ref prospekt metrac E 1011.indd

METRAC
AGRICULTURE
Metrac X-series
Excellent on slopes.
Soil conserving. Safe.
SINCE 1910
T E C H N O L O G Y
A T
I T S
B E S T
REFORM Metrac
The all round tool for
mountain agriculture.
The REFORM Metrac is a mountain agricultural two axle mower designed for extreme slopes. It is
distinguished by cutting edge technology and highest efficiency. With its outstanding slope capability,
combined with highest soil protection, the Metrac provides unique work comfort. REFORM Metrac have
been built since 1965.
The benefits at a glance:
Powerful, thrifty 4 cylinder diesel engines
Multi function lever for highest operating comfort*
Pre-selectable differential locks with 100% locking efficiency
Switchable four wheel drive
Depending on the area of use: Speed change gearbox
or hydrostatic drive
4 steering modes: 4 wheel steering, front, rear and
crab steering
Low dead weight and low centre of gravity
Slope capable, soil protecting low pressure
tyres
Permanent ground contact of all 4 wheels
through oscillating front axle (central joint)
Hydrostatic steering
2 full attachment areas with powerful
linkages
Weight compensation and vibration damping*
Power shift PTO
Axle guided, trailing front linkage
*not for G3
The Mountain Pro in Action!
Cutting edge technology and safety.
3
The large-size single disc dry clutch for the drive
in the G models and the PTO drive in the H models
ensures full power transmission and long service life.
The PTO drive of the G models is switched electrohydraulically via a multi disc clutch (G3 manually).
4
Mechanical transfer gear with PTO clutch
The drive goes from the engine via the clutch to the
mechanical transfer gear and from there to the front
and rear PTOs. In the G models, the force flows from
the mechanical transfer gear via a cardan shaft to
the speed change gearbox.
The Reform
Metrac Chassis.
Two-axle mowers are designed as automotive tool carriers for
safe and soil protecting work in mountainous terrain. The tried and
tested Reform Metrac chassis is divided into a front and a rear axle
section which are connected by a pivoting centre joint. On this robust
chassis, a wide range of attachments can be mounted such as rotary
disc mower, side delivery belt rake, rotary tedder, flail mower, and many
more.
1
9
1
10
2
3
4
G4X – H7X
2
Robust driving/steering axles with planet
gear final drives deliver high pulling force
and protect the drive train. The drive shafts are
exposed to lower forces, therefore they can be
built in a lighter design.
1 internal gear
2 planet gear
3 internal sun gear
4 planet gear carrier
Hydraulic lateral displacement
Centre joint and oscillating axle
Between the oscillating front axle
and the rear axle, the pivoting
centre joint ensures constant
ground contact of all 4 wheels
and guarantees safe driving
in any situation. You get full power
transmission and optimal soil
protection also in rough terrain.
Rotating angle front linkage
G4X – H7X
9
9
190 mm
400 mm
Exterior
electric controls
1
The strong, axle guided front linkage (9) provides best
contour following through pivot points that are located
far behind the front axle. The standard hydraulic (G3) or
electro-hydraulic weight compensation provides higher
traction and better climbing capability combined with highest
contour following and soil protection, Lateral side shift: Even
better slope capability by displacing the centre of gravity.
facilitates working close to obstacles and makes mounting of
attachments easier.
In the G models, the PTO (10) is driven via a multi disc clutch,
and via a single disc dry clutch in the hydrostat models.
The high efficiency of the electro hydraulically (not in G3)
power shiftable PTO with 540 rpm facilitates the efficient use
of attachments.
5
The four wheel drive (front drive switchable) facilitates maximum power
transmission to the ground by optimal distribution of the driving force to both axles.
With 4 wheel steering activated, the front and rear wheels run exactly in the same
track, ensuring absolutely tension free traction of all 4 wheels.
6
The robust 3 point rear linkage (option) is equipped with double acting cylinders
(G3 also single acting). The high lifting forces also permits the use of heavy
attachments. A particularly helpful feature for mounting attachments conveniently
and fast is, as in the font linkage, the standard exterior electric control of the
linkages (not in G3). Optional the lower links can be with hook ends.
7
Cab mount
Engine mount
Centre tube with engine mount and cab mount. The centre
tube provides the robust link between front and rear axle. Cab
and engine are mounted on 4 rubber mounts each to dampen
vibration. Vibrations are neutralised at their very source.
3
4
8
2
11
7
The rear PTO is electro hydraulically
switchable and ensures the soft
starting of attachments due to the soft
start system (does not apply to G3:
rear gearbox PTO).
5
8
6
12
Use the full power with the mechanic speed change gearbox (11) in the Metrac
G-series. The synchronised shuttle gearbox ensures exact and safe gear change in any
situation. G4 X – G7 X optionally with creep speed group.
Hydrostatic drive (12) with variable pump and variable motor in the two axle mowers of
the H series – this comfort is with a capital C. The hydrostatic drive with 4 speed ranges
provides continuous adaptation of the drive speed to the various working conditions and
allows for soft, smooth starting also on slopes. The permanent transmission of power
generates additional safety on slopes.
Large tank (not shown)
The large polyethylene tank holds enough fuel for a whole working day without refilling.
REFORM Metrac
2 full attachment areas for a
wide range of attachments.
The chassis of the Reform two axle mowers is designed for mounting attachments both in front and in the rear.
Thus two full attachment areas for a large number of implements are available. The robust linkage with standard mounting
points facilitate quick mounting and removing of attachments such as rotary disc mower, side delivery belt rake, dump bucket,
and many more, making the system a versatile and universal tool.
1
Front linkage with front PTO
Rotary disc mower, twin blade, side delivery belt rake,
flail mower, front end loader, front collecting fork,
snow plough, snow blower, etc.
2
Rear linkage with rear PTO,
trailer hitch
Rotary tedder, rotary swather, dump bucket, fertiliser spreader,
trailer, baler, drag hose manure application, etc.
1
For a wide range of everyday requirements.
