SUPER
®
SUPERWORKSTATION 5033C-T
USER’S MANUAL
Revision 1.0
The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates. Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.
SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM
THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING,
INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR
DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.
Unless you request and receive written permission from SUPER MICRO COMPUTER,
you may not copy any part of this document.
Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.
Copyright © 2004 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperWorkstation 5033CT. Installation and maintainance should be performed by experienced technicians only.
The 5033C-T is a high-end, single processor mid-tower workstation based on the
SC733T-350 mid-tower workstation chassis and the Super P4SCT+II
motherboard. The P4SCT+II supports a single Intel ® Pentium ® 4 HT (hyperthreading) processor of up to 3.40 GHz with an integrated 512KB advanced
transfer cache or Intel® Celeron ® processors of up to 2.80 GHz with an integrated 128KB advanced transfer cache.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
system and describes the main features of the Super P4SCT+II motherboard and
the SC733T-350 chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperWorkstation
5033C-T into a rack and check out the server configuration prior to powering up
the system. If your server was ordered without the processor and memory
components, this chapter will refer you to the appropriate sections of the manual
for their installation.
Chapter 3: System Interface
Refer to this chapter for details on the system interface, which includes the
functions and information provided by the control panel on the chassis as
well as other LEDs located throughout the system.
iii
SUPERWORKSTATION 5033C-T User's Manual
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperWorkstation 5033C-T.
Chapter 5: Advanced Motherboard Setup
Chapter 5 provides detailed information on the P4SCT+II motherboard, including
the locations and functions of connectors, headers and jumpers. Refer to this
chapter when adding or removing processors or main memory and when
reconfiguring the motherboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC733T-350 workstation chassis. You should follow the procedures given in this chapter when installing,
removing or reconfiguring Serial ATA or peripheral drives and when replacing
system power supply units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed
information on running the CMOS Setup Utility.
Appendix A: BIOS POST Messages
Appendix B: BIOS POST Codes
Appendix C: Software Installation
Appendix D: System Specifications
iv
Preface
Notes
v
SUPERWORKSTATION 5033C-T User's Manual
Table of Contents
Preface
About This Manual ....................................................................................................... iii
Manual Organization .................................................................................................... iii
Chapter 1: Introduction
1-1
Overview ............................................................................................................ 1-1
1-2
Motherboard Features ..................................................................................... 1-2
1-3
Chassis Features ............................................................................................ 1-5
1-4
Contacting Supermicro ................................................................................... 1-7
Chapter 2: System Installation
2-1
Overview ............................................................................................................ 2-1
2-2
Unpacking the SuperWorkstation 5033C-T ................................................... 2-1
2-3
Setting up the System ................................................................................... 2-2
Checking the Motherboard Setup ............................................................ 2-2
Checking the Drive Bay Setup ................................................................ 2-4
Chapter 3: System Interface
3-1
Overview ............................................................................................................ 3-1
3-2
Control Panel Buttons ..................................................................................... 3-1
Reset .......................................................................................................... 3-1
Power ......................................................................................................... 3-1
3-3
Control Panel LEDs ......................................................................................... 3-2
Power ......................................................................................................... 3-2
HDD ............................................................................................................ 3-2
NIC .............................................................................................................. 3-2
Overheat ..................................................................................................... 3-2
3-4
Serial ATA Drive Carrier LEDs ....................................................................... 3-3
Chapter 4: System Safety
4-1
Electrical Safety Precautions ......................................................................... 4-1
4-2
General Safety Precautions ........................................................................... 4-2
4-3
ESD Precautions ............................................................................................. 4-3
4-4
Operating Precautions .................................................................................... 4-4
vi
Table of Contents
Chapter 5: Advanced Motherboard Setup
5-1
Handling the P4SCT+II Motherboard ............................................................. 5-1
5-2
Motherboard Installation .................................................................................. 5-2
5-3
Connecting Cables .......................................................................................... 5-3
Connecting Data Cables .......................................................................... 5-3
Connecting Power Cables ........................................................................ 5-3
Connecting the Control Panel ................................................................. 5-3
5-4
I/O Ports ........................................................................................................... 5-4
5-5
Installing Processors ...................................................................................... 5-5
5-6
Installing Memory ............................................................................................ 5-6
5-7
Adding PCI Cards ............................................................................................ 5-7
5-8
Motherboard Details ........................................................................................ 5-8
P4SCT+II Layout ....................................................................................... 5-8
P4SCT+II Quick Reference ...................................................................... 5-9
5-9
Connector Definitions .................................................................................... 5-10
Power Supply Connectors ...................................................................... 5-10
PW_ON Connector ................................................................................. 5-10
Reset Connector ..................................................................................... 5-11
Overheat LED (OH) ................................................................................. 5-11
GLAN2 LED ............................................................................................. 5-11
GLAN1 LED ............................................................................................. 5-11
IDE LED ................................................................................................... 5-12
