Model No.
TH-42LF25U
TH-47LF25U
Operating Instructions
FULL HD LCD Display
English
Before connecting, operating or adjusting this product,
please read these instructions completely.
Please keep this manual for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: To reduce the risk of electric shock, do not remove cover or back.
No user-serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with
arrow-head within a triangle
is intended to tell the user
that parts inside the product
are a risk of electric shock
to persons.
The exclamation point within
a triangle is intended to
tell the user that important
operating and servicing
instructions are in the papers
with the appliance.
WARNING : To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain
or moisture.
Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set.
(including on shelves above, etc.)
WARNING : 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to
qualified service personnel.
2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin
grounding-type power plug. This plug will only fit a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
As an ENERGY STAR® Partner, Panasonic has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
2
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments / accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart / apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.
3
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment
from your new LCD Display.
To obtain maximum benefit from your set, please read these Instructions before making any adjustments,
and retain them for future reference.
Retain your purchase receipt as well, and record the model number and serial number of your set in the
space provided on the rear cover of these instructions.
Visit our Panasonic Web Site
http://panasonic.net
Table of Contents
Important Safety Instructions.................................. 3
FCC STATEMENT ...................................................... 5
Safety Precautions ................................................... 6
Maintenance .............................................................. 7
Accessories .............................................................. 8
Accessories Supplied .............................................. 8
Remote Control Batteries ........................................ 8
Connections .............................................................. 9
AC cord connection and fixing, cable fixing ............. 9
Video equipment connection ................................... 9
VIDEO and COMPONENT / RGB IN connection ..... 10
HDMI connection ....................................................11
DVI-D IN connection ...............................................11
PC Input Terminals connection .............................. 12
SERIAL Terminals connection ............................... 13
Power ON / OFF ...................................................... 14
Selecting the input signal ...................................... 16
Basic Controls ........................................................ 17
ASPECT Controls ................................................... 19
Digital Zoom ............................................................ 20
On-Screen Menu Displays ..................................... 21
Adjusting POS. /SIZE ............................................. 23
PICTURE Adjustments ........................................... 25
ADVANCED SETTINGS ........................................ 26
SOUND Adjustment ................................................ 27
PRESENT TIME SETUP / SET UP TIMER .............. 28
PRESENT TIME SETUP ....................................... 28
SET UP TIMER ..................................................... 29
4
SCREENSAVER (For preventing image retention) .... 30
Setup of SCREENSAVER Time ............................ 31
WOBBLING.............................................................. 31
Reduces power consumption ............................... 32
Customizing the Input labels................................. 33
Selecting the On-Screen Menu Language............ 34
Customizing the On-Screen Menu Display .......... 34
SET UP for MULTI DISPLAY ................................... 35
How to setup MULTI DISPLAY .............................. 35
SET UP for Input Signals ....................................... 37
COMPONENT / RGB IN SELECT ......................... 37
SIGNAL menu ....................................................... 38
3D Y/C FILTER ...................................................... 38
COLOR SYSTEM .................................................. 39
3:2 PULLDOWN .................................................... 39
XGA MODE ........................................................... 39
NOISE REDUCTION ............................................. 40
SYNC .................................................................... 40
Input signal display ................................................ 41
Options Adjustments ............................................. 42
Troubleshooting ..................................................... 44
Applicable input signals ........................................ 45
Shipping condition ................................................. 47
Specifications ......................................................... 48
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC CAUTION:
To assure continued compliance, follow the attached installation instructions and use only shielded interface
cables when connecting to computer or peripheral devices. Any changes or modifications not expressly
approved by Panasonic Corp. of North America could void the user's authority to operate this device.
FCC Declaration of Conformity
Model No. TH-42LF25U, TH-47LF25U
Responsible Party:
Contact Source:
Panasonic Corporation of North America
Three Panasonic Way 2F-5, Secaucus, NJ 07094
Panasonic Solutions Company
Panasonic Plasma Concierge 1-800-973-4390
CANADIAN NOTICE:
This Class B digital apparatus complies with Canadian ICES-003.
Note:
Image retention may occur. If you display a still picture for an extended period, the image might remain on the screen.
However, it will disappear after a while.
Trademark Credits
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Inc., USA.
• SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully
respected.
• HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
5
Safety Precautions
CAUTION
This LCD Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Panasonic Corporation.)
• Pedestal ................................................... TY-STLF20
Always be sure to ask a qualified technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being
played with by young children, creating the potential risk of suffocation.
When using the LCD Display
Do not bring your hands, face or objects close to the
ventilation holes of the Display.
• Top of the Display is usually very hot due to the high temperature
of exhaust air being released through the ventilation holes.
Burns or personal injuries can happen if any body parts are
brought too close. Placing any object near the top of the display
could also result in heat damages to the object as well as to
the Display if its ventilation holes are blocked.
Be sure to disconnect all cables before moving the
Display.
• Moving the Display with its cables attached might damage
the cables which, in turn, can cause fire or electric shock.
Disconnect the power plug from the wall outlet as a
safety precaution before carrying out any cleaning.
• Electric shocks can result if this is not done.
6
Clean the power cable regularly to prevent it from
becoming dusty.
• Built-up dust on the power cord plug can increase humidity
which might damage the insulation and cause fire. Unplug
the cord from the wall outlet and clean it with a dry cloth.
Note:
Image retention may occur. If you display a still picture for an
extended period, the image might remain on the screen. However,
it will disappear after a while.
Safety Precautions
WARNING
Setup
Do not place the Display on sloped or unstable surfaces,
and ensure that the Display does not hang over the edge
of the base.
• The Display may fall off or tip over.
Do not place any objects on top of the Display.
• If water spills onto the Display or foreign objects get inside it,
a short-circuit may occur which could result in fire or electric
shock. If any foreign objects get inside the Display, please
consult an Authorized Service Center.
Do not cover the ventilation holes.
• Doing so may cause the Display to overheat, which can
cause fire or damage to the Display.
Transport only in upright position!
• Transporting the unit with its display panel facing upright or
downward may cause damage to the internal circuitry.
For sufficient ventilation;
Leave a space of 3 15/16” (10 cm) or more at the top, left
and right, and 1 31/32” (5 cm) or more at the rear, and also
keep the space between the bottom of the display and
the floor surface.
Cautions for Wall Installation
• Wall installation should be performed by an installation
professional. Installing the Display incorrectly may lead to an
accident that results in death or serious injury. Furthermore,
when installing on a wall, a UL standard certified wall
hanging bracket (VESA 400 × 400) must be used.
• When installing the Display vertically, be sure to install
the power switch onto the bottom of the Display.
An apparatus with CLASS I construction shall be
connected to a mains socket outlet with a protective
earthing connection.
AC Power Supply Cord
The Display is designed to operate on 110 - 127 V AC,
50/60 Hz.
Do not use any power supply cord other than that
provided with this unit.
• Doing so may cause fire or electric shocks.
Securely insert the power cord plug as far as it will go.
• If the plug is not fully inserted, heat may be generated
which could cause fire. If the plug is damaged or the
wall socket plate is loose, they should not be used.
Do not handle the power cord plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that might damage the power cable.
When disconnecting the power cable, hold the plug,
not the cable.
• Do not make any modifications, place heavy objects on,
place near hot objects, heat, bend, twist or forcefully
pull the power cable. Doing so may cause damage to
the power cable which can cause fire or electric shock.
If damage to the cable is suspected, have it repaired at
an Authorized Service Center.
If the Display will not be used for a long period of time,
unplug the power cord from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound),
or if smoke or an abnormal odor is detected from the
Display, unplug the power cord immediately.
• Continuous use of the Display under these conditions
might cause fire or permanent damage to the unit.
Have the Display evaluated at an Authorized Service
Center. Services to the Display by any unauthorized
personnel are strongly discouraged due to its high
voltage dangerous nature.
If water or foreign objects get inside the Display, if the
Display is dropped, or if the cabinet becomes damaged,
disconnect the power cord plug immediately.
• A short may occur, which could cause fire. Contact an
Authorized Service Center for any repairs that need to be
made.
Ensure that the mains plug is easily accessible.
Maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral
detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.
• Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become
damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise
the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added
and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Display. If water droplets get inside the
unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet
surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact
with articles made from rubber or PVC.
7
Accessories
Accessories Supplied
Check that you have the Accessories and items shown
Operating
Instruction book
CD-ROM
(Operating
instructions)
Remote Control Transmitter
N2QAYB000535
Batteries for the
Remote Control
Transmitter
(AA Size × 2)
AC cord
Remote Control Batteries
Requires two AA batteries.
1. Pull and hold the hook, then
open the battery cover.
2. Insert batteries - note correct
polarity (+ and -).
3. Replace the cover.
“AA” size
+
+
-
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precautions:
1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Display.
6. Do not burn or breakup batteries.
Batteries must not be exposed to excessive heat such as sunshine, fire or the like.
8
Connections
AC cord connection and fixing, cable fixing
AC cord fixing
Unplug the AC cord
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Note:
Make sure that the AC cord is locked on
both the left and right sides.
Unplug the AC cord pressing the
two knobs.
Note:
When disconnecting the AC cord, be
absolutely sure to disconnect the AC
cord plug at the socket outlet first.
Cable fixing
Fix the cable in place using the bead band attached to the display.
