Owner’s Manual
AVDBR1
AUTOMOTIVE BLU-RAY PLAYER
For Sales Information Please Contact
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Warnings and Cautions
THE LIGHTNING FLASH AND ARROWHEAD
WITHIN THE TRIANGLE IS A WARNING SIGN
ALERTING YOU OF “DANGEROUS VOLTAGE”
INSIDE THE PRODUCT.
SEE MARKING ON BOTTOM OF PRODUCT
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. THE APPARATUS SHALL NOT BE
EXPOSED TO DRIPPING OR SPLASHING.
THE EXCLAMATION POINT WITHIN THE
TRIANGLE IS A WARNING SIGN ALERTING
YOU OF IMPORTANT INSTRUCTIONS
ACCOMPANYING THE PRODUCT.
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Caution
FCC Information
This product uses a laser. Use of controls or
adjustments or performance of procedures
other than those specified may result in
hazardous radiation exposure. Do not open
covers and do not repair the unit yourself.
Refer servicing to qualified personnel.
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Visible laser radiation when open. Avoid
exposure to beam.
Please respect the environment and
prevailing regulations.
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a mobile installation.
This equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
Before you dispose of batteries, ask your
dealer whether they are subject to special
recycling and if they will accept them for
disposal.
• Reorient or relocate the receiving
antenna
• Increase the separation between the
equipment and the receiver
Class 1 Laser Product
This unit must be opened only by qualified
technicians to prevent accidents caused by
the laser beam.
CLASS 1
LASER PRODUCT
This product
contains a low
power laser
device.
The marking plate is located on the bottom
enclosure of the apparatus.
X
-2-
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Warning and Cautions
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected
• Consult the dealer or an experienced
radio TV technician for help.
WARNING
This class B digital apparatus complies with
Canadian ICES-003.
Battery Precautions
Changes or modifications to this unit not
expressly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
Your remote control operates on batteries.
Please adhere to the following precautions:
Notice
An LCD panel and/or video monitor may be
installed in a motor vehicle and visible to the
driver if the LCD panel or video monitor is
used for vehicle information, system control,
rear or side observation or navigation. If
the LCD panel or video monitor is used for
television reception, video or Blu-ray/DVD
play, the LCD panel or video monitor must
be installed so that these features will only
function when the vehicle is in “park” or
when the vehicle’s parking brake is applied.
Notice
• If you are not using the remote control
for a long period of time, remove the
batteries.
• Do not mix different types of batteries or
new and old batteries.
• A battery may leak electrolyte if mixed
with a different battery type, if inserted
incorrectly, or if all batteries are not
replaced at the same time.
• Replace only with the type of batteries
specified.
• Do not use rechargeable batteries.
An LCD panel or video monitor used for
television reception, video or Blu-ray/
DVD play that operates when the vehicle
is in gear or when the parking brake is not
applied must be installed to the rear of the
driver’s seat where it will not be visible,
directly or indirectly, to the operator of the
motor vehicle.
• To avoid any risk of explosion, observe
the polarities indicated inside the battery
compartment.
• A battery may leak electrolyte or explode
if disposed of in fire or an attempt is made
to charge a battery not intended to be
recharged.
• Discard leaky batteries immediately.
Leaking batteries can cause skin burns or
other personal injury.
Service Information
Do not attempt to disassemble the unit.
This product does not contain customer
serviceable components. Refer all servicing
to qualified service personnel.
• When discarding batteries, be sure to
dispose of them in the proper manner,
according to your state/provincial and
local regulations.
Servicing is required when the apparatus
has been damaged in any way, such as the
power cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed
to rain or moisture, does not operate
normally, or has been dropped.
• Do not dispose of batteries in a fire or
recharge them. Batteries may explode or
leak.
• Do not expose batteries to excessive heat
from sunshine, fire or the like.
-3-
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Warnings and Cautions
Additional Precautions
• If your unit has been stored in a cool place
for any length of time, wait for about 2
hours before using it.
• Switching off the unit to standby
mode does not disconnect it from the
vehicle’s power. To completely isolate the
equipment, remove the plug from the
POWER connector as some components
remain connected to the electrical supply.
• If you notice any burning or smoke,
disconnect the unit immediately to avoid
any risk of electrocution.
• Do not expose the unit to dripping or
splashing.
• Care should be taken so that objects do
not fall into the unit.
• If an object or liquid enters inside the
unit, disconnect it immediately and have
it checked by an authorized servicer or
service center.
• The openings located on the unit are for
ventilation. Do not block any ventilation
openings.
• Always leave sufficient space around the
unit for ventilation. Do not place the unit
in a cabinet that may prevent air flow
through vent openings.
• Connect the DC Power Cable only to
a 12 V power source as marked on the
product.
• Protect the DC Power Cable from being
pinched.
• Avoid installing the unit in locations
where it would be subjected to dust, dirt
or excessive vibration.
• Use only with a bracket specified by the
manufacturer, or sold with the apparatus.
Cleaning
• Use a soft, dry, clean cloth.
• Using solvents, abrasive or alcohol-based
products risks damaging the unit.
Handling and Caring for Discs
• Handle your discs with care. Hold the disc
with your fingers at the edges or through
the hole.
• Always put discs back in their cases after
use and store in a vertical position.
• Do not play cracked, chipped or warped
discs.
• Do not try to repair discs with adhesive
tape or glue.
• Do not write on a disc.
• Do not scratch discs.
• Do not store discs in places exposed to
direct sunlight, high humidity or high
temperatures.
• Do not use aerosol cleaners, benzene,
anti-static liquids or any other solvent
for cleaning discs. When cleaning, wipe
gently with a soft damp (water only)
cloth. Always wipe from the center to the
edge. Avoid circular motions, which could
cause scratches and interference during
playback.
• Install in accordance with the instructions.
• Do not install the unit where it would
be subject to high temperatures, such
as from direct sunlight, from the vehicle
heater or from other apparatus (including
amplifiers) that produce heat.
