SRX110 Services Gateway Hardware Guide for H2
Model Numbers
Modified: 2016-08-22
Copyright © 2016, Juniper Networks, Inc.
Juniper Networks, Inc.
1133 Innovation Way
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
Copyright © 2016, Juniper Networks, Inc. All rights reserved.
Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United
States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other
trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Copyright © 2016, Juniper Networks, Inc.
All rights reserved.
The information in this document is current as of the date on the title page.
YEAR 2000 NOTICE
Juniper Networks hardware and software products are Year 2000 compliant. Junos OS has no known time-related limitations through the
year 2038. However, the NTP application is known to have some difficulty in the year 2036.
END USER LICENSE AGREEMENT
The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use with) Juniper Networks
software. Use of such software is subject to the terms and conditions of the End User License Agreement (“EULA”) posted at
http://www.juniper.net/support/eula.html. By downloading, installing or using such software, you agree to the terms and conditions of
that EULA.
ii
Copyright © 2016, Juniper Networks, Inc.
Table of Contents
About the Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Supported Platforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Documentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii
Requesting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii
Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . xviii
Opening a Case with JTAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii
Part 1
Overview
Chapter 1
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SRX110 Services Gateway Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SRX110 Services Gateway Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Accessing the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SRX110 Services Gateway Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SRX110 Services Gateway Integrated VDSL2 Interface Overview . . . . . . . . . . . . . . 6
SRX110 Services Gateway Integrated VDSL2 Interface Key Features . . . . . . . . . . . 6
SRX110 Services Gateway Integrated VDSL2 Interface Supported Profiles . . . . . . . 7
Chapter 2
Hardware Component Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SRX110 Services Gateway Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SRX110 Services Gateway 3G USB Modem Overview . . . . . . . . . . . . . . . . . . . . . . . 10
Introduction to the SRX110 Services Gateway 3G USB Modem . . . . . . . . . . . 10
SRX110 Services Gateway 3G USB Modem—Supported Modem Types . . . . . 10
Using the SRX110 Services Gateway 3G USB Modem . . . . . . . . . . . . . . . . . . . 10
SRX110 Services Gateway 3G USB Modem Key Features . . . . . . . . . . . . . . . . . . . . 12
Chapter 3
Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and
Integrated VDSL2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SRX110 Services Gateway Front Panel View with 3G and Integrated
VDSL2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SRX110 Services Gateway Back Panel View . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SRX110 Services Gateway Built-In Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SRX110 Services Gateway LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SRX110 Services Gateway Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SRX110 Services Gateway Ethernet Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . 21
SRX110 Services Gateway Integrated VDSL2 Interface LEDs . . . . . . . . . . . . . . . . . 22
Copyright © 2016, Juniper Networks, Inc.
iii
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
SRX110 Services Gateway Boot Devices and Dual-Root Partitioning Scheme . . . 22
Boot Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Dual-Root Partitioning Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Part 2
Site Planning and Specifications
Chapter 4
Planning and Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Site Preparation Checklist for the SRX110 Services Gateway . . . . . . . . . . . . . . . . . 27
General Site Guidelines for Installing the SRX110 Services Gateway . . . . . . . . . . . 30
SRX110 Services Gateway Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SRX110 Services Gateway 3G-WAN USB Port Physical Specifications . . . . . . . . . 32
SRX110 Services Gateway Cabinet Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 32
SRX110 Services Gateway Rack Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110
Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Chapter 5
Power Requirements and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SRX110 Services Gateway Site Electrical Wiring Guidelines . . . . . . . . . . . . . . . . . . 37
SRX110 Services Gateway Electrical and Power Requirements . . . . . . . . . . . . . . . 38
SRX110 Services Gateway Power Specifications and Requirements . . . . . . . . . . . 39
Chapter 6
Cable Specifications and Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Interface Cable and Wire Specifications for the SRX110 Services Gateway . . . . . . 41
RJ-45 Connector Pinouts for the SRX110 Services Gateway Ethernet Port . . . . . . 42
RJ-45 Connector Pinouts for the SRX110 Services Gateway Console Port . . . . . . 43
RJ-11 Connector Pinouts for the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . 44
Part 3
Initial Installation and Configuration
Chapter 7
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation Overview for the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . 47
Required Tools and Parts for Installing and Maintaining the SRX110 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SRX110 Services Gateway Autoinstallation Overview . . . . . . . . . . . . . . . . . . . . . . 49
Chapter 8
Unpacking the Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Unpacking the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Verifying Parts Received with the SRX110 Services Gateway . . . . . . . . . . . . . . . . . 51
Chapter 9
Installing the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Preparing the SRX110 Services Gateway for Rack-Mount Installation . . . . . . . . . . 55
Preparing the SRX110 Services Gateway for Desk-Mount Installation . . . . . . . . . 56
Preparing the SRX110 Services Gateway for Wall-Mount Installation . . . . . . . . . . 57
Chapter 10
Installing the Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Installing the SRX110 Services Gateway in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . 59
Adjusting the Power Supply Adapter Tray for the SRX110 Services Gateway for
Rack-Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Installing the SRX110 Services Gateway on a Desk . . . . . . . . . . . . . . . . . . . . . . . . . 63
iv
Copyright © 2016, Juniper Networks, Inc.
Table of Contents
Installing the SRX110 Services Gateway on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . 65
Installing a 3G USB Modem in the SRX110 Services Gateway USB Port . . . . . . . . 67
Connecting the 3G USB Modem on the USB Modem Extension
Cable-Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Installing a 3G USB Modem on the Rear Side of the SRX110 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Chapter 11
Grounding the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
SRX110 Services Gateway Grounding Specifications . . . . . . . . . . . . . . . . . . . . . . . . 71
Grounding the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Chapter 12
Connecting the SRX110 Services Gateway to External Devices . . . . . . . . . . 75
Connecting and Organizing the SRX110 Services Gateway Interface Cables . . . . . 75
Connecting the Modem at the SRX110 Services Gateway End . . . . . . . . . . . . . . . 76
Connecting the Modem to the Console Port on the SRX110 Services Gateway . . . 77
Connecting to the CLI at the User End for the SRX110 Services Gateway . . . . . . . 77
Chapter 13
Providing Power to the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . 79
Connecting the SRX110 Services Gateway to the Power Supply . . . . . . . . . . . . . . 79
Powering On the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Powering Off the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Chapter 14
Performing Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
SRX110 Services Gateway Software Configuration Overview . . . . . . . . . . . . . . . . 83
Preparing the SRX110 Services Gateway for Configuration . . . . . . . . . . . . . . . 83
Understanding Built-In Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Understanding Management Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Connecting the SRX110 Services Gateway to the J-Web Interface . . . . . . . . . . . . 86
SRX110 Services Gateway Secure Web Access Overview . . . . . . . . . . . . . . . . . . . . 87
Connecting the Services Gateway to the CLI Locally . . . . . . . . . . . . . . . . . . . . . . . 88
Viewing Factory-Default Settings of the SRX110 Services Gateway . . . . . . . . . . . 90
Performing Initial Software Configuration on the SRX110 Services Gateway Using
the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Performing Initial Software Configuration on the SRX110 Services Gateway Using
the Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
About the Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
About the Default Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
About the Guided Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Running the Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Configuring the 3G USB Modem on the SRX110 Services Gateway . . . . . . . . . . . 102
Configuring the Integrated VDSL2 Interface on the SRX110 Services Gateway . . 103
Part 4
Maintaining and Troubleshooting Components
Chapter 15
Maintaining Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Maintaining the SRX110 Services Gateway Hardware Components . . . . . . . . . . 107
Chapter 16
Troubleshooting Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Monitoring the SRX110 Services Gateway Chassis Using the CLI . . . . . . . . . . . . . 109
Monitoring the SRX110 Services Gateway Components Using LEDs . . . . . . . . . . 110
Monitoring the SRX110 Services Gateway Using Chassis Alarm Conditions . . . . . 112
Copyright © 2016, Juniper Networks, Inc.
v
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Monitoring the SRX110 Services Gateway Power System . . . . . . . . . . . . . . . . . . . 114
Resetting the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Using the Reset Config Button on the SRX110 Services Gateway . . . . . . . . . . . . . 115
Changing the Reset Config Button Behavior on the SRX110 Services Gateway . . 116
Juniper Networks Technical Assistance Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Part 5
Replacing Components
Chapter 17
Contacting Customer Support and Returning Components . . . . . . . . . . . . 121
Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Return Procedure for the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . 122
Locating the SRX110 Services Gateway Component Serial Number and Agency
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Listing the SRX110 Services Gateway and Component Details with the
CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
SRX110 Services Gateway Chassis Serial Number and Agency Labels . . . . . 123
Information You Might Need to Supply to Juniper Networks Technical Assistance
Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Packing the SRX110 Services Gateway and Components for Shipment . . . . . . . 125
Packing the Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Packing the Components for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Part 6
Safety and Regulatory Compliance Information
Chapter 18
General Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
SRX110 Services Gateway Definition of Safety Warning Levels . . . . . . . . . . . . . . 129
SRX110 Services Gateway General Safety Guidelines and Warnings . . . . . . . . . . 131
SRX110 Services Gateway Safety Requirements, Warnings, and Guidelines . . . . 135
Chapter 19
Fire Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
SRX110 Services Gateway Fire Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . 137
Chapter 20
Installation Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . 139
SRX110 Services Gateway Installation Safety Guidelines and Warnings . . . . . . . 139
Chapter 21
Laser and LED Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . . . 145
SRX110 Services Gateway Laser and LED Safety Guidelines and Warnings . . . . . 145
General Laser Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Class 1 Laser Product Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Class 1 LED Product Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Laser Beam Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Radiation from Open Port Apertures Warning . . . . . . . . . . . . . . . . . . . . . . . . 147
Chapter 22
Maintenance and Operational Safety Guidelines and Warnings . . . . . . . . 149
SRX110 Services Gateway Maintenance and Operational Safety Guidelines and
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Battery Handling Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Jewelry Removal Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Lightning Activity Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Operating Temperature Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
vi
Copyright © 2016, Juniper Networks, Inc.
Table of Contents
Product Disposal Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Chapter 23
Electrical Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
SRX110 Services Gateway Electrical Safety Guidelines and Warnings . . . . . . . . . 155
Electrical Safety Guidelines and Warnings In Case of Electrical Accident . . 155
General Electrical Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . 155
Chapter 24
Agency Approvals and Regulatory Compliance Information . . . . . . . . . . . . 157
SRX110 Services Gateway Agency Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
SRX110 Services Gateway Compliance Statements for EMC Requirements . . . . 158
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Korean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
SRX110 Services Gateway Compliance Statements for Environmental
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
SRX110 Services Gateway Compliance Statements for Acoustic Noise . . . . . . . 160
Part 7
Index
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Copyright © 2016, Juniper Networks, Inc.
vii
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
viii
Copyright © 2016, Juniper Networks, Inc.
List of Figures
Part 1
Overview
Chapter 2
Hardware Component Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 1: SRX110 Services Gateway — 12 V Power Supply . . . . . . . . . . . . . . . . . . . . . 9
Figure 2: 3G USB Modem with USB Protection Cover . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 3
Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 3: SRX110 Services Gateway Front Panel (SRX110H2-VA) . . . . . . . . . . . . . . 15
Figure 4: SRX110 Services Gateway Front Panel (SRX110H2-VB) . . . . . . . . . . . . . 16
Figure 5: SRX110 Services Gateway Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 6: SRX110 Services Gateway Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . 19
Figure 7: SRX110 Services Gateway Ethernet Port LEDs . . . . . . . . . . . . . . . . . . . . . 21
Part 2
Site Planning and Specifications
Chapter 4
Planning and Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 8: SRX110 Services Gateway with 3G and VDSL2 (VDSL/ADSL-POTS) . . 30
Figure 9: SRX110 Services Gateway with 3G and VDSL2 (VDSL/ADSL-ISDN) . . . . 31
Chapter 6
Cable Specifications and Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 10: Ethernet Cable Connector (RJ-45) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 11: Console Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Part 3
Initial Installation and Configuration
Chapter 10
Installing the Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 12: SRX110 Services Gateway Installation in a Rack — Positioning Mounting
Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 13: SRX110 Services Gateway Rack Installation — Securing Mounting
Brackets and Power Supply Adapter Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 14: SRX110 Services Gateway Rack Installation — Positioning Power Supply
Adapter Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 15: SRX110 Services Gateway Rack Installation — Hanging the Services
Gateway in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 16: Adjusting the Power Supply Adapter Tray to Accommodate the
60-Watt Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 17: SRX110 Services Gateway Desk Installation — Attaching the Vertical
Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 18: SRX110 Services Gateway Desk Installation — Placing the Services
Gateway on a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 19: SRX110 Services Gateway Wall Installation — Attaching the Mounting
Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Copyright © 2016, Juniper Networks, Inc.
ix
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Figure 20: SRX110 Services Gateway Wall Installation — Attaching the Mounting
Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Figure 21: 3G USB Modem with USB Protection Cover . . . . . . . . . . . . . . . . . . . . . . 67
Figure 22: Connecting the 3G USB modem to the SRX110 Services Gateway . . . . 68
Figure 23: 3G USB Modem Wall Installation—Attaching the USB Protection
Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Figure 24: 3G USB Modem Ceiling Installation—Attaching the USB Protection
Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Chapter 11
Grounding the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 25: Grounding the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . 72
Chapter 13
Providing Power to the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . 79
Figure 26: Connecting the SRX110 Services Gateway to the Power Supply . . . . . 80
Chapter 14
Performing Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Figure 27: Connecting to the Ethernet Port on an SRX110 Services Gateway . . . . 86
Figure 28: Connecting to the Console Port on an SRX110 Services Gateway . . . . 88
Part 5
Replacing Components
Chapter 17
Contacting Customer Support and Returning Components . . . . . . . . . . . . 121
Figure 29: Location of SRX110 Serial Number and Agency Labels . . . . . . . . . . . . 124
Part 6
Safety and Regulatory Compliance Information
Chapter 18
General Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Figure 30: Placing a Component into an Electrostatic Bag . . . . . . . . . . . . . . . . . . 134
x
Copyright © 2016, Juniper Networks, Inc.
List of Tables
About the Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Table 1: Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
Table 2: Text and Syntax Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
Part 1
Overview
Chapter 1
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table 3: SRX110 Services Gateway Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Table 4: SRX110 Services Gateway Hardware Features . . . . . . . . . . . . . . . . . . . . . . 5
Table 5: Profiles Supported on the Integrated VDSL2 Interface . . . . . . . . . . . . . . . . 7
Chapter 2
Hardware Component Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 6: Wireless USB Modems Supported by the SRX110 Services Gateway . . . 10
Table 7: 3G USB Modem with USB Protection Cover Components . . . . . . . . . . . . . 11
Chapter 3
Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 8: SRX110 Services Gateway Front Panel Components . . . . . . . . . . . . . . . . 16
Table 9: SRX110 Services Gateway Back Panel Components . . . . . . . . . . . . . . . . . 17
Table 10: SRX110 Services Gateway Built-In Hardware Interfaces . . . . . . . . . . . . . 18
Table 11: SRX110 Services Gateway Front Panel Components LEDs . . . . . . . . . . . 20
Table 12: SRX110 Services Gateway Built-In Ethernet Port LEDs . . . . . . . . . . . . . . . 21
Table 13: Integrated VDSL2 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Part 2
Site Planning and Specifications
Chapter 4
Planning and Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 14: Site Preparation Checklist for Services Gateway Installation . . . . . . . . . 27
Table 15: SRX110 Services Gateway Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 16: SRX110 Services Gateway 3G-WAN USB Port Physical
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 17: SRX110 Services Gateway Cabinet Requirements . . . . . . . . . . . . . . . . . . 32
Table 18: Rack Requirements for the Services Gateway . . . . . . . . . . . . . . . . . . . . . 34
Table 19: Clearance Requirements for the Services Gateway . . . . . . . . . . . . . . . . . 35
Chapter 5
Power Requirements and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 20: Site Electrical Wiring Guidelines for the Services Gateway . . . . . . . . . . 37
Table 21: Power Supply Electrical Specifications for the SRX110 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Chapter 6
Cable Specifications and Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 22: Cable and Wire Specifications for Ports . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Copyright © 2016, Juniper Networks, Inc.
xi
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 23: RJ-45 Connector Pinouts for the Services Gateway Ethernet Port
(10/100 Mbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 24: RJ-45 Connector Pinouts for the Services Gateway Ethernet Port (1
Gbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 25: RJ-45 Connector Pinouts for the Services Gateway Console Port . . . . . 43
Table 26: RJ-11 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Part 3
Initial Installation and Configuration
Chapter 7
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 27: Installation Procedure for the SRX110 Services Gateway . . . . . . . . . . . . 47
Table 28: Required Tools and Parts for Installing and Maintaining the SRX110
Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Chapter 8
Unpacking the Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 29: Parts List for a Fully Configured SRX110 Services Gateway . . . . . . . . . . 52
Table 30: Accessory Parts List for the SRX110 Services Gateway . . . . . . . . . . . . . 52
Chapter 9
Installing the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 31: SRX110 Services Gateway Preinstallation Checklist for Rack-Mount
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 32: SRX110 Services Gateway Preinstallation Checklist for Desk-Mount
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 33: SRX110 Services Gateway Preinstallation Checklist for Wall-Mount
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Chapter 10
Installing the Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 34: SRX Services Gateway Rack Installation Parts . . . . . . . . . . . . . . . . . . . 60
Table 35: SRX110 Services Gateway Wall Installation Parts . . . . . . . . . . . . . . . . . 65
Table 36: 3G USB Modem with USB Protection Cover Components . . . . . . . . . . . 67
Chapter 11
Grounding the SRX110 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Table 37: Grounding Cable Specifications for the Services Gateway . . . . . . . . . . . 71
Table 38: Grounding Cable Specifications for the Services Gateway . . . . . . . . . . . 72
Chapter 12
Connecting the SRX110 Services Gateway to External Devices . . . . . . . . . . 75
Table 39: Port Settings for Configuring the Modem on the Services Gateway
End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Table 40: Port Settings for Connecting to the CLI at User End . . . . . . . . . . . . . . . . 78
Chapter 14
Performing Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 41: Storage Media on the Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 42: Port Settings for Connecting to the Console Port . . . . . . . . . . . . . . . . . . 89
Table 43: SRX110 Services Gateway 3G USB Modem Basic CLI Commands . . . . 102
Part 4
Maintaining and Troubleshooting Components
Chapter 15
Maintaining Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Table 44: Maintenance Procedures for the Services Gateway Hardware
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Chapter 16
xii
Troubleshooting Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Copyright © 2016, Juniper Networks, Inc.
List of Tables
Table 45: Component LEDs on the Services Gateway . . . . . . . . . . . . . . . . . . . . . . 111
Table 46: SRX110 Services Gateway Chassis Alarm Conditions and Corrective
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Table 47: Services Gateway Power LED Status . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Part 5
Replacing Components
Chapter 17
Contacting Customer Support and Returning Components . . . . . . . . . . . . 121
Table 48: Return Procedure for SRX110 Services Gateway . . . . . . . . . . . . . . . . . . 122
Copyright © 2016, Juniper Networks, Inc.
xiii
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
xiv
Copyright © 2016, Juniper Networks, Inc.
About the Documentation
•
Documentation and Release Notes on page xv
•
Supported Platforms on page xv
•
Documentation Conventions on page xv
•
Documentation Feedback on page xvii
•
Requesting Technical Support on page xviii
Documentation and Release Notes
®
To obtain the most current version of all Juniper Networks technical documentation,
see the product documentation page on the Juniper Networks website at
http://www.juniper.net/techpubs/.
If the information in the latest release notes differs from the information in the
documentation, follow the product Release Notes.
Juniper Networks Books publishes books by Juniper Networks engineers and subject
matter experts. These books go beyond the technical documentation to explore the
nuances of network architecture, deployment, and administration. The current list can
be viewed at http://www.juniper.net/books.
Supported Platforms
For the features described in this document, the following platforms are supported:
•
SRX110
Documentation Conventions
Table 1 on page xvi defines notice icons used in this guide.
Copyright © 2016, Juniper Networks, Inc.
xv
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 1: Notice Icons
Icon
Meaning
Description
Informational note
Indicates important features or instructions.
Caution
Indicates a situation that might result in loss of data or hardware damage.
Warning
Alerts you to the risk of personal injury or death.
Laser warning
Alerts you to the risk of personal injury from a laser.
Tip
Indicates helpful information.
Best practice
Alerts you to a recommended use or implementation.
Table 2 on page xvi defines the text and syntax conventions used in this guide.
Table 2: Text and Syntax Conventions
Convention
Description
Examples
Bold text like this
Represents text that you type.
To enter configuration mode, type the
configure command:
user@host> configure
Fixed-width text like this
Italic text like this
Italic text like this
xvi
Represents output that appears on the
terminal screen.
user@host> show chassis alarms
•
Introduces or emphasizes important
new terms.
•
•
Identifies guide names.
A policy term is a named structure
that defines match conditions and
actions.
•
Identifies RFC and Internet draft titles.
•
Junos OS CLI User Guide
•
RFC 1997, BGP Communities Attribute
Represents variables (options for which
you substitute a value) in commands or
configuration statements.
No alarms currently active
Configure the machine’s domain name:
[edit]
root@# set system domain-name
domain-name
Copyright © 2016, Juniper Networks, Inc.
About the Documentation
Table 2: Text and Syntax Conventions (continued)
Convention
Description
Examples
Text like this
Represents names of configuration
statements, commands, files, and
directories; configuration hierarchy levels;
or labels on routing platform
components.
•
To configure a stub area, include the
stub statement at the [edit protocols
ospf area area-id] hierarchy level.
•
The console port is labeled CONSOLE.
< > (angle brackets)
Encloses optional keywords or variables.
stub <default-metric metric>;
| (pipe symbol)
Indicates a choice between the mutually
exclusive keywords or variables on either
side of the symbol. The set of choices is
often enclosed in parentheses for clarity.
broadcast | multicast
# (pound sign)
Indicates a comment specified on the
same line as the configuration statement
to which it applies.
rsvp { # Required for dynamic MPLS only
[ ] (square brackets)
Encloses a variable for which you can
substitute one or more values.
community name members [
community-ids ]
Indention and braces ( { } )
Identifies a level in the configuration
hierarchy.
; (semicolon)
Identifies a leaf statement at a
configuration hierarchy level.
(string1 | string2 | string3)
[edit]
routing-options {
static {
route default {
nexthop address;
retain;
}
}
}
GUI Conventions
Bold text like this
Represents graphical user interface (GUI)
items you click or select.
> (bold right angle bracket)
Separates levels in a hierarchy of menu
selections.
•
In the Logical Interfaces box, select
All Interfaces.
•
To cancel the configuration, click
Cancel.
In the configuration editor hierarchy,
select Protocols>Ospf.
Documentation Feedback
We encourage you to provide feedback, comments, and suggestions so that we can
improve the documentation. You can provide feedback by using either of the following
methods:
•
Online feedback rating system—On any page of the Juniper Networks TechLibrary site
at http://www.juniper.net/techpubs/index.html, simply click the stars to rate the content,
and use the pop-up form to provide us with information about your experience.
Alternately, you can use the online feedback form at
http://www.juniper.net/techpubs/feedback/.
Copyright © 2016, Juniper Networks, Inc.
xvii
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
E-mail—Send your comments to techpubs-comments@juniper.net. Include the document
or topic name, URL or page number, and software version (if applicable).
Requesting Technical Support
Technical product support is available through the Juniper Networks Technical Assistance
Center (JTAC). If you are a customer with an active J-Care or Partner Support Service
support contract, or are covered under warranty, and need post-sales technical support,
you can access our tools and resources online or open a case with JTAC.
•
JTAC policies—For a complete understanding of our JTAC procedures and policies,
review the JTAC User Guide located at
http://www.juniper.net/us/en/local/pdf/resource-guides/7100059-en.pdf.
•
Product warranties—For product warranty information, visit
http://www.juniper.net/support/warranty/.
•
JTAC hours of operation—The JTAC centers have resources available 24 hours a day,
7 days a week, 365 days a year.
Self-Help Online Tools and Resources
For quick and easy problem resolution, Juniper Networks has designed an online
self-service portal called the Customer Support Center (CSC) that provides you with the
following features:
•
Find CSC offerings: http://www.juniper.net/customers/support/
•
Search for known bugs: http://www2.juniper.net/kb/
•
Find product documentation: http://www.juniper.net/techpubs/
•
Find solutions and answer questions using our Knowledge Base: http://kb.juniper.net/
•
Download the latest versions of software and review release notes:
http://www.juniper.net/customers/csc/software/
•
Search technical bulletins for relevant hardware and software notifications:
http://kb.juniper.net/InfoCenter/
•
Join and participate in the Juniper Networks Community Forum:
http://www.juniper.net/company/communities/
•
Open a case online in the CSC Case Management tool: http://www.juniper.net/cm/
To verify service entitlement by product serial number, use our Serial Number Entitlement
(SNE) Tool: https://tools.juniper.net/SerialNumberEntitlementSearch/
Opening a Case with JTAC
You can open a case with JTAC on the Web or by telephone.
xviii
•
Use the Case Management tool in the CSC at http://www.juniper.net/cm/.
•
Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).
Copyright © 2016, Juniper Networks, Inc.
About the Documentation
For international or direct-dial options in countries without toll-free numbers, see
http://www.juniper.net/support/requesting-support.html.
Copyright © 2016, Juniper Networks, Inc.
xix
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
xx
Copyright © 2016, Juniper Networks, Inc.
PART 1
Overview
•
System Overview on page 3
•
Hardware Component Overview on page 9
•
Chassis Description on page 15
Copyright © 2016, Juniper Networks, Inc.
1
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
2
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 1
System Overview
•
SRX110 Services Gateway Description on page 3
•
SRX110 Services Gateway Hardware Features on page 4
•
SRX110 Services Gateway Integrated VDSL2 Interface Overview on page 6
•
SRX110 Services Gateway Integrated VDSL2 Interface Key Features on page 6
•
SRX110 Services Gateway Integrated VDSL2 Interface Supported Profiles on page 7
SRX110 Services Gateway Description
This topic includes the following sections:
•
About the SRX110 Services Gateway on page 3
•
SRX110 Services Gateway Models on page 4
•
Accessing the SRX110 Services Gateway on page 4
About the SRX110 Services Gateway
The Juniper Networks SRX110 Services Gateway offers complete functionality and
flexibility for delivering secure and reliable data along with multiple integrated interfaces
that support WAN and LAN connectivity. The SRX110 Services Gateway supports
interfaces such as 3G USB modem and integrated very-high-bit-rate digital subscriber
line version 2 (VDSL2).
The VDSL2 feature enables faster data transmission. VDSL lines connect service provider
networks and customer sites to provide high-bandwidth applications such as high-speed
Internet access, telephone services such as voice over IP (VoIP), high-definition TV
(HDTV), and interactive gaming services over a single connection. On the SRX Series
Services Gateway, the integrated VDSL2 interface provides ADSL backward compatibility.
The 3G USB modem enables wireless connectivity. The 3G-WAN USB port located at
the back panel of the device supports the external 3G USB modem using a Universal
Serial Bus (USB) modem extension cable.
The services gateway also provides security features such as IP Security (IPsec), virtual
private network (VPN), and firewall services for small and medium-sized companies and
enterprise branch and remote offices. Additional security features also include Unified
Threat Management (UTM), which consists of IPS antispam, antivirus, and Web filtering.
Copyright © 2016, Juniper Networks, Inc.
