1U Series Standalone DVR User’s Manual
1
Table of Contents
1
FEATURES AND SPECIFICATIONS................................................................ 10
1.1
Overview ............................................................................................................................................... 10
1.2
Features ................................................................................................................................................ 10
1.3
Specifications ....................................................................................................................................... 11
1.3.1
Standard 1U Series ........................................................................................................................ 11
1.3.2
Simple Entry Level Series ............................................................................................................. 15
1.3.3
Simple Lite Series ........................................................................................................................... 18
2
OVERVIEW AND CONTROLS ......................................................................... 22
2.1
Front Panel ........................................................................................................................................... 22
2.1.1
Standard 1U Series ........................................................................................................................ 22
2.1.2
Simple Entry Level Series and Simple Lite Series..................................................................... 22
2.2
Rear Panel............................................................................................................................................ 24
2.2.1
Standard 1U Series ........................................................................................................................ 24
2.2.2
Simple Entry Level Series ............................................................................................................. 24
2.2.3
Simple Lite Series ........................................................................................................................... 26
2.3
Connection Sample ............................................................................................................................. 26
2.3.1
Standard 1U series......................................................................................................................... 26
2.3.2
Simple Entry Level Series ............................................................................................................. 27
2.3.3
Simple Lite Series ........................................................................................................................... 28
2.4
Remote Control.................................................................................................................................... 29
2.5
Mouse Control...................................................................................................................................... 31
2.6
Virtual Keyboard & Front Panel ......................................................................................................... 32
2.6.1
Virtual Keyboard.............................................................................................................................. 32
2.6.2
Front Panel ...................................................................................................................................... 32
2
3
INSTALLATION AND CONNECTIONS............................................................. 33
3.1
Check Unpacked DVR ........................................................................................................................ 33
3.2
About Front Panel and Real Panel ................................................................................................... 33
3.3
HDD Installation ................................................................................................................................... 33
3.4
Connecting Power Supply .................................................................................................................. 34
3.5
Connecting Video Input and Output Devices .................................................................................. 34
3.5.1
Connecting Video Input.................................................................................................................. 34
3.5.2
Connecting Video Output............................................................................................................... 35
3.6
Connecting Audio Input & Output, Bidirectional Audio .................................................................. 37
3.6.1
Audio Input....................................................................................................................................... 37
3.6.2
Audio Output.................................................................................................................................... 38
3.7
Alarm Input and Output Connection ................................................................................................. 39
3.7.1
Alarm Input and Output Details..................................................................................................... 41
3.7.2
Alarm Input Port .............................................................................................................................. 42
3.7.3
Alarm Output Port ........................................................................................................................... 43
3.8
RS232.................................................................................................................................................... 43
3.9
RS485.................................................................................................................................................... 44
3.10
Other Interfaces ................................................................................................................................... 45
3.10.1
Standard 1U Series.................................................................................................................... 45
3.10.2
Simple entry level series ........................................................................................................... 45
3.10.3
Simple lite series ........................................................................................................................ 45
4
OVERVIEW OF NAVIGATION AND CONTROLS ............................................ 47
4.1
4.1.1
Login, Logout & Main Menu ............................................................................................................... 47
Login ................................................................................................................................................. 47
3
4.1.2
Main Menu ....................................................................................................................................... 47
4.1.3
Logout............................................................................................................................................... 48
4.1.4
Auto Resume after Power Failure ................................................................................................ 48
4.1.5
Replace Button Battery .................................................................................................................. 48
4.1.6
Preview Zoom Function ................................................................................................................. 49
4.2
Manual Record..................................................................................................................................... 49
4.2.1
Live Viewing..................................................................................................................................... 49
4.2.2
Manual record.................................................................................................................................. 49
4.3
Search & Playback .............................................................................................................................. 51
4.3.1
Search Menu ................................................................................................................................... 51
4.3.2
Basic Operation............................................................................................................................... 52
4.3.3
Calendar........................................................................................................................................... 54
4.4
Schedule ............................................................................................................................................... 54
4.4.1 Schedule Menu .................................................................................................................................... 54
4.4.2
Snapshot .......................................................................................................................................... 55
4.4.3
Image FTP ....................................................................................................................................... 56
4.5
Detect .................................................................................................................................................... 57
4.5.1 Go to Detect Menu............................................................................................................................... 57
4.5.2 Motion Detect........................................................................................................................................ 57
4.5.3 Video Loss............................................................................................................................................. 59
4.5.4 Camera Masking.................................................................................................................................. 60
4.6
Alarm Setup and Alarm Activation .................................................................................................... 60
4.6.1
Go to alarm setup interface ........................................................................................................... 61
4.6.2
Alarm setup...................................................................................................................................... 61
4.7
Backup .................................................................................................................................................. 63
4.7.1 Detect Device....................................................................................................................................... 63
4.7.1
4.8
Backup.............................................................................................................................................. 63
PTZ Control and Color Setup ............................................................................................................ 64
4.8.1 Cable Connection ................................................................................................................................ 64
4.8.2 PTZ Setup ............................................................................................................................................. 64
4.8.3 3D Intelligent Positioning Key............................................................................................................ 66
4.9
Preset/ Patrol/Pattern/Scan................................................................................................................ 66
4
4.9.1Preset Setup ......................................................................................................................................... 67
4.9.2 Activate Preset..................................................................................................................................... 68
4.9.3 Patrol setup (Tour Setup)................................................................................................................... 68
4.9.4 Activate Patrol (tour) ........................................................................................................................... 68
4.9.5 Pattern Setup ....................................................................................................................................... 68
4.9.6 Activate Pattern Function ................................................................................................................... 68
4.9.7 Auto Scan Setup ................................................................................................................................. 69
4.9.8 Activate Auto Scan.............................................................................................................................. 69
4.10
5
Flip ......................................................................................................................................................... 69
UNDERSTANDING OF MENU OPERATIONS AND CONTROLS ................... 70
5.1
Menu Tree ............................................................................................................................................ 70
5.2
Main Menu ............................................................................................................................................ 71
5.3
Setting ................................................................................................................................................... 72
5.3.1
General............................................................................................................................................. 72
5.3.2
Encode ............................................................................................................................................. 73
5.3.3
Schedule .......................................................................................................................................... 74
5.3.4
RS232............................................................................................................................................... 75
5.3.5
Network ............................................................................................................................................ 75
5.3.6
Alarm................................................................................................................................................. 81
5.3.7
Detect ............................................................................................................................................... 81
5.3.8
Pan/Tilt/Zoom .................................................................................................................................. 81
5.3.9
Display.............................................................................................................................................. 82
5.3.10
Default.......................................................................................................................................... 84
5.4
Search ................................................................................................................................................... 84
5.5
Advanced .............................................................................................................................................. 84
5.5.1
HDD Management .......................................................................................................................... 85
5.5.2
Abnormity ......................................................................................................................................... 86
5.5.3
Alarm Output.................................................................................................................................... 86
5.5.4
Manual Record ................................................................................................................................ 87
5.5.5
Account............................................................................................................................................. 87
5.5.6
Auto Maintain................................................................................................................................... 88
5.5.7
TV Adjust.......................................................................................................................................... 88
5.5.8
Card Overlay.................................................................................................................................... 89
5
5.5.9
5.6
Config File Backup.......................................................................................................................... 90
Information............................................................................................................................................ 91
5.6.1
HDD Information ............................................................................................................................. 91
5.6.2
BPS ................................................................................................................................................... 92
5.6.3
Log .................................................................................................................................................... 92
5.6.4
Version ............................................................................................................................................. 93
5.6.5
Online Users .................................................................................................................................... 93
5.7
6
Shutdown .............................................................................................................................................. 94
ABOUT AUXILIARY MENU .............................................................................. 95
6.1
Go to Pan/Tilt/Zoom Menu ................................................................................................................. 95
6.1.1
6.2
3D Intelligent Positioning Key ....................................................................................................... 95
Preset /Patrol / Pattern /Border Function....................................................................................... 96
6.2.1
Preset Setup .................................................................................................................................... 97
6.2.2
Activate Preset ................................................................................................................................ 97
6.2.3
Patrol Setup ..................................................................................................................................... 97
6.2.4
Activate Patrol ................................................................................................................................. 97
6.2.5
Pattern Setup................................................................................................................................... 97
6.2.6
Activate Pattern Function............................................................................................................... 98
6.2.7
Border Setup.................................................................................................................................... 98
6.2.8
Activate Border Function ............................................................................................................... 98
6.2.9
Flip .................................................................................................................................................... 98
7
WEB OPERATION.......................................................................................... 100
7.1
Network Connection.......................................................................................................................... 100
7.2
Login .................................................................................................................................................... 100
7.2.1
Real-time Monitor.......................................................................................................................... 103
7.2.2
PTZ ................................................................................................................................................. 104
7.2.3
Color ............................................................................................................................................... 107
7.2.4
Picture Path and Record Path .................................................................................................... 107
7.3
7.3.1
Configure ............................................................................................................................................ 108
System Information....................................................................................................................... 108
6
7.3.2
System Configuration ................................................................................................................... 110
7.3.3
Advanced ....................................................................................................................................... 128
7.3.4
Additional Function ....................................................................................................................... 134
7.4
Search ................................................................................................................................................. 136
7.5
Alarm ................................................................................................................................................... 140
7.6
About ................................................................................................................................................... 141
7.7
Log out ................................................................................................................................................ 141
7.8
Un-install Web Control...................................................................................................................... 142
8
PROFESSIONAL SURVEILLANCE SYSTEM ................................................ 143
9
FAQ................................................................................................................. 144
APPENDIX A HDD CAPACITY CALCULATION ................................................. 149
APPENDIX B COMPATIBLE USB DRIVE LIST .................................................. 150
APPENDIX C COMPATIBLE CD/DVD BURNER LIST........................................ 151
APPENDIX D COMPATIBLE SATA HDD LIST ................................................... 152
APPENDIX E COMPATIBLE DISPLAYER LIST ................................................. 154
APPENDIX F
EARTHING.................................................................................... 155
7
Welcome
Thank you for purchasing our DVR!
This operating manual is designed to be a reference tool for the installation and operation of your
system.
Here you can find information about this series DVR features and functions, as well as a detailed
menu tree.
Before installation and operation please read the following safeguards and warnings carefully!
8
Important Safeguards and Warnings
1.Electrical safety
All installation and operation here should conform to your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2.Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3.Installation
Keep upwards. Handle with care.
Do not apply power to the DVR before completing installation.
Do not place objects on the DVR
4.Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5.Environment
The DVR should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
This series product shall be transported, storage and used in the environment ranging from 0℃
to 40 ℃
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
9
1 FEATURES AND SPECIFICATIONS
1.1 Overview
This series product is an excellent digital monitor product. It adopts embedded Linux OS to
maintain reliable operation. Popular H.264 compression algorithm and G.711 audio compression
technology realize high quality, low bit stream. Unique frame by frame play function is suitable for
detailed analysis. It has various functions such as record, playback, monitor at the same time
and can guarantee audio video synchronization. This series product has advanced technology
and strong network data transmission function.
This series device adopts embedded design to achieve high security and reliability. It can work in
the local end, and at the same time, when connecting it to the professional surveillance software
(PSS), it can connect to security network to realize strong network and remote monitor function.
This series product can be widely used in various areas such as banking, telecommunication,
electric power, interrogation, transportation, intelligent resident zone, factory, warehouse,
resources, and water conservancy.
1.2 Features
This series product has the following features:
z Real-time monitor
It has analog output port, VGA port and HDMI port. You can use monitor or displayer to realize
surveillance function.
System supports TV/VGA/HDMI output at the same time.
z Storage function
Special data format to guarantee data security and can avoid vicious data modification.
z Compression format
Support multiple-channel audio and video. An independent hardware decodes the audio and
video signal from each channel to maintain video and audio synchronization.
z Backup function
Support backup operation via USB port (such as flash disk, portable HDD, burner)
Client-end user can download the file to local HDD to backup via network.
z Record playback function
Support each channel real-time record independently, and at the same time it can support search,
forward play, network monitor, record search, download and etc.
Support various playback modes: slow play, fast play, backward play and frame by frame play.
Support time title overlay so that you can view event accurate occurred time
Support specified zone enlargement.
z
Network operation
10
Support network remote real-time monitor, remote record search and remote PTZ control.
z Alarm activation function
Several relay alarm outputs to realize alarm activation and on-site light control.
The alarm input port and output has the protection circuit to guarantee device safety.
z Communication port
RS485 port can realize alarm input and PTZ control.
RS232 port can connect to keyboard to realize central control, and can also connect to PC COM
to upgrade system and realize maintenance, and matrix control.
Standard Ethernet port can realize network access function.
z PTZ control
Support PTZ decoder via RS485.
Support various decode protocols to allow the PTZ to control the speed dome.
z Intelligent operation
Mouse operation function
In the menu, support copy and paste setup function
Slight function differences may be found due to different series.
1.3 Specifications
1.3.1 Standard 1U Series
Parameter
System
Compression
Standard
Main
Processor
OS
System
Resources
Interface
Input
Devices
Input
Method
Shortcut
Function
Video
Compressio
n
Audio
Compressio
n
Video Input
4-ch
8-ch
16-ch
High-performance industrial embedded micro controller
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback
and network operation simultaneously
User-friendly graphical user interface
Front panel, USB mouse, remote control
Arabic number, English character, donation and extension Chinese
(optional)
Copy/paste operation, USB mouse right-key shortcut menu, double click
USB mouse to switch screen.
H.264
G.711A
4-CH composite video
input: (NTSC/PAL)
BNC (1.0VP- P, 75Ω)
B
B
8-CH composite video
input: (NTSC/PAL)
BNC (1.0VP- P, 75Ω)
B
B
16-CH composite
video input:
(NTSC/PAL) BNC
(1.0VP- P, 75Ω)
B
B
11
Video monitor
Video
Output
1-ch PAL/NTSC, BNC (1.0VP- P, 75Ω) composite video signal output.
1-ch VGA output.
1-ch HDMI output.
Support TV/VGA/HDMI video output at the same time.
Video
Standard
PAL (625 line, 50f/s), NTSC (525 line, 60f/s)
Record
Speed
Video
Partition
Monitor
Touring
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s
per channel
1/4 windows(Optional)
1/4/9 windows
1/4/9 /16 windows
Support monitor tour functions such as alarm, motion detection, and
schedule auto control.
PAL(625TV Line,50f/s),NTSC(525TV line,60f/s)
Real-time monitor:
D1 704×576/704×480
Resolution
(PAL/NTSC
)
Playback:
1/16-ch: D1 704×576/704×480 (6f/s, when other channels’ resolution
are all CIF, the first channel and the ninth channel can support 25f/s.) ,
CIF 352×288/ 352×240 , QCIF 176×144/176×120
Other channels CIF 352×288/ 352×240 、QCIF 176×144/176×120.
Support dual streams: extra stream resolution QCIF 176×144/176×120
Motion
Detection
6-level image quality (Adjustable)
Image
Quality
Privacy
mask
Image
Information
Support one privacy mask of user-defined size in full screen.
Support max 4 zones.
TV Adjust
Adjust TV output zone suitable to anamorphic video.
Channel
Lock
Cover secret channel with blue screen though system is encoding
normally.
Screen-lock function to prevent unauthorized user seeing secret video.
Channel name, recording status, screen lock status, video loss status
and motion detection status are shown on the bottom left of display
screen.
Hue, brightness, contrast, saturation and gain setup for each channel.
Channel
Information
Color
Configuratio
n
Audio
Audio Input
Hard disk
Zone setup: support max 396(22×18) zones.
Support various sensitivities.
Audio
Output
Bidirectional
Audio
Hard Disk
Hard Disk
Occupation
Channel information, time information and privacy mask zone.
4-ch 200-2000mv
10KΩ(BNC)
8-ch 200-2000mv
10KΩ(BNC)
4-ch 2002000mv 10KΩ
(BNC)
1-ch audio output 200-3000mv 5KΩ(BNC)
Reuse the first channel audio input port to realize bidirectional talk
function.
1 built-in SATA port. Support 1 HDD.
Audio:PCM 28.8MByte/h
Video:56-900MByte/h
12
Recording
Mode
Record and
playback
Recording
Length
Playback
Repeat
Way
Record
Search
Playback
Mode
Various File
Switch
Ways
Multichannel
Playback
Window
Zoom
Partial
Enlargemen
t
Backup
function
Backup
Mode
Network
Function
Network
control
Motion
Detection and
Alarm
Motion
Detection
Video Loss
External
Alarm
Manual
Alarm
Control
Manual recording, motion detection recording, schedule recording and
alarm recording
Priority: Manual recording> alarm recording>motion detection
recording>schedule recording.
1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various search engines such as time, type and channel.
Various fast play, slow play speeds, manual frame by frame playback
and reverse play mode.
Can switch to previous or next file or any file in current play list.
Can switch to file on other channel of the same time. (If there is a file)
Support file continuous play, when file is end system auto plays the next
file in the current channel
There are two playback modes: 4-ch and full-channel. In 4-ch
playback mode, you can select the 1/2/3/4-ch playback according to
your requirement. In full-channel mode, system can playback in full
channels. Please note the 4-ch has no full-channel playback mode.
Switch between self-adaptive screen/full screen when playback
When in one-window full-screen playback mode, you can select any zone
to activate partial enlargement function.
HDD backup
Support peripheral USB backup device. (Flash disk, portable disk and
etc.)
Support USB burner (extension function).
Support network download and backup
View monitor channel remotely.
DVR configuration through client-end and web browser
Upgrade via client or browser to realize remote maintenance.
View alarm information such as external alarm, motion detection and
video loss via client.
Support network PTZ lens control
File download backup and playback
Multiple devices share information via corresponding software such as
professional surveillance software (PSS)
Duplex transparent COM
Network alarm input and output
Bidirectional audio.
Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones.
Various sensitivity levels.
Alarm can activate record or external alarm or screen message prompt.
Alarm can activate external alarm or screen message prompt.
Support record activation function or activate external alarm or screen
message in specified period.
Enable or disable alarm input channel
Support analog alarm signal to specific alarm output channel.
13
Alarm Input
Interface
Alarm
Output
Alarm Relay
USB
Interface
Network
connection
RS485
RS232
System
Information
Hard Disk
Information
Data
Stream
Statistics
Log
statistics
Version
On-line user
User
Management
User
Manageme
nt
Password
Authenticati
on
Upgrade
Login, Logout and Shutdown
General
Parameter
Power
Power
Consumptio
n
Working
Temperatur
e
Working
Humidity
Air
Pressure
Dimension
Weight
4-ch alarm input(You
can set normal open or
normal close type to
select the alarm type. )
8-ch alarm input(You
can set normal open or
normal close type to
select the alarm type. )
16-ch alarm input
(You can set
normal open or
normal close
type to select the
alarm type. )
3-channel relay output.
30VDC 2A,125VAC
2 USB 2.0 ports.
1A(activation alarm )
RJ45 10M/100M self-adaptable Ethernet port
PTZ control port
Support various PTZ control protocols.
Ordinary COM (Debug),keyboard connection and transparent serial
port(COM input and output via network )
Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files.
Support various search engines such as time and type.
Display version information: channel amount, alarm input and output
amount, system version and release date.
Display current on-line user
Multi-lever user management; various management modes
Integrated management for local user, serial port user and network user.
Configurable user power.
Support user /group and its corresponding rights modification.
No limit to the user or group amount.
Password modification
Administrator can modify other user’s password.
Account lock strategy
Five times login failure in thirty minutes may result in account lock.
Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout
/shutdown/ restart.