-4-
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Table of Contents
Warnings and Cautions ................................................................................................. 2
Table of Contents ............................................................................................................ 5
Introduction .................................................................................................................... 6
Features ........................................................................................................................................................... 6
Accessories ...................................................................................................................... 6
Installation ...................................................................................................................... 7
Installing the Player ..................................................................................................................................... 7
Powering Your Blu-Ray Player .................................................................................................................. 8
Connecting the External Remote IR Receiver .................................................................................... 9
Connecting to Your Monitor..................................................................................................................... 10
Controls and Indicators .................................................................................................. 11
Remote Control Operation ............................................................................................ 12
Using the Remote Control......................................................................................................................... 12
Battery Replacement................................................................................................................................... 12
Playing a Blu-ray Disc or DVD ....................................................................................... 15
Basic Playback (Blu-Ray Disc or DVD) .................................................................................................... 15
Special Functions ......................................................................................................................................... 17
Playing an Audio CD ....................................................................................................... 19
Basic Playback (Audio CD) ......................................................................................................................... 19
Playing Picture Files ...................................................................................................... 20
Basic Playback (Picture Files) .................................................................................................................... 20
Viewing Files .................................................................................................................................................. 21
The Home (Setup) Menu ................................................................................................ 22
General Setting Menu................................................................................................................................. 22
Display Setting Menu.................................................................................................................................. 25
Audio Setting Menu .................................................................................................................................... 27
System Information ..................................................................................................................................... 27
Reference ........................................................................................................................ 28
Blu-Ray Region Codes ................................................................................................................................. 28
DVD Region Codes ....................................................................................................................................... 29
Compatible Formats.................................................................................................................................... 30
Specifications .................................................................................................................. 32
Troubleshooting ............................................................................................................. 33
Notes................................................................................................................................ 34
-5-
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Introduction
Thank you for choosing the AVDBR1 Blu-ray player. The AVDBR1 is designed to optimize the
enjoyment of your favorite Blu-ray/DVD discs in a mobile environment. This Blu-ray player is
designed to provide years of reliable, trouble-free service.
Please read this manual thoroughly prior to operating the Blu-ray player. Save this manual for
future reference.
Features
• Stand alone automotive Blu-ray player
• Slot Load
• Plays Blu-ray Discs (BD), DVD and CD discs
• One HDMI output
• Audio/Video output via RCA jacks
• WiFi capable to enable BD live features (adapter sold separately - future availability)
• Front panel controls
• USB input for thumb drives (up to 32 GB)
• Flexible mounting options
• IR remote control
• External Remote Infrared Receiver
Accessories
Please check and identify the included accessories:
Remote Control ................................................................................................................. x 1
AAA 1.5V Battery .............................................................................................................. x 2
RCA Audio/Video Cable ................................................................................................. x 1
DC Power Cable with 4-pin Power Connector ....................................................... x 1
External Remote IR Receiver ......................................................................................... x 1
Metal Mounting Brackets .............................................................................................. x 2
Black Pan Head Phillips Screw, M3 x 6 mm ............................................................. x 4
Rubber Foot.......................................................................................................................... x 4
Product Registration Card for Online Registration ............................................... x 1
-6-
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Installation
Before installing the player:
• Choose a mounting location where the
Blu-ray player does not get in the driver’s
way and cannot injure the passenger in
the event of an emergency stop.
• Connect the wiring temporarily. Make
sure it is connected correctly and the Bluray player and the system work properly.
Installing the Player
1. Install the Blu-ray player in a horizontal
position with the front end up at a
convenient angle, but not more than 30
degrees.
2. Screws are provided to attach the Bluray player to the (two) L-brackets. Fasten
the unit to the L-brackets by aligning
the screw holes on the L-brackets with
the screw holes on the unit. Refer to
following figure.
3. Tighten the screws on each side of the
Blu-Ray player.
Notes
4. Use self-tapping screws (not supplied)
to mount the L-brackets in the vehicle.
Be careful of hidden wiring under the
carpet.
• To ensure proper installation, use only
the parts included with the Blu-ray
player. The use of unauthorized parts
can cause malfunctions.
• Avoid installing the Blu-ray player
where it would be subject to high
temperatures, such as from direct
sunlight or from hot air from the
vehicle’s heater. Also avoid locations
where the player would be subjected to
dust, dirt or excessive vibration.
-7-
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Installation
AUDIO & VIDEO OUPUT
RCA JACK
3 PLACES
HDMI CONNECTOR
12 VDC INPUT
4 PIN POWER
CONNECTOR
IR SENSOR
INPUT JACK
Rear Panel
Powering Your Blu-ray Player
1. Connect the black wire (-) to the vehicle
ground.
2. Connect the red wire (+) to a switched
(Accessory) 12 VDC source.
3. Connect the 4-pin power connector to
the POWER jack on back of the player.
Fuse
housing
with 5A
fuse
Notes
• When connecting power and ground
in a mobile video installation ensure
that the ACC wire is fused at the point
where it is connected to the vehicle
ACC wiring. Failure to do so can result
in damage to the vehicle if a short
circuit develops between the vehicle
connection point and the mobile video
product.
Red (+) to
switched
12 VDC
Black (-) to
ground
-8-
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Installation
Connecting the External
Remote IR Receiver
1. Plug the 1/8” plug on the External
Remote IR Receiver cable into the IR EXT
jack on the back of the Blu-ray player.
2. Install the REMOTE SENSOR in a location
where the infrared beam will not be
blocked or interrupted.
REMOTE
External
Remote
IR Receiver
Remote
Sensor
-9-
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Installation
Connecting to Your Monitor
HDMI Jack
LINE OUTPUT Jacks (Audio and Video)
Video connections to a monitor can be done
with a HDMI cable (not supplied) if your
monitor has a HDMI input.
Video connections to a monitor can be done
with RCA-type video connections.
1. Turn off the power to the Blu-ray player
and the monitor(s) before making any
connections.
2. Connect the HDMI OUT jack on the
rear of the unit to the HDMI IN jack on
your monitor using a HDMI cable (not
included).
3. Select the resolution of the player’s
HDMI output signals to match your
monitor’s resolution capabilities. See the
instructions on page 26 for details.
1. Turn off the power to the Blu-ray player
and the monitor(s) before making any
connections.
2. Connect the LINE OUTPUT jacks on the
rear of the unit to the AUDIO/VIDEO IN
jacks on your monitor using an audio/
video cable (supplied).
Match the color-coded plugs to the
appropriate jacks: Yellow (video) to
Yellow, White (left audio) to White, and
Red (right audio) to Red.