3
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
The SRX110 Services Gateway can be connected directly to traditional private networks
such as Multi Protocol Label Switching (MPLS) or to the public Internet.
The SRX110 Services Gateway runs the Junos operating system (Junos OS).
SRX110 Services Gateway Models
Table 3 on page 4 lists the SRX110 Services Gateway models with 2 GB memory. For
information on the models with 1 GB memory, see SRX110 Services Gateway Hardware
Guide for H Model Numbers.
Table 3: SRX110 Services Gateway Models
Model
Description
SRX110H2-VA
SRX110 Services Gateway with 8 Fast Ethernet ports, 2 GB DRAM,
2 GB CompactFlash memory, and 1 VDSL/ADSL-POTS port
SRX110H2-VB
SRX110 Services Gateway with 8 Fast Ethernet ports, 2 GB DRAM,
2 GB CompactFlash memory, and 1 VDSL/ADSL-ISDN port
Accessing the SRX110 Services Gateway
Two user interfaces are available for monitoring, configuring, troubleshooting, and
managing the SRX110 Services Gateway:
•
J-Web interface: Web-based graphical interface that allows you to operate a services
gateway without commands. The J-Web interface provides access to all Junos OS
functionality and features.
•
Junos OS command-line interface (CLI): Command shell that runs on top of a
UNIX-based operating system kernel. The CLI is a straightforward command interface.
On a single line, you type commands that are executed when you press the Enter key.
The CLI provides command Help and command completion.
For more details on the SRX110 Services Gateway software features and licenses, see
the following topics:
Related
Documentation
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
•
SRX110 Services Gateway Hardware Features on page 4
•
SRX110 Services Gateway Specifications on page 30
SRX110 Services Gateway Hardware Features
Table 4 on page 5 lists the hardware features supported on the SRX110 Services Gateway
models with 2 GB memory. For information on the models with 1 GB memory, see SRX110
Services Gateway Hardware Guide for H Model Numbers.
4
Copyright © 2016, Juniper Networks, Inc.
Chapter 1: System Overview
Table 4: SRX110 Services Gateway Hardware Features
Feature
Description
DDR Memory
2 GB
Power supply adapter
60 W (12 VDC and 5 A)
AC input voltage
100 to 240 VAC
AC input line frequency
50 to 60 Hz
AC adapter current rating
1.5 A maximum
Fast Ethernet ports
8
Console port
1
USB port
1
CompactFlash card
2 GB
LEDs
Status, Alarm, Power, and 3G
3G-WAN USB port (rear side)
•
For SRX110H2-VA—VDSL/ADSL-POTS (TX/RX
and SYNC)
•
For SRX110H2-VB—VDSL/ADSL-ISDN (TX/RX
and SYNC)
1
NOTE: If there is any problem with the CompactFlash card, you must return
the services gateway for repair or replacement. For this, you need to contact
Juniper Networks Technical Assistance Center (JTAC).
For more details on Junos OS features and licenses for the SRX110 Services Gateway,
see the following topics:
Related
Documentation
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
•
SRX110 Services Gateway Description on page 3
•
SRX110 Services Gateway Specifications on page 30
Copyright © 2016, Juniper Networks, Inc.
5
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
SRX110 Services Gateway Integrated VDSL2 Interface Overview
Very-high-bit-rate digital subscriber line (VDSL) technology is part of the xDSL family of
modem technologies. It provides fast data transmission over a single flat untwisted or
twisted pair of copper wires.
VDSL lines connect service provider networks and customer sites to provide
high-bandwidth applications (Triple Play services) such as high-speed Internet access,
telephone services such as voice over IP (VoIP), high-definition TV (HDTV), and interactive
gaming services over a single connection. VDSL2 is an enhancement to VDSL and permits
the transmission of asymmetric (half-duplex).
VDSL2 uses:
•
RJ-11 connector to connect to the VDSL/ADSL-POTS port.
•
RJ-45 connector to connect to the VDSL/ADSL-ISDN port.
The services gateway supports integrated VDSL2. The integrated VDSL2 carries the
Ethernet backplane. On the SRX Series Services Gateway, integrated VDSL2 provides
ADSL backward compatibility.
Integrated VDSL2 is compatible with the ITU-T G.993.2 (VDSL2) standard.
For more information, see the Interfaces for Security Devices.
Related
Documentation
•
SRX110 Services Gateway Integrated VDSL2 Interface Key Features on page 6
•
SRX110 Services Gateway Integrated VDSL2 Interface Supported Profiles on page 7
•
SRX110 Services Gateway Integrated VDSL2 Interface LEDs on page 22
•
Configuring the Integrated VDSL2 Interface on the SRX110 Services Gateway on page 103
SRX110 Services Gateway Integrated VDSL2 Interface Key Features
The following features are supported on integrated VDSL2:
6
•
ADSL/ADSL2/ADSL2+ backward compatibility with POTS supporting Annex-A
(Annex-M) and ISDN supporting Annex-B
•
Packet Mode Transfer (PTM) or Ethernet in the First Mile (EFM) (802.3ah)
•
Operation, Administration, and Maintenance (OAM) support for ADSL/ADSL2/ADSL2+
mode
•
Asynchronous Transfer Mode (ATM) quality of service (QoS) (supported only when
the VDSL2 interface is operating in ADSL2 mode)
•
Multilink Point-to-Point Protocol (MLPPP) (supported only when the VDSL2 interface
is operating in ADSL2 mode)
Copyright © 2016, Juniper Networks, Inc.
Chapter 1: System Overview
Related
Documentation
•
Support for a maximum of 10 permanent virtual connections (PVCs) (only in
ADSL/ADSL2/ADSL2+ mode)
•
Dying Gasp support (ADSL/ADSL2/ADSL2+ and VDSL2 modes)
•
SRX110 Services Gateway Integrated VDSL2 Interface Overview on page 6
•
SRX110 Services Gateway Integrated VDSL2 Interface LEDs on page 22
•
Configuring the Integrated VDSL2 Interface on the SRX110 Services Gateway on page 103
SRX110 Services Gateway Integrated VDSL2 Interface Supported Profiles
A profile is a table that contains a list of preconfigured VDSL2 settings. Table 5 on page 7
lists the different profiles supported on integrated VDSL2, along with their data rates.
Table 5: Profiles Supported on the Integrated VDSL2 Interface
Related
Documentation
Profile
Data Rate (Mbps)
8a
50
8b
50
8c
50
8d
50
12a
68
12b
68
17a
100
Auto
Auto-negotiated (based on profile)
•
SRX110 Services Gateway Integrated VDSL2 Interface Overview on page 6
•
SRX110 Services Gateway Integrated VDSL2 Interface LEDs on page 22
•
Configuring the Integrated VDSL2 Interface on the SRX110 Services Gateway on page 103
Copyright © 2016, Juniper Networks, Inc.
7
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
8
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 2
Hardware Component Overview
•
SRX110 Services Gateway Power Supply on page 9
•
SRX110 Services Gateway 3G USB Modem Overview on page 10
•
SRX110 Services Gateway 3G USB Modem Key Features on page 12
SRX110 Services Gateway Power Supply
The power supply for the SRX110 Services Gateway is external. You must use the power
supply adapter provided by Juniper Networks to provide power to the services gateway.
Figure 1 on page 9 shows the label for the 12 V power supply.
g033607
Figure 1: SRX110 Services Gateway — 12 V Power Supply
Related
Documentation
•
Monitoring the SRX110 Services Gateway Power System on page 114
•
Powering On the SRX110 Services Gateway on page 80
•
Powering Off the SRX110 Services Gateway on page 81
Copyright © 2016, Juniper Networks, Inc.
9
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
SRX110 Services Gateway 3G USB Modem Overview
This topic includes the following sections:
•
Introduction to the SRX110 Services Gateway 3G USB Modem on page 10
•
SRX110 Services Gateway 3G USB Modem—Supported Modem Types on page 10
•
Using the SRX110 Services Gateway 3G USB Modem on page 10
Introduction to the SRX110 Services Gateway 3G USB Modem
Wireless WAN access is becoming widely available and comparably priced with Integrated
Services Digital Network (ISDN) and Digital Subscriber Line (DSL). The SRX110 Services
Gateway supports a wireless interface as a backup for primary interfaces such as Fast
Ethernet.
To facilitate wireless connectivity, the device has a 3G-WAN USB port on the back panel
that supports the external 3G USB modem using a USB modem extension cable. For
more information on the back panel of the device, see SRX110 Services Gateway Front
Panel and Back Panel Views with 3G and Integrated VDSL2.
SRX110 Services Gateway 3G USB Modem—Supported Modem Types
Table 6 on page 10 lists the wireless modems supported on the SRX110 Services Gateway.
Table 6: Wireless USB Modems Supported by the SRX110 Services
Gateway
Wireless USB Modem
Release Supported
Sierra Wireless Compass 888. Not available from
Juniper Networks.
Junos OS Release 11.2 R3 and later.
Sierra Wireless AirCard 319U. Not available from
Juniper Networks.
Junos OS Release 11.2 R3 and later.
Using the SRX110 Services Gateway 3G USB Modem
To use the 3G USB modem, you plug one end of the USB modem extension cable into
the 3G-WAN USB port on the rear side of the device, and then plug the 3G USB modem
into the USB modem extension cable-mount slot. This enables you to dial a wireless call
to the 3G wireless service provider network, which acts as an Internet gateway. To use
the 3G USB modem as a backup interface, you can use the dialer feature available in the
services gateway. The 3G USB modem is secured with a USB protection cover as shown
in Figure 2 on page 11.
10
Copyright © 2016, Juniper Networks, Inc.
Chapter 2: Hardware Component Overview
g033622
Figure 2: 3G USB Modem with USB Protection Cover
Table 7 on page 11 lists the components of the 3G USB modem with USB protection
cover.
Table 7: 3G USB Modem with USB Protection Cover Components
Related
Documentation
Number
Component
1
USB mount top cover
2
USB modem
3
USB mount (magnetic/non-magnetic)
4
USB mount base
5
Lock
•
Installing a 3G USB Modem in the SRX110 Services Gateway USB Port on page 67
•
SRX110 Services Gateway 3G-WAN USB Port Physical Specifications on page 32
•
Configuring the 3G USB Modem on the SRX110 Services Gateway on page 102
Copyright © 2016, Juniper Networks, Inc.
11
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
SRX110 Services Gateway 3G USB Modem Key Features
The 3G USB modem provides the following key features:
•
Onboard Subscriber Identity Module (SIM)—All GSM cards have an onboard SIM. The
service provider populates this SIM with the subscriber service parameters.
•
Unlocking support—You can unlock GSM USB modems from the Junos OS CLI. If the
SIM is locked, you need to unlock it before making a call.
NOTE: Only GSM cards support locking and unlocking of the SIM.
•
Interface support—The 3G USB modem interface supports the IP-over-PPP interface
from the network through the wireless link.
•
Dial-out support—The dialer interface can place calls and has multiple features such
as dial-backup, dialer-watchlist, and dialer-filter. The dialer interface can use the 3G
USB modem to support the dial-out feature.
NOTE: The 3G USB modem does not support the dial-in feature.
•
12
Card information availability—You can use CLI commands to obtain information about
a 3G USB modem, such as type, version, wireless status, and user profiles.
Copyright © 2016, Juniper Networks, Inc.
Chapter 2: Hardware Component Overview
•
Security:
•
PIN lock support—GSM cards support PIN lock, which prevents unauthorized access
and use of the wireless account.
•
SIM card lock/unlock—You can use CLI request commands to lock or unlock the SIM
card.
•
PIN code storage option—You can store the PIN code you provide in the services
gateway configuration so that the SIM can be unlocked without the need for user
intervention every time the device is rebooted or reset.
NOTE: Currently, all GSM cards support PIN-protected SIMs.
Related
Documentation
•
SRX110 Services Gateway 3G USB Modem Overview on page 10
•
Installing a 3G USB Modem in the SRX110 Services Gateway USB Port on page 67
•
SRX110 Services Gateway 3G-WAN USB Port Physical Specifications on page 32
Copyright © 2016, Juniper Networks, Inc.
13
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
14
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 3
Chassis Description
•
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2 on page 15
•
SRX110 Services Gateway Built-In Interfaces on page 17
•
SRX110 Services Gateway LEDs on page 19
•
SRX110 Services Gateway Integrated VDSL2 Interface LEDs on page 22
•
SRX110 Services Gateway Boot Devices and Dual-Root Partitioning Scheme on page 22
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2
This topic includes the following sections:
•
SRX110 Services Gateway Front Panel View with 3G and Integrated VDSL2 on page 15
•
SRX110 Services Gateway Back Panel View on page 16
SRX110 Services Gateway Front Panel View with 3G and Integrated VDSL2
Figure 3 on page 15 and Figure 4 on page 16 show the front panels of the SRX110 Services
Gateway models SRX110H2-VA and SRX110H2-VB.
g033602
Figure 3: SRX110 Services Gateway Front Panel (SRX110H2-VA)
1
Copyright © 2016, Juniper Networks, Inc.
2
3
4
5
6
7
8
15
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
g033604
Figure 4: SRX110 Services Gateway Front Panel (SRX110H2-VB)
1
2
4
3
5
6
7
8
Table 8 on page 16 lists the front panel components of the SRX110 Services Gateway.
Table 8: SRX110 Services Gateway Front Panel Components
Number
Component
1
Power button
2
LEDs: Alarm, Status, Power, and 3G
3
USB port
4
Fast Ethernet ports
5
Console port
6
Reset Config button
7
LEDs: SYNC and TX/RX
8
•
For SRX110H2-VA—VDSL/ADSL-POTS
•
For SRX110H2-VB—VDSL/ADSL-ISDN
For more information on the front panel components, see the following topics:
•
SRX110 Services Gateway Built-In Interfaces on page 17
•
SRX110 Services Gateway LEDs on page 19
•
SRX110 Services Gateway Boot Devices and Dual-Root Partitioning Scheme on page 22
SRX110 Services Gateway Back Panel View
Figure 5 on page 16 shows the back panel of the SRX110 Services Gateway.
Figure 5: SRX110 Services Gateway Back Panel
2
3
4
5
6
7
g033603
1
16
Copyright © 2016, Juniper Networks, Inc.
Chapter 3: Chassis Description
Table 9 on page 17 lists the back panel components of the SRX110 Services Gateway.
Table 9: SRX110 Services Gateway Back Panel Components
Number
Component
1
Cable tie holder
2
3G-WAN USB port
3
Lock
4
Grounding point
5
CompactFlash card
6
Power supply unit
7
Cable tie holder
NOTE:
Related
Documentation
•
If there is any problem with the CompactFlash card, you must return the
services gateway for repair or replacement. For this, you need to contact
Juniper Networks Technical Assistance Center (JTAC).
•
The cable tie holder provides support for holding the power cord to the
power supply point.
•
The lock allows you to lock and secure the device to the installation site.
•
SRX110 Services Gateway Specifications on page 30
•
SRX110 Services Gateway Built-In Interfaces on page 17
•
SRX110 Services Gateway LEDs on page 19
•
SRX110 Services Gateway Power Supply on page 9
SRX110 Services Gateway Built-In Interfaces
Table 10 on page 18 summarizes the interface ports supported on the SRX110 Services
Gateway.
Copyright © 2016, Juniper Networks, Inc.
17
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 10: SRX110 Services Gateway Built-In Hardware Interfaces
Interface
Specification
Description
Fast Ethernet
The Fast Ethernet ports:
The Fast Ethernet ports can be
used:
Universal Serial Bus (USB)
•
Consist of eight fixed ports
•
Are labeled as port 0/0 to
port 0/7 on the front panel
•
•
Provide link speeds of
10/100 Mbps
To provide LAN connectivity
to hubs, switches, local
servers, and workstations.
•
•
Operate in full-duplex and
half-duplex modes
To forward incoming data
packets to the device.
•
•
Support flow control
To receive outgoing data
packets from the device.
•
Support autonegotiation
•
Support autosensing
The USB port:
The USB port can be used:
•
Consists of one port
•
•
Supports the following
modes:
•
•
Full-speed
•
High-speed
Complies with USB revision
2.0
To support a USB storage
device that functions as a
secondary boot device in
case of internal flash
memory device failure on
startup (if the USB storage
device is installed and
configured).
NOTE: You must install and
configure the USB storage
device on the USB port to
use it as a secondary boot
device. Additionally, the USB
device must have Junos OS
installed.
•
Console
18
To provide the USB
interfaces that are used to
communicate with many
types of USB storage
devices supported by Juniper
Networks.
The console port:
The console port can be used:
•
Consists of one port
•
•
Uses an RJ-45 serial cable
connector
To provide the console
interface.
•
•
Supports the RS-232
(EIA-232) standard
To function as a
management port for
logging in to a device
directly.
•
To configure the device
using the CLI.
Copyright © 2016, Juniper Networks, Inc.
Chapter 3: Chassis Description
Table 10: SRX110 Services Gateway Built-In Hardware
Interfaces (continued)
Interface
Specification
Description
Integrated VDSL2 interface
The VDSL2 port:
The VDSL2 port can be used to
provide LAN and WAN
functionality, along with
connectivity to various media
types.
3G USB modem
Related
Documentation
•
Consists of one port
•
Uses an RJ-11 connector for
VDSL/ADSL-POTS
•
Uses an RJ-45 connector for
VDSL/ADSL-ISDN
The 3G-WAN USB port on the
rear side uses a USB modem
extension cable to support the
external 3G USB modem.
The 3G USB modem provides
wireless connectivity.
•
SRX110 Services Gateway Specifications on page 30
•
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2 on page 15
•
SRX110 Services Gateway LEDs on page 19
SRX110 Services Gateway LEDs
This topic includes the following sections:
•
SRX110 Services Gateway Front Panel LEDs on page 19
•
SRX110 Services Gateway Ethernet Port LEDs on page 21
SRX110 Services Gateway Front Panel LEDs
Figure 6 on page 19 shows the SRX110 Services Gateway Front Panel LEDs.
g033605
Figure 6: SRX110 Services Gateway Front Panel LEDs
Table 11 on page 20 lists the LED indicators on the SRX110 Services Gateway front panel.
Copyright © 2016, Juniper Networks, Inc.
19
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 11: SRX110 Services Gateway Front Panel Components LEDs
Component
Description
Usage
Alarm LED
The Alarm LED has the following indicator colors:
The Alarm LED can be used
to gather information on
critical, major, or minor
alarms or to determine if the
device is functioning
normally.
•
Solid red indicates a critical alarm.
•
Solid amber indicates a major alarm.
•
Green indicates that the device is functioning
normally with no alarms.
•
Off indicates that the device is not powered on.
NOTE: When the system is up and running, if
the Alarm LED is off, it indicates that no alarms
are present on the device.
Status LED
Power LED
3G LED
20
The Status LED has the following indicator colors:
•
Solid green indicates that the device is
functioning normally.
•
Solid amber indicates that the device is starting
up.
•
Solid red indicates that the device has failed.
•
Off indicates that the device is not powered on.
The Power LED has the following indicator colors:
•
Solid green indicates that the device is
functioning normally.
•
Solid amber indicates that the Power button
has been pressed and quickly released. The
device is gracefully shutting down.
•
Solid red indicates that there is a problem with
the power supply.
•
Off indicates that the device is not receiving
power.
The 3G LED has the following indicator colors:
•
Solid green indicates that the 3G USB modem
is functioning normally or connected to network.
•
Solid red indicates that the 3G USB modem is
not registered with network.
•
Solid amber indicates that the 3G USB modem
is registered with network.
•
Off indicates that the 3G USB modem is not
detected.
The Status LED can be used
to determine whether the
device is starting up, is
functioning normally, or has
failed.
The Power LED can be used
to determine if the device is
receiving power.
The 3G LED can be used to
determine if the 3G USB
modem is plugged in.
NOTE: The 3G LED will be
functional only if you reboot
the services gateway after
plugging in the modem.
Copyright © 2016, Juniper Networks, Inc.
Chapter 3: Chassis Description
Table 11: SRX110 Services Gateway Front Panel Components
LEDs (continued)
Component
Description
Usage
SYNC LED
The SYNC LED for the VDSL2 interface has the
following indicator colors:
The SYNC LED can be used
to determine if the VDSL2
link is connected.
•
Solid green indicates that the VDSL2 link is up.
•
Blinking green indicates that the VDSL2 link is
in training and there is no connection to CO.
NOTE: Training refers to the negotiation of the
best mode for a DSL connection.
•
TX/RX LED
Off indicates that interface has not yet booted
up.
The TX/RX LED for the VDSL2 interface has the
following indicator colors:
•
Blinking green indicates that there is traffic.
•
Solid green indicates an invalid state.
•
Off indicates that there is no traffic.
The TX/RX LED can be used
to determine if there is any
traffic through the VDSL
interface.
SRX110 Services Gateway Ethernet Port LEDs
On the device, each Fast Ethernet port has two LEDs. Figure 7 on page 21 shows the
device Ethernet port LEDs.
Figure 7: SRX110 Services Gateway Ethernet Port LEDs
Table 12 on page 21 describes the built-in Ethernet port LEDs.
Table 12: SRX110 Services Gateway Built-In Ethernet Port LEDs
Number
Function
Color
State
Description
1
LINK/ACTIVE
LED
Green
On, blinking
Link is active. Data
communication is taking place.
On, not
blinking
Link is active. No data
communication is taking place.
Off
Link is inactive.
NOTE: The LED marked as 2 in Figure 7 on page 21 is not functional in this
release.
Copyright © 2016, Juniper Networks, Inc.
21
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Related
Documentation
•
SRX110 Services Gateway Specifications on page 30
•
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2 on page 15
•
SRX110 Services Gateway Boot Devices and Dual-Root Partitioning Scheme on page 22
SRX110 Services Gateway Integrated VDSL2 Interface LEDs
The integrated VDSL2 interface has two LEDs. Table 13 on page 22 describes the LED
states.
Table 13: Integrated VDSL2 LEDs
LED
Color
State
Description
SYNC
Green
On
Indicates that the VDSL2 interface link is up.
Blinking
Indicates training is in progress and there is
no connection to CO.
NOTE: Training refers to the negotiation of
the best mode for a DSL connection.
TX/RX
Related
Documentation
Green
Off
Indicates that interface has not yet booted
up.
Blinking
Indicates that traffic is passing through.
On
Indicates that it is an invalid state.
Off
Indicates that no traffic is passing through.
•
SRX110 Services Gateway Integrated VDSL2 Interface Overview on page 6
•
Configuring the Integrated VDSL2 Interface on the SRX110 Services Gateway on page 103
SRX110 Services Gateway Boot Devices and Dual-Root Partitioning Scheme
This topic includes the following sections:
•
Boot Devices on page 22
•
Dual-Root Partitioning Scheme on page 23
Boot Devices
The SRX110 Services Gateway can boot from two devices:
22
•
CompactFlash (default; always present)
•
USB storage key (alternate)
Copyright © 2016, Juniper Networks, Inc.
Chapter 3: Chassis Description
Dual-Root Partitioning Scheme
Dual-root partitions allow services gateways to remain functional if the file system
becomes corrupted, and they facilitate easy recovery of the corrupted file system.
The dual-root partitioning scheme keeps the primary and backup Junos OS images in
two independently bootable root partitions. If the primary root partition becomes
corrupted, the system can boot from the backup Junos OS image in the other root partition
and remain fully functional.
When the SRX110 Services Gateway powers up, it tries to boot Junos OS from the default
storage medium. If the device fails to boot from the default storage medium, it tries to
boot from the alternate storage medium. With the dual-root partitioning scheme, the
services gateway first tries to boot Junos OS from the primary root partition and then
from the backup root partition on the default storage medium. If both primary and backup
root partitions of a storage medium fail to boot, then the device tries to boot from the
next available type of storage media. The services gateway remains fully functional even
if it boots Junos OS from the backup root partition of the storage medium.
Related
Documentation
•
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2 on page 15
•
SRX110 Services Gateway LEDs on page 19
•
SRX110 Services Gateway Power Supply on page 9
•
SRX110 Services Gateway Specifications on page 30
Copyright © 2016, Juniper Networks, Inc.
23
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
24
Copyright © 2016, Juniper Networks, Inc.
PART 2
Site Planning and Specifications
•
Planning and Preparing the Site on page 27
•
Power Requirements and Specifications on page 37
•
Cable Specifications and Pinouts on page 41
Copyright © 2016, Juniper Networks, Inc.
25
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
26
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 4
Planning and Preparing the Site
•
Site Preparation Checklist for the SRX110 Services Gateway on page 27
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
SRX110 Services Gateway Specifications on page 30
•
SRX110 Services Gateway 3G-WAN USB Port Physical Specifications on page 32
•
SRX110 Services Gateway Cabinet Requirements on page 32
•
SRX110 Services Gateway Rack Requirements on page 33
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
Site Preparation Checklist for the SRX110 Services Gateway
The checklist in Table 14 on page 27 summarizes the tasks you need to perform when
preparing a site for installing the services gateway.
Table 14: Site Preparation Checklist for Services Gateway Installation
Item or Task
Additional
Information
Performed By
Date
Notes
Environment
Verify that the
environmental factors
such as temperature
and humidity do not
exceed device
tolerances.
“SRX110
Services
Gateway
Specifications”
on page 30
Power
Copyright © 2016, Juniper Networks, Inc.
27
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 14: Site Preparation Checklist for Services Gateway
Installation (continued)
Item or Task
•
Measure the distance
between the external
power sources and
the device installation
site.
•
Locate sites for
connection of system
grounding.
•
Calculate the power
consumption and
requirements.
Additional
Information
Performed By
Date
Notes
“SRX110
Services
Gateway Site
Electrical Wiring
Guidelines” on
page 37
“SRX110
Services
Gateway Power
Specifications
and
Requirements”
on page 39
Rack Requirements
Verify that your rack
meets the minimum
requirements.
“SRX110
Services
Gateway Rack
Requirements”
on page 33
Rack Installation
•
Plan the rack location,
including the required
space clearances.
•
Secure the rack to the
floor and the building
structure.
“Preparing the
SRX110 Services
Gateway for
Rack-Mount
Installation” on
page 55
Cabinet Requirements
•
Verify that your
cabinet meets the
minimum
requirements.
•
Plan the cabinet
location, including the
required space
clearances.
“SRX110
Services
Gateway
Cabinet
Requirements”
on page 32
Wall Installation
28
Copyright © 2016, Juniper Networks, Inc.
Chapter 4: Planning and Preparing the Site
Table 14: Site Preparation Checklist for Services Gateway
Installation (continued)
Item or Task
•
Verify that the area
selected meets the
minimum
requirements.
•
Verify that you have
the required hardware
for proceeding with
the installation.
Additional
Information
Performed By
Date
Notes
“Preparing the
SRX110 Services
Gateway for
Wall-Mount
Installation” on
page 57
Desktop Installation
•
Verify that the area
selected meets the
minimum
requirements.
•
Plan the installation
location, including
required space
clearances and
airflow requirements.
“Preparing the
SRX110 Services
Gateway for
Desk-Mount
Installation” on
page 56
Cables
Related
Documentation
•
Acquire cables and
connectors.
•
Review the maximum
distance allowed for
each cable. Choose
the length of cable
based on the distance
between the
hardware
components being
connected.
•
Plan the cable routing
and management.
