ProSpray 3.39 - Manuais Online

GB
Operating manual
ProSpray 3.39
Airless high-pressure spraying unit
Model:
0558054
Original operating manual
0558079
ProSpray 3.39
Edition 5 / 2014
0558 977L
GB
Warning!
Attention: Danger of injury by injection!
Airless units develop extremely high spraying pressures.
1
Never put your fingers, hands or any other parts of the body into
the spray jet!
Never point the spray gun at yourself, other persons or animals.
Never use the spray gun without safety guard.
Do not treat a spraying injury as a harmless cut. In case of injury
to the skin through coating materials or solvents, consult a doctor
immediately for quick and expert treatment. Inform the doctor
about the coating material or solvent used.
2
The operating instructions state that the following points must
always be observed before starting up:
3
The instructions regarding regular cleaning and maintenance of
the unit must be strictly observed.
Before any work is done on the unit or for every break in work the
following rules must be observed:
1.
2.
3.
4.
Faulty units must not be used.
Secure WAGNER spray gun using the safety catch on the trigger.
Ensure that the unit is properly earthed.
Check allowable operating pressure of high-pressure hose and
spray gun.
5. Check all connections for leaks.
1. Release the pressure from spray gun and hose.
2. Secure the WAGNER spray gun using the safety catch on the trigger.
3. Switch off unit.
Be safety conscious!
GB
Contents
Contents
1.
1.1
1.2
1.3
Page
Safety regulations for Airless spraying....................................... 4
Explanation of symbols used............................................................... 4
Electric Safety............................................................................................. 5
Electrostatic charging (formation of sparks or flames)............... 5
2.
General view of application.............................................................. 6
2.1Application................................................................................................. 6
2.2 Coating materials..................................................................................... 6
Starting operation................................................................................. 9
High-pressure hose, spray gun and
separating oil............................................................................................. 9
Control panel indicators........................................................................ 9
Pressure control knob settings..........................................................10
Connection to the mains network...................................................10
Cleaning preserving agent when
starting-up of operation initially.......................................................10
Taking the unit into operation
with coating material............................................................................10
Digital Electronic Spray Control (DESC).........................................11
5.
Spraying technique............................................................................12
6.
Handling the high-pressure hose................................................13
7.
Interruption of work...........................................................................13
ProSpray 3.39
Cleaning the unit (shutting down)..............................................13
Cleaning unit from outside.................................................................13
Cleaning the high-pressure filter......................................................14
Cleaning Airless spray gun..................................................................14
Cleaning the inlet screen.....................................................................14
9.
Remedy in case of faults...................................................................15
10.Servicing...................................................................................................16
10.1 General servicing....................................................................................16
10.2 High-pressure hose...............................................................................16
Description of unit................................................................................ 6
3.
3.1 Airless process........................................................................................... 6
3.2 Functioning of the unit.......................................................................... 6
3.3 Legend for explanatory diagram ProSpray 3.39........................... 7
3.4 Explanatory diagram ProSpray 3.39.................................................. 7
3.5 Technical data........................................................................................... 8
3.6Transportation........................................................................................... 8
3.7 Transportation in vehicle....................................................................... 8
3.8 Painting material setup.......................................................................... 8
3.9 Textured material setup......................................................................... 8
4.
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Page
8.
8.1
8.2
8.3
8.4
11. Repairs at the unit...............................................................................16
11.1 Relief valve................................................................................................16
11.2 Inlet and outlet valve............................................................................16
11.3Packings.....................................................................................................17
11.4 ProSpray 3.39 connection diagram.................................................18
12.Appendix..................................................................................................19
12.1 Selection of tip........................................................................................19
12.2 Servicing and cleaning of Airless hard-metal tips......................19
12.3 Spray gun accessories...........................................................................19
12.4 Airless tip table................................................................................. 20/21
12.5Pump-Runner..........................................................................................22
Sales and service companies........................................................................23
Accessories for ProSpray 3.39.....................................................................24
Spare parts list for main assembly............................................................26
Spare parts list for fluid section..................................................................28
Spare parts list for drive assembly............................................................29
Spare parts list of filter assembly...............................................................30
Spare parts list for upright cart...................................................................31
Important notes on product liability.......................................................32
3+2 years guarantee for professional finishing..................................32
3
Safety Regulations
1.
Safety regulations for Airless spraying
1.1
Explanation of symbols used
GB
• All accessories must be rated at or above the maximum
operating pressure range of the sprayer. This includes spray
tips, guns, extensions, and hose.
This manual contains information that must be read and understood
before using the equipment. When you come to an area that has one
of the following symbols, pay particular attention and make certain
to heed the safeguard.
HAZARD: High Pressure Hose
The paint hose can develop leaks from wear, kinking
and abuse. A leak can inject material into the skin.
Inspect the hose before each use.
This symbol indicates a potential hazard that
may cause serious injury or loss of life. Important
safety information will follow.
Attention
PREVENTION:
• High-pressure hoses must be checked thoroughly before they
are used.
• Replace any damaged high-pressure hose immediately.
• Never repair defective high-pressure hoses yourself!
• Avoid sharp bends and folds: the smallest bending radius is
about 20 cm.
• Do not drive over the high-pressure hose. Protect against
sharp objects and edges.
• Never pull on the high-pressure hose to move the device.
• Do not twist the high-pressure hose.
• Do not put the high-pressure hose into solvents. Use only a
wet cloth to wipe down the outside of the hose.
• Lay the high-pressure hose in such a way as to ensure that it
cannot be tripped over.
This symbol indicates a potential hazard to you
or to the equipment. Important information that
tells how to prevent damage to the equipment or
how to avoid causes of minor injuries will follow.
Danger of skin injection
Danger of fire from solvent and paint fumes
Danger of explosion from solvent, paint fumes
and incompatible materials
i
Only use WAGNER original-high-pressure hoses in
order to ensure functionality, safety and durability.
Danger of injury from inhalation of harmful
vapors
i
HAZARD: EXPLOSION OR FIRE
Notes give important information which should
be given special attention.
Solvent and paint fumes can explode or ignite.
Severe injury and/or property damage can occur.
PREVENTION:
• Do not use materials with a flashpoint below 21° C (70° F).
Flashpoint is the temperature at which a fluid can produce
enough vapors to ignite.
• Do not use the unit in work places which are covered by the
explosion protection regulations.
• Provide extensive exhaust and fresh air introduction to
keep the air within the spray area free from accumulation of
flammable vapors.
• Avoid all ignition sources such as static electricity sparks,
electrical appliances, flames, pilot lights, hot objects, and
sparks from connecting and disconnecting power cords or
working light switches.
• Do not smoke in spray area.
• Place sprayer sufficient distance from the spray object in a
well ventilated area (add more hose if necessary). Flammable
vapors are often heavier than air. Floor area must be
extremely well ventilated. The pump contains arcing parts
that emit sparks and can ignite vapors.
• The equipment and objects in and around the spray area must
be properly grounded to prevent static sparks.
• Use only conductive or earthed high pressure fluid hose. Gun
must be earthed through hose connections.
• Power cord must be connected to a grounded circuit (electric
units only).
• Always flush unit into separate metal container, at low pump
pressure, with spray tip removed. Hold gun firmly against side
of container to ground container and prevent static sparks.
HAZARD: Injection injury
Attention: Danger of injury by injection! A high
pressure stream produced by this equipment can
pierce the skin and underlying tissues, leading to
serious injury and possible amputation.
Do not treat a spraying injury as a harmless cut. In
case of injury to the skin through coating materials
or solvents, consult a doctor immediately for quick
and expert treatment. Inform the doctor about the
coating material or solvent used.
PREVENTION:
• NEVER aim the gun at any part of the body.
• NEVER allow any part of the body to touch the fluid stream.
DO NOT allow body to touch a leak in the fluid hose.
• NEVER put your hand in front of the gun. Gloves will not
provide protection against an injection injury.
• ALWAYS lock the gun trigger, shut the fluid pump off and
release all pressure before servicing, cleaning the tip guard,
changing tips, or leaving unattended. Pressure will not be
released by turning off the engine. The PRIME/SPRAY valve
or pressure bleed valve must be turned to their appropriate
positions to relieve system pressure.
• ALWAYS keep tip guard in place while spraying. The tip guard
provides some protection but is mainly a warning device.
• ALWAYS remove the spray tip before flushing or cleaning the
system.
• NEVER use a spray gun without a working trigger lock and
trigger guard in place.
4
ProSpray 3.39
GB
Safety regulations
1.2
• Follow material and solvent manufacturer’s warnings and
instructions. Be familiar with the coating material’s MSDS
sheet and technical information to ensure safe use.
• Use lowest possible pressure to flush equipment.
• When cleaning the unit with solvents, the solvent should
never be sprayed or pumped back into a container with a
small opening (bunghole). An explosive gas/air mixture can
arise. The container must be earthed.
DANGER — Work or repairs at the electrical
equipment may only be carried out by a skilled
electrician. No liability is assumed for incorrect
installation. Switch the unit off. Before all repair
work, unplug the power plug from the outlet.
HAZARD: HAZARDOUS VAPORS
Paints, solvents, and other materials can be harmful
if inhaled or come in contact with body. Vapors can
cause severe nausea, fainting, or poisoning.
Danger of short-circuits caused by water ingressing into the electrical
equipment. Never spray down the unit with high-pressure or highpressure steam cleaners.
PREVENTION:
• Wear respiratory protection when spraying. Read all
instructions supplied with the mask to be sure it will provide
the necessary protection.
• All local regulations regarding protection against hazardous
vapors must be observed.
• Wear protective eyewear.
• Protective clothing, gloves and possibly skin protection cream
are necessary for the protection of the skin. Observe the
regulations of the manufacturer concerning coating materials,
solvents and cleaning agents in preparation, processing and
cleaning units.
Work or repairs at the electrical equipment:
These may only be carried out by a skilled electrician. No liability is
assumed for incorrect installation.