Monitor
AUDIO
IN
Monitor
VIDEO IN
To HDMI
input
Audio/Video cable
(supplied)
HDMI cable
(not supplied)
To HDMI
output
Rear of the unit
Rear of
the unit
Notes
• Refer to the owner’s manual of the
connected monitor as well.
• HDMI, the HDMI logo and HighDefinition Multimedia Interface are
trademarks or registered trademarks of
HDMI licensing LLC.
• If your monitor is a high definition
monitor with an HDMI input, we highly
recommend you use the player’s HDMI
output to get the highest possible video
resolution.
Audio/Video cable
(supplied)
Notes
• If one of the devices is not working,
check that all the cables have been
inserted properly into the jacks.
• If your component has only one input
for audio (mono), connect it to the
left (white L/Mono) audio jack on the
monitor and don’t connect the right
audio part of the cable.
- 10 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Controls and Indicators
1 2
3
2
Front Panel
4
5
6
7 8 9
10
11
12
7. Infrared Remote Sensor
Detects signals from the remote control.
1. Power (
) Button
Press this button to turn on your player.
Press and hold this button for five
seconds to turn off your player.
8.
2. Power Indicator
Illuminates blue when the player is on.
, , , Buttons
Press , , or to navigate through
a menu.
9. Standby Indicator
Illuminates red when the player is off
(standby mode).
3. Disc Slot
Accepts Blu-ray discs, DVDs or CDs.
Insert the disc into the slot with the
label facing up (for a single-sided disc).
10. ENTER Button
Press this button to confirm your
selection.
4. USB Port
Connect a USB flash drive to this port.
5. Previous (
) and Next (
) Buttons
Press
to go to the previous chapter
(Blu-ray Disc/DVD) or track (CD).
Press
to go to the next chapter
(Blu-ray Disc/DVD) or track (CD).
6. MENU Button
Press this button to access the disc
menu during playback. Press this button
again to resume playback.
11. Stop ( ) and Play/Pause (
)
Buttons
Press to stop playback.
Press
to start or resume playback.
When a disc is playing, press
to
pause playback.
12. Eject (
Press
disc.
) Button
to stop playback and eject the
- 11 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Remote Control Operation
Using the Remote Control
Battery Replacement
• Point the remote control at the Infrared
Remote Sensor located on the player
or the REMOTE SENSOR located on the
External Remote IR Receiver.
When the batteries become weak, the
operating distance of the remote control
is greatly reduced and you will need to
replace them.
• When there is a strong ambient light
source, the performance of the infrared
REMOTE SENSOR may be degraded,
causing unreliable operation.
Caution: Danger of explosion if batteries
are incorrectly replaced. Replace only
with the same or equivalent type.
To Install Batteries:
1. Open the battery
door.
2. Insert two AAA
batteries.
Make sure that
the proper
polarity (+ or -) is
observed.
3. Close the door.
Notes
• If you are not using the remote control
for a long period of time, remove the
batteries.
• Do not mix different types of batteries
or new and old batteries.
• Do not use rechargeable batteries.
- 12 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Remote Control Operation
1. STANDBY/ON (
) Button
Press this button to turn on your player.
Press and hold this button for five
seconds to turn off your player (standby
mode).
Remote Control
STANDBY/ON
EJECT
16
1
2
3
4
R
B
G
Y
1
2
3
4
5
6
7
8
9
CLEAR
0
GOTO
MUTE
5
POP UP
6
17
18
19
20
21
22
7
23
8
EXIT
BD/USB
PIP
SETUP
24
9
STEP
10
11
12
13
14
15
AUDIO
INFO
ANGLE
ZOOM
REPEAT
A-B
MENU SUBTITLE
25
26
27
28
29
2. R (red), G (green), B (blue), Y (yellow)
Buttons
When playing a Blu-ray Disc that has a
Java application, press R, G, B or Y to
control playback. For more information,
see the documentation that came with
the Blu-ray Disc.
3. Number Buttons
Press the number buttons to input a
number or select a track, a chapter, etc.
4. CLEAR Button
Press this button to clear an input.
5. Previous(
) Button
Press this button to go to the previous
chapter (Blu-ray Disc/DVD) or track (CD).
6. Fast Reverse (
) Button
Press this button repeatedly for fast
reverse playback. The available speeds
are 2X, 4X, 8X, 16X, and 32X.
7.
, , , Buttons
Press , , or to navigate through
a menu.
8. BD/USB Button
Press this button to select BD (Blu-ray
Disc) or USB mode. You must stop BD or
USB playback prior to switching modes.
9. EXIT Button
Press this button to return to the
previous menu.
10. Stop ( ) Button
Press this button to stop playback.
11. AUDIO Button
Press this button repeatedly to select the
audio languages available on the disc.
- 13 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Remote Control Operation
12. INFO Button
Press this button to access the
Information Menu.
13. REPEAT Button
Press this button to repeat a chapter or
title of a BD/DVD. This function may not
be available on some Blu-ray discs.
Press this button to repeat a chapter,
title or all.
14. A-B Button
Performs point-to-point repeat playback
on a BD/DVD. Press to repeat a specific
section of a disc. Press this button to
mark down the starting point (A) and
press it again to mark down the ending
point (B). The unit will play back this
section over and over again. Press this
button a third time to cancel A-B repeat
and resume normal playback.
This function may not be available on
some Blu-ray discs.
15. Play ( ) Button
Press this button to start or resume
playback.
16. Eject Button
Press this button to stop playback and
eject the disc.
17. GOTO Button
Press this button to search for a title,
chapter, track or angle.
18. MUTE Button
Press this button to mute / unmute the
audio.
19. Next (
) Button
Press this button to go to the next
chapter (BD/DVD) or track (CD).
20. POP UP Button
During Blu-ray Disc playback, press this
button to open a pop-up menu that lets
you control Blu-ray Disc playback.
During DVD playback, press this
button to open the DVD title menu (if
available).
21. Fast Forward (
) Button
Press this button repeatedly for fast
forward playback. The available speeds
are 2X, 4X, 8X, 16X, and 32X.
22. OK Button
Press this button to confirm your
selection.
23. PiP Button
Press this button to turn PiP (picture in
picture) mode on or off. This function is
only available to Blu-ray discs if available
on disc.
24. SETUP Button
Press this button to enter the Home
(Setup) Menu when the player is in full
stop mode.
25. STEP ( ) Button
Press this button to pause playback.
