SD434-YB
User Manual (English)
SD434-YB
Safety Instructions
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
Warnings and Precautions
The Socket-outlet should be installed near the apparatus and be easily
accessible.
KNOW THESE SAFETY SYMBOLS
Read and follow these instructions
when connecting and using your Public
Information Display:
• Unplug the display if you are not going to use it for an extensive
period of time.
• Unplug the display if you need to clean it with a slightly damp cloth.
The screen many be wiped with a dry cloth when the power is off.
However, never use alcohol, solvents or ammonia-based liquids.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Consult a service technician if the display does not operate normally
when you have followed the instructions in this manual.
• The casing cover should be opened only by qualified service
personnel.
This symbol indicates high voltage is present inside.
It is dangerous to make any kind of contact with any
inside part of this product.
• Keep the display out of direct sunlight and away from stoves or any
other heat sources.
• Remove any object that could fall into the vents or prevent proper
cooling of the display’s electronics.
This symbol alerts you that important literature
concerning operation and maintenance has been
included with this product.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to
rain or excessive moisture.
CAUTION:FCC/CSA regulations state that any unauthorized
changes or modifications to this equipment may void
the user’s authority to operate it.
• If turning off the display by detaching the power cable, wait for 6
seconds before re-attaching the power cable for normal operation.
• To avoid the risk of shock or permanent damage to the set do not
expose the display to rain or excessive moisture.
CAUTION:To prevent electric shock, match the wide blade of plug
to the wide slot, and fully insert the plug.
• When positioning the display, make sure the power plug and outlet
are easily accessible.
• IMPORTANT: Always activate a screen saver program during your
application. If a still image in high contrast remains on the screen for
an extended period of time, it may leave an ‘after-image’ or ‘ghost
image’ on the front of the screen. This is a well-known phenomenon
that is caused by the shortcomings inherent in LCD technology. In
most cases the afterimage will disappear gradually over a period
of time after the power has been switched off. Be aware that the
after-image symptom cannot be repaired and is not covered under
warranty.
ii
SD434-YB
Important Safety Instructions
contained in the operating instructions unless you are
qualitified to do so.
1. Read these instructions.
CAUTION:Excessive sound pressure from earphones and
headphones can cause hearing loss. Adjustment of the
equalizer to maximum increases the earphone and
headphone output voltage and the sound pressure level.
Therefore, to protect your hearing, adjust the equalizer
to an appropriate level.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
For UL/CUL application: For use only with UL Listed Wall Mount
Bracket with minimum weight/load: W Kg
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Model Name
W (kg)
SD434-YB
8.7
For CB application: Unit without base weight: W Kg. The equipment
and its associated mounting means still remain secure during the test.
(Used wall mounting kit as following table shown).
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
WARNING:Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
WARNING:The batteries (batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
WARNING:The mains plug or appliance coupler is used as the
disconnect device,the disconnect device shall remain
readily operable.
WARNING:To prevent the spread of fire, keep candles or other
open flames away from this product at all times.
WARNING:To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions.
CAUTION:These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric
shock,do not perform any servicing other than that
iii
Model Name
Wall Mount Grid
Screw
SD434-YB
400x400, 200x200
M6x(10+X), X=thickness of
wall mount plate
SD434-YB
Regulatory Information
Federal Communications Commission (FCC)
Notice (U.S. Only)
CE Declaration of Conformity
Note: This equipment has been tested and found to
comply with the limits for a Class A digital
This device complies with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States
relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage
Directive (2014/35/EU), RoHS directive (2011/65/EU).
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable
This product has been tested and found to comply with the harmonized
standards for Information Technology Equipment, these harmonized
standards published under Directives of Official Journal of the European
Union.
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if
Warning:
not installed and used in accordance with the
instruction manual, may cause harmful
This equipment is compliant with Class A of EN55032. In a residential
environment this equipment may cause radio interference.
interference to radio communications. Operation of
this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the
interference at his own expense.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when
connecting this display to a computer device.
To prevent damage which may result in fire or shock hazard, do not
expose this appliance to rain or excessive moisture.
.
iv
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
SD434-YB
Polish Center for Testing and Certification
Notice
Information for U.K. only
The equipment should draw power from a socket with an attached
protection circuit (a three-prong socket). All equipment that works
together (computer, display, printer, and so on) should have the same
power supply source.
Important:
WARNING – THIS APPLIANCE MUST BE EARTHED.
(B)
The phasing conductor of the room’s electrical installation should have
a reserve short-circuit protection device in the form of a fuse with a
nominal value no larger than 16 amperes (A).
(A)
To completely switch off the equipment, the power supply cable must
be removed from the power supply socket, which should be located
near the equipment and easily accessible.
A protection mark “B” confirms that the equipment is in compliance
with the protection usage requirements of standards PN-93/T-42107
and PN-89/E-06251.
This apparatus is supplied with an approved moulded 13A plug. To
change a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved
type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut
off and an appropriate 3-pin plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug
without a fuse is used, the fuse at the distribution board should not be
greater than 5A.
NOTE:The severed plug must be destroyed to avoid a possible shock
hazard should it be inserted into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the
following code:
BLUE – “NEUTRAL” (“N”)
BROWN – “LIVE” (“L”)
GREEN & YELLOW – “EARTH” (“E”)
1. The GREEN & YELLOW wire must be connected to the terminal in
the plug which is marked with the letter “E” or by the Earth symbol
or coloured GREEN or GREEN & YELLOW.
2. The BLUE wire must be connected to the terminal which is marked
with the letter “N” or coloured BLACK.
3. The BROWN wire must be connected to the terminal which
marked with the letter “L” or coloured RED.
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead – not simply over the three wires.
v
SD434-YB
North Europe (Nordic Countries)
Information
End of Life Directives-Recycling
Your new Public Information Display contains several
materials that can be recycled for new users.
Placering/Ventilation
Please dispose of according to all Local, State, and
Federal laws.
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG
ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING
PÅPLATS.
Restriction on Hazardous Substances statement
(India)
This product complies with the “India E-waste Rule 2011” and prohibits
use of lead, mercury, hexavalent chromium, polybrominated biphenyls or
polybrominated diphenyl ethers in concentrations exceeding 0.1 weight
% and 0.01 weight % for cadmium, except for the exemptions set in
Schedule 2 of the Rule.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG
STIKKONTAKT ER NEMT TILGÆNGELIGE.
