Panorama® P33CE Zero Clearance Direct Vent

Panorama® P33CE Zero Clearance
Direct Vent Gas Fireplace
Owners &
Installation Manual
MODEL: P33CE-NG10 Natural Gas
P33CE-LP10 Propane
Panorama P33CE
www.regency-fire.com
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach you gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
919-364
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
09.15.15
2
| To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Gas Fireplace by FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. The
P33CE has been designed to provide you with all the warmth and charm of a wood fireplace at the flick of a switch.
The P33CE has been approved by Warnock Hersey/Intertek for both safety and efficiency. As it also bears our own
mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please
take a moment now to acquaint yourself with these instructions and the many features of your Regency® Fireplace.
2| P33CE-10 Direct Vent Gas Fireplace
| 3
INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
This Regency® product has been tested and listed by Warnock Hersey/Intertek as a Direct Vent Wall Furnace to the following standards:
VENTED GAS FIREPLACE HEATERS ANSI Z21.88-2014 • CSA 2.33-2014 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES
CAN/CGA-2.17-M91.
This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.
This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes
follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
Ensure that structural members are not cut or weakened during installation.
This Regency® Mobile/Manufactured Home
Listed appliance comes factory equipped with
a means to secure the unit.
This Regency® Mobile/Manufactured Home
listed appliance comes equipped with a dedicated #8 ground lug to which an 18 gauge copper wire from the steel chassis ground must
be attached.
This appliance may be installed in an aftermarket
permanently located, manufactured (mobile)
home, where not prohibited by local codes.
This appliance is only use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certified kit is used.
Panorama P33CE
P33CE-10 Direct Vent Gas Fireplace |
3
4
| safety decal
Safety Label................................................................. 5
Important Message ..................................................... 7
Before You Start........................................................... 7
General Safety Information.......................................... 7
Installation Checklist..................................................... 8
Locating YOUR FIREPLACE........................................ 8
Duct System Option..................................................... 8
Unit Dimensions........................................................... 9
4 sided faceplate Dimensions...................................... 9
Clearances................................................................. 10
Combustible Mantels...................................................11
Mantel Leg Clearances ............................................. 12
Framing Dimensions.................................................. 13
Framing & Finishing................................................... 14
Venting Introduction.................................................... 16
Exterior Vent Termination Locations........................... 17
Regency® Direct Vent flex System ............................. 18
Installation Procedures............................................... 19
Rigid Pipe Venting Systems....................................... 20
4” x 6-5/8” Rigid Pipe Cross Reference Chart............ 21
Rigid Pipe Venting Arrangements .............................. 23
Vertical Termination with Co-Linear Flex System....... 29
Venting Arrangements - Vertical Terminations ........... 30
Unit installation with Horizontal termination................ 31
Unit installation with Vertical Termination................... 32
Gas Line Installation................................................... 32
Pilot Adjustment.......................................................... 33
High Elevation............................................................ 33
4| P33CE-10 Direct Vent Gas Fireplace
885 S.I.T. Valve Description........................................ 33
Gas Pipe Pressure Testing......................................... 33
Conversion from NG to LP......................................... 34
Optional Brick Panels............................................. ....35
Log Set Installation..................................................... 35
Glass Door and Mesh barrier installation................... 37
Standard Flush Door.................................................. 37
Mesh barrier............................................................... 37
Optional 4-sided faceplate installation........................ 38
Wiring Diagram........................................................... 39
Optional Wall Thermostat Installation ........................ 40
Installing the Optional Fan ......................................... 41
Wiring diagram with optional fan................................ 44
Operating Instructions................................................ 45
First Fire..................................................................... 45
Aeration Adjustment................................................... 45
Lighting Procedure..................................................... 46
Shutdown Procedure.................................................. 46
Copy of the Lighting Plate Instructions....................... 47
Normal Operating Sounds of Gas Appliances............ 48
Maintenance Instructions........................................... 48
General Vent Maintenance......................................... 48
Log Replacement....................................................... 48
Glass Gasket.............................................................. 49
Door Glass................................................................. 49
Removing Valve.......................................................... 50
Installing Valve.............................................................50
Main Assembly............................................................51
Burner & Log Assembly...............................................52
Warranty......................................................................55
safety decal
| 5
SAFETY LABEL
This is a copy of the label that accompanies
each P33CE Zero Clearance Direct Vent Gas
Fireplace. We have printed a copy of the contents
here for your review. The safety label is located
on the front inside base of the unit, visible when
the bottom louver is open.
NOTE: Regency® units are constantly being
improved. Check the label on the unit and if
there is a difference, the label on the unit is the
correct one.
29
29
For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of Massachusetts.
Part #: 919-365
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
Colour: Black on silver, except for items indicated red.
Size: 9.25”For
W xthe
5.73”
H (file
at 100%)
State
of Massachusetts,
the appliances individual manual shut-off must be a t-handle type valve.
Material: 2 ml silver matt polyester (DPM SMS)
May 28/14: The
Created
draft
State
of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO
alarm number
with battery
backfrom
up in
the same
where
*Printer: Continue
sequence
919-122a
- doroom
not restart
at the
0 gas appliance is installed.
P33CE-10 Direct Vent Gas Fireplace |
5
6
| requirements
MA Code - CO Detector
(for the State of Massachusetts only)
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
6| P33CE-10 Direct Vent Gas Fireplace
| 7
installation IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The P33CE-NG10 or P33CE-LP10 Direct Vent
Fireplace must be installed in accordance with
these instructions. Carefully read all the instructions
in this manual first. Consult the "authority having
jurisdiction" to determine the need for a permit prior
to starting the installation. It is the responsibility of
the installer to ensure this fireplace is installed in
compliance with manufacturer's instructions and all
applicable codes.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following:
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVETHAT
CONTROL COMPARTMENTS, BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLIANCE. TODDLERS, YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMENDED IF THERE ARE AT RISK INDIVIDUAL
IN THE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
A BARRIER DESIGNED TO REDUCE
THE RISK OF BURNS FROM THE HOT
VIEWING GLASS IS PROVIDED WITH
THIS APPLIANCE AND SHALL BE
INSTALLED FOR THE PROTECTION
OF CHILDREN AND OTHER AT-RISK
INDIVIDUALS
IF THE BARRIER BECOMES DAMAGED,
THE BARRIER SHALL BE REPLACED
WITH THE MANUFACTURER'S BARRIER
FOR THIS APPLIANCE.
ANY SAFETY SCREEN, GUARD, OR
BARRIER REMOVED FOR SERVICING
AN APPLIANCE MUST BE REPLACED
PRIORTO OPERATINGTHE APPLIANCE.
GENERAL SAFETY
INFORMATION
1) The appliance installation must conform with
local codes or, in the absence of local codes,
with the current Canadian or National Gas
Codes, CAN1-B149 or ANSI Z223.1 Installation Codes.
2) The appliance when installed, must be electrically grounded in accordance with local codes,
or in the absence of local codes with the current
National Electrical Code, ANSI/NFPA 70 or CSA
C22.1 Canadian Electrical Code.
3) See general construction and assembly instructions. The appliance and vent should be
enclosed.
4) This appliance must be connected to the specified vent and termination cap to the outside of
the building envelope. Never vent to another
room or inside a building. Make sure that the
vent is fitted as per Venting instructions.
5) Inspect the venting system annually for blockage and any signs of deterioration.
6) Venting terminals shall not be recessed into a wall
or siding.
7) Any safety glass removed for servicing must
be replaced prior to operating the appliance.
8) To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
9) Wear gloves and safety glasses for protection
while doing required maintenance.
10)Be aware of electrical wiring locations in walls
and ceilings when cutting holes for termination.
11)Under no circumstances should this appliance
be modified. Parts that have to be removed for
servicing should be replaced prior to operating
this appliance.
12)Installation and any repairs to this appliance
should be done by a qualified service person.
A professional service person should be called
to inspect this appliance annually. Make it a
practice to have all of your gas appliances
checked annually.
13)Do not slam shut or strike the glass door.
14)Under no circumstances should any solid fuels
(wood, paper, cardboard, coal, etc.) be used in
this appliance.
15)The appliance area must be kept clear and
free of combustible materials, (gases and other
flammable vapours and liquids).
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm.
P33CE-10 Direct Vent Gas Fireplace |
7
8
| installation
INSTALLATION
CHECKLIST
1) Locate appliance
a) Room location
(Refer to "Locating Your Fireplace" Section)
b) Clearances to Combustibles
(Refer to "Clearances" Section)
c) Mantle Clearances
(Refer to "Combustible Mantels" Section)
d) Framing & Finishing Requirements (Refer
to "Framing & Finishing" Section)
e) Venting Requirements
(Refer to "Venting" Sections)
2) Assemble Top Facing Support and Side
Nailing Strips (Refer to "Unit Assembly Prior
to Installation" Section). NOTE: Must be done
before installing unit into fireplace.
3) Install vent (Refer to "Venting" Sections)
4) Make gas and electrical connections. Test the
pilot. Must be as per diagram.
(Refer to "Gas Line Installation" and "Pilot
Adjustment" Section).
Convert to Propane if desired.
(Refer to "Conversion Kit from NG to LPG"
Section).
5) Install 4-AA batteries into the battery pack or
optional AC power adaptor.
6) Install standard and optional features. Refer to
the following sections:
a. Optional Brick Panels
b. Log Set Installation
c. Standard Flush Door
d. Optional Remote Control
e. Installing the Optional Fan
7) Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained to
customer.
This includes:
1) Clocking the appliance to ensure the correct
firing rate (rate noted on label) after burning
appliance for 15 minutes.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
8| P33CE-10 Direct Vent Gas Fireplace
CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
A)
B)
C)
D)
Flat on Wall
Flat on Wall Corner
Recessed into Wall/Alcove
Corner
LOCATING YOUR
FIREPLACE
1) When selecting a location for your fireplace,
ensure that the clearances outlined on this
page are met.
2) Provide adequate clearances for servicing.
3) The appliance must be installed on a flat,
solid, continuous surface (e.g. wood, metal,
concrete). This may be the floor, or raised up
on a platform to enhance its visual impact.
If the appliance is going to be installed on
carpeting, combustible linoleum tile or other
combustible material other than wood flooring,
the appliance must be installed on a metal or
wood panel extending the full width and depth
of the appliance.
Diagram 1
4) The P33CE can be installed in a recessed
position or framed out into the room as in A,
B, C, D. See Diagram 1 below.
5) This appliance is Listed for bedroom
installations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
DUCT SYSTEM OPTION
6) The P33CE Direct Vent Gas Fireplace is
approved for alcove installations, which meet
the clearances listed on the "Clearances"
Section.
The HeatWave Air Duct Kit increases the
effectiveness of your fireplace by dispersing warm
air from the fireplace to remote locations in the same
room or other rooms in your home.
7) We recommend that you plan your installation
on paper using exact measurements for
clearances and floor protection before actually
installing this appliance. Have a qualified
inspector, dealer, or installer review your plans
before installation.
Up to two kits may be installed on the fireplace.
Please Note: Only 1 HeatWave kit may be operated at one time. This includes the internal blower
option as well.
Note: For vent terminations see "Exterior Vent
Termination Locations" Section.
Kit #946-556
| 9
installation UNIT DIMENSIONS
16"
407mm
23"
584mm
26-1/16"
(662mm)
29-1/4"
742mm
29-1/4"
742mm
2-1/2"
[64mm]
NAILING STRIP
21-3/8"
543mm
16"
(406mm)
34-9/16"
[878mm]
3"
76mm
26"
660mm
29-7/16"
747mm
4 SIDED FACEPLATE DIMENSIONS
6-3/8"
(162mm)
36-3/4"
(933mm)
42-5/16"
(1074mm)
2"
(51mm)
P33CE-10 Direct Vent Gas Fireplace |
9
10
| installation
CLEARANCES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest
importance that this fireplace and vent system be installed only in accordance with these instructions.
