technical bulletin installation instructions

TB 9-2320-387-35-4
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
FOR SYSTEMS
SINGLE CHANNEL GROUND AND
AIRBORNE RADIO SYSTEM (SINCGARS)
AN/VRC-88F, AN/VRC-89F, AN/VRC-90F, AN/VRC-91F, AN/VRC-92F
FORCE XXI BATTLE COMMAND, BRIGADE-AND-BELOW (FBCB2)
AN/UYK-128 (V)4
PRECISION LIGHTWEIGHT GPS RECEIVER (PLGR)
AN/PSN-11
ENHANCED POSITION LOCATION REPORTING SYSTEM (EPLRS)
AN/VSQ-2 (V)
VEHICULAR INTERCOMMUNICATION SET (VIS)
AN/VIC-3 (V)20
HF 150 WATT RADIO
TAC-SAT RADIO
FOR VEHICLE
TRUCK, UTILITY: UP-ARMORED CARRIER, 4X4,
M1114 (2320-01-413-3739) (EIC: B6C).
Approved for public release; distribution is unlimited.
HEADQUARTERS, DEPARTMENT OF THE ARMY
OCTOBER 2006
TB 9-2320-387-35-4
LIST OF EFFECTIVE PAGES
NOTE
A vertical line in the outer margins of the page indicates the
portion of text affected by the change.
Dates of issue for original and change pages are:
Original . . . . . . . . . . 0 . . . . . . . . 1 October 2006
TOTAL NUMBER OF PAGES IN THIS PUBLICATION IS 109 PAGES.
Page No.
*Change No.
i–iii/iv (blank) . . . . . . . . . . . . . . . . . . . . . . . . . . . .0
1-1 – 5-84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0
*Zero in this column indicates original page.
A/(B blank)
TB 9-2320-387-35-4
TECHNICAL BULLETIN
NO. 9-2320-387-35-4
HEADQUARTERS,
DEPARTMENT OF THE ARMY
WASHINGTON, D.C., 1 OCTOBER 2006
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
FOR SYSTEMS
SINGLE CHANNEL GROUND AND
AIRBORNE RADIO SYSTEM (SINCGARS)
AN/VRC-88F, AN/VRC-89F, AN/VRC-90F,
AN/VRC-91F, AN/VRC-92F
FORCE XXI BATTLE COMMAND, BRIGADE-AND BELOW (FBCB2)
AN/UYK-128 (V)4
PRECISION LIGHTWEIGHT GPS RECEIVER (PLGR)
AN/PSN-11
ENHANCED POSITION LOCATION REPORTING SYSTEM (EPLRS)
AN/VSQ-2 (V)
VEHICULAR INTERCOMMUNICATION SET (VIS)
AN/VIC-3 (V)20
HF 150 WATT RADIO
TAC-SAT RADIO
FOR VEHICLE
TRUCK, UTILITY: UP-ARMORED CARRIER, 4X4,
M1114 (2320-01-413-3739) (EIC: B6C).
REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS
You can help improve this publication. If you find any mistakes or if you know of a
way to improve the procedures, please let us know. Submit your DA Form 2028
(Recommended Changes to Publications and Blank Forms), through the Internet,
on the Army Electronic Product Support (AEPS) website. The Internet address is
https://aeps.ria.army.mil. The DA Form 2028 is located under the Public Applications
section in the AEPS Public Home Page. Fill out the form and click on SUBMIT. Using this
form on the AEPS will enable us to respond quicker to your comments and better manage
the DA Form 2028 program. You may also mail, fax or E-mail your letter or DA Form 2028
direct to: AMSTA-LC-LPIT / TECH PUBS, TACOM-RI, 1 Rock Island Arsenal, Rock Island,
IL 61299-7630. The email address is TACOM-TECH-PUBS@ria.army.mil. The fax number
is DSN 793-0726 or Commercial (309) 782-0726.
Approved for public release; distribution is unlimited.
i
TB 9-2320-387-35-4
TABLE OF CONTENTS
Page
LIST OF TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii
CHAPTER 1.
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
Section I.
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
Section II.
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
Section III.
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
Section IV.
Maintenance Forms, Records, and Reports . . . . . . . . . . . . . . . . . . . . . . . .
1-1
Section V.
Consolidated Index of Army Publications . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
CHAPTER 2.
PURPOSE OF INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
CHAPTER 3.
COMPLETION TIME FOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . .
3-1
CHAPTER 4.
PREPARATION FOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section I.
Preparation of Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section II.
Items to be Removed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section III.
List of Items to be Retained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section IV.
Preparation of C4ISR Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section V.
Precautions During Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section VI.
Unpack and Inspect Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section VII.
Inventory C4ISR Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section VIII.
Examine Each Item for Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Section IX.
C4ISR Equipment, Distribution, and Consumables . . . . . . . . . . . . . . . . .
4-2
Section X.
Distribution and Issue Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
Section XI.
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
CHAPTER 5.
INSTALLATION PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
Section I.
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
Section II.
Installation of Terminal Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
Section III.
Cab Enclosure Panel, Terminal Board, and Cover Modification . . . . . . .
5-1
Section IV.
B-Beam Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5
Section V.
Assembly of Cab Enclosure Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6
Section VI.
Final Assembly, Terminal Board Wiring, and Terminal Link . . . . . . . . .
5-8
Section VII
Integrated Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-13
Section VIII.
SINCGARS Mounting Tray, Amp Guard, and
FBCB2 Components Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-19
Section IX.
HF 150 Watt Radio Antenna Bracket and Antenna Installation . . . . . .
5-26
Section X.
SINCGARS Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-30
Section XI.
Rear SINCGARS Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-32
ii
TB 9-2320-387-35-4
TABLE OF CONTENTS (Contd)
Page
Section XII.
EPLRS Antenna and Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . .
5-35
Section XIII.
Installation of TAC-SAT Bracket and Antenna . . . . . . . . . . . . . . . . . . . .
5-37
Section XIV.
EPLRS Mounting Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-41
Section XV.
HF 150 Watt Radio Mounting Bracket Installation . . . . . . . . . . . . . . . . .
5-43
Section XVI.
EPLRS User Readout (URO) Installation . . . . . . . . . . . . . . . . . . . . . . . . .
5-44
Section XVII.
TAC-SAT Radio Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-45
Section XVIII.
TAC-SAT Radio and HF Radio Speaker Installation . . . . . . . . . . . . . . . .
5-47
Section XIX.
Coupler Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-48
Section XX.
VIC-3 Mounting Installation: Rear FFCS/L and Cables . . . . . . . . . . . . .
5-52
Section XXI.
PLGR Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-53
Section XXII.
PLGR Power Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-56
Section XXIII.
PLGR Antenna and Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-57
Section XXIV.
Cables Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-60
LIST OF TABLES
Table
Title
Page
4-1.
Kits Parts List for Installation of C4ISR Equipment . . . . . . . . . . . . . . . . . .
4-3
4-2.
Non-Kit Parts List for Installation of C4ISR Equipment . . . . . . . . . . . . . . .
4-4
iii/(iv blank)
TB 9-2320-387-35-4
CHAPTER 1
INTRODUCTION
Section I. SCOPE
1-1.
This technical bulletin provides installation instructions for Command, Control, Communications,
Computers, Intelligence, Surveillance, and Reconnaissance (C4ISR) equipment. The C4ISR
equipment shall be installed in the following vehicle:
Truck, Utility: Up-Armored Carrier, 4x4, M1114
1-2.
The information contained in this technical bulletin is the official authorization to perform the
installation of the C4ISR equipment at the direct support maintenance level through contract
maintenance teams.
2-1.
This technical bulletin is not an authorization for requisition or turn-in of vehicles.
2-2.
This technical bulletin does not establish quantity or types of vehicles assigned to using units.
3-1.
Included in the C4ISR equipment are:
a. Single Channel Ground and Airborne Radio System (SINCGARS), Radio Set
AN/VRC-88F/89F/90F/91F/92F Series
Section II. NOTES
Section III. GENERAL INFORMATION
b. Force XXI Battle Command, Brigade-and-Below (FBCB2), AN/UYK-128 (V)4
c. Precision Lightweight GPS Receiver (PLGR), AN/PSN-11
d. Enhanced Position Location Reporting System (EPLRS), AN/VSQ-2 (V)
e. HF 150 Watt Radio
f. TAC-SAT Radio
g. Vehicular Intercommunication Set (VIS), AN/VIC-3 (V)20
h. Additional terminal boards
3-2.
The C4ISR equipment becomes operable when all the components are installed in the vehicle and
correct power is supplied.
Section IV. MAINTENANCE FORMS, RECORDS, AND REPORTS
Use the following to report any discrepancies:
a. Reports of Maintenance and Unsatisfactory Equipment. See chapter 4, sections VI through VIII
for information.
b. Report of Packaging and Handling Deficiencies. See chapter 4, sections VI through VIII for
information.
c. Discrepancy in Transportation Deficiency Report (TDR) (SF361). See chapter 4, sections VI
through VIII for information.
Section V. CONSOLIDATED INDEX OF ARMY PUBLICATIONS
Refer to the latest issue of DA PAM 25-30 to determine whether there are new changes or additional
publications pertaining to the C4ISR equipment.
1-1/(1-2 blank)
TB 9-2320-387-35-4
CHAPTER 2
PURPOSE OF INSTALLATION
The purpose of installing the C4ISR equipment is to provide the primary means of integrating command
and control capability.
2-1/(2-2 blank)
TB 9-2320-387-35-4
CHAPTER 3
COMPLETION TIME FOR INSTALLATION
A total of 20 man hours are required for two personnel to install the C4ISR equipment. Typical vehicle
downtime is 12 hours.
3-1/(3-2 blank)
TB 9-2320-387-35-4
CHAPTER 4
PREPARATION FOR INSTALLATION
Section I. PREPARATION OF VEHICLE
To prepare the vehicle for installation, ensure that the site includes adequate lighting and a power source
when drilling is required. Inspect the vehicle for damage that could affect installation. Have any such
damage repaired before installing the C4ISR equipment.
Section II. ITEMS TO BE REMOVED
2-1.
Remove batteries. (Refer to TM 9-2320-387-24.)
2-2.
Remove right-hand rear fixed door if desired. (Refer to TM 9-2320-387-24.)
2-3.
Remove right-hand rear cab enclosure panel. (Refer to TM 9-2320-387-24.)
2-4.
Remove standard rack.
2-5.
Remove right rear ammo storage tray.
Section III. LIST OF ITEMS TO BE RETAINED
3-1.
Batteries
3-2.
Right-hand rear cab enclosure (if applicable).
3-3.
Right-hand rear fixed door (if applicable).
Section IV. PREPARATION OF C4ISR EQUIPMENT
To prepare C4ISR equipment, unpack, inspect, and check inventory.
Section V. PRECAUTIONS DURING HANDLING
Observe the following precautions to prevent equipment damage.
a. Keep dust covers in place on connectors.
b. Do not disassemble or modify parts in the C4ISR equipment unless authorized to do so.
c. Keep mounting hardware covered and protected until needed.
Section VI. UNPACK AND INSPECT EQUIPMENT
6-1.
Unpack and inspect packaging for evidence of damage.
6-2.
Any shipping damage should be reported on SF364 Report of Discrepancy (ROD) as prescribed in
AR 735-11-2/DLAR 4140.55/NAVMATINST 4355.73A/AFR 400-64/MCO 4430.F.
Section VII. INVENTORY C4ISR EQUIPMENT
If any item is missing, fill out and forward Transportation Deficiency Report (TDR) (SF361) as described in
AR 55-38/NAVSUPINST 4610.33C/AFR 75-18/MCO P4610.19D/DLAR 450015.
Section VIII. EXAMINE EACH ITEM FOR DAMAGE
If any item is damaged, fill out and forward SF364 Report of Discrepancy (ROD) as prescribed in
AR 735-11-2/DLAR 4140.55/NAVMATINST 4355.73A/AFR 400-64/MCO 4430.F. All damages should be
reported as prescribed by DA PAM 750-8, as contained in the Maintenance Management Update.
4-1
TB 9-2320-387-35-4
Section IX. C4ISR EQUIPMENT, DISTRIBUTION, AND CONSUMABLES
9-1.
Use table 4-1 to identify and inventory C4ISR equipment installation parts supplied in kits.
9-2.
Use table 4-2 to identify and inventory C4ISR equipment installation parts not supplied in kits.
Section X. DISTRIBUTION AND ISSUE INSTRUCTIONS
10-1.
U.S. Forces: Do not requisition C4ISR equipment. They will be shipped automatically.
10-2.
U.S. Army Depots: Requisition C4ISR equipment through supply channels.
10-3.
Multiservice: Instructions shall be included for multiservice modifications.
10-4.
MAP/MAS countries: Instructions shall be provided for MAP/MAS countries.
Section XI. PARTS LIST
KITS REQUIRED FOR THIS INSTALLATION:
•
•
NOTE
Not all material in kits is required for this installation. Material not
used during installation will be returned to stock for disposition in
accordance with AR 725-50.
If maintenance is to be performed on a vehicle with an existing kit,
do not order entire kit for necessary reinstallation.
