number buttons on
the remote control to adjust the data position.
2012-01-01 01:10:25
Display Position Setup
30
30
30
30
OK
44_ using the DVR
Cancel
Setting the Spot Out
You can set the DVR to output information / video apart from the monitor out.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Monitor>, and press [ENTER] button.
2. Select <Spot Out>.
Monitor
Spot Out
Monitor
 Spot Out 1
SEQ
 Event Display
OFF
Mode
All
Set Mode
 The number of Spot Out terminals differs according to the
 USING THE DVR
model.
3. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
OK
• Spot Out 1 : You can select between Auto Sequence, and
Single.
• Set Mode : A window for “Set Spot Out” appears and you
can set the channel for it.
You can set the dwell time between the screen switching in
“Setting the Device > Camera > SEQ-Dwell Time”.
(Page 39)
Monitor
Spot Out
Monitor
 Spot Out 1
Mode
Set Spot Out
1
 Event Display
5
All
Set Mode
SEQ
2
3
4
6
7
8
9
10
11
12
13
14
15
16
OFF
OK
• Event Display : Specify the time to display the channel
where an event took place on the spot screen.
If selected <Continuous>, it displays the channel until you
press [ALARM] button to release it.
M
Cancel
OK
Cancel
 You can setup using the mouse right button in Live screen.
Refer to “Spot Out”. (Page 25)
4. When the Spot Out is done, press <OK>.
Setting the Screen Mode
You can configure the Live screen and Split Screens.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Monitor>, and press [ENTER] button.
Monitor
Monitor
2. Select <Mode>.
 Live Screen
3. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
 Play Screen
• Live Screen : Select split modes for the Live screen.
16-, 9-, and 4-split screens are included by default.
• Play Screen : Select split modes for the playback screen.
Only the 13-split screen is optional.
Black shows the playback while white shows the Live screen.
Mode
Spot Out
Live
OK
Play
Cancel
4. When the screen mode setup is done, press <OK>.
English _45
using the DVR
SETTING THE RECORDING
You can setup scheduled recording, event recording and other recording related settings.
Recording Schedule
Make your reservation on a date and time to schedule the recording on specified time.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control.
Logout
2. Use the left/right button (◄ ►) to select <Record>.
Record menu is selected.
3. Use the up/down buttons () to move to <Recording
Schedule>, and press [ENTER] button.
Return
Record
Recording Schedule
Event Record Duration
REC Quality & Resolution
Record Option
4. Select <Recording Schedule>.
A window of scheduled recording setup appears.
Recording Schedule
CH1
5. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
All
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
Mon
Tue
Wed
Thu
Fri
Sat
Hol
No Recording
Continuous
Apply to All CH
Event
Both(Cont&Evnt)
OK
• Apply to All CH : If selected <Apply to All CH>, “Apply to
All CH” window appears.
Press <OK> to apply the setup to all channels.
Cancel
Recording Schedule
CH1
All
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
6. When the recording schedule setup is done, press <OK>.
Mon
Apply to All CH
Tue
Wed
Thu
Apply recording schedule to all channels?
Fri
OK
Sat
Cancel
Hol
No Recording
Continuous
Apply to All CH
Event
Both(Cont&Evnt)
OK
46_ using the DVR
Cancel
Recording Color Tags
Color
Function
White
No Recording
Orange
Continuous
Blue
Event
Green
Both(Cont&Evnt)
Description
No schedule / event recording
Scheduled recording only
Event recording only
Both scheduled / event recordings
 USING THE DVR
Each press of a selected cell will cycle through <No Recording>-<Continuous>-<Event><Both(Cont&Evnt)>.
Event Record Duration
You can set the beginning and ending point of a recording on an event.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Record> window to
move to <Event Record Duration>, and press [ENTER]
button.
Event Record Duration
CH
Pre Event 
1
OFF

1 min

2
OFF

1 min

3
OFF

1 min

4
OFF

1 min

5
OFF

1 min

6
OFF

1 min

7
OFF

1 min

8
OFF

1 min

2. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
• Pre Event : The recording of an event will start at a
pre-determined time prior to the actual occurrence of the event.
If it is set to 5 seconds, the recording begins from 5
seconds before the event.
• POST Event : The recording will continue for a
pre-determined time after the actual end of an event.
If it is set to 5 seconds, the recording ends in 5 seconds after an event.
POST Event 
Previous/Next Page
OK
Cancel
3. When the event recording duration setup is done, press <OK>.
REC Quality / Resolution
You can set resolution, fps and quality of recordings by channel, and by recording type of standard / event.
For more information about the resolution, refer to the “Product Specification” section. (Page 96)
Setting Standard Recording Properties
You can set each channel’s resolution, quality and fps for normal recordings.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Record> window to
move to <REC Quality & Resolution>, and press
[ENTER] button.
REC Quality & Resolution
Standard
CH
2. Select <Standard>.
3. When the recording setup is done, press <OK>.
Event
Remaining count : 4CIF(L) : 8
2CIF(M) : 16
Resolution 
CIF(S) : 32
Record Rate 
Record Quality 
1
CIF(S)

7fps

2
CIF(S)

7fps

Level4

3
CIF(S)

7fps

Level4

4
CIF(S)

7fps

Level4
Level4


5
CIF(S)

7fps

Level4

6
CIF(S)

7fps

Level4

7
CIF(S)

7fps

8
CIF(S)

7fps

Level4

Level4

Previous/Next Page
OK
Cancel
English _47
using the DVR
Setting Event Recording Properties
You can set each channel’s resolution, quality and fps for event recordings.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Record> window to
move to <REC Quality & Resolution>, and press
[ENTER] button.
REC Quality & Resolution
Event
Standard
Remaining count : 4CIF(L) : 8
2. Select <Event>.
Event recording setup window appears.
3. Use direction buttons (◄ ►) to move to a desired
item, and select it.
• Resolution : Sets the resolution of the recorded screen.
2CIF(M) : 16
Resolution 
CH
CIF(S) : 32
Record Rate 
Record Quality 
1
4CIF(L)

7fps

Level4

2
4CIF(L)

7fps

Level4

3
4CIF(L)

7fps

Level4

4
4CIF(L)

7fps

Level4

5
4CIF(L)

7fps

Level4

6
4CIF(L)

7fps

Level4

7
4CIF(L)

7fps

Level4

8
4CIF(L)

7fps

Level4

Previous/Next Page
• Record Rate : Image Per Second, means the frames
recorded per a second.
OK
Cancel
• Record Quality : Sets the recording quality.
M
 The estimated total remaining count means the total number of remaining recordings for both standard and event
recordings.
 You cannot increase the remaining count if the current remaining count has reached zero or there is no available
remaining count from any other page. If this is the case, reduce the remaining count for the current page, or do so
for the same channel on any other page.
4. When the Event recording setup is done, press <OK>.
Record Option
Specify whether to stop recording or overwrite the HDD if the HDD is full.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Record> window to
move to <Record Option>, and press [ENTER] button.
Record Option
 Disk End Mode
2. Use direction buttons (◄ ►) to move to a desired
Auto Delete
item, and set the value.
• Disk End Mode : If selected <Overwrite>, recording will
continue despite the HDD full while overwriting the oldest.
If selected <Stop>, the recording will stop when the HDD is
full.
• Disk End Beep : If selected <Stop>, the button is activated.
If you check it, the beep will sound on the disk full and the
recording stops.
• Auto Delete : If you check it, Record Period setup is activated.
If you specify the auto deletion period, the recording data before the period will be deleted automatically.
Overwrite
Disk End Beep

Auto Delete
180
day
The recording information will be deleted.
Do you want to proceed?
OK
OK
 This option will be enabled only if Disk End Mode is set to “Overwrite”.
3. When the recording option setup is done, press <OK>.
48_ using the DVR
Cancel
Cancel
SETTING THE EVENT
You can set recording options for sensor, motion, and video loss event.
Sensor Detection
You can set the sensor’s operating condition and connected camera, as well as alarm output and its duration.
Using the mouse may help make setup easier.
Logout
Return
2. Use the left/right button (◄ ►) to select <Event>.
Event setting menu is selected.
Event
Sensor Detection
Motion Detection
Video Loss Detection
Alarm Schedule
3. Use the up/down buttons () to move to <Sensor
Detection>, and press [ENTER] button.
A window of sensor detection setup appears.
4. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
• Sensor Operation : Sets the operation mode of sensors.
- <OFF> : Sensor does not operate.
- <N.O (Normal Open)> : Sensor is opened.
If the sensor is closed, it generates alarm.
- <N.C (Normal Close)> : Sensor is closed.
If the sensor is open by interruption, it generates alarm.
• Cam : Select a channel to be connected to the sensor.
If selected camera, “Cam Preset setup” window appears.
Select a channel and setup the preset.
 Preset setup can be done in PTZ mode.
Refer to “Preset Setting”. (page 63)
Sensor Detection
Cam 
Alarm 
1
OFF

1
None
10 sec

2
OFF

2
None
10 sec

3
OFF

3
None
10 sec

4
OFF

4
None
10 sec

5
OFF

5
None
10 sec

6
OFF

6
None
10 sec

7
OFF

7
None
10 sec

8
OFF

8
None
10 sec

Sensor
Sensor Operation 
Previous/Next Page
OK
1
2
3
4
5
7
8
Cam
Preset setup
Sensor Operation 
CH 
1
2
3
4
5
6
7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
8
• Duration : Sets the duration of alarm signal and alarm
sound.
5. When the sensor detection setup is done, press <OK>.
Cancel
Sensor Detection
Sensor
6
• Alarm : Sets the alarm output method.
 For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 41)
Duration 
Cam 

Preset

None

None

None

None

None

None

None
Alarm 
1
2

3

4

5

6

7

8

None
CH 
None
9
None
10
None
11
None
12
None
13
None
14
None
15

None
16
OK
Cancel
OK
Cancel
Duration 
10 sec

Preset
10 sec

None

10 sec

None

10 sec

None

10 sec

None

10 sec

None

10 sec

None

10 sec

None

Previous/Next
Page
None

Sensor Detection
Cam 
Alarm 
1
OFF

1
None
10 sec

2
OFF

2
None
10 sec

Alarm
OFF Setup

3
None
10 sec

None

None
10 sec
BEEP 10 sec
6
None
10 sec

7
None
Cancel
None
10 sec

10 sec

Sensor
3
Sensor Operation 
5
OFF
6
OFF

1 
All
7
OFF

8
OFF

4
OFF
4
5
OK
8
2
Duration 

Previous/Next Page
OK
Cancel
English _49
 USING THE DVR
1. Press the [MENU] button on the remote control.
using the DVR
Motion Detection
You can set target detection region and motion, as well as the alarm signal output.
When the motion detection region is set, it detects motion within the area.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Event> window to
move to <Motion Detection>, and press [ENTER] button.
A window of motion detection area setup appears.
Motion Detection
Mode 
CH
2. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
• Mode : Sets whether to activate motion detection.
• Sensitivity : Sets the sensitivity level of the motion detection.
• Alarm : Sets the alarm output method.
Sensitivity 
Alarm 
Alarm Duration 
1
OFF

Level10(High) 
None
10 sec

2
OFF

Level10(High) 
None
10 sec

3
OFF

Level10(High) 
None
10 sec

4
OFF

Level10(High) 
None
10 sec

5
OFF

Level10(High) 
None
10 sec

6
OFF

Level10(High) 
None
10 sec

7
OFF

Level10(High) 
None
10 sec

8
OFF

Level10(High) 
None
10 sec

Previous/Next Page
Motion Region
 For further information on alarm output, refer to “HDD Alarm >
OK
Cancel
Alarm”. (Page 41)
• Alarm Duration : Sets the duration of alarm signal and alarm sound.
3. When the motion detection setup is done, press <OK>.
Setting the Motion Detection Area
{ Select <Motion Region>.
| When “Motion Region” window appears, select a
channel for detection and set the area of motion
detection.
• To set the area in “Motion Region” window
In the “Motion Region” window, select desired region
from <
>.
Motion Region
CH1
• To set the area using <Individual> selection
Individual
OK
Apply to All CH
Cancel
In the “Motion Region” window, you can select cells
individually by using <Individual>.
When selected <Individual>, “Motion Region” window disappears and you can select cells one by one.
When the motion area setup is done, Right-click to select <Menu> in the context menu or the [MENU]
button on the remote control to display the “Motion Region” window again.
- Select : Selected cell is set to be a part of motion detection area.
Select
- Unselect : Selected cell is removed from the motion detection area.
Unselect
- Inverse : Unselected cells are set to be the motion detection area.
Inverse
- Menu : After selecting individual motion areas, move to the “Motion Region” window.
 If selected <Apply to All CH>, selected motion area is applied to all channels.
} When the motion detection setup is done, press <OK>.
50_ using the DVR
Menu
Video Loss Detection
You can set the alarm to be generated on a camera disconnection, which causes a video loss.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Event> window to
move to <Video Loss Detection>, and press [ENTER]
button.
A window of video loss detection area setup appears.
Video Loss Detection
CH
Alarm 
Alarm Duration 
OFF