1 Remove the bead band
3 Attach the bead band
2 Bundle the cables
Remove
Bead band
Pass through to
the back
Stopper
Bundle the cables
Video equipment connection
AV IN
HDMI1, HDMI2
HDMI Input Terminal
(see page 11)
SERIAL
Control the Display by
connecting to PC.
(see page 13)
AV IN
VIDEO
Composite Video Input Terminal
S-VIDEO
S-VIDEO Input Terminal
(see page 10)
DVI-D IN
DVI-D Input Terminal
(see page 11)
COMPONENT/RGB IN
Component/RGB Video
Input Terminal
(see page 10)
PC IN
PC Input Terminal
(see page 12)
9
Connections
VIDEO and COMPONENT / RGB IN connection
Note:
Additional equipment, cables and adapter plugs shown are not supplied with this set.
DVD Player
VCR
S VIDEO OUT
AUDIO OUT
L
VIDEO OUT
R
RCA-BNC
Adapter plug
RCA-BNC
Adapter plug
S Video Input Terminal
Color Signal
Luminance
Signal
Earth (Color Signal) Earth (Luminance Signal)
Notes:
• Change the “COMPONENT/RGB-IN SELECT” setting in the “SETUP”
menu to “COMPONENT” (when COMPONENT signal connection)
or “RGB” (when RGB signal connection). (see page 37)
• Accepts only RGB signals from COMPONENT/RGB IN terminal
with “SYNC ON G”.
L
R
AUDIO OUT
Computer
10
RGB Camcorder
Y PB PR OUT
RGB OUT
DVD Player
Connections
HDMI connection
[Pin assignments and signal names]
Pin No.
1
2
3
4
5
6
7
8
9
10
Signal Name
Pin No.
T.M.D.S Data2+
11
T.M.D.S Data2
Shield
T.M.D.S Data2T.M.D.S Data1+
T.M.D.S Data1
Shield
T.M.D.S Data1T.M.D.S Data0+
T.M.D.S Data0
Shield
T.M.D.S Data0T.M.D.S Clock+
Signal Name
T.M.D.S Clock
Shield
12
T.M.D.S Clock-
13
CEC
14
Reserved
(N.C. on device)
15
16
17
18
19
HDMI cables
19
SCL
SDA
DDC/CEC
Ground
+5V Power
Hot Plug Detect
18
3 1
4 2
HDMI
AV OUT
HDMI
AV OUT
DVD player
DVD player
Note:
Additional equipment and HDMI cable shown are not supplied with this set.
DVI-D IN connection
PC with DVI-D
video out
Stereo mini plug (M3)
Shared with PC IN.
DVI-video cable with Ferrite core (Within 5 m)
DVI-D Input Connector
Pin Layouts
1
Pin No.
8
9
16
17
24
Connection port view
1
2
3
4
5
6
7
8
9
10
11
12
Signal Name
T.M.D.S. data 2T.M.D.S. data 2+
T.M.D.S. data 2 shield
DDC clock
DDC data
T.M.D.S. data 1T.M.D.S. data 1+
T.M.D.S. data 1 shield
Pin No.
13
14
15
16
17
18
19
20
21
22
23
24
Signal Name
+5 V DC
Ground
Hot plug detect
T.M.D.S. data 0T.M.D.S. data 0+
T.M.D.S. data 0 shield
T.M.D.S. clock shield
T.M.D.S. clock+
T.M.D.S. clock-
Notes:
• Additional equipment and cables shown are not supplied with this set.
• Use the DVI-D cable with Ferrite core complying with the DVI standard. Image deterioration may occur depending
on the length or the quality of the cable.
11
Connections
PC Input Terminals connection
(Female)
COMPUTER
Shared with DVI-D IN.
Audio
Stereo mini plug (M3)
Connect a cable which matches
the audio output terminal on the computer.
Conversion adapter
(if necessary)
RGB
PC cable with
Ferrite core
Mini D-sub 15p
(Male)
Notes:
• Computer signals which can be input are those with a horizontal scanning frequency of 30 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
• The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots
when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show
fine detail with sufficient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need
to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Panasonic recommends using a PC cable that includes a Ferrite core.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
Signal Names for Mini D-sub 15P Connector
Pin No.
5
4
10 9
3
2
8
1
7
1
6
15 14 13 12 11
Pin Layout for PC Input
Terminal
12
2
3
4
5
Signal Name
R
G
B
NC (not connected)
GND (Ground)
Pin No.
6
7
8
9
10
Signal Name
GND (Ground)
GND (Ground)
GND (Ground)
+5 V DC
GND (Ground)
Pin No.
11
12
13
14
15
Signal Name
NC (not connected)
SDA
HD/SYNC
VD
SCL
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the Display is controlled by a computer.
(Male)
COMPUTER
1
2
6
3
7
4
8
5
9
Pin layout for SERIAL Terminal
RS-232C Straight cable
(Female)
D-sub 9p
Notes:
• Use the RS-232C straight cable to connect the computer
to the Display.
• The computer shown is for example purposes only.
• Additional equipment and cables shown are not supplied
with this set.
The SERIAL terminal conforms to the RS-232C interface
specification, so that the Display can be controlled by a
computer which is connected to this terminal.
The computer will require software which allows the
sending and receiving of control data which satisfies the
conditions given below. Use a computer application such as
programming language software. Refer to the documentation
for the computer application for details.
Signal names for D-sub 9P connector
Details
Pin No.
2
3
5
4 • 6
7
8
1 • 9
RXD
TXD
GND
Non use
(Shorted in this set)
NC
These signal names are those of computer specifications.
Communication parameters
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
Flow control
RS-232C compliant
Asynchronous
9600 bps
None
8 bits
1 bit
-
Basic format for control data
The transmission of control data from the computer starts with
a STX signal, followed by the command, the parameters, and
lastly an ETX signal in that order. If there are no parameters,
then the parameter signal does not need to be sent.
STX
C1 C2 C3
Start
(02h)
:
P1 P2 P3 P4 P5
Command
Command
PON
POF
AVL
AMT
IMS
ETX
Colon
Parameter(s)
(1 - 5 bytes)
3-character
command (3 bytes)
End
(03h)
Notes:
• If multiple commands are transmitted, be sure to wait for
the response for the first command to come from this unit
before sending the next command.
• If an incorrect command is sent by mistake, this unit will
send an “ER401” command back to the computer.
• Consult an Authorized Service Center for detail instructions
on command usage.
DAM
Parameter
None
None
**
0
1
None
AV1
AV2
HM1
HM2
DV1
PC1
None
ZOOM
FULL
NORM
ZOM2
Control details
Power ON
Power OFF
Volume 000 - 100
Audio MUTE OFF
Audio MUTE ON
Input select (toggle)
VIDEO input (VIDEO)
COMPONENT/RGB IN input
(Component)
HDMI1 input (HDMI1)
HDMI2 input (HDMI2)
DVI-D IN input (DVI)
PC IN input (PC)
Screen mode select (toggle)
ZOOM1
FULL
4:3
ZOOM2
With the power off, this display responds to PON command
only.
13
Power ON / OFF
Connecting the AC cord plug to the Display.
POWER
Connecting the plug to the Wall Outlet.
Note:
When disconnecting the AC cord, be absolutely sure to
disconnect the AC cord plug at the socket outlet first.
Power switch
Press the Power switch on the Display to turn the set on:
Power-On.
Power Indicator: Green
Remote Control Sensor
Power Indicator
Press the
button on the remote control to turn the Display off.
Power Indicator: Red (standby)
Press the
button on the remote control to turn the Display on.
Power Indicator: Green
Turn the power to the Display off by pressing the POWER switch on the unit, when
the Display is on or in standby mode.
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
14
Power ON / OFF
When first switching on the unit
Following screen will be displayed when the unit is turned on for the first time.
Select the items with the remote control. Unit buttons are invalid.
OSD LANGUAGE
English (UK)
OSD LANGUAGE
Deutsch
1
Select the language.
Français
Italiano
Español
2
Set.
ENGLISH (US)
Русский
PRESENT TIME SETUP
1
Select “DAY” or “PRESENT TIME OF DAY”.
2
Setup “DAY” or “PRESENT TIME OF DAY”.
1
Select “SET”.
2
Set.
PRESENT TIME SETUP
PRESENT TIME OF DAY MON 99 : 99
SET
MON
DAY
99 : 99
PRESENT TIME OF DAY
PRESENT TIME SETUP
PRESENT TIME OF DAY MON 99 : 99
SET
TUE
DAY
10 : 00
PRESENT TIME OF DAY
Notes:
• Once the items are set, the screens won't be displayed when switching on the unit next time.
• After the setting, the items can be changed in the following menus.
OSD LANGUAGE (see page 34)
PRESENT TIME SETUP (see page 28)
Power ON warning message
The following message may be displayed when turning the unit power ON:
No activity power off Precautions
’NO ACTIVITY POWER OFF’ IS ENABLED.
If “NO ACTIVITY POWER OFF” in SET UP menu is set to “ENABLE”, a warning message is displayed every
time the power is turned ON. (see page 32)
This message display can be set with the following menu: Options menu
Power On Message (see page 43)
15
Selecting the input signal
Press to select the input signal to be played back from the equipment which
has been connected to the Display.
Input signals will change as follows:
PC
DVI
HDMI1
HDMI2
VIDEO
Component*
PC: PC input terminal in PC IN.