SINCGARS:
(A): MK-2801
PLGR:
(B): 57K4399
EPLRS:
(C): No kits available
FBCB2:
(D): No kits available
VIS:
(E): No kits available
HF 150 WATT RADIO:
(F): No kits available
TAC-SAT RADIO:
(G): No kits available
4-2
TB 9-2320-387-35-4
MATERIAL REQUIRED FROM KITS:
Table 4-1. Kit Parts List for Installation of C4ISR Equipment.
ITEM
NO.
NOMENCLATURE
PART NUMBER
1.
Bracket, Antenna
A3014546-1
2.
Bracket, Mounting
12480575
3.
Cable Assembly,
Radio Frequency
A3014031-17
5995-01-225-1660
(A)
1
4.
Clamp, Loop
MS21333-67
5340-00-079-7837
(B)
2
5.
Clamp, Loop
MS21333-75
5340-00-050-2740
(A)
3
6.
Clamp, Loop
MS21333-77
5340-00-922-6300
(A)
2
7.
Clamp, Loop
MS21333-78
5340-00-958-8457
(B)
1
8.
Clamp, Loop
MS21333-96
5340-00-088-1255
(B)
1
9.
Gasket
A3013655-1
5330-01-205-2864
(A)
2
10.
Grommet
MS35489-31
5325-00-174-9336
(B)
1
11.
Grommet
12460299
5325-01-492-0008
(B)
1
12.
Mounting Base,
Electrical Equipment
A3013367-1
5975-01-188-8873
(A)
1
13.
Nut, Lock
MS17829-3C
5310-00-689-3877
(B)
4
14.
Screw
MS35206-266
5305-00-984-6213
(B)
4
15.
Screw
MS35207-261
5305-00-990-6444
(B)
1
16.
Screw, Cap
MS35307-365
5305-00-847-1159
(A)
8
17.
Screw, Self-Tapping
9440025
5305-01-197-2320
(B)
2
18.
Terminal Lug
7728777
5940-00-983-4067
(B)
1
19.
Terminal Lug
7728780
5940-01-035-4212
(B)
1
20.
Washer, Lock
MS35338-43
5310-00-045-3296
(B)
1
21.
Washer, Lock
MS35338-44
5310-00-582-5965
(A)
20
22.
Washer, Lock
MS45904-72
5310-00-889-2527
(A)
29
23.
Washer, Lock
MS45904-76
5310-00-061-1258
(A)
8
24.
Washer, Lock
MS35338-43
5310-00-045-3296
(A)
2
4-3
NSN
KIT
5340-01-391-2742
(A)
QTY.
1
N/A
(B)
1
TB 9-2320-387-35-4
MATERIAL REQUIRED BUT NOT INCLUDED IN KITS:
Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment.
ITEM
NO.
NOMENCLATURE
PART NUMBER
NSN
QTY.
1.
Adapter, Antenna
RF-1980-AT001
5985-01-519-6245
1
2.
Adapter Assembly, Interface Device (SIAD) 881331-1
4920-01-478-3722
1
3.
Antenna AS-3900/VRC
A3017889-2
5985-01-308-8988
1
4.
Antenna, AS-3499/VSQ-1
A3005031
5820-01-183-9462
1
5.
Antenna, Element (lower)
A3018230-1
5985-01-201-1498
2
6.
Antenna, Element (upper)
A3017901-2
5985-01-306-4622
2
7.
Antenna, HF
4245
N/A
1
8.
Antenna, PLGR
AT575-030
5985-01-375-4660
1
9.
Assembly, Display Lock
872843-1
N/A
1
10.
Bar, Support
10181-5213-002
N/A
1
11.
Bolt
MS35751-18
5306-00-108-9988
4
12.
Box, Stowage
889519-1
2540-01-499-0607
1
13.
Bracket, Antenna Base
RF292
5985-01-418-5247
1
14.
Bracket, Antenna, EPLRS
05A020ID
N/A
1
15.
Bracket, Mounting
889567-14
N/A
1
16.
Bracket, Mounting, Radio R/T
RF-5073VSM
5975-01-517-1766
1
17.
Bracket, Support
12460300
5340-01-456-6554
1
18.
Bracket, PLGR
986-0645-001
5975-01-375-1302
1
19.
Bracket, User Readout (URO)
A3006206
5340-01-386-7841
1
20.
Cable Assembly
A3206018-2
5995-01-392-6196
1
21.
Cable Assembly
A3206018-15
5995-01-392-6200
2
22.
Cable Assembly, Antenna, HF
10181-9824-020
5995-01-460-5697
1
23.
Cable Assembly, Antenna, HF
10564-3355-A004
N/A
1
24.
Cable Assembly, Antenna, EPLRS
SM-C-911480
5995-01-167-1269
1
25.
Cable Assembly, Antenna, PLGR
426-0141-050
6150-01-375-8662
1
26.
Cable Assembly, Control
10181-9823-020
N/A
1
27.
Cable Assembly, Ground
12480567-1
N/A
1
28.
Cable Assembly, Power
12480567-2
N/A
1
29.
Cable Assembly, Power
A3206017-3
5995-01-452-4309
1
30.
Cable Assembly, Power, EPLRS
A3004939
5995-01-198-0538
1
31.
Cable Assembly, Power, HF
10181-9826-020
5995-01-370-5985
1
32.
Cable Assembly, Power, PLGR
9728558-10
6150-01-375-8661
1
33.
Cable Assembly, Power, Speaker
10535-0708-A020
6150-01-519-6396
2
34.
Cable Assembly, Power, TAC-SAT
10570-0705-A021
N/A
1
35.
Cable Assembly, Speaker, R/T
10535-0707-A020
5995-01-514-6066
2
36.
Cable Assembly, TAC-SAT Antenna
10369-7211-020
N/A
1
37.
Cable Assembly, INC-EPUU
A3279383-3
5995-01-453-9171
1
38.
Cable Assembly, R/T
A3206019-3
5995-01-458-5334
1
39.
Cable Assembly, R/T
A3206127-3
5995-01-479-9739
1
40.
Cable Assembly, W3N
881336-1
5995-01-478-4913
1
4-4
TB 9-2320-387-35-4
MATERIAL REQUIRED BUT NOT INCLUDED IN KITS (Contd):
Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
ITEM
NO.
NOMENCLATURE
PART NUMBER
41.
Cable Assembly, W3P
881335-1
5995-01-478-4891
1
42.
Clamp, Loop
MS21333-69
5340-00-764-7051
5
43.
Clamp, Loop
MS21333-76
5340-00-724-7038
1
44.
Clamp, Loop
MS21333-104
5340-00-088-1254
1
45.
Clamp, Loop
MS21333-112
5340-00-057-3043
8
46.
Cover, Antenna Bracket
1018-5212-02
N/A
1
47.
Cover, Fuse
1209-9272
N/A
4
48.
CPU (Central Processing Unit)
881292-1
7021-01-474-3793
1
49.
Decal
12339060
7690-01-265-1135
1
50.
Decal
861868-2
N/A
1
51.
Display
881293-1
7025-01-475-0229
1
52.
Footrest Weldment
889567-21
N/A
1
53.
Fiber Rope Assembly
A3167672-1
4020-01-341-8795
2
54.
Gasket
A3013655-1
5330-01-205-2864
1
55.
Grommet, Nonmetallic
MS21266-1N
5325-00-960-2410
A/R
56.
Grommet, Nonmetallic
MS35489-19
5325-00-276-6091
1
57.
Grommet, Nonmetallic
MS35489-149
5325-01-309-7164
1
58.
Grommet, Nonmetallic
MS35489-150
5325-01-282-8245
1
59.
Grommet, Nonmetallic
12338098
5325-01-308-5424
1
60.
Grommet, Nonmetallic
2400
5325-01-289-7859
1
61.
Grommet, Nonmetallic
MS21266-2N
5325-00-074-3301
A/R
62.
Guard, Amp
872842-1
5935-01-487-2172
1
63.
Insert
ALS4-616-150
5325-01-483-7480
3
64.
Insert
12446871-1
5310-01-413-3276
6
65.
Insert
12446871-2
5310-01-411-3422
8
66.
Insert
12446871-8
5325-01-476-3041
5
67.
Insert
12446871-11
5325-01-505-3122
1
68.
Interface Unit, FFCS
A3206624
5895-01-469-6120
2
69.
Isolation Kit, CPU
872826-2
5340-01-481-5741
1
70.
Isolation Kit, Display
872870-1
5340-01-481-5757
1
71.
Lanyard
8925T5-7X19
4010-01-497-2675
1
72.
Left Rail Weldment
889567-12
N/A
1
73.
Locking Collar
Z52-0013-002
N/A
2
74.
Loudspeaker
10181-5180-01
5965-01-480-8784
2
75.
Master Control Station
A3206623
5895-01-469-3352
1
76.
Mount, Ramball
RAM-D-111U
5975-01-485-3615
1
77.
Mount, Resilient
MT-6146/VSQ-1
5340-01-167-8297
1
78.
Mount, TAC-SAT Radio
RF-5800H-V005
5820-01-512-2462
1
79.
Mounting Bracket, TAC-SAT Antenna
N/A
N/A
1
80.
Mounting Plate, Coupler
11080-0511-02
N/A
1
4-5
NSN
QTY.
TB 9-2320-387-35-4
MATERIAL REQUIRED BUT NOT INCLUDED IN KITS (Contd):
Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
ITEM
NO.
NOMENCLATURE
PART NUMBER
NSN
QTY.
81.
Nut
MS35649-2252
5310-00-997-1888
4
82.
Nut
MS35650-302
5310-00-934-9751
11
83.
Nut
MS51971-1
5310-00-903-5966
8
84.
Nut
MS51971-3
5310-00-913-8881
6
85.
Nut
13218E0320-293
5310-00-913-8881
8
86.
Nut
9418931
5310-01-187-7610
4
87.
Nut
9418892
5310-01-157-9819
10
88.
Nut
9417954
5310-00-931-8167
3
89.
Nut
9419143
5310-01-148-0240
2
90.
Nut
MS35649-63
5310-00-804-3859
5
91.
Nut, Lock
MS51943-31
5310-00-061-4650
4
92.
Nut, Lock
271175
5310-01-333-5245
6
93.
Nut, Nylon
10075-1397
N/A
2
94.
Nut, Plain-Assembled
271169
5310-00-124-9265
5
95.
Panel, Enclosure
12447141
2510-01-413-5993
1
96.
Right Rail Weldment
889567-22
N/A
1
97.
Rivet, Blind
12339355-1
5320-01-271-6357
2
98.
Rod
889567-16
N/A
1
99.
Screw, Cap
B1821BH025C063N
5305-01-457-8854
1
100.
Screw, Cap
B1821BH025C075N
5305-00-068-0508
7
101.
Screw, Cap
B1821BH025C088N
5305-00-071-2505
10
102.
Screw, Cap
B1821BH025C100N
5305-01-389-7984
13
103.
Screw, Cap
B1821BH025C150N
5305-00-071-2509
3
104.
Screw, Cap
B1821BH031C075N
5306-00-226-4825
4
105.
Screw, Cap
B1821BH031C100N
5306-00-226-4827
6
106.
Screw, Cap
B1821BH031C125N
5306-00-226-4829
2
107.
Screw, Cap
B1821BH031C150N
5305-00-226-4831
2
108.
Screw, Cap
B1821BH031F100N
5305-00-051-4076
2
109.
Screw, Cap
B1821BH031F125N
5305-00-051-4078
9
110.
Screw, Cap
B1821BH038C150N
5305-00-725-2317
4
111.
Screw, Cap
B1821BH038F175N
5305-00-269-3241
4
112.
Screw, Cap
B1821BH050C150N
5305-00-071-2069
4
113.
Screw, Machine
MS35190-287
5305-00-954-4295
2
114.
Screw, Machine
MS35190-291
5305-00-958-5247
2
115.
Screw, Machine
MS35206-230
5305-00-889-3000
5
116.
Screw, Machine
MS35207-263
5305-00-989-7434
2
117.
Screw, Machine
160046
5305-00-349-8534
1
118.
Screw, Cap
MS35207-265
5305-00-993-1848
4
119.
Screw, Cap
MS35207-269
5305-00-995-3441
6
120.
Screw, Cap
MS35207-270
5305-00-995-3440
4
4-6
TB 9-2320-387-35-4
MATERIAL REQUIRED BUT NOT INCLUDED IN KITS (Contd):
Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
ITEM
NO.
NOMENCLATURE
PART NUMBER
121.
Screw, Cap
MS35307-308
122.
Screw, Self-Tapping
123.
Screw, Self-Tapping
124.
NSN
QTY.
5305-00-207-8253
8
12342499-2
5305-01-264-5809
11
9416639
5305-01-197-2320
2
Screw, Self-Tapping
9421073
5305-01-162-8512
9
125.
Spacer
10181-5214-01
N/A
13
126.
Spacer
10705AL315C
5365-01-487-3145
4
127.
Spacer
5579297
5365-01-194-0761
3
128.
Spacer
92510A318
N/A
4
129.