None
10 sec

2
OFF

None
10 sec

3
OFF

None
10 sec

4
OFF

None
10 sec

5
OFF

None
10 sec

6
OFF

None
10 sec

7
OFF

None
10 sec

8
OFF

None
10 sec

• Video Loss State : Sets whether to activate video loss
detection.
• Alarm : Sets the alarm output method.
Previous/Next Page
Help
OK
Cancel
 For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 41)
• Alarm Duration : Sets the duration of alarm signal and alarm sound.
3. When the video loss detection setup is done, press <OK>.
Alarm Schedule
You can set the conditions and operating hours for scheduled alarms.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Event> window to
move to <Alarm Schedule>, and press [ENTER] button.
Alarm Schedule
Alarm1
2. A window of <Alarm Schedule> settings appears.
All
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
3. Alarm : Sets the alarm output method.
 For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 41)
• <ON> : Marked in orange, and always generates alarm on
scheduled time.
• <OFF> : Marked in white, no alarm is generated even if an
event occurs.
• Event Sync : Marked in Blue, generates alarm only when an
event occurs.
• Apply to All Alarm : Applies the configured schedule to all
alarms.
Mon
Tue
Wed
Thu
Fri
Sat
Hol
OFF
ON
Apply to All Alarm
Event Sync
OK
Cancel
Alarm Schedule
Alarm1
M
 When the alarm is generated on the scheduled time, you can
stop the alarm by canceling the schedule.
All
Sun
Mon
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Apply to All Alarm
Tue
Wed
Apply the alarm scheduling to all?
Thu
4. When the Alarm Schedule setup is done, press <OK>.
Fri
OK
Sat
Cancel
Hol
OFF
ON
Apply to All Alarm
Event Sync
OK
Cancel
English _51
 USING THE DVR
2. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
Video Loss State 
1
using the DVR
BACKUP
You can check the backup device and set the backup schedule by channel or by time.
The product only supports external HDD of USB memory and USB type. (Page 96)
Setting the Backup
You can backup the desired data to a connected device.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control.
Logout
2. Use the left/right button (◄ ►) to select <Backup>.
Backup menu is selected.
Return
Backup
Backup
3. Press the [ENTER] button.
A backup window appears.
You can directly access it from the “Live screen menu”.
(Page 20)
Backup
 Start
2012-01-01 00:01:06
 Overlap
ALL
 End
2012-01-01 08:25:45
~
List0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
• Backup Range : Sets the <Start> and <End> time for the
backup.
• Channel : Sets the channel to backup.
You can select multiple channels.
• Device : Select a backup device from the recognized devices.
• Type : Sets the backup data format.
- DVR : Saved data can be played back only by the DVR.
- SEC : Saves data in the Samsung’s proprietary format with built-in viewer, which supports immediate
playback on a PC.
 Device
USB-Storage
 Type
DVR
 Folder
\20120101\
 Filename
0001
Change
Backup
Used
Free
Check capacity
OK
Cancel
• File Name : You can set the back file name.
 Refer to “Using Virtual Keyboard”. (Page 30)
• Check capacity : Shows the size of the selected backup data, used and available capacity of the selected
backup device.
 Checking will be stopped if the backup size exceeds 200% of the available capacity.
• Overlap : Shows a list of overlapping data on a same time according to the number of data.
It appears when one channel has multiple data on a certain time point due to changing of time or time zone
settings, etc.
 Refer to time and time zone of “Setting the Date/Time/Language”. (Page 28)
52_ using the DVR
5. When the backup setup is done, press <OK>.
 If no available device is recognized for backup, <OK> button is not activated.
J
 The application may slow down during the backup.
 You can switch to the menu screen during the backup in operation, but playback of data is not available.
 If backup has failed, select “Device > Storage Device” and check the free space of the HDD and check also if the
HDD is properly connected.
 Pressing the <Exit> during the backup will return to the previous menu, while the backup progresses.
NETWORK CONFIGURATION
It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with
events. You can configure the network environment which enables such functions.
Connection Mode
You can set the network connection route and protocol.
Setting the Connection
Sets the protocol and environment of the network.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control.
Logout
Return
2. Use the left/right button (◄ ►) to select <Network>.
Network menu is selected.
Network
3. Use the up/down buttons () to move to <Connection
Mode>, and press [ENTER] button.
Connection Mode
DDNS
Live Transfer
Mailing Service
4. Select <Connection>.
A window of connection mode setup appears.
5. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
• Connection Mode : Sets the network connection mode.
• Bandwidth : Sets the maximum data flow to be transferred.
(Upload speed)
Options will vary depending on the selected connection
mode.
- For <Static IP>, <Dynamic IP> : Select one from 50
kbps ~ 2Mbps, and Unlimited.
- For <ADSL>, select one from 50 kbps ~ 600 kbps.
Connection Mode
Connection
Protocol
 Connection Mode
Static IP
 Bandwidth
2Mbps
 IP
192.168. 1.200
 Gateway
192.168. 1.
 Subnet Mask
255.255.255. 0
 DNS
Manual
1
168.126. 63. 1
OK
Cancel
English _53
Your local installer: www.eaglesecuritysolutions.co.uk
 USING THE DVR
M
using the DVR
• IP, Gateway, Subnet Mask, and DNS
- For <Static IP> : You can directly input IP address,
Gateway, Subnet Mask and DNS.
- For <Dynamic IP> : IP address, Gateway, and Subnet
Mask are set automatically.
- For <ADSL> : IP address, Gateway, and Subnet Mask
are set automatically.
• User ID, Password : In case you selected ADSL, provide the
“User ID” and its “Password”.
M
Connection Mode
Connection
Protocol
 Connection Mode
ADSL
 Bandwidth
600kbps
 IP
192.168. 1.200
 Gateway
192.168. 1.
 Subnet Mask
255.255.255. 0
 DNS
Manual
 User ID
ID
 Password
************
1
168.126. 63. 1
OK
Cancel
 DNS server for <Dynamic IP> and <ADSL> can be set by user only if you selected <Manual>.
6. When the connection setup is done, press <OK>.
Setting the Protocol
1. Use the up/down buttons () in <Network> window to
move to <Connection Mode>, and press [ENTER]
button.
2. Select <Protocol>.
3. Use direction buttons (◄ ►) to move to a desired
item, and set the value.
Connection Mode
Connection
Protocol
 Protocol Type
TCP
 Port(TCP)
4520
 Port(UDP)
 Unicast/Multicast
 Multicast IP
~
224.126. 63. 1
 TTL
 Webviewer Port
4524
8000 ~ 8160
Unicast
5
80
• Protocol Type : Select the protocol type between TCP and
UDP.
OK
Cancel
 If selected UDP, selections of Port (TCP), Port (UDP), and Unicast/
Multicast are activated.
 If setting the connection mode to <ADSL>, you cannot select UDP for the protocol type.
• Port(TCP) : Initially, <4520~4524> is set. It increases / decreases by 5.
- TCP: It has better stability and lower speed when compared to UDP, and recommended for internet
environments.
• Port(UDP) : Initially, <8000~8160> is set. It increases / decreases by 160.
- UDP : It has less stability and faster speed when compared to TCP, and recommended for local area
network (LAN) environments.
• Unicast/Multicast : Select one between Unicast and Multicast.
If selected Multicast, Multicast IP and TTL are activated.
- Unicast : Transfers data (UDP, TCP) individually to each connecting client.
- Multicast : Multiple client can receive the data (only in UDP) without putting additional traffic load to the
network.
• Multicast IP : User can directly input.
• TTL : Select from 0 ~ 255. Initial value for the TTL is set to <5>.
• Webviewer Port : Enter the port number for the Web Viewer. Initially, it is set to <80>.
M
 As UDP protocol may cause a packet loss on the network, it is recommended to use TCP protocols.
 If you select UDP protocols and set port forwarding in the IP router, ending up with an unstable network connection,
configure the DMZ settings in the IP router as necessary.
4. When the protocol setup is done, press <OK>.
54_ using the DVR
Connecting and Setting the Network
Networking may differ from the connection method, check your environment before setting the connection
mode.
When no router is used
• Static IP mode
- DVR Network Settings : Set the <Connection Mode> in
<Connection> menu of the connected DVR to <Static IP>.
 Consult your network manager for IP, Gateway and Subnet Mask.
• Dynamic IP (DHCP) mode
- Internet connection : Connect the DVR directly to a cable
modem, DHCP ADSL modem or FTTH network.
Connection Mode
Connection
Protocol
 Connection Mode
Static IP
 Bandwidth
2Mbps
 IP
192.168. 1.200
 Gateway
192.168. 1.
 Subnet Mask
255.255.255. 0
 DNS
Manual
- DVR Network Settings : Set the <Connection Mode> in
<Connection> menu of the connected DVR to <Dynamic
IP>.
1
168.126. 63. 1
OK
Cancel
• ADSL (PPPoE: ID and password certification)
- Internet connection : An ADSL modem is directly connected to the DVR, where the ADSL connection
requires user ID and password.
- DVR Network Settings : Set the <Connection Mode> in
<Connection> menu of the connected DVR to <ADSL>.
 <User ID> and <Password> should be the same to the ADSL
user information.
If you don’t know the ID and password, consult your ADSL service
provider.
Connection Mode
Connection
Protocol
 Connection Mode
ADSL
 Bandwidth
600kbps
 IP
192.168. 1.200
 Gateway
192.168. 1.
1
 Subnet Mask
255.255.255. 0
 DNS
Manual
 User ID
ID
 Password
************
168.126. 63. 1
OK
Cancel
English _55
 USING THE DVR
- Internet connection : Static IP ADSL, leased line, and LAN environments allows connection between the
DVR and remote user.
using the DVR
When a router is used
J
 To avoid IP address conflict with the DVR's static IP, check followings :
• Setting the DVR with a static IP
- Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem or
a router in a Local Area Network (LAN) environment.
• Setting the DVR Network
1. Set the <Connection Mode> in <Connection> menu of the connected DVR to <Static IP>.
2. Check whether the set IP address is in the static IP range provided by the Broadband Router.
IP, Gateway, and Subnet Mask : Consult your network manager.
 Check whether the set IP address is in the static IP range provided by the Broadband Router.
J
 If a DHCP server is configured with starting address (192.168.0.100) and end address (192.168.0.200), you should
set the IP address out of the configured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~
192.168.0.254).
3. Check the Gateway address and subnet mask are equal to those set in the Broadband Router.
• Setting the DHCP IP Address of the Broadband Router
1. To access the Broadband Router’s configurations, open a web browser on the local PC that is connected
to the Broadband Router and enter the router’s address (ex : http://192.168.1.1).
2. At this stage, make the local PC's windows network configurations to the below example :
Ex) IP : 192.168.1.2
Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1
- Once connected to the Broadband Router, it prompts with password. While entering nothing to the User
Name field, enter “admin” into the password field and press <OK> to access the router configurations.
- Access the router’s DHCP configuration menu and set its DHCP server activation, and provide the start and
end address.
Set the start address (192.168.0.100) and end address (192.168.0.200).
M
 Above steps may differ from the router devices depending on the manufacturer.
• Setting Router’s Port Forwarding
1. Set the protocol to <TCP>.
2. External Port Range : Enter the TCP Port set in the
<Port(TCP)> in <Protocol> menu of the connected DVR.
If more than one DVRs are connected to the router, the
TCP port can be different.
3. Internal PC IP Address : Enter the IP address set to the
<IP> in <Connection> menu of the connected DVR.
Connection Mode
Connection
 Protocol Type
TCP
 Port(TCP)
4520
 Port(UDP)
~
Unicast
 Multicast IP
224.126. 63. 1
 TTL
 Webviewer Port
4524
8000 ~ 8160
 Unicast/Multicast
4. Internal Port Range : Set the same to the “External Port
Range”.
M
Protocol
5
80
OK
Cancel
 Above steps may differ from the router devices depending on the manufacturer.
Port forwarding is required when you want to access the DVR connected to the router from outside of the router’s
network.
56_ using the DVR
DDNS
You can set the DDNS site for a remote user’s network connection.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Network> window to
move to <DDNS>, and press [ENTER] button.
2. Use virtual keyboard to enter user inputs.
 Refer to “Using Virtual Keyboard”. (Page 30)
DDNS
 DDNS Site
iPOLiS
 Host Name
www.samsungip...
 User Name
 User Password
http://www.samsungipolis.com/
 USING THE DVR
 DDNS Host Address
 If selected <OFF> or <iPOLiS>, input fields are deactivated.
 If you select <iPOLiS>, the “DDNS host address” item will be
displayed.
OK
Cancel
3. When the DDNS setup is done, press <OK>.
DDNS Setting
DDNS is a short form of Dynamic Domain Naming System.
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters
(ex : www.google.com) to an IP address consisting of numbers (64.233.189.104).
DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS
server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP
system.
Live Transfer
Sets the quality of the image that is transferred from the DVR to the network.
Using the mouse may help make setup easier.
1. In the <Network> setting window, press the up/down
() button to move to <Live Transfer> and press the
[ENTER] button.
The Live Transfer window appears.
Live Transfer
 Resolution
CIF(S)
 Quality
Low
2. Use the direction buttons (◄ ►) to move to a desired
item and set the value.
3. When the live transfer is done, press <OK>.
 The resolution is fixed to CIF(S) and you can specify the transfer
quality only.
OK
Cancel
English _57
using the DVR
Mailing Service
You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs.
M
 If an event occurs with a channel where the camera’s video is set to <OFF> or the remaining recording count is set
J
 If you set the interval of the e-mail notice too short, the e-mail server may consider it as spam that will not be
to <OFF>, only the text notification will be sent to the applicable email address.
transferred normally.
SMTP Setting
Sets the SMTP mail server.
Using the mouse may help make setup easier.
1. In the <Network> setting window, press the up/down
() button to move to <Mailing Service> and press the
[ENTER] button.
2. Select <SMTP>.
You will see the SMTP setting window.
Mailing Service
SMTP
 ServerType
Event
Group
Recipient
SMTP mail Server
 Server
 Port
25
Use Authentication
 User
3. Use direction buttons (◄ ►) to move to a desired item
and set the value.
 Password
************
 Secure Transfer
Never
•
•
•
•
TEST
•
•
•
•
 Sender
ServerType : Displays the connected server type.
Server : Enter a server to connect to.
Port : Sets the communication port.
Use Authentication : Check this if the SMTP server uses user authentication.
The account input box will be activated.
User : Enter a user to use authentication when connecting to the SMTP server.
Password : Enter the password of the SMTP server user.
Secure Transfer : Select one from <Never> and <TLS(if Available)>.
Sender : Use the virtual keyboard to provide the email address.
 Refer to “Using Virtual Keyboard”. (Page 30)
• TEST : Conducts the test on the server settings.
4. When the SMTP setting is done, press <OK>.
58_ using the DVR
ex. user@example.net
OK
Cancel
Event Setting
You can set the interval and type of the event that will be sent to the user.
Using the mouse may help make setup easier.
1. In the <Network> setting window, press the up/down
() button to move to <Mailing Service> and press the
[ENTER] button.
2. Select <Event>.
SMTP
Event
 Event Interval
Group
Recipient
10 min
 Use Event Transfer
Sensor
Motion
Change P/W
HDD Info
Power On/Off
Manual Record
Video Loss
• Event Interval : Set the event interval.
 If a series of events occurs, the e-mail will be sent at the specified
OK
Cancel
interval, not on each event.
• Use Event Transfer : Select an event type to send if an event occurs.
If the selected event occurs, the e-mail will be sent to the group that has the recipient authority.
4. When the event setting is done, press <OK>.
Group Setting
You can set the group to whom the e-mail is sent, and specify the permission for each group.
You can add recipients for each group in the <Recipient> menu item.
The recipient is set separately from the DVR user group.
Using the mouse may help make setup easier.
1. In the <Network> setting window, press the up/down
() button to move to <Mailing Service> and press the
[ENTER] button.
2. Select <Group>.
3. Use direction buttons (◄ ►) to move to a desired item
and set the value.
Mailing Service
SMTP
Group
Event
 Group
Add
Recipient
Delete
Rename
 Recipient Permission
Sensor
Motion
Change P/W
HDD Info
Power On/Off
Manual Record
• Add : Select <Add> and use the virtual keyboard to add a
group.
OK
Video Loss
Cancel
 Refer to “Using Virtual Keyboard”. (Page 30)
• Delete : Deletes the selected group.
• Rename : You can reset the recipient permission of an existing group.
• Recipient Permission : Set the permission of the recipient group.
4. When the group setting is done, press <OK>.
English _59
 USING THE DVR
3. Use direction buttons (◄ ►) to move to a desired item
and set the value.
Mailing Service
using the DVR
Recipient Setting
You can add/remove a recipient(s) to/from the specified group and edit the group if necessary.
Using the mouse may help make setup easier.
1. In the <Network> setting window, press the up/down
() button to move to <Mailing Service> and press the
[ENTER] button.
Mailing Service
SMTP
 Group
Event
Group
2. Select <Recipient>.
Recipient
Group
All Group
Add
Name
e-Mail Address
Del
3. Use direction buttons (◄ ►) to move to a desired item
and set the value.
Previous/ Next Page
OK
• Add : You can select a recipient name, e-mail address or
group.
You should have created a group in the <Group> menu
item before you can add a user to the group.
 For inputting the recipient name and email address, refer to
“Using Virtual Keyboard”. (Page 30)
Cancel
Mailing Service
SMTP
 Group
Event
Recipient
Group
ABC
Group
Add
Add recipient
Name
e-Mail Address
Del
 Name
 Email
 Select Group
ABC
OK
Cancel
4. When the recipient setting is done, press <OK>.
Previous/Next Page
OK
60_ using the DVR
Cancel
CONTROLLING A PTZ DEVICE
The DVR enables you to adjust the settings of a PTZ camera as well as an ordinary one to your preference.
PTZ Device
The PTZ device can be activated only if a channel in connection with the PTZ camera is selected.
Getting started with PTZ
 Using the remote control buttons
Press the [PTZ] button on the remote control.
Scene Mode
2012-01-01 01:10:25
Spot Out


