OPERATOR'S MANUAL
MODEL #100310
3000 PSI PRESSURE WASHER
or visit championpowerequipment.com
READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product.
Failure to do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
Made in China - REV 20170428
Champion Power Equipment, Inc., Santa Fe Springs, CA USA
100310 - 3000 PSI PRESSURE WASHER
TABLE OF CONTENTS
Table of Contents ........................................ 2
TABLE OF CONTENTS
Storage .................................................. .... 18
Pressure Washer Storage ................................. ..... 18
Engine Stored for Less than 30 Days .................... ..... 19
Introduction ................................................ 3
Engine Stored for Over 30 Days ............................... 19
Safety Definitions ....................................... 3
Winter Storage ................................................. 19
Safety Symbols........................................... 4
Specifications ........................................... 20
Pressure Washer Specifications .......................... ..... 20
Important Safety Instructions .................... 5
Engine Specifications .......................................... 20
Controls and Features ................................ 8
Oil Specifications ............................................... 20
Parts Included ................................................... 9
Fuel Specifications ............................................. 20
Assembly .................................................... 9
Spark Plug Specifications ...................................... 20
Remove the Pressure Washer from the Shipping Carton ...... 9
Install Handle to Bottom Frame................................. 9
Add Engine Oil .................................................. 10
Add Fuel ........................................................ 11
Attach the Trigger Gun Assembly.............................. 11
Connect the High Pressure Hose .............................. 12
Connect the Garden Hose ...................................... 12
Valve Specifications ....................................... ..... 20
Important Message About Temperature....................... 20
Parts Diagram ............................................. ..... 21
Parts List ....................................................... 22
Engine Parts Diagram .......................................... 23
Engine Parts List .......................................... ..... 24
Troubleshooting ................................................ 26
Operation ................................................... 13
Pressure Washer Location ..................................... 13
Before Starting the Engine ..................................... 13
Starting the Engine ............................................. 13
Distance from Cleaning Surface ............................... 13
High Pressure Wash............................................ 14
Low Pressure Wash ............................................ 14
System Flush ................................................... 15
Depressurize System .......................................... 15
Operating Tips .................................................. 15
Stopping the Engine ............................................ 16
Operation at High Altitude ..................................... 16
Maintenance .............................................. 16
Cleaning the Pressure Washer ................................. 17
Changing the Engine Oil ....................................... 17
Cleaning and Adjusting the Spark Plug(s) ..................... 17
Cleaning the Air Filter .......................................... 17
Cleaning the Spark Arrester ................................... 18
Adjusting the Governor ......................................... 18
Maintenance Schedule ......................................... 18
2
INTRODUCTION
100310 - 3000 PSI PRESSURE WASHER
INTRODUCTION
SAFETY DEFINITIONS
Congratulations on your purchase of a Champion Power
Equipment (CPE) product. CPE designs, builds, and supports
all of our products to strict specifications and guidelines. With
proper product knowledge, safe use, and regular maintenance,
this product should bring years of satisfying service.
The purpose of safety symbols is to attract your attention to
possible dangers. The safety symbols, and their explanations,
deserve your careful attention and understanding. The safety
warnings do not by themselves eliminate any danger. The
instructions or warnings they give are not substitutes for proper
accident prevention measures.
Every effort has been made to ensure the accuracy and
completeness of the information in this manual, and we reserve
the right to change, alter and/or improve the product and this
document at any time without prior notice.
Since CPE highly values how our products are designed,
manufactured, operated and are serviced, and also highly
value your safety and the safety of others, we would like you to
take the time to review this product manual and other product
materials thoroughly and be fully aware and knowledgeable
of the assembly, operation, dangers and maintenance of the
product before use. Fully familiarize yourself, and make sure
others who plan on operating the product fully familiarize
themselves too, with the proper safety and operation
procedures before each use. Please always exercise common
sense and always err on the side of caution when operating
the product to ensure no accidents, property damage, or injury
occurs. We want you to continue to use and be satisfied with
your CPE product for years to come.
When contacting CPE about parts and/or service, you will
need to supply the complete model and serial numbers of your
product. Transcribe the information found on your product’s
nameplate label to the table below.
! DANGER
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
! WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
! CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
" NOTICE
NOTICE is used to address practices not related to physical
injury.
CHAMPION POWER EQUIPMENT SUPPORT
1-877-338-0999
MODEL NUMBER
100310
SERIAL NUMBER
DATE OF PURCHASE
PURCHASE LOCATION
3
SAFETY SYMBOLS
100310 - 3000 PSI PRESSURE WASHER
SAFETY SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of
these symbols will allow you to more safely operate the product.
SYMBOL
MEANING
Read the Operator’s Manual. To reduce the risk of injury, user must read and understand operator’s
manual before using this product.
Electric Shock. Failure to use in dry conditions and to observe safe practices can result in electric shock.
Toxic Fumes. The engine exhaust from this product contains chemicals known to the state of California to
cause cancer and birth defects and other reproductive harm.
Risk of Asphyxiation. This engine emits carbon monoxide, an oderless, colorless poison gas. Breathing
carbon monoxide can cause nausea, fainting or death. Use only in a well ventilated area.
Risk of Injections. To reduce the risk of injection or injury, never direct a water stream towards people or
pets or place any body part in the stream. Leaking hoses and fittings are also capable of causing injection
injury. Do not hold hoses or fittings.
Eye and Ear Protection. Always wear safety goggles or safety glasses with side shields, and as necessary
a full faceshield as well as full ear protection when operating this product.
Kickback. To reduce the risk of injury from kickback, hold the trigger gun securely with both hands when
the machine is on.
Risk of Fire. Fuel and its vapors are extremely flammable and explosive. Fire can cause severe burns or
death. Do not add fuel while the product is operating or still hot. Do not spray flammable liquids. Operate
only where open flame is permitted.
Risk of Explosion. Do not spray flammable liquids. Flammable liquids, fuel, and their vapors are explosive
and can cause severe burns or death.
4
100310 - 3000 PSI PRESSURE WASHER
IMPORTANT SAFETY INSTRUCTIONS
! WARNING
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer and birth
defects and other reproductive harm.
IMPORTANT SAFETY INSTRUCTIONS
! WARNING
Sparks can result in fire or electrical shock.
When servicing the pressure washer:
Disconnect the spark plug wire and place it where it cannot
contact the plug.
DO NOT check for spark with the plug removed.
! WARNING
This product contains chemicals known to the State of
California to cause cancer and birth defects and other
reproductive harm.
! DANGER
Engine exhaust contains carbon monoxide, a colorless,
odorless, poison gas. Breathing carbon monoxide will cause
nausea, dizziness, fainting or death. If you start to feel dizzy
or weak, get to fresh air immediately.
Operate this product outdoors only in a well ventilated area.
DO NOT operate the product inside any building, including
garages, basements, crawlspaces and sheds, enclosure or
compartment, including a compartment of a recreational
vehicle.
Use only approved spark plug testers.
! WARNING
Running engines produce heat. Severe burns can occur on
contact. Combustible material can catch fire on contact.
DO NOT touch hot surfaces.
Avoid contact with hot exhaust gases.
Allow equipment to cool before touching.
Maintain at least 91.4 cm (3 ft.) of clearance on all sides to
ensure adequate cooling.
Maintain at least 1.5 m (5 ft.) of clearance from combustible
materials.
" NOTICE
DO NOT allow exhaust fumes to enter a confined area
through windows, doors, vents or other openings.
DO NOT let water in the pump freeze.
DANGER: CARBON MONOXIDE – using this product indoors
CAN KILL YOU IN MINUTES.
See Storage section in the manual for instructions regarding
winter storage.
! DANGER
Rotating parts can entangle hands, feet, hair, clothing and/
or accessories.
If water has frozen in the pressure washer, thaw the
pressure washer in a warm room before starting.
DO NOT pour hot water on or into the pump; internal parts
will be damaged and your warranty will be voided.
Traumatic amputation or severe laceration can result.
Keep hands and feet away from rotating parts.
Tie up long hair and remove jewelry.
Operate equipment with guards in place.
DO NOT wear loose-fitting clothing, dangling drawstrings or
items that could become caught.
" NOTICE
NEVER run the unit dry.
Be sure the water supply is completely turned on before
operating the unit.
! WARNING
Contact with electrical power source can cause electric
shock or burn.
NEVER spray in the direction of or near a power source/
electrical outlet.
