INST 4644
KIT COMPONENTS
(4) Hex-head
Screws
Radio
Housing
(4) Studs
Flat
Faceplate
99-4644
INSTALLATION
INSTRUCTIONS
½"
Faceplate
1"
Faceplate
Rear Support
Tray
ISO
Trimring
APPLICATIONS
GENERAL MOTORS 1982-02
VEHICLES EQUIPPED WITH J-2000 PANEL-STYLE
FACTORY HEAD UNIT PROVISIONS
(SEE INSIDE FOR SPECIFIC APPLICATIONS)
ISO
Brackets
(4) Nuts
Bracket Set #1
Bracket #3
Bracket
Set #2
Bracket #4
Bracket
#(L) S-10
Bracket Set #5
Bracket #7
Bracket #6
Bracket
Set #8
Bracket
Set #9
1-800-221-0932
rev. 150202
Bracket Set #10
www.metraonline.com
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
NOTES: ______________________________________________________
TABLE OF CONTENTS
CAR
PAGE
BUICK
Century 1982-96*........................1
Electra 1984-94*......................... 1
Estate wagon 1984-94*.............. 1
LeSabre 1984-94*.......................1
Park Ave. 1984-94*.....................1
Reatta 1990-91*..........................2
Regal 1984-87*........................... 2
Riviera 1983-85*......................... 3
Riviera 1990-95*......................... 3
Roadmaster 1991-94.................. 4
Skyhawk 1982-89*...................... 4
Skylark 1983-85*.........................5
Skylark 1987-89*.........................5
Skylark 1990-95*........................ 6
CADILLAC
Cimarron 1982-88.......................13
DeVille 1985-93*......................... 6
Eldorado 1984-91*...................... 7
Escalade 1999-02....................... 7
Fleetwood 1985-93*....................6
Seville 1984-91*..........................7
CHEVROLET
Astro 1985-89............................. 8
Astro 1990-95............................. 8
Astro 1996-02............................. 9
Beretta 1991-96.......................... 9
Blazer (full) 1989-91*.................. 10
Blazer 1998-02............................10
Camaro 1982-84......................... 11
Camaro 1985-92......................... 11
Camaro 1997-99.........................12
Caprice 1991-93......................... 4
Caprice 1994-96......................... 12
Cavalier 1982-90.........................13
Cavalier 1991-94.........................13
Cavalier 1995-99.........................14
Celebrity 1982-83*...................... 14
Celebrity 1984-87*...................... 15
Citation II 1985*.......................... 15
Corsica 1991-96......................... 9
Corvette 1984-89*.......................16
Corvette 1997-02........................ 16
El Camino 1985-88..................... 17
Express 1996-00.........................17
Impala SS 1994-96..................... 12
Lumina 1990-94..........................18
Lumina 1995-99..........................18
Lumina APV 1990-95..................19
Lumina APV 1996.......................19
Malibu 1997-99........................... 20
Monte Carlo 1985-88.................. 17
Monte Carlo 1995-99.................. 18
Nova 1985-88............................. 20
Pickup 1995-02........................... 7
S10 Blazer 1982-85.................... 21
S10 Blazer 1986-94.................... 21
S10 Pickup 1982-85....................21
S10 Pickup 1986-93....................21
S10 Pickup 1998-02....................10
Silverado 1999-02.......................7
CAR
PAGE
CHEVROLET (cont.)