PTZ Control
 Using the launcher menu
Click PTZ <
PTZ
> to display the live launcher.
Zoom In
Audio Off
Freeze
Stop Alarm
Record
 Using the right-click menu in Live mode
Right-click any area on the screen to display the context menu, and
select <PTZ Control>.
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
 Using icons on the live screen
Click the PTZ <
M
> icon on the live screen.
2012-01-01 01:10:25
 The PTZ function is available only if the PTZ camera is
connected so that the PTZ icon is displayed on the screen.
English _61
 USING THE DVR
The PTZ camera is available, only if a channel is selected, in the following way :
using the DVR
Using the PTZ camera
You can use one camera to perform all functions of PAN, TILT and ZOOM for monitoring multiple places and
set the preset to your preference in a desired mode.
1. Launch the <PTZ Control> menu.
> icon on the bottom right corner turns
As the PTZ <
yellow, you access the “PTZ Control” mode to display the
“PTZ Control” menu.
M
2012-01-01 01:10:25
 Be sure to configure PTZ working environments before
operation, since the PTZ Working(Active) mark can be
appeared to be activated even when PTZ is not operative.
PTZ Control CAM01
Auto Pan
Select
Scan
Select
Pattern
Select
Camera Setup
Select Preset
Save
Rename
2. Use the PTZ wheel in the launcher menu to adjust the
monitoring area, or use the direction buttons (◄ ►) on
the remote control to move the camera to a desired place.
• PTZ Wheel : Clicking a nearer point to the center will move in that direction slowly; clicking a farther point
from the center will move fast.
Preset
Select
Delete
Delete
All All
Delete
Delete
Exit
 Keep clicking left to rotate the lens counter clockwise; keep clicking right to rotate the lens clockwise.
• Zoom (
•
•
•
•
) : You can use the Zoom function of the PTZ camera.
IRIS (
) : Adjusts the intensity of radiation incoming to the iris.
Focus (
) : Enables you to adjust the focus manually.
Auto Pan : The camera automatically runs between the two points that you selected.
Scan : The camera moves to the preset points in the specified sequence.
If multiple presets are specified, the PTZ camera will automatically move to all of the preset points one at a
time.
• Pattern : Makes the PTZ camera remember and follow the past route.
 The functions of Auto Pan, Scan and Pattern are supported in the protocols of Samsung, Panasonic and Pelco, and are
different in terms of the name and setting, depending on the protocols of Samsung, Panasonic and Pelco.
(Panasonic : Auto Pan, Sequence, Sort / Pelco : Auto Pan, Frame Scan (Scan), Pattern)
M
 Before entering the PTZ device control mode, set the values of the PTZ device in the <Setting the PTZ> menu.
(Page 40)
62_ using the DVR
Preset Setting
A preset is a set of specific target points of a PTZ camera, and up to 127 presets per a camera can be stored.
1. In PTZ Control mode, use the direction buttons to adjust the camera in a desired direction.
2. Select the <Save> key.
The virtual keyboard for inputting the preset will appear.
 Refer to “Using Virtual Keyboard”. (Page 30)
Save : You can save the preset settings.
Rename : You can change the settings of the existing presets.
Delete : Deletes the selected preset.
Delete All : Deletes all existing presets.
M
 If you replace the camera of the channel that stores the preset list with a new one, you should reset the preset
accordingly.
3. Press <OK>.
The preset will be saved as a name that you entered.
Camera Setting
A PTZ camera has its own menu system. Optimize the PTZ camera according to the DVR.
1. Connect the PTZ camera to the DVR and run the PTZ
camera again to display the camera’s protocol setting
window.
2. Check the protocol ID of the camera.
 In “Device > Setting the PTZ”, enter the PTZ camera ID in the
ID input box of the channel that is connected to the PTZ camera.
(Page 40)
2012-01-01 01:10:25
SAMSUNG PROTOCOL
ADDR
TYPE
BAUD
LENS
TILT
PAN
3. Select <Camera Setup> in the PTZ Control menu.
The camera-specific menu appears.
2012-01-01 01:10:25
** MAIN MENU **
 You can configure the settings of only those cameras that support
the protocols of Samsung, Pelco D/P, AD and Panasonic.
 If you are setting Auto Pan or Pattern in the camera menu, press
and hold the appropriate button for a certain time so that the button
operation can be different from that in normal PTZ setting.
0
RS-485,HALF
9600
OK!
OK!
OK!
Camera Setup

Exit
CAMERA SET...
...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
CLOCK SET...
SYSTEM INFO...
English _63
 USING THE DVR
•
•
•
•
search & play
SEARCH
You can perform the search for recorded data by the time or by the search criteria such as an event.
You can access the <Search> menu directly in Live mode.
1. In Live mode, right-click any area of the screen.
The Live menu appears.
Scene Mode 
2012-01-01 01:10:25
Spot Out

Audio Off
Freeze
2. Select <Search>.
Or, press the [SEARCH] button on the remote control.
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
3. The Search menu appears.
2012-01-01 01:10:25
 If you have not checked “POS USE” in the “Main Menu >
Device > POS Device” menu, the Search menu does not
include the “POS Search” item. (Page 42)
Return
Time Search
Event Search
4. The search can be restricted by the Auto Delete function.
Refer to “Setting the Recording > Record Option”.
(Page 48)
M
Backup Search
POS Search
Motion Search
 Overlapped data : It only appears if there exists overlapped
data on a certain time, produced due to the change of DVR’s
time setup. The latest data comes first, from <List0>.
It does not appear in <Backup Search>.
Time Search
You can search for recorded data of a desired time.
As the time to display may be different depending on the time zone and the DST standard time, the time of
data recorded in the same time can be displayed differently depending on time zone and DST settings.
Using the mouse may help make setup easier.
1. Select <Time Search> in the <Search> menu.
2. Select a date to search.
Time Search
Go to First
2012-01-01
 Refer to “Using the Calendar”. (Page 29)
3. The record data on the specific date will be listed.
The display bar is different according to the data type.
So check the data type for the color in the left pane.
4. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
•
•
•
•
Go to Last
Overlapped Data List1
Zoom In
Zoom Out
00:01
All
Data
CAM 01
CAM 02
CAM 03
2012/01/01 00:01:17
Standard
Schedule
Motion
Sensor
V.Loss
Etc
CAM 04
CAM 05
CAM 06
CAM 07
Previous/Next Page
Play
Return
Go to First : Move to the earliest recording date.
Go to Last : Move to the latest recording date.
Time : Enter a time to perform the search or use the up/down button <>> to select one.
Previous/Next Page : Moves to the previous / next page. (Use the remote control or the buttons on the front
panel.)
64_ search & play
• Zoom In : The map enlarges in detail.
It will switch in the sequence of 24 hours - 16 hours - 8 hour
- 4 hours.
• Zoom Out : The map will switch in the reverse order of the
detailed mode above.
It will switch in the sequence of 4 hours - 8 hour - 16 hours
- 24 hours.
M
Time Search
Go to First
2012-01-01
Go to Last
Overlapped Data List1
Zoom In
Zoom Out
00:01
All
Data
CAM 01
CAM 02
CAM 03
2012/01/01 00:01:17
CAM 04
Standard
Schedule
Motion
Sensor
V.Loss
Etc
CAM 05
CAM 06
CAM 07
 Double-click a desired time to zoom it in/out.
Previous/Next Page
Play
Return
 SEARCH & PLAY
• Preview : Click <Channel> and select (click, drag) a time in
<Duration> to display a still image for the portion.
- If the selected channel does not contain any recorded data, it will be marked black.
5. Select a data item and click <Play>.
The screen switches to the data playback mode.
Event Search
You can search for events by the channel and play them.
Using the mouse may help make setup easier.
1. Select <Event Search> in the <Search> menu.
2. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
 All record events on a specific date will be found. (Normal/
Event Search
CAM 01
2012-01-01
Overlapped Data
List1
Go to First
Schedule recording included)
• Date/Time Preview : If you select a data item in the list, the
still image of the selected data will be displayed in the left
preview pane.
• Event : Displays the type of the event that occurred.
Go to Last
No.
Date/Time Preview
3
02:47:54 ~ 02:48:59
Motion
2
00:39:06 ~ 00:40:30
Motion
Event
1
00:01:22 ~ 00:02:28
Motion
2012/01/01 00:01:22
Previous/Next Page
Play
Return
3. Select a data item and click <Play>.
The screen switches to the event data playback mode.
Backup Search
Searches for backup data in the connected backup device.
Only data in the format of DVR is included in the search.
Refer to <Type> in “Backup > Setting the Backup”. (Page 52)
Using the mouse may help make setup easier.
1. Select <Backup Search> in the <Search> menu.
2. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
• Record Period : Displays the record period.
• Channel info : Displays the recorded channel.
• Play Start Time : Select a time that you start playing.
3. Select a data item and click <Play>.
The screen switches to the backup data playback mode.
Backup Search
USB:USB2FlashStorage
No.
Folder
File Name
1
20120101
16190000
Previous/Next Page
 File Name 16190000  Channel info 1
 Record Period
2012-01-01 01:01:01 - 2012-01-01 01:01:10
 Play Start Time
2012-01-01
Play
01:01:01
Return
English _65
search & play
POS Search
You can search for data in the POS device that is connected to the DVR.
You can use the mouse to select the related items.
1. Select <POS Search> in the <Search> menu.
 The <POS Search> item will be active only if you check the
“Use POS” option from “Device > POS Device”. (Page 42)
POS Search
Date/Time
2012-01-01 02:41:18
Case Sensitive
Overlapped Data
List1
2. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
 You can enter specific text to refine your search.
• Keyword : Use the virtual keyboard to enter a keyword.
• Search Criteria :
2012-01-01 03:41:18
Keyword
Go to First
Search
Whole Word
Go to Last
POS
CH
Start Date/Time
1
1
2012-01-01 03:41:15
CHANGE _
1
1
2012-01-01 03:41:15
CASH _
Keyword
1
1
2012-01-01 03:41:10
CASH _
2012/01/01 03:41:15
CHANGE
5.95
Previous/Next Page
Play
Return
- <Case Sensitive> : If selected, search will be performed
case-sensitively.
- <Whole Word> : If selected, only the exact matches with the keyword will be found.
• Preview : Select a data item in the list to display the preview image.
Information about the image will be displayed on the bottom of the screen.
•
: You can use these buttons to accelerate your search if you have a huge list of search results.
3. Select a data item and click <Play>.
The screen switches to the POS data playback mode.
Motion Search
If a motion is detected in each channel, you can set a desired area to perform the search.
You can use the mouse to select the related items.
1. Select <Motion Search> in the <Search> menu.
2. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
 If you set the motion area to <Manual Area>, the <Setup>
Motion Search
Channel
CAM 01
Date/Time
2012-01-01 03:41:18
Overlapped Data
Motion Region
Setup
All Area
2012-01-01 05:11:44
Search
Go to First
Go to Last
List1
No.
Start Time
7
01:01:30
6
01:01:25
5
01:01:20
4
01:01:15
3
01:01:10
2
01:01:05
1
01:01:01
button will be activated.
• Motion Region : Select an area to perform the search.
~
2012/01/01 01:01:30
- All Area : Searches for all areas of the selected channel.
Previous/Next Page
- Current Area : Searches for the motion area for each
channel specified in “Motion Detection >
Setting the Motion Detection Area”. (Page 50)
Play
Return
- Manual Area : You can set the motion area manually.
• Setup : The Setup button will be activated only if you have
set the motion area to Manual. Press this button to display
the area setting window.
• Date/Time : The Date/Time will be automatically set by the
hour, and the end time will be automatically set to one hour
later than the start time if it is set.
• Preview : Select a data item in the list to display the still
image of the item.
3. Select a data item and click <Play>.
The screen switches to the motion data playback mode.
66_ search & play
Motion Region
CH1
Individual
OK
Cancel
Apply to All CH
PLAYBACK
Play
You can play data stored in the HDD and backup a desired portion of the data.
Using the mouse may help make setup easier.
1. In Live mode, click <Play> in the right-click menu or
<
> in the launcher menu, or press the Play button on
the remote control.
Scene Mode 
2012-01-01 01:10:25
Spot Out