5
100310 - 3000 PSI PRESSURE WASHER
IMPORTANT SAFETY INSTRUCTIONS
! WARNING
" NOTICE
NEVER spray flammable liquids or use pressure washer in
areas containing combustible dust, liquids, or vapor.
Improper treatment or use of the pressure washer can
damage it, shorten its life and void your warranty.
NEVER operate this machine in a closed building or in or
near an explosive environment.
Use the pressure washer only for intended uses.
Operate only on level surfaces.
– DO NOT remove fuel tank cap or fill fuel tank while
engine is hot or running (allow engine to cool two
minutes before refueling). Always fill the tank slowly.
DO NOT expose pressure washer to excessive moisture,
dust, or dirt.
– NEVER disconnect the high pressure discharge hose
from the machine while the system is pressurized.
DO NOT use the pressure washer if:
DO NOT allow any material to block the cooling slots.
– Equipment sparks, smokes or emits flames
! WARNING
– Equipment vibrates excessively
Rapid retraction of the starter cord will pull hand and arm
towards the engine faster than you can let go.
! DANGER
Unintentional startup can result in entanglement, traumatic
amputation or laceration.
Risk of injection or injury. High pressure jets can be
dangerous if subject to misuse.
Broken bones, fractures, bruises or sprains could result.
– DO NOT direct discharge stream at persons, animals,
electrical devices, or the machine itself.
When starting engine, pull the starter cord slowly until
resistance is felt and then pull rapidly to avoid kickback.
! DANGER
– ALWAYS point spray gun in safe direction. Everytime you
stop the engine, squeeze trigger of spray gun to relieve
any trapped pressure.
Keep clear of nozzle.
DO NOT point the spray wand at a person, an animal or
yourself.
Always wear safety glasses or goggles and protective
equipment (hearing protection, gloves, rubber boots,
protective clothing) when operating or performing
maintenance.
– NEVER put hand or fingers over the spray tip while
operating the unit.
– NEVER try to stop or deflect leaks with any body part.
– ALWAYS engage the trigger safety latch in the safe
position when spraying is stopped even if only for a few
moments.
" NOTICE
ONLY use cold water.
" NOTICE
Water under high pressure can damage fragile surfaces.
– ALWAYS: practice on a inconspicuous test area to
understand when damage may occur.
– DO NOT: Point spray gun at glass.
– NEVER: Point the spray nozzle at persons, animals,
electrical devices, plants or the machine itself.
! WARNING
Always wear eye protection with side shields marked to
comply with ANSI Z87.1.
Following this rule will reduce the risk of serious personal
injury.
6
100310 - 3000 PSI PRESSURE WASHER
! WARNING
IMPORTANT SAFETY INSTRUCTIONS
! DANGER
Use of pressure washers can create wet walking surfaces.
While using a pressure washer, forces from the gun can
cause you to loose footing and fall.
Fuel and fuel vapors are highly flammable and extremely
explosive.
– Use only on a level surface.
Unintentional startup can result in entanglement, traumatic
amputation or laceration.
– Make sure there is proper drainage to dissipate water.
– DO NOT: use on elevated surface where kickback could
result in a serious fall.
– ALWAYS grasp the gun with two hands to prevent
potential injury do to high pressure from gun.
! WARNING
High pressure spray can splash back at operator or propel
objects.
NEVER: allow children to operate any pressure washer or
play nearby.
NEVER: leave spray gun unattended while machine is
running or until after engine has been turned off and
pressure has been relieved from the spray gun.
NEVER: repair high pressure hose, replace it.
NEVER: repair leaking connections with sealant, replace
damaged O-rings.
NEVER: use spray gun with a damaged or altered trigger
lock.
NEVER: secure the trigger in the open / spray position.
ALWAYS: keep high pressure hose connected to spray gun
and pump while in use.
ALWAYS: be certain that spray gun nozzles and accessories
are properly attached to the lance.
ALWAYS: wear safety goggles when operating this
equipment. NOTE: Safety goggles cover the sides, top
and bottom of the eyes. Don't confuse safety glasses for
goggles.
Fire or explosion can cause severe burns or death.
When adding or removing fuel:
Turn the pressure washer off and let it cool for at least two
minutes before removing the fuel cap.
Loosen the cap slowly to relieve pressure in the tank.
Only fill or drain fuel outdoors in a well-ventilated area.
DO NOT pump gas directly into the pressure washer at the
gas station. Use an approved container to transfer the fuel
to the pressure washer.
DO NOT overfill the fuel tank.
Always keep fuel away from sparks, open flames, pilot
lights, heat and other sources of ignition.
DO NOT light or smoke cigarettes.
When starting the pressure washer:
DO NOT attempt to start a damaged pressure washer.
Make certain that the gas cap, air filter, spark plug, fuel
lines and exhaust system are properly in place.
Allow spilled fuel to evaporate fully before attempting to
start the engine.
Make certain that the pressure washer is resting firmly on
level ground.
When operating the pressure washer:
DO NOT move or tip the pressure washer during operation.
DO NOT tip the pressure washer or allow fuel or oil to spill.
When transporting or servicing the pressure washer:
Make certain that the fuel shutoff valve is in the off position
and the fuel tank is empty.
Disconnect the spark plug wire.
When storing the pressure washer:
Store away from sparks, open flames, pilot lights, heat and
other sources of ignition.
7
CONTROLS AND FEATURES
100310 - 3000 PSI PRESSURE WASHER
CONTROLS AND FEATURES
Read this operator’s manual before operating your pressure washer. Familiarize yourself with the location and function of the controls
and features. Save this manual for future reference.
13
14
1
12
2
11
3
4
9
5
6
10
18
15
8
16
7
17
1. Nozzles
11. Fuel Tank – 3.4 L (0.9 gal.)
2. High Pressure Hose
12. Trigger Gun Assembly – Gun and spray wand
3. Muffler
13. Trigger Gun Holder – Used to hold gun when assembled
and not in use
4. Air Filter – Protects the engine by filtering dust and debris
from the intake air.
5. Throttle Lever – Used to control the engine speed.
14. High Pressure Hose Hanger – Used to hold high pressure
hose when not in use.
6. Choke Lever – Used to start the engine when cold.
15. High Pressure Hose Outlet
7. 30.5 cm (12 in.) Never Flat Tires
16. Garden Hose Inlet
8. Recoil Starter – Used to manually start the engine
17. Detergent Tanks – 1.7 L (0.5 gal.)
9. Engine Switch
18. Detergent Hose Connection Barb
10. Fuel Valve Knob – Used to turn fuel supply on and off to
engine
8
ASSEMBLY
100310 - 3000 PSI PRESSURE WASHER
Parts Included
ASSEMBLY
Gun Assembly
Your pressure washer requires some assembly. This unit ships
from our factory without oil. It must be properly serviced
with fuel and oil before operation. If you have any questions
regarding the assembly of your pressure washer, call our help
line at 1-877-338-0999. Please have your serial number and
model number available.
Spray Wand (A)...................................................................... 1
Trigger Gun (B) ...................................................................... 1
Quick Connect Nozzles (C) ..................................................... 4
Hoses
7.6 m (25 ft.) High Pressure Hose (D) ..................................... 1
0.9 m (35.4 in.) Detergent Hose (E) ........................................ 1
Other
Oil Funnel (F) ......................................................................... 1
A
Remove the Pressure Washer from the
Shipping Carton
1. Set the shipping carton on a solid, flat surface.
2. Remove everything from the carton except the pressure
washer.
3. Carefully cut each corner of the box from top to bottom.
B
Install Handle to Bottom Frame
1. Line up the handle with the bottom frame.
2. Make sure the handle holes are lined up with the bottom
frame spring button (A). Front face of shroud (decal side)
should face the engine
C
D
3. Slide the handle downward on the bottom frame, until
the spring buttons have popped through the holes on the
handle frame. A “click” may sound. (B)
4. Gently pull up on the handle to make sure that two frames
have made a solid connection and that the handle can not
be pulled off without pressing on the spring buttons to
release it.
E
F
A
B
9
ASSEMBLY
100310 - 3000 PSI PRESSURE WASHER
Add Engine Oil
Degrees Celsiusº (Outside)
! CAUTION
DO NOT attempt to crank or start the engine before it has
been properly filled with the recommended type and amount
of oil. Damage to the pressure washer as a result of failure
to follow these instructions will void your warranty.
Full Synthetic 5W-30
" NOTICE
The recommended oil type is 10W-30 automotive oil.