2
1 Front end loader
2 e.g. rear weight
1 Rotary disc mower
2 e.g. conditioner
1 Side delivery belt rake
1 Flail mower
1 Rotary mower
2 Rotary tedder
2 Dump bucket
1 Snow blower
Metrac in action all your round
Protecting man and machine
REFORM weight transfer
and vibration damping.
kg
Front axle
The mower follows the ground contours without
changing the weight compensation pressure.
Electro hydraulic weight compensation – in G4 X – H7 X
The front linkage with electro hydraulic weight transfer allows
the driver to control the ground pressure of front attachments
conveniently from the cab. The hydraulic system transfers a
large part of the attachment’s ground pressure to the front
wheels using a specified, adjustable residual pressure in the
hydraulic cylinders. The mower virtually hovers above the
ground, requiring less pushing force and engine power, gets
increased climbing capability and traction, and goes easy on
the turf.
The digital display shows the set
compensation pressure that you pre select
with the push of a button. The electronic
system controls the recharging of the
accumulators, ensuring that the selected
compensation pressure is maintained.
Hydraulic vibration damping (optional / standard)*
All vibrations caused by heavy attachments during fast driving
are neutralised, minimising impact load. This means more
comfort and safety, and less wear during work for your Metrac
including attachment. The switchable vibration damping (also
called vibration absorbtion) is available for the front linkage
and/or the rear linkage.
The impact load is minimised
by gas pressure accumulators.
Gas pressure accumulators absorb large
part of the vibrations that occur during
driving with heavy attachments, especially
in road driving.
*see technical specification
Your benefits at a glance:
Electro hydraulic weight compensation:
• Increased climbing and slope capability.
• More traction through weight transfer to the front axle.
• Constant weight compensation for optimal ground following and
protection.
• Great convenience by easy, straightforward operation.
• Weight compensation pressure pre selectable via buttons.
• Setting range from 6 to 120 bar (1 bar increments or quick sweep).
• Permanent desired/actual comparison of the set and the actual
compensation pressure.
• An indicator light in the dashboard signals when the weight
compensation is active.
• Protection of the hydraulic system and the machine.
• Switchable to the rear linkage (option).
Hydraulic vibration damping:
• Provides smooth driving also with heavy attachments.
• Comfortable driving with low machine wear.
• Reduces vibration build up in the vehicle during fast road travel
with mounted attachment.
• Greatly increased driving comfort in road traffic.
• Easier travel to and from the work area.
• Forces caused by sudden jolts, which are transferred to the axle
by the top and lower links, are reduced.
• Damping of vibrations transferred from the ground to an attachment.
• Vibrations caused by uneven ground are absorbed.
• Damping effect also in the cab.
• The vibration damping feature is switchable.
REFORM Metrac
The smart
4 wheel steering system!
Up and down the hills with 4 wheel steering
The hydrostatic steering system with four steering
modes as standard equipment is the crowning
achievement in this chassis concept. The steering
mode can be switched conveniently by the
push of a button, even during
driving.
The "thinking" steering system
Sensors report the straight alignment of the
wheels to the steering control unit, which
enables the fully automatic switch of
steering modes, e.g., from front to 4 wheel
steering and vice versa.
The 4 steering modes
1
Front steering
2
Rear steering
1 Front steering
• For driving on roads, for safe, stable driving at high speeds.
• For working with rear mounted attachments or trailer operation.
2 Rear steering
Used mainly on level to moderately sloped terrain. With rear steering, the
direction of front mounted attachments can be better controlled than with
front steering. Moreover, the font attachment is not subject to lateral "shift"
during steering, allowing for much smoother and more consistent work.
3 4 wheel steering
The special features of the original Reform 4 wheel steering:
• High manoeuvrability in the tightest of spaces.
• Front and rear wheels are turned at the same angle and run exactly
3
4 wheel steering
4
Crab steering
in the same track.
• Maximum soil protection by even, absolutely tension free traction of all 4
wheels.
• Quick and fully automatic switching of steering modes with the push of a
button – also during driving.
• Better efficiency through tighter turning circles.
4 Crab steering
Front steering is used while the rear wheels are turned at an angle;
this results in a lateral offset during driving.
• For safe work in extreme contours through a shift in the centre of gravity.
• Working along ditches and fences; the rear wheels stay at a distance.
• Convenient for spreading at boundaries with 3 point rotary tedder.
• Soft ground is protected since each wheel runs in its separate track.
REFORM Metrac G3
The climber with soft paws.
Enter the world of two axle mowers!
The Metrac G3 features a high degree of mature technology, paired with
very easy operation. Combined with a twin blade mower, the Metrac G3 is an
especially lightweight and cost efficient working combination with unbeatable
terrain capability. Thanks to good engine output and the power shiftable front
PTO, the G3 is also particularly efficient with a rotary disc mower.
• Powerful technology with high efficiency.
• Uncomplicated, robust technology
• Particularly low weight for maximum terrain mobility
• Dead weight of only approx. 1400 kg
• Front linkage with hydraulic weight transfer
• 4 wheel steering system by the push of a button
• 4 steering modes for unbeatable manoeuvrability
• Switchable 4 wheel drive
(front wheel drive can be deactivated)
• Power shiftable front PTO
• Very good power to weight ratio
(only 31.9 kg/hp)
• Low centre of gravity, large footprint
• 26" wheels – optionally 29"
• Highest soil protection and agility
Even more power
The Metrac G3 features a powerful 4 cylinder diesel engine
with 44 hp (32.1 kW) at 2800 rpm – for even more power
reserves when working with the rotary disc mower. The
large, well sealed bonnet, being a highly efficient dust filter,
increases maintenance intervals for radiator and fan.
Hydraulic weight compensation
The pre selectable weight compensation pressure is set via a
rotary knob and shown at the pressure gauge. If needed, the
system is recharged at the push of a button in a matter of
seconds.
Even more comfortable
The driver rollover protection frame with curved windscreen
and large viewing area offers much head room and
moving space. The Metrac G3 comes standard with a
right side window and rear window. The tinted window
glass reduces sun radiation and provides high working
comfort. The straightforwardly organised dashboard, with
clearly structured indicator and warning lights, provides
permanently essential information.