E-Waste Declaration for India
This symbol on the product or on its packaging
indicates that this product must not be disposed of
with your other household waste. Instead it is your
responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment
. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a
manner that protects human health and the environment. For more information about where you can drop
off your waste equipment for recycling in India please
visit the below web link.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN
TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT
KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
End-of-Life Disposal
Your new Public Information Display contains materials that can be
recycled and reused. Specialized companies can recycle your product to
increase the amount of reusable materials and to minimize the amount
to be disposed of.
Please find out about the local regulations on how to dispose of your
old display from your local dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance
to local-state and federal regulations. For additional information on
recycling contact www.eia.org (Consumer Education Initiative)
Waste Electrical and Electronie EquipmentWEEE
Attention users in European Union private households
This marking on the product or on its packaging
illustrates that, under European Directive 2012/19/
EU governing used electrical and electronic appliances,
this product may not be disposed of with normal
household waste. You are responsible for disposal of
this equipment through a designated waste electrical
and electronic equipment collection. To determine
the locations for dropping off such waste electrical
and electronic, contact your local government office,
the waste disposal organization that serves your
household or the store at which you purchased the
product.
vi
SD434-YB
Table Of Contents
1.
2.
3.
Unpacking and Installation........................................................1
1.1.Unpacking..........................................................................................1
1.2. Package Contents.........................................................................1
1.3. Installation Notes..........................................................................1
1.4. Mounting on a Wall.....................................................................2
1.4.1. VESA Grid.....................................................................2
1.5. Using of Remote sensor and power indicator.............3
Parts and Functions....................................................................4
2.1. Control Panel..................................................................................4
2.2. Input/Output Terminals..............................................................5
2.3. Remote Control............................................................................6
2.3.1. General functions......................................................6
2.3.2. Inserting the batteries in the remote
control.............................................................................7
2.3.3. Handling the remote control..............................7
2.3.4. Operating range of the remote control.......7
Connecting External Equipment.............................................8
3.1. Connecting External Equipment (DVD/VCR/VCD).8
3.1.1. Using COMPONENT video input..................8
3.1.2. Using Video Source input......................................8
3.1.3. Using HDMI video input.......................................9
3.2. Connecting a PC...........................................................................9
3.2.1. Using VGA input.........................................................9
3.2.2. Using DVI input..........................................................9
3.2.3. Using HDMI input..................................................10
3.3. Connecting Audio Equipment............................................ 10
3.3.1. Connecting an external audio device......... 10
3.4. Connecting Multiple Displays in a Daisy-chain
Configuration...............................................................................11
3.4.1. Display control connection............................... 11
3.5. IR Pass-through Connection................................................ 11
3.6. Wire-connecting to Network............................................ 12
5.
Change your settings.............................................................. 16
5.1.Settings.............................................................................................16
5.1.1. Picture menu.............................................................16
5.1.2. Sound menu..............................................................17
5.1.3. General settings menu......................................... 17
5.2. Network Settings.......................................................................18
6.
USB device compatibility........................................................ 19
7.
Input Mode................................................................................ 21
8.
Pixel Defect Policy................................................................... 22
8.1. Pixels and Sub-Pixels................................................................22
8.2. Types of Pixel Defects + Dot Definition..................... 22
8.3. Bright Dot Defects....................................................................22
8.4. Dark Dot Defects.....................................................................23
8.5. Proximity of Pixel Defects.................................................... 23
8.6. Pixel Defect Tolerances..........................................................23
8.7.MURA..............................................................................................23
9.
Cleaning and Troubleshooting............................................... 24
9.1.Cleaning...........................................................................................24
9.2.Troubleshooting..........................................................................25
10. Technical Specifications.......................................................... 26
10.1.SD434-YB......................................................................................26
4.Operation.................................................................................. 13
4.1. Change Picture Format.......................................................... 13
4.2. Play Multimedia Files................................................................13
4.2.1. Play files from computer.................................... 13
4.2.2. Play multimedia files from USB device....... 13
4.3. Play options...................................................................................14
4.3.1. Playing music files...................................................14
4.3.2. Playing movie files..................................................14
4.3.3. Playing photo files..................................................15
vii
SD434-YB
1.
Unpacking and Installation
1.1.
Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2.
Package Contents
Please verify that you received the following items with your package content:
• LCD display
• Remote control with AAA batteries
• Power cord (1.5 m)
• VGA cable (1.5 m)
• Quick Start Guide
Remote Control
and AAA Batteries
* The supplied power cord varies depending on destination.
Video Signal Cable
(D-SUB to D-SUB Cable)
Power Cord
Quick Start Guide
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the
safety regulations of the particular country.
• You might like to save the package box and packing material for shipping the display.
1.3.
Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your
service agent.
• The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained
for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life
of the electronic components.
• The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be experienced.
1
SD434-YB
1.4.
Mounting on a Wall
To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface
that complies with TUV-GS and/or UL1678 standard in North America.
Protective Sheet
VESA Grid
Table
1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the
screen face.
2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc).
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment
or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use DS323QBD for M4 and DS433QBD/DS483QBD/DS553QBD for M6 mounting screws (having a length 10 mm longer
than the thickness of the mounting bracket) and tighten them securely.
5. Unit without base weight= W Kg. The equipment and its associated mounting means still remain secure during the test. For use only with UL Listed
Wall Mount Bracket with minimum weight/load: W Kg.
Model Name
W (kg)
Model Name
W (kg)
SD434-YB
8.7
DS553QBD
16.0
1.4.1. VESA Grid
Model Name
SD434-YB
Vesa Grid
200(H) x 200(V)mm / 400(H) x 400(V)mm
Caution:
To prevent the display from falling:
• For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation
instructions, refer to the guide received with the respective bracket.
• To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the
bracket manufacturer for installation location.
2
SD434-YB
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.
100 mm
100 mm
100 mm
100 mm
1.5.
Using of Remote sensor and power indicator
1. Pull down the lens to have better remote control performance and easy to observe the light information of power status
2. Push up the lens before mounting the display for video wall application
3. Pull/Push the lens until hearing the click sound
Push right to collapse the lens
Push left to extend the lens
3
SD434-YB
2.
Parts and Functions
2.1.
