Grandstream Networks, Inc.
HT70X Analog Telephone Adaptor
HT701 HT702 HT704
HT701
HT70X User Manual
Firmware Version 1.0.0.18
HT702
HT704
www.grandstream.com
http://esupport.grandstream.com
TABLE OF CONTENTS
HT70X User Manual
WELCOME.................................................................................................................................................... 4
SAFETY COMPLIANCES................................................................................................................................. 4
W ARRANTY.................................................................................................................................................. 4
CONNECT YOUR HT70X ............................................................................................................................. 5
EQUIPMENT PACKAGING............................................................................................................................... 5
CONNECTING THE HT70X ............................................................................................................................ 5
PRODUCT OVERVIEW ................................................................................................................................ 9
SOFTWARE FEATURES OVERVIEW ................................................................................................................ 9
HARDWARE SPECIFICATION ........................................................................................................................ 10
BASIC OPERATIONS ................................................................................................................................ 11
UNDERSTANDING HT70X VOICE PROMPT ................................................................................................... 11
PLACING A PHONE CALL ............................................................................................................................. 12
CALL HOLD ................................................................................................................................................ 13
CALL W AITING ........................................................................................................................................... 13
CALL TRANSFER ........................................................................................................................................ 13
3-W AY CONFERENCING ............................................................................................................................. 14
FAX SUPPORT ........................................................................................................................................... 14
CALL FEATURES ...................................................................................................................................... 15
CONFIGURATION GUIDE ......................................................................................................................... 16
CONFIGURING THE HT70X THROUGH VOICE PROMPTS................................................................................ 16
CONFIGURING THE HT70X VIA W EB BROWSER........................................................................................... 16
IMPORTANT SETTINGS ................................................................................................................................ 17
Preferred VOCODER (Codec) ................................................................................................................ 18
ADVANCED USER CONFIGURATION ............................................................................................................. 20
SAVING THE CONFIGURATION CHANGES ..................................................................................................... 30
REBOOTING THE HT70X FROM REMOTE ..................................................................................................... 30
CONFIGURATION THROUGH A CENTRAL SERVER .......................................................................................... 31
SOFTWARE UPGRADE............................................................................................................................. 32
FIRMWARE UPGRADE THROUGH TFTP/HTTP/HTTPS ................................................................................ 32
INSTRUCTIONS FOR UPLOAD FROM LOCAL DIRECTORY: ............................................................................... 32
INSTRUCTIONS FOR LOCAL FIRMWARE UPGRADE USING TFTP SERVER: ........................................................ 33
CONFIGURATION FILE DOWNLOAD .............................................................................................................. 33
FIRMWARE AND CONFIGURATION FILE PREFIX AND POSTFIX ........................................................................ 33
MANAGING FIRMWARE AND CONFIGURATION FILE DOWNLOAD ..................................................................... 33
RESTORE FACTORY DEFAULT SETTING .............................................................................................. 35
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 2 of 35
Last Updated: 03/2012
TABLE OF FIGURES
HT70X USER MANUAL
FIGURE 1: CONNECTING THE HT70X............................................................................................................................... 5
FIGURE 2: HT70X CONNECTION DIAGRAM ..................................................................................................................... 8
TABLE OF TABLES
HT70X USER MANUAL
TABLE 1: DEFINITIONS OF THE HT70X CONNECTORS ..................................................................................................... 6
TABLE 2: BASIC DEFINITIONS OF THE HT70X LEDS PATTERN ....................................................................................... 6
TABLE 3: ADVANCED DEFINITIONS OF THE HT70X LEDS PATTERN ............................................................................... 7
TABLE 4: HT70X SOFTWARE FEATURES ......................................................................................................................... 9
TABLE 5: HT70X HARDWARE AND TECHNICAL SPECIFICATIONS.................................................................................. 10
TABLE 6: HT70X IVR MENU DEFINITIONS ................................................................................................................... 11
TABLE 7: HT70X CALL FEATURES ................................................................................................................................ 15
TABLE 8: BASIC SETTINGS ............................................................................................................................................. 18
TABLE 9: STATUS PAGE ................................................................................................................................................. 19
TABLE 10: ADVANCED SETTINGS .................................................................................................................................. 20
TABLE 11: ACCOUNT SETTINGS ..................................................................................................................................... 24
TABLE 12: HT704 FXS PORTS SETTINGS ...................................................................................................................... 30
CONFIGURATION GUI INTERFACE EXAMPLES
HT70X USER MANUAL
(http://www.grandstream.com/products/ht_series/ht70x/documents/ht70x_gui.zip)
1. SCREENSHOT OF ADVANCED USER CONFIGURATION PAGE
2. SCREENSHOT OF BASIC SETTINGS CONFIGURATION PAGE
3. SCREENSHOT OF FXS PORT CONFIGURATION
4. SCREENSHOT OF STATUS PAGE
5. SCREENSHOT OF LOGIN PAGE
6. SCREENSHOT OF REBOOT PAGE
7. SCREENSHOT OF REBOOTING PAGE
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 3 of 35
Last Updated: 03/2012
WELCOME
Thank you for purchasing Grandstream‟s HT70X, the affordable, feature rich Analog Telephone Adaptor.
Grandstream HandyTone70X is a new addition to the popular HandyTone ATA product family. It features
the rich audio quality, a broad range of voice codecs, and functionality including one independent SIP
account per FXS port.
This manual will help you learn how to operate and manage your HandyTone70X Analog Telephone
Adaptor and make the best use of its many upgraded features including simple and quick installation, 3way conferencing, direct IP-IP Calling, and new provisioning support among other features. This HT70X is
very easy to manage and configure, and is specifically designed to be an easy to use and affordable VoIP
solution for both the residential user and the teleworker.
Safety Compliances
The HT70X phone complies with FCC/CE and various safety standards. The HT70X power adaptor is
compliant with UL standard. Only use the universal power adapter provided with the HT70X package. The
manufacturer‟s warranty does not cover damages to the phone caused by unsupported power adaptors.
Warranty
If you purchased your HT70X from a reseller, please contact the company where you purchased your
device for replacement, repair or refund. If you purchased the product directly from Grandstream, contact
your Grandstream Sales and Service Representative for a RMA (Return Materials Authorization) number
before you return the product. Grandstream reserves the right to remedy warranty policy without prior
notification.
Caution: Changes or modifications to this product not expressly approved by Grandstream, or operation
of this product in any way other than as detailed by this User Manual, could void your manufacturer
warranty. Please do not use a different power adaptor with the HT70X as it may cause damage to the
products and void the manufacturer warranty.


This document contains links to HT70X GUI Interfaces. Please download these examples for your
reference here:
http://www.grandstream.com/products/ht_series/ht70x/documents/ht70x_gui.zip
This document is subject to change without notice. The latest electronic version of this user
manual is available for download at:
http://www.grandstream.com/products/ht_series/ht70x/documents/ht70x_usermanual_english.pdf
Reproduction or transmittal of the entire or any part, in any form or by any means, electronic or print, for
any purpose is not permitted without the express written permission of Grandstream Networks, Inc.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 4 of 35
Last Updated: 03/2012
CONNECT YOUR HT70X
Equipment Packaging
The HT70X ATA package contains:




