User manual Washer- dryer ZWD 12270 W1 ZWD

132963661.qxd
27/05/2008
11.47
Pagina
User
manual
Washerdryer
ZWD 12270 W1
ZWD 12270 S1
ZWD 14270 W1
ZWD 16270 W1
1
132963661.qxd
27/05/2008
11.47
Pagina
2
Thank you for selecting our appliance
We wish you lots of enjoyment with your new appliance and we hope that you will consider our
brand again when purchasing household appliances.
Please read this user manual carefully and keep it throughout the product life cycle as a reference
document. The user manual should be passed on to any future owner of the appliance.
The following symbols are used in this manual:
Important information concerning your personal safety and information on how to avoid
damaging the appliance.
General information and tips
Environmental information
Content
Safety information - - - - - - - - - - - - - - - - - - -3
Washing only - - - - - - - - - - - - - - - - - - - - -18
Description of the appliance - - - - - - - - - - - -5
Drying only - - - - - - - - - - - - - - - - - - - - - - -20
Detergent dispenser drawer - - - - - - - - - - - -5
Autodrying - - - - - - - - - - - - - - - - - - - - - - -21
Control panel and functions - - - - - - - - - - - -6
Care and cleaning - - - - - - - - - - - - - - - - - -22
Programme table - - - - - - - - - - - - - - - - - -10
What to do if... - - - - - - - - - - - - - - - - - - - - 25
Drying times - - - - - - - - - - - - - - - - - - - - - -12
Technical data- - - - - - - - - - - - - - - - - - - - - 29
Programme information - - - - - - - - - - - - - -13
Consumption values - - - - - - - - - - - - - - - - 30
Washing and drying hints - - - - - - - - - - - - -14
Installation instruction - - - - - - - - - - - - - - - 31
Before the first use - - - - - - - - - - - - - - - - -17
Environmental concerns - - - - - - - - - - - - - 35
Operating Sequence - - - - - - - - - - - - - - - -18
2
132963661.qxd
27/05/2008
11.47
Pagina
3
Safety information
In the interest of your safety and to ensure
the correct use, before installing and first
using the appliance, read this user manual
carefully, including its hints and warnings.
To avoid unnecessary mistakes and
accidents, it is important to ensure that all
people using the appliance are thoroughly
familiar with its operation and safety
features. Save these instructions and make
sure that they remain with the appliance if it
is moved or sold, so that everyone using it
through its life will be properly informed on
appliance use and safety.
General safety
●
●
●
●
●
●
●
It is dangerous to alter the specifications or
attempt to modify this product in any way.
During high temperature washing and drying
programmes the door glass may get hot. Do
not touch it!
Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp
material can cause extensive damage and
must not be placed into the machine.
Only use the advised quantities of fabric
softener and detergent. Damage to the fabric
can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
Wash small items such as socks, laces,
washable belts etc in a washing bag or
pillow case as it is possible for such items to
slip down between the tub and the inner
drum.
Do not use your washer-dryer to wash
articles with whalebones, material without
hems or torn material.
●
●
Always unplug the appliance and turn off the
water supply after use, cleaning and
maintenance.
Under no circumstances should you attempt
to repair the machine yourself. Repairs
carried out by inexperienced persons may
cause injury or serious malfunctioning.
Contact your local Service Centre. Always
insist on genuine spare parts.
Installation
●
●
●
●
●
●
●
●
●
This appliance is heavy. Care should be
taken when moving it.
When unpacking the appliance, check that it
is not damaged. If in doubt, do not use it and
contact the Service Centre.
All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this is
not adhered to. See relevant section in the
user manual.
After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable.
If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to
circulate freely under the appliance.
Always be sure, that there is no water
leakage from hoses and their connections
after the installation.
If the appliance is installed in a location
subject to frost, please read the «dangers of
freezing» chapter.
Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
3
132963661.qxd
27/05/2008
11.47
Pagina
Use
●
●
●
●
●
●
●
●
●
●
4
This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
Only wash and dry fabrics which are
designed to be machine washed and dried.
Follow the instructions on each garment
label.
Do not overload the appliance. See the
relevant section in the user manual.
Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and
treat stains such as paint, ink, rust, and
grass before washing. Underwired bras must
NOT be machine washed.
Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
As some duvets and eiderdowns should be
washed/dried in large commercial machines
because of their bulk, please check with the
manufacturer of the item before washing in a
domestic machine.
The users should always check that they
have not left their gas lighters (disposable or
otherwise) in their clothing.
Never dry items that have had contact with
chemicals such as dry cleaning fluid.These
are of a volatile nature and could cause an
explosion.
Only tumble dry items which have been
washed in water or require airing.
Plastic detergent dispensers should not
remain in the drum during the drying cycle,
as the plastic used is not designed to
withstand the heat. If you wish to washthrough-to-dry you should use the
conventional detergent dispenser drawer.
4
●
●
Never pull the power supply cable to remove
the plug from the socket; always take hold of
the plug itself.
Never use the washer-dryer if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the washer-dryer is accessible.
Child safety
●
●
●
●
●
This appliance is not intended for use by
persons (including children) with reduced
physical sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Young children should be supervised to
ensure that they do not play with the
appliance.
The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children danger of suffocation! Keep them out of
children’s reach
Keep all detergents in a safe place out of
children’s reach.
Make sure that children or pets do not climb
into the drum. To avoid that they remain
closed inside the drum, the machine
incorporates special feature.
To activate this device,
rotate the button
(without pressing it)
inside the door
clockwise until the
groove is horizontal. If
necessary use a coin.
To disable this device
and restore the
possibility of closing the
door, rotate the button
anti-clockwise until the
groove is vertical.
132963661.qxd
27/05/2008
11.47
Pagina
5
Description of the appliance
1
Detergent dispenser drawer
2
Control panel
3
Door opening handle
4
Drain pump
5
Adjustable feet
1
2
3
4
5
Detergent dispenser drawer
Prewash
Wash
Fabric Softener
5
132963661.qxd
27/05/2008
11.47
Pagina
6
Control panel and functions
1
2
3
4
5
6
7
8
Control Panel key symbols:
= «No spin» option,
= «Rinse Hold» option,
= Child safety lock
Information
The control panel is illustrated above. It shows the programme selector dial as well as the different
buttons, the pilot lights and the display. These are represented by relevant numbers which are
explained in the table below.