Press this button again to advance to
the next frame.
26. ZOOM Button
Press this button to zoom in to a scene.
The available zoom ratios are 2x, 3x, and
4x. When you are zoomed in, you can
use the direction buttons to move (pan)
the zooming center.
27. ANGLE Button
Press this button to access the camera
angle function for multi-angle BD/DVD
discs, if available on disc.
28. SUBTITLE Button
Press this button to select one of the
subtitle languages programmed on a
BD/DVD.
29. MENU Button
Press this button to access the disc
menu during playback. Press the button
again to resume playback.
- 14 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Playing a Blu-ray Disc or DVD
Basic Playback (Blu-ray Disc or
DVD)
To Play a BD/DVD:
Stop
1. Turn on your monitor.
• Press the
2. Press the STANDBY/ON (
) button on
the remote control or the
POWER (
) button located on the
player’s front panel. The blue LEDs on
both sides of the disc slot illuminate.
• The player stores the point where
playback was interrupted.
BD playback - If you press the button,
you will be asked to resume playback.
Select “Yes” to resume or “No” to return to
the disc menu.
DVD playback - If you press the button,
playback resumes from the point it was
interrupted.
3. Insert a disc label-side up into the disc
slot. The disc will load automatically and
begin to play.
If the disc menu appears, select the Play
option and press the OK button to begin
playback.
4. To eject the disc, press the
button on
the front panel or the EJECT button on
the remote control.
• To stop playback completely or to start
again from the beginning, press the
button twice.
Note
Playback
• To start playback, press the
• When you leave the player in stop mode
for more than 20 minutes, the screen
saver is activated if you set the Screen
Saver to On. At the end of 30 minutes
without any user interaction, the player
switches off automatically.
button.
Pause
• To pause playback, press the
button
on the front panel or the STEP ( )
button on the remote control.
• To resume normal playback, press
the button.
Accelerated Play
Frame Advance
• Press the STEP ( ) button on the remote
control twice. The step forward (
)
symbol is displayed.
• Each time you press the STEP ( ) button,
the video advances by one frame.
• Press the
playback.
button to resume normal
button to stop playback.
• To fast-forward, press the
button.
• To fast-reverse, press the
button.
• Each time you press one of these buttons,
the fast-forward or fast-reverse speed
increases from 2X, 4X, 8X, 16X to 32X.
• Press the
playback.
button to resume normal
Changing the Chapter/Title
• Press the Previous (
) button to skip to
the start of the current chapter or skip to
previous chapters.
• Press the Next (
) button to skip to the
beginning of the next chapter.
- 15 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Playing a Blu-ray Disc or DVD
Zoom
Displaying Disc Information
• While a disc is playing, press the ZOOM
button until you reach the zoom size you
want. Each time you press the ZOOM
button, the magnification level changes
as follows:
• Press the INFO button. Your player
displays information about the disc,
such as type of disc, elapsed time of
the current title, title number, chapter
number, audio format, and subtitle
language.
• To move from one area to another (pan),
use the , , or buttons.
• When the magnification is at 4x, press the
ZOOM button to return the video to its
original size.
Notes
• The ZOOM feature may not be available
on some discs.
• Press the INFO button again to exit.
Notes
• The information displayed for discs
other than Blu-ray Discs will be different.
• “ ” will be displayed if the function
you select is not available.
• “ ” will be displayed if the function
you select is not available.
- 16 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Playing a Blu-ray Disc or DVD
Special Functions
Repeating a Title or Chapter
Selecting the Audio Mode
• Press the REPEAT button one or more
times to select a repeat mode. This
function may not be available on some
Blu-ray discs.
Options: Repeat Chapter, Repeat Title
(TT), Repeat All, Repeat Off
1. Press the AUDIO button. Your player
displays the disc’s audio channel
information, such as 1/3 English Dolby
Digital 2 CH.
2. Press the AUDIO button repeatedly to
select the desired audio language.
Using Picture-in-Picture (PIP) Mode
Some Blu-ray Discs are compatible with
picture-in-picture (PiP) mode. In PiP mode,
the primary video is displayed on the full
screen, and the secondary video is displayed
in a small window.
Selecting Subtitles
You can select a subtitle language from
those included on the BDs or DVDs.
Press the SUBTITLE button on the remote
control repeatedly to select your desired
language.
Selecting the Camera Angle (Blu-ray
Disc and DVD)
Primary video
Some discs offer different camera angles for
specific scenes. To change the camera angle:
Secondary video
1. While you are playing a disc with
different angles recorded, press the
ANGLE button to view the number of
current angles available.
• Press the PiP button to turn PiP mode on
or off.
2. Press the ANGLE button repeatedly to
change the scene to the next angle in
those recorded.
Note
• Some discs allow you to turn PiP on/off
only via the disc menu.
• This function can only be used for discs
on which scenes shot from multiple
angles have been recorded.
Using a Disc Popup Menu
1. During Blu-ray or DVD playback, press
the POP UP button. The Blu-ray popup
menu or the title menu of DVD disc
opens.
• If only one angle is recorded, “
displayed.
” is
2. Press the , , or buttons to select
an option, then press the OK button.
3. Press the POP UP button again to exit
the popup menu.
- 17 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Playing a Blu-ray Disc or DVD
Locating a Desired Section
Locating a specific time in a DVD or
Blu-ray Disc
Locating a specific title in a DVD or
Blu-ray Disc
1. Press the GOTO button.
1. Press the GOTO button.
2. Press the the OK button. The hour is
highlighted in yellow.
2. Press the or button to move the
cursor to the title, then press the OK
button. The title is highlighted in yellow.
BD
AVC
2 / 4
2 / 18
TT
00 :0 0 : 00
2 / 2 English
1/2 English DTS-HD MA 5.1
BD
AVC
1/2 English DTS-HD MA 5.1
3. Press the or buttons to move the
cursor to the hour, minute or second.
• The first two numbers represent hours.
• The second two numbers represent
minutes.
2 / 4
2 / 18
TT
00 :01 : 25
2 / 2 English
3. Press the or button or the
corresponding number buttons (1-9)
for the title you want, then press the OK
button to confirm. Playback starts from
the selected title.
• The third two numbers represent
seconds.
4. Press the or buttons or the
corresponding number buttons (1-9) for
the time you want, then press the OK
button to confirm. Playback starts from
the selected time.