Control Panel
MUTE INPUT
1
1
2
3
MENU
4
5
6
7
8
[ ] button
7
Use this button to turn the display on or put the display to standby.
2
Move the highlight bar down to adjust the selected item while OSD
menu is on.
[MUTE] button
Switch the audio mute ON/OFF.
3
8
Choose the input source.
4
] button in the On-Screen-Display menu.
[ ] button
Move the highlight bar up / Increase the adjustment while OSD
menu is on, or increase the audio output level while OSD menu is
off.
5
[ ] button
Move the highlight bar down / Decrease the adjustment while OSD
menu is on, or decrease the audio output level while OSD menu is
off.
6
[MENU] button
Return to previous menu while OSD menu is on, or to activate the
OSD menu when OSD menu is off.
[INPUT] button
• Used as [
[ ] button
[ ] button
Move the highlight bar up to adjust the selected item while OSD
menu is on.
4
SD434-YB
USB
IN
14
OUT
13
RJ45
2
15
12
IN
Input/Output Terminals
11
OUT
2.2.
10
1
R
16
R
L
9
L
8
Y
3
1
4
NOTES:
• This display’s remote control sensor will stop working if the jack
[IR IN] is connected.
MAIN POWER SWITCH
AC IN
• To remotely control your A/V device via this display, refer to
page 11 for IR Pass Through connection.
AC power input from the wall outlet.
3
PC LINE IN
12 RJ-45
Audio input from VGA source (3.5mm stereo phone).
4
LAN control function for the use of remote control signal from control
center.
HDMI IN
HDMI video / audio input.
5
13
DVI-D IN
15 USB
VGA IN (D-Sub)
Y/CVBS
AUDIO IN
AUDIO OUT
Audio output to external AV device.
10 IR
OUT /
LOCK
Used for security and theft prevention.
Audio input from external AV device (RCA).
9
RS232 IN
PORT
16 Security
Video source input.
8
14
Connect your USB storage device.
VGA video input.
7
RS232 OUT /
RS232C network output / input for the loop-through function.
DVI-D video input.
6
Pr
7
6
5
Switch the main power on/off.
2
Pb
11 IR
IN
IR signal output /input for the loop-through function.
5
Remote Control
1
[ ] POWER button
Turn the display on or put the display to standby.
General functions
2
[PLAY] buttons
Control playback of media files.
3
1
[
] SOURCE button
Choose input source. Press [ ] or [ ] button to choose from
USB, Network, HDMI, DVI, YPbPr, AV, or VGA. Press
[
2
3
4
14
5
[
] LIST button
No function.
6
[ ] [ ] [ ] [ ] NAVIGATION buttons
Navigate through menus and choose items.
15
7
[
] button
Confirm an entry or selection.
6
8
7
8
] HOME button
Access the OSD menu.
4
5
[
] button to confirm and exit.
[ ] ADJUST button
Access currently available options, picture and sound menus.
16
9
[
] BACK button
Return to the previous menu page or exit from the previous
function.
9
10
[ ] [ ] VOLUME button
Adjust volume.
10
11
12
11
10
[
] MUTE button
Press to turn the mute function on/off.
12
[
][
][
][
] COLOR buttons
Choose tasks or options.
13
[NUMERIC] buttons
Enter text for network setting.
13
14
[
] FORMAT button
Change picture format.
15
[
] INFO button
Display information about current activity.
16
[ ] OPTIONS button
Access currently available options, picture and sound menus.
6
SD434-YB
2.3.2. Inserting the batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
1. Press and then slide the cover to open it.
2. Align the batteries according to the (+) and (–) indications inside the
battery compartment.
3. Replace the cover.
Caution:
The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:
• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.
• Do not mix battery types.
• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.
• Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment. Don’t touch exposed battery acid, as it can
damage your skin.
NOTE:If you do not intend to use the remote control for a long period, remove the batteries.
2.3.3. Handling the remote control
• Do not subject to strong shock.
• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.
• Avoid exposure to heat and steam.
• Other than to install the batteries, do not open the remote control.
2.3.4. Operating range of the remote control
Point the front of the remote control toward this display’s remote control sensor when
pressing a button.
Use the remote control within a distance of less than 5m/16ft from this display’s sensor,
and a horizontal and vertical angle of less than 30 degrees.
NOTE:The remote control may not function properly when the remote control sensor
on this display is under direct sunlight or strong illumination, or when there is an
obstacle in the path of signal transmission.
30
7
30
SD434-YB
3.
Connecting External Equipment
3.1.
Connecting External Equipment (DVD/VCR/VCD)
3.1.1. Using COMPONENT video input
Audio Out
OUT
IN
RJ45
OUT
IN
USB
COMPONENT Out
(YPbPr)
DVD / VCR / VCD
R
L
R
[R]
L
[L]
[AUDIO IN]
[COMPONENT IN]
(YPbPr)
AC IN
PC Line IN HDMI IN
DVI IN
VGA IN
COMPONENT IN
3.1.2. Using Video Source input
DVD / VCR / VCD
[R]
L
R
L
R
OUT
IN
RJ45
OUT
IN
USB
Y/CVBS Out
[L]
[AUDIO IN]
[Y/CVBS IN]
AC IN
PC Line IN HDMI IN
8
DVI IN
VGA IN
COMPONENT IN
SD434-YB
RJ45
OUT
IN
USB
3.1.3. Using HDMI video input
R
OUT
IN
DVD / VCR / VCD
L
R
L
HDMI Out
[HDMI IN]
AC IN
PC Line IN HDMI IN
3.2.
DVI IN
VGA IN
COMPONENT IN
Connecting a PC
3.2.1. Using VGA input
RJ45
OUT
IN
USB
VGA Out
D-Sub 15 pin
IN
Audio Out
L
R
L
R
OUT
PC
[VGA IN]
[VGA AUDIO IN]
AC IN
PC Line IN HDMI IN
DVI IN
VGA IN
COMPONENT IN
USB
3.2.2. Using DVI input
IN
RJ45
OUT
IN
DVI Out
R
L
R
OUT
PC
L
Audio Out
[DVI IN]
AC IN
PC Line IN HDMI IN
9
[VGA AUDIO IN]
DVI IN
VGA IN
COMPONENT IN
SD434-YB
OUT
IN
USB
3.2.3. Using HDMI input
L
R
OUT
IN
RJ45
HDMI Out
L
R
PC
AC IN
[HDMI IN]
PC Line IN HDMI IN
3.3.