Power_LED Connector ........................................................................... 5-12
NMI Button ............................................................................................... 5-12
SMB Header ............................................................................................ 5-12
IR Connector ............................................................................................ 5-13
Serial Ports ............................................................................................. 5-13
Fan Headers ............................................................................................ 5-13
Chassis Intrusion .................................................................................... 5-14
Wake-On-LAN .......................................................................................... 5-14
Wake-On-Ring ......................................................................................... 5-14
ATX PS/2 Keyboard and PS/2 Mouse Ports ....................................... 5-14
Universal Serial Bus ............................................................................... 5-15
GLAN1/2 (Ethernet) Ports ...................................................................... 5-15
SATA LED (Marvell) ................................................................................ 5-15
SATA LED (Intel) .................................................................................... 5-15
5-10 Jumper Settings ............................................................................................. 5-16
Explanation of Jumpers .......................................................................... 5-16
CMOS Clear ............................................................................................ 5-16
vii
SUPERWORKSTATION 5033C-T User's Manual
Front Side Bus Speed ............................................................................ 5-16
USB Wake-Up ......................................................................................... 5-17
Watch Dog Enable/Disable .................................................................... 5-17
Speaker Jumper ...................................................................................... 5-17
Keyboard Wake-Up ................................................................................. 5-18
GLAN2 Enable/Disable ........................................................................... 5-18
VGA Enable/Disable ............................................................................... 5-18
Keylock Enable/Disable ......................................................................... 5-18
SATA Enable/Disable ............................................................................. 5-19
5-11 Onboard Indicators ........................................................................................ 5-19
Standby Power LED ............................................................................... 5-19
5-12 Parallel Port, Floppy/IDE Hard Drive and AGP Connections ................... 5-20
Parallel Port Connector .......................................................................... 5-20
Floppy Connector .................................................................................... 5-21
IDE Connectors ....................................................................................... 5-21
8xAGP Slot ............................................................................................. 5-22
Chapter 6: Advanced Chassis Setup
6-1
Static-Sensitive Devices ................................................................................. 6-1
6-2
Front Control Panel ......................................................................................... 6-2
6-3
System Fans .................................................................................................... 6-5
Fan Failure ................................................................................................. 6-5
Replacing System Fans ........................................................................... 6-5
6-4
Drive Bay Installation ...................................................................................... 6-7
Serial ATA Drives ...................................................................................... 6-7
Installing Components in the 5.25" Drive Bays ................................... 6-10
6-5
Power Supply ................................................................................................. 6-11
Replacing the Power Supply ................................................................. 6-11
Chapter 7: BIOS
7-1
Introduction ....................................................................................................... 7-1
7-2
Running Setup ................................................................................................. 7-2
7-3
Main BIOS Setup ............................................................................................ 7-2
7-4
Advanced BIOS Setup .................................................................................... 7-4
7-4.1 Advanced BIOS Features ............................................................. 7-4
7-4.2 Advanced Chipset Control ............................................................ 7-5
7-4.3 I/O Device Configuration ............................................................... 7-7
7-4.4 PnP Configuration .......................................................................... 7-9
7-4.5 Console Redirection .................................................................... 7-10
7-4.6 Hardware Monitor ......................................................................... 7-11
viii
Table of Contents
7-4.7 Processor & Clock Options ........................................................ 7-12
7-5
Security .......................................................................................................... 7-13
7-6
Boot ................................................................................................................. 7-14
7-7
Exit .................................................................................................................. 7-15
Appendices:
Appendix A: BIOS POST Messages ....................................................................... A-1
Appendix B: BIOS POST Codes ............................................................................. B-1
Appendix C: Software Installation ........................................................................... C-1
Appendix D: System Specifications ....................................................................... D-1
ix
SUPERWORKSTATION 5033C-T User's Manual
Notes
x
Chapter 1: Introduction
Chapter 1
Introduction
1-1
Overview
Supermicro's 5033C-T is a high-end single processor workstation. The 5033CT is comprised of two main subsystems: the SC733T-350 chassis and the
P4SCT+II motherboard. The P4SCT+II supports a single 478-pin Intel Pentium
4 microPGA processor at up to 3.40 GHz with HT (hyper-threading) technology
(or single a Intel Celeron processor of up to 2.80 GHz) and up to 4 GB of ECC
or non-ECC unbuffered DDR400/333/266 SDRAM memory. Please refer to our
web site for information on operating systems that have been certified for use with
the 5033C-T (www.supermicro.com) and for regular updates on supported processor speeds.
In addition to the motherboard and chassis, various hardware components may
have been included with the 5033C-T, as listed below.
!
One CPU retention mechanism (SKT-0109)
!
Serial ATA (SATA) Accessories:
One (1) internal SATA backplane (CSE-SATA-733)
Four (4) SATA cables (CBL-0044)
One (1) SATA LED cable (CBL-0056)
Four (4) SATA drive carriers (CSE-PT39)
!
One (1) 12-cm exhaust fan (FAN-0055)
!
One (1) 9-cm cooling fan with air shroud (FAN-0060)
!
One (1) CD containing drivers and utilities
!
SuperWorkstation 5033C-T User's Manual
1-1
SUPERWORKSTATION 5033C-T User's Manual
1-2
Motherboard Features
At the heart of the SuperWorkstation 5033C-T lies the P4SCT+II, a single processor motherboard designed to provide maximum performance. Below are the
main features of the P4SCT+II.
