Spectra® IV SE Horizon Series Dome Systems

PRODUCT SPECIFICATION
camera solutions
Spectra® IV SE Horizon Series Dome Systems
CRYSTAL CLEAR, INTEGRATED LOOK-UP DOME SYSTEM
Product Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Unparalleled Crystal Clear Video at Any Angle
Vertical Tilt of up to 18° Above Horizontal
Autofocus, High Resolution Integrated Camera/Optics Package
Day/Night, 540 TVL, 128X Wide Dynamic Range (WDR), Motion
Detection, and Electronic Image Stabilization
Window Blanking
Camera Title Overlay, 20 User-Definable Characters
Horizontal and Zone Blanking
On-Screen Compass and Tilt Display
Password Protection
Freeze Frame During Presets
Built-in Surge and Limited Lightning Protection
Integrated Passive Unshielded Twisted Pair (UTP) Circuit
Low Lux Noise Reduction
An important, but often overlooked, component of a high-speed
dome system is the relationship between the dome bubble and the
camera lens. Special consideration was taken when designing the
Spectra® IV SE Horizon lower dome bubble to ensure that an optimal
optical relationship between the lens and bubble was achieved,
providing crystal clear video at long focal lengths and extended
vertical angles.
The Spectra IV SE Horizon dome drive’s unique integrated optics
package incorporates many advanced features that allow the
system to produce high quality video in the most difficult
environments. The camera in the Spectra IV SE Horizon dome drive
features vertical tilt of 18° above the horizon, providing optical clarity
and the ability to look up. LowLight™ technology allows the camera
to compensate for scenes where minimal light is present. The
camera features advanced 128X wide dynamic range that enables
the system to compensate for scenes where dramatic contrasts in
lighting are present. Electronic image stabilization digitally
reduces blurring of the camera image due to vibration caused by
external sources such as wind and traffic.
Spectra IV SE Horizon back box options include environmental
in-ceiling, standard pendant, and environmental pendant models.
Each back box model features built-in back box memory to store
camera and location-specific dome settings, including labels,
presets, patterns, and zones. A passive UTP circuit is located on
the door assembly for convenient video transmission through twisted
pair wire. For added flexibility, Pelco fiber modules can also be
attached to the door assembly for transmission over single-mode or
multimode fiber.
ENVIRONMENTAL
IN-CEILING MODEL
SD4H35-F-E0
PENDANT MODEL
SD4H35-PG-0
• Ability to Add IP Network Capability by Purchasing Optional TXB-IP
Module
Spectra IV SE Horizon dome systems feature many software
enhancements that increase performance and make configuration
and operation easy. An internal scheduling clock allows for the
scheduling of presets and patterns. Window blanking enables a
user to configure up to eight, four-sided, user-defined privacy areas.
Password protection prevents unauthorized users from changing
the system settings. Configurable on-screen compass and tilt
display provides positioning information when needed. Intuitive
multilingual on-screen menus can be displayed in English, Spanish,
Portuguese, Italian, French, German, Russian, Polish, Turkish, and
Czech.
Spectra IV SE Horizon’s variable speed capabilities range from a
smooth, fast pan motion of 400 degrees per second to a smooth
“creep” speed of 0.1 degree per second. The system is capable of
continuous 360 degrees rotation and has an “auto flip” feature that
allows the dome to rotate 180 degrees and reposition itself for
uninterrupted viewing of any subject that passes directly beneath
the dome.
In addition, with the optional Pelco TXB-IP module, you can add IP
network capability at any time to a Spectra IV dome system without
losing analog viewing and control. By snapping the TXP-IP module
into the back box, you can stream network video to a Web browser,
Endura®, Digital Sentry®, or third-party software recording solution
allowing integration into virtually any IP-based system.