DVI IN
VGA IN
COMPONENT IN
Connecting Audio Equipment
3.3.1. Connecting an external audio device
AUDIO OUT
STEREO AMPLIFIER
AUDIO IN
RJ45
OUT
IN
USB
COMPONENT OUT (YPbPr)
L
R
L
R
OUT
IN
DVD / VCR / VCD
AC IN
PC Line IN HDMI IN
10
DVI IN
VGA IN
COMPONENT IN
SD434-YB
3.4.
Connecting Multiple Displays in a Daisy-chain Configuration
You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall.
3.4.1. Display control connection
Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2.
DISPLAY 1
DISPLAY 2
PC
[RS-232C]
3.5.
[RS-232C IN]
[RS-232C OUT]
[RS-232C IN]
IR Pass-through Connection
[IR OUT]
DVD / VCR / VCD
[IR IN]
(DVD / VCR / VCD)
Remote Control
11
SD434-YB
3.6.
Wire-connecting to Network
If you connect this display to a home network, you can play photos, music and videos from your computer. See Play multimedia files via Local Area Network
(Page 13) for more detail.
INTERNET
ROUTER
[RJ-45]
[RJ-45]
PC
To setup the network:
1. Switch on the router and switch on its DHCP setting.
2. Connect the router to this display with an Ethernet cable.
3. Press [
] HOME button on the remote control, then select Setup.
4. Select Connect to network, then press [
] button.
5. Follow the on-screen instructions to install the network.
6. Wait for this display to find the network connection.
7. If you are prompted, agree to the “End User Licence Agreement”.
NOTE:Connecting with a shielded CAT-5 Ethernet cable to comply with the EMC directive.
12
SD434-YB
Operation
start playing.
4. Press the Play buttons on the remote control to control playing.
NOTE: The control button described in this section is mainly on the
remote control unless specified otherwise..
Tips:
•
Select the top bar to filter your files by type.
Change Picture Format
•
You can change the picture format to suit the video source. Each video
source has its available picture formats.
Select [Sort] to arrange the files by album name, artist, or other
fields.
•
To clear the list of offline media servers, press
button, then select [Clearofflineservers] and press
The available picture formats depend on the video source:
1. Press
button.
Play multimedia files from USB device
button.
2. Press or button to select a picture format, then press
• {Auto zoom}: Enlarge the picture to fill the screen.
Recommended for minimal screen distortion but not for HD or
PC.
USB
{4:3}: Display the classic 4:3 format.
IN
•
OUT
{Unscaled}: Provide maximum detail for PC. Only available
when PC mode is selected in the {Picture} menu.
RJ45
•
IN
{Wide screen}: Shows widescreen format content unstretched.
Not recommended for HD or PC.
USB
OUT
•
1. Connect your USB device to the USB port on this display.
R
{Movie expand 16:9}: Scale 4:3 format to 16:9. Not
recommended for HD or PC.
This display can play music, movie, or photo files from your USB device.
L
R
L
•
button.
Play Multimedia Files
button, select USB, then press
You can play videos, photos, and music on your display from:
2. Press
•
Your computer connected through your network.
•
A USB device connected to this display.
3. The connected USB device is detected automatically for all its
playable files, which will be automatically sorted into 3 types:
,
, and
.
button.
Play files from computer
To play files from computer, you will need:
•
A wired network, connected with a Universal Plug and Play (uPnP)
router.
•
Optional: A LAN cable that connects your display to your network.
•
A media server running on your computer.
•
Appropriate settings on your computer firewall to allow you to run
the media server.
Set up the network
1. Connect your display and the computer to the same network. See
page 12 for connecting your display to a network.
2. Switch on your computer and the router.
BACK button to go up to the top layer in the screen.
4. Press the
button to select the file type. Press
button to enter
Press
its play list.
NOTE: If the apparatus does not return to DLNA mode due to
external electrical disturbances (e.g. electrostatic discharge), user
intervention is required.
5. Select the file you want. Press
Set up media sharing
6. Follow the on-screen instruction to control the play option.
1. Install a media server on your computer to share media files. These
are some media servers:
• For PC: Windows Media Player 11 (or higher) or TVersity
Supported file system:
•
7. Press the PLAY buttons (H F G I J) to control playing.
•
For Mac: Twonky
Play files
button.
2. Select [Browse network], then press
button.
3. Select a file from the content browser, then press
FAT32
Supported file format:
2. Switch on media sharing on your computer using the media server.
For more information on how to set up the media server, refer to
the website of the media server.
1. Press
button to start playing.
button to
13
•
Music: MP3, WMA, M4A, AAC, AC3
•
Movie: AVI, MP4, MOV, MPG/MPEG
•
Photo: JPEG, BMP, GIF
SD434-YB
Caution:
Playing movie files
•
The manufacturer is not responsible if the USB device is not
supported, nor is it responsible for damage to or loss of data in the
device.
1. Select
Do not overload the USB port. If you connect a USB storage
device that consumes more than 500mA power, make sure that it is
connected to its own external power supply.
Track
•
in the top bar.
2. Select a video, then press
button.
NOTE: When you are playing multimedia files from USB device and
turn the display off. It will set input source to the last real input
source, such as CVBS, YPbPr, VGA, HDMI and DVI-D when you
turn the display on next time.
Play options
Playing music files
1. Select
Info
in the top bar.
2. Select one music track, then press
button.
Album
1. Music
05:05
Play All
USB device
Options
•
To play all the videos in a folder, select one video file, then select
{Play All}.
•
To skip to the next or previous video, press
button.
•
To pause the video, press
button. Press
button again to
resume playback.
or
button.
To skip backward or forward 10 seconds, press
•
or
•
To search backward or forward, press G or J button,
press repeatedly to toggle between different speeds.
•
To stop the video, press H button.
Movie options
Info
Play All
Sort
USB device
Options
•
To play all the tracks in a folder, select one music file, then select
{Play All}.
•
To skip to the next or previous track, press
button.
•
•
While playing video, press
button to select an option:
or
To pause the track, press
button. Press
button again to
resume playback.
or
button.
To skip backward or forward 10 seconds, press
•
To search backward or forward, press G or J button,
press repeatedly to toggle between different speeds.