1
Programme selector dial and
On/Off switch
●
●
2 Spin reduction button
6
Press the Spin button repeatedly to change the spin
speed, if you want your laundry to be spun at a speed
different from the one proposed by the washer-dryer or to
select the «No spin» or the «Rinse Hold» option. The
relevant light will light up.
By pressing this button, you can select only one of the
following options: «Prewash», «Intensive», «Super
Quick» (see the relevant chapter «Functions»).
● The relevant light will light up.
●
3 Options button
The programme selector dial allows you to select a
programme and/or to switch the machine on/off. It can
be turned either clockwise or anticlockwise. The light of
button 6 starts to flash.
132963661.qxd
27/05/2008
11.47
4 Extra Rinse button
Pagina
●
●
5
Display
7
By pressing this button, the machine performs some
additional rinses.
The display shows the following information: duration of
the selected programme, selected drying time, incorrect
option selection, alarm codes, heating phase, child
safety lock and end of programme.
This button allows you to start the selected programme;
the corresponding green pilot light stops flashing.
● This button also interrupts a programme which is running,
the corresponding green pilot light starts to flash.
●
6 Start/Pause button
7 Drying Time button
●
●
8 Programme progress display
By pressing this button you can select a timed
programme for cotton or synthetics, the relevant phase
light illuminates.
The different pilot lights illuminate during the different
phases: washing (Wash= 8.1 ), drying (Dry= 8.2 ) and at
the end of the cycle (End= 8.3 ).
7
132963661.qxd
27/05/2008
11.47
Pagina
8
Display
2.05
5.3 5.2
The display ( 5 ) shows the following
information:
5.1 Duration of the selected programme/
After selecting a programme the duration of
the selected programme appears on the display (e.g. 2.05). During the programme, the
time remaining is updated every minute.
After having pressed button 6 , the light 8.1
illuminates and stays on.
/Selected drying time
After selecting a drying programme, the drying
time is displayed in minutes or in hours and
minutes (max 250 mins = 4.10 only for cottons).
After the programme has started the time
remaining is updated every minute.
/Incorrect option selection
The incorrect option selection is indicated by
the message Err displayed for a few seconds
and by flashing of the red light button 6 .
/Alarm codes
In the event of operating problems, some
alarm codes can be displayed, (see paragraph
«What to do if...»).
8
5.1
/End of programme
The End of programme is indicated by three
flashing zeros «0.00». The light 8.3 illuminates. After a few minutes the door can be opened.
5.2 Child safety lock
This device permits you to leave the appliance
unattended during it’s functioning.
5.3 Heating phase
During the washing cycle the display shows a
temperature icon to indicate that the appliance
has started the heating phase of the water in
the tub.
«Stand by»
If your laundry is not removed during 10
minutes after the programme is finished, the
backlight of the display switches off and the
energy saving system will be enabled.
Only the button 6 pilot light is blinking to
indicate that the appliance has to be switched
off.
By pressing any button the appliance will come
out from the energy saving status and you
could set another washing programme or
switched off the appliance.
132963661.qxd
27/05/2008
11.47
Pagina
Functions
No spin (button 2 )
By selecting this option all the spinning phases
are suppressed to prevent the fabrics from
creasing. The final spin is replaced by a
draining phase.
Rinse Hold (button 2 )
By selecting this option the water of the last
rinse is not emptied out to prevent the fabrics
from creasing.
When the programme has finished, the
Start/Pause and the «Wash» light go off, the
«End»( 8.3 ) pilot light illuminates, the display
shows three flashing zeros «0.00» and the
door is blocked to indicate that the water must
be emptied out.
To empty out the water see chapter «At the
end of the programme».
Prewash (button 3 )
Select this option if you wish your laundry to be
prewashed at 30°C before the main wash (not
available for all programmes). The prewash
ends with a short spin in programmes for
cotton and synthetics, whereas in the
programmes for delicate fabrics the water is
only drained.
Intensive (button 3 )
This option can be selected for heavily soiled
laundry: the washing intensity will be increased
and the washing time will be prolonged by a
few minutes depending on the selected type of
fabric.
9
Extra Rinse option (button 4 )
This option is recommended for people who
are allergic to detergents, and in areas where
the water is very soft. The machine performs
some additional rinses.
For the options compatibility with each
programme, please refer to the «Programme
table».
Drying time (button 7 )
By pressing this button you can select a timed
drying for cotton or synthetics. The
corresponding light 8.2 illuminates. The
selected drying time appears on the display.
For Cottons you can select a drying time from
10 minutes to 250 minutes (4.10).
For Synthetics it is possible to select a drying
time from 10 minutes to 130 minutes (2.10).
Every time you press the button the time
increases by 5 mins.
Pilot Light (s) 8
When selecting the programmes, depending on
the programme selected, the «Wash» ( 8.1 ) or
the «Dry» ( 8.2 ) pilot light illuminates
and stays on while the machine is working. In
any case both lights indicate that the appliance
starts operating and the door is locked.
When the programme has finished, the «End»
( 8.3 ) pilot light illuminates and the other lights
go off.
Super Quick (button 3 )
A very short cycle for slightly soiled items that
have been used or worn for a short time. The
washing time will be reduced according to the
type of fabric and the selected temperature.
We recommend that you reduce the load size.
9
132963661.qxd
27/05/2008
11.47
Pagina
10
Programme table
Programme/
Temperature
Type of laundry
Options
Spin red.
Prewash, Intensive,
Super Quick(*),
Extra rinse
Description of
programme
Main wash, rinses
Long spin at max speed
Max Load: 6 Kg
Reduced Load: 3 Kg
Cottons
90°
White cotton
(normally soiled cotton
items
Cottons
60° Eco
White and fast
coloured cotton
(normally soiled cotton
items)
Cottons
60° - 40°
Coloured cotton
normally soiled
Spin red.
Prewash, Intensive,
Super Quick(*),
Extra rinse
Main wash, rinses
Long spin at max speed
Max Load: 6 Kg
Reduced Load: 3 Kg
Cottons
40° Eco
Coloured cotton lightly
soiled
Spin red.