Caution Requirements
The top, back and sides of the fireplace are defined by
standoffs. The metal ends of the standoff may NOT
be recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not
adhered to. It is of greatest importance that this fireplace and vent
system be installed only in accordance with these instructions.
C
C
F
G
Close to Ceiling
Clearance:
Dimension
A: *Front Floor Clearance (min.)
0"
Measured From:
Underside of Unit
B: *Sidewall (on one side)
9" (229mm)
Side Opening of Unit
C: *Ceiling
(room and/or alcove)
30" (762mm)
Top Opening of Unit
D: Alcove Width
84" (1219mm)
Sidewall to Sidewall (Minimum)
E: Alcove Depth
36" (914mm)
Front to Back Wall (Maximum)
F: Mantel
12" (305mm)
G:Mantel Clearances
15-3/4" (400mm)
Flue Clearances
Horizontal - Top
Horiztonal - Side
Horiztonal - Bottom
Vertical (Flex Vent)
Vertical (Rigid)
2-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/4"
From Top Opening of Unit
Warning
Fire hazard is an extreme risk if these
clearances are not adhered to.
10| P33CE-10 Direct Vent Gas Fireplace
| 11
installation COMBUSTIBLE MANTELS
Because of the extreme heat this fireplace emits, the mantel clearances are critical. Combustible mantel clearances from top of unit are shown in the
diagram below.
Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board.
This drawing is to scale at 1:6 (one inch = 6 inches). Mantel can be installed anywhere in shaded area or higher using the above scale.
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.
Combustible mantel leg clearances as per diagrams below:
16
10
8
6
2
12" (305mm)
Drywall
7-1/2"(191mm)
14
0 - 3-1/2" (89mm)
12
10
4
0
Mantel Clearances
12
15-3/4" (400mm)
8
6
13-3/4"(349mm)
4
11-3/4"(298mm)
2
Non-combustible material
3"(76mm)
Standoff
0
24-1/4"(616mm)
to floor
Top opening
of Unit
Side View
P33CE-10 Direct Vent Gas Fireplace |
11
12
| installation
MANTEL LEG CLEARANCES
Combustible mantel leg clearances from side of unit as per diagram:
Top View
0-3
Side opening of Unit
6-3/4"
Allowable mantel leg projection
9"
12| P33CE-10 Direct Vent Gas Fireplace
| 13
installation FRAMING DIMENSIONS
M
Non-combustible
Header
(steel stud
on edge)
2X4 HEADER
DETAIL N
SCALE 1 : 6
H
N
I
G
J
N
J
NOTE: If this is an outside corner, the
minimum distance between the vent
and the outside corner is 6" (15cm)
with AstroCap termination cap or 12"
(30cm) with Rigid Vent termination cap.
(For example Dura-Vent)
Floor
I
K
O
L
P Q
Opening for gas
connection
Framing Dimensions
Description
P33CE
P33CE
With Non-Combustible Board Only
(i.e. Painted Finish)
With Tile, Stone, Brick, Slate,
Modera Mantel, Verona Surround
or other Non-Combustible finish
G
Framing Width
H
Framing Height *
I
Framing Rise from Floor
J
Framing Depth
K
Corner Wall Length
L
Corner Facing Wall Width
M
Framed Chase Ceiling*
36" (914mm) Rigid
32" (812mm) Flex
36" (914mm) Rigid
32" (812mm) Flex
N
Vent Centerline Height*
30" (762mm) Rigid
26" (660mm) Flex
30" (762mm) Rigid
26" (660mm) Flex
O
Gas Connection Height*
Vertical
Horizontal
35"(889mm)
35"(889mm)
31-3/4" (806mm)
31-3/4" (806mm)
0"
(when not using a surround / mantel)
0"
2" min (w/ Modera Mantel)
3-5/16" min (w/ Verona Surround)
23-1/4" (578mm) Vertical Rise
20-1/4" (502mm) Rigid / 16-1/2" (406mm) Flex
22-3/4" (578mm) Vertical Rise
19-3/4" (502mm) Rigid / 16" (406mm) Flex
39-1/4" (988mm)
38-15/16" (988mm)
55-1/2" (1410mm)
54-1/2" (1410mm)
1 1/2" (38mm)
1 1/2" (38mm)
P
Gas Connection Inset*
7-3/16" (183mm)
7-3/16" (183mm)
Q
Gas Connection Width*
3" (76mm)
3" (76mm)
* Measured from base of unit
P33CE-10 Direct Vent Gas Fireplace |
13
14
| installation
FRAMING & FINISHING
1. There are 8 (eight) side nailing strips and one top nailing strip available on the unit. One set of four (4) are for a clean finish (board only, painted) installation,
the other set are for a non-combustible finish (ex. tile, concrete, mantel, surround) as they are set back 1/2" (13mm). The top nailing strip is adjustable
to 1/2" (13mm).
2.
Bend the required four (4) nailing strips to 90º.
3. Attach top nailing strip with one (1) screw (located at the back of the nailing strip). Adjust to required position, flush or back 1/2" and tighten screw.
Adjustable Top
Nailing Strip
Nailing strip for
Clean Finish (set
flush with unit)
Nailing strip for
Tile Finish (set
back 1/2")
Nailing strip for
Tile Finish (set
back 1/2")
Nailing strip for
Clean Finish (set
flush with unit)
1. Frame in the enclosure for the unit with framing material.
Note:When constructing the framed opening, please ensure there is access to install the gas lines when the unit is installed.
2. For exterior walls, insulate the enclosure to the same degree as the rest of the house, apply vapour barrier and drywall, as per local installation codes.
(Do not insulate the fireplace itself.)
WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance problems
including, but not limited to: excessive condensation on glass doors, poor flame package, carbon, blue flames etc. These are not product
related issues.
3. The unit does not have to be completely enclosed in a chase. You must maintain clearances from the vent to combustible materials: See "Clearances"
section. Combustible materials can be laid against the side and back standoffs and the stove base.
4. Tile Finish Option 1: Drywall may be installed onto the unit as shown below to create a surface to apply finishing materials such as tile, slate, etc.
Drywall cannot extend onto the metal surface of the unit.
5. Tile Finish Option 2: If applying a non-combustible finishing material (tile,slate,brick, stone, mantel, surround etc) the material can be installed directly
onto the metal surface of the unit in the area shown below.
TILE - STONE - BRICK - MANTEL - SURROUND FINISH
Combustible
Material
Non-combustible Material (3-1/2" x 34-9/16")
Non-combustible
Finishing Material
(ie. tile)
Supplied with Unit
Nailing Strip -1/2" back from unit face
1-1/2
(38mm)
21-3/8"
[542mm]
Ensure finished
material is
brought to lip
Non-combustible
Finishing Material
(ie. tile)
29-7/16"
747mm
14| P33CE-10 Direct Vent Gas Fireplace
Combustible
Material
| 15
installation 6) If applying a non-combustible facing it may be installed over the metal surface of the firebox of the unit in the area shown below.
NON-COMBUSTIBLE BOARD ONLY (PAINTED FINISH)
WOOD STUD
Combustible
Material
1/2" DRYWALL
DO NOT EXTEND
DRYWALL ONTO METAL
SURFACE OF UNIT.
3-1/2"
[89mm]
NON COMBUSTIBLE BOARD SUPPLIED WITH UNIT
34-9/16"
878mm
Non-combustible Material (3-1/2" x 34-9/16")
Supplied with Unit
Non-combustible
Finishing Material
Nailing Strip -flush with unit
NON-COMBUSTIBLE FACING
FOR CLEAN LOOK
(ie. PAINTED FINISH)
Ensure finished
material is
brought to lip
1-1/2
(38mm)
33-7/16"
[849mm]
1/2" DRYWALL
Non-combustible
Finishing Material
Combustible
Material
Combustible and Non-combustible Facing and Finishing
Materials around unit.
NOTE: T
he 3-1/2" x 34-9/16" non combustible material supplied with this unit can be replaced if trying to achieve a clean finish. A large piece of non combustible material (ie. 4' x 8' x 1/2") can be used to eliminate taped seams on or near unit.
7) Non-combustible material (ie. tile, slate, etc) may be brought up to the edge of the glass door of the unit. Minimum clearances must be adhered to, this
will assure ease of glass door removal and access to the lower panel.
NOTE: N
on-combustible finishing materials may be of any thickness desired.
3-1/2"
NON COMBUSTIBLE BOARD SUPPLIED WITH UNIT
No Combustible
Materials in this Area
[89mm]
No Combustible
Materials in this Area
5-3/16"
[132mm]
J Style trim or metal
corner bead may be
used to finish edges
21-3/8"
[542mm]
33-7/16"
[849mm]
21-3/8"
[542mm]
NO FACING OR
FINISHING MATERIAL
IN THIS AREA
29-7/16"
747mm
2-1/2"
[64mm]
34-9/16"
878mm
Minimum Clearances for Finishing Materials
IMPORTANT FINISHING DETAIL NOTE:
Before placing unit into final position - it is important to know the
total thickness / height of finished hearth (tile, carpet, flooring etc.)
The Verona Surround or the Modera Mantel must be level to or higher
than the finished hearth height.
29-7/16"
747mm
Trim materials
Note:
All non-combustible facing material should butt up cleanly
to the flanges around the firebox opening.
Rough edges may be visible from an angle.
To maintain a clean finished edge - facing material edges
may be finished with a J-style trim or metal cornerbead (both
materials available at your local building or hardware store).
IMPORTANT: Materials used must be NON-COMBUSTIBLE.
P33CE-10 Direct Vent Gas Fireplace |
15
16
| installation
VENTING INTRODUCTION
The P33CE uses the "balanced flue" technology Co-Axial system. The inner liner vents products of combustion to the outside while the outer liner
draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room
air up the chimney.
There are 5 vent systems approved for use with the P33CE: the Regency® Direct Vent Flex System for Horizontal Terminations only and the Simpson
Dura-Vent Pro, Selkirk Direct-Temp, Amerivent Direct Vent, Metal-Fab Sure Seal, Security Secure Vent and ICC Excel Direct for Horizontal and Vertical
Terminations (see following "Venting" Sections for more details).
Note: These flue pipes must not be connected to any other appliance.
The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid
fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited. (See "Rigid
Pipe Venting System" for more details and exceptions).
NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.
16| P33CE-10 Direct Vent Gas Fireplace
| 17
installation EXTERIOR VENT TERMINATION LOCATIONS
Minimum Clearance Requirements
Canada1
USA2
A
Clearance above grade, veranda, porch, deck, or balcony
12"(30cm)
12"(30cm)
B
Clearance to window or door that may be opened
12"(30cm)
9" (23cm)
C
Clearance to permanently closed window
*
*
D
Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)
18"(46cm)
18"(46cm)
E
Clearance to unventilated soffit
15"(38cm)
15"(38cm)
F
Clearance to outside corner: with AstroCap Termination Cap.
6"(15cm)
6"(15cm)
12"(30cm)
12"(30cm)
Clearance to outside corner: with all other approved Termination Caps.
G
Clearance to inside corner: with AstroCap Termination Cap
6"(15cm)
6"(15cm)
Clearance to inside corner: with all other approved Termination Caps.
12"(30cm)
12"(30cm)
H
Clearance to each side of center line extended above meter/regulator assembly
36"(90cm)a
*
J
Clearance to service regulator vent outlet
36"(90cm)
*
K
Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance
12"(30cm)
9" (23cm)
L
Clearance to a mechanical air supply inlet
#3' (91cm) above if within 10' (3m) horizontally.
72"(1.8m)
36"(90cm)b
M
Clearance above paved sidewalk or a paved driveway located on public property
84"(2.1m)┼
*
N
Clearance under veranda, porch, deck, or balcony
12"(30cm)‡
*
1
In accordance with current CSA B149.1, Natural Gas and Propane Installation Code
In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
* Clearance in accordance with local installation codes and the requirements of the gas supplier
a 3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly
b 3 feet (91cm) above - if within 10 feet (3m) horizontally
2
┼
P33CE-10 Direct Vent Gas Fireplace |
17
18
| installation
REGENCY® DIRECT VENT FLEX SYSTEM
Horizontal Terminations Only
This venting system, in combination with the P33CE Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey/
Intertek. The location of the termination cap must conform to the requirements in the "Exterior Vent Terminal Locations" Section .