One HT70X Main Case
One Universal Power Adaptor
One Ethernet Cable
One Vertical Stand (Only on HT702 and HT704 Packages)
Connecting the HT70X
The HT70X is designed for easy configuration and easy installation. Configure the HT70X following the
directions in the Configuration section of this manual.
1. Insert a standard RJ11 telephone cable into the Phone port and connect the other end of the
telephone cable to a standard touch-tone analog telephone.
2. Insert the Ethernet cable into the Internet or LAN port of the HT70X and connect the other end of
the Ethernet cable to an uplink port (a router or a modem, etc.)
3. Insert the power adapter into the HT70X and connect it to a wall outlet.
The HT70X Analog Telephone Adaptor is an all-in-one VoIP integrated device designed to be a total
solution for networks providing VoIP services. The HT70X VoIP features and functions are available using
a regular analog telephone.
Figure 1: Connecting the HT70X
HT-701
Display LEDs
(green)
Grandstream Networks, Inc.
Internet Port
(RJ-45 connector
10/100 Mbps)
HT-70X User Manual
Firmware Version 1.0.0.18
Phone
(RJ-11 FXS Ports)
Reset
Power
Supply
(12V;0.5A)
Page 5 of 35
Last Updated: 03/2012
HT702
HT704
Display LED’s (green)
Display LED’s (green)
LAN Port
(RJ-45 connector Reset
10/100 Mbps )
Power
Supply
(12V;1A)
LAN Port
(RJ-45 connector
10/100 Mbps
with LEDS)
Phone (RJ-11
FXS Ports)
Reset
Power
Supply
(12V;1A)
Phone (RJ-11
FXS Ports)
Table 1: Definitions of the HT70X Connectors
DC 12V
Power adapter connection
Internet Port (RJ-45)
Connect to the internal LAN network. (HT701 Only)
LAN Port (RJ-45)
Connect to the internal LAN network. (HT702 and HT704 Only)
RESET
Factory Reset button: Press for 7 seconds to reset factory default settings.
Phone Port(s) (RJ-11)
FXS port: to be connected to analog phones / fax machines.
There are four (4) LED buttons that help you manage the status of your HandyTone 701, and
there are five (5) LED buttons that help you manage the status of your HandyTone 702 and 704.
Table 2: Basic Definitions of the HT70X LEDs Pattern
LEDs
POWER LED
Internet LED
Link/Activity LED
PHONE LED
Indicates Power. Remains ON when power is connected
Indicates Access to Internet. Remains ON while there is Access (HT701 and HT702 Only)
Indicates if There is Activity on the Internet Port (HT701 and HT702 Only)
Indicate status of the respective FXS Ports-PHONE on the back panel
Unregistered – OFF
Registered and Available – ON (Solid Green)
Off-Hook / Busy – Blinking every second
Slow blinking FXS LEDs indicates voicemail
NOTE: All LEDs display green when ON
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 6 of 35
Last Updated: 03/2012
Table 3: Advanced Definitions of the HT70X LEDs Pattern
Patten
Number
Condition
LED-01
LED-02
LED-15
LED-16
LED-17
Device has normal power
Power Error: Power is removed from the device or power
supply with improper voltage is plugged in
Line X is registered normally to the sip providers network
and is ready to make a call
Voice mail waiting for Line X
Device has normal WAN connection and has obtained IP
address
Internet link error: Device is powered up and ready to
connect to the Internet but the WAN/INTERNET port is
down
Internet DHCP Error: Device is properly connected but it is
unable to retrieve an IP address from the device it is
connected to
Line Registration failed: Device is properly setup, can
connect to provider's network, but cannot register to
provider's SIP proxy (no 200 OK)
Device is connected (has physical data link) but there are
incorrect network settings typically associated with PPPoE
connection failure
Hazardous potential test failed: Hazardous AC or DC
voltage is present on the tip and ring or both signals of
phone line X
Foreign electro Motive Force (EMF) Test fail. Foreign
voltage is present on the tip, ring or both signals of phone
line. Device has detected additional external Phone
voltage on the FXS phone line.
Resistive fault test failed. Either tip or ring is shorted to
ground or they are shorted to each other.
Receiver off hook test fail. One or more phones are off
hook on phone line during test.
REN test failed – high REN detected. Too many parallel
phones connected to phone line X
Line is active
Line inactive
During Provisioning Stage*
LED-18
During Firmware Recovery Stage*
LED-03
LED-04
LED-05
LED-06
LED-07
LED-08
LED-09
LED-10
LED-11
LED-12
LED-13
LED-14
LED
LED Behavior
Power
ON
Power
OFF
Phone
ON
Phone
1sec ON / 3sec OFF
Internet
ON
Internet
OFF
Internet
0.25sec ON/ 0.25sec OFF
Phone
OFF
Internet
0.25sec ON/ 0.25sec OFF
Phone
0.25sec ON/ 0.25sec OFF
Phone
0.25sec ON/ 0.25sec OFF
Phone
0.25sec ON/ 0.25sec OFF
Phone
0.25sec ON/ 0.25sec OFF
Phone
0.25sec ON/ 0.25sec OFF
Phone
Phone
Internet /
Phone
Internet /
Phone
1 sec ON/ 1 sec OFF
ON
0.2sec ON/ 0.2sec OFF
0.4sec ON/ 0.4sec OFF
*Note: In Provisioning and Firmware Recovery Stage, the power LED is Steady ON.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 7 of 35
Last Updated: 03/2012
Figure 2: HT70X Connection Diagram
Cordless
Phone
FXS
LAN
Internet
ADSL/Cable
Modem Ethernet
HT701/702/704
Analog
Phone
Fax
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 8 of 35
Last Updated: 03/2012
PRODUCT OVERVIEW
The HT70X is a full feature voice and fax-over IP device that offers a high-level of integration including a
10M/100Mbps network port and one FXS telephone port, market-leading sound quality, rich functionalities,
and a compact and lightweight design. The VoIP network signaling protocol supported is SIP. The HT70X
is fully compatible with SIP industry standard and can interoperate with many other SIP compliant devices
and software on the market. Moreover, it supports comprehensive voice codecs including G.711 (a/µ-law),
G.723.1, G.726-32, G.729 and iLBC.
Software Features Overview

Supports Voice Codecs:

G.711 (a/µ-law), G.723.1, G.726-32, G.729 and iLBC.

T.38 Fax

Comprehensive Dial Plan support for Outgoing calls.

G.168 Echo Cancellation

Voice Activation Detection (VAD), Comfort Noise Generation (CNG), and Packet Loss
Concealment (PLC)

Supports PSTN/PBX analog telephone sets
Table 4: HT70X Software Features
HT 701
Telephone Interfaces
1 FXS ports
HT 702
HT 704
2 FXS ports
4 FXS ports
SIP Provisioning
1 Sip Account, 1 Profile
2 Sip Accounts, 2 Profiles
4 Sip Accounts, 2 Profiles
Number of
Concurrent Calls
1 Concurrent Call
2 Concurrent Calls
4 Concurrent Calls
Voice over Packet
Capabilities
Voice Activity Detection (VAD) with CNG (comfort noise generation) and PLC (packet loss
concealment), Dynamic Jitter Buffer, Modem detection & auto-switch to G.711, Packetized
Voice Protocol Unit (supports RTP/RTCP protocol), G.168 compliant Echo Cancellation,
LEC (line echo cancellation) with NLP, Asymmetric RTP stream
Voice Compression
G.711 + Annex I (PLC), Annex II (VAD/CNG format) encoder and decoder, G.723.1, G.72632(ADPCM), G.729, iLBC, G.726-32 provides proprietary VAD, CNG, and signal power
estimation, Voice Play Out unit (reordering, fixed and adaptive jitter buffer, clock
synchronization), AGC (automatic gain control), Status output, Decoder controlling via voice
packet header
DHCP Server/Client
Yes, DHCP Client only
Telnet Server
Fax over Ip
Yes
T.38 compliant Group 3 Fax Relay up to 14.4kpbs and auto-switch to G.711 for Fax Passthrough, Fax Datapump V.17, V.19, V.27ter, V.29 for T.38 fax relay
QoS
Diffserve, TOS, 802.1 P/Q VLAN tagging
Transport Protocol
DTMF Method
RTP/RTCP
Flexible DTMF transmission method, user interface of In-audio, RFC2833, and/or SIP Info
IP Signaling
SIP (RFC 3261)
Provisioning
TFTP, HTTP, HTTPS, TR-069, XML
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 9 of 35
Last Updated: 03/2012
Control
TLS/SIPS , SIP over TCP/TLS
Device Management
Web interface or via secure encrypted AES or non-encrypted central configuration file for
mass deployment using Grandstream binary file or xml format. Auto/manual provisioning
system or via built-in IVR.
NAT-friendly remote software upgrade (via TFTP/HTTP/HTTPS) for deployed devices
including behind firewall/NAT. Syslog support. Full support of TR-069 management protocol
and Telnet access.
Dial Plan
Yes
Caller ID
Bellcore Type 1 & 2, ETSI, BT, NTT, and DTMF-based CID
Call Handling
Features
Caller ID display or block, Call waiting caller ID, Call waiting/flash, Call transfer, hold,
forward, 3-way conferencing, message waiting, Do-Not-Disturb (DND), call-return service
Hardware Specification
The table below lists the Hardware and Technical specification of HT70X.
Table 5: HT70X Hardware and Technical Specifications
Telephone
Interfaces
Network
Interface
LED Indicators
HT701
HT702
HT704
1 RJ11 FXS port
2 RJ11 FXS ports
4 RJ11 FXS ports
POWER, INTERNET,
LINK/ACTIVITY,
PHONE1, PHONE2
POWER, INTERNET,
LINK/ACTIVITY, PHONE
Factory Reset
Button
POWER, PHONE1, PHONE2,
PHONE3, PHONE4
Yes
Universal
Switching
Power Adaptor
Input: 100–240 VAC/50-60 Hz
0.18A Max
Output: 12VDC, 1A, UL certified
Input: 100–240 VAC/50-60 Hz 0.18A Max
Output: 12VDC, 0.5A, UL certified
o
o
o
o
Operational: 32 –104 F or 0 –40 C
o
o
o
o
Storage: 14 –140 F or -10 –60
Humidity: 10–90% Non-condensing
Environmental
Dimensions
(H x W x D)
Short Haul Loop
1 RJ45 10/100 Mb Base-TX,
Full Duplex port with
connectivity LEDs
1 RJ45 10/100 Mb Base-TX, Full Duplex
26 x 65 x 86mm
28 x 115 x 75mm
5REN, Up to 1Km on 24 AWG
wire
Polarity
Reversal / Wink
EMC
Safety
28 x 115 x 75mm
3REN: Up to 1Km on 24 AWG line
Yes
FCC part15 Class B, EN55022, EN55024, CISPR22, and CISPR24
EN60950-1 & UL60950-1 (UL only for PSU)
Compliance
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 10 of 35
Last Updated: 03/2012
BASIC OPERATIONS
Understanding HT70X Voice Prompt
HT70X has a built-in voice prompt menu for simple device configuration. The IVR menu and the LED
button work with any of the FXS port. Pick up the handset and dial “***” to use the IVR menu.
Table 6: HT70X IVR Menu Definitions
Menu
Voice Prompt
Options
Main Menu
“Enter a Menu Option”
Press “*” for the next menu option
Press “#” to return to the main menu
Enter 01-05, 07,10, 13-17,47 or 99 menu options
01
“DHCP Mode”,
“Static IP Mode”
Press “9” to toggle the selection
If using “Static IP Mode”, configure the IP address information using
menus 02 to 05.
If using “Dynamic IP Mode”, all IP address information comes from
the DHCP server automatically after reboot.
02
“IP Address “ + IP address
The current WAN IP address is announced
If using “Static IP Mode”, enter 12 digit new IP address. You need to
reset the HT for the new IP address to take Effect.
03
“Subnet “ + IP address
Same as menu 02
04
“Gateway “ + IP address
Same as menu 02
05
“DNS Server “ + IP address
Same as menu 02
07
Preferred Vocoder
Press “9” to move to the next selection in the list:

PCM U / PCM A

iLBC

G-726

G-723

G-729
10
“MAC Address”
Announces the Mac address of the unit.
13
Firmware Server IP
Address
Announces current Firmware Server IP address. Enter 12 digit new
IP address.
14
Configuration Server IP
Address
Announces current Config Server Path IP address. Enter 12 digit
new IP address.
15
Upgrade Protocol
Upgrade protocol for firmware and configuration update. Press “9” to
toggle between TFTP / HTTP / HTTPS
16
Firmware Version
Firmware version information.
17
Firmware Upgrade
Firmware upgrade mode. Press “9” to toggle among the following
three options:
- always check
- check when pre/suffix changes
- never upgrade
47
“Direct IP Calling”
Enter the target IP address to make a direct IP call, after dial tone.
(See “Make a Direct IP Call”.)
86
Voice Mail
Number of Voice Mails
99
“RESET”
Press “9” to reboot the device
Enter MAC address to restore factory default setting
(See Restore Factory Default Setting section)
“Invalid Entry”
Automatically returns to main menu
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 11 of 35
Last Updated: 03/2012
“Device not registered”
This prompt will be played immediately after off hook If the device is
not register and the option “Outgoing Call without Registration” is in
NO
Five Success Tips when using the Voice Prompt
1. “*” shifts down to the next menu option
2. “#” returns to the main menu
3. “9” functions as the ENTER key in many cases to confirm or toggle an option
4. All entered digit sequences have known lengths - 2 digits for menu option and 12 digits for IP
address. For IP address, add 0 before the digits if the digits are less than 3 (i.e. - 192.168.0.26
should be key in like 192168000026. No decimal is needed).
5. Key entry cannot be deleted but the phone may prompt error once it is detected
Placing a Phone Call
Phone or Extension Numbers
1. Dial the number directly and wait for 4 seconds (Default “No Key Entry Timeout”); or
2. Dial the number directly and press # (Use # as dial key” must be configured in web configuration).
Examples:
1. Dial an extension directly on the same proxy, (e.g. 1008), and then press the # or wait for 4 seconds.
2. Dial an outside number (e.g. (626) 666-7890), first enter the prefix number (usually 1+ or international
code) followed by the phone number. Press # or wait for 4 seconds. Check with your VoIP service
provider for further details on prefix numbers.
Direct IP Calls
Direct IP calling allows two parties, that is, a FXS Port with an analog phone and another VoIP Device, to
talk to each other in an ad hoc fashion without a SIP proxy.
Elements necessary to completing a Direct IP Call:
1. Both HT70X and other VoIP Device, have public IP addresses, or
2. Both HT70X and other VoIP Device are on the same LAN using private IP addresses, or
3. Both HT70X and other VoIP Device can be connected through a router using public or private IP
addresses (with necessary port forwarding or DMZ).
HT70X supports two ways to make Direct IP Calling:
Using IVR
1. Pick up the analog phone then access the voice menu prompt by dial “***”
2. Dial “47” to access the direct IP call menu
3. Enter the IP address after the dial tone and voice prompt “Direct IP Calling”
Using Star Code
1. Pick up the analog phone then dial “*47”
2. Enter the target IP address.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 12 of 35
Last Updated: 03/2012
Note: NO dial tone will be played between step 1 and 2.
Destination ports can be specified using “*” (encoding for “:”) followed by the port number.
Examples of Direct IP Calls:
a) If the target IP address is 192.168.0.160, the dialing convention is
*47 or Voice Prompt with option 47, then 192*168*0*160.
followed by pressing the “#” key if it is configured as a send key or wait 4 seconds. In this case, the
default destination port 5060 is used if no port is specified.
b) If the target IP address/port is 192.168.1.20:5062, then the dialing convention would be:
*47 or Voice Prompt with option 47, then 192*168*0*160*5062 followed by pressing the “#” key
if it is configured as a send key or wait for 4 seconds.
NOTE: When completing direct IP call, the “Use Random Port” should set to “NO”. You cannot make
direct IP calls between FXS1 to FXS2 since they are using same IP.
Call Hold
Place a call on hold by pressing the “flash” button on the analog phone (if the phone has that button).
Press the “flash” button again to release the previously held Caller and resume conversation. If no “flash”
button is available, use “hook flash” (toggle on-off hook quickly). You may drop a call using hook flash.
Call Waiting
Call waiting tone (3 short beeps) indicates an incoming call, if the call waiting feature is enabled. Toggle
between incoming call and current call by pressing the “flash” button. First call is placed on hold. Press
the “flash” button to toggle between two active calls.
Call Transfer
Blind Transfer
Assume that call Caller A and B are in conversation. A wants to Blind Transfer B to C:
3. Caller A presses FLASH on the analog phone to hear the dial tone.
4. Caller A dials *87 then dials caller C‟s number, and then # (or wait for 4 seconds)
5. Caller A will hear the confirm tone. Then, A can hang up.
NOTE: “Enable Call Feature” must be set to “Yes” in web configuration page.
Caller A can place a call on hold and wait for one of three situations:
1. A quick confirmation tone (similar to call waiting tone) followed by a dial-tone. This indicates the
transfer is successful (transferee has received a 200 OK from transfer target). At this point, Caller
A can either hang up or make another call.
2. A quick busy tone followed by a restored call (on supported platforms only). This means the
transferee has received a 4xx response for the INVITE and we will try to recover the call. The busy
tone is just to indicate to the transferor that the transfer has failed.
3. Continuous busy tone. The phone has timed out.
Note: continuous busy tone does not indicate the transfer has been successful, nor does it indicate
the transfer has failed. It often means there was a failure to receive second NOTIFY – check firmware
for most recent release.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 13 of 35
Last Updated: 03/2012
Attended Transfer
Assume that Caller A and B are in conversation. Caller A wants to Attend Transfer B to C:
1. Caller A presses FLASH on the analog phone for dial tone.
2. Caller A then dials Caller C‟s number followed by # (or wait for 4 seconds).
3. If Caller C answers the call, Caller A and Caller C are in conversation. Then A can hang up to
complete transfer.
4. If Caller C does not answer the call, Caller A can press “flash” to resume call with Caller B.
NOTE: When Attended Transfer fails and A hangs up, the HT70X will ring back user A to remind A that B
is still on the call. A can pick up the phone to resume conversation with B.
3-Way Conferencing
The HT701/702/704 supports Bellcore style 3-way Conference.
Instructions for 3-way conference:
Assume that call party A and B are in conversation. Caller A(HT70X) wants to bring third Caller C into
conference:
1. A presses FLASH (on the analog phone, or Hook Flash for old model phones) to get a dial tone.
2. A dials C‟s number then # (or wait for 4 seconds).
3. If C answers the call, then A presses FLASH to bring B, C in the conference.
4. If C does not answer the call, A can press FLASH back to talk to B.
5. If A presses FLASH during conference, C will be dropped out.
6. If A hangs up, the conference will be terminated for all three parties when configuration “Transfer
on Conference Hang up” is set to “No”. If the configuration is set to “Yes”, A will transfer B to C so
that B and C can continue the conversation.
Fax Support
HT70X supports FAX in two modes: 1) T.38 (Fax over IP) and 2) fax pass through. T.38 is the preferred
method because it is more reliable and works well in most network conditions. If the service provider
supports T.38, please use this method by selecting Fax mode to be T.38 (default). If the service provider
does not support T.38, pass-through mode can be used.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 14 of 35
Last Updated: 03/2012
CALL FEATURES
The HT70X supports all the traditional and advanced telephony features.
Table 7: HT70X Call Features
Key
*02
*03
*16
*17
*30
*31
*47
*50
*51
*67
*82
*69
*70
*71
*72
*73
*74
*78
*79
*87
*90
*91
*92
*93
Flash/Hook
#
Call Features
Forcing a Codec (per call) *027110 (PCMU), *027111 (PCMA), *02723 (G723), *02729 (G729),
*0272616 (G726-r16), *0272624 (G724-r24), *0272632 (G726-r32), *0272640 (G726-r40),
*027201 (iLBC)
Disable LEC (per call) Dial “*03” + ” number ”. No dial tone is played in the middle.
Enable SRTP
Disable SRTP
Block Caller ID (for all subsequent calls)
Send Caller ID (for all subsequent calls)
Direct IP Calling. Dial “*47” + “IP address”. No dial tone is played in the middle. Detail see Direct
IP Calling section on page 12.
Disable Call Waiting (for all subsequent calls)
Enable Call Waiting (for all subsequent calls)
Block Caller ID (per call). Dial “*67” + ” number ”. No dial tone is played in the middle.
Send Caller ID (per call). Dial “*82” + ” number ”. No dial tone is played in the middle.
Call Return Service: Dial *69 and the phone will dial the last incoming phone number received.
Disable Call Waiting (per call). Dial “*70” + ” number ”. No dial tone is played in the middle.
Enable Call Waiting (per call). Dial “*71” + ” number ”. No dial tone is played in the middle.
Unconditional Call Forward: Dial “*72” and then the forwarding number followed by “#”. Wait for
dial tone and hang up. (dial tone indicates successful forward)
Cancel Unconditional Call Forward. To cancel “Unconditional Call Forward”, dial “*73”, wait for
dial tone, then hang up.
Enable Paging Call: Dial “*74” and then the destination phone number you want to page.
Enable Do Not Disturb (DND): When enabled all incoming calls are rejected.
Disable Do Not Disturb (DND): When disabled, incoming calls are accepted.
Blind Transfer
Busy Call Forward: Dial “*90” and then the forwarding number followed by “#”. Wait for dial tone
then hang up.
Cancel Busy Call Forward. To cancel “Busy Call Forward”, dial “*91”, wait for dial tone, then
hang up.
Delayed Call Forward. Dial “*92” and then the forwarding number followed by “#”. Wait for dial
tone then hang up.
Cancel Delayed Call Forward. To cancel Delayed Call Forward, dial “*93”, wait for dial tone,
then hang up.
Toggles between active call and incoming call (call waiting tone). If not in conversation, flash/hook
will switch to a new channel for a new call.
Pressing pound sign will serve as Re-Dial key.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 15 of 35
Last Updated: 03/2012
CONFIGURATION GUIDE
Configuring the HT70X through Voice Prompts
DHCP MODE
Select voice menu option 01 to enable HT70X to use DHCP.
STATIC IP MODE
Select voice menu option 01 to enable HT70X to use STATIC IP mode, then use option 02, 03, 04, 05 to
set up IP address, Subnet Mask, Gateway and DNS server respectively.
FIRMWARE SERVER IP ADDRESS
Select voice menu option 13 to configure the IP address of the firmware server.
CONFIGURATION SERVER IP ADDRESS
Select voice menu option 14 to configure the IP address of the configuration server.
UPGRADE PROTOCOL
Select voice menu option 15 to choose firmware and configuration upgrade protocol. User can choose
between TFTP and HTTP.
FIRMWARE UPGRADE MODE
Select voice menu option 17 to choose firmware upgrade mode among the following three options:
1) Always check, 2) check when pre/suffix changes, and 3) never upgrade.
Configuring the HT70X Via Web Browser
HT70X has an embedded Web server that will respond to HTTP GET/POST requests. It also has
embedded HTML pages that allow users to configure the HT70X through a web browser such as
Microsoft‟s IE, AOL‟s Netscape or Mozilla Firefox installed on Windows or Unix OS. (Macintosh OS is not
included).
Access the Web Configuration Menu
1.
Find the IP address of the HT70X using voice prompt menu option 02.
2. Open a web browser, type the IP address. You will see the log in page of the device.
Note:
•
The IVR announces 12 digits IP address, you need to strip out the leading “0” in the IP address.
For ex. IP address: 192.168.001.014, you need to type in http://192.168.1.14 in the web browser.
Once the HTTP request is entered and sent from a web browser, the user will see a log-in screen. There
are two default passwords for the login page:
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 16 of 35
Last Updated: 03/2012
User Level:
Password:
Web pages allowed:
End User Level
123
Only Status and Basic Settings
Administrator Level
admin
Browse all pages
The password is case sensitive with maximum length of 25 characters. The factory default password for
End User and administrator is “123” and “admin” respectively. Only an administrator can access the
“ADVANCED SETTING”, “FXS PORTs” configuration pages. Please reference the GUI pages using the
following link: http://www.grandstream.com/products/ht_series/HT70x/documents/HT70x_gui.zip .
NOTE: If you cannot log into the configuration page by using the default password, please check with the
VoIP service provider. It is most likely the VoIP service provider has provisioned the device and configured
for you therefore the password has already been changed.
Important Settings
The end-user must configure the following settings according to the local environment.
NOTE: Most settings on the web configuration pages are set to the default values.
NAT Settings
If you plan to keep the Handy Tone within a private network behind a firewall, we recommend using STUN
Server. The following three (3) settings are useful in the STUN Server scenario:
1. STUN Server (under Advanced Settings webpage)
Enter a STUN Server IP (or FQDN) that you may have, or look up a free public STUN Server on the
internet and enter it on this field. If using Public IP, keep this field blank.
2. Use Random Ports (under Advanced Settings webpage)
This setting depends on your network settings. Generally if you have multiple IP devices under the
same network, it should be set to Yes. If using a Public IP address, set this parameter to No.
3. NAT Traversal (under the FXS/Profile web page)
Set this to Yes when gateway is behind firewall on a private network.
DTMF Methods
DTMF Settings are in FXS portX/ProfileX page.