Locating a specific chapter in a DVD or
Blu-ray Disc
1. Press the GOTO button.
2. Press the or button to move the
cursor to the chapter, then press the OK
button. The chapter is highlighted in
yellow.
BD
AVC
1/2 English DTS-HD MA 5.1
2 / 4
2 / 18
TT
00 :01 : 25
2 / 2 English
3. Press the or button or the
corresponding number buttons (1-9) for
the chapter you want, then press the OK
button to confirm. Playback starts from
the selected chapter.
- 18 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Playing an Audio CD
Basic Playback (Audio CD)
To Play an Audio CD:
Accelerated Play
1. Press the STANDBY/ON (
) button on
the remote control or the
POWER (
) button located on the
player’s front panel. The blue LEDs on
both sides of the disc slot illuminate.
• To fast-forward, press the
button.
• To fast-reverse, press the
button.
2. Insert a disc label-side up into the disc
slot. The disc will load automatically and
begin to play.
• To resume normal playback, press
the button.
Changing the Track
3. To eject the CD, press the
button on
the front panel or the EJECT button on
the remote control.
• Press the
button to skip to the start
of the current track or skip to previous
tracks.
Playback:
• To start playback, press the
• Each time you press one of these buttons,
the fast-forward or fast-reverse speed
increases from 2X, 4X, 8X, 16X to 32X.
• Press the
button to skip to the
beginning of the next track.
button.
Pause
• To pause playback, press the
button
on the front panel or the STEP ( )
button on the remote control. The sound
is muted when your unit is in pause
mode. To resume normal playback, press
the button.
Repeating a CD Track
• Press the REPEAT button one or more
times to select a repeat mode.
Options: Repeat Once, Repeat All, Repeat
Off.
• To stop playback completely, press the
button. To start playback again, press the
button.
- 19 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Playing Picture Files
Basic Playback (Picture Files)
This unit can play picture files stored on Bluray Disc (BD), USB flash drives, CD-R/CD-RW,
DVD+R/-R or DVD+RW/-RW discs.
To Play Picture Files (JPEGs) from a USB
Flash Drive:
1. Insert the USB drive containing JPEG
files.
2. If a BD, DVD or CD is playing, stop
playback of the disc.
3. Press the BD/USB button. The Media
Center Menu appears on the monitor
screen.
4. Use the button to highlight USB1.
Press the OK button to select the USB
folder.
Notes
5. Press the button to select the Photo
folder and press the OK button.
• You can press the corresponding
number buttons (0-9) to select the
photo you want.
6. Press the or button to select a
file (or a folder) and press the OK or
button to start playback. If you
selected a folder, the files in this folder
are displayed. Press the or button
to select a file and press the OK or
button to start playback.
7. Press press the
playback.
• The player does not support USB hard
disc mass storage devices, multi-card
readers, and other USB computer
peripherals.
• Do not disconnect the USB flash drive
when you are playing files, it may
corrupt the data.
button to stop
• If you cannot easily insert the USB
flash drive, you may have inserted it
incorrectly. Try to turn over the USB
device and insert it again.
8. Press press the button to return to the
Media Center Menu
9. Remove the USB drive when you are
finished
- 20 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Playing Picture Files
To Play Kodak Picture CDs:
5. Press press the button to return to the
Media Center Menu.
1. Insert a Kodak Picture CD label-side
up into the disc slot. The disc will load
automatically and begin to play.
Viewing Files
Play / Pause:
2. Press the button on the remote
control to enter to enter the thumbnail
mode to preview the pictures.
• Press the STEP ( ) button to pause
playback. Press the button to resume
playback.
3. In the thumbnail mode, press the ,
, or cursor button to select a
picture, then press the OK or button
to start the playback from the selected
picture.
Skip to the Previous/Next Picture:
• Press the Previous (
) button to skip to
the previous picture during playback.
• Press the Next (
) button to skip to the
next picture during playback.
4. Press the or button to rotate a
picture. Press the or button to flip
a picture.
Picture Rotation:
5. Press the EJECT button to stop playback
and eject the disc.
• During playback, press the or button
to rotate a picture on the monitor screen.
Press the or button to flip a picture.
To Play Picture Files (JPEGs) from a
Disc:
Zoom In / Out:
1. Insert a CD label-side up into the disc
slot. The Media Center Menu appears on
the monitor screen.
• Press the ZOOM button until you
reach the zoom size you want. Each
time you press the ZOOM button, the
magnification level changes as follows:
• When the picture is zoomed in, move
from one area to another (pan) using the
, , or buttons.
• When the magnification is at 4x, press the
ZOOM button to return the picture to its
original size.
2. Press the button to select the Photo
folder and press the OK button.
Slide Show Speed
3. Press the or button to select a
file (or a folder) and press the OK or
button to start playback. If you
selected a folder, the files in this folder
are displayed. Press the or button
to select a file and press the OK or
button to start playback.
4. Press press the
playback.
• Press the
or
button to increase or
decrease the slide show speed.
Options: Slow, Medium, and Fast.
button to stop
- 21 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
The Home (Setup) Menu
The Home (Setup) Menu allows you to
personalize the player’s settings to your
preference. Once the initial settings are set,
they are retained in the player’s memory
until modified.
When you leave the unit in stop mode for
more than 20 minutes, the screen saver of
the unit automatically appears if you set the
Screen Saver to On mode.
General Setting Menu
1. Press the SETUP button while in full
stop mode. The Home Menu appears.
If you choose OK in the prompt message
box and press OK button, all settings will be
restored to the factory defaults.
2. Press the or button to select the
General Setting Menu.
Upgrade
Restore Default Settings
Visit the Audiovox Web site
(www.audiovoxproducts.com) for
information on available upgrades.
Easy Setup
1. In the System menu of General Settings,
press the button, then press the or
button to select Easy Setup, and then
press the OK button.
3. Press the
menus.
button to enter the sub-
4. When finished with your menu
selections, press the SETUP button to
exit.
System Sub-Menu
2. The Settings Wizard launches. Follow the
on-screen instructions to customize the
following settings to your preference:
• Player Menu
Options: English, French or Spanish
1. In the General Setting menu, press the
or button to select System.
• HDMI Resolution
Options: Auto, 480i, 480p, 720p, 1080i
or 1080p
2. Press the button and press the or
button to select a setting, then press the
OK button.