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C3434 / REVISED 10-31-10
TECHNICAL SPECIFICATIONS
DOME DRIVE FEATURES
• Vertical Tilt of 18° Above Horizontal
• Action on Alarm: Alarms Can Be Individually Configured for 3 Priority
Levels, to Initiate a Stored Pattern, or to Go to an Associated Preset When
Received
• 256 Presets
• ±0.1° Preset Accuracy
• Resume After Alarm: Allows the Dome to Return to a Previously
Configured State After Alarm Acknowledgement or to its Previous
Position Before Alarm
• Electronic Image Stabilization
• Extended Vertical Angles
• Multilanguage Menus (English, Spanish, Portuguese, Italian, French,
German, Russian, Polish, Turkish, and Czech)
• RJ-45 Data Port for Software Update and Setup
• On-Screen Compass, Tilt, and Zoom Display
• 400°/sec Pan Preset Speed and 200°/sec Tilt Preset Speed
• Rotating Discreet Liner with Sealed Fixed Bubble
• Window Blanking: Up to 8, Four-Sided, User-Defined Shapes
• 8 Zones (configurable in size) Can Be Labeled with up to 20 Characters
Each or Set to Output Blank Video
• 7 Alarm Inputs
• Multiple Park and Power-Up Action
• Patterns: Up to 8, On-Screen, User-Defined Configurable Patterns;
Includes Pan, Tilt, Zoom, and Preset Functions
• Proportional Pan/Tilt: Continually Decreases Pan/Tilt Speeds in Proportion
to Depth of Zoom
• Variable Scan Speed: Scan Speed Can Be Configurable Between
1–40°/sec
• Pan Motion Allows 0.1–150°/sec Pan Speed
• Configurable Limit Stops for Auto/Random/Frame Scan Modes
• Auto-sensing Protocol (Coaxitron®, RS-422 Pelco P and Pelco D); Accepts
Competitive Control Protocol with Optional Translator Card
• 1 Auxiliary (Form C) Relay Output and 1 Open Collector Auxiliary Output
(can be alternately configured to operate upon alarm)
• Digital Position, Zoom Control, and Feedback Through Pelco D Protocol
• Configurable Locations of Labels and On-Screen Displays
• Built-in Menu System for Setup of Configurable Functions
• “Auto Flip” Rotates Dome 180° at Bottom of Tilt Travel
• Configurable Zoom Speeds
BACK BOX FEATURES
9.9 (25.2)
Environmental In-Ceiling
• Built-in Memory Stores Camera/Dome Settings
4.4
(11.0)
• Single Back Box for Hard Ceiling Applications
• Requires 4.4-Inch Space Above Ceiling and 6.4 Inches Below
• Includes Heater and Fan
• Minimum Ceiling Thickness 0.5-Inch; Maximum 1.75 Inches
6.4
(16.2)
• Quick Disconnect to Dome Drive
• Aluminum Construction
• Integrated Passive UTP
6.0 (15.24)
8.6 (21.8)
Standard and Environmental Pendant
• Standard and Environmental Models
13.0
(33.1)
• Built-in Memory Stores Camera/Dome Settings
• Quick Disconnect to Dome Drive
• Aluminum Construction
• Environmental Model Includes Sun Shield, Fan, and Heater
• Integrated Passive UTP
(STANDARD PENDANT MODEL)
6.0 (15.24)
8.6 (21.8)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;
ALL OTHERS ARE INCHES.