Strap, Tiedown
MS3367-1-0
5975-00-984-6582
130.
Strap, Ground
7147-1167-3
5999-01-486-1606
2
131.
Support, Rack
889509-22
N/A
1
132.
Terminal Lug
7728777
5940-00-983-4067
1
133.
Terminal Lug
7728780
5940-01-035-4212
1
134.
Terminal Board
MS27212-3-8
5940-00-950-7782
1
135.
Terminal Board
12480570
N/A
1
136.
Terminal Board Cover
MS18029-3S-2
5940-01-280-9304
1
137.
Terminal Board Cover
12480569-2
N/A
1
138.
Terminal Board Cover
12480569-1
N/A
1
139.
Terminal Link
MS25226-6N-2
6150-01-167-9267
1
140.
Terminal Lug
MS20659-108
5940-00-115-2674
2
141.
Terminal Lug
MS20659-141
5940-00-113-9825
4
142.
Tubing, Convoluted
Z52-0013-001
N/A
1
143.
Tubing, Shrink
MS23053/4-302-0
5970-01-161-6796
A/R
144.
Washer
MS27183-8
5310-00-809-8546
6
145.
Washer
MS27183-10
5310-00-809-4058
19
146.
Washer
MS27183-47
5310-01-312-4959
2
147.
Washer
MS51412-23
5310-01-333-0060
2
148.
Washer
12338095
5310-01-208-7576
3
149.
Washer
2436161
5310-01-102-3270
9
150.
Washer
2436162
5310-01-119-1024
8
151.
Washer
2436164
5310-01-278-9555
6
152.
Washer, Lock
MS35307-365
5305-00-847-1159
8
153.
Washer, Lock
MS35338-41
5310-00-045-4007
5
154.
Washer, Lock
MS35338-43
5310-00-045-3296
24
155.
Washer, Lock
MS35338-44
5310-00-582-5965
5
156.
Washer, Lock
MS35338-45
5310-00-407-9566
5
157.
Washer, Lock
MS35338-48
5310-00-584-5272
3
158.
Washer, Lock
MS35338-141
5310-00-984-7042
6
159.
Washer, Lock
MS45904-71
5310-00-947-6980
28
160.
Washer, Lock
MS45904-76
5310-00-061-1258
12
4-7
A/R
TB 9-2320-387-35-4
MATERIAL REQUIRED BUT NOT INCLUDED IN KITS (Contd):
Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
ITEM
NO.
NOMENCLATURE
PART NUMBER
161.
Washer, Lock
120217
5310-01-279-8319
1
162.
Wingnut
MS51553-420
5310-01-384-2546
4
163.
Wire Assembly, Fuse (12V)
12480568-2
N/A
1
164.
Wire Assembly, Fuse (24V)
12480568-1
165.
Wire, Braided
AA59569F30T0375
6145-00-191-8402
A/R
166.
Wire, Lock
MS20995C32
9505-00-293-4208
A/R
4-8
NSN
N/A
QTY.
3
TB 9-2320-387-35-4
CHAPTER 5
INSTALLATION PROCEDURES
Section I. SCOPE
This chapter provides instructions for installation of the following C4ISR equipment:
• Single Channel Ground and Airborne Radio System (SINCGARS)
• Precision Lightweight Global Positioning System Receiver (PLGR)
• Enhanced Position Location Reporting System (EPLRS)
• Vehicular Intercommunications Set (VIS)
• Force XXI Battle Command, Brigade-and-Below (FBCB2)
• HF 150 Watt Radio
• TAC-SAT Radio
• Additional terminal boards in the vehicle
When installing C4ISR equipment, be sure to read and follow instructions and illustrations carefully.
Section II. INSTALLATION OF TERMINAL BOARDS
Use the following procedure to install additional terminal boards to provide adequate power connections.
Vehicles must have dual-voltage alternators installed in order to have both 12V and 24V terminal boards
installed.
Section III. CAB ENCLOSURE PANEL, TERMINAL BOARD, AND COVER MODIFICATION
NOTE
• Late model M1114 vehicles come with cab enclosure panel and
24V terminal board. For early model M1114 vehicles, perform
sections III through VI. For late model M1114 vehicles
begin, at section VII.
• For vehicles without cab enclosure panel, begin with step 3-1.
• For vehicles with cab enclosure panel, begin with step 3-3.
• All dimensions are in inches.
3-1. Place enclosure panel (3) in position. Locate, mark, and drill five 0.159-in. diameter holes marked A
and B in B-beam (1) and battery box (2).
3-2. Enlarge two lower mounting holes marked A to 0.390-in. diameter, and install two inserts (4) in
battery box (2).
1
B
~
2
B
B
3
A
A
4
3. ENCLOSURE PANEL – 12447141 – QTY. 1
4. INSERT – 12446871-2 – QTY. 2
Figure 5-1.
5-1
TB 9-2320-387-35-4
NOTE
Do not install cab enclosure panel.
3-3. Locate, mark, and drill three 0.156-in. diameter holes marked A in cab enclosure panel (1).
3-4. Locate, mark, and drill two 0.196-in. diameter holes marked B in cab enclosure panel (1).
3-5. Locate, mark, and drill two 0.281-in. diameter holes marked C in cab enclosure
panel (1).
0
3.9
0
3.0
3.17
0
3.0
1.33
1
A
A
A
5.75
B
B
C
C
2.375
2.375
Figure 5-2.
5-2
TB 9-2320-387-35-4
NOTE
Perform steps 3-6 through 3-8 only if supplemental heater is
installed.
3-6. Locate, mark, and cut corner of cab enclosure panel (1).
3-7. Locate, mark, and drill 0.154-in. diameter hole (5) in cab enclosure panel (1).
1.750
5
.50
2.375
1
Figure 5-3.
3-8. Install grommet material (6) on cab enclosure panel (1) with RTV compound.
1
6
6. GROMMET MATERIAL – MS21266-1N – QTY. A/R
Figure 5-4.
5-3
TB 9-2320-387-35-4
CAUTION
Do not cut raised sections of terminal board. Terminal board is not
usable if cut on raised section.
3-9. Measure and cut terminal board (6) in two places (7). Remove burrs and sharp edges.
3-10. Install five nut sleeves (10) in terminal board covers (8), (9), and (11), and secure with five
snaprings (12).
8
24V REF
6
9
10
12V REF
11
6.624
7
3.624
12
Figure 5-5.
6.
8.
9.
11.
TERMINAL
TERMINAL
TERMINAL
TERMINAL
BOARD
BOARD
BOARD
BOARD
Figure 5-6.
– MS27212-3-8 – QTY. 1
COVER – 12480569-1 – QTY. 1
COVER – 12480569-2 – QTY. 1
COVER – MS18029-3S-2 – QTY. 1
5-4
TB 9-2320-387-35-4
Section IV. B-BEAM PREPARATION
Locate, mark, and drill four 0.159-in. diameter holes (2) in B-beam (1).
1.78
1.78
1.375
1.78
5.75
~
1
2
1. FUSE COVER – 1209-9272 – QTY. 3 OR 4
2. SELF-TAPPING SCREW – 12342499-2 – QTY. 3 OR 4
Figure 5-7.
5-5
TB 9-2320-387-35-4
Section V. ASSEMBLY OF CAB ENCLOSURE PANEL
NOTE
• For 12V terminal board installation on models with rifle mount
bracket shown in figure 5-8, perform steps 5-1 through 5-3.
• If not installing 12V terminal board, begin with step 5-4.
5-1. Remove lower rifle mount bracket (1) from B-beam. (Refer to TM 9-2320-387-24.)
5-2. Locate, mark, and drill two 0.159-in. diameter holes marked A in lower rifle mount bracket (1).
Install 12V terminal board (4) on lower rifle mount bracket (1) with two screws (2), lockwashers (3),
and nuts (5).
5-3. Install lower rifle mount bracket (1) on B-beam. (Refer to TM 9-2320-387-24.)
2
3
4
5
1.35
A
1.50
1
3.00
A
2. SCREW – MS35206-230 – QTY. 2
3. LOCKWASHER – MS35338-41 – QTY. 2
5. NUT– MS35649-63 – QTY. 2
Figure 5-8.
5-6
TB 9-2320-387-35-4
5-4. Install 24V terminal board (9) on enclosure panel (6) with three screws (2), lockwashers (3), and
nuts (5).
5-5. Enlarge two holes marked A in terminal board (7) to 0.196 in., and secure terminal board (7) to
panel (6) with two rivets (8).
5-6. Install three existing relays (11) in holes (12) on panel (6) with four existing screws (14),
washers (13), and locknuts (10).
6
2
3
A
14
A
13
7
9
8
12
10
11
2.
3.
5.
7.
8.
10.
5
SCREW – MS35206-230 – QTY. 3
LOCKWASHER – MS35338-41 – QTY. 3
NUT – MS35649-63 – QTY. 3
TERMINAL BOARD – 12480570 – QTY. 1
BLIND RIVET – 12339355-1 – QTY. 2
LOCKNUT – MS51943-31 – QTY. 4
Figure 5-9.
5-7
TB 9-2320-387-35-4
Section VI. FINAL ASSEMBLY, TERMINAL BOARD WIRING, AND TERMINAL LINK
NOTE
• Refer to figure 5-10 for wiring overview.
• Perform steps 6-1 and 6-2 if hole and grommet do not exist in
battery box.
• If installing 24V terminal board only, begin with step 6-6.
6-1. Locate, mark, and drill 2.00-in. diameter hole (3) in upper right corner of rear wall of battery box.
6-2. Install grommet (4) in hole (3).
6-3. Secure terminal link (8) and fuse wire (7) to 12V terminal board (1) with two locknuts (6), and
install cover (5).
6-4. Route wire (2) through battery box hole (3).
3 X 24V FUSES, 25 AMP
EXISTING VEHICLE POWER STUD
POSITIVE FUSE WIRES
EXISTING VEHICLE BUSS BAR
24V BUSS BAR
GROUND WIRE
EXISTING VEHICLE SHUNT
POWER WIRE
GROUND STRAP
12V BUSS BAR
GROUND SCREW
12V FUSE, 15 AMP
VEHICLE BATTERY
VEHICLE BATTERY
Figure 5-10.
2
1
4.
6.
7.
8.
4
GROMMET – 2400 – QTY. 1
LOCKNUT – 271175 – QTY. 2
FUSE WIRE ASSEMBLY (12V) – 12480568-2 – QTY. 1
TERMINAL LINK – MS25226-6N-2 – QTY. 1
8
7
Figure 5-11.
5-8
3
6
5
TB 9-2320-387-35-4
6-5. Connect wire (2) to existing positive 12V battery terminal end (10) with existing screw (9) and
nut (11).
9
10
11
2
Figure 5-12.
6-6. Position cab enclosure panel (12) in rear floor pan (20) and rear of B-beam (21). Do not secure cab
enclosure panel (12) at this time.
6-7. Route ground cable (16) through battery box hole (6).
6-8. Secure terminal lug (14) on center terminal of terminal board (13) with nut (15), and secure
terminal lug (19) on shunt (18) with existing screw (17).
6-9. Install four additional plain-assembled nuts (15) on terminal board (13).
12
13
14
15
6
16
17
18
~
~
19
21
20
15. PLAIN-ASSEMBLED NUT – 271169 – QTY. 5
16. GROUND CABLE ASSEMBLY – 12480567-1 – QTY. 1
Figure 5-13.
5-9
TB 9-2320-387-35-4
6-10. Route 24V power cable (27) through hole (6) and install 24V power cable terminal lug (23) on
inboard stud (22) of terminal board (28). Do not secure 24V power cable terminal lug (23) at this
time.
6-11. Secure three fuse wires (25) and 24V power cable terminal lug (23) to inboard terminal board
stud (22) with locknut (26).
6-12. Secure three remaining fuse wires (24) to corresponding studs on 24V terminal board (28) with
three locknuts (26).
22
24
22
28
23
25
26
6
27
24. FUSE WIRE ASSEMBLY (24V) – 12480568-1 – QTY. 3
26. LOCKNUT – 271175 – QTY. 4
27. POWER CABLE ASSEMBLY – 12480567-2 – QTY. 1
Figure 5-14.
5-10
TB 9-2320-387-35-4
NOTE
For vehicles with new enclosure panel, begin with step 6-14.
6-13. Install cab enclosure panel (12). (Refer to TM 9-2320-387-24.)
6-14. Secure cab enclosure panel (12) to B-beam (21) with three self-tapping screws (29).
6-15. Secure cab enclosure panel (12) to battery box (33) with two capscrews (30), lockwashers (31), and
washers (32).
21
12
29
~
33
30
32
31
29.
30.
31.
32.
SELF-TAPPING SCREW – 12342499-2 – QTY. 3
CAPSCREW – B1821BH025C075N – QTY. 2
LOCKWASHER – MS35338-48 – QTY. 2
WASHER – MS51412-23 – QTY. 2
Figure 5-15.
5-11
TB 9-2320-387-35-4
6-16. Secure three 24V fusewire assemblies (24) and one 12V fusewire assembly (7) to B-beam (21) with
four self-tapping screws (29).