The generously sized cab
Sit down on the ergonomic comfort seat. All
levers and pedals are ergonomically arranged in
functional groups. Straight switching travels of
the 8F/8R shuttle gearbox provide fast and safe
switching even on slopes.
For optimal night-time view
the Metrac G3 can be equipped with
auxiliary lights, and also with a rotating
warning light for better visibility.
Robust linkages
The front and rear linkages with weight compensation
ensure optimal work in grassland and mountainous terrain.
The hydraulic weight compensation in the front linkage has
a long accumulation period and therefore lifts at once.
The standard front linkage cat. I lifts 900 kg and can be
equipped with a hydraulic top link. The rear 3 point linkage
with moving lower links has a lifting power of 950 kg.
G3
G3
REFORM Metrac G models
Mechanical speed
change gearbox
Shifting made easy – the Metrac G3 – G7 X series comes
with standard synchronised shuttle gearbox to provide exact and safe
shifting in any situation. The close gear stepping enables optimum usage
of the high engine output and provides the right driving speed for any type
of work. The speed change gearbox has four speeds, which the two or
three range change gearbox translates to 8 or 12 gears, respectively.
1 clutch
2 mech. transfer gear
The gear levers are ergonomically and
clearly placed.
3 4 speed speed change gearbox
4 range change gearbox (2 or 3 ranges)
2
4 speeds
2 ranges
8F / 8R
3 ranges
12F / 12R
(option)
The mechanic drive goes from the diesel
engine via a single disc dry clutch to the
mechanical transfer gear and from there
via a cardan shaft to the 4 speed change
gearbox. This is translated to 8 or 12 speeds,
respectively, by the 2 or 3 range range
change gearbox.
1
4
3
Gear I
Gear II
Gear III
Gear IV
G3
G4 X
G5 X
G6 X
G7 X
26x12.00-12
31x15.5-15
33x15.5-15
——
1.0
1.5
——
1.9
2.6
——
3.0
4.1
——
4.1
5.7
Gear I
2.0
2.2
3.1
Gear II
3.3
4.0
5.6
Gear III
5.5
6.3
8.8
Gear IV
9.2
8.8
12.3
Gear I
4.3
6.9
9.6
Gear II
7.3
12.3
17.2
Gear III
12.1
19.5
27.2
Gear IV
20.1
27.3
38.0
Speeds in kph
with standard
tyres
The benefits at a glance:
•
•
•
•
•
•
Synchronised shuttle gearbox
Closely and evenly stepped gears
Short, direct shifting travels
Low starting speeds especially in the road driving range
All speeds are switched in both directions of travel
2 gearbox variants:
8F / 8R speeds for agricultural use, 12F / 12R speeds (incl. 4 creep speeds)
for working in the slow speed range, e.g., snow blower
Metrac 4 X and 5 X
Metrac 4 X and 5 X
Metrac 6 X and 7 X
Metrac 6 X and 7 X
REFORM Metrac H-models
Hydrostatic
drive.
The hydrostatic drive with 4 speed ranges enables the
stepless adjustment of the drive speed to the various working
conditions and provides additional safety on slopes through
permanent transmission of power.
The special driving comfort
Speed adjustment and change of driving
direction with one control lever.
Choose your driving mode:
Manual with the multi function control lever
Continuous F/R control with notch in the neutral position, for efficient
use with swather or rotary tedder, in partial load operation with low
engine speed.
Automotive via accelerator pedal
For the use with rotary disc mower or flail mower, when high PTO
speed for clean cut and high power is needed.
2 mech.
ranges
2 hydraulic
ranges
automotive or
manual
The hydrostatic drive goes from the diesel
engine to the variable pump, which forms a
hydraulic circuit with the variable motor, and
from there mechanically to the downstream
2 range range change gearbox to the
wheels.
1
2
3
1 variable pump
2 variable motor
3 2 range range change gearbox
Speeds in kph with standard tyres
31x15.5-15
1st range 0 – 7
H4 X
H5 X
2nd range
1st range
0 – 18.1
0 – 36.0
2nd range
1st range
H6 X
H7 X
0 – 13.9
2nd range
1st range
2md range
33x15.5-15
0 – 7.6
0 – 14.6
0 – 19.7
0 – 38.0
The benefits at a glance:
•
•
•
•
•
•
•
•
4 speed ranges for maximum power transmission
Easy and safe manoeuvring in difficult terrain
Soft, smooth starting for special protection of the turf
Continuous speed selection for forward and reverse driving
Maximum safety on slopes through permanent transmission of power
Manual or automotive drive mode depending on application
High working comfort for driver and protection for the brakes
Inch pedal as active safety device for fast stopping
REFORM Metrac G4 X – H5 X
The versatile
multi-talents for any job.
With its Metrac 4X and 5X models, REFORM has devised a high performing,
comfortable and reliable line for applications in mountain agriculture, landscaping,
and in many other areas. With this, the most diverse jobs can be handled, safely and
precisely, in smallest spaces or in the most extreme terrain. Benefit from the Metrac mid
range through high quality, smart technology, superior function, and efficiency.
The flexible and extremely efficient
4 cylinder engines utilize the maximum
torque over a wide speed range and benefit
from enormous engine output. The high
torque ensures full power and flexibility in
partial load operation. The quadruple rubber
mounting of engine and cab keeps vibrations
out of the cabin.
Everything under control with the multi-function control lever!
In the H models, you select the right drive speed and direction with the multi function
control lever, irrespective of the engine speed and under load. In the G models, you use
the multi function control lever to switch between forward and reverse gear. The buttons
on the multi function control lever provide unparalleled comfort for operating the most
frequently used hydraulic functions:
Front linkage
lifting / lowering
Activating the weight
transfer
Hydr. lateral displacement
Front linkage
4 wheel steering
on/off
Hydr. top link or other
functions
forward / backward
Drive speed (H
models only)
Height adjustable headlights
The toolless height adjustable headlights
can be easily adapted to the attachments
and the working conditions. Guards protect
against damage.
The easily accessible filler neck provides for
fast filling stops, and the electrical external
control for the linkage makes mounting and
removing of attachments easy.