•
To stop the music, press H button.
button, then press
•
{Repeat}: Select {Repeat} to play a track or an album repeatedly, or
select {Play once} to play a track once.
•
{Media Server}: When you play content from a media server, you
can select another media server.
•
{ShuffleOn} / {ShuffleOff}: Enable or disable random play of tracks.
•
{Subtitles}: Select the available subtitle settings.
•
{Subtitle Language}: Select the language for subtitles if available.
•
{Character Set}: Select the correct character set for the subtitles.
•
{Audio Language}: Select an audio language.
•
{Repeat}: Select {Repeat} to play the video file repeatedly or {Play
once} to play the video file once.
•
{Media server}: When you play content from a media server, you
can select another media server.
•
{ShuffleOn} / {ShuffleOff}: Enable or disable random play of video
files.
NOTE: To view information about a video (for example, played position,
duration, title, or date), select the video, then press
button. To hide the information, press
button again.
Music options
While you play music, press
button to select an option:
button, then press
NOTE: To view information about a song (for example, title, artist or
duration), select the song, then press
button. To hide
the information, press
button again.
14
SD434-YB
Playing photo files
1. Select
in the top bar.
button.
2. Select a photo thumbnail, then press
Date
Info
Play All
Sort
USB device
Options
Start a slideshow
If there are multiple photos in a folder, select a photo, then select {Play
All}.
or
button, and
• To skip to the previous or next photo, press
button.
then press
•
To stop the slideshow, press H button.
Slideshow options
While you play a slideshow, press
button to select an option:
button, then press
•
{ShuffleOff} / {ShuffleOn}: Enable or disable random display of
pictures in the slideshow.
•
{Repeat}: Select {Repeat} to watch a slideshow repeatedly or {Play
once} to watch once.
•
{Slideshow Time}: Select the displaying time for each photo in the
slideshow.
•
{Slideshow Transitions}: Select the transition from one photo to the
next.
•
{Media Server}: When you play content from a media server, you
can select another media server.
15
SD434-YB
Change your settings
Settings
Using the remote control:
Picture menu
Picture
Picture style
Sound
Restore style
General settings
Backlight
Network settings
Contrast
Brightness
Hue
Colour
Sharpness
Advanced
Video or PC
Foramat and edges
button to display the OSD menu.
1. Press
button to select its menu item or to adjust its
2. Press , , , or
value. Press
button to confirm.
3. Press
Picture style
Select a predefined picture setting.
button to go back to the previous menu layer.
Restore style
Restore the last-selected predefined picture setting.
button to exit the OSD menu.
4. Press
Using this display’s control buttons:
Backlight
Adjust the brightness of this display’s backlight.
Contrast
Adjust video contrast.
Brightness
Adjust screen brightness.
Hue
Adjust screen hue.
Colour
Adjust the colour saturation of the picture.
Sharpness
Adjust the sharpness of the picture.
Advanced
Access advanced settings such as gamma, tint settings and video contrast
settings.
• {Noise reduction}: Select the amount of noise reduction for the
picture.
•
1. Press
2. Press[
value.
button to display the OSD menu.
][
] [ ] or [ ] button to select menu item or adjust its
3. Press
submenu.
button to confirm menu selection and enter its
4. Press
button to exit the OSD menu.
16
{Gamma}: Adjust the non-linear setting for picture luminance
and contrast.
•
{Color temp.}: Change the colour balance.
•
{Custom color temp.}: Customise colour balance setting.
•
{Advanced sharpness}: Enable superior sharpness, especially on
lines and contours in the picture.
•
{Dynamic contrast}: Dynamically enhance the details in the
dark, medium and light areas of the picture.
•
{Dynamic backlight}: Select a backlight level to optimise
dynamic power consumption and picture contrast.
•
{Colour enhancement}: Dynamically enhance the
•
vividness and details of colours.
SD434-YB
General settings menu
Video or PC
When viewing content from a connected video console, select {Video}
to apply video settings. When a computer is connected through HDMI,
select {PC}.
Make sure that {Format and edges}  {Picture format}  {Unscaled}
is selected so as to view maximum detail.
Picture
Menu language
Sound
Monitor id
General settings
Eco mode
Network settings
Auto search
Format and edges
Access advanced settings to control the displaying format of the picture.
• {Picture format}: Change the picture format.
•
{Screen edges}: Change the picture size.
•
{Picture shift}: If available, move the position of the picture.
Clock
Scheduling
Sleep timer
Auto switch off
Pixel shift
Control settings
Factory settings
Sound menu
Picture
Sound style
Sound
Restore style
General settings
Bass
Network settings
Treble
Menu language
Select language used for OSD menus.
Monitor id
Set the ID number for controlling this display via the RS232C
connection. Each display must have a unique ID number when multiple
sets of this display are connected.
Audio out
Advanced
Eco mode
Set this display to reduce the power consumption automatically.
Auto search
Choose to let this display detect and display available signal sources
automatically.
Sound style
Access predefined sound settings.
Clock
Adjust clock settings.
Restore style
Restore the last-selected predefined sound setting.
Scheduling
This function allows you to program up to 3 different scheduled time
intervals for this display to activate.
Bass
Adjust the bass level of the speaker and headphones.
You can set:
Treble
Adjust the treble level of the speaker and headphones.
Audio out
Adjust audio output volume.
{Speaker}: Turn on or off the internal speakers.
•
{Clear sound}: Enhance sound quality.
Which input source the display will use for each scheduled
activation period.
•
The time for the display to turn on and turn off.
•
The days in a week for the display to activate.
NOTES:
Advanced
Access advanced settings to enhance your audio experience.
• {Auto volume leveling}: Enable the reduction of sudden volume
changes.
•
•
•
We recommend you to set up current date and time in the {Clock}
menu before using this function.
•
After changing the {Clock} option in the {General settings} menu,
you need to set this {Scheduling} again.
Sleep timer
Switch off this display after a specified time.
Auto switch off
Set the time for this display to be switched off after a period of no
activity. Press any key on the remote control to disable this function.
Pixel shift
For video input sources, you may choose {On} to move the screen
image automatically to protect the display from “burn-in” or “after-image”
symptoms 30 seconds after not operating the display.
Control settings
• {Local KB lock}: Choose to enable or disable the keyboard (control
buttons) function of this display.