“Interface Cable
and Wire
Specifications
for the SRX110
Services
Gateway” on
page 41
•
Installation Overview for the SRX110 Services Gateway on page 47
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
SRX110 Services Gateway Cabinet Requirements on page 32
•
SRX110 Services Gateway Rack Requirements on page 33
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
Copyright © 2016, Juniper Networks, Inc.
29
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
General Site Guidelines for Installing the SRX110 Services Gateway
The following precautions help you plan an acceptable operating environment for your
services gateway and avoid environmentally caused equipment failures:
•
The SRX110 Services Gateway requires unrestricted circulation of air to maintain an
optimal operating temperature. Allow sufficient clearance between the front and back
of the chassis and adjacent equipment. Ensure that there is adequate circulation in
the installation location.
•
Follow the electrostatic discharge (ESD) procedures to avoid damaging the equipment.
Static discharge can cause components to fail completely or intermittently over time.
NOTE: Install the device only in restricted areas, such as dedicated equipment
rooms and equipment closets, in accordance with Articles 110–16, 110–17,
and 110–18 of the National Electrical Code, ANSI/NFPA 70.
Related
Documentation
•
SRX110 Services Gateway General Safety Guidelines and Warnings on page 131
•
SRX110 Services Gateway Rack Requirements on page 33
•
SRX110 Services Gateway Cabinet Requirements on page 32
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
SRX110 Services Gateway Specifications
The SRX110 Services Gateway chassis is a rigid sheet metal structure of 1 rack unit (U)
height, which houses all the other hardware components.
Figure 8 on page 30 shows the SRX110 Services Gateway with 3G and VDSL2
(VDSL/ADSL-POTS).
g033600
Figure 8: SRX110 Services Gateway with 3G and VDSL2
(VDSL/ADSL-POTS)
30
Copyright © 2016, Juniper Networks, Inc.
Chapter 4: Planning and Preparing the Site
Figure 9 on page 31 shows the SRX110 Services Gateway with 3G and VDSL2
(VDSL/ADSL-ISDN).
g033601
Figure 9: SRX110 Services Gateway with 3G and VDSL2
(VDSL/ADSL-ISDN)
Table 15 on page 31 provides information on the physical specifications of the SRX110
Services Gateway.
Table 15: SRX110 Services Gateway Specifications
Specification
Value
Chassis height
1.7 in. (4.4 cm)
Chassis width
11 in. (28 cm)
Chassis depth
8.4 in. (21.3 cm)
Chassis weight
4.3 lb (1.962 kg)
Average power consumption
24 W
Altitude
No performance degradation to 10,000 ft (3048 m)
Relative humidity
5% to 90%, noncondensing
Temperature
Normal operation ensured in temperature range of 32°
F (0° C) to 104° F (+40° C)
Nonoperating storage temperature in shipping container:
–40° F (–40° C) to 158° F (70° C)
Related
Documentation
•
Maximum thermal output
99 BTU/hour
Noise level
< 15 dB(A) or less per EN ISO 7779
SRX110 Services Gateway Description on page 3
Copyright © 2016, Juniper Networks, Inc.
31
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2 on page 15
•
Monitoring the SRX110 Services Gateway Components Using LEDs on page 110
•
SRX110 Services Gateway Electrical Safety Guidelines and Warnings on page 155
SRX110 Services Gateway 3G-WAN USB Port Physical Specifications
Table 16 on page 32 lists the physical specifications of the SRX110 Services Gateway
3G-WAN USB port.
Table 16: SRX110 Services Gateway 3G-WAN USB Port Physical
Specifications
Related
Documentation
Specification
Value
Voltage supply
5V
Current rating
0.5 A
Maximum power consumption
2.5 W
•
Configuring the 3G USB Modem on the SRX110 Services Gateway on page 102
•
Installing a 3G USB Modem in the SRX110 Services Gateway USB Port on page 67
SRX110 Services Gateway Cabinet Requirements
The services gateway can be installed in a standard 31.5-in. (80.0-cm) or larger enclosed
cabinet.
Table 17 on page 32 provides the details on cabinet size, clearance, and airflow
requirements.
Table 17: SRX110 Services Gateway Cabinet Requirements
Cabinet Requirement
Specifications
Size
19 in. (48.3 cm) as defined in Cabinets, Racks, Panels, and
Associated Equipment (document number EIA-310–D)
published by the Electronics Industry Association
(http://www.eia.org).
You can mount the services gateway horizontally in the
cabinet.
32
Copyright © 2016, Juniper Networks, Inc.
Chapter 4: Planning and Preparing the Site
Table 17: SRX110 Services Gateway Cabinet Requirements (continued)
Cabinet Requirement
Specifications
Clearance
•
The cabinet is at least 1 U (1.75 in. or 4.5 cm) high.
•
The outer edges of the mounting brackets extend the width
of either chassis to 19 in. (48.2 cm), and the front of the
chassis extends approximately 0.5 in. (1.27 cm) beyond the
mounting brackets.
•
The minimum total clearance inside the cabinet is 30.7 in.
(78 cm) between the inside of the front door and the inside
of the rear door.
NOTE: The holes for the mounting brackets for the chassis
are spaced 1.25 in. (3.2 cm) apart, measured from the center
of the hole.
Airflow
•
Ensure that ventilation through the cabinet is sufficient to
prevent overheating.
•
Ensure that cool air supply is adequate to dissipate the
thermal output of the device.
•
Install the device as close as possible to the front of the
cabinet so that the cable management system clears the
inside of the front door. Installing the chassis close to the
front of the cabinet maximizes the clearance at the rear of
the cabinet for critical airflow.
•
Route and dress all cables to minimize the blockage of
airflow to and from the chassis.
NOTE: A cabinet larger than the minimum required size
provides better airflow and reduces the chance of overheating.
Related
Documentation
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
SRX110 Services Gateway Rack Requirements on page 33
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
SRX110 Services Gateway Rack Requirements
The services gateway can be installed in a rack. Many types of racks are acceptable,
including front-mount racks and four-post (telco) racks.
NOTE: The services gateway cannot be center mounted in a rack.
Table 18 on page 34 provides the details of requirements for rack size, clearance, airflow,
spacing of mounting brackets and flange holes, and connecting to the building structure.
Copyright © 2016, Juniper Networks, Inc.
33
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 18: Rack Requirements for the Services Gateway
Rack Requirement
Specifications
Size
A 19 in. (48.3 cm) rack as defined in Cabinets, Racks, Panels, and Associated
Equipment (document number EIA-310-D) published by the Electronics
Industry Association (http://www.eia.org).
Clearance
•
The outer edges of the mounting brackets extend the width of either
chassis to 19 in. (48.3 cm).
•
The front of the chassis extends approximately 0.5 in. (1.27 cm) beyond
the mounting ears.
•
Maximum permissible ambient temperature when two devices are
placed side by side in a 19 in. rack is 40° C.
•
The holes within each rack set are spaced at 1 U [1.75 in. (4.5 cm)]. The
device can be mounted in any rack that provides holes or hole patterns
spaced at 1-U [1.75 in. (4.5 cm)] increments.
•
The mounting brackets and front-mount flanges used to attach the
chassis to a rack are designed to fasten to holes spaced at rack
distances of 1 U (1.75 in.).
•
The mounting holes in the mounting brackets provided with the device
are spaced 1.25 in. (3.2 cm) apart (top and bottom mounting hole).
Spacing of Mounting
Bracket and Flange
Holes
Connecting to the
Building Structure
Related
Documentation
Always secure the rack in which you are installing the services gateway
to the structure of the building. If your geographical area is subject to
earthquakes, bolt the rack to the floor. For maximum stability, also secure
the rack to ceiling brackets.
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
SRX110 Services Gateway Cabinet Requirements on page 32
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway
When planning the installation site for the services gateway, consider the following:
•
The SRX110 Services Gateway requires unrestricted circulation of air to maintain an
optimal operating temperature.
NOTE: The SRX110 Services Gateway does not include a fan and uses
natural convection cooling.
•
34
For service personnel to remove and install hardware components, there must be
adequate space at the front and back of the device. Allow at least 24 in. (61 cm) both
in front of and behind the device.
Copyright © 2016, Juniper Networks, Inc.
Chapter 4: Planning and Preparing the Site
•
If you are mounting the device in a rack with other equipment, or if you are placing it
on the desktop near other equipment, ensure that the exhaust from other equipment
does not blow into the intake vents of the chassis.
Table 19 on page 35 provides clearance requirements for maintaining optimum airflow
and for facilitating maintenance of the device.
Table 19: Clearance Requirements for the Services Gateway
Related
Documentation
Location
Recommended
Clearance
Front of the chassis
2.5 in. (6.35 cm)
Space for service personnel to
remove and install hardware
components
Rear of the chassis
2.5 in. (6.35 cm)
Space for service personnel to
remove and install hardware
components
Between the front-mounting
flange and rack or cabinet edge
2.5 in. (6.35 cm)
Space for cable management and
organization
Between the side of the chassis
and any non-heat-producing
surface such as a wall or
cabinet side
2.5 in. (6.35 cm)
Space for the cooling system to
function properly and to maintain
unrestricted airflow around the
chassis
Between the side of the chassis
and devices that have fans or
blowers
2.5 in. (6.35 cm)
Space for the cooling system to
function properly and to maintain
unrestricted airflow around the
chassis
Requirement for Clearance
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
SRX110 Services Gateway Cabinet Requirements on page 32
•
SRX110 Services Gateway Rack Requirements on page 33
Copyright © 2016, Juniper Networks, Inc.
35
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
36
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 5
Power Requirements and Specifications
•
SRX110 Services Gateway Site Electrical Wiring Guidelines on page 37
•
SRX110 Services Gateway Electrical and Power Requirements on page 38
•
SRX110 Services Gateway Power Specifications and Requirements on page 39
SRX110 Services Gateway Site Electrical Wiring Guidelines
Table 20 on page 37 describes the factors you must consider while planning the electrical
wiring for the services gateway at your site.
CAUTION: It is particularly important to provide a properly grounded and
shielded environment and to use electrical surge-suppression devices.
CAUTION: For devices with AC power supplies, an external surge protective
device (SPD) must be used at the AC power source.
Table 20: Site Electrical Wiring Guidelines for the Services Gateway
Site Wiring Factor
Guideline
Signaling Limitations
To ensure that signaling functions optimally:
•
Install wires correctly.
Improperly installed wires can emit radio interference.
•
Do not exceed the recommended distances or pass wires
between buildings.
The potential for damage from lightning strikes increases if wires
exceed recommended distances or if wires pass between
buildings.
•
Shield all conductors.
The electromagnetic pulse (EMP) caused by lightning can
damage unshielded conductors and destroy electronic devices.
Copyright © 2016, Juniper Networks, Inc.
37
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 20: Site Electrical Wiring Guidelines for the Services
Gateway (continued)
Site Wiring Factor
Guideline
Radio Frequency
Interference (RFI)
To reduce or eliminate the emission of RFI from your site wiring:
Electromagnetic
Compatibility (EMC)
•
Use twisted-pair cable with a good distribution of grounding
conductors.
•
Use a high-quality twisted-pair cable with one ground conductor
for each data signal when applicable, if you must exceed the
recommended distances.
Provide a properly grounded and shielded environment and use
electrical surge-suppression devices.
Strong sources of electromagnetic interference (EMI) can cause
the following damage:
•
Destroy the signal drivers and receivers in the device
•
Conduct power surges over the lines into the equipment, resulting
in an electrical hazard
NOTE: If your site is susceptible to problems with EMC, particularly
from lightning or radio transmitters, you may want to seek expert
advice.
CAUTION: To comply with intrabuilding lightning/surge requirements, the
intrabuilding wiring must be shielded. The shielding for the wiring must be
grounded at both ends.
Related
Documentation
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
SRX110 Services Gateway Power Specifications and Requirements on page 39
SRX110 Services Gateway Electrical and Power Requirements
You must consider the following factors while planning the electrical wiring and power
availability at your site:
Related
Documentation
38
•
Power specifications and requirements for the device
•
Electrical wiring guidelines for the device installation site
•
Power, connection, and power cord specifications for the device
•
Grounding guidelines and specifications for the device
•
SRX110 Services Gateway Site Electrical Wiring Guidelines on page 37
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
Copyright © 2016, Juniper Networks, Inc.
Chapter 5: Power Requirements and Specifications
SRX110 Services Gateway Power Specifications and Requirements
The AC power system electrical specifications for the SRX110 Services Gateway are listed
in Table 21 on page 39.
Table 21: Power Supply Electrical Specifications for the SRX110 Services
Gateway
Power Requirement
Specification
AC input voltage
100 to 240 VAC
AC input line frequency
50 to 60 Hz
AC system current rating
1.5 A maximum
WARNING: The AC power cord for the services gateway is intended for use
with the device only and not for any other use.
Related
Documentation
•
SRX110 Services Gateway Electrical Safety Guidelines and Warnings on page 155
•
SRX110 Services Gateway Power Supply on page 9
•
SRX110 Services Gateway Grounding Specifications on page 71
Copyright © 2016, Juniper Networks, Inc.
39
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
40
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 6
Cable Specifications and Pinouts
•
Interface Cable and Wire Specifications for the SRX110 Services Gateway on page 41
•
RJ-45 Connector Pinouts for the SRX110 Services Gateway Ethernet Port on page 42
•
RJ-45 Connector Pinouts for the SRX110 Services Gateway Console Port on page 43
•
RJ-11 Connector Pinouts for the SRX110 Services Gateway on page 44
Interface Cable and Wire Specifications for the SRX110 Services Gateway
Table 22 on page 41 lists the specifications for the cables that connect to ports.
Table 22: Cable and Wire Specifications for Ports
Related
Documentation
Maximum
Length
Port
Cable Specification
Cable/Wire Required
Device Receptacle
Console
port
RS-232 (EIA-232)
serial cable
One 6 ft (1.83 m) length
with DB-9/RJ-45
connectors
6 ft
(1.83 m)
RJ-45
Ethernet
port
CAT-5e (Category 5)
cable or equivalent
suitable for
100BASE-T
operation
One 15 ft (4.57 m)
length with RJ-45/RJ-45
connectors
328 ft
(100 m)
RJ-45
VDSL2
port
•
For
VDSL/ADSL-POTS:
RJ-11 cable
•
18K ft
(5.486K
m)
•
For
VDSL/ADSL-POTS:
RJ-11
•
For
VDSL/ADSL-ISDN:
RJ-11/RJ-45 cable
For
VDSL/ADSL-POTS:
One 10 ft (3.048 m)
with RJ-11 connector
•
•
For
VDSL/ADSL-ISDN:
One 10 ft (3.048 m)
with RJ-45 connector
For
VDSL/ADSL-ISDN:
RJ-45
•
RJ-45 Connector Pinouts for the SRX110 Services Gateway Ethernet Port on page 42
•
RJ-45 Connector Pinouts for the SRX110 Services Gateway Console Port on page 43
•
RJ-11 Connector Pinouts for the SRX110 Services Gateway on page 44
Copyright © 2016, Juniper Networks, Inc.
41
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
RJ-45 Connector Pinouts for the SRX110 Services Gateway Ethernet Port
Figure 10 on page 42 shows the RJ-45 cable connector pinouts for Ethernet ports.
Figure 10: Ethernet Cable Connector (RJ-45)
Table 23 on page 42 describes the RJ-45 connector pinouts for the Ethernet port for
10/100 Mbps.
Table 23: RJ-45 Connector Pinouts for the Services Gateway Ethernet
Port (10/100 Mbps)
Pin
Signal
1
TX+
2
TX-
3
RX+
4
Termination network
5
Termination network
6
RX-
7
Termination network
8
Termination network
Table 24 on page 42 describes the RJ-45 connector pinouts for the Ethernet port for 1
Gbps (1000 Mbps).
Table 24: RJ-45 Connector Pinouts for the Services Gateway Ethernet
Port (1 Gbps)
42
Pin
Signal
1
BI_DA+
2
BI_DA-
3
BI_DB+
4
BI_DC+
5
BI_DC-
Copyright © 2016, Juniper Networks, Inc.
Chapter 6: Cable Specifications and Pinouts
Table 24: RJ-45 Connector Pinouts for the Services Gateway Ethernet
Port (1 Gbps) (continued)
Related
Documentation
Pin
Signal
6
BI_DB-
7
BI_DD+
8
BI_DD-
•
Interface Cable and Wire Specifications for the SRX110 Services Gateway on page 41
•
RJ-45 Connector Pinouts for the SRX110 Services Gateway Console Port on page 43
RJ-45 Connector Pinouts for the SRX110 Services Gateway Console Port
Figure 11 on page 43 shows the RJ-45 connector pinouts for the console port.
Figure 11: Console Cable Connector
Table 25 on page 43 describes the RJ-45 connector pinouts for the console port.
Table 25: RJ-45 Connector Pinouts for the Services Gateway Console
Port
Pin
Signal
Description
1
RTS
Request to Send
2
DTR
Data Terminal Ready
3
TXD
Transmit Data
4
Ground
Signal Ground
5
Ground
Signal Ground
6
RXD
Receive Data
7
DSR/DCD
Data Set Ready
8
CTS
Clear to Send
Copyright © 2016, Juniper Networks, Inc.
43
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Related
Documentation
•
Connecting and Organizing the SRX110 Services Gateway Interface Cables on page 75
•
Interface Cable and Wire Specifications for the SRX110 Services Gateway on page 41
RJ-11 Connector Pinouts for the SRX110 Services Gateway
Table 26 on page 44 describes the RJ-11 connector pinouts for the VDSL2 port.
Table 26: RJ-11 Connector Pinouts
Related
Documentation
44
Pin
Signal
1
No connect
2
No connect
3
RJ P –Ring
4
RJ N –Tip
5
No connect
6
No connect
•
Connecting and Organizing the SRX110 Services Gateway Interface Cables on page 75
•
Interface Cable and Wire Specifications for the SRX110 Services Gateway on page 41
Copyright © 2016, Juniper Networks, Inc.
PART 3
Initial Installation and Configuration
•
Installation Overview on page 47
•
Unpacking the Services Gateway on page 51
•
Installing the Mounting Hardware on page 55
•
Installing the Services Gateway on page 59
•
Grounding the SRX110 Services Gateway on page 71
•
Connecting the SRX110 Services Gateway to External Devices on page 75
•
Providing Power to the SRX110 Services Gateway on page 79
•
Performing Initial Configuration on page 83
Copyright © 2016, Juniper Networks, Inc.
45
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
46
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 7
Installation Overview
•
Installation Overview for the SRX110 Services Gateway on page 47
•
Required Tools and Parts for Installing and Maintaining the SRX110 Services
Gateway on page 48
•
SRX110 Services Gateway Autoinstallation Overview on page 49
Installation Overview for the SRX110 Services Gateway
After you prepare your installation site, you are ready to unpack and install the services
gateway. It is important to perform the installation procedure as indicated in
Table 27 on page 47.
Table 27: Installation Procedure for the SRX110 Services Gateway
Step
Task
Additional Information
1
Review the safety guidelines.
“SRX110 Services Gateway General Safety
Guidelines and Warnings” on page 131
2
Verify that you have prepared your
site for the installation of the
services gateway in accordance
with the checklist.
Site Preparation Checklist for the SRX110 Services
Gateway
3
Unpack the services gateway and
verify that all parts are received.
“Unpacking the SRX110 Services Gateway” on
page 51
4
Prepare the services gateway for
installation.
Preparing the SRX110 Services Gateway for
Rack-Mount, Desk-Mount, and Wall-Mount
Installation
5
Install the services gateway.
“Installing the SRX110 Services Gateway in a Rack”
on page 59
“Installing the SRX110 Services Gateway on a Desk”
on page 63
“Installing the SRX110 Services Gateway on a Wall”
on page 65
Copyright © 2016, Juniper Networks, Inc.
47
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 27: Installation Procedure for the SRX110 Services
Gateway (continued)
Step
Task
Additional Information
6
Connect cables to external devices.
“Connecting and Organizing the SRX110 Services
Gateway Interface Cables” on page 75
7
Connect the grounding cables.
“Grounding the SRX110 Services Gateway” on
page 72
8
Power on the services gateway.
“Powering On the SRX110 Services Gateway” on
page 80
“Powering Off the SRX110 Services Gateway” on
page 81
Related
Documentation
•
Unpacking the SRX110 Services Gateway on page 51
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
Preparing the SRX110 Services Gateway for Rack-Mount, Desk-Mount, and Wall-Mount
Installation
Required Tools and Parts for Installing and Maintaining the SRX110 Services Gateway
Table 28 on page 48 lists the tools and equipments required for installing and maintaining
the SRX110 Services Gateway.
Table 28: Required Tools and Parts for Installing and Maintaining the
SRX110 Services Gateway
Task
Tools and Parts
Additional Information
Installing the SRX110
Services Gateway
•
Phillips (+) screwdriver,
number 1
“Installing the SRX110 Services
Gateway in a Rack” on page 59
•
Phillips (+) screwdriver,
number 3
•
Tie wrap
“Installing the SRX110 Services
Gateway on a Desk” on page 63
“Installing the SRX110 Services
Gateway on a Wall” on page 65
48
Connecting the
SRX110 Services
Gateway
Electrostatic discharge (ESD)
grounding wrist strap
“Connecting the SRX110 Services
Gateway to the Power Supply” on
page 79
Grounding the SRX110
Services Gateway
Phillips (+) screwdriver,
number 1
“Grounding the SRX110 Services
Gateway” on page 72
Copyright © 2016, Juniper Networks, Inc.
Chapter 7: Installation Overview
Table 28: Required Tools and Parts for Installing and Maintaining the
SRX110 Services Gateway (continued)
Related
Documentation
Task
Tools and Parts
Additional Information
Packing the SRX110
Services Gateway
•
Electrostatic bag or
antistatic mat, for each
component
“Packing the SRX110 Services Gateway
and Components for Shipment” on
page 125
•
Electrostatic discharge
(ESD) grounding wrist strap
•
Unpacking the SRX110 Services Gateway on page 51
•
Grounding the SRX110 Services Gateway on page 72
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Packing the SRX110 Services Gateway and Components for Shipment on page 125
SRX110 Services Gateway Autoinstallation Overview
The autoinstallation process begins any time a services gateway is powered on and
cannot locate a valid configuration file in the internal flash memory device. Typically, a
configuration file is unavailable when a services gateway is powered on for the first time
or if the configuration file is deleted from the internal flash memory device.
The autoinstallation feature enables you to deploy multiple services gateways from a
central location in the network.
If you are setting up many devices, autoinstallation can help automate the configuration
process by loading configuration files onto new or existing devices automatically over
the network. You can use either the J-Web configuration editor or the command-line
interface (CLI) configuration editor to configure a device for autoinstallation.
For the autoinstallation process to work, you must store one or more host-specific or
default configuration files on a configuration server in the network and have a service
available—typically Dynamic Host Configuration Protocol (DHCP)—to assign an IP address
to the services gateway.
Autoinstallation occurs automatically when you connect an Ethernet port on a new
services gateway to the network and power on the device. To simplify the process, you
can explicitly enable autoinstallation on a device and specify a configuration server, an
autoinstallation interface, and a protocol for IP address acquisition.
For more information about configuring autoinstallation, see the following topics:
Related
Documentation
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Grounding the SRX110 Services Gateway on page 72
Copyright © 2016, Juniper Networks, Inc.
49
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
50
•
Powering On the SRX110 Services Gateway on page 80
•
Powering Off the SRX110 Services Gateway on page 81
•
SRX110 Services Gateway Software Configuration Overview on page 83
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 8
Unpacking the Services Gateway
•
Unpacking the SRX110 Services Gateway on page 51
•
Verifying Parts Received with the SRX110 Services Gateway on page 51
Unpacking the SRX110 Services Gateway
The SRX110 Services Gateway is shipped in a cardboard carton. The carton also contains
an accessory box and the SRX110 Services Gateway Quick Start.
NOTE: The device is maximally protected inside the shipping carton. Do not
unpack it until you are ready to begin installation.
To unpack the services gateway:
1.
Open the box in which the device is shipped.
2. Verify the parts received against the packing list in Verifying Parts Received with the
SRX110 Services Gateway.
3. Store the shipping box and packing material in case you need to return or move the
device at a later time.
Related
Documentation
•
Required Tools and Parts for Installing and Maintaining the SRX110 Services Gateway
on page 48
•
Preparing the SRX110 Services Gateway for Rack-Mount, Desk-Mount, and Wall-Mount
Installation
•
Installation Overview for the SRX110 Services Gateway on page 47
Verifying Parts Received with the SRX110 Services Gateway
The services gateway shipment package contains a packing list that includes all parts
and accessories available with the device. Check the parts in the shipment against the
items on the packing list. The packing list specifies the part numbers and descriptions of
each part in your order.
If any part is missing, contact your Juniper Networks customer service representative.
Copyright © 2016, Juniper Networks, Inc.
51
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
A fully configured SRX110 Services Gateway contains the chassis with installed
components, listed in Table 29 on page 52, and an accessory box, which contains the
parts listed in Table 30 on page 52.
NOTE: The parts shipped with your device can vary depending on the
configuration you ordered.
Table 29: Parts List for a Fully Configured SRX110 Services Gateway
Part
Quantity
SRX110 Services Gateway with 8xFE ports, 1xUSB port, 1x3G-WAN USB port,
and base memory (2 GB RAM, 2 GB Flash)
1
Power supply adapter of 60 W
1
3-Prong Power Cord
1
DB-9 to RJ-45 Adapter, Straight Through, 7 feet
1
Extension cable for 3G USB modem
1
Table 30: Accessory Parts List for the SRX110 Services Gateway
Part
Quantity
Juniper Networks Product Warranty
1
End User License Agreement
1
Quick Start Guide
1
Security Products Safety Guide
1
Juniper Compliance Form Letter
1
Product Registration
1
NOTE: The mounting kits available for rack, wall, and desk installation of the
SRX110 Services Gateway must be ordered separately. Contact your Juniper
Networks customer service representative for more information.
Related
Documentation
52
•
Required Tools and Parts for Installing and Maintaining the SRX110 Services Gateway
on page 48
•
Unpacking the SRX110 Services Gateway on page 51
Copyright © 2016, Juniper Networks, Inc.
Chapter 8: Unpacking the Services Gateway
•
Preparing the SRX110 Services Gateway for Rack-Mount, Desk-Mount, and Wall-Mount
Installation
Copyright © 2016, Juniper Networks, Inc.
53
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
54
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 9
Installing the Mounting Hardware
•
Preparing the SRX110 Services Gateway for Rack-Mount Installation on page 55
•
Preparing the SRX110 Services Gateway for Desk-Mount Installation on page 56
•
Preparing the SRX110 Services Gateway for Wall-Mount Installation on page 57
Preparing the SRX110 Services Gateway for Rack-Mount Installation
You can mount an SRX110 Services Gateway on 4-post (telco) racks, enclosed cabinets,
and open-frame racks.
NOTE: The SRX110 Services Gateway cannot be center-mounted in a rack.
Table 31 on page 55 lists the tasks you need to perform before installing the device.
Table 31: SRX110 Services Gateway Preinstallation Checklist for
Rack-Mount Installation
Task
Additional Information
Verify that the site meets the requirements.
Site Preparation Checklist for the SRX110
Services Gateway
Verify that the racks or cabinets meet the specific
requirements.