DTMF in-audio

DTMF via RTP (RFC2833)

DTMF via SIP INFO
Set priority of DTMF methods according to your preference. This setting should be based on your server
DTMF setting.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 17 of 35
Last Updated: 03/2012
PREFERRED VOCODER (CODEC)
The HT70X supports a broad range of voice codecs. Under Profile web pages, choose your preferred
order of different codecs:

PCMU/A (or G711µ/a)

G729 A/B/E

G723.1

G726 (16/24/32/40)

iLBC
Table 8: Basic Settings
End User Password
Password to access the Web Configuration Menu. This field is case sensitive with a
maximum length of 25 characters.
Web Port
By default, HTTP uses port 80. This field is for customizable web port.
Telnet Server
Default is set to YES.
IP Address
There are two modes to operate the HT70X:
DHCP mode: all the field values for the Static IP mode are not used (even though they
are still saved in the Flash memory.) The HT701 acquires its IP address from the first
DHCP server it discovers from the LAN it is connected. Using the PPPoE feature: set the
PPPoE account settings. The HT70x will establish a PPPoE session if any of the PPPoE
fields is set.
Static IP mode: configure the IP address, Subnet Mask, Default Router IP address,
DNS Server 1 (primary), DNS Server 2 (secondary) fields. These fields are set to zero by
default.
DHCP hostname
Default is blank. This option specifies the name of the client. This field is optional but may
be required by some Internet Service Providers.
DHCP domain
Default is blank. This option specifies the domain name that client should use when
resolving hostnames via the Domain Name System.
DHCP vendor class ID
Default is HT7XX. Used by clients and servers to exchange vendor-specific information..
PPPoE account ID
PPPoE username. Necessary if ISP requires you to use a PPPoE (Point to Point Protocol
over Ethernet) connection.
PPPoE password
PPPoE account password.
PPPoE Service Name
Default is blank. This field is optional. If your ISP uses a service name for the PPPoE
connection, enter the service name here.
Preferred DNS server
The preferred DNS Server to be used
Time Zone
Controls how the date/time is displayed according to the specified time zone.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 18 of 35
Last Updated: 03/2012
Self-Defined Time Zone
The syntax is std offset dst [offset],start[/time],end[/time]
Default is set to : MTZ+6MDT+5,M3.2.0,M11.1.0
MTZ+6MDT+5,
Time zone with 6 hours offset with 1 hour ahead which is the US central time. It is positive
(+) if the local time zone is west of the Prime Meridian and negative (-) if it is east.
Prime Meridian (a.k.a: International or Greenwich Meridian)
M3.2.0,M11.1.0
st
The 1 number indicates Month: 1,2,3,..,12 (for Jan, Feb, .., Dec)
nd
th
The 2 number indicates the n iteration of the weekday: (1st Sunday, 3rd Tuesday etc)
rd
The 3 number indicates Weekday: 0,1, 2, ..,6(for Sun, Mon, Tue, .., Sat)
Therefore, this example is the DST which starts from the second Sunday of March to the
1st Sunday of November.
Allow DHCP server to
set Time Zone
Default No. Let the DHCP server handle the Time Zone
Language
Languages supported with voice prompt and web interface, except Spanish that it is only
in IVR.
Reset Type
Gives the user the option to set to default all VoIP related configuration (mainly everything
located on FXS/Profile page), all ISP (Internet Service Provider) configuration which may
affect the IP address, or both at the same time.
Note: After you choose the reset type, you will have to click the reset button for it to take
effect.
In addition to the Basic Settings configuration page, end users also have access to the Device Status
page.
Table 9: Status Page
MAC Address
The device ID, in HEX format. This is very important ID for ISP troubleshooting. The Mac
address will appear in this place. The MAC address will be used for provisioning and can
be found on the label coming with original box and on the label located on the bottom
panel of the device.
IP Address
This field shows the IP address of the HT70X.
Product Model
This field contains the product model info.
Hardware Version
This field shows the hardware revision of the unit and the part number.
Software Version
Program: This is the main software release. This number is always used for firmware
upgrade. Current release is 1.0.0.18 Boot and Loader are seldom changed.
Bootloader: current version is 1.0.0.6.
Core: current version 1.0.0.18
Base: current version is 1.0.0.18
System Up Time
Shows system up time since the last reboot.
PPPoE Link Up
Indicates whether the PPPoE connection is up if the HT70X is connected to DSL modem.
NAT
This filed indicates the type of NAT connection used by the HT70X.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 19 of 35
Last Updated: 03/2012
Port Status
Displays relevant information regarding the FXS port.
•
•
•
•
Port
Hook
Registration
DND
Forward
FXS
On Hook
Registered
Yes
613
Busy
Forward
Delayed
Forward
FXS port is registered with SIP Server.
FXS Port user has set Do Not Disturb.
FXS Port user has set his calls to be unconditionally forwarded to ext 613.
FXS Port user has not set Busy or Delay call Forward.
Advanced User Configuration
Log in to the advanced user configuration page the same way as for the basic configuration page.
password is case sensitive and the factory default password for Advanced User is “admin”.
The
Advanced User configuration includes the end user configuration and the advanced configurations
including: a) SIP configuration, b) Codec selection, c) NAT Traversal Setting and d) other miscellaneous
configuration. HT701 and HT702 FXS SIP account(s) have its own configuration page. HT704 has two (2)
profiles for the four (4) FXS ports.
Table 10: Advanced Settings
Admin Password
This contains the password to access the Advanced Web Configuration page. This field is
case sensitive. Only the administrator can configure the “Advanced Settings” page.
Password field is purposely left blank for security reasons after clicking update and saved.
The maximum password length is 25 characters.
Layer 3 QoS
This field defines the layer 3 QoS parameter which can be the value used for IP
Precedence or Diff-Serv or MPLS. Default value is 48.
Layer 2 QoS
Value used for layer 2 VLAN tag. Default setting is blank.
STUN Server
IP address or Domain name of the STUN server.
Keep-alive interval
This parameter specifies how often the HT70X sends a blank UDP packet to the SIP
server in order to keep the “hole” on the NAT open. Default is 20 seconds. Minimum
value is 20 seconds.
Use STUN to detect
network connectivity
Use STUN keep-alive to detect WAN side network problems. If keep-alive request does
not yield any response for configured number of times, the device will restart the TCP/IP
stack. If the STUN server does not respond when the device boots up, the feature is
disabled. Default setting is No.
Firmware Upgrade
and Provisioning
Enables HT70X to download firmware or configuration file through either the TFTP, HTTP
or HTTPS server.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 20 of 35
Last Updated: 03/2012
Via TFTP Server
This is the IP address of the configured TFTP server. If selected and it is non-zero or not
blank, the HT70X retrieves the new configuration file or new code image from the
specified TFTP server at boot time. After 5 attempts, the system will timeout and will start
the boot process using the existing code image in the Flash memory. If a TFTP server is
configured and a new code image is retrieved, the new downloaded image is saved into
the Flash memory.
Note: Please do NOT interrupt the TFTP upgrade process (especially the power supply)
as this will damage the device. Depending on the local network, this process can take up
to 15 or 20 minutes.
Via HTTP / HTTPS
Server
The URL for the HTTP/HTTPS server used for firmware upgrade and configuration via
HTTP.
For example, http://provisioning.mycompany.com:6688/Grandstream/1.0.0.67“:6688” is
the specific TCP port where the HTTP or HTTPS server is listening; it can be omitted if
using default port 80.
Note: If Auto Upgrade is set to No, HT70X will only do HTTP/HTTPS download once at
boot up.
Firmware Server Path
IP address or domain name of firmware server.
Config Server Path
IP address or domain name of configuration server.
XML Config File
Password
The password used for encrypting the XML configuration file using OpenSSL.
This is required for the phone to decrypt the encrypted XML configuration file.
HTTP/HTTPS User
Name
The user name needed to authenticate with the HTTP/HTTPS server.
HTTP/HTTPS
Password
The password needed to authenticate with the HTTP/HTTPS server.
Firmware File Prefix
Default is blank. If configured, HT701 will request firmware file with the prefix.
setting is useful for ITSPs. End user should keep it blank.
Firmware File Postfix
Default is blank. End user should keep it blank.
Config File Prefix
Default is blank. End user should keep it blank.
Config File Postfix
Default is blank. End user should keep it blank.
This
Allow DHCP Option 66 If set to “Yes”, configuration and upgrade server information can be obtained using DHCP
to override server
option 66 from DHCP server located in customer‟s environment. Default setting is Yes.
Automatic Upgrade
Choose “Yes” to enable automatic upgrade and provisioning. If select “Check every
minutes” input the amount of minutes you want it to check for update. If select “Yes, daily
at hour” make sure to input the hour of the day you want it to check for update, e.g. for 11
pm type 23. If select “Yes, weekly on day” make sure you input the day of the week (in
format 0-6, 0 is Sunday) you want it to check for update. When set to No, HT70X will only
do the following option you select; “Always check for New Firmware at Boot up” will check
for new firmware every time the device reboots. “Check New Firmware only when F/W
pre/suffix changes” will check for updates only when the pre/suffix has been changed.
Authenticate Conf File If set to Yes, config file is authenticated before acceptance.
configuration from an unauthorized change.
This protects the
Firmware Key
Used for firmware encryption. Should be 32 digit in hexadecimal representation. End
user should keep it blank.
SSL Certificate
The user specify SSL certificate used for SIP over TLS in X.509 format.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 21 of 35
Last Updated: 03/2012
SSL Private Key
The user specify SSL private key used for SIP over TLS in X.509 format.
SSL Private Key
Password
User specify password to protect the private key above.
ACS URL
User specify the Auto Configuration Server‟s URL (TR-069 protocol)
ACS Username
User specify the ACS Username
ACS Password
User specify the ACS password
Periodic Inform
Enable
Default is No. If set to YES, device will send inform packets to the ACS
Periodic Inform
Interval
Frequency that the inform packets will be sent out to the ACS
Connection Request
Username
Set a user name for the ACS to connect to this device
Connection Request
Password
Set a password for the ACS to connect to this device
System Ring Cadence
Configuration option is set ring cadence on all FXS ports for all incoming calls. (Syntax:
c=on1/off1-on2/off2-on3/off3(only 3 cadences maximum)) Default is set to c=2000/4000;
(US standards)
Call Progress Tones
Using these settings, users can configure tone frequencies and cadence according to
their preference. By default they are set to North American frequencies. Configure these
settings with known values to avoid uncomfortable high pitch sounds. ON is the period of