Right authentication when shut down to make sure only those proper
people can turn off DVR
DC +12V/3.3A
12W (Exclude HDD)
0℃-+55℃
10%-90%
86kpa-106kpa
375 x285 x45mm
3.25KG(Exclude HDD)
14
Installation
Mode
Desktop installation
1.3.2 Simple Entry Level Series
Parameter
System
Compression
Standard
Main
Processor
OS
System
Resources
Interface
Input
Devices
Input
Method
Shortcut
Function
Video
Compressio
n
Audio
Compressio
n
Video Input
4-ch
8-ch
16-ch
High-performance industrial embedded micro controller
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback
and network operation simultaneously
User-friendly graphical user interface
Front panel, USB mouse, remote control
Arabic number, English character, donation and extension Chinese
(optional)
Copy/paste operation, USB mouse right-key shortcut menu, double click
USB mouse to switch screen.
H.264
G.711A
16-CH composite
video input:
(NTSC/PAL) BNC
(1.0VP- P, 75Ω)
1-ch PAL/NTSC, BNC (1.0VP- P, 75Ω) composite video signal output.
1-ch VGA output.
1-ch HDMI output.
Support TV/VGA/HDMI video output at the same time.
4-CH composite video
input: (NTSC/PAL)
BNC (1.0VP- P, 75Ω)
B
B
8-CH composite video
input: (NTSC/PAL) BNC
(1.0VP- P, 75Ω)
B
B
B
Video monitor
Video
Output
Video
Standard
Record
Speed
Video
Partition
Monitor
Touring
B
PAL (625 line, 50f/s), NTSC (525 line, 60f/s)
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s per
channel
1/4 windows(Optional)
1/4/9 windows
1/4/9 /16 windows
Support monitor tour functions such as alarm, motion detection, and
schedule auto control.
PAL(625TV Line,50f/s),NTSC(525TV line,60f/s)
Real-time monitor:
D1 704×576/704×480
Resolution
(PAL/NTSC
)
Playback 1/4-ch:
Playback 1/8-ch:
Playback:
D1 704×576/704×480
D1 704×576/704×
1/16-ch: D1
(6f/s, when other
704×576/704×480
480 (6f/s),CIF 352
(6f/s, when other
×288/ 352×240 ,QCIF channels’ resolution
are all CIF, the first
channels’ resolution
176×144/176×120.
channel and the ninth
are all CIF, the first
channel can support
channel and the ninth
25f/s.), CIF 352×288/
channel can support
352×240, QCIF
25f/s.) , CIF 352×288/
176×144/176×120.
352×240 , QCIF
176×144/176×120.
Support dual streams: extra stream resolution QCIF 176×144/176×120
15
Motion
Detection
Support one privacy mask of user-defined size in full screen.
Support max 4 zones.
TV Adjust
Adjust TV output zone suitable to anamorphic video.
Channel
Lock
Channel
Information
Color
Configuratio
n
Cover secret channel with blue screen though system is encoding normally.
Screen-lock function to prevent unauthorized user seeing secret video.
Channel name, recording status, screen lock status, video loss status and
motion detection status are shown on the bottom left of display screen.
Hue, brightness, contrast, saturation and gain setup for each channel.
Audio Input
Audio
Output
Bidirectional
Audio
Hard Disk
Hard Disk
Occupation
Recording
Mode
Record and
playback
Recording
Length
Playback
Repeat
Way
Record
Search
Playback
Mode
Various File
Switch
Ways
Multichannel
Playback
Backup
function
6-level image quality (Adjustable)
Image
Quality
Privacy
mask
Image
Information
Audio
Hard disk
Zone setup: support max 396(22×18) zones.
Support various sensitivities.
Window
Zoom
Partial
Enlargemen
t
Backup
Mode
Channel information, time information and privacy mask zone.
2-ch 200-2000mv
10KΩ(BNC)
4-ch 200-2000mv
10KΩ(BNC)
4-ch 2002000mv 10KΩ
(BNC)
1-ch audio output 200-3000mv 5KΩ(BNC)
Reuse the first channel audio input port to realize bidirectional talk function.
1 built-in SATA port. Support 1 HDD.
Audio:PCM 28.8MByte/h
Video:56-900MByte/h
Manual recording, motion detection recording, schedule recording and
alarm recording
Priority: Manual recording> alarm recording>motion detection
recording>schedule recording.
1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various search engines such as time, type and channel.
Various fast play, slow play speeds, manual frame by frame playback and
reverse play mode.
Can switch to previous or next file or any file in current play list.
Can switch to file on other channel of the same time. (If there is a file)
Support file continuous play, when file is end system auto plays the next file
in the current channel
There are two playback modes: 4-ch and full-channel. In 4-ch playback
mode, you can select the 1/2/3/4-ch playback according to your
requirement. In full-channel mode, system can playback in full channels.
Please note the 4-ch has no full-channel playback mode.
Switch between self-adaptive screen/full screen when playback
When in one-window full-screen playback mode, you can select any zone to
activate partial enlargement function.
HDD backup
Support peripheral USB backup device. (Flash disk, portable disk and etc.)
16
Network
Function
Network
control
Motion
Detection and
Alarm
Motion
Detection
Video Loss
External
Alarm
Manual
Alarm
Control
Alarm Input
Interface
Alarm
Output
Alarm Relay
USB
Interface
Network
connection
RS485
Support USB burner (extension function).
Support network download and backup
View monitor channel remotely.
DVR configuration through client-end and web browser
Upgrade via client or browser to realize remote maintenance.
View alarm information such as external alarm, motion detection and video
loss via client.
Support network PTZ lens control
File download backup and playback
Multiple devices share information via corresponding software such as
professional surveillance software (PSS)
Duplex transparent COM
Network alarm input and output
Bidirectional audio.
Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones.
Various sensitivity levels.
Alarm can activate record or external alarm or screen message prompt.
Alarm can activate external alarm or screen message prompt.
Support record activation function or activate external alarm or screen
message in specified period.
Enable or disable alarm input channel
Support analog alarm signal to specific alarm output channel.
4-ch alarm input(You
can set normal open or
normal close type to
select the alarm type. )
8-ch alarm input(You can
set normal open or normal
close type to select the
alarm type. )
1-channel relay output.
3-channel relay output.
30VDC 2A,125VAC
2 USB 2.0 ports.
1A(activation alarm )
RJ45 10M/100M self-adaptable Ethernet port
PTZ control port
Support various PTZ control protocols.
N/A
RS232
System
Information
Hard Disk
Information
Data
Stream
Statistics
Log
statistics
Version
User
Management
On-line user
User
Manageme
nt
16-ch alarm input
(You can set
normal open or
normal close
type to select the
alarm type. )
3-channel relay
output.
Ordinary COM
(Debug),keyboard
connection and
transparent serial
port(COM input and
output via network )
Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files.
Support various search engines such as time and type.
Display version information: channel amount, alarm input and output
amount, system version and release date.
Display current on-line user
Multi-lever user management; various management modes
Integrated management for local user, serial port user and network user.
Configurable user power.
17
Password
Authenticati
on
Upgrade
Login, Logout and Shutdown
General
Parameter
Power
Power
Consumptio
n
Working
Temperatur
e
Working
Humidity
Air
Pressure
Dimension
Weight
Installation
Mode
Support user /group and its corresponding rights modification.
No limit to the user or group amount.
Password modification
Administrator can modify other user’s password.
Account lock strategy
Five times login failure in thirty minutes may result in account lock.
Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout
/shutdown/ restart.
Right authentication when shut down to make sure only those proper
people can turn off DVR
DC +12V/3.3A
12W (Exclude HDD)
0℃-+55℃
10%-90%
86kpa-106kpa
325×242×55mm (The height here includes the floor mat.)
2.5KG(Exclude HDD)
Desktop installation
1.3.3 Simple Lite Series
Parameter
System
Compression
Standard
Main
Processor
OS
System
Resources
Interface
Input
Devices
Input
Method
Shortcut
Function
Video
Compressio
n
Audio
Compressio
n
Video Input
Video
Output
4-ch
High-performance industrial embedded micro controller
Embedded LINUX
Multiplex operations: Multiple-channel record, multiple-channel playback
and network operation simultaneously
User-friendly graphical user interface
Front panel, USB mouse, remote control
Arabic number, English character, donation and extension Chinese
(optional)
Copy/paste operation, USB mouse right-key shortcut menu, double click
USB mouse to switch screen.
H.264
G.711A
4-CH composite video input: (NTSC/PAL) BNC (1.0VP- P, 75Ω)
1-ch PAL/NTSC, BNC (1.0VP- P, 75Ω) composite video signal output.
1-ch VGA output.
Support TV/VGA video output at the same time.
B
B
18
Video monitor
Video
Standard
Record
Speed
Video
Partition
Monitor
Touring
Resolution
(PAL/NTSC
)
PAL (625 line, 50f/s), NTSC (525 line, 60f/s)
Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s per
channel
1/4 windows(Optional)
Support monitor tour functions such as alarm, motion detection, and
schedule auto control.
PAL(625TV Line,50f/s),NTSC(525TV line,60f/s)
Real-time monitor:
D1 704×576/704×480
Playback:
1/4-ch: D1 704×576/704×480 (The first channel can support D1 25f/s, the
rest three channels can reach D1 6f/s.) , CIF 352×288/ 352×240 , QCIF
176×144/176×120.
Support dual streams: extra stream resolution QCIF 176×144/176×120
Audio
Hard disk
Support one privacy mask of user-defined size in full screen.
Support max 4 zones.
TV Adjust
Adjust TV output zone suitable to anamorphic video.
Channel
Lock
Channel
Information
Color
Configuratio
n
Audio Input
Audio
Output
Bidirectional
Audio
Hard Disk
Hard Disk
Occupation
Cover secret channel with blue screen though system is encoding normally.
Screen-lock function to prevent unauthorized user seeing secret video.
Channel name, recording status, screen lock status, video loss status and
motion detection status are shown on the bottom left of display screen.
Hue, brightness, contrast, saturation and gain setup for each channel.
Recording
Mode
Record and
playback
6-level image quality (Adjustable)
Image
Quality
Privacy
mask
Image
Information
Recording
Length
Playback
Repeat
Way
Record
Search
Playback
Mode
Channel information, time information and privacy mask zone.
2-ch 200-2000mv 10KΩ(BNC)
1-ch audio output 200-3000mv 5KΩ(BNC)
Reuse the first channel audio input port to realize bidirectional talk function.
1 built-in SATA port. Support 1 HDD.
Audio:PCM 28.8MByte/h
Video:56-900MByte/h
Manual recording, motion detection recording, schedule recording and
alarm recording
Priority: Manual recording> alarm recording>motion detection
recording>schedule recording.
1 to 120 minutes single record duration (Default setup is 60 minutes)
When hard disk is full, system can overwrite previous video file.
Various search engines such as time, type and channel.
Various fast play, slow play speeds, manual frame by frame playback and
reverse play mode.
19
Various File
Switch
Ways
Multichannel
Playback
Window
Zoom
Partial
Enlargemen
t
Backup
function
Network
Function
Motion
Detection and
Alarm
Interface
System
Information
Backup
Mode
Network
control
Motion
Detection
Video Loss
External
Alarm
Manual
Alarm
Control
Alarm Input
Alarm
Output
Alarm Relay
USB
Interface
Network
connection
RS485
RS232
Hard Disk
Information
Data
Stream
Statistics
Log
statistics
Version
On-line user
User
Management
User
Manageme
nt
Can switch to previous or next file or any file in current play list.
Can switch to file on other channel of the same time. (If there is a file)
Support file continuous play, when file is end system auto plays the next file
in the current channel
There is 1/2/3/4-channel playback.
Switch between self-adaptive screen/full screen when playback
When in one-window full-screen playback mode, you can select any zone to
activate partial enlargement function.
HDD backup
Support peripheral USB backup device. (Flash disk, portable disk and etc.)
Support USB burner (extension function).
Support network download and backup
View monitor channel remotely.
DVR configuration through client-end and web browser
Upgrade via client or browser to realize remote maintenance.
View alarm information such as motion detection and video loss via client.
File download backup and playback
Multiple devices share information via corresponding software such as
professional surveillance software (PSS)
Bidirectional audio.
Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones.
Various sensitivity levels.
Alarm can activate record or external alarm or screen message prompt.
Alarm can activate screen message prompt.
N/A
N/A
N/A
N/A
N/A
2 USB 2.0 ports.
RJ45 10M/100M self-adaptable Ethernet port
N/A
N/A
Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files.
Support various search engines such as time and type.
Display version information: channel amount, system version and release
date.
Display current on-line user
Multi-lever user management; various management modes
Integrated management for local user, serial port user and network user.
Configurable user power.
Support user /group and its corresponding rights modification.
No limit to the user or group amount.
20
Password
Authenticati
on
Upgrade
Login, Logout and Shutdown
General
Parameter
Power
Power
Consumptio
n
Working
Temperatur
e
Working
Humidity
Air
Pressure
Dimension
Weight
Installation
Mode
Password modification
Administrator can modify other user’s password.
Account lock strategy
Five times login failure in thirty minutes may result in account lock.
Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following options: Logout
/shutdown/ restart.
Right authentication when shut down to make sure only those proper
people can turn off DVR
DC +12V/3.3A
12W (Exclude HDD)
0℃-+55℃
10%-90%
86kpa-106kpa
325×242×55mm
2.5KG(Exclude HDD)
Desktop installation
21
2 Overview and Controls
This section provides information about front panel and rear panel. When you install this series
DVR for the first time, please refer to this part first.
2.1 Front Panel
This series product has two types of front panels.
2.1.1 Standard 1U Series
The front panel is shown as in Figure 2-1.
Figure 2-1
2.1.2 Simple Entry Level Series and Simple Lite Series
The simple entry level and simple lite series is shown as in Figure 2-2.
Figure 2-2
Please refer to the following sheet for front panel button information.
Name
Icon
Power button, press this button for three seconds to boot up
or shut down DVR.
Power button
Shift
Function
Shift
In textbox, click this button to switch between numeral,
English(Small/Capitalized),donation and etc.
Activate current control, modify setup, and then move up
and down.
Up/1
Down/4
S、T
Increase/decrease numeral.
Assistant function such as PTZ menu.
In text mode, input number 1/4 (English character G/H/I)
Shift current activated control,
Left/2
Right/3
W
ESC
ESC
X
When playback, click these buttons to control playback bar.
In text mode, input number 2(English character A/B/C)
/3(English character D/E/F)
Go to previous menu, or cancel current operation.
22
When playback, click it to restore real-time monitor mode.
Confirm current operation
Enter
ENTER
Go to default button
Go to menu
Record
REC
Multiple slow play speeds or normal playback.
In text mode, input number 8 (English character T/U/V).
Slow play/8
Assistant
Manually stop/start recording, working with direction keys
or numeral keys to select the recording channel.
One-window monitor mode, click this button to display
assistant function: PTZ control and image color.
Backspace function: in numeral control or text control, press
it for 1.5seconds to delete the previous character before the
cursor.
In motion detection setup, working with Fn and direction
keys to realize setup.
Fn
In text mode, click it to switch between numeral, English
character(small/capitalized) and etc.
Realize other special functions.
Fast play/7
_
Play
previous/0
Reverse/Pau
se/6
Various fast speeds and normal playback.
In text mode, input number 7 (English character P/Q/R/S).
W
f
Play Next/9
Play/Pause /5
f
USB port
In playback mode, playback the previous video
In text mode, input number 0.
In normal playback or pause mode, click this button to
reverse
playback
In reverse playback, click this button to pause playback.
In text mode, input number 6 (English character M/N/O)
In playback mode, playback the next video
In menu setup, go to down ward of the dropdown list.
In text mode, input number 9 (English character W/X/Y/Z)
In normal playback click this button to pause playback
In pause mode, click this button to resume playback.
In text mode, input number 5(English character J/K/L).
To connect USB storage device, USB mouse.
Network
abnormal
indication
light
Net
Network error occurs or there is no network connection, the
light becomes red to alert you.
HDD
abnormal
indication
light
HDD
HDD error occurs or HDD capacity is below specified
threshold value, the light becomes red to alert you.
Record light
1-16
System is recording or not. It becomes on when system is
recording.
23
IR Receiver
IR
Alarm
indication
light
Alarm
It is to receive the signal from the remote control.
Here you can view there is external alarm input or not. The
light becomes on when there is an external alarm. The light
become off when the external alarm stops.
2.2 Rear Panel
2.2.1 Standard 1U Series
Standard 1U series product rear panel is shown as below. See Figure 2-3 through Figure 2-5.
Figure 2-3 4-channel
Figure 2-4 8-channel
Figure 2-5 16-channel
Please refer to the following sheet for detailed information.
1
Video input
2
Audio input
3
Video CVBS output
4
Audio output
5
Network port
6
USB port
7
HDMI port
8
RS232 port
9
Video VGA output
10
Alarm input/alarm output/RS485 port
11
Power input port
12
Power button
2.2.2 Simple Entry Level Series
Simple entry level series real panel (4/8-channel) is shown as below. See Figure 2-6 and Figure
2-7.
24
Figure 2-6 4-channel
Figure 2-7 8-channel
Please refer to the following sheet for detailed information.
1
Video input
2
Audio input
3
Video CVBS output
4
Audio output
5
Network port
6
USB port
7
Video VGA output
8
Power input port
9
Alarm input/alarm output/RS485 port
10
Power button
Simple entry level series real panel (16-channel) is shown as below. See Figure 2-8.
Figure 2-8
Please refer to the following sheet for detailed information.
1
Video input
2
Audio input
3
Video CVBS output
4
Audio output
5
Network port
6
USB port
25
7
8
9
10
11
Video VGA output
RS232 port
Alarm input/alarm output/RS485 port
Power input port
Power button
2.2.3 Simple Lite Series
Simple lite series product rear panel is shown as in Figure 2-9.
Figure 2-9
Please refer to the following sheet for detailed information.
1
Video input
2
Audio input
3
Audio output
4
Video CVBS output
5
USB port
6
Network port
7
Video VGA output
8
Power input port
9
Power button
When connect the Ethernet port, please use straight cable to connect the PC and use the
crossover cable to connect to the switcher or router.
2.3 Connection Sample
2.3.1
Standard 1U series
Please refer to Figure 2-10 for standard 1U series product connection sample.
The following figure is based on one 8-channel series.
X281H
X
26
Figure 2-10
2.3.2
Simple Entry Level Series
Please refer to Figure 2-11 for simple entry level series product connection sample.
The following figure is based on one 4-channel series.
X281H
27
Figure 2-11
2.3.3
Simple Lite Series
Please refer to Figure 2-12 for simple lite series product connection sample.
The following figure is based on one 4-channel series.
X281H
28
Figure 2-12
2.4 Remote Control
The remote control interface is shown as in Figure 2-13.
Please note remote control is not our standard accessory and it is not included in the accessory
bag.
X28H
29
Figure 2-13
Serial Number
1
Name
Address
2
Multiple-window switch
3
0-9 number key
4
Record
5
Auxiliary key
6
Confirm /menu key
7
Cancel
8
Direction key
9
forward
10
Previous
11
Backward
12
Stop
13
Next
14
Slow play
15
Play/Pause
16
Fast play
Function
Click it to input device serial
number, so that you can control
it.
Please refer to the multiplewindow switch button in the front
panel (MULT)
Input password, channel or
switch channel.
Shift is the button to switch the
input method.
Please refer to the record in the
front panel.
Please refer to the Fn button in
the front panel.
Please refer to the ENTER
button in the front panel.
Please refer to the ESC button in
the front panel.
Please refer to the direction
buttons in the front panel.
Various forward speeds and
normal speed playback.
Please refer to the previous in
the front panel.
Various backward speeds and
normal speed playback.
Please refer to the stop button in
the front panel.
Please refer to the next button in
the front panel.
Please refer to the slow play
button in the front panel.
Please refer to the play/pause
button in the front panel.
