NVR2000
QUICK INSTALLATION GUIDE
Hardware Installation
Attaching the rack mounting rails to the enclosure
3 Drive Bay Installation/Removal
1 . Secure the short bracket to the front side of
the outer rail w/ 2 screws, and the long bracket
to the rear side of the outer rail w/ 3 screws.
Accessing the Drive Bays
Please power-down the NVR2000 before accessing the drive bays.
2. Repeat the process to install another outer rail.
Warning!
Caution!
Observer all ESD (Electro-static Discharge)
procedure during installation to avoid
damage to the system and other
components.
!
Tools Required
Only qualified server personnel should
install and service this product in order
to avoid risk of injury from electrical
shock and energy hazard.
Use caution when working around the SATA backplane. Do not
touch the backplane with any metal objects and make sure no
ribbon cables touch the backplane. Also, regardless of how
many SATA drives are installed, all four drive carriers must
remain in the chassis to maintain.
Phillips
screwdriver
Flat blade
screwdriver
Mounting a Serial ATA Drive in a Drive Carrier
Anti-static
wrist strap
The SATA drives are mounted in drive carriers to simplify their installation and
removal from the chassis. These carriers also help promote proper airflow for the
system. For this reason, even empty carriers without drives installed must remain in
the chassis.
Accessories
• NVR2000 Network Video Recorder
• Unpacking list
• Quick installation guide
• Client Installation CD/DVD
• Slide Rails
• Slide Bracket
• Cable Tie
• Power Cord
1. Install a new SATA drive into the carrier with the printed circuit board side facing
down so that the mounting holes align with those in the carrier.
Installing the enclosure to the rack
1. Install the server by lining up the rear of the
chassis rails with the front of the rack rails.
2. Secure the drive to the carrier with six screws.
2. Slide the chassis into the rack rails, keeping
the pressure even on both sides (you may have
to depress the locking tabs when inserting).
1 Unpack the subsystem
3. When fully inserted into rack, you should hear a
click sound made by locking tabs.
Preparing for Setup
The box should include two sets of rail assemblies,six rail mounting brackets and the
mounting screws you will need to install the system into the rack.Please check the package
content and follow the instruction below.
Preparing the Disk Drives
2
Rack-Mounting and Preparing Disk Drives
Adjusting the rack mounting rails
The NVR2000 series requires at least two disk drives to be installed, to ensure RAID 1
configuration and to install the NVR OS in the first partition of the first virtual pool.
We recommend you to install the first two drives in slot #1 and #2.
The order of the drives does not matter.
Installing/Removing SATA Drives
1. To remove a carrier,push the release button located beside the drive LEDs.
1. Measure the distance between the front and the rear rack posts.
2. Attach a short bracket to the front side of the right outer rail
and a long bracket to the rear side of the right outer rail.
2. Swing the colored handle fully out and use it to pull the unit straight out.
Slot #1 (left) to #2 (right)
3. Adjust the short and long brackets to match
the rails to rack posts.
PWR
BUSY
MUTE
ATTEN
ESC
SSD
accelerator
vpool1
vpool2
© by Surveon Technology, Inc. All rights reserved.
Q M0 N V R 2 E 2 R 1 1
ENT
vpool3
4 Adding PCI HBA Card
6
Power On
Control Panel
Accessing the Inside of the System
Providing Power
1. Grasp the two handles on either side and pull the unit straight out until it locks (you will
hear a "click").
1. P lug the power cord from the power supply unit into a high-quality power strip that
offersprotection from electrical noise and power surges. It is recommended that you
use an uninterruptible power supply (UPS).
2. Depress the two buttons on the top of the chassis to release the top cover. There is a
large rectangular recess in the middle front of the top cover to help you push the cover
away from you until it stops.
2. Depress the power button on the front of the chassis to power up the system.
3. Lift the top cover from the chassis to gain full access to the inside of the NVR2000.
Power button
Mouse (green)
2
1
Keyboard USB0/1 Ports
(purple)
VGA Port
(Blue)
COM1 Port
(Turquoise)
LAN1/2 Ports
Front Cover
1 Slide the left end of the front cover into the chassis until the two pegs are seated in
the chassis wall.
Release
2 While depressing the tab, insert the right end of the cover into the chassis.
the tab to lock the front cover into place.
The NVR2000 chassis can accommodate one full-size PCI-Express HBA add-on card with
the use of a riser card.
Installing a HBA Add-on Card (Optional)
Making Host Connections
1. After powering down the system,remove the PCI slot shield.
Power
USB/Mouse/Keyboard
LAN
SAS cable
2. Fully seat the riser card into the slot,pushing down with your thumbs evenly on both sides
of the card.Seat the HBA card into the riser card.
3. Finish by using a screw to secure the top of the card shield to the chassis.
The PCI slot shield protects the NVR2000 motherboard and its components from EMI and
aid in proper ventilation,so make sure it is always in place.
1.Ctrl Sta tus
2.C_Dirty
3.Temp.
4.BBU Link
5.Hst Bsy
6.Drv Bsy
BBU Status
S
A
S
HOST-CH0
S
A
S
HOST-CH1
SAS Exp.
CH0 Link
1
4
2
5
3
6
COM1
COM2
CH1 Link
5 Cabling
Make the following connections:
I/O Ports
n
LAN port:to connect the NVR2000 to the Internet
See the figures below for the colors and locations of the various I/O ports.
n
SAS cable: to connect the NVR2000 controller to the storage alley/enclosure
n
Power cable
The USB, VGA, and keyboard ports are provided for local maintenance.
n
(Optional) USB port: to connect external devices such as CD-ROM for recovery
n
(Optional) Mouse and Keyboard
Note:The port numbering sequence on HBA cards on the host computer should match
that on the RAID enclosure, e.g., HBA port0 to RAID ctrl CH0.