ringing (“On time” in „ms‟) while OFF is the period of silence. In order to set a continuous
tone, OFF should be zero. Otherwise it will ring ON ms and a pause of OFF ms and then
repeat the pattern.
Example configuration for N.A. Dialtone:
f1=350@-13,f2=440@-13,c=0/0;
Syntax: f1=freq@vol, f2=freq@vol, c=on1/off1-on2/off2-on3/off3; [...]
(Note: freq: 0 - 4000Hz; vol: -30 - 0dBm)
Lock Keypad Update
Default is No. If set to “Yes”, the configuration update via keypad is disabled.
Disable Voice Prompt
Default is No. Disables the voice prompt configuration.
Disable Direct IP Call
Default is No. Disables the Direct IP Call function.
Failover to FXO
Gateway
Default is Disable. If Enabled, the unit will start routing the calls to the FXO Gateway
configured via Direct IP Call When it loses registration from your SIP Server. HT704 Only
The use of this option presumes a configured GXW410x or another FXO gateway with an
active PSTN line connection.
FXO Gateway
IP or Domain Name of the FXO Gateway that will be used as Failover. HT704 Only
NTP server
URI or IP address of the NTP (Network Time Protocol) server. This parameter
synchronizes the date and time.
Allow DHCP option 42 Default NO. Enables the DHCP server to handle the NTP Server via Option 42
to override NTP serve
Syslog Server
The IP address or URL of System log server. This feature is especially useful for the ITSP
(Internet Telephone Service Provider)
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 22 of 35
Last Updated: 03/2012
Syslog Level
Select the HT701 to report the log level. Default is NONE. The level is one of DEBUG,
INFO, WARNING or ERROR. Syslog messages are sent based on the following events:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
product model/version on boot up (INFO level)
NAT related info (INFO level)
sent or received SIP message (DEBUG level)
SIP message summary (INFO level)
inbound and outbound calls (INFO level)
registration status change (INFO level)
negotiated codec (INFO level)
Ethernet link up (INFO level)
SLIC chip exception (WARNING and ERROR levels)
memory exception (ERROR level)
The Syslog uses USER facility. In addition to standard Syslog payload, it contains the
following components:
GS_LOG: [device MAC address][error code] error message
Example: May 19 02:40:38 192.168.1.14 GS_LOG: [00:0b:82:00:a1:be][000] Ethernet link
is up
Send SIP Log
Default is No. If Enabled, the HT70X will send a replicate of the SIP packets on the
syslog.
Set the IP or FQDN of the Primary RADIUS Server. HT704 Only
Primary RADIUS
Server
Remote Authentication Dial In User Service (RADIUS). HT704 supports RADIUS for
authentication, authorization and billing purposes. Primary and secondary RADIUS server
configurations are available to provide redundancy to this feature. In case Primary Radius
server becomes unusable, RADIUS requests will be automatically sent to the secondary
server. When at least one RADUIS server was configured, the device will allow users to
make phone calls only after authorization from RADIUS server has been received. CDR
(Call Detail Record) is also sent to the RADIUS server for billing purposes. RAIDUS
server can send requests to terminate calls when run out of pre-paid credit.
Primary RADIUS Auth
Port
Default is 1812. Specifies the port to be used for the Primary RADIUS Authentication.
HT704 Only
Primari RADIUS Acct
Port
Default is 1813. Specifies the port to be used for the Primary RADIUS Account. HT704
Only
Primary RADIUS
Server Secret
Specifies the secret string to be used to authenticate the RADIUS connection to the
Primary Server. It should match RADIUS configuration. HT704 Only
Secondary RADIUS
Server
Set the IP or FQDN of the Secondary RADIUS Server. HT704 Only
In case Primary Radius server becomes unusable, secondary will take role of primary and
will manage credit recourses in the network
Secondary RADIUS
Auth Port
Default is 1812. Specifies the port to be used for the Secondary RADIUS Authentication.
HT704 Only
Secondary RADIUS
Acct Port
Default is 1813. Specifies the port to be used for the Secondary RADIUS Account. HT704
Only
Secondary RADIUS
Server Secret
Specifies the secret string to be used to authenticate the RADIUS connection to the
Secondary Server. It should match RADIUS configuration HT704 Only
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 23 of 35
Last Updated: 03/2012
RADIUS Timeout
Default is 2. HT704 Only
RADIUS Retry
Default is 3. HT704 Only
Download Device
Configuration
Allows user to download and save a text file containing all the P values of each setting as
configured at that point on the unit. (Note: For Security Reasons, all Passwords won‟t be
Downloaded)
Upload Firmware
Allows the user to upgrade the firmware with a single firmware file by browsing and
loading the file from your computer (local directory).
Table 11: Account Settings
Profile Active
When set to Yes the FXS port or Profile (for HT704) is activated.
Primary SIP Server
SIP Server‟s IP address or Domain name provided by VoIP service provider.
Failover SIP Server
Failover SIP Server‟s IP address or Domain name in case primary server does not
respond.
Prefer Primary SIP
Server
Default is No. If set to yes, it will register to Primary Server if registration with Failover
server expires
Outbound Proxy
IP address or Domain name of Outbound Proxy, or Media Gateway, or Session Border
Controller. Used by HT70X for firewall or NAT penetration in different network
environments. If symmetric NAT is detected, STUN will not work and ONLY outbound
proxy can correct the problem.
SIP transport
NAT Traversal (STUN)
User can select UDP or TCP or TLS. Default is UDP.
This parameter defines whether or not the HT70X NAT traversal mechanism is
activated. If activated (by choosing “Yes”) and a STUN server is also specified, then the
HT70X performs according to the STUN client specification. Using this mode, the
embedded STUN client will detect if and what type of firewall/NAT. If the detected NAT
is a Full Cone, Restricted Cone, or a Port-Restricted Cone, the HT70X will use its
mapped public IP address and port in all of its SIP and SDP messages.
If the NAT Traversal field is set to “Yes” with no specified STUN server, the HT70X will
periodically (every 20 seconds or so) send a blank UDP packet (with no payload data)
to the SIP server to keep the “hole” on the NAT open.
SIP User ID
User account information, provided by VoIP service provider (ITSP). Usually in the form
of digit similar to phone number or actually a phone number. HT701 and HT702 only
Authenticate ID
SIP service subscriber‟s Authenticate ID used for authentication. Can be identical to or
different from SIP User ID. HT701 and HT702 only
Authenticate Password
SIP service subscriber‟s account password. HT701 and HT702 only
Name
SIP service subscriber‟s name for Caller ID display. HT701 and HT702 only
DNS Mode
One from the 3 modes are available for “DNS Mode” configuration:
-A Record (for resolving IP Address of target according to domain name)
-SRV (DNS SRV resource records indicates how to find services for various protocols)
-NAPTR/SRV (Naming Authority Pointer according to RFC 2915)
One mode can be chosen for the client to look up server.
The default value is “A Record”
Tel URI
The default setting is “Disabled”. If the phone has an assigned PSTN
Number, this field should be set to “User=Phone” then a
“User=Phone” parameter will be attached to the “From header” in the SIP
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 24 of 35
Last Updated: 03/2012
request to indicate the E.164 number. If server supports TEL URI format, then this
option needs to be selected.
SIP Registration
Controls whether the HT701 needs to send REGISTER messages to the proxy server.
The default setting is Yes.
Unregister on Reboot
Default is No. If set to Yes, the SIP user‟s registration information will be cleared on
reboot.
Outgoing Call without
Registration
Default is No. If set to “Yes,” user can place outgoing calls even when not registered (if
allowed by Internet Telephone Service Provider) but is unable to receive incoming
calls.
Register Expiration
This parameter allows the user to specify the time frequency (in minutes) the HT70X
refreshes its registration with the specified registrar. The default interval is 60 minutes
(or 1 hour). The maximum interval is 65535 minutes (about 45 days).
Registration Retry Wait
Time
Retry registration if the process failed. Default is 20 seconds.
Local SIP port
Defines the local SIP port the HT70X will listen and transmit. The default value for FXS
port is 5060.
Local RTP port
Defines the local RTP-RTCP port pair the HT70X will listen and transmit. It is the base
RTP port for channel 0. When configured,
channel 0 uses this port _value for RTP and the port_value+1 for its RTCP
The default value for FXS port is 5004.
Use Random Port
Default is No. This parameter forces the random generation of both the local SIP and
RTP ports when set to Yes. This is usually necessary when multiple HT70X are behind
the same NAT.
Refer to Use Target
Contact
Default is No. If set to YES, then for Attended Transfer, the “Refer-To” header uses the
transferred target‟s Contact header information.
Transfer on Conference
Hang up
Default is No. In which case if the conference originator hangs up the conference will
be terminated. When option YES is chosen, originator will transfer other parties to
each other so that B and C can choose to either continue the conversation or
hang up.
Enable Ring-Transfer
Disable Bellcore Style
3-Way Conference
Remove OBP from
Route Header
Support SIP Instance ID
Validate incoming SIP
message
Check SIP User ID for
incoming INVITE
Allow Incoming SIP
Messages from SIP
Proxy Only
SIP T1 Timeout
SIP T2 Interval
DTMF Payload Type
Grandstream Networks, Inc.
Default is No, this will create a Semi-Attendant Transfer. When set to Yes, device can
transfer the call upon receiving ring back tone or SIP message 180.
Default is No. you can make a Conference by pressing „Flash‟ key. If set to Yes, you
need to dial *23 + second callee number.
Default is No. When option YES is chosen, the Out Bound Proxy will be removed from
Route header.
Default is Yes. If set to Yes, the contact header in REGISTER request will contain SIP
Instance ID as defined in IETF SIP Outbound draft.
Default is No. If set to yes all incoming SIP messages will be strictly validated
according to RFC rules. If message will not pass validation process, call will be
rejected.
Default is No. Check the incoming SIP User ID in Request URI. If they don‟t match, the
call will be rejected. If this option is enabled, the device will not be able to make direct
IP calls.
Default is No. Check the incoming SIP messages. If they don‟t come from the SIP
proxy, they will be rejected. If this option is enabled, the device will not be able to make
direct IP calls.
T1 is an estimate of the round-trip time between the client and server transactions.
If the network latency is high, select larger value for more reliable usage. Default is 0.5
Sec.
Maximum retransmission interval for non-INVITE requests and INVITE responses.
Default is 4 Sec.
Sets the payload type for DTMF using RFC2833. Default is 101.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 25 of 35
Last Updated: 03/2012
Preferred DTMF method
Disable DTMF
Negotiation
The HT70X supports up to 3 different DTMF methods including in-audio, via RTP
(RFC2833) and via Sip Info using SIP INFO messages. The user can configure DTMF
method in a priority list.
Default is No. If set to yes, use above DTMF order without negotiation
Send Flash Event
Default is No. If set to yes, flash will be sent as DTMF event.
Enable Call Features