Audio Off
 SEARCH & PLAY
Freeze
Stop Alarm
Record
2. Use the up/down button () to select a menu.
Play
 For data search, refer to <Search>. (Page 64)
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
3. Select a data item and click <Play> in the Search menu.
The selected data is played and the play launcher appears
on the screen.
2012-01-01 01:10:25
 If there is an existing data, <Play> will start immediately without
performing the search.
• Playback Information : Displays the date and time of the
current data in the top corner.
REC
> to set the current time to the start
• Backup : Click <
time of backup; you can specify a backup area using the
mouse (yellow triangle).
Click <
> again to set the current time to the end time of
the backup and the “Backup Range” window appears.
- Type : Supports formats of DVR and SEC.
Refer to a list of formats in “Setting the Backup”.
(Page 52)
- Device : Select a backup device.
- Check Capacity : Enables you to check the capacity of the
selected storage device.
4. If you want to return to the Live screen in Play mode, click <
[] button on the remote control.
Backup Range
 Start
 End
2012-01-01 00:01:06
2012-01-01 01:10:25
 Device
USB Storage
 Type
 Folder
\20120101\
 Filename 0001
DVR
Change
Backup
Used
Free
Check capacity
OK
Cancel
> in the launcher menu or press the
English _67
search & play
Using the Playback Button
REC
Part Names
Functions
Play Timeline
Indicates the current playback point, and can be used to move.
b
Skip Backward
Moves backward by unit time.
c
Backward Fast
Play
Used for quick backward playback.
Backward Slow
Play
Used for backward frame-by-frame search while in PAUSE.
Step Backward
Moves backward by one frame at a time.
Pause
Stops playing the current video temporarily.
Stop
Stops playback and moves to the live screen.
Step Forward
Moves forward by one frame at a time.
Forward Slow
Play
Ensured to play forward up to 4 channels simultaneously at a low speed.
 In a split mode, the real time playback may not be supported, depending on the record
quality, resolution and number of channels. And some frame rates may be supported.
Forward Fast
Play
Used for quick forward playback.
Skip Forward
Moves forward by unit time.
Return
Return to the search setup screen.
m
Audio
n
REC
Records all channels in Live mode.
Partial Backup
Begins backup of the selected section of the video being played, with the specified starting/
ending point.
Mode Switch
Click a desired playback mode or press [MODE] to switch the screen mode in sequence.
 The grey area in the center of the 13-split mode plays the Live channel.
The default channel of the Live mode is CH1, which can be changed later.
68_ search & play
Sets Audio ON/OFF.
 If using both web view and DVR set simultaneously, the audio signal will be output from the
DVR set.
web viewer
INTRODUCING WEB VIEWER
What is Web Viewer?
 WEB VIEWER
Web Viewer allows remote access to your DVRs. You have
access to live video, archived video, PTZ control (if configured),
etc.
Product Features
• Remote connection using the browser
• PTZ camera control enabled
• Supports 1,4,9,16 camera viewing formats (maximum of 16
cameras in the list).
• Gets JPEG, BMP format images to print and save to “Print
or Save JPEG, BMP format images”.
• Record video in AVI format-compatible with popular media players. (needed the H.264 codec)
System Requirements
The following lists the minimum suggested hardware and operating system requirements needed to run the
Web Viewer.
OS
Web Browser
CPU
Windows XP Professional
Windows 2000
Windows Vista Home Basic / Premium
Windows 7
Internet Explorer 6.0.2900.2180 or higher
Intel Pentium 4 / 2 GHz
Memory
512 MB
Monitor
High Color 16-bit 1024 x 768
HDD
50 MB(Installation space required)
* Additional HDD space required for recording.
Recorded file size will vary depending on recording quality settings.
English _69
web viewer
CONNECTING WEB VIEWER
1. Open your web browser and type the IP address or URL
of DVR into the URL address box.
M
The basic URL of the DVR is as following in case of MAC
address :
 http://www.samsungipolis.com/Product ID
– Product ID : ID that is registered at iPOLiS homepage.
 You can also use registered URL which setups up in the Setup menu of your DVR.
2. Set the Admin ID and password same to those of the DVR
Admin.
For general users, enter the DVR user ID and password.
J
 The default password can be exposed to a hacking thread so
M





it is recommended to change the password after installing the
product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
It allows up to 4 simultaneous access including the Admin and general users.
It does not allow multiple login of the Admin user.
Initial password of the Admin user is set to “4321”.
Password of the Admin and general users can be changed in <Permission Management> menu of the DVR.
Normal users should have set <Viewer> under <Permission Management> to “Use” before connecting to the
Web Viewer. (Page 33)
 All settings are applied by the DVR’s settings.
 If you change such as the permission settings with logged in to the Web Viewer, you may go back to the log in
screen.
3. Click <Install ActiveX Control…>.
Downloading ActiveX control may take several minutes
according to the security settings on your PC.
4. Click <Install>.
70_ web viewer
5. You may have “Windows Security Alert” that attempts to
block this with the Windows Firewall. In that case, click
<Unblock> to start Web Viewer.
6. Installation is complete.
Now you can see the main screen of Live Viewer.
 WEB VIEWER
USING LIVE VIEWER
b
c
The Live Viewer screen consists of following :
This displays the IP address and the model name of the connected DVR.
b These menus consist of <LIVE>, <SEARCH>, <SETUP>, <ABOUT>.
c These buttons are used for the screen split and full screen mode.
Shows the IP address and model name of the connected DVR.
Select to turn the sound on/off.
Select <DVR Time> or <PC Time> for the OSD time information display setting of the Live Viewer.
These buttons are used for sequence and changing the screen channel.
These buttons are used for capture, print, and save the image.
Shows the channel of the connected DVR.
These buttons are used for PTZ related functions.
This displays the screen for connected camera with DVR.
M
 The resolution is set to 1024X768 pixels.
 The initial split-screen mode is set according to the number of channels connected to DVR. You can change the
split-screen mode by clicking buttons for split-screen modes.
English _71
web viewer
OSD Information Display
Display the channel number and video size of the connected DVR.
b This icon will appear if the audio signal is currently being output.
b
c The current date and time will be displayed according to the
selected time information display setting <DVR Time> or <PC
Time>.
Alarm icon appears when alarm is issued.
It disappears when pressed the [ALARM] button of the DVR.
Motion icon appears when motion is detected.
It disappears when pressed the [ALARM] button of the DVR.
It displays whether the PTZ controls are active.
M
 If you have set PTZ cameras for the DVR, “PTZ” is displayed on the
screen. Select a PTZ camera channel and use the [PTZ] button for
camera control.
c
Split-Screen
You can change the split mode by clicking each number icon.
SINGLE MODE
QUAD MODE
NINE MODE
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“SINGLE MODE”.
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“QUAD MODE”.
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“NINE MODE”.
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“SIXTEEN MODE”.
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“FULL SCREEN MODE”.
Double clicking on the screen or pressing any button of the keyboard
returns to the previous mode.
72_ web viewer
SIXTEEN MODE
Connected DVR
This displays the IP address and the status of the connecting DVR.
M
 Connection failure message
No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of users is exceeded.
 The number of simultaneous connections are limited to 4.
 WEB VIEWER
Setting the display of the OSD time information
Select <DVR Time> or <PC Time> for the OSD time information display
setting.
• DVR Time : Based on the time of the connected DVR
• PC Time : Based on the time of the PC currently running the Web Viewer.
• Audio : Sound On/Off
Changing the Live Screen Mode
 16-split mode does not support “SEQUENCE”, “PREVIOUS” and “NEXT”.
• SEQUENCE : When this button is clicked, screens are switched at a
preset interval.
In SINGLE MODE, the channel numbers are sequentially switched from
1 to 16.
In QUAD MODE, the screens are changed like 1st 4 channels (1~4)
 2nd 4 channels (5~8)  3rd 4 channels (9~12)  4th 4 channels
(13~16).
In NINE MODE, the screens are changed from 9 channels (1~9) to 7
channels (10~16).
 Preset interval (10 seconds)
• PREVIOUS : When this button is clicked, the previous screen appears.
In SINGLE MODE, the channel numbers are switched in reverse order.
In QUAD MODE, the screens are changed like 1st 4 channels (1~4) 
2nd 4 channels (13~16)  3rd 4 channels (9~12)  4th 4 channels (5~8).
In NINE MODE, the screens are changed from 9 channels (1~9) to
7 channels (10~16).
English _73
web viewer
• NEXT : When this button is clicked, the next screen appears.
In SINGLE MODE, the channel numbers are sequentially switched from 1 to 16.
In QUAD MODE, the screens are changed like 1st 4 channels (1~4)  2nd 4 channels (5~8)
 3rd 4 channels (9~12)  4th 4 channels (13~16).
In NINE MODE, the screens are changed from 9 channels (1~9) to 7 channels (10~16).
 If 16-channel DVR is connected, clicking “NEXT” in QUAD MODE is to change the screen as shown in the picture.

(CH1 to CH4)

(CH5 to CH8)