The clearly organised cockpit, with clearly separated indicator
and warning lights, provides essential information permanently. You
can fully focus on your work. All controls are ergonomically positioned
and clearly arranged in functional groups in the driver's area of vision
– so you have everything under control at all times. The wide door
opening and the generous space make the Metrac a comfortable
workplace. The cab is vibration damped via the cab mountings and
can be upgraded to comfort cab with heating and air-conditioning.
REFORM Metrac G4 X – H5 X
The mid-range at a glance:
•
•
•
•
•
•
•
•
•
Speed change gearbox or hydrostatic travel drive
- Narrowly stepped shuttle gearbox with 8 or 12 F/R gears
- Hydrostatic drive for continuous control of the drive speed with only one lever.
Front linkage with side shift (G4 X, H4 X optional)
Low slung and lightweight design for best slope capability
Top comfort cab – optionally with air conditioning.
Electro hydraulic weight compensation.
4 wheel steering, switchable to front, rear, and
crab steering, ensures highest agility and soil protection.
Hydrostatic steering with 4 steering modes as standard
equipment.
4 cylinder naturally aspirated engine
G4 X, H4 X
4 cylinder naturally turbo charged
engine
G5 X, H4 X
All control elements are grouped ergonomically and clearly
according to function and are within the driver's reach – so you
have everything under control and can fully focus on your work.
From the hydraulic control panel you control the rear linkage
or other hydraulic attachment features conveniently and with
the push of a button. Switching a control device to oil motor
operation with the push of a button. With the toggle feature
between front and rear linkage, you operate the rear linkage
including weight compensation conveniently with the multifunction lever. In the hydrostat models, you select the the driving
mode (automotive or manual) as well as the speed ranges 1 or 2
in a clearly laid out way at the hydraulic control panel.
The exterior electric control for the front
linkage is standard and makes mounting of
attachments much easier.
The Metrac G4 X and H4 X models have a
fixed front linkage as standard equipment,
they are optionally available with
hydraulic side shift.
Powerful operation hydraulics with comfort operation
The hydraulics block with electromagnetic operation is the basis
for fulfilling the various requirements for attachment operation
both in the front and the rear. The control valves are conveniently
operated from the multi-function control lever or the control panel
to the right of the driver.
The hydraulic couplings are easily accessible and marked both
with colours and symbols, which makes mounting of attachments
so much easier.
REFORM Metrac G6 X – H7 X
Top performance with the
powerful and comfortable
top range.
With its Metrac 6X and 7X series, REFORM offers compact design, productivity and
efficiency in cultivation of slope terrain in a new dimension. Pleasing optics, comfortable
operation and modern technology elevate these models to the top range. Working
with a Metrac 6X or 7X is a special treat. Enormous slope capability and soil
protection, tried and tested 4 wheel drive, high driving comfort and convincing
performance – these benefits are hard to describe in words, they should be
"experienced" hands on.
Adjustable vents in the roof area, vents to
the windscreen and in the footwell allow the
driver to create his or her individual "working
climate".
Take your seat and look forward to your work.
You can work for hours without getting tired with the
longitudinally and height adjustable comfort seats with
adjustable backrest in different versions:
1 Easy care with leatherette cover
2 Pleasant with cloth cover
3 Comfortable with air damping
Optional: high backrest, arm rests, cloth seat cover,
seat belt, or side swivel unit.
Exceptional driving
comfort with the electric
WIPOMAT swivel unit.
(option).
A stereo radio with CD or MC will make your workday even
more enjoyable (option). The roof area also accommodates
the controls for the air conditioning and ventilation system,
switches for auxiliary lights, the cab illumination, as well as rear
view mirror and sun visor.
"Driving a Metrac" is sheer pleasure with
the clearly structured and straightforward
arrangement of controls.
The clearly organised cockpit, with clearly separated indicator
lights and gauges, provides you permanently with essential
information. You can fully focus on your work.
Digital displays: Operating hours meter, daily hours counter, clock,
PTO speed front and rear, straight wheel alignment, misc. warning
indicators, temperature display for hydrostat. drive in H models.
Analogue displays: Fuel gauge, tachometer, speedometer, coolant
temperature display.
Indicator lights for, e.g., differential locks, 4 wheel drive, hand
brake, current steering mode.
REFORM Metrac G6 X – H7 X
The top range at a glance:
•
•
•
•
•
•
•
•
•
•
•
Superior slope capability and terrain mobility
Speed change gear or hydrostatic drive
- Comfortably to operate fully synchronised speed change and reverse gears
- Hydrostatic drive with 4 speed ranges and switchable automotive control
for maximum power transmission
Power shift PTO front and rear
Dual circuit 4 wheel brake for safety in every situation
New deluxe cab for comfortable working
Engine power from 4 cylinders thanks to large displacement
High axle loads and powerful front and rear linkages for high-performance attachments
Wide track and large Terra tyres for extreme slope capability
Electro-hydraulic weight compensation
4 steering modes as standard equipment in the chassis concept
Pre selectable differential locks
The modern 4 cylinder turbo-charged
diesel engines with 62 or 70 hp are
distinguished by low fuel consumption,
very smooth running, good torque and long
service life. The high torque, available from
low revs and across a wide range, delivers
good engine output with power to spare in
any situation.
Additional functions
e.g. hydr. side shift
and hydr. top link
Front linkage
control
Rear linkage
control
4 wheel steering
on/off
Forward backward;
drive speed
(H models only)
Multi functional operation with one hand!
In the Metrac top range, you control the essential hydraulic functions and the driving
direction with the push of a button via the multi-function control lever.
On the side control panel you find, clearly
arranged and colour coded, further hydraulic
functions such as linkage deactivation,
weight compensation toggle or oil motor
operation (depending on the desired
hydraulic system version).
The hydraulic couplings of the high
performance working hydraulics are easily
accessible and colour coded. Combined
with the exterior electric controls of
the linkages, this makes mounting of
attachments almost "a piece of cake".
Take your seat and look forward to your work.