Suburban 1989-91*.....................10
Suburban 1995-02...................... 7
Tahoe 1995-02............................7
Van (full) 1988-95........................22
Venture 1997-99......................... 22
GMC
Jimmy (full) 1989-91*..................10
Jimmy 1998-02........................... 10
S15 Jimmy 1982-85....................21
S15 Jimmy 1986-94....................21
S15 Pickup 1982-85....................21
S15 Pickup 1986-93....................21
Safari 1985-89............................ 8
Safari 1990-95............................ 8
Safari 1996-02............................ 9
Savana 1996-00..........................17
Sierra 1995-02............................ 7
Sonoma 1998-02........................ 10
Suburban 1989-91*.....................10
Suburban 1995-99...................... 7
Van (full) 1988-95........................22
Yukon 1995-02............................7
OLDSMOBILE
Achieva 1992-95*........................23
Bravada 1991-94........................ 21
Cutlass Calais 1984-91*............. 24
Cutlass Ciera 1982-96*...............24
Cutlass Supreme 1984-88*..........25
Delta 88 1986-88*.......................23
Firenza 1982-89*........................ 4
Ninety-Eight 1984-90*.................23
Omega 1983-84..........................25
Silhouette 1990-95......................19
Silhouette 1996...........................19
Silhouette 1997-99......................22
Toronado 1982-85*.....................26
PONTIAC
6000 1982-91..............................26
Bonneville 1982-86*....................31
Bonneville 1987-93*....................27
Bonneville 1994-99..................... 27
Fiero 1984-88*............................ 28
Firebird 1982-84..........................11
Firebird 1985-92..........................11
Firebird 1993-02..........................28
Grand Am 1985-91*....................29
Grand Am 1992-95*....................29
Grand Am 1996-98..................... 30
Grand Am 1999-00..................... 30
Grand Prix 1985-87*................... 31
Grand Prix 1990-93.....................31
Grand Prix 1994-96.....................32
Grand Prix 1997-00.....................32
Montana 1999.............................22
Sunbird J-2000 1982-88............. 13
Sunfire 1995-99.......................... 33
TransSport 1990-95....................19
TransSport 1996......................... 19
TranSport 1997-98......................22
SATURN
(all models) 1991-94................... 33
* THE FACTORY MOUNTING BRACKET(S) MUST BE RETAINED AND USED WITH THIS VEHICLE.
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
37
NOTES: ______________________________________________________
________________________________________________________________
BUICK Century 1982-96
1
2
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
(S10 APPLICATION
SHOWN AS EXAMPLE)
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) screws from the top-inside edge of the
dash trim bezel. Remove (5) screws from
both sides of the steering column. Remove
(3) Phillips screws securing the rockerswitch housing and lift the housing out.
Remove the bezel.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
________________________________________________________________
________________________________________________________________
BUICK Electra / Estate Wagon
LeSabre / Park Avenue 1984-94
________________________________________________________________
________________________________________________________________
________________________________________________________________
1
2
________________________________________________________________
________________________________________________________________
________________________________________________________________
(S10 APPLICATION
SHOWN AS EXAMPLE)
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
36
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unsnap
the climate control trim bezel and remove (4)
star-drive screws exposed. Pull the steering
collar back and carefully unsnap the dash
trim bezel.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
1
BUICK Reatta 1990-91
4
Fig. A
1
2
Fig. B
(S10 APPLICATION
SHOWN AS EXAMPLE)
Fig. C
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) torx-head screws above the instrument
panel. Remove (1) torx-head screw from
each a/c vent. Unclip the dash trim bezel
and remove.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
BUICK Regal 1984-87
1
2
2-SHAFT HEAD UNITS: Slide the aftermarket head unit into the kit and secure with shaft nuts
(see Fig. A).
DIN HEAD UNITS: Slide the DIN cage into the kit and secure by bending the metal locking
tabs down. Slide the aftermarket head unit into the cage until secure (see Fig. B).
ISO HEAD UNITS: Slide the head unit into the radio opening, align the holes in the head unit
with the holes in the ISO Brackets and mount the unit to the brackets with the screws supplied
with the unit (see Fig. C).
5
A
6
B
C
D
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the radio knobs and cigarette lighter. Gently
unclip the radio trim bezel and remove.
2
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
Re-connect the battery terminal and test the unit
for proper operation. Mount the head unit/kit
assembly to the sub-dash with those screws
previously removed in step #1.
35
ALL VEHICLES
BUICK Riviera 1983-85
3
1
2
Fig. A
(S10 APPLICATION
SHOWN AS EXAMPLE)
Fig. B
Disconnect the negative battery terminal to
prevent an accidental short circuit. Carefully
pull and remove the dash trim bezel.
Remove (4) screws securing the factory
head unit and disconnect the wiring.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
BUICK Riviera 1990-95
Fig. C
2-SHAFT HEAD UNITS: Choose a Faceplate (according to the desired installation depth).
Snap the Faceplate onto the front of the Radio Housing and secure with (4) Hex-head
Screws supplied. Secure the Mounting Brackets to the Radio Housing with Studs and Nuts
supplied. Snap the Rear Support Tray onto the back of the Radio Housing (see Fig. A).