1. Place the pressure washer on a flat level surface.
Degrees Fahrenheitº (Outside)
" NOTICE
We consider the first 5 hours of run time to be the breakin period for the engine. During the break in period we
recommend using standard automotive non-synthetic
blended oils. After the break in period synthetic lubricant
can be used but is not required. Adjusting throttle setting
will increase/decrease engine speed helping to seat piston
rings. Avoid bogging or lugging the engine down and avoid
prolonged running at constant RPM. After the 5 hour breakin period, change the oil. Using synthetic lubricants does not
increase the recommended oil change interval.
2. Remove oil fill cap/dipstick to add oil.
3. Add up to 0.6 L (0.6 qt.) of oil (not included) and replace oil
fill cap/dipstick. DO NOT OVERFILL.
4. Check engine oil level daily and add as needed.
" NOTICE
Once oil has been added, a visual check should show oil
about 1-2 threads from running out of the fill hole.
If using the dipstick to check oil level, DO NOT screw in the
dipstick while checking.
! CAUTION
The engine is equipped with a low oil shut-off and will stop
when the oil level in the crankcase falls below the threshold
level.
" NOTICE
Check oil often during the break-in period. Refer to the
Maintenance section for recommended service intervals.
" NOTICE
The engine rotor has a sealed, pre-lubricated ball bearing
that requires no additional lubrication for the life of the
bearing.
" NOTICE
Weather will affect engine oil and engine performance.
Change the type of engine oil used based on weather
conditions to suit the engine needs.
10
ASSEMBLY
100310 - 3000 PSI PRESSURE WASHER
Add Fuel
" NOTICE
1. Use clean, fresh, regular unleaded fuel with a minimum
octane rating of 85 and an ethanol content of less than
10% by volume.
2. DO NOT mix oil with fuel.
3. Clean the area around the fuel cap.
4. Remove the fuel cap.
5. Slowly add fuel to the tank. DO NOT OVERFILL. Fuel can
expand after filling. A minimum of 6.4 mm (¼ in.) of space
left in the tank is required for fuel expansion, more than
6.4 mm (¼ in.) is recommended. Fuel can be forced out of
the tank as a result of expansion if it is overfilled, and can
affect the stable running condition of the product. When
filling the tank, it is recommended to leave enough space
for the fuel to expand.
Our engines work well with 10% or less ethanol blend fuels.
When using blended fuels there are some issues worth
noting:
– Ethanol-gasoline blends can absorb more water than
gasoline alone.
– These blends can eventually separate, leaving water or a
watery goo in the tank, fuel valve and carburetor.
– With gravity-fed fuel supplies, this compromised fuel
can be drawn into the carburetor and cause damage to
the engine and/or potential hazards.
– There are only a few suppliers of fuel stabilizer that are
formulated to work with ethanol blend fuels.
– Any damages or hazards caused by using improper fuel,
improperly stored fuel, and/or improperly formulated
stabilizers, are not covered by manufacturer's warranty.
It is advisable to always shut off the fuel supply, run the
engine to fuel starvation and drain the tank when the
equipment is not in use for more than 30 days.
Attach the Trigger Gun Assembly
1. Attach the spray wand (A) to the trigger gun (B).
6. Screw on the fuel cap and wipe away any spilled fuel.
2. Rotate (clockwise) the M22 coupler on the trigger gun until
the spray wand is secure. Tighten connection. DO NOT
OVER-TIGHTEN.
! WARNING
Pouring fuel too fast through the fuel screen may result in
blow back of fuel at the operator while filling.
A
B
! CAUTION
Use regular unleaded gasoline with a minimum octane
rating of 85.
Do not mix oil and gasoline.
Fill tank to approximately 6.4 mm (¼ in.) below the top of
the tank to allow for fuel expansion.
DO NOT pump gas directly into the pressure washer at the
gas station. Use an approved container to transfer the fuel
to the pressure washer.
3. Connect the end of the high pressure hose (C) to the
gun inlet. Tighten connection clockwise. DO NOT OVERTIGHTEN.
" NOTICE
Be careful to avoid cross-threading, which can cause the
trigger gun to leak during use.
DO NOT fill fuel tank indoors.
DO NOT fill fuel tank when the engine is running or hot.
C
DO NOT overfill the fuel tank.
DO NOT light cigarettes or smoke when filling the fuel tank.
11
ASSEMBLY
100310 - 3000 PSI PRESSURE WASHER
Connect the High Pressure Hose
1. Completely uncoil and straighten the high pressure hose to
prevent kinks.
2. With the hose faucet turned completely off, attach the end
of the garden hose to the water inlet. Tighten by hand.
2. Align the collar on the hose to the threaded outlet on the
pump.
3. Insert the high pressure hose collar onto the threaded
outlet.
4. Turn the collar clockwise to tighten the hose securely to
the pump.
" NOTICE
Be careful to avoid cross-threading, which can cause the
hose to leak during use.
5. Gently pull on the hose to be certain it is properly secured.
" NOTICE
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely unwind
the hose from its reel or coil and make sure the hose is not
being restricted by tires, rocks, or any other objects that
may lessen or prevent water flow to the pressure washer.
Connect the Garden Hose
The water supply must come from a pressurized water spicket.
NEVER use hot water or water from pools, lakes, etc. Before
connecting the garden hose to the pressure washer:
1. Run water through the hose for 30 seconds to clean any
debris from the hose.
2. Inspect the screen and gasket in the water intake.
3. If the screen and gasket is damaged, do not use the
machine until the screen has been replaced.
4. If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
1. Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
" NOTICE
There must be a minimum of 3 m (10 ft.) of unrestricted
hose between the pressure washer intake and the hose
faucet or shut off valve (such as a “Y” shut off connector).
12
OPERATION
100310 - 3000 PSI PRESSURE WASHER
OPERATION
" NOTICE
Pressure Washer Location
This pressure washer must have at least 1.5 m (5 ft.) of
clearance from combustible material. Leave at least 91.4 cm
(3 ft.) of clearance on all sides of the pressure washer to allow
for adequate cooling, maintenance and servicing. Place the
pressure washer in a well ventilated area. DO NOT place the
pressure washer near vents or intakes where exhaust fumes
could be drawn into occupied or confined spaces. Carefully
consider wind and air currents when positioning pressure
washer.
Before Starting the Engine
Keep choke lever in “CHOKE” position for 2 pulls of the
recoil starter. After second pull, move choke lever to the
“RUN” position for up to the next 3 pulls of the recoil starter.
To much choke leads to spark plug fouling/engine flooding
due to the lack of incoming air. This will cause the engine
not to start.
" NOTICE
If the engine does not start after 2 pulls, relieve pump
pressure by pulling the trigger on the trigger gun.
" NOTICE
1. Turn the water supply ON.
2. Pull the trigger on the trigger gun to purge all air from the
pump and hose. This may take several minutes.
3. Do not start the engine until a steady stream of water is
flowing from the nozzle.
! CAUTION
If the engine starts but does not run make certain that
the pressure washer is on a flat, level surface. The engine
is equipped with a low oil sensor that will prevent the
engine from running when the oil level falls below a critical
threshold.
Distance from Cleaning Surface
Never operate your pressure washer without water.
Starting the Engine
1. Make certain the pressure washer is on a flat, level
surface.
2. Turn engine switch to “ON” position (A).
The distance between the spray nozzle and the cleaning surface
is another factor that affects the impact force of the water.
The impact force of the water increases as the nozzle is
moved closer to the surface. You can vary the impact force by
controlling
– The nozzle’s fan pattern.
– The nozzle’s angle to the cleaning surface.
3. Rotate the fuel valve to the “ON” position (B).
4. Move the throttle lever (C) to the “FAST” position.
5. Move the choke lever (D) to the “CHOKE” position.
6. Pull the starter cord slowly until resistance is felt and then
pull rapidly. SEE NOTE.
7. As engine warms up, move the choke lever (D) to “RUN”
and adjust the throttle (C) as needed.
– The nozzle’s distance from the cleaning surface.
Never use a narrow high impact stream on a surface that is
susceptible to damage. Avoid spraying windows with a narrow
high impact stream or turbo nozzle. Doing so may break the
glass.
1. Before triggering the gun, select a nozzle with a wide fan
pattern.
2. Place the nozzle approximately 1.2 m - 1.5 m (4-5 ft.) away
from the cleaning surface. Then hold the nozzle at a 45
degree angle to the cleaning surface. Trigger the gun.