(CH9 to CH12)
(CH13 to CH16)
16-channel DVR
Saving the Live Screen on the PC
• CAPTURE : Saves the current screen into a BMP or JPEG
file.
M
 The default saving path is “C:\Program Files\Samsung\DVR
Web Viewer\SnapShot\Live”. To change the saving path, click
<SAVE PATH (
)> button and then select the path you
want. For Windows Vista or 7, the saving path is “C:\users\
(user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\
SnapShot\” by default.
 The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_
index”
Ex) 192.168.1.200_554_20120101_134132_01_00
• PRINT : Prints out the selected screen out of the currently
displayed live screens. It also prints the IP address, time,
camera number and the current event status together.
74_ web viewer
• RECORD : Saves the current image on the screen and
saves it as a avi video file.
M
 To record it, it is required at least 1GB of available space.
 The default saving path is “C:\Program Files\Samsung\DVR
Changing the Live Screen Channel
• Blue numbers : The channel connected to the current live
screen
• Gray numbers : The channel not connected to the current
live screen
Using PTZ Camera
Click the direction buttons to control the camera.
•<
>
You can zoom in or out an image by using the ZOOM button.
•<
>
You can adjust the entering light amount by using the IRIS button.
•<
>
You can adjust the focus by using the FOCUS button.
English _75
 WEB VIEWER
Web Viewer\VideoClip\Live”. To change the saving path, click
)> button and then select the path you
<SAVE PATH (
want. For Windows Vista or 7, the saving path is “C:\users\
(user ID)\AppData\Local-Low\Samsung\DVR Web Viewer\VideoClip\”.
 The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_
index”
Ex) 192.168.1.200_554_20120101_135105_01_00
 For AVI Save, you need the H.264 codec for playing saved files.
 HDD Minimum Free Size : During the recording, if there is no more capacity available in the HDD than set free space
will prompt with a popup message : “Cannot record due to insufficient disc space in the HDD”.
web viewer
• MENU : Appears the camera menu screen.
• Preset : Moves the lens direction to a preset direction.
1. If you click a preset, the camera moves to the selected
preset's position.
2. You can delete the selected preset or all presets.
3. You can save a new preset number and name.
M
 You can save presets up to 127.
• Auto Pan : Moves the camera lens direction between
2 points set for the camera.
• Scan : Moves the camera lens direction between 2 preset
points of the camera.
• Pattern : You can set camera various movement patterns
such as zoom, move, etc. so that a camera automatically
moves according to the pattern.
M
 While the DVR controls a PTZ camera, Web Viewer cannot
control the camera.
 Camera menu setup is only available for camera supporting
the function.
 Each function of PTZ is same to that of the DVR.
 Pan/Tilt of the Smart dome camera is manipulated
automatically to center the camera to the mouse clicked
point.
 If you drag the mouse using the left button on a certain point,
Pan/Tilt of the Smart dome camera is manipulated
automatically to center the camera to the middle point between the dragging start and end position.
Upward dragging will zoom out, while downward dragging will zoom in.
 Tilt of Power PTZ operates properly within 45°.
 Power and Pan Tilt functions are only available for camera supporting the functions.
Ex : Samsung SCC-C6475
76_ web viewer
USING SEARCH VIEWER
b
c
The Search Viewer screen consists of following :
This displays the IP address and the model name of the connected DVR.
b There are 4 tabs available: <LIVE>, <SEARCH>, <SETUP>, <ABOUT>.
c Switch to a split mode.
Shows the IP address and model name of the connected DVR.
Select to turn the sound on/off.
These buttons are used for capture, print, and save the image.
This displays a calendar at which you can search the recorded video.
The duplicate check list will appear If there are found duplicates in the same timeline.
The duplicated items will be listed in latest-first order.
This displays a timeline at which you can search the recorded video by the time.
These buttons are used for controlling playback.
This displays the screen for playback of recorded video.
M
 <SEQUENCE>, <PREVIOUS>, <NEXT> buttons are not available in SEARCH menu.
 During the DVR backup, you may have a trouble accessing CMS & Web Search.
English _77
 WEB VIEWER
web viewer
Split-Screen
You can change the split mode by clicking each number icon.
SINGLE MODE
QUAD MODE
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“SINGLE MODE”.
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“QUAD MODE”.
M
 Only SINGLE and QUAD MODE are available in SEARCH menu.
 If 16 channel DVR is connected, you can select a mode from SINGLE to
SIXTEEN MODE.
Connected DVR
The IP of the connected DVR will be displayed.
Select to turn the sound on/off.
M
 Connection failure message
No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of users is exceeded.
 The number of simultaneous connection is limited to 2.
78_ web viewer
Saving the Live Screen on the PC
• CAPTURE : Saves the current screen into a BMP or JPEG
file.
M
 The default saving path is “C:\Program Files\Samsung\DVR
• PRINT : Print out the current screen. It also prints IP
address, time, camera number and current event state.
• RECORD : While in playback, press this button saves the
video data of the selected channel as an AVI file. (It is saved
in the designated folder on your PC.)
To stop recording, click this button again.
M
 To record it, it is required at least 1GB of available space.
 The default saving path is “C:\Program Files\Samsung\DVR
Web Viewer\VideoClip\Search”. To change the saving path,
click <SAVE PATH (
)> button and then select the path you want. For Windows Vista or 7, the saving path is
“C:\users\(user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\VideoClip\”.
 The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_
index”
Ex) 192.168.1.200_554_20120101_135105_01_00
 For AVI save, you need the H.264 codec for playing saved files.
English _79
 WEB VIEWER
Web Viewer\SnapShot\Search”. To change the saving path,
click <SAVE PATH (
)> button and then select the path
you want. For Windows Vista or 7, the saving path is “C:\
users\(user ID)\AppData\LocalLow\Samsung\DVR Web
Viewer\SnapShot\”.
 The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_
index”
Ex) 192.168.1.200_554_20120101_134132_01_00
web viewer
Searching the Recorded Video in the Calendar
If the video data has been recorded on a date, the date is
distinguished in green. If you click the date, the recorded video
information is displayed in the time line. When you click
<Today>, it will be synchronized with the system time (date) of
the current PC.
Check duplicates
If there are found duplicates in the same timeline after you changed the DVR
time, those duplicates will be listed in the <0> order with the latest one on top.
Searching the Recorded Video in the Timeline
It displays the recorded video data status on the DVR after a date is
selected. The normal mode displays the time ranging from 0 to 24 Hours
while the extension mode displays the time every 2 hours.
[Normal Mode]
• If you click < > button, it changes to the extension mode.
• Each time line represents 1 hour.
[Extension Mode]
• If you click < > button, it changes to the normal mode.
• Each time line represents 5 minutes.
M
 The channels are ranging from CH01 to CH16.
80_ web viewer
Controlling Playback
b
c
 WEB VIEWER
Fast Backward : Play the video reversely. (at x2 ~ x64)
b Reverse Play : Performs Reverse Play.
c Play : Performs playback.
Fast Forward : Play the video forward. (at x2 ~ x64)
Go to First : Moves the beginning time of recorded video in the time line.
Step Backward : Performs one step reverseplay by one frame.
Pause : Stops the playback temporarily.
Step Forward : Performs one step forward by one frame.
Go to Last : Moves the last time of recorded video in the time line.
M
 Only the admin account can play the audio signal during the playback.
If using both web view and DVR set simultaneously, the audio signal will be
output from the DVR set.
VIEWER SETUP
You can configure the DVR settings remotely on the network.
To configure the DVR settings, click <Setup>.
System
You can configure the various settings of the DVR system.
Date/Time/Language
For more information, refer to <Date/Time/Language> in the <System Setup> menu. (Page 28)
1. Select <Date/Time/Language> in the System menu.
2. Configure the DVR settings according to your system
environment.
• Date/Time
Set the date and time.
English _81
web viewer
• Time Synchronization Setup
Set the time synchronization.
• Display
Date Format : Set the date type.
Time : Select a time format to display on the screen.
• DST (Daylight Saving Time)
DST is displayed an hour ahead of the standard time of the
time zone.
• Language
Select a preferred language for the DVR.
Holiday
You can set specific dates to Holidays according to your
preferences.
For more information, refer to <Setting Holiday> in the
<System Setup> menu. (Page 29)
Permission Management
For more information, refer to <Permission Management> in the <System Setup> menu. (Page 30)
• Admin
 You can change the admin ID or the password.
 You can type the ID with alphanumeric characters only.
 For the password, use alphabets and special characters excluding
< \ > and <“>.
82_ web viewer
• Group
Users are classified into groups and the permission can be
set according to the group.
 First of all, add a group.
 WEB VIEWER
• User
You can add, change or remove a user or users.
• Setup
You can set the user permission.
System Management
For more information, refer to <System Management> in the <System Setup> menu. (Page 34)
• System Information
You can see information of the current system.
Check the software version, broadcast format and
MAC address.
English _83
web viewer
Device
You can check a list of devices that are connected to the DVR and configure the necessary settings.
Click <Device> in the menu screen.
For more information, refer to “Setting the Device”. (Page 38)
Camera
• Camera
You can configure the settings of the camera that is
connected to the DVR.
• Privacy Region
You can specify a certain area of the camera video to be
protected for your privacy.
• PTZ
You can configure the settings of the PTZ camera that is
connected to the DVR.
Set the ID and protocol.
84_ web viewer
Storage Device
You can check and change the settings of the storage device.
• Device
You will see a list of storage devices that are connected to the
DVR.
You can check the type, used/total, usage and status of the
device.
 WEB VIEWER
• HDD Alarm
You can set the alarm output channel and the alarm duration
for an error.
Remote Device
You can see a list of remote devices including PTZ cameras
and system keyboards that are connected to the RS-485 port
of the DVR and configure the necessary settings.
POS Device
You can set the channel, preset and communication port of
the POS device that is connected to the DVR.
M
 You cannot set to use the POS device remotely.
English _85
web viewer
Monitor
• Monitor
You can configure the monitoring screen settings and set the
output system.
• Spot Out
With the monitor connected via the SPOT port, if there occurs
an event such as Sensor, Motion, or Alarm, you can select a
video output mode for external monitoring.
• Mode
You can switch between live mode and play mode.
86_ web viewer
Record
For more information, refer to <Setting the Recording>. (Page 46)
Recording Schedule
If you set a recording schedule for a specific date and time,
the recording will start at that specific time.
 WEB VIEWER
- Apply to All CH : Click <Apply to All CH> to display the
confirmation window.
Event Record Duration
You can set the start and end times of recording that will be
activated if an event occurs.
English _87
web viewer
REC Quality & Resolution
• Standard/Event
You can set the resolution, frame rate and recording quality for
each channel.
Record Option
You can set the Disk End Mode.
Event
For more information, refer to <Setting the Event>. (Page 49)
Sensor Detection
You can set the sensor operation mode and the synchronized
camera as well as the alarm output type and the duration.
88_ web viewer
Motion Detection
You can set the motion detection mode and the sensitivity
as well as the alarm output type and the duration.
 WEB VIEWER
• Motion Region
Set the target motion detection area
Video Loss Detection
You can set the alarm output time if a video loss occurs.
Alarm Schedule
You can schedule the alarm output according to the day of
the week and the time.
The default setting is Event Sync, which activates the alarm
only if an event occurs.
English _89
web viewer
Network
For more information, refer to <Network Configuration>. (Page 53)
Connection
A remote user can access the DVR via the network to check
the current mode and the IP address.
• Connection
You can set the network connection route.
• Protocol
You can configure the protocol related settings.
DDNS
You can check the DDNS settings.
90_ web viewer
Live Transfer
A remote user can set the images of the DVR.
• Live Transfer
You can specify the quality of the image data that a remote
user will receive.
 WEB VIEWER
Mailing Service
You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users.
• SMTP
You can set the server that sends mails and specify if you use
the authentication process.
• Event
You can set the event interval and specify which events the
server sends mails for.
English _91
web viewer
• Group
You can add a group to receive the mail if an event occurs
and set the permission to receive the event mail for each
group.
• Recipient
You can add a user or users who will receive the mail.
ABOUT
Click <ABOUT>.
Displays the model name of connected DVR and the version
of Web Viewer.
92_ web viewer
MOBILE VIEWER
What is Mobile Viewer?
iPOLIS mobile is smartphone application that enables you to
connect to DVR (Digital Video Recorder) remotely and control
the video playback and PTZ operations (if configured) in real
time.
1.X
• Remote access via Smart phone
• Voice Recognition
• 1-split and 4-split modes supported in Live Viewer
(However, search is not available).
• Switch channels using the touch-sensitive LCD panel
• PTZ camera operations supported (complies with the
protocol of the connected DVR)
• Up to 16 channels supported
• Audio (wifi : O, 3G : X)
Compatible Smartphone
This application is optimized for
• iPhone OS v4.2.1 or later
• Android v2.1/2.2/2.3 (Galaxy S/S2 recommended)
M
 For more information, refer to the user manual.
(http://www.samsungcctv.com)
English _93
 WEB VIEWER
Key Features
backup viewer
SEC BACKUP VIEWER
You can play a file that is backed up in the format of SEC.
Backup in the format of SEC will involve in generating two files: one for the backup data and one for the viewer.
If you run the backup file viewer, the backup data file will be automatically played.
b
c
Recommended System Requirements
PCs with a lower specification than the recommended below may not fully support forward/backward and
high-speed playback.
•
•
•
•
OS : Windows XP professional, Windows Vista, Windows 7
CPU : Intel Core2-Duo 2.4GHz or higher
RAM : DDR PC-3200 1G or more
VGA : Geforce 6200 or higher
94_ backup viewer
Name
Description
/
Audio
A toggle button. Each time you press this button, the audio output will toggle
between activated and deactivated.
You can adjust the volume level from 0 to 100.
c
Screen Printout
Prints out the current screen. You should have installed the appropriate printer
driver before you can print out the screen.
File Tamper
Detection
/
A toggle button. Each time you press this button, it will toggle between activated
and deactivated. The closed lock icon indicates activation of the file tamper
detection, which will blink the screen three times and stop playing if an
unauthorized manipulation of a data file is detected.
 A message of “The file is forged” will display in the menu bar.
Deinterlace
You can enable the De-interlace function.
OSD function
Check the OSD checkbox to display the OSD information on the backup playback
screen. Information such as backup date, day of the week, time, model name,
and channel number will be displayed on the screen.
Collapses the time range that is displayed on the range bar of the storage time.
You can collapse the range bar until the overall range is shortened to 24 hours.
Zoom In/Out
Enlarges the time range that is displayed on the range bar of the storage time.
You can enlarge the range bar until the overall range is extended to 1 minute.
Display of storage time range
Displays the time range of a stored video file.
You can move the gridline of the range bar to select a time point to play.
A toggle button; each time you press this button, the "Slow Playback" icon
changes its color to display it’s activated/deactivated. If it is activated, you can use
the play speed control to adjust the play speed up to x1/16 forward and backward
respectively, whereas if deactivated, you can adjust up to x16 forward and
backward.
Speed
A toggle button; each time you press this button, the "Lock Speed" icon changes
its color to display it’s activated/deactivated.
If activated, the adjusted speed will be kept even if you release the mouse on the
speed bar. If deactivated, the adjusted speed will be applied only while you use
the mouse to hold the adjusted speed, and if you release the mouse, the speed
will restore to x1.
You can adjust the play speed up to x16 forward and backward respectively,
which varies according to the frame rate per second of the source.
Fast playback maximum is limited to x2 for footages recorded at 20 ~ 30 fps
(frames per second), x4 for 11 ~ 19 fps, x8 for 6 ~ 10 fps, and x16 for footages
recorded at slower than 6 fps.
Displays the next frame. This is available only if the playback is stopped.
Play
A toggle button. Press it once to start playing the video and switch the button
mode to 'Pause', and press it again to switch the button mode to Play and stop
playing temporarily.
Displays the previous frame. This is available only if the playback is stopped.
English _95
 BACKUP VIEWER
b
Saves the current screen as an image file. Supported file formats include BMP
and JPEG.
appendix
PRODUCT SPECIFICATION
Details
Item
SRD-1640
Inputs
16 composite video 0.5–1 Vpp, 75 ohm
Resolution
704x480 NTSC, 704x576 PAL
Frame rate
480fps NTSC, 400fps PAL
Resolution
704x480 NTSC, 704x576 PAL
Multi Screen display
1/4/6/8/9/13/16/SEQUENCE/PIP
Embedded
Linux
Compression
H.264
Record Rate
NTSC: Up to 120fps @ 704x480
PAL: Up to 100fps @ 704x576
NTSC: Up to 240fps @ 704x240
PAL: Up to 200fps @ 704x288
NTSC: Up to 480fps @ 352x240
PAL: Up to 400fps @ 352x288
SRD-840
8 composite video 0.5–1 Vpp, 75 ohm
Video
Live
240fps NTSC, 200fps PAL
1/4/6/8/9/SEQUENCE/PIP
Performance
OS
Recording
NTSC: Up to 60fps @ 704x480
PAL: Up to 50fps @ 704x576
NTSC: Up to 120fps @ 704x240
PAL: Up to 100fps @ 704x288
NTSC: Up to 240fps @ 352x240
PAL: Up to 200fps @ 352x288
NTSC : Manual, Schedule (Continuous/Event), Event(Pre/Post)
Mode
PAL: Manual, Schedule (Continuous/Event), Event(Pre/Post)
Overwrite modes
Continuous
Pre-alarm
Up to 5sec
Post-Alarm
Up to 6 hour. (5, 10, 20, 30 sec, 1, 3, 5, 10, 20 min, 1, 2, 3, 4, 5, 6 hour)
Search mode
Date/time, Event, Back up, POS, Motion
Playback function
Fast Forward / Backward, Slow Forward / Backward, Step Forward / Backward
Transmission speed
CIF, 100/120fps
Bandwidth
Up to (4)Mbps, Unlimited(4M)/2/1.5/1 Mbps/800/600/500/400/300/200/100/50 kbps
Bandwidth control
Automatic
Stream
CIF (H.264)
Search mode
Network
Remote users Maximum 4 Persons (Search up to (2), Live Unicast/Live Multicast available)
96_ appendix
Protocol support
TCP/IP, DHCP, PPPoE, SMTP, NTP, HTTP, DDNS, RTP, RTSP
Monitoring
Webviewer, CMS (Smart Viewer, NET-i)
Details
Item
SRD-1640
SRD-840
Smart phone
Android, i-phone (iPad included)
Protocol support
RTP, RTSP, HTTP, CGI
Transmission speed
CIF Max 15fps(Single Channel)/ CIF Max 2fps(Quad Channel)
Smart phone
 APPENDIX
Remote users Maximum Live(1)
Storage
Internal HDD
Up to 1 SATA HDDs
External HDD
–
DVD Writer (Back-up)
–
USB (Back-up)
2 USB Ports
File Format (Back-up)
BU(DVR Player), EXE(Include Player)
Password Protection
1 Admin, 10 Group , 10 User per 1 Group
Data Authentication
Watermark
VGA
1 VGA (1024x768) ※ Main Composite Selectable
HDMI
–
Main/Spot Composite
1 BNC (1 Vp-p, 75 ohm)/Analog Spot (1 BNC, 1 Vp-p, 75 ohm) Selectable
Spot Composite
Analog Spot (1 BNC, 1 Vp-p, 75 ohm)
Loop Outputs
–
Inputs / Output
4 line in / 1 line out
Compression
G.711
Sampling rate
8KHz
Inputs / Outputs
Terminal (16)8 inputs (NO/NC) / Terminal 2 relay outputs,
Rating : 24VDC/1A, 125V AC/0.5A
Remote notification
Notification via e-mail
Ethernet
1 RJ45 10/100 Base-T
Serial interface
RS-485(Half) for PTZ, System Keyboard ※ Support for POS Interface (VSI-Pro)
USB
USB 2.0, 2 ports (Front)
e-SATA
–
Application Supoort
Mouse, Remote Controller
PTZ Protocol support
Samsung-E / Samsung-T / Pelco-D / Pelco-p / Panasonic / Phillips / AD / DIAMOND /
ERNA / GE / VCL TP / VICON / ELMO
Security
Interface
Monitors
Audio
Alarm
Connections
English _97
appendix
Details
Item
SRD-1640
SRD-840
General
Input Voltage /Current
DC12V Adaptor,4A,100~250VAC, 50~60Hz, 48watt
Power consumption
Max.36 W (with 1x HDD)
Operating Temperature
/Humidity
+0°C to +40°C (+32°F to +104°F)/ 20%RH to 85%RH
Electrical
Environmental
Dimension (W x H x D) W360 x H44 x D160 mm (14.17 x 1.73 x 6.30 inches)
Mechanical
Weight (With hard disks) 1.72Kg
Rack mount kit
Lauguage
1.68Kg
–
Korean, Japanese, Chinese, English, French, German, Spanish, Italian, Russian, Polish,
Czech, Turkish, Netherlands, Portuguese, Swedish, Danish, Thailandais, Rumania,
Serbia, Croatia, Hungary, Greek (22 Language)
 This product complies with the industrial appliance noise standards. Separate soundproof equipment is recommended if you want
to install it indoors.
98_ appendix
English _99
360 (14.17")
44 (1.73")
48.7(1.92")
171.3 (6.74")
159.93 (6.30")
 APPENDIX
CH4
CH3
CH2
CH1
VIDEO IN
1
AUDIO IN
2
3
4
DC 12 V
SPOT
1
AUDIO OUT
COM COM
2
ALARM
OUT
VIDEO IN
RS485
VGA OUT
1 2 3 4 5 6 7 8 G
ALARM IN
SERIAL
5
6
7
8
VIDEO OUT
CONSOLE
NETWORK
unit : mm (inches)
❖ SRD-840
PRODUCT OVERVIEW
100_ appendix
360 (14.17")
44 (1.73")
48.7(1.92")
171.3 (6.74")
159.93 (6.30")
CH4
CH3
CH2
CH1
VIDEO IN
1
2
3
4
5
6
7
DC 12 V
8
SPOT
1
AUDIO IN
AUDIO OUT
COM COM
2
ALARM
OUT
VIDEO IN
RS485