“SRX110 Services Gateway Rack
Requirements” on page 33
Place the rack or cabinet in its permanent location,
allowing adequate clearance for airflow and
maintenance, and secure it to the building structure.
“Clearance Requirements for Airflow and
Hardware Maintenance of the SRX110
Services Gateway” on page 34
Remove the services gateway chassis from the
shipping carton.
“Unpacking the SRX110 Services Gateway”
on page 51
Copyright © 2016, Juniper Networks, Inc.
55
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 31: SRX110 Services Gateway Preinstallation Checklist for
Rack-Mount Installation (continued)
Task
Additional Information
Verify that you have the following parts available
in your rack-mounting kit for the SRX110 Services
Gateway:
•
Rack-mounting brackets
•
Mounting screws
•
Power supply adapter tray with screws
•
Adapter stopper bracket
Adjust the power supply adapter tray.
“Adjusting the Power Supply Adapter Tray
for the SRX110 Services Gateway for
Rack-Mount Installation” on page 62
NOTE: The rack-mounting kit is not shipped with the device and must be
ordered separately.
Related
Documentation
•
Unpacking the SRX110 Services Gateway on page 51
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
•
Preparing the SRX110 Services Gateway for Desk-Mount Installation on page 56
•
Preparing the SRX110 Services Gateway for Wall-Mount Installation on page 57
Preparing the SRX110 Services Gateway for Desk-Mount Installation
You can mount the services gateway on a desk or other level surface horizontally or
vertically. The four rubber feet attached to the chassis provide stability.
Table 32 on page 56 provides the list of tasks you need to perform before installing the
device.
Table 32: SRX110 Services Gateway Preinstallation Checklist for
Desk-Mount Installation
56
Task
Additional Information
Verify that the site meets the requirements.
Site Preparation Checklist for the SRX110
Services Gateway
Place the desk in its permanent location, allowing
adequate clearance for airflow and maintenance, and
secure it to the building structure.
“Clearance Requirements for Airflow and
Hardware Maintenance of the SRX110
Services Gateway” on page 34
Copyright © 2016, Juniper Networks, Inc.
Chapter 9: Installing the Mounting Hardware
Table 32: SRX110 Services Gateway Preinstallation Checklist for
Desk-Mount Installation (continued)
Task
Additional Information
Remove the services gateway chassis from the
shipping carton.
“Unpacking the SRX110 Services
Gateway” on page 51
Verify that you have the following parts available in
your desk-mounting kit to mount the SRX110 Services
Gateway vertically:
•
Vertical stand
•
Screws
NOTE: If you are mounting the services gateway horizontally on a desk, ensure
that the rubber feet are attached to the chassis.
NOTE: The vertical desk-mounting kit is not shipped with the device and
must be ordered separately.
Related
Documentation
•
Unpacking the SRX110 Services Gateway on page 51
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
•
Preparing the SRX110 Services Gateway for Rack-Mount Installation on page 55
•
Preparing the SRX110 Services Gateway for Wall-Mount Installation on page 57
Preparing the SRX110 Services Gateway for Wall-Mount Installation
You can mount an SRX110 Services Gateway on a wall. The four rubber feet attached to
the chassis provide stability.
Table 33 on page 57 provides the list of tasks you need to perform before installing the
device.
Table 33: SRX110 Services Gateway Preinstallation Checklist for
Wall-Mount Installation
Task
Additional Information
Verify that the site meets the requirements.
Site Preparation Checklist for the SRX110
Services Gateway
Remove the services gateway chassis from the shipping
carton.
“Unpacking the SRX110 Services
Gateway” on page 51
Copyright © 2016, Juniper Networks, Inc.
57
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 33: SRX110 Services Gateway Preinstallation Checklist for
Wall-Mount Installation (continued)
Task
Additional Information
Verify that you have the following parts available in your
wall-mounting kit to mount the SRX110 Services
Gateway on a wall:
•
Wall-mounting brackets
•
Screws
NOTE: The wall-mounting kit is not shipped with the device and must be
ordered separately.
Related
Documentation
58
•
Unpacking the SRX110 Services Gateway on page 51
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
•
Preparing the SRX110 Services Gateway for Rack-Mount Installation on page 55
•
Preparing the SRX110 Services Gateway for Desk-Mount Installation on page 56
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 10
Installing the Services Gateway
•
Installing the SRX110 Services Gateway in a Rack on page 59
•
Adjusting the Power Supply Adapter Tray for the SRX110 Services Gateway for
Rack-Mount Installation on page 62
•
Installing the SRX110 Services Gateway on a Desk on page 63
•
Installing the SRX110 Services Gateway on a Wall on page 65
•
Installing a 3G USB Modem in the SRX110 Services Gateway USB Port on page 67
Installing the SRX110 Services Gateway in a Rack
You can front-mount the SRX110 Services Gateway in a rack. Many types of racks are
acceptable, including 4-post (telco) racks, enclosed cabinets, and open-frame racks.
For more information about the type of rack or cabinet that the SRX110 Services Gateway
can be installed into, see “SRX110 Services Gateway Rack Requirements” on page 33.
NOTE: The rack-mounting kit is not shipped with the device and must be
ordered separately.
NOTE:
Copyright © 2016, Juniper Networks, Inc.
•
If you are installing multiple devices in one rack, install the first device in
the lowest position in the rack and proceed upward in the rack.
•
Ensure that the rubber feet on the base of the chassis are removed for rack
installation.
59
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
To install the device in a rack:
Position a mounting bracket on each side of the chassis as shown in
Figure 12 on page 60.
1.
Figure 12: SRX110 Services Gateway Installation in a Rack — Positioning
Mounting Brackets
g033609
4
Table 34 on page 60 lists the parts used for installing the device on the rack. The
numbers in Figure 12 on page 60 correspond to the numbers in Table 34 on page 60.
Table 34: SRX Services Gateway Rack Installation Parts
Number
Part
1
Power supply adapter tray
2
Adapter stopper bracket
3
Mounting brackets
4
Screws (mounting bracket)
2. Use a Phillips (+) screwdriver, number 1, to install the screws that secure the mounting
brackets and power supply adapter tray to the chassis as shown in Figure 13 on page 60.
g033610
Figure 13: SRX110 Services Gateway Rack Installation — Securing Mounting
Brackets and Power Supply Adapter Tray
60
Copyright © 2016, Juniper Networks, Inc.
Chapter 10: Installing the Services Gateway
3. Place the power supply adapter in the tray as shown in Figure 14 on page 61.
g033611
Figure 14: SRX110 Services Gateway Rack Installation — Positioning Power
Supply Adapter Tray
4. Have one person grasp the sides of the device, lift it, and position it in the rack.
5. Align the bottom hole in each mounting bracket with a hole in each rack rail as shown
in Figure 15 on page 61, making sure that the chassis is level.
g033612
Figure 15: SRX110 Services Gateway Rack Installation — Hanging the
Services Gateway in a Rack
6. Have a second person install a mounting screw into each of the two aligned holes.
Use a Phillips (+) screwdriver, number 3, to tighten the screws.
Copyright © 2016, Juniper Networks, Inc.
61
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
7. Install the second screw in each mounting bracket.
8. Verify that the mounting screws on one side of the rack are aligned with the mounting
screws on the opposite side and that the device is level.
Related
Documentation
•
SRX110 Services Gateway Installation Safety Guidelines and Warnings on page 139
•
Required Tools and Parts for Installing and Maintaining the SRX110 Services Gateway
on page 48
•
SRX110 Services Gateway General Safety Guidelines and Warnings on page 131
•
Preparing the SRX110 Services Gateway for Rack-Mount Installation on page 55
•
Adjusting the Power Supply Adapter Tray for the SRX110 Services Gateway for
Rack-Mount Installation on page 62
•
Installing the SRX110 Services Gateway on a Desk on page 63
Adjusting the Power Supply Adapter Tray for the SRX110 Services Gateway for
Rack-Mount Installation
This topic provides details on the power supply adapter for the SRX110 Services Gateway
and the procedure for adjusting the power supply adapter tray to hold the power supply
adapter.
A 60-watt power supply adapter is provided with the SRX110 Services Gateway.
To accommodate the 60-watt power supply, use the two 420–028535 screws to attach
the adapter stopper brackets at the point on the chassis marked B.
Figure 16 on page 62 shows the adjustments to the power supply adapter tray required
for the 60-watt power supply.
g033608
Figure 16: Adjusting the Power Supply Adapter Tray to Accommodate the
60-Watt Power Supply
62
Copyright © 2016, Juniper Networks, Inc.
Chapter 10: Installing the Services Gateway
1.
Locations for the adapter stopper brackets in the power supply adapter tray
2. Fully configured power supply adapter tray
Related
Documentation
•
Preparing the SRX110 Services Gateway for Rack-Mount, Desk-Mount, and Wall-Mount
Installation
•
SRX110 Services Gateway Power Supply on page 9
Installing the SRX110 Services Gateway on a Desk
Follow these guidelines when installing the device on a desk:
•
You can install the SRX110 Services Gateway on a desk, table, or other level surface.
•
The device is shipped with the rubber feet attached. The rubber feet are necessary to
stabilize the device on the desk.
•
You can install the device in a horizontal or vertical position.
•
The vertical position requires the vertical installation kit, which consists of a vertical
installation stand with the rubber feet attached.
NOTE: The desk-mounting kit is not shipped with the device and must be
ordered separately.
To install the device in a horizontal position:
The horizontal position is the standard installation position and does not require the
vertical installation kit.
1.
Make sure that the rubber feet are attached to the chassis.
2. Place the device on a desk with the Juniper Networks logo facing up. The logo is
embossed on the top cover.
To install the device in a vertical position:
1.
Place the device on a flat and level surface, with the Juniper Networks logo facing up.
The logo is embossed on the top cover.
2. Attach the vertical stand to the right side of the chassis, using the specified screws
as shown in Figure 17 on page 64.
Copyright © 2016, Juniper Networks, Inc.
63
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
g033613
Figure 17: SRX110 Services Gateway Desk Installation — Attaching the
Vertical Stand
3. Place the chassis vertically on the desk with the stand resting on the desk as shown
in Figure 18 on page 64.
g033614
Figure 18: SRX110 Services Gateway Desk Installation — Placing the
Services Gateway on a Desk
Related
Documentation
64
•
SRX110 Services Gateway Installation Safety Guidelines and Warnings on page 139
•
Required Tools and Parts for Installing and Maintaining the SRX110 Services Gateway
on page 48
Copyright © 2016, Juniper Networks, Inc.
Chapter 10: Installing the Services Gateway
•
Preparing the SRX110 Services Gateway for Rack-Mount, Desk-Mount, and Wall-Mount
Installation
•
Installing the SRX110 Services Gateway on a Wall on page 65
Installing the SRX110 Services Gateway on a Wall
You can install the SRX110 Services Gateway on a wall.
NOTE: The wall-mounting kit is not shipped with the device and must be
ordered separately.
To install the device on a wall:
Place the device on a flat, level surface, with the Juniper Networks logo facing up. The
logo is embossed on the top cover. Ensure that the rubber feet are attached to the
bottom of the chassis.
1.
2. Position a mounting bracket on each side of the chassis as shown in
Figure 19 on page 65.
g033615
Figure 19: SRX110 Services Gateway Wall Installation — Attaching the
Mounting Brackets
Table 35 on page 65 lists the parts to use to install the SRX110 Services Gateway on
a wall. The numbers in Figure 19 on page 65 correspond to the numbers in
Table 35 on page 65.
Table 35: SRX110 Services Gateway Wall Installation Parts
Number
Part
1
Mounting brackets
2
Screws (mounting bracket)
3. Use a Phillips (+) screwdriver, number 1, to install the screws that secure the mounting
brackets to the chassis.
4. If you are using wall anchors to support the chassis, install two pairs of anchors on
the wall.
Copyright © 2016, Juniper Networks, Inc.
65
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
5. Have one person grasp the sides of the device, lift it, and position it on the wall.
6. Have a second person install two pairs of mounting screws through the bracket holes
on either side of the device to secure it to the wall.
7. Verify that the mounting screws on one side are aligned with the mounting screws on
the opposite side and that the device is level (Figure 20 on page 66).
g033616
Figure 20: SRX110 Services Gateway Wall Installation — Attaching the
Mounting Brackets
Related
Documentation
66
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
Required Tools and Parts for Installing and Maintaining the SRX110 Services Gateway
on page 48
•
Preparing the SRX110 Services Gateway for Rack-Mount, Desk-Mount, and Wall-Mount
Installation
•
Adjusting the Power Supply Adapter Tray for the SRX110 Services Gateway for
Rack-Mount Installation on page 62
•
Installing the SRX110 Services Gateway in a Rack on page 59
•
Installing the SRX110 Services Gateway on a Desk on page 63
Copyright © 2016, Juniper Networks, Inc.
Chapter 10: Installing the Services Gateway
Installing a 3G USB Modem in the SRX110 Services Gateway USB Port
This topic includes the following sections:
•
Connecting the 3G USB Modem on the USB Modem Extension Cable-Mount on page 67
•
Installing a 3G USB Modem on the Rear Side of the SRX110 Services Gateway on page 68
Connecting the 3G USB Modem on the USB Modem Extension Cable-Mount
The 3G USB modem is secured with a USB protection cover as shown in
Figure 21 on page 67.
g033622
Figure 21: 3G USB Modem with USB Protection Cover
Table 36 on page 67 lists the components of the 3G USB modem with USB protection
cover.
Table 36: 3G USB Modem with USB Protection Cover Components
Number
Component
1
USB mount top cover
2
USB modem
3
USB mount (magnetic/non-magnetic)
Copyright © 2016, Juniper Networks, Inc.
67
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 36: 3G USB Modem with USB Protection Cover
Components (continued)
Number
Component
4
USB mount base
5
Lock
To connect the 3G USB modem on the USB modem extension cable-mount:
1.
Place the USB mount on the USB mount base.
2. Insert a 3G USB modem in the USB mount slot.
3. Close the USB mount top cover on the USB mount.
4. Lock the USB modem protection cover.
Installing a 3G USB Modem on the Rear Side of the SRX110 Services Gateway
To install the 3G USB modem on the rear side of the SRX110 Services Gateway:
1.
Before you begin, ensure that the device is powered off.
2. On the rear side of the device, insert the USB modem extension cable into the 3G-WAN
USB port until the cable is engaged (see Figure 22 on page 68).
g033606
Figure 22: Connecting the 3G USB modem to the SRX110 Services Gateway
68
Copyright © 2016, Juniper Networks, Inc.
Chapter 10: Installing the Services Gateway
NOTE:
• The 3G USB modem is not hot-swappable.
•
Ensure that the base of the 3G USB extension of the cable mount is 18
inches away from the device.
3. Power on the device. The 3G LED on the front panel of the device indicates the status
of the 3G USB modem interface.
NOTE: You can wall-mount the modem using keyholes as shown in
Figure 23 on page 69 or ceiling mount the USB protection cover using screw
holes as shown in Figure 24 on page 69.
g033623
Figure 23: 3G USB Modem Wall Installation—Attaching the USB Protection
Cover
g033624
Figure 24: 3G USB Modem Ceiling Installation—Attaching the USB
Protection Cover
Copyright © 2016, Juniper Networks, Inc.
69
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Related
Documentation
70
•
SRX110 Services Gateway 3G USB Modem Overview on page 10
•
SRX110 Services Gateway 3G-WAN USB Port Physical Specifications on page 32
•
Configuring the 3G USB Modem on the SRX110 Services Gateway on page 102
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 11
Grounding the SRX110 Services Gateway
•
SRX110 Services Gateway Grounding Specifications on page 71
•
Grounding the SRX110 Services Gateway on page 72
SRX110 Services Gateway Grounding Specifications
To meet safety and electromagnetic interference (EMI) requirements and to ensure
proper operation, the services gateway must be adequately grounded before power is
connected. A grounding point available on the rear of the services gateway chassis is
used to connect the device to earth ground.
WARNING: Before device installation begins, a licensed electrician must
attach a cable lug to the grounding and power cables that you use. A cable
with an incorrectly attached lug can damage the device (for example, by
causing a short circuit).
To ground the device before connecting power, you connect the grounding cable to earth
ground and then attach the lug on the cable to the chassis grounding point with the
screw.
Table 37 on page 71 lists the specifications for the grounding cable used with the device.
Table 37: Grounding Cable Specifications for the Services Gateway
Related
Documentation
Grounding Requirement
Specification
Grounding cable
14 AWG single-strand wire cable
Amperage of grounding cable
Up to 4 A
Grounding lug
Ring-type, vinyl-insulated TV14-6R lug or
equivalent
•
SRX110 Services Gateway Site Electrical Wiring Guidelines on page 37
•
SRX110 Services Gateway Power Specifications and Requirements on page 39
•
Interface Cable and Wire Specifications for the SRX110 Services Gateway on page 41
Copyright © 2016, Juniper Networks, Inc.
71
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
Grounding the SRX110 Services Gateway on page 72
Grounding the SRX110 Services Gateway
To meet safety and electromagnetic interference (EMI) requirements and to ensure
proper operation, you must adequately ground the SRX110 Services Gateway before
connecting power.
Figure 25 on page 72 illustrates connecting a grounding cable to the services gateway.
g033617
Figure 25: Grounding the SRX110 Services Gateway
To ground the device, connect a grounding cable to earth ground and then attach it to
the chassis grounding points, using one M3 screw.
Table 38 on page 72 lists the specifications of the grounding cable used with the device.
Table 38: Grounding Cable Specifications for the Services Gateway
Grounding Requirement
Specification
Grounding cable
14 AWG single-strand wire cable
Amperage of grounding cable
Up to 4 A
Grounding lug
Ring-type, vinyl-insulated TV14-6R lug or
equivalent
CAUTION: Before device installation begins, a licensed electrician must
attach a cable lug to the grounding and power cables that you use. A cable
with an incorrectly attached lug can damage the device (for example, by
causing a short circuit).
72
Copyright © 2016, Juniper Networks, Inc.
Chapter 11: Grounding the SRX110 Services Gateway
To ground the device:
1.
Connect the grounding cable to a proper earth ground.
2. Verify that a licensed electrician has attached the cable lug to the grounding cable.
3. Place the grounding cable lug over the grounding point on the upper rear of the chassis.
4. Secure the grounding cable lug to the grounding point with the screw. Apply between
6 in.-lb (0.67 Nm) and 8 in.-lb (0.9 Nm) of torque to the screws.
5. Dress the grounding cable, and verify that it does not touch or block access to the
services gateway components and that it does not cause a tripping hazard.
NOTE: The device should be permanently connected to ground during normal
operation.
Related
Documentation
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Connecting and Organizing the SRX110 Services Gateway Interface Cables on page 75
•
SRX110 Services Gateway Grounding Specifications on page 71
•
Powering On the SRX110 Services Gateway on page 80
•
Powering Off the SRX110 Services Gateway on page 81
•
SRX110 Services Gateway General Safety Guidelines and Warnings on page 131
Copyright © 2016, Juniper Networks, Inc.
73
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
74
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 12
Connecting the SRX110 Services Gateway
to External Devices
•
Connecting and Organizing the SRX110 Services Gateway Interface Cables on page 75
•
Connecting the Modem at the SRX110 Services Gateway End on page 76
•
Connecting the Modem to the Console Port on the SRX110 Services Gateway on page 77
•
Connecting to the CLI at the User End for the SRX110 Services Gateway on page 77
Connecting and Organizing the SRX110 Services Gateway Interface Cables
You can connect the interfaces installed in the services gateway to various network
media. Each type of interface on the services gateway uses a particular medium to
transmit data. You must configure each network interface before it can operate on the
device.
To connect and organize an interface cable for the device:
1.
Have ready a length of the type of cable used by the interface.
2. Insert the cable connector into the cable connector port on the interface faceplate.
3. Arrange network cables as follows to prevent them from dislodging or developing
stress points:
Related
Documentation
•
Secure cables so that they are not supporting their own weight as they hang to the
floor.
•
Place excess cable out of the way in neatly coiled loops.
•
Use fasteners to maintain the shape of cable loops.
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Grounding the SRX110 Services Gateway on page 72
•
Interface Cable and Wire Specifications for the SRX110 Services Gateway on page 41
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
Copyright © 2016, Juniper Networks, Inc.
75
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Connecting the Modem at the SRX110 Services Gateway End
NOTE: These instructions use Hayes-compatible modem commands to
configure the modem. If your modem is not Hayes-compatible, refer to the
documentation for your modem and enter the equivalent modem commands.
To configure the modem on the services gateway end:
1.
Connect the modem to a PC or laptop computer.
2. Power on the modem.
3. From the PC or laptop computer, start your asynchronous terminal emulation
application (such as Microsoft Windows HyperTerminal), and select the COM port to
which the modem is connected (for example, COM1).
4. Configure the port settings as shown in Table 39 on page 76.
Table 39: Port Settings for Configuring the Modem on the Services
Gateway End
Port Setting
Value
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Flow control
None
5. In the HyperTerminal window, enter AT.
For more information on the AT commands, see the following topics:
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
An OK response verifies that the modem can communicate successfully with the COM
port on the PC or laptop.
6. Configure the modem to answer a call on the first ring by entering ATS0=1.
7. Configure the modem to accept modem control DTR signals by entering AT&D1.
8. Disable flow control by entering AT&K0.
9. Save modem settings by entering AT&W.
76
Copyright © 2016, Juniper Networks, Inc.
Chapter 12: Connecting the SRX110 Services Gateway to External Devices
Related
Documentation
•
Connecting the Modem to the Console Port on the SRX110 Services Gateway on page 77
•
Connecting to the CLI at the User End for the SRX110 Services Gateway on page 77
•
SRX110 Services Gateway Software Configuration Overview on page 83
Connecting the Modem to the Console Port on the SRX110 Services Gateway
To connect the dial-up modem to the console port on the services gateway:
1.
Turn off power to the services gateway.
2. Turn off power to the modem.
3. Plug one end of the Ethernet cable supplied with your services gateway into the
console port on the services gateway.
4. Plug the other end of the CAT-5e cable (Ethernet cable) into the RJ-45 to DB-9 serial
port adapter supplied with your services gateway.
5. Connect the serial port adapter to a separately purchased DB-9 female to DB-25
male adapter or other adapter appropriate for your modem.
6. Plug the modem adapter into the DB-25 connector on the modem.
7. Connect the modem to your telephone network.
8. Turn on the power to the modem.
9. Power on the services gateway by pressing the Power button on the front panel. Verify
that the Power LED on the front panel turns green.
NOTE: Most modems have an RS-232 DB-25 connector. You must
separately purchase an adapter to connect your modem to the RJ-45 to
DB-9 adapter and the Ethernet cable supplied with the services gateway.
Related
Documentation
•
Connecting the Modem at the SRX110 Services Gateway End on page 76
•
Connecting to the CLI at the User End for the SRX110 Services Gateway on page 77
•
SRX110 Services Gateway Software Configuration Overview on page 83
Connecting to the CLI at the User End for the SRX110 Services Gateway
To remotely connect to the CLI through a dial-up modem connected to the console port
on the services gateway:
1.
Connect a modem at your remote location to a management device such as a PC or
laptop computer.
2. Start your asynchronous terminal emulation application (such as Microsoft Windows
HyperTerminal) on the PC or laptop computer.
Copyright © 2016, Juniper Networks, Inc.
77
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
3. Select the COM port to which the modem is connected (for example, COM1).
4. Configure the port settings shown in Table 40 on page 78.
Table 40: Port Settings for Connecting to the CLI at User End
Port Setting
Value
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Flow control
None
5. In the HyperTerminal window, enter AT.
For more information on the AT commands, see the following topics:
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
An OK response verifies that the modem can communicate successfully with the COM
port on the PC or laptop.
6. Dial the modem that is connected to the console port on the services gateway by
entering ATDT remote-modem-number. For example, if the number of the modem
connected to the console port on the services gateway is 0013033033030, enter ATDT
0013033033030.
The services gateway login prompt appears.
7. Log in as the user root. No password is required at initial connection, but you must
assign a root password before committing any configuration settings.
Related
Documentation
78
•
Connecting the Modem at the SRX110 Services Gateway End on page 76
•
Connecting the Modem to the Console Port on the SRX110 Services Gateway on page 77
•
SRX110 Services Gateway Software Configuration Overview on page 83
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 13
Providing Power to the SRX110 Services
Gateway
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Powering On the SRX110 Services Gateway on page 80
•
Powering Off the SRX110 Services Gateway on page 81
Connecting the SRX110 Services Gateway to the Power Supply
To connect the device to the power supply:
CAUTION: Before connecting the device to the power supply, attach an ESD
strap to an ESD point and place the other end of the strap around your bare
wrist.
NOTE: If you are installing your services gateway on a desk, ensure that your
device is adequately grounded using the grounding point on the back panel
of the chassis.
1.
Plug the DC connector end of the power cable into the power connector on the back
of the device (see Figure 26 on page 80).
2. Plug the AC adapter end of the power cable into an AC power outlet.
Copyright © 2016, Juniper Networks, Inc.
79
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
g033618
Figure 26: Connecting the SRX110 Services Gateway to the Power Supply
NOTE: The device must be connected to earth ground during normal
operation. The protective earthing terminal on the rear of the chassis is
provided to connect the device to ground.
CAUTION: We recommend using a surge protector for the power connection.
NOTE: Use the cable tie holder to secure the power cord on the power supply
point.
NOTE: We strongly recommend that you use only the 3-prong power cord
supplied with your services gateway. If you are using a 2-prong power cord,
then ensure that your device is adequately grounded using the grounding
point available on the back panel of the chassis.
Related
Documentation
•
Required Tools and Parts for Installing and Maintaining the SRX110 Services Gateway
on page 48
•
Grounding the SRX110 Services Gateway on page 72
•
Connecting and Organizing the SRX110 Services Gateway Interface Cables on page 75
•
SRX110 Services Gateway General Safety Guidelines and Warnings on page 131
Powering On the SRX110 Services Gateway
To power on the services gateway:
1.
80
Ensure that you have connected the power supply to the device.
Copyright © 2016, Juniper Networks, Inc.
Chapter 13: Providing Power to the SRX110 Services Gateway
2. Insert the plug of the power supply adapter into an AC power source receptacle.
3. Turn on the power to the services gateway.
The device starts automatically as the power supply completes its startup sequence.
The Power LED lights up during startup and remains on when the device is operating
normally.
NOTE: After the power supply is turned on, it can take up to 60 seconds for
status indicators—such as the Status and Power LEDs—to show that the
power supply is functioning normally.
NOTE: We recommend you issue the CLI command request system power-off
when you want to power off the device immediately after powering it on.
Related
Documentation
•
Powering Off the SRX110 Services Gateway on page 81
•
Resetting the SRX110 Services Gateway on page 114
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Grounding the SRX110 Services Gateway on page 72
•
Using the Reset Config Button on the SRX110 Services Gateway on page 115
•
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2
•
SRX110 Services Gateway LEDs
Powering Off the SRX110 Services Gateway
You can power off the services gateway in one of two ways:
•
Graceful shutdown — Press and release the Power button. The device begins gracefully
shutting down the operating system and then powers itself off.
•
Forced shutdown — Press the Power button and hold it for more than 10 seconds. The
device immediately powers itself off without shutting down the operating system.
NOTE: Do not press the Power button while the device is shutting down.