Prewash, Extra rinse
Main wash, rinses
Long spin at max speed
Max Load: 6 Kg
Synthetics
50° - 40
Synthetic or mixed
fabrics
Spin red.
Prewash, Intensive,
Super Quick(*),
Extra rinse
Main wash, rinses
Short spin at 900 rpm
Max Load: 3 Kg
Reduced Load:1.5 Kg
Synthetics
Easy iron 40°
Synthetic or mixed
fabrics to be gently
washed and spun.
Spin red.
Prewash, Extra rinse
Main wash, rinses
Short spin at 900 rpm
Max Load: 1.5 Kg
Delicates
40° - 30°
Delicate fabrics, for
example curtains.
Spin red.
Prewash, Extra rinse
Main wash, rinses
Long spin at max speed
Max Load: 6 Kg
Main wash, rinses
Short spin at 700 rpm
Prewash, Super Quick(*) Max Load: 3 Kg
Intensive, Extra Rinse Reduced Load:1.5 Kg
(*) If you select the option «Super Quick» by pressing the button 3 , we recommend that you
reduce the load sizes as indicated in the table above. Full loading is possible however with
somewhat reduced cleaning results.
10
132963661.qxd
27/05/2008
11.47
Pagina
11
Programme table
Programme/
Temperature
Type of laundry
Wool
40°
Programme for wool
«Pure new wool, nonshrink, machine
washable» label.
Handwash
30° - Cold
Special programme for
hand washing fabrics
Mini 30’
30°
Short cycle for lightly
soiled fabrics
Silk
30°
Silk items to be gently
washed and spun.
Rinse
Separate rinse cycle for
hand washed cotton
items.
Drain
For emptying out the last
rinse water in
programmes with the
«Rinse Hold» option.
Spin
Separate spin for
cottons.
Options
Spin red.,
Spin red.,
Description of
programme
,
Main wash, rinses
Short spin at 900 rpm
Max Load: 2 Kg
,
Main wash, rinses
Short spin at 900 rpm
Max Load: 2 Kg
Main Wash, rinses
Short spin at 700 rpm
Max Load: 2.5 Kg
,
Spin red.
Extra rinse
Main wash, rinses
Short spin at 700 rpm
Max Load: 1 Kg
3 rinses
Long spin at max speed
Max Load: 6 Kg
Draining of water
Spin red.
Drain and long spin
11
132963661.qxd
27/05/2008
11.47
Pagina
12
Drying Times
Degree of drying
Suitable for
items to put
away without
ironing
Type of fabric
Cotton and linen
(bathrobes, bath towels,
etc
Max Load
Spin speed
Suggested
drying time
(mins)
4 kg
1600 rpm
1400 rpm
1200 rpm
130 - 150
140 - 160
150 - 170
1600 rpm
75 - 85
1400 rpm
80 - 90
1200 rpm
85 - 95
1600 rpm
35 - 45
1400 rpm
40 - 50
1200 rpm
45 - 55
2 kg
900 rpm
70 - 80
1 kg
900 rpm
35 - 45
1600 rpm
1400 rpm
1200 rpm
1600 rpm
1400 rpm
1200 rpm
1600 rpm
1400 rpm
1200 rpm
100 - 120
110 - 130
120 - 140
60 - 70
65 - 75
70 - 80
30 - 40
35 - 45
40 - 50
3 kg
1.5 kg
Synthetics and mixed fabrics (jumpers, blouses,
underwear, household
linen)
4 kg
Suitable
for ironing
Cotton and linen (sheets,
tablecloths, shirts, etc.)
3 kg
1.5 kg
In compliance with EC directive EN 50229 the cotton reference programme for the data
entered in the Energy Label must be tested dividing the maximum washing load by two equal
parts and drying with TIMED DRYING each of them.
NOTE!
The different type of cottons (towelling,sheets, shirts and so on) or eventual laundry rolling up
during spinning phase may cause a not uniform dryness. So, in the exceptional case that at the
end of the cycle the laundry remains slightly wet, we suggest you to stretch the items rolled up
out, to redistribute evenly the laundry in the drum and to select an additional drying cycle of 2030 minutes.
12
132963661.qxd
27/05/2008
11.47
Pagina
13
Programme information
Eco programmes
Wool and
Handwash
This programme can be selected for slightly or normally soiled
cotton items. The temperature will decrease and the washing time
will be extended. This allows you to obtain a good washing
efficiency whilst saving energy.
Washing programme for machine washable wool as well as for hand
washable woollens and delicate fabrics with the «hand washing»
care symbol
.
Silk
Delicate washing programme suitable for silk and mixed synthetics
items. Washing temperature is 30°C.
The maximum spin speed is automatically reduced to 700 rpm.
Easy Iron
Selecting this programme, the laundry is gently washed and spun to
avoid any creasing. In this way ironing is easier. Furthermore the
machine will perform additional rinses.
Mini 30’
Special program at 30°C, (the duration is approx. 30 minutes),
suitable for laundry to be freshened up: e.g. a sport jacket worn only
once or slightly soiled or new garments.
Rinses
With this programme it is possible to rinse and spin cotton garments
which have been washed by hand.
The machine performs 3 rinses, followed by a final spin at maximum
speed.
The spin speed can be reduced by depressing the button 2 .
Drain
For emptying out the water of the last rinse in programmes with the
Rinse Hold option.
Turn first the programme selector dial to «Off», then select
programme Drain and depress the button 6 .
Spin
Separate spin for hand washed garments and after programmes
with Rinse Hold option. Before selecting this programme the
selector dial must be turned to Off. You can choose the speed by
means of the relevant button to adapt it to the fabrics to be spun.
Off = Cancelling/
Switching off of the
appliance
To reset a programme and to switch off the machine turn the
selector dial to «Off». A new programme can now be selected.
13
132963661.qxd
27/05/2008
11.47
Pagina
14
Washing and drying hints
Sorting the laundry
Follow the wash code symbols on each
garment label and the manufacturer’s washing
instructions. Sort the laundry as follows: whites,
coloureds, synthetics, delicates, woollens.