Default is Yes. (If Yes, call features using star codes will be supported locally)
Offhook Auto-Dial
This parameter allows users to configure a User ID or extension number that is
automatically dialed when off-hook. Only the user part of a SIP address needs to be
entered here. The HT70X will automatically append the “@” and the host portion of the
corresponding SIP address. HT701 and HT702 only
Proxy-Require
SIP Extension to notify SIP server that the unit is behind the NAT/Firewall.
Use NAT IP
Distinctive Ring Tone
NAT IP address used in SIP/SDP message. Default is blank.
Custom Ring Tone 1 to 3 with associate Caller ID: when selected, if Caller ID is
configured, then the device will ONLY uses this ring tone when the incoming call is
from the Caller ID. System Ring Tone is used for all other calls. When selected but no
Caller ID is configured, the selected ring tone will be used for all incoming calls using
the FXS port or Profile. Distinctive ring tones can be configured not only for matching a
whole number, but also for matching prefixes. In this case symbol * (star) will be used.
For example:
if configured as *617, Ring Tone 1 will be used in case of call arrived from the area
code 617. Any other incoming call will ring using cadence defined in parameter System
Ring Cadence located under Advanced Settings Configuration page.
Note: If server supports Alert-Info header and standard ring tone set (Bellcore) or
distinctive ring tone 1-10 is specified, then the ring tone in the Alert-Info header from
server will be used. Bellcore rings and tones are independent from custom ring tones.
The custom ring tones can also be specified by alert-info header, for example
Alert-Info: <http://127.0.0.1>;info=ring5
Disable Call Waiting
Default is No. If set to YES Call Waiting indication information will not be provided to
analog phone connected to this FXS port.
Disable Call-Waiting
Caller ID
Disable Call Waiting
Tone
Disable Receiver
Offhook Tone
Disable Reminder Ring
for On-Hold Call
Disable Visual MWI
Default is No. If set to YES Call Waiting caller ID will not be provided to analog phone
connected to this FXS port.
Default is No. This is to disable the stutter Call Waiting Tone when a Call Waiting
information arrives. The CWCID information will still be displayed.
Default is No. If set to yes, it will disable the warning to alert that the phone has been
left off-hook for an extended period of time.
Default is No. Do not play the reminder ring when this is set to Yes.
Ring Timeout
Hunting Group Ring
Timeout
Hunting Group Type
Delayed Call Forward
Wait Time
Grandstream Networks, Inc.
Default is No. If set to “Yes”, the MWI information will not be transferred to the analog
phone connected to the FXS port.
Default value is 60 Sec. Incoming call will stop ringing when not picked up given a
specific period of time.
Default value is 20 Sec. If call is not answered within this designated time period, the
callwill be forwarded to the next member of a Hunt Group. HT704 only
Linear and Circular. Default is Circular. Linear style will sort the call to the lowestnumbered available line, this is also called “serial hunting”. Circular style will distribute
the calls "round-robin". If a call is assigned to line 1, the next call goes to 2 and the next
to 3. The succession throughout each of the lines continues even if one of the previous
lines becomes available. When the end of the hunt group is reached, the hunting starts
over at the firstline. Lines are skipped if they are still busy on a previous call. HT704
only
Default value is 20 seconds. In case this feature activated using * codes (*92 code),
the call will be forwarded after this preconfigured amount of time.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 26 of 35
Last Updated: 03/2012
No Key Entry Timeout
Early Dial
Default is 4 seconds. Dialing process is completed and outgoing call is initiated if no
key entry occurs during this preconfigured interval.
Default is No. Use only if proxy supports 484 response. This parameter controls
whether the phone will send an early INVITE each time a key is pressed when a user
dials a number. If set to “Yes”, an INVITE is sent using the dial-number collected thus
far; Otherwise, no INVITE is sent until the “(Re-)Dial” button is pressed or after about 5
seconds have elapsed if the user forgets to press the “Re-Dial” button.
The “Yes” option should be used ONLY if there is a SIP proxy configured and the proxy
server supports 484 Incomplete Address response. Otherwise, the call will likely be
rejected by the proxy (with a 404 Not Found error).
Dial Plan Prefix
Use # as Dial Key
Dial Plan
This feature does NOT work with and should NOT be enabled for direct IP-to-IP calling.
Sets the prefix added to each dialed number.
Default is Yes. It allows users to configure the “#” key as the “Send” (or “Dial”) key. If
set to “Yes”, “#” will send the number. In this case, this key is essentially equivalent to
the “Dial” key. If set to “No”, this “#” key can be included as part of number.
Dial Plan Rules:
1. Accept Digits: 1,2,3,4,5,6,7,8,9,0 , *, #, A,a,B,b,C,c,D,d
2. Grammar: x - any digit from 0-9;
 xx+ - at least 2 digits number;
 xx. – at least 2 digit number.
 ^ - exclude;
 [3-5] - any digit of 3, 4, or 5;
 [147] - any digit 1, 4, or 7;
 <2=011> - replace digit 2 with 011 when dialing
 < =1> - add a leading 1 to all numbers dialed, vice versa will remove
a 1 from the number dialed
 | - or
• Example 1: {[369]11 | 1617xxxxxxx} – Allow 311, 611, 911, and any 11 digit
numbers with leading digits 1617
Example 2: {^1900x+ | <=1617>xxxxxxx} – Block any number of leading digits
1900 and add prefix 1617 for any dialed 7 digit numbers
• Example 3: {1xxx[2-9]xxxxxx | <2=011>x+} –Allow any combinations of numbers
with 11 digits which has a leading digit 1, but 5th digit cannot be 0 or 1. Or any length
of numbers with a minimum of 2 digits beginning with 2, with the leading digit
replaced with 011.
3. Default: Outgoing - {x+}
Example of a simple dial plan used in a Home/Office in the US:
{ ^1900x. | <=1617>[2-9]xxxxxx | 1[2-9]xx[2-9]xxxxxx | 011[2-9]x. | [3469]11 }
Explanation of example rule (reading from left to right):
• ^1900x. - prevents dialing any number started with 1900
• <=1617>[2-9]xxxxxx - allows dialing to local area code (617) numbers by dialing
7 numbers and 1617 area code will be added automatically
• 1[2-9]xx[2-9]xxxxxx |- allows dialing to any US/Canada Number with 11 digits
length
• 011[2-9]x. - allows international calls starting with 011
• [3469]11 - allow dialing special and emergency numbers 311, 411, 611 and 911
Note: In some cases user wishes to dial strings such as *123 to activate voice mail or
other application provided by service provider. In this case * should be predefined
inside dial plan feature and the Dial Plan should be: { *x+ }.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 27 of 35
Last Updated: 03/2012
Subscribe for MWI
Default is No. When set to “Yes” a SUBSCRIBE for Message Waiting Indication will be
sent periodically.
Send Anonymous
Default is No. If this parameter is set to “Yes”, the “From” header along with Privacy
and P_ Asserted_Identity headers in outgoing INVITE message will be set to
anonymous, blocking Caller ID.
Anonymous Call
Rejection
Default is No. If set to Yes, incoming calls with anonymous Caller ID will be rejected
with 486 Busy message.
Special Feature
Default is Standard. Choose the selection to meet some special requirements from
Softswitch vendors.
Session Expiration
Grandstream implemented SIP Session Timer. The session timer extension enables
SIP sessions to be periodically “refreshed” via a SIP request (UPDATE, or re-INVITE.
Once the session interval expires, if there is no refresh via a UPDATE or re-INVITE
message, the session will be terminated. Session Expiration is the time (in seconds) at
which the session is considered timed out, if no successful session refresh transaction
occurs beforehand. The default value is 180 seconds.
The minimum session expiration (in seconds). The default value is 90 seconds.
Min-SE
G723 Rate
Default is No. If selecting “Yes” the phone will use session timer when it makes
outbound calls if remote party supports session timer.
Default is No. If selecting “Yes” the phone will use session timer when it receives
inbound calls with session timer request.
Default is No. If selecting “Yes” the phone will use session timer even if the remote
party does not support this feature. Selecting “No” will allow the phone to enable
session timer only when the remote party support this feature. To turn off Session
Timer, select “No” for Caller Request Timer, Callee Request Timer, and Force Timer.
Default is Omit. As a Caller, select UAC to use the phone as the refresher, or UAS to
use the Callee or proxy server as the refresher.
Default is UAC. As a Callee, select UAC to use caller or proxy server as the refresher,
or UAS to use the phone as the refresher.
Session Timer can be refreshed using INVITE method or UPDATE method. Select
“Yes” to use INVITE method to refresh the session timer. Default is No,
Default is No, If set to “Yes”, device will send an INVITE with audio vocoders upon
completion of Fax to continue session in audio only.
For fax machines that do not send a Disconnect when fax is done. This option
Enables/Disables the detection of silence in order to know the fax has finished. The
silence period is non-configurable and fixed to 7 seconds. Default is No,
Default is No, If set to Yes, Enables the use of PRACK (Provisional Acknowledgment)
method.
Default is No. If set to “Yes”, device will include only the first match vocoder in its
200OK response, otherwise it will include all match vocoders in same order received in
INVITE.
The HT70X supports up to 5 different Vocoder types including G.711 A-/U-law, G.72632, G.723.1, G.729A/B/E, iLBC. The user can configure Vocoders in a preference list
that will be included with the same preference order in SDP message. The first
Vocoder is entered by choosing the appropriate option in “Choice 1”. The last Vocoder
is entered by choosing the appropriate option in “Choice 8”.
Vocoder types can also be changed per call basis by using a star code. Please see the
“Call features” section.
Default is 6.3kbps. Defines the encoding rate for G.723.1 vocoder.
iLBC Frame Size
Default is 20ms. Sets the iLBC frame size in 20ms or 30ms.
iLBC Payload type
Defines payload type for iLBC. Default value is 97. The valid range is between 96 and
127.
Default is No. VAD allows detecting the absence of audio and conserve bandwidth by
preventing the transmission of "silent packets" over the network.
Caller Request Timer
Callee Request Timer
Force Timer
UAC Specify Refresher
UAS Specify Refresher
Force INVITE
Send Re-INVITE After
Fax
Enable Silence
Detection for Fax
Disconnect
Enable 100rel
Use First Matching
Vocoder in 200OK SDP
Preferred Vocoder
VAD
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 28 of 35
Last Updated: 03/2012
Symmetric RTP
Fax Mode
Default is No. When set to Yes the device will change the destination to send RTP
packets to the source IP address and port of the inbound RTP packet last received by
the device.
T.38 (Auto Detect) FoIP by default, or Pass-Through (must use codec PCMU/PCMA)
Re-Invite after Fax Tone
Detection Mode
Jitter Buffer Type
Default is Enabled. It makes the unit send out the re-INVITE for T.38 or Fax Pass
Through if a fax tone is detected.
Select either Fixed or Adaptive based on network conditions. Default is Adaptive.
Jitter Buffer Length
SLIC Setting
Select Low, Medium or High based on network conditions. Default is Medium.