Please refer to the fast play
30
button in the front panel.
2.5 Mouse Control
Left click
mouse
System pops up password input dialogue box if you have not logged in.
In real-time monitor mode, you can go to the main menu.
When you have selected one menu item, left click mouse to view menu
content.
Implement the control operation.
Modify checkbox or motion detection status.
Click combo box to pop up drop down list
In input box, you can select input methods. Left click the corresponding
button on the panel you can input numeral/English character
(small/capitalized). Here ← stands for backspace button. _ stands for space
button.
In English input mode: _stands for input a backspace icon and ← stands for
deleting the previous character.
In numeral input mode: _ stands for clear and ← stands for deleting the
previous numeral.
When input special sign, you can click corresponding numeral in the front
panel to input. For example, click numeral 1 you can input“/” , or you can click
the numeral in the on-screen keyboard directly.
Double left
click mouse
Implement special control operation such as double click one item in the file
list to playback the video.
In multiple-window mode, double left click one channel to view in full-window.
Double left click current video again to go back to previous multiple-window
mode.
31
Right click
mouse
Press
middle
button
Move
mouse
Drag mouse
In real-time monitor mode, pops up shortcut menu: one-window, four-window,
nine-window and sixteen-window, Pan/Tilt/Zoom, color setting, search,
record, alarm input, alarm output, main menu.
Among which, Pan/Tilt/Zoom and color setting applies for current selected
channel.
If you are in multiple-window mode, system automatically switches to the
corresponding channel.
The simple entry level series product does not support RS232 function.
The simple lite series product does not support RS232, alarm and PTZ
function.
Exit current menu without saving the modification.
In numeral input box: Increase or decrease numeral value.
Switch the items in the check box.
Page up or page down
Select current control or move control
Select motion detection zone
Select privacy mask zone.
2.6 Virtual Keyboard & Front Panel
2.6.1 Virtual Keyboard
The system supports two input methods: numeral input and English character (small and
capitalized) input.
Move the cursor to the text column, the text is shown as blue, input button pops up on the right.
Click that button to switch between numeral input and English input (capitalized and small), Use
> or < to shift between small character and capitalized character.
2.6.2 Front Panel
Move the cursor to the text column. Click Fn key and use direction keys to select number you
wanted. Please click enter button to input.
32
3 Installation and Connections
Note: All the installation and operations here should conform to your local
electric safety rules.
3.1 Check Unpacked DVR
When you receive the DVR from the forwarding agent, please check whether there is any visible
damage. The protective materials used for the package of the DVR can protect most accidental
clashes during transportation. Then you can open the box to check the accessories.
Please check the items in accordance with the list on the warranty card (Remote control is
optional). Finally you can remove the protective film of the DVR.
Note
Remote control is not a standard accessory and it is not included in the accessory bag.
3.2 About Front Panel and Real Panel
For detailed information of the function keys in the front panel and the ports in the rear panel,
please refer to the appendix for detailed information.
The model in the front panel is very important; please check according to your purchase order.
The label in the rear panel is very important too. Usually we need you to represent the serial
number when we provide the service after sales.
3.3 HDD Installation
This series DVR has only one SATA HDD. Please use HDD of 7200rpm or higher.
You can refer to the Appendix for recommended HDD brand.
Please follow the instructions listed below to install hard disk.
1. Loosen the screws of the
2. Fix four screws in the HDD
3. Place the HDD in accordance with
upper cover and side panel.
(Turn just three rounds).
the four holes in the bottom.
4. Turn the device upside down
and then turn the screws in
5. Fix the HDD firmly.
6. Connect the HDD cable and
power cable.
firmly.
33
7. Put the cover in accordance
8. Secure the screws in the
with the clip and then place the
rear panel and the side panel.
upper cover back.
Note:
z You can connect the HDD data cable and the power cable first and then fix the HDD in the
device.
z Please pay attention to the front cover. It adopts the vertical sliding design. You need to
push the clip first and then put down.
3.4 Connecting Power Supply
Please check input voltage and device power button match or not.
We recommend you use UPS to guarantee steady operation, DVR life span, and other peripheral
equipments operation such as cameras.
3.5 Connecting Video Input and Output Devices
Please note the following figure is based on the general series product.
3.5.1 Connecting Video Input
The video input interface is BNC. The input video format includes: PAL/NTSC BNC(1.0VP- P ,
75Ω. See Figure 3-1 through Figure 3-3.
The video signal should comply with your national standards.
The input video signal shall have high SNR, low distortion; low interference, natural color and
suitable lightness.
B
B
Guarantee the stability and reliability of the camera signal:
The camera shall be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
The camera and the DVR should have the same grounding to ensure the normal operation of the
camera.
Guarantee stability and reliability of the transmission line
Please use high quality, sound shielded BNC. Please select suitable BNC model according to the
transmission distance.
If the distance is too long, you should use twisted pair cable, and you can add video
compensation devices or use optical fiber to ensure video quality.
You should keep the video signal away from the strong electromagnetic interference, especially
the high tension current.
BT
Keep connection lugs in well contact
The signal line and shielded wire should be fixed firmly and in well connection. Avoid dry joint,
lap welding and oxidation.
BT
BT
34
Figure 3-1 Standard 1U Series
Figure 3-2 Simple Entry Level Series
Figure 3-3 Simple Lite Series
3.5.2 Connecting Video Output
Video output includes a BNC(PAL/NTSC
one HDMI output.
T
BNC(1.0VP- P, 75Ω)output , a VGA output and
35
The standard 1U series supports BNC, VGA and HDMI output at the same time. See Figure 3-4
The simple entry level and simple lite series supports BNC and VGA output at the same time .
See Figure 3-5 and Figure 3-6.
When you are using pc-type monitor to replace the monitor, please pay attention to the following
points:
z To defer aging, do not allow the pc monitor to run for a long time.
z Regular demagnetization will keep device maintain proper status.
z Keep it away from strong electromagnetic interference devices.
Using TV as video output device is not a reliable substitution method. You also need to reduce
the working hour and control the interference from power supply and other devices. The low
quality TV may result in device damage.
Figure 3-4 Standard 1U Series
Figure 3-5 Simple Entry Level Series
36
Figure 3-6 Simple Lite Series
3.6 Connecting Audio Input & Output, Bidirectional Audio
3.6.1 Audio Input
These series products adopt BNC port.
Due to high impedance of audio input, please use active sound pick-up. See Figure 3-7 to Figure
3-9.
Audio transmission is similar to video transmission. Try to avoid interference, dry joint, loose
contact and it shall be away from high tension current.
Figure 3-7 Standard 1U Series
37
Figure 3-8 Simple Entry Level Series
Figure 3-9 Simple Lite Series
3.6.2 Audio Output
The audio output signal parameter is usually over 200mv 1KΩ (BNC). It can directly connect to
low impedance earphone, active sound box or amplifier-drive audio output device.
If the sound box and the pick-up cannot be separated spatially, it is easy to arouse squeaking. In
this case you can adopt the following measures:
z Use better sound pick-up with better directing property.
z Reduce the volume of the sound box.
z Using more sound-absorbing materials in decoration can reduce voice echo and improve
acoustics environment.
z Adjust the layout to reduce happening of the squeaking.
Please refer to Figure 3-10 to Figure 3-12.
38
Figure 3-10 Standard 1U Series
Figure 3-11 Simple Entry Level Series
Figure 3-12 Simple Lite Series
3.7 Alarm Input and Output Connection
Please note simple lite series product does not support alarm function.
39
Please refer to the following sheet for alarm input and output connection. See Figure 3-13 and
Figure 3-14.
Figure 3-13 Standard 1U Series
Figure 3-14 Simple Entry Level Series
There are two alarm input types for you to select: normal open (NO) and normal close (NC).
1. Alarm input
a. Please make sure alarm input mode is grounding alarm input.
b. Grounding signal is needed for alarm input.
c. When you are connecting two DVRs or you are connecting one DVR and one other device,
please use a relay to separate them,
2. Alarm output
The alarm output port should not be connected to high power load directly (It shall be less than
1A) to avoid high current which may result in relay damage. Please use the co contactor to
realize the connection between the alarm output port and the load.
3. How to connect PTZ decoder
a. Ensure the decoder has the same grounding with DVR, otherwise you may not control the PTZ.
Shielded twisted wire is recommended and the shielded layer is used to connect to the grounding.
b. Avoid high voltage. Ensure proper wiring and some thunder protection measures.
40
c. For too long signal wires, 120Ω should be parallel connected between A, B lines on the far end
to reduce reflection and guarantee the signal quality.
d. “485 A, B” of DVR cannot parallel connect with “485 port” of other device.
e. The voltage between of A,B lines of the decoder should be less than 5v.
4. Please make sure the front-end device has soundly earthed.
Improper grounding may result in chip damage.
3.7.1 Alarm Input and Output Details
This series product has three types of alarm ports. Please refer to the following three figures for
detailed information. There are two alarm input types for you to select: normal open (NO) and
normal close (NC).
Important
Please refer to the specifications for the alarm input and output channel amount. Do not
merely count the alarm input and out channel amount according to the ports on the rear
panel.
One type of the alarm port is shown as in Figure 3-15.
AB Connection
port
Figure 3-15
You can refer to the following sheet for alarm input and output information.
Parameter
Grounding Alarm
Ground line
Alarm Input
1, 2, …, 8. It becomes valid in low voltage.
1-NO C,
2-NO C,
3-NO C
485 A/B
Three NO activation outputs.
485 communication port. They are used to control devices such as
PTZ. Please parallel connect 120Ω between A/B cables if there are
too many PTZ decoders.
One type of the alarm port is shown as in
Figure 3-16.
AB connection
port
41
Figure 3-16
You can refer to the following sheet for alarm input and output information.
Parameter
Grounding Alarm
Ground line
Alarm Input
1, 2, …, 16.. It becomes valid in low voltage.
1-NO C,
2-NO C,
3-NO C
485 A/B
Three NO activation outputs.
485 communication port. They are used to control devices such as
PTZ. Please parallel connect 120Ω between A/B cables if there are
too many PTZ decoders.
One type of the alarm port is shown as in Figure 3-17.
AB connection
port
Figure 3-17
You can refer to the following sheet for alarm input and output information.
Parameter
Grounding Alarm
Ground line
Alarm Input
1, 2, 3, 4. It becomes valid in low voltage.
NO C
One NO activation output.
485 A/B
485 communication port. They are used to control devices such as
PTZ. Please parallel connect 120Ω between A/B cables if there are
too many PTZ decoders.
3.7.2 Alarm Input Port
Please refer to the following sheet for more information. See Figure 3-18.
z Normal open or Normal close type
z Please parallel connect COM end and GND end of the alarm detector (Provide external
power to the alarm detector).
z Please parallel connect the Ground of the DVR and the ground of the alarm detector.
z Please connect the NC port of the alarm sensor to the DVR alarm input(ALARM)
z Use the same ground with that of DVR if you use external power to the alarm device.
42
Figure 3-18
3.7.3 Alarm Output Port
z
z
z
Provide external power to external alarm device.
To avoid overloading, please read the following relay parameters sheet carefully.
RS485 A/B cable is for the A/B cable of the PTZ decoder.
Relay Specification
Model:
JRC-27F
Material of the
touch
Silver
Rating
(Resistance
Load)
Rated switch capacity
30VDC 2A, 125VAC 1A
Maximum switch power
125VA 160W
Maximum switch voltage
250VAC, 220VDC
Maximum switch currency
Between touches with same
polarity
1A
Between touches with different
polarity
1000VAC 1minute
Between touch and winding
Between touches with same
polarity
3ms max
1000VAC 1minute
Insulation
Surge voltage
Length of open
time
1000VAC 1minute
1500V (10×160us)
Length of close
time
3ms max
Longevity
Mechanical
50×106 times (3Hz)
Electrical
200×103 times (0.5Hz)
Temperature
-40℃ ~+70℃
3.8 RS232
Please note simple entry level series product and simple lite series product does not
support RS232 function.
You can connect the DVR with POS or Keyboard through RS232.
With POS system, the DVR can communicate through RS232 and network. For the POS system, the
DVR can integrate the text content and even search the record through the info.
43
The series DVR also support NKB operation. You can operate the DVR from the keyboard controls
instead of using the control pad on the front panel of the unit.
To connect a NKB keyboard to the DVR:
1. Assemble the KBD keyboard according to the instructions in its accompanying installation manual.
2. Connect the KBD keyboard into one of the RS232 ports on the DVR or through network.
3.9 RS485
Please note simple Lite series product does not support PTZ function.
When the DVR receives a camera control command, it transmits that command up the coaxial cable
to the PTZ device. RS485 is a single-direction protocol; the PTZ device can’t return any data to the
unit. To enable the operation, connect the PTZ device to the RS485 (A,B) input on the DVR. See
Figure 3-19 through Figure 3-21.
X289H
Since RS485 is disabled by default for each camera, you must enable the PTZ settings first. This
series DVRs support multiple protocols such as Pelco-D, Pelco-P.
To connect PTZ devices to the DVR:
1. Connect RS485 A,B on the DVR rear panel.
2. Connect the other end of the cable to the proper pins in the connector on the camera.
3. Please follow the instructions to configure a camera to enable each PTZ device on the DVR.
485 Port
Figure 3-19 Standard 1U 4 /8-channel and simple entry level 8-channel
485 Port
Figure 3-20 Standard 1U 16-channel and simple entry level 16-channel
485 Port
Figure 3-21 Simple entry level 4-channel
44
3.10 Other Interfaces
There are still other interfaces on the DVR, such as USB ports.
3.10.1 Standard 1U Series
You can refer to the Figure 3-22 for more information.
Figure 3-22 Stand 1U Series
3.10.2 Simple entry level series
Please refer to the Figure 3-23 for more information.
Figure 3-23 Simple Entry Level Series
3.10.3 Simple lite series
45
Please refer to Figure 3-24 for more information.
Figure 3-24 Simple Lite Series
46
4 Overview of Navigation and Controls
Important
z Slight difference may be found in the interface. All the interfaces listed below are based on
the standard 1U series product.
z The simple entry level series product does not support RS232 function.
z The 8-channel simple entry level series product does not support schedule snapshot
function and etc. Please note for this series product, when you logged in the Web to operate
real-time monitor/network playback/network download, the local-end 8-channel playback is
disabled, and vice versa.
z The simple lite series product does not support RS232, alarm and PTZ function.
Before operation, please make sure:
z You have properly installed HDD and connect all the cable connections.
z The provided input power and the device power are matched.
z The external power shall be DC +12V 3.3A.
z Always use the stable current, if necessary UPS is a best alternative measure.
4.1 Login, Logout & Main Menu
4.1.1 Login
After system booted up, default video display is in multiple-window mode.
Click Enter or left click mouse, you can see the login interface. See Figure 4-1.
System consists of four accounts:
z
z
z
Username: admin. Password: admin. (administrator, local and network)
Username: 888888. Password: 888888. (administrator, local only)
Username: 666666. Passwords: 666666(Lower authority user who can only monitor, playback,
backup and etc.)
z Username: default. Password: default(hidden user)
You can use USB mouse, front panel, remote control or keyboard to input. About input method:
Click
to switch between numeral, English character (small/capitalized) and denotation.
Note:
For security reason, please modify password after you first login.
Within 30 minutes, three times login failure will result in system alarm and five times login failure
will result in account lock!
Figure 4-1
4.1.2
Main Menu
After you logged in, the system main menu is shown as below. See Figure 4-2.
There are total six icons: search, information, setting, backup, advanced and shutdown.
47
You can move the cursor to highlight the icon, and then double click mouse to enter the submenu.
Figure 4-2
4.1.3
Logout
There are two ways for you to log out.
One is from menu option:
In the main menu, click shutdown button, you can see an interface is shown as below. See
Figure 4-3.
Figure 4-3
There are several options for you. See Figure 4-4.
Figure 4-4
The other ways is to press power button on the front panel for at least 3 seconds, system will
stop all operations. Then you can click the power button in the rear panel to turn off the DVR.
4.1.4
Auto Resume after Power Failure
The system can automatically backup video and resume previous working status after power
failure.
4.1.5 Replace Button Battery
Please make sure to use the same battery model if possible.
48
We recommend replace battery regularly (such as one-year) to guarantee system time
accuracy.
Note:
Before replacement, please save the system setup, otherwise, you may lose the data
completely!
4.1.6 Preview Zoom Function
Move your mouse to the left top corner of the preview interface; you can see the preview
zoom button. See Figure 4-5. Left click the icon; you can see a hook icon. Now you have
enabled the preview zoom function. You can drag the mouse to zoom in the image.
Preview
zoom button
Figure 4-5
4.2 Manual Record
4.2.1
Live Viewing
After you logged in, the system is in live viewing mode. You can see system date, time and
channel name. If you want to change system date and time, you can refer to general settings
(Main Menu->Setting->General). If you want to modify the channel name, please refer to the
display settings (Main Menu->Setting->Display)
1
Recording status
3
Video loss
2
Motion detection
4
Camera lock
4.2.2 Manual record
Note:
You need to have proper rights to implement the following operations. Please make sure the
HDD has been properly installed.
4.2.2.1 Manual record menu
There are two ways for you to go to manual record menu.
z Right click mouse or in the main menu, Advanced->Manual Record.
z In live viewing mode, click record button in the front panel or record button in the remote
control.
Manual record menu is shown as in Figure 4-6.
49
4.2.2.2 Basic operation
There are three statuses: schedule/manual/stop. Please highlight icon“○” to select
corresponding channel.
z Manual: The highest priority. After manual setup, all selected channels will begin ordinary
recording.
z Schedule: Channel records as you have set in recording setup (Main Menu->Setting>Schedule)
z Stop: All channels stop recording.
Figure 4-6
4.2.2.3 Enable/disable record
Please check current channel status: “○” means it is not in recording status, “●” means it is in
recording status.
You can use mouse or direction key to highlight channel number. See Figure 4-7.
Figure 4-7
4.2.2.4 Enable all channel recording
Highlight ○ below All, you can enable all channel recording.
z All channel schedule record
Please highlight “ALL” after “Schedule”. See Figure 4-8.
When system is in schedule recording, all channels will record as you have previously set
(Main menu->Setting->Schedule).
The corresponding indication light in front panel will turn on.
50
Figure 4-8
z All channel manual record
Please highlight “ALL” after “Manual.” See Figure 4-9.
When system is in manual recording, all scheduled set up you have set in will be null ((Main
menu->Setting->Schedule)).
You can see indication light in front panel turns on, system begins manual record now.
Figure 4-9
4.2.2.5 Stop all channel recording
Please highlight “ALL” after “Stop”. See Figure 4-10.
System stops all channel recording no matter what mode you have set in the menu (Main
menu->Setting->Schedule)
Figure 4-10
4.3 Search & Playback
4.3.1 Search Menu
Click search button in the main menu, search interface is shown as below. See Figure 4-11.
Usually there are three file types:
z R: Regular recording file.
z A: External alarm recording file.
z M: Motion detection recording file
51
Playback control bar
Select playback mode
here: 4-ch or All-channel
Set search setup
here :( Time/Channel/Type)
Figure 4-11
Please refer to the following
Serial Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
sheet for more information.
Function
Play
Backward
Stop
Slow play
Fast play
Previous frame
Next frame
Volume
Previous file
Next channel
Next file
Previous channel
Search
Backup
4.3.2 Basic Operation
4.3.2.1 Playback
There are various search modes: video type, channel number or time. The system can max
display 128 files in one screen. You can use page up/down button to view if there are more
than one page.
Select the file name and double click mouse (or click enter button), you can view file content.
4.3.2.2 Playback Mode
52
There are two playback modes: 4-ch and all-channel. In 4-ch playback mode, you can select
the 1/2/3/4-ch playback according to your requirement. In all-channel mode, system can
playback in full channels. Please note the 4-ch has no all-channel playback mode.