1.3
Electrostatic charging (formation of sparks or
flames)
Electrostatic charging of the unit may occur during
spraying due to the flow speed of the coating
material. These can cause sparks and flames upon
discharge. The unit must therefore always be
earthed via the electrical system. The unit must be
connected to an appropriately-grounded safety
outlet.
HAZARD: GENERAL
This product can cause severe injury or property
damage.
An electrostatic charging of spray guns and the high-pressure hose
is discharged through the high-pressure hose. For this reason the
electric resistance between the connections of the high-pressure
hose must be equal to or lower than 1 MΩ.
PREVENTION:
• Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
• Pulling the trigger causes a recoil force to the hand that is
holding the spray gun. The recoil force of the spray gun is
particularly powerful when the tip has been removed and
a high pressure has been set on the airless pump. When
cleaning without a spray tip, set the pressure control knob to
the lowest pressure.
• Use only manufacturer authorized parts. User assumes all
risks and liabilities when using parts that do not meet the
minimum specifications and safety devices of the pump
manufacturer.
• ALWAYS follow the material manufacturer’s instructions for
safe handling of paint and solvents.
• Clean up all material and solvent spills immediately to prevent
slip hazard.
• Wear ear protection. This unit can produce noise levels above
85 dB(A).
• Never leave this equipment unattended. Keep away from
children or anyone not familiar with the operation of airless
equipment.
• Device weighs in excess of 36 kg. Three-person lift is required.
• Do not spray on windy days.
• The device and all related liquids (i.e. hydraulic oil) must be
disposed of in an environmentally friendly way.
ProSpray 3.39
Electric Safety
Electric models must be earthed. In the event of an electrical short
circuit, earthing reduces the risk of electric shock by providing an
escape wire for the electric current. This product is equipped with
a cord having an earthing wire with an appropriate earthing plug.
Connection to the mains only through a special feed point, e.g.
through an error protection insallation with INF < 30 mA.
5
General view of application
2.
GB
Description of unit
General view of application
= Recommended
2.1Application
= Not-recommended
recommended nozzle size: FineFinish 0.008“ - 0.014“
Emulsion paints, latex paints
recommended nozzle size: 0.017“ - 0.027“
Anti-corrosive agents, flame retardants, fabric adhesive
recommended nozzle size: 0.021“ - 0.031“
Airless-scrapers
recommended nozzle size: 0.027“ - 0.039“
2.2
PS 3.39
up to 200 m2
200 m2 - 800 m2
more than 800 m2
up to 200 m2
200 m2 - 800 m2
more than 800 m2
Coating materials
3.
Description of unit
3.1
Airless process
The main areas of application are thick layers of highly viscous
coating material for large areas and a high consumption of material.
A piston pump takes in the coating material by suction and conveys it
to the tip. Pressed through the tip at a pressure of up to a maximum
of 221 bar (22,1 MPa), the coating material is atomised. This high
pressure has the effect of micro fine atomisation of the coating
material.
As no air is used in this process, it is described as an AIRLESS process.
This method of spraying has the advantages of finest atomisation,
cloudless operation and a smooth, bubble-free surface. As well as
these, the advantages of the speed of work and convenience must
be mentioned.
Pay attention to the Airless quality of the coating
materials to be processed.
Dilutable lacquers and paints or those containing solvents, twocomponent coating materials, dispersions, latex paints.
No other materials should be used for spraying without WAGNER’s
approval.
Filtering
Despite suction filter and insertion filter in the spray gun, filtering of
the coating material is generally advisable.
Stir coating material before commencement of work.
i
PS 3.34
up to 200 m2
200 m2 - 800 m2
more than 800 m2
Processible coating materials
i
PS 3.31
up to 200 m2
200 m2 - 800 m2
more than 800 m2
PS 3.29
Release agents, oils, undercoats, primers, fillers,
synthetic resin-based paints, acrylic paints
PS 3.25
Object Size
PS 3.23
Materials
PS 3.21
Model
3.2
Attention: Make sure, when stirring up with motordriven agitators that no air bubbles are stirred in. Air
bubbles disturb when spraying and can, in fact, lead
to interruption of operation.
Functioning of the unit
In the following there is a short description of the technical
construction for better understanding of the function.
WAGNER ProSpray units are electrically driven high-pressure spraying
units.
A gear unit transfers the driving force to a crankshaft. The crankshaft
moves the pistons of the material feed pump up and down.
The inlet valve is opened automatically by the upwards movement
of the piston. The outlet valve is opened when the piston moves
downward.
The coating material flows under high pressure through the highpressure hose to the spray gun. When the coating material exits from
the tip it atomizes.
The pressure regulator controls the volume and the operating
pressure of the coating material.
Viscosity
With this unit it is possible to process highly viscous coating materials
of up to around 30.000 MPa·s.
If highly viscous coating materials cannot be taken in by suction, they
must be diluted in accordance with the manufacturer’s instructions.
Two-component coating material
The appropriate processing time must be adhered to exactly. Within
this time rinse through and clean the unit meticulously with the
appropriate cleaning materials.
Coating materials with sharp-edged additional materials
These have a strong wear and tear effect on valves, high-pressure
hose, spray gun and tip. The durability of these parts cane be reduced
appreciably through this.
6
ProSpray 3.39
GB
3.3
Description of unit
Legend for explanatory diagram ProSpray 3.39
1 Spray gun
2 High-pressure hose
3 Oil cup for EasyGlide (EasyGlide prevents increased wear of
the packings)
4 Oil level gauge
5 Pail hook
6 Oil button
7 Suction tube
8 Return hose
3.4
9Cart
10 Relief valve
Lever position vertical – PRIME ( k circulation)
Lever position horizontal – SPRAY ( p)
11 Digital Electronic Spray Control (DESC)
12 Control panel indicators
13 Pressure control knob
14 ON/OFF switch
Explanatory diagram ProSpray 3.39
12
11
1
2
3
9
4
5
10
6
7
8
14
ProSpray 3.39
7
13
GB
Description of unit
3.5
Technical data
Voltage:
Max. current consumption:
Power cord:
Acceptance capacity:
Max. operating pressure:
Volume flow at 12 MPa
(120 bar) with water:
Max tip size:
Max. temperature of the
coating material:
Max viscosity:
Weight:
Special high-pressure hose: Dimensions (L X W X H):
Max sound pressure level:
3.8
100-110 Volt AC, 50 Hz
15 A / 20 A
3 x 1.5 mm2 – 6 m or 4.6 m
2000 Watt
221 bar (22,1 MPa)
i
3.9
5.0 l/min
0.039 inch – 0.99 mm
i
43°C
30.000 MPa·s
50 kg
DN 6 mm, 15 m, connection thread M 16 x 1.5
632 x 568 x 743 mm
80 dB (A) *
This sprayer comes with a filter assembly installed.
If you plan to spray with untextured painting
materials, leave the filter installed.
Textured material setup
This sprayer comes with a filter plug that should be
put in place of the filter whenever spraying textured
materials. Follow these steps to remove the filter
and install the plug.
1. Loosen and remove the filter housing (1) by hand.
2. Remove the adapter spring (2), filter (3), bearing ring (4) and
spring (5) from the housing (7).
3. Make sure the O-ring (6) is still in place. Thread the filter plug
(8) into the housing until secure.
i
* Place of measuring: 1 m in distance from the unit and 1.6
m above the floor, 12 MPa (120 bar) operating pressure,
reverberant floor.
Paint material setup
3.6Transportation
The filter plug should be hand-tightened, but make
sure it is seated fully into the filter housing.
1
Pushing or pulling the unit
Pull out the handle (Fig. 2, Item 1) until it will come no further. Insert
the handle – push the buttons (2) on the spars, and then push in the
handle.
2
3
4
8
6
5
1
2
7
2
3.7 Transportation in vehicle
Secure the unit with a suitable fastening.
8
i
If using this sprayer with textured materials, it is
important that the filter inside of the spray gun be
removed. See section 8.3.
i
If the sprayer will be used for spraying textured
products, removal of the inlet screen in the foot
valve may be necessary. This will allow proper
priming and flow of the textured product. See
section 8.4.
ProSpray 3.39
GB
4.
Starting operation
4.1
High-pressure hose, spray gun and separating
oil
Starting operation
1. Screw the high-pressure hose (2) to the coating material
outlet (Fig. 4, Item 1).
2. Screw the spray gun (3) with the selected tip onto the highpressure hose.
3. Tighten the union nuts at the high-pressure hoses firmly so
that coating material does not leak.
4
3
4.2
Control Panel Indicators
The following is a description of the control panel indicators.
Service
Indicator
Pressure
Indicator
Pressure Indicator
The pressure indicator shows the current operating pressure of the
sprayer. It has three different indications: blinking yellow, solid
yellow, and solid green.
1
Blinking Yellow
When the pressure indicator is blinking yellow, the sprayer is
operating between 0 and 1.4 MPa (14 bar). A blinking yellow
pressure indicator means:
• The sprayer is plugged in and turned “ON”
• The sprayer is at priming pressure (little or no pressure)
• It is safe to move the relief valve between positions
• It is safe to change or replace the spray tip
2
4. Remove the oil cup cap with a straight-slot screwdriver.
5. Fill the oil cup with EasyGlide (Fig. 5) until the oil gauge (4) is
showing that it is full.
Attention
EasyGlide prevents increased wear and tear to the
packings.
i
6. Replace oil cup cap.
7. Press oil button 2-5 times to prime the oiler. Press once for
every eight hours of usage to lubricate the fluid section.
If the pressure indicator begins blinking yellow when
the pressure control knob is set at a higher pressure
and the relief valve is in the SPRAY position, either
the spray tip is worn or the sprayer is in need of
service/repair.