High (initial 200ms, min 40ms, max 600ms) Note: not all vocoders can meet
the high requirement

Medium (initial 100ms, min 20ms, max 200ms)

Low (initial 50ms, min 10ms, max 100ms)
This option defines different implementation of support SRTP (squired RTP)
transmission mode. Select between Disabled, Enabled but not Forced, and Enabled
and Forced. Default is Disabled.
Dependent on standard phone type (and location)
Caller ID Scheme
Bellcore/Telcordia, ETSI-FSK, ETSI-DTMF, SIN 227 – BT, & NTT Japan
Polarity Reversal
Default is No. If set to “Yes”, polarity will be reversed upon call establishment and
termination.
Default is No. Set it to Yes if the traditional PBX you are using with HT70X uses this
method for signaling call termination. Method initiates short voltage drop on the line
when remote (VoIP) side disconnects an active call.
SRTP Mode
Loop Current
Disconnect
Loop Current
Disconnect Duration
Hook Flash Timing
On Hook Timing
Gain
Default value is 200. Here can be configured duration of such voltage drop described in
topic above. HT70X supports a Duration Range from 100 to 10000 ms.
Time period when the cradle is pressed (Hook Flash) to simulate FLASH. To prevent
unwanted activation of the Flash/Hold and automatic phone ring-back, adjust this time
value. Default values are 300 minimum and 1100 maximum. HT70X supports a
range from 40 to 2000 ms.
On-hook timing is the minimum time for an on-hook event to be validated. Default
value is 400 . HT70X supports a range from 40 to 2000 ms.
Voice path volume adjustment.
•
Rx is a gain level for signals transmitted by FXS
•
Tx is a gain level for signals received by FXS.
Default = 0dB for both parameters. Loudest volume: +6dB Lowest volume: -6dB.
User can adjust volume of call on either end using the Rx Gain Level parameter and
the Tx Gain Level parameter located on the FXS Port Configuration page.
If call volume is too low when using the FXS port (ie. the ATA is at user site), adjust
volume using the Rx Gain Level parameter under the FXS Port Configuration page.
Disable Line Echo
Canceller (LEC)
Ring Tones
Grandstream Networks, Inc.
If voice volume is too low at the other end, user may increase the far end volume using
the Tx Gain Level parameter under the FXS Port Configuration page.
Default is No. If set to “Yes” LEC will be disabled per call base. Recommended for
FAX/Data calls.
This function lets you configure ring tone cadence preferences. User has 10 choices.
The configuration, completed in Distinctive Ring Tones block in the same page, applies
to ring tones cadences configured here.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 29 of 35
Last Updated: 03/2012
Table 12: HT704 FXS Ports Settings
SIP Use ID
User account information, provided by VoIP service provider (ITSP). Usually in the form
of digit similar to phone number or actually a phone number.
Authenticate ID
SIP service subscriber‟s Authenticate ID used for authentication. Can be identical to or
different from SIP User ID.
Password
SIP service subscriber‟s account password for HT704 to register to (SIP) servers of
ITSP.
Name
Any name to identify this specific user.
Profile ID
Select the corresponding Profile ID between Profile 1 and Profile 2.
Hunting Group
This feature enables the HT704 to register all existing FXS ports with the same phone
number. Each incoming call will be routed to first available port in Linear or Circular
mode. User may configure all ports as members of the same Hunting Group or it may
configure different port combinations for more than one Hunting Group. For example:
Ports 1, 3 and 5 are members of the same Hunting Group, the rest of the ports may
have separate numbers and may be reached independently. Any port, member of a
Hunting Group that is not registered with a SIP account, will be able to place outbound
calls using the SIP credentials of the primary Hunting Group port.
For example: Port 1, 2, and 3 are members of the same Hunting Group. Port 1 is
registered with a SIP account. Ports 2, and 3 are not registered. Ports 2 and 3 will be
able to place outbound calls using the SIP account of port 1. Select appropriate value
for Hunting Group feature. The original SIP account should be set to Active while the
group members should be set to the port number of the Active Port.
Example configuration of a Hunting group:
FXS Port #1: SIP UserID and Authenticate ID entered, Hunting group set to "Active"
FXS Port #2: SIP UserID and Authenticate ID left blank, Hunting Group set to "1"
FXS Port #3: SIP UserID and Authenticate ID left blank, Hunting Group set to "1"
FXS Port #4: SIP UserID and Authenticate ID entered, Hunting group set to "None"
Hunting Group 1 contains ports 1, 2, 3. FXS port 4 is registered but it is not added to
the Hunting Group 1.
This feature allows you to automatically dial the number specified in this field as soon
as the port is offhooked, i.e. when the receiver on the phone connected to Port# is
picked up.
Offhook Auto-dial
Map to FXP Port #
This is used only when peering with a Grandstream GXW410x. Default is 1, Supported
values are 1-8, meaning line 1 to line 8 of the GXW410x device where the port will be
mapped to.
Map to FXO Gateway IP
This is used when peering with an FXO gateway of any brand. You have to specifically
mention the IP address where the call will be sent to.
and Port
Sip port that will be annexed to the IP address above.
Saving the Configuration Changes
Click the “Update” button in the Configuration page to save the changes to the HT70X configuration. The
following screen confirms that the changes are saved. Reboot or power cycle the HT70X to make the
changes take effect.
Rebooting the HT70X from Remote
Press the “Reboot” button at the bottom of the configuration menu to reboot the ATA remotely. The web
browser will then display a message window to confirm that reboot is underway. Wait 30 seconds to log in
again.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 30 of 35
Last Updated: 03/2012
Configuration through a Central Server
Grandstream HT70X can be automatically configured from a central provisioning system.
When HT70X boots up, it will send TFTP or HTTP/HTTPS request to download configuration file,
“cfg000b82xxxxxx” or “cfg00082xxxxxx.xml”, where “000b82xxxxxx” is the MAC address of the HT70X. It
will first request “cfg000b82xxxxxx” then “cfg000b82xxxxxx.xml”
The configuration file can be downloaded via TFTP or HTTP/HTTPS from the central server. A service
provider or an enterprise with large deployment of HT70X can easily manage the configuration and service
provisioning of individual devices remotely from a central server.
Grandstream has a provisioning system called GAPS (Grandstream Automated Provisioning System) that
is used to support automated configuration of Grandstream devices. GAPS uses enhanced (NAT friendly)
TFTP or HTTP (thus no NAT issues) and other communication protocols to communicate with each
individual Grandstream device for firmware upgrade, remote reboot, etc.
Grandstream provides GAPS service to VoIP service providers. Use GAPS for either simple redirection or
with certain special provisioning settings.
At boot-up, Grandstream devices by default point to
Grandstream provisioning server GAPS, based on the unique MAC address of each device, GAPS
provision the devices with redirection settings so that they will be redirected to customer‟s TFTP or
HTTP/HTTPS server for further provisioning. Grandstream also provide GAPSLITE software package
which contains our NAT friendly TFTP server and a configuration tool to facilitate the task of generating
device configuration files.
The configuration tool is now free to end users. The tool and configuration template are available for
download from http://www.grandstream.com/support/tools .
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 31 of 35
Last Updated: 03/2012
SOFTWARE UPGRADE
Software upgrade can be done via either TFTP or HTTP. The corresponding configuration settings are in
the ADVANCED SETTINGS configuration page.
Firmware Upgrade through TFTP/HTTP/HTTPS
To upgrade via TFTP or HTTP/HTTPS, the “Firmware Upgrade and Provisioning upgrade via” field needs
to be set to TFTP HTTP or HTTPS, respectively. “Firmware Server Path” needs to be set to a valid URL of
a TFTP or HTTP server, server name can be in either FQDN or IP address format. Here are examples of
some valid URL.
e.g. firmware.mycompany.com:6688/Grandstream/1.0.0.18
e.g. 72.172.83.110
NOTES:
 Firmware upgrade server in IP address format can be configured via IVR. Please refer to the
CONFIGURATION GUIDE section for instructions. If the server is in FQDN format, it must be set
via the web configuration interface.