DVI: DVI input terminal in DVI-D IN.
HDMI1: HDMI input terminal in AV IN (HDMI1).
HDMI2: HDMI input terminal in AV IN (HDMI2).
VIDEO: Video input terminal in AV IN (VIDEO/S-VIDEO).
Component*: Component or RGB input terminal in COMPONENT/RGB IN.
* “Component” may be displayed as “RGB” depending on the setting of
“COMPONENT/RGB-IN SELECT”. (see page 37)
Notes:
• Selecting is also possible by pressing the INPUT button on the
unit.
• Select to match the signals from the source connected to the
component/RGB input terminals. (see page 37)
16
Basic Controls
Main Unit
Brightness Sensor
Detects the brightness in the viewing
environment.
Remote control
sensor
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit will
still consume some power as long as the
power cord is still inserted into the wall
outlet.)
• Standby ......... Red
• Power-ON ...... Green
• POWER MANAGEMENT (DPMS)
....................... Orange (With PC input signal.
See page 32)
Speakers
POWER
Enter / Aspect button
(see page 19, 21)
Main Power On / Off Switch
Volume Adjustment
Volume Up “+” Down “–”
When the menu screen is displayed:
“+” : press to move the cursor up
“–” : press to move the cursor down
(see page 21)
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen
will switch. (see page 21)
Normal Viewing
PICTURE
SET UP
SOUND
POS. /SIZE
INPUT button (Input signal selection)
(see page 16)
17
Basic Controls
Remote Control Transmitter
ACTION button
Press to make selections.
ASPECT button
Press to adjust the aspect.
(see page 19)
Standby (ON / OFF) button
The Display must first be plugged into
the wall outlet and turned on at the power
switch (see page 14).
Press this button to turn the Display On,
from Standby mode. Press it again to turn
the Display Off to Standby mode.
POS. /SIZE button
(see page 23)
PICTURE button
(see page 25)
Sound mute On / Off
Press this button to mute the sound.
Press again to reactivate sound.
Sound is also reactivated when power is
turned off or volume level is changed.
N button
(see page 24, 25, 26, 27)
POSITION buttons
INPUT button
Press to select input signal sequentially.
(see page 16)
OFF TIMER button
The Display can be preset to switch to stand-by after
a fixed period. The setting changes to 30 minutes,
60 minutes, 90 minutes and 0 minutes (off timer
cancelled) each time the button is pressed.
30 MIN
60 MIN
90 MIN
0 MIN
When three minutes remain, “OFF TIMER 3 MIN” will
flash.
The off timer is cancelled if a power interruption
occurs.
AUTO SETUP button
Automatically adjusts the position/
size of the screen. (see page 23)
SET UP button (see page 21)
SOUND button (see page 27)
Volume Adjustment
Press the Volume Up “+” or Down “–”
button to increase or decrease the
sound volume level.
R button (see page 21)
Press the R button to return to
previous menu screen.
RECALL button
Press the “RECALL” button to display
the current system status.
1 Input label
2 Aspect mode (see page 19)
3 Off timer
The off timer indicator is displayed only
when the off timer has been set.
4 Clock display (see page 43)
PC
4:3
4
10:00
OFF TIMER 90MIN
Digital Zoom (see page 20)
18
1
2
3
ASPECT Controls
The Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format
picture.
Note:
Be aware that if you put the display in a public place for commercial purposes or a public showing and
then use the aspect mode select function to shrink or expand the picture, you may be violating the
copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other people
for commercial purposes without the prior permission of the copyright holder.
Press repeatedly to move through the aspect options:
4:3
[from the unit]
ZOOM1
ZOOM2
FULL
The aspect mode changes each time the ENTER button is pressed.
Note:
The aspect mode is memorized separately for each input terminal.
Aspect mode
FULL
Picture
Enlarged screen
Description
The display of the pictures fills the screen.
In the case of SD signals, pictures with a 4:3 aspect ratio are
enlarged horizontally, and displayed. This mode is suited to
displaying anamorphic pictures with a 16:9 aspect ratio.
Pictures with a 4:3 aspect ratio are displayed with their
original aspect ratio. Side panels are displayed at the left
and right edges of the screen.
4:3
ZOOM1
ZOOM2
Pictures with a 16:9 aspect ratio are displayed with their
original aspect ratio. The left and right edges of the pictures
are masked by side panels.
Letterbox pictures with a 16:9 aspect ratio are enlarged
vertically and horizontally so that their display fills the screen.
The top and bottom edges of the pictures are cut off.
Letterbox pictures with a 16:9 aspect ratio are enlarged
vertically and horizontally so that their display fills the screen.
The top and bottom edges as well as the left and right edges
of the pictures are cut off.
19
Digital Zoom
This displays an enlargement of the designated part of the displayed image.
1
Display the operation guide.
Press to access Digital Zoom.
The operation guide will be displayed.
EXIT
1
During Digital Zoom, only the following buttons can be operated.
[Remote control]
POSITION /
ACTION button
2
Select the area of the image to be enlarged.
Press on the enlargement location to select.
The cursor will move.
EXIT
2
3
Select the magnification required for the enlarged display.
Each time this is pressed, the magnification factor changes.
This is shown in the image being displayed.
×1
4
×2
Return to normal display (quit Digital Zoom).
Press to exit from the Digital Zoom.
Notes:
• When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
• The Digital Zoom function cannot be selected while in the following operation state:
When MULTI DISPLAY SETUP is ON (see page 35).
When SCREENSAVER is running. (see page 30)
• While Digital Zoom is in operation, “Adjusting POS. /SIZE” cannot be used.
20
×3
×4
On-Screen Menu Displays
Remote Control
Unit
1 Display the menu screen.
Press to select.
(Example: PICTURE menu)
2 Select the item.
Select.
PICTURE
Press.
NORMALIZE NORMAL
PICTURE MENU
BACKLIGHT
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
STANDARD
100
70
50
50
50
50
NORMAL
Press several times.
Each time the MENU button is pressed, the
menu screen will switch.
Normal Viewing
PICTURE
SET UP
SOUND
POS. /SIZE
Select.
(Example:
PICTURE menu)
Adjust.
3 Set.
Press.
Adjust.
4 Exit the menu.
Press.
Press
to return to the
previous menu.
Press several times.
21
On-Screen Menu Displays
Overview
Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
SET UP
POS. /SIZE
NORMALIZE NORMAL
AUTO SETUP
0
0
0
0
0
0
H-POS
H-SIZE
V-POS
V-SIZE
CLOCK PHASE
DOT CLOCK
1:1 PIXEL MODE
OFF
Page 23, 24
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
SET UP
PICTURE
NORMALIZE NORMAL
STANDARD
100
70
50
50
50
50
NORMAL
PICTURE MENU
BACKLIGHT
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
Page 25, 26
2/2
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
MENU DISPLAY DURATION
MENU TRANSPARENCY
20
15 S
Page 28-41
MULTI DISPLAY SETUP
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
BEZEL H ADJUSTMENT 10
BEZEL V ADJUSTMENT 10
LOCATION
A1
Page 35, 36
ADVANCED SETTINGS
NORMALIZE NORMAL
INPUT LEVEL
GAMMA
AGC
W/B HIGH R
W/B HIGH G
W/B HIGH B
W/B LOW R
W/B LOW G
W/B LOW B
OFF
1
1
SET UP TIMER
0
2.2
OFF
50
50
50
50
50
50
PRESENT TIME OF DAY MON 0 : 03
1
PROGRAM
OFF
TIMER FUNCTION
MON
DAY
POWER MODE
POWER ON
TIME
0 : 00
INPUT
VIDEO
Page 29
Page 25, 26
PRESENT TIME SETUP
PRESENT TIME OF DAY MON 99 : 99
SET
MON
DAY
99 : 99
PRESENT TIME OF DAY
SOUND
NORMALIZE NORMAL
AUDIO MENU
BASS
TREBLE
BALANCE
SURROUND
STANDARD
0
0
0
OFF
Page 27
22
Page 28
SIGNAL
3D Y/C FILTER
COLOR SYSTEM
3 : 2 PULLDOWN
NOISE REDUCTION
[ VIDEO ]
ON
AUTO
OFF
OFF
Page 38-41
SCREENSAVER
PRESENT TIME OF DAY MON 0 : 02
START
OFF
MODE
Page 30, 31
INPUT LABEL
VIDEO
Component
PC
DVI
HDMI1
HDMI2
VIDEO
Component
PC
DVI
HDMI1
HDMI2
Page 33
Adjusting POS. /SIZE
1
2
3
4
Press to display the POS. /SIZE menu.
POS. /SIZE
Press to select the menu to adjust.
NORMALIZE NORMAL
AUTO SETUP
H-POS
H-SIZE
V-POS
V-SIZE
CLOCK PHASE
DOT CLOCK
1:1 PIXEL MODE
Press to adjust the menu.
Press to exit from adjust mode.
0
0
0
0
0
0
OFF
Note:
Unadjustable items are grayed out.
Adjustable items differ
depending on the input signal
and the display mode.
Note:
If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position will shift up or down. This picture
position movement cannot be controlled by the POS. /SIZE function.
AUTO
SETUP
H-POS/V-POS, H-SIZE/V-SIZE, DOT CLOCK and CLOCK PHASE are automatically adjusted when the
RGB or PC signal is received.