• {Unlock}: Enable the keyboard function.
17
SD434-YB
•
•
{Lock all}: Lock all keyboard function.
•
{Lock but volume}: Disable all the keyboard function except
the
and
button.
•
{Lock but power}: Disable all the keyboard function except the
button.
{RC lock}: Choose to enable or disable the button function of the
remote control.
• {Unlock}: Enable the button function.
•
{Lock all}: Lock all button function.
•
{Lock but volume}: Disable all the button function except the
button.
•
{Lock but power}: Disable all the button function except the
button.
NOTE: To disable the lock function from [Local KB lock] or [RC
1 9 9 8 on the remote control.
lock] item, press buttons
Factory settings
Reset all your customized settings to the factory defaults.
Network Settings
Picture
View network settings
Sound
Network configuration
General settings
Static IP configuration
Network settings
Digital Media Render...
Network name
View network settings
View connected network status.
Network settings
Select how this display should assign addresses to the network
resources.
Static IP Configuration
Assign {IP address}, {Netmask}, {Gateway}, {DNS1}, and {DNS2} for
this display.
Digital Media Renderer - DMR
Receive multimedia files from Smart Phones or Tablets connected to
your network.
Network name
Rename this display for easy identification if you have more than one
display connected to your network.
18
SD434-YB
USB device compatibility
USB Video Subtitle Formats (for language subtitles, etc.)
File
Extensions
Container
.mpg
mpeg
PS
.vob
.ts
TS
Video codec
Maximum resolution
MPEG-1
MPEG-2
MPEG-4 ASP
H.264
MPEG-2
MPEG-4 ASP
H.264
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
Max.Frame Rate
(fps)
25p,30p,50i,60i
25p,30p,50i,60i
25p,30p,50i,60i
25p,30p,50p,60p,60i
25p,30p,50i,60i
25p,30p,50i,60i
25p,30p,50p,60p,60i
Max.Bit Rate
(Mbps)
30
30
30
30
30
30
30
-
30
25p,30p,50i,60i
25p,30p,50i,60i
25p,30p,50p,60p,60i
30
30
30
-
30
1920x1080i@field rate=50, 60Hz
MVC
1920x1080p@frame rate=24, 25,30Hz
1280x720p@frame rate=50, 60Hz
.ts
.m2ts
.mts
MaTS
TTS
MPEG-2
MPEG-4 ASP
H.264
1920x1080i @ field rate=50, 60Hz
MVC
.mt2
1920x1080
1920x1080
1920x1080
1920x1080p @ frame rate=24, 25,30Hz
1280x720p @ frame rate=50, 60Hz
.ts
.m2ts
AVCHD
.mts
MPEG-2
MPEG-4 ASP
1920x1080
1920x1080
25p,30p,50i,60i
25p,30p,50i,60i
30
30
H.264
1920x1080
25p,30p,50p,60p,60i
30
Audio codec
MPEG-1(L1&L2),
MPEG-1,2,2.5 L3,
AAC/HE-AAC(v1&v2),
DVD-PCM,AC3
MPEG-1(L1&L2),
MPEG-1,2,2.5 L3,
AAC/HE-AAC (v1&v2),
AC3,E-AC3,
Dolby Pulse
MPEG-1(L1&L2),
MPEG-1,2,2.5 L3,
AAC/HE-AAC (v1&v2),
AC3,E-AC3,
Dolby Pulse
MPEG-1(L1&L2),
MPEG-1,2,2.5 L3,
AAC/HE-AAC (v1&v2),
AC3,E-AC3,
Dolby Pulse
MPEG-1(L1&L2),
.ts
.m2ts
1920x1080i@field rate=50, 60Hz
AVCHD
MVC
1920x1080p@frame rate=24, 25,30Hz
MPEG-1,2,2.5 L3,
-
30
1280x720p @ frame rate=50, 60Hz
.mts
AAC/HE-AAC (v1&v2),
AC3,E-AC3,
Dolby Pulse
.m4v
M4V
.ism/
Manifest
.mpd
frag MP4
H.264
H.264
25p,30p,50p,60p,60i
25p,30p,50p,60p,60i
30
30
-
30
25p,30p,50i,60i
30
30
1920x1080i@field rate=50, 60Hz
MVC
1920x1080p@frame rate=24, 25,30Hz
1280x720p @ frame rate=50, 60Hz
MPEG-4 ASP
H.264
.mp4
1920x1080
1920x1080
MP4
1920x1080
1920x1080
1920x1080i@field rate=50, 60Hz
MVC
1920x1080p@frame rate=24, 25,30Hz
-
30
30p,60i
25p,30p,50i,60i
30
30
1280x720p @ frame rate=50, 60Hz
WMV9/VC1
MPEG-4 ASP
.mkv
.mk3d
1920x1080
1920x1080
AAC
AAC/HE-AAC(v1&v2),
AC3,E-AC3,WMA,
WMA-PRO
AAC/HE-AAC(v1&v2),
AC3,E-AC3,WMA,
WMA-PRO
MPEG-1(L1&L2),
MPEG-1,2,2.5 L3,
MKV
H.264
1920x1080
30
AAC/HE-AAC (v1&v2),
AC3,E-AC3, WMA,
WMA-PRO
19
SD434-YB
USB Multimedia Formats
Frequency
Max.Bit Rate
-
(kHz)
48
(Mbps)
384
MPEG-1,2,2.5 L3
-
-
48
192
WMA
-
-
96
192
768
768
WMA,WMA Pro
LPCM
LPCM
-
-
192
768
LPCM
AAC
-
-
48
1024
AAC,HE-AAC(v1&v2)
Playlists
-
-
-
-
-
M4A
-
-
48
1024
AAC,HE-AAC(v1&v2)
File Extensions
Container
Video codec
Maximum
resolution
.mp3
.wma
MP3
WMA
-
.asf
.wma
.wav(PC)
.aif(mac)
(V2 up to V9.2)
WMA Pro
LPCM
.aiff(mac)
.aac
.mp4
.m4a
.pls
.m3u
.m4a
Audio codec
USB Photo Formats
File
Extensions
Container
jpg/jpeg
JPEG
bmp
Video
codec
Maximum Resolution
Frequency
Max.Bit
Rate
Audio
codec
baseline:
color mode = 444,
size <=32768x16128
color mode = 422v,
size <= 16384x16128
color mode = other, not support
-
-
BMP
4096x3072_4bit,
2730x2500_8bit,
2048x1536_16bit,
1500x1200_32bit
-
-
-
png
PNG
4096x3072_4bit,
2730x2500_8bit,
2048x1536_16bit,
1500x1200_32bit
-
-
-
gif
GIF
4096x3072_4bit,
2730x2500_8bit,
2048x1536_16bit,
1500x1200_32bit
-
-
-
NOTES:
• Sound or video may not work if the contents have a standard bit rate/frame rate above the compatible Frame/sec listed in the table above.