Chipset Overview
The P4SCT+II is based on Intel’s 875P chipset. See Figure 1-1 for a block
diagram of the chipset. The 875P chipset is made up of two main components:
The Memory Controller Hub (MCH)
The I/O Controller Hub (6300ESB)
Memory Controller Hub (MCH)
The MCH includes the host (CPU) interface, memory interface, I/O controller hub
interface, CSA interface and AGP interface. It contains advanced power management logic and supports dual-channel (interleaved) DDR memory, providing bandwidth of up to 6.4 GB/s using DDR-400 SDRAM. The MCH supports the following
front side bus/memory bus configurations: 800 MHz FSB with a 400/333 memory
interface, a 533 MHz FSB with a 333/266 memory interface and a 400 MHz FSB
with a 266 MHz memory interface. The AGP interface supports 8x data transfers
and operates at a peak bandwidth of 2.1 GB/s. The CSA (Communications
Streaming Architecture) interface connects the MCH to a Gigabit Ethernet controller.
I/O Controller Hub (6300ESB)
The 6300ESB ICH controller hub provides the I/O subsystem with access to the rest
of the system. It integrates two Serial ATA (SATA) host controllers, a dual-channel
Ultra ATA/100 bus master IDE controller, an SMBus 2.0 controller, the LPC/Flash
BIOS interface, the PCI-X (66MHz) 1.0 interface, the PCI 2.2 interface and the
System Management Controller.
1-2
Chapter 1: Introduction
Processors
The P4SCT+II supports a single Intel® Pentium® 4 HT (hyper-threading) processor of up to 3.40 GHz with an integrated 512KB advanced transfer cache or Intel®
Celeron ® processors of up to 2.80 GHz with an integrated 128KB advanced
transfer cache. Please refer to the support section of our web site for a complete
listing of supported processors (http://www.supermicro.com/support/).
Memory
The P4SCT+II has four (4) 184-pin DIMM sockets that can support up to 4 GB
of ECC or non-ECC unbuffered DDR400/333/266 SDRAM modules. (Memory
operates in a dual-channel, or interleaved configuration for increased performance.) Module sizes of 128 MB, 256 MB, 512 MB and 1 GB may be used to
populate the DIMM slots.
Serial ATA
A Serial ATA controller is incorporated into the 875P chipset to provide a twoport Serial ATA subsystem. A Marvell 88SX5080 controller is also included
onboard the P4SCT+II, which provides support for four additional SATA ports.
The SATA drives are hot-swappable units and RAID 0 and RAID 1 supported.
Note: The operating system you use must have RAID support to enable the hotswap capability and RAID function of the Serial ATA drives.
PCI Expansion Slots
The P4SCT+II has two 32-bit, 33 MHz (5V) PCI slots and three 64-bit, 66 MHz
(3.3V) PCI-X slots. The SC733T-350 chassis can accommodate cards being
installed in all five slots.
Ethernet Ports
The P4SCT+II has an Intel ® 82547GI CSA Gigabit Ethernet controller and an
Intel® 82541 Gigabit Ethernet controller onboard. Together these controllers can
support a total of two Gigabit LAN ports.
AGP Slot
A 15.V 8xAGP slot for use with high-performance video cards is included on the
motherboard. The AGP slot is backward compatible with 4xAGP and 2xAGP.
1-3
SUPERWORKSTATION 5033C-T User's Manual
Onboard Controllers/Ports
An onboard IDE controller supports one floppy drive and up to four Ultra ATA 100
hard drives or ATAPI devices. Onboard I/O backpanel ports include one serial
COM port, one parallel port, four USB ports, PS/2 mouse and keyboard ports and
two GLAN (RJ45) ports.
Other Features
Other onboard features that promote system health include eight voltage monitors, a chassis intrusion header, auto-switching voltage regulators, chassis and
CPU overheat sensors, virus protection and BIOS rescue.
Pentium 4
Processor
DDR-400/333/266
SDRAM
800/533/400 MHz System Bus
1.5V 8xAGP
GLAN (Intel)
Keyboard/Mouse
MCH
FWH
Floppy Drive
Serial Ports
LPC I/O
UDMA/100
IDE Primary/
Secondary
SATA
SATA Primary/
Secondary
6300ESB
Parallel Port
Monitor
USB
Ports (4)
USB 2.0
PCI-X
Slots (3)
64-bit
PCI Bus
Marvell
SATA
Controller
32-bit
PCI Bus
GLAN
PCI Slots
Controller
(2)
Figure 1-1 . Intel 875P Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
1-4
Chapter 1: Introduction
1-3
Chassis Features
The SuperWorkstation 5033C-T is a mid-tower workstation type configuration.
The following is a general outline of the main features of the SC733T-350 chassis.
System Power
When configured as a SuperWorkstation 5033C-T, the SC733T-350 chassis includes a single low-noise 350W power supply.
Serial ATA Subsystem
The SC733T-350 chassis was designed to support up to four Serial ATA hard
drives. The Serial ATA drives are hot-swappable units. ATA/100 IDE drives are
also supported.
Control Panel
The SC733T-350's control panel provides important system monitoring and control information. LEDs indicate power on, network activity, hard disk drive activity
and overheat conditions. The control panel also includes a main power button
and a system reset button.