Temperatures
90° or 95°
for normally soiled white cottons
and linen (e.g. tea cloths, towels,
tablecloths, sheets...)
50°/60°
for normally soiled, colour fast
garments (e.g. shirts, night
dresses, pyjamas....) in linen,
cotton or synthetic fibres and for
lightly soiled white cotton (e.g.
underwear).
30°-40°-Cold
for delicate items (e.g. net
curtains), mixed laundry including
synthetic fibres and woollens
bearing the label «pure new wool,
machine washable, non-shrink».
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Make sure that no metal objects are left in
the laundry (e.g. hair clips, safety pins,
pins). Button up pillowcases, close zip
fasteners, hooks and poppers. Tie any belts
or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
14
Avoid drying dark clothes with light coloured
fluffy items such as towels as these can attract
the fluff.
Remove the laundry when the appliance has
finished drying.
To avoid a static charge when drying is completed, use either a fabric softener when you
are washing the laundry or a fabric conditioner
specifically for tumble dryers.
Particularly delicate items such as synthetic
curtains, woollen and silk, garments with metal
inserts, nylon stockings, bulky garments such
as anoraks, bedcovers, quilts, sleeping bags
and duvets must not be machine dried.
Garments padded with foam-rubber or materials similar to foam-rubber must not be machine
dried; they represent a fire hazard.
Also, fabrics containing residues of setting
lotions or hair sprays, nail solvents or similar
solutions must not be machine dried in order to
avoid the formation of harmful vapours.
For drying, follow the indications given on the
manufacturer’s labels.
May be tumble dried
Drying at high temperature
Drying at reduced temperature
Do not tumble dry
IMPORTANT!
As a dryer, the machine works on the
condensation principle.
Therefore, the water tap must be open and
the drain hose must drain water into a sink
or into the drain pipe, even during the drying cycle.
132963661.qxd
27/05/2008
11.47
Pagina
Maximum loads
Recommended loads are indicated in the
programme charts.
General rules:
Cotton, linen: drum full but not too tightly
packed;
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no more
than one third full.
Washing a maximum load makes the most
efficient use of water and energy.
For heavily soiled laundry, reduce the load
size.
Laundry weights
The following weights are indicative:
bathrobe
napkin
quilt cover
sheet
pillow case
tablecloth
towelling towel
tea cloth
night dress
ladies’ briefs
man’s work shirt
man’s shirt
man’s pyjamas
blouse
men’s underpants
1200 g
100 g
700 g
500 g
200 g
250 g
200 g
100 g
200 g
100 g
600 g
200 g
500 g
100 g
100 g
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
15
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will have already been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone (*), lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Remove
any residual marks from white fabrics with
bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
(*) do not use acetone on artificial silk.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment. Although biodegradable,
detergents contain substances which, in large
quantities, can upset the delicate balance of
nature.
15
132963661.qxd
27/05/2008
11.47
Pagina
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washer-dryer
detergents may be used in this appliance:
● powder detergents for all types of fabric,
● powder detergents for delicate fabrics (60°C
max) and woollens,
● liquid detergents, preferably for low
temperature wash programmes (60°C max)
for all types of fabric, or special for woollens
only.
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash
programme.
If using concentrated powder or liquid
detergents, a programme without prewash
must be selected.
The washer-dryer incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
just before starting
the programme.
Any fabric softener or starching additives must
be poured into the compartment marked
before starting the wash programme.
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the
detergent dispenser drawer.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of
soiling and hardness of the water used.
Water hardness is classified in so-called
«degrees» of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company.
16
16
Follow the product manufacturers’ instructions
on quantities to use.
Degrees of water hardness
Follow the product manufacturers’ instructions
on quantities to use.
Use less detergent if:
● you are washing a small load,
● the laundry is lightly soiled,
● large amounts of foam form during washing.
Degrees
Level
Characteristic
German
°dH
French
°T.H.
1
soft
0-7
0-15
2
medium
8-14
16-25
3
hard
15-21
26-37
4
very hard
> 21
> 37
132963661.qxd
27/05/2008
11.47
Pagina
17
Before the first use
WARNING!
Ensure that the electrical and water
connections comply with the installation
instructions.
IMPORTANT!
Remove the polystyrene block and any
material from the drum.
IMPORTANT!
Pour 2 litres of water into the main wash
compartment
of the detergent drawer in
order to activate the ECO valve. Then run a
cotton cycle at 90°C or 95°C, without any
laundry in the machine, to remove any
manufacturing residue from the drum and tub.
Pour 1/2 a measure of detergent into the
dispenser drawer and start the machine.
Acoustic signals
The machine is supplied with an acoustic
device, which sounds in the following cases:
● at the end of the cycle
● in the event of operating problems
By pressing the buttons 2 and 3
simultaneously for about 6 seconds, the
acoustic signal is deactivated (except for the
events of operating problems).
By pressing these 2 buttons again, the acoustic
signal is reactivated.
Child safety lock
This device permits you to leave the appliance
unattended without having the worry that
children might be injured by or cause damage
to the appliance.
This function remains enabled also when the
washer-dryer is not working.
There are two different ways to set this option:
● before pressing the 6 : it will be impossible
to start the machine.
● after pressing the button 6 it will be
impossible to change any other programme
or option.
To enable (disable) this option press
simultaneously for about 6 seconds buttons 3
and 4 until the icon
appears
(disappears) on (from) the display.
17
132963661.qxd
27/05/2008
11.47
Pagina
18
Operating sequence - Washing only
Washing
possible. Close the door.
1. Load the laundry
Open the door by
carefully pulling the
door handle outwards.
Place the laundry in
the drum, one item at
a time, shaking them
out as much as
Measure out the detergent and the fabric
softener
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required,
pour it into the main wash compartment
and, if you wish to carry out the prewash phase,
pour it into the compartment marked
.
If required, pour fabric softener into the
compartment marked
(the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
Select the required programme by turning
the programme selector dial ( 1 )
Turn the programme selector dial to the
required programme. The green light of button
6 starts to flash.
On position «Off» the programme is reset and
the machine is switched off.
18
At the end of the programme the selector
dial must be turned to position «Off», to
switch the machine off.