VGA OUT
1 2 3 4 5 6 7 8 G 9 10 11 12 13 14
ALARM IN
15 16 G
SERIAL
9
10
11
12
13
14
15
VIDEO OUT
16
CONSOLE
NETWORK
unit : mm (inches)
❖ SRD-1640
appendix
DEFAULT SETTING
This returns the factory default settings.
The settings are made as follows;
• Use System/Load Factory Default in MENU
 The default settings are based on SRD-1640.
 The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
Details
Date/Time/Language
Factory Default
Date
YYYY-MM-DD
Time Format
24 hours
Time Zone
GMT
Time Synchronize
OFF
DST
OFF
Language
English
ID
admin
New Password
4321
Restricted Access
Backup/Record Lock/
Search/PTZ/Remote
Alarm Out/Shutdown
Auto Logout
OFF
Broadcast Format
NTSC/PAL
Video
ON
Audio
OFF
CH Name
CAM 01 ~ CAM 16
SEQ-Dwell Time
5sec
ID
Camera No.
Protocol
None
Brightness
50
Contrast
50
Color
50
Check Alarm Output Port
OFF
Duration
OFF
Replace Alarm Output Port
OFF
Duration
OFF
Date/Time/Language
System Settings
Admin
Permission
Management
Setting
System Management
System Information
Camera
Camera
PTZ
Device
Screen Setup
Storage Device
HDD Alarm
English _101
 APPENDIX
Category
appendix
Category
Details
Remote Device
Factory Default
Baudrate
9600
Parity
None
Data
8
Stop bit
1
Transfer Type
Half Duplex
System Keyboard
OFF
Remote Control
ON(00)
POS Device
OFF
Device
Monitor
Monitor
Event Display
OFF
Display
All
Multi CH SEQ Time
5 sec
Video Output
Auto
Display Position Setup
30
Spot Out 1
CH1 ~ CH16
Event Display
OFF
Live Mode
ALL
Play Mode
ALL
Spot Out
Mode
Recording Schedule
Event Record Duration
Channel 1
Event
PRE Event
OFF
POST Event
1 min
Normal Recording
Recording
REC Quality/Resolution
Event
Record Option
CIF(S)
Frame Rate
7 fps
Record Quality
Level 4
Resolution
4CIF(L)
Frame Rate
7 fps
Record Quality
Level 4
Setup
Overwrite
Disk End Beep
OFF
Disk End Mode
Auto Delete
102_ appendix
Resolution
OFF
Category
Details
Sensor Detection
Motion Detection
Video Loss Detection
Alarm Schedule
Sensor Operation
OFF
Camera
Camera No.
Alarm
None
Duration
10 sec
Mode
OFF
Sensitivity
Level10(high)
Alarm
None
Duration
10 sec
Motion Region
All Area
Video Loss State
OFF
Alarm
None
Duration
10 sec
Alarm1
Event Sync
Connection
Connection Mode
Protocol
DDNS
Network
Connection Mode
Static IP
Bandwidth
2Mbps
IP
192.168.1.200
Gateway
192.168.1.1
Subnet Mask
255.255.255.0
DNS
168.126.63.1
Protocol Type
TCP
Port (TCP)
4520~4524
Webviewer Port
80
DDNS Site
OFF
Resolution
CIF(S)
Quality
Low
Live Transfer
SMTP
Mailing Service
Event
Group
Server
OFF
Port
25
Use Authentication
OFF
Secure Transfer
Never
Event Interval
10 min
Use Event Transfer
OFF
Group
OFF
Recipient Permission
OFF
English _103
 APPENDIX
Event
Factory Default
appendix
TROUBLESHOOTING
Symptom
Countermeasures
The system does not turn on and the indicator on the
front panel does not work at all.
 Check if the power supply system is properly connected.
 Check the system for the input voltage from the power source.
 If the problem persists even after you have taken the above actions,
check the power supplier and replace it with a new one if neccessary.
Some channels display just a black screen even if they
receive video sources.
 Check if the camera connected to the system properly displays the
image. Sometimes, this problem may occur on a camera that is not
properly connected to the video source.
 Check if the camera is properly supplied with power.
 Sometimes, this problem may occur on a channel with weak video
signal from a video distributor that is connected to multiple systems. In
this case, input the video source of the camera directly into the DVR.
This may find the cause and solve the problem.
If I press the [REC] button on the remote control, the
REC indicator does not flash, nor the player start
recording.
 Check if there is a free space on the HDD for the recording.
 Check if the record mode is set to ON in the record mode setting.
The screen displays the logo image repeatedly.
 This may occur from a problem with the main board, or the related
software is corrupt.
Contact the nearest service center for more information.
The Channel button does not work on the Live screen.
 The Channel button does not work if the current screen is in the event
monitoring mode.
In the event monitoring screen, press the [ALARM] button to exit the
screen and select a channel.
The cursor will not move to the Start button when I start
the calendar search.
 Check if the channel and the date that you want to play are marked
with the V symbol.
Both channel and date should be checked before you can start playing
with the Start button.
When the alarm sounds, I press the [ALARM] button
to release the alarm but it does not work.
 Press the [MENU] button to release the alarm in the following way:
1) To release the event monitoring mode : Monitoring Mode – set the
duration of the event monitoring to Off.
2) To release the alarm sound : Event Record Mode - Alarm (Motion
Detection/Video Loss) – deactivate the alarm sound.
3) To release the event : Event Record Mode - Alarm (Motion Detection/
Video Loss) – set the mode to Off.
No response is made even if I press the [PTZ] button on
the Live screen.
 Menu ¬ Camera ¬ Check if the current protocols and other settings
in the PTZ device are properly configured according to the PTZ camera.
104_ appendix
Symptom
Countermeasures
 It takes time for the DVR to recognize multiple external HDDs. Try again
in a moment and if the problem (of failure to recognize as many HDDs
as connected) persists, it may occur due to a mechanical error of the
HDD installed. Try again with a different HDD.
A message of “Need to reset date/time.” Is displayed on
the screen.
 This message is displayed if there occurs a problem with the time
setting of the internal clock or an error in the clock itself.
Contact the retailer or the service center for more information.
The time bar is not displayed in Search mode.
 The timeline can switch between normal and extension mode.
In extension mode, the time bar may not be displayed in the current
timeline. Switch to normal mode or use the left or right button to
navigate through the time bar.
The “NO HDD” icon and an error message are
displayed.
 Check the HDD for connection. If the problem persists in a normal
condition, contact the nearest service center to have the HDD checked
by the service personnel.
I have connected an external storage device (external
SATA HDD) to the DVR but the DVR seems not to
recognize it.
 See the compatibility list of external storage devices to check if the
connected device is supported by the DVR.
For the compatibility list, contact the retailer where you purchased the
DVR.
If I press the ESC key in full screen mode of the
WebViewer, the system does not switch to a normal
split mode.
 Press the ALT+TAB keys to select ‘ACTIVE MOVIE’ and press the ESC
key again. The system will switch to a normal split mode.
I found it difficult to configure the network settings if
using the default search, backup and router settings.
 For more information, refer to the user manual.
 If you want to check the basics of the product for a quick start, refer to
the quick start guide (backup, search).
I forgot the password.
 Contact the DVR administrator for help.
Backup data is just not played by the PC or DVR.
 When you are backing up data, you have choices about the player
either: PC or DVR. Make your selection before proceeding.
 If you are using the PC to play the data, the format of the backup file
should be SEC.
 If you are using the DVR for this purpose, formatting backup files should
be done by the DVR.
My player does not switch to Live mode while in
playback.
 Press the Stop [@] button on the remote control, or click the [
icon on the launcher to switch to Live mode.
 APPENDIX
I've found that the DVR does not recognize as many
disks as installed when I have connected multiple
external HDDs to the DVR.
]
English _105
appendix
Symptom
Countermeasures
Recording does not work.
 If your player does not display a Live image at all, that indicates
recording does not work so first check if you see an image on the
screen.
 Recording does not work if the recording settings are not properly
configured.
1) Manual Record: Press the [REC] button on the remote control to start
recording.
2) Scheduled Record: Specify a desired time in Menu – Record - Recording
Schedule. Recording will start at the specified time.
- <Continuous> Record: Recording will proceed in any conditions at
the specified time.
- <Event> Record: When an event occurs, recording will perform only if
the event is of alarm, motion detection and video loss.
If there is no event found, recording will not perform.
- <Continuous / Event> Record: If there is no event found, Continuous
recording will perform. Whereas, if an event occurs, Event recording
will perform.
The image quality of the recording data is not good.
 Increase the resolution and quality level in Menu – Record – Quality /
Resolution.
1) Resolution: Select a bigger size when specifying the recording size.
(4CIF> 2CIF>CIF)
The recording image in the CIF format shows a deteriorated quality as it
is enlarged from a small-sized image.
2) Record Quality: Specify a bigger level for the recording quality.
 If you increase the resolution and the recording quality, the data size
increases accordingly. So the HDD will be filled faster. Overwriting will
overwrite the existing data so recording will proceed at a shorter
interval.
106_ appendix
OPEN SOURCE LICENSE REPORT ON THE PRODUCT
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete
Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source
distribution might be charged.
• GPL Software : linux kernel, Sysvinit, dosfstools, wget, msmtp, busybox, cdrtools, dvd+rw-tools, iconv, smartctl, uboot, minicom, openssl, bash,
lm_sensors
• LGPL Software : glibc, vmstat, inetutils
• OpenSSL License : OpenSSL
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom
to share and change it. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change free software
to make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s software and
to any other program whose authors commit to using it. (Some other
Free Software Foundation software is covered by the GNU Lesser
General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are designed to make sure that you have
the freedom to distribute copies of free software (and charge for this
service if you wish), that you receive source code or can get it if you
want it, that you can change the software or use pieces of it in new free
programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone
to deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute
copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis
or for a fee, you must give the recipients all the rights that you have. You
must make sure that they, too, receive or can get the source code. And
you must show them these terms so they know their rights.
We protect your rights with two steps:
(1) copyright the software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain
that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on,
we want its recipients to know that what they have is not the original, so
that any problems introduced by others will not reflect on the original
authors’ reputations.
Finally, any free program is threatened constantly by software patents.
We wish to avoid the danger that redistributors of a free program will
individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent must
be licensed for everyone’s free use or not licensed at all. The precise
terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin S
0. This License applies to any program or other work which contains a
notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The “Program”, below, refers
to any such program or work, and a “work based on the Program”
means either the Program or any derivative work under copyright law:
that is to say, a work containing the Program or a portion of it, either
verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term
“modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of running
the Program is not restricted, and the output from the Program is
covered only if its contents constitute a work based on the Program
(independent of having been made by running the Program). Whether
that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s
source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices
that refer to this License and to the absence of any warranty; and give
any other recipients of the Program a copy of this License along with
the Program.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of
it, thus forming a work based on the Program, and copy and distribute
such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices
stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in
whole or in part contains or is derived from the Program or any
part thereof, to be licensed as a whole at no charge to all third
parties under the terms of this License.
c) If the modified program normally reads commands interactively
when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide a
warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this
License. (Exception: if the Program itself is interactive but does
not normally print such an announcement, your work based on
the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves,
then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the
same sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms of this
License, whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise the
right to control the distribution of derivative or collective works based on
the Program.
In addition, mere aggregation of another work not based on the
Program with the Program (or with a work based on the Program) on a
volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it,
under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the
terms of Sections 1 and 2 above on a medium customarily used
for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to
give any third party, for a charge no more than your cost of
physically performing source distribution, a complete machinereadable copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to
distribute corresponding source code. (This alternative is allowed
only for noncommercial distribution and only if you received the
program in object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special
exception, the source code distributed need not include anything that is
normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on
which the executable runs, unless that component itself accompanies
the executable.
If distribution of executable or object code is made by offering access to
copy from a designated place, then offering equivalent access to copy
the source code from the same place counts as distribution of the
source code, even though third parties are not compelled to copy the
source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this License. Any attempt otherwise
to copy, modify, sublicense or distribute the Program is void, and will
automatically terminate your rights under this License. However, parties
who have received copies, or rights, from you under this License will not
have their licenses terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify or
distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by
modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and all
its terms and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these
terms and conditions. You may not impose any further restrictions on
the recipients’ exercise of the rights granted herein. You are not
responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute
so as to satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not
permit royalty-free redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely from
distribution of the Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply
and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents
or other property right claims or to contest validity of any such claims;
this section has the sole purpose of protecting the integrity of the free
software distribution system, which is implemented by public license
practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on
consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be
a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add
an explicit geographical distribution limitation excluding those countries,
so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if
written in the body of this License.
9. The Free Software Foundation may publish revised and/or new
versions of the General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and “any
later version”, you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number
of this License, you may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the author
to ask for permission. For software which is copyrighted by the Free
Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by the
two goals of preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New
Programs
If you develop a new program, and you want it to be of the greatest
possible use to the public, the best way to achieve this is to make it free
software which everyone can redistribute and change under these
terms.
To do so, attach the following notices to the program. It is safest to
attach them to the start of each source file to most effectively convey
the exclusion of warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is found.
one line to give the program’s name and an idea of what it does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 2 of the License, or (at your
option) any later version.
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
the GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software Foundation,
Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
Also add information on how to contact you by electronic and paper
mail. If the program is interactive, make it output a short notice like this
when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details
type ‘show w’. This is free software, and you are welcome to
redistribute it under certain conditions; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the
appropriate parts of the General Public License. Of course, the
commands you use may be called something other than ‘show w’ and
‘show c’; they could even be mouse-clicks or menu items--whatever
suits your program.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
‘Gnomovision’ (which makes passes at compilers) written by James
Hacker.
signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This
General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may
consider it more useful to permit linking proprietary applications with the
library. If this is what you want to do, use the GNU Lesser General
Public License instead of this License.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software
and other kinds of works.
The licenses for most software and other practical works are designed
to take away your freedom to share and change the works. By contrast,
the GNU General Public License is intended to guarantee your freedom
to share and change all versions of a program--to make sure it remains
free software for all its users. We, the Free Software Foundation, use the
GNU General Public License for most of our software; it applies also to
any other work released this way by its authors. You can apply it to your
programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are designed to make sure that you have
the freedom to distribute copies of free software (and charge for them if
you wish), that you receive source code or can get it if you want it, that
you can change the software or use pieces of it in new free programs,
and that you know you can do these things.
A “covered work” means either the unmodified Program or a work
based on the Program.
To “propagate” a work means to do anything with it that, without
permission, would make you directly or secondarily liable for
infringement under applicable copyright law, except executing it on a
computer or modifying a private copy. Propagation includes copying,
distribution (with or without modification), making available to the public,
and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other
parties to make or receive copies. Mere interaction with a user through
a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the
extent that it includes a convenient and prominently visible feature that
(1) displays an appropriate copyright notice, and (2) tells the user that
there is no warranty for the work (except to the extent that warranties
are provided), that licensees may convey the work under this License,
and how to view a copy of this License. If the interface presents a list of
user commands or options, such as a menu, a prominent item in the list
meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for
making modifications to it. “Object code” means any non-source form
of a work.
To protect your rights, we need to prevent others from denying you
these rights or asking you to surrender the rights. Therefore, you have
certain responsibilities if you distribute copies of the software, or if you
modify it: responsibilities to respect the freedom of others.
A “Standard Interface” means an interface that either is an official
standard defined by a recognized standards body, or, in the case of
interfaces specified for a particular programming language, one that is
widely used among developers working in that language.
For example, if you distribute copies of such a program, whether gratis
or for a fee, you must pass on to the recipients the same freedoms that
you received. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know their
rights.
The “System Libraries” of an executable work include anything, other
than the work as a whole, that (a) is included in the normal form of
packaging a Major Component, but which is not part of that Major
Component, and (b) serves only to enable use of the work with that
Major Component, or to implement a Standard Interface for which an
implementation is available to the public in source code form. A “Major
Component”, in this context, means a major essential component
(kernel, window system, and so on) of the specific operating system (if
any) on which the executable work runs, or a compiler used to produce
the work, or an object code interpreter used to run it.