• Video content with a Bit rate or Frame rate larger than the rate specified in the table above can cause choppy video during playback.
20
SD434-YB
7.
Input Mode
VGA Resolution:
Standard
Resolution
VGA
Active Resolution
H Pixels
640
V Lines
480
Refresh Rate
Pixel Rate
60 Hz
25.175 MHz
72 Hz
31.5 MHz
75 Hz
31.5 MHz
70 Hz
33.75 MHz
60 Hz
40 MHz
75 Hz
49.5 MHz
60 Hz
65 MHz
75 Hz
78.75 MHz
Aspect Ratio
Stand for Mode
4:3
Video Graphic Array
16:9
Wide Video Graphic Array
4:3
Super VGA
4:3
Extended Graphic Array
WVGA
720
400
SVGA
800
600
XGA
1024
768
WXGA
1280
768
60 Hz
79.5 MHz
5:3
Wide XGA
WXGA
1280
800
60 Hz
79.5 MHz
16:10
Wide XGA
SXGA
1280
960
60 Hz
108 MHz
4:3
Super XGA
SXGA
1280
1024
60 Hz
108 MHz
5:4
Super XGA
WXGA
1360
768
60 Hz
85.5 MHz
16:9
Wide XGA
WXGA
1366
768
60 Hz
85.5 MHz
16:9
Wide XGA
UXGA
1600
1200
60 Hz
162 MHz
4:3
Ultra XGA
HD1080
1920
1080
60 Hz
148.5 MHz
16:9
HD1080
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
29.97 Hz
13.5 MHz
59.94 Hz
27 MHz
4:3
Modified NTSC Standard
25 Hz
13.5 MHz
50 Hz
27 MHz
4:3
Modified PAL Standard
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
74.25 MHz
16:9
Normally DVB Mode
74.25 MHz
16:9
Normally ATSC Mode
148.5 MHz
16:9
Normally ATSC Mode
SDTV Resolution:
Standard
Resolution
480i
480p
576i
576p
Active Resolution
H Pixels
V Lines
720
480
720
576
HDTV Resolution:
Active Resolution
Standard
Resolution
H Pixels
V Lines
720p
1280
720
1080i
1920
1080
1080p
1920
1080
50 Hz
60 Hz
25 Hz
30 Hz
50 Hz
60 Hz
• The PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz).
• Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows).
• Check your PC instruction book for information about connecting your PC to a display.
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some cases, abnormal signals (such as
stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the [INPUT] button to enter the
video mode. Also, make sure that the PC is connected.
• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
• The display settings table complies to the IBM/VESA standards, and based on the analog input.
• The DVI support mode is regarded as same to the PC support mode.
• The best timing for the vertical frequency to each mode is 60Hz.
21
SD434-YB
Pixel Defect Policy
We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality
control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel defects, but guarantees that any Plasma- & LCD- displays with an unacceptable number of defects will be
repaired during the warranty period in line with your local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for the LCD screen. In order to qualify for repair under
warranty, the number of pixel defects must exceed a certain level as shown in the reference table. If the LCD screen is within specification a warranty
exchange / claim back will be refused. Additionally, because some types or combinations of pixel defects are more noticeable than others, sets even higher
quality standards for those.
Pixels and Sub-Pixels
A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and
blue. Many pixels together form an image. When all sub-pixels of a pixel are lit, the three colored
sub-pixels together appear as a single white pixel. When all are dark, the three colored sub-pixels
together appear as a single black pixel. Other combinations of lit and dark sub-pixels appear as
single pixels of other colors.
subpixel
pixel
Types of Pixel Defects + Dot Definition
Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several types of sub-pixel defects within
each category.
Dot definition = What is a defective “Dot”? :
One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to define a defective dot. This means
that a defective dot can consist of one, two or three defective sub-pixels which can be dark or lit.
R G B
One dot = One Pixel; consists of three sub-pixels of Red, Green, and Blue.
Bright Dot Defects
Bright dot defects appear as pixels or sub-pixels that are always lit or “on”. These are the examples of bright dot defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
Red + Blue = Purple
Red + Green = Yellow
Green + Blue = Cyan (Light Blue)
22
Three adjacent lit sub pixels (one white pixel)
SD434-YB
Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects:
One dark dot
Two adjacent dark dots = 1 pair of dark dots
Two dark dots, specifications defines the
minimum distance between dark dots
Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, specifies tolerances for the proximity of pixel
defects. In the table below you can find specifications about:
• Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
•
Minimum distance between dark dots
•
Total no. of all defective dots
Pixel Defect Tolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in Plasma / LCD- display must have pixel or sub-pixel
defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT
1 lit sub pixel
BLACK DOT EFFECT
1 dark sub pixel
TOTAL DOT DEFECTS OF ALL TYPES
ACCEPTABLE LEVEL
2
ACCEPTABLE LEVEL
10
12
NOTE: * 1 or 2 adjacent sub pixel defects = 1 dot defect
MURA
Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels. This is known within the industry as Mura, which is a Japanese
term for “unevenness.” It is used to describe an irregular pattern or area in which uneven screen uniformity appears under certain conditions. Mura is a
result of the deterioration of the liquid crystal alignment layer and is most commonly caused by long-term operation under high ambient temperatures. It
is an industry- wide phenomenon and Mura is not repairable. It is also not covered by our warranty terms.
Mura has been around since the introduction of LCD technology and with screens getting bigger and in operation 24/7, many displays are running in low
light conditions. This all adds to the possibility of Mura affecting displays.