IMPORTANT!
If you turn the programme selector dial to
another programme when the machine is
working, the red light of button 6 will flash 3
times and the message Err is displayed to
indicate a wrong selection. The machine will
not perform the new selected programme.
Select the spin speed or No Spin or Rinse
Hold option by pressing button 2
When selecting a programme, the light
corresponding to the maximum speed allowed
for that programme will illuminate (refer to the
section «Programme table» for the maximum
allowed by each cycle spin speed). The
relevant light will light up.
Select the desired option by pressing the
buttons 3 and 4
Depending on the programme, different
functions can be combined. These must be
selected after choosing the desired programme
and before pressing the button 6 . The
relevant light will light up.
In any case, if an option is chosen that is not
allowed with the selected programme, the
message Err will be displayed on the display
for a few seconds, and the red light of the
button 6 start flashing.
IMPORTANT!
For the compatibility of the options with the
washing programmes, please refer to the
«Programme table».
132963661.qxd
27/05/2008
11.47
Pagina
Start the programme by pressing button 6
To start the selected programme, press this
button; the corresponding green pilot light
stops flashing. The appliance starts operating
and the door is locked.
To interrupt a programme which is running,
depress the button 6 : the corresponding
green pilot light starts to flash.
To restart the programme from the point at
which it was interrupted, press the same button
again.
IMPORTANT!
If an incorrect option is selected, the red pilot
light of the button 6 flashes 3 times and the
message Err is displayed for a few seconds.
Altering an option or a running programme
It is possible to change some options before
the programme carries it out.
Before you make any change, you must pause
the washer-dryer by pressing the button 6 .
Changing a running programme is possible
only by resetting it. Turn the programme
selector dial to «Off» and then to the new
programme position.
Start the new programme by depressing the
button 6 again. The washing water in the tub
will not be emptied out.
19
Opening the door after the programme has
started
First set the machine to pause by pressing the
button 6 . The door can be opened
immediately or after a few minutes depending
on the model. In any case do not try to open
the door if it is locked!
If the door remains locked, this means that the
machine is already heating or that the water
level is to high.
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to «Off». After a few
minutes the door can be opened (pay attention
to the water level and temperature!).
After this procedure, it will be necessary to set
the programme and the options again and then
to press button 6 .
At the end of the programme
The machine stops automatically. Some
acoustic signals sound. The light of button 6
and the light 8.1 go off, the light 8.3
illuminates and on the display will appear a
flashing «0.00». The door can be opened.
If, at the end of a programme, there is water in
the tub, the light 8.3 illuminates but the door
remains locked to indicate that the water must
be emptied out before opening the door.
Interrupting a programme
Press the button 6 to interrupt a programme
which is running, the corresponding light starts
to flash. Press the same button again to restart
the programme.
Cancelling a programme
Turn the selector dial to «Off» to cancel a
programme which is running. You can now
select a new programme.
19
132963661.qxd
27/05/2008
11.47
Pagina
To empty out the water proceed as follows:
1. turn the programme selector dial to «Off»
2. select the Drain or Spin programme
3. reduce the spin speed if needed, by pressing
the relevant button
4. press the button 6
5. at the end of programme, only the pilot light
8.3 illuminates.
20
Turn the programme selector dial to «Off» to
switch the machine off.
Remove the laundry from the drum and
carefully check that the drum is empty.
If you do not intend to carry out another wash,
close the water tap.
Leave the door open to prevent the formation
of mildew and unpleasant smells.
Operating sequence - Drying only
The recommended load to dry in your washerdryer is 3 kg for cotton and 2 kg for synthetics.
Note!
It is possible also to dry up to 4 kg of cotton items (see the drying times table).
The water tap must be open and the drain
hose must be positioned in the sink or connected to the drain pipe.
1. Load the laundry.
2. Turn the selector dial to «Cottons» or
«Synthetics» programme in the «Drying»
section.
3. Select the duration of the drying cycle by
pressing repeatedly button 7 until the
time you want appears on the display (see
the drying programmes).
For Cottons you can select a drying time from
10 minutes to 250 minutes (4.10).
For Synthetics you can select a drying time
from 10 minutes to 130 minutes (2.10).
Every time you press the button the time
increases by 5 mins.
20
Note!
The drying time will automatically increase by
up to 2 minutes. This is quite normal.
4. Press the button 6 to start the programme. After the programme has started,
the time remaining is updated every
minute.
5. At the end of the programme, the buzzer
sounds. Three flashing zeros «0.00» will
appear on the display.
At this point, begins an «anti-crease
phase», which lasts about 10 minutes. The
door is locked and can be opened only at
the end of this phase.
Note!
If you wish to open the door before the
anti-crease phase or to interrupt it, press
any key or turn the programme selector
dial to any programme position (except
«Off»). The door can be opened immediately or in a few minutes depending on the
model.
6. Turn the selector dial to the «Off» position
to switch the machine off. Remove the
laundry.
132963661.qxd
27/05/2008
11.47
Pagina
21
Autodrying (NON-STOP programme)
For NON-STOP programmes, the
recommended load to wash and dry in your
washer-dryer is 3 kg for cotton and 2 kg for
synthetics.
Note!
It is possible also to wash and dry up to 4
kg of cotton items (see the drying times
table).
Do not use a dosing device/ball when carrying
out a washing & drying programme.
1. Load the laundry.
2. Add detergent and fabric softener.
3. Switch the machine on by turning the
selector dial to the selected wash programme/fabric.
4. Select the drying time (see the
drying programmes).
5. Select the required options by pressing the
relevant buttons. The display shows the
entire duration of the washing and the
selected drying cycle.
If possible, do not select a spin speed
lower than that proposed by the appliance
to avoid a too long drying time so saving
energy.
In any case the reduction of the spin speed
is only possible after selecting drying.
The lowest values you can select are the
following:
- 900 r.p.m. for cottons
- 700 r.p.m. for synthetics
6. Start the programme by pressing the button
6 . After the programme has started, the
time remaining on the display is updated
every minute.
7. At the end of the programme the buzzer
sounds. Three flashing zeros «0.00»
appear on the display .