NOTE
For models equipped with power stud, perform step 6-17.
Otherwise, proceed to step 6-18.
6-17. Secure 24V terminal board power wire terminal lug (27) to power stud (37) with lockwasher (31)
and existing nut (36).
6-18. Secure 24V terminal board power wire terminal lug (27) to terminal board (35) with lockwasher (31)
and existing nut (36).
6-19. Install decal (34) on B-beam (21).
6-20. If previously removed, install right-hand rear fixed door. (Refer to TM 9-2320-387-24.)
6-21. Install batteries. (Refer to TM 9-2320-387-24.)
21
24
34
~
7
29
27
35
27
37
36
31
36
29. SELF-TAPPING SCREW – 12342499-2 – QTY. 4
31. LOCKWASHER – MS35338-48 – QTY. 1
34. DECAL – 12339060 – QTY. 1
Figure 5-16.
5-12
31
TB 9-2320-387-35-4
Section VII. INTEGRATED RACK INSTALLATION
NOTE
Perform steps 7-1 and 7-2 if blast shield is installed. Perform
steps 7-3 and 7-4 if blast shield is not installed.
7-1. Using rack support (1) as template, locate, mark, and drill three 0.375-in. diameter holes (3) in
blast shield (4) and through tunnel (5).
7-2. Install three inserts (2) in holes (3) in blast shield (4).
1
~
5
2
4
3
1. RACK SUPPORT – 889509-22 – QTY. 1
2. INSERT – ALS4-616-150 – QTY. 3
Figure 5-17.
7-3. Using rack support (1) as template, locate, mark, and drill three 0.375-in. diameter holes (3) in
tunnel (5).
7-4. Install three inserts (2) in holes (3) in tunnel (5).
1
~
5
2
3
Figure 5-18.
5-13
TB 9-2320-387-35-4
7-5. Locate, mark, and drill 0.531-in. diameter hole (8) in integrated rack (6).
7-6. Install insert (7) in hole (8) in integrated rack (6).
6
7
8
5.6
2
2.94
8. INSERT – 12446871-11 – QTY. 1
Figure 5-19.
7-7. Install keyboard stowage box (9) on integrated rack (6) using four existing captive screws (10).
6
10
9
9. KEYBOARD STOWAGE BOX – 889519-1 – QTY. 1
Figure 5-20.
5-14
TB 9-2320-387-35-4
7-8. Install W3 cable (16) to Serial Interface Adapter Device (SIAD) (17).
7-9. Install W3N cable (14) to SIAD (17).
7-10. Install W3P cable (15) to SIAD (17).
7-11. Install SIAD (17) on integrated rack (6) using two screws (13), lockwashers (12), and washers (11).
6
11.
12.
13.
14.
15.
16.
17.
WASHER – MS27183-47 – QTY. 2
LOCKWASHER – MS35338-43 – QTY. 2
SCREW – MS35207-263 – QTY. 2
W3N CABLE – 881336-1 – QTY. 1
W3P CABLE – 881335-1 – QTY. 1
W3 CABLE P/O – 881331-1 – QTY. 1
SIAD – 881331-1 – QTY. 1
11
12
13
17
14
16
15
Figure 5-21.
7-12. Fabricate ground strap (23) from 8.00-in. length of braided wire and two terminal lugs.
NOTE
• Perform step 7-13 if blast shield is installed.
• Perform step 7-14 if blast shield is not installed.
7-13. Install rack support (1) on blast shield (4) and tunnel (5) with three capscrews (21), lockwashers (19),
washers (20), and ground strap (23), and three existing capscrews (18), lockwashers (19), washers (20),
and spacers (22). Do not tighten capscrews (21) and (18) at this time.
18
20
19
21
19
20
1
18.
19.
20.
21.
22.
23.
20
19
20
21
19
19
20
~
CAPSCREW – B1821BH025C150N – QTY. 3
LOCKWASHER – MS35338-44 – QTY. 6
WASHER – 2436161 – QTY. 6
CAPSCREW – B1821BH025C100N – QTY. 3
SPACER – 5579297 – QTY. 3
GROUND STRAP
• BRAIDED WIRE – AA59569F30T0375 – QTY. A/R
• TERMINAL LUG – MS20659-141 – QTY. 2
19
5
4
Figure 5-22.
5-15
23
20
22
TB 9-2320-387-35-4
NOTE
Blast shield may not be present in steps 7-14 through 7-22.
7-14. Install rack support (1) on tunnel (5) with three capscrews (21), lockwashers (19), washers (20), and
ground strap (23), and three existing capscrews (18), lockwashers (19), washers (20), and
spacers (22). Do not tighten capscrews (21) and (18) at this time.
18 19
20
21
18 19
20
18
19
20
21
21
19
19
20
20
19
20
1
5
~
22
22
23
22
Figure 5-23.
5-16
TB 9-2320-387-35-4
7-15. Position integrated rack (6) on rack support (1).
7-16. Align integrated rack (6) top mounting holes (24) with holes (25) in dash panel (26).
7-17. Remove integrated rack (6) from rack support (1).
7-18. Tighten three capscrews (18) and three capscrews (21) securing rack support (1) to tunnel (5).
24
6
25
26
~
5
~
1
18
21
Figure 5-24.
5-17
TB 9-2320-387-35-4
7-19. Position integrated rack (6) on rack support (1).
7-20. Install integrated rack (6) on rack support (1) using five capscrews (27), lockwashers (28), and
washers (29), and one capscrew (30), lockwasher (28), and washer (29).
6
27
30
28
29
28
29
27.
28.
29.
30.
CAPSCREW – B1821BH025C088N – QTY. 5
LOCKWASHER – MS35338-44 – QTY. 6
WASHER – MS27183-10 – QTY. 6
CAPSCREW – B1821BH025C063N – QTY. 1
1
Figure 5-25.
7-21. Fabricate ground strap (35) from 8-in. length of braided wire and two terminal lugs.
NOTE
Remove paint from vicinity of integrated rack mounting hole
before performing step 7-22. Apply antiseize compound as
required.
7-22. Attach integrated rack (6) to dash panel (34) using two capscrews (31), lockwashers (32),
washers (33), and ground strap (35).
31 32
31 32 33
33
6
34
~
35
31.
32.
33.
35.
CAPSCREW – B1821BH025C100N – QTY. 2
LOCKWASHER – MS35338-44 – QTY. 2
WASHER – 2436161 – QTY. 2
GROUND STRAP
• BRAIDED WIRE – AA59569F30T0375 – QTY. A/R
• TERMINAL LUG – MS20659-141 – QTY. 2
Figure 5-26.
5-18
TB 9-2320-387-35-4
Section VIII. SINCGARS MOUNTING TRAY, AMP GUARD, AND
FBCB2 COMPONENTS INSTALLATION
8-1. Install ramball mount (6) on integrated rack (8) with two screws (5), and one capscrew (12),
lockwasher (11), lanyard (10), and washer (9).
8-2. Install display isolation kit (2) on display unit mount (1) with four bolts (13), spacers (14), one
lanyard (10), and four wingnuts (15).
8-3. Install display unit (3) on display isolation kit (2) with four screws (4).
8-4. Install display unit mount (1) on ramball mount (6).
8-5. Install ground strap (7) on display ground stud (18) with existing lockwasher (17) and wingnut (16).
15
10
1
14
18
2
17
7
13
16
3
4
12
5
11
10
1.
2.
3.
5.
6.
9.
10.
11.
12.
13.
14.
15.
9
DISPLAY LOCK ASSEMBLY – 872843-1 – QTY. 1
DISPLAY ISOLATION KIT – 872870-1 – QTY. 1
DISPLAY – 881293-1 – QTY. 1
SCREW – MS35190-291 – QTY. 2
RAMBALL MOUNT – RAM-D-111U – QTY. 1
WASHER – 2436161 – QTY. 1
LANYARD – 8925T5-7X19 – QTY. 1
LOCKWASHER – MS35338-44 – QTY. 1
CAPSCREW – B1821AH025C100N – QTY. 1
BOLT – MS35751-18 – QTY. 4
SPACER – 10705AL315C – QTY. 4
WINGNUT – MS51553-420 – QTY. 4
6
7
8
Figure 5-27.
5-19
TB 9-2320-387-35-4
8-6. Place mounting bracket (25) on two existing studs (19).
8-7. Attach rod (22) to left rail weldment (24) and right rail weldment (21) with two screws (20).
8-8. Place rail assembly on two right-hand studs (19) on integrated rack (7) and attach left rail
weldment (24) to integrated rack (7) with three capscrews (23).
7
19
23
20
19
25
24
19.
21.
22.
23.
24.
25.
23
20
22
19
SCREW – MS35190-287 – QTY. 2
RIGHT RAIL WELDMENT – 889567-22 – QTY. 1
ROD – 889567-16 – QTY. 1
CAPSCREW – B1821BH025C075N – QTY. 3
LEFT RAIL WELDMENT – 889567-12 – QTY. 1
MOUNTING BRACKET – 889567-14 – QTY. 1
Figure 5-28.
5-20
21
TB 9-2320-387-35-4
8-9. Install CPU isolation kit (33) on integrated rack (7) with four existing studs (19),
washers (35), lockwashers (36), and nuts (37).
8-10. Install CPU (26) on CPU isolation kit (33) with two existing fastener guards (34).
8-11. Install existing ground strap (28) on stud (27) on CPU (26) with existing wingnut (29),
lockwasher (30), and washer (31).
8-12. Connect W3 cable (42) from Serial Interface Adapter Device (SIAD) (44) to J3 connector (39) on
FBCB2 processor (26).
8-13. Connect W1 cable (41) to J1 connector (40) on FBCB2 processor (26).
8-14. Connect W2 cable (43) from J4 connector (38) on FBCB2 processor (26) to FBCB2 display unit (32).
8-15. Route W3N cable (45) from SIAD (44) to integrated rack (7).
26
31
30
29
28
26
27
33
37
36
35
32
34
45
34
44
7
26
38
43
39
40
42
26.
33.
35.
36.
37.
41
CPU – 881292-1 – QTY. 1
CPU ISOLATION KIT – 872826-2 – QTY. 1
WASHER – MS27183-10 – QTY. 4
LOCKWASHER – MS35338-44 – QTY. 4
NUT – MS35649-2252 – QTY. 4
28
Figure 5-29.
5-21
19
TB 9-2320-387-35-4
8-16. Remove paint from four mounting holes (51) on integrated rack (7). Apply antisieze compound as
required.
8-17. Remove paint from four mounting holes (50) on MT-6352/VRC mounting base (49). Apply antisieze
compound as required.
NOTE
Two lockwashers and nuts are used on driver’s side screws only.
8-18. Mount MT-6352/VRC mounting base (49) and amp guard (53) on integrated rack (7) with two
screws (46), four lockwashers (47), two nuts (52). Secure mount MT-6352/VRC mounting base (49)
on integrated rack (7) with two capscrews (48) and two lockwashers (47).
8-19. Place warning decal (54) on amp guard (53).
47
48
46
49
53
54
50
7
53
47
52
51
46. CAPSCREW – B1821BH031F125N – QTY. 2
47. LOCKWASHER – MS45904-72 – QTY. 6
48. CAPSCREW – B1821BH031F100N – QTY. 2
49. MOUNTING BASE, MT-6352/VRC – A3013367-1 – QTY. 1
52. NUT – 9418892 – QTY. 2
53. AMP GUARD – 872842-1 – QTY. 1
54. DECAL – 861868-2 – QTY. 1
Figure 5-30.
5-22
TB 9-2320-387-35-4
8-20. Insert weldment (58) into grooves of integrated rack (7).
8-21. Install Full Function Control Station (FFCS) (59) on weldment (58) using two existing
studs (57), two washers (56), two washers (55), lockwashers (54), and nuts (52).
52
55
59
54
56
7
~
58
57
52.
54.
55.
56.
59.
NUT – 9418892 – QTY. 2
LOCKWASHER – MS35338-45 – QTY. 2
WASHER – 2436162 – QTY. 2
WASHER – 2436164 – QTY. 2
FFCS – A3206624 – QTY. 1
Figure 5-31.
5-23
TB 9-2320-387-35-4
8-22. Insert footrest weldment (62) into grooves of right rail weldment (21) and left rail weldment (24).
8-23. Insert quick-release pin (61) through hole (60) in footrest weldment (62), left rail weldment (24),
and integrated rack (7).
61
60
62
7
~
24
~
21
62. FOOTREST WELDMENT – 889567-21 – QTY. 1
Figure 5-32.
5-24
TB 9-2320-387-35-4
8-24. Install master control station (65) on integrated rack (7) using existing stud (64), washer (56),
washer (55), lockwasher (54), and nut (63), and capscrew (46), lockwasher (54), washer (55), and
washer (56).
46
63
54
54
55
55
56
56
65
7
64
46.
54.
55.
56.
63.
65.
CAPSCREW – B1821BH031F125N – QTY. 1
LOCKWASHER – MS35338-45 – QTY. 2
WASHER – 2436162 – QTY. 2
WASHER – 2436164 – QTY. 2
NUT – 9417954 – QTY. 1
MASTER CONTROL STATION – A3206623 – QTY. 1
Figure 5-33.