This setting only operates when a PC signal or RGB signal is input, and the aspect is “FULL”.
Using Remote Control
When
on the remote control is pressed, “AUTO SETUP” will be executed.
When AUTO SETUP does not work, “INVALID” is displayed.
Notes:
• When digital RGB signal input, DOT CLOCK and CLOCK PHASE cannot be made.
• AUTO SETUP may not work when a cropped or dark image is input. In such case, switch to a bright image
with borders and other objects are clearly shown, and then try auto setup again.
• Depending on the signal, out of alignment may occur after AUTO SETUP. Carry out fine tuning for the
position/size as required.
• If AUTO SETUP cannot set properly for vertical frequency 60Hz XGA signal (1024×768@60Hz and
1366×768@60Hz), pre-selecting the individual signal in “XGA MODE” (see page 39) may results in correct
AUTO SETUP.
• AUTO SETUP does not work well when a signal such as additional information is superimposed out of
valid image period or intervals between synchronizing and image signals are short.
• If AUTO SETUP cannot adjust correctly, select “NORMALIZE” once and press ACTION ( ) then adjust
POS. /SIZE manually.
• If the picture goes off screen in the horizontal direction as a result of performing AUTO SETUP, perform
DOT CLOCK adjustment.
23
Adjusting POS. /SIZE
H-POS
Adjust the horizontal position.
V-POS
Adjust the vertical position.
H-SIZE
Adjust the horizontal size.
V-SIZE
Adjust the vertical size.
CLOCK
PHASE
(During Component, RGB and PC input signal)
Eliminate the flickering and distortion.
DOT
CLOCK
(During Component, RGB and PC input signal)
Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens,
adjust so that any such noise is minimized.
OVER
SCAN
Turn image over scan ON/OFF.
Configurable signals are as follows:
525i, 525p, 625i, 625p, 750/60p, 750/50p (Component Video, DVI, HDMI)
ON
OFF
Notes:
• “OFF” is effective during only “FULL” aspect mode.
• When “OFF” is set, “H-SIZE” and “V-SIZE” cannot be adjusted.
1:1 PIXEL Adjusts the display size when 1125i or 1125p signal is input.
MODE
Notes:
• “ON” is effective during only “FULL” aspect mode.
• Select ON when you would like to replay 1920 × 1080 input signal.
• Applicable input signal;
1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p
• Select OFF when flickering is shown around the image.
• H-SIZE and V-SIZE cannot be adjusted when ON is selected.
OFF
Helpful Hint (
ON
/
NORMALIZE
Normalization)
While the POS. /SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values (except “CLOCK PHASE” and “DOT CLOCK”)
are returned to the factory settings.
24
PICTURE Adjustments
1
2
Press to display the PICTURE menu.
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by looking at the picture behind the menu.
Note:
Menu that cannot be adjusted is grayout. Adjustable menu
changes depending on signal, input and menu setting.
PICTURE
Press the left or right button to switch between modes.
STANDARD
DYNAMIC
CINEMA
NORMALIZE NORMAL
STANDARD
100
70
50
50
50
50
NORMAL
PICTURE MENU
BACKLIGHT
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
STANDARD
For viewing in standard (evening lighting) environments.
This menu selects the normal levels of BRIGHTNESS
and PICTURE.
DYNAMIC
For viewing in brighter environments.
This menu selects higher than normal levels of
BRIGHTNESS and PICTURE.
CINEMA
Ideal for movies.
Press to enter Advanced
Settings.
ADVANCED SETTINGS
Enables fine picture adjustment at a professional level
(see next page).
Note:
If you would like to change the picture and color of the
selected PICTURE menu to something else, adjust using
the items in the PICTURE menu. (see next page)
ADVANCED SETTINGS
NORMALIZE NORMAL
INPUT LEVEL
GAMMA
AGC
W/B HIGH R
W/B HIGH G
W/B HIGH B
W/B LOW R
W/B LOW G
W/B LOW B
Helpful Hint (
Press the left
0
2.2
OFF
or right
NORMAL
button to switch between modes.
WARM
COOL
50
50
50
50
50
50
/
NORMALIZE
Normalization)
While the “PICTURE” menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
25
PICTURE Adjustments
Item
BACKLIGHT
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
Effect
Adjustments
Darker
Brighter
Less
More
Darker
Brighter
Less
More
Reddish
Greenish
Less
More
Adjusts luminance of the back light.
Adjusts the proper picture contrast.
Adjusts for easier viewing of dark
pictures such as night scenes and
black hair.
Adjusts color saturation.
Adjusts for natural flesh tones.
Adjusts picture sharpness.
Notes:
• “COLOR” setting can be adjusted for
Video input signal.
• You can change the level of each function
(BACKLIGHT, PICTURE, BRIGHTNESS,
COLOR, TINT, SHARPNESS) for each
PICTURE MENU.
• The setting details for STANDARD,
DYNAMIC and CINEMA respectively
are memorized separately for each input
terminal.
• The “TINT” setting can be adjusted for
NTSC signal only during Video (S Video)
input signal.
• In PICTURE, there is not a noticeable
change even when contrast is increased
with a bright picture or reduced with a dark
picture.
ADVANCED SETTINGS
Item
INPUT
LEVEL
GAMMA
AGC
W/B HIGH R
W/B HIGH G
W/B HIGH B
W/B LOW R
W/B LOW G
W/B LOW B
Effect
Details
Less
More
Down
Up
OFF
ON
Less
More
Less
More
Less
More
Less
More
Less
More
Less
More
Adjustment of parts which are extremely bright and hard to see.
S CURVE
2.0
2.2
2.6
Increases the brightness of dark signal automatically.
Adjusts the white balance for light red areas.
Adjusts the white balance for light green areas.
Adjusts the white balance for light blue areas.
Adjusts the white balance for dark red areas.
Adjusts the white balance for dark green areas.
Adjusts the white balance for dark blue areas.
Notes:
• Carry out “W/B” adjustment as follows.
1. Adjust the white balance of the bright sections using the “W/B HIGH R” , “W/B HIGH G” and “W/B HIGH B” settings.
2. Adjust the white balance of the dark sections using the “W/B LOW R” , “W/B LOW G” and “W/B LOW B” settings.
3. Repeat steps 1 and 2 to adjust.
Steps 1 and 2 affect each other’s settings, so repeat each step in turn to make the adjustment.
• The adjustment values are memorized separately for each input terminal.
• The adjustment range values should be used as an adjustment reference.
Helpful Hint (
/
NORMALIZE
Normalization)
On the remote control unit, while the “ADVANCED SETTINGS” menu is displayed, if either the N button is pressed at any time
or the ACTION ( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
26
SOUND Adjustment
1
2
SOUND
Press to display the SOUND menu.
NORMALIZE NORMAL
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by listening to the sound.
3
AUDIO MENU
BASS
TREBLE
BALANCE
SURROUND
STANDARD
0
0
0
OFF
Press to exit from adjust mode.
Item
AUDIO MENU
Details
STANDARD: Emits the original sound.
DYNAMIC: Accentuates sharp sound.
CLEAR:
Attenuates human voice.
BASS
Adjusts low pitch sounds.
TREBLE
Adjusts high pitch sound.
BALANCE
SURROUND
Adjusts left and right volumes.
Select ON or OFF.
Note: BASS, TREBLE and SURROUND settings are memorized separately for each AUDIO MENU.
Helpful Hint (
/
NORMALIZE
Normalization)
While the “SOUND” menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
27
PRESENT TIME SETUP / SET UP TIMER
The timer can switch the Display ON or OFF.
Before attempting Timer Set, confirm the PRESENT TIME OF DAY and adjust if
necessary. Then set POWER ON TIME / POWER OFF TIME.
1
2
Press to display the SET UP menu.
SET UP
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
MENU DISPLAY DURATION
MENU TRANSPARENCY
20
2/2
15 S
Press to select SET UP TIMER or
PRESENT TIME SETUP.
Press to display the SET UP TIMER screen or PRESENT TIME SETUP screen.
PRESENT TIME SETUP
1
2
Press to select DAY or PRESENT TIME OF DAY.
PRESENT TIME SETUP
PRESENT TIME OF DAY MON 99 : 99
Press to set up DAY or PRESENT TIME OF DAY.
SET
button: Forward
MON
DAY
button: Back
99 : 99
PRESENT TIME OF DAY
Notes:
• Pressing “ ” or “ ” button once changes PRESENT TIME OF DAY 1 minute.
• Pressing “ ” or “ ” button continuously changes PRESENT TIME OF DAY by 15 minutes.
Press to select SET.
Press to store PRESENT TIME SETUP.
Notes:
• SET cannot be selected unless PRESENT TIME OF DAY is set.
• Unless setting the present time other than “99:99”, “DAY” and “PRESENT TIME OF DAY” cannot
be set.
• The settings of “DAY” and “PRESENT TIME OF DAY” are reset when leaving the display turned
off for about 7 days for the following reasons:
Pressing POWER switch of the unit to turn off the display.
Disconnecting the AC cord.
Interruption of power supply.
28
PRESENT TIME SETUP / SET UP TIMER
SET UP TIMER
Set the program for turning the power ON/OFF and select the input signal at the specified time. Up to 20 programs can be set.