At this point of the programme, starts an
anti-crease phase which lasts about 10
minutes. During this time the door is locked
and the display keeps showing the flashing
zeros «0.00».
(If you wish to open the door before or during the anti-crease phase, please follow the
instructions given in the previous chapter).
7. Turn the selector dial to the «Off» position
to switch the machine off.
8. Remove the laundry.
21
132963661.qxd
27/05/2008
11.47
Pagina
22
Care and cleaning
IMPORTANT!
You must DISCONNECT the appliance from
the electricity supply, before you can carry out
any cleaning or maintenance work.
Descaling
The water we use normally contains lime. It is
a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder
manufacturer's instructions. This will help to
prevent the formation of lime deposits.
Maintenance Wash
With the use of low temperature washes it is
possible to get a build up of residues inside the
drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
● The drum should be empty of laundry.
● Select the hottest cotton wash programme.
● Use a normal measure of detergent, must be
a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
To aid cleaning, the top part of the additive
compartment should be removed.
Remove the drawer by pressing the catch
downwards and by pulling it out. Flush it out
under a tap, to remove any traces of
accumulated powder.
Cleaning the drawer recess
Having removed the
drawer, use a small
brush to clean the
recess, ensuring that
all washing powder
residue is removed
from the upper and
lower
part of the recess.
Replace the drawer and run the rinse
programme without any clothes in the drum.
Cleaning the pump
The pump should be inspected if
• the machine does not empty and/or spin
• the machine makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump.
Proceed as follows:
• disconnect the appliance.
• if the appliance is operating, wait, if
necessary, until the water has cooled down.
• open the pump door levering on the groove
with a coin.
• place a bowl with a small edge close to the
pump to collect any spillage
1
2
22
132963661.qxd
27/05/2008
11.47
Pagina
23
Care and cleaning
• pull out the emergency emptying cap from the
filter cover, using a pliers.
• when no more water comes out, unscrew the
pump cover, using a pliers, and remove the
filter. Always keep a rag nearby to dry up
spillage of water when removing the cover.
2
1
• Remove any objects from the pump impeller
by rotating it.
• replace the emergency emptying cap into the
filter cover and fix it firmly.
IMPORTANT!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When
replacing the cover, ensure it is securely
retightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filter
If your water is very hard or contains traces of
lime deposit, the water inlet filter may become
clogged.
It is therefore a good idea to clean it from time
to time.
Turn off the water tap.
Unscrew the water
inlet hose. Clean the
filter using a hard
bristle brush. Tighten
up the inlet hose.
The dangers of freezing
If the machine is exposed to temperatures
below 0°C, certain precautions should be
taken:
• pull out the plug from the power socket;
• Close the pump
door.
23
132963661.qxd
27/05/2008
11.47
Pagina
24
Care and cleaning
• turn off the water tap.
• unscrew the inlet hose.
• place a bowl with a small edge close to the
pump to collect any spillage from the
emergency emptying hose.
Place the end of the inlet hose in a bowl
placed on the floor and let water drain out.
• screw the water inlet hose back on and
reposition the emergency emptying cap on
again into the filter cover.
• when you intend to start the machine up
again, make sure that the room temperature
is above 0°C.
IMPORTANT!
Every time you drain the water through the
emergency emptying hose you must pour 2
litres of water into the main wash compartment
of the detergent drawer and then run the drain
programme. This will activate the ECO VALVE
device avoiding that part of the detergent
remains unused at next washing.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled
down;
• open the pump door using a suitable tool;
24
• place a bowl with a small edge close to the
pump to collect any spillage. Remove the
emergency emptying cap from the filter
cover. The water should drain by gravity into
the bowl. When the bowl is full, put the cap
back on filter cover. Empty the bowl. Repeat
the procedure until water stops flowing out;
• clean the pump if necessary as previously
described;
• replace the filter into the pump and screw it
firmly as previously described;
• replace the emergency emptying cap into the
filter cover and close the pump door.
132963661.qxd
27/05/2008
11.47
Pagina
25
What to do if...
IMPORTANT!
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily
without calling out an engineer. Before contacting your local Service Centre, please carry out the
checks listed below.
During machine operation it is possible that the red pilot light of the button 6 flashes, the buzzer
sounds and one of the following alarm codes appears on the display to indicate that the machine
is not working.
● E10: problem with the water supply
● E20: problem with water draining
● E40: door open.
Once the problem has been eliminated, press the button 6 to restart the programme. If after all
checks, the problem persists, contact your local Service Centre.
Malfunction
Possible Cause / Solution
The washer-dryer does not start:
The door has not been closed. E40
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse or the fuse in the plug has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the
button 6 has not been pressed.
• Please turn the selector dial and press the button
6 again.
The «Child Safety Lock» option has been selected.
• Disable the «Child Safety Lock» option.
The machine does not fill:
The water tap is closed. E10
• Open the water tap.
The inlet hose is squashed or kinked. E10
• Check the inlet hose connection.
The filter in the inlet hose is blocked. E10
• Clean the water inlet hose filter.
The door is not properly closed. E40
• Close the door firmly.
25
132963661.qxd
27/05/2008
11.47
Pagina
Malfunction
The machine fills then empties
immediately:
The machine does not empty and/or
does not spin:
26
Possible Cause / Solution
The end of the drain hose is too low.
• Refer to relevant paragraph in «water drainage»
section.
The drain hose is squashed or kinked. E20
• Check the drain hose connection.
The drain pump is clogged. E20
• Clean the drain pump.
The Rinse Hild or No spin option has been selected.
• Select the Drain or Spin programmes
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Too much detergent or unsuitable detergent (creates
too much foam) has been used.
• Reduce the detergent quantity or use another one.
There is water on the floor:
Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose; check to see if it is
damp.
• Check the water inlet hose connection.
The inlet hose is damaged.
• Replace it with a new one.
The emergency emptying cap has not been replaced
on the filter after cleaning.
• Refit the emergency emptying cap on the filter.
Unsatisfactory washing results:
26
Too little detergent or unsuitable detergent has been
used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to
washing.
• Use commercial products to treat the stubborn
stains.
The correct temperature was not selected.
• Check if you have selected the correct
temperature.