Regency® Direct Vent Flex Termination Kit (Part # 946-513) includes all the parts needed to install the P33CE with a maximum run of 2 feet. If installing the P33E with a continuous vent length of more than 2 ft (.6m) to a maximum of 10 ft. (3.0m) use Kit # 946-515 (4 ft) or 946-516 (10 ft) or see "Rigid Pipe
Venting Systems" Section for alternate venting arrangements.
1)
2)
3)
4)
5)
6)
7)
8)
9)
6-7/8" dia. flexible liner (2 ft. length)
4" dia. flexible liner (2 ft. length)
spring spacers (3)
thimble (2)
AstroCap termination cap (1)
screws (12)
tube of Mill Pac (1)
plated screws (8)
screws #8 x 1-1/2" drill point,
stainless steel (4)
Wall Thimble (2 pc)
(required in
Canada only)
AstroCap TM
Termination Cap
(Part# 946-523/P)
4" (102mm)
dia. flue pipe
spring
spacer
Notes:
1) Liner sections should be continuous
without any joints or seams.
2) Only Flex pipe purchased from Regency®
may be used for Flex installations.
6-7/8"
(173mm)
dia. Flue pipe
See Figure 1 below for
Alternate Caps.
MINIMUM
MINIMUM
RIGID PIPE CENTER-LINE
FLEX KIT CENTER-LINE
Alternate
Horizontal
Termination
Caps
Figure 1
Note: for P33E-NG4 with contemporary faceplate - unit must be raised by 1".
18| P33CE-10 Direct Vent Gas Fireplace
Wherever necessary due to
external location of cap, the
AstroCap can be replaced with
the FPI Riser Vent Termination
Cap or the Dura-Vent Snorkel
Termination Cap.
| 19
installation INSTALLATION PROCEDURES
for Regency® Direct Vent System (Flex)
1) Locate the unit in the framing, rough in the gas
(preferably on the right side of the unit) and the
electrical (Junction block is on the left side) on
the left. Locate the centerline of the termination
and mark wall accordingly. Cut a 10"(254mm)
hole in the wall (inside dimension).
*If this is an outside corner, the minimum distance between the vent and the outside
corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Dura-Vent termination cap. See "F" in the diagram in "Exterior Vent Termination Locations" Section.
Note: To make the installation more aesthetically
pleasing, we recommend framing out a
square to mount the terminal to.
Note: A 2-1/2" (64mm) horizontal top and
1-1/2" (38mm) horizontal sides & bottom
clearance around the liner must be maintained except that only a 1" (25mm) clearance is needed at the termination end.
We recommend framing a 10"(254mm)
x 10"(254mm) (inside dimensions) hole
to give structural rigidity for mounting
the termination.
Note: If installing termination on a siding
covered wall, furring strips must be
used to ensure that the termination is
not recessed into the siding.
2) Level the fireplace and fasten it to the framing
using nails or screws through the nailing strips.
3) Assemble the vent assembly by applying
Mill Pac to the 4"(100mm) inner collar of the
termination and slipping the 4"(100mm) liner
over it at least 1-3/8" (35mm). Fasten with
the 3 screws (drilling pilot holes will make this
easier). Apply Mill Pac to the 6-7/8"(175mm)
flex pipe and slip it over the 6-7/8" outer collar
of the vent terminal at least 1-3/8"(35mm) and
fasten with the 3 screws.
4) Separate the 2 halves of the wall thimble and
securely fasten the one with the tabs to the
outside wall making sure that the tabs are on
top and bottom. Fasten the other thimble half
to the inside wall. The thimble halves slip inside
each other and can be adjusted for 2 x 4 or 2 x
6 walls. The liners must slip over the collars
a minimum of 1-3/8".
Minimum and Maximum Vent Clearances
5) Slip the assembled liner and termination assembly through the thimble making sure the
termination cap faces up (there are markings
on the cap that show which way is up). This will
position the termination cap with proper down
slope for draining water. Fasten the cap to the
outer wall with the 4 supplied screws.
6) Pull the centre 4"(100mm) liner and outer
6-7/8"(175mm) liner out enough to slip over
the flue collars of the fireplace.
7) Apply Mill Pac over the fireplace inner collar
and slip the 4"(100mm) liner down over it and
attach with 3 supplied screws.
4" (102mm)
dia. flue pipe
with spring spacer
8) Do the same with the 6-7/8"(175mm) liner.
9) Apply a bead of silicone between the thimble
and termination and around the outer edge of
the terminal at the wall in order to keep the
water out.
IMPORTANT: Do not locate termination
hood where excessive snow or ice
buildup may occur. Be sure to check
vent termination area after snow falls,
and clear to prevent accidental blockage
of venting system. When using snow
blowers, make sure snow is not directed
towards vent termination area.
2” x 4” or 2” x 6”
(21mm x 102mm
or 21mm x 152mm)
Termination Cap
Screws
(3 per
connection)
6-7/8"
(175mm)
dia. air intake
Screws
(4 per connection)
Wall Thimble 2 pieces
(10" (254mm) Outer Diameter)
P33CE-10 Direct Vent Gas Fireplace |
19
20
| installation
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
The minimum components required for a basic
horizontal termination are:
1AstroCap Horizontal Termination Cap
145o Elbow
1 Rigid Pipe Adaptor
1 Wall Thimble
1 Length of pipe to suit wall thickness
(see chart)
For siding other than vinyl furring strips may be used,
instead of the vinyl siding standoff, to create a level
surface to mount the vent terminal. The Terminal
must not be recessed into siding.
If a Vinyl Siding Standoff is required (it must be
used with vinyl siding), measure to outside surface
of wall without siding and add 2 inches.
Vertical
Terminal
Storm Collar
Vinyl Siding
Standoff (Optional)
Flashing
Horizontal
Termination Cap
# 946-523/P
Ceiling Firestop
Wall Thimble
Pipe Length
Pipe Length
Horizontal
Termination Cap
#946-523/P
o
90 Elbow
Alternate
Horizontal
Termination
Caps
24" Length
Vinyl Siding
Standoff (Optional)
Wall Thimble
Pipe Length
45o Elbow
Rigid Pipe Adapter
# 510-994
WARNING:
Do not combine venting components from
different venting systems.
However use of the AstroCapTM and FPI Riser
is acceptable with all systems.
19-3/4"
(502mm)
27"
(686mm)
Flat Wall Installation
Max. Wall
Vent Length
Thickness (inches) Required (inches)
7 - 1/4"
6"
10 - 1/4"
9"
13 - 1/4"
12"
12-1/4" - 15-7/8" 11" - 14-5/8" Adj. Pipe
18-1/4" - 25-1/4" 11" - 14-5/8" Adj. Pipe
This product has been evaluated by Intertek
for using a Rigid Pipe Adaptor in conjunction
with Duravent Direct-Vent , Selkirk Direct-Temp,
Ameri Vent Direct venting and Security Secure
Vent systems. Use of these systems with the
Rigid Pipe adaptor is deemed acceptable and
does not affect the Warnok Hersey/Intertek
listing of components.
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent Pro,
American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, Selkirk Direct-Temp. AstroCapTM is a proprietary trademark of FPI Fireplace
Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
20| P33CE-10 Direct Vent Gas Fireplace
| 21
installation 4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART
Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.
4” X 6- 5/8” RIGID PIPE CROSS REFERENCE CHART
Components from different Manufacturers may not be mixed. Not all rigid pipe components are available directly from Regency.
Description
Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Metal-Fab™
Sure Seal
Security
ICC Excel
Secure- Vent®
Direct
Amerivent Direct
6” Pipe Length-Galvanized
46DVA-06
4DT-6
N/A
4D6
SV4L6
TC-4DL6
6” Pipe Length-Black
46DVA-06B
4DT-6B
N/A
4D6B
SV4LB6
TC-4DL6B
7” Pipe Length-Galvanized
N/A
N/A
4D7
N/A
N/A
N/A
7” Pipe Length-Black
N/A
N/A
4D7B
N/A
N/A
N/A
9” Pipe Length-Galvanized
46DVA-09
4DT-9
N/A
N/A
N/A
N/A
9” Pipe Length-Black
46DVA-09B
4DT-9B
N/A
N/A
N/A
N/A
12” Pipe Length-Galvanized
46DVA-12
4DT-12
4D12
4D12
SV4L12
TC-4DL1
12” Pipe Length-Black
46DVA-12B
4DT-12B
4D12B
4D12B
SV4LB12
TC-4DL1B
18” Pipe Length-Galvanized
46DVA-18
4DT-18
4D18
4D18
SV4LA
TC-4DL18
18” Pipe Length-Black
46DVA-18B
4DT-18B
4D18B
4D18B
SV4LA
TC-4DL18B
24” Pipe Length-Galvanized
46DVA-24
4DT-24
4D24
4D24
SV4L24
TC-4DL2
24” Pipe Length-Black
46DVA-24B
4DT-24B
4D24B
4D24B
SV4LB24
TC-4DL2B
36” Pipe Length-Galvanized
46DVA-36
4DT-36
4D36
4D36
SV4L36
TC-4DL3
36” Pipe Length-Black
46DVA-36B
4DT-36B
4D36B
4D36B
SV4LB36
TC-4DL3B
48” Pipe Length-Galvanized
46DVA-48
4DT-48
4D48
4D48
SV4L48
TC-4DL4
48” Pipe Length-Black
46DVA-48B
4DT-48B
4D48B
4D48B
SV4LB48
TC-4DL4B
60” Pipe Length-Galvanized
46DVA-60
4DT-60
N/A
N/A
N/A
N/A
60” Pipe Length-Black
46DVA-60B
4DT-60B
N/A
N/A
N/A
N/A
Adjustable Length 3”-10”-Galvanized
N/A
N/A
N/A
4DAL
N/A
TC-4DLT
Adjustable Length 3”-10”-Black
N/A
N/A
N/A
4DALB
N/A
TC-4DLTB
Adjustable Length 7”-Galvanized
N/A
N/A
4D7A
N/A
N/A
N/A
Adjustable Length 7”-Black
N/A
N/A
4D7AB
N/A
N/A
N/A
Extension Pipe 8-1/2”-Galvanized
46DVA-08A
N/A
N/A
N/A
N/A
N/A
Extension Pipe 8-1/2”-Black
46DVA-08AB
N/A
N/A
N/A
N/A
N/A
Adjustable Length 12”-Galvanized
N/A
N/A
4D12A
N/A
SV4LA12
N/A
Adjustable Length 12”-Black
N/A
N/A
4D12A
N/A
SV4LBA12
N/A
Extension Pipe 16”-Galvanized
46DVA-16A
N/A
N/A
N/A
N/A
N/A
Extension Pipe 16”-Black
46DVA-16AB
N/A
N/A
N/A
N/A
N/A
45º Elbow-Galvanized
46DVA-E45
4DT-EL45
4D45L
N/A
N/A
TE-4DE45
45º Elbow-Black
46DVA-E45B
4DT-EL45B
4DT-EL45B
N/A
N/A
TE-4DE45B
45º Elbow Swivel-Galvanized
See 46DVA-E45
N/A
N/A
4D45L
SV4E45
N/A
45º Elbow Swivel-Black
See 46DVA-E45B
N/A
N/A
4D45LB
SV4EB45
N/A
90º Elbow-Galvanized
46DVA-E90
4DT-EL90S
4DT-EL90S
N/A
N/A
TE-4DE90
90º Elbow-Black
46DVA-E90B
4DT-EL90SB
4DT-EL90SB
N/A
SV4EBR90-1
TE-4DE90B
90º Elbow, Swivel-Galvanized
See 46DVA-E90
N/A
N/A
4D90L
SV4E90-1
N/A
90º Elbow, Swivel-Black
See 46DVA-E90B
N/A
N/A
4D90LB
SV4EB90-1
N/A
90º Starter Elbow, Swivel-Galvanized
N/A
N/A
N/A
4D90A
N/A
N/A
Adaptor*
N/A
N/A
N/A
4D90L
N/A
N/A
Ceiling Support
N/A
4DT-CS
4DFSP
4DSP
SV4SD
TE-4DE45
Cathedral Support Box
46DVA-CS
4DT-CSS
4DRSB
4DRS
SV4CSB
TE-4DE45B
Wall Support/Band
46DVA-WS
4DT-WS/B
4DWS
4DWS
SV4BM
N/A
Offset Support
46DVA-ES (N/A - FPI)
4DT-OS
N/A
N/A
SV4SU
N/A
Wall Thimble-Black
46DVA-WT
4DT-WT
4DWT
4DWT
SV4RSM
TE-4DE90
Wall Thimble Support/Ceiling Support
46DVA-DC
N/A
N/A
N/A
SV4PF
TE-4DE90B
Firestop Spacer
46DVA-FS
4DT-FS
4DFSP
4DFS
SV4BF
N/A
Trim Plate-Black
N/A
4DT-TP
4DFPB
4DCP
SV4LA
N/A
P33CE-10 Direct Vent Gas Fireplace |
21
22
| installation
Description
Selkirk
Simpson
American Metal
Products®
Direct Temp™
Direct Vent Pro®
Metal-Fab™
Sure Seal
Security
ICC Excel
Secure- Vent®
Direct
Amerivent Direct
Attic Insulation Shield 12”
46DVA-IS N/A@ FPI
N/A
4DAIS12
N/A
SV4RSA
N/A
Attic Insulation Shield - Cold Climates 36”
N/A
N/A
4DAIS12
N/A
N/A
TM-4AS
Basic Horizontal Termination Kit (A)
Disc.