The wide entry ensures comfortable and safe access to the
high spec cab. The clear and functional layout of the controls
provides high driving and operating comfort and ensures that
you don't get distracted during driving and can fully focus on
your work. Conventional analogue gauges combined with a
digital display gives you all information at a glance. The
comfortable seat, the adjustable steering wheel, and ample head
and foot room meet the expectation of any user. Optionally,
the cab can be upgraded to a deluxe cab with heater and air
conditioning, with wide opening, full glass door.
Metrac accessories
Top equipment for any job.
The detachable rotating warning light makes
you visible even in poor weather conditions.
One or two working lights on or below the cab
roof provide best view of the rear working area.
The integrated auxiliary lights at the roof
front ensures maximum visibility, turning night
virtually into day.
Mechanical or automatic trailer hitches are
available for different applications.
The height adjustable trailer hitches with slide
are a special advantage (mechanical, automatic,
or with ball head).
With the hydraulic top link, you can react to
uneven ground quickly from the cab or adjust
the cutting height with the push of a button.
The sound of a stereo radio with CD or
MC will make your workday even more
enjoyable.
Comfortable climate with roof-integrated air
conditioning or additional fresh air supply for
closed cab with the integrated roof ventilation
system.
All Metrac models can be finished in your
specified custom paint.
No load is too heavy for
the Metrac rear linkages.
The robust design of the 3 point rear linkage with weight compensation make the
Metrac a universal working machine. The large lifting forces of 1200 or 1500 kg in the
X series allow the use of high performance attachments.
Exterior
electric controls
• Double acting cylinders (lift/pressure)
(switchable to single acting).
• Movable strut supported lower links
• Longitudinally adjustable lift struts and
lowering speed control.
• Optional vibration damping
(G6X – H7X series)
• Switching from front weight compensation
Retaining balls cat. 1
and 2 or hook ends cat. 2 to the rear linkage (option).
Extra Stability is achieved by
supporting the rear linkage with pull
rods on the rear axle.
REFORM Metrac
The climbers with the strong profile
7X
7X
Basic tyres
7X
G3
–H
G4X
–H
G4X
26x12.00-12 Terra
31x15.50-15 Terra
33x15.50-15 Terra
440/50 R17
All-Ground
29x13.50-15 Terra
31x15.50-15
AG
31x15.50-15
turf
425/55 R17
AG
31x15.50-15
with 6.50-16*
33x15.50-15
with 7.50-16
–H
G6X
The wide low pressure tyres
with various special profiles
ensure maximum traction,
low ground pressure and
reliable turf protection.
They provide grip on difficult
soils and on steep slopes.
Auxiliary tyres
29x13.50-15
with 5.00-16*
*not shown: 26x12.00-12 with 5.00-15
Up the hill
– with even
more grip!
1
3
2
Choose your profile:
1 Narrow tread low pressure tyres for
maximum soul protection
2 Agricultural tyres for high pulling performance and high stability
3 Turf tyres for intensive lawn care
Even better slope capability and soil protection with the
front and/or rear auxiliary tyres. Quick installation and removal with quick
release.
If you want to switch the auxiliary wheels between front and rear axle, you can
install mounting parts on both axles for a quick change between front and rear.
Innovative engineering since 1910
Customer Satisfaction
through Quality.
The Reform-Werke Wels is one of the few manufacturers which assume undivided responsibility for the
entire value added chain. Have a brief tour on the creation of Reform products, from development of a new
machine to standard production. The entire production process is subject to the requirements of the ISO
9001 quality management system.
Latest equipment, such as 3 D CAD, in design
and development of new special purpose
vehicles.
In parts production precision parts are
manufactured on leading edge CNC tools in
different batch sizes.
Permanent quality control ensures compliance
with standards according to the ISO 9001 quality
management system.
In line assembly, excellently trained and
continuously schooled expert personnel produce
a wide range of vehicle types and variants.
Before delivery, all vehicles undergo intensive
functional testing such as here on the roller
test bed.
In the end of line check and the finishing
department, all machines are thoroughly
checked once more and prepared for shipment
to their future owners.
REFORM – on the way to the customer.
A large part of the machines
are transported with
REFORM's own
lorries – they reach their
destination fast and safely.
Our new transport vehicles – in eye-catching,
contemporary design have special accessories
for the optimal loading of REFORM machines.
Additionally, we also use outside forwarding
agencies and railway transport.
Metrac G5 X
Metrac G7 X
Technical Specification
Metrac G3
Engine
4 cylinder 4 stroke diesel engine, Kubota V 2003 M EU-32, stage 3A, 32.1 kW (44 hp) at
2800 rpm, displacement 1999 cm³, water cooled.
Gearbox
Shuttle gearbox with 8 forward and 8 reverse gears,
Speed: 2.0 – 20.1 kph (26" tyres); 2.3 – 23.0 kph (29" tyres)
Clutch
Single disc dry clutch for travel drive and rear PTO (via clutch pedal), multi disc clutch for
front PTO drive (hand lever operated).
Axles
Driving/steering axles front and rear, front axle oscillating.
Axle drive
Four wheel drive, front wheel drive switchable.
Differential locks
Self-locking differential front, manual differential lock rear.
Steering system
Hydrostatic steering with Load Sensing; electro-hydraulic steering switch during driving,
pre-selectable with options for 4 wheel, front, rear, and continuously adjustable crab
steering; automatic synchronisation of wheel position.
Service brake
Hydr. dual circuit 4 wheel power brake.
Parking brake
Mechanical parking brake and steering brake mechanism acting on front wheels.
Engine hydraulics
Hydraulic pump 26.6 l/min, 180 bar, oil tank 8 l, standard equipment Var. B1: 1 control
valve each for front and rear linkage, 1 control valve d.a.f. with parallel lines front and
rear; option: var. C1: 1 additional control valve d.a.f. with parallel lines front and rear
(max. 4 trailer couplings front and 4 rear)
Front linkage
Front 3 point linkage with hydraulic weight compensation, quick release system via
seating locators, top link mount,
lifting force max. 900 kg.
Rear linkage
(option)
Rear 3 point linkage with movable lower links, retaining balls cat. 1 + 2,
single acting cylinders, lowering speed control, lifting force 950 kg. Option: Lower links
with hook ends cat. 2, double acting cylinders (lift/pressure), drawbar.