Excessive laundry load.
• Reduce the laundry load.
132963661.qxd
27/05/2008
11.47
Pagina
Malfunction
The door will not open:
27
Possible Cause / Solution
The programme is still running.
• Wait until the end of washing cycle.
The door lock has not been released.
• Wait a few minutes.
There is water in the drum.
• Select drain or spin programme to empty out the
water.
The transit bolts and packing have not been
removed.
• Check the correct installation of the appliance.
The machine vibrates or is noisy:
The support feet have not been adjusted.
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is too little laundry in the drum.
• Load more laundry.
Spinning starts late or the machine
does not spin:
The electronic unbalance detection device has cut in
because the laundry is not evenly distributed in the
drum. The laundry is redistributed by reverse rotation
of the drum. This may happen several times before
the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not
evenly distributed in the drum, the machine will not
spin. In this case, redistribute the load manually and
select the spin programme.
● Redistribute the laundry.
The machine is fitted with a type of motor which
makes a different noise compared with other
traditional motors. This new motor ensures a softer
The machine makes an unusual noise
start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of
the machine.
27
132963661.qxd
27/05/2008
11.47
Pagina
Malfunction
28
Possible Cause / Solution
The machine does not dry or does not The drying time has not been selected.
dry properly
• Select the drying time.
The water tap is not turned on (E10)
• Open the water tap.
The drain filter is clogged (E20)
• Clean the drain filter.
The machine is overloaded.
• Reduce the laundry load.
The selected drying programme or time was not
suitable for the laundry.
• Select the suitable drying programme or time for the
laundry.
28
...
...
No.
..
Ser.
If you are unable to identify or solve the
problem, contact our service centre.
Before telephoning, make a note of the model,
serial number and purchase date of your
machine: the Service Centre will require this
information.
...
Machines based on modern technology operate very
economically using very little water without affecting
performance.
Mod.
Prod ...
. No. ... ...
...
...
No water is visible in the drum
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
132963661.qxd
27/05/2008
11.47
Pagina
29
Technical data
Dimensions
Width
60 cm
Height
85 cm
Depth (including the porthole)
63 cm
Electrical connection Voltage Overall power - Fuse
Information on the electrical connection is given on the rating
plate on the inner edge of the appliance door
Water supply pressure
Minimum
0,05 MPa
Maximum
0,8 MPa
Maximum Load
Cotton
Synthetics
Delicates
Woollens and handwash
6.0
3.0
3.0
2.0
Maximum Drying Load
Cotton
Cotton Big Capacity
Synthetics
Spin Speed
Maximum
kg
kg
kg
kg
3. 0 kg
4
kg
2
kg
1600 rpm (ZWD 16270 W1)
1400 rpm (ZWD 14270 W1)
1200 rpm (ZWD 12270 W1)
1200 rpm (ZWD 12270 S1)
29
132963661.qxd
27/05/2008
11.47
Pagina
30
Consumption values
Cottons 90°C
Cottons 60° Eco(*)
Cottons 60°C - 40°C
Cottons 40° Eco
Synthetics 50°C - 40°C
Synthetics Easy Iron 40°C
Delicates 40°C - 30°C
Wool 40°C
Programme
duration
(in minutes)
For the duration of the programmes,
please refer to the display on the
control panel
Programme
Energy
consumption
(in kWh)
Water
consumption
(in litres)
2.0
61
1.02
54
1.3
58
1.14
54
0.8
51
0.35
60
0.55
60
0.4
53
Information
The consumption data shown on this chart is to
be considered purely indicative, as it may vary
depending on the quantity and type of laundry,
on the inlet water temperature and on the
ambient temperature. It refers to the highest
temperature for each wash programme.
30
(*) The “Cottons 60° Eco” is the reference
programme with a load of 6 kg for the data
entered in the energy label, in compliance
with EEC 92/75 standards.
132963661.qxd
27/05/2008
11.47
Pagina
31
Installation instruction
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
draining hose from the hose holders on the
rear of the appliance.
A
C
B
C
B
3. With a suitable spanner unscrew and
remove the central rear bolt A.
4. Unscrew and remove the two large rear
bolts B and the six smaller bolts C.
E
C
D
5. Remove the bracket D, refit the six smaller
bolts C and slide out the relevant plastic
spacer E.
6. Open the porthole, take out the inlet hose
from the drum and remove the polystyrene
block fitted on the door seal.
7. Fill the smaller upper hole and the two large
ones with the corresponding plastic plug
caps supplied in the bag containing the
instruction booklet.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units. Level the washer-dryer by raising
or lowering the feet. The feet may be tight to
adjust as they incorporate a self locking nut,
but the machine MUST be level and stable.
If necessary, check the setting with a spirit
level.
Any necessary adjustment can be made with a
spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Never place cardboard, wood or similar
materials under the machine to compensate for
any unevenness in the floor.
C
31
132963661.qxd
27/05/2008
11.47
Pagina
32
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied with
the appliance. The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to
purchase a new, longer hose specially
designed for this type of use.
NOTE
Installation should
comply with local
water authority and
building
regulations’
requirements.
Special conditions
If the floor is carpeted or covered with crumbly
or soft material, insert a rigid support base
under the feet to prevent noise, vibration or
displacement. The base should protrude a few
centimetres beyond the edges of the machine.
WARNING!
The machine should NOT be placed on deep
pile carpeting.
NOTE
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of a breakdown.
32
45°
35°
Water inlet
An inlet hose is supplied and can been found
inside the machine drum.
Do not use the hose from your previous
machine to connect to the water supply.
1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled
connection to the machine.
Do not place the inlet hose downwards.
Angle the hose to the left or right depending
on the position of your water tap.
3.Set the hose
correctly by
loosening the ring
nut.
After positioning the
inlet hose, be sure to
tighten the ring nut
again to prevent
leaks.
The appliance must be connected to a cold
water supply.
A minimum water pressure of 0.05 MPa (0.5
bar) is required for safe operation of the
appliance.
If you cannot make the cold water connection
direct from the rising mains, you may be able
to operate the appliance from your cold water
storage system.
There should be a minimum vertical distance
of 5.02m (16.5 ft) between the appliance’s
inlet and the bottom of the water storage tank.