• TV Screen
Options: 16:9 Full, 16:9 Pillarbox,
4:3 Pan & Scan or 4:3 Letterbox
3. Press the or buttons to select the
desired option, and then press the OK
button to confirm your selection.
3. After customizing your settings, press
the OK button to confirm and exit Easy
Setup.
4. Press the button to go to the previous
menu.
Settings
Screen Saver
This Blu-ray disc player has a screen saver
feature when your player is inactive. You can
set it to On or Off to turn on/off the screen
saver.
Note
• When the player is turned on for the
first time or after resetting it to the
factory default, the Easy Setup menu
will pop up. Please follow above steps
to finish the setup.
- 22 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
The Home (Setup) Menu
Language Sub-Menu
1. In the General Setting menu, press the
or button to select Language.
2. Press the button and press the or
button to select a setting, then press the
OK button.
3. Press the or buttons to select the
desired option, and then press the OK
button to confirm your selection.
4. Press the button to go to the previous
menu.
Settings
Player Menu
This setting allows you to select the
preferred on-screen display language.
Options: English, French or Spanish.
Disc Menu
This setting allows you to select the
preferred disc menu language.
Options: English, French or Spanish.
Notes
Audio
• If the selected language is not available
on a disc, the disc’s language will be
used instead.
This setting allows you to select the
preferred audio language.
• If the language chosen is available, it
is automatically selected when you
display the subtitles or press SUBTITLE
button on the remote control.
Otherwise, the subtitle language
indicated on the disc is selected.
Options: English, French or Spanish.
Subtitle
This setting allows you to select the
preferred subtitle language.
Options: Off, English, French or Spanish.
- 23 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
The Home (Setup) Menu
Security Sub-Menu
Parental Control
1. In the General Setting menu, press the
or button to select Security.
This player has a built-in parental control
lock feature to prevent unauthorized
persons from viewing restricted disc
content. Parental controls allow you to limit
the content of movie playback from Kid Safe
to Adult. By default, the parental lock is off.
Once set up, the parental lock is released
only by entering the correct password or by
following the instructions provided by the
disc.
2. Press the button and press the or
button to select Change Password or
Parental Control, and then press the OK
button.
3. Follow the prompts as described below.
Settings
Change Password
A new password can be set to replace the
default password. The default password is
3308.
1. Select Change Password as described
above.
2. Enter the current password (a 4-digit
number).
3. Enter a new 4-digit password in the
“New password” row. The password is
set.
4. Enter the new 4-digit password again
in the “Confirm password” row. The
password is set.
Notes
1. Select Parental Control as described
above.
2. Enter the current password (a 4-digit
number).
3. Press the or button to select the
rating level you want to block, and then
press the OK button. The selected rating
and all higher ratings will be blocked.
You can select the following:
Off
KID SAFE Suitable for all children.
G
General audiences.
PG
Parental guidance suggested.
PG-13
Not suitable for anyone under 13.
PGR
Parental guidance recommended.
• You may reset the password if you
forgot the old password by using the
default password: 3308.
R
Not suitable for anyone under 17
unless supervised by a parent or
adult guardian.
• The default password is 3308. This
password is always active even after
you have selected your own password
and changed it. To avoid the possibility
of others using the default password
to change the password or set the
parental code, record the default
password in another area and delete it
from this manual.
NC-17
Not suitable for anyone under 17.
ADULT
All Blu-ray™ Discs and DVDs can
be played.
4. Press the OK button to set the parental
level.
Note
• The parental lock feature may not be
available on some discs.
- 24 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
The Home (Setup) Menu
Display Setting Menu
1. Press the SETUP button while in full stop
mode. The Home Menu appears.
2. Press the or button to select the
Display Setting Menu
Use cursor button to move focus,
use “OK” button to select
3. Press the
menus.
16 : 9 Pillarbox:
The video will be “squeezed” between two
vertical columns on the TV screen. This will
cause standard definition 4:3 video to be
displayed correctly on an wide-screen TV,
but will distort 16:9 video.
4 : 3 Pan and Scan:
When high-definition 16:9 video is played,
this mode clips the right and left sides of
the video so that it can be viewed with the
correct aspect ratio on an older analog TV
that has 4:3 aspect ratio. This setting will
distort video played on a wide-screen TV.
SETUP
button to enter the sub-
Some wide-screen DVDs that do not permit
Pan Scan mode playback are automatically
played in letterbox mode (black bands that
appear at the top and bottom of the screen).
4. When finished with your menu
selections, press the SETUP button to
exit.
TV Sub-Menu
1. In the Display Setting menu, press the
button to select TV.
2. Press the button and press the or
button to select a setting, then press the
OK button.
3. Press the or buttons to select the
desired option, and then press the OK
button to confirm your selection.
4 : 3 Letterbox:
When high-definition 16:9 video is played in
this mode on an analog 4:3 aspect-ratio TV,
black bands appear at the top and bottom
of the screen.
This will cause high-definition 16:9 video to
be displayed correctly on a 4:3 screen but
will distort standard-definition 4:3 video
displayed on a 4:3 screen, and will distort
video played on a wide screen TV.
4. Press the button to go to the previous
menu.
Notes
Settings
TV Screen
Depending on the type of monitor you
have, you may want to adjust the screen
size setting. The options available are: 16:9
Full, 16:9 Pillarbox, 4:3 Pan and Scan, and 4:3
Letterbox.
16 : 9 Full:
High-definition 16:9 formatted video will
be displayed correctly on a wide-screen TV
(most modern TVs).
• The displayable picture size is preset
on the DVD. Therefore the playback
picture of some DVDs may not conform
to the picture size selected.
• If your TV is 16:9 wide-screen (most
modern TVs are) , then choose either
“16:9 Full” or “16:9 Pillarbox”. If your TV
is 4:3 (an older analog TV), then choose
“4:3 Pan and Scan” or “4:3 Letterbox”.
- 25 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
The Home (Setup) Menu
HDMI Resolution
HDMI 1080P 24Hz
You can define the video output resolution
in this option. The options available are:
Auto, 480i, 480p, 720p, 1080i, and 1080p.
The number indicates the number of
lines of video per frame. The i and p
indicate interlaced and progressive scan,
respectively. The more lines, the higher the
quality.