[Setting Example]
Program 1, Every Monday, 12:00, Power On, Input: VIDEO
SET UP TIMER
PRESENT TIME OF DAY MON 0 : 03
1
PROGRAM
ON
TIMER FUNCTION
MON
DAY
POWER MODE
POWER ON
TIME
12 : 00
INPUT
VIDEO
1 select
2 adjust
1
Set the program number.
2
To execute the program, set to “ON”.
The program is disabled when “OFF” is set.
3
Set the day.
The program is executed every day when “EVERYDAY” is
set.
4
Set the power ON/OFF.
5
Set the time.
Pressing “ ” or “ ” button once changes “TIME” 1 minute.
Pressing “ ” or “ ” button continuously changes “TIME” by 15
minutes.
6
Set the input.
Notes:
• This function cannot be set unless “PRESENT TIME SETUP” is set.
• If more than one programs are set for the same time, only the program with the smallest program number is enabled.
29
SCREENSAVER (For preventing image retention)
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a SCREENSAVER should be used.
When the screen saver is operating, the following 5 patterns are displayed full screen for 5 seconds each.
Black→Dark Gray→Gray→Light Gray→White
1
Press to display the SET UP menu.
Press to select the SCREENSAVER.
2
Press to select the SCREENSAVER screen.
SET UP
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
SCREENSAVER
3
4
PRESENT TIME OF DAY MON 0 : 02
START
OFF
MODE
MODE selection
Press to select the
MODE.
Press to select each
mode items.
START setting
Off
INTERVAL
: Operates when SHOW DURATION and SAVER
DURATION are set up and those times arrive.
TIME OF DAY
: Operates when START TIME and FINISH TIME
are set up and those times arrive.
STANDBY AFTER SCR SAVER: Operates while SCREENSAVER DURATION,
and display enters standby mode.
ON
: Operates when START is selected and the
ACTION ( ) button is pressed.
When the MODE is set to ON, press to select START.
Press to start SCREENSAVER.
The menu screen will disappear and the SCREENSAVER will be activated. To stop the
SCREENSAVER under ON, press the R button or any buttons on the main unit.
Note: When the display is turned off, the SCREENSAVER will be deactivated.
30
SCREENSAVER (For preventing image retention)
Setup of SCREENSAVER Time
After selecting TIME OF DAY, INTERVAL or STANDBY AFTER SCR SAVER, the relevant Time Setup will become available
for selection and the Operating Time may be set. (Time cannot be set when “MODE” is “ON” or “OFF”.)
Press to select START TIME / FINISH TIME (When TIME OF
DAY is selected).
Press to select SHOW DURATION / SAVER DURATION (When
INTERVAL is selected).
Press to select SCREENSAVER DURATION (When STANDBY
AFTER SCR SAVER is selected).
Press to setup.
button: Forward
button: Back
Notes:
• Pressing “ ” or “ ” button once changes the Time 1 minute.
[However, switching occurs every 15 minutes when Periodic Time is selected.]
• Pressing “ ” or “ ” button continuously changes the Time by 15 minutes.
• “SCREENSAVER DURATION” of the “STANDBY AFTER SCR SAVER” can
be set from 0:00 to 23:59. When this is set to “0:00”, “STANDBY AFTER SCR
SAVER” will not be activated.
SCREENSAVER
PRESENT TIME OF DAY MON 15 : 00
START
TIME OF DAY
MODE
6 : 15
START TIME
12 : 30
FINISH TIME
SCREENSAVER
PRESENT TIME OF DAY MON 15 : 00
START
INTERVAL
MODE
12 : 00
SHOW DURATION
3 : 00
SAVER DURATION
SCREENSAVER
PRESENT TIME OF DAY MON 15 : 00
START
STANDBY AFTER SCR SAVER
MODE
6 : 15
SCREENSAVER DURATION
Note: Timer function will not work unless “PRESENT TIME OF DAY” is set.
WOBBLING
Automatically shifts the display image (therefore unnoticeable to the eye) to prevent image retention of sharper contour
of image.
1
2
Press to display the SET UP menu.
Press to select “WOBBLING”.
Press to select “ON” or “OFF”.
ON: Shifts the position of the display image on a fixed time
interval.
3
Press to exit from adjust mode.
Notes:
• If “MULTI DISPLAY SETUP” is set to “ON”, this function does not operate.
• When this function is operating, part of the screen may appear to be missing.
SET UP
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
31
Reduces power consumption
• POWER MANAGEMENT:
• NO SIGNAL POWER OFF:
• NO ACTIVITY POWER OFF:
When this function is set to ON, it operates under the following conditions to turn the power
on or off automatically.
When no pictures are detected for 30 or so seconds during PC signal input:
→ Power is turned off (standby); the power indicator lights up orange.
When pictures are subsequently detected:
→ Power is turned on; the power indicator lights up green.
Notes:
• This function operates only during input from PC IN terminal.
• This function is effective when “SYNC” is set to “AUTO” and during normal viewing (one
picture screen).
Equipment power supply is turned OFF when there is no signal.
When this is set to “ENABLE”, the power supply of the unit goes Off 10 minutes after the
input signals stop.
Note:
This function is effective during normal viewing (one picture screen).
When this function is set to “ENABLE”, the power is turned off (standby) automatically when
there is no operation of the Display for 4 hours.
Starting from 3 minutes before the turn off, the remaining time will be displayed.
PRESS ANY KEY TO ABORT.
NO ACTIVITY POWER OFF
• STANDBY SAVE:
• ECO:
1
Press to select the menu to adjust.
2
Press to select “ON (ENABLE)” or “OFF (DISABLE)”.
ON (ENABLE)
OFF (DISABLE)
3
Press to exit from SET UP.
32
3MIN
When the power is turned off due to this function, a message “LAST TURN OFF DUE TO
’NO ACTIVITY POWER OFF’.” is displayed next time the power is turned on.
Note:
During the screensaver is running, this function is disabled.
When this function is set to “ON”, serial communication is disabled during standby mode,
reducing the power consumption during standby.
To perform serial communication while in standby, set this function to “OFF(SERIAL)”.
However, the standby power consumption is greater than when it is set to “ON”.
Note:
The factory setting is “ON”.
This function adjusts the brightness of the backlight to reduce power consumption.
OFF: This function does not operate.
ON: Backlight brightness is reduced.
SENSOR: The backlight brightness is automatically adjusted according to the viewing
environment.
Note:
When this function is set to “ON” or “SENSOR”, the “BACKLIGHT” setting in the PICTURE
menu is disabled.
SET UP
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
Customizing the Input labels
This function can change the label of the Input signal to be displayed. (see page 16)
1
2
3
SET UP
Press to display the SETUP menu.
Press to select INPUT LABEL.
Press to display the INPUT LABEL screen.
Press to select image input.
Press to change input label.
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
INPUT LABEL
VIDEO
Component
PC
DVI
HDMI1
HDMI2
Image input
[VIDEO]
[Component]*
[PC]
[DVI]
[HDMI1]
[HDMI2]
VIDEO
Component
PC
DVI
HDMI1
HDMI2
Input label
VIDEO / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
Component / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
PC / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
DVI / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
HDMI1 / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
HDMI2 / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB / (SKIP)
(SKIP) : The INPUT button press will skip its input.
* “Component” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”.
(see page 37)
33
Selecting the On-Screen Menu Language
1
2
Press to display the SET UP menu.
Press to select OSD LANGUAGE.
Press to select your preferred language.
Selectable languages
English (UK)
Deutsch
Français
Italiano
Español
English (US)
......(Chinese)
SET UP
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
.......(Japanese)
Русский.......(Russian)
Customizing the On-Screen Menu Display
Set the display time and background transparency of the on-screen menu display.
1
2
Press to display the SET UP menu.
Press to select “MENU DISPLAY DURATION”.
Press to adjust the display duration.
3
Press to select “MENU TRANSPARENCY”.
Press to adjust the transparency.
4
34
Press to exit from adjust mode.
SET UP
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
MENU DISPLAY DURATION
MENU TRANSPARENCY
20
2/2
15 S
SET UP for MULTI DISPLAY
By lining up the Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across all
screens.
For this mode of operation, each display has to be set up with a Display number to determine its location.
(Example)
group of 4 (2 × 2) group of 9 (3 × 3)
group of 16 (4 × 4)
group of 25 (5 × 5)
How to setup MULTI DISPLAY
1
SET UP
Press to display the SET UP menu.
Press to select the MULTI DISPLAY SETUP.
2
Press to display the “MULTI DISPLAY SETUP” menu.
3
Press to select the MULTI DISPLAY SETUP.
Press to select “ON” or “OFF”.
Item
MULTI DISPLAY SETUP
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
MENU DISPLAY DURATION
MENU TRANSPARENCY
20
2/2
15 S
MULTI DISPLAY SETUP
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
BEZEL H ADJUSTMENT 10
BEZEL V ADJUSTMENT 10
LOCATION
OFF
1
1
A1
Details
Select “ON” or “OFF”.
HORIZONTAL SCALE
Select “1”, “2”, “3”, “4”, “5”.
VERTICAL SCALE
Select “1”, “2”, “3”, “4”, “5”.
Areas of the image that are hidden by the joint sections are adjusted both horizontally and vertically
(0~100).
To show joints between displays.
To hide joints between displays.
Suitable for still image display.
Suitable for moving image display.
Setting value: 0
Setting value: 100
BEZEL H ADJUSTMENT
BEZEL V ADJUSTMENT
35
SET UP for MULTI DISPLAY
Item
Details
Select the required arrangement number. (A1-E5 : Refer to the following)
Display Number locations for each arrangement.