4DT-HKA
4DHTK2
4DHTKA
SV-SHK
N/A
Horizontal Termination Kit (B)
46DVA-KHA
4DT-HKB
4DHTK1
4DHTKB
SV-HK
N/A
Vertical Termination Kit
Disc.
4DT-VKC
4DHTK
4DHTK
SV-FK
N/A
High Wind Vertical Cap
46DVA-VCH
N/A
N/A
N/A
N/A
TM-4VT
High Wind Horizontal Cap
46DVA-HC
N/A
N/A
N/A
N/A
TM-4DHT
(Changed Components)
Horizontal Square Termination Cap
See 46DVA-HC
4DT-HHC
4DHC
4DHT
SV4CHC-1
TM-4HT
Vertical Termination Cap
46DVA-VC
4DT-HVC
4DVC
4DVT
SV4CGV-1
TM-4VT
Storm Collar
46DVA-08A
4DT-SC
4DSC
4DSC
SV4FC
TM-SC
Adjustable Flashing 0/12-6/12
46DVA-F6
4DT-ST14
4D12S
4DST14
SV4STC14
TF-4FA
Adjustable Flashing 6/12-12/12
46DVA-FLA
4DT-ST36
4D36S
4DST36
SV4STC36
TF-4FB
Vinyl Siding Standoff
46DVA-VSS
4DT-VS
N/A
4DVS
SV4VS
TM-VSS
Vinyl Siding Shield Plate
N/A
4DT-VSP
N/A
N/A
SV4VS
N/A
Snorkel Termination 14”
46DVA-SNKL
N/A
N/A
N/A
N/A
TM-4ST14
Snorkel Termination 36”
N/A
N/A
N/A
N/A
N/A
TM-4ST36
Restrictor Disk
N/A
N/A
N/A
N/A
N/A
TM-4DS
Extended Vertical Termination Cap
N/A
N/A
N/A
N/A
N/A
N/A
Chimney Conversion Kit A (USA only)
46DVA-KCA
N/A
N/A
N/A
N/A
TM-4CA6
Chimney Conversion Kit B (USA only)
46DVA-KCB
N/A
N/A
N/A
N/A
TM-4CA7
Chimney Conversion Kit C (USA only)
46DVA-KCC
N/A
N/A
N/A
N/A
TM-4CA8
Chimney Conversion Kit Masonry
(USA only)
46DVA-KMC
N/A
N/A
N/A
N/A
N/A
Wall Firestop
46DVA-WFS
N/A
N/A
N/A
N/A
TM-4TR
Colinear Flex Connectors
46DVA-ADF
N/A
N/A
N/A
N/A
N/A
FPI
946-506/P
Vent Guard (Optional) for AstroCap
946-205
Vinyl Siding Shield for Riser Vent Terminal
510-994
Rigid Pipe Adaptor (Must use with all rigid piping)
946-208/P
Vent Guard (Optional) for Riser Vent Terminal
640-530/P
Riser Vent Terminal
946-523/P
AstroCap Horizontal Cap
946-605
Starter Collar Increaser 4” x 6-5/8” to 5” x 8”
946-206
Vinyl Siding Standoff for AstroCap
Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
4” x 6-5/8” Venting
Run (X)
Rise (Y)
For specific instructions on venting components - visit the
manufacturers website listed below.
0” (0mm)
4-7/8” (124mm)
13-7/8” (340mm)
Simpson Direct Vent Pro: www.duravent.com
6” (152mm)
8” (203mm)
16-1/2” (419mm)
Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm)
10-1/8” (257mm)
18-5/8” (473mm)
American Metal Products: www.americanmetalproducts.com
12” (305mm)
12-1/4” (311mm)
20-3/4” (527mm)
Metal-Fab Sure Seal: www.mtlfab.com
24” (610mm)
20-5/8” (524mm)
29-1/8” (740mm)
Security Secure Vent: www.securitychimneys.com
36” (914mm)
29” (737mm)
37-1/2” (953mm)
Industrial Chimney Company: www.icc-rsf.com
48” (1219mm)
37-7/16” (951mm)
45-15/16” (1167mm)
Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high temperatures and may present a possible fire hazard.
Regency Fireplace Products . 6988 Venture St. . Delta, BC . Canada . V4G 1H4 . 604-946-5155 . www.regency-fire.com
22| P33CE-10 Direct Vent Gas Fireplace
| 23
installation RIGID PIPE VENTING ARRANGEMENTS
Vertical Terminations
(Propane & Natural Gas)
The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using one 90o elbow, with rigid pipe
vent systems for Propane and Natural Gas.
•
•
•
•
Vent must be supported at offsets.
Firestops are required at each floor level and whenever passing through a wall.
Maintain clearances to combustibles.
When using Contemporary Faceplate, unit must be raised 1".
Note: Must use optional rigid pipe adapter when using rigid vent systems (Part # 510-994).
P33CE-10 Direct Vent Gas Fireplace |
23
24
| installation
The P33CE is approved for a maximum 40 ft. straight vertical, with rigid
pipe vent systems for Propane and Natural Gas.
The shaded area in the diagram shows all allowable combinations of straight
vertical and offset to vertical terminations with rigid pipe vent systems for
Propane and Natural Gas. Maximum two 45o elbows allowed.
• Vent must be supported at offsets.
• Firestops are required at each floor level and whenever passing
through a wall.
• Maintain clearances to combustibles.
•
When using Contemporary Faceplate, unit must be raised 1".
24| P33CE-10 Direct Vent Gas Fireplace
| 25
installation RIGID PIPE VENTING ARRANGEMENTS
Horizontal Terminations
REGENCY® DIRECT VENT SYSTEM (FLEX)
(Propane & Natural Gas)
This diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45o and one 90o elbow (two 45o elbows equal one 90o
elbow).
Note: Must use optional rigid pipe adaptor (Part # 510-994) when using rigid pipe vent systems. (Refer "Rigid Pipe Venting Systems" Section)
A vent guard should be used whenever the
termination is lower than the specified minimum
or as per local codes.
Note:Regency® Direct Vent System (Flex)
is only approved for horizontal
terminations.
•
•
•
•
Minimum
Simpson Dura-Vent Center-Line
Maintain clearances to combustibles.
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
When using Contemporary Faceplate, unit must be raised 1".
Minimum
Flex Kit Center-Line
P33CE-10 Direct Vent Gas Fireplace |
25
26
| installation
Horizontal Venting with Two (2) 90o Elbows
Horizontal Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
V
H + H1
A)
1' Min.
3' Max.
B)
2' Min.
4' Max.
C)
3' Min.
5' Max.
D)
4' Min.
6' Max.
E)
5' Min.
7' Max.
F)
6' Min.
8' Max.
One 90o elbow = Two 45o elbows.
With these options, maximum
total pipe length is 30 feet
with minimum of 6 feet total
vertical and maximum 8 feet
total horizontal.
Option
H
V
H+H1+H2
A)
1' Max.
1' Min.
3' Max.
B)
2' Max.
3' Min.
5' Max.
C)
3' Max.
5' Min.
6' Max.
Please note minimum 1
foot between 90o elbows is
required.
D)
4' Max.
7' Min.
7' Max.
E)
5' Max.
9' Min.
8' Max.
F)
6' Max.
11' Min.
9' Max.
With these options,
maximum total pipe
length is 30 feet with
minimum of 11 feet
total vertical and
maximum 9 feet total
horizontal.
Please
note
minimum 1 foot
o
between 90 elbows
is required.
Horizontal Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
26| P33CE-10 Direct Vent Gas Fireplace
Option
H
V
H+H1
A)
1' Max.
1' Min.
3' Max.
B)
2' Max.
2' Min.
5' Max.
C)
3' Max.
4' Min.
6' Max.
D)
4' Max.
6' Min.
7' Max.
E)
5' Max.
8' Min.
8' Max.
With these options,
maximum total pipe
length is 30 feet with
minimum of 8 feet total
vertical and maximum
8 feet total horizontal.
Please note minimum
1 foot between 90o
elbows is required.
| 27
installation Horizontal Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
V
H
V+V1
H+H1
A)
2' Min.
1' Max.
3' Min.
4' Max.
B)
3' Min.
2' Max.
4' Min.
5' Max.
C)
4' Min.
3' Max.
6' Min.
6' Max.
D)
5' Min.
4' Max.
8' Min.
7' Max.
E)
6' Min.
5' Max.
10' Min.
8' Max.
F)
7' Min.
6' Max.
12' Min.
9' Max.
With these options,
maximum total pipe
length is 30 feet with
minimum of 12 feet
total vertical and
maximum 9 feet total
horizontal.
Please
note
minimum 1 foot
o
between 90 elbows
is required.
Vertical Venting with Two (2) 90o Elbows
Vertical Venting with Two (2) 90o Elbows
One 90 elbow = Two 45 elbows.
o
Option
A)
V
H
1' Min. 4' Max.
o
V+V1
2' Min.
B)
2' Min. 5' Max.
3' Min.
C)
3' Min. 6' Max.
4' Min.
D)
4' Min. 7' Max.
5' Min.
E)
5' Min. 8' Max.
6' Min.
One 90o elbow = Two 45o elbows.
With these options,
maximum total pipe
length is 30 feet with
minimum of 6 feet total
vertical and maximum 8
feet total horizontal.
Option
H + H1
V
A)
2' Max.
2' Min.
B)
3' Max.
3' Min.
Please note minimum
1 foot between 90 o
elbows is required.
C)
4' Max.
4' Min.
D)
5' Max.
5' Min.
E)
6' Max.
6' Min.
With these options, maximum
total pipe length is 30 feet
with minimum of 6 feet total
vertical and maximum 6 feet
total horizontal.
Please note minimum 1
foot between 90o elbows is
required.
For additional vertical venting with
2 x 90o elbows, refer to "Rigid Pipe
Venting Arrangements" Section.
P33CE-10 Direct Vent Gas Fireplace |
27
28
| installation
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
H
1' Max.
2' Max.