Water drainage
This appliance is designed to be permanently
plumbed into your home's drainage system
using one of the following methods.
1. Into a drainage standpipe.
Firstly form a hook in
the end of the drain
hose using the «U»
piece supplied.
“U” piece
supplied
132963661.qxd
27/05/2008
11.48
Pagina
33
Place the drain hose into your standpipe, which
should have an internal diameter of
approximately 38mm thus ensuring there is an
air break between the drain hose and
standpipe.
Loop
Sport 40°
Sport Shoes 40°
Off
Cottons
95°
3h
60° Eco
Silk
700
Wash
Prewash
Door
Intensive
40°
Synthetics
50°
End
Super
Quick
Options
Spin
Extra Rinse
Start/Pause
Easy Iron 40°
Spin
Drain
9h
900
40° Eco
40°
Wool
6h
1000
60°
Mini 30'
Cold
Hand
Wash
30°
Rinse
30°
40°
ZWF10070W
Delicates
38 mm (1.5”)
standpipe
diameter
30 cm (12")
Special
1000 6kg
When discharging into a standpipe ensure that
the top of the standpipe is no more than 90 cm
(35.4'') and no less than 60 cm (23.6'') above
floor level.
Sport 40°
Sport Shoes 40°
Off
Cottons
95°
60° Eco
Silk
60°
Mini 30'
40° Eco
Cold
Hand
Wash
30°
3h
40°
9h
900
700
Wash
Prewash
Door
Intensive
End
Super
Quick
Spin
Options
Extra Rinse
Start/Pause
Easy Iron 40°
Spin
Rinse
30°
40°
Delicates
ZWF10070W
Min. 60 cm (23.6”)
Drain
6h
1000
40°
Synthetics
50°
Wool
Max. 90 cm (35.4”)
Special
1000 6kg
The drain hose may be extended to a
maximum of 4 metres. An additional drain hose
and joining piece is available from your local
Service Force Centre. The joining piece must
have an internal diameter of 18mm.
If your drain hose
looks like this (see
below) you do not
require the «U» piece.
Just push the hose
firmly into the
standpipe.
Push the drain hose onto the spigot and secure
with a clip, ensure a loop is formed in the drain
hose (see diagram) to prevent waste from the
sink entering the washer-dryer.
Important!
Before connecting the machine to new
pipework or to pipework that has not been
used for some time, run off a reasonable
amount of water to flush out any debris that
may have collected in the pipes.
In the interest of the environment
Washer-dryers should be connected to the
FOUL drainage system, the water will then be
taken to a sewage works for treatment before
being discharged safely into a river. It is
essential that these appliances are not
connected to the surface water drainage
system as this water is discharged directly into
a river or stream and may cause pollution.
If you require any further advice please contact
your local water authority.
SHOWER
SINK
WASHING
MACHINE
2. Onto a sink outlet spigot.
If the outlet spigot has not been used before,
remove any blanking plug that may be in place.
TOILET
BATH
BIDET
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
UNTREATED
DISCHARGE
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
TREATED
DISCHARGE
RIVER
RIVER
33
132963661.qxd
27/05/2008
11.48
Pagina
34
Electrical connection
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp
must be secure over the outer sheath.
WARNING!
This appliance must be earthed.
The manufacturer declines any liability
should this safety measure not be
observed.
Before switching on, make sure the electricity
supply voltage is the same as that indicated
on the appliance’s rating plate.
IMPORTANT!
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
A cut off plug inserted into a 13 amp socket
is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely. Should the appliance power supply
cable need to be replaced, this must be
carried out by our Service Force Centre.
The power supply cable must be easily
accessible after installing the appliance.
The appliance is supplied with a 13amp plug
fitted. In the event of having to change the
fuse in the plug supplied, a 13amp ASTA
approved (BS1363/A) fuse must be used.
Should the plug need to be replaced for any
reason, proceed as described below.
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow ..............................- Earth
Blue ....................................................- Neutral
Brown..................................................- Live
GREEN & YELLOW
13 A
E
N
L
BROWN
BLUE
CORD CLAMP
The wire coloured
green and yellow must
be connected to the
terminal marked with
the letter «E» or by the
earth symbol
or
coloured green and yellow.
The wire coloured blue must be connected to
the terminal marked «N» or coloured black.
The wire coloured brown must be connected
to the terminal marked «L» or coloured red.
34
WARNING!
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole switch
between the appliance and the electricity
supply (mains), with a minimum gap of 3mm
between the switch contacts and of a type
suitable for the required load in compliance
with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
Fitting under a counter
WARNING!
Before any work to the appliance, you must
disconnect the plug from the power socket.
If the counter is too
low and it becomes
necessary to remove
the top lid of the
washer-dryer, a steel
plate, known as a
height reduction kit,
must be used.
Important!
For safety reasons, it is dangerous to fit the
appliance under a counter without the steel
plate, which you can order in your nearest
Service Force Centre.
132963661.qxd
27/05/2008
600
820
600
820
595
600
(see the picture above).
11.48
Pagina
35
The top must be fixed
to the cabinet as
follows: Unscrew the
screws from the back
panel of the
appliance. Push the
worktop to the back
and raise it to remove
Environmental concerns
Packaging materials
The materials marked with the symbol
recyclable.
>PE<=polyethylene
are
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by
disposing of them properly in appropriate
collection containers.
Old machine
Use authorised disposal sites for your old
appliance. Help to keep your country tidy!
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken over to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product.
For more detailed information about recycling
of this product, please contact your local
council, your household waste disposal service
or the shop where you purchased the product.
Ecological hints
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
● Normally soiled laundry may be washed
without prewashing in order to save
detergent, water and time (the environment
is protected too!).
● The machine works more economically if it is
fully loaded.
● With adequate pre-treatment, stains and
limited soiling can be removed; the laundry
can then be washed at a lower temperature.
● Measure out detergent according to the
water hardness, the degree of soiling and
the quantity of laundry being washed.
35
132963661.qxd
27/05/2008
11.48
Pagina
36
www.electrolux.com
www.zanussi-electrolux.co.uk
132963661-01-222008
Subject to change without notice