Solid Yellow
When the pressure indicator is solid yellow, the sprayer is operating
between 1.4 MPa (14 bar) and 12 MPa (120 bar). A solid yellow
pressure indicator means:
• The sprayer is at the proper pressure setting for spraying stain,
lacquer, varnish, and multi-colors
ProSpray 3.39
9
Starting operation
GB
Solid Green
When the pressure indicator is solid green, the sprayer is operating
between 12 MPa (120 bar) and 23 MPa (230 bar). A solid green
pressure indicator means:
• The sprayer is at the proper pressure setting for spraying oilbased and latex house paints
• The sprayer is operating at peak performance at a high
pressure setting
• If the pressure indicator goes to solid yellow when the
pressure is set so that it starts at solid green, it indicates one of
the following:
a.
Tip Wear Indicator — when spraying with latex or at high
pressure the solid yellow appears. This means the tip is
worn and needs to be replaced.
b.
Tip Too Large — when a tip that is too large for the sprayer
is put in the gun, the pressure indicator will turn from solid
green to solid yellow.
c.
Fluid Section Wear — if a solid yellow pressure indicator
appears when using a new tip and the pressure is set at
maximum, service may be required (worn packings, worn
piston, stuck valve, etc...).
4.5
Cleaning preserving agent when starting-up
of operation initially
1. Immerse the suction tube (Fig. 8, Item 1) and return hose (2)
into a container with a suitable cleaning agent.
2. Turn the pressure control knob counterclockwise (3) to
minimum pressure.
3. Open the relief valve (4), valve position PRIME
(k circulation).
4. Switch the unit (5) ON.
5. Wait until the cleaning agent exudes from the return hose.
6. Close the relief valve, valve position SPRAY (p spray).
7. Pull the trigger of the spray gun.
8. Spray the cleaning agent from the unit into an open collecting
container.
5
3
4
Service Indicator
The Service indicator is on when the motor is commanded to run.
This indicator is used by service centers to troubleshoot motor
problems.
4.3
Pressure control knob settings (Fig. 7)
1. Minimum pressure setting
2. Black zone – no pressure generation
3. Blue zone – pulsating pressure for cleaning
1
2
1
2
3
4.6 Taking the unit into operation with coating
material
4.4
Connection to the mains network
Attention
The unit must be connected to an appropriatelygrounded safety outlet.
Before connecting the unit to the mains supply, ensure that the line
voltage matches that specified on the unit’s rating plate.
The connection must be equipped with a residual current protective
device with INF ≤ 30 mA.
10
1. Immerse the suction tube (Fig. 8, Item 1) and return hose (2)
into the coating material container.
2. Turn the pressure control knob counterclockwise (3) to
minimum pressure.
3. Open the relief valve (4), valve position PRIME
(k circulation).
4. Switch the unit (5) ON.
5. Wait until the coating material exudes from the return hose.
6. Close the relief valve, valve position SPRAY (p spray).
7. Trigger the spray gun several times and spray into a collecting
container until the coating material exits the spray gun
without interruption.
8. Increase the pressure by slowly turning up the pressure
control knob.
Check the spray pattern and increase the pressure until the
atomization is correct.
Always turn the pressure control knob to the lowest setting
with good atomization.
9. The unit is ready to spray.
ProSpray 3.39
GB
4.7
Digital Electronic Spray Control (DESC)
Current Select Screen
CURRENT SELECT
The Current Select screen allows you to
SELECT-4
toggle between operating in 15 Amp or 20 MENU-1
Amp mode.
To select the Current Select screen, press the #4 key. Pressing the
#2 or #3 allows you to choose the desired mode. When the screen
displays the desired mode, press the #1 key to save and return to the
remaining menu screens.
The Digital Electronic Spray Control (DESC) increases the functionality
of the sprayer. It is installed directly below the pressure control
knob on the control panel. It consists of a display and four function
keys. The display shows various menu screens that allow the user to
customize and monitor sprayer operation using the function keys.
Display
SET MPa
ACTUAL MPa
23.0
22.5
Volume Pumped Screen
VOLUME PUMPED
The Volume Pumped screen shows the
SELECT-4
total number of gallons or liters sprayed by MENU-1
the sprayer.
X
To select the Volume Pumped screen, press GALLONS
LITRES-2
MENU-1
the #4 key.
Function
Keys
i
The pressure control knob overrides the Digital
Electronic Spray Control (DESC) settings. Anytime the
pressure control knob is turned, the sprayer pressure
will change accordingly.
LITRES
The function keys are numbered 1–4. Each key is labeled with an
additional function as well.
#1/Menu Key
Pressing the #1 key scrolls through the available menu screens or
performs a function described on the active menu screen.
#2/g Key
Pressing the #2 key performs a function described on the active menu
screen or increases a value.
#3/h Key
Pressing the #3 key performs a function described on the active menu
screen or decrease a value.
#4/Select Key
Pressing the #4 key selects the active menu screen or performs a
function described on the active menu screen.
Unit Serial # Screen
UNIT SERIAL #
The Unit Serial # screen shows the sprayers
MENU-1
SELECT-4
serial number.
# XXXXXXXXXX
To select the Unit Serial # screen, press the SER
MENU-1
#4 key.
Timers Screen
TIMERS
The Timers screen shows the total time the
SELECT-4
sprayer has been turned on as well as the MENU-1
total time the sprayer has been running (pumping).
Menu Screens
To select the Timers screen, press the #4
key.
ON TIME
RUN TIME
Job Timers Screen
The Job Timers screen allows the user to
reset the “ON TIME” and “RUN TIME” to
track time on specific jobs.
JOB TIMERS
MENU-1
SELECT-4
To select the Job Timers screen, press the
#4 key. “JOB ON” screen will appear. Press
#3 to reset. Press #1 to continue to “JOB
RUN” screen. Press #3 to reset. Press #1
to scroll through the remaining menu
screens.
Several menu screens are available for the user to customize and
monitor sprayer operation. They include Main Screen, Volume
Pumped, Job Volume, Unit Serial #, Timers, Job Timers, Service Time,
Security Code, Prime, and Rapid Clean.
Main Screen
SET MPa
23.0
The Main Screen is the default screen for
ACTUAL MPa
22.5
the control system at sprayer startup.
Pressing the #2 key switches between PSI, Bar and MPa units of
measure. Press the #1 key to scroll through the remaining menu
screens.
XXXX
XXXX
JOB ON
MENU-1
X
RESET-3
JOB RUN
MENU-1
X
RESET-3
Service Time Screen
SERVICE TIME
The Service Time screen allows the user to
SELECT-4
set a service time interval (in hours). Below MENU-1
the set time, the screens shows the current amount of hours on the
sprayer since the last activation of the service timer. To select the
Service Timer screen, press the #4 key.
SERVICE @
XX
To set the service time, press the #2 (up)
RUN HOURS
XX
and/or the #3 (down) keys to the desired
time (run hours will increase/decrease in increments of 25 for each
time you press a key).
When the service time interval is set and met by the run hours, the
display will show a “Service Required” screen. The pump will remain
functional. To return to the Main Screen, press the #1 key. Doing so
will reset the “Service @” and “Run Hours” displayed on the Service
Screen back to 0.
For sprayers equipped with an nine-language Digital
Electronic Spray Control (DESC):
Pressing the #2 key at the Main Screen switches
between PSI, Bar and MPa units of measure.
ProSpray 3.39
X
MENU-1
GALLONS-2
Job Volume Screen
JOB VOLUME
The Job Volume screen allows the user
MENU-1
SELECT-4
to reset a liter counter to track usage on
specific jobs.
XXXX
To select the Job Volume screen, press the GALLONS
MENU-1
RESET-3
#4 key.
Function Keys
i
Starting operation
11
GB
Starting operation Security Code Screen
SECURITY CODE
The Security Code screen allows the user
CHANGE-2
to set a four digit security code to prevent MENU-1
unauthorized use of the sprayer. If a security code has been set, the
control system display will ask for the code at startup. If the correct
code is entered, the display will show the Main Screen and the
sprayer will operate. If the wrong code is entered, the display will
continue to ask for the correct code and the sprayer will be disabled.
To set or change the security code, press the #2 key.
i
If the sprayer is new, no security code is set and the
Main Screen will appear at startup. When setting a
security code for the first time, the “Enter Old Code
Number” screen will appear, and you will need to
enter “1111”.
ENTER OLD CODE
Enter the old security code number to
NUMBER
access the screen that allows the code
change. If the wrong code is entered, the display will continue to ask
for the correct code and the security code cannot be changed.
ENTER NEW CODE
Enter the new security code. Once the
NUMBER
XXXX
new code is entered, the display will
automatically ask that the new code be
RE-ENTER NEW
XXXX
re-entered for verification. If the same new NUMBER
code is re-entered, the display will confirm NEW CODE NUMBER
that the new code has been accepted and ACCEPTED
return to the Main Screen. If the new code
is re-entered incorrectly, the display will return to the “Enter New
Code Number” screen and the process will repeat.
If you forget or misplace your security code, you can contact Wagner
customer service for assistance.
i
5.
Spraying technique
Injection hazard. Do not spray without the tip guard
in place. NEVER trigger the gun unless the tip is
completely turned to either the spray or the unclog
position. ALWAYS engage the gun trigger lock
before removing, replacing or cleaning tip.
The key to a good paint job is an even coating over the entire surface.
Keep your arm moving at a constant speed and keep the spray gun at
a constant distance from the surface. The best spraying distance is 25
to 30 cm between the spray tip and the surface.
25 - 30 cm
Keep the spray gun at right angles to the surface. This means moving
your entire arm back and forth rather than just flexing your wrist.
To inactivate the security function, enter “1111” at
the “Enter New Code Number” screen (this is the
default code that leaves the sprayer unlocked). As a
result, the Main Screen will appear at sprayer startup.
Prime Screen
The Prime screen appears when the
pressure control knob is set at the “MIN”
setting.