Rear I/O Panel
The rear I/O panel on the SC733T-350 provides seven motherboard expansion
slot, one COM port (another is internal), two USB ports, PS/2 mouse and keyboard ports, a parallel (printer) port, a graphics port and two Gb Ethernet ports.
(See Figure 1-2.)
1-5
SUPERWORKSTATION 5033C-T User's Manual
Cooling System
The SC733T-350 chassis has an innovative cooling design that features one 12cm exhaust fan and one 9-cm thermal cooling fan. The fans plug into headers
on the motherboard and operate at full rpm continuously.
Figure 1-2.
Keyboard
Mouse
Rear I/O Panel
Parallel (Printer) Port
USB 1/2 Ports
COM1 Port
VGA Port
1-6
GLAN Ports
Chapter 1: Introduction
1-4
Contacting Supermicro
Headquarters
Address:
Tel:
Fax:
Email:
Web Site:
SuperMicro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
+1 (408) 503-8008
marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
www.supermicro.com
Europe
Address:
Tel:
Fax:
Email:
SuperMicro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
+31 (0) 73-6416525
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Asia-Pacific
Address:
SuperMicro, Taiwan
D5, 4F, No. 16 Chien-Ba Road
Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3991
Web Site:
www.supermicro.com.tw
Technical Support:
Email:
support@supermicro.com.tw
Tel:
886-2-8228-1366, ext.132 or 139
1-7
SUPERWORKSTATION 5033C-T User's Manual
Notes
1-8
Chapter 2: System Installation
Chapter 2
System Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperWorkstation
5033C-T up and running. Following the steps in the order given should enable
you to have the system operational within a minimal amount of time. If your
system is not already fully integrated with a motherboard, processor, system
memory etc., please turn to the chapter or section noted in each step for details
on installing specific components.
2-2
Unpacking the SuperWorkstation 5033C-T
You should inspect the box the SuperWorkstation 5033C-T was shipped in and
note if it was damaged in any way. If the server itself shows damage, you should
file a damage claim with the carrier who delivered it.
Decide on a suitable location for setting up and operating the SuperWorkstation
5033C-T. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic fields are generated. You will also need it placed near a grounded power outlet.
Once the SuperWorkstation 5033C-T is placed in the appropriate location, slide
the locking tabs on each caster down to keep it stationary.
!
Warnings and Precautions!
!
- Ensure that the caster wheels on the workstation are locked.
- Review the electrical and general safety precautions in Chapter 4.
- Use a regulating uninterruptible power supply (UPS) to protect the server
from power surges, voltage spikes and to keep your system operating in
case of a power failure.
- Allow the power supply units and hot-swap Serial ATA drive to cool
before touching them.
- To maintain proper cooling, always keep all chassis panels closed and
all SATA carriers installed when not being serviced.
2-1
SUPERWORKSTATION 5033C-T User's Manual
2-3
Setting Up the System
You should first open the left side panel (when facing the front of the chassis) to
make sure the motherboard is properly installed and all connections have been
made.
Checking the Motherboard Setup
1. Accessing the inside of the 5033C-T (Figure 2-1)
Begin by removing the two screws from the back lip of the side cover (this
is the left cover when looking at the chassis from the front.) Grab the handle
and gently pull the side cover out to release it from its position. Once the side
cover is out of its position, slide the cover out of the chassis.
2. Check the CPU (processor)
You may have one processor already installed into the system board. The
processor should have its own heatsink attached. See Chapter 5 for instructions on processor installation.
3. Check the system memory
Your 5033C-T system may have come with system memory already installed.
Make sure all DIMMs are fully seated in their slots. For details on adding
system memory, refer to Chapter 5.
4. Installing add-on cards
If desired, you can install up to five add-on cards to the system. See Chapter
5 for details on installing PCI-X/PCI add-on cards.
5. Check all cable connections and airflow
Make sure all power and data cables are properly connected and not
blocking the airflow. See Chapter 5 for details on cable connections.
2-2
Chapter 2: System Installation
Figure 2-1. Accessing the Inside of the 5033C-T
2-3
SUPERWORKSTATION 5033C-T User's Manual
Checking the Drive Bay Setup
Next, you should check to make sure the peripheral drives and the Serial
ATA drive and Serial ATA backplane have been properly installed and all essential connections have been made.
1. Accessing the peripheral drive bays
To install or remove a component in the 3.5" and/or 5.25" drive bay(s), you will
need to remove the side chassis cover. See the installation and removal
sections for the peripheral drives in Chapter 6.
2. Check the Serial ATA disk drives
Depending upon your system's configuration, your system may have up to four
Serial ATA drives already installed. If you need to install or remove an SATA
drive, please refer to the appropriate section in Chapter 6.
3. Check the airflow
Cooling air is provided by a 9-cm internal cooling fan and a 12-cm exhaust fan.
The system component layout was carefully designed to promote sufficient
airflow throughout the chassis. Also note that all power and data cables have
been routed in such a way that they do not block the airflow generated by the
fan. Please keep this in mind when rerouting or adding/removing cables.
4. Supplying power to the system
The last thing you must do is to provide input power to the system. Plug the
power cord from the power supply unit into a high-quality power strip that offers
protection from electrical noise and power surges. It is recommended that you
use an uninterruptible power supply (UPS).