4.3.2.3 Accurate playback
Input time (h/m/s) in the time column and then click playback button, system can operate
accurate playback.
4.3.2.4 Synchronized playback function when playback
During playback process, click numeral key, system can switch to the corresponding channel
video of the same time.
4.3.2.5 Digital zoom
When the system is in full-screen playback mode, drag your mouse in the screen to select a
section and then left click mouse to realize digital zoom. You can right click mouse to exit.
4.3.2.6 File backup and clip
System supports backup operation during search. You can draw a √ before file name
(multiple choices). Then click backup button (Button 14 in Figure 4-11).
If you want to clip a period of file, please playback the original file first. Click the
(Button
15 in Figure 4-11) at the start point (that is your new file beginning point). Drag the file to the
end point (that is your new file end point) and then click the
again. Click the backup
button (Button 14 in Figure 4-11) to save your current new file.
4.3.2.7 Slow playback and fast playback
Please refer to the following sheet for slow play and fast playback function.
Button
Fast play button Slow play button ►
Play/Pause►
Previous/next
Illustration
In playback mode, click this button to
switch between various fast play modes
such as fast play 1,fast play 2 and more.
In playback mode, click this button to
switch between various slow play modes
such as slow play 1 or slow play 2.
Remarks
Frame rate may
vary due to
different versions.
In slow playback mode, click this button
to switch between play/pause modes.
In playback mode, you can click │_ and
` to view previous or next video in
current channel.
4.3.2.8 Backward playback and frame by frame playback
Button
Backward play:
_ in playback
interface.
Manual playback
frame by frame.
Illustration
In normal playback mode, left click backward
play button_, system begins backward
playback.
Double click backward play button again,
system goes to pause mode.
Click pause button in normal playback mode,
you can use W│ and │X to view frame by
frame.
Remarks
When system is in
backward play or
frame by frame
playback mode, you
can click play
button►/ to go to
normal playback.
Note:
53
All the operations here (such as playback speed, channel, time and progress) have
relationship with hardware version. Some series DVRs do not support some functions or
playback speeds.
4.3.3 Calendar
Click calendar icon
in Figure 4-12, system pops up a calendar for your reference.
The highlighted date means there are record files in that day. You can click blue date to view
file list.
In Figure 4-12, there are video files in June 13th and 14th. Double click the date to view its
file list.
X30H
Figure 4-12
4.4 Schedule
After system booted up, it is in default 24-hour regular mode. You can set record type and
time in schedule interface.
4.4.1 Schedule Menu
In the main menu, from setting to schedule, you can go to schedule menu. See Figure 4-13.
Channel: Please select the channel number first. You can select “all” if you want to set for
the whole channels.
z Week day: There are eight options: ranges from Saturday to Sunday and all.
z Pre-record: System can pre-record the video before the event occurs into the file. The value
ranges from 1 to 30 seconds depending on the bit stream.
z Snapshot: You can enable this function to snapshoot image when alarm occurs.
z Record types: There are three types: regular, motion detection (MD) and Alarm.
Please highlight icon
to select the corresponding function. After completing all the setups
please click save button, system goes back to the previous menu.
At the bottom of the menu, there are color bars for your reference. Green color stands for
regular recording, yellow color stands for motion detection and red color stands for alarm
recording. The white means the motion detect record and alarm record are both valid. Once
you have set to record when the motion detect record and alarm record at the same time,
system will not record neither motion detect occurs nor the alarm record occurs.
54
Figure 4-13
4.4.1.1 Quick Setup
This function allows you to copy one channel setup to another. After setting in channel 1, you can
click paste button and turn to channel 2 and then click copy button. You can finish setting for one
channel and then click save button or you can finish all setup and then click save button to
memorize all the settings.
4.4.2 Snapshot
4.4.2.1 Schedule Snapshot
In Encode interface, click snapshot button to input snapshot mode, size, quality and
frequency.
In General interface please input upload interval.
In Schedule interface, please enable snapshot function.
Please refer to the following figure for detailed information. See Figure 4-14.
Figure 4-14
55
4.4.2.2 Activation Snapshot
Please follow the steps listed below to enable the activation snapshot function. After you
enabled this function, system can snapshot when the corresponding alarm occurred.
z In Encode interface, click snapshot button to input snapshot mode, size, quality and
frequency.
z In General interface please input upload interval.
z In Detect interface please enable snapshot function for specified channels. Or in alarm
interface please enable snapshot function for specified channels(Please note simple
lite series product does not support alarm function).
Please refer to the following figure for detailed information. See Figure 4-15.
Figure 4-15
4.4.2.3 Priority
Please note the activation snapshot has the higher priority than schedule snapshot. If you
have enabled these two types at the same time, system can activate the activation snapshot
when alarm occurs, and otherwise system just operates the schedule snapshot.
4.4.3 Image FTP
In Network interface, you can set FTP server information. Please enable FTP function and
then click save button. See Figure 4-16.
Please boot up corresponding FTP server.
Please enable schedule snapshot (Chapter 4.4.2.1) or activation snapshot (Chapter 4.4.2.2)
first, now system can upload the image file to the FTP server.
56
Please input the
corresponding information
here, if you just upload the
image FTP.
Figure 4-16
4.5 Detect
4.5.1 Go to Detect Menu
In the main menu, from Setting to Detect, you can see motion detect interface. See Figure
4-17. There are three detection types: motion detection, video loss, camera masking.
The simple lite series product does not support RS232, alarm and PTZ function.
4.5.2 Motion Detect
Detection menu is shown as below. See Figure 4-17.
z Event type: from the dropdown list you can select motion detection type.
z Channel: select the channel to activate recording function once alarm occurred. Please make
sure you have set MD record in encode interface(Main Menu->Setting->Schedule) and
schedule record in manual record interface(Main Menu->Advanced->Manual Record)
z Latch: when motion detection complete, system auto delays detecting for a specified time.
The value ranges from 10-300(Unit: second)
z Region: Click select button, the interface is shown as in Figure 4-18. Here you can set
motion detection zone. There are 396(PAL)/330(NTSC) small zones. The green zone is
current cursor position. Grey zone is the motion detection zone. Black zone is the disarmed
zone. You can click Fn button to switch between the arm mode and disarm mode. In arm
mode, you can click the direction buttons to move the green rectangle to set the motion
detection zone. After you completed the setup, please click ENTER button to exit current
setup. Do remember click save button to save current setup. If you click ESC button to exit
the region setup interface system will not save your zone setup.
z Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.
z Show message: System can pop up a message to alarm you in the local host screen if you
enabled this function.
z Alarm upload: System can upload the alarm signal to the network (including alarm centre)
if you enabled current function.
z Send email: System can send out email to alert you when alarm occurs.
z PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go to preset,
tour &pattern when there is an alarm. Click “select” button, you can see an interface is
shown as in Figure 4-19.
57
z
Period: Click set button, you can see an interface is shown as in Figure 4-20. Here you can
set for business day and non-business day. In Figure 4-20 , click set button, you can see an
interface is shown as in Figure 4-21. Here you can set your own setup for business day and
non-business day.
Anti-dither: Here you can set anti-dither time.
Alarm output: when alarm occurred, system enables peripheral alarm devices.
Tour: Here you can enable tour function when alarm occurs. It is a one-window tour. Please
go to chapter 5.3.9 Display for tour interval setup.
Buzzer: Highlight icon to enable this function. The buzzer beeps when alarm occurs.
X
X307H
z
z
z
z
Please highlight icon
to select the corresponding function. After all the setups please click
save button, system goes back to the previous menu.
Note:
In motion detection mode, you can not use copy/paste to set channel setup since the video in
each channel may not be the same.
In Figure 4-18, you can left click mouse and then drag it to set a region for motion detection.
Click Fn to switch between arm/withdraw motion detection. After setting, click enter button to exit.
Figure 4-17
Figure 4-18
58
Figure 4-19
Figure 4-20
Figure 4-21
4.5.3 Video Loss
In Figure 4-17, select video loss from the type list. You can see the interface is shown as in
Figure 4-22. This function allows you to be informed when video loss phenomenon occurred.
You can enable alarm output channel and then enable show message function.
X31H
Tips:
You can enable preset activation operation when video loss occurs.
Please refer to chapter 4.5.2 motion detection for detailed information.
59
Figure 4-22
4.5.4 Camera Masking
When someone viciously masks the lens, or the output video is in one-color due to the
environments light change, the system can alert you to guarantee video continuity. Camera
masking interface is shown as in Figure 4-23. Here you can enable alarm output or show
message in the screen.
Tips:
You can enable preset/tour/pattern activation operation when video loss occurs.
Please refer to chapter 4.5.2 motion detection for detailed information.
Note:
In Detect interface, copy/paste function is only valid for the same type, which means you can
not copy a channel setup in video loss mode to camera masking mode.
Figure 4-23
4.6 Alarm Setup and Alarm Activation
60
Please note simple lite series product does not support the alarm function.
Before operation, please make sure you have properly connected alarm devices such as light,
buzzer.
4.6.1 Go to alarm setup interface
In the main menu, from Setting to Alarm, you can see alarm setup interface. See Figure 4-24.
4.6.2 Alarm setup
Alarm interface is shown as below. See Figure 4-24.
z Alarm in: Here is for you to select channel number.
z Event type: There are two types. One is local input and the other is network input.
z Type: normal open or normal close.
z PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go to preset,
tour& pattern when there is an alarm. Click “select” button, you can see an interface is
shown as in Figure 4-25.
z Period: Click set button, you can see an interface is shown as in Figure 4-26. Here you can
set for business day and non-business day. In Figure 4-26, click set button, you can see an
interface is shown as in Figure 4-27. Here you can set your own setup for business day and
non-business day.
z Anti-dither: Here you can set anti-dither time.
z Show message: System can pop up a message to alarm you in the local host screen if you
enabled this function.
z Alarm upload: System can upload the alarm signal to the network (including alarm centre)
if you enabled current function.
z Send email: System can send out email to alert you when alarm occurs.
z Record channel: you can select proper channel to record alarm video (Multiple choices). At
the same time you need to set alarm record in schedule interface (Main Menu->Setting>Schedule) and select schedule record in manual record interface (Main Menu->Advance>Manual Record).
z Latch: Here is for you to set proper delay duration. Value ranges from 10 to 300 seconds.
System automatically delays specified seconds in turning off alarm and activated output after
external alarm cancelled.
z Tour: Here you can enable tour function when alarm occurs. It is a one-window tour: Please
go to chapter 5.3.9 Display for tour interval setup.
z Buzzer: Highlight icon to enable this function. The buzzer beeps when alarm occurs.
For snapshot operation, please refer to chapter 4.4.2.
Please highlight icon
to select the corresponding function. After setting all the setups
please click save button, system goes back to the previous menu.
61
Figure 4-24
Figure 4-25
Figure 4-26
Figure 4-27
62
4.7 Backup
DVR support USB device backup and network download. Here we introduce USB backup
first. You can refer to Chapter 7 Web Operation for network download backup operation.
4.7.1 Detect Device
Click backup button, you can see an interface is shown as in Figure 4-28.Here is for you to
view devices information.
You can view backup device name and its total space and free space. The device includes
USB burner, flash disk, SD card and portable HDD.
Figure 4-28
4.7.1 Backup
Select backup device and then set channel, file start time and end time.
Click add button, system begins search. All matched files are listed below. System
automatically calculates the capacity needed and remained. See Figure 4-29.
system only backup files with a √ before channel name. You can use Fn or cancel button to
delete √ after file serial number.
Click backup button, you can backup selected files. There is a process bar for you reference.
When the system completes backup, you can see a dialogue box prompting successful
backup.
Figure 4-29
63
Click backup button, system begins burning. At the same time, the backup button becomes
stop button. You can view the remaining time and process bar at the left bottom. See Figure
4-30.
Figure 4-30
The file name format usually is: SN_CH+channel number+time Y+M+D+H+M+S. In the file
name, the YDM format is the same as you set in general interface. (Main Menu ->Setting >General).File extension name is .dav. You can visit our website to view listed CD-ROM
brand.
Tips:
During backup process, you can click ESC to exit current interface for other operation. The
system will not terminate backup process.
Note:
When you click stop button during the burning process, the stop function becomes activated
immediately. For example, if there are ten files, when you click stop system just backup five
files, system only save the previous 5 files in the device (But you can view ten file names).
4.8 PTZ Control and Color Setup
Please note simple lite series product does not support PTZ function.
Note: All the operations here are based on PELCOD protocol. For other protocols, there
might be a little difference.
4.8.1 Cable Connection
Please follow the procedures below to go on cable connection
z Connect the dome RS485 port to DVR 485 port.
z Connect dome video output cable to DVR video input port.
z Connect power adapter to the dome.
4.8.2 PTZ Setup
Note: The camera video should be in the current screen. Before setup, please check the
following connections are right:
z PTZ and decoder connection is right. Decoder address setup is right.
z Decoder A (B) line connects with DVR A (B) line.
Boot up the DVR, input user name and password.
In the main menu, click setting, and then click Pan/Tilt Control button. The interface is shown
as in Figure 4-31. Here you can set the following items:
64
z
z
z
z
z
z
z
Channel: select the current camera channel.
Protocol: select corresponding PTZ protocol(such as PELCOD)
Address: default address is 1.
Baud rate: select corresponding baud rate. Default value is 9600.
Data bits: select corresponding data bits. Default value is 8.
Stop bits: select corresponding stop bits. Default value is 1.
Parity: there are three options: odd/even/none. Default setup is none.
Figure 4-31
After completing all the setting please click save button.
In one window display mode, right click mouse (click “Fn” Button in the front panel or click
“Fn” key in the remote control). The interface is shown as in Figure 4-32.
Figure 4-32
Click Pan/Tilt/Zoom, the interface is shown as below. See Figure 4-33.
Here you can set the following items:
z Step: value ranges fro 1 to 8.
z Zoom
z Focus
z Iris
Please click icon
and
to adjust zoom, focus and iris.
65
Figure 4-33
In Figure 4-33, please click direction arrows (See Figure 4-34) to adjust PTZ position. There are
total 8 direction arrows.
Figure 4-34
4.8.3 3D Intelligent Positioning Key
In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See Figure
4-35. Please make sure your protocol supports this function and you need to use mouse to
control.
Click this key, system goes back to the single screen mode. Drag the mouse in the screen to
adjust section size. The dragged zone supports 4X to 16X speeds. It can realize PTZ
automatically. The smaller zone you dragged, the higher the speed.
Figure 4-35
Here is a sheet for you reference.
Name
Function
function
key
Zoom
Near
Focus
Near
Iris
close
Shortcut
key
│_
W
Function
key
function
Far
Far
Open
Shortcut
Key
►│
f
4.9 Preset/ Patrol/Pattern/Scan
In Figure 4-33, please click the “set” button. The interface is shown as below. See Figure 4-36.
Here you can set the following items:
z Preset
z Tour
z Pattern
z Border
X328H
66
Figure 4-36
In Figure 4-33, click page switch button, the interface is shown as in Figure 4-37.
Here you can activate the following functions:
z Preset
z Tour
z Pattern
z Auto scan
z Auto pan
z Flip
z Reset
z Page switch
X328H
Figure 4-37
Note:
z Preset, tour and pattern all need the value to be the control parameter. You can define it as
you require.
z You need to refer to your speed dome user’s manual for Aux definition. In some cases, it
can be used for special process.
z The following setups are usually operated in the Figure 4-33, Figure 4-36 and Figure 4-37.
X328H
4.9.1Preset Setup
In Figure 4-33, please use eight direction arrows to adjust camera to the proper position.
In Figure 4-36, click preset button and input preset number. The interface is shown as in Figure
4-38
Now you can add this preset to one tour.
X
67
Figure 4-38
4.9.2 Activate Preset
In Figure 4-37, please input preset number in the No. blank, and click preset button.
4.9.3 Patrol setup (Tour Setup)
In Figure 4-36, please click patrol button. The interface is shown as in Figure 4-39.Input preset
number and add this preset to a patrol (tour). For each patrol (tour), you can input max 80
presets.
X39H
Figure 4-39
4.9.4 Activate Patrol (tour)
In Figure 4-39, input patrol (tour) number in the No. blank and click patrol button
4.9.5 Pattern Setup
In Figure 4-38 click pattern button and then click “begin” button. The interface is shown as in
Figure 4-40. Then you can go to Figure 4-33 to modify zoom, focus, and iris.
Go back to Figure 4-40 and click “end” button. You can memorize all these operations as pattern
1.
Figure 4-40
4.9.6 Activate Pattern Function
68
In Figure 4-37, input mode value in the No. blank, and click pattern button.
4.9.7 Auto Scan Setup
In Figure 4-36, click border button. The interface is shown as in Figure 4-41. Please go to Figure
4-33, use direction arrows to select camera left limit
Then please go to Figure 4-41 and click left limit button
Repeat the above procedures to set right limit.
Figure 4-41
4.9.8 Activate Auto Scan
In Figure 4-37, click “Auto Scan” button, the system begins auto scan. Correspondingly, the auto
scan button becomes Stop button. Click stop button to terminate scan operation.
4.10 Flip
In Figure 4-37, click page switch button, you can see an interface is shown as below. See Figure
4-42. Here you can set auxiliary function. The aux value has relation ship with the Aux button of
the decoder.
Click page switch button again, system goes back to Figure 4-33.
Figure 4-42
69
5 Understanding of Menu Operations and Controls
5.1 Menu Tree
The standard 1U series DVR and simple entry level series DVR menu tree is shown as below.
Backup
Information
HDD Info
BPS
Log
Version
Online Users
Setting
General
Encode
Schedule
RS232 (For standard 1U series only)
Network
Alarm
Detect
Pan/ Tilt/Zoom
Display
Default
Menu
Search
Advanced
HDD Management
Alarm Output
Abnormity
Manual Record
Account
Auto Maintain
TV Adjust
Card Overlay
Config File Backup
Shutdown
The simple lite series DVR menu tree is shown as below.
70
Backup
Information
HDD Info
BPS
Log
Version
Online Users
Setting
General
Encode
Schedule
Network
Detect
Display
Default
Menu
Search
Advanced
HDD Management
Abnormity
Manual Record
Account
Auto Maintain
TV Adjust
Card Overlay
Config File Backup
Shutdown
5.2 Main Menu
After you logged in, the system main menu is shown as below. See Figure 5-1. There are total
six icons: search, Information, setting, backup, advanced and shutdown. Move the cursor to
highlight the icon, then double click mouse to enter the sub-menu.
Figure 5-1
71
5.3 Setting
In main menu, highlight setting icon and double click mouse. System setting interface is shown
as below. See Figure 5-2.
Figure 5-2
5.3.1 General
General setting includes the following items. See Figure 5-3.
z System time: Here is for you to set system time
z Date format: There are three types: YYYYY-MM-DD: MM-DD-YYYYY or DD-MM-YYYY.
z Date separator: There are three denotations to separate date: dot, beeline and solidus.
z DST: Here you can set DST time and date. Please enable DST function and then click set
button. You can see an interface is shown as in Figure 5-4. Here you can set start time and
end time by setting corresponding week setup. In Figure 5-4, enable date button, you can
see an interface is shown as in Figure 5-5. Here you can set start time and end time by
setting corresponding date setup.
z Time format: There are two types: 24-hour mode or 12-hour mode.
z Language: System supports various languages: Chinese (simplified), Chinese (Traditional),
English, Italian, Japanese, French, Spanish (All languages listed here are optional. Slight
difference maybe found in various series.)
z HDD full: Here is for you to select working mode when hard disk is full. There are two options:
stop recording or rewrite. If current working HDD is overwritten or the current HDD is full
while the next HDD is no empty, then system stops recording, If the current HDD is full and
then next HDD is not empty, then system overwrites the previous files.
z Pack duration: Here is for you to specify record duration. The value ranges from 60 to 120
minutes. Default value is 60 minutes.
z DVR No: When you are using one remote control (not included in the accessory bag) to
control several DVRs, you can give a name to each DVR for your management.
z Video standard: There are two formats: NTSC and PAL.
z Auto logout: Here is for you to set auto logout interval once login user remains inactive for a
specified time. Value ranges from 0 to 60 minutes.