B
C
A
3. Vary the fan pattern spray angle and the distance to the
cleaning surface until optimum cleaning efficiency is
achieved without damaging the surface.
D
13
OPERATION
100310 - 3000 PSI PRESSURE WASHER
Use the following table to determine which nozzle to use.
NOZZLE SELECTION GUIDE
0°
25°
40°
Soap
0°
Abrasive
LOW PRESSURE
WASH
HIGH PRESSURE WASH
25°
40°
Soap
Gentle
Concrete, Brick, Masonry
Siding, Gutters, Home
Fencing, Deck, Patio
Lawn and Garden Equipment,
Boats, RVs
Recommended nozzle
Use with caution
High Pressure Wash
! CAUTION
Always engage the trigger safety latch when the unit is not
in use.
The trigger safety latch prevents the gun from being
triggered accidentally. Push the latch fully down to engage
it.
! WARNING
Injection hazard.
Fully unwrap and straighten high pressure hose prior to
and during each use and do not allow it to become kinked.
The high pressure hose features an outer covering that
provides strength to the hose. If the outer covering becomes
damaged, stop using the hose and replace it immediately. A
kinked or damaged hose can develop a high pressure leak
and result in a possible injection or other serious personal
injury.
" NOTICE
If the starter grip and rope becomes difficult to pull, squeeze
the trigger to relieve water pressure before attempting to
start the engine again.
For high pressure cleaning, refer to the Nozzle Selection Guide
for more information about which quick connect nozzle to
choose.
! CAUTION
The narrow high impact spray can damage some surfaces.
A wide fan pattern distributes the impact of the water over a
larger area resulting in excellent cleaning action with reduced
risk of surface damage. Clean large surface areas quickly using
a wide fan pattern.
Low Pressure Wash
Detergent Use
The use of detergents can dramatically reduce cleaning time
and assist in the removal of difficult stains. Many detergents
14
OPERATION
100310 - 3000 PSI PRESSURE WASHER
are customized for pressure washer use on specific cleaning
tasks. Pressure washer detergents are as thick as water.
Using thicker detergents – like dish soap – will clog the
chemical injection system.
System Flush
After using detergents, flush the suction system by placing the
detergent suction tube into a bucket of clean water.
! WARNING
" NOTICE
Use only detergents designed for pressure washers.
Do not use household detergents, acids, alkalines, bleaches,
solvents, flammable material, or industrial grade solutions,
which can damage the pump or cause property damage.
Many detergents may require mixing prior to use. Prepare
cleaning solution as instructed on the solution bottle.
Always test in an inconspicuous area before beginning.
You can effectively clean surfaces by combining the chemical
action of detergents with high pressure rinses. On vertical
surfaces, apply the detergent starting at the bottom and work
your way upward. This method prevents the detergent from
sliding down and causing streaks. Begin high pressure rinsing
at the bottom and work your way upward. On particularly tough
stains, use a brush in combination with detergents and high
pressure rinsing.
1. Fill the detergent tank with cleaning solution.
NEVER turn the water supply off before turning the engine
off.
Depressurize System
To depressurize, turn engine off, turn water supply off and
squeeze gun trigger for at least 15 seconds after engine is
turned off.
! WARNING
NEVER disconnect the high pressure discharge hose from
the machine while the system is pressurized.
To reduce the risk of bodily injury or property damage, always
follow this procedure whenever spraying is stopped, when work
is completed, and before checking or repairing any part of the
system.
2. Insert the detergent suction hose (end with filter) into the
hole located in the center of the detergent tank lid.
1. Engage the trigger gun lock out.
3. Install the quick connect detergent nozzle (black) in the
spray wand. Detergent will only be drawn through the
pump when the black detergent nozzle is attached to the
end of the wand.
3. Shut off the water supply.
4. Be sure water supply is on. Start the engine. Pull the
trigger gun to spray the detergent solution.
! WARNING
NEVER use bleach in detergent tank. It will damage the
pump and void the warranty.
" NOTICE
The trigger gun will only draw detergent from the tank when
the black quick connect nozzle is installed in the wand.
" NOTICE
When spraying detergent, the detergent will be diluted
1:12. Approximately 621 mL (21 oz.) of detergent will be
consumed from the tank for every minute sprayed.
2. Turn the unit off.
4. Disengage the trigger safety latch and trigger the gun to
relieve pressure.
5. Re-engage the trigger safety latch.
6. Before overnight storage, long term storage, or
transporting unit, disconnect the water supply and turn off
the fuel supply valve.
Operating Tips
! CAUTION
Never operate your pressure washer without water.
! CAUTION
Never connect your pressure washer to a hot water supply.
Connecting your pressure washer to a hot water source will
significantly reduce the life of the pump and will void the
warranty.
15
MAINTENANCE
100310 - 3000 PSI PRESSURE WASHER
! CAUTION
Select the correct main jet part number corresponding to the
carburetor code found on your particular carburetor.
Running the unit for more than one minute without spraying
water causes heat to build up in the pump.
Carburetor
Code
In the event that the pump gets too hot, a thermal relief
valve will open to release the hot water. Running the unit
without spraying water can damage pump components and
will void the warranty.
P19-1-Z
P19-1-Y
P19-1-H
Stopping the Engine
Main Jet
Part Number
Standard
26.131017.00.Z
Altitude
26.131017.00.01.Z
Standard
26.131017.00.Y
Altitude
26.131017.00.01.Y
Standard
26.131017.00.H
Altitude
26.131017.00.01.H
Altitude
1067 m
(3500 ft.)
1. Turn the fuel valve to the “OFF” position.
2. Let the engine run until fuel starvation has stopped the
engine. This usually takes a few minutes.
3. Press the engine switch to the “OFF” position.
4. Depressurize system.
5. Turn off water supply and unplug all hoses. Never start or
stop the pressure washer unless the water supply is turned
on.
Important: Always ensure that the fuel valve and the engine
switch are in the “OFF” position when the engine is not in use.
" NOTICE
If the engine will not be used for a period of two (2) weeks
or longer, please see the Storage section for proper engine
and fuel storage.
! WARNING
Operation using the alternative main jet at elevations lower
than the recommended minimum altitude can damage the
engine. For operation at lower elevations, the standard
main jet must be used. Operating the engine with the wrong
engine configuration at a given altitude may increase its
emissions and decrease fuel efficiency and performance.
MAINTENANCE
Make certain that the pressure washer is kept clean and stored
properly. Only operate the unit on a flat, level surface in a clean,
dry operating environment. DO NOT expose the unit to extreme
conditions, excessive dust, dirt, moisture or corrosive vapors.
! WARNING
Never operate a damaged or defective pressure washer.
Operation at High Altitude
The density of air at high altitude is lower than at sea
level. Engine power is reduced as the air mass and air-fuel
ratio decrease. Engine power and output will be reduced
approximately 3½% for every 305 m (1000 ft.) of elevation
above sea level. This is a natural trend and cannot be changed
by adjusting the engine. At high altitudes increased exhaust
emissions can also result due to the increased enrichment of
the air fuel ratio. Other high altitude issues can include hard
starting, increased fuel consumption and spark plug fouling.
To alleviate high altitude issues other than the natural power
loss, Champion Power Equipment can provide a high altitude
carburetor main jet. The alternative main jet and installation
instructions can be obtained by contacting Customer Support.
Installation instructions are also available in the Technical
Bulletin area of the Champion Power Equipment internet site.
The part number and recommended minimum altitude for the
application of the high altitude carburetor main jet is listed
in the table below. In order to select the correct high altitude
main jet it is necessary to identify the carburetor model. For
this purpose, a code is stamped on the side of the carburetor.
! WARNING
Improper maintenance will void your warranty.
" NOTICE
Maintenance, replacement, or repair of emission control
devices and systems may be performed by any non-road
engine repair establishment or individual.
The owner/operator is responsible for all periodic maintenance.
Complete all scheduled maintenance in a timely manner.
Correct any issue before operating the pressure washer.
For service or parts assistance, contact our help line at
1-877-338-0999.
16
MAINTENANCE
100310 - 3000 PSI PRESSURE WASHER
Cleaning the Pressure Washer
! CAUTION
DO NOT spray the pressure washer with water.
Water can contaminate the fuel system and can enter the
engine through the cooling slots and damage the engine.
1. Use a damp cloth to clean exterior surfaces of the pressure
washer.
5. Add up to 0.6 L (0.6 qt.) of oil and replace oil fill cap/
dipstick. DO NOT OVERFILL.