3' Max.
4' Max.
5' Max.
V
H + H1
1' Min. 3' Max.
2' Min. 4' Max.
3' Min.' 5' Max.
4' Min. 6' Max.
5' Min. 7' Max.
V + V1
3' Min.
5' Min.
7' Min.
9' Min.
11' Min.
With these options, max. total
pipe length is 30 feet with min.
of 11 feet total vertical and
max. 7 feet total horizontal.
Please note min. 1 foot
between 90 o elbows is
required.
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
28| P33CE-10 Direct Vent Gas Fireplace
Option
A)
B)
C)
D)
E)
F)
V
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
V + V1 With these options, max. total
4' Min. pipe length is 30 feet with min.
6' Min. of 10 feet total vertical and
7' Min. max. 8 feet total horizontal.
Please note min. 1 foot
8' Min. between 90 o elbows is
9' Min. required.
10' Min.
| 29
installation VERTICAL TERMINATION
WITH CO-LINEAR FLEX SYSTEM
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE SERVING
A SEPARATE SOLID FUEL
BURNING APPLIANCE.
Masonry chimneys may take various contours which the flexible liner will accommodate. However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the "Venting
Arrangements - Vertical Terminations" Section for
minimum and maximum heights.
Co-linear DV
Vertical Termination
Cap # 946-529
A maximum
of two certified
joiner kits
may be used
per length.
#948-305
35 ft (11m)
Required Parts:
Part #
Description
946-529
Co-linear DV Vertical
Termination Cap
948-305
3" Flex - 35 ft.
946-563
Co-Axial to Co-Linear Adapter Kit
which contains the following:
Co-linear Flex Adapter Outer Pipe
Inner Pipe Adapter
510-994
Rigid Pipe Adaptor
46DVA-E45 45o Elbow
Alternate Approved Caps
46dva-VC Vertical Termination Cap
46dva-VCH High Wind Cap
46dva-GK
3" Co-linear Adapter with flashing
Flex Liner
Exhaust
Flue
Outer
Pipe
with Kit#
946-563
Air Intake
Pipe Length
Co-Linear
Flex
Adapter
with Kit#
946-563
Rigid Pipe Adapter
# 510-994
o
45 Elbow
Inner Pipe
Adapter
with Kit#
946-563
P33CE-10 Direct Vent Gas Fireplace |
29
30
| installation
VENTING ARRANGEMENTS - VERTICAL TERMINATIONS
with Co-linear Flex System for both
Residential & Manufactured Homes
into Masonry Fireplaces
30' (9.1m) Max.
8' (2.4m) Min.
30
(762mm)
2 (51mm) max.
Vertical Height (feet)
30
Horizontal Distance (Feet)
When using Contemporary Faceplate, unit must be raised 1".
The shaded area in the diagrams show
the allowable vertical terminations.
30| P33CE-10 Direct Vent Gas Fireplace
| 31
installation UNIT INSTALLATION WITH HORIZONTAL TERMINATION
Install the vent system according to the
manufacturer's instructions included with the
components.
1) Set the unit in its desired location. Check
to determine if wall studs or roof rafters
are in the way when the venting system is
attached. If this is the case, you may want
to adjust the location of the unit. Rough in
the gas preferably on the right side of the
unit and the electrical (junction block is on
the left side) on the left.
2) Direct Vent pipe and fittings are designed
with special twist-lock connections to
connect the venting system to the appliance
flue outlet. A twist-lock appliance adaptor
is an available option that must be used in
conjunction with the Simpson Dura-Vent
Direct Vent system.
3) Put a bead of Mill-Pac inside the outer section
of the adapter and on the inner collar. Slip
the adapter over the existing inner and outer
flue collar and fasten to the outer collar only
with the 3 supplied screws (drilling pilot holes
will make this easier). Level the fireplace
and fasten it to the framing using nails or
screws through the nailing strips.
4) Assemble the desired combination of pipe
and elbows to the appliance adaptor and
twist-lock for a solid connection.
Note:
a) Twist-lock procedure: Four indentations,
located on the female ends of pipes and
fittings, are designed to slide straight
onto the male ends of adjacent pipes
and fittings, by orienting the four pipe
indentations so they match and slide
in to the four entry slots on the male
ends, Dia. 1. Push the pipe sections
completely together, then twist-lock
one section clockwise approximately
one-quarter turn, until the two sections
are fully locked. The female locking lugs
will not be visible from the outside, on
the Black Pipe or fittings. They may be
located by examining the inside of the
female ends.
NOTE: For best results and optimum perfor-
b) Horizontal runs of vent must be supported
every three feet. Wall straps are available for
this purpose.
Riser Vent
Termination
5) Mark the wall for a 10" x 10" square hole. The
center of the square hole should line up with the
centerline of the horizontal pipe. Cut and frame
the 10 inch square hole in the exterior wall where
the vent will be terminated. If the wall being
penetrated is constructed of non-combustible
material, i.e. masonry block or concrete, a
7"(178mm) diameter (7-1/2"(191mm) dia. for
flex) hole is acceptable.
Note:
a) The horizontal run of vent must be level, or
have a 1/4 inch rise for every 1 foot of run
towards the termination. Never allow the
vent to run downward. This could cause
high temperatures and may present the
possibility of a fire.
b) The location of the horizontal vent
termination on an exterior wall must meet
all local and national building codes, and
must not be blocked or obstructed. See
"Exterior Vent Terminal Locations" Section.
c) Snorkel Terminations:
For installations requiring a vertical rise on
the exterior of the building, 14-inch and 36inch tall Snorkel Terminations and the Riser
Vent as shown in Dia. 2 & 2a are available.
Follow the same installation procedures as
used for standard Horizontal Termination.
NEVER install the snorkel upside down.
mance with each approved venting system,
it is highly recommended to apply “MillPac” sealant (supplied) to every inner pipe
connection. Failure to do so may result in
drafting or performance issues not covered
under warranty.
Min. 6-1/4"*
(159mm)
proper drainage must be provided
to prevent water from entering the
Snorkel Termination. Refer to DuraVent Installation instructions for details.
Do not attempt to enclose the Snorkel
within the wall, or any other type of
enclosure.
6) The arrow on the vent cap should
be pointing up. Insure that the 1-1/2"
clearances to combustible materials are
maintained (Dia. 3). Install the termination
cap. AstroCapTM or Dura-Vent Horizontal
Termination Cap may be used.
The four wood screws provided should
be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of
sidings.
Below Grade Snorkel Installation
If the Snorkel Termination must be installed
below grade, i.e. basement application,
Diagram 3
Diagram 2
Diagram 1
Diagram 2a
*As specified in CGA B149 Installation Code.
Local codes or regulations may require different
clearances.
Note: If installing termination on a siding
covered wall, a vinyl siding standoff
or furring strips must be used to
ensure that the termination is not
recessed into the siding.
7) Before connecting the horizontal run of vent
pipe to the vent termination, slide the Wall
Thimble (Part # 620-926) over the vent
pipe.
P33CE-10 Direct Vent Gas Fireplace |
31
32
| installation
8) Slide the appliance and vent assembly towards
the wall carefully inserting the vent pipe into the
vent cap assembly. It is important that the vent
pipe extends into the vent cap sufficient distance
so as to result in a minimum pipe overlap of
1-1/4 inches. Secure the connection between
the vent pipe and the vent cap 3 sheet metal
screws.
4) Assemble the desired lengths of pipe and
elbows. Ensure that all pipes and elbow connections are in the fully twist-locked position
and sealed.
Diagram 4
9) Install wall thimble in the center of the 10" square
and attach with wood screws (Diagram 4).
Roof Pitch
NOTE: For best results and optimum performance with each approved venting system, it is
highly recommended to apply “Mill-Pac” sealant
(supplied) to every inner pipe connection. Failure
to do so may result in drafting or performance
issues not covered under warranty.
Diagram 4
UNIT INSTALLATION
WITH VERTICAL
TERMINATION
5) Cut a hole in the roof centered on the small
drilled hole placed in the roof in Step 2. The hole
should be of sufficient size to meet the minimum
requirements for clearance to combustibles
of 1-1/2". Slip the flashing under the shingles
(shingles should overlap half the flashing) as
per Diagram 3.
1) Maintain the 1-1/2" clearances (air spaces) to
combustibles when passing through ceilings,
walls, roofs, enclosures, attic rafter, or other
nearby combustible surfaces. Do not pack air
spaces with insulation. Check "Venting" Sections
for the maximum vertical rise
o f
the venting system and the
maximum horizontal offset
limitations.
2)S e t t h e g a s a p p l i a n c e
i n
its desired location. Drop
a
plumb bob down from the ceiling
t o
the position of the appliance
flue exit, and mark the location
where the vent will penetrate
the ceiling. Drill a small
hole at this point. Next,
drop a plumb bob from
the roof to the hole
previously drilled
in
the ceiling, and mark the
Diagram 1
spot where the vent will penetrate the roof.
3) A Firestop spacer must be installed in the floor
or ceiling of every level. To install the Firestop
spacer in a flat ceiling or wall, cut a 10 inch square
hole. Frame the hole as shown in Diagram 2
and install the firestop.
Diagram 2
32| P33CE-10 Direct Vent Gas Fireplace
flat to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
Minimum Vent Height
Feet
Meters
2
0.61
2
0.61
2
0.61
2.5
0.76
3.25
0.99
4
1.22
5
1.52
6
1.83
7
2.13
7.5
2.29
8
2.44
8) Install the vertical termination cap by twistlocking it.
Note: Any closets or storage spaces, which
the vent passes through must be
enclosed.
GAS LINE
INSTALLATION
Diagram 3: The upper half of the flashing is installed under the roofing material and not nailed
down until the chimney is installed. This allows
for small adjustments.
The gas line is brought through the right side of
the appliance. The gas valve is situated on the
right hand side of the unit and the gas inlet is on
the right hand side of the valve.
6) Continue to assemble pipe lengths.
The gas line connection may be made of rigid pipe,
copper pipe or an approved flex connector. (If you
are using rigid pipe, ensure that the valve can be
removed for servicing.) Since some municipalities
have additional local codes it is always best to
consult with your local authorities and the CAN/
CGA B149 installation code.
Note: If an offset is necessary in the attic to
avoid obstructions, it is important to
support the vent pipe every 3 feet, to
avoid excessive stress on the elbows,
and possible separation. Wall straps
are available for this purpose.
Galvanized pipe is desirable above the roofline
due to its higher corrosion resistance. Continue
to add pipe sections through the flashing until
the height of the vent cap meets the minimum
height requirements specified in Dia. 4 or local
codes. Note that for steep roof pitches, the
vertical height must be increased. A poor
draft, or down drafting can result from high
wind conditions near big trees or adjoining
roof lines, in these cases, increasing the
vent height may solve the problem.
7) Ensure vent is vertical and secure the base
of the flashing to the roof with roofing rails,
slide storm collar over the pipe section and
seal with a mastic.
For USA installations follow local codes and/or the
current National Fuel Gas Code, ANSI Z223.1.
When using copper or flex connectors use only
approved fittings. Always provide a union so that
gas lines can be easily disconnected for servicing.
Flare nuts for copper lines and flex connectors
are usually considered to meet this requirement.
Important: Always check for gas leaks with a
soap and water solution or gas leak detector.
Do not use open flame for leak testing.
| 33
installation PILOT ADJUSTMENT
Periodically check the pilot flames. Correct
flame pattern has two strong blue flames:
1 flowing around the flame sensor and 1
flowing across the burner (it does not have
to be touching the burner).
Burner
Burner Inlet Orifice Sizes:
#44
Max. Input Rating
20,000 Btu/h
Min. Input Rating
14,000 Btu/h
Supply Pressure
min.5.0" w.c.
Manifold Pressure
(High)
3.5"+/- 0.2"
w.c.
Flame Sensor
P33CE-LP10 System Data
Ignitor
Pilot
Note: If you have an incorrect flame pattern,
contact your Regency® dealer for
further instructions.