Movies are recorded on film at a rate of 24
pictures (frames) per second. Many of the
movies are recorded to Blu-ray Discs at this
frame rate. However, not all TVs can display
24 progressive frames/second of video. If
the TV cannot display this frame rate, you
need to turn off HDMI 1080P 24Hz.
Notes
Note
• This setting only applies if the HDMI
output is used.
Auto:
Select if your TV is a high-definition TV
(HDTV), is connected to the HDMI jack on
your player, and you want your player to set
the output resolution based on information
exchanged between the TV and your player
over the HDMI cable.
• Selecting a resolution your TV does
not support could result in an unstable
picture or loss of the picture. See the
documentation that came with the TV
to find the resolutions the TV supports.
• Only the HDMI output on your player
supports 1080p video output at any
frame rate.
480i:
Select if your TV is a standard-definition
NTSC (analog) TV.
480p:
Select if your TV is an enhanced-definition
TV (EDTV).
720p:
Select if your TV is a high-definition TV
(HDTV) capable of 720p only.
1080i:
Select if your TV is a high-definition TV
(HDTV) capable of 1080i only.
1080p:
Select if your TV is a high-definition TV
(HDTV) capable of 1080p (any frame rate)
connected to the HDMI jack on your player.
- 26 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
The Home (Setup) Menu
Audio Setting Menu
Dynamic Range
1. Press the SETUP button while in full
stop mode. The Home Menu appears.
Dynamic Range allows you to make the
loud parts of a movie’s audio track quieter
than they would be in the theatre, without
making the dialog of the actors any quieter.
2. Press the or button to select the
Audio Setting Menu.
This would be useful, for instance, when you
want to watch a movie in the evening when
others might be sleeping.
Off :
Movie soundtracks are played with the
standard dynamic range.
Use cursor button to move focus,
use “OK” button to select
3. Press the
menus.
SETUP
On:
Select when movie soundtracks are played
at low volume or from smaller speakers. Your
player applies appropriate compression to
make low-level content more intelligible
and prevent dramatic passages from getting
too loud.
button to enter the sub-
4. When finished with your menu
selections, press the SETUP button to
exit.
Audio Output Sub-Menu
1. In the Audio Setting menu, press or
button to select Audio Output.
2. Press the button and press the or
button to select a setting, then press the
OK button.
3. Press the or buttons to select the
desired option, and then press the OK
button to confirm your selection.
Auto:
This option turns on the Dynamic Range
Control for all BD movie soundtracks except
Dolby TruHD.
System Information
1. Press the SETUP button to display the
Home Menu while in full stop mode.
4. Press the button to go to the previous
menu.
2. Press the or button to select System
Information.
• The player’s software version information
is displayed.
Settings
HDMI
3. Press the SETUP button to exit.
Raw Disc Format:
The disc’s raw (native) audio format will be
output over HDMI.
PCM:
Select when the player is connected to a
multi-channel digital stereo amplifier via
HDMI.
- 27 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Reference
To get the optimum use out of your Blu-Ray player, please read this section completely.
Blu-Ray Region Codes
This player is preset to a region code at the factory depending on where the player is sold.
Blu-ray Discs (BDs) are also coded by region. These region codes must match in order for the
disc to play. If the region codes don’t match, the disc won’t play.
The letter inside the globe refers to region of the world. This player has been designed to
play back Blu-ray Disc (BD) video encoded for region “A”. You cannot play back Blu-ray discs
that are encoded for other regions.
A
C
A
A
B
Region A - USA, Canada, Central America (including Mexico), South America, Japan, Taiwan,
North Korea, South Korea, Hong Kong , and South East Asia
Region B - Europe, Greenland, Middle East, Africa, Australia, and New Zealand
Region C - India, Nepal, Mainland China, Pakistan, Russia, Central Asia, and South Asia
- 28 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Reference
DVD Region Codes
This player is preset to a region code at the factory depending on where the player is sold.
DVDs are also coded by region. These region codes must match in order for the disc to play. If
the region codes don’t match, the disc won’t play.
The letter inside the globe refers to region of the world. This player has been designed to
play back DVD video encoded for region “1”. You cannot play back DVDs that are encoded
for other regions.
Region 1 - USA, Canada
Region 2 - Japan, Europe, South Africa, Middle East, Greenland
Region 3 - S. Korea, Taiwan, Hong Kong, Parts of South East Asia
Region 4 - Australia, New Zealand, Latin America (including Mexico)
Region 5 - Eastern Europe, Russia, India, Africa
Region 6 - China
- 29 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Reference
Compatible Formats
Audio CDs
In order to ensure playback, discs must
conform with BD, DVD or CD standards.
This unit may not play some recordings or
files due to differences in recording formats,
software used, and disc types.
Audio CDs (12 cm).
BD-ROM
BD-ROMs (Blu-ray Disc Read-Only Memory)
are commercially produced discs and are
available in the same capacities as BD below.
Other than conventional movie and video
contents, these discs have enhanced features
such as interactive content, menu operations
using pop-up menus, selection of subtitle
display, and slide show. Although a BD-ROM
may contain any form of data, most BD ROM
discs will contain movies in High Definition
format, for playback on Blu-ray Disc players.
Blu-ray Disc (BD)
A disc format developed for recording/
playing high-definition (HD) video (for
HDTV, etc.), and for storing large amounts of
data. A single layer Blu-ray Disc holds up to
25 GB of data, and a dual-layer Blu-ray Disc
holds up to 50 GB of data.
DVD-Video
Digital video discs - 12 cm, single or double
sided, single or dual layer. DVDs are high
density optical discs on which high quality
picture and audio are recorded by means of
digital signals.
DVD-R, DVD-RW, DVD+R, DVD+RW
Most DVD-R and DVD+R (one recording
only), DVD-RW and DVD+RW discs
(rewritable), depending on the DVD
writer and discs used.
DVD+Rewritable
Recordings using DVD-R and DVDRW discs must be made in Video DVD mode.
Recordings using DVD+RW discs must be
made in accordance with the specifications
for DVD+RW discs with a 4.7 GB capacity.
CD-R, CD-RW
Most CD-R (one recording only) and CD-RW
discs (rewritable).
CD-Rs written during a multisession
recording can be played, provided that the
session has ended before the disc is played
(depending on the write software).