2-4
Chapter 3: System Interface
Chapter 3
System Interface
3-1
Overview
There are several LEDs on the control panel and one on each Serial ATA drive
carrier to keep you constantly informed of the overall status of the system as well
as the activity and health of specific components. There are also two buttons on
the chassis control panel. This chapter explains the meanings of all LED indicators and the appropriate response you may need to take.
3-2
Control Panel Buttons
There are two push-button buttons located on the front of the chassis.
These are (in order from left to right) a reset button and a power on/off
button.
RESET
!
RESET: The reset switch reboots the system.
!
POWER: This is the main power switch, which is used to apply or
turn off the main system power. Turning off system power with this button
removes the main power but keeps standby power supplied to the system.
3-1
SUPERWORKSTATION 5033C-T User's Manual
3-3
Control Panel LEDs
The control panel located on the front of the SC733T-350 chassis has four LEDs.
These LEDs provide you with critical information related to different parts of the
system. This section explains what each LED indicates when illuminated and
any corrective action you may need to take.
!
Power: Indicates power is being supplied to the system's power supply
units. This LED should normally be illuminated when the system is operating.
!
HDD: Channel activity for all HDDs. This light indicates SATA and (if
present) CD-ROM drive activity when flashing.
!
NIC: Indicates network activity on GLAN1 or GLAN2 when flashing .
!
OVERHEAT: Indicates an overheat condition in the chassis. This may be
caused by cables obstructing the airflow in the system, or the ambient room
temperature being too warm. You should also check to make sure that the
chassis cover is installed and that all fans are present and operating normally.
3-2
Chapter 3: System Interface
3-4
Serial ATA Drive Carrier LEDs
On the front of each Serial ATA drive carrier is a green LED. When illuminated,
it indicates drive activity. A connection to the Serial ATA backplane enables this
LED to blink on and off when that particular drive is being accessed.
3-3
SUPERWORKSTATION 5033C-T User's Manual
Notes
3-4
Chapter 4: System Safety
Chapter 4
System Safety
4-1
Electrical Safety Precautions
!
Basic electrical safety precautions should be followed to protect yourself from
harm and the SuperWorkstation 5033C-T from damage:
! Be aware of the locations of the power on/off switch on the chassis
as well as the room's emergency power-off switch, disconnection
switch or electrical outlet. If an electrical accident occurs, you can
then quickly remove power from the system.
! Do not work alone when working with high voltage components.
! Power should always be disconnected from the system when removing
or installing main system components, such as the motherboard,
memory modules and CD-ROM drive. When disconnecting power, you
should first power down the system with the operating system first and
then unplug the power cords of all the power supply units in the system.
! When working around exposed electrical circuits, another person who
is familiar with the power-off controls should be nearby to switch off
the power if necessary.
!
Use only one hand when working with powered-on electrical
equipment. This is to avoid making a complete circuit, which will
cause electrical shock. Use extreme caution when using metal tools,
which can easily damage any electrical components or circuit boards
they come into contact with.
! Do not use mats designed to decrease static electrical discharge as
protection from electrical shock. Instead, use rubber mats that have
been specifically designed as electrical insulators.
! The power supply power cords must include a grounding plug and must
be plugged into grounded electrical outlets.
4-1
SUPERWORKSTATION 5033C-T User's Manual
! Motherboard Battery: CAUTION - There is a danger of explosion if the onboard
battery is installed upside down, which will reverse its polarites. This
battery must be replaced only with the same or an equivalent type
recommended by the manufacturer. Dispose of used batteries according
to the manufacturer's instructions.
! CD-ROM Laser: CAUTION - this system may have come equipped with a
CD-ROM drive. To prevent direct exposure to the laser beam and hazardous
radiation exposure, do not open the enclosure or use the unit in any
unconventional way.
4-2
General Safety Precautions
!
Follow these rules to ensure general safety:
! Keep the area around the SuperWorkstation 5033C-T clean and free of clutter.
! The SuperWorkstation 5033C-T weighs approximately 40 lbs (18.2 kg) when
fully loaded. When lifting the system, two people at either end should lift
slowly with their feet spread out to distribute the weight. Always keep your
back straight and lift with your legs.
! Place the chassis top cover and any system components that have been
removed away from the system or on a table so that they won't
accidentally be stepped on.
!
While working on the system, do not wear loose clothing such as
neckties and unbuttoned shirt sleeves, which can come into contact
with electrical circuits or be pulled into a cooling fan.
!
Remove any jewelry or metal objects from your body, which are
excellent metal conductors that can create short circuits and harm you
if they come into contact with printed circuit boards or areas where
power is present.
4-2
Chapter 4: System Safety
4-3
ESD Precautions
!
Electrostatic discharge (ESD) is generated by two objects with different
electrical charges coming into contact with each other. An electrical
discharge is created to neutralize this difference, which can damage
electronic components and printed circuit boards. The following
measures are generally sufficient to neutralize this difference before
contact is made to protect your equipment from ESD:
! Use a grounded wrist strap designed to prevent static discharge.
! Keep all components and printed circuit boards (PCBs) in their
antistatic bags until ready for use.
! Touch a grounded metal object before removing the board from the
antistatic bag.