DIN HEAD UNITS: Choose a Faceplate (according to the desired installation depth). Cut and
remove the shaft supports from the Faceplate. Snap the Faceplate onto the front of the Radio
Housing and secure with (4) Hex-head Screws supplied. Secure the Mounting Brackets to
the Radio Housing with Studs and Nuts supplied. Snap the Rear Support Tray onto the back
of the Radio Housing (see Fig. B).
ISO HEAD UNITS: Choose a Faceplate (according to the desired installation depth). Cut and
remove the shaft supports from the Faceplate. Snap the Faceplate onto the front of the Radio
Housing and secure with (4) Hex-head Screws supplied. Snap the ISO Trimring into the
back of the Faceplate. Secure the Mounting Brackets to the Radio Housing with Studs and
Nuts supplied. Slide the ISO Brackets onto the Rear Support Tray and snap the Tray onto
the back of the Radio Housing (see Fig. C).
34
1
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) torx-head screws above the instrument
cluster and (1) torx-head screw from each
a/c vent. Unsnap the panel.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
3
PONTIAC Sunfire 1995-99
BUICK Roadmaster 1991-94
CHEVROLET Caprice 1991-93
1
1
2
2
"B"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws from the driver's side service
panel and unclip the panel. Pry off the trim
piece located above the glove box and
remove (1) screw. Remove (3) screws from
the top edge of the dash trim bezel. Remove
(1) screw from the lower-left corner of the
glove box and (1) screw from the parking
brake release. Remove the dash trim bezel.
Cut and remove all mounting tabs on
Bracket #4 EXCEPT tabs "B".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Open
the glove box and remove (2) Phillips screws
exposed on the right edge of the radio trim
bezel.
Unclip the bezel and remove.
Remove (2) 7mm hex-head screws securing
the factory head unit and disconnect the
wiring.
BUICK Skyhawk / OLDSMOBILE Firenza 1982-89
1
2
Locate Bracket Set #9.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
SATURN (all models) 1991-94
1
2
"A"
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the glove box by removing the doorstrap
wire clip and (4) screws. Remove (2) screws
below the cigarette lighter housing and (3)
screws below the steering column. Remove
(1) screw from the top-left of the factory head
unit and unclip the dash trim bezel.
4
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
"A"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Gently
unclip the dash trim bezel. Remove (2)
screws from the factory head unit and
disconnect the wiring.
Cut and remove all mounting tabs on
Bracket #6 EXCEPT tabs "A".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
33
PONTIAC Grand Prix 1994-96
1
2
BUICK Skylark 1983-85
1
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Using a
small set of pliers, grasp the retaining clip on
the back of the gear shifter handle and
remove the clip. Remove the gear shifter
handle. Unclip the center console and
remove.
Remove (2) 7mm hex-head
screws exposed under the climate controls.
Unclip the radio trim bezel and remove.
Remove (2) 7mm hex-head screws securing
the factory head unit and disconnect the
wiring.
Locate Bracket Set #9.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) screws from the top edge of the
instrument panel. Remove (1) screw from
the bottom-left corner of the panel. Remove
(2) screws from the steering column trim and
remove the trim. Pull up and out on the dash
trim bezel and remove.
BUICK Skylark 1987-89
PONTIAC Grand Prix 1997-00
1
2
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
1
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the entire dash trim bezel. Remove the
screws securing the factory head unit and
disconnect the wiring.
32
Locate Bracket Set #9.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unsnap
the gear shifter bezel from the base of the
console. Remove (2) screws securing the
bottom of the dash trim bezel and remove
the bezel.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
5
BUICK Skylark 1990-95
2
1
PONTIAC Grand Prix 1985-87 / Bonneville 1982-86
1
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Pull out
on the ashtray and remove (2) screws
exposed in the ashtray cavity. Remove (2)
screws securing the front of the ashtray and
lower section of the dash trim bezel. Using a
panel removal tool, gently pry out on the trim
bezel and remove. Remove (2) nuts from
the bottom of the factory head unit and
disconnect the wiring.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(3) screws from the top edge of the dash
trimbezel. Remove (4) screws from the
metal steering column trim and remove the
trim. Remove (4) screws exposed at the
bottom edge of the dash trim bezel.
Remove the cigarette lighter and retainer
ring and remove the dash trim bezel.
PONTIAC Grand Prix 1990-93
CADILLAC Deville / Fleetwood 1985-93
1
2
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
1
2
"B"
"B"
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws from the top of the radio trim
bezel. Pull out on the top edge of the bezel
and lift up to remove.