CAUTION: Use the graceful shutdown method to halt, power off, or reboot
the services gateway. Use the forced shutdown method as a last resort to
recover the services gateway if the services gateway operating system is not
responding to the graceful shutdown method.
Copyright © 2016, Juniper Networks, Inc.
81
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
CAUTION: Forced shutdown can result in data loss and corruption of the file
system.
NOTE: To remove power completely from the device, unplug the AC power
cord or switch off the power source.
After powering off a power supply, wait at least 10 seconds before turning it
back on. After powering on a power supply, wait at least 10 seconds before
turning it off.
The Power button on the services gateway is a standby power switch.
If you press the Power button to power off the device when it is still connected
to a power source, 12-V power will still be available in the chassis and the
device will be fully powered off.
NOTE: When you are powering off the device, the system displays the
following message: Turning the system power off. You can now safely remove
the power cable to completely disconnect the power from the device.
NOTE: You can use the request system reboot command to schedule a reboot
of the services gateway.
For more information about halting, powering off, or rebooting the services gateway using
the CLI, see the following topics:
Related
Documentation
82
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
•
Powering On the SRX110 Services Gateway on page 80
•
Resetting the SRX110 Services Gateway on page 114
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Grounding the SRX110 Services Gateway on page 72
•
Using the Reset Config Button on the SRX110 Services Gateway on page 115
•
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2
•
SRX110 Services Gateway LEDs
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 14
Performing Initial Configuration
•
SRX110 Services Gateway Software Configuration Overview on page 83
•
Connecting the SRX110 Services Gateway to the J-Web Interface on page 86
•
SRX110 Services Gateway Secure Web Access Overview on page 87
•
Connecting the Services Gateway to the CLI Locally on page 88
•
Viewing Factory-Default Settings of the SRX110 Services Gateway on page 90
•
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
CLI on page 96
•
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
Setup Wizard on page 99
•
Configuring the 3G USB Modem on the SRX110 Services Gateway on page 102
•
Configuring the Integrated VDSL2 Interface on the SRX110 Services Gateway on page 103
SRX110 Services Gateway Software Configuration Overview
This topic includes the following sections:
•
Preparing the SRX110 Services Gateway for Configuration on page 83
•
Understanding Built-In Ethernet Ports on page 84
•
Understanding Management Access on page 85
Preparing the SRX110 Services Gateway for Configuration
When the device powers on, it tries to boot Junos OS from the default storage medium.
If the device fails to boot from the default storage medium, it tries to boot from the
alternate storage medium.
Table 41 on page 83 provides information on the storage media available on the services
gateway.
Table 41: Storage Media on the Services Gateway
Storage Media
Type
CompactFlash
Default; always present
USB storage device
Alternate
Copyright © 2016, Juniper Networks, Inc.
83
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
NOTE: The SRX Series devices that ship with Junos OS Release 10.0 or later
are formatted with dual-root partitions from the factory. SRX Series devices
that are running Junos OS Release 9.6 or earlier can be formatted with
dual-root partitions when they are upgraded to Junos OS Release 10.0 or
later.
For more information on dual-root partitioning, see the following topics:
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
You configure the services gateway by issuing Junos OS command-line interface (CLI)
commands.
Gather the following information before configuring the device:
•
Device name to be used on the network
•
Domain name the device will use
•
IP address and prefix length information for the Ethernet interface
•
IP address of a default router
•
IP address of a DNS server
•
Password for the root user
Understanding Built-In Ethernet Ports
Note the following points about the services gateway management ports:
84
•
The services gateway uses fe-0/0/1 to fe-0/0/7 as management ports to perform
initial device setup. Before initial configuration, when the factory-default configuration
is active, the device attempts to perform autoinstallation by obtaining a device
configuration through all of its connected interfaces.
•
The services gateway acts as a DHCP client out of the built-in Ethernet ports. If the
services gateway does not find a DHCP server within a few seconds, the device acts
as a DHCP server and assigns an IP address as 192.168.1.1/24. With the device
temporarily acting as a DHCP server, you can manually configure it with the J-Web
interface.
•
Any DHCP client host, for example, a PC or laptop computer, directly connected to any
of fe-0/0/1 to fe-0/0/7 ports receives an address on the 192.168.1.1/24 network.
•
Any DHCP client host, for example, a PC or laptop computer, directly connected to any
of fe-0/0/1 to fe-0/0/7 ports receives an address on the 192.168.1.1/24 network.
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
Understanding Management Access
Telnet allows you to connect to the services gateway and access the CLI to execute
commands from a remote system. The Telnet CLI connections are not encrypted and
therefore can be intercepted.
NOTE: Telnet access to the root user is prohibited. You must use more secure
methods, such as SSH, to log in as root.
SSH provides the following features:
•
Allows you to connect to the device and access the CLI to execute commands from a
remote system
•
Encrypts traffic so that it cannot be intercepted (unlike Telnet)
•
Can be configured so that connections are authenticated by a digital certificate
•
Uses public–private key technology for both connection and authentication
The SSH client software must be installed on the machine where the client application
runs. If the SSH private key is encrypted (for greater security), the SSH client must be
able to access the passphrase used to decrypt the key.
For information about obtaining SSH software, see http://www.ssh.com and
http://www.openssh.com.
If you are using a Junos XML management protocol server to configure and monitor
devices, you can activate cleartext access on the device to allow unencrypted text to be
sent directly over a Transmission Line Protocol (TCP) connection without using any
additional protocol (such as SSH, SSL, or Telnet). For more information about the Junos
XML management protocol application programming interface (API), see the NETCONF
XML Management Protocol Guide.
NOTE: Information sent in cleartext is not encrypted and therefore can be
intercepted.
If the device is operating in a Common Criteria environment, see the Configuration Guides
for Junos OS Public Sector Certifications.
Related
Documentation
•
Connecting the SRX110 Services Gateway to the J-Web Interface on page 86
•
Connecting the Services Gateway to the CLI Locally on page 88
•
Connecting the SRX110 Services Gateway to the CLI Remotely
•
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
CLI on page 96
Copyright © 2016, Juniper Networks, Inc.
85
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Connecting the SRX110 Services Gateway to the J-Web Interface
If you plan to use the J-Web interface to configure the SRX110 Services Gateway, you
must connect through one of the built-in Ethernet management ports.
When the services gateway is powered on for the first time, the system looks for a Dynamic
Host Configuration Protocol (DHCP) server. If it does not find one, the system assigns
an IP address within the 192.168.1.0/24 subnetwork to any devices connected to the
system.
To connect to the J-Web interface through any of the ports fe-0/0/1 through fe-0/0/7
on the services gateway, see Figure 27 on page 86.
g033619
Figure 27: Connecting to the Ethernet Port on an SRX110 Services Gateway
To connect to the Ethernet port:
1.
From the management device that you use to access the J-Web interface (such as a
PC or a laptop), verify that the address of the port you connect to is set to one of the
following values:
•
Ethernet address on the 192.168.1.0/24 subnetwork other than 192.168.1.1
•
Ethernet address from a DHCP server
2. Plug one end of the CAT-5e (Ethernet cable) into the Ethernet port on the management
device.
3. Connect the other end of the Ethernet cable to any of the built-in Ethernet ports
fe-0/0/1 through fe-0/0/7 on the services gateway.
4. Wait until the Status LED on the front panel of the services gateway turns solid green.
86
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
5. Turn on the power to the management device. The services gateway assigns an IP
address to the management device within the 192.168.1.0/24 subnetwork if the
management device is configured to use DHCP.
NOTE: After connecting the management device to the services gateway,
the DHCP server process on the services gateway assigns an IP address
automatically to the management device. Ensure that the management
device acquires an IP address on the 192.168.1.0/24 subnetwork (other
than 192.168.1.1) from the device.
6. From the management device, open a Web browser and enter the IP address 192.168.1.1
in the address field if the management device is configured using the DHCP.
7. Configure basic settings for your services gateway.
NOTE: You must manually configure the IP address for the management
port you are using before you save your initial configuration. When you save
the configuration for the first time, you will lose the connection to the services
gateway if you have not manually configured the IP address. If you lose the
connection through the management interface, you must connect through
the Console port.
Related
Documentation
•
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
CLI on page 96
•
Connecting the Services Gateway to the CLI Locally on page 88
•
SRX110 Services Gateway Software Configuration Overview on page 83
•
SRX110 Services Gateway Secure Web Access Overview on page 87
SRX110 Services Gateway Secure Web Access Overview
You can manage a services gateway remotely through the J-Web interface. To
communicate with the services gateway, the J-Web interface uses Hypertext Transfer
Protocol (HTTP). HTTP allows easy Web access but no encryption. The data that is
transmitted between the Web browser and the services gateway by means of HTTP is
vulnerable to interception and attack. To enable secure Web access, the services gateway
supports HTTP over Secure Sockets Layer (HTTPS). You can enable HTTP or HTTPS
access on specific interfaces and ports as needed.
The services gateway uses the SSL protocol to provide secure management of services
gateways through the J-Web. SSL uses public-private key technology that requires a
paired private key and an authentication certificate for providing the SSL service. SSL
encrypts communication between your device and the Web browser with a session key
negotiated by the SSL server certificate.
Copyright © 2016, Juniper Networks, Inc.
87
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
An SSL certificate includes identifying information such as a public key and a signature
made by a certificate authority (CA). When you access the services gateway through
HTTPS, an SSL handshake authenticates the server and the client and begins a secure
session. If the information does not match or if the certificate has expired, your access
to the services gateway through HTTPS is restricted.
Without SSL encryption, communication between your services gateway and the browser
is sent in the open and can be intercepted. We recommend that you enable HTTPS access
on your WAN interfaces.
For more information about configuring secure Web access, see the following topics:
Related
Documentation
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
•
SRX110 Services Gateway Software Configuration Overview on page 83
•
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
CLI on page 96
Connecting the Services Gateway to the CLI Locally
If you plan to use the command-line interface (CLI) to configure the SRX110 Services
Gateway, you must connect through the Console port, as shown in Figure 28 on page 88.
g033620
Figure 28: Connecting to the Console Port on an SRX110 Services Gateway
88
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
NOTE: Figure 28 on page 88 shows a connection to a local management
device. A remote connection to the services gateway through a modem
requires the cable and connector shown (provided in the services gateway
accessory box), plus a DB-9 male to DB-25 male (or similar) adapter for your
modem, which you must purchase separately.
To connect to the CLI using a local management device through the Console port on the
services gateway:
1.
Turn off power to the services gateway.
2. Turn off power to the management device, such as a PC or laptop computer, that you
are using to access the CLI.
3. Plug one end of the Ethernet cable supplied with your services gateway into the RJ-45
to DB-9 serial port adapter supplied with your services gateway (see
Figure 28 on page 88).
4. Plug the RJ-45 to DB-9 serial port adapter into the serial port on the management
device (see Figure 28 on page 88).
5. Connect the other end of the Ethernet cable to the Console port on the services
gateway (see Figure 28 on page 88).
6. Turn on the power to the management device.
7. Start your asynchronous terminal emulation application (such as Microsoft Windows
HyperTerminal), and select the appropriate COM port to use (for example, COM1).
8. Configure the port settings as shown in Table 42 on page 89.
Table 42: Port Settings for Connecting to the Console Port
Port Setting
Value
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Flow control
None
9. Power on the services gateway by pressing the Power button on the front panel.
10. Verify that the Power LED on the front panel turns green.
The terminal emulation screen on your management device displays the startup
sequence. When the services gateway has finished starting up, a login prompt appears.
11. Log in as the user root. No password is required at initial connection, but you must
assign a root password before committing any configuration settings.
Copyright © 2016, Juniper Networks, Inc.
89
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Related
Documentation
•
Connecting the SRX110 Services Gateway to the CLI Remotely
•
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
CLI on page 96
•
Connecting the SRX110 Services Gateway to the J-Web Interface on page 86
•
SRX110 Services Gateway Software Configuration Overview on page 83
•
SRX110 Services Gateway Secure Web Access Overview on page 87
Viewing Factory-Default Settings of the SRX110 Services Gateway
To view the factory-default configuration of the services gateway using the CLI:
1.
Verify that the services gateway is powered on.
2. Log in as the root user and provide your credentials.
3. In shell mode, navigate to the /etc/config folder.
% cd /etc/config
4. View the list of default config files.
% ls
The following sample output displays the list of factory-default configuration files:
j-series-defaults.conf
jsrxsme-series-defaults.conf
jsrxsme-series-factory.conf
junos-defaults.conf
junos-factory.conf
junos-fips-defaults.conf
ptx-series-defaults.conf
srx100-8xfe-factory.conf
srx100b-defaults.conf
srx100b-factory.conf
srx100h-defaults.conf
srx100h-factory.conf
srx100h2-defaults.conf
srx100h2-factory.conf
srx110-8xfe-vdsl-factory.conf
srx110-8xfe-vdsl-wl-factory.conf
srx110-8xfe-wl-factory.conf
srx110b-defaults.conf
srx110b-va-defaults.conf
srx110b-va-factory.conf
srx110b-vb-defaults.conf
srx110b-vb-factory.conf
srx110b-wl-defaults.conf
srx110b-wl-factory.conf
srx110h-defaults.conf
srx110h-va-defaults.conf
srx110h-va-factory.conf
srx110h-va-wl-defaults.conf
srx110h-va-wl-factory.conf
srx110h-vb-defaults.conf
srx110h-vb-factory.conf
90
srx210h-defaults.conf
srx210h-factory.conf
srx210h-poe-defaults.conf
srx210h-poe-factory.conf
srx210he-defaults.conf
srx210he-factory.conf
srx210he-poe-defaults.conf
srx210he-poe-factory.conf
srx210he2-defaults.conf
srx210he2-factory.conf
srx210he2-poe-defaults.conf
srx210he2-poe-factory.conf
srx220-8xge-factory.conf
srx220-poe-8xge-factory.conf
srx220h-defaults.conf
srx220h-factory.conf
srx220h-poe-defaults.conf
srx220h-poe-factory.conf
srx220h2-defaults.conf
srx220h2-factory.conf
srx220h2-poe-defaults.conf
srx220h2-poe-factory.conf
srx240-16xge-factory.conf
srx240-poe-16xge-factory.conf
srx240b-factory.conf
srx240b2-factory.conf
srx240h-dc-defaults.conf
srx240h-dc-factory.conf
srx240h-defaults.conf
srx240h-factory.conf
srx240h-poe-defaults.conf
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
srx110h-vb-wl-defaults.conf
srx110h-vb-wl-factory.conf
srx110h-wl-defaults.conf
srx110h-wl-factory.conf
srx110h2-va-defaults.conf
srx110h2-va-factory.conf
srx110h2-vb-defaults.conf
srx110h2-vb-factory.conf
srx210-2xge-6xfe-factory.conf
srx210-poe-2xge-6xfe-factory.conf
srx210b-defaults.conf
srx210b-factory.conf
srx210be-defaults.conf
srx210be-factory.conf
srx240h-poe-factory.conf
srx240h2-dc-defaults.conf
srx240h2-dc-factory.conf
srx240h2-defaults.conf
srx240h2-factory.conf
srx240h2-poe-defaults.conf
srx240h2-poe-factory.conf
srx550-6xge-factory.conf
srx550-defaults.conf
srx550-factory.conf
srx650-4xge-factory.conf
srx650-defaults.conf
srx650-factory.conf
5. View the required default config file.
% vi config file name
For example, enter the following command to view the default configuration file for
the SRX240 Services Gateway.
% vi srx240-poe-16xge-factory.conf
The following sample output displays the factory-default configuration on an SRX240
Services Gateway:
##
## $Id: $
##
## Copyright (c) 2009, Juniper Networks, Inc.
## All rights reserved.
##
system {
autoinstallation {
delete-upon-commit;
traceoptions {
level verbose;
flag {
all;
}
}
interfaces {
ge-0/0/0 {
bootp;
}
}
}
services {
ssh;
telnet;
dhcp {
router {
192.168.1.1;
}
pool 192.168.1.0/24 {
address-range low 192.168.1.2 high 192.168.1.254;
}
propagate-settings ge-0/0/0.0;
}
web-management {
http {
Copyright © 2016, Juniper Networks, Inc.
91
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
interface [ vlan.0 ];
}
https {
system-generated-certificate;
interface [ vlan.0 ];
}
}
xnm-clear-text;
}
name-server {
208.67.222.222;
208.67.220.220;
}
syslog {
archive size 100k files 3;
}
}
interfaces {
ge-0/0/0
unit
}
ge-0/0/1
unit
{
0;
{
0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/2 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/3 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/4 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
92
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
}
}
ge-0/0/5 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/6 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/7 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/8 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/9 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/10 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
Copyright © 2016, Juniper Networks, Inc.
93
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
}
ge-0/0/11 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/12 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/13 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/14 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
ge-0/0/15 {
unit 0 {
family ethernet-switching {
vlan {
members vlan-trust;
}
}
}
}
vlan {
unit 0 {
family inet {
address 192.168.1.1/24;
}
}
}
}
poe {
94
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
interface all;
}
security {
nat {
source {
rule-set trust-to-untrust {
from zone trust;
to zone untrust;
rule source-nat-rule {
match {
source-address 0.0.0.0/0;
}
then {
source-nat {
interface;
}
}
}
}
}
}
screen {
ids-option untrust-screen {
icmp {
ping-death;
}
ip {
source-route-option;
tear-drop;
}
tcp {
syn-flood {
alarm-threshold 1024;
attack-threshold 200;
source-threshold 1024;
destination-threshold 2048;
timeout 20;
}
land;
}
}
}
zones {
security-zone trust {
host-inbound-traffic {
system-services {
all;
}
protocols {
all;
}
}
interfaces {
vlan.0;
}
}
security-zone untrust {
interfaces {
ge-0/0/0.0 {
host-inbound-traffic {
Copyright © 2016, Juniper Networks, Inc.
95
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
system-services {
dhcp;
tftp;
}
}
}
}
screen untrust-screen;
}
}
policies {
from-zone trust to-zone untrust {
policy trust-to-untrust {
match {
source-address any;
destination-address any;
application any;
}
then {
permit;
}
}
}
}
}
vlans {
vlan-trust {
vlan-id 3;
l3-interface vlan.0;
}
}
protocols {
stp;
}
Related
Documentation
•
SRX110 Services Gateway Autoinstallation Overview on page 49
•
SRX110 Services Gateway Software Configuration Overview on page 83
•
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
CLI on page 96
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
CLI
This procedure connects the device to the network but does not enable it to forward
traffic. For complete information about enabling the device to forward traffic, including
examples, see the appropriate Junos OS configuration guides.
To configure the Junos OS:
1.
Verify that the device is powered on.
2. Log in as the root user. There is no password.
96
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
3. Start the CLI.
root# cli
root@>
4. Enter configuration mode.
configure
[edit]
root@#
5. Set the root authentication password by entering a cleartext password, an encrypted
password, or an SSH public key string (DSA or RSA).
[edit]
root@# set system root-authentication plain-text-password
New password: password
Retype new password: password
6. Configure an administrator account on the device.
[edit]
root@# set system login user admin class super-user authentication
plain-text-password
7. Commit the configuration to activate it on the device.
[edit]
root@# commit
8. Log in as the administrative user you configured in Step 6.
9. Configure the name of the device. If the name includes spaces, enclose the name in
quotation marks (“ ”).
configure
[edit]
admin@# set system host-name host-name
10. Configure the traffic interface.
[edit]
admin@# set interfaces fe-0/0/1 unit 0 family inet address address/prefix-length
11. Configure the default route.
[edit]
admin@# set routing-options static route 0.0.0.0/0 next-hop gateway
12. Configure basic security zones and bind them to traffic interfaces.
[edit]
admin@# set security zones security-zone untrust interfaces fe-0/0/1
Copyright © 2016, Juniper Networks, Inc.
97
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
13. Configure basic security policies.
[edit]
admin@# set security policies from-zone trust to-zone untrust policy policy-name
match source-address any destination-address any application any
root@# set security policies from-zone trust to-zone untrust policy policy-name then
permit
14. Create a NAT rule for source translation of all Internet bound traffic.
[edit]
admin@# set security nat source rule-set interface-nat from zone trust
admin@# set security nat source rule-set interface-nat to zone untrust
admin@# set security nat source rule-set interface-nat rule rule1 match source-address
0.0.0.0/0 destination-address 0.0.0.0/0
admin@# set security nat source rule-set interface-nat rule rule1 then source-nat
interface
15. Check the configuration for validity.
[edit]
admin@# commit check
configuration check succeeds
16. Commit the configuration to activate it on the device.
[edit]
admin@# commit
commit complete
17. Optionally, display the configuration to verify that it is correct.
[edit]
user@host# show
system {
host-name devicea;
domain-name lab.device.net;
domain-search [ lab.device.net device.net ];
backup-device 192.168.2.44;
time-zone America/Los_Angeles;
root-authentication {
ssh-rsa "ssh-rsa AAAAB3Nza...D9Y2gXF9ac==root@devicea.lab.device.net";
}
name-server {
10.148.2.32;
}
services {
}
ntp {
server 10.148.2.21;
}
}
interfaces {
fe-0/0/0 {
unit 0 {
family inet {
address 192.168.1.1/24;
}
}
98
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
}
lo0 {
unit 0 {
family inet {
address 172.16.1.24/32;
}
}
}
}
18. Commit the configuration to activate it on the device.
[edit]
admin@# commit
19. Optionally, configure additional properties by adding the necessary configuration
statements. Then commit the changes to activate them on the device.
[edit]
admin@host# commit
20. When you have finished configuring the device, exit configuration mode.
[edit]
admin@host# exit
admin@host>
Related
Documentation
•
SRX110 Services Gateway Secure Web Access Overview on page 87
•
SRX110 Services Gateway Software Configuration Overview on page 83
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
Setup Wizard
This topic describes how to perform the initial software configuration of your services
gateway using the new setup wizard available in Junos OS Release 12.1X44-D10 or later.
This topic includes the following sections:
•
About the Setup Wizard on page 99
•
About the Default Setup Mode on page 100
•
About the Guided Setup Mode on page 101
•
Running the Setup Wizard on page 101
About the Setup Wizard
The setup wizard guides you through the step-by-step configuration of a services gateway
that can securely pass traffic. To help guide you through the process, the wizard:
•
Provides recommended settings based on your previous selections. For example, the
wizard recommends security policies based on the security topology you have defined.
•
Determines which configuration tasks to present to you based on your selections.
Copyright © 2016, Juniper Networks, Inc.
99
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
Flags any missing required configuration when you attempt to leave a page.
•
Indicates which configuration elements or tasks are unavailable to you based on your
previous selections by graying them out.
You can choose one of the following setup modes to configure the services gateway:
•
Default Setup mode—This mode allows you to quickly set up a services gateway in a
default security configuration. In this mode, you can configure basic system settings,
such as the administrator password, and download purchased licenses. Any additional
configuration can be carried out after completing the wizard setup.
•
Guided Setup mode—This mode allows you to set up a services gateway in a custom
security configuration.
NOTE: It is mandatory to configure only the device name and root password.
You can skip all the other steps by clicking Next to go directly to the Confirm
& Apply page to apply the configuration.
About the Default Setup Mode
If you choose the Default Setup mode, the wizard takes you through the minimal
configuration needed to set up the services gateway to securely pass traffic in the default
configuration. The resulting configuration is similar to the factory-default configuration
described in “SRX110 Services Gateway Software Configuration Overview” on page 83,
except that the untrust and trust zones are renamed the Internet and Internal zones,
respectively.
In the Default Setup mode, you configure:
•
Device name
•
Password for the root account
•
Time information for the services gateway location
•
Local time zone
•
Name or IP address of a Network Time Protocol (NTP) server, if NTP is used to set
the time on the services gateway
•
Local date and time if an NTP server is not used to set the time
You cannot do additional configuration in the Default Setup mode. You must commit
your changes and exit the wizard to perform any additional configuration. You can perform
additional configuration by rerunning the wizard in the Guided Setup mode, by using the
J-Web interface, or by using the CLI.
See the SRX110 Services Gateway Quick Start for step-by-step instructions on how to
configure your services gateway in the Default Setup mode.
100
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
About the Guided Setup Mode
If you choose the Guided Setup mode, the wizard guides you through configuring your
services gateway in a custom security configuration. You can choose between the Basic
and Expert levels based on your experience level. The following table compares the Basic
and Expert levels.
Basic
Expert
Can configure only three internal zones
Can configure more than three internal zones
Can configure static and dynamic IP for the
Internet zone
Can configure static IP, static pool, and dynamic
IP for the Internet zone
Cannot configure internal zone service
Can configure internal zone service
Cannot configure internal destination NAT
Can configure internal destination NAT
Configurations you can perform with the setup wizard include:
•
Configuring basic options such as device name, root password, and system time
•
Configuring the security topology
•
Defining security zones and specifying which interfaces are in each zone
•
Configuring a DHCP server in a zone
•
Defining security policies and Network Address Translation (NAT) rules
•
Configuring remote access
See the SRX110 Services Gateway Quick Start for step-by-step instructions on how to
configure your services gateway in the Guided Setup mode.
Running the Setup Wizard
To run the setup wizard:
1.
Connect a laptop or desktop computer to any of ports 0/1 through 0/7 as described
in Establishing Basic Connectivity.
2. Open a Web browser on your laptop or desktop.
NOTE: The wizard works best with Mozilla Firefox version 15.x or later.
The minimum screen resolution is 800 by 600 pixels.
3. Enter the URL http://192.168.1.1.
When the Welcome page for the setup wizard appears, choose the setup mode you
want to use to configure your services gateway.
Copyright © 2016, Juniper Networks, Inc.
101
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
NOTE: Before applying the configuration changes to the services gateway,
check the connectivity to the services gateway. You might lose connectivity
if you have changed the management zone IP. Click the URL for reconnection
instructions for information on how to reconnect to the device.
After you finish configuring the services gateway with the setup wizard and commit your
configuration, you are redirected to the J-Web interface. Thereafter, whenever you connect
to the services gateway, you are placed in the J-Web interface. You can access the setup
wizard from the J-Web interface and use it to reconfigure your services gateway. To do
so, select Tasks > Run Setup Wizard. You can either edit an existing configuration or create
a new configuration.
NOTE: If you elect to create a new configuration, then all the current
configuration in the services gateway will be deleted.
Related
Documentation
•
Performing Initial Software Configuration on the SRX110 Services Gateway Using the
CLI on page 96
•
SRX110 Services Gateway Software Configuration Overview on page 83
•
SRX110 Services Gateway Secure Web Access Overview on page 87
Configuring the 3G USB Modem on the SRX110 Services Gateway
Table 43 on page 102 lists the basic CLI commands for operating the 3G USB modem on
the services gateway.
The 3G wireless interface uses the prefix cl in the syntax cl-slot-number/0/port number.
Table 43: SRX110 Services Gateway 3G USB Modem Basic CLI Commands
Action
Command
Checks the status of the 3G USB modem.
show modem wireless interface cl-0/0/8
show interfaces terse
GSM
102
Unlocks the GSM SIM.
request modem wireless gsm sim-unlock cl-0/0/8
pin
Unlocks the SIM automatically on reboot.
set interfaces cl-0/0/ 8 cellular-options gsm-options
sim-unlock-code
Copyright © 2016, Juniper Networks, Inc.