! Do not let components or PCBs come into contact with your clothing,
which may retain a charge even if you are wearing a wrist strap.
! Handle a board by its edges only; do not touch its components,
peripheral chips, memory modules or contacts.
! When handling chips or modules, avoid touching their pins.
! Put the motherboard and peripherals back into their antistatic bags
when not in use.
! For grounding purposes, make sure your computer chassis provides
excellent conductivity between the power supply, the case, the mounting
fasteners and the motherboard.
4-3
SUPERWORKSTATION 5033C-T User's Manual
4-4
Operating Precautions
!
Care must be taken to assure that the chassis cover is in place when the
5033C-T is operating to assure proper cooling. Out of warranty damage to
the 5033C-T system can occur if this practice is not strictly followed.
4-4
Chapter 5: Advanced Motherboard Setup
Chapter 5
Advanced Motherboard Setup
This chapter covers the steps required to install the P4SCT+II motherboard into
the SC733T-350 chassis, connect the data and power cables and install add-on
cards. All motherboard jumpers and connections are also described. A layout
and quick reference chart are included in this chapter for your reference. Remember to completely close the chassis when you have finished working with the
motherboard to better cool and protect the system.
5-1
Handling the P4SCT+II Motherboard
Electric-static discharge (ESD) can damage electronic components. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully (see previous chapter). To prevent the P4SCT+II motherboard from
bending, keep one hand under the center of the board to support it when handling.
The following measures are generally sufficient to protect your equipment from
electric static discharge.
Precautions
• Use a grounded wrist strap designed to prevent Electric Static Discharge
(ESD).
• Touch a grounded metal object before removing any board from its antistatic bag.
• Handle a board by its edges only; do not touch its components, peripheral chips, memory modules or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the motherboard, add-on cards and peripherals back into their antistatic bags when not in use.
• For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting
fasteners and the motherboard.
5-1
SUPERWORKSTATION 5033C-T User's Manual
Unpacking
The motherboard is shipped in antistatic packaging to avoid electrical static
discharge. When unpacking the board, make sure the person handling it is
static protected.
5-2
Motherboard Installation
This section explains the first step of physically mounting the P4SCT+II into the
SC733T-350 chassis. Following the steps in the order given will eliminate the
most common problems encountered in such an installation. To remove the
motherboard, follow the procedure in reverse order.
1.
Accessing the inside of the 5033C-T (see Figure 2-1)
Remove the two screws from the back lip of the side cover (this is the left
cover when looking at the chassis from the front.) Grab the handle and
gently pull the side cover out to release it from its position. Once the side
cover is out of its position, slide the cover out of the chassis.
2.
Removing the rear exhaust fan:
Y ou will need to remove the rear exhaust fan before installing the
motherboard. Refer to the appropriate section in Chapter 6 for details on
removing the rear exhaust fan.
3.
Mounting the motherboard onto the motherboard tray:
Carefully mount the motherboard to the motherboard tray by aligning
the board holes with the raised metal standoffs that are visible on the
bottom of the chassis. Insert screws into all the mounting holes on your
motherboard that line up with the standoffs and tighten until snug (if you
screw them in too tight, you might strip the threads). Metal screws provide
an electrical contact to the motherboard ground to provide a continuous
ground for the system. Finish by replacing the fan (reversing the procedure
in step 2) and the side cover of the chassis.
5-2
Chapter 5: Advanced Motherboard Setup
5-3
Connecting Cables
After the motherboard is installed, the next step is to connect the cables to the
board. These include the data (ribbon) cables for the peripherals and control
panel and the power cables.
Connecting Data Cables
The ribbon cables used to transfer data from the peripheral devices have
been carefully routed to prevent them from blocking the flow of cooling air
that moves through the system. If you need to disconnect any of these cables,
you should take care to keep them routed as they were originally after reconnecting them (make sure the red wires connect to the pin 1 locations). The following
data cables (with their locations noted) should be connected. (See the layout on
page 5-9 for connector locations.)
! IDE Device cable (J5)
! Floppy Device cable (J7)
! Serial ATA Device cables (JS1, JS2, JS3 and JS4)
! Serial ATA active LED cable (JS9)
! Control Panel cable (JF1)
Connecting Power Cables
The P4SCT+II has a 24-pin primary power supply connector ("ATX Power") at J20
for connection to the ATX power supply. In addition, there is a 4-pin secondary
power connector at J21 that also must be connected to your power supply. See
Chapter 5 for power connector pin definitions.
Connecting the Control Panel
JF1 contains header pins for various front control panel connectors. See
Figure 5-1 for the pin locations of the various front control panel buttons
and LED indicators.
All JF1 wires have been bundled into a single ribbon cable to simplify this
connection. Make sure the red wire plugs into pin 1 as marked on the
board. The other end connects to the Control Panel PCB board, located just
behind the system status LEDs on the chassis. See Chapter 5 for details
and pin descriptions.
5-3
SUPERWORKSTATION 5033C-T User's Manual
Figure 5-1. Control Panel Header Pins
20
19
NMI
Ground
X
X
Power LED
Vcc
IDE LED
Vcc
LAN1 LED
Vcc
LAN2 LED
Vcc
Overheat LED
Vcc
X
X
Ground
Ground
2
Reset
Reset Button
Pwr
Power Button
1
JF1
5-4
I/O Ports
The I/O ports are color coded in conformance with the PC 99 specification.