Incorrect flame pattern will have small,
probably yellow flames, not coming into
proper contact with the rear burner or flame
sensor. Burner Inlet Orifice Sizes:
#55
Max. Input Rating
19,500 Btu/h
Min. Input Rating
15,500 Btu/h
Supply Pressure
min.11.0" w.c.
Manifold Pressure
(High)
1 0 " + / 0.2"w.c.
HIGH ELEVATION
This unit is approved in Canada for altitude to
4500 ft. (CAN/CGA-2.17-M91). For Natural Gas
installations above 4500 ft. follow current CAN/
CGA-B149.1.
885 S.I.T. VALVE
DESCRIPTION
1)
2)
3)
4)
5)
6)
7)
GAS PIPE PRESSURE
TESTING
P33CE-NG10 System Data
The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than 1/2 psig. (3.45 kPa). Disconnect piping
from valve at pressures over 1/2 psig.
The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.
Note: To properly check gas pressure, both
inlet and manifold pressures should
be checked using the valve pressure
ports on the valve.
1) Make sure the switch is in the "OFF" position.
2) Loosen the "IN" and/or "OUT" pressure tap(s),
turning counterclockwise with a 1/8" wide flat
screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4) Light the pilot by turning the switch to "ON"
position.
5) The pressure check should be carried out with
the unit burning and the setting should be within
the limits specified on the safety label.
6) When finished reading manometer, turn off the
gas valve, disconnect the hose and tighten the
screw (clockwise) with a 1/8" flat screwdriver.
Note: Screw should be snug, but do not
over tighten.
3
4
2
1
6 Stage flame adjustment
Pilot adjustment
Outlet Pressure Tap
Inlet Pressure Tap
Pilot Outlet
Main Gas Outlet
Main Gas Inlet
4
7
3
2
5
1
6
P33CE-10 Direct Vent Gas Fireplace 7
|
33
34
| installation
P33E
Conversion from NG to LPG
CONVERSION
NG TO
for P33CE using SIT FROM
886 NOVA
GasLP
Valve
For P33CE Using SIT 885 NOVA Gas Valve
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT
DO NOT DO THIS CONVERSION!!
7.
Each Kit contains one LPG
Conversion Kit
LPG Conversion Kit Contains:
Qty. Part #
Description
1
1
904-575
918-590
1
1
1
908-528
904-529
910-101
1
1
911-009
919-139
Burner Orifice #55
Decal "Converted to
LPG"
Red "LPG" label
5/32" Allen Key
LPG Injector
(Pilot Orifice)
Hi/Lo Conversion LP
Instruction Sheet
5. Undo clip and remove pilot cap to
expose pilot orifice.
Burner Orifice
Installation of the LPG
Conversion Kit:
1. Shut off the gas supply.
2.
Remove burner orifice with a 1/2"
wrench and discard. Use another wrench
to hold on to the elbow behind
the orifice.
Remove the mesh barrier (see manual)
and glass door.
8.
Reinstall new burner orifice LPG
stamped #55 and tighten.
9.
Remove regulator and discard. Install the
Hi/Lo pressure regulator onto the valve
with 2 screws as shown below.
Clip
a) Release the two hooks from the
bottom of the glass door.
10. Attach the label “This unit has been
converted to LPG” near or on top of the
serial # decal.
11. Replace yellow “NG” label with red “LPG”
label.
Pilot Cap
b) Swing the door out 45 degrees from
the bottom - then lift up and out.
6.
Unscrew the pilot orifice with the Allen
key and replace with the LPG pilot orifice
in the kit and replace pilot cap.
3. Remove logs and brick panels if
installed.
4.
12. Reverse step 3 - 1
13. Check for gas leaks.
14. Check inlet and outlet pressures.
15. Check operation of flame control.
Remove the 2 screws holding the Burner
Assembly to the firebox base. Push the
Burner Assembly to the left and lift out.
Installer Notice:
These instructions must remain
with the appliance.
Remove the 2 screws, push Burner
Assembly to the left and lift out.
34| P33CE-10 Direct Vent Gas Fireplace
919-139b
1
06.10.14
| 35
installation OPTIONAL BRICK
PANELS
1) Remove the mesh barrier and glass door.
Remove logs.
2) Attach the 2 Rear Brick Retaining clips to the
rear wall. Loosen the screws in the top and
rear wall of the firebox and slide the retaining
clips into position (tight against the firebox top)
and then tighten the screws.
LOG SET INSTALLATION
D) 251
Read the instructions below carefully
and refer to the diagrams. If logs
are broken do not use the unit until
they are replaced. Broken logs can
interfere with the pilot operation.
The 3-digit numbers (i.e. 250) are
molded into the rear of each log.
Log Kit # 431-930 contains the
following pieces:
A) 250
B) 254
C) 253
D) 251
E) 252
F)
G)
H)
I)
Note: The logs must not be in the unit.
3) Insert the back brick panel by carefully
slipping it between the back wall of the
firebox and the rear log bracket.
A) 250
Rear Log
Middle Cross Log
Front Left Cross Log
Rear Left Log
Front Right Cross Log
Embers
902-156
Vermiculite
902-179
Rock Wool
902-153
Platinum Embers
946-669
B) 254
C) 253
E) 252
4) Place Log 254 on the front right side of the
burner. Push the back of the log against
the 2 brackets with the notch on the bottom
right side of the log fitting into the right side
of the grate.
Notch
(supplied with packaged manual)
NOTE: If you will be installing the optional
Brick Panels, install the Brick Panels
prior to installing the logs.
254
1) Carefully remove the logs from the box and
unwrap them. The logs are fragile, handle
with care - do not force into position.
2) Sprinkle the vermiculite and embers around
the firebox base.
4) Put the side panels in next. Slide them in from
the front and push them flat up against the
wall. Be very careful not to scratch them on
the firebox hardware.
Bracket
Bracket
250
254
Vermiculite
Vermiculite
Vermiculite
3) Place the Log 250 on the rear log support
pins with the flat side to the back.
5) Position Log 253 across the cutouts in
Logs 250 and 254 with the notch on the
left side of the log fitting into the 2nd grate
tab.
Cutouts
250
253
5) Slide the Top Brick Panel into position and slide
the Top Brick Retaining clips so that they hold
the Top Brick Panel in place and tighten down
the screws.
250
254
2nd Grate Tab
P33CE-10 Direct Vent Gas Fireplace |
35
36
| installation
25
3
250
8) Pull off ember size pieces of rock wool and
gently place them on the front of the burner
tray in the places shown in the photo below.
Do not compress the rock wool, leave it
loose.
254
Separate platinum embers and place them
on the front of the burner on and around the
rock wool.
6) Place the bottom left front edge of Log 251
against the left edge of the burner tray and
rest the log on the cutout on Log 253.
250
Place rock wool in these 2 locations
on the burner tray.
25
3
251
254
Cutout
7) Position Log 252 across the cutouts in Logs
254 and 253. The notch in the bottom right
end fitting against the 5th grate tab.
2
25
25
3
254
5th Grate Tab
250
25
3
251
254
25
2
36| P33CE-10 Direct Vent Gas Fireplace
9) Test fire to ensure proper light off (make
sure flame flows smoothly from one end of
burner to the other). If there is any flame
hesitation, check that area for any blockage
of the burner ports.
| 37
installation GLASS DOOR AND MESH BARRIER INSTALLATION
STANDARD FLUSH DOOR
Use the hook to pull the spring out until you can put the hook into the slot on
the bottom door bracket. Repeat for 2nd spring. See Diagram 4.
Both the standard flush door comes with a black frame. Install the glass
door by hooking the top door flange onto the top of the unit and swing the door
towards the unit, Diagram 2. Be careful that the glass gasket does not roll up;
there must be a gap between the gasket and the door lip to ensure that the
door sits securely on the unit. See Diagram 3.
Diagram 4
To remove the flush door, reverse the above steps.
MESH BARRIER
1. To remove the mesh barrier, grasp mesh barrier on both sides from the bottom. Lift up and out slightly to release from bottom magnets and to release
hooks on mesh frame from brackets inside unit (see below).
Diagram 1
Hooks on mesh barrier frame
2. When hooks are clear of the bracket–tilt mesh frame out slightly from the
bottom and manoeuvre mesh out.
Diagram 2
3. To reinstall–reverse steps.
Diagram 3
P33CE-10 Direct Vent Gas Fireplace |
37
38
| installation
OPTIONAL 4-SIDED FACEPLATE INSTALLATION
If installing the optional faceplate ensure the combustible
and non combustible material around the unit are installed
flush with the unit. (See Diagram 1 below).
The faceplate cannot be installed if materials are not flush.
3. Line up the middle rib on backside of faceplate with middle indent on bracket.
This will centre the faceplate and allow 1/16" adjustment from side to side.
Combustible
Material
Non-combustible Material (3-1/2" x 36")
Nailing Strip -1/2" back from unit face
Middle Rib on Faceplate
Diagram 4 -Line up faceplate and bracket.
4. Lift faceplate up and lower gently onto bracket.
Combustible
Material
Diagram 1- Materials flush w/unit.
1. Install 2 middle screws on unit face - do not tighten. Slide
bracket over screws then tighten. Install 2 outer screws .
Install middle 2 screws on
to unit first
Diagram 2 -Bracket screw locations on unit.
Diagram 5 -Hang faceplate on bracket
2. Install four (4) wood screws, two (2) on each side of the
bracket into the wall studs as shown below.
Diagram 6 -Final Install
Diagram 3 -Bracket screw locations.
38| P33CE-10 Direct Vent Gas Fireplace
| 39
installation WIRING DIAGRAM
This heater does not require a 120V A.C. supply for operation but it is highly recommended to install the supplied AC adaptor to eliminate the need for
batteries. In case of a power failure, the burner switch and the optional remote control will continue to operate if batteries are installed in the receiver..
However, a 120V A.C. power supply is needed for the fan/blower operation.
(Do not cut the ground terminal off under any circumstances.)
NOTE: Even if the fan is not purchased with the unit, it is still a good idea to bring power to the receptacle box (provided with the unit) in case
the fan is installed at a later date.
Proflame System
Configuration
885
886 GTMF
Wire Diagram
SureFire™ Switch
AC Adaptor
Caution: Ensure that the wires do not touch any
hot surfaces and are away from sharp edges.
CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation.
1 of 10
P33CE-10 Direct Vent Gas Fireplace |
39
40
| installation
OPTIONAL WALL THERMOSTAT INSTALLATION
A wall thermostat may be installed if desired.
Recommended: The Wall Thermostat should be mounted beside the Remote/Unit Receiver which comes standard with the appliance.
1) Run wires from thermostat into the unit.
2) Remove the green wire marked (TH) at the white connector-shown below. The noted wires will be located near the gas valve.
Green Wires
CAUTION
Do not wire
Thermostat wires
to 120V wire.
White Connector
Disconnect greenTH wire
4) Connect the other thermostat lead to male connector disconnected
from Step1using a female spade connector - see picture below.
3) C
onnect one thermostat lead to female connector, using male spade connector - see picture below.
hen complete turn remote receiver to the ON position.
W
Unit will now operate using the wall thermostat.
OTE: When the remote receiver is set to ON position, the
N
remote control transmitter and all of its features are now disabled.
40| P33CE-10 Direct Vent Gas Fireplace
P33CE
| 41
installation
INSTALLING THE OPTIONAL FAN
OPTIONAL FAN INSTALLATION
Follow these instructions before the Initial installation into the framing.
If installing the optional fan into an Existing installation see the instructions on the following page.
5. Slide the thermodisc/cover assembly on to the bracket clip on the
underside of the firebox.
120 Volt AC power is needed for the fan. The fan can be hard wired if desired. The outlet should be installed in the receptacle box on the left hand
side by a qualified electrician. The neutral (wider) slot of the polarized
outlet should be at the top.
Unit must be grounded at all times. Do not cut the ground terminal
off under any circumstances.