Chapter 14: Performing Initial Configuration
Table 43: SRX110 Services Gateway 3G USB Modem Basic CLI
Commands (continued)
Action
Command
Recovers the SIM from the Pin Unlock Key
(PUK) state.
request modem wireless gsm sim-unblock cl-0/0/8
puk new-puk-number pin new-pin-number
When you attempt to unlock the SIM, if you
enter a wrong PIN three times in a row, the
SIM enters the PUK state.
NOTE: You must obtain the PUK value from your
cellular service provider.
Changes the PIN on the SIM.
request modem wireless gsm change-pin cl-0/0/8
old-pin current-pin-number new-pin new-pin-number
For more details on configuration examples, see the Junos OS Interfaces Configuration
Guide for Security Devices.
Related
Documentation
•
SRX110 Services Gateway 3G USB Modem Overview on page 10
•
Installing a 3G USB Modem in the SRX110 Services Gateway USB Port on page 67
•
SRX110 Services Gateway 3G-WAN USB Port Physical Specifications on page 32
Configuring the Integrated VDSL2 Interface on the SRX110 Services Gateway
To use J-Web to perform basic configuration for the integrated VDSL2 interface and to
configure network interfaces for the services gateway:
1.
In J-Web, select Configure>Interfaces.
The Interfaces page appears and lists the network interfaces present on the services
gateway, along with configuration information (if configured).
2. To configure properties for a network interface, select the interface name (pt-1/0/0),
and click Edit.
3. To use the VDSL2 port, you must assign it to a security zone other than the Null zone.
Optionally, you can also assign the port an IP address (for example, 192.168.3.1/24).
Enter or select the following settings:
a. Select Configure>Security>Zones/Screens.
b. Add or select a security zone other than Null; for example, Trust.
c. For host inbound traffic, set the following:
•
Copyright © 2016, Juniper Networks, Inc.
System Services=Allow All.
103
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
Protocols=Allow All.
d. Click OK to save changes, and click Commit to apply the configuration and other
pending changes.
4. To use the VDSL2 port (VDSL/ADSL-POTS or VDSL/ADSL-ISDN), you must also set
security policies. Select the following settings:
a. Select Configure>Security>Apply Policy.
b. Set Policy Action: Default Policy Action=Permit-All.
c. Click OK to save changes, and click Commit to apply the configuration and other
pending changes (if any).
For more information, in the J-Web user interface, select Configure>Interfaces, and click
Help.
To use the CLI to perform basic configuration of the integrated VDSL2 interface and to
configure network interfaces for the services gateway:
•
Verify that the VDSL2 interface is installed on the device:
show chassis hardware
•
Verify the status of the interface:
show interfaces terse
•
Assign the port an IP address:
set interface pt-1/0/0 unit 0 family inet address interface address/destination prefix
•
Add or select a security zone; for example, Zone1:
set security zones security-zone trust interfaces pt-1/0/0.0 host-inbound-traffic
system-services all
•
Add or select security zones for host inbound traffic option protocols:
set security zones security-zone trust interfaces pt-1/0/0.0 host-inbound-traffic protocols
all
•
Set security policies:
set security policies default-policy permit-all
For more details, see the Junos OS Interfaces Configuration Guide for Security Devices.
Related
Documentation
104
•
SRX110 Services Gateway Integrated VDSL2 Interface Overview on page 6
•
SRX110 Services Gateway Integrated VDSL2 Interface Key Features on page 6
•
SRX110 Services Gateway Integrated VDSL2 Interface LEDs on page 22
Copyright © 2016, Juniper Networks, Inc.
PART 4
Maintaining and Troubleshooting
Components
•
Maintaining Components on page 107
•
Troubleshooting Components on page 109
Copyright © 2016, Juniper Networks, Inc.
105
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
106
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 15
Maintaining Components
•
Maintaining the SRX110 Services Gateway Hardware Components on page 107
Maintaining the SRX110 Services Gateway Hardware Components
Table 44 on page 107 describes the common tasks to maintain the hardware components
of the services gateway.
Table 44: Maintenance Procedures for the Services Gateway Hardware
Components
Maintenance
Procedure
Description
Routine Maintenance
Procedures
To maintain optimum performance of the services gateway, you should
regularly perform the following preventive maintenance procedures:
Maintaining the Power
Supply
•
Inspect the installation site for moisture, loose wires or cables, and
excessive dust.
•
Make sure that airflow is unobstructed around the device and into
the air intake vents.
To maintain the power supply on the services gateway:
•
Make sure that the power and grounding cables are arranged so that
they do not obstruct access to other device components.
•
Periodically inspect the site to ensure that the grounding and power
cables connected to the device are securely in place and that there
is no moisture accumulating near the device.
CAUTION: We recommend using a surge protector for the power
connection.
Related
Documentation
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX110 Services
Gateway on page 34
Copyright © 2016, Juniper Networks, Inc.
107
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
108
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 16
Troubleshooting Components
•
Monitoring the SRX110 Services Gateway Chassis Using the CLI on page 109
•
Monitoring the SRX110 Services Gateway Components Using LEDs on page 110
•
Monitoring the SRX110 Services Gateway Using Chassis Alarm Conditions on page 112
•
Monitoring the SRX110 Services Gateway Power System on page 114
•
Resetting the SRX110 Services Gateway on page 114
•
Using the Reset Config Button on the SRX110 Services Gateway on page 115
•
Changing the Reset Config Button Behavior on the SRX110 Services Gateway on page 116
•
Juniper Networks Technical Assistance Center on page 117
Monitoring the SRX110 Services Gateway Chassis Using the CLI
You can monitor alarms to troubleshoot hardware problems on a services gateway. The
chassis properties include the status of active chassis alarms and environment
measurements on the device.
To view these chassis properties, select Monitor in the J-Web interface, or enter the
following CLI show commands:
•
show chassis hardware
•
show chassis hardware detail
•
show chassis environment
•
show chassis fpc
•
show chassis alarms
Examples
The following examples provide the sample output of commands:
For SRX110 Services Gateway (SRX110H-VA)
user@host >show chassis hardware
Hardware inventory:
Item
Version
Chassis
Copyright © 2016, Juniper Networks, Inc.
Part number
Serial number
AX0021AF0037
Description
SRX110h-va
109
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Routing Engine
FPC 0
PIC 0
FPC 1
PIC 0
Power Supply 0
REV 01
650-035910
AX0021AF0037
RE-SRX110H-VA
FPC
8x FE Base PIC
FPC
Internal VDSL2/ADSL-POTS
show chassis environment
user@host > show chassis environment
Class Item
Temp Routing Engine
Routing Engine CPU
Power Power Supply 0
Status
Measurement
OK
64 degrees C / 147 degrees F
Absent
OK
show chassis fpc
user@host >show chassis fpc
Slot State
0 Online
1 Online
Temp CPU Utilization (%)
Memory
Utilization (%)
(C) Total Interrupt
DRAM (MB) Heap
Buffer
-------------------- CPU less FPC --------------------------------------- CPU less FPC --------------------
show chassis alarms
user@host >show chassis alarms
No alarms currently active
Related
Documentation
•
Monitoring the SRX110 Services Gateway Using Chassis Alarm Conditions on page 112
•
Monitoring the SRX110 Services Gateway Components Using LEDs on page 110
•
Monitoring the SRX110 Services Gateway Power System on page 114
•
Maintaining the SRX110 Services Gateway Hardware Components on page 107
Monitoring the SRX110 Services Gateway Components Using LEDs
You can monitor the chassis condition by using the LEDs. Table 45 on page 111 lists the
LEDs, their condition, the possible causes and corrective actions.
110
Copyright © 2016, Juniper Networks, Inc.
Chapter 16: Troubleshooting Components
Table 45: Component LEDs on the Services Gateway
LED
State
Meaning
Possible Causes and
Corrective Actions
Status LED
Green
Indicates that the device is
functioning normally.
Normal condition. No action
is required.
Amber
•
The device is starting up.
•
The Reset Config button
is pressed.
Normal condition. No action
is required.
Alarm LED
Red
Indicates an error in the
device.
Contact the Juniper
Networks Technical
Assistance Center (JTAC).
See “Juniper Networks
Technical Assistance
Center” on page 117.
Green
Indicates that the device is
functioning normally.
Normal condition. No action
is required.
Red
The device indicates a critical
alarm.
A critical alarm indicates a
critical situation on the
gateway that requires
immediate action.
See “Monitoring the SRX110
Services Gateway Using
Chassis Alarm Conditions”
on page 112.
Amber
The device indicates a major
alarm.
A major alarm requires
monitoring or maintenance.
If left unchecked, it might
cause an interruption in
service or degradation in
performance.
See “Monitoring the SRX110
Services Gateway Using
Chassis Alarm Conditions”
on page 112.
Off
The device is starting up.
Normal condition. No action
is required.
NOTE: When the system is
up and running, if the Alarm
LED is off, it indicates that no
alarms are present on the
device.
Copyright © 2016, Juniper Networks, Inc.
111
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Table 45: Component LEDs on the Services Gateway (continued)
LED
State
Meaning
Possible Causes and
Corrective Actions
Power LED
Green
The device is receiving power
and is functioning normally.
Normal condition. No action
is required.
Amber
The Power button has been
pressed and quickly released.
Normal condition. No action
is required.
Off
The device is not receiving
power.
Normal condition if the
services gateway is
switched off. No action is
required.
If you have not powered off
the services gateway, verify
that the AC power cord
from the power source to
the device is not damaged,
the socket is in working
condition, and the device
has an AC input voltage
between 110 and 240 VAC.
See “Monitoring the SRX110
Services Gateway Power
System” on page 114.
Related
Documentation
•
Monitoring the SRX110 Services Gateway Using Chassis Alarm Conditions on page 112
•
Monitoring the SRX110 Services Gateway Chassis Using the CLI on page 109
•
Monitoring the SRX110 Services Gateway Power System on page 114
•
Maintaining the SRX110 Services Gateway Hardware Components on page 107
Monitoring the SRX110 Services Gateway Using Chassis Alarm Conditions
When the services gateway detects an alarm condition, the alarm LED on the front panel
turns red or amber as appropriate.
To view a more detailed description of the cause of the alarm , issue the show chassis
alarms CLI command.
For more information on the show chassis alarms command, see the following topics:
•
Initial Configuration for Security Devices
•
Monitoring and Troubleshooting for Security Devices
Table 46 on page 113 describes alarms that can occur for an SRX110 Services Gateway
chassis component.
112
Copyright © 2016, Juniper Networks, Inc.
Chapter 16: Troubleshooting Components
Table 46: SRX110 Services Gateway Chassis Alarm Conditions and
Corrective Actions
Component
Alarm Condition
Action
Boot media
The services gateway
boots from an alternate
boot device.
•
If the internal flash memory fails at
startup, the services gateway
automatically boots from the
alternative boot device (USB storage
device).
Alarm
Severity
Amber
(minor)
NOTE: If you configured your services
gateway to boot from an alternative
boot device, ignore this alarm condition.
•
Reformat the internal flash memory,
and install a bootable image. (See the
Initial Configuration for Security
Devices and the Monitoring and
Troubleshooting for Security
Devices.)
Hardware
components
on the
services
gateway
Related
Documentation
•
If you did not configure the services
gateway to boot from an alternative
boot device, contact Juniper Networks
Technical Assistance Center (JTAC).
See “Juniper Networks Technical
Assistance Center” on page 117.
The services gateway
chassis temperature or
chassis is too warm.
•
Check the room temperature. See
SRX110 Services Gateway Specifications.
•
Check the airflow. See “General Site
Guidelines for Installing the SRX110
Services Gateway” on page 30.
The services gateway
temperature is too high,
either because of an
internal overheating
condition or because
the maximum
recommended room
temperature has been
exceeded.
The services gateway shuts down
automatically in 4 minutes.
Amber
(minor)
Red
(major)
•
Monitoring the SRX110 Services Gateway Chassis Using the CLI on page 109
•
Monitoring the SRX110 Services Gateway Power System on page 114
•
Using the Reset Config Button on the SRX110 Services Gateway on page 115
•
Changing the Reset Config Button Behavior on the SRX110 Services Gateway on page 116
•
Juniper Networks Technical Assistance Center on page 117
Copyright © 2016, Juniper Networks, Inc.
113
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Monitoring the SRX110 Services Gateway Power System
The LEDs on the services gateway enable you to determine the performance and
operation. The Power LED, located on the front panel of the services gateway, indicates
the different settings with respect to the power system.
Table 47 on page 114 describes different Power LED status settings and their corrective
actions.
Table 47: Services Gateway Power LED Status
Related
Documentation
Status
Meaning
Possible Cause and Corrective Action
Green
The device is receiving power,
and the internal power supply
is functional.
Normal indication. No action is required.
Amber
The Power button has been
pressed and quickly released.
The device is shutting down or
starting up.
Normal indication. No action is required.
Off
The device is not receiving
power.
•
Verify that the AC power cord from the power
source to the device is not damaged. If the
insulation is cracked or broken, immediately replace
the cord or cable.
•
Ensure that the socket you plug in is in working
condition.
•
Ensure the device has an AC input voltage between
110 and 240 VAC.
•
If you cannot determine the cause of the problem
or need additional assistance, contact the Juniper
Networks Technical Assistance Center (JTAC). See
“Juniper Networks Technical Assistance Center”
on page 117.
•
Monitoring the SRX110 Services Gateway Components Using LEDs on page 110
•
Monitoring the SRX110 Services Gateway Chassis Using the CLI on page 109
•
Monitoring the SRX110 Services Gateway Using Chassis Alarm Conditions on page 112
•
Using the Reset Config Button on the SRX110 Services Gateway on page 115
•
Changing the Reset Config Button Behavior on the SRX110 Services Gateway on page 116
•
Juniper Networks Technical Assistance Center on page 117
Resetting the SRX110 Services Gateway
The Reset Config button on the front panel of the services gateway can be used to remove
the current configuration and reset the device to the default (factory) configuration. The
button is recessed in the front panel to prevent it from being pressed accidentally.
114
Copyright © 2016, Juniper Networks, Inc.
Chapter 16: Troubleshooting Components
NOTE: Pressing and holding the Reset Config button for 15 seconds or more
deletes all configurations on the device and loads and commits the default
(factory) configuration.
Related
Documentation
•
Powering On the SRX110 Services Gateway on page 80
•
Powering Off the SRX110 Services Gateway on page 81
•
Connecting the SRX110 Services Gateway to the Power Supply on page 79
•
Grounding the SRX110 Services Gateway on page 72
•
Using the Reset Config Button on the SRX110 Services Gateway on page 115
•
SRX110 Services Gateway Front Panel and Back Panel Views with 3G and Integrated
VDSL2
•
SRX110 Services Gateway LEDs
Using the Reset Config Button on the SRX110 Services Gateway
If a configuration fails or denies management access to the services gateway, you can
use the Reset Config button to restore the device to the factory-default configuration or
a rescue configuration. For example, if someone inadvertently commits a configuration
that denies management access to a services gateway, you can delete the invalid
configuration and replace it with a rescue configuration by pressing the Reset Config
button.
NOTE: The Reset Config button is recessed to prevent it from being pressed
accidentally.
The rescue configuration is a previously committed, valid configuration. You must have
previously set the rescue configuration through the J-Web interface or the CLI.
To press the Reset Config button, insert a small probe (such as a straightened paper
clip) into the pinhole on the front panel.
•
By default, pressing and quickly releasing the Reset Config button loads and commits
the rescue configuration through the J-Web interface or the CLI. The Status LED glows
amber during this time.
•
By default, pressing and holding the Reset Config button for 15 seconds or more—until
the Status LED glows amber—deletes all configurations on the device, including the
backup configurations and rescue configuration, and loads and commits the factory
configuration.
For details about factory-default settings, see the following topics:
•
Initial Configuration for Security Devices
Copyright © 2016, Juniper Networks, Inc.
115
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
Related
Documentation
Monitoring and Troubleshooting for Security Devices
•
Changing the Reset Config Button Behavior on the SRX110 Services Gateway on page 116
•
Monitoring the SRX110 Services Gateway Components Using LEDs on page 110
•
Monitoring the SRX110 Services Gateway Chassis Using the CLI on page 109
•
Monitoring the SRX110 Services Gateway Using Chassis Alarm Conditions on page 112
•
Monitoring the SRX110 Services Gateway Power System on page 114
•
Juniper Networks Technical Assistance Center on page 117
Changing the Reset Config Button Behavior on the SRX110 Services Gateway
You can change the default operation of the Reset Config button by limiting how the
button resets the services gateway:
•
To prevent the Reset Config button from setting the device to the factory-default
configuration and deleting all other configurations:
admin@host# set chassis config-button no-clear
You can still press and quickly release the button to reset it to the rescue configuration.
•
To prevent the Reset Config button from setting the device to the rescue configuration:
admin@host# set chassis config-button no-rescue
You can still press and hold the button for 15 seconds or more to reset the gateway to
the factory-default configuration.
•
To disable the button and prevent the device from resetting to either configuration:
admin@host# set chassis config-button no-clear no-rescue
The no-rescue option prevents the Reset Config button from loading the rescue
configuration. The no-clear option prevents the Reset Config button from deleting all
configurations on the services gateway.
To return the function of the Reset Config button to its default behavior, remove the
config-button statement from the device configuration.
Related
Documentation
116
•
Using the Reset Config Button on the SRX110 Services Gateway on page 115
•
Monitoring the SRX110 Services Gateway Components Using LEDs on page 110
•
Monitoring the SRX110 Services Gateway Chassis Using the CLI on page 109
•
Monitoring the SRX110 Services Gateway Using Chassis Alarm Conditions on page 112
•
Monitoring the SRX110 Services Gateway Power System on page 114
•
Juniper Networks Technical Assistance Center on page 117
Copyright © 2016, Juniper Networks, Inc.
Chapter 16: Troubleshooting Components
Juniper Networks Technical Assistance Center
If you need assistance while troubleshooting a services gateway, open a support case
using the Case Manager link at http://www.juniper.net/support/, or call 1-888-314-JTAC
(within the United States) or 1-408-745-9500 (from outside the United States).
Copyright © 2016, Juniper Networks, Inc.
117
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
118
Copyright © 2016, Juniper Networks, Inc.
PART 5
Replacing Components
•
Contacting Customer Support and Returning Components on page 121
Copyright © 2016, Juniper Networks, Inc.
119
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
120
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 17
Contacting Customer Support and
Returning Components
•
Contacting Customer Support on page 121
•
Return Procedure for the SRX110 Services Gateway on page 122
•
Locating the SRX110 Services Gateway Component Serial Number and Agency
Labels on page 123
•
Information You Might Need to Supply to Juniper Networks Technical Assistance
Center on page 124
•
Packing the SRX110 Services Gateway and Components for Shipment on page 125
Contacting Customer Support
Once you have located the serial numbers of the services gateway or component, you
can return them for repair or replacement. For this, you need to contact Juniper Networks
Technical Assistance Center (JTAC).
You can contact JTAC 24 hours a day, 7 days a week, using any of the following methods:
•
On the Web: Using the Case Manager link at http://www.juniper.net/support/
•
By telephone:
•
From the US and Canada: 1-888-314-JTAC
•
From all other locations: 1-408-745-9500
NOTE: If contacting JTAC by telephone, enter your 11-digit case number
followed by the pound (#) key if this is an existing case, or press the star
(*) key to be routed to the next available support engineer.
Related
Documentation
•
Return Procedure for the SRX110 Services Gateway on page 122
•
Locating the SRX110 Services Gateway Component Serial Number and Agency Labels
on page 123
•
Packing the SRX110 Services Gateway and Components for Shipment on page 125
Copyright © 2016, Juniper Networks, Inc.
121
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Information You Might Need to Supply to Juniper Networks Technical Assistance Center
on page 124
•
Return Procedure for the SRX110 Services Gateway
Follow the tasks list provided in Table 48 on page 122 to return an SRX110 Services Gateway
or component to Juniper Networks for repair or replacement:
Table 48: Return Procedure for SRX110 Services Gateway
Step
Task
For more information, see
1
Determine the part number and serial
number of the device or component.
“Locating the SRX110 Services
Gateway Component Serial Number
and Agency Labels” on page 123
2
Obtain a Return Materials Authorization
(RMA) number from JTAC.
“Information You Might Need to Supply
to Juniper Networks Technical
Assistance Center” on page 124
3
Pack the SRX110 Services Gateway or
component for shipping.
“Packing the SRX110 Services Gateway
and Components for Shipment” on
page 125
NOTE: Do not return the device or any component to Juniper Networks unless
you have first obtained an RMA number. Juniper Networks reserves the right
to refuse shipments that do not have an RMA. Refused shipments are returned
to the customer via collect freight.
For more information about return and repair policies, see the customer support webpage
at http://www.juniper.net/support/guidelines.html.
For product problems or technical support issues, open a support case using the Case
Manager link at http://www.juniper.net/support/ or call 1-888-314-JTAC (within the United
States) or 1-408-745-9500 (outside the United States).
Related
Documentation
122
•
Locating the SRX110 Services Gateway Component Serial Number and Agency Labels
on page 123
•
Information You Might Need to Supply to Juniper Networks Technical Assistance Center
on page 124
•
Contacting Customer Support on page 121
•
Packing the SRX110 Services Gateway and Components for Shipment on page 125
Copyright © 2016, Juniper Networks, Inc.
Chapter 17: Contacting Customer Support and Returning Components
Locating the SRX110 Services Gateway Component Serial Number and Agency Labels
This topic includes the following sections:
•
Listing the SRX110 Services Gateway and Component Details with the CLI on page 123
•
SRX110 Services Gateway Chassis Serial Number and Agency Labels on page 123
Listing the SRX110 Services Gateway and Component Details with the CLI
Before contacting Juniper Networks to request an RMA, you must find the serial number
on the SRX110 Services Gateway or component.
To list all of the SRX110 Services Gateway components and their serial numbers, enter
the following command-line interface (CLI) command:
For SRX110 Services Gateway (SRX110H-VA)
user@host> show chassis hardware
Hardware inventory:
Item
Version Part number
Chassis
Routing Engine
REV 01
650-035910
FPC 0
PIC 0
FPC 1
PIC 0
Serial number
AX0021AF0037
AX0021AF0037
Description
SRX110h-va
RE-SRX110H-VA
FPC
8x FE Base PIC
FPC
Internal VDSL2/ADSL-POTS
Power Supply 0
For SRX110 Services Gateway (SRX110H-VB)
user@host> show chassis hardware
Hardware inventory:
Item
Version Part number
Chassis
Routing Engine
REV 01
650-038184
FPC 0
PIC 0
FPC 1
PIC 0
Serial number
AY1111AF0004
AY1111AF0004
Description
SRX110h-vb
RE-SRX110H-VB
FPC
8x FE Base PIC
FPC
Internal VDSL2/ADSL-ISDN
Power Supply 0
NOTE: Most components also have a serial number ID label attached to the
component body.
SRX110 Services Gateway Chassis Serial Number and Agency Labels
The SRX110 Services Gateway has a serial number ID label and an agency label located
on the bottom of the chassis as shown in Figure 29 on page 124.
Copyright © 2016, Juniper Networks, Inc.
123
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
g033621
Figure 29: Location of SRX110 Serial Number and Agency Labels
Serial number
ID label
Related
Documentation
•
Packing the SRX110 Services Gateway and Components for Shipment on page 125
•
Contacting Customer Support on page 121
•
Return Procedure for the SRX110 Services Gateway on page 122
Information You Might Need to Supply to Juniper Networks Technical Assistance Center
If you are returning a services gateway or hardware component to Juniper Networks for
repair or replacement, obtain a Return Materials Authorization (RMA) number from
Juniper Networks Technical Assistance Center (JTAC).
When requesting support from JTAC by telephone, be prepared to provide the following
information:
Related
Documentation
124
•
Your existing case number, if you have one
•
Details of the failure or problem
•
Type of activity being performed on the services gateway when the problem occurred
•
Configuration data displayed by one or more show commands
•
Your name, organization name, telephone number, fax number, and shipping address
•
Return Procedure for the SRX110 Services Gateway on page 122
•
Locating the SRX110 Services Gateway Component Serial Number and Agency Labels
on page 123
•
Contacting Customer Support on page 121
Copyright © 2016, Juniper Networks, Inc.
Chapter 17: Contacting Customer Support and Returning Components
Packing the SRX110 Services Gateway and Components for Shipment
This topic includes the following sections:
•
Packing the Services Gateway on page 125
•
Packing the Components for Shipment on page 125
Packing the Services Gateway
To pack the services gateway for shipment:
1.
Retrieve the shipping carton and packing materials in which the device was originally
shipped. If you do not have these materials, contact your Juniper Networks
representative about approved packaging materials.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect
the strap to the ESD point on the chassis or to an outside ESD point if the device is
disconnected from earth ground.
3. On the console or other management device connected to the services gateway, enter
CLI operational mode and issue the following command to shut down the services
gateway software:
user@host> request system power-off
Wait until a message appears on the console confirming that the operating system
has halted.
4. Shut down power to the device by pressing the Power button on the front panel of
the device.
5. Disconnect power from the device.
6. Remove the cables that connect to all external devices.
7. If the device is installed on a wall or rack, have one person support the weight of the
device while another person unscrews and removes the mounting screws.
8. Place the device in the shipping carton.
9. Cover the device with an ESD bag, and place the packing foam on top of and around
the device.
10. Replace the accessory box on top of the packing foam.
11. Securely tape the box closed.
12. Write the Return Materials Authorization (RMA) number on the exterior of the box to
ensure proper tracking.
Packing the Components for Shipment
Follow these guidelines for packing and shipping individual components of the services
gateway:
Copyright © 2016, Juniper Networks, Inc.
125
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
When you return a component, make sure that it is adequately protected with packing
materials and packed so that the pieces are prevented from moving around inside the
carton.
•
Use the original shipping materials if they are available.
•
Write the Return Materials Authorization (RMA) number on the exterior of the box to
ensure proper tracking.
CAUTION: Do not stack any of the services gateway components during
packing.
Related
Documentation
126
•
Contacting Customer Support on page 121
•
Locating the SRX110 Services Gateway Component Serial Number and Agency Labels
on page 123
•
Return Procedure for the SRX110 Services Gateway on page 122
•
Information You Might Need to Supply to Juniper Networks Technical Assistance Center
on page 124
Copyright © 2016, Juniper Networks, Inc.
PART 6
Safety and Regulatory Compliance
Information
•
General Safety Guidelines and Warnings on page 129
•
Fire Safety Requirements on page 137
•
Installation Safety Guidelines and Warnings on page 139
•
Laser and LED Safety Guidelines and Warnings on page 145
•
Maintenance and Operational Safety Guidelines and Warnings on page 149
•
Electrical Safety Guidelines and Warnings on page 155
•
Agency Approvals and Regulatory Compliance Information on page 157
Copyright © 2016, Juniper Networks, Inc.
127
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
128
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 18
General Safety Guidelines and Warnings
•
SRX110 Services Gateway Definition of Safety Warning Levels on page 129
•
SRX110 Services Gateway General Safety Guidelines and Warnings on page 131
•
SRX110 Services Gateway Safety Requirements, Warnings, and Guidelines on page 135
SRX110 Services Gateway Definition of Safety Warning Levels
This topic defines the following four levels of safety warnings used in Juniper Networks
technical publications:
NOTE: You might find this information helpful in a particular situation or
might otherwise overlook it.
CAUTION: You need to observe the specified guidelines to avoid minor injury
or discomfort to you or severe damage to the services gateway.