Grandstream recommends end-user use the Grandstream HTTP server. Its address can be found
at http://www.grandstream.com/support/firmware . Currently the HTTP firmware server IP address
is 72.172.83.110. For large companies, we recommend to maintain their own TFTP/ HTTP/HTTPS
server for upgrade and provisioning procedures.

Once a “Firmware Server Path” is set, user needs to update the settings and reboot the device. If
the configured firmware server is found and a new code image is available, the HT70X will attempt
to retrieve the new image files by downloading them into the HT70X‟s SRAM. During this stage,
the HT70X‟s LEDs will blink until the checking/downloading process is completed. Upon verification
of checksum, the new code image will then be saved into the Flash. If TFTP/HTTP/HTTPS fails for
any reason (e.g. TFTP/HTTP/HTTPS server is not responding, there are no code image files
available for upgrade, or checksum test fails, etc), the HT70X will stop the TFTP/HTTP/HTTPS
process and simply boot using the existing code image in the flash.

Firmware upgrade may take as long as 15 to 30 minutes over Internet, or just 5 minutes if it is
performed on a LAN. It is recommended to conduct firmware upgrade in a controlled LAN
environment if possible. For users who do not have a local firmware upgrade server, Grandstream
provides a NAT-friendly TFTP server on the public Internet for firmware upgrade.

Grandstream‟s latest firmware is available at http://www.grandstream.com/support/firmware .
Oversea users are strongly recommended to download the binary files and upgrade firmware
locally in a controlled LAN environment.
Note: Alternatively, the user can upload the firmware single file from his/her computer using a local
directory. For more instructions see below. Also the user can download a free TFTP or HTTP server and
conduct local firmware upgrade. A free windows version TFTP server is available for download from
http://support.solarwinds.net/updates/New-customerFree.cfm.
Our latest official release can be
downloaded from http://www.grandstream.com/support/firmware .
Instructions for Upload from Local Directory:
1- Download the firmware file from Grandstream web site
2- Unzip it and copy the file in to a folder in your PC
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 32 of 35
Last Updated: 03/2012
3- From the HT70X web interface (Advanced Settings page) you can browse your hard drive and
select the folder you previously saved the file (ht70xfw.bin)
4- Click “Upload Firmware” and wait few minutes until the new program is loaded.
Note: Always check the status page to see that the program version has changed.
Instructions for local firmware upgrade using TFTP server:
1. Unzip the file and put all of them under the root directory of the TFTP server.
2. Put the PC running the TFTP server and the HT701 device in the same LAN segment.
3. Please go to File -> Configure -> Security to change the TFTP server's default setting from
"Receive Only" to "Transmit Only" for the firmware upgrade.
4. Start the TFTP server, in the phone‟s web configuration page
5. Configure the Firmware Server Path with the IP address of the PC
6. Update the change and reboot the unit
End users can also choose to download the free HTTP server from http://httpd.apache.org/ or use
Microsoft IIS web server.
Configuration File Download
Grandstream SIP Device can be configured via Web Interface as well as via Configuration File through
TFTP or HTTP/HTTPS. “Config Server Path” is the TFTP or HTTP/HTTPS server path for configuration
file. It needs to be set to a valid URL, either in FQDN or IP address format. The “Config Server Path” can
be same or different from the “Firmware Server Path”.
A configuration parameter is associated with each particular field in the web configuration page. A
parameter consists of a Capital letter P and 1 to 3 (Could be extended to 4 in the future) digit numeric
numbers. i.e., P2 is associated with “Admin Password” in the ADVANCED SETTINGS page. For a
detailed parameter list, please refer to the corresponding firmware release configuration template.
When Grandstream Device boots up or reboots, it will issue request for configuration file named
“cfgxxxxxxxxxxxx”, where “xxxxxxxxxxxx” is the MAC address of the device, i.e., “cfg000b820102ab”. The
configuration file name should be in lower cases.
Firmware and Configuration File Prefix and Postfix
Firmware Prefix and Postfix allows device to download the firmware name with the matching Prefix and
Postfix. This makes it the possible to store ALL of the firmware with different version in one single directory.
Similarly, Config File Prefix and Postfix allows device to download the configuration file with the matching
Prefix and Postfix. Thus multiple configuration files for the same device can be stored in one directory.
In addition, when the field “Check New Firmware only when F/W pre/suffix changes” is set to “Yes”, the
device will only issue firmware upgrade request if there are changes in the firmware Prefix or Postfix.
Managing Firmware and Configuration File Download
When “Automatic Upgrade” is set “Yes, every” the auto check will be done in the minute specified in this
field. If set to “daily at hour (0-23)”, Service Provider can use P193 (Auto Check Interval) to have the
devices do a daily check at the hour set in this field with either Firmware Server or Config Server. If set to
“weekly on day (0-6)” the auto check will be done in the day specified in this field. This allows the device
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 33 of 35
Last Updated: 03/2012
periodically check if there are any new changes need to be taken on a scheduled time. By defining different
intervals in P193 for different devices, Server Provider can spread the Firmware or Configuration File
download in minutes to reduce the Firmware or Provisioning Server load at any given time.
Automatic Upgrade:
No
Yes, every
Yes, daily at hour
Grandstream Networks, Inc.
1
10080
(0-23).
minutes(60-5256000).
Yes, weekly on day
HT-70X User Manual
Firmware Version 1.0.0.18
1
(0-6).
Page 34 of 35
Last Updated: 03/2012
RESTORE FACTORY DEFAULT SETTING
WARNING! Restoring the Factory Default Setting will DELETE all configuration information of the phone.
Please BACKUP or PRINT out all the settings before you approach to following steps. Grandstream will not
take any responsibility if you lose all the parameters of setting and cannot connect to your VoIP service
provider.
FACTORY RESET
There are three (3) methods for resetting your unit:
Reset Button
Reset default factory settings following these four (4) steps:
1. Unplug the Ethernet cable.
2. Locate a needle-sized hole on the back panel of the gateway unit next to the power
connection.
3. Insert a pin in this hole, and press for about 7 seconds.
4. Take out the pin. All unit settings are restored to factory settings.
IVR Command
Reset default factory settings using the IVR Prompt (Table 5):
1. Dial “***” for voice prompt.
2. Enter “99” and wait for “reset” voice prompt.
3. Enter the encoded MAC address (Look below on how to encode MAC address).
4. Wait 15 seconds and device will automatically reboot and restore factory settings.
Encode the MAC Address
1. Locate the MAC address of the device. It is the 12 digit HEX number on the bottom of the unit.
2. Key in the MAC address. Use the following mapping:
0-9: 0-9
A:
22 (press the “2” key twice, “A” will show on the LCD)
B:
222
C:
2222
D:
33 (press the “3” key twice, “D” will show on the LCD)
E:
333
F:
3333
For example: if the MAC address is 000b8200e395, it should be keyed in as “0002228200333395”.
Reset from web interface (Reset Type)
1. From the Advanced Settings Page user can select three types:

Full Reset: This will make a full reset

ISP Data: This will reset only the basic settings, like IP mode, PPPoE and Web port

VOIP Data: This will reset only the data related with a service provider like SIP server, sip
user ID, provisioning and others.
NOTE:
1. Factory Reset will be disabled if the “Lock keypad update” is set to “Yes”.
2. If the HT70X was previously locked by your local service provider, pressing the RESET button will only
restart the unit. The device will not return to factory default settings.
Grandstream Networks, Inc.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 35 of 35
Last Updated: 03/2012