6. Dispose of used oil at an approved waste management
facility.
" NOTICE
Once oil has been added, a visual check should show oil
about 1-2 threads from running out of the fill hole. If using
the dipstick to check oil level, DO NOT screw in the dipstick
while checking.
2. Use a soft bristle brush to remove dirt and oil.
3. Use an air compressor (25 PSI) to clear dirt and debris
from the pressure washer.
4. Inspect all air vents and cooling slots to ensure that they
are clean and unobstructed.
Cleaning Spray Nozzle
Detach the quick connect nozzle from the wand. Use a small
wire rod (paper clip) to loosen up any particles in the quick
connect nozzle and flush with water.
Cleaning and Adjusting the Spark Plug(s)
1. Remove the spark plug cable from the spark plug.
2. Use a spark plug socket tool (not included), or a
21 mm (13/16 in.) (not included) socket to remove the plug.
3. Inspect the electrode on the plug It must be clean and not
worn to produce the spark required for ignition
4. Make certain the spark plug gap is
0.7-0.8 mm (0.028-0.031 in.).
0.7 - 0.8 mm
0.028 - 0.031 in.
To prevent accidental starting, remove and ground spark plug
wire before performing any service.
5. Refer to the spark plug types in Specifications when
replacing the plug.
Changing the Engine Oil
6. Carefully thread the plug into the engine
Change oil when the engine is warm. Refer to the oil
specification to select the proper grade of oil for your operating
environment.
7. Use the spark plug socket tool (not included), or a
21 mm (13/16 in.) (not included) socket to install the plug.
1. Remove the oil drain plug with a 12 mm socket and
extension (not included).
2. Allow the oil to drain completely.
8. Attach the spark plug wire to the plug.
Cleaning the Air Filter
3. Replace the drain plug.
1. Using your fingers, unscrew the thumb screws of the top
holes of the air filter cover.
4. Remove oil fill cap/dipstick to add oil.
2. Remove the plastic outer casing.
3. Remove the foam element.
4. Wash in liquid detergent and water. Squeeze thoroughly dry
in a clean cloth.
5. Saturate in clean engine oil.
6. Squeeze in a clean, absorbent cloth to remove all excess
oil.
7. Place the filter in the assembly.
17
STORAGE
100310 - 3000 PSI PRESSURE WASHER
8. Reattach the air filter cover and using your fingers, insert
the thumb screws into the top and bottom holes of the air
filter cover. Screw until tight. Be sure not to over tighten.
Cleaning the Spark Arrester
1. Allow the engine to cool completely before servicing the
spark arrester.
2. Remove the four (4) screws holding the cover plate which
retains the end of the spark arrester to the muffler.
warranty. CPE recommends that you contact our service line at
1-877-338-0999 for all other service and/or adjustment needs.
Maintenance Schedule
Follow the service intervals indicated in the schedule below.
Service your pressure washer more frequently when operating
in adverse conditions. Contact our help line at 1-877-338-0999
to locate the nearest Champion Power Equipment certified
service dealer for your maintenance needs.
3. Remove the spark arrester screen.
EVERY 8 HOURS OR DAILY
4. Carefully remove the carbon deposits from the spark
arrester screen with a wire brush.
# Check oil level
# Clean around air intake and muffler
5. Replace the spark arrester if it is damaged.
6. Position the spark arrester in the muffler and attach with
the four (4) screws.
FIRST 5 HOURS
# Change oil
EVERY 50 HOURS OR EVERY SEASON
# Clean air filter
# Change oil if operating under heavy load or in hot
environments
EVERY 100 HOURS OR EVERY SEASON
! CAUTION
Failure to clean the spark arrester will result in degraded
engine performance.
" NOTICE
Federal and local laws and administrative requirements
indicate when and where spark arresters are required.
When ordered, spark arresters are required for operation
of this product in National Forest lands. In California, this
product must not be used on any forest-covered land,
brush-covered land, or grass-covered land unless the
engine is equipped with a spark arrester.
Adjusting the Governor
! WARNING
Tampering with the factory set governor will void your
warranty.
The air-fuel mixture is not adjustable. Tampering with the
governor can damage your pressure washer and will void your
#
#
#
#
#
Change oil
Clean/adjust spark plug
Check/adjust valve clearance*
Clean spark arrester
Clean fuel tank and filter*
EVERY 250 HOURS
# Clean combustion chamber*
EVERY 3 YEARS
# Replace fuel line*
* To be performed by knowledgeable, experienced owners or Champion Power
Equipment certified dealers.
STORAGE
Refer to the Maintenance section for proper cleaning
instructions.
Pressure Washer Storage
1. Allow the pressure washer to cool completely before
storage.
2. Turn off the fuel supply at the fuel valve.
18
STORAGE
100310 - 3000 PSI PRESSURE WASHER
3. Clean the pressure washer according to the instructions in
the Maintenance section.
4. Store the unit in a clean, dry area out of direct sunlight.
Engine Stored for Less than 30 Days
1. Allow the engine to cool completely before storage.
2. Clean engine according to the Maintenance section.
3. To extend the fuel storage life add a properly formulated
fuel stabilizer to the tank.
4. Ensure the fuel valve is in the “OFF” position.
5. Pour the antifreeze into the funnel, then pull on the engine
recoil starter to create suction in the pump housing. Pull
the recoil several times until antifreeze comes out of the
pump outlet.
! WARNING
Never store the pressure washer inside or next to appliances
where there is a source of heat or open flame, spark or pilot
light because they can ignite gasoline vapors.
DO NOT store a pressure washer near fertilizer or any
corrosive material.
Even with an empty gas tank, gasoline vapors could ignite.
Engine Stored for Over 30 Days
1. Add a properly formulated fuel stabilizer to the tank.
! DANGER
2. Run the engine for a few minutes so the treated fuel cycles
through the fuel system and carburetor.
Engine exhaust contains odorless and colorless carbon
monoxide gas.
3. Turn the fuel valve to the “OFF” position.
To avoid accidental or unintended ignition of the product
during periods of storage, the following precautions should
be followed:
4. Let the engine run until fuel starvation has stopped the
engine. This usually takes a few minutes.
5. The engine needs to cool completely before cleaning and
storage.
6. Clean the engine according to the Maintenance section.
7. Change the oil.
8. Remove the spark plug and pour about 1⁄2 oz. (14.9 mL) of
oil into the cylinder. Crank the engine slowly to distribute
the oil and lubricate the cylinder.
9. Reattach the spark plug.
Winter Storage
Protect your pressure washer parts from freezing.
1. Apply all storage instructions from previous sections.
– When storing the pressure washer for short or long
periods of time make sure that the engine switch and
the fuel valve are set in the "OFF" position.
" NOTICE
Our engines work well with 10% or less ethanol blend fuels.
When using blended fuels there are some issues worth
noting:
– Ethanol-gasoline blends can absorb more water than
gasoline alone.
– These blends can eventually separate, leaving water or a
watery goo in the tank, fuel valve and carburetor.
2. Make sure pressure washer hose is free of all water before
storing for winter.
– With gravity-fed fuel supplies, this compromised fuel
can be drawn into the carburetor and cause damage to
the engine and/or potential hazards.
3. In order to prevent the pump from freezing you will need to
insert RV antifreeze.
– There are only a few suppliers of fuel stabilizer that are
formulated to work with ethanol blend fuels.
4. You will need approximately 6 oz. (177.4 mL) of RV
antifreeze, a funnel, and approximately 12 in. (30.5 cm) of
garden hose or equivalent. See diagram below.
– Any damages or hazards caused by using improper fuel,
improperly stored fuel, and/or improperly formulated
stabilizers, are not covered by manufacturer's warranty.
It is advisable to always shut off the fuel supply, run the
engine to fuel starvation and drain the tank when the
equipment is not in use for more than 30 days.
19
SPECIFICATIONS
100310 - 3000 PSI PRESSURE WASHER
SPECIFICATIONS
Pressure Washer Specifications
Model .......................................................................... 100310
Max Pressure ............................................................3000 PSI
Max Volume ...............................................................2.5 GPM
Max Water Temperature .................................... 60º C (140º F)
Fuel Capacity ....................................................3.4 L (0.9 gal.)
Gross Weight .................................................34.9 kg (76.9 lb.)
Net Weight .......................................................31 kg (68.3 lb.)
Height ..........................................................97.2 cm (38.3 in.)
Width ...........................................................46.7 cm (18.4 in.)
Length.............................................................68 cm (26.8 in.)