WARNING: This symbol is used with laser warnings. Unterminated optical
connectors can emit invisible laser radiation. Focusing your eye directly on a
laser source—even a low-power laser—could permanently damage the eye.
WARNING: This symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for
preventing accidents.
Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in
een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige
apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische
schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard
maatregelen om ongelukken te voorkomen.
Copyright © 2016, Juniper Networks, Inc.
129
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi
johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa,
ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista
onnettomuuksien ehkäisykeinoista.
Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez
dans une situation pouvant causer des blessures ou des dommages corporels.
Avant de travailler sur un équipement, soyez conscient des dangers posés
par les circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents.
Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer
Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der
Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen
Stromkreisen verbundenen Gefahren und der Standardpraktiken zur
Vermeidung von Unfällen bewußt.
Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione
potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi
apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed
essere al corrente delle pratiche standard per la prevenzione di incidenti.
Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som
kan føre til personskade. Før du utfører arbeid på utstyr, må du vare
oppmerksom på de faremomentene som elektriske kretser innebærer, samt
gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.
Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que
lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer
equipamento, familiarize-se com os perigos relacionados com circuitos
eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis
acidentes.
¡Atención! Este símbolo de aviso significa peligro. Existe riesgo para su
integridad física. Antes de manipular cualquier equipo, considerar los riesgos
que entraña la corriente eléctrica y familiarizarse con los procedimientos
estándar de prevención de accidentes.
Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation
som kan leda till personskada. Innan du utför arbete på någon utrustning
måste du vara medveten om farorna med elkretsar och känna till vanligt
förfarande för att förebygga skador.
Related
Documentation
130
•
SRX110 Services Gateway General Safety Guidelines and Warnings on page 131
•
SRX110 Services Gateway Fire Safety Requirements on page 137
•
SRX110 Services Gateway Installation Safety Guidelines and Warnings on page 139
•
SRX110 Services Gateway Laser and LED Safety Guidelines and Warnings on page 145
Copyright © 2016, Juniper Networks, Inc.
Chapter 18: General Safety Guidelines and Warnings
•
SRX110 Services Gateway Electrical Safety Guidelines and Warnings on page 155
•
SRX110 Services Gateway Maintenance and Operational Safety Guidelines and Warnings
on page 149
SRX110 Services Gateway General Safety Guidelines and Warnings
General Safety Guidelines and Warnings
The following guidelines help ensure your safety and protect the services gateway from
damage. The list of guidelines might not address all potentially hazardous situations in
your working environment, so be alert and exercise good judgment at all times.
•
Perform only the procedures explicitly described in these topics. Ensure that only
authorized service personnel perform other system services.
•
Keep the area around the chassis clear and free from dust before, during, and after
installation.
•
Keep tools away from areas where people could trip on them.
•
Wear safety glasses if you are working under any conditions that could be hazardous
to your eyes.
•
Do not perform any actions that create a potential hazard to people or make the
equipment unsafe.
•
Never install or manipulate wiring during electrical storms.
•
Never install electrical jacks in wet locations unless the jacks are specifically designed
for wet environments.
•
Do not open or remove chassis covers or sheet metal parts unless instructions are
provided in this guide. Such an action could cause severe electrical shock.
•
Do not push or force any objects through any opening in the chassis frame. Such an
action could result in electrical shock or fire.
•
Avoid spilling liquid onto the services gateway chassis or onto any services gateway
component. Such an action could cause electrical shock or damage the services
gateway.
•
Avoid touching uninsulated electrical wires or terminals that have not been
disconnected from their power source. Such an action could cause electrical shock.
Qualified Personnel Warning
WARNING: Only trained and qualified personnel should install or replace the
services gateway.
Waarschuwing Installatie en reparaties mogen uitsluitend door getraind en
bevoegd personeel uitgevoerd worden.
Copyright © 2016, Juniper Networks, Inc.
131
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Varoitus Ainoastaan koulutettu ja pätevä henkilökunta saa asentaa tai vaihtaa
tämän laitteen.
Attention Tout installation ou remplacement de l'appareil doit être réalisé
par du personnel qualifié et compétent.
Warnung Gerät nur von geschultem, qualifiziertem Personal installieren oder
auswechseln lassen.
Avvertenza Solo personale addestrato e qualificato deve essere autorizzato
ad installare o sostituire questo apparecchio.
Advarsel Kun kvalifisert personell med riktig opplæring bør montere eller
bytte ut dette utstyret.
Aviso Este equipamento deverá ser instalado ou substituído apenas por
pessoal devidamente treinado e qualificado.
¡Atención! Estos equipos deben ser instalados y reemplazados
exclusivamente por personal técnico adecuadamente preparado y capacitado.
Varning! Denna utrustning ska endast installeras och bytas ut av utbildad
och kvalificerad personal.
Restricted Access Area Warning
WARNING: The services gateway is intended for installation in restricted
access areas. A restricted access area is an area to which access can be
gained only by service personnel through the use of a special tool, lock and
key, or other means of security, and which is controlled by the authority
responsible for the location.
Waarschuwing Dit toestel is bedoeld voor installatie op plaatsen met beperkte
toegang. Een plaats met beperkte toegang is een plaats waar toegang slechts
door servicepersoneel verkregen kan worden door middel van een speciaal
instrument, een slot en sleutel, of een ander veiligheidsmiddel, en welke
beheerd wordt door de overheidsinstantie die verantwoordelijk is voor de
locatie.
Varoitus Tämä laite on tarkoitettu asennettavaksi paikkaan, johon pääsy on
rajoitettua. Paikka, johon pääsy on rajoitettua, tarkoittaa paikkaa, johon vain
huoltohenkilöstö pääsee jonkin erikoistyökalun, lukkoon sopivan avaimen
tai jonkin muun turvalaitteen avulla ja joka on paikasta vastuussa olevien
toimivaltaisten henkilöiden valvoma.
Attention Cet appareil est à installer dans des zones d'accès réservé. Ces
dernières sont des zones auxquelles seul le personnel de service peut accéder
en utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout
132
Copyright © 2016, Juniper Networks, Inc.
Chapter 18: General Safety Guidelines and Warnings
autre moyen de sécurité. L'accès aux zones de sécurité est sous le contrôle
de l'autorité responsable de l'emplacement.
Warnung Diese Einheit ist zur Installation in Bereichen mit beschränktem
Zutritt vorgesehen. Ein Bereich mit beschränktem Zutritt ist ein Bereich, zu
dem nur Wartungspersonal mit einem Spezialwerkzeugs, Schloß und
Schlüssel oder anderer Sicherheitsvorkehrungen Zugang hat, und der von
dem für die Anlage zuständigen Gremium kontrolliert wird.
Avvertenza Questa unità deve essere installata in un'area ad accesso limitato.
Un'area ad accesso limitato è un'area accessibile solo a personale di
assistenza tramite un'attrezzo speciale, lucchetto, o altri dispositivi di
sicurezza, ed è controllata dall'autorità responsabile della zona.
Advarsel Denne enheten er laget for installasjon i områder med begrenset
adgang. Et område med begrenset adgang gir kun adgang til servicepersonale
som bruker et spesielt verktøy, lås og nøkkel, eller en annen
sikkerhetsanordning, og det kontrolleres av den autoriteten som er ansvarlig
for området.
Aviso Esta unidade foi concebida para instalação em áreas de acesso restrito.
Uma área de acesso restrito é uma área à qual apenas tem acesso o pessoal
de serviço autorizado, que possua uma ferramenta, chave e fechadura
especial, ou qualquer outra forma de segurança. Esta área é controlada pela
autoridade responsável pelo local.
¡Atención! Esta unidad ha sido diseñada para instalarse en áreas de acceso
restringido. Área de acceso restringido significa un área a la que solamente
tiene acceso el personal de servicio mediante la utilización de una herramienta
especial, cerradura con llave, o algún otro medio de seguridad, y que está
bajo el control de la autoridad responsable del local.
Varning! Denna enhet är avsedd för installation i områden med begränsat
tillträde. Ett område med begränsat tillträde får endast tillträdas av
servicepersonal med ett speciellt verktyg, lås och nyckel, eller annan
säkerhetsanordning, och kontrolleras av den auktoritet som ansvarar för
området.
Preventing Electrostatic Discharge Damage to the Services Gateway
Copyright © 2016, Juniper Networks, Inc.
133
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Many services gateway hardware components are sensitive to damage from static
electricity. Some components can be impaired by voltages as low as 30 V. You can easily
generate potentially damaging static voltages whenever you handle plastic or foam
packing material or if you move components across plastic or carpets. Observe the
following guidelines to minimize the potential for electrostatic discharge (ESD) damage,
which can cause intermittent or complete component failures:
•
Always use an ESD wrist strap or ankle strap, and verify that it is in direct contact with
your skin.
CAUTION: For safety, periodically check the resistance value of the ESD
strap. The measurement should be in the range of 1 to 10 Mohms.
•
When handling any component that is removed from the chassis, verify that the
equipment end of your ESD strap is attached to one of the ESD points on the chassis.
•
Avoid contact between the component and your clothing. ESD voltages emitted from
clothing can damage components.
•
When removing or installing a component, always place it component-side up on an
antistatic surface, in an antistatic card rack, or in an electrostatic bag. If you are returning
a component, place it into an electrostatic bag before packing it. See
Figure 30 on page 134.
Figure 30: Placing a Component into an Electrostatic Bag
Related
Documentation
134
•
SRX110 Services Gateway Definition of Safety Warning Levels on page 129
•
SRX110 Services Gateway Fire Safety Requirements on page 137
Copyright © 2016, Juniper Networks, Inc.
Chapter 18: General Safety Guidelines and Warnings
SRX110 Services Gateway Safety Requirements, Warnings, and Guidelines
To avoid harm to yourself or the device as you install and maintain it, follow the guidelines
for working with and near electrical equipment, as well as the safety procedures for
working with devices. For a discussion of how to make the installation site a safe
environment and a list of safety warnings, see “SRX110 Services Gateway Definition of
Safety Warning Levels” on page 129.
NOTE: Providing an exhaustive set of guidelines for working with electrical
equipment is beyond the scope of this guide.
Related
Documentation
•
General Site Guidelines for Installing the SRX110 Services Gateway on page 30
•
Required Tools and Parts for Installing and Maintaining the SRX110 Services Gateway
on page 48
•
Preparing the SRX110 Services Gateway for Rack-Mount, Desk-Mount, and Wall-Mount
Installation
Copyright © 2016, Juniper Networks, Inc.
135
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
136
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 19
Fire Safety Requirements
•
SRX110 Services Gateway Fire Safety Requirements on page 137
SRX110 Services Gateway Fire Safety Requirements
In the event of a fire emergency involving devices and other network equipment, the
safety of people is the primary concern. Establish procedures for protecting people in
the event of a fire emergency, provide safety training, and properly provision fire-control
equipment and fire extinguishers.
In addition, establish procedures to protect your equipment in the event of a fire
emergency. Juniper Networks products should be installed in an environment suitable
for electronic equipment. We recommend that fire suppression equipment be available
in the event of a fire in the vicinity of the equipment and that all local fire, safety, and
electrical codes and ordinances be observed when installing and operating your
equipment.
In the event of an electrical hazard or an electrical fire, first turn power off to the equipment
at the source. Then use a Type C fire extinguisher to extinguish the fire. Type C fire
extinguishers, which use noncorrosive fire retardants such as carbon dioxide (CO ) and
2
Halotron, are most effective for suppressing electrical fires. Type C fire extinguishers
displace the oxygen from the point of combustion to eliminate the fire. For extinguishing
fire on or around equipment that draws air from the environment for cooling, use this
type of inert oxygen displacement extinguisher instead of an extinguisher that leaves
residue on equipment.
Do not use multipurpose Type ABC chemical fire extinguishers (dry chemical fire
extinguishers) near Juniper Networks equipment. The primary ingredient in these fire
extinguishers is monoammonium phosphate, which is very sticky and difficult to clean.
In addition, in minute amounts of moisture, monoammonium phosphate can become
highly corrosive and corrodes most metals.
Any equipment in a room in which a chemical fire extinguisher has been discharged is
subject to premature failure and unreliable operation. The equipment is considered to
be irreparably damaged.
Copyright © 2016, Juniper Networks, Inc.
137
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
NOTE: To keep warranties effective, do not use a dry chemical fire extinguisher
to control a fire at or near a Juniper Networks services gateway. If a dry
chemical fire extinguisher is used, the unit is no longer eligible for coverage
under a service agreement.
We recommend that you dispose of any irreparably damaged equipment in an
environmentally responsible manner.
Related
Documentation
138
•
SRX110 Services Gateway General Safety Guidelines and Warnings on page 131
•
SRX110 Services Gateway Installation Safety Guidelines and Warnings on page 139
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 20
Installation Safety Guidelines and
Warnings
•
SRX110 Services Gateway Installation Safety Guidelines and Warnings on page 139
SRX110 Services Gateway Installation Safety Guidelines and Warnings
Installation Instructions Warning
WARNING: Read the installation instructions before you connect the services
gateway to a power source.
Waarschuwing Raadpleeg de installatie-aanwijzingen voordat u het systeem
met de voeding verbindt.
Varoitus Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Attention Avant de brancher le système sur la source d'alimentation, consulter
les directives d'installation.
Warnung Lesen Sie die Installationsanweisungen, bevor Sie das System an
die Stromquelle anschließen.
Avvertenza Consultare le istruzioni di installazione prima di collegare il sistema
all'alimentatore.
Advarsel Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Aviso Leia as instruções de instalação antes de ligar o sistema à sua fonte
de energia.
¡Atención! Ver las instrucciones de instalación antes de conectar el sistema
a la red de alimentación.
Varning! Läs installationsanvisningarna innan du kopplar systemet till dess
strömförsörjningsenhet.
Rack-Mounting Requirements and Warnings
Copyright © 2016, Juniper Networks, Inc.
139
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Ensure that the equipment rack into which the services gateway is installed is evenly and
securely supported to avoid the hazardous condition that could result from uneven
mechanical loading.
WARNING: To prevent bodily injury when mounting or servicing the services
gateway in a rack, take the following precautions to ensure that the system
remains stable. The following directives help maintain your safety:
•
The services gateway must be installed into a rack that is secured to the
building structure.
•
The services gateway should be mounted at the bottom of the rack if it is
the only unit in the rack.
•
When mounting the services gateway in a partially filled rack, load the rack
from the bottom to the top with the heaviest component at the bottom of
the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the services gateway in the rack.
Waarschuwing Om lichamelijk letsel te voorkomen wanneer u dit toestel in
een rek monteert of het daar een servicebeurt geeft, moet u speciale
voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel stabiel
blijft. De onderstaande richtlijnen worden verstrekt om uw veiligheid te
verzekeren:
•
De Juniper Networks services gateway moet in een stellage worden
geïnstalleerd die aan een bouwsel is verankerd.
•
Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel
het enige in het rek is.
•
Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het
rek van onderen naar boven te laden met het zwaarste onderdeel onderaan
in het rek.
•
Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de
stabilisatoren te monteren voordat u het toestel in het rek monteert of het
daar een servicebeurt geeft.
Varoitus Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineessä,
on noudatettava erityisiä varotoimia järjestelmän vakavuuden säilyttämiseksi,
jotta vältytään loukkaantumiselta. Noudata seuraavia turvallisuusohjeita:
140
•
Juniper Networks services gateway on asennettava telineeseen, joka on
kiinnitetty rakennukseen.
•
Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan.
Copyright © 2016, Juniper Networks, Inc.
Chapter 20: Installation Safety Guidelines and Warnings
•
Jos laite asetetaan osaksi täytettyyn telineeseen, aloita kuormittaminen
sen alaosasta kaikkein raskaimmalla esineellä ja siirry sitten sen yläosaan.
•
Jos telinettä varten on vakaimet, asenna ne ennen laitteen asettamista
telineeseen tai sen huoltamista siinä.
Attention Pour éviter toute blessure corporelle pendant les opérations de
montage ou de réparation de cette unité en casier, il convient de prendre des
précautions spéciales afin de maintenir la stabilité du système. Les directives
ci-dessous sont destinées à assurer la protection du personnel:
•
Le rack sur lequel est monté le Juniper Networks services gateway doit être
fixé à la structure du bâtiment.
•
Si cette unité constitue la seule unité montée en casier, elle doit être placée
dans le bas.
•
Si cette unité est montée dans un casier partiellement rempli, charger le
casier de bas en haut en plaçant l'élément le plus lourd dans le bas.
•
Si le casier est équipé de dispositifs stabilisateurs, installer les stabilisateurs
avant de monter ou de réparer l'unité en casier.
Warnung Zur Vermeidung von Körperverletzung beim Anbringen oder Warten
dieser Einheit in einem Gestell müssen Sie besondere Vorkehrungen treffen,
um sicherzustellen, daß das System stabil bleibt. Die folgenden Richtlinien
sollen zur Gewährleistung Ihrer Sicherheit dienen:
•
Der Juniper Networks services gateway muß in einem Gestell installiert
werden, das in der Gebäudestruktur verankert ist.
•
Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell
angebracht werden.
•
Bei Anbringung dieser Einheit in einem zum Teil gefüllten Gestell ist das
Gestell von unten nach oben zu laden, wobei das schwerste Bauteil unten
im Gestell anzubringen ist.
•
Wird das Gestell mit Stabilisierungszubehör geliefert, sind zuerst die
Stabilisatoren zu installieren, bevor Sie die Einheit im Gestell anbringen
oder sie warten.
Avvertenza Per evitare infortuni fisici durante il montaggio o la manutenzione
di questa unità in un supporto, occorre osservare speciali precauzioni per
garantire che il sistema rimanga stabile. Le seguenti direttive vengono fornite
per garantire la sicurezza personale:
Copyright © 2016, Juniper Networks, Inc.
•
Il Juniper Networks services gateway deve essere installato in un telaio, il
quale deve essere fissato alla struttura dell'edificio.
•
Questa unità deve venire montata sul fondo del supporto, se si tratta
dell'unica unità da montare nel supporto.
141
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
Quando questa unità viene montata in un supporto parzialmente pieno,
caricare il supporto dal basso all'alto, con il componente più pesante
sistemato sul fondo del supporto.
•
Se il supporto è dotato di dispositivi stabilizzanti, installare tali dispositivi
prima di montare o di procedere alla manutenzione dell'unità nel supporto.
Advarsel Unngå fysiske skader under montering eller reparasjonsarbeid på
denne enheten når den befinner seg i et kabinett. Vær nøye med at systemet
er stabilt. Følgende retningslinjer er gitt for å verne om sikkerheten:
•
Juniper Networks services gateway må installeres i et stativ som er forankret
til bygningsstrukturen.
•
Denne enheten bør monteres nederst i kabinettet hvis dette er den eneste
enheten i kabinettet.
•
Ved montering av denne enheten i et kabinett som er delvis fylt, skal
kabinettet lastes fra bunnen og opp med den tyngste komponenten nederst
i kabinettet.
•
Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene
installeres før montering eller utføring av reparasjonsarbeid på enheten i
kabinettet.
Aviso Para se prevenir contra danos corporais ao montar ou reparar esta
unidade numa estante, deverá tomar precauções especiais para se certificar
de que o sistema possui um suporte estável. As seguintes directrizes
ajudá-lo-ão a efectuar o seu trabalho com segurança:
•
O Juniper Networks services gateway deverá ser instalado numa prateleira
fixa à estrutura do edificio.
•
Esta unidade deverá ser montada na parte inferior da estante, caso seja
esta a única unidade a ser montada.
•
Ao montar esta unidade numa estante parcialmente ocupada, coloque os
itens mais pesados na parte inferior da estante, arrumando-os de baixo
para cima.
•
Se a estante possuir um dispositivo de estabilização, instale-o antes de
montar ou reparar a unidade.
¡Atención! Para evitar lesiones durante el montaje de este equipo sobre un
bastidor, o posteriormente durante su mantenimiento, se debe poner mucho
cuidado en que el sistema quede bien estable. Para garantizar su seguridad,
proceda según las siguientes instrucciones:
142
•
El Juniper Networks services gateway debe instalarse en un bastidor fijado
a la estructura del edificio.
•
Colocar el equipo en la parte inferior del bastidor, cuando sea la única
unidad en el mismo.
Copyright © 2016, Juniper Networks, Inc.
Chapter 20: Installation Safety Guidelines and Warnings
•
Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado,
comenzar la instalación desde la parte inferior hacia la superior colocando
el equipo más pesado en la parte inferior.
•
Si el bastidor dispone de dispositivos estabilizadores, instalar éstos antes
de montar o proceder al mantenimiento del equipo instalado en el bastidor.
Varning! För att undvika kroppsskada när du installerar eller utför
underhållsarbete på denna enhet på en ställning måste du vidta särskilda
försiktighetsåtgärder för att försäkra dig om att systemet står stadigt. Följande
riktlinjer ges för att trygga din säkerhet:
Related
Documentation
•
Juniper Networks services gateway måste installeras i en ställning som är
förankrad i byggnadens struktur.
•
Om denna enhet är den enda enheten på ställningen skall den installeras
längst ned på ställningen.
•
Om denna enhet installeras på en delvis fylld ställning skall ställningen
fyllas nedifrån och upp, med de tyngsta enheterna längst ned på ställningen.
•
Om ställningen är försedd med stabiliseringsdon skall dessa monteras fast
innan enheten installeras eller underhålls på ställningen.
•
SRX110 Services Gateway Fire Safety Requirements on page 137
•
SRX110 Services Gateway Laser and LED Safety Guidelines and Warnings on page 145
Copyright © 2016, Juniper Networks, Inc.
143
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
144
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 21
Laser and LED Safety Guidelines and
Warnings
•
SRX110 Services Gateway Laser and LED Safety Guidelines and Warnings on page 145
SRX110 Services Gateway Laser and LED Safety Guidelines and Warnings
•
General Laser Safety Guidelines on page 145
•
Class 1 Laser Product Warning on page 145
•
Class 1 LED Product Warning on page 146
•
Laser Beam Warning on page 146
•
Radiation from Open Port Apertures Warning on page 147
General Laser Safety Guidelines
When working around devices, observe the following safety guidelines to prevent eye
injury:
•
Do not look into unterminated ports or at fibers that connect to unknown sources.
•
Do not examine unterminated optical ports with optical instruments.
•
Avoid direct exposure to the beam.
WARNING: Unterminated optical connectors can emit invisible laser
radiation. The lens in the human eye focuses all the laser power on the
retina, so focusing the eye directly on a laser source—even a low-power
laser—could permanently damage the eye.
Class 1 Laser Product Warning
WARNING: Class 1 laser product.
Waarschuwing Klasse-1 laser produkt.
Varoitus Luokan 1 lasertuote.
Copyright © 2016, Juniper Networks, Inc.
145
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Attention Produit laser de classe I.
Warnung Laserprodukt der Klasse 1.
Avvertenza Prodotto laser di Classe 1.
Advarsel Laserprodukt av klasse 1.
Aviso Produto laser de classe 1.
¡Atención! Producto láser Clase I.
Varning! Laserprodukt av klass 1.
Class 1 LED Product Warning
WARNING: Class 1 LED product.
Waarschuwing Klasse 1 LED-product.
Varoitus Luokan 1 valodiodituote.
Attention Alarme de produit LED Class I.
Warnung Class 1 LED-Produktwarnung.
Avvertenza Avvertenza prodotto LED di Classe 1.
Advarsel LED-produkt i klasse 1.
Aviso Produto de classe 1 com LED.
¡Atención! Aviso sobre producto LED de Clase 1.
Varning! Lysdiodprodukt av klass 1.
Laser Beam Warning
WARNING: Do not stare into the laser beam or view it directly with optical
instruments.
Waarschuwing Niet in de straal staren of hem rechtstreeks bekijken met
optische instrumenten.
Varoitus Älä katso säteeseen äläkä tarkastele sitä suoraan optisen laitteen
avulla.
Attention Ne pas fixer le faisceau des yeux, ni l'observer directement à l'aide
d'instruments optiques.
146
Copyright © 2016, Juniper Networks, Inc.
Chapter 21: Laser and LED Safety Guidelines and Warnings
Warnung Nicht direkt in den Strahl blicken und ihn nicht direkt mit optischen
Geräten prüfen.
Avvertenza Non fissare il raggio con gli occhi né usare strumenti ottici per
osservarlo direttamente.
Advarsel Stirr eller se ikke direkte p strlen med optiske instrumenter.
Aviso Não olhe fixamente para o raio, nem olhe para ele directamente com
instrumentos ópticos.
¡Atención! No mirar fijamente el haz ni observarlo directamente con
instrumentos ópticos.
Varning! Rikta inte blicken in mot strålen och titta inte direkt på den genom
optiska instrument.
Radiation from Open Port Apertures Warning
WARNING: Because invisible radiation may be emitted from the aperture of
the port when no fiber cable is connected, avoid exposure to radiation and
do not stare into open apertures.
Waarschuwing Aangezien onzichtbare straling vanuit de opening van de
poort kan komen als er geen fiberkabel aangesloten is, dient blootstelling
aan straling en het kijken in open openingen vermeden te worden.
Varoitus Koska portin aukosta voi emittoitua näkymätöntä säteilyä, kun
kuitukaapelia ei ole kytkettynä, vältä säteilylle altistumista äläkä katso
avoimiin aukkoihin.
Attention Des radiations invisibles à l'il nu pouvant traverser l'ouverture du
port lorsqu'aucun câble en fibre optique n'y est connecté, il est recommandé
de ne pas regarder fixement l'intérieur de ces ouvertures.
Warnung Aus der Port-Öffnung können unsichtbare Strahlen emittieren,
wenn kein Glasfaserkabel angeschlossen ist. Vermeiden Sie es, sich den
Strahlungen auszusetzen, und starren Sie nicht in die Öffnungen!
Avvertenza Quando i cavi in fibra non sono inseriti, radiazioni invisibili possono
essere emesse attraverso l'apertura della porta. Evitate di esporvi alle
radiazioni e non guardate direttamente nelle aperture.
Advarsel Unngå utsettelse for stråling, og stirr ikke inn i åpninger som er åpne,
fordi usynlig stråling kan emiteres fra portens åpning når det ikke er tilkoblet
en fiberkabel.
Aviso Dada a possibilidade de emissão de radiação invisível através do orifício
da via de acesso, quando esta não tiver nenhum cabo de fibra conectado,
Copyright © 2016, Juniper Networks, Inc.
147
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
deverá evitar a exposição à radiação e não deverá olhar fixamente para
orifícios que se encontrarem a descoberto.
¡Atención! Debido a que la apertura del puerto puede emitir radiación invisible
cuando no existe un cable de fibra conectado, evite mirar directamente a las
aperturas para no exponerse a la radiación.
Varning! Osynlig strålning kan avges från en portöppning utan ansluten
fiberkabel och du bör därför undvika att bli utsatt för strålning genom att inte
stirra in i oskyddade öppningar.
Related
Documentation
148
•
SRX110 Services Gateway Installation Safety Guidelines and Warnings on page 139
•
SRX110 Services Gateway Maintenance and Operational Safety Guidelines and Warnings
on page 149
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 22
Maintenance and Operational Safety
Guidelines and Warnings
•
SRX110 Services Gateway Maintenance and Operational Safety Guidelines and
Warnings on page 149
SRX110 Services Gateway Maintenance and Operational Safety Guidelines and Warnings
This topic includes the following section:
•
Safety Guidelines and Warnings on page 149
Safety Guidelines and Warnings
Battery Handling Warning
WARNING: Replacing the battery incorrectly might result in an explosion.