5-25
TB 9-2320-387-35-4
Section IX. HF 150 WATT RADIO ANTENNA BRACKET AND ANTENNA INSTALLATION
NOTE
Do not tighten screws at this time.
9-1. Attach antenna mounting bracket (5) to rear wall of right rear wheelhouse (3) with three capscrews
(6), six lockwashers (2), three aluminum spacers (4), and nuts (1).
9-2. Temporarily install support bar (7) on antenna mounting bracket (5).
9-3. Using support bar (7) as template, locate and mark two hole locations (8). Remove support bar (7).
9-4. Drill two 0.281-in. diameter holes (8) in right rear wheelhouse (3).
NOTE
Do not tighten bolts at this time.
9-5. Attach support bar (7) to antenna mounting bracket (5) with two capscrews (13), lockwashers (10),
and washers (11).
NOTE
Do not tighten capscrews at this time.
9-6. Attach support bar (7) to right rear wheelhouse (3) with two capscrews (12), washers (11),
spacers (4), lockwashers (10), and nuts (9).
9-7. Tighten top two capscrews (6) securing antenna mounting bracket (5) to right rear wheelhouse (3).
9-8. Tighten two capscrews (13) securing support bar (7) to antenna mounting bracket (5).
9-9. Tighten two capscrews (12) securing support bar (7) to right rear wheelhouse (3).
1
2
3
4
5
2
6
1.
2.
4.
5.
6.
NUT – 9418892 – QTY. 3
LOCKWASHER – MS45904-72 – QTY. 6
SPACER – 10181-5214-01 – QTY. 3
MOUNTING BRACKET, ANTENNA BASE – RF292 – QTY. 1
CAPSCREW – B1821BH031F125N – QTY. 3
Figure 5-34.
5-26
TB 9-2320-387-35-4
3
~
7
5
~
8
Figure 5-35.
3
9
~
10
5
4
11
7
11
4.
7.
9.
10.
SPACER – 10181-5214-01 – QTY. 2
BAR, SUPPORT – 10181-5213-002 – QTY. 1
NUT – 9419143 – QTY. 2
LOCKWASHER – MS45904-72 – QTY. 4
13
10
11. WASHER – MS27183-10 – QTY. 6
12. CAPSCREW – B1821BH025C100N – QTY. 2
13. CAPSCREW – B1821BH025C088N – QTY. 2
Figure 5-36.
5-27
12
TB 9-2320-387-35-4
9-10. Attach ground strap (17) to antenna base (16) and position antenna base (16) on antenna mounting
bracket (5).
9-11. Install terminal lug (18) on ground strap (17).
9-12. Remove bottom capscrew (6) and lockwashers (2) from antenna mounting bracket (5). Secure
antenna ground strap (17) to right rear wheelhouse (3) and antenna mounting bracket (5) with
existing capscrew (6), three lockwashers (2), and nut (1).
9-13. Secure antenna base (16) to antenna mounting bracket (5) with four capscrews (14) and
lockwashers (15).
14
15
16
3
1
~
2
5
17
2.
14.
15.
16.
18.
LOCKWASHER – MS45904-72 – QTY. 1
CAPSCREW – B1821BH038F175N – QTY. 4
LOCKWASHER – MS45904-76 – QTY. 4
HF ANTENNA – 4245 – QTY. 1
TERMINAL LUG – MS20659-108 – QTY. 1
2
6
18
2
Figure 5-37.
NOTE
Ensure antenna adapter tilts fore and aft of vehicle after
tightening.
9-14. Install antenna adapter (19) on antenna base (16) by screwing on until tight.
9-15. Secure with existing clamp (20).
19
16
20
19. ANTENNA ADAPTER – RF-1980-AT001 – QTY. 1
Figure 5-38.
5-28
TB 9-2320-387-35-4
9-16. Install cover plate (22) on antenna mounting bracket (5) with three screws (13), washers (11), and
lockwashers (21).
21
13
5
11
22
~
3
11.
13.
21.
22.
WASHER – MS27183-10 – QTY. 3
CAPSCREW – B1821BH025C088N – QTY. 3
LOCKWASHER – MS35338-44 – QTY. 3
COVER, ANTENNA BRACKET – 1018-5212-02 – QTY. 1
Figure 5-39.
5-29
TB 9-2320-387-35-4
Section X. SINCGARS ANTENNA INSTALLATION
10-1. Install antenna (3) on right rear cargo shell (5) with gasket (4), four capscrews (2), eight
lockwashers (1), and four nuts (6).
2
3
1
4
5
~
1
6
1.
2.
3.
4.
6.
LOCKWASHER – MS45904-76 – QTY. 8
CAPSCREW – MS35307-365 – QTY. 4
ANTENNA – A3017889-2 – QTY. 1
GASKET – A3013655-1 – QTY. 1
NUT – 9418931 – QTY. 4
Figure 5-40.
5-30
TB 9-2320-387-35-4
10-2. Attach upper antenna element (7) to lower antenna element (9).
10-3. Attach antenna assembly to antenna base (3).
10-4. Attach fiber rope assembly (8) to upper antenna element (7).
10-5. Secure lower antenna element (9) to antenna base (3) with lock wire (10).
7
7
8
9
3
9
10
3
7.
8.
9.
10.
UPPER ANTENNA ELEMENT – A3017901-2 – QTY. 1
FIBER ROPE ASSEMBLY – A3167672-1 – QTY. 1
LOWER ANTENNA ELEMENT – A3018230-1 – QTY. 1
LOCK WIRE – MS20995C32 – QTY. A/R
Figure 5-41.
5-31
TB 9-2320-387-35-4
Section XI. REAR SINCGARS ANTENNA INSTALLATION
NOTE
This procedure applies to vehicles without existing antennas. For
vehicles with existing antennas, remove all control cables. (Refer
to TM 9-2320-387-24.)
11-1. Using antenna mounting bracket (3) as template, locate, mark, and drill one 1.375-in. diameter
hole (4) in left rear wall (2).
11-2. Locate, mark, and drill three 0.343-in. diameter holes (1) in rear wall (2).
11-3. Remove paint from vicinity of three holes (1) and three matching holes in antenna mounting
bracket (3).
11-4. Apply anti-seize compound to vicinity of three holes (1) and rear of antenna mounting bracket (3).
1
2
3
4
1
3. ANTENNA MOUNTING BRACKET – A3014546-1 – QTY. 1
Figure 5-42.
5-32
TB 9-2320-387-35-4
11-5. Install grommet (8) in hole of rear wall (2).
11-6. Position antenna (15) and gasket (7) on antenna mounting bracket (3) and route existing ground
strap (13) through antenna mounting bracket (3).
11-7. Install antenna (15) on antenna mounting bracket (3) with four capscrews (5), eight
lockwashers (6), and four nuts (14).
11-8. Install antenna mounting bracket (3) on rear wall (2) with two capscrews (12), lockwashers (6),
washers (9), and nuts (10).
11-9. Remove old terminal lug, and install new terminal lug (11) on ground strap (13). Install ground
strap (13) and antenna mounting bracket (3) on rear wall (2) with capscrew (12), lockwasher (6),
washer (9), and nut (10).
5
6
15
2
9
7
6
8
~
14
13
3
12
5.
6.
7.
8.
9.
10.
11.
12.
14.
15.
11
6
CAPSCREW – MS35307-365 – QTY. 4
LOCKWASHER – MS45904-72 – QTY. 11
GASKET – A3013655-1 – QTY. 1
GROMMET – 12338098 – QTY. 1
WASHER – 12338095 – QTY. 3
NUT – 9418892 – QTY. 3
TERMINAL LUG – MS20659-108 – QTY. 1
CAPSCREW – B1821BH031F125N – QTY. 3
NUT – 13218E0320-293 – QTY. 4
ANTENNA – A3017889-2 – QTY. 2
Figure 5-43.
5-33
10
TB 9-2320-387-35-4
11-10. Attach upper antenna element (16) to lower antenna element (18).
11-11. Attach antenna assembly to antenna base (7).
11-12. Attach fiber rope assembly (17) to upper antenna element (16).
11-13. Secure lower antenna element (18) to antenna base (7) with lockwire (19).
16
16
17
18
7
18
19
7
16.
17.
18.
19.
UPPER ANTENNA ELEMENT – A3017901-2 – QTY. 1
FIBER ROPE ASSEMBLY – A3167672-1 – QTY. 1
LOWER ANTENNA ELEMENT – A3018230-1 – QTY. 1
LOCKWIRE – MS20995C32 – QTY. A/R
Figure 5-44.
5-34
TB 9-2320-387-35-4
Section XII. EPLRS ANTENNA AND BRACKET INSTALLATION
12-1. Remove six capscrews (6), lockwashers (5), and washers (4) from A/C louvres (2).
12-2. Enlarge holes (3) to 0.375 in. diameter.
12-3. Install EPLRS antenna bracket (1) on A/C louvres (2) with six capscrews (6), lockwashers (5), and
washers (4).
1
~
6
5
4
2
~
3
1.
4.
5.
6.
EPLRS ANTENNA BRACKET – 05A020ID – QTY. 1
WASHER – MS27183-8 – QTY. 6
LOCKWASHER – MS35338-43 – QTY. 6
CAPSCREW – MS35207-269 – QTY. 6
Figure 5-45.
5-35
TB 9-2320-387-35-4
12-4. Install EPLRS antenna (9) and gasket (10) on bracket (1) with four capscrews (7),
eight lockwashers (8), and four nuts (11).
7
8
9
10
1
8
11
7.
8.
9.
10.
11.
CAPSCREW – B1821BH038C150N – QTY. 4
LOCKWASHER – MS45904-76 – QTY. 8
ANTENNA – A3005031 – QTY. 1
GASKET – A3013655-1 – QTY. 1
NUT – 13218E0320-293 – QTY. 4
Figure 5-46.
5-36
TB 9-2320-387-35-4
Section XIII. INSTALLATION OF TAC-SAT BRACKET AND ANTENNA
NOTE
• Entire area under antenna base must be free of paint.
• Do not remove any excess paint. Spot paint as necessary.
13-1. Using TAC-SAT antenna base as template, sketch outline on mounting bracket (2). Remove all
paint within this area (1) on mounting bracket.
1
2
~
2. TAC-SAT ANTENNA MOUNTING BRACKET – N/A – QTY. 1
Figure 5-47.
5-37
TB 9-2320-387-35-4
13-2. Position TAC-SAT antenna mount 1.00 in. from left edge of cargo door. Locate, mark, and drill
0.375-in. diameter hole (3) in cargo door (4).
13-3. Using TAC-SAT antenna bracket as template, locate, mark, and drill remaining three holes (5) in
cargo door (4).
NOTE
Align hole in cargo door with rear hole in bracket.
13-4. Locate, mark, and drill one 0.75-in. diameter hole (6) in cargo door (4).
3
4
~
6
5
Figure 5-48.
5-38
TB 9-2320-387-35-4
NOTE
Remove any footman loop that interferes with installation of
antenna bracket.
13-5. Install TAC-SAT antenna mounting bracket (2) on cargo door (4) with four capscrews (7), eight
lockwashers (8), and four locknuts (9).
7
8
2
8
9
~
4
7. CAPSCREW – B1821BH050C150N – QTY. 4
8. LOCKWASHER – MS35338-43 – QTY. 8
9. NUT – MS35650-302 – QTY. 4
Figure 5-49.
5-39
TB 9-2320-387-35-4
13-6. Install antenna (10) on antenna bracket (2) with four capscrews (11), eight lockwashers (12), and
four nuts (13).
10
11
12
2
13
11. CAPSCREW – MS35207-270 – QTY. 4
12. LOCKWASHER – MS35338-43 – QTY. 8
13. NUT – MS35650-302 – QTY. 4
Figure 5-50.
5-40
TB 9-2320-387-35-4
Section XIV. EPLRS MOUNTING INSTALLATION
14-1. Remove paint from vicinity of four mounting holes (1) on bottom of MT-6146/VSQ-1 mount (2).
1
2
2. RESILIENT MOUNT – MT-6146/VSQ-1 – QTY. 1
Figure 5-51.
5-41
TB 9-2320-387-35-4
14-2. Using EPLRS mount (2) as template, locate, mark, and drill four 0.531-in. diameter holes (7) in
right rear wheelhouse (6).
14-3. Install four inserts (5) in right rear wheelhouse (6).
14-4. Install EPLRS mount (2) on right rear wheelhouse (6) with four capscrews (3) and lockwashers (4).
3
4
2
5
6
~
7
3. CAPSCREW – B1821BH031C075N – QTY. 4
4. LOCKWASHER – MS45904-72 – QTY. 8
5. INSERT – 12446871-1 – QTY. 4
Figure 5-52.
5-42
TB 9-2320-387-35-4
Section XV. HF 150 WATT RADIO MOUNTING BRACKET INSTALLATION
15-1. Using HF 150 watt radio mounting bracket (3) as template, locate, mark, and drill four 0.391-in.
diameter holes (5) in right rear wheelhouse (4).