X359H
X
Note:
Since system time is very important, do not modify time casually unless there is a must!
Before your time modification, please stop record operation first!
72
After completing all the setups please click save button, system goes back to the previous menu.
Figure 5-3
Figure 5-4
Figure 5-5
5.3.2 Encode
Encode setting includes the following items. See Figure 5-6.
Please note some series do not support extra stream.
z Channel: Select the channel you want.
z Compression: System supports H.264.
z Resolution: System supports various resolutions, you can select from the dropdown list. For
this model, main stream supports D1/CIF/QCIF. Please note the resolution may vary due to
different channels. The extra stream supports QCIF only.
z Frame rate: It ranges from 1f/s to 25f/s in NTSC mode and 1f/s to 30f/s in PAL mode.
Note:
For the 8-ch series DVR, you can refer to the following information:
If the 1-channel resolution is D1and the frame rate is more than 6f/s, then the rest seven
channels (the second channel to the eights channel) resolution shall be CIF or QCIF.
73
If the 1-channel resolution is D1 and the frame rate is or less than 6f/s, then the rest seven
channels (the second channel to the eighth channel) resolution shall be D1/CIF/QCIF. Right now
in D1 resolution, the max frame rate is 6f/s.
z Bit rate type: System supports two types: CBR and VBR. In VBR mode, you can set video
quality.
z Quality: There are six levels ranging from 1 to 6. The sixth level has the highest image
quality.
z Video/audio: You can enable or disable the video/audio.
z Overlay: Click overlay button, you can see an interface is shown in Figure 5-7.
z Cover area (Privacy mask): Here is for you to set privacy mask section. You can drag you
mouse to set proper section size. In one channel video, system max supports 4 zones.
— Preview/monitor: privacy mask has two types. Preview and Monitor. Preview means the
privacy mask zone can not be viewed by user when system is in preview status. Monitor
means the privacy mask zone can not be view by the user when system is in monitor status.
— Time display: You can select system displays time or not when you playback. Please click
set button and then drag the title to the corresponding position in the screen.
— Channel display: You can select system displays channel number or not when you playback.
Please click set button and then drag the title to the corresponding position in the screen.
Please highlight icon
to select the corresponding function.
Figure 5-6
Figure 5-7
5.3.3 Schedule
Please refer to chapter 4.4 schedule.
74
5.3.4 RS232
Please note Simple entry level series product and simple lite series product does not
support RS232 function.
RS232 interface is shown as below. There are five items. See Figure 5-8.
z
Function: There are various devices for you to select. Console is for you to use the COM or
mini-end software to upgrade or debug the program. The control keyboard is for you to
control the device via the special keyboard. Transparent COM (adapter) is to connect to the
PC to transfer data directly. Protocol COM is for card overlay function. Network keyboard is
for you to use the special keyboard to control the device. PTZ matrix is to connect to the
peripheral matrix control.
z Baud rate: You can select proper baud rate.
z Data bit: You can select proper data bit. The value ranges from 5 to 8.
z Stop bit: There are three values: 1/1.5/2.
z Parity: there are three choices: none/odd/even.
System default setup is:
z Function: Console
z Baud rate:115200
z Data bit:8
z Stop bit:1
z Parity: None
After completing all the setups please click save button, system goes back to the previous menu.
Figure 5-8
5.3.5 Network
Here is for you to input network information. See Figure 5-9.
z
IP address: Here you can input IP address.
z DHCP: It is to auto search IP. When enable DHCP function, you can not modify IP/Subnet
mask /Gateway. These values are from DHCP function. If you have not enabled DHCP
function, IP/Subnet mask/Gateway display as zero. You need to disable DHCP function to
view current IP information. Besides, when PPPoE is operating, you can not modify
IP/Subnet mask /Gateway.
z TCP port: Default value is 37777.
75
UDP port: Default value is 37778.
HTTP port: Default value is 80.
Max connection: system support maximal 10 users. 0 means there is no connection limit.
Preferred DNS: DNS IP address.
Alternative DNS: DNS alternative IP address.
Transfer mode: Here you can select the priority between fluency/video qualities.
LAN download: System can process the downloaded data first if you enable this function.
The download speed is 1.5X or 2.0X of the normal speed.
After completing all the setups please click save button, system goes back to the previous menu.
z
z
z
z
z
z
z
Figure 5-9
5.3.5.1 Advanced Setup
Advanced setup interface is shown as in Figure 5-10. Please draw a circle to enable
corresponding function and then double click current item to go to setup interface.
Figure 5-10
5.3.5.2 IP Filter
IP filter interface is shown as in Figure 5-11. You can add IP in the following list. The list
supports max 64 IP addresses.
Please note after you enabled this function, only the IP listed below can access current DVR.
If you disable this function, all IP addresses can access current DVR.
76
Figure 5-11
5.3.5.3 Multiple Cast Setup
Multiple-cast setup interface is shown as in Figure 5-12.
Figure 5-12
Here you can set a multiple cast group. Please refer to the following sheet for detailed
information.
z IP multiple cast group address
-224.0.0.0-239.255.255.255
-“D” address space
z The higher four-bit of the first byte=”1110”
z Reserved local multiple cast group address
-224.0.0.0-224.0.0.255
-TTL=1 When sending out telegraph
-For example
224.0.0.1 All systems in the sub-net
224.0.0.2 All routers in the sub-net
224.0.0.4 DVMRP router
224.0.0.5 OSPF router
224.0.0.13 PIMv2 router
z Administrative scoped addressees
-239.0.0.0-239.255.255.255
77
-Private address space
z Like the single broadcast address of RFC1918
z Can not be used in Internet transmission
z Used for multiple cast broadcast in limited space.
Except the above mentioned addresses of special meaning, you can use other addresses. For
example:
Multiple cast IP: 235.8.8.36
Multiple cast PORT: 3666.
After you logged in the Web, the Web can automatically get multiple cast address and add it to
the multiple cast groups. You can enable real-time monitor function to view the view.
Please note multiple cast function applies to special series only.
5.3.5.4 PPPoE
PPPoE interface is shown as in Figure 5-13.
Input “PPPoE name” and “PPPoE password” you get from your ISP (Internet service provider).
Click save button, you need to restart to activate your configuration.
After rebooting, DVR will connect to internet automatically. The IP in the PPPoE is the DVR
dynamic value. You can access this IP to visit the unit.
Figure 5-13
5.3.5.5 NTP Setup
You need to install SNTP server (Such as Absolute Time Server) in your PC first. In Windows XP
OS, you can use command “net start w32time” to boot up NTP service.
NTP setup interface is shown as in Figure 5-14.
z Host IP: Input your PC address.
z Port: This series DVR supports TCP transmission only. Port default value is 123.
z Update interval: minimum value is 1. Max value is 65535. (Unit: minute)
z Time zone: select your corresponding time zone here.
Here is a sheet for your time zone setup.
City /Region Name
Time Zone
London
GMT+0
Berlin
GMT+1
Cairo
GMT+2
Moscow
GMT+3
New Deli
GMT+5
Bangkok
GMT+7
Beijing (Hong Kong)
GMT+8
Tokyo
GMT+9
Sydney
GMT+10
Hawaii
GMT-10
78
Alaska
Pacific Time(P.T)
American Mountain Time(M.T)
American Central Time(C.T)
American Eastern Time(E.T)
Atlantic Time
Brazil
Middle Atlantic Time
GMT-9
GMT-8
GMT-7
GMT-6
GMT-5
GMT-4
GMT-3
GMT-2
Figure 5-14
5.3.5.6 DDNS Setup
DDNS setup interface is shown as in Figure 5-15.
You need a PC of fixed IP in the internet and there is the DDNS software running in this PC. In
other words, this PC is a DNS (domain name server).
In network DDNS, please select DDNS type and highlight enable item. Them please input your
PPPoE name you get from you IPS and server IP (PC with DDNS ) . Click save button and then
reboot system.
Click save button, system prompts for rebooting to get all setup activated.
After rebooting, open IE and input as below:
http://(DDNS server IP)/(virtual directory name)/webtest.htm
e.g.: http://10.6.2.85/DVR _DDNS/webtest.htm.)
Now you can open DDNSServer web search page.
Figure 5-15
Please note NNDS type includes: CN99 DDNS、NO-IP DDNS、Private DDNS、Dyndns DDNS
and sysdns DDNS. All the DDNS can be valid at the same time, you can select as you
requirement.
Private DDNS function shall work with special DDNS server and special Professional
Surveillance Software (PSS).
79
5.3.5.7 FTP
You need to download or buy FTP service tool (such as Ser-U FTP SERVER) to establish FTP
service.
Please install Ser-U FTP SERVER first. From “start” -> “program” -> Serv-U FTP Server -> ServU Administator. Now you can set user password and FTP folder. Please note you need to grant
write right to FTP upload user. See Figure 5-16.
Figure 5-16
You can use a PC or FTP login tool to test setup is right or not.
For example, you can login user ZHY to FTP://10.10.7.7 and then test it can modify or delete
folder or not. See Figure 5-17.
H140TU
UTH
Figure 5-17
System also supports upload multiple DVRs to one FTP server. You can create multiple folders
under this FTP.
In Figure 5-9, select FTP and then double click mouse. You can see the following interface. See
Figure 5-18.
80
Figure 5-18
Please highlight the icon
in front of Enable to activate FTP function.
Here you can input FTP server address, port and remote directory. When remote directory is null,
system automatically create folders according to the IP, time and channel.
User name and password is the account information for you to login the FTP.
File length is upload file length. When setup is larger than the actual file length, system will
upload the whole file. When setup here is smaller than the actual file length, system only uploads
the set length and auto ignore the left section. When interval value is 0, system uploads all
corresponding files.
After completed channel and weekday setup, you can set two periods for one each channel.
5.3.5.8 Alarm Centre
This interface is reserved for you to develop.
5.3.6 Alarm
Please refer to chapter 4.6 Alarm Setup and Activation.
5.3.7 Detect
Please refer to chapter 4.5 Detect.
5.3.8 Pan/Tilt/Zoom
The pan/tilt/zoom setup includes the following items. Please select channel first. See Figure 5-19.
z
Protocol: Select corresponding PTZ protocol such as PELCOD.
z Address: input corresponding PTZ address.
z Baud rate: Select baud rate.
z Data bit: Select data bit.
z Stop bit: Select stop bit.
z Parity: There are three choices: none/odd/even.
After completed all the setups please click save button, system goes back to the previous menu.
For detailed setup, please refer to chapter 4.9 preset/patrol/pattern/scan.
81
Figure 5-19
5.3.9 Display
Display setup interface is shown as below. See Figure 5-20.
z Transparency: Here is for you to adjust transparency. The value ranges from 128 to 255.
z Channel name: Here is for you to modify channel name. System max support 25-digit (The
value may vary due to different series). Please note all your modification here only applies to
DVR local end. You need to open web or client end to refresh channel name.
z Time display: You can select to display time or not when system is playback.
z Channel display: You can select to channel name or not when system is playback.
z Overlay information: System displays some information in the screen for your reference.
z Resolution: There are four options: 1280×1024(default),1280×720,1024×768,800×600.
Please note system needs to reboot to activate current setup.
z Enable tour: Activate tour function.
z Interval: Input proper interval value here. The value ranges from 5-120 seconds. In tour
process, you can use mouse or click Shift to turn on window switch function.
z
z
Stands for
stands for closing switch function.
opening switch function,
Motion tour type: System support 1/8 window tour.
Alarm tour type: System support 1/8window tour.
Please highlight icon
to select the corresponding function.
After completing all the setups please click save button, system goes back to the previous menu.
82
Figure 5-20
In Figure 5-20, click modify button after channel. You can see an interface is shown as in Figure
5-21. Please note all your modification here applies to local end only. You need to refresh web or
client-end to get the latest channel name. System max support 25-digital character.
X
Figure 5-21
In tour mode, you can see the following interface. On the right corner, right click mouse or click
shift button, you can control the tour. There are two icons:
and
stands for enabling window switch
stands for enabling window function. See Figure 5-22.
Figure 5-22
83
5.3.10 Default
Click default icon, system pops up a dialogue box. You can highlight
to restore default factory
setup. See Figure 5-23.
z
Select all
z General
z Encode
z Schedule
z RS232
z Network
z Alarm
z Detect
z Pan/tilt/zoom
z Display
z Channel name
Please highlight icon
to select the corresponding function.
After all the setups please click save button, system goes back to the previous menu.
Warning!
System menu color, language, time display mode, video format, IP address, user account will not
maintain previous setup after default operation!
Figure 5-23
5.4 Search
Please refer to chapter 4.3 Search.
5.5 Advanced
Double click advanced icon in the main window, the interface is shown as below. See Figure
5-24. There are total nine function keys: HDD management, alarm output, abnormity, manual
record, account, auto maintenance, TV adjust, card overlay and config file backup.
84
Figure 5-24
5.5.1 HDD Management
Here is for you to view and implement hard disk management. See Figure 5-25.
You can see current HDD type, status, capacity and record time. When HDD is working properly,
system is shown as O. When HDD error occurred, system is shown as X.
You can select HDD mode from the dropdown list such as read-only or you can erase all data in
the HDD.
Please note system needs to reboot to get all the modification activated.
Figure 5-25
Click alarm set button, the interface is shown as below. See Figure 5-26. (This interface is just
like the abnormity setup). Please refer to chapter 5.5.2 for detailed information.
Please highlight icon
to select the corresponding function.
85
Figure 5-26
5.5.2 Abnormity
Abnormity interface is shown as in Figure 5-27.
z Event type: There are several options for you such as disk error, no disk, disconnection,
IP conflict and etc.
z Alarm output: Please select alarm activation output port (multiple choices).
z Latch: Here you can set corresponding delaying time. The value ranges from 10s-300s.
System automatically delays specified seconds in turning off alarm and activated output
after external alarm cancelled.
z Show message: system can pop up the message in the local screen to alert you when
alarm occurs.
z Alarm upload: System can upload the alarm signal to the network (including alarm centre)
if you enabled current function.
z Send email: System can send out email to alert you when alarm occurs.
z Buzzer: System can activate the buzzer to beep when alarm occurs.
Figure 5-27
5.5.3 Alarm Output
Here is for you to set proper alarm output.
86
Please highlight icon
to select the corresponding alarm output.
After all the setups please click OK button, system goes back to the previous menu. See Figure
5-28.
Figure 5-28
5.5.4 Manual Record
Please refer to chapter 4.2.2 manual record.
5.5.5 Account
Here is for you to implement account management. See Figure 5-29. Here you can:
z Add new user
z Modify user
z Add group
z Modify group
z Modify password.
For account management please note:
z System account adopts two-level management: group and user. No limit to group or user
amount.
z For group or user management, there are two levels: admin and user.
z The user name and group name can consist of eight bytes. One name can only be used
once. There are four default users: admin/888888/666666 and hidden user “default”. Except
user 6666, other users have administrator right.
z Hidden user “default” is for system interior use only and can not be deleted. When there is
no login user, hidden user “default” automatically login. You can set some rights such as
monitor for this user so that you can view some channel view without login.
z One user should belong to one group. User right can not exceed group right.
z About reusable function: this function allows multiple users use the same account to login.
After all the setups please click save button, system goes back to the previous menu.
87
Figure 5-29
5.5.6 Auto Maintain
Here you can set auto-reboot time and auto-delete old files setup. See Figure 5-30.
You can select proper setup from dropdown list.
After all the setups please click save button, system goes back to the previous menu.
Figure 5-30
5.5.7 TV Adjust
Here is for you to adjust TV output setup. See Figure 5-31.
Please drag slide bar to adjust each item.
After all the setups please click OK button, system goes back to the previous menu.
Figure 5-31
88
5.5.8 Card Overlay
The card overlay function is for financial areas. It includes Sniffer, information analysis and title
overlay function. The Sniffer mode includes COM and network.
5.5.8.1 COM Type
The COM interface is shown as below. See Figure 5-32.
z
Protocol: Please select from the dropdown list.
z Setting: Click COM setting button, the interface is shown as in RS232 interface. Please refer
to Chapter 5.3.4 RS232.
z Overlay channel: Please select the channel you want to overlay the card number.
z Overlay mode: There are two options: preview and encode. Preview means overlay the card
number in the local monitor video. Encode means overlay the card number in the record file.
z Overlay Position: Here you can select the proper overlay position from the dropdown list.
Figure 5-32
5.5.8.2 Network Type
The network type interface is shown as below. See Figure 5-33.
Here we take the ATM/POS protocol to continue.
There are two types: with or without the protocol according to client’s requirements.
With the protocol
For ATM/POS with the protocol, you just need to set the source IP, destination IP (sometimes
you need to input corresponding port number).
Figure 5-33
89
Without the protocol
For the ATM/POS without the protocol, the interface is shown as in Figure 5-34.
Source IP refers to host IP address that sends out information (usually it is the device host.)
Destination IP refers to other systems that receive information.
Usually you do not need to set source port and target port.
There are total four groups IP. The record channel applies to one group (optional) only.
Six frame ID groups verification can guarantee information validity and legal.
Figure 5-34
Click Data button you can see an interface is shown as in Figure 5-35.
Here you can set offset value, length, title according to your communication protocol and data
package. .
Figure 5-35
5.5.9 Config File Backup
The configuration file backup interface is shown as below. See Figure 5-36.
This function allows you to copy current system configuration to other devices.
90
Figure 5-36
5.6 Information
Here is for you to view system information. There are total five items: HDD (hard disk
information), BPS (data stream statistics), Log and version, and online user. See Figure 5-37.
Figure 5-37
5.6.1 HDD Information
Here is to list hard disk type, total space, free space, video start time and status. See Figure 5-38.
○ means current HDD is normal. X means there is error. - means there is no HDD.
If disk is damaged, system shows as “?”. Please remove the broken hard disk before you add a
new one.
Once there is a hard disk confliction, please check hard disk time and system time is the same or
not. Please go to setting then general to modify system time. At last, reboot the system to solve
this problem.
After system booted up, if there is any confliction, system goes to HDD information interface
directly. Please note, system does not ask you to deal with it forcedly.
91
When HDD confliction occurs, you can check system time and HDD time are identical or not. If
they are not identical, please go to General (Chapter 5.3.1) to adjust system time or go to HDD
Management (Chapter 5.5.1) to format HDD and then reboot the DVR.
Figure 5-38
Tips:
Please click Fn button or left click mouse to view HDD record time and HDD type and time.
5.6.2 BPS
Here is for you to view current video data stream (KB/s) and occupied hard disk storage (MB/h).
See Figure 5-39.
Figure 5-39
5.6.3 Log
Here is for you to view system log file. System lists the following information. See Figure 5-40.
Log types include system operation, configuration operation, data management, alarm event,
record operation, log clear and etc.
Pleased select start time and end time, then click search button. You can view the log files.
Please page up/down button to view if there are more than ten files.
92
Figure 5-40
5.6.4 Version
Here is for you to view some version information. See Figure 5-41.
z
Channel
z Alarm in
z Alarm out
z System version:
z Build Date
Figure 5-41
5.6.5 Online Users
Here is for you manage online users. See Figure 5-42
You can disconnect one user or block one user if you have proper system right. Max
disconnection setup is 65535 seconds.