6
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(1) 9/32" hex-head screw from the computer
diagnostic plug and twist to access (1) 9/32"
screw on the trim panel. Remove (3) 9/32"
screws from the bottom edge of the panel
and remove. Open the glove box and
remove (4) 9/32" screws from the dash trim
bezel.
Cut and remove all mounting tabs on
Bracket #6 EXCEPT tabs "B".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
31
PONTIAC Grand Am 1996-98
1
2
CADILLAC Eldorado / Seville 1984-91
1
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) Phillips screws from the pocket. Remove
(2) Phillips screws above the instrument
cluster. Unclip the dash trim bezel and
remove.
Remove (3) 7mm hex-head
screws securing the factory head unit and
disconnect the wiring.
Locate Bracket Set #9.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) Phillips screws above the a/c vents. Pull
out on the top edge of the dash trim bezel
unhook the bottom edge and remove.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
CADILLAC Escalade 1999-02
CHEVROLET Pickup/Suburban/Tahoe 1995-02 · Silverado 1999-02
GMC Sierra/Suburban/Yukon 1995-02
PONTIAC Grand Am 1999-00
1
1
2
2
Illustration not
available when
printed
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the radio trim bezel. Remove (3) 9/32"
screws securing the factory head unit and
disconnect the wiring.
30
Locate Bracket Set #9.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove the
steering column filler panel and the ashtray.
Unclip the dash trim bezel and remove. Using a
small flat-blade screwdriver, press down on the
outer clips of the factory head unit (or pocket).
Disconnect the wiring and remove the unit.
Locate Bracket Set #8. Skip to the
Installation Instructions for ALL
VEHICLES on Page #34.
7
CHEVROLET Astro / GMC Safari 1985-89
1
2
PONTIAC Grand Am 1985-91
1
2
"A"
"A"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(3) Phillips screws from the top portion of the
dash trim bezel. Open the glove box and
remove (2) 10mm bolts from the lower edge
of the trim bezel. Pull the console trim
forward and remove (2) 7mm bolts exposed.
Gently unclip and remove the trim bezel.
Remove (2) 7mm screws from the factory
head unit and disconnect the wiring.
Cut and remove all mounting tabs on
Bracket #3 EXCEPT tabs "A".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Carefully
unsnap the front edge of the gear shifter
console panel. Unsnap and remove the
dash trim bezel.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
PONTIAC Grand Am 1992-95
CHEVROLET Astro / GMC Safari 1990-95
1
1
2
2
"A"
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws from the bottom of the dash trim
bezel. Gently unclip and remove the bezel.
Remove (4) screws from the factory head
unit and disconnect the wiring.
8
Cut and remove all mounting tabs on
Bracket #1 EXCEPT tabs "A".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(6) 7mm hex-head screws from the driver's
side knee bolster panel and lower the panel.
Remove (4) Phillips screws from the glove
box/cupholder assembly. Remove (1) 7mm
hex-head screw from the left corner of the
dash trim bezel. Loosen (2) 10mm nuts from
the top of the factory head unit, slide the unit
out and disconnect the wiring.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
29
CHEVROLET Astro / GMC Safari 1996-02
PONTIAC Fiero 1984-88
1
2
1
2
Illustration not
available
when printed
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) star-drive screws from the dash trim
bezel. Gently pull out on the trim bezel and
remove. Remove (4) hex-head screws from
the factory head unit and disconnect the
wiring.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Place the
gear selector in its lowest position. Unclip
the perimeter of the dash trim bezel.
Disconnect the rear a/c control harness and
the headlight switch from the back of the
dash trim bezel and remove the bezel.
Using a flat-blade screwdriver, press down
on the outside clips of the factory head unit
and remove.
Skip to the Installation
Instructions for ALL VEHICLES on Page #2.
PONTIAC Firebird 1993-02
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the radio trim bezel. Remove (4) 7mm hexhead screws securing the factory head unit
and disconnect the wiring.
28
2
Locate Bracket Set #9.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Locate Bracket Set #8.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
CHEVROLET Beretta / Corsica 1991-96
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Using a
panel removal tool, pry outward on the dash
trim bezel and remove. Remove (2) screws
securing the factory head unit and
disconnect the wiring.
2
Locate Bracket #7. Skip to the Installation
Instructions for ALL VEHICLES on Page
#34.