PRIME
Rapid Clean Screen
RAPID CLEAN
The Rapid Clean screen appears when the
pressure control knob is set at the RAPID
CLEAN position and the PRIME/SPRAY valve is in the PRIME position.
i
Spraying technique
Keep the spray gun perpendicular to the surface, otherwise one end
of the pattern will be thicker than the other.
Trigger gun after starting the stroke. Release the trigger before
ending the stroke. The spray gun should be moving when the trigger
is pulled and released. Overlap each stroke by about 30%. This will
ensure an even coating.
If there is no action at any menu screen for 30
seconds, the display will go back to the Main Screen.
25 - 30 cm
i
12
25 - 30 cm
If very sharp edges result or if there are streaks in the
spray jet – increase the operating pressure or dilute
the coating material.
ProSpray 3.39
Handling the high-pressure hose
6.
GB
Handling the high-pressure hose
8.
The unit is equipped with a high-pressure hose specially suited for
piston pumps.
The high-pressure hose is to be handled with care. Avoid sharp
bends and folds: the smallest bending radius is about 20 cm.
Do not drive over the high-pressure hose. Protect against sharp
objects and edges.
Never pull on the high-pressure hose to move the device.
Make sure that the high-pressure hose cannot twist. This can be
avoided by using a Wagner spray gun with a swivel joint and a hose
system.
When using the high-pressure hose while working
on scaffolding, it is best to always guide the hose
along the outside of the scaffolding.
i
The risk of damage rises with the age of the highpressure hose. Wagner recommends replacing highpressure hoses after 6 years.
i
Cleaning the unit (shutting down)
A clean state is the best method of ensuring operation without
problems. After you have finished spraying, clean the unit. Under no
circumstances may any remaining coating material dry and harden in
the unit.
The cleaning agent used for cleaning (only with an igni­tion point
above 21 °C) must be suitable for the coating material used.
• Secure the spray gun, refer to the operating manual of the
spray gun.
Clean and remove tip.
For a standard tip, refer to Page 19, Section 12.2.
If a non-standard tip is installed, proceed according to the relevant
operating manual.
1. Remove suction hose from the coating material.
2. Close the relief valve, valve position SPRAY (p spray).
3. Switch the unit ON.
4. Pull the trigger of the spray gun in order to pump the
remaining coating material from the suction hose, highpressure hose and the spray gun into an open container.
Danger of injury through leaking high-pressure
hose. Replace any damaged high-pressure hose
immediately.
Never repair defective high-pressure hoses yourself!
i
Cleaning the unit (shutting down)
Attention
The container must be earthed in case of coating
materials which contain solvents.
Caution! Do not pump or spray into a container with
a small opening (bunghole)!
Refer to the safety regulations.
Use only WAGNER original-high-pressure hoses in
order to ensure functionality, safety and durability.
7.
5. Immerse suction hose with return hose into a container with a
suitable cleaning agent.
6. Turn the pressure control knob into the blue zone - pulsating
pressure for unit cleaning.
7. Open the relief valve, valve position PRIME
(k circulation).
8. Pump a suitable cleaning agent in the circuit for a few
minutes.
9. Close the relief valve, valve position SPRAY (p spray).
10. Pull the trigger of the spray gun.
11. Pump the remaining cleaning agent into an open container
until the unit is empty.
12. Switch the unit OFF.
Interruption of work
1. Open the relief valve, valve position PRIME
(k circulation).
2. Switch the unit OFF.
3. Turn the pressure control knob counterclockwise to minimum
pressure.
4. Pull the trigger of the spray gun in order to release the
pressure from the high-pressure hose and spray gun.
5. Secure the spray gun, refer to the operating manual of the
spray gun.
6. If a standard tip is to be cleaned, see Page 19, Section 12.2.
If a non-standard tip is installed, proceed according to the
relevant operating manual.
7. Depending on the model, leave the suction tube or the
suction hose and return hose immersed in the coating
material or swivel or immerse it into a corresponding cleaning
agent.
8.1
Cleaning unit from outside
First of all pull out mains plug from socket.
Danger of short circult through panetrating water!
Never spray down the unit with high-pressure or
Attention high-pressure steam cleaners.
If fast-drying or two-component coating material is
used, ensure that the unit is rinsed with a suitable
cleaning agent within the processing time.
Attention
Attention
Do not put the high-pressure hose into solvents.
Use only a wet cloth to wipe down the outside of the
hose.
Wipe down unit externally with a cloth which has been immersed in a
suitable cleaning agent.
ProSpray 3.39
13
GB
Cleaning the unit (shutting down) 8.2
Cleaning the high-pressure filter
8.3
Clean the filter cartridge regularly.
A soiled or clogged high-pressure filter can cause a poor spray
pattern or a clogged tip.
1. Turn the pressure regulator knob into the black zone until it
stops (no pressure).
2. Open the relief valve, valve position PRIME
(k circulation).
3. Switch the unit OFF.
Unplug the power plug from the outlet.
4. Unscrew the filter housing (Fig. 10, Item 1). with a strap
wrench.
5. Pull the filter cartridge (2) from the bearing spring (3).
6. Clean all the parts with the corresponding cleaning agent. If
necessary, replace the filter cartridge.
7. Check the O-ring (4), replace it if necessary.
8. Place the bearing ring (5) against the bearing spring (3). Slide
the filter cartridge (2) over the bearing spring.
9. Screw in filter housing (1) and tighten it as far as possible with
the strap wrench.
Cleaning Airless spray gun
1. Rinse Airless spray gun with an appropriate cleaning agent.
2. Clean tip thoroughly with appropriate cleaning agent so that
no coating material residue remains.
3. Thoroughly clean the outside of the Airless spray gun.
Intake filter in Airless spray gun
Disassembly (Fig. 11)
1. Pull protective guard (1) forward vigorously.
2. Screw grip (2) out of the gun housing. Remove intake filter (3).
3. Intake filter congested or defective – replace.
Assembly
1. Place intake filter (3) with the long cone into the gun housing.
2. Screw in grip (2) into the gun housing and tight­en.
3. Slot in protective guard (1).
r
0 ba i
25 0 ps
.360
max
:
ning
War clear
ep
ke of tip
3
1
1
2
5
3
2
4
8.4
Cleaning the inlet screen
The inlet screen will clog and must be cleaned at least once a day.
1. Remove the retaining ring (3) from the foot valve (1) housing.
2. Remove the inlet screen (2) from the foot valve housing (1).
3. Clean thoroughly with the appropriate solvent.
1
2
3
14
ProSpray 3.39
GB
9.
Remedy in case of faults
Remedy in case of faults
Type of malfunction
Possible cause
Measures for eliminating the malfunction
A. Unit does not start
1. Check voltage supply.
2. Turn up pressure control knob.
3.Replace.
B. Unit does not draw in material
1. Relief valve is set to SPRAY (p spray).
2. Filter projects over the fluid level and
sucks air.
3. Filter clogged.
4. Suction hose/suction tube is loose, i.e.
the unit is sucking in outside air.
1. Set relief valve to PRIME (k circulation).
2. Refill the coating material.
3. Clean or replace the filter.
4. Clean connecting points. Tighten suction tube.
1.
2.
3.
4.
5.
1.Replace
2. For selection of a smaller tip, see Tip table on Page 20.
3. Turn pressure control knob clockwise to increase.
4. Clean or replace the filter.
5. Remove and clean or replace relief valve.
Tip heavily worn.
Tip too large.
Pressure setting too low.
Filter clogged.
Coating material flows through the
return hose when the relief valve is in
the SPRAY (p spray) position.
6. Packings sticky or worn.
7. Valve balls worn.
8. Valve seats worn.
6. Remove and clean or replace packings.
7. Remove and replace valve balls.
8. Remove and replace valve seats.
C. Unit draws in material, but the
pressure does not build up
1. No voltage applied.
2. Pressure setting too low.
3. ON/OFF switch defective.
D. Coating material exits at the top of
the fluid section
1. Upper packing is worn.
2. Piston is worn.
1. Remove and replace packing.
2. Remove and replace piston.
E. Increased pulsation at the spray
gun
1. Incorrect high-pressure hose type.
2. Tip worn or too large.
3. Pressure too high.
1. Only use WAGNER original-high-pressure hoses in order
to ensure functionality, safety and durability.
2. Replace tip.
3. Turn pressure control knob to a lower number.
1. Replace tip, see Tip table on Page 20.
1. Tip is too large for the coating
material which is to be sprayed.
2. Pressure setting incorrect.
3. Volume too low.
4. Coating material viscosity too high.
2. Turn pressure control knob until a satisfactory spraying
pattern is achieved.
3. Clean or replace all filters.
4. Thin out according to the manufacturer’s instructions.
1. Pressure setting too low.
1. Turn pressure control knob clockwise to increase.
F. Poor spray pattern
G. Unit loses power
Digital Electronic Spray Control (DESC) Error Messages
Low Voltage Screen
The Low Voltage screen appears when the
sprayer shuts down because of low input
voltage. Check the power supply and correct
the problem. Restart the sprayer.
The following error message screens appear whenever the Digital Electronic
Spray Control (DESC) detects a problem with the sprayer. Once a problem
occurs and the error message appears, the sprayer will shut down.
Before proceeding, relieve any pressure remaining in the
system (valve position PRIME k). Additionally, follow all
other warnings to reduce the risk of an injection injury,
injury from moving parts or electric shock. Always unplug
the sprayer before servicing!
Check Transducer Screen
The Check Transducer screen appears when
the transducer has become disconnected or
is defective. Take the sprayer to a Wagner
authorized service center for repair.
Check Motor Screen
The Check Motor screen appears when the
motor or motor sensor is defective. Take the
sprayer to a Wagner authorized service center
for repair.
ProSpray 3.39
High Motor Temperature Screen
The High Motor Temperature screen appears
when the temperature of the motor has risen too
high. Take the sprayer to a Wagner authorized
service center for repair.