See Figure 5-2 below for the colors and locations of the various I/O ports.
Figure 5-2. I/O Port Locations
Mouse
(Green)
Keyboard
Parallel Port (Burgundy)
USB 0/1 Ports COM1 Port (Turquoise)
VGA Port (Blue)
GLAN1
GLAN2
(Purple)
Note: The COM2 port is a header on the motherboard, located near the
ATX power connector.
5-4
Chapter 5: Advanced Motherboard Setup
5-5
!
Installing Processors
Avoid placing direct pressure to the top of the processor
package. Always remove the power cord first before adding,
removing or changing any hardware components.
Processor Support
The P4SCT+II has a single 478-pin microPGA socket, which supports Intel
Pentium 4 processors on .013 micron process.
1. Begin by installing the CPU heatsink mechanism by screwing it into the holes
on either side of the CPU socket.
2. Lift the lever on the CPU socket.
3. Install the CPU in the socket by aligning the pins to the holes in the socket.
Make sure that Pin 1 of the CPU is seated on Pin 1 of the socket (both corners
are marked with a triangle).
4. Press the lever down until you hear it *click* into the locked position.
5. To install the heatsink, please refer to the instructions that came with the Intel
heatsink, which you should have received in the same package as the Pentium
4 processor. (You may also refer to http://www.intel.com/support/processors/
manuals/p4pman2.htm).
Figure 5-3.
478-pin Socket: Empty and with Processor Installed
5-5
SUPERWORKSTATION 5033C-T User's Manual
5-6
Installing Memory
!
CAUTION! Exercise extreme care when installing or removing DIMM modules to prevent any possible damage.
1.
Memory support
The P4SCT+II supports 4 GB of dual-channel, ECC or non-ECC unbuffered
DDR-400/333/266 SDRAM. You must populate both DIMM0A and DIMM1A
and/or DIMM0B and DIMM1B with the same size and type of memory
modules. This will result in dual channel (two-way interleaved) operation,
which is faster than single channel operation.
2.
Installing memory modules
Insert each memory module vertically. Pay attention to the notch along the
bottom of the module to prevent inserting it incorrectly. Gently press down
on the DIMM module until it snaps into place in the slot (see Figure 5-4).
Memory Speeds
Host Clock
(MHz)
FSB (MHz)
100
400
133
533
200
800
DRAM Data Shown during
(MT/s)
POST
266
333
400
266
333
400
266
333
400
DDR266
DDR266
DDR266
DDR266
DDR333
DDR333
DDR266
DDR320*
DDR400
* The BIOS displays DDR320 due to a chipset limitation.
Figure 5-4. DIMM Installation
To Install: Insert module vertically and press down until it snaps into place. Pay attention
to the bottom notch.
To Remove: Use your thumbs to gently push each release tab outward to free the DIMM
from the slot.
5-6
Chapter 5: Advanced Motherboard Setup
Figure 5-5. Top View of DIMM Slot
5-7
1.
Adding PCI Cards
PCI-X/PCI card installation
The P4SCT+II supports the use of three 64-bit, 66 MHz (3.3V) PCI-X add-on cards
and two 32-bit, 33 MHz (5V) PCI add-on cards. To install an add-on card, begin
by removing the I/O shield for the slot you wish to populate. Fully seat the card
into the card slot on the motherboard, pushing down with your thumbs evenly on
both sides of the card. Finish by using a screw to secure the top of the card
shield to the rear of the chassis. The I/O shields protect the motherboard and
its components from EMI and aid in proper ventilation, so make sure there is
always a shield covering each unused PCI-X/PCI slot.
5-7
SUPERWORKSTATION 5033C-T User's Manual
5-8
Motherboard Details
Figure 5-6. P4SCT+II Layout
(not drawn to scale)
USB1/2
J17 (PWR LED)
J10
COM2
J21
ATX Power Connector
J20
WOR
Super I/O
J11
GLAN Controller
82547
CPU/CH FAN1
JPWAKE
JPUSB
Keyboard/
Mouse
+12V Power Connector
JP20
JP8 (WD)
Parallel Port
JP2
JP1
COM1 J9
CPU
478 mPGA
J8
MCH
VGA
OH/CH FAN5
GLAN1
DIMM0A
BANK0
DIMM0B
GLAN2
DIMM1A
BANK1
DIMM1B
J3
GLAN Controller
SATA PORTS (Intel)
JF1
J4
AGP
82541
J16 (IR)
CH FAN3
6300ESB
Hance Rapids
PCI-X 2
CH FAN2
PCI-X 1
LE2
WOL
JPL2
P4SCT+II
JPS1
BIOS
JS3
PCI 1
Marvell
USB3/4
(SATA Controller)
JS2
IDE #2
88SX5040
IDE #1
BATTERY
FLOPPY
RAGE XL
SPEAKER
®
SUPER
JS4
J15
J7
J5
J2
PCI 2
J33
JS1
CH FAN4
J36
J18
J37-SATA LED (Intel)
JS9-SATA LED (Marvell)
Jumpers not indicated are for test purposes only.