PTO
Power shift PTO front 540 rpm, counter-clockwise, gearbox PTO rear rear
540 rpm, clockwise; (direction of rotation: looking at PTO shaft end).
Cab
Driver rollover protection frame with roof and tinted windscreen, side window right
and rear window, comfort seat, wiper with windscreen washer, cable lead-through for
attachments.
Gauges
Tachometer with integrated operating hours meter, fuel gauge, temperature gauge,
indicator for straight wheel alignment, various indicator lights with symbols.
Electric system
Battery 12 V, 60 Ah, alternator40 A full road lighting, complete, Option: Auxiliary lights
front on roof, 1 working light rear, rotating warning light.
Fuel tank
Polyethylene tank, capacity 35 l.
Seat designs
Comfort seat with leatherette cover, pelvic support, longitudinally and height adjustable,
tilt adjustable backrest; Option: High backrest, protective cloth cover,
arm rest, seat belt.
Accessories
Mechanical or automatic trailer hitches (mountable at various heights),
hydraulic front top link, top link elevation; further options on request.
Attachments
Twin blade mower, rotary disc mower, side delivery belt rake, front collecting fork,
dump bucket, snow plough, further attachments on request.
Weights
Dead weight: 1400 kg with 26" tyres, 1440 kg with 29" tyres
Perm. axle load front: 1350 kg, perm. axle load rear: 1420 kg
Perm. gross weight: 2200 kg
Turning radius
3.10 m (with 4 wheel steering)
Metrac G4 X, G5 X
Metrac H4 X, H5 X
4 cylinder 4 stroke diesel engine, G4 X: Kubota V2403-M naturally aspired engine,
36 kW (49 hp) at 2700 rpm; G5 X: Kubota V2403-M-T with turbocharger, 43.3 kW (59
hp) at 2700 rpm; displacement 2434 cm³, water-cooled.
4 cylinder 4 stroke diesel engine, H4 X: Kubota V2403-M naturally aspired engine,
36 kW (49 hp) at 2700 rpm; H5 X: Kubota V2403-M-T with turbocharger, 43.3 kW (59
hp) at 2700 rpm; displacement 2434 cm³, water-cooled.
Shuttle gearbox with 8 forward and 8 reverse gears, synchronised speed change
and reverse gears, 2.3 – 27.3 kph with 31" tyres; 2.4 – 29.5 kph with 33" tyres, Option:
Creep speed variant, 12 forward and 12 reverse gears, 1.04 – 27.3 kph with 31" tyres, 1.12
– 29.5 kph with 33" tyres.
Hydrostatic drive with mechanical 2-range gear and electro-hydraulic 2-level switching,
inching function, hydrostatic control optionally automotive or manual, electrically
switchable. 4 speed ranges: with 31" tyres:
Field: 0 – 7.0 kph / 0 – 13.8 kph, road: 0 – 18.1 kph / 0 – 36.0 kph, with 33" tyres: Field:
0 – 7.6 kph / 0 – 15.0 kph, road: 0 – 19.6 kph / 0 – 39.0 kph
Single disc dry clutch with hydraulic central disengagement for drive,
multi disc clutch for PTO drive (electro-hydr. switchable).
Single disc dry clutch with hydraulic central disengagement for PTO drive
(electro-hydr. switchable).
Driving/steering axles with final drives front and rear, front axle oscillating.
Four wheel drive, front-wheel drive switchable.
Pre-selectable, manually operated differential locks front and rear, with switch status indicator lights on dashboard.
Hydrostatic steering with Load Sensing; electro-hydraulic steering switch during driving, pre-selectable with options for
4 wheel, front, rear, and continuously adjustable crab steering; automatic synchronisation of wheel position.
Hydr. dual circuit 4 wheel power brake.
Mechanical parking brake acting on rear wheels.
Hydraulic pump 29.7 l/min, 195 bar, oil tank 13 l, standard equipment Var. C4: 1 control valve each for front and rear linkage, 2 control valves d.a.f. with parallel lines front and rear,
switchover cock at rear linkage, one tank return line each front and rear, operation by multi-function control lever; Option: var. D4: 1 additional control valve d.a.f. with
parallel lines front and rear (max. 10 trailer couplings front and 8 rear)
Angle swing lift, with electro-hydraulic weight compensation, quick release system using
seating locators, cat. 1, lowering speed control, electric external control, lifting force
1300 kg. Option: Vibration damping, G4 X: fixed design, hydraulic side shift optional.
G5 X: Integrated side shift with 400 mm adjustment range
(+/- 200 mm).
Angle swing lift, with electro-hydraulic weight compensation and vibration damping,
quick release system using seating locators, cat. 1, lowering speed control, electric
external control, lifting force 1300 kg. H4 X: fixed design, hydraulic side shift optional.
H5 X: Integrated side shift with 400 mm adjustment range (+/- 200 mm).
Rear 3 point linkage with movable lower links, retaining balls cat. 1 + 2, double acting cylinders (lift/pressure), switchable to single action, lowering speed control, electric external
control, lifting force 1200 kg. Option: Lower links with hook ends cat. 2, electro-hydraulic weight compensation, drawbar, vibration damping.
Power shift PTO front 540 rpm, counter-clockwise, and rear 540 and 750 rpm,
clockwise; electro-hydraulically switchable with automatic soft start (direction of rotation:
looking at PTO shaft end).
Power shift PTO front and rear 540 rpm, front counter-clockwise, rear clockwise, electrohydraulically switchable with automatic soft start (direction of rotation: looking at PTO
shaft end).
Vibration damped driver rollover protection frame with roof, panoramic windscreen, right side window, tinted window, comfort seats in various versions,
parallelogram wipers, windscreen washer, sun visor, 2 exterior mirrors, interior mirror, bottle holder, radio preparation in the roof (2 speakers and aerial). Option: Closed deluxe cab
with heating, electric cab ventilation, air-conditioning.
Tachometer with integrated operating hours meter, fuel gauge, temperature gauge,
cigarette lighter, indicator lights with symbols for, e.g., differential locks, four wheel drive,
hand brake, steering modes. Option: Digital speed display.