CHECK
TRANSDUCER
LOW
VOLTAGE
HIGH MOTOR
TEMPERATURE
High Control Temperature Screen
HIGH CONTROL
The High Control Temperature screen appears
TEMPERATURE
when the temperature of the Digital Electronic
Spray Control (DESC) has risen too high. Take
the sprayer to a Wagner authorized service center for repair.
CHECK
MOTOR
High Mechanical Load
HIGH MECHANICAL
The High Mechanical Load screen appears when
LOAD
the sprayer shuts down because of high current
or when the sprayer goes into current fold back
mode. Take the sprayer to a Wagner authorized service center for repair.
15
GB
Servicing
Repairs at the unit
10.Servicing
11.2
10.1
General servicing
Servicing of the unit should be carried out once annually by the
WAGNER service.
1. Check high-pressure hoses, device connecting line and plug
for damage.
2. Check the inlet valve, outlet valve and filter for wear.
10.2
High-pressure hose
Inspect the high-pressure hose visually for any notches or bulges, in
particular at the transition in the fittings. It must be possible to turn
the union nuts freely.
11.
Repairs at the unit
Switch the unit OFF.
Before all repair work: Unplug the power plug from
the outlet.
11.1
Relief valve
1. Use a drift punch of 2 mm to remove the grooved pin (Fig. 13,
Item 1) from the relief valve handle (2).
2. Remove the relief valve handle (2) and cam base (3).
3. Using a wrench, remove the valve housing (4).
4. Ensure that the seal (5) is seated correctly, then screw the new
valve housing (4) completely into the filter block (6). Tighten
securely with a wrench.
5. Align the cam base (3) with the hole in the filter block (6).
Lubricate the cam base with grease and slide on the cam base.
6. Bring the hole in the valve shaft (7) and in the relief valve
handle (2) into alignment.
7. Insert the grooved pin (1) to secure the relief valve handle in
position.
Inlet and outlet valve
1. Remove the four screws in the front cover and then remove
the front cover.
Danger of crushing - do not reach with the fingers or
tool between the moving parts.
2. Turn the pressure control knob to minimum pressure. The
Digi-Trac™ screen should say “PRIME”.
3. Press the #1 key on the Digi-Trac™ control panel. The “CREEP
MODE” screen will now appear.
4. Slowly turn the pressure control knob clockwise to increase
the pressure. The crankshaft/slider assembly will begin to
move very slowly.
5. When it reaches the bottom, dead-center of its stroke, turn
the pressure control knob back to minimum pressure. The
crankshaft/slider assembly should stop.
6. Unplug the power plug from the outlet.
7. Pull off clamp on suction tube and remove return hose.
8. Unscrew the connection hose (Fig. 14, item 1) from the highpressure filter.
9.Turn the knob on the side of the cart clockwise to unlock the
cart. Tilt the cart backwards until it locks into place.
10. Loosen and remove the inlet valve housing (2) from the upper
housing.
11. Remove bearing ring (3), O-ring (4), O-ring (5), inlet valve seat
(6), inlet valve ball (7) and upper ball guide (8).
12. Clean all the parts with the corresponding cleaning agent.
Check the inlet valve housing (2), inlet valve seat (6) and inlet
valve ball (7) for wear and replace the parts if necessary. If the
worn inlet valve seat (6) is unused on one side, install it the
other way around.
8
5
6
4
3
2
7
1
1
7
6
5
4
3
2
13. Screw out outlet valve housing (Fig 15, item 9) from the piston
(10) with 3/8 inch hexagon socket head wrench.
14. Remove the upper seal (11), upper ball guide (12), outlet valve
ball (13), washer (14) and outlet valve seating (15).
16
ProSpray 3.39
GB
14. Remove the adapter (11) and lower packing assembly (12)
from the bottom of the upper housing.
15. Clean all the parts with the corresponding cleaning agent.
Check outlet valve housing (9), outlet valve seat (15), outlet
valve ball (13) and upper ball guide (12) for wear and replace
parts if necessary. If the worn outlet valve seat (15) is unused
on one side, install it the other way around.
16. Carry out installation in the reverse order.
17. If you plan to replace the fluid section packings, move on to
section 11.3. If not, reassemble fluid section in the reverse
order of how it was disassembled.
11
12
13
Repairs at the unit
Be careful not to scratch, score, or otherwise damage
the upper housing during removal of the packings.
14
10
14
15
9
1
7
11.3 Packings
13
8
9
10
1. Remove inlet valve housing in accordance with the steps in
Chapter 11.2, Page 16.
2. It is not necessary to remove the outlet valve.
3. Pull the lever on the underside of the sprayer toward the front
of the sprayer. This will un-clamp the entire fluid section.
4. Slide the fluid section forward to remove it from the gear
housing.
5. Place the fluid section cylinder upright in a vise by clamping
on the wrench flats (Fig. 16, Item 1).
2
3
4
5
12
11
Do not over-tighten the vise. Damage to the cylinder
may occur.
6. Turn the upper housing (2) counterclockwise to loosen it from
the cylinder (3).
7. Slowly pull down the upper housing (2) just far enough to
expose the extension slider (4) and the connecting pin (5) that
connects the piston rod (6) to the extension slider (4).
8. Push the connecting pin out of the extension slider and piston
rod and remove the piston rod and upper housing.
9. Place the upper housing upright in a vise by clamping on the
wrench flats (7).
6
15. Clean the upper housing (2) and cylinder (3-5). Inspect
the upper housing and cylinder for damage and replace if
necessary.
16. Place the upper housing upright (2) in a vise by clamping on
the wrench flats (7).
17. Locate the new upper and lower packings and remove the
pre-form tools. Save the upper packing pre-form tool for use
as the piston insertion tool later in this procedure.
Do not over-tighten the vise. Damage to the upper
housing may occur.
10. Using a wrench, remove the upper seal retainer (Fig. 16, Item
8).
11. Slide the piston rod (6) out through the bottom of the upper
housing (2).
12. Inspect the piston rod (6) for wear and replace if necessary.
13. Remove the upper support ring (9) and upper packing
assembly (10) from the top of the upper housing (2).
ProSpray 3.39
i
Do not remove the pre-form tools from the upper
and lower packings until immediately before they
are installed into the upper housing.
18. Lubricate upper packing (10) and lower packing (12) with
machine grease.
17
GB
Repairs at the unit
26. Insert the piston rod (6) into the bottom of the upper housing
(2), through the lower packing assembly (12), through the
upper packing assembly (10), and out through the upper seal
retainer (8).
19. Insert upper packing (Fig. 17) with O-ring (1) and protruding
lip (2) downward.
1
i
2
27. Remove the piston insertion tool from the top of the piston
rod (6).
28. Lubricate the threads on the upper housing with anti-seize
compound. Remove the upper housing from the vise.
29. Insert the piston rod into the extension slider. When the
connecting pin hole on the piston rod lines up with the hole in
the extension slider, insert the connecting pin.
30. Thread the upper housing into the cylinder, turning clockwise.
31. Continue to turn the upper housing clockwise until it is flush
against the cylinder.
32. Replace the cylinder (3) back into the fluid section clamp on
the gear housing. Make sure to slide the top of the piston rod
extension into the T-slot (13) on the slider assembly (14).
33. Push the lever on the underside of the unit toward the rear of
the sprayer to lock the fluid section back into place.
34. Insert the adapter (Fig. 16, item 11) into the bottom of the
upper housing.
35. Making sure that the bearing ring (Fig. 14, item 3) and O-rings
(Fig. 14, items 4-5) are lubricated and in place, reassemble the
inlet valve assembly and and thread it into the upper housing.
Tighten the inlet valve housing until the o-ring engages,
then continue to tighten until snug. Once snug, tighten an
additional 1/8–1/4 turn.
36. Replace the connection hose to the fitting on the highpressure filter.
37. Replace the return hose into the clamp on the siphon tube.
38. Install front cover.
20. Insert upper support ring (9) on top of the upper packing (10)
21. Thread the upper seal retainer (8) into the upper housing (2).
22. Rotate the upper housing in the vise so that the bottom end is
facing up.
23. Insert the lower packing (Fig. 18) partially into the bottom of
the cylinder with the large beveled edge (1) facing toward the
cylinder (beveled edge will be facing up when the cylinder is
upright).
1
24. Push the lower packing assembly (Fig. 16, Item 12) into
position using the lower packing insertion tool (see Fluid
Section Assembly parts list for lower packing insertion tool
P/N).
i
Coat the piston insertion tool (i.e. upper packing
pre-form tool) and the piston rod with grease before
inserting them into the upper housing.
25. Place the piston insertion tool over the top of the piston rod
(6).
11.4
Make sure the raised lip on the bottom of the lower
packing is fully outside the packing around the
piston rod after insertion of the piston rod.
ProSpray 3.39 connection diagram
Ground
EMI Filter
Blue / White
Switch
Blue / White
Black / Brown
Power Cord
Black /
Brown
P/N 0522052
Blue
P/N 0522053
Green / Yellow
Brown
Fuse block
Green /
Yellow
Black
Black / Brown
Blue / White
White
Green /
Yellow
Ground
Fuse
Black
Capacitor
Black
Red
Motor controller
Red (+)
Ground
Black (-)
White
Blue / White
Hall sensor
White
Potentiometer
Red
Black
Surge suppressor
P/N 0522058
Fan
18
L.E.D.
Display wire
assembly (P/N 0522022)
Pressure sensor
Motor
ProSpray 3.39
GB
Appendix
12.Appendix
12.1
Selection of tip
To achieve faultless and rational working, the selection of the tip is of the greatest importance.
In many cases the correct tip can only be determined by means of a spraying test.
Some rules for this:
The spray jet must be even.
If streaks appear in the spray jet the spraying pressure is either too low or the viscosity of the coating material to high.
Remedy: Increase pressure or dilute coating material. Each pump conveys a certain quantity in proportion to the size of the tip:
The following principle is valid:
large tip = low pressure
small tip = high pressure
There is a large range of tips with various spraying angles.