However, depending on the condition of the
CD-writer, computer, and the disc used, you
may find that not all discs will play. When
playing a CD-R disc, it is normal for the unit
to take up to 60 seconds to recognize the
disc before starting to play.
If the disc is not recognized after a period
of 120 seconds, remove the disc, and insert
it again.
• Do not use its full capacity.
• CD-Rs should be preferably used instead
of CD-RWs (rewritable CDs) as, in certain
cases, CD-RW playback may be faulty.
• Use reliable, good-quality CD write
software.
• Close all other applications on the
computer to ensure reliable CD-R disc
recording.
JPEG Files
CD-R and CD-RW with JPEG files. Certain
JPEG files, including progressive JPEG files,
cannot be read by this unit.
The total number of files and folders on the
disc should be less than 650. Make sure that
files have the “.jpg” extension. Files without
the “.jpg” extension will not be able to be
read by the unit - even though the files are
shown as JPEG images on your computer.
- 30 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Reference
“Blu-ray Disc” and
DVD copy protection
are trademarks.
In accordance with the DVD standard, your
player is equipped with a Copy Protection
system, which can be switched on and off
by the DVD disc itself, in order to make any
recording of the relevant DVD disc onto a
videotape of very poor picture quality, or
even impossible.
Manufactured under
license from Dolby
Laboratories. Dolby and
the double-D symbol
are trademarks of Dolby
Laboratories.
HDMI, the HDMI logo and
High-Definition Multimedia
Interface are trademarks or
registered trademarks of
HDMI Licensing LLC.
Manufactured under
license under U.S. Patent
Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S.
and worldwide patents
issued & pending. DTS,
the Symbol, & DTS and
the Symbol together are
registered trademarks
& DTS 2.0+Digital Out is
a trademark of DTS, Inc.
Product includes software.
© DTS, Inc. All Rights
Reserved.
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents and
other intellectual property rights owned by
Rovi Corporation and other rights owners.
Use of this copyright protection technology
must be authorized by Rovi Corporation,
and is intended for home/mobile use
only unless otherwise authorized by Rovi
Corporation.
Reverse engineering or disassembly is
prohibited.
Java and all Java-based
trademarks and logos are
trademarks or registered
trademarks of Oracle
America, Inc. in the U.S. and
other countries.
- 31 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Specifications
BD Video Format
1080 pixel (horizontal) x 1920 pixel (vertical)
DVD Video Format
720 pixel (horizontal) x 480 pixel (vertical)
HDMI Output
Single Type A, 1.2a compliant
Video Output
1.0 Vp-p / 75 Ohm
Audio Output
1.2 V to 1.8 V
Signal-to-Noise Ratio
More than 60 dB
Harmonic Distortion
Less than 60 dB
Dynamic Range
More than 70 dB
Power Source
12 VDC
Power Consumption
Less than 1 Watt in stand-by mode and less than
15 Watts in use
USB 2.0 Compatible
Supports flash stick type devices (≤500mA), FAT32/16
file system, max capacity 32GB (Hard Disks and other
computer peripherals are not supported.)
Dimensions
AVDBR1 Mounting Dimensions
Chassis Width
7.053”
Chassis Height
2.0981”
Chassis Depth
7.50”
Chassis Depth with RCAs and
Harness
8.25”
Remote Control Dimensions
Width
2.068”
Height
7.535”
Depth
0.77”
Weight
Net Weight
2 lbs
Package Weight
4 lbs
- 32 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Troubleshooting
Problem
Solution
The player does not switch
on.
• Make sure the power wires are properly connected.
• Make sure the fuse has not blown. If the fuse has blown,
check for short circuits. Replace the fuse with a fuse of the
same rating.
• Press the STANDBY/ON button on the remote control or the
Power (
) button on the front of the unit.
The player switches off
spontaneously.
• The player will switch off automatically if it remains idle
and there is no user interaction for 30 minutes. Switch it
on again.
Blu-ray Disc or DVD does
not play.
• Make sure that the disc has the correct region code.
• Some Blu-ray discs will only play over an HDMI
connection.
• It may be impossible to read the disc.
• Insert the disc with the printed side facing up.
• Check that the disc can actually be played by this device.
• Clean the disc.
Picture-in-Picture (PiP) does
not work on a Blu-ray Disc.
• Make sure that the disc supports PiP mode.
There is no picture.
• Check that the monitor is operating correctly.
• Check the connections.
• Replace the HDMI cable with a better one. A bad HDMI
cable can cause loss of video.
The picture is of poor
quality (with snow or lines).
• Check the connections.
There is no sound or the
sound is of poor quality.
• Check the connections.
• Make sure the speakers are connected.
• Make sure the MUTE function is not on.
A file can’t be found in the
JPEG listing.
• Make sure the file name is valid.
The remote control does
not work or works only
intermittently.
• Check that batteries are properly inserted.
• The batteries are discharged. Change them.
• Aim the remote control at the player or the External
Remote IR Receiver. The infrared beam must not be
blocked or interrupted.
The subtitles do not appear.
• Check that the BD/DVD disc provides subtitles.
• Refer to the section on how to display subtitles.
The disc menu language is
not the correct one.
• The language of your choice is not available on the disc.
“
• The feature or action is not available.
” is displayed.
- 33 -
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
12 MONTH LIMITED WARRANTY
Applies to Audiovox Mobile Video Products
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail
purchaser of this product that should this product or any part thereof, under normal
use and conditions, be proven defective in material or workmanship within 12 months
from the date of original purchase, such defect(s) will be repaired or replaced with
reconditioned product (at the Company’s option) without charge for parts and repair
labor. A game controller, if supplied, is similarly warranted for ninety (90) days.
To obtain repair or replacement within the terms of this Warranty, the product is to
be delivered with proof of warranty coverage (e.g. dated bill of sale), specification
of defect(s), transportation prepaid, to the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or
noise, to correction of antenna problems, to costs incurred for installation, removal or
reinstallation of the product, or to damage to digital memory/media devices, gaming
devices, discs, speakers, accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the
opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by
removal or defacement of the factory serial number/bar code label(s).
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY
IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE
AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS
WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY
HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM
DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY
BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or representative is authorized to assume for the Company any liability other
than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limitations
or exclusions may not apply to you. This Warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788
 1-800-645-4994
128-5495F
For Sales Information Please Contact
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281