9
PONTIAC Bonneville 1987-93
CHEVROLET Blazer (full size) / Suburban 1989-91
GMC Jimmy (full size) / Suburban 1989-91
1
1
2
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws from the radio trim bezel and
remove the bezel. Remove (2) screws
securing the factory head unit and
disconnect the wiring.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Gently
unsnap and remove the dash trim bezel.
Remove the screws securing the factory
head unit and disconnect the wiring.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
CHEVROLET Blazer/S-10 Pickup · GMC Jimmy/Sonoma 1998-02
1
2
PONTIAC Bonneville 1994-99
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) 9/32" hex-head screws from the knee
bolster. Pull down on the bolster and
remove 9/32" screws exposed on the base
of the dash trim bezel. Remove (1) Phillips
screw above the instrument cluster. Unclip
the dash trim bezel and remove. Remove
(2) 9/32" hex-head screws securing the
factory head unit and disconnect the wiring.
Skip to the Installation Instructions for ALL
VEHICLES on Page #3.
10
2
Locate Bracket Set #10. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the right side of the dash trim bezel. Unclip
the left side of the bezel and remove.
Remove (3) 7mm hex-head screws securing
the factory head unit and disconnect the
wiring.
Locate Bracket Set #9.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
27
OLDSMOBILE Toronado 1982-85
1
CHEVROLET Camaro / PONTIAC Firebird 1982-84
2
1
2
"A"
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Depress
the clip located behind the headlight knob
and remove the knob. Remove (3) screws
securing the steering column trim and
remove. Remove (4) screws from the
bottom edge of the dash trim bezel and
remove.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
PONTIAC 6000 1982-91
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) star-drive screws from the dash trim
bezel and remove the bezel. Remove (4)
screws securing the factory head unit and
disconnect the wiring.
Cut and remove all mounting tabs on
Bracket #5 EXCEPT those tabs with holes
"A". The mounting tabs can be identified by
the stamped letter on the back of each tab.
Skip to the Installation Instructions for ALL
VEHICLES on Page #34.
CHEVROLET Camaro / PONTIAC Firebird 1985-92
2
1
2
"A"
"A"
"B"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Open
the glove box and remove (1) screw from the
side of the radio trim bezel. Gently remove
the bezel from the dash and the dummy
plate from the bezel.
26
Cut and remove all mounting tabs on
Bracket #5 EXCEPT tabs "A".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) star-drive screws from the dash trim
bezel and remove the bezel. Remove (4)
screws securing the factory head unit and
disconnect the wiring.
Cut and remove all mounting tabs on
Bracket #5 EXCEPT those tabs with holes
"B". The mounting tabs can be identified by
the stamped letter on the back of each tab.
Skip to the Installation Instructions for ALL
VEHICLES on Page #34.
11
CHEVROLET Camaro 1997-99
1
2
OLDSMOBILE Cutlass Supreme 1984-88
1
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the radio trim bezel and remove. Remove
(2) 7mm hex-head screws securing the
factory head unit and disconnect the wiring.
Locate Bracket Set #10. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the cigarette lighter and radio knobs and
unsnap the radio trim bezel. Remove (1)
screw from the right side of the ashtray
housing.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
CHEVROLET Caprice / Impala SS 1994-96
1
2
OLDSMOBILE Omega 1983-84
1
2
"C"
"C"
"C"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(5) hex-head screws from the ashtray cavity.
Remove (4) hex-head screws from the base
of the dash trim bezel. Unsnap the fuse box
cover and remove (1) hex-head screw
exposed. Remove (2) hex-head screws
above the instrument cluster. Place the gear
selector in "D1". Pull out on the cluster trim
and remove. Remove (1) hex-head screw
exposed on the left edge of the dash trim
bezel. Unclip the dash trim bezel (including
the radio trim bezel) and remove.
12
Locate Bracket Set #10. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
"C"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) hex-head washer screws from the
steering column trim panel, pull down on the
rear edge of the panel and remove. Remove
(4) Phillips screws from the top edge of the
dash trim bezel. Remove (2) hez-head
washer screws from the bottom of the dash
trim bezel and remove the bezel.