15-2. Install four inserts (6) in right rear wheelhouse (4).
15-3. Install HF 150 watt radio mounting bracket (3) on wheelhouse (4) with four capscrews (1) and
lockwashers (2).
1
3
2
4
~
6
5
1.
2.
3.
6.
CAPSCREW – B1821BH025C100N – QTY. 4
LOCKWASHER – MS45904-71 – QTY. 8
R/T RADIO MOUNTING BRACKET – RF-5073VSM – QTY. 1
INSERT – 12446871-2 – QTY. 4
Figure 5-53.
5-43
TB 9-2320-387-35-4
Section XVI. EPLRS USER READOUT (URO) INSTALLATION
16-1. Remove two existing screws (2) and connector bracket (3) from URO bracket (1).
1
3
2
Figure 5-54.
16-2. Using URO bracket (1) as template, locate, mark and drill four 0.218-in. diameter holes (7)
in right rear wheelhouse (4).
16-3. Install URO bracket (1) on right rear wheelhouse (4) with four capscrews (9), spacers (8), washers (6),
and locknuts (5).
~
9
1.
5.
6.
8.
9.
1
8
7
6
5
USER READOUT BRACKET (URO) – A3006206 – QTY. 1
NUT – MS35650-302 – QTY. 3
LOCKWASHER – MS35338-43 – QTY. 3
SPACER – 92510A318 – QTY. 4
CAPSCREW – MS35207-265 – QTY. 4
Figure 5-55.
5-44
4
TB 9-2320-387-35-4
Section XVII. TAC-SAT RADIO MOUNT INSTALLATION
NOTE
It is necessary to relocate ammo box tray to install TAC-SAT radio
mount. Perform steps 17-1 through 17-7 to relocate ammo box tray.
17-1. Remove four capscrews (1) and (3), lockwashers (10) and (4), and ammo box tray (2) from
cargo floor (7).
17-2. Modify tray (2) to match holes in armor plate (8).
17-3. Using ammo box tray (2) as template, locate, mark and drill two 0.531-in. diameter holes (6) in cargo
floor (7).
17-4. Install two inserts (5) in cargo floor (7).
17-5. Install two inserts (9) in armor plate (8).
17-6. Install ammo box tray (2) on armor plate (8) with two capscrews (1) and lockwashers (10).
17-7. Secure ammo box tray (2) on cargo floor (7) with two capscrews (3) and lockwashers (4).
2
1
3
4
10
5
9
~
6
~
7
1.
3.
4.
5.
9.
10.
CAPSCREW – B1821BH025C075N – QTY. 2
CAPSCREW – B1821BH031C100N – QTY. 2
LOCKWASHER – MS45904-72 – QTY. 2
INSERT – 12446871-1 – QTY. 2
INSERT – 12446871-2 – QTY. 2
LOCKWASHER – MS35338-44 – QTY. 2
Figure 5-56.
5-45
8
TB 9-2320-387-35-4
17-8. Locate, mark, and drill one 0.531 in. diameter hole (15) in armor plate (16).
17-9. Using resilient mount (12) as template, locate, mark and drill three 0.531-in. diameter holes (13) in
cargo floor (14).
17-10. Install four inserts (17) in cargo floor (14).
17-11. Enlarge holes (18) in resilient mount (12) to 0.50 in. diameter.
17-12. Install resilient mount (12) on cargo floor (14) and armor plate (16) with four capscrews (11) and
lockwashers (19).
17-13. Install TAC-SAT mount (22) to resilient mount (12) with four capscrews (20) and lockwashers (21).
20
11
21
12
22
19
~
18
12
17
~
13
15
14
3.00
~
4.75
16
11.
12.
17.
19.
CAPSCREW – B1821BH031C100N – QTY. 4
TAC-SAT RADIO MOUNT – RF-5800H-V005 – QTY. 1
INSERT – 12446871-8 – QTY. 4
LOCKWASHER – MS45904-72 – QTY. 4
22. TAC-SAT RADIO MOUNT P/O –
RF-5800H-V005 – QTY. 1
Figure 5-58.
Figure 5-57.
5-46
TB 9-2320-387-35-4
Section XVIII. TAC-SAT RADIO AND HF RADIO SPEAKER INSTALLATION
NOTE
• Fabricate bracket from 0.125-in. barstock.
• The following procedure applies to TAC-SAT radio loudspeaker
or HF radio loudspeaker.
18-1. Drill one 0.391-in. diameter hole (8) in bracket (3).
18-2. Drill two 0.531-in. diameter holes (6) in bracket (3).
18-3. Install speaker (4) on bracket (3) with existing washer (2) and wingnut (1).
18-4. Install bracket (3) and speaker (4) into turret support beam (7) with bolt (5).
1
2
6
7
8
6
~
2.2
5
1.00
3
1.00
6.00
12.00
5
4
4. SPEAKER – 10181-5180-01 – QTY. 2
5. CAPSCREW – B1821BH031C125N – QTY. 2
Figure 5-59.
5-47
TB 9-2320-387-35-4
Section XIX. COUPLER INSTALLATION
NOTE
Position coupler mounting plate flush against gas spring bracket.
19-1. Locate, mark, and drill eight 0.281-in. diameter holes (6) in side of wheelhouse (3).
19-2. Cut notch (9) in coupler plate (8) for bump (10) on bottom of wheelhouse (3).
19-3. Install coupler plate (8) on wheelhouse (3) with six capscrews (1A), twelve lockwashers (2),
six spacers (5), and six nuts (4).
19-4. Secure coupler plate (8) to wheelhouse (3) with capscrew (1B), five lockwashers (2), ground strap (7),
spacer (5), and nut (4).
19-5. Secure coupler plate (8) to wheelhouse (3) with capscrew (1C), two lockwashers (2), ground strap (7),
spacer (5), and nut (4).
2
1A
3
9
1C
10
2
4
~
~
7
2
8
5
6
1B
7
2
2
1.
2.
4.
5.
7.
8.
CAPSCREW – MS35307-308 – QTY. 8
LOCKWASHER – MS45904-71 – QTY. 20
NUT – MS51971-1 – QTY. 8
SPACER – 10181-5214-01 – QTY. 8
GROUND STRAP – 7147-1167-3 – QTY. 2
COUPLER MOUNTING PLATE – 11080-0511-02 – QTY. 1
Figure 5-60.
5-48
TB 9-2320-387-35-4
NOTE
Remove top plate of coupler mounting bracket to tighten
capscrews.
19-6. Locate, mark, and drill 1.625-in. diameter hole (11) in right rear wheelhouse (3).
19-7. Install resilient mount (14) on coupler plate (8) with six lockwashers (12) and nuts (13).
3
8
~
~
1.00
↔
14
11
~
12
13
12. LOCKWASHERS – MS35338-141 – QTY. 6
13. NUT – MS51971-3 – QTY. 6
14. RESILIENT MOUNT – P/O 11080-0511-02 – QTY. 1
Figure 5-61.
5-49
TB 9-2320-387-35-4
NOTE
Ensure convoluted tubing is cut straight and even to allow proper
fit of locking collar.
19-8. Install locking collar (15) on one end of convoluted tubing (16).
19-9. Place convoluted tubing and grommet assembly (16) in hole (17) of right wheelhouse (3), through
wheelhouse (3), and through hole (11) in right wheelhouse (3). Mark convoluted tubing (16) at
proper length.
19-10. Remove convoluted tubing (16) from wheelhouse (3) and cut to proper length.
NOTE
Ensure convoluted tubing is cut straight and even to allow proper
fit of locking collar.
19-11. Install locking collar (15) on other end of convoluted tubing (16).
19-12. Place convoluted tubing and grommet assembly (16) in hole (11) on inside of right wheelhouse (3),
through wheelhouse (3), and through hole (17) in rear wall (3). Secure convoluted tubing (16) to
rear wall (3) with nylon nuts (18).
16
16
15
17
3
~
15. LOCKING COLLAR – Z52-0013-002 – QTY. 2
16. CONVOLUTED TUBING – Z52-0013-001 – QTY. 1
Figure 5-62.
16
~
18
3
18
11
18. NYLON NUT – 10075-1397 – QTY. 1
18. NYLON NUT – 10075-1397 – QTY. 1
Figure 5-63.
Figure 5-64.
5-50
TB 9-2320-387-35-4
19-13. Route antenna cable (19) through convoluted tubing (16).
16
19
19. HF ANTENNA CABLE – 10564-3355-A004 – QTY. 1
Figure 5-65.
5-51
TB 9-2320-387-35-4
Section XX. VIC-3 MOUNTING INSTALLATION: REAR FFCS/L AND CABLES
20-1. Install rear FFCS/L module (4) on existing bracket (7) with two capscrews (5), four washers (3),
two washers (6), lockwashers (2), and nuts (1).
4
1
2
3
~
5
7
3
6
1.
2.
3.
4.
5.
6.
NUT – 9417954 – QTY. 2
LOCKWASHER – MS35338-45 – QTY. 2
WASHER – 2436162 – QTY. 4
FFCS/L MODULE – A3206624 – QTY. 1
CAPSCREW – B1821BH031C150N – QTY. 2
WASHER – 2436164 – QTY. 2
Figure 5-66.
5-52
TB 9-2320-387-35-4
NOTE
Cables removed for clarity.
20-2. Install cable assembly (10) to front FFCS/L (11).
20-3. Install cable assembly (10) to MCS/L (14).
20-4. Install cable assembly (12) to front FFCS/L (11).
20-5. Install cable assembly (12) to MCS/L (14).
20-6. Install power cable assembly (13) to MCS/L (14).
20-7. Install R/T cable assembly (15) to MCS/L (14). Connect R/T cable assembly (15) to A4J4 connector (9)
on SINCGARS mount (17).
20-8. Install R/T cable assembly (16) to MCS/L (14). Connect R/T cable assembly (16) to A4J3 connector (8)
on SINCGARS mount (17).
8
9
10
17
11
12
12
16
15
14
10
13
10.
12.
13.
15.
16.
CABLE ASSEMBLY – A3206018-2 – QTY. 1
CABLE ASSEMBLY – A3206018-15 – QTY. 2
POWER CABLE ASSEMBLY – A3206017-3 – QTY. 1
CABLE ASSEMBLY, R/T – A3206019-3– QTY. 1
CABLE ASSEMBLY, R/T – A3206127-3 – QTY. 1
Figure 5-67.
5-53
TB 9-2320-387-35-4
20-9. Route two cable assemblies (12) along underside of radio rack (22). Secure cable assemblies (12) to
radio rack (22) with two loop clamps (19), self-tapping screws (20), and tiedown straps (21).
20-10. Route cable assemblies (12) under left side tunnel insulation (18).
20-11. Route cable assemblies (12) along tunnel (23). Secure cable assemblies (12) to tunnel (23) with
three loop clamps (19) and self-tapping screws (20).
20-12. Route cable assemblies (12) behind left rear seat (25) and up rear wall (24) to rear FFCS/L (4).
Secure cable assemblies (12) to rear wall with loop clamp (19) and self-tapping screw (20).
20-13. Connect cable assemblies (12) to rear FFCS/L (4).
22
12
19
20
18
21
~
20
19. LOOP CLAMP – MS21333-69 – QTY. 1
20. SELF-TAPPING SCREW – 9421073 – QTY. 1
21. TIEDOWN STRAP – MS3367-1-0 – QTY. 2
Figure 5-68.
5-54
19
TB 9-2320-387-35-4
12
20
19
20
19
~
20
23
19. LOOP CLAMP – MS21333-69 – QTY. 3
20. SELF-TAPPING SCREW – 9421073 – QTY. 3
19
Figure 5-69.
4
12
24
~
12
19
20
25
19. LOOP CLAMP – MS21333-69 – QTY. 1
20. SELF-TAPPING SCREW – 9421073 – QTY. 1
Figure 5-70.
5-55
TB 9-2320-387-35-4
Section XXI. PLGR BRACKET INSTALLATION
21-1. Locate, mark, and drill two 0.218-in. diameter holes (2) in integrated rack (1).
2
~
1
0.88
1.00
2.25
Figure 5-71.
5-56
TB 9-2320-387-35-4
21-2. Secure mounting bracket (5) to two lower holes in PLGR bracket (6) with two screws (3) and
locknuts (4). Do not tighten locknuts (4).
6
3
5
4
3.
4.
5.
6.
SCREW – MS35206-266 – QTY. 2
LOCKNUT – MS17829-3C – QTY. 2
MOUNTING BRACKET – 12480575 – QTY. 1
PLGR BRACKET – 986-0645-001 – QTY.1
Figure 5-72.
5-57
TB 9-2320-387-35-4
21-3. Install PLGR mount assembly (7) on integrated rack (1) with two screws (3) and locknuts (4), using
upper holes (8) only. Do not tighten locknuts (4).
7
~
1
4
8
3
3. SCREW – MS35206-266 – QTY. 2
4. LOCKNUT – MS17829-3C – QTY. 2
Figure 5-73.
