User´s Guide: BNI TCP-952-000-E029 EN

Balluff Network Interface
BNI TCP-952-000-E029
Industrial Ethernet Switch
This quick start guide describes how to install and use the Industrial Ethernet Switch.
This is the switch of choice for harsh environments constrained by space.
The Terminal Block and Power Inputs
Physical Description
Power Input Assignment
The Port Status LEDs
Power 1
Power 2
+
12~48VDC
-
Power Ground
+
12~48VDC
-
Power Ground
Terminal Block
Earth Ground
Relay Output Rating
1A @ 250VAC
DC Terminal Block Power Input: The DC Terminal Block power input can be used to
power up this Switch.
DIP Switch Settings
LED
Power 1, 2 (Green)
Fault (Red)
State
Indication
Steady
Power on.
Off
Power off.
Steady
Relay starts alarm.
Off
Relay non-alarm.
Steady
A valid network connection established.
Blinking
Transmitting or receiving data.
ACT stands for Activity.
Off
No link.
Ports
Link/ACT (Green)
www.balluff.com
DIP No.
On
Off
1
Port 1 Alarm Enable.
Port 1 Alarm Disable.
2
Port 2 Alarm Enable.
Port 2 Alarm Disable.
3
Port 3 Alarm Enable.
Port 3 Alarm Disable.
4
Port 4 Alarm Enable.
Port 4 Alarm Disable.
5
Port 5 Alarm Enable.
Port 5 Alarm Disable.
6
Port 6 Alarm Enable.
Port 6 Alarm Disable.
7
Port 7 Alarm Enable.
Port 7 Alarm Disable.
8
Port 8 Alarm Enable.
Port 8 Alarm Disable.
9
Broadcast Storm Protection Enable.
Broadcast Storm Protection Disable.
10
Reserved
1
Balluff Network Interface
The 10/100Base-TX and 100Base-FX/BX Connectors
The 10/100Base-TX Connections
The following lists the pinouts of 10/100Base-TX ports.
Pin
Regular Ports
Uplink port
1
Output Transmit Data +
Input Receive Data +
2
Output Transmit Data -
Input Receive Data -
3
Input Receive Data +
Output Transmit Data +
4
NC
NC
5
NC
NC
6
Input Receive Data -
Output Transmit Data -
7
NC
NC
8
NC
NC
Functional Description










Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for
industrial environment.
Supports 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps, full/half-duplex.
Auto MDI/MDIX.
100Base-FX: Multi mode/Single mode SC or ST type. 100Base-BX: WDM Multi
mode/Single mode SC type.
SFP socket for fiber optic expansion.
Supports 1024 MAC addresses. Provides 448K bits memory buffer.
Alarms for power and port link failure by relay output 1A @ 250VAC.
Power consumption: 6W Max.
Power Supply: Redundant 12~48VDC Terminal Block power inputs.
-20°C to 60°C (-4°F to 140°F) operating temperature range.
Supports DIN-Rail or Panel Mounting installation.
The fiber port pinouts
The Tx (transmit) port of device I is connected to the Rx (receive)
port of device II, and the Rx (receive) port of device I to the Tx
(transmit) port of device II.
The WDM 100Base-BX Connections
Assembly, Startup, and Dismantling



Assembly: Place the device on the DIN rail from above using the slot. Push the
front of the device toward the mounting surface until it audibly snaps into place.
Startup: Connect the supply voltage to start up the device via the terminal block.
Dismantling: Pull out the lower edge and then remove the device from the DIN
rail.
The fiber port pinouts
Only one Single mode or Multi mode optical fiber is required to
transmit and receive data.
The 100Base-FX/BX SFP Socket Connections
The SFP socket for fiber optic expansion.
www.balluff.com
2
Nr. 914486 EN Edition G16 Replaces Edition J14  Subject to modification
The 100Base-FX Connections
Download PDF