Cut and remove all mounting tabs on
Bracket #2 EXCEPT tabs "C".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
25
OLDSMOBILE Cutlass Calais 1984-91
1
2
CHEVROLET Cavalier 1982-90 / Cadillac Cimarron 1982-88
PONTIAC Sunbird J-2000 1982-88
1
2
"A"
"A"
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the console/glove box assembly and (3)
screws below the box. Lift up the parking
brake trim and remove (2) screws from the
gear shifter trim. Remove the ashtray from
the gear shifter area and (2) 7mm screws
exposed. Using a screwdriver, depress the
retainer tabs on the dash ashtray, pull the
ashtray out and remove (2) 7mm hex-head
screws from the ashtray bracket.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(6) star-drive screws from the dash trim
bezel and remove the bezel. Remove (2)
screws from the factory head unit and
disconnect the wiring.
CHEVROLET Cavalier 1991-94
OLDSMOBILE Cutlass Ciera 1982-96
1
2
Cut and remove all mounting tabs on
Bracket #4 EXCEPT tabs "A".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
1
2
"B"
"B"
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (2) screws from the ashtray
location. Remove (1) screw below and (2)
screws above the steering column. Pry the
a/c vents out and remove the screws
exposed in the vent cavities. Remove (6)
screws from the edge of the dash trim bezel
and remove the bezel.
24
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Using a
panel removal tool, carefully pry out on the
dash trim bezel and remove. Remove (2)
screws securing the factory head unit and
disconnect the wiring.
Cut and remove all mounting tabs on
Bracket #3 EXCEPT tabs "B".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
13
CHEVROLET Cavalier 1995-99
1
2
OLDSMOBILE 98 1984-90 / Delta 88 1986-88
1
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(3) 7mm hex-head screws from the top of the
glove box liner. Remove (2) 7mm hex-head
screws from the top-left corner of the glove
box cavity. Remove (1) Phillips screw from
the defroster duct. Remove the duct work
and (1) Phillips screw exposed. Unclip the
dash trim piece and remove (2) Phillips
screws exposed. Remove the dash pad and
(3) Phillips screws exposed at the top of the
radio trim bezel.
Locate Bracket Set #10. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Place
the gear shifter in low and remove the rubber
trim boot from the steering column. Remove
(2) Phillips screws from the radio trim bezel.
Unhook the ashtray/light wiring terminal and
remove the trim bezel.
OLDSMOBILE Achieva 1992-95
CHEVROLET Celebrity 1982-83
1
2
1
14
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the plastic plate next to each a/c vent and
remove (2) screws exposed. Remove (4)
screws surrounding the steering column.
Depress the light control knob spring,
remove the knob and lift the bezel off.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) screws from the top edge of the dash trim
bezel. Remove (2) screws from the bottom
edge of the bezel. Unsnap the a/c ducts,
disconnect the light switch and remove the
bezel.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
23
CHEVROLET Van (full size) 1988-95
GMC Van (full size) 1988-95
1
2
CHEVROLET Celebrity 1984-87
1
2
"C"
"C"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Carefully
unsnap the radio trim bezel and remove.
Remove (2) screws securing the factory
head unit and disconnect the wiring.
Cut and remove all mounting tabs on
Bracket #1 EXCEPT tabs "C".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the glove box compartment by depressing
the clip on the bottom of the glove box liner
and removing (6) nuts exposed above the
opening. Remove (6) Phillips screws below
the steering column. Remove the headlight
knob by depressing the clip on the back of
the knob and removing the nut. Remove the
cigarette lighter and disconnect the wiring.
Grasp the lighter socket, unscrew the brass
nut on the back of the lighter and remove the
socket. Remove the dash trim bezel and
disconnect the wiring.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
CHEVROLET Venture / OLDSMOBILE Silhouette 1997-99
PONTIAC Montana 1999 / TransSport 1997-98
1
CHEVROLET Citation II 1985
2
1
2
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (1) Phillips screw exposed in
the ashtray cavity. Remove (1) Phillips
screw from the cigarette lighter
compartment. Remove (2) Phillips screws
securing the factory head unit and
disconnect the wiring.
22
Locate Bracket Set #10. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws from the bottom steering column
trim panel and remove. Remove (6) screws
from the dash trim bezel, disconnect the
wiring and remove.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
15
CHEVROLET Corvette 1984-89
1
2
CHEVROLET S10 Pickup 1982-85 / S10 Blazer 1982-85
GMC S15 Pickup 1982-85 / S15 Jimmy 1982-85
1
2
"B"
"B"
(S10 APPLICATION
SHOWN AS EXAMPLE)
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(7) screws from the dash trim bezel. Move
the gear shifter to the lowest position. Pull
the right edge of the bezel forward, unhook
the left side and remove.