(Examples)
( 2 × 1) ( 2 × 3 )
(4×2)
(4×4)
LOCATION
4
36
(5×5)
A1
Press to exit from adjust mode.
A2
A3
A4
A5
B1
B2
B3
B4
B5
C1
C2
C3
C4
C5
D1
D2
D3
D4
D5
E1
E2
E3
E4
E5
SET UP for Input Signals
COMPONENT / RGB IN SELECT
Select to match the signals from the source connected to the COMPONENT/RGB IN terminal.
Y, PB, PR signals
“COMPONENT”
RGB signals
“RGB”
1
2
Press to display the SET UP menu.
Press to select the “COMPONENT / RGB-IN SELECT”.
Press to select the desired mode.
COMPONENT
RGB
3
Press to exit from adjust mode.
SET UP
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
Note:
Make setting of the selected input terminal (COMPONENT/RGB IN).
37
SET UP for Input Signals
SIGNAL menu
Note:
“SIGNAL” setup menu displays a different setting condition for each input signal.
1
2
SET UP
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
Press to display the SET UP menu.
Press to select the “SIGNAL”.
Press to display the SIGNAL menu.
Press ACTION ( ) button
3
Press to select the menu to adjust.
For RGB
[ VIDEO ]
SIGNAL
Press to adjust the menu.
4
For VIDEO (S VIDEO)
3D Y/C FILTER
COLOR SYSTEM
3 : 2 PULLDOWN
NOISE REDUCTION
[ RGB ]
SIGNAL
SYNC
3 : 2 PULLDOWN
XGA MODE
NOISE REDUCTION
ON
AUTO
OFF
OFF
AUTO
OFF
1024×768
OFF
H-FREQ. 63.98 kHz
V-FREQ. 60.02 Hz
SIGNAL FORMAT 1280×1024/60
Press to exit from adjust mode.
For COMPONENT
SIGNAL
3 : 2 PULLDOWN
XGA MODE
NOISE REDUCTION
For Digital
[ COMPONENT ]
OFF
1024×768
OFF
H-FREQ. 63.98 kHz
V-FREQ. 60.02 Hz
SIGNAL FORMAT 1280×1024/60
[ Digital ]
SIGNAL
3 : 2 PULLDOWN
NOISE REDUCTION
H-FREQ.
V-FREQ.
DOT CLOCK FREQ.
SIGNAL FORMAT
OFF
OFF
63.98 kHz
60.02 Hz
108.0 MHz
1280×1024/60
3D Y/C FILTER
Select “SIGNAL” from the “SET UP” menu during Video (S Video) input signal mode.
(“SIGNAL [VIDEO]” menu is displayed.)
Press to select the “3D Y/C FILTER”.
Press to set ON / OFF.
38
3D Y/C FILTER
ON
SET UP for Input Signals
COLOR SYSTEM
Select SIGNAL from the “SET UP” menu during Video (S Video) input signal mode.
(“SIGNAL [VIDEO]” menu is displayed.)
Press to select the “COLOR SYSTEM” .
Press to select each function.
If the image becomes unstable:
With the system set on Auto, under conditions of low level or noisy
input signals the image may in rare cases become unstable. Should
this occur, set the system to match the format of the input signal.
SIGNAL
3D Y/C FILTER
COLOR SYSTEM
3 : 2 PULLDOWN
[ VIDEO ]
ON
AUTO
OFF
COLOR SYSTEM: Set the color system to match the input signal. When “AUTO” is set, COLOR SYSTEM will be automatically
selected from NTSC/PAL/SECAM/NTSC 4.43/PAL M/PAL N.
To display PAL60 signal, select “AUTO”.
PAL
NTSC 4.43
AUTO
SECAM
NTSC
PAL M
PAL N
3:2 PULLDOWN
3:2 PULLDOWN: When ON, the display attempts to reproduce a more natural interpretation of sources such as movie
pictures, which are recorded at 24 frames per second.
If the picture is not stable, turn the setting to OFF.
Note:
When ON, this setting only affects the following signal input:
• NTSC / PAL signal input during Video (S Video) input signal.
• 525i(480i), 625i(575i), 1125(1080)/60i signal input during Component input signal.
Press to select “3:2 PULLDOWN”.
3 : 2 PULLDOWN
OFF
Press to set ON/OFF.
XGA MODE
This menu is displayed when the input signal is analog (Component/PC).
This menu sets two types of XGA signals with 60Hz vertical frequency having different aspect ratios and sampling rates
(1,024 × 768 @ 60Hz and 1,366 × 768 @ 60Hz).
When a 1,280 x 768 @ 60Hz input signal is automatically detected, the image is processed as a 1,280 x 768 @ 60Hz
XGA input signal irrespective of this setting.
Press to select “XGA MODE”.
Press to select “1024×768”, “1366×768”.
XGA MODE
1024×768
Note:
After making this setting, be sure to make each adjustment (such as “AUTO SETUP”) on the “POS. /SIZE” menu as
necessary. (see page 23)
39
SET UP for Input Signals
NOISE REDUCTION
Press to select “NOISE REDUCTION”.
(
)
NOISE REDUCTION
OFF
Press to select “OFF”, “AUTO”, “MIN”, “MID”, “MAX”.
AUTO: NOISE REDUCTION will be automatically
selected from “MIN”, “MID” or “MAX”.
Note:
NOISE REDUCTION can be adjusted while a Video or Component signal is being applied.
SYNC
This function operates only during input from PC IN terminal.
Select SIGNAL from the “SET UP” menu during Component input signal.
Press to select the “SYNC”.
Press to adjust.
SIGNAL
SYNC
3 : 2 PULLDOWN
XGA MODE
[ RGB ]
AUTO
OFF
1024×768
Confirm that the input is set to RGB input (this setting is valid only for RGB input signal).
AUTO: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
However, the synchronized signal that is input first is selected.
ON G: Uses a synchronized signal on the Video G signal, which is input from the G connector.
Note:
Accepts only RGB signals from COMPONENT/RGB IN terminal with “SYNC ON G”.
40
SET UP for Input Signals
Input signal display
Displays the frequency and the type of the current input signal.
This display is valid only for COMPONENT/RGB/PC and Digital input signal.
Display range:
Horizontal 30 - 110 kHz
Vertical
48 - 120 Hz
The dot clock frequency is displayed during digital signal input.
Note:
The automatically detected signal format may be displayed differently than the actual
input signal.
H-FREQ. 63.98 kHz
V-FREQ. 60.02 Hz
SIGNAL FORMAT 1280×1024/60
H-FREQ.
V-FREQ.
DOT CLOCK FREQ.
SIGNAL FORMAT
63.98 kHz
60.02 Hz
108.0 MHz
1280×1024/60
41
Options Adjustments
1
Options
Press to display the SET UP menu.
On screen display
Initial input
Initial VOL level
Maximum VOL level
Input lock
Button lock
Remocon User level
Press to select “OSD LANGUAGE”.
2
1/2
On
Off
Off
0
Off
0
Off
Off
Off
Press for more than 3 seconds.
Press to select “Options”.
3
Options
Options
Shipping
2/2
Off-timer function
Enable
Normal
Initial Power Mode
Off
Power On Screen Delay
Off
Clock Display
Power On Message (No activity power off)
Press to display the Options menu.
On
Press to select your preferred menu.
4
Power Switch Lock
Off
Press to adjust the menu.
5
Press to exit from Options menu.
Item
On screen display
Initial input
Initial VOL level
Maximum VOL level
Input lock
42
Adjustments
On: Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after
was pressed.
Off: Hides all the items above from view.
Adjusts the input signal when the unit is turned on.
VIDEO
Component/RGB
PC
DVI
HDMI1
Off
Notes:
• Only the adjusted signal is displayed. (see page 16)
• This menu is available only when “Input lock” is “Off”.
HDMI2
Off
Press
button to adjust the volume when the unit is turned on.
Off
On
Off: Sets normal volume.
On: Sets your preferred volume.
Notes:
• When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
• You can hear the changed volume regardless of your volume setting before opening the options menu if
you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Press
button to adjust the maximum volume.
Off
On
Off: Sets auto maximum volume.
On: Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically
becomes the same as the “Maximum VOL level”.
• The volume display can go up to 100 regardless of the settings.
• You can hear the changed volume regardless of your volume setting before opening the options menu if
you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
Locks the input switch operation.
Off
VIDEO
Component/RGB
PC
DVI
HDMI1
HDMI2
Off
Notes:
• Only the adjusted signal is displayed (see page 16).
• Input switch can be used when this is set to “Off”.
Options Adjustments
Item
Adjustments
Off
On
MENU&ENTER
Off: All the buttons on main unit can be used.
MENU&ENTER: Locks
and
buttons on main unit.
On: Locks all the button on main unit.
Sets Button lock with the unit buttons in the following procedure.
Off: Press four times→Press
four times→Press four times→Press
MENU&ENTER: Press
four times→Press four times→Press
four times→Press
On: Press four times→Press
four times→Press four times→Press
MENU
Button lock
ENTER/
ENTER/
INPUT
ENTER/
INPUT
ENTER/
Remocon User level
Off-timer function
ENTER/
ENTER/
Off
User1
User2
User3
Off: You can use all of the buttons on the remote control.