Engine Specifications
Model ............................................................... YF168F-2-000
Displacement ................................................................196 cc
Type ...................................................................4-Stroke OHV
Fuel Specifications
Use unleaded gasoline intended for motor vehicle use with
a minimum octane rating of 85 or higher. Never use fuel
containing more than 10% ethanol. DO NOT USE E15 or E85.
DO NOT OVERFILL.
Gasoline Capacity ................................ 3.4 L (0.9 gal.)
Spark Plug Specifications
OEM Type ........................................... NHSP F6RTC
Replacement Type................... NGK BPR6ES or equivalent
Gap ............................... 0.7-0.8 mm (0.028-0.031 in.)
Valve Specifications
Intake Clearance .............. 0.13-0.17 mm (0.005-0.007 in.)
Exhaust Clearance ............ 0.18-0.22 mm (0.007-0.009 in.)
" NOTICE
A technical bulletin regarding valve adjustment procedures
is available at www.championpowerequipment.com.
Start Type ....................................................................Manual
Oil Specifications
Important Message About Temperature
DO NOT OVERFILL.
Your Champion Power Equipment product is designed and rated
for continuous operation at ambient temperatures up to 40°C
(104°F). When your product is needed it may be operated at
temperatures ranging from 5°F (-15°C) to 122°F (50°C) for
short periods of time. If exposed to temperatures outside this
range during storage, it should be brought back within this
range before operation. In any event, the product must always
be operated outdoors, in a well-ventilated area and away from
doors, windows and vents.
Type ............................................ *See chart below
Capacity ............................................0.6 L (0.6 qt.)
Degrees Celsiusº (Outside)
Full Synthetic 5W-30
Degrees Fahrenheitº (Outside)
" NOTICE
Weather will affect engine oil and engine performance.
Change the type of engine oil used based on weather
conditions to suit the engine needs.
20
12
30
24
23
29
25
22
12
28
27
26
32 31
28
21 20 19
32
31
37
18 17
29
12
33
34
35
16
36
12
23
15
14
30
12
13
38
18
39
10
11
9
8
5
6
4
3
7
2
1
100310 - 3000 PSI PRESSURE WASHER
SPECIFICATIONS
Parts Diagram
21
SPECIFICATIONS
100310 - 3000 PSI PRESSURE WASHER
Parts List
#
Part Number
Description
Qty.
#
Part Number
1
22
254.201600.00.78
Mounting Plate
1
23
1.5789.0615
Flange Bolt M6 x 15
6
24
254.200012.03.78
Hose Hanger
1
25
254.250100.00
High-Pressure Hose,
25 ft.
1
26
252.201300.00
Pin
2
1
26.111
Engine
2
2.14.001
Key, SQ
4.78 x 4.78 x 40
1
3
2.08.010
Bolt 5/16-24 x 22
4
4
1.93.08
Lock Washer Ø8
4
5
252.251003.00
Inlet Filter Gasket
1
6
254.251000.01
Pump Body
1
7
254.250100.10
Detergent Hose,
35.4 in.
1
Description
Qty.
27
254.201100.08.78
Frame
1
28
1.6182.10
Lock Nut M10
2
29
254.201701.03.48
12 in. Wheel, Yellow
2
8
254.252200.00
Wand
1
30
2.08.007
Bolt M10 x 82
2
9
254.252100.00.2
Handle, Gun
1
31
1.6177.1.08
Lock Nut M8, Flange
8
10
1.5783.0645
Bolt M6 x 45
2
11
254.200012.05.2
Trigger Gun Holder
1
32
252.201200.00
Vibration Mount,
Engine
2
12
1.6177.1.06
Lock Nut M6, Flange
12
83.201400.01
1
Vibration Mount,
Support Leg
2
254.252300.05
Nozzle "Detergent",
65400
33
34
1.5789.0620
Flange Bolt M6 x 20
2
254.250203.01
Cap, Detergent Tank
2
13
14
254.252300.09
Nozzle "40", 40028
1
35
15
254.252300.08
Nozzle "25", 25028
1
36
254.250200.01
Detergent Tank, Left
1
16
254.252300.06
Nozzle "0", 00028
1
37
254.250200.02
Detergent Tank, Right
1
17
252.201400.01
Sheath, Nozzle
4
254.200800.01.2
1.5789.0615.1
7
Decorative Sheet,
Down
1
18
Flange Bolt M6 x 15,
Black
38
39
2.03.038
Curved Washer
2
19
254.200800.00.2
Decorative Sheet, Up
1
20
2.08.139
Bolt M6 x 35
2
21
254.200701.06.78
Handle, Frame
1
22
30
1
133
132
108
131
130
121
11
2
14
129
128
3
127
4
126
5
134
15
6
135
7
20
16
136
8
21
125
9
10
22
23
17
20
11
18
24
112
99
12
25
112
99
79
19
124
46
79
123
122
13
26
27
45
44
43
42
41
40
28
29
137
42
118
117
116
50
49
48
47
31
11
51
32
109
33
53
54
108
111
112
113
114
115
55
107
34
52
56
106
110
119
35
57
36
58
104
59
61
62
105
103
60
69
63
37
64
68
65
66
70
38
71
67
72
74
1
75
73
76
84
77
78
83
79
39
89
82
80
19
97
90
81
85
86
120
91
87
92
93
94
88
98
96
100 101 102
95
100310 - 3000 PSI PRESSURE WASHER
SPECIFICATIONS
Engine Parts Diagram
23
SPECIFICATIONS
100310 - 3000 PSI PRESSURE WASHER
Engine Parts List
#
1
Part Number
Description
Qty.
#
Part Number
Description
Qty.
1
36
22.031000.00.48
Oil Dipstick Assembly,
Yellow
37
24.030007.00
Cover, Crankcase
1
1
38
1.5789.0832.0.8
Flange Bolt M8 x 32
6
Rope Ø5 x 1550
1
39
22.031000.01.48
Oil Filter Cap, Yellow
1
21.061001.01
Reel, Recoil Starter
1
40
23.110005.01
Spring, Throttle Return
1
45.060003.00
Spring, Ratchet
2
41
21.110003.00
Arm, Governor
1
42
1.6177.06
Flange Nut M6
3
43
2.03.021.1
Washer
Ø6.4 x Ø13 x 1, Black
1
1.5789.0608
Flange Bolt M6 x 8
5
2
22.061100.00.2
Cover, Recoil Starter,
Black
1
3
21.061005.00
Spring, Recoil Starter
4
2.10.003
5
6
7
45.060002.00
Starter Ratchet, Steel
2
8
45.060009.00
Spring, Ratchet Guide
1
9
45.060007.00
Ratchet Guide
1
10
45.060008.00
Screw, Ratchet Guide
1
44
21.110001.00
Shaft, Governor Arm
1
11
1.5789.0612
Flange Bolt M6 x 12
10
45
22.123000.02
Ignition Coil, Shield
1
12
24.080100.01.48
Fan Cover, Yellow
1
46
1.5789.0625
Flange Bolt M6 x 25
2
13
2.05.002
Clamp Ø9.5 x 5
1
47
23.110006.00
Rod, Governor
1
23.110007.00
Spring, Governor
1
14
21.061300.00
Handle, Recoil, Soft
1
48
15
2.02.006
Nut M14 x 1.5
1
16
21.060001.01
Pulley, Starter
1
49
2.08.040
Bolt M6 x 21, Governor
Arm
1
17
23.080001.00
Cooling Fan
1
50
21.110008.00
Pin, Shaft
1
18
24.120100.06
Flywheel
1
51
24.111008.01
1
2.11.001
Oil Seal
Ø25 x Ø41.3 x 6
Grip Sheath, Speed
Governor
2
52
24.111000.01
Control Assembly
1
53
25.040013.00
Lifter, Valve
2
2.03.020.1
Washer
Ø6.2 x Ø15 x 0.5,
Black
2
54
2.04.001
Dowel Pin Ø9 x 14
2
55
26.041000.01
Camshaft
1
56
2.14.012
Woodruff Key
4 x 7.5 x 19
1
57
26.050005.00
Piston
1
58
23.050003.00
Pin, Piston
1
59
2.09.001
Circlip Ø18 x Ø1
2
60
26.050303.00
Ring, Oil
1
61
26.050302.00
Ring, Second Piston
1
62
26.050301.00
Ring, First Piston
1
63
26.030009.00
Gasket, Cylinder Head
1
64
2.04.003
Dowel Pin Ø10 x 14
2
65
23.040002.00
Valve, Intake
1
66
23.040006.00
Valve, Exhaust
1
67
26.080400.00
Air Guide, Lower
1
68
2.15.002(F6RTC)
Spark Plug F6RTC
1
69
1.5789.0860
Flange Bolt M8 x 60
4
70
23.040017.00
Oil Seal, Valve
2
71
21.040003.00
Spring, Valve
2
19
20
21
21.110100.00
Gear, Governor
1
22
21.110013.00
Shaft, Governor Gear
1
23
21.110011.00
Clip, Governor Gear
1
24
21.110012.01
Bushing, Govornor
Gear, Steel
1
25
23.080600.00
Air Guide, Right
1
26
2.08.037
Drain Bolt
M10 x 1.25 x 25
2
27
2.03.016
Washer
Ø10 x Ø16 x 1.5,
Drain Bolt
2
28
26.030100.00
Crankcase
1
29
21.120400.01
Diode Assembly
1
26.131017.00
Main Jet, Standard
1
26.131017.00.01
Main Jet, Altitude
/
31
21.127000.02
Oil Level Sensor
1
32
23.050200.00
Connecting Rod
1
33
25.050100.03
Crankshaft
1
34
1.276.6205
Bearing 6205
2
72
21.040007.00
Retainer, Exhaust
Valve Spring
1
35
24.030008.00
Gasket, Crankcase
Cover
1
73
21.040001.00
Retainer, Intake Valve
Spring
1
30
24
SPECIFICATIONS
100310 - 3000 PSI PRESSURE WASHER
#
Part Number
Description
Qty.