93
Figure 5-42
5.7 Shutdown
Double click shutdown button, system pops up a dialogue box for you to select. See Figure 5-43.
z Logout menu user: log out menu. You need to input password when you login the next time.
z Restart application: reboot DVR.
z Shutdown: system shuts down and turns off power.
z
Restart system: system begins rebooting.
z Switch user: you can use another account to log in.
Figure 5-43
94
6 About Auxiliary Menu
6.1
Go to Pan/Tilt/Zoom Menu
Please note simple lite series product does not support PTZ function.
In the one-window surveillance mode, right click mouse (click “fn” Button in the front panel or
click AUX key in the remote control). The interface is shown as below: See Figure 6-1.
X397H
X
Figure 6-1
Click Pan/Tilt/Zoom, the interface is shown as in Figure 6-2.
Here you can set the following items:
z Zoom
z Focus
z Iris
Please click icon
and
to adjust zoom, focus and Iris.
X398H
X
Figure 6-2
In Figure 6-2, please click direction arrows (See Figure 6-3 ) to adjust PTZ position. There are
totally eight direction arrows. (Please note there are only four direction arrows in DVR front
panel.)
X39H
X
X40H
X
Figure 6-3
6.1.1 3D Intelligent Positioning Key
95
In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See Figure
6-4 . Please make sure your protocol supports this function and you need to use mouse to
control.
Click this button, system goes back to the single screen mode. Drag the mouse in the screen to
adjust section size.
X401H
X
Figure 6-4
Here is a sheet for you reference.
Name
Function
function
key
Near
Zoom
Near
Focus
Iris
close
Shortcut
key
Function
key
│_
W
function
Shortcut
key
►│
f
Far
Far
Open
6.2 Preset /Patrol / Pattern /Border Function
In Figure 6-2 click the set button. The interface is shown as below:
Here you can set the following items:
z Preset
z Patrol
z Pattern
z Border
X402H
X
Figure 6-5
In Figure 6-2, click page switch button, you can see an interface as in Figure 6-6.
Here you can activate the following functions:
z Preset
z Tour(Patrol)
z Pattern
z Auto scan
z Auto pan
z Flip
z Page Switch
X403H
X
X40H
X
96
Figure 6-6
6.2.1 Preset Setup
Note: The following setups are usually operated in the Figure 6-2, Figure 6-5 and Figure 6-6.
In Figure 6-2, use eight direction arrows to adjust camera to the proper position.
In Figure 6-5, click preset button and input preset number. The interface is shown as in Figure
6-7.
Add this preset to one patrol number
X405H
X408H
X
X406H
X
X407H
X
X
X409H
X
X410H
X
Figure 6-7
6.2.2 Activate Preset
In Figure 6-6 please input preset number in the No. blank, and click preset button.
X41H
X
6.2.3 Patrol Setup
In Figure 6-5, click patrol button. The interface is shown as in Figure 6-8.
Input preset number and then add this preset to one patrol.
X412H
X
X413H
X
Figure 6-8
6.2.4 Activate Patrol
In Figure 6-6, input patrol number in the No. blank and click patrol button
X41H
X
6.2.5 Pattern Setup
In Figure 6-5, click pattern button and then click begin button. The interface shows like Figure 6-9.
Please go to Figure 6-2 to modify zoom, focus, and iris. Go back to Figure 6-9 and click end
button.
X415H
X
X417H
X416H
X
X418H
X
X
97
You can memorize all these setups as pattern 1.
Figure 6-9
6.2.6 Activate Pattern Function
In Figure 6-6 input mode value in the No. blank, and click pattern button.
X419H
X
6.2.7 Border Setup
In Figure 6-5, click border button. The interface is shown as in Figure 6-10.
Please go to Figure 6-2, use direction arrows to select camera left limit, and then please go to
Figure 6-10 and click left limit button
Repeat the above procedures to set right limit.
X420H
X
X421H
X42H
X423H
X
X
X
Figure 6-10
6.2.8 Activate Border Function
In Figure 6-6, click auto scan button, the system begins auto scan. Correspondingly, the auto
scan button changes to stop button.
Click stop button to terminate scan operation.
X42H
X
6.2.9
Flip
In Figure 6-6, click page switch button, you can see an interface is shown as below. See Figure
6-11. Here you can set auxiliary function.
Click page switch button again, system goes back to Figure 6-2.
X425H
X
X426H
X
X427H
X
98
Figure 6-11
99
7 WEB OPERATION
Important
z Slight difference may be found in the interface. All the interfaces listed below are based on
the standard 1U series product.
z The simple entry level series product does not support RS232 function.
z The 8-channel simple entry level series product does not support schedule snapshot
function and etc. Please note for this series product, when you logged in the Web to operate
real-time monitor/network playback/network download, the local-end 8-channel playback is
disabled, and vice versa.
z The simple lite series product does not support RS232, alarm and PTZ function.
7.1 Network Connection
Before web operation, please check the following items:
z Network connection is right
z DVR and PC network setup is right. Please refer to network setup(main menu->setting>network)
z Use order ping ***.***.***.***(* DVR IP address) to check connection is OK or not. Usually
the return TTL value should be less than 255.
z Open the IE and then input DVR IP address.
z System can automatically download latest web control and the new version can overwrite
the previous one.
z If you want to un-install the web control, please run uninstall webrec2.0.bat. Or you can go to
C:\Program Files\webrec to remove single folder. Please note, before you un-install, please
close all web pages, otherwise the un-installation might result in error.
7.2 Login
Open IE and input DVR address in the address column. For example, if your DVR IP is
10.10.3.16, then please input http:// 10.10.3.16 in IE address column. See Figure 7-1.
X428H
X
Input your IP
address here.
Figure 7-1
100
System pops up warning information to ask you whether install webrec.cab control or not. Please
click yes button.
If you can’t download the ActiveX file, please modify your settings as follows. See Figure 7-2.
X429H
X
Figure 7-2
After installation, the interface is shown as below. See Figure 7-3.
Please input your user name and password.
Default factory name is admin and password is admin.
X430H
X
Note: For security reasons, please modify your password after you first login.
Figure 7-3
101
After you logged in, you can see the main window. See Figure 7-6.
This main window can be divided into the following sections.
z Section 1: there are five function buttons: configuration (chapter 7.3), search (chapter 7.4),
alarm (chapter 7.5), about (chapter 7.6), log out (chapter 7.7).
z Section 2: there are channel number and three function buttons: start dialog and local play,
refresh.
z Section3: there are PTZ (chapter 7.2.2), color (chapter 7.2.3) button and you can also select
picture path and record path.
z Section 4:real-time monitor window. Please note current preview window is circled by a
green rectangle zone.
z Section 5: Here you can view window switch button. You can also select video priority
between fluency or real-time.
— System monitor window switch supports full screen/1-window/4-window/6-window/8window/9-window/13-window/16-window/20-window/25-window/36-window. See Figure
7-4.
X431H
X
X432H
X
Figure 7-4
—
Preview window switch. System support 1/4/8/9/16-window real-time preview. Please you
need to have the proper rights to implement preview operation. You can not preview if you
have no right to preview the either channel. See Figure 7-5. Please note this series device
does not support this function.
Figure 7-5
Section1
Section 3
Section 4
Section 2
Section 5
Figure 7-6
102
7.2.1 Real-time Monitor
In section 2, left click the channel name you want to view, you can see the corresponding video
in current window.
On the top left corner, you can view device IP, channel number, network monitor bit stream.
1
2
3
Figure 7-7
On the top right corer, there are six unction buttons. See Figure 7-8.
X43H
1 2
3 4
5
X
6
Figure 7-8
1: Digital zoom: Click this button and then left drag the mouse in the zone to zoom in. right
click mouse system restores original status.
z 2: Change show mode: resize or switch to full screen mode.
z 3: Local record. When you click local record button, the system begins recording and this
button becomes highlighted. You can go to system folder RecordDownload to view the
recorded file.
z 4: Capture picture. You can snapshoot important video. All images are memorized in system
client folder \download\picture (default).
z 5: Audio :Turn on or off audio.(It has no relationship with system audio setup )
z 6: Close video.
Please refer to Figure 7-9 for main stream and extra stream switch information.
z
X435H
X
Figure 7-9
103
Open All
You can click it to open all channels.
Refresh
You can use button to refresh camera list.
Start Dialogue
You can click this button to enable audio talk. Click 【▼】 to select bidirectional talk mode.
There are two options: DEFAULT/G711a.
Please note, the audio input port from the device to the client-end is using the first channel audio
input port. During the bidirectional talk process, system will not encode the audio data from the 1channel.
X436H
Local Play
The Web can playback the saved (Extension name is dav) files in the PC-end.
Click local play button, system pops up the following interface for you to select local play file. See
Figure 7-10.
X
Figure 7-10
7.2.2 PTZ
The simple lite series product does not PTZ function.
Before PTZ operation, please make sure you have properly set PTZ protocol. (Please refer to
chapter 7.3.2 Setting-> Pan/Tilt/Zoom).
Click PTZ button, the interface is shown as in Figure 7-11.
X437H
X
104
3D Intelligent Positioning
Key
You can click this icon to
display or hide the PTZ
control platform.
Figure 7-11
7.2.2.1 Direction key and 3D positioning key
In Figure 7-10, there are eight direction keys.
In the middle of the eight direction keys, there is a 3D intelligent positioning key.
Click 3D intelligent positioning key, system goes back to the single screen mode. Drag the
mouse in the screen to adjust section size. It can realize PTZ automatically.
7.2.2.2 Speed
System supports eight-level speed. You can select from the dropdown list. Speed 2 is faster than
speed 1.
7.2.2.3 Zoom/Focus/Iris
Here is a sheet for you reference.
Name
Function
key
Zoom
Function
Function
key
Function
Near
Far
Focus
Near
Far
Iris
close
Open
In Figure 7-11, click PTZ setup button you can see the following interface. See Figure 7-12.
X438H
X
105
Figure 7-12
7.2.2.4 Auto Scan
In Figure 7-12, move the camera to you desired location and then click left limit button.
X439H
X
Then move the camera again and then click right limit button to set a right limit.
7.2.2.5 Pattern
In Figure 7-12, you can input pattern value and then click start record button to begin PTZ
movement. Please go back to Figure 7-11 to implement camera operation. Then you can click
stop record button. Now you have set one pattern.
X40H
X
7.2.2.6 Preset
In Figure 7-12, move the camera to your desired location and then input preset value. Click add
button, you have set one preset.
X41H
X
7.2.2.7 Auto tour
In Figure 7-12, input auto tour value and preset value. Click add button, you have added one
preset in the tour.
Repeat the above procedures you can add more presets in one tour.
X42H
X
7.2.2.8 Assistant
You can select the assistant item from the dropdown list. See Figure 7-13.
X43H
X
7.2.2.9 Matrix
This series product supports matrix extension function. You can control the video input and
output switch
7.2.2.10 Light and wiper
If your PTZ protocol supports the light and wiper control function. You can enable/disable the
light or the wiper.
106
Figure 7-13
7.2.3 Color
Click color button in section 3, the interface is shown as Figure 7-14.
Here you can select one channel and then adjust its brightness, contrast, hue and saturation.
(Current channel border becomes green).
Or you can click default button to use system default setup.
X4H
X
Figure 7-14
7.2.4 Picture Path and Record Path
Click more button in Figure 7-14, you can see an interface is shown as in Figure 7-15.
X45H
X
X46H
X
Figure 7-15
107
Click picture path button, you can see an interface is shown as in Figure 7-16.
Please click choose button to modify path.
X47H
X
Figure 7-16
Click record path button, you can see an interface is shown as in Figure 7-17.
Please click choose button to modify path.
X48H
X
Figure 7-17
Click reboot button, system pops up the following dialogue box. See Figure 7-18,
Please click OK to reboot.
Figure 7-18
If there is local use logged in the system menu, or the Web logged in user has no right to reboot
the device system pops up a dialogue box to alert you.
7.3 Configure
7.3.1 System Information
7.3.1.1 Version Information
Here you can view device hardware feature and software version information. See Figure 7-19.
X49H
X
108
Figure 7-19
7.3.1.2 HDD information
Here you can view local storage status and network status including, free capacity and total
capacity. See Figure 7-20.
X450H
X
Figure 7-20
7.3.1.3 Log
Here you can view system log. See Figure 7-21.
X451H
X
109
Figure 7-21
Click backup button, the interface is shown as in Figure 7-22.
X452H
X
Figure 7-22
Please refer to the following sheet for log parameter information.
Parameter
Function
Type
Log types include: system operation, configuration operation, data
management, alarm event, record operation, user management, log
clear and file operation.
You can select log type from the drop down list and then click search
button to view the list.
Search
Clear
You can click this button to delete all displayed log files. Please note
system does not support clear by type.
Backup
You can click this button to backup log files to current PC.
7.3.2 System Configuration
Please click save button to save your current setup.
7.3.2.1 General Setup
Here you can set system time, record length, video format and etc. See Figure 7-23
X453H
X.
110
Figure 7-23
Figure 7-24
Figure 7-25
Please refer to the following sheet for detailed information.
Parameter
Function
System
Time
Here is for you to modify system time. Please click Save button after
your completed modification
Sync PC
You can click this button to save the system time as your PC current
time.
111
Data
Format
Here you can select data format from the dropdown list.
Data
Separator
Please select separator such as – or /.
Time
Format
There are two options: 24-H and 12-H.
DST
Here you can set day night save time begin time and end time. See
Figure 7-24 and Figure 7-25.
Language
You can select the language from the dropdown list. Device needs to
reboot to get the modification activated.
HDD Full
There are two options: stop recording or overwrite the previous files
when HDD is full.
When current working HDD is overwriting or it is full now, system
stops record.
If current working HDD is full now, system goes to overwrite the
previous file.
Here you can select file size. The value ranges from 1 to 120.Default
setup is 60 minutes.
Pack
Duration
Device No
When you are using one remote control (not included in the
accessory bag) to manage multiple devices, you can give a serial
numbers to the device.
Video
Standard
There are two options: PAL/NTSC.
Please note, for the Web user, this information is for reference only.
You can not modify.
7.3.2.2 Encode
Encode interface is shown as in Figure 7-26.
X45H
X
112
Figure 7-26
Figure 7-27
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Here is for you to select a monitor channel.
Channel Name
Here is to display current channel name. You can modify it.
Compression
H.264
113
Parameter
Function
Main Stream
It includes main stream, motion stream and alarm stream. You can
select different encode frame rates form different recorded events.
System supports active control frame function (ACF). It allows you to
record in different frame rates.
For example, you can use high frame rate to record important events,
record scheduled event in lower frame rate and it allows you to set
different frame rates for motion detection record and alarm record.
Extra Stream
Select extra stream if you enabled the extension stream to monitor.
Audio/Video
For the main stream, recorded file only contains video by default. You
need to draw a circle here to enable audio function.
For extra stream, you need to draw a circle to select the video first and
then select the audio if necessary.
Resolution
For 16ch series:
Main stream resolution supports D1/CIF/QCIF.
Extra stream of channel 1 to channel 16 support QCIF only.
Frame Rate
Bit Rate Type
Quality
Bit Rate
PAL:1~25f/s;NTSC:1~30f/s
For the 8-ch series DVR, you can refer to the following information:
If the 1-channel resolution is D1and the frame rate is more than 6f/s,
then the rest seven channels (the second channel to the eights
channel) resolution shall be CIF or QCIF.
If the 1-channel resolution is D1 and the frame rate is or less than 6f/
then the rest seven channels (the second channel to the eights
channel) resolution shall be D1/CIF/QCIF. Right now in D1 resolution
the max frame rate is 6f/s.
There are two options: VBR and CBR.
Please note, you can set video quality in VBR mode only.
The value ranges from 1 to 6. The level 6 is the best video quality.
z
In CBR, the bit rate here is the max value. In dynamic video, system
needs to low frame rate or video quality to guarantee the value.
z
The value is null in VBR mode.
z
Please refer to recommend bit rate for the detailed information.
Recommended
Bit
Recommended bit rate value according to the resolution and frame
rate you have set.
Color Setting
Here you can set video brightness, contrast ness, hue, saturation and
gain.
The value ranges from 0 to 100.Default value is 50. See Figure 7-27.
Please note, some series devices do not support OSD transparent
setup function.
Cover area
(privacy mask)
z
Here you can privacy mask the specified video in the monitor video.
z
One channel max supports 4 privacy mask zones.
z
The privacy mask includes two options: Never/monitor. Never: It
means do not enable privacy mask function. Monitor: the privacy
mask zone can not be viewed in monitor mode.
114
Parameter
Function
Time Title
z
You can enable this function so that system overlays time
information in video window.
z
OSD transparent value ranges from 0 to 255. 0 means complete
transparent.
z
You can use the mouse to drag the time tile position.
z
You can enable this function so that system overlays channel
information in video window.
z
OSD transparent value ranges from 0 to 255. 0 means complete
transparent.
z
You can use the mouse to drag the channel tile position.
Channel Title
Copy
It is a shortcut menu button. You can copy current channel setup to
one or more channels. The interface is shown as in Figure 7-28.
X45H
X
Save
You can click save button after you complete setup for one channel, or
you can complete the whole setups and then click save button.
Refresh
Click this button to get device latest configuration information.
Click copy interface, the interface is shown as in Figure 7-28.
If you have completed the setup for channel 1, you can click 3 to copy current setup to channel 3.
Or you can click 2, 3, and 4 to copy current setup to channel 2, channel 3 and channel 4.
X456H
X
Figure 7-28
7.3.2.3 Schedule
X457H
Here you can set different periods for various days. There are max six periods in one day. See
Figure 7-29
X
115
Figure 7-29
Figure 7-30
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Please select a channel first.
Pre-record
Please input pre-record value here.
System can record the three to five seconds video before activating
the record operation into the file. (Depends on data size).
116
Parameter
Function
Setup
z
In Figure 7-29, click set button, you can go to the corresponding
setup interface.
z
Please set schedule period and then select corresponding record
or snapshot type: schedule/snapshot, motion detection/snapshot,
and alarm/snapshot.
z
Please select date (Current setup applies to current day by default.
You can draw a circle before the week to apply the setup to the
whole week.)
z
After complete setup, please go back to Figure 7-29 and then click
save to save current time period setup.
Copy
X458H
X
X459H
X
It is a shortcut menu button. You can copy current channel setup to
one or more (all) channels. The interface is shown as in Figure
7-28.
X460H
X
Save
You can click save button after you complete setup for one channel,
or you can complete the whole setups and then click save button.
Refresh
Click this button to get device latest configuration information.
7.3.2.4 RS232
The simple entry level series product and the simple lite series product do not support
RS232 function.
The RS232 interface is shown as in Figure 7-31.
X461H
X
Figure 7-31
Please refer to the following sheet for detailed information.
Parameter
Function
RS232
Select the corresponding COM control protocol.
Data Bit
The value ranges from 5 to 8.
117
Parameter
Function
Stop Bit
There are three options: 1/2.
Baud Bit
You can select corresponding baud bit here.
Parity
There are five options: none/odd/even/space/mark.
System default setup is:
z Function: Console.
z Data bit: 8
z Stop bit: 1
z Baud bit: 115200
z Parity: None.
7.3.2.5 Network
Network interface is shown as in Figure 7-32.
X462H
X
Figure 7-32
Please refer to the following sheet for detailed information.
Parameter
Function
Ethernet
Please select the network card first.
DHCP
Dynamically get IP address. You can get the device IP from
the DHCP server if you enabled this function.
TCP Port
Default value is 37777.
HTTP Port
Default value is 80.
UDP Port
Default value is 37778.
Max Connection
Network user max amount. The value ranges from 0 to 10.
O means there is no user can access current device.