Remove the hardware securing the factory
mounting brackets to the factory head unit.
Remove and retain the brackets. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) star-drive screws from the corners of the
dash trim bezel. Remove (1) star-drive
screw from the lower-right corner of the
instrument cluster panel and remove the
dash trim bezel.
CHEVROLET Corvette 1997-02
1
Cut and remove all mounting tabs on
Bracket #1 EXCEPT tabs "C".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
CHEVROLET S10 Pickup 1986-93 / S10 Blazer 1986-94
GMC S15 Pickup 1986-93 / S15 Jimmy 1986-94
OLDSMOBILE Bravada 1991-94
2
1
2
"B"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Pry out on
the ride control switch and disconnect the
wiring. Unsnap the switch trim and remove
(2) 10mm hex-head bolts exposed. Open the
center console door, remove (4) screws from
the inner hinge and remove the door. Open
the ashtray and remove (1) screw exposed.
Remove the ashtray and (1) screw exposed.
Unclip the small grille to the left of the ignition
switch and remove (1) screw exposed. Unclip
the base of the radio trim bezel and remove.
16
Locate Bracket Set #10. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (1) screw inside the ashtray
cavity. Open the glove box and remove (2)
screws exposed on the edge of the dash trim
bezel.
Locate Bracket #(L) S-10 and the right
Bracket from Bracket Set #5. Cut and
remove all mounting tabs on the right
Bracket EXCEPT top tab "B".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
21
CHEVROLET Malibu 1997-99
1
CHEVROLET El Camino / Monte Carlo 1985-88
2
1
2
"C"
"C"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the radio trim bezel and remove. Remove
(2) 9/32" hex-head screws securing the
factory head unit and disconnect the wiring.
Locate Bracket Set #10. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) screws from the dash trim bezel.
Remove the bezel and disconnect the
cigarette lighter wiring.
CHEVROLET Nova 1985-88
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (2) screws from the ashtray
bracket. Remove (2) screws above the
radio opening and remove the radio trim
bezel.
20
2
Cut and remove all mounting tabs on
Bracket #2 EXCEPT tabs "C".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
CHEVROLET Express / GMC Savana 1996-00
"B"
Cut and remove all mounting tabs on
Bracket #1 EXCEPT tabs "B".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the plastic trim piece located below the
steering column. Unclip the dash trim bezel.
Pull the bezel over the steering column and
disconnect the wiring. Using a flat-blade
screwdriver, press down on the outside clips
of the factory head unit and remove. Skip to
the Installation Instructions for ALL
VEHICLES on Page #2.
2
Locate Bracket Set #8.
Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
17
CHEVROLET Lumina 1990-94
1
2
CHEVROLET Lumina APV / OLDSMOBILE Silhouette
PONTIAC TransSport 1990-95
1
"A"
2
"A"
"B"
"A"
"B"
"A"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws from the lower steering column
panel. Pull the panel down to access the
bottom portion of the radio trim bezel. Pull
the top and bottom edges of the bezel
forward and remove.
Cut and remove all mounting tabs on
Bracket #5 EXCEPT tabs "A".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws securing the lower steering
column panel and remove. Remove (2)
screws exposed on the left tab of the radio
trim bezel. Open the glove box and remove
(2) screws exposed on the right tabs of the
radio trim bezel.
CHEVROLET Lumina APV / OLDSMOBILE Silhouette
PONTIAC TransSport 1996
CHEVROLET Lumina / Monte Carlo 1995-99
1
2
Cut and remove all mounting tabs on
Bracket #6 EXCEPT tabs "B".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
1
2
"B"
"B"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the dash trim bezel and remove. (It may be
necessary to loosen the knee bolster).
Remove (2) 7mm hex-head screws securing
the factory head unit and disconnect the
wiring.
18
Locate Bracket Set #10. Skip to the
Installation Instructions for ALL VEHICLES
on Page #34.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(1) Phillips screw from each side of the
center console. Open the glove box and
remove (2) Phillips screws exposed.
Remove (2) 7mm hex-head screws and (1)
pop-clip from the lower steering column
panel, and (2) Phillips screws exposed near
the climate controls. Remove (1) 7mm hexhead screw under the glove box. Pull out on
the center console and remove.
Cut and remove all mounting tabs on
Bracket #6 EXCEPT tabs "B".
The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #34.
19