74
21.040008.00
Rotator, Exhaust Valve
1
75
24.040202.00
Shaft, Rocker Arm
1
76
22.040009.00
Rocker Arm
2
77
22.040012.00
Screw, Valve
Adjustment
2
#
Part Number
Description
Qty.
115 24.091600.01
Screw Cap, Air Clean
Cover
2
116 2.12.001
Buffer Ø7.5 x 7.5
1
117 2.06.006
Clamp Ø7 x Ø1
1
118 24.070014.02
Pipe, Reversal Valve
1
78
21.040021.00
Nut M6 x 0.5, Lock
2
119 24.091000.02
Air Cleaner Assembly
1
79
1.97.1.06
Washer Ø6
6
120 24.101000.00
Muffler Assembly
1
80
1.6177.1.06
Flange Nut M6
2
121 22.061000.00
Recoil Assembly
1
81
24.040201.00
Retainer, Rocker Arm
1
122 24.070100.02
Cap, Fuel Tank
1
82
23.040010.00
Bolt, Rocker Arm
2
123 81.070301.00
Fuel Filter, Fuel Tank
1
83
24.040004.00
Guide Plate, Push Rod
1
124 1.5789.0633
Flange Bolt M6 x 33
1
84
23.040005.00
Push Rod
2
125 24.071000.01
Fuel Tank
1
85
21.020002.01
Gasket, Cylinder Head
Cover
1
126 111.070300.01
Fuel Filter, Fuel Pipe
1
127 2.06.018
Clamp Ø10.5 x b8
1
86
24.021000.00
Cover, Cylinder Head
1
128 24.070400.00
Fuel Valve
1
87
21.020001.00
Breather Tube
1
129 24.070011.01
Pipe Ø4.5 x (30 + 30)
1
88
1.5789.0615
Flange Bolt M6 x 15
4
130 24.070010.00
Veil, Fuel Tank
1
89
2.01.010
Stud Bolt M8 x 35
2
131 5.1010.003.3
Ignition Switch, Red
1
90
26.100001.00
Gasket, Exhaust Pipe
1
132 24.070001.00
Fuel Knob
1
91
1.16674.0510
Flange Bolt M5 x 10
2
133 1.818.0412
Bolt M4 x 12
1
92
1.848.05
Washer Ø5
2
134 1.16674.0512.2
Flange Bolt M5 x 12
1
93
1.93.05
Lock Washer Ø5
2
135 2.06.007
Clamp Ø8 x b6
3
94
24.101202.00
Muffler Protector
1
136 24.070011.00
46.101300.05
1
Fuel Pipe
Ø4.5 x Ø9.5 x 230
1
95
Spark Arrester
Assembly
137 23.120700.02
Change Wire Flameout
1
96
1.818.0406
Screw M4 x 6
4
97
1.9074.4.0510
Screw/Washer
Assembly M5 x 10
2
98
24.101000.00
Muffler Assembly
1
99
1.93.06
Lock Washer Ø6
6
100 1.6175.08
Nut M8
2
101 1.848.08
Washer Ø8
2
102 1.93.08
Lock Washer Ø8
2
103 26.010100.00
Cylinder Head
1
104 2.01.009
Stud Bolt M6 x 110
2
105 24.130002.00
Gasket, Insulator
1
106 23.130001.00
Insulator, Carburetor
1
107 22.130003.00
Gasket, Carburetor
1
Carburetor
1
109 21.130004.00
Gasket, Air Cleaner
1
110 21.130100.00
Choke Handle
1
111 24.091100.01
Base, Air Cleaner
1
112 1.5789.0620
Flange Bolt M6 x 20
5
113 24.091003.02
Element, Air Cleaner
1
114 24.091200.02
Cover, Air Cleaner
1
108
26.131000.00
26.131000.02
25
SPECIFICATIONS
100310 - 3000 PSI PRESSURE WASHER
Troubleshooting
Problem
Cause
Solution
No fuel.
Add fuel.
Faulty spark plug.
Replace spark plug.
Pressure washer will not start;
Low oil level.
Pressure washer starts but runs
roughly.
Fill crankcase to the proper level. Place
pressure washer on a flat, level surface.
Choke in the wrong position.
Adjust choke.
Spark plug wire loose.
Attach wire to spark plug.
Pressure washer gallops.
Engine governor defective.
Contact the help line.
Water supply is restricted.
Check hoses for leaks, blockage, kinks.
Garden hose is too small.
Replace with 5/8 in. garden hose or larger.
Garden hose inlet filter is clogged.
Remove garden hose, clean filter and
rinse out.
Not enough inlet water.
Turn garden hose water on full force.
Poor inlet water supply.
Turn garden hose water on full force.
Check hose for leaks, blockage, or kinks
Garden hose inlet filter is clogged.
Remove garden hose, clean filter and
rinse out
Spray nozzle is obstructed.
Remove particles with small wire rod
(see maintenance section in manual)
Pump is sucking air.
Check all hoses and fittings, make sure
they are securely tightened down and
fastened. Turn off engine and purge pump
by squeezing trigger gun until a steady
stream of water flows
Detergent is too thick
Dilute detergent
Spray wand has high pressure quick
connect nozzle installed
Detergent only works with low pressure
quick connect nozzle (black)
Detergent hose is not connected to the
pump housing
Check connection.
Spray nozzle is obstructed
Clean nozzle and remove debris
Filter on detergent hose is clogged
Clean with warm water or replace
Chemical Injector valve (inside pump)
partially blocked or stuck
Quickly pull and release the gun trigger
4-5 time to clear the chemical injector
valve
Pressure washer will not start.
Unit does not reach high pressure.
Spray pressure varies from high to low.
Low pressure detergent wash is not
functioning properly.
Detergent tube not connected to the brass Install detergent tube to detergent injector
fitting on the pump outlet
inlet near pump outlet
Loose fittings
Tighten
Missing/worn-out rubber washer
Replace rubber washer
Spray wand leaks
Spray wand not properly attached
Tighten all connections
Can't pull recoil
Pump will build pressure with each pull
Pull gun trigger after 2 pulls of recoil, to
release pump pressure
Garden hose connection leaks.
For further technical support:
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
26
WARRANTY
WARRANTY*
CHAMPION POWER EQUIPMENT
2 YEAR LIMITED WARRANTY
Warranty Qualifications
Champion Power Equipment (CPE) will register this warranty upon
receipt of your Warranty Registration Card and a copy of your sales
receipt from one of CPE’s retail locations as proof of purchase.
Please submit your warranty registration and your proof of purchase
within ten (10) days of the date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the mechanical and
electrical components will be free of defects in material and
workmanship for a period of two years (parts and labor) from
the original date of purchase and 180 days (parts and labor) for
commercial and industrial use. Transportation charges on product
submitted for repair or replacement under this warranty are the sole
responsibility of the purchaser. This warranty only applies to the
original purchaser and is not transferable.