118
Parameter
Remote
Host
Function
Multiple
cast
group
z
Set MULCAST address and port.
z
Enable MULCAST function.
PPPOE
z
Input the PPPoE user name and password you get from the
IPS (internet service provider) and enable PPPoE function.
Please save current setup and then reboot the device to
get the setup activated.
z
Device connects to the internet via PPPoE after reboot.
You can get the IP address in the WAN from the IP address
column.
z
Please note if you want to reboot the device please make
sure you have proper reboot right and there is no login user
in current device.
Email
The email interface is shown as in Figure 7-33.
X463H
X
Figure 7-33
Please refer to the following sheet for detailed information.
Parameter
Function
SMTP Server
Input server address and then enable this function.
Port
Default value is 25. You can modify it if necessary.
User Name
The sender email account user name.
Password
The sender email account password.
Sender
Sender email address.
Subject
Input email subject here.
Address
Input receiver email address here. Max input three addresses.
DDNS
119
The DDNS interface is shown as in Figure 7-34.
Please make sure your DVR support this function.
X46H
X
Figure 7-34
Please refer to the following sheet for detailed information.
Parameter
Function
Server Type
You can select DDNS protocol from the dropdown list and then
enable DDNS function. The private DDNS protocol means you
use your self-defined private protocol to realize DDNS function.
Server IP
DDNS server IP address
Server Port
DDNS server port.
Domain Name
Your self-defined domain name.
User
The user name you input to log in the server.
Password
The password you input to log in the server.
Interval
z
Device sends out alive signal to the server regularly.
z
You can set interval value between the device and DDNS
server here.
NAS
NAS interface is shown as in Figure 7-35.
Please make sure your DVR support this function.
X465H
X
120
Figure 7-35
Please refer to the following sheet for detailed information.
Parameter
Function
NAS enable
Please select network storage protocol and then enable
NAS function.
Server IP
Input remote storage server IP address.
Port
Input Remote storage server port number.
User Name
Log in user account.
File length
The file length you upload to the FTP.
When setup is larger than the actual file length, system
will upload the whole file. When setup here is smaller
than the actual file length, system only uploads the set
length and auto ignore the left section. When interval
value is 0, system uploads all corresponding files.
Password
The password you need to log in the server.
Remote Path
Remote storage file path.
Save
You can click save button after you complete setup for
one channel, or you can complete the whole setups and
then click save button.
Refresh
Click this button to get device latest configuration
information.
NTP
The NTP interface is shown as in Figure 7-36.
Here you can realize network time synchronization. Please enable current function and then
input server IP, port number, time zone and update interval. Please note the SNTP supports TCP
X46H
X
121
transmission only and its port shall be 123.The update interval ranges from 1 to 65535. Default
value is 10 minutes.
Figure 7-36
You can refer to the following sheet for time zone information.
City /Region Name
Time Zone
London
GMT+0
Berlin
GMT+1
Cairo
GMT+2
Moscow
GMT+3
New Deli
GMT+5
Bangkok
GMT+7
Beijing (Hong Kong)
GMT+8
Tokyo
GMT+9
Sydney
GMT+10
Hawaii
GMT-10
Alaska
GMT-9
Pacific Time(P.T)
GMT-8
American Mountain Time(M.T)
GMT-7
American Central Time(C.T)
GMT-6
American Eastern Time(E.T)
GMT-5
Atlantic Time
GMT-4
Brazil
GMT-3
Middle Atlantic Time
GMT-2
Alarm Centre
Alarm centre interface is shown as below.
This interface is for you to develop. The alarm signal can be uploaded to the alarm centre when
there is local alarm.
Please set the corresponding parameters such as server IP, port and etc.
The system can send out the data as the protocol defined to the client-end.
122
Figure 7-37
7.3.2.6 Alarm
The simple lite series product does not support alarm function.
Alarm setup interface is shown as in Figure 7-38.
Please make sure you have connected the corresponding alarm output device such as the light,
buzzer and etc.
X467H
X
Figure 7-38
123
Figure 7-39
Please refer to the following sheet for detailed information.
Parameter Function
Event
It includes local alarm/network alarm.
Type
Local alarm: Device detects alarm from input port.
Network: Device detects alarm from network.
Alarm in
Select corresponding alarm channel.
Enable
You need to draw a circle here so that system can detect the alarm
signal.
Type
There are two options: normal open and normal close. NO becomes
activated in low voltage, NC becomes activated in high voltage.
Period
Anti-dither
Normal
Out
Alarm
Latch
Alarm
upload
Record
Channel
Record
Latch
Email
Tour
PTZ
activation
Alarm record function becomes activated in the specified periods.
There are six periods in one day. Please draw a circle to enable
corresponding period.
Select date. If you do not select, current setup applies to today only.
You can select all week column to apply to the whole week.
Click OK button, system goes back to alarm setup interface, please
click save button to exit.
System only memorizes one event during the anti-dither period. The
value ranges from 0 to 15s.
Enable alarm activation function. You need to select alarm output port
so that system can activate corresponding alarm device when alarm
occurred.
System can delay the alarm output for specified time after alarm
ended. The value ranges from 10 seconds to 300 seconds.
System can upload the alarm signal to the centre (Including alarm
centre.
System auto activates current channel to record once alarm occurs
(working with alarm activation function). Please note current device
shall be in auto record mode (Chapter 4.4 Schedule).
System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.
Please draw a circle to enable email function. System can send out
email to alert you when alarm occurs and ends.
Display the selected video in local monitor window.
Tour interval and tour mode are set in DVR local menu (chapter 5.3.9
Display )
Here you can set PTZ movement when alarm occurs. Such as go to
preset x when there is an alarm.
The PTZ configuration events include preset, tour, and pattern.
124
Parameter
Capture
Copy
Save
Refresh
Function
You need to input capture channel number so that system can backup
snapshot file when alarm occurs.
It is a shortcut menu button. You can copy current channel setup to
one or more (all) channels.
You can click save button after you complete setup for one channel,
or you can complete the whole setups and then click save button.
Click this button to get device latest configuration information.
7.3.2.7 Detect
Analysis the video, system enable motion detection alarm when it detects the motion signal
reached the specified sensitivity.
The detection interface is shown as in Figure 7-40.
X468H
X
Figure 7-40
Figure 7-41
125
Please refer to the following sheet for detailed information.
Parameter
Function
Event
Type
There are three types: Motion detection/video loss/Camera Masking.
Channel
Select channel name from the dropdown list.
Enable
You need to draw a circle to enable motion detection function.
Sensitivity
There are six levels. The sixth level has the highest sensitivity.
Region
z
There are six levels. The sixth level has the highest sensitivity.
z
Region: If you select motion detection type, you can click this button
to set motion detection zone. The interface is shown as in Figure
7-41. There are PAL 22X18/NTSC 22X15 zones. Right click mouse
you can go to full-screen display mode. Do remember clicking OK
button to save your motion detection zone setup.
X469H
X
Period
Anti-dither
Normal
out
z
Motion detection function becomes activated in the specified
periods.
z
There are six periods in one day. Please draw a circle to enable
corresponding period.
z
Select date. If you do not select, current setup applies to today only.
You can select all week column to apply to the whole week.
z
Click OK button, system goes back to motion detection interface;
please click save button to exit.
System only memorizes one event during the anti-dither period. The
value ranges from 0s to 15s.
z
There is 2-channel alarm output.
z
Corresponding to motion detection alarm output port(multiple
choices)
z
Enable alarm activation function. You need to select alarm output
port so that system can activate corresponding alarm device when
alarm occurs.
Alarm
latch
System can delay the alarm output for specified time after alarm end
The value ranges from 10s to 300s.
Alarm
upload
System can upload the alarm signal to the centre (Including alarm
centre.
Record
channel
System auto activates motion detection channel (multiple choices) to
record once alarm occurs (working with motion detection function).
Please note you need to go to Chapter 4.4 Schedule to set motion
detection record period and go to chapter 4.2 Manual Record to set
current period as auto record.
Record
latch
System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.
Email
If you enabled this function, System can send out email to alert you
when alarm occurs and ends.
Tour
z
Display the selected video in local monitor window.
z
Tour interval and tour mode are set in DVR local menu (chapter
5.3.9 Display )
126
Parameter
Function
PTZ
Activation
z
Capture
You need to input capture channel number so that system can backup
motion detection snapshot file.
Copy
It is a shortcut menu button. You can copy current channel setup to
one or more (all) channels.
Save
You can click save button after you complete setup for one channel,
or you can complete the whole setups and then click save button.
Refresh
Click this button to get device latest configuration information.
Here you can set PTZ movement when alarm occurs. Such as go to
preset x when there is an alarm.
7.3.2.8 PTZ
The simple lite series product does not support PTZ function.
PTZ interface is shown as in Figure 7-42
Please note, before operation please make sure you have set speed dome address. And DVR
and speed dome connection is OK.
X470H
X
Figure 7-42
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
You can select monitor channel from the dropdown list. .
Protocol
Select the corresponding dome protocol.(such as PELCOD)
Address
Set corresponding dome address. Default value is 1. Please note your
setup here shall comply with your dome address; otherwise you can
not control the speed dome.
Select the dome baud rate. Default setup is 9600.
Baud
Rate
127
Parameter
Function
Data Bit
Default setup is 8. Please set according to the speed dome dial switch
setup.
Stop bit
Default setup is 1. Please set according to the speed dome dial switch
setup.
Parity
Default setup is none. Please set according to the speed dome dial
switch setup.
Save
You can click save button after you complete setup for one channel,
or you can complete the whole setups and then click save button.
Refresh
Click this button to get device latest configuration information.
7.3.2.9 Default & Backup
Default: Restore factory default setup. You can select corresponding items.
Backup: Export current configuration to local PC or import configuration from current PC.
Please refer to Figure 7-43.
Please note system can not restore some information such as network IP address.
X471H
X
Figure 7-43
Please refer to the following sheet for detailed information.
Parameter
Function
Select All
Restore factory default setup.
Export
Configuration
Export system configuration to local PC.
Import
Configuration
Import configuration from PC to the system.
7.3.3 Advanced
7.3.3.1 HDD Management
HDD management includes net storage management and local storage management.
128
Please note, if you want to use local storage function, your storage device need to support
current function.
Please select the storage device first and then you can see the items on your right become valid.
You can check the corresponding item here. See Figure 7-44.
X472H
X
Figure 7-44
Please refer to the following sheet for detailed information.
Parameter
Function
Format
Clear data in the disk.
Read/write
Set current SD card as read/write
Read only
Set current card as read.
Recover
Recover dada after error occurs.
Please note system needs to reboot to activate current setup.
7.3.3.2 Alarm I/O
The simple lite series product does not support alarm function.
Here you can search alarm output status. See Figure 7-45.
X473H
X
129
Figure 7-45
Important
The alarm output port should not be connected to high power load directly (It shall be less than
1A) to avoid high current which may result in relay damage. Please use the co contactor to
realize the connection between the alarm output port and the load.
Please refer to the following sheet for detailed information.
Parameter
Function
Alarm output
There are three output channels (Multiple choices).
Activate
Enable/disable alarm output device. After the Web activated the
alarm, you need to cancel the channel and then click the
activation button to cancel the alarm, or you need to cancel the
alarm in the pop-up dialogue box in local-end.
Refresh
Search alarm output status.
7.3.3.3 Record
Record control interface is shown as in Figure 7-46.
X47H
X
130
Figure 7-46
Please refer to the following sheet for detailed information.
Parameter
Function
System enables auto record function as you set in record schedule
setup.
Enable corresponding channel to record no matter what period
Manual
applied in the record setup.
Stop current channel record no matter what period applied in the
Stop
record setup.
Operation here is the same to chapter 4.2 Manual Record. Please refer to chapter 4.2 for
detailed information.
Auto
7.3.3.4 Account
Here you can add, remove user or modify password. See Figure 7-47.
X475H
X
131
Figure 7-47
7.3.3.5 Auto Maintenance
X476H
Here you can select auto reboot and auto delete old files interval from the dropdown list. See
Figure 7-48.
X
Figure 7-48
132
7.3.3.6 Snapshot
Snapshot interface is shown as in Figure 7-49.
X47H
X
Figure 7-49
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
It is the monitor channel.
Snapshot mode
There are two modes: Timing and activation.
Frame rate
You can select from the dropdown list. The value ranges from
1f/s to 7f/s.
Resolution
You can select from the dropdown list.
For 16 series DVR:
Channel 1 and channel 9 support D1/CIF/QCIF.
Channel 2 to channel 8, channel 10 to channel 16 supports
CIF/QCIF.
You can select from the dropdown list. Here is for you to set
video quality.
There are six options: 10%、30%、50%、60%、80%、100
%.
100% is the best quality.
Quality
7.3.3.7 Abnormity
The abnormity interface is shown as below.
133
Figure 7-50
Please refer to the following sheet for detailed information.
Parameter
Function
Event
Type
z
The abnormal events include: no disk, no space, disk error, net error.
z
You need to draw a circle to enable this function.
Normal
Out
The corresponding alarm activation output channel when alarm occurs,
There are three channels.
Latch
The alarm output can delay for the specified time after alarm stops.
Then system disables alarm and corresponding activation output.
The value ranges from 10s to 300s.
Send
email
If you enable this function, system can send out email to alarm the
specified user.
Alarm
upload
System can upload the alarm signal to the network (includes the alarm
centre.)
Show
message
System can display alarm information in local DVR screen.
7.3.4 Additional Function
7.3.4.1 ATM/POS
The ATM/POS function is the same with the card overlay function (chapter 5.5.8). It is mainly for
financial areas to Sniffer, information parse and character overlay. The ATM/POS interface is
shown as in Figure 7-51.
134
Source IP refers to host IP address that sends out information (usually it is the device host
connected to the DVR.)
Destination IP refers to other systems that receive information.
There are total four groups IP. The record channel applies to one group (optional) only.
Six frame ID groups verification can guarantee information validity and legal.
The start position, length and data can be set according to your protocol and data packet. There
are total four fields.
Figure 7-51
7.3.4.2 Auto Register
Auto register interface is shown as below. See Figure 7-52.
Figure 7-52 Auto Register
135
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
Enable auto register function.
No.
Device management server number.
IP
Device management server IP address.
Port
Server port number.
Device ID
Device ID in the device management server.
7.3.4.3 DNS
Here you can set server or local operator DNS address. See Figure 7-53.
This function is useful when you input domain name in some item. Otherwise system can not
parse the domain name.
Figure 7-53
7.4 Search
Click search button, you can see an interface is shown as in Figure 7-54.
Please select record playback mode, and then select start time, end time and channel. Then
please click search button, you can see the corresponding files in the list.
Please note the card number search is for special series only.
136
Figure 7-54
Select the file(s) you want to download and then click download button, system pops up a
dialogue box shown as in Figure 7-55, and then you can specify file name and path to download
the file(s) to your local pc.
Figure 7-55
Now you can see system begins download and the download button becomes stop button. You
can click it to terminate current operation.
At the bottom of the interface, there is a process bar for your reference. See Figure 7-56.
137
Figure 7-56
When download completed, you can see a dialogue box shown as in Figure 7-57. Please click
OK to exit.
Figure 7-57
Please refer to the following sheet for detailed information.
Type
Parameter Function
Type
Record
Search general record, alarm record and motion detection
record.
Alarm
Search alarm record.
Motion
Search motion detection record.
Detection
Local
Search local record.
Snapshot Search snapshot file.
Card
This function is not available in current device.
Item
Begin
Set the file start time. You can select from the dropdown
time
list.
End time
Set the file end time. You can select from the dropdown
list.
Channel
Select the channel from the dropdown list.
Operation Search
Click this button you can view the recorded file matched
your requirements. There are 100 files in one screen. You
can use pg up/down button to view more files.
Playback
Select the file first and then click playback button to view
the video.
138
Type
Parameter
Download
type
Download
Open
local
record
Function
Download by file: Select the file(s) and then click
download button.
Download by time: Download the recorded file(s) within
your specified period.
Select the file you need (multiple choices) and then click
download button, you can see system pops up a dialogue
box. See Figure 7-55.
Input the downloaded file name, specify the path and then
click OK button. You can see system begins download
and the download becomes stop button. There is a
progress bar for your reference.
Select local record to play.
MultipleSystem supports playback one file in several monitor
channel
channels.
playback
During the playback process, you can see there are control buttons such as play, pause, stop.
slow play and fast play in the play process bar. You can view current playback file channel name,
time and data statistics.
In the search result interface, you can select one or more files to download to your local PC.
The playback control bar is shown as below. See Figure 7-58.
1: Play
2: Pause
3: Stop
4: Slow play
5: Fast play
139
Playback device IP address
and channel number.
Playback control bar
Figure 7-58
7.5 Alarm
Click alarm function, you can see an interface is shown as in Figure 7-59.
Here you can set device alarm type and alarm sound setup.
Figure 7-59
140
Please refer to the following sheet for detailed information.
Please make sure current device can upload the alarm.
Type
Parameter
Function
Alarm
Video loss
System alarms when video loss occurs.
Type
Motion detection System alarms when motion detection alarm
occurs,
Disk full
System alarms when disk is full.
Disk error
System alarms when disk error occurs.
Camera
System alarms when camera is viciously masking.
masking
Encode alarm
System alarms when peripheral device alarms.
External alarm
Alarm input device sends out alarm.
Operation Listen alarm
System notifies web when alarm occurs (you select
from the above event type), and then web can
notify user.
Video
When alarm occurs, system auto enables video
monitor. This function only applies to video
detection alarm (motion detection, video loss and
camera masking).
Prompt
Automatically pops up alarm dialogue box.
Sound pop up
System sends out alarm sound when alarm occurs.
You can specify as you wish.
Path
Here you can specify alarm sound file.
7.6 About
Click about button, you can view current web client information. See Figure 7-60.
Figure 7-60
7.7 Log out
Click log out button, system goes back to log in interface. See Figure 7-61.
You need to input user name and password to login again.
141
Figure 7-61
7.8 Un-install Web Control
You can use web un-install tool “uninstall web.bat” to un-install web control.
Please note, before you un-installation, please close all web pages, otherwise the uninstallation might result in error.
142
8 Professional Surveillance System
Besides Web, you can use our Professional Surveillance Software (PSS) to login the device.
For detailed information, please refer to PSS user’s manual.
143
9 FAQ
1. DVR can not boot up properly.
There are following possibilities:
z
Input power is not correct.
z
Power connection is not correct.
z
Power switch button is damaged.
z
Program upgrade is wrong.
z
HDD malfunction or something wrong with HDD ribbon.
z
Seagate DB35.1,DB35.2,SV35 or Maxtor 17-g has compatibility problem. Please
upgrade to the latest version to solve this problem.
z
Front panel error.
z
Main board is damaged.
2. DVR often automatically shuts down or stops running.
There are following possibilities:
z
Input voltage is not stable or it is too low.
z
HDD malfunction or something wrong wit the ribbon.
z
Button power is not enough.
z
Front video signal is not stable.
z
Working environment is too harsh, too much dust.
z
Hardware malfunction.
3. System can not detect hard disk.
There are following possibilities:
z
HDD is broken.
z
HDD ribbon is damaged.
z
HDD cable connection is loose.
z
Main board SATA port is broken.
4. There is no video output whether it is one-channel, multiple-channel or all-channel
output.
There are following possibilities:
z
Program is not compatible. Please upgrade to the latest version.
z
Brightness is 0. Please restore factory default setup.
z
There is no video input signal or it is too weak.
z
Check privacy mask setup or your screen saver.
z
DVR hardware malfunctions.
5. Real-time video color is distorted.
There are following possibilities:
z
When using BNC output, NTSC and PAL setup is not correct. The real-time video
becomes black and white.
z
DVR and monitor resistance is not compatible.
z
Video transmission is too long or degrading is too huge.