Developers that use the GNU GPL protect your rights with two steps:
(1) assert copyright on the software, and (2) offer you this License giving
you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains
that there is no warranty for this free software. For both users’ and
authors’ sake, the GPL requires that modified versions be marked as
changed, so that their problems will not be attributed erroneously to
authors of previous versions.
Some devices are designed to deny users access to install or run
modified versions of the software inside them, although the
manufacturer can do so. This is fundamentally incompatible with the
aim of protecting users’ freedom to change the software. The
systematic pattern of such abuse occurs in the area of products for
individuals to use, which is precisely where it is most unacceptable.
Therefore, we have designed this version of the GPL to prohibit the
practice for those products. If such problems arise substantially in other
domains, we stand ready to extend this provision to those domains in
future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents.
States should not allow patents to restrict development and use of
software on general-purpose computers, but in those that do, we wish
to avoid the special danger that patents applied to a free program could
make it effectively proprietary. To prevent this, the GPL assures that
patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and
modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of
works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this
License. Each licensee is addressed as “you”. “Licensees” and
“recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work
in a fashion requiring copyright permission, other than the making of an
exact copy. The resulting work is called a “modified version” of the
earlier work or a work “based on” the earlier work.
The “Corresponding Source” for a work in object code form means all
the source code needed to generate, install, and (for an executable
work) run the object code and to modify the work, including scripts to
control those activities. However, it does not include the work’s System
Libraries, or general-purpose tools or generally available free programs
which are used unmodified in performing those activities but which are
not part of the work. For example, Corresponding Source includes
interface definition files associated with source files for the work, and the
source code for shared libraries and dynamically linked subprograms
that the work is specifically designed to require, such as by intimate
data communication or control flow between those subprograms and
other parts of the work.
The Corresponding Source need not include anything that users can
regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same
work.
2. Basic Permissions.
All rights granted under this License are granted for the term of
copyright on the Program, and are irrevocable provided the stated
conditions are met. This License explicitly affirms your unlimited
permission to run the unmodified Program. The output from running a
covered work is covered by this License only if the output, given its
content, constitutes a covered work. This License acknowledges your
rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not
convey, without conditions so long as your license otherwise remains in
force. You may convey covered works to others for the sole purpose of
having them make modifications exclusively for you, or provide you with
facilities for running those works, provided that you comply with the
terms of this License in conveying all material for which you do not
control copyright. Those thus making or running the covered works for
you must do so exclusively on your behalf, under your direction and
control, on terms that prohibit them from making any copies of your
copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the
conditions stated below. Sublicensing is not allowed; section 10 makes
it unnecessary.
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological
measure under any applicable law fulfilling obligations under article 11 of
the WIPO copyright treaty adopted on 20 December 1996, or similar
laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid
circumvention of technological measures to the extent such
circumvention is effected by exercising rights under this License with
respect to the covered work, and you disclaim any intention to limit
operation or modification of the work as a means of enforcing, against
the work’s users, your or third parties’ legal rights to forbid
circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you
receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice;
keep intact all notices stating that this License and any non-permissive
terms added in accord with section 7 apply to the code; keep intact all
notices of the absence of any warranty; and give all recipients a copy of
this License along with the Program.
You may charge any price or no price for each copy that you convey,
and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to
produce it from the Program, in the form of source code under the
terms of section 4, provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified
it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released
under this License and any conditions added under section 7.
This requirement modifies the requirement in section 4 to “keep
intact all notices”.
c) You must license the entire work, as a whole, under this License
to anyone who comes into possession of a copy. This License
will therefore apply, along with any applicable section 7 additional
terms, to the whole of the work, and all its parts, regardless of
how they are packaged. This License gives no permission to
license the work in any other way, but it does not invalidate such
permission if you have separately received it.
d) If the work has interactive user interfaces, each must display
Appropriate Legal Notices; however, if the Program has
interactive interfaces that do not display Appropriate Legal
Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent
works, which are not by their nature extensions of the covered work,
and which are not combined with it such as to form a larger program, in
or on a volume of a storage or distribution medium, is called an
“aggregate” if the compilation and its resulting copyright are not used to
limit the access or legal rights of the compilation’s users beyond what
the individual works permit. Inclusion of a covered work in an aggregate
does not cause this License to apply to the other parts of the
aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of
sections 4 and 5, provided that you also convey the machine-readable
Corresponding Source under the terms of this License, in one of these
ways:
a) Convey the object code in, or embodied in, a physical product
(including a physical distribution medium), accompanied by the
Corresponding Source fixed on a durable physical medium
customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product
(including a physical distribution medium), accompanied by a
written offer, valid for at least three years and valid for as long as
you offer spare parts or customer support for that product
model, to give anyone who possesses the object code either (1)
a copy of the Corresponding Source for all the software in the
product that is covered by this License, on a durable physical
medium customarily used for software interchange, for a price
no more than your reasonable cost of physically performing this
conveying of source, or (2) access to copy the Corresponding
Source from a network server at no charge.
c) Convey individual copies of the object code with a copy of the
written offer to provide the Corresponding Source. This
alternative is allowed only occasionally and noncommercially, and
only if you received the object code with such an offer, in accord
with subsection 6b.
d) Convey the object code by offering access from a designated
place (gratis or for a charge), and offer equivalent access to the
Corresponding Source in the same way through the same place
at no further charge. You need not require recipients to copy the
Corresponding Source along with the object code. If the place to
copy the object code is a network server, the Corresponding
Source may be on a different server (operated by you or a third
party) that supports equivalent copying facilities, provided you
maintain clear directions next to the object code saying where to
find the Corresponding Source. Regardless of what server hosts
the Corresponding Source, you remain obligated to ensure that it
is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission,
provided you inform other peers where the object code and
Corresponding Source of the work are being offered to the
general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded
from the Corresponding Source as a System Library, need not be
included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any
tangible personal property which is normally used for personal, family, or
household purposes, or (2) anything designed or sold for incorporation
into a dwelling. In determining whether a product is a consumer
product, doubtful cases shall be resolved in favor of coverage. For a
particular product received by a particular user, “normally used” refers to
a typical or common use of that class of product, regardless of the
status of the particular user or of the way in which the particular user
actually uses, or expects or is expected to use, the product. A product
is a consumer product regardless of whether the product has
substantial commercial, industrial or non-consumer uses, unless such
uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods,
procedures, authorization keys, or other information required to install
and execute modified versions of a covered work in that User Product
from a modified version of its Corresponding Source. The information
must suffice to ensure that the continued functioning of the modified
object code is in no case prevented or interfered with solely because
modification has been made.
If you convey an object code work under this section in, or with, or
specifically for use in, a User Product, and the conveying occurs as part
of a transaction in which the right of possession and use of the User
Product is transferred to the recipient in perpetuity or for a fixed term
(regardless of how the transaction is characterized), the Corresponding
Source conveyed under this section must be accompanied by the
Installation Information. But this requirement does not apply if neither
you nor any third party retains the ability to install modified object code
on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a
requirement to continue to provide support service, warranty, or
updates for a work that has been modified or installed by the recipient,
or for the User Product in which it has been modified or installed.
Access to a network may be denied when the modification itself
materially and adversely affects the operation of the network or violates
the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided,
in accord with this section must be in a format that is publicly
documented (and with an implementation available to the public in
source code form), and must require no special password or key for
unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this
License by making exceptions from one or more of its conditions.
Additional permissions that are applicable to the entire Program shall be
treated as though they were included in this License, to the extent that
they are valid under applicable law. If additional permissions apply only
to part of the Program, that part may be used separately under those
permissions, but the entire Program remains governed by this License
without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option
remove any additional permissions from that copy, or from any part of it.
(Additional permissions may be written to require their own removal in
certain cases when you modify the work.) You may place additional
permissions on material, added by you to a covered work, for which
you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add
to a covered work, you may (if authorized by the copyright holders of
that material) supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms
of sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal notices or
author attributions in that material or in the Appropriate Legal
Notices displayed by works containing it; or
c) Prohibiting misrepresentation of the origin of that material, or
requiring that modified versions of such material be marked in
reasonable ways as different from the original version; or
d) Limiting the use for publicity purposes of names of licensors or
authors of the material; or
e) Declining to grant rights under trademark law for use of some
trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of that
material by anyone who conveys the material (or modified
versions of it) with contractual assumptions of liability to the
recipient, for any liability that these contractual assumptions
directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further
restrictions” within the meaning of section 10. If the Program as you
received it, or any part of it, contains a notice stating that it is governed
by this License along with a term that is a further restriction, you may
remove that term. If a license document contains a further restriction but
permits relicensing or conveying under this License, you may add to a
covered work material governed by the terms of that license document,
provided that the further restriction does not survive such relicensing or
conveying.
If you add terms to a covered work in accord with this section, you
must place, in the relevant source files, a statement of the additional
terms that apply to those files, or a notice indicating where to find the
applicable terms.
Additional terms, permissive or non-permissive, may be stated in the
form of a separately written license, or stated as exceptions; the above
requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly
provided under this License. Any attempt otherwise to propagate or
modify it is void, and will automatically terminate your rights under this
License (including any patent licenses granted under the third paragraph
of section 11).
However, if you cease all violation of this License, then your license from
a particular copyright holder is reinstated (a) provisionally, unless and
until the copyright holder explicitly and finally terminates your license,
and (b) permanently, if the copyright holder fails to notify you of the
violation by some reasonable means prior to 60 days after the
cessation.
Moreover, your license from a particular copyright holder is reinstated
permanently if the copyright holder notifies you of the violation by some
reasonable means, this is the first time you have received notice of
violation of this License (for any work) from that copyright holder, and
you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the
licenses of parties who have received copies or rights from you under
this License. If your rights have been terminated and not permanently
reinstated, you do not qualify to receive new licenses for the same
material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a
copy of the Program. Ancillary propagation of a covered work occurring
solely as a consequence of using peer-to-peer transmission to receive a
copy likewise does not require acceptance. However, nothing other
than this License grants you permission to propagate or modify any
covered work. These actions infringe copyright if you do not accept this
License. Therefore, by modifying or propagating a covered work, you
indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically
receives a license from the original licensors, to run, modify and
propagate that work, subject to this License. You are not responsible for
enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an
organization, or substantially all assets of one, or subdividing an
organization, or merging organizations. If propagation of a covered work
results from an entity transaction, each party to that transaction who
receives a copy of the work also receives whatever licenses to the work
the party’s predecessor in interest had or could give under the previous
paragraph, plus a right to possession of the Corresponding Source of
the work from the predecessor in interest, if the predecessor has it or
can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights
granted or affirmed under this License. For example, you may not
impose a license fee, royalty, or other charge for exercise of rights
granted under this License, and you may not initiate litigation (including
a cross-claim or counterclaim in a lawsuit) alleging that any patent claim
is infringed by making, using, selling, offering for sale, or importing the
Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this
License of the Program or a work on which the Program is based. The
work thus licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or
controlled by the contributor, whether already acquired or hereafter
acquired, that would be infringed by some manner, permitted by this
License, of making, using, or selling its contributor version, but do not
include claims that would be infringed only as a consequence of further
modification of the contributor version. For purposes of this definition,
“control” includes the right to grant patent sublicenses in a manner
consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free
patent license under the contributor’s essential patent claims, to make,
use, sell, offer for sale, import and otherwise run, modify and propagate
the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express
agreement or commitment, however denominated, not to enforce a
patent (such as an express permission to practice a patent or covenant
not to sue for patent infringement). To “grant” such a patent license to a
party means to make such an agreement or commitment not to enforce
a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and
the Corresponding Source of the work is not available for anyone to copy,
free of charge and under the terms of this License, through a publicly
available network server or other readily accessible means, then you must
either (1) cause the Corresponding Source to be so available, or (2)
arrange to deprive yourself of the benefit of the patent license for this
particular work, or (3) arrange, in a manner consistent with the
requirements of this License, to extend the patent license to downstream
recipients. “Knowingly relying” means you have actual knowledge that, but
for the patent license, your conveying the covered work in a country, or
your recipient’s use of the covered work in a country, would infringe one or
more identifiable patents in that country that you have reason to believe
are valid.
If, pursuant to or in connection with a single transaction or arrangement,
you convey, or propagate by procuring conveyance of, a covered work,
and grant a patent license to some of the parties receiving the covered
work authorizing them to use, propagate, modify or convey a specific
copy of the covered work, then the patent license you grant is
automatically extended to all recipients of the covered work and works
based on it.
A patent license is “discriminatory” if it does not include within the scope
of its coverage, prohibits the exercise of, or is conditioned on the
non-exercise of one or more of the rights that are specifically granted
under this License. You may not convey a covered work if you are a
party to an arrangement with a third party that is in the business of
distributing software, under which you make payment to the third party
based on the extent of your activity of conveying the work, and under
which the third party grants, to any of the parties who would receive the
covered work from you, a discriminatory patent license (a) in connection
with copies of the covered work conveyed by you (or copies made from
those copies), or (b) primarily for and in connection with specific
products or compilations that contain the covered work, unless you
entered into that arrangement, or that patent license was granted, prior
to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any
implied license or other defenses to infringement that may otherwise be
available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot convey a
covered work so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you
may not convey it at all. For example, if you agree to terms that obligate
you to collect a royalty for further conveying from those to whom you
convey the Program, the only way you could satisfy both those terms
and this License would be to refrain entirely from conveying the
Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have
permission to link or combine any covered work with a work licensed
under version 3 of the GNU Affero General Public License into a single
combined work, and to convey the resulting work. The terms of this
License will continue to apply to the part which is the covered work, but
the special requirements of the GNU Affero General Public License,
section 13, concerning interaction through a network will apply to the
combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions
of the GNU General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies that a certain numbered version of the GNU General Public
License “or any later version” applies to it, you have the option of
following the terms and conditions either of that numbered version or of
any later version published by the Free Software Foundation. If the
Program does not specify a version number of the GNU General Public
License, you may choose any version ever published by the Free
Software Foundation.
If the Program specifies that a proxy can decide which future versions of
the GNU General Public License can be used, that proxy’s public
statement of acceptance of a version permanently authorizes you to
choose that version for the Program.
Later license versions may give you additional or different permissions.
However, no additional obligations are imposed on any author or
copyright holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above