Do Not Return The Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will troubleshoot any issue
via phone or e-mail. If the problem is not corrected by this method,
CPE will, at its option, authorize evaluation, repair or replacement
of the defective part or component at a CPE Service Center. CPE
will provide you with a case number for warranty service. Please
keep it for future reference. Repairs or replacements without prior
authorization, or at an unauthorized repair facility, will not be covered
by this warranty.
Warranty Exclusions
This warranty does not cover the following repairs and equipment:
Normal Wear
Products with mechanical and electrical components need periodic
parts and service to perform well. This warranty does not cover repair
when normal use has exhausted the life of a part or the equipment as a
whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor if the product is
deemed to have been misused, neglected, involved in an accident,
abused, loaded beyond the product’s limits, modified, installed
improperly or connected incorrectly to any electrical component.
Normal maintenance is not covered by this warranty and is not
required to be performed at a facility or by a person authorized by
CPE.
Other Exclusions
This warranty excludes:
– Cosmetic defects such as paint, decals, etc.
– Wear items such as filter elements, o-rings, etc.
–
–
Accessory parts such as starting batteries, and storage covers.
Failures due to acts of God and other force majeure events
beyond the manufacturer’s control.
– Problems caused by parts that are not original Champion Power
Equipment parts.
When applicable, this warranty does not apply to products used for
prime power in place of a utility.
Limits of Implied Warranty and Consequential Damage
Champion Power Equipment disclaims any obligation to cover
any loss of time, use of this product, freight, or any incidental
or consequential claim by anyone from using this product. THIS
WARRANTY AND THE ATTACHED U.S. EPA, CARB and/or ECCC
EMISSION CONTROL SYSTEM WARRANTIES (WHEN APPLICABLE)
ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE.
A unit provided as an exchange will be subject to the warranty of the
original unit. The length of the warranty governing the exchanged
unit will remain calculated by reference to the purchase date of the
original unit.
This warranty gives you certain legal rights which may change from
state to state or province to province. Your state or province may also
have other rights you may be entitled to that are not listed within this
warranty.
Contact Information
Address
Champion Power Equipment, Inc.
Customer Service
12039 Smith Ave.
Santa Fe Springs, CA 90670 USA
www.championpowerequipment.com
Customer Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
info@championpowerequipment.com
Fax no.: 1-562-236-9429
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
24/7 Tech Support: 1-562-204-1188
*Except as otherwise stipulated in any of the following enclosed Emission Control System Warranties (when applicable) for the Emission Control System: U.S.
Environment Protection Agency (EPA), California Air Resources Board (CARB) and/or Environment and Climate Change Canada (ECCC).
Champion Power Equipment, Inc (CPE) and Environment and Climate Change Canada (ECCC)
Emission Control System Warranty
Your Champion Power Equipment (CPE) engine complies with Environment and Climate Change Canada
(ECCC) emission regulations.
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
CPE is pleased to explain the Emission Control Systems Warranty on your 2017 small off-road engine.
New engines must be designed, built and equipped, at the time of sale, to meet ECCC regulations for
small non-road engines. CPE must warrant the emission control system on your small off-road engine for
the period of time listed below, provided there has been no abuse, neglect, unapproved modification, or
improper maintenance of your small off-road engine.
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition
system, catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other
emission related assemblies. Where a warrantable condition exits, CPE will repair your small off-road
engine at no cost to you including diagnosis, parts and labour.
MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:
This emission control system is warranted for two years, subject to provisions set forth below. If, during
the warranty period, emission related part on your engine is defective in materials or workmanship, the
part will be repaired or replaced by CPE.
OWNER WARRANTY RESPONSIBILITIES:
As the small off-road engine owner, you are responsible for the performance of the required maintenance
listed in your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance
on your small off-road engine, but CPE cannot deny warranty solely for the lack of receipts or for your
failure to ensure the performance of all scheduled maintenance.
As the small off-road engine owner, you should however be aware that CPE may deny you
warranty coverage if your small, off-road engine or a part has failed due to abuse, neglect,
improper maintenance or unapproved modifications.
You are responsible for presenting your small off-road engine to an Authorized CPE service outlet, CPE
dealer or CPE, Santa Fe Springs, CA., USA as soon as a problem exists. The warranty repairs should be
completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact:
Champion Power Equipment, Inc.
Customer Service
12039 Smith Ave.
Santa Fe Springs, CA 90670
USA
Tel: 1-877-338-0999
tech@championpowerequipment.com
EMISSION CONTROL SYSTEM WARRANTY
The following are specific provisions relative to your Emission Control System Warranty
Coverage.
Emission Control System Warranty (ECS Warranty):
1. APPLICABILITY: The ECS Warranty Period shall begin on the date the new engine or equipment is
delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
2. GENERAL EMISSIONS WARRANTY COVERAGE
CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent
purchaser that each of its small off-road engines is:
a. Designed, built and equipped so as to conform at the time of sale with applicable regulations
under the Canadian Environmental Protection Act, 1999 (CEPA 1999).
b. Free from defects in materials and workmanship that cause the failure of a warranted part to be
identical in all material respects to the part as described in the engine manufacturer’s application for
certification for a period of two years.
3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS
FOLLOWS:
a. Any warranted part that is not scheduled for replacement as required maintenance in the
Owners Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS
Warranty Period, it shall be repaired or replaced by CPE according to Subsection “d” below. Any such
part repaired or replaced under the ECS Warranty shall be warranted for any remainder of the ECS
Warranty Period.
b. Any warranted, emissions-related part which is scheduled only for regular inspection as
specified in the Owners Manual shall be warranted for the ECS Warranty Period. A statement in such
written instructions to the effect of “repair or replace as necessary”, shall not reduce the ECS Warranty
Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder
of the ECS Warranty Period.
c. Any warranted, emissions-related part which is scheduled for replacement as required
maintenance in the Owner’s Manual shall be warranted for the period of time prior to the first scheduled
replacement point for that part. If the part fails prior to the first scheduled replacement, the part shall be
repaired or replaced by CPE according to Subsection “d” below. Any such emissions-related part repaired
or replaced under the ECS Warranty, shall be warranted for the remainder of the ECS Warranty Period
prior to the first scheduled replacement point for such emissions-related part.
d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall
be performed at no charge to the owner at a CPE Authorized Service Outlet.
e. The owner shall not be charged for diagnostic labour which leads to the determination that a
part covered by the ECS Warranty is in fact defective, provided that such diagnostic work is performed at
a CPE Authorized Service Outlet.
f. CPE shall be liable for damages to other original engine components or approved modifications
proximately caused by a failure under warranty of an emission-related part covered by the ECS Warranty.
g. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emissionrelated parts sufficient to meet the expected demand for such emission-related parts.
h. Any CPE Authorized and approved emission-related replacement part may be used in the
performance of any ECS Warranty maintenance or repair and will be provided without charge to the
owner. Such use shall not reduce CPE’s warranty obligation.
i. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such
use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. CPE
shall not be liable hereunder for failures of any warranted parts of a
CPE engine caused by the use of such an unapproved add-on or modified part.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list
applicable to the engine)
Systems covered by this warranty
Fuel Metering System
Air Induction System
Ignition System
Exhaust System
Miscellaneous Parts
Evaporative Emissions
Parts description
Fuel regulator, carburetor and internal parts
Air cleaner, intake manifold
Spark plug and parts, magneto ignition system
Exhaust manifold, catalytic converter
Tubing, fittings, seals, gaskets, and clamps
associated with these listed systems.
Fuel tank, fuel cap, fuel line, fuel line fittings, clamps,
pressure relief valves, control valves, control
solenoids, electronic controls, vacuum control
diaphragms, control cables, control linkages, purge
valves, vapour hoses, liquid/ vapour separator,
carbon canister, canister mounting brackets,
carburetor purge port connector
TO OBTAIN WARRANTY SERVICE:
You must take your CPE engine or the product on which it is installed, along with your warranty
registration card or other proof of original purchase date, at your expense, to any Champion Power
Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE
product during his normal business hours. Claims for repair or adjustment found to be caused solely by
defects in material or workmanship will not be denied because the engine was not properly maintained
and used.
If you have any questions regarding your warranty rights and responsibilities, or to obtain
warranty service, please write or call Customer Service at Champion Power Equipment, Inc.
Champion Power Equipment, Inc.
12039 Smith Ave.
Santa Fe Springs, CA 90670
USA
1-877-338-0999
Attn: Customer Service
tech@championpowerequipment.com