12.2
Servicing and cleaning of Airless hard-metal tips
Standard tips
If a different tip type has been fitted, then clean it according to manufacturer’s instructions.
The tip has a bore processed with the greatest precision. Careful handling is necessary to achieve long durability. Do not forget the fact that the
hard-metal insert is brittle! Never throw the tip or handle with sharp metal objects.
The following points must be observed to keep the tip clean and ready for use:
1. Turn the relief valve handle fully counterclockwise (k Circulation).
2. Switch off the gasoline engine.
3. Dismount the tip from the spray gun.
4. Place tip in an appropriate cleaning agent until all coating material residue is dissolved.
5. If there is pressure air, blow out tip.
6. Remove any residue by means of a sharp wooden rod (toothpick).
7. Check the tip with the help of a magnifying glass and, if necessary, repeat points 4 to 6.
12.3
Spray gun accessories
Flat jet adjusting tip
up to 250 bar (25 MPa
Tip
marking
Bore mm
Spray width at about 30 cm
removal of spray object
Pressure 100 bar (10 MPa)
15
0.13 - 0.46
5 - 35 cm
Flat jet
adjusting tip
Order No.
Use
0999 057
Paints
20
0.18 - 0.48
5 - 50 cm
Paints, fillers
0999 053
28
0.28 - 0.66
8 - 55 cm
Paints, dispersions
0999 054
41
0.43 - 0.88
10 - 60 cm
Rust protection paints
- dispersions
0999 055
49
0.53 - 1.37
10 - 40 cm
Large-area coats
0999 056
Tip extension
with slewable
knee joint
(without tip)
Contact protection
for the flat jet adjustment tip
Order No. 0097 294
Tip extension
15 cm, F-thread, Order no. 0556 051
15 cm, G-thread, Order no. 0556 074
Length: 100 cm
Order no. 0096 015
30 cm, F-thread, Order no. 0556 052
30 cm, G-thread, Order no. 0556 075
Length: 200 cm
Order no. 0096 016
45 cm, F-thread, Order no. 0556 053
45 cm, G-thread, Order no. 0556 076
Length: 300 cm
Order no. 0096 017
60 cm, F-thread, Order no. 0556 054
60 cm, G-thread, Order no. 0556 077
ProSpray 3.39
19
GB
Appendix
12.4
Airless tip table
Wagner TradeTip 3 tip
up to 270 bar
(27 MPa)
i
without tip
F thread (11/16 - 16 UN)
for Wagner spray guns
Order no. 0289391
without tip
G thread (7/8 - 14 UN)
for Graco/Titan spray guns
Order no. 0289390
All of the tips in the table below are supplied
together with the appropriate gun filter.
Application
Tip marking
Spray
angle
Bore
inch / mm
Spraying
width mm 1)
Gun filter
Order no.
Water-thinnable and solvent-based
paints and varnishes, oils, separating agents
107
207
307
407
109
209
309
409
509
609
10°
20°
30°
40°
10°
20°
30°
40°
50°
60°
0.007 / 0.18
0.007 / 0.18
0.007 / 0.18
0.007 / 0.18
0.009 / 0.23
0.009 / 0.23
0.009 / 0.23
0.009 / 0.23
0.009 / 0.23
0.009 / 0.23
100
120
150
190
100
120
150
190
225
270
red
red
red
red
red
red
red
red
red
red
0553107
0553207
0553307
0553407
0553109
0553209
0553309
0553409
0553509
0553609
Synthetic-resin paints
PVC paints
111
211
311
411
511
611
10°
20°
30°
40°
50°
60°
0.011 / 0.28
0.011 / 0.28
0.011 / 0.28
0.011 / 0.28
0.011 / 0.28
0.011 / 0.28
100
120
150
190
225
270
red
red
red
red
red
red
0553111
0553211
0553311
0553411
0553511
0553611
Paints, primers
Fillers
113
213
313
413
513
613
813
10°
20°
30°
40°
50°
60°
80°
0.013 / 0.33
0.013 / 0.33
0.013 / 0.33
0.013 / 0.33
0.013 / 0.33
0.013 / 0.33
0.013 / 0.33
100
120
150
190
225
270
330
red
red
red
red
red
red
red
0553113
0553213
0553313
0553413
0553513
0553613
0553813
Fillers
Rust protection paints
115
215
315
415
515
615
715
815
10°
20°
30°
40°
50°
60°
70°
80°
0.015 / 0.38
0.015 / 0.38
0.015 / 0.38
0.015 / 0.38
0.015 / 0.38
0.015 / 0.38
0.015 / 0.38
0.015 / 0.38
100
120
150
190
225
270
300
330
yellow
yellow
yellow
yellow
yellow
yellow
yellow
yellow
0553115
0553215
0553315
0553415
0553515
0553615
0553715
0553815
Rust protection paints
Latex paints
Dispersions
117
217
317
417
517
617
717
817
10°
20°
30°
40°
50°
60°
70°
80°
0.017 / 0.43
0.017 / 0.43
0.017 / 0.43
0.017 / 0.43
0.017 / 0.43
0.017 / 0.43
0.017 / 0.43
0.017 / 0.43
100
120
150
190
225
270
300
330
yellow
yellow
yellow
yellow
yellow
yellow
yellow
yellow
0553117
0553217
0553317
0553417
0553517
0553617
0553717
0553817
Rust protection paints
Latex paints
Dispersions
219
319
419
519
619
719
819
919
20°
30°
40°
50°
60°
70°
80°
90°
0.019 / 0.48
0.019 / 0.48
0.019 / 0.48
0.019 / 0.48
0.019 / 0.48
0.019 / 0.48
0.019 / 0.48
0.019 / 0.48
120
150
190
225
270
300
330
385
white
white
white
white
white
white
white
white
0553219
0553319
0553419
0553519
0553619
0553719
0553819
0553919
Flame retardant
221
321
421
521
621
721
821
20°
30°
40°
50°
60°
70°
80°
0.021 / 0.53
0.021 / 0.53
0.021 / 0.53
0.021 / 0.53
0.021 / 0.53
0.021 / 0.53
0.021 / 0.53
120
150
190
225
270
300
330
white
white
white
white
white
white
white
0553221
0553321
0553421
0553521
0553621
0553721
0553821
1)Spray width at about 30 cm to the object and 100 bar (10 MPa) pressure with synthetic-resin paint 20 DIN seconds.
20
ProSpray 3.39
GB
Appendix
Application
Tip marking
Spray
angle
Bore
inch / mm
Spraying
width mm 1)
Gun filter
Order no.
Roof coatings
223
323
423
523
623
723
823
20°
30°
40°
50°
60°
70°
80°
0.023 / 0.58
0.023 / 0.58
0.023 / 0.58
0.023 / 0.58
0.023 / 0.58
0.023 / 0.58
0.023 / 0.58
120
150
190
225
270
300
330
white
white
white
white
white
white
white
0553223
0553323
0553423
0553523
0553623
0553723
0553823
Thick-film materials,
Corrosion protection
Spray filler
225
325
425
525
625
725
825
227
327
427
527
627
827
229
329
429
529
629
231
331
431
531
631
731
831
233
333
433
533
633
235
335
435
535
635
735
439
539
639
20°
30°
40°
50°
60°
70°
80°
20°
30°
40°
50°
60°
80°
20°
30°
40°
50°
60°
20°
30°
40°
50°
60°
70°
80°
20°
30°
40°
50°
60°
20°
30°
40°
50°
60°
70°
40°
50°
60°
0.025 / 0.64
0.025 / 0.64
0.025 / 0.64
0.025 / 0.64
0.025 / 0.64
0.025 / 0.64
0.025 / 0.64
0.027 / 0.69
0.027 / 0.69
0.027 / 0.69
0.027 / 0.69
0.027 / 0.69
0.027 / 0.69
0.029 / 0.75
0.029 / 0.75
0.029 / 0.75
0.029 / 0.75
0.029 / 0.75
0.031 / 0.79
0.031 / 0.79
0.031 / 0.79
0.031 / 0.79
0.031 / 0.79
0.031 / 0.79
0.031 / 0.79
0.033 / 0.83
0.033 / 0.83
0.033 / 0.83
0.033 / 0.83
0.033 / 0.83
0.035 / 0.90
0.035 / 0.90
0.035 / 0.90
0.035 / 0.90
0.035 / 0.90
0.035 / 0.90
0.039 / 0.99
0.039 / 0.99
0.039 / 0.99
120
150
190
225
270
300
330
120
150
190
225
270
330
120
150
190
225
270
120
150
190
225
270
300
330
120
150
190
225
270
120
150
190
225
270
300
190
225
270
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
white
0553225
0553325
0553425
0553525
0553625
0553725
0553825
0553227
0553327
0553427
0553527
0553627
0553827
0553229
0553329
0553429
0553529
0553629
0553231
0553331
0553431
0553531
0553631
0553731
0553831
0553233
0553333
0553433
0553533
0553633
0553235
0553335
0553435
0553535
0553635
0553735
0553439
0553539
0553639
Heavy duty applications
243
443
543
643
445
545
645
451
551
651
252
455
555
655
261
461
561
661
263
463
565
665
267
467
20°
40°
50°
60°
40°
50°
60°
40°
50°
60°
20°
40°
50°
60°
20°
40°
50°
60°
20°
40°
50°
60°
20°
40°
0.043 / 1.10
0.043 / 1.10
0.043 / 1.10
0.043 / 1.10
0.045 / 1.14
0.045 / 1.14
0.045 / 1.14
0.051 / 1.30
0.051 / 1.30
0.051 / 1.30
0.052 / 1.32
0.055 / 1.40
0.055 / 1.40
0.055 / 1.40
0.061 / 1.55
0.061 / 1.55
0.061 / 1.55
0.061 / 1.55
0.063 / 1.60
0.063 / 1.60
0.065 / 1.65
0.065 / 1.65
0.067 / 1.70
0.067 / 1.70
120
190
225
270
190
225
270
190
225
270
120
190
225
270
120
190
225
270
120
190
225
270
120
190
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
green
0553243
0553443
0553543
0553643
0553445
0553545
0553645
0553451
0553551
0553651
0553252
0553455
0553555
0553655
0553261
0553461
0553561
0553661
0553263
0553463
0553565
0553665
0553267
0553467
1)Spray width at about 30 cm to the object and 100 bar (10 MPa) pressure with synthetic-resin paint 20 DIN seconds.