cannot be given local legal effect according to their terms, reviewing
courts shall apply local law that most closely approximates an absolute
waiver of all civil liability in connection with the Program, unless a
warranty or assumption of liability accompanies a copy of the Program
in return for a fee.
END OF TERMS AND CONDITIONS
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL.
It also counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom
to share and change it. By contrast, the GNU General Public Licenses
are intended to guarantee your freedom to share and change free
software to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some
specially designated software packages--typically libraries--of the Free
Software Foundation and other authors who decide to use it. You can
use it too, but we suggest you first think carefully about whether this
license or the ordinary General Public License is the better strategy to
use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not
price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for
this service if you wish); that you receive source code or can get it if you
want it; that you can change the software and use pieces of it in new
free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid
distributors to deny you these rights or to ask you to surrender these
rights. These restrictions translate to certain responsibilities for you if you
distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a
fee, you must give the recipients all the rights that we gave you. You
must make sure that they, too, receive or can get the source code. If
you link other code with the library, you must provide complete object
files to the recipients, so that they can relink them with the library after
making changes to the library and recompiling it. And you must show
them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the
library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no
warranty for the free library. Also, if the library is modified by someone
else and passed on, the recipients should know that what they have is
not the original version, so that the original author’s reputation will not be
affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any
free program. We wish to make sure that a company cannot effectively
restrict the users of a free program by obtaining a restrictive license from
a patent holder. Therefore, we insist that any patent license obtained for
a version of the library must be consistent with the full freedom of use
specified in this license.
Most GNU software, including some libraries, is covered by the ordinary
GNU General Public License. This license, the GNU Lesser General
Public License, applies to certain designated libraries, and is quite
different from the ordinary General Public License. We use this license
for certain libraries in order to permit linking those libraries into non-free
programs.
When a program is linked with a library, whether statically or using a
shared library, the combination of the two is legally speaking a
combined work, a derivative of the original library. The ordinary General
Public License therefore permits such linking only if the entire
combination fits its criteria of freedom. The Lesser General Public
License permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does
Less to protect the user’s freedom than the ordinary General Public
License. It also provides other free software developers Less of an
advantage over competing non-free programs. These disadvantages
are the reason we use the ordinary General Public License for many
libraries. However, the Lesser license provides advantages in certain
special circumstances.
For example, on rare occasions, there may be a special need to
encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs must
be allowed to use the library. A more frequent case is that a free library
does the same job as widely used non-free libraries. In this case, there
is little to gain by limiting the free library to free software only, so we use
the Lesser General Public License.
In other cases, permission to use a particular library in non-free
programs enables a greater number of people to use a large body of
free software. For example, permission to use the GNU C Library in
non-free programs enables many more people to use the whole GNU
operating system, as well as its variant, the GNU/Linux operating
system.
Although the Lesser General Public License is Less protective of the
users’ freedom, it does ensure that the user of a program that is linked
with the Library has the freedom and the wherewithal to run that
program using a modified version of the Library.
The precise terms and conditions for copying, distribution and
modification follow. Pay close attention to the difference between a
“work based on the library” and a “work that uses the library”. The
former contains code derived from the library, whereas the latter must
be combined with the library in order to run.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other
program which contains a notice placed by the copyright holder or
other authorized party saying it may be distributed under the terms of
this Lesser General Public License (also called “this License”). Each
licensee is addressed as “you”.
A “library” means a collection of software functions and/or data
prepared so as to be conveniently linked with application programs
(which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which
has been distributed under these terms. A “work based on the Library”
means either the Library or any derivative work under copyright law: that
is to say, a work containing the Library or a portion of it, either verbatim
or with modifications and/or translated straightforwardly into another
language. (Hereinafter, translation is included without limitation in the
term “modification”.)
“Source code” for a work means the preferred form of the work for
making modifications to it. For a library, complete source code means
all the source code for all modules it contains, plus any associated
interface definition files, plus the scripts used to control compilation and
installation of the library.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of running a
program using the Library is not restricted, and output from such a
program is covered only if its contents constitute a work based on the
Library (independent of the use of the Library in a tool for writing it).
Whether that is true depends on what the Library does and what the
program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library’s
complete source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep intact all
the notices that refer to this License and to the absence of any
warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of
it, thus forming a work based on the Library, and copy and distribute
such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices
stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no
charge to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of
data to be supplied by an application program that uses the
facility, other than as an argument passed when the facility is
invoked, then you must make a good faith effort to ensure that,
in the event an application does not supply such function or
table, the facility still operates, and performs whatever part of its
purpose remains meaningful.
(For example, a function in a library to compute square roots has a
purpose that is entirely well-defined independent of the application.
Therefore, Subsection 2d requires that any application-supplied function
or table used by this function must be optional: if the application does
not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Library, and can be
reasonably considered independent and separate works in themselves,
then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the
same sections as part of a whole which is a work based on the Library,
the distribution of the whole must be on the terms of this License,
whose permissions for other licensees extend to the entire whole, and
thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise the
right to control the distribution of derivative or collective works based on
the Library.
In addition, mere aggregation of another work not based on the Library
with the Library (or with a work based on the Library) on a volume of a
storage or distribution medium does not bring the other work under the
scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public
License instead of this License to a given copy of the Library. To do this,
you must alter all the notices that refer to this License, so that they refer
to the ordinary GNU General Public License, version 2, instead of to this
License. (If a newer version than version 2 of the ordinary GNU General
Public License has appeared, then you can specify that version instead
if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy,
so the ordinary GNU General Public License applies to all subsequent
copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the
Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of
it, under Section 2) in object code or executable form under the terms
of Sections 1 and 2 above provided that you accompany it with the
complete corresponding machine-readable source code, which must
be distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange.
If distribution of object code is made by offering access to copy from a
designated place, then offering equivalent access to copy the source
code from the same place satisfies the requirement to distribute the
source code, even though third parties are not compelled to copy the
source along with the object code.
5. A program that contains no derivative of any portion of the Library,
but is designed to work with the Library by being compiled or linked
with it, is called a “work that uses the Library”. Such a work, in isolation,
is not a derivative work of the Library, and therefore falls outside the
scope of this License.
However, linking a “work that uses the Library” with the Library creates
an executable that is a derivative of the Library (because it contains
portions of the Library), rather than a “work that uses the library”. The
executable is therefore covered by this License. Section 6 states terms
for distribution of such executables.
When a “work that uses the Library” uses material from a header file
that is part of the Library, the object code for the work may be a
derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked
without the Library, or if the work is itself a library. The threshold for this
to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure
layouts and accessors, and small macros and small inline functions (ten
lines or less in length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work. (Executables
containing this object code plus portions of the Library will still fall under
Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute
the object code for the work under the terms of Section 6. Any
executables containing that work also fall under Section 6, whether or
not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link
a “work that uses the Library” with the Library to produce a work
containing portions of the Library, and distribute that work under terms
of your choice, provided that the terms permit modification of the work
for the customer’s own use and reverse engineering for debugging such
modifications.
You must give prominent notice with each copy of the work that the
Library is used in it and that the Library and its use are covered by this
License. You must supply a copy of this License. If the work during
execution displays copyright notices, you must include the copyright
notice for the Library among them, as well as a reference directing the
user to the copy of this License. Also, you must do one of these things:
a) Accompany the work with the complete corresponding machinereadable source code for the Library including whatever changes
were used in the work (which must be distributed under Sections
1 and 2 above); and, if the work is an executable linked with the
Library, with the complete machine readable “work that uses the
Library”, as object code and/or source code, so that the user
can modify the Library and then relink to produce a modified
executable containing the modified Library. (It is understood that
the user who changes the contents of definitions files in the
Library will not necessarily be able to recompile the application to
use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the
Library. A suitable mechanism is one that (1) uses at run time a
copy of the library already present on the user’s computer
system, rather than copying library functions into the executable,
and (2) will operate properly with a modified version of the library,
if the user installs one, as long as the modified version is
interface-compatible with the version that the work was made
with.
c) Accompany the work with a written offer, valid for at least three
years, to give the same user the materials specified in
Subsection 6a, above, for a charge no more than the cost of
performing this distribution.
d) If distribution of the work is made by offering access to copy
from a designated place, offer equivalent access to copy the
above specified materials from the same place.
e) Verify that the user has already received a copy of these
materials or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library”
must include any data and utility programs needed for reproducing the
executable from it. However, as a special exception, the materials to be
distributed need not include anything that is normally distributed (in
either source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the executable
runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions
of other proprietary libraries that do not normally accompany the
operating system. Such a contradiction means you cannot use both
them and the Library together in an executable that you distribute.
7. You may place library facilities that are a work based on the Library
side-by-side in a single library together with other library facilities not
covered by this License, and distribute such a combined library,
provided that the separate distribution of the work based on the Library
and of the other library facilities is otherwise permitted, and provided
that you do these two things:
a) Accompany the combined library with a copy of the same work
based on the Library, uncombined with any other library facilities.
This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that
part of it is a work based on the Library, and explaining where to
find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the
Library except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense, link with, or distribute the Library
is void, and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such
parties remain in full compliance.
9. You are not required to accept this License, since you have not signed
it. However, nothing else grants you permission to modify or distribute the
Library or its derivative works. These actions are prohibited by law if you
do not accept this License. Therefore, by modifying or distributing the
Library (or any work based on the Library), you indicate your acceptance
of this License to do so, and all its terms and conditions for copying,
distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the
Library), the recipient automatically receives a license from the original
licensor to copy, distribute, link with or modify the Library subject to
these terms and conditions. You may not impose any further restrictions
on the recipients’ exercise of the rights granted herein. You are not
responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute
so as to satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you may not
distribute the Library at all. For example, if a patent license would not
permit royalty free redistribution of the Library by all those who receive
copies directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely from
distribution of the Library.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply, and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or
other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software
distribution system which is implemented by public license practices. Many
people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee cannot impose
that choice.
This section is intended to make thoroughly clear what is believed to be
a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Library under this License may add an
explicit geographical distribution limitation excluding those countries, so
that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if
written in the body of this License.
13. The Free Software Foundation may publish revised and/or new
versions of the Lesser General Public License from time to time. Such
new versions will be similar in spirit to the present version, but may differ
in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library
specifies a version number of this License which applies to it and “any
later version”, you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Library does not specify a license version
number, you may choose any version ever published by the Free
Software Foundation.
14. If you wish to incorporate parts of the Library into other free
programs whose distribution conditions are incompatible with these,
write to the author to ask for permission. For software which is
copyrighted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the free status of
all derivatives of our free software and of promoting the sharing and
reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE
IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED
BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN
WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU.
SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New
Libraries
If you develop a new library, and you want it to be of the greatest
possible use to the public, we recommend making it free software that
everyone can redistribute and change. You can do so by permitting
redistribution under these terms (or, alternatively, under the terms of the
ordinary General Public License).
To apply these terms, attach the following notices to the library. It is
safest to attach them to the start of each source file to most effectively
convey the exclusion of warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is found. one line
to give the library’s name and an idea of what it does.
Copyright (C) year name of author
This library is free software; you can redistribute it and/or modify it under
the terms of the GNU Lesser General Public License as published by
the Free Software Foundation; either version 2.1 of the License, or (at
your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 021101301 USA Also add information on how to contact you by electronic
and paper mail.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the library, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library
‘Frob’ (a library for tweaking knobs) written by James Random Hacker.
signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice.
OpenSSL LICENSE
Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software
must display the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be
used to endorse or promote products derived from this software
without prior written permission. For written permission, please contact
openssl-core@openssl.org.
5. Products derived from this software may not be called “OpenSSL”
nor may “OpenSSL” appear in their names without prior written
permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following
acknowledgment: “This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.
org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ‘‘AS IS’’
AND ANY EXPRESSED OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.This product includes cryptographic software written by Eric
Young (eay@cryptsoft.com). This product includes software written by
Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights
reserved. This package is an SSL implementation written by Eric Young
(eay@cryptsoft.com). The implementation was written so as to conform
with Netscapes SSL. This library is free for commercial and noncommercial use as long as the following conditions are aheared to. The
following conditions apply to all code found in this distribution, be it the
RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL
documentation included with this distribution is covered by the same
copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.
com).
Copyright remains Eric Young’s, and as such any Copyright notices in
the code are not to be removed.
If this package is used in a product, Eric Young should be given
attribution as the author of the parts of the library used. This can be in
the form of a textual message at program startup or in documentation
(online or textual) provided with the package.Redistribution and use in
source and binary forms, with or without modification, are permitted
provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this
list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software
must display the following acknowledgement: “This product includes
cryptographic software written by Eric Young (eay@cryptsoft.com)” The
word ‘cryptographic’ can be left out if the rouines from the library being
used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from
the apps directory (application code) you must include an
acknowledgement: “This product includes software written by Tim
Hudson (tjh@cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.The licence and distribution terms for any publically
available version or derivative of this code cannot be changed. i.e. this
code cannot simply be copied and put under another distribution
licence [including the GNU Public Licence.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset,
USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of
where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery
return system.
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
www.samsungipolis.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
PT01-000900A
Your local installer: www.eaglesecuritysolutions.co.uk