1. Remove lower base cover by tilting forward and lifting out each side to
release.
2. Loosen four (4) screws (two on each side) inside of the bottom panel of
the clean front, slide panel out.
Thermodisc Clip
6. Install the Fan Control Module (FCM) on the base of the unit to the left
of the gas valve. Plug the FCM into the outlet.
7. Plug in the fan power cord to the Fan Control Module into the outlet
marked “Fan”. Plug the FCM-COM wire from the remote control wiring
harness into the location on the Fan Control Module marked “COM”.
Turn the switch on the Fan Control Module to the ON position. ON is to
the left. The “O” is the off position
3. Turn the fan base on its side (with base facing forward) and then slide
the fan in towards the rear of the unit. Turn the fan upright and slip it
over the two mounting studs. Take care not to damage the insulation on
the fan base.
Ensure the fan blades do not rub against the valve tubing.
TO REMOVE THE FAN
1) Turn the power off.
2) Reverse the above instructions
MAINTENANCE: The sealed bearings are lubricated so there is no need
to lubricate them further. Extra lubricant will cause more lint and dust to
build up causing the premature failure of the bearings.
Regular cleaning and vacuuming of the fan area will add to the life of the
motor
4. Connect the power cord and fan ground wires to the ground lug. Refer
to wiring diagram
919-427
IMPORTANT:
THESE FANS COLLECT A LOT OF DUST FROM
WITHIN YOUR HOME. ENSURE YOU MAINTAIN THESE
FAN MOTORS ON A REGULAR BASIS BY VACUUMING
THE FAN BLADES AND THE HOUSING WITH A SOFT
BRUSH NOZZLE.
P33CE-10 Direct Vent Gas Fireplace 1
08/26/14
|
41
P33CE
42
| installation
Follow these instructions for Existing Installations.
7. Manoeuvre the fan into the valve tray opening at the base of the
firebox
120 Volt AC power is needed for the fan. The fan can be hard wired if
desired. The outlet should be installed in the receptacle box on the left
hand side by a qualified electrician. The neutral (wider) slot of the polarized outlet should be at the top.
Unit must be grounded at all times. Do not cut the ground terminal off
under any circumstances.
1. Shut off the power and disconnect the gas supply.
2. Remove Flush Door, mesh screen and logs. Remove the inner panels
(if installed).
3. Remove the burner by removing 2 screws in the locations shown b
Diagram 5
8. Secure the fan by pushing it down onto the mounting pins located on the floor of the unit. Take care not to damage the insulation
on the fan base. Ensure the fan blades do not rub against the
valve tubing.
Diagram 1: Remove the 2 screws to remove
burner.
4.
Slide burner to the left and lift out.(See Diagram 2).
Diagram 6
9. Connect fan ground wire to to the ground lug. Refer to wiring
diagram
10. Slide the thermodisc/cover assembly on to the bracket clip on
the underside of the firebox.
Diagram 2
5.
Remove 2 screws to remove Rear Log Stand (See Diagram 3).
screws
Rear Log Stand
Diagram 7
11. Plug in the fan power cord to the Fan Control Module into the
outlet marked “Fan”. Plug the FCM-COM wire from the remote
control wiring harness into the location on the Fan Control
Module marked “COM”. Turn the switch on theFan Control
Module to the On position. On is to the left. The “O” is the off
position.
Diagram 3
6.
Remove the 12 screws securing the valve tray assembly in place
(Diagram 4) and then lift the entire assembly out.
Diagram 8
Diagram 4 Valve Tray Assembly
42| P33CE-10 Direct Vent Gas Fireplace
919-427
2
08/26/14
P33CE
| 43
installation TO REMOVE THE FAN
1) Shut the power off.
2) Reverse the above instructions.
Note: The bearings are lubricated for life. Do not lubricate them.
Make sure you vacuum the fan area on a regular basis.
Diagram 9
IMPORTANT:
These fans collect a lot of dust from within your
home. Ensure you maintain these fan motors on
a regular basis by vacuuming out the fan blades
and housing using a soft brush nozzle.
Diagram 10
11. See the Proflame instructions for coding the remote handheld to
the receiver and for operating instructions.
12. Reverse Steps 6 -1 to complete the installation.
919-427
3
P33CE-10 Direct Vent Gas Fireplace |
08/26/14
43
44
| installation
WIRING DIAGRAM WITH OPTIONAL FAN
SureFire™ Switch
Caution: Ensure that the wires do not touch any
hot surfaces and are away from sharp edges.
CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation.
44| P33CE-10 Direct Vent Gas Fireplace
| 45
operating instructions OPERATING
INSTRUCTIONS
AERATION
ADJUSTMENT
1) Read and understand these instructions
before operating this appliance.
The air shutter can be adjusted by moving
the adjusting wire up or down. The wire is
accessed through the bottom opening. Open
the air shutter for a blue flame or close for a
yellower flame. The burner aeration is factory
set but may need adjusting due to either the
local gas supply or altitude.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
4) Make sure the glass in the door frame is
properly positioned. Never operate the
appliance with the glass removed.
5) Verify that the venting and cap are
unobstructed.
6) Ensure that the brick panels are installed.
Minimum Air Shutter Opening:
3/16" Natural Gas - Orifice # 44
3/8"
Propane -
Orifice # 54
CAUTION: Carbon will be produced if air
shutter is closed too much.
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
Air
shutter
FIRST FIRE
The first fire in your fireplace is part of the
paint curing process. To ensure that the paint
is properly cured, it is recommended that you
burn your fireplace for at least four (4) hours the
first time you use it with the fan on.
When first operated, the unit will release an odour
caused by the curing of the paint, the burning
off of any oils remaining from manufacturing.
Smoke detectors in the house may go off at
this time. Open a few windows to ventilate the
room for a couple of hours.
The glass panel may require cleaning after the
unit has cooled down. DO NOT ATTEMPT TO
CLEAN THE GLASS WHILE IT IS HOT.
Note: When the glass is cold and the
appliance is lit, it may cause
condensation and fog the glass.
This condensation is normal and
will disappear in a few minutes as
the glass heats up.
wire
Adjustment Wire: push to close
or pull to open aeration cap
Closed - Tall yellow
Open - Short blue
Note: Any damage due to carboning resulting
from improperly setting the aeration
controls is NOT covered under warranty.
Note: Aeration Adjustment should only be
performed by an authorized Regency®
Installer at the time of installation or
service.
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
During the first few fires, a white film
may develop on the glass front as part
of the curing process. The glass should
be cleaned or the film will bake on and
become very difficult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
P33CE-10 Direct Vent Gas Fireplace |
45
46
| operating instructions
LIGHTING PROCEDURE
IMPORTANT: The remote control system supplied with this appliance has
several options for starting/operating the appliance using the power button
and ON/OFF key on the hand held transmitter.
Prior to operating this appliance, please read the remote control operating
instructions (packaged with remote control) to understand how to operate
this remote control system. Option to download remote functions video
with QR code below.
Proflame
video
1. Ensure the wall switch/receiver is in the remote position. (see Diagram 1).
Set Switch to
Remote
3. After approximately 4 seconds the spark ignition system will spark for 60
seconds to light the main burner.
4. The unit will turn on.
Note: The first try for ignition will last approximately 60 seconds. If there is no
flame ignition (rectification) the board will stop sparking for approximately
35 seconds. After wait time , the board will start second try for ignition by
sparking for approximately 60 seconds . If there is still no positive ignition
the board will go into lock out.
The system will need to be reset as follows:
a) Turn the system off using ON/OFF switch or press ON/OFF button - if
using optional remote.
b) After approximately 2 seconds turn on ON/OFF switch or press ON/OFF
button if using optional remote.
c) Repeat step 2.
SHUTDOWN
PROCEDURE
Diagram 1
2. Press and release the ON/OFF button on the remote handheld transmitter (see Diagram 2). An audible beep should be heard from the receiver.
1. Turn the wall mounted switch or remote to the "OFF" position.
2. Press "OFF" on the remote control.
3. Turn the gas control knob to the "OFF" position to turn off the pilot.
ON/OFF
Button
Diagram 2
Remote shown in Manual Mode on Hi
46| P33CE-10 Direct Vent Gas Fireplace
| 47
operating instructions COPY OF THE LIGHTING PLATE INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
This appliance must be installed in accordance with local codes, if any;
if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or
Natural Gas and Propane Installation Codes, CSA B149.1.
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life. Improper installation, adjustment,
alteration, service or maintenance can cause injury or property damage. Refer to the owner’s
information manual provided with this appliance. For assistance or additional information
consult a qualified installer, service agency or gas supplier.
AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice
risquede déclencher un incendie ou une explosion entraînant des dommages, des blessures ou
la mort.
Une installation, d'ajustement, de modification, de service ou d'entretien peut provoquer
des blessures ou des dommages matériels. Reportez-vous au manuel du propriétaire de
l'information fournie avec cet appareil. Pour obtenir de l'aide ou des informations supplémentaires consulter un installateur qualifié, une agence de service ou fournisseur de gaz.
A) This appliance is equipped with an ignition device which automatically lights the pilot.
Do not try to light the pilot by hand.
B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electric switch, do not use any phone in your building.
- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire department.
C) Do not use this appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and replace any part of the control system and any
gas control which has been underwater.
A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse.
Ne tentez pas d’allumer la veilleuse manuellement.
B) AVANT DE FAIRE FONCTIONNER, reniflez tout autour de l’appareil pour déceler une odeur
de gaz. Reniflez près du plancher, car certains gaz sont pluslourds que l’air et peuvent
s’accumuler au niveau du sol.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne pas tenter d’allumer d’appareil
• Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se trouvant dans le
bâtiment.
• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les
instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies
C) N’utilisez pas cet appareil s’il a été plongé dansl’eau, même partiellement. Faites inspecter l’appareil par un technicien qualifié et remplacez toute partie du système de contrôle et toute commande qui ont été plongés dans l’eau.
CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface
temperatures keep children, clothing and furniture, gasoline and other liquids having flammable
vapors away. Keep burner and control compartment clean. See installation and operating
instructions accompanying appliance.
LIGHTING INSTRUCTIONS
1) Ensure the wall switch/receiver is in the remote position.
2) Press and release the ON/OFF button on the remote handheld transmitter. An audible beep should be
heard from the receiver.
3) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.
4) The unit will turn on.
Note: The first attempt to ignition will last approximately 60 seconds. If there is no flame ignition (rectification) the board will stop sparking for approximately 35 seconds. After this wait time, the board will start a
second try for ignition by sparking for approximately 60 seconds. If there is still no positive ignition after the
second attempt the board will go into lock out.
The system will need to be reset as follows (after going into lock out mode):
a) Wait 5 minutes - turn the system off using ON/OFF switch or press ON/OFF button if using
remote
b) After approximately 2 seconds turn on ON/OFF switch or press ON/OFF button if using remote.
c) Unit will repeat step 2.
1) S’assurer que l’interrupteur mural/récepteur soit en position télécommande.
2) Appuyer sur la touche ON/OFF de la télécommande et relâcher. Un bip sonore se fera entendre depuis le
récepteur
3) Après environ 4 secondes, le système d'allumage des étincelles pendant 60 secondes pour allumer le
brûleur principal.
4) Les flammes s’allumeront.
Remarque : Au premier allumage, le système tente d’allumer les flammes pendant 60 secondes. Si l’essai
est infructueux, le système fait une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectification.
Ce délai écoulé, le système tente à nouveau d'allumer les flammes en produisant des étincelles pendant 60
secondes. Si les flammes ne s’allument toujours pas, le système se met en mode verrouillage.
Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) :
a) Attendre 5 minutes et éteindre l’appareil en réglant l’interrupteur à la position « OFF »;
b) Attendre 2 secondes et rallumer le système à l’aide de l’interrupteur ou de la télécommande.
c) L'unité répétera l'étape 2.