HOW TO SPOT MURA
There are many symptoms of Mura and also multiple causes. Several of these are listed below:
• Impurities or foreign particles in the crystal matrix
•
Uneven distribution of LCD matrix during manufacturing
•
Non-uniform luminance distribution of the backlight
•
Panel assembly induced stress
•
Flaws within the LCD cells
•
Thermal induced stress - high temperature operation over long periods of time
HOW TO AVOID MURA
Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be minimized by these methods:
• Lower the backlight brightness
•
Use a screen saver
•
Reduce the ambient temperature around the unit
23
SD434-YB
9.
Cleaning and Troubleshooting
9.1.
Cleaning
Caution When Using the Display
• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high
temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too
close. Placing any object near the top of the display could also result in heat related damage to the object as well as the display itself.
• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus cause fire
or electric shock.
• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess liquid. Wipe the surface of
the display to remove dirt. Then use a dry cloth of the same type to dry.
• Do not scratch or hit the surface of the panel with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove as much moisture as possible. Wipe
the cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating
problems, electrical and shock hazards may result.
• Do not scratch or hit the cabinet with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
24
SD434-YB
9.2.
Troubleshooting
Symptom
Possible Cause
Remedy
No picture is displayed
1. The power cord is disconnected.
1. Plug in the power cord.
2. The main power switch on the back of the
display is not switched on.
2. Make sure the power switch is switched on.
3. The selected input has no connection.
3. Connect a signal connection to the display.
4. The display is in standby mode.
Interference displayed on the display or audible
noise is heard
Caused by surrounding electrical appliances or
fluorescent lights.
Move the display to another location to see is the
interference is reduced.
Color is abnormal
The signal cable is not connected properly.
Make sure that the signal cable is attached firmly
to the back of the display.
Picture is distorted with abnormal patterns
1. The signal cable is not connected properly.
1. Make sure that the signal cable is attached
firmly.
2. The input signal is beyond the capabilities of
the display.
Display image doesn’t fill up the full size of the
screen
1. The zoom mode is not set correctly.
2. Scan Mode may be set incorrectly to
underscan.
2. Check the video signal source to see if it
is beyond the range of the display. Please
verify its specifications with this display’s
specification section.
Use the Zoom mode or Custom zoom function
in the Screen menu to fine tune display geometry
and time frequency parameter.
3. If the image exceeds the screen size, Scan
Mode may need to be set to Underscan.
Can hear sound, but no picture
Improperly connected source signal cable.
Make sure that both video inputs and sound
inputs are correctly connected.
Can see picture but no sound is heard
1. Improperly connected source signal cable.
1. Make sure that both video inputs and sound
inputs are correctly connected.
2. Volume is turned all the way down.
3. {Mute} is turned on.
4. No external speaker connected.
2. Press [
] or [
] button to hear sound.
3. Switch MUTE off by using the [
] button.
4. Connect external speakers and adjust the
volume to a suitable level.
Some picture elements do not light up
Some pixels of the display may not turn on.
This display is manufactured using an extremely
high level of precision technology: however,
sometimes some pixels of the display may not
display. This is not a malfunction.
After-Images can still be seen on the display
after the display is powered off. (Examples
of still pictures include logos, video games,
computer images, and images displayed in 4:3
normal mode)
A still picture is displayed for an over extended
period of time
Do not allow a still image to be displayed for
an extended period of time as this can cause a
permanent after-image to remain on the display.
25
SD434-YB
10. Technical Specifications
10.1. SD434-YB
Display:
Item
Screen Size (Active Area)
Aspect Ratio
Number of pixels
Pixel pitch
Displayable colors
Brightness (typical)
Contrast ratio (typical)
Viewing angle
Specifications
940.9(H) x 529.25(V)
16:9
1920 (H) x 1080 (V)
0.49(H) x 0.49(V)
16.7M
350 cd/m2
3000:1
178 degrees
In/Out Terminals:
Item
Speaker Output
Internal Speakers
Specifications
10W (L) + 10W (R) [RMS]/16Ω
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
Audio Input
RCA Jack x 2
RCA Jack x 2
0.5V [rms] (Normal) / 2 Channel (L+R)
0.5V [rms] (Normal) / 2 Channel (L+R)
RS232C
RJ-45
HDMI Input
3.5mm phone jack x 1
2.5mm Phone jack x 2
RJ-45 Jack x 1 (8 pin)
HDMI Jack x 1
(Type A) (19 pin)
RS232C in/RS232C out
10/100 LAN Port
Digital RGB: TMDS (Video + Audio)
MAX:
Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Audio - 48 KHz/ 2 Channel (L+R)
DVI-D Input
VGA Input
DVI-D jack
D-Sub Jack x 1 (15 pin)
Supports LPCM only
Digital RGB: TMDS (Video)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
Component Input
RCA Jack x 3
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
Video Input
RCA x 1 (Share with
Component_Y)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
Composite 1V [p-p] (75Ω)
General:
Item
Power Supply
Power Consumption (Max)
Specifications
AC 100 - 240V, 50 - 60Hz, 2.5A
132 W
Power Consumption (typ.)
Power Consumption (Standby & Off)
Dimensions (With Stand) [W x H x D]
Dimensions (Without Stand) [W x H x D]
Weight (With Stand)
99 W
<0.5 W (RS232 in active)
968.2(W)x599.1(H)x329.6(D)
968.2(W)x559.4(H)x59.9(D@Rear Cover)/60.9(D@Wall Mount)
10.57 Kg
Weight (Without Stand)
8.7 Kg
Gross Weight (Without Stand)
12.2 Kg
26
SD434-YB
Environmental Condition:
Item
Temperature
Humidity
Altitude
Operational
Storage
Operational
Storage
Operational
Storage / Shipment
Specifications
0 ~ 40°C
-20 ~ 60°C
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
0 ~ 3,000 m
0 ~ 9,000 m
Internal Speaker:
Item
Type
Input
Impedance
Output Sound Pressure
Frequency Response
Specifications
1 Way 1 Speaker
10 W (RMS)
16Ω
82 dB/W/M
160 Hz ~ 13 KHz
27
2015 © All rights reserved.
Download PDF
Similar pages
transMItter
Datasheet HSRC-302E
User Manual - AG Neovo Service Website
Signal System NTSC 1080/60i, 30p, 24p 720/60p, 30p, 24p - AV-iQ
usb device compatibility - AG Neovo Service Website
VD80SFHD2-B40
25416000406 0
LCD display