Tachometer with integrated operating hours meter, fuel gauge, temperature gauge,
cigarette lighter, indicator lights with symbols for, e.g., differential locks, four wheel drive,
hand brake, steering modes. Digital display for drive speed, temperature display for
hydrostatic drive.
Battery 12 V, 90 Ah, alternator 70 A, full road lighting, complete with height adjustable headlights; Option: Auxiliary lights front on roof,
1 working light rear, rotating warning light.
Polyethylene tank, capacity 63 l.
Longitudinally and height adjustable comfort seats with pelvic support and tilt adjustable backrest in 3 designs: Comfort seat with leatherette cover (standard) or cloth cover, air
cushioned seat with cloth cover; Option: Side swivel unit, high backrest for comfort seat, protective cloth cover, seat belt, arm rests.
Linkage toggle front/rear, hydraulic vibration damping front and rear, mechanical or
automatic trailer hitches (fixed or height adjustable), var. accessories for cab, 2 speakers
and aerial, stereo radio with CD or MC, hydraulic top link, auxiliary weight compensation
for front linkage, heated fuel filter, reverse buzzer, exhaust tail pipe routed to the rear,
custom paint, snow chains;
Further options on request.
Linkage toggle front/rear, hydraulic vibration damping rear (standard front), mechanical
or automatic trailer hitches (fixed or height adjustable), var. accessories for cab, 2
speakers and aerial, stereo radio with CD or MC, hydraulic top link, auxiliary weight
compensation for front linkage, heated fuel filter, reverse buzzer, exhaust tail pipe routed
to the rear, custom paint, snow chains;
Further options on request.
Twin blade mower, rotary disc mower, side delivery belt rake, front collecting fork, dump bucket, front and/or side twin blade mower, front end loader,
flail mower, extension arm boom flail mower, sickle mower (with side or rear ejection), suction container with or without high discharge, road sweeper, self-loading salt spreader,
snow plough, snow blower; further attachments on request.
Dead weight (with standard equipment): G4 X: 1850 kg, G5 X: 1870 kg
Perm. axle load front: 1800 kg, perm. axle load rear: 1800 kg; perm. gross weight: 3000
kg
Dead weight (with standard equipment): H4 X: 1870 kg, H5 X: 1890 kg
Perm. axle load front: 1800 kg, perm. axle load rear: 1800 kg; perm. gross weight: 3000
kg
3.55 m (with 4 wheel steering)
Metrac G6 X, G7 X
Metrac H6 X, H7 X
4 cylinder 4 stroke diesel engine, VM-D 754 SE 3 with turbocharger, G6 X: 45.6 kW
(62 hp) at 2600 rpm, G7 X: 51.5 kW (70 hp) at 2600 rpm, displacement 2970 cm³,
water-cooled.
4 cylinder 4 stroke diesel engine, VM-D 754 SE 3 with turbocharger, H6 X: 45.6 kW
(62 hp) at 2600 rpm, H7 X: 51.5 kW (70 hp) at 2600 rpm, displacement 2970 cm³,
water-cooled.
Shuttle gearbox with 8 forward and 8 reverse gears, synchronised speed change and
reverse gears, 2.9 – 35 kph with 31" tyres; 3.1 – 38 kph with 33" tyres, 3.3 – 40 kph with
425 tyres. Option: Creep speed variant, 12 forward and 12 reverse gears, 1.3 – 5.3 kph
with 31" tyres, 1.4 – 5.7 kph with 33" tyres, 1.5 – 6.0 kph with 425 tyres.
Hydrostatic drive with mechanical 2-range gear and electro-hydraulic 2-level switching,
inching function, hydrostatic control optionally automotive or manual, electrically
switchable. 4 speed ranges: with 33" tyres: Field: 0 – 7.6 kph / 0 – 14.6 kph, road: 0 – 19.7
kph / 0 – 38.0 kph; with 425 tyres: Field: 0 – 8.0 kph / 0 – 15.4 kph, road: 0 – 20.7 kph /
0 – 40.0 kph
Single disc dry clutch with hydraulic central disengagement for drive,
multi disc clutch for PTO drive (electro-hydr. switchable).
Single disc dry clutch with hydraulic central disengagement for PTO drive
(electro-hydr. switchable).
Driving/steering axles with final drives front and rear, front axle oscillating.
Four wheel drive, front-wheel drive switchable.
Pre-selectable, electro-hydraulically operated differential locks front and rear, with gear status indicator lights on dashboard.
Hydrostatic steering with Load Sensing; electro-hydraulic steering switch during driving, pre-selectable with options for
4 wheel, front, rear, and continuously adjustable crab steering; automatic synchronisation of wheel position.
Hydr. dual circuit 4 wheel simplex brake with brake booster.
Hydr. dual circuit 4 wheel power brake.
Mechanical parking brake acting on rear wheels.
Hydraulic pump 24.2 l/min, 195 bar, oil tank 13 l, standard equipment Var. C4: 1 control valve each for front and rear linkage, 2 control valves d.a.f. with parallel lines front and rear,
switchover cock at rear linkage, one tank return line each front and rear, operation by multi-function control lever; Option: Var. D4: 1 additional control valve d.a.f. with
parallel lines front and rear (max. 10 trailer couplings front and 8 rear)
Angle swing lift with electro-hydraulic weight compensation and vibration damping , quick release system using seating locators, cat. 1, lowering speed control,
electric external control, integrated side shift with 400 mm adjustment range (+/- 200 mm), lifting force 1500 kg.
Rear 3 point linkage with movable lower links, retaining balls cat. 1 + 2, double acting cylinders (lift/pressure), switchable to single action, lowering speed control,
electric external control, vibration damping, lifting force 1500 kg. Option: Lower links with hook ends cat. 2, electro-hydraulic weight compensation, drawbar.
Power shift PTO front 540 rpm, counter-clockwise, and rear 540 and 750 rpm,
clockwise; electro-hydraulically switchable with automatic soft start (direction of rotation:
looking at PTO shaft end).