TO TURN OFF GAS APPLIANCE
1)
2)
Turn the wall mounted switch or remote to the "OFF" position.
If service is to be performed–you must disconnect power and shut off gas to the unit.
1)
2)
Utilisez l'interrupteur murale ON/OFF du Brûleur ou du contrôle à distance pour éteindre le brûleur.
Si le service est effectuée–vous devez débrancher l'alimentation et coupez le gaz à l'unité.
DO NOT REMOVE THIS INSTRUCTION PLATE
919-401a
P33CE-10 Direct Vent Gas Fireplace |
47
48
| maintenance
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds
from your gas appliance. This is perfectly normal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listed below are some examples. All are normal
operating sounds and should not be considered
as defects in your appliance.
Blower:
Regency® gas appliances use high tech blowers
to push heated air farther into the room. It is not
unusual for the fan to make a "whirring" sound
when ON. This sound will increase or decrease
in volume depending on the speed setting of
your fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a different
gauge material from the rest of the firebox and
body. Therefore, the varying thicknesses of steel
will expand and contract at slightly different
rates which can cause "ticking" and "cracking"
sounds. You should also be aware that as there
are temperature changes within the unit these
sounds will likely re-occur. Again, this is normal
for steel fireboxes.
Blower Thermodisc:
When this thermally activated switch turns ON
it will create a small "clicking" sound. This is the
switch contacts closing and is normal.
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
48| P33CE-10 Direct Vent Gas Fireplace
MAINTENANCE
INSTRUCTIONS
GENERAL VENT
MAINTENANCE
1) Always turn off the gas valve before cleaning.
For relighting, refer to lighting instructions.
Keep the burner and control compartment
clean by brushing and vacuuming at least
once a year. When cleaning the logs, use a
soft clean paint brush as the logs are fragile
and easily damaged.
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
2) Clean appliance and door with a damp
cloth (never when unit is hot). Never use
an abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner.
The glass should be cleaned when it
starts looking cloudy.
3) The heater is finished in a heat resistant
paint and should only be refinished with heat
resistant paint. Regency® uses StoveBright
Paint - Metallic Black #6309.
4) Make a periodic check of burner for proper
position and condition. Visually check the
flame of the burner periodically, making sure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
5) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or streaks,
and in extreme cases, holes. These components should be replaced immediately.
2) Remove the Cap, and shine a flashlight
down the Vent. Remove any bird nests,
or other foreign material.
3) Check for evidences of excessive
condensation, such as water droplets
forming in the inner liner, and subsequently
dripping out the joints, Continuous
condensation can cause corrosion of
caps, pipe, and fittings. It may be caused
by having excessive lateral runs, too many
elbows, and exterior portions of the system
being exposed to cold weather.
4) Inspect joints, to verify that no pipe
sections or fittings have been disturbed,
and consequently loosened. Also check
mechanical supports such as Wall Straps,
or plumbers' tape for rigidity.
Note: Never operate the appliance without the
glass properly secured in place.
LOG REPLACEMENT
6) Do not use this appliance if any part has been
under water. Immediately call a qualified
service technician to inspect the appliance
and to replace nay part of the control system
and any gas control which has been under
water.
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door and carefully remove the
logs. (The pilot light generates enough heat to
burn someone.) If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagrams under Log
Installation.
7) Verify operation after servicing.
Note: Improper positioning of logs may
create carbon build-up and will
severely alter the unit's performance
which is not covered under warranty.
| 49
maintenance GLASS GASKET
Flush Glass Replacement
If the glass gasket requires replacement use
a tadpole glass gasket for the Flush Front (Part
# 936-155).
Remove the flush door front. Remove the 4
glass clips from each corner. Slide in the new
replacement glass. Push the 4 glass clips
back onto the frame. The glass must have
gasketing around it.
DOOR GLASS
Your Regency® fireplace is supplied with high
temperature, 5mm Neoceram ceramic glass that
will withstand the highest heat that your unit will
produce. If your glass requires cleaning, we
recommend using an approved glass cleaner
available at all authorized dealers. Do not use
abrasive materials. Do not clean the glass
when hot.
In the event that you break your glass by impact,
purchase your replacement from an authorized
Regency® dealer only, and follow our step-bystep instructions for replacement.
WARNING: Do not operate the
appliance with the glass panels
removed, cracked or broken.
Replacement of the glass panels
should be done by a licensed or
qualified service person.
Caution: Wear gloves when removing
damaged or broken glass.
P33CE-10 Direct Vent Gas Fireplace |
49
50
| maintenance
REMOVING VALVE
7. Remove the 12 screws securing the valve tray assembly in place
(Diagram 4) and then lift the entire assembly out.
1. Shut off the gas supply.
2. Remove the mesh barrier and flush glass door–see instructions in
manual.
3. Remove the burner/grate assembly by removing the two screws
and then lift the burner assembly out.
Diagram 4 Valve Tray Assembly
8. Remove valve tray assembly.
Diagram 1: Remove the left and right screws and then lift out the
burner/grate assembly.
4. Remove the rear log stand by removing the 2 screws.
screws
Diagram 5: Lift out Valve Tray Assembly
Rear Log Stand
INSTALLING VALVE
Ground
2. Reverse steps 7-1.
Diagram 2
5. Disconnect the inlet gas line.
6. Disconnect the EV1, EV2, and ground wires from the valve - as shown
below.
Diagram 3
EV1
50| P33CE-10 Direct Vent Gas Fireplace
1. Install new valve assembly.
EV2
| 51
parts list MAIN ASSEMBLY
Part #
Description
Part #
Description
433-525
Burner Assembly
910-572
Remote Receiver
2
910-142
Fan Thermodisc
910-592
Remote Handheld Transmitter
3
438-574/P
Valve Assembly - NG
911-127
Receiver Compartment Door
438-576/P
Valve Assembly - LP
911-137
Pilot Clip
438-917
Fan Assembly
910-331/P
Fan Motor Only
7
438-512
Clean Front Assembly
5
438-529
Mesh Guard
8
**
Firebox Assembly
6
433-538
Glass Door Assembly
**
Not a replacement part
940-380/P
Replacement Glass w/Gasket
911-012
Digital Fireplace Control
919-364
Manual
911-037
Flame Sense
911-038
Flame Electrode
910-432
Pilot Tube w/ nuts
911-039
Pilot Hood
910-100
Pilot Orifice - NG
910-101
Pilot Orifice - LP
911-013
Valve Wiring Harness
911-032
Remote Wiring Harness
1
4
P33CE-10 Direct Vent Gas Fireplace |
51
52
| parts list
BURNER & LOG ASSEMBLY
Part Description
53)430-055
57)911-084
911-085
Gasket - Valve Access Plate - NG/LP
Valve SIT - NG
Valve SIT - LP
58)*
59)*
60)*
66)911-006
911-007
904-568
904-575
936-170
67)*
68)W840470
79)433-525
82)433-024
83)*
85)431-930
86)430-097
87)433-018
Valve Bracket
Firebox Base
Valve Tray
Pilot Assy - S.I.T. - NG
Pilot Assy - S.I.T. - LP
Orifice #44 - Natural Gas
Orifice #55 - Propane
Orifice Gasket
Pilot Holder
Pilot Assembly Gasket
Burner Assy - NG/LP
Burner Grate Assembly - NG/LP
Rear Log Support Bracket - NG/LP
Log Set
Air Deflector-Left
Air Deflector-Right
66
85
83
86
82
*Not available as a replacement part.
87
68
79
67
68
60
53
59
58
57
LO
55
52| P33CE-10 Direct Vent Gas Fireplace
notes | 53
P33CE-10 Direct Vent Gas Fireplace |
53
54
notes
| 54| P33CE-10 Direct Vent Gas Fireplace
| 55
warranty Gas Product Warranty 2015
Regency® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our facility. Regency® Fireplace Products is pleased to extend this limited lifetime warranty to the original purchaser of a Regency® Product. This
warranty is not transferable.
The Warranty: Limited Lifetime:
The combustion chamber, heat exchanger, burner tubes/pans, logs, glass crystals, glass beads,ceramic spa stones, pebbles, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime Warranty for five (5) years for parts and subsidized labour* and parts only thereafter.
Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for five (5) years and parts only thereafter from date of purchase.
External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date of
purchase and parts only thereafter.
Special Finishes - One year on stainless steel panels, enamel panels, Verona glass surrounds, stainless steel inner/outer door frames, inlays, nickel overlays, nickel faceplates,
brushed nickel and antique copper full screens and doors. You can expect some changes in color as the product "ages" with constant heating and cooling. Regency® warranties the
product for any manufacturing defects on the original product. However, the manufacturers warranty does not cover changing colors and marks, i.e.. finger prints, etc. applied after the
purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.
Electrical and mechanical components such as blowers, fan motors, switches, wiring, thermodiscs, Regency® remote controls, spill switches, thermopiles, thermocouples, pilot assembly, Flame sensors, electrodes, fan control modules, IFC/DFC fireplace controls, AC adaptors, and gas valves are covered for two years parts and one year subsidized labour* from
the date of purchase. Blowers and valves replaced under warranty are considered repairs and continue as if new with appliance. i.e. twelve (12) months from original purchase date of
appliance with a minimum of three (3) months coverage from date of replacement.
Regency® venting components are covered parts and subsidized labour* for three (3) years from date of purchase.
Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. Warranty.
Repair/replacement parts purchased by the consumer from Regency® after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any item
shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at Regency's option, through an accredited distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
Porcelain/Enamel - Absolute perfection is neither guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of installation. Reported damage after this time will be subject to rejection.
It is the general practice of Regency® to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to Regency® and evaluated for manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your Regency® product. Regency® will not be liable for results or costs of workmanship from
unauthorized service persons or dealers.
At all times Regency® reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to Regency® by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name, purchase date, serial #, type of unit, problem, and part or parts requested, a copy of the bill of sale/proof of purchase must also accompany any submitted claims, without this information
the warranty will be invalid.
Exclusions:
This limited Lifetime Warranty does not extend to or include paint, batteries, volcanic stones, lava embers, rockwool, door handles, platinum embers, embaglow embers, door or glass
gasketing or trim.
At no time will Regency® be liable for any consequential damages which exceed the purchase price of the unit. Regency® has no obligation to enhance or modify any unit once manufactured. i.e.. as products evolve, field modifications or upgrades will not be performed.
Regency® will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence or
accident, spillage or down drafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical systems
such as furnaces, fans, clothes dryer, etc.
It is the responsibility of the home owner to service and maintain the appliance. If any claims are sent to FPI, you may be asked for service records to ensure the appliance has been
maintained. Retain all receipts for both service and/or parts which may have been replaced. Lack of service/maintenance is the largest contributor to malfunction of an appliance and
is not covered under the terms of this warranty.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
Regency® will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from Regency®, may nullify your warranty
on this product.
Malfunction/damage of this appliance due to mother nature (wind, rain, snow, floods, etc.) is not covered under the terms of this warranty policy. Some minor expansion, contraction,
or movement of certain parts and resulting noise, is normal and not a defect and therefore not covered under this Limited Warranty.
If the appliance has been operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals, it will not be covered under this Limited Warranty.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior/exterior facia is not the responsibility of Regency®.
* Subsidy according to job scale as predetermined by FPI.
P33CE-10 Direct Vent Gas Fireplace |
55
Register your Regency® warranty online
www.regency-fire.com
Reasons to register your product online today!
• View and modify a list of all your registered products.
• Request automatic email notification of new product updates.
• Stay informed about the current promotions, events, and
special offers on related products.
Installer: Please complete the following information
Panorama P33CE
Dealer Name & Address:_______________________________________________
___________________________________________________________________
Installer:____________________________________________________________
Phone #:____________________________________________________________
Date Installed:_______________________________________________________
Serial No.:___________________________________________________________ Regency and SureFire are trademarks of FPI Fireplace Products International Ltd.
© Copyright 2015, FPI Fireplace Products International Ltd. All rights reserved.
Printed in Canada