TECHNICAL SPECIFICATIONS
CAMERA/OPTICS
Signal Format
Scanning System
Image Sensor
Effective Pixels
NTSC
PAL
Horizontal Resolution
NTSC
PAL
Lens
Zoom
Zoom Speed (optical range)
Horizontal
Angle of View
Focus
Maximum Sensitivity
at 35 IRE
NTSC/EIA
CERTIFICATIONS/RATINGS/PATENTS
NTSC (DD4H35)
PAL (DD4H35-X)
2:1 Interlace/1:1 progressive scan (user
selectable)
1/4-inch EXview HAD™
•
•
•
•
•
768 (H) X 494 (V)
752 (H) X 582 (V)
Meets the following standards:
• NEMA Type 4X, IP66 when installed properly
>540 TV Lines
>540 TV Lines
f/1.4 (focal length, 3.4 ~ 119 mm)
35X optical, 12X digital
3.2/4.6/6.6 seconds
55.8° at 3.4 mm wide zoom; 1.7° at 119 mm
telephoto zoom
Automatic with manual override
0.55 lux at 1/60 sec (color)
0.018 lux at 1/2 sec (color)
0.00018 lux at 1/2 sec (B-W)
PAL/CCIR
0.45 lux at 1/50 sec (color)
0.015 lux at 1/1.5 sec (color)
0.00015 lux at 1/1.5 sec (B-W)
Sync System
Internal/AC line lock, phase adjustable using
remote control, V-Sync
White Balance
Automatic with manual override
Shutter Speed
Automatic (electronic iris)/Manual
NTSC
1/2 ~ 1/30,000
PAL
1/1.5 ~ 1/30,000
Iris Control
Automatic Iris Control with manual override
Gain Control
Automatic/OFF
Video Output
1 Vp-p, 75 ohms
Video Signal to Noise
>50 dB
Wide Dynamic Range
128X
Electronic Image Stabilization Integrated
Image Enhancement
Integrated
MECHANICAL (Dome Drive Only)
Pan Movement
Vertical Tilt
Manual Pan/Tilt Speeds
Pan
Tilt
Preset Speeds
Pan
Tilt
360° continuous pan rotation
Unobstructed +18° to –92°
0.1° to 80°/sec manual operation,
150°/sec Turbo
0.1° to 40°/sec manual operation
400°/sec
200°/sec
For variable-speed operation an appropriate
controller is required. (With nonvariable
speed control, Spectra IV SE Horizon pan/tilt
speed is 20°/sec)
ELECTRICAL
Input Voltage
Input Power
24 VAC
24 VDC
Fuse
Auxiliary Outputs
Alarm Inputs
18 to 32 VAC; 24 VAC nominal
22 to 27 VDC; 24 VDC nominal
23 VA nominal (without heater);
73 VA nominal (with heater)
0.7 A nominal (without heater);
3 A nominal (with heater)
1.25 A
2
7
CE, Class B
FCC, Class B
UL/cUL Listed
C-Tick
U.S. Patents 5,931,432; 6,793,415 B2; 6,802,656 B2; 6,821,222 B2
GENERAL
Construction
Back Box
In-Ceiling
Pendant
Dome Drive
Bubble
Light Attenuation
Smoked
Clear
Cable Entry (back box)
In-Ceiling
Pendant
Weight (approximate)
Back Box
Environmental
In-Ceiling
Standard Pendant
Environmental Pendant
Dome Drive
Lower Dome
Environment
Environmental In-Ceiling
Pendant, Standard
and Environmental
Operating Temperature
Standard Pendant
Maximum
Minimum
Environmental
In-Ceiling and
Environmental Pendant
Maximum
Minimum
Effective Projected
Area (EPA)
Aluminum
Aluminum
Aluminum, thermo plastic
Acrylic
f/0.5 light loss
Zero light loss
0.75-inch conduit fitting
Through 1.5-inch NPT pendant mount
Unit
Shipping
2.1 lb
2.4 lb
3.5 lb
3.0 lb
0.8 lb
(0.95 kg)
(1.09 kg)
(1.59 kg)
(1.36 kg)
(0.40 kg)
3 lb
4 lb
5 lb
4 lb
2 lb
(1.36 kg)
(1.81 kg)
(2.27 kg)
(1.81 kg)
(0.90 kg)
Outdoor
Indoor/outdoor
(Assumes no wind chill factor)
113°F (45°C) absolute maximum;
95°F (35°C) sustained maximum
25°F (–4°C) sustained minimum
(Assumes no wind chill factor)
140°F (60°C) absolute maximum;
122°F (50°C) sustained maximum
–60°F (–51°C) absolute minimum; prevents
icing at sustained minimum of –50°F (–45°C);
de-ices 0.1 inch (2.5 mm) within 3 hours after
power-up
24 square inches (without mount)
50.6 square inches (with IWM Series mount)
RELATED PRODUCTS
SYSTEM MODEL NUMBERS
Type
Back Box Color
In-Ceiling, Environmental*
Black
Pendant, Standard
Lt. Gray
Pendant, Environmental*
Lt. Gray
Lower Dome
NTSC
PAL
Smoked
SD4H35-F-E0
SD4H35-F-E0-X
Clear
SD4H35-F-E1
SD4H35-F-E1-X
Smoked
SD4H35-PG-0
SD4H35-PG-0-X
Clear
SD4H35-PG-1
SD4H35-PG-1-X
Smoked
SD4H35-PG-E0
SD4H35-PG-E0-X
Clear
SD4H35-PG-E1
SD4H35-PG-E1-X
*Environmental dome systems include a heater, fan, and the environmental pendant also includes a sun shield.