5-58
TB 9-2320-387-35-4
Section XXII. PLGR POWER CABLE INSTALLATION
22-1. Route PLGR power cable (2) from PLGR assembly (1) to B-beam (3).
1
2
~
2
3
2. PLGR POWER CABLE – 9728558-10 – QTY. 1
Figure 5-74.
22-2. Attach shrink tubing (7) and terminal lugs (5) and (11) to PLGR power cable negative lead (10) and
PLGR power cable positive lead (8). (Refer to TM 9-2320-387-24 for terminal connector repair.)
22-3. Attach PLGR power cable positive lead (8) to 24-volt terminal board stud (4) with existing nut (6).
22-4. Attach PLGR power cable negative lead (10) to ground strap stud (12) with existing nut (9).
5
6
7
4
8
11
12
7
10
5. TERMINAL LUG – 7728780 – QTY. 1
7. SHRINK TUBING – MS23053/4-302-0 – QTY. A/R
11. TERMINAL LUG – 7728777 – QTY. 1
Figure 5-75.
5-59
9
TB 9-2320-387-35-4
Section XXIII. PLGR ANTENNA AND CABLE INSTALLATION
23-1. Remove deep water fording intake stack. (Refer to TM 9-2320-387-24.)
23-2. Remove right windshield deflector. (Refer to TM 9-2320-387-24.)
23-3. Locate, mark, and drill two 0.147-in. diameter holes (2) in plenum (1).
23-4. Route PLGR antenna cable (3) along plenum (1) using two loop clamps (4) and self-tapping
screws (5).
1
~
2
3
4
4
5
5
3. PLGR ANTENNA CABLE – 426-0141-050 – QTY. 1
4. LOOP CLAMP – MS21333-67 – QTY. 2
5. SELF-TAPPING SCREW – 9440025 – QTY. 2
Figure 5-76.
23-5. Cut grommet (6) to fit opening (8) and install in right windshield deflector (7).
6
~
7
8
6. GROMMET – 12460299 – QTY. 1
Figure 5-77.
5-60
TB 9-2320-387-35-4
23-6. Locate, mark, and drill 0.562-in. diameter hole (11) in A-frame pillar (10).
NOTE
Wrap a section of PLGR antenna cable with tape to prevent PLGR
antenna cable from being pulled into vehicle.
23-7. Split grommet (9) and insert PLGR antenna cable (3) and grommet (9) in hole (11) in A-frame
pillar (10).
23-8. Apply RTV sealant around grommet (9).
3
9
10
~
1.12
2.37
9. GROMMET – MS35489-31 – QTY. 1
11
Figure 5-78.
23-9. Attach PLGR antenna (14) to support bracket (15) with screw (12) and lockwasher (13).
23-10. Attach support bracket (15) to right windshield armor plate (23) with two existing screws (16),
lockwashers (17), and washers (18).
23-11. Route PLGR antenna cable (3) along right windshield armor plate (23) with loop clamp (22),
existing screw (19), lockwasher (20), and washer (21).
23-12. Connect PLGR antenna cable (3) to PLGR antenna (14).
14
13
3
12
15
16
~
23
12.
13.
14.
15.
22.
SCREW – MS35207-261 – QTY. 1
LOCKWASHER – MS35338-43 – QTY. 1
PLGR ANTENNA – AT575-030 – QTY. 1
SUPPORT BRACKET – 12460300 – QTY. 1
LOOP CLAMP – MS21333-96 – QTY. 1
22
18
21
Figure 5-79.
5-61
20 19
17
TB 9-2320-387-35-4
23-13. Secure PLGR power cable (27) and PLGR antenna cable (3) to PLGR mount assembly (24) with
loop clamp (26), existing locknut (28), and screw (25).
23-14. Install right windshield deflector. (Refer to TM 9-2320-387-24.)
23-15. Install deep water fording stack. (Refer to TM 9-2320-387-24.)
24
3
25
28
26
27
26. LOOP CLAMP – MS21333-78 – QTY. 1
Figure 5-80.
5-62
TB 9-2320-387-35-4
Section XXIV. CABLES INSTALLATION
24-1. Connect SINCGARS antenna cable (1) to antenna (2).
24-2. Route SINCGARS antenna cable (1) down to top of right rear wheelwell (3).
1
2
3
~
1. SINCGARS ANTENNA CABLE – A3014031-17 – QTY. 1
Figure 5-81.
5-63
TB 9-2320-387-35-4
24-3. Remove twelve screws (4), four screws (6), and cargo floor cover (5) from cargo floor (7). Retain all
screws (4) and (6).
5
4
~
~
6
7
Figure 5-82.
24-4. Cut notches in cargo floor cover (5) as shown.
24-5. Cut and install grommet material (8) to fit. Secure with RTV compound.
24-6. Remove three screws (10), washers (13), nuts (12), and rear partition access cover (11) from rear
partition (9).
8
10
4
1.00
3
5
8
11
9
0.8
75
~
1.00
13
8. GROMMET MATERIAL – MS21266-1N – QTY. A/R
Figure 5-83.
5-64
12
TB 9-2320-387-35-4
24-7. Locate, mark, and drill a 0.750-in. hole (14) in right rear wheelhouse (3).
24-8. Insert grommet (15) into hole (14) in right rear wheelhouse (3).
3
~
14
15
15. GROMMET – MS35489-149 – QTY. 1
Figure 5-84.
5-65
TB 9-2320-387-35-4
24-9. Remove three screws (16) and cargo floor cover (5) from cargo floor (7) behind right rear
seat (17).
16
7
~
~
5
~
17
Figure 5-85.
24-10. Lay EPLRS power cable (20) and INC-EPUU cable (21) connectors in vicinity of EPLRS mount (22).
Ensure enough slack in cables to connect to equipment when installed.
9
19
20
~
21
22
18
~
25
18.
20.
21.
23.
24.
25.
24
23
HF POWER CABLE – 10181-9826-020 – QTY. 1
EPLRS POWER CABLE – A3004939 – QTY. 1
INC-EPUU CABLE – A3279383-3 – QTY. 1
HF RADIO SPEAKER CABLE – 10535-0707-A020 – QTY. 1
COUPLER CONTROL CABLE – 10181-9823-020 – QTY. 1
HF ANTENNA CABLE – 10181-9824-020 – QTY. 1
3
Figure 5-86.
24-11. Route HF power cable (18) behind mounts (22) and (19) along wheelhouse (3) to rear partition (9).
24-12. Position HF antenna cable (25), speaker cable (23), and control cable (24) in vicinity of HF 150 watt
radio mount (19).
5-66
TB 9-2320-387-35-4
24-13. Connect EPLRS antenna cable (27) to EPLRS antenna (26).
26
27
27. EPLRS ANTENNA CABLE – SM-C-911480 – QTY. 1
Figure 5-87.
24-14. Drill 1.00-in. hole (28) in wheelhouse (3).
24-15. Route EPLRS antenna cable (27) through grommet (29) in wheelhouse (3).
28
3
29
27
~
29. GROMMET – MS35489-19 – QTY. 1
Figure 5-88.
5-67
TB 9-2320-387-35-4
24-16. Route EPLRS antenna cable (27) through bracket (30) and along frame (31).
27
~
~
31
30
Figure 5-89.
5-68
TB 9-2320-387-35-4
24-17. Secure EPLRS antenna cable (27) to taillight wiring harness (32) with tie-down straps (33).
27
32
33
33. TIE-DOWN STRAP – MS3367-1-0 – QTY. A/R
Figure 5-90.
5-69
TB 9-2320-387-35-4
24-18. Route antenna cable (45) along existing taillight wiring harness (41) and EPLRS antenna cable (40)
and secure with four existing loop clamps (42) and existing self-tapping screws (43).
24-19. Route antenna cable (45) along existing taillight wiring harness on left-side frame rail and secure
with existing loop clamp (39), and existing self-tapping screw (43).
24-20. Route antenna cable (45) along existing taillight wiring harness and secure with existing
loop clamp (44), self-tapping screw (37) and lockwasher (38).
24-21. Route antenna cable (45) along existing taillight wiring harness and secure with existing loop
clamp (48), screw (50), lockwasher (49), washer (47), and nut (46).
24-22. Route antenna cable (45) to antenna base (52) with existing loop clamp (34), screw (51),
lockwasher (35), and nut (36).
24-23. Route SINCGARS antenna cable (45) through hole (54) in rear wall (55).
24-24. Attach SINCGARS antenna cable (45) to antenna base (53).
24-25. Coil excess antenna cable (45) and secure to inside of taillight closeout cover with tiedown
strap (33).
34
52
35
36
37
51
38
39
40
41
42
33
50
49
48
47
46
45
44
43
33. TIEDOWN STRAP – MS3367-1-0 – QTY. A/R
Figure 5-91.
5-70
TB 9-2320-387-35-4
54
53
55
~
45
45. SINCGARS ANTENNA CABLE – A3014031-17 – QTY. 1
Figure 5-92.
24-26. Feed SINCGARS antenna cable (45) and EPLRS antenna cable (27) through hole and grommet (15)
in right-rear wheelwell (3).
15
45
27
~
3
Figure 5-93.
5-71
TB 9-2320-387-35-4
24-27. Route EPLRS power cable (20), INC-EPUU cable (21), HF radio speaker cable (23) and SINCGARS
antenna cables (45) along channel of cargo floor (7) towards front of vehicle.
24-28. Route EPLRS antenna cable (27) up wheelhouse (3) to vicinity of EPLRS mount (22) behind HF 150
watt radio mount (19).
24-29. Secure cables to wheelhouse (3) with loop clamp (56) and self-tapping screw (57).
19
22
3
57
56
45
27
~
23
7
20
21
56. LOOP CLAMP – MS21333-77 – QTY. 1
57. SELF-TAPPING SCREW – 9421073 – QTY. 1
Figure 5-94.
5-72
TB 9-2320-387-35-4
24-30. Drill one 0.147-in. diameter hole (58) in right rear wheelhouse (3) near right gas spring (59).
24-31. Secure EPLRS power cable (20) and INC-EPUU cable (21), EPLRS antenna cable (27), coupler
control cable (24), HF radio speaker cable (23), and HF 150 watt radio antenna cable (25) to right
rear wheelhouse (3) with loop clamp (56) and self-tapping screw (57).
3
27
25 24
20
57
56
~
21
23
59
56. SELF-TAPPING SCREW – 9421073 – QTY. 1
57. LOOP CLAMP – MS21333-77 – QTY. 1
Figure 5-95.
24-32. Drill one 0.147-in. diameter hole (60) in right rear wheelhouse (3).
60
~
3
1.00
6.00
Figure 5-96.
5-73
58
TB 9-2320-387-35-4
24-33. Route TAC-SAT antenna cable (65) through hole (63) in cargo door (64).
24-34. Install grommet (62) on cable (65).
24-35. Connect TAC-SAT antenna cable (65) to TAC-SAT antenna (61).
24-36. Install grommet (62) in hole (63).
61
65
62
63
~
62. GROMMET – MS35489-150 – QTY. 1
65. CABLE – 10369-7211-20 – QTY. 1
Figure 5-97.
5-74
64
TB 9-2320-387-35-4
24-37. Secure antenna cable (65) to underside of cargo door (64) on existing stud (66) with loop clamp (67),
ground strap (69), and nut (68).
24-38. Install ground strap (69) to body of vehicle (73) with existing stud (72), washer (70), and nut (71).
24-39. Secure antenna cable (65) to rear partition (9) with five loop clamps (67) and existing capscrews (74).
24-40. Route antenna cable (65) to right rear wheelhouse.
64
~
66
67
68
65
72
73
70
69
71
Figure 5-98.
65
~
74
67
9
67. LOOP CLAMP – MS21333-112 – QTY. 6
Figure 5-99.
5-75
TB 9-2320-387-35-4
24-41. Route TAC-SAT antenna cable (65) and HF 150 watt power cable (18) down side of wheelhouse (3)
and through cutout in cargo floor cover (5).
24-42. Secure cables (65) and (18) to wheelhouse (3) with two loop clamps (67) and existing screws (75).
65
18
3
75
~
67
5
~
67. LOOP CLAMP – MS21333-112 – QTY. 2
Figure 5-100.
5-76
TB 9-2320-387-35-4
24-43. Route TAC-SAT antenna cable (65) to TAC-SAT radio mount (76).
24-44. Route TAC-SAT power cable (77) from TAC-SAT radio mount (76) to tunnel.
76
77
65
77. TAC-SAT POWER CABLE – 10570-0705-A021 – QTY. 1
Figure 5-101.
5-77
TB 9-2320-387-35-4
24-45. Bundle TAC-SAT antenna cable (65) and HF 150 watt radio power cable (18) with tie-down
straps (33) and position between HF 150 watt radio mount (19) and rear partition (9).
9
33
~
65
18
33. TIE-DOWN STRAP – MS33367-1-0 – QTY. A/R
Figure 5-102.
5-78
19
TB 9-2320-387-35-4
24-46. Bundle all cables (79) and install in side channel (78) of cargo floor cover (5).
NOTE
Ensure all cables fit neatly within cargo floor channel before
installing cargo floor cover.