ProSpray 3.39
21
GB
Appendix
12.5Pump-Runner
(Order No. 2306987)
Universal accessories for cleaning, clean transportation and preservation of the pump unit.
Features:
• Simpler cleaning – the cleaning liquid circulates constantly through the pump making thorough cleaning of the interior
• No cleaning necessary during work stoppage or change of location because the paint in the pump cannot dry out or leak
• Better protection
• Simple assembly
Suitable for the following models:
Diaphragm Pumps
SF 21
SF 23
SF 27
SF 31
SF 7000
i
Double-stroke piston pumps
Finish 270/370
Nespray Deco
Nespray 31
PS 24
PS 26
PS 30
PS 34
PS 3.25
PS 3.29
PS 3.31
PS 3.34
Order this at the same time: EasyClean, cleaning and preservation agent (118ml) Order no. 0508 620.
Example of use
22
ProSpray 3.39
A
J. Wagner Ges.m.b.H.
Ottogasse 2/20
2333 Leopoldsdorf
Österreich
Tel. +43/ 2235 / 44 158
Telefax +43/ 2235 / 44 163
office@wagner-group.at
DK
Wagner Spraytech
Scandinavia A/S
Helgeshøj Allé 28
2630 Taastrup
Denmark
Tel. +45/43/ 27 18 18
Telefax +45/43/ 43 05 28
wagner@wagner-group.dk
GB
B
WSB Finishing Equipment
Veilinglaan 56-58
1861 Wolvertem
Belgium
Tel. +32/2/269 46 75
Telefax +32/2/269 78 45
info@wagner-wsb.nl
E
Wagner Spraytech Iberica S.A.
P.O. Box 132, Crta. N-340
08750 Molins de Rey
Barcelona / Espania
Tel. +34/93/6800028
Telefax +34/93/66800555
info@wagnerspain.com
I
Wagner Colora Srl
Via Italia 34
20060 Gessate - MI
Italia
Tel. +39 02.9592920.1
Telefax +39 02.95780187
info@wagnercolora.com
CH
Wagner International AG
Industriestrasse 22
9450 Altstätten
Schweiz
Tel. +41/71 / 7 57 22 11
Telefax +41/71 / 7 57 22 22
wagner@wagner-group.ch
F
Wagner France
12 Avenue des Tropiques
Z.A. de Courtaboeuf,
91978 Les Ulis Cedex
France
Tel. 0 825 011 111
Telefax +33 (0) 69 81 72 57
division.batiment@wagner-france.fr
NL
WSB Finishing Equipment BV
De Heldinnenlaan 200
3543 MB Utrecht
Netherlands
Tel. +31/ 30/241 41 55
Telefax +31/ 30/241 17 87
info@wagner-wsb.nl
D
J. Wagner GmbH
Otto-Lilienthal-Straße 18
D-88677 Markdorf
Postfach 11 20
Deutschland
Tel. +49 / 75 44 / 505-1664
Telefax +49 / 75 44 / 505-1155
wagner@wagner-group.com
www.wagnergroup.com
CZ
Wagner, spol. s r.o.
Nedasovská str. 345
155 21 Praha 5 -Zlicín
Czechia
Tel. +42/ 2 / 579 50 412
Telefax +42/ 2 / 579 51 052
info@wagner.cz
S
Wagner Spraytech
Scandinavia A/S
Helgeshøj Allé 28
2630 Taastrup
Denmark
Tel. +45/43/ 21 18 18
Telefax +45/43/ 43 05 28
wagner@wagner-group.dk
www.wagner-group.com
ProSpray 3.39
23
Wagner Spraytech (UK) Limited
The Coach House
2 Main Road
Middleton Cheney OX17 2ND
Great Britain
UK-Helpline 0844 335 0517
5 p per minute (landline)
Accessories illustration
ProSpray 3.39
2
1
5
3
6
4
7
9
8
10
24
ProSpray 3.39
Item
Part No.
Description
1
0296 388
Spray gun AG 08, F-thread
0296 386
Spray gun AG 08, G-thread
0502 166
Spray gun AG 14, F-thread
2
0502 119
Spray gun AG 14, G-thread
0296 441
Pole gun 120 cm, G-thread 7/8”
0296 443
Pole gun 120 cm, F-thread 11/16”
0296 442
Pole gun 200 cm, G-thread 7/8”
0296 444
Pole gun 200 cm, F-thread 11/16”
3
0345 010
In-line roller IR-100
4
9984 573
High-pressure hose DN 4 mm, 7.5 m with stainless steel nipple, 1/4”
9984 574
High-pressure hose DN 6 mm, 15 m for dispersion, 1/4”
9984 575
High-pressure hose DN 6 mm, 30 m for dispersion, 1/4”
9984 506
High-pressure hose DN 10 mm, 15 m with stainless steel nipple, 3/8”
9984 568
High-pressure hose DN 13 mm, 15 m with stainless steel nipple, 1/2”
9984 567
High-pressure hose DN 10 mm, 2.5 m with stainless steel nipple, 3/8”
0034 038
Double socket for coupling high-pressure hoses (1/4” x 1/4”)
3203 026
Double socket for coupling high-pressure hoses (3/8” x 1/2”)
5
6
0367 561
Socket for coupling 3/8” whip hose to spray gun (1/4” x 3/8”)
7
0034 950
Metex-Reuse
Reuse for pre-filtering of coating material in vessel. Place suction pipe in the reuse.
0034 952
Sieve package (5 pcs) for paint
8
9
10
0034 951
Sieve package (5 pcs) for dispersion
0034 383
Gun filter, red, 1 piece; 180 mesh extra fine
0097 022
Gun filter, red, 10 pieces; 180 mesh extra fine
0043 235
Gun filter, yellow, 1 piece; 100 mesh fine
0097 023
Gun filter, yellow, 10 pieces; 100 mesh fine
0034 377
Gun filter, white, 1 piece; 50 mesh medium
0097 024
Gun filter, white, 10 pieces; 50 mesh medium
0089 323
Gun filter, green, 1 piece; 30 mesh coarse
0097 025
Gun filter, green, 10 pieces; 30 mesh coarse
0097 108
TipClean Cleaning Set for easy cleaning and conservation of nozzles
0508 619
EasyGlide, special oil (118ml)
0508 620
EasyClean, cleaning and conservation agent (118 ml)
2309 956*
Large volume container
2312 157*
Connection kit for large volume container
*Order at the same time
ProSpray 3.39
25
Spare parts list
ProSpray 3.39
Main Assembly
62
59
63
60
64
1
61
2
14
15
16
17
3
18
4
20
19
21
5
6
22
23
24
7
8
BS4343
NEMA 5-15P
0558 599
120V
6m
0290 299
120V
4.6 m
25
26
9
41
34
39
40
10
27
35
28
29
2
36
11
30
12
31
13
32
33
37
51
38
50
52
42
43
44
45
46
53
47
48
49
54
55
56
57
26
58
ProSpray 3.39
Item
Part No.
Description
Item
Part No.
Description
1
0290 271
Motor shroud
2
0508 559
Screw (2)
33
858-625
Screw (2)
34
9805 348
Screw (4)
3
0558 500
Belly pan assembly
35
0290 246
Lever assembly
4
5
9802 266
Screw (2)
36
0290 247
Clevis assembly
0290 228
Door
37
0558 358A
6
0509 218
Screw (2)
38
9850 639
Clip
7
0290 253
Grommit
39
0290 267
Fitting
8
0551 778
Transducer assembly
40
9871 189
O-ring
9
0558 710
Filter assembly
41
9885 615
Fitting
10
0507 785
Return tube
42
0290 252
Control panel cover with label
11
0290 248
Hose
43
0507 749
Nut with seal
12
0507 786
Washer (2)
44
0290 202
Set screw
13
9805 311
Screw (2)
45
0290 218
Knob
14
9802 266
Screw (2)
46
9850 936
Switch
15
0290 225
Electronic cover
47
0508 579
Potentiometer
16
9805 317
Screw (2)
48
0522 007
LED assembly
17
0290 212
Handle cover, back
49
0290 220
18
0290 213
Handle cover, front
Digital Electronic Spray Control (DESC)
display
19
-------
50
0558 493
Power cord jumper*
20
0509 218
51
0558 454
Bracket cover*
21
0558 321A
52
0509 218
Screw (4)*
53
9800 340
Screw (2)*
22
0522 404
Fuse, 20A
54
0551 980
Lock nut (2)*
23
9804 916
Screw
55
0522 424
EMI filter, 20A*
24
0522 210
Mounting plate
56
9805 240
Screw (3)*
25
0290 280
Face plate / oiler assembly
57
0558 453
Bracket*
26
0509 218
Screw (4)
58
0551 714
Cord grip (2)*
27
9812 310
Hex nut (2)
59
9805 400
Screw (2)
28
9894 274
Spring (2)
60
0552 403
Fan
29
0290 259
Retainer
61
0290 475
Belly pan
30
9805 362
Bolt (2)
62
9805 403
Set screw
31
805-434
Pail hook
63
9810 103
Nut
32
9821 503
Washer (2)
64
0524 353
Nut
0522 058
Surge protector (not shown, see
schematic)
0522 054
Arrestor (not shown, see schematic)
0522022
Display wire assembly (not shown, see
schematic)
Drive assembly
Screw (4)
Control panel assembly, complete
(includes items 42-49)
ProSpray 3.39
27
* UK only
Fluid section assembly
Spare parts list
ProSpray 3.39
Fluid section
Item
Part No.