Power shift PTO front and rear 540 rpm, front counter-clockwise, rear clockwise, electrohydraulically switchable with automatic soft start (direction of rotation: looking at PTO
shaft end).
Vibration damped driver rollover protection frame with roof, panoramic windscreen, right side window, tinted window, comfort seats in various versions,
parallelogram wipers, windscreen washer, sun visor, 2 exterior mirrors, interior mirror, bottle holder, radio preparation in the roof (2 speakers and aerial)
Option: Closed deluxe cab with heating, electric cab ventilation, air-conditioning.
Indicator lights with symbols, e.g., for differential locks, four wheel drive, hand brake,
current steering mode; Analogue displays: Fuel gauge, tachometer, speedometer, coolant
temperature display. Digital displays: Operating hours meter, daily hours counter, clock,
PTO speed front and rear, straight wheel alignment, various warning indicators, cigarette
lighter.
Indicator lights with symbols, e.g., for differential locks, four wheel drive, hand brake,
current steering mode; Analogue displays: Fuel gauge, tachometer, speedometer, coolant
temperature display. Digital displays: Operating hours meter, daily hours counter, clock,
PTO speed front and rear, straight wheel alignment, various warning indicators, cigarette
lighter, temperature display for hydrostat. drive.
Battery 12 V, 90 Ah, alternator 110 A, full road lighting, complete with height-adjustable headlights; Option: Auxiliary lights front on roof,
1 or 2 working light(s) rear, rotating warning light.
Polyethylene tank, capacity 85 l.
Longitudinally and height adjustable comfort seats with pelvic support and tilt adjustable backrest in 3 designs: Comfort seat with leatherette cover (standard) or cloth cover, air
cushioned
seat with cloth cover; Option: Side swivel unit, high backrest for comfort seat, protective cloth cover, seat belt, arm rests.
Weight compensation front/rear switchover, mechanical or automatic trailer hitches (fixed or height adjustable), various accessories for cab,
stereo radio with CD or MC, hydraulic top link, auxiliary weight compensation for front linkage, heated fuel filter, reverse buzzer, exhaust tail pipe routed to the rear,
custom paint, snow chains; further options on request.
Twin blade mower, rotary disc mower, side delivery belt rake, front collecting fork, dump bucket, front and/or side twin blade mower, front end loader,
flail mower, extension arm boom flail mower, sickle mower (with side or rear ejection), suction container with or without high discharge, road sweeper, self-loading salt spreader,
snow plough, snow blower; further attachments on request.
Dead weight (with standard equipment): G6 X: 2200 kg, G7 X: 2210 kg
Perm. axle load front: 2100 kg, perm. axle load rear: 2100 kg; perm. gross weight: 3400
kg
Dead weight (with standard equipment): H6 X:2200 kg, H7 X: 2210 kg
Perm. axle load front: 2100 kg, perm. axle load rear: 2100 kg; perm. gross weight: 3400
kg
3.55 m (with 4 wheel steering)
Dimensions G3 – H7X
B C
A
B
C
D
E
F
G
Wheel outer widths G3 – H7X
Wheelbase
Height incl. roof
Height with rotating warning light
Width
Track front and rear
Length without rear linkage
Length with rear linkage
A
Single tyres
Single tyres
Auxiliary tyres
E
D
G3
G4X
G5X
G6X
G7X
H4X
H5X
H6X
H7X
26x12.00-12
Terra tyres
1885
------
------
------
------
F
26x12.00-12 with 5.00-15
2205
------
------
------
------
G
29x13.50-15
Terra tyres
1985
------
------
------
------
29x13.50-15 with 5.00-16
2300
------
------
------
------
31x15.50-15
Terra tyres
------
2020
------
2020
------
Wheel outer width (mm)
Dimensions in mm with standard tyres
Metrac
G3
Metrac
G4X, G5X
Metrac
G6X, G7X
Metrac
H4X, H5X
Metrac
H6X, H7X
31x15.50-15
turf tyres
------
2020
2020
2020
2020
26x12.00-12
31x15.50-15
33x15.50-15
31x15.50-15
33x15.50-15
31x15.50-15
AG tyres
------
2020
2020
2020
2020
A
1665
1950
1995
1950
1995
33x15.50-15
Terra tyres
------
2020
2020
2020
2020
B
1885
2080
2165
2080
2165
31x15.50-15 with 6.50-16
------
2380
2410
2380
2410
C
2185
2300
2365
2300
2365
33x15.50-15 with 7.50-16
------
2430
2440
2430
2440
D
1885
2000
2020
2000
2020
E
1565
1630
1630
1630
1630
425/55 R17
All-Ground
------
------
2160
------
2160
F
2615
3065
3160
3065
3160
425/55 R17
AG tyres
------
------
2160
------
2160
G
2975
3520
3580
3520
3580
440/50 R17
All-Ground
------
------
2160
------
2160
Reform Metrac – simply the best!
MOWERS
MULI
you experience best possible safety on extreme terrain.
REFORM machines are distinguished by compact
design, low dead weight and excellent soil protection.
The tried and tested REFORM 4 wheel steering allows
formidable agility with the smallest footprint. REFORM
is your partner for all year round operation, offering
solutions tailored to your requirements.
MOUNTY
SEMO/TERRA
Your Reform partner
Bauer & Co Gesellschaft m.b.H.
Haidestrasse 40, A-4600 Wels
FN 139380 x, Landesgericht Wels
Tel. +43 7242 232 0
Fax +43 7242 232 4
www.reform.at
E-mail: info@reform.at
www.reform.at
Postfach 142
Bösch 1
CH-6331 Hünenberg
Tel. +41 41 784 2020
Fax +41 41 784 2022
www.agromont.ch
E-mail: info@agromont.ch
Illustrations may show special equipment. Typographical errors and technological changes excepted.
The acknowledged expert in municipal technology,
intensive lawn care, mountain agriculture,
horticulture and landscaping as well as seed
drill construction since 1910. Innovative quality
solutions help to preserve a livable environment. We
maintain a long term reliable partnership with our
customers. REFORM is your expert for steep slopes so
FR 72633/1011
REFORM –
your strong partner.