24-47. Install cargo floor cover (5) on cargo floor (7) with twelve existing screws (4) and four screws (6)
retained in step 24-3.
79
~
5
~
78
~
6
~
7
4
Figure 5-103.
5-79
TB 9-2320-387-35-4
24-48. Route all cables (79) forward from step 24-28 through cargo access hole (81) and in between
tunnel (82) and right rear seat (80).
81
80
79
~
~
~
82
Figure 5-104.
NOTE
• Perform steps 24-49 and 24-50 if supplemental heater is not
installed. Perform 24-51 and 24-52 if supplemental heater is
installed.
• Do not route TAC-SAT or HF radio speaker cables through
tunnel.
24-49. Locate, mark, and drill three 0.147-in. diameter holes (83) in side of tunnel (82), evenly spaced
apart.
24-50. Secure cables (79) to side of tunnel (82) with three clamps (84) and self-tapping screws (85).
24-51. Locate, mark, and drill two 0.147-in. diameter holes (83) in side of tunnel (82), evenly spaced apart.
24-52. Secure all cables (79) to side of tunnel (82) with two loop clamps (84) and self-tapping screws (85),
and clamp (84), existing bracket (87), and screw (86).
83
82
83
~
82
83
~
~
85
84
84
~
79
85
84. LOOP CLAMP – MS21333-75 – QTY. 3
85. SELF-TAPPING SCREW – 9421073 – QTY. 2
Figure 5-105.
5-80
84
84
79
85
85 87
86
TB 9-2320-387-35-4
NOTE
Remove terminal board cover before connecting leads, and
reinstall cover after leads are connected.
24-53. Attach heat shrink tubing (90) and two terminal lugs (88) and (95) to power cable negative lead
(94) and power cable positive lead (91). (Refer to TM 9-2320-387-24 for terminal connector repair.)
24-54. Connect power cable positive lead (91) to 24-volt terminal board (97), located on cab enclosure panel
(98), with existing nut (89).
24-55. Connect power cable negative lead (94) to ground strap (96), located on cab enclosure panel (98),
with existing nut (93). Secure leads (91) and (94) together with tiedown strap (92).
88
89
98
90
92
91
97
~
96
88.
90.
92.
95.
93
95
90
94
TERMINAL LUG – 7728780 – QTY. 1
SHRINK TUBING – MS23053/4-302-0 – QTY. A/R
TIEDOWN STRAP – MS3367-1-0 – QTY. A/R
TERMINAL LUG – 7728777 – QTY. 1
Figure 5-106.
24-56. Route remaining cables to integrated rack (99) using one loop clamp (101), existing
capscrew (104), lockwasher (103), and washer (102).
24-57. Route cables along bar (105) to top of integrated rack (99) with two tiedown straps (100).
99
104
105
103
102
100
101
100. TIEDOWN STRAP – MS53367-1-0 – QTY. 2
101. LOOP CLAMP – MS21333-104 – QTY. 1
Figure 5-107.
5-81
TB 9-2320-387-35-4
24-58. Install fuse (109) inside case (107). Secure with nut (108).
24-59. Install case (107) inside holder (106).
24-60. Install holder (106) on HF 150 watt radio power cable.
106
107
108
109
107
106
Figure 5-108.
5-82
TB 9-2320-387-35-4
24-61. Locate, mark, and drill 1.50-in. diameter hole (111) in front battery box (110).
24-62. Cut grommet (112) to a length of 4.68 in. Install grommet (112) in battery box (110).
24-63. Route HF 150 watt power cable (18) through hole (111) in battery box (110).
111
110
1.125
~
112
3.125
112. GROMMET – MS21266-2N – QTY. 1
Figure 5-109.
110
18
~
111
Figure 5-110.
5-83
TB 9-2320-387-35-4
24-64. Route URO extension cable (113) from EPLRS bracket (22) to URO bracket (117).
24-65. Connect URO extension cable (113) to URO bracket (117) with four screws (114), lockwashers (115), and
nuts (116).
22
117
116
115
114
113
Figure 5-111.
24-66. Connect two speaker cables (120) and (121) to TAC-SAT radio speaker (119).
24-67. Connect two speaker cables (23) and (120) to HF radio speaker (118).
24-68. Route speaker cables (122) down rear partition (9) behind TAC-SAT radio mount (76).
24-69. Bundle speaker cables (122) with tie-down straps (33) as necessary.
119
23
33
118
9
120
122
~
121
76
33. TIE-DOWN STRAP – MS3367-1-0 – QTY. A/R
120. SPEAKER POWER CABLE – 10535-0708-A020 – QTY. 2
121. TAC-SAT SPEAKER R/T CABLE – 10535-0707-A020 – QTY. 1
Figure 5-112.
5-84
By Order of the Secretary of the Army:
PETER J. SCHOOMAKER
General, United States Army
Chief of Staff
Official:
JOYCE E. MORROW
Administrative Assistant to the
Secretary of the Army
0620108
Distribution:
To be distributed in accordance with the Initial Distribution Number (IDN) 344859 requirements for
TB 9-2320-387-35-4.
RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
Use Part II (reverse) for Repair Parts and
Special Tools Lists (RPSTL) and Supply
Catalogs/Supply Manuals (SC/SM).
For use of this form, see AR 25-30;
the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form)
(include ZIP code)
DATE:
3 Nov 2006
FROM: (Activity and location) (include ZIP code)
Co. B, 1st BN, 2nd Brigade
Ft. Hood, TX 76445
AMSTA-LC-LPIT/Tech Pubs, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PA RT I – A L L P U B L I C AT I O N S ( E X C E P T R P S T L A N D S C / S M ) A N D B L A N K F O R M S
PUBLICATION/FORM NUMBER
DATE
TB 9-2320-387-35-4
ITEM
NO.
PAGE
NO.
PARAGRAPH
TITLE
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
1 OCT 2006
LINE
NO.*
5-45
FIGURE
NO.
5-55
TABLE
NO.
RECOMMENDED CHANGES AND REASON
( Provide exact wording of recommended changes, if possible)
We are using spacer 92510A318 (Qty. 4) with URO
bracket.
SAMPLE
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE, OR TITLE
Pat Smith
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON,
PLUS EXTENSION
AV272-4162
SIGNATURE
Pat Smith
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (include ZIP code)
DATE:
AMSTA-LC-LPIT/Tech Pubs, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PA RT I I – R E PA I R PA RT S A N D S P E C I A L T O O L S L I S T S A N D S U P P LY C ATA L O G S / S U P P LY M A N U A L S
PUBLICATION/FORM NUMBER
DATE
TB 9-2320-387-35-4
PAGE COLM LINE
NO. NO. NO.
NATIONAL
STOCK
NUMBER
TITLE
1 OCT 2006
TOTAL NO.
REFERENCE FIGURE ITEM OF MAJOR
NO.
NO.
NO.
ITEMS
SUPPORTED
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
RECOMMENDED ACTION
SAMPLE
PA RT I I I – R E M A R K S
(Any general remarks or recommendations, or suggestions for improvement of publications and blank forms.
Additional blank sheets may be used if more space is needed.)
TYPED NAME, GRADE, OR TITLE
TELEPHONE EXCHANGE/AUTOVON,
PLUS EXTENSION
SIGNATURE
USAPPC V3.00
RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
Use Part II (reverse) for Repair Parts and
Special Tools Lists (RPSTL) and Supply
Catalogs/Supply Manuals (SC/SM).
For use of this form, see AR 25-30;
the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form)
(include ZIP code)
DATE:
FROM: (Activity and location) (include ZIP code)
AMSTA-LC-LPIT/Tech Pubs, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PA RT I – A L L P U B L I C AT I O N S ( E X C E P T R P S T L A N D S C / S M ) A N D B L A N K F O R M S
PUBLICATION/FORM NUMBER
DATE
TB 9-2320-387-35-4
ITEM
NO.
PAGE
NO.
PARAGRAPH
TITLE
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
1 OCT 2006
LINE
NO.*
FIGURE
NO.
TABLE
NO.
RECOMMENDED CHANGES AND REASON
( Provide exact wording of recommended changes, if possible)
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE, OR TITLE
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON,
PLUS EXTENSION
SIGNATURE
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (include ZIP code)
DATE:
AMSTA-LC-LPIT/Tech Pubs, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PA RT I I – R E PA I R PA RT S A N D S P E C I A L T O O L S L I S T S A N D S U P P LY C ATA L O G S / S U P P LY M A N U A L S
PUBLICATION/FORM NUMBER
TB 9-2320-387-35-4
PAGE COLM LINE
NO. NO. NO.
PA RT I I I – R E M A R K S
NATIONAL
STOCK
NUMBER
DATE
TITLE
1 OCT 2006
TOTAL NO.
REFERENCE FIGURE ITEM OF MAJOR
NO.
NO.
NO.
ITEMS
SUPPORTED
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
RECOMMENDED ACTION
(Any general remarks or recommendations, or suggestions for improvement of publications and blank forms.
Additional blank sheets may be used if more space is needed.)
TYPED NAME, GRADE, OR TITLE
TELEPHONE EXCHANGE/AUTOVON,
PLUS EXTENSION
SIGNATURE
USAPPC V3.00
RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
Use Part II (reverse) for Repair Parts and
Special Tools Lists (RPSTL) and Supply
Catalogs/Supply Manuals (SC/SM).
For use of this form, see AR 25-30;
the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form)
(include ZIP code)
DATE:
FROM: (Activity and location) (include ZIP code)
AMSTA-LC-LPIT/Tech Pubs, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PA RT I – A L L P U B L I C AT I O N S ( E X C E P T R P S T L A N D S C / S M ) A N D B L A N K F O R M S
PUBLICATION/FORM NUMBER
DATE
TB 9-2320-387-35-4
ITEM
NO.
PAGE
NO.
PARAGRAPH
TITLE
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
1 OCT 2006
LINE
NO.*
FIGURE
NO.
TABLE
NO.
RECOMMENDED CHANGES AND REASON
( Provide exact wording of recommended changes, if possible)
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE, OR TITLE
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON,
PLUS EXTENSION
SIGNATURE
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (include ZIP code)
DATE:
AMSTA-LC-LPIT/Tech Pubs, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PA RT I I – R E PA I R PA RT S A N D S P E C I A L T O O L S L I S T S A N D S U P P LY C ATA L O G S / S U P P LY M A N U A L S
PUBLICATION/FORM NUMBER
TB 9-2320-387-35-4
PAGE COLM LINE
NO. NO. NO.
PA RT I I I – R E M A R K S
NATIONAL
STOCK
NUMBER
DATE
TITLE
1 OCT 2006
TOTAL NO.
REFERENCE FIGURE ITEM OF MAJOR
NO.
NO.
NO.
ITEMS
SUPPORTED
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
RECOMMENDED ACTION
(Any general remarks or recommendations, or suggestions for improvement of publications and blank forms.
Additional blank sheets may be used if more space is needed.)
TYPED NAME, GRADE, OR TITLE
TELEPHONE EXCHANGE/AUTOVON,
PLUS EXTENSION
SIGNATURE
USAPPC V3.00
RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
Use Part II (reverse) for Repair Parts and
Special Tools Lists (RPSTL) and Supply
Catalogs/Supply Manuals (SC/SM).
For use of this form, see AR 25-30;
the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form)
(include ZIP code)
DATE:
FROM: (Activity and location) (include ZIP code)
AMSTA-LC-LPIT/Tech Pubs, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PA RT I – A L L P U B L I C AT I O N S ( E X C E P T R P S T L A N D S C / S M ) A N D B L A N K F O R M S
PUBLICATION/FORM NUMBER
DATE
TB 9-2320-387-35-4
ITEM
NO.
PAGE
NO.
PARAGRAPH
TITLE
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
1 OCT 2006
LINE
NO.*
FIGURE
NO.
TABLE
NO.
RECOMMENDED CHANGES AND REASON
( Provide exact wording of recommended changes, if possible)
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE, OR TITLE
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON,
PLUS EXTENSION
SIGNATURE
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (include ZIP code)
DATE:
AMSTA-LC-LPIT/Tech Pubs, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PA RT I I – R E PA I R PA RT S A N D S P E C I A L T O O L S L I S T S A N D S U P P LY C ATA L O G S / S U P P LY M A N U A L S
PUBLICATION/FORM NUMBER
TB 9-2320-387-35-4
PAGE COLM LINE
NO. NO. NO.
PA RT I I I – R E M A R K S
NATIONAL
STOCK
NUMBER
DATE
TITLE
1 OCT 2006
TOTAL NO.
REFERENCE FIGURE ITEM OF MAJOR
NO.
NO.
NO.
ITEMS
SUPPORTED
TECHNICAL BULLETIN
INSTALLATION INSTRUCTIONS
RECOMMENDED ACTION
(Any general remarks or recommendations, or suggestions for improvement of publications and blank forms.
Additional blank sheets may be used if more space is needed.)
TYPED NAME, GRADE, OR TITLE
TELEPHONE EXCHANGE/AUTOVON,
PLUS EXTENSION
SIGNATURE
USAPPC V3.00