COMPONENT MODEL NUMBERS
Back Box
Dome Drive
BB4-F-E In-ceiling, black, environmental
DD4H35
BB4-PG Pendant mount, gray, standard
BB4-PG-E Pendant mount, gray, environmental
Lower Dome
Day/Night (NTSC) camera (35X) LD4H-0 Smoked
LD4H-1 Clear
OPTIONAL ACCESSORIES
RECOMMENDED MOUNTS
IPS-CABLE
In-Ceiling Domes
SD5-P
Remote monitor cable and software kit
consisting of the Spectra IV remote monitor
interface cable and necessary software for
use with a PC. Refer to www.pelco.com for a
list of compatible devices.
IPS-RDPE-2†
Remote data port. 24 VAC, wall/pole mount
video/data breakout box. Allows ground-level
control/configuration and software upgrades
when used with the IPS-CABLE.
TXB Series†
Translator boards for AD™ Manchester,
Hernis, Bosch® (Philips, Burle), Sensormatic®,
Vicon™, TASS, and NTCIP protocols.
TXB-IP Series
Communication module that allows you to
control and monitor Spectra IV dome systems
over an IP network (in-ceiling and pendant
models only).
FS85011A†
Fiber transmitter sends one unidirectional
composite video channel and 1 bidirectional
data channel over 1 multimode or singlemode fiber optical cable.
†
If TXB or FS85011A boards are installed, remote upload of system software
will not be possible.
Pelco, Inc. Worldwide Headquarters:
3500 Pelco Way, Clovis, California 93612-5699 USA
USA & Canada Tel: (800) 289-9100 • FAX: (800) 289-9150
International Tel: +1 (559) 292-1981 • FAX: +1 (559) 348-1120
www.pelco.com
SCA1
Pendant Domes
BB5-PCA-BK
IWM Series
MRCA
PP4348
PP350/PP351
SWM Series
2' x 2' drop ceiling panel, aluminum
construction. Replaces 2' x 2' ceiling tile.
Support rails for BB4-F; for use in ceiling tile
applications.
Pendant conduit adapter, black
Wall mount, with or without integral 24 VAC,
100 VA transformer. Can be adapted for
corner, parapet, or pole applications.
Ceiling mount, black
Parapet roof mount
Parapet wall/roof mount
Compact wall mount. Can be adapted for
corner or pole applications.
RECOMMENDED POWER SUPPLIES
MCS Series
WCS Series
Indoor, 24 VAC power supply
Outdoor, 24 VAC power supply
Refer to individual power supply specifications for more information.
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred
to in this publication are trademarks of Pelco, Inc. or its affiliates. All other
product names and services are the property of their respective companies.
Product specifications and availability are subject to change without notice.
©Copyright 2010, Pelco, Inc. All rights reserved.