Description
1
0558 419
Cylinder
2
0524 905
Stopping spacer
3
0524 906
Extension bushing
4
0558 570A
Piston extension
5
0558 422
Extension slider
6
9832 126
Connecting pin (2)
7
0290 266
Retainer
8
0290 286
9
------
10
9885 613
Fitting
11
0558 423
Upper housing
12
------
Lower packing
13
0509 511
14
0558 424A
Piston rod
15
0507 734
Upper seal
16
0507 452
Upper ball guide
17
9841 502
Outlet valve ball
18
0507 454
Washer
18
0294 516
Outlet valve seat
20
0507 733
Outlet valve retainer
15
16
17
18
19
21
0558 676
Lower ball guide
22
0555 595
Inlet valve ball
23
00310
Inlet valve seat
24
9871 218
O-ring
20
25
0507 730
O-ring
26
0507 731
O-ring
27
0524 911
Inlet valve housing
28
0555 217
Inlet screen
29
0524 421
Spring clip
30
9822 556
Snap ring
30
31
1
12
2
13
3
14
4
5
6
7
8
32
9
21
10
22
23
24
25
11
26
27
28
Spacer
Upper packing
Adapter
31
9860 727
32
0558 365A
Piston assembly (includes items
14-20)
0558 587
Repacking kit - 1 (includes items
8-9, 12, 15, 17-18, 22 and 24-26)
0558 730
Repacking kit - 2 (includes items
8-9 and 12)
0509 927
Lower packing insertion tool
Bushing
29
28
ProSpray 3.39
Spare parts list
ProSpray 3.39
Drive Assembly
1
4
2
3
5
6
7
8
9
12
10
13
14
11
18
19
20
15
16
17
Item
Part No.
1
0558 572A
2
Description
Item
Part No.
Description
Slider assembly
11
0558 759
Baffle
0507 767
Screw (4)
12
0558 544
Electronic control assembly
3
0290 272
Slider housing
13
0522 027
Capacitor assembly
4
0558 342A
Housing assembly
14
0551 543
Tie wrap
5
0558 362
3rd stage gear
15
9802 266
Screw (2)
6
0558 363
2nd stage gear
16
9822 106
Washer
7
9821 503
Washer (3)
17
0522 040
Wire assembly
8
700-287
Screw (3)
18
0558 559
Grounding strap*
9
0509 218
Screw (4)
19
9822 631
Washer*
10
0558 743A
Motor assembly
20
9800 340
Ground screw (2)*
ProSpray 3.39
29
* UK only
Spare parts list
ProSpray 3.39
Filter assembly
1
15
2
3
4
5
6
7
8
9
10
11
12
13
Item
Part No.
Description
1
0524 918
2
14058
3
14
Item
Part No.
Description
Filter housing
9
0507 745
Gasket
Conical spring
10
0558 727
Bypass valve assembly (includes item 9)
0508 748
Filter, 60 mesh (standard)
11
0507 931
Cam base
0508 451
Filter, 30 mesh
12
0508 744
Relief valve knob
0508 452
Filter, 100 mesh
13
5006 543
Groove pin
4
0508 603
Bearing ring
14
0349 610
Fitting
5
0508 749
Bearing spring
15
0558 668
Filter plug
6
0551 951
O-ring
0507 254
Relief valve kit (includes items 9-13).
7
0509 420
Pipe plug
8
0290 264
Housing
30
ProSpray 3.39
Spare parts list
ProSpray 3.39
Upright cart assembly
1
8
9
19
20
10
2
11
3
12
13
4
14
5
6
15
16
7
15
17
18
Item
Part No.
Description
Item
Part No.
Description
1
805-206A
Handle assembly (includes items 8-9)
11
9820 305
Washer (2)
2
3
9805 352
Screw (2)
12
0555 319
Jam nut
0290 257
Bushing
13
0290 236
Cam assembly
4
805-200
Cart weldment
14
9805 353
Screw (2)
5
9894 275
Spring
15
0294 534
Spacer (4)
6
0290 294
Sleeve
16
0509 624
Wheel (2)
7
0290 285
Carriage assembly
17
800-019
Axle cap (2)
8
0509 386
Washer (4)
18
9885 571
9
0295 608
Screw (4)
19
54458
Screw (2)
10
0279 481
Screw
20
13538
Pad (2)
ProSpray 3.39
31
Plug (2)
GB
Important notes on product liability
As a result of an EC regulation being effective as from January 1, 1990, the
manufacturer shall only be liable for his product if all parts come from him or
are released by him, and if the devices are properly mounted and operated.
If the user applies outside accessories and spare parts, the manufacturer´s
liability can fully or partially be inapplicable; in extreme cases usage of the
entire device can be prohibited by the competent authorities (employer´s
liability insurance association and factory inspectorate division).
Only the usage of original WAGNER accessories and spare parts guarantees
that all safety regulations are observed.
3+2 years guarantee for professional finishing
Wagner professional guarantee
(Status 01.02.2009)
1. Scope of guarantee
All Wagner professional colour application devices (hereafter referred to as
products) are carefully inspected, tested and are subject to strict checks under
Wagner quality assurance. Wagner exclusively issues extended guarantees
to commercial or professional users (hereafter referred to as “customer”)
who have purchased the product in an authorised specialist shop, and which
relate to the products listed for that customer on the Internet under www.
wagner-group.com/profi-guarantee.
The buyer’s claim for liability for defects from the purchase agreement with
the seller as well as statutory rights are not impaired by this guarantee.
We provide a guarantee in that we decide whether to replace or repair
the product or individual parts, or take the device back and reimburse
the purchase price. The costs for materials and working hours are our
responsibility. Replaced products or parts become our property.
2. Guarantee period and registration
The guarantee period amounts to 36 months. For industrial use or equal wear,
such as shift operations in particular, or in the event of rentals it amounts to
12 months.
Systems driven by petrol or air are also guaranteed for a 12 month period.
The guarantee period begins with the day of delivery by the authorised
specialist shop. The date on the original purchase document is authoritative.
For all products bought in authorised specialist shops from 01.02.2009 the
guarantee period is extended to 24 months providing the buyer of these
devices registers in accordance with the following conditions within 4 weeks
of the day of delivery by the authorised specialist shop.
Registration can be completed on the Internet under www.wagner-group.
com/profi-guarantee. The guarantee certificate is valid as confirmation, as
is the original purchase document that carries the date of the purchase.
Registration is only possible if the buyer is in agreement with having the data
being stored that is entered during registration.
When services are carried out under guarantee the guarantee period for the
product is neither extended nor renewed.
Once the guarantee period has expired, claims made against the guarantee or
from the guarantee can no longer be enforced.
3. Handling
If defects can be seen in the materials, processing or performance of the
device during the guarantee period, guarantee claims must be made
immediately, or at the latest within a period of 2 weeks.
The authorised specialist shop that delivered the device is entitled to accept
guarantee claims. Guarantee claims may also be made to the service centres
named in our operating instructions. The product has to be sent without
charge or presented together with the original purchase document that
includes details of the purchase date and the name of the product. In order
to claim for an extension to the guarantee, the guarantee certificate must be
included.
The costs as well as the risk of loss or damage to the product in transit or by
the centre that accepts the guarantee claims or who delivers the repaired
product, are the responsibility of the customer.
32
4. Exclusion of guarantee
Guarantee claims cannot be considered
- for parts that are subject to wear and tear due to use or other natural
wear and tear, as well as defects in the product that are a result of
natural wear and tear, or wear and tear due to use. This includes in
particular cables, valves, packaging, jets, cylinders, pistons, meanscarrying housing components, filters, pipes, seals, rotors, stators, etc.
Damage due to wear and tear that is caused in particular by sanded
coating materials, such as dispersions, plaster, putty, adhesives,
glazes, quartz foundation.
- in the event of errors in devices that are due to non-compliance with
the operating instructions, unsuitable or unprofessional use, incorrect
assembly and/or commissioning by the buyer or by a third party,
or utilisation other than is intended, abnormal ambient conditions,
unsuitable coating materials, unsuitable operating conditions,
operation with the incorrect mains voltage supply/frequency, overoperation or defective servicing or care and/or cleaning.
- for errors in the device that have been caused by using accessory
parts, additional components or spare parts that are not original
Wagner parts.
- for products to which modifications or additions have been carried
out.
- for products where the serial number has been removed or is illegible
- for products to which attempts at repairs have been carried out by
unauthorised persons.
- for products with slight deviations from the target properties, which
are negligible with regard to the value and usability of the device.
- for products that have been partially or fully taken apart.
5. Additional regulations.
The above guarantees apply exclusively to products that have been bought
by authorised specialist shops in the EU, CIS, Australia and are used within the
reference country.
If the check shows that the case is not a guarantee case, repairs are carried
out at the expense of the buyer.
The above regulations manage the legal relationship to us concludingly.
Additional claims, in particular for damages and losses of any type, which
occur as a result of the product or its use, are excluded from the product
liability act except with regard to the area of application.
Claims for liability for defects to the specialist trader remain unaffected.
German law applies to this guarantee. The contractual language is German.
In the event that the meaning of the German and a foreign text of this
guarantee deviate from one another, the meaning of the German text has
priority.
J. Wagner GmbH
Division Professional Finishing
Otto Lilienthal Strasse 18
88677 Markdorf
Federal Republic of Germany
Note on disposal:
In observance of the European Directive 2002/96/
EC on waste electrical and electronic equipment and
implementation in accordance with national law, this
product is not to be disposed of together with household
waste material but must be recycled in an environmentally
friendly way!
Wagner or one of our dealers will take back your used
Wagner waste electrical or electronic equipment and will
dispose of it for you in an environmentally friendly way. Please ask your
local Wagner service centre or dealer for details or contact us direct.
ProSpray 3.39