144
z
DVR color or brightness setup is not correct.
6. Can not search local records.
There are following possibilities:
z
HDD ribbon is damaged.
z
HDD is broken.
z
Upgraded program is not compatible.
z
The recorded file has been overwritten.
z
Record function has been disabled.
7. Video is distorted when searching local records.
There are following possibilities:
z
Video quality setup is too low.
z
Program read error, bit data is too small. There is mosaic in the full screen. Please
restart the DVR to solve this problem.
z
HDD data ribbon error.
z
HDD malfunction.
z
DVR hardware malfunctions.
8. There is no audio when monitor.
There are following possibilities:
z
It is not a power picker.
z
It is not a power acoustics.
z
Audio cable is damaged.
z
DVR hardware malfunctions.
9. There is audio when monitor but there is no audio when system playback.
There are following possibilities:
z
Setup is not correct. Please enable audio function
z
Corresponding channel has no video input. Playback is not continuous when the screen
is blue.
10. Time display is not correct.
There are following possibilities:
z
Setup is not correct
z
Battery contact is not correct or voltage is too low.
z
Crystal is broken.
11. DVR can not control PTZ.
There are following possibilities:
z
Front panel PTZ error
z
PTZ decoder setup, connection or installation is not correct.
z
Cable connection is not correct.
z
PTZ setup is not correct.
z
PTZ decoder and DVR protocol is not compatible.
145
z
PTZ decoder and DVR address is not compatible.
z
When there are several decoders, please add 120 Ohm between the PTZ decoder A/B
cables furthest end to delete the reverberation or impedance matching. Otherwise the
PTZ control is not stable.
z
The distance is too far.
12. Motion detection function does not work.
There are following possibilities:
z
Period setup is not correct.
z
Motion detection zone setup is not correct.
z
Sensitivity is too low.
z
For some versions, there is hardware limit.
13. Can not log in client-end or web.
There are following possibilities:
z
For Windows 98 or Windows ME user, please update your system to Windows 2000
sp4. Or you can install client-end software of lower version. Please note right now, our
DVR is not compatible with Windows VISTA control.
z
ActiveX control has been disabled.
z
No dx8.1 or higher. Please upgrade display card driver.
z
Network connection error.
z
Network setup error.
z
Password or user name is invalid.
z
Client-end is not compatible with DVR program.
14. There is only mosaic no video when preview or playback video file remotely.
There are following possibilities:
z
Network fluency is not good.
z
Client-end resources are limit.
z
There is multiple-cast group setup in DVR. This mode can result in mosaic. Usually we
do not recommend this mode.
z
There is privacy mask or channel protection setup.
z
Current user has no right to monitor.
z
DVR local video output quality is not good.
15. Network connection is not stable.
There are following possibilities:
z
Network is not stable.
z
IP address conflict.
z
MAC address conflict.
z
PC or DVR network card is not good.
16. Burn error /USB back error.
There are following possibilities:
z
Burner and DVR are in the same data cable.
146
z
System uses too much CPU resources. Please stop record first and then begin backup.
z
Data amount exceeds backup device capacity. It may result in burner error.
z
Backup device is not compatible.
z
Backup device is damaged.
17. Keyboard can not control DVR.
There are following possibilities:
z
DVR serial port setup is not correct
z
Address is not correct
z
When there are several switchers, power supply is not enough.
z
Transmission distance is too far.
18. Alarm signal can not been disarmed.
There are following possibilities:
z
Alarm setup is not correct.
z
Alarm output has been open manually.
z
Input device error or connection is not correct.
z
Some program versions may have this problem. Please upgrade your system.
19. Alarm function is null.
There are following possibilities:
z
Alarm setup is not correct.
z
Alarm cable connection is not correct.
z
Alarm input signal is not correct.
z
There are two loops connect to one alarm device.
20. Remote control does not work.
There are following possibilities:
z
Remote control address is not correct.
z
Distance is too far or control angle is too small.
z
Remote control battery power is low.
z
Remote control is damaged or DVR front panel is damaged.
21. Record storage period is not enough.
There are following possibilities:
z
Camera quality is too low. Lens is dirty. Camera is installed against the light. Camera
aperture setup is not correct.
z
HDD capacity is not enough.
z
HDD is damaged.
22. Can not playback the downloaded file.
There are following possibilities:
z
There is no media player.
z
No DXB8.1 or higher graphic acceleration software.
147
z
There is no DivX503Bundle.exe control when you play the file transformed to AVI via
media player.
z
No DivX503Bundle.exe or ffdshow-2004 1012 .exe in Windows XP OS.
23. Forget local menu operation password or network password
Please contact your local service engineer or our sales person for help. We can guide you to
solve this problem.
148
Appendix A HDD Capacity Calculation
Calculate total capacity needed by each DVR according to video recording (video recording type
and video file storage time).
Step 1: According to Formula (1) to calculate storage capacity qi that is the capacity of each
channel needed for each hour, unit Mbyte.
qi = d i ÷ 8 × 3600 ÷ 1024
(1)
In the formula: d i means the bit rate, unit Kbit/s
Step 2: After video time requirement is confirmed, according to Formula (2) to calculate the
storage capacity mi , which is storage of each channel needed unit Mbyte.
mi = qi × hi × Di
(2)
In the formula:
hi means the recording time for each day (hour)
Di means number of days for which the video shall be kept
Step 3: According to Formula (3) to calculate total capacity (accumulation) qT that is needed for
all channels in the DVR during scheduled video recording.
c
qT = ∑ mi
(3)
i =1
In the formula: c means total number of channels in one DVR
Step 4: According to Formula (4) to calculate total capacity (accumulation) qT that is needed for
all channels in DVR during alarm video recording (including motion detection).
c
qT = ∑ mi ×a%
(4)
i =1
In the formula:a% means alarm occurrence rate
149
Appendix B Compatible USB Drive List
NOTE: Please upgrade the DVR firmware to latest version to ensure the accuracy of the table
below. If you use the USB drive, please confirm the format FAT or FAT32.
Manufacturer
Model
Capacity
Sandisk
Cruzer Micro
512M
Sandisk
Cruzer Micro
1G
Sandisk
Cruzer Micro
2G
Sandisk
Cruzer Freedom
256M
Sandisk
Cruzer Freedom
512M
Sandisk
Cruzer Freedom
1G
Sandisk
Cruzer Freedom
2G
DataTraveler Ⅱ
Kingston
1G
DataTraveler Ⅱ
Kingston
2G
Kingston
DataTraveler
1G
Kingston
DataTraveler
2G
Maxell
USB Flash Stick
128M
Maxell
USB Flash Stick
256M
Maxell
USB Flash Stick
512M
Maxell
USB Flash Stick
1G
Maxell
USB Flash Stick
2G
Kingax
Super Stick
128M
Kingax
Super Stick
256M
Kingax
Super Stick
512M
Kingax
Super Stick
1G
Kingax
Super Stick
2G
Netac
U210
128M
Netac
U210
256M
Netac
U210
512M
Netac
U210
1G
Netac
U210
2G
Teclast
Ti Cool
128M
Teclast
Ti Cool
256M
Teclast
Ti Cool
512M
Teclast
Ti Cool
1G
Teclast
Ti Cool
2G
150
Appendix C Compatible CD/DVD Burner List
NOTE: Please upgrade the DVR firmware to latest version to ensure the accuracy of the table
below. And you can use the USB cable with the model recommended to set USB burner.
Manufacturer
Model
Port Type
Type
Sony
DRX-S50U
USB
DVD-RW
Sony
DRX-S70U
USB
DVD-RW
Sony
AW-G170S
SATA
DVD-RW
Samsung
TS-H653A
SATA
DVD-RW
Panasonic
SW-9588-C
SATA
DVD-RW
Sony
DRX-S50U
USB
DVD-RW
BenQ
5232WI
USB
DVD-RW
151
Appendix D Compatible SATA HDD List
NOTE: Please upgrade the DVR firmware to latest version to ensure the accuracy of the table
below. And SATA HDD should be used for the DVR with SATA port.
Port
Manufacturer
Series
Model
Capacity
Mode
Seagate
Barracuda.10
ST3750640AS
750G
SATA
Seagate
Barracuda.10
ST3500630AS
500G
SATA
Seagate
Barracuda.10
ST3400620AS
400G
SATA
Seagate
Barracuda.10
ST3320620AS
320G
SATA
Seagate
Barracuda.10
ST3250620AS
250G
SATA
Seagate
Barracuda.10
ST3250820AS
250G
SATA
Seagate
Barracuda.10
ST3160815AS
160G
SATA
Seagate
Barracuda.10
ST380815AS
80G
SATA
Seagate
Barracuda.9
ST3160811AS2
160G
SATA
Seagate
Barracuda.9
ST3120811AS2
120G
SATA
Seagate
Barracuda.9
ST380811AS2
80
SATA
Seagate
Barracuda.9
ST380211AS2
80G
SATA
Seagate
Barracuda.11
ST3750330AS
750G
SATA
Seagate
Barracuda.11
ST3500320AS
500G
SATA
Seagate
Barracuda 7200.11
ST31500341AS
1.5T
SATA
Seagate
Seagate
Pipeline HD.2
ST3320311CS
350G
ST3160815SV
160G
Seagate
SV35.2
SV35.2
SATA
SATA
ST3250310SV
250G
SATA
Seagate
SV35.2
ST3320620SV
320G
SATA
Seagate
SV35.2
ST3500320SV
500G
SATA
Seagate
SV35.2
ST3750640SV
750G
SATA
Seagate
SV35.3
ST31000340SV
1T
SATA
Maxtor
DiamondMax 20
STM3320820AS
320G
SATA
Maxtor
DiamondMax 20
STM3250820AS
250G
SATA
Maxtor
DiamondMax 21
STM3160211AS
160G
SATA
Maxtor
DiamondMax 21
STM380211AS
80G
SATA
Maxtor
DiamondMax 21
STM340211AS
40G
SATA
Western Digital
Cariar SE
WD3200JD
320G
SATA
Western Digital
Cariar SE
WD3000JD
300G
SATA
Western Digital
Cariar SE
WD2500JS
250G
SATA
Western Digital
Cariar SE
WD2000JD
200G
SATA
Western Digital
Cariar SE
WD1600JD
160G
SATA
Western Digital
Cariar SE
WD1600JS
160G
SATA
Western Digital
Cariar SE
WD1200JS
120G
SATA
Western Digital
Cariar SE
WD800JD
80G
SATA
Western Digital
Cariar
WD1600AABS2
160G
SATA
Western Digital
Cariar
WD800BD
80G
SATA
Western Digital
Cariar SE16
WD7500KS2
750G
SATA
152
Western Digital
Cariar SE16
WD5000KS2
500G
SATA
Western Digital
Cariar SE16
WD4000KD2
400G
SATA
Western Digital
Cariar SE16
WD3200KS2
320G
SATA
Western Digital
Cariar SE16
WD2500KS2
250G
SATA
Western Digital
RE series
WD5000ABYS
500G
SATA
Western Digital
Caviar Green series
WD20EADS
2T
SATA
Samsung
/
HA101UJ/CE
1T
SATA
153
Appendix E Compatible Displayer List
Please refer to the following sheet form compatible displayer list.
Brand
Model
BENQ(LCD)
ET-0007-TA
DELL(LCD)
E178FPc
BENQ(LCD)
Q7T4
BENQ(LCD)
Q7T3
LENOVO(LCD)
LXB-L17C
SANGSUNG(LCD)
225BW
LENOVO(CRT)
LXB-FD17069HB
LENOVO(CRT)
LXB-HF769A
LENOVO(CRT)
LX-GJ556D
Samsung (LCD)
2494HS
Samsung (LCD)
P2350
Samsung (LCD)
P2250
Samsung (LCD)
P2370G
Samsung (LCD)
2043
Samsung (LCD)
2243EW
LG(LCD)
W1942SP
LG(LCD)
W2243S
LG(LCD)
W2343T
BENQ(LCD)
G900HD
BENQ(LCD)
G2220HD
PHILIPS(LCD)
230E
PHILIPS(LCD)
220CW9
PHILIPS(LCD)
220BW9
PHILIPS(LCD)
220EW9
Dimension (Unit: inch)
19-inch (wide screen)
17-inch
17-inch
17-inch
17-inch
22-inch (wide screen)
17-inch
17-inch
17-inch
24-inch
23-inch
22-inch
23-inch
20-inch
22-inch
19-inch
22-inch
23-inch
18.5-inch
22-inch
23-inch
23-inch
24-inch
25-inch
154
Appendix F Earthing
1. What is the surge?
Surge is a short current or voltage change during a very short time. In the circuit, it lasts for
microsecond. In a 220V circuit, the 5KV or 10KV voltage change during a very short time (about
microseconds) can be called a surge. The surge comes from two ways: external surge and
internal surge.
z The external surge: The external surge mainly comes from the thunder lightning. Or it comes
from the voltage change during the on/off operation in the electric power cable.
z The internal surge: The research finds 88% of the surge from the low voltage comes from
the internal of the building such as the air conditioning, elevator, electric welding, air
compressor, water pump, power button, duplicating machine and other device of inductive
load.
The lightning surge is far above the load level the PC or the micro devices can support. In most
cases, the surge can result in electric device chip damage, PC error code, accelerating the part
aging, data loss and etc. Even when a small 20 horsepower inductive engine boots up or stops,
the surge can reach 3000V to 50000V, which can adversely affect the electronic devices that use
the same distribution box.
To protect the device, you need to evaluate its environment, the lighting affection degree
objectively. Because surge has close relationship with the voltage amplitude, frequency, network
structure, device voltage-resistance, protection level, ground and etc. The thunder proof work
shall be a systematic project, emphasizing the all-round protection (including building,
transmission cable, device, ground and etc.). There shall be comprehensive management and
the measures shall be scientific, reliable, practical and economic. Considering the high voltage
during the inductive thundering, the International Electrotechnical Committee (IEC) standard on
the energy absorbing step by step theory and magnitude classification in the protection zone, you
need to prepare multiple precaution levels.
You can use the lightning rod, lightning strap or the lightning net to reduce the damage to the
building, personal injury or the property,
z
z
The lightning protection device can be divided into three types:
Power lightning arrester: There are 220V single-phrase lightning arrester and 380V threephrase lightening arrester (mainly in parallel connection, sometimes use series connection )
You can parallel connect the power lightning arrester in the electric cable to reduce the
short-time voltage change and release the surge current. From the BUS to the device, there
are usually three levels so that system can reduce the voltage and release the current step
by step to remove the thunderstorm energy and guarantee the device safety. You can select
the replaceable module type, the terminal connection type and portable socket according to
your requirement.
Signal lightning arrester: This device is mainly used in the PC network, communication
system. The connection type is serial connection. Once you connected the signal lightning
arrestor with the signal port, it can cut the channel of the thunderstorm to the device, and on
the other hand, it can discharge the current to the ground to guarantee the device proper
155
work. The signal lightning arrester has many specifications, and widely used in many
devices such as telephone, network, analog communication, digital communication, cable
TV and satellite antenna. For all the input port, especially those from the outdoor, you need
to install the signal lightning arrester.
z Antenna feed cable lightning arrester: It is suitable for antenna system of the transmitter or
the device system to receive the wireless signal. It uses the serial connection too.
Please note, when you select the lighting arrester, please pay attention to the port type and the
earthing reliability. In some important environment, you need to use special shielded cable. Do
not parallel connect the thunder proof ground cable with the ground cable of the lightning rod.
Please make sure they are far enough and grounded respectively.
2. The earthing modes
We all know the earthing is the most complicated technology in the electromagnetism
compatibility design since there is no systematic theory or module. The earthing has many
modes, but the selection depends on the system structure and performance. The following are
some successfully experience from our past work.
One-point ground: In the following figure you can see there is a one-point ground. This
connection provides common port to allow signal to be transmitted in many circuits. If there is no
common port, the error signal transmission occurred. In the one-point ground mode, each circuit
is just grounded only and they are connected at the same port. Since there is only one common
port, there is no circuit and so, there is no interference.
Multiple-point ground: In the following figure, you can see the internal circuit uses the chassis
as the common point. While at the same time, all devices chassis use the earthing as the
common port. In this connection, the ground structure can provide the lower ground resistance
because when there are multiple-point grounds; each ground cable is as short as possible. And
the parallel cable connection can reduce the total conductance of the ground conductor. In the
high-frequency circuit, you need to use the multiple-point ground mode and each cable needs to
connect to the ground. The length shall be less than the 1/20 of the signal wavelength.
156
Mixed ground: The mix ground consists of the feature of the one-point ground and multiple-point
ground. For example, the power in the system needs to use the one-point ground mode while the
radio frequency signal requires the multiple-point ground. So, you can use the following figure to
earth. For the direct current (DC), the capacitance is open circuit and the circuit is one-point
ground. For the radio frequency signal, the capacitance is conducive and the circuit adopts
multiple-point ground.
When connecting devices of huge size (the device physical dimension and connection cable is
big comparing with the wave path of existed interference), then there are possibility of
interference when the current goes through the chassis and cable. In this situation, the
interference circuit path usually lies in the system ground circuit.
When considering the earthing, you need to think about two aspects: The first is the system
compatibility, and the other is the external interference coupling into the earth circuit, which
results in system error. For the external interference is not regular, it is not easy to resolve.
3. Thunder proof ground method in the monitor system
z
z
z
z
z
The monitor system shall have sound thunder proof earthing to guarantee personnel safety
and device safety.
The monitor system working ground resistance shall be less than 1Ω.
The thunder proof ground shall adopt the special ground cable from the monitor control room
to the ground object. The ground cable adopts copper insulation cable or wire and its ground
section shall be more than 20mm2.
The ground cable of the monitor system can not short circuit or mixed connected with the
strong alternative current cable.
For all the ground cables from the control room to the monitor system or ground cable of
other monitor devices, please use the copper resistance soft cable and its section shall be
more than 4mm2.
157
z
z
The monitor system usually can adopt the one-point ground.
Please connect the ground end of 3-pin socket in the monitor system to the ground port of
the system (protection ground cable)
4. The shortcut way to check the electric system using the digital multimeter
For 220V AC socket, from the top to the bottom, E (ground cable), N (neutral cable), L(live cable).
Please refer to the following figure.
There is a shortcut way to check these thee cables connection are standard or not (not the
accurate check).
Importance
In the following operations, the multimeter range shall be at 750V!
For E (earth cable)
Turn the digital multimeter to 750V AC, use your one hand to hold the metal end, and then the
other hand insert the pen to the E port of the socket. See the following figure. If the multimeter
shows 0, then you can see current earth cable connection is standard. If the value is more than
10, then you can see there is inductive current and the earth cable connection is not proper.
osvaldo parra
tecnico en telecomunicaciones
158
For L (live cable)
Turn the digital multimeter to 750V AC, use your one hand to hold the metal end, and then the
other hand insert the pen to the L port of the socket. See the following figure. If the multimeter
shows 120, then you can see current live cable connection is standard. If the value is less than
60, then you can see current live cable connection is not proper or it is not the live cable at all.
For N (Neutral cable)
Turn the digital multimeter to 750V AC, use your one hand to hold the metal end, and then the
other hand insert the pen to the N port of the socket. See the following figure. If the multimeter
shows 0, then you can see current N cable connection is standard. If the value is more than 10,
then you can see there is inductive current and the neutral cable connection is not proper. If the
value is 120, then you can know misconnected the neutral cable to the live cable.
Note:
z
This manual is for reference only. Slight difference may be found in the user interface.
z
All the designs and software here are subject to change without prior written notice.
z
If there is any uncertainty or controversy, please refer to the final explanation of ours.
z
Please visit our website or contact your local retailer for more information.
159