User1: You can only use
, , , ,
buttons on the remote control.
button on the remote control.
User2: You can only use
User3: Locks all the buttons on remote control.
Enable: Enables the “Off-timer function”.
Disable: Disables the “Off-timer function”.
Note:
When “Disable” is set, the Off-timer is cancelled.
Initial Power Mode
On
Standby
Normal
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Power returns in power On. (Power Indicator : green)
Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.
Power On Screen
Delay
Off
1
2
3....
30
You can set the power-on delay time of the displays to reduce the power load, when you press POWER button
to turn on the multiple displays that are set together, for example, on MULTI DISPLAY system.
Set each display’s setting individually.
Off:
The display will be turned on at the same time as POWER button is pressed.
1 to 30 (sec.): Set the power-on delay time (second).
After pressing POWER button, the display will be powered on with time delay depending on this
setting.
Notes:
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the power cord.
Clock Display
Off: Not display the clock.
On: Display the clock.
The clock is displayed at the lower left of the screen when
button is pressed.
Note: When “PRESENT TIME SETUP” is not set, the clock is not displayed even
if “Clock Display” is “On” (see page 28)
10:00
Power On Message
(No activity power
off)
Whether to show/hide No activity power off Precautions at the time of power ON is set.
On: The warning precautions are shown at the time of power ON.
Off: The warning precautions are not shown at the time of power ON.
Note:
This setting is enabled only if “NO ACTIVITY POWER OFF” is “ENABLE” (see page 32).
Power Switch Lock
Sets the lock setting for the display Power switch.
On: Power switch operation is disabled.
Off: Power switch operation is enabled.
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock” or “Remocon User level” adjustments,
set all the values “Off” so that all the buttons are enabled again.
Press the
button on main unit together with
button on the remote control and hold for more than 5 seconds. The
“Shipping” menu is displayed and the lock is released when it disappears.
43
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Picture
Checks
Sound
Interference
Noisy Sound
Electrical Appliances
Cars / Motorcycles
Fluorescent light
Normal Picture
No Sound
Volume
(Check whether the mute function has been activated on the remote control.)
No Picture
No Sound
Not plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
No Picture
Normal Sound
If a signal with a non-applicable color system format, or frequency is input, only the input
terminal indication is displayed.
No Color
Normal Sound
Color controls set at minimum level. (see page 25, 26)
COLOR SYSTEM (see page 39)
No remote control operations can be performed.
A cracking sound is sometimes heard from the unit.
The top or bottom of the picture on the screen is cut
off when I use the zoom function.
Areas at the top and bottom of the screen where
the image is missing appear when I use the zoom
function.
Check whether the batteries have discharged completely and, if they have not, whether they were
inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a strong fluorescent light.
Check whether the remote control designed specifically for use with the unit is being used. (The unit
cannot be operated by any other remote control.)
If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing
very slight contractions in response to changes in the room temperature. There are no adverse
effects on the performance or other aspects.
Adjust the position of the picture on the screen.
When using a video software program (such as a cinema size program) with a screen wider
than one in the 16:9 mode, blank areas separate from the images are formed at the top and
bottom of the screen.
I can hear sounds coming from inside the unit.
When the power is turned on, a sound of the display panel being driven may be heard: This is
normal and not indicative of malfunctioning.
Parts of the unit become hot.
Even when the temperature of parts of the front, top and rear panels has risen, these temperature
rises will not pose any problems in terms of performance or quality.
Power automatically turns off unexpectedly.
Check the settings of “POWER MANAGEMENT”, “NO SIGNAL POWER OFF” and “NO ACTIVITY
POWER OFF” in the SET UP menu. Any of them may be set to “ON (ENABLE)”. (see page 32)
This LCD Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input signal.
However, this is not a malfunction.
LCD Display panel
Symptoms
Check
The screen darkens slightly when bright pictures with
minimal movements are shown.
The screen will darken slightly when photos, still images of a computer or other pictures with minimal
movements are shown for an extended period. This is done to reduce image retention on the screen
and the shortening of the screen’s service life: It is normal and not indicative of malfunctioning.
The unit digitally processes the various signals in order to reproduce esthetically pleasing
images. As such, it sometimes takes a few moments for the picture to appear when the power
has been turned on, when the input has been switched.
Due to the characteristics of the system used to drive the panel, the edges may appear to flicker
in the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
It takes a while for the picture to appear.
The edges of the images flicker.
There may be red spots, blue spots, green spots and
black spots on the screen.
Image retention appears
44
This is a characteristic of liquid crystal panels and is not a problem. The liquid crystal panel
is built with very high precision technology giving you fine picture details. Occasionally, a few
non-active pixels may appear on the screen as fixed points of red, blue, green, or black. Please
note this does not affect the performance of your LCD.
Image retention may occur. If you display a still picture for an extended period, the image
might remain on the screen. However, it will disappear after a while. This is not considered
as malfunction.
Applicable input signals
*Mark: Applicable input signal
PC signals
Horizontal
Vertical
frequency (kHz) frequency (Hz)
640x400@70Hz
31.46
70.07
640x400@85Hz
37.86
85.08
640x480@60Hz
31.43
59.88
640x480@60Hz
31.47
59.94
640x480@67Hz
35.00
66.67
640x480@72Hz
37.86
72.81
640x480@75Hz
37.50
75.00
640x480@85Hz
43.27
85.01
720x400@70Hz
31.47
70.08
800x600@55Hz
34.50
55.38
800x600@56Hz
35.16
56.25
800x600@60Hz
37.88
60.32
800x600@60Hz
38.00
60.51
800x600@72Hz
48.08
72.19
800x600@75Hz
46.88
75.00
800x600@85Hz
53.67
85.06
852x480@60Hz
31.47
59.94
1,024x768@50Hz
39.55
50.00
1,024x768@60Hz
48.36
60.00
1,024x768@60Hz
48.50
60.02
1,024x768@70Hz
56.48
70.07
1,024x768@75Hz
60.24
74.93
1,024x768@75Hz
60.02
75.03
1,024x768@75Hz
61.01
75.70
1,024x768@85Hz
68.68
85.00
1,024x768@120Hz
97.55
119.99
1,066x600@60Hz
37.64
59.94
1,152x864@60Hz
53.70
60.00
1,152x864@75Hz
67.50
75.00
1,152x900@65Hz
61.20
65.20
1,152x900@66Hz
61.85
66.00
1,152x900@75Hz
71.40
75.60
1,280x768@60Hz
47.78
59.87
1,280x800@50Hz
41.20
50.00
1,280x960@60Hz
60.00
60.00
1,280x960@85Hz
85.94
85.00
1,280x1,024@50Hz
52.70
50.00
1,280x1,024@60Hz
63.34
59.98
1,280x1,024@60Hz
63.90
60.00
1,280x1,024@60Hz
63.37
60.01
1,280x1,024@60Hz
63.74
60.02
1,280x1,024@60Hz
63.98
60.02
1,280x1,024@60Hz
63.79
60.18
1,280x1,024@66Hz
70.66
66.47
1,280x1,024@75Hz
79.98
75.02
1,280x1,024@76Hz
81.13
76.11
1,280x1,024@85Hz
91.15
85.02
1,360x768@60Hz
47.71
60.02
1,366x768@50Hz
39.55
50.00
1,366x768@60Hz
48.36
60.00
1,400x1,050@60Hz
65.12
59.91
1,400x1,050@60Hz
65.32
59.98
1,400x1,050@60Hz
65.35
60.12
1,400x1,050@75Hz
82.28
74.87
1,600x1,200@60Hz