Replace the battery only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
Waarschuwing Er is ontploffingsgevaar als de batterij verkeerd vervangen
wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat
door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig
fabrieksvoorschriften weggeworpen te worden.
Varoitus Räjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä
vaihtamiseen ainoastaan saman- tai vastaavantyyppistä akkua, joka on
valmistajan suosittelema. Hävitä käytetyt akut valmistajan ohjeiden mukaan.
Attention Danger d'explosion si la pile n'est pas remplacée correctement.
Ne la remplacer que par une pile de type semblable ou équivalent,
recommandée par le fabricant. Jeter les piles usagées conformément aux
instructions du fabricant.
Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr.
Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller
empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den
Anweisungen des Herstellers.
Copyright © 2016, Juniper Networks, Inc.
149
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Avvertenza Pericolo di esplosione se la batteria non è installata
correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata
dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.
Advarsel Det kan være fare for eksplosjon hvis batteriet skiftes på feil måte.
Skift kun med samme eller tilsvarende type som er anbefalt av produsenten.
Kasser brukte batterier i henhold til produsentens instruksjoner.
Aviso Existe perigo de explosão se a bateria for substituída incorrectamente.
Substitua a bateria por uma bateria igual ou de um tipo equivalente
recomendado pelo fabricante. Destrua as baterias usadas conforme as
instruções do fabricante.
¡Atención! Existe peligro de explosión si la batería se reemplaza de manera
incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el
equivalente recomendado por el fabricante. Desechar las baterías gastadas
según las instrucciones del fabricante.
Varning! Explosionsfara vid felaktigt batteribyte. Ersätt endast batteriet med
samma batterityp som rekommenderas av tillverkaren eller motsvarande.
Följ tillverkarens anvisningar vid kassering av använda batterier.
Jewelry Removal Warning
WARNING: Before working on equipment that is connected to power lines,
remove jewelry, including rings, necklaces, and watches. Metal objects heat
up when connected to power and ground and can cause serious burns or
weld the metal object to the terminals.
Waarschuwing Alvorens aan apparatuur te werken die met elektrische
leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges)
verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en
aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het
metalen voorwerp aan de aansluitklemmen lassen.
Varoitus Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden
parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien).
Metalliesineet kuumenevat, kun ne ovat yhteydessä sähkövirran ja maan
kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet
kiinni liitäntänapoihin.
Attention Avant d'accéder à cet équipement connecté aux lignes électriques,
ôter tout bijou (anneaux, colliers et montres compris). Lorsqu'ils sont branchés
à l'alimentation et reliés à la terre, les objets métalliques chauffent, ce qui
peut provoquer des blessures graves ou souder l'objet métallique aux bornes.
Warnung Vor der Arbeit an Geräten, die an das Netz angeschlossen sind,
jeglichen Schmuck (einschließlich Ringe, Ketten und Uhren) abnehmen.
150
Copyright © 2016, Juniper Networks, Inc.
Chapter 22: Maintenance and Operational Safety Guidelines and Warnings
Metallgegenstände erhitzen sich, wenn sie an das Netz und die Erde
angeschlossen werden, und können schwere Verbrennungen verursachen
oder an die Anschlußklemmen angeschweißt werden.
Avvertenza Prima di intervenire su apparecchiature collegate alle linee di
alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti
ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti
di alimentazione e massa: possono causare ustioni gravi oppure il metallo
può saldarsi ai terminali.
Advarsel Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du
skal arbeide på utstyr som er koblet til kraftledninger. Metallgjenstander som
er koblet til kraftledninger og jord blir svært varme og kan forårsake alvorlige
brannskader eller smelte fast til polene.
Aviso Antes de trabalhar em equipamento que esteja ligado a linhas de
corrente, retire todas as jóias que estiver a usar (incluindo anéis, fios e
relógios). Os objectos metálicos aquecerão em contacto com a corrente e
em contacto com a ligação à terra, podendo causar queimaduras graves ou
ficarem soldados aos terminais.
¡Atención! Antes de operar sobre equipos conectados a líneas de
alimentación, quitarse las joyas (incluidos anillos, collares y relojes). Los
objetos de metal se calientan cuando se conectan a la alimentación y a tierra,
lo que puede ocasionar quemaduras graves o que los objetos metálicos
queden soldados a los bornes.
Varning! Tag av alla smycken (inklusive ringar, halsband och armbandsur)
innan du arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt
hettas upp när de kopplas ihop med ström och jord och kan förorsaka
allvarliga brännskador; metallobjekt kan också sammansvetsas med
kontakterna.
Lightning Activity Warning
WARNING: Do not work on the system or connect or disconnect cables during
periods of lightning activity.
Waarschuwing Tijdens onweer dat gepaard gaat met bliksem, dient u niet
aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Varoitus Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota
kaapeleita ukkosilmalla.
Attention Ne pas travailler sur le système ni brancher ou débrancher les
câbles pendant un orage.
Warnung Arbeiten Sie nicht am System und schließen Sie keine Kabel an
bzw. trennen Sie keine ab, wenn es gewittert.
Copyright © 2016, Juniper Networks, Inc.
151
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Avvertenza Non lavorare sul sistema o collegare oppure scollegare i cavi
durante un temporale con fulmini.
Advarsel Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet
når det tordner eller lyner.
Aviso Não trabalhe no sistema ou ligue e desligue cabos durante períodos
de mau tempo (trovoada).
¡Atención! No operar el sistema ni conectar o desconectar cables durante el
transcurso de descargas eléctricas en la atmósfera.
Varning! Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller
koppla loss kablar.
Operating Temperature Warning
WARNING: To prevent the services gateway from overheating, do not operate
it in an area that exceeds the maximum recommended ambient temperature
ο
ο
of 104 F (40 C). To prevent airflow restriction, allow at least 6 in. (15.2 cm)
of clearance around the ventilation openings.
Waarschuwing Om te voorkomen dat welke services gateway van de Juniper
Networks services gateway dan ook oververhit raakt, dient u deze niet te
bedienen op een plaats waar de maximale aanbevolen
ο
omgevingstemperatuur van 40 C wordt overschreden. Om te voorkomen
dat de luchtstroom wordt beperkt, dient er minstens 15,2 cm speling rond de
ventilatie-openingen te zijn.
Varoitus Ettei Juniper Networks services gateway-sarjan reititin ylikuumentuisi,
sitä ei saa käyttää tilassa, jonka lämpötila ylittää korkeimman suositellun
ο
ympäristölämpötilan 40 C. Ettei ilmanvaihto estyisi, tuuletusaukkojen
ympärille on jätettävä ainakin 15,2 cm tilaa.
Attention Pour éviter toute surchauffe des routeurs de la gamme Juniper
Networks services gateway, ne l'utilisez pas dans une zone où la température
ο
ambiante est supérieure à 40 C. Pour permettre un flot d'air constant, dégagez
un espace d'au moins 15,2 cm autour des ouvertures de ventilations.
Warnung Um einen services gateway der services gateway vor Überhitzung
zu schützen, darf dieser nicht in einer Gegend betrieben werden, in der die
ο
Umgebungstemperatur das empfohlene Maximum von 40 C überschreitet.
Um Lüftungsverschluß zu verhindern, achten Sie darauf, daß mindestens
15,2 cm lichter Raum um die Lüftungsöffnungen herum frei bleibt.
Avvertenza Per evitare il surriscaldamento dei services gateway, non
adoperateli in un locale che ecceda la temperatura ambientale massima di
152
Copyright © 2016, Juniper Networks, Inc.
Chapter 22: Maintenance and Operational Safety Guidelines and Warnings
ο
40 C. Per evitare che la circolazione dell'aria sia impedita, lasciate uno spazio
di almeno 15.2 cm di fronte alle aperture delle ventole.
Advarsel Unngå overoppheting av eventuelle rutere i Juniper Networks
services gateway Disse skal ikke brukes på steder der den anbefalte
ο
ο
maksimale omgivelsestemperaturen overstiger 40 C (104 F). Sørg for at
klaringen rundt lufteåpningene er minst 15,2 cm (6 tommer) for å forhindre
nedsatt luftsirkulasjon.
Aviso Para evitar o sobreaquecimento do encaminhador Juniper Networks
services gateway, não utilize este equipamento numa área que exceda a
ο
temperatura máxima recomendada de 40 C. Para evitar a restrição à
circulação de ar, deixe pelo menos um espaço de 15,2 cm à volta das aberturas
de ventilação.
¡Atención! Para impedir que un encaminador de la serie Juniper Networks
services gateway se recaliente, no lo haga funcionar en un área en la que se
ο
supere la temperatura ambiente máxima recomendada de 40 C. Para impedir
la restricción de la entrada de aire, deje un espacio mínimo de 15,2 cm
alrededor de las aperturas para ventilación.
Varning! Förhindra att en Juniper Networks services gateway överhettas
genom att inte använda den i ett område där den maximalt rekommenderade
ο
omgivningstemperaturen på 40 C överskrids. Förhindra att luftcirkulationen
inskränks genom att se till att det finns fritt utrymme på minst 15,2 cm omkring
ventilationsöppningarna.
Product Disposal Warning
WARNING: Disposal of this product must be handled according to all national
laws and regulations.
Waarschuwing Dit produkt dient volgens alle landelijke wetten en
voorschriften te worden afgedankt.
Varoitus Tämän tuotteen lopullisesta hävittämisestä tulee huolehtia kaikkia
valtakunnallisia lakeja ja säännöksiä noudattaen.
Attention La mise au rebut définitive de ce produit doit être effectuée
conformément à toutes les lois et réglementations en vigueur.
Warnung Dieses Produkt muß den geltenden Gesetzen und Vorschriften
entsprechend entsorgt werden.
Avvertenza L'eliminazione finale di questo prodotto deve essere eseguita
osservando le normative italiane vigenti in materia
Advarsel Endelig disponering av dette produktet må skje i henhold til nasjonale
lover og forskrifter.
Copyright © 2016, Juniper Networks, Inc.
153
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Aviso A descartagem final deste produto deverá ser efectuada de acordo
com os regulamentos e a legislação nacional.
¡Atención! El desecho final de este producto debe realizarse según todas las
leyes y regulaciones nacionales
Varning! Slutlig kassering av denna produkt bör skötas i enlighet med landets
alla lagar och föreskrifter.
Related
Documentation
154
•
SRX110 Services Gateway Electrical Safety Guidelines and Warnings on page 155
•
SRX110 Services Gateway Laser and LED Safety Guidelines and Warnings on page 145
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 23
Electrical Safety Guidelines and Warnings
•
SRX110 Services Gateway Electrical Safety Guidelines and Warnings on page 155
SRX110 Services Gateway Electrical Safety Guidelines and Warnings
This topic includes the following sections:
•
Electrical Safety Guidelines and Warnings In Case of Electrical Accident on page 155
•
General Electrical Safety Guidelines and Warnings on page 155
Electrical Safety Guidelines and Warnings In Case of Electrical Accident
In Case of Electrical Accident
If an electrical accident results in an injury, take the following actions in this order:
Use caution. Be aware of potentially hazardous conditions that could cause further
injury.
1.
2. Disconnect power from the services gateway.
3. If possible, send another person to get medical aid. Otherwise, assess the condition
of the victim, then call for help.
General Electrical Safety Guidelines and Warnings
•
Install the services gateway in compliance with the following local, national, or
international electrical codes:
•
United States—National Fire Protection Association (NFPA 70), United States
National Electrical Code
•
Canada—Canadian Electrical Code, Part 1, CSA C22.1
•
Other countries—International Electromechanical Commission (IEC) 60364, Part 1
through Part 7
•
Evaluated to the TN power system
•
Locate the emergency power-off switch for the room in which you are working so that
if an electrical accident occurs, you can quickly turn off the power.
•
Do not work alone if potentially hazardous conditions exist anywhere in your workspace.
Copyright © 2016, Juniper Networks, Inc.
155
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
Related
Documentation
156
•
Never assume that power is disconnected from a circuit. Always check the circuit before
starting to work.
•
Carefully look for possible hazards in your work area, such as moist floors, ungrounded
power extension cords, and missing safety grounds.
•
Operate the services gateway within marked electrical ratings and product usage
instructions.
•
For the services gateway and peripheral equipment to function safely and correctly,
use the cables and connectors specified for the attached peripheral equipment, and
make certain they are in good condition.
•
SRX110 Services Gateway Power Specifications and Requirements on page 39
•
SRX110 Services Gateway Maintenance and Operational Safety Guidelines and Warnings
on page 149
•
Grounding the SRX110 Services Gateway on page 72
•
SRX110 Services Gateway Agency Approvals on page 157
Copyright © 2016, Juniper Networks, Inc.
CHAPTER 24
Agency Approvals and Regulatory
Compliance Information
•
SRX110 Services Gateway Agency Approvals on page 157
•
SRX110 Services Gateway Compliance Statements for EMC Requirements on page 158
•
SRX110 Services Gateway Compliance Statements for Environmental
Requirements on page 160
•
SRX110 Services Gateway Compliance Statements for Acoustic Noise on page 160
SRX110 Services Gateway Agency Approvals
The services gateway complies with the following standards:
•
•
Safety
•
CSA 60950-1 (2003) Safety of Information Technology Equipment
•
UL 60950-1 (2003) Safety of Information Technology Equipment
•
EN 60950-1 (2001) Safety of Information Technology Equipment
•
IEC 60950-1 (2001) Safety of Information Technology Equipment (with country
deviations)
•
EN 60825-1 +A1+A2 (1994) Safety of Laser Products - Part 1: Equipment Classification
•
EN 60825-2 (2000) Safety of Laser Products - Part 2: Safety of Optical Fiber Comm.
Systems
EMC
•
•
EN 300 386 V1.4.1 (2008) Telecom Network Equipment - EMC requirements
EMI
•
EN 55022 (CISPR 22) (2006)+A1 (2007) Class B European Radiated Emissions
•
AS/NZS CISPR 22 (2006) Class B
•
FCC Part 15 Subpart B Class B (2009) USA Radiated Emissions
•
Industry Canada ICES-003 Issue 4, February 7, 2004 Class B
•
VCCI V-3 (2009.04) and V-4 (2009.04) Class B Japanese Radiated Emissions
Copyright © 2016, Juniper Networks, Inc.
157
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
•
Related
Documentation
•
SMI CNS 13438 and NCC C6357 Taiwan Radiated Emissions
•
TEC/EMI/TEL-001/01/FEB-09 Clause 9.2, Radiated Radio Frequency,
Electromagnetic Field
•
ETSI EN 300 386 V1.4.1 (2008-04)
Immunity
•
EN 55024 (2001) +A2 (2003) +EN 55024 (2010) Information Technology Equipment
Immunity Characteristics
•
EN-61000-3-2 (2006) +A2 (2009) Power Line Harmonics
•
EN-61000-3-3 (2008) Power Line Voltage Fluctuations
•
SRX110 Services Gateway Electrical Safety Guidelines and Warnings on page 155
•
SRX110 Services Gateway Compliance Statements for EMC Requirements on page 158
•
SRX110 Services Gateway Compliance Statements for Environmental Requirements
on page 160
SRX110 Services Gateway Compliance Statements for EMC Requirements
This topic includes the following sections:
•
Canada on page 158
•
European Community on page 158
•
Japan on page 159
•
Korean on page 159
•
United States on page 159
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
European Community
This is a Class B product.
158
Copyright © 2016, Juniper Networks, Inc.
Chapter 24: Agency Approvals and Regulatory Compliance Information
Japan
The preceding translates as follows:
This is a Class B product based on the standard of the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this product is used near
a radio or television receiver in a domestic environment, it may cause radio interference.
Install and use the equipment according to the instruction manual.
Korean
Korean Class B Warning
g040914
This is a Class B product.
United States
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Copyright © 2016, Juniper Networks, Inc.
159
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
SRX110 Services Gateway Compliance Statements for Environmental Requirements
This topic includes the compliance statement for the following environmental
requirement:
Lithium Battery
Batteries in this product are not based on mercury, lead, or cadmium substances. The
batteries used in this product are in compliance with EU Directives 91/157/EEC, 93/86/EEC,
and 98/101/EEC. The product documentation includes instructional information about
the proper method of reclamation and recycling.
SRX110 Services Gateway Compliance Statements for Acoustic Noise
Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegel
beträgt 70 dB(A) oder weniger gemäss EN ISO 7779
Translation:
The maximum emitted sound pressure level is 70 dB(A) or less per EN ISO 7779.
Related
Documentation
160
•
SRX110 Services Gateway Compliance Statements for Environmental Requirements
on page 160
•
SRX110 Services Gateway Compliance Statements for EMC Requirements on page 158
•
SRX110 Services Gateway Agency Approvals on page 157
Copyright © 2016, Juniper Networks, Inc.
PART 7
Index
•
Index on page 163
Copyright © 2016, Juniper Networks, Inc.
161
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
162
Copyright © 2016, Juniper Networks, Inc.
Index
Symbols
#, comments in configuration statements..................xvii
( ), in syntax descriptions...................................................xvii
3G LED........................................................................................20
3G USB modem
configuring......................................................................102
key features.......................................................................12
protection cover..............................................................10
supported types..............................................................10
using.....................................................................................10
< >, in syntax descriptions..................................................xvii
[ ], in configuration statements........................................xvii
{ }, in configuration statements.......................................xvii
| (pipe), in syntax descriptions.........................................xvii
A
accessory list.............................................................................51
adapter, console port
chassis.........................................................................77, 88
agency approvals...................................................................157
agency labels..........................................................................123
Alarm LED..................................................................................20
monitoring........................................................................110
alarms
relay contacts...................................................................41
wire specifications..........................................................41
altitude, acceptable range..................................................30
approvals, agency..................................................................157
AT modem command.....................................................76, 77
ATDT modem command......................................................77
autoinstallation
overview............................................................................49
B
basic CLI command
3G USB modem............................................................102
basic connectivity
secure Web access........................................................87
boot devices
types....................................................................................22
Copyright © 2016, Juniper Networks, Inc.
boot media
monitoring........................................................................112
braces, in configuration statements...............................xvii
brackets
angle, in syntax descriptions....................................xvii
square, in configuration statements......................xvii
branch SRX
factory default
configuration..........................................................90
C
cables
console port cable (chassis),
connecting.............................................................77, 88
Ethernet cable, connecting.................................77, 88
CAT-5e.........................................................................................41
chassis alarms
sample...............................................................................112
clearance requirements................................................34, 35
CLI show commands..........................................................109
comments, in configuration statements......................xvii
compliance
acoustic noise...............................................................160
EMC requirements.......................................................158
general standards.........................................................157
component
return procedure ...........................................................122
configuration
using the setup wizard.................................................99
configuration, services gateway........................................83
configure
3G USB modem............................................................102
VDSL2...............................................................................103
connectivity
LAN.........................................................................................3
modem (remote) connection..................................88
through J-Web................................................................86
through the CLI locally.................................................88
through the CLI remotely............................................88
WAN.......................................................................................3
console port
adapter (chassis)....................................................77, 88
cable specifications.......................................................41
connecting through the CLI locally.........................88
connecting through the CLI remotely....................88
settings for local CLI connection.............................88
163
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
settings for modem connection at device for
remote CLI access.....................................................76
settings for modem connection for remote CLI
access.............................................................................77
console port, RJ-45................................................................43
conventions
text and syntax...............................................................xvi
curly braces, in configuration statements....................xvii
customer support.................................................................xviii
contacting JTAC............................................................xviii
font conventions.....................................................................xvi
G
ge-0/0
connecting through J-Web.........................................86
guidelines
electrical..........................................................................155
electrical wiring...............................................................37
installing............................................................................30
H
D
DB-9 to DB-25 serial port adapter....................................77
DDR memory...............................................................................4
desk
installing............................................................................63
desk installation
preparing...........................................................................56
desk mount
preparing...........................................................................56
device grounding.....................................................................72
dial-up modem connection See modem connection
to console port
documentation
comments on.................................................................xvii
hardware components
maintenance..................................................................107
monitoring........................................................................112
hardware features.....................................................................4
Hayes-compatible modem See modem connection
to console port
HTTP (Hypertext Transfer Protocol)
on built-in management interfaces........................87
HTTPS (Hypertext Transfer Protocol over SSL)
recommended for secure access.............................87
HyperTerminal, for terminal emulation
local CLI connection.....................................................88
modem connection at device for remote CLI
access.............................................................................76
modem connection for remote CLI access...........77
E
electricity
safety warnings.............................................................155
electromagnetic compatibility...........................................37
EMC (EMI)
compliance with requirements...............................158
standards.........................................................................157
encrypted access
through HTTPS...............................................................87
through SSL......................................................................87
environmental specifications............................................30
Ethernet cable
connecting the services gateway to a
management device................................................88
connecting the services gateway to a
modem...........................................................................77
Ethernet port
cable specifications.......................................................41
RJ-45...................................................................................42
F
I
immunity standards.............................................................157
installation
guidelines..........................................................................30
safety guidelines...........................................................135
safety requirements.....................................................135
safety warnings.............................................................135
installation parts.....................................................................48
installation site
electrical wiring guidelines..........................................37
installation tools.....................................................................48
interface alarms......................................................................112
interface cable
connecting........................................................................75
organizing..........................................................................75
specifications...................................................................41
interfaces
built-in..................................................................................17
hardware.............................................................................17
Internet..........................................................................................3
factory-default configuration............................................115
fire safety specifications.....................................................137
164
Copyright © 2016, Juniper Networks, Inc.
Index
J
J-Web interface.......................................................................86
connecting........................................................................86
JTAC......................................................................................117, 121
information required....................................................124
requesting support.......................................................124
Juniper Networks Technical Assistance
Center..........................................................117, 121 See JTAC
Junos OS
establishing secure Web access..............................87
Junos OS CLI
connecting locally.........................................................88
connecting remotely....................................................88
L
laptop See management device
laser safety guidelines.........................................................145
LED
front panel.........................................................................19
port.......................................................................................19
SYNC...................................................................................22
TX/RX.................................................................................22
LEDs
safety warnings.............................................................145
LINK/ACTIVE LED....................................................................21
local connection to the console port..............................88
M
maintenance guidelines
warnings..........................................................................149
management device
connecting to J-Web....................................................86
manuals
comments on.................................................................xvii
modem commands
at device end....................................................................76
at remote end...................................................................77
modem connection to console port
configuring modem at services gateway
end...................................................................................76
configuring modem at user end................................77
connecting modem to device....................................77
overview............................................................................88
N
network..........................................................................................3
P
parentheses, in syntax descriptions...............................xvii
Copyright © 2016, Juniper Networks, Inc.
parts list.......................................................................................51
PC See management device
pinouts........................................................................................44
RJ-45............................................................................42, 43
port settings..............................................................................76
power
shutdown...........................................................................81
Power LED.................................................................................20
monitoring........................................................................110
status.................................................................................114
power supply
connecting........................................................................79
maintenance..................................................................107
power system
monitoring........................................................................114
requirements...................................................................39
specifications .................................................................39
protection cover.......................................................................10
R
rack
installing............................................................................59
rack installation
preparing...........................................................................55
rack mount
preparing...........................................................................55
radio frequency interference...............................................37
remote connection to console port
configuring modem at services gateway
end...................................................................................76
configuring modem at user end................................77
connecting modem to device....................................77
overview............................................................................88
requirements
airflow clearance............................................................34
cabinet airflow.................................................................32
cabinet size.......................................................................32
electrical............................................................................38
geographical area..........................................................33
hardware maintenance...............................................34
power..................................................................................38
rack size..............................................................................33
rack strength....................................................................33
spacing mounting brackets........................................33
rescue configuration..............................................................115
Reset Config button
CLI commands...............................................................116
set chassis commands...............................................116
using...................................................................................115
165
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
return
component......................................................................122
services gateway...........................................................122
RJ-11 connector pinouts........................................................44
RJ-45 pinouts
console port.....................................................................43
Ethernet port....................................................................42
RJ-45 to DB-9 serial port adapter
chassis console port......................................................77
root password
at initial local connection (none)............................88
RS-232 (EIA-232) ...................................................................41
S
safety guidelines
general...............................................................................131
installation......................................................................139
LED.....................................................................................145
safety standards....................................................................157
safety warning levels
definition..........................................................................129
safety warnings
general...............................................................................131
installation......................................................................139
laser...................................................................................145
maintenance and operational.................................149
secure access
HTTPS recommended.................................................87
overview.............................................................................87
requirements....................................................................87
Secure Sockets Layer See SSL
serial number..........................................................................123
services gateway........................................................................3
3G..........................................................................................10
autoinstallation..............................................................49
back panel.........................................................................15
chassis alarms................................................................112
components......................................................................15
desk installation.............................................................63
establishing secure Web access..............................87
front panel.........................................................................15
grounding...........................................................................72
hardware interfaces........................................................17
HTTPS Web access.......................................................87
installation overview.....................................................47
installation process.......................................................47
LEDs.....................................................................................19
monitoring component LEDs...................................110
parts....................................................................................48
166
power supply..............................................................9, 80
powering off......................................................................81
powering on.....................................................................80
rack installation..............................................................59
resetting............................................................................114
return procedure ...........................................................122
SSL access........................................................................87
tools....................................................................................48
unpacking...........................................................................51
VDSL2...................................................................................6
verifying parts...................................................................51
wall installation..............................................................65
services gateway, configuration........................................83
setup wizard
default setup mode....................................................100
description.......................................................................99
guided setup mode......................................................101
running..............................................................................101
show chassis commands
show chassis alarms..................................................109
show chassis environment.......................................109
show chassis fpc..........................................................109
show chassis hardware.............................................109
shutdown
graceful...............................................................................81
immediate.........................................................................81
signaling limitations...............................................................37
site, environmental specifications...................................30
specifications
cable....................................................................................41
environmental.................................................................30
fire safety..........................................................................137
wires to external alarm-reporting devices............41
SRX110 Services Gateway .....................................................3
SSL (Secure Sockets Layer)
management access....................................................87
standards compliance.........................................................157
Status LED.................................................................................20
monitoring........................................................................110
support, requesting from JTAC..........................................121
support, technical See technical support
supported profile
VDSL2....................................................................................7
SYNC LED...........................................................................20, 22
syntax conventions................................................................xvi
T
technical support
contacting JTAC............................................................xviii
Copyright © 2016, Juniper Networks, Inc.
Index
temperature, acceptable range........................................30
thermal output........................................................................30
TX/RX LED.........................................................................20, 22
U
USB modem..............................................................................10
V
VDSL/ADSL-ISDN port...........................................................6
VDSL/ADSL-POTS port..........................................................6
VDSL2
configuring......................................................................103
key features.........................................................................6
LEDs.....................................................................................22
supported profiles.............................................................7
VDSL2 port..................................................................................6
W
wall
installing............................................................................65
wall installation
preparing............................................................................57
wall mount
preparing............................................................................57
warnings
electrical..........................................................................155
wire specifications...................................................................41
wireless........................................................................................10
Copyright © 2016, Juniper Networks, Inc.
167
SRX110 Services Gateway Hardware Guide for H2 Model Numbers
168
Copyright © 2016, Juniper Networks, Inc.