75.00
60.00
1,920x1,080@60Hz
67.50
60.00
1,920x1,200@60Hz
74.04
59.95
Macintosh13" (640x480)
35.00
66.67
MacintoshLC13" (640x480)
34.97
66.60
Macintosh16" (832x624)
49.72
74.55
Macintosh19" (1,024x768)
60.24
75.08
Macintosh21" (1,152x870)
68.68
75.06
Macintosh II (1,280x1,024)
80.00
75.00
Signal name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
RGB IN
(Dot clock (MHz))
* (25.17)
* (31.5)
* (25.15)
* (25.18)
* (30.24)
* (31.5)
* (31.5)
* (36.0)
* (28.32)
* (35.33)
* (36.0)
* (40.0)
* (40.13)
* (50.0)
* (49.5)
* (56.25)
* (33.54)
* (51.89)
* (65.0)
* (64.99)
* (75.0)
* (80.0)
* (78.75)
* (80.05)
* (94.5)
* (53.0)
* (81.62)
* (108.0)
* (92.0)
* (94.5)
* (105.1)
* (79.50)
* (68.55)
* (108.0)
* (148.5)
* (89.38)
* (108.18)
* (107.35)
* (107.5)
* (108.1)
* (108.0)
* (108.19)
* (119.84)
* (135.0)
* (135.0)
* (85.5)
* (69.92)
* (86.71)
* (121.38)
* (121.75)
* (121.81)
* (156.0)
* (162.0)
* (148.5)
* (30.24)
* (31.33)
* (57.28)
* (80.0)
* (100.0)
* (134.4)
PC IN
DVI-D IN
HDMI1
(Dot clock (MHz)) (Dot clock (MHz)) HDMI2
* (25.17)
* (25.17)
* (31.5)
* (31.5)
* (25.15)
* (25.15)
* (25.18)
* (25.18)
*
* (30.24)
* (30.24)
* (31.5)
* (31.5)
* (31.5)
* (31.5)
* (36.0)
* (36.0)
* (28.32)
* (28.32)
* (35.33)
* (35.33)
* (36.0)
* (36.0)
* (40.0)
* (40.0)
*
* (40.13)
* (40.13)
* (50.0)
* (50.0)
* (49.5)
* (49.5)
* (56.25)
* (56.25)
* (33.54)
* (34.24)
* (51.89)
* (51.89)
* (65.0)
* (65.0)
*
* (64.99)
* (65.18)
* (75.0)
* (75.0)
* (80.0)
* (80.0)
* (78.75)
* (78.75)
* (80.05)
* (81.0)
* (94.5)
* (94.5)
* (115.5)
* (115.5)
* (53.0)
* (53.0)
* (81.62)
* (81.62)
* (108.0)
* (108.0)
* (92.0)
* (92.0)
* (94.5)
* (94.5)
* (105.1)
* (105.1)
* (79.50)
* (79.50)
* (68.55)
* (68.55)
* (108.0)
* (108.0)
* (148.5)
* (148.5)
* (89.38)
* (89.38)
* (108.18)
* (108.18)
* (107.35)
* (107.35)
* (107.5)
* (107.5)
* (108.1)
* (108.1)
* (108.0)
* (108.0)
*
* (108.19)
* (108.19)
* (119.84)
* (119.84)
* (135.0)
* (135.0)
* (135.0)
* (135.0)
* (157.5)
* (157.5)
* (85.5)
* (85.5)
* (69.92)
* (69.92)
* (86.71)
* (87.44)
* (121.38)
* (122.43)
* (121.75)
* (121.75)
* (121.81)
* (121.85)
* (156.0)
* (156.0)
* (162.0)
* (162.0)
* (148.5)
* (148.5)
* (154.0)
* (154.0)
* (30.24)
* (30.24)
* (31.33)
* (31.33)
* (57.28)
* (57.28)
* (80.0)
* (80.0)
* (100.0)
* (100.0)
* (134.4)
* (135.2)
45
Applicable input signals
*Mark: Applicable input signal
Component signals
Signal name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
525(480)/60i
525(480)/60p
625(575)/50i
625(576)/50i
625(575)/50p
625(576)/50p
750(720)/60p
750(720)/50p
1,125(1,080)/60p
1,125(1,080)/60i
1,125(1,080)/50p
1,125(1,080)/50i
1,125(1,080)/24sF
1,125(1,080)/30p
1,125(1,080)/25p
1,125(1,080)/24p
HDMI1
Horizontal
Vertical
COMPONENT IN
DVI-D IN
frequency (kHz) frequency (Hz) (Dot clock (MHz)) (Dot clock (MHz)) HDMI2
15.73
59.94
* (13.5)
* (27.0)
*
31.47
59.94
* (27.0)
* (27.0)
*
15.63
50.00
* (13.5)
15.63
50.00
* (27.0)
*
31.25
50.00
* (27.0)
*
31.25
50.00
* (27.0)
*
45.00
60.00
* (74.25)
* (74.25)
*
37.50
50.00
* (74.25)
* (74.25)
*
67.50
60.00
* (148.5)∗1
* (148.5)
*
33.75
60.00
* (74.25)∗1
* (74.25)
*
56.25
50.00
* (148.5)∗1
* (148.5)
*
28.13
50.00
* (74.25)∗1
* (74.25)
*
27.00
48.00
* (74.25)∗2
33.75
30.00
* (74.25)∗1
* (74.25)
*
28.13
25.00
* (74.25)∗1
* (74.25)
*
27.00
24.00
* (74.25)∗1
* (74.25)
*
∗1: Based on SMPTE 274M standard.
∗2: Based on SMPTE RP211 standard.
Video signals (VIDEO, S-VIDEO)
Signal name
1
2
3
4
5
6
7
46
NTSC
PAL
PAL60
SECAM
NTSC 4.43
PAL N
PAL M
Horizontal
frequency (kHz)
15.73
15.63
15.73
15.63
15.73
15.63
15.73
Vertical
frequency (Hz)
59.94
50.00
59.94
50.00
59.94
50.00
59.94
Shipping condition
This function allows you to reset the unit to the factory setting.
1
SET UP
Press to display the SET UP menu.
Press to select “OSD LANGUAGE”.
2
Press for more than 3 seconds.
3
Press to select “Shipping”.
1/2
SIGNAL
SCREENSAVER
INPUT LABEL
WOBBLING
OFF
COMPONENT/RGB-IN SELECT
RGB
POWER MANAGEMENT
ON
NO SIGNAL POWER OFF
ENABLE
NO ACTIVITY POWER OFF
DISABLE
STANDBY SAVE
ON
ECO
OFF
OSD LANGUAGE
ENGLISH (US)
Options
Shipping
Press to display the Shipping menu.
4
Press to select “YES”.
Shipping
YES
NO
Press to confirm.
5
6
Wait for 10 seconds.
POWER
Press the power switch (POWER) on main unit to turn the power off.
* If the power switch is locked, please disconnect the AC cord plug from the wall outlet.
[from the unit]
1 Press the MENU button till the SET UP menu is displayed.
2 Press the Volume Up “+” or Down “–” button to select “OSD LANGUAGE”.
3 Press and hold the ENTER button till the Shipping menu is displayed.
4 Press the Volume Up “+” or Down “–” button to select “YES”.
5 Press the ENTER button and wait for 10 sec.
6 Press the power switch (POWER) on main unit to turn the power off.
* If the power switch is locked, please disconnect the AC cord plug from the wall outlet.
47
Specifications
TH-42LF25U
Power Source
Power Consumption
Rated Power
Consumption
Stand-by condition
Power off condition
LCD Display panel
Screen size
(No.of pixels)
Operating condition
Temperature
Humidity
Applicable signals
Color System
Scanning format
PC signals
Connection terminals
VIDEO
AV IN
S-VIDEO
AUDIO L-R
HDMI 1/2
COMPONENT/RGB IN
G/Y
B/PB/CB
R/PR/CR
AUDIO L-R
DVI-D IN
AUDIO
PC IN
AUDIO
SERIAL
TH-47LF25U
110 - 127 V AC, 50/60 Hz
250 W
300 W
0.1 W
0.1 W
42-inch IPS panel, 16:9 aspect ratio
36.6” (930 mm) (W) × 20.5” (523 mm) (H) ×
42.0” (1,067 mm) (diagonal)
2,073,600 (1,920 (W) × 1,080 (H))
[5,760 × 1,080 dots]
0.1 W
0.1 W
47-inch IPS panel, 16:9 aspect ratio
40.9” (1,040 mm) (W) × 23.0” (585 mm) (H) ×
46.9” (1,193 mm) (diagonal)
2,073,600 (1,920 (W) × 1,080 (H))
[5,760 × 1,080 dots]
32 °F - 104 °F (0 °C - 40 °C)
20 % - 80 %
32 °F - 104 °F (0 °C - 40 °C)
20 % - 80 %
NTSC, PAL, PAL60, SECAM, NTSC 4.43, PAL M, PAL N
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 60p · 50i · 50p
· 24p · 25p · 30p · 24sF
VGA, SVGA, XGA, SXGA
UXGA ···· (compressed)
Horizontal scanning frequency 30 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
BNC
Mini DIN 4PIN
RCA Pin jack × 2
BNC
BNC
BNC
RCA Pin jack × 2
DVI-D 24 Pin
Content Protection
Stereo mini jack (M3) × 1
High-Density Mini D-sub 15 Pin
Stereo mini jack (M3) × 1
External Control Terminal
D-sub 9 Pin
1.0 Vp-p (75 Ω)
Y: 1.0 Vp-p (75 Ω), C: 0.286 Vp-p (75 Ω)
0.5 Vrms
TYPE A Connector × 2
with sync 1.0 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
0.5 Vrms
Compliance with DVI Revision 1.0
Compatible with HDCP 1.1
0.5 Vrms, Shared with PC IN
G with sync 1.0 Vp-p (75 Ω)
G without sync 0.7 Vp-p (75 Ω)
B: 0.7 Vp-p (75 Ω)
R: 0.7 Vp-p (75 Ω)
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms, Shared with DVI-D IN
RS-232C compatible
Sound
Speakers
Audio Output
Dimensions (W × H × D)
Mass (weight)
2.0” (50 mm) × 3.6” (90 mm) × 2 pcs
10 W [5 W + 5 W] (10 % THD)
38.2” (968 mm) × 22.1” (561 mm) × 4.0” (101 mm) 42.5” (1,079 mm) × 24.6” (624 mm) × 4.0” (101 mm)
approx. 39.7 lbs
approx. 50.7 lbs
Note:
Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
48
USA only: This product has a fluorescent lamp that contains mercury.
Disposal may be regulated in your community due to environmental
considerations. For disposal or recycling information, please visit
Panasonic website: http://www.panasonic.com/environmental or call
1-888-769-0149.
Customer’s Record
The model number and serial number of this product can be found on its back cover. You should note this serial number
in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase
to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
© Panasonic Corporation 2011
Panasonic Solutions Company
Unit of Panasonic Corporation of North America
Executive Office :
Three Panasonic Way 2F-5, Secaucus, NJ 07094
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3
Serial Number