5-8
JL1
SATA PORTS (Marvell)
JBT1 (CMOS CLR)
PCI-X 3
Chapter 5: Advanced Motherboard Setup
P4SCT+II Quick Reference
Jumpers
Description
Default Setting
J18
J33
J36
JBT1
JP1/JP2
JP8
JP20
JPL2
JPS1
JPUSB
JPWAKE
Speaker
VGA Enable/Disable
Keylock Header
CMOS Clear
CPU Clock Speed
Watch Dog Reset
Power Force On
GLAN2 Enable/Disable
JS1-4 SATA En/Dis
USB1/2 Wake Up En/Dis
Keyboard Wake Up
Pins 3-4 (Int. Buzzer)
Pins 1-2 (Enabled)
Open (Disabled)
See Section 5-10
Pins 1-2 (Auto)
Pins 1-2 (WD Reset)
Open (Disabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Disabled)
Pins 1-2 (Disabled)
Connectors
Description
DIMM0A/0B/1A/1B
Fans 1-5
GLAN1/2
J2/J5
J3/J4
J7
J8
J9/J10
J11
J15
J16
J17
J20
J21
J36
J37
JF1
JL1
JP17
JS1-4
JS9
USB 1/2
USB 3/4
WOL
WOR
Memory (DIMM) Slots
CPU/CH Fan1, CH Fan2, 3, 4, OH Fan/CH Fan 5
Gigabit LAN Ports
IDE1/2 Ports
SATA Connectors 1/2 (Intel Controller)
Floppy Disk Drive Connector
Parallel Printer Port
COM1(J9), COM2(J10)
Keyboard/Mouse Connector
System Management Bus
Infrared Header
Power LED
ATX Power Connector
+12V Power Connector
Keylock Connector
SATA LED Header (Intel ports)
Front Control Panel
Chassis Intrusion Header
Power LED
SATA Connectors 1-4 (Marvell Controller)
SATA LED Header (Marvell ports)
Backpanel Universal Serial Ports 1/2
Universal Serial Ports 3/4 (for front side access)
Wake-On-LAN
Wake-On-Ring Header
5-9
SUPERWORKSTATION 5033C-T User's Manual
5-9
Connector
Definitions
ATX Power Supply 24-pin Connector
Pin Definitions
Power Supply Connectors
The primary power supply connector
on the P4SCT+II meets the SSI
(Superset ATX) 24-pin specification. Refer to the table on the right
for the pin definitions of the ATX
24-pin power connector. You
must also connect the 4-pin J21
power connector to your power
supply. Refer to the table below
right for the J24 (12V) connector.
Pin Number
13
14
15
16
17
18
19
20
21
22
23
24
Definition
+3.3V
-12V
COM
PS_ON#
COM
COM
COM
Res(NC)
+5V
+5V
+5V
COM
+12V 4-pin PWR
Connector
(J21)
Required
Important: you must connect J21 to
your power supply to meet the ATX
Pin Number Definition
1
+3.3V
2
+3.3V
3
COM
4
+5V
5
COM
6
+5V
7
COM
8
PW R_OK
9
5VSB
10
+12V
11
+12V
12
+3.3V
Connection
Pins # Definition
1 & 2 Ground
3&4
+12 V
safety requirements.
PW_ON Connector
PW_ON
Pin Definitions
(JF1)
The PW_ON connector is located on
pins 1 and 2 of JF1. This header
should be connected to the chassis
power button, which you may also
configure to put the system into suspend mode (see the Power Button
Mode setting in BIOS). To turn off
the power when the suspend mode is
enabled, depress the power button
for at least 4 seconds. See the table
on the right for pin definitions.
5-10
Pin
Number Definition
1
PW_ON
2
+3V
Chapter 5: Advanced Motherboard Setup
Reset Connector
The reset connector is located on
pins 3 and 4 of JF1 and attaches
to the reset switch on the computer chassis. See the table on
the right for pin definitions.
Overheat LED (OH)
Reset Pin
Definitions
(JF1)
Pin
Number Definition
3
Reset
Ground
4
Overheat (OH) LED
Pin Definitions
(JF1)
Connect an LED to the OH connection on pins 7 and 8 of JF1 to provide advanced warning of chassis
overheating. Refer to the table on
the right for pin definitions.
GLAN2 LED
The GLAN2 LED connection is located on pins 9 and 10 of JF1. Attach the GLAN2 LED cable to display GLAN2 activity. Refer to the
table on the right for pin definitions.
GLAN1 LED
The GLAN1 LED connection is located on pins 11 and 12 of JF1. Attach the GLAN1 LED cable to display GLAN1 activity. Refer to the
table on the right for pin definitions.
5-11
Pin
Number Definition
7
Vcc
8
GND
GLAN2 LED
Pin Definitions
(JF1)
Pin
Number Definition
9
Vcc
10
GND
GLAN1 LED Pin
Definitions
(JF1)
Pin
Number Definition
11
Vcc
12
GND
SUPERWORKSTATION 5033C-T User's Manual
IDE LED
IDE Activity LED
Pin Definitions
(JF1)
The IDE LED is located on pins 13
and 14 of JF1. This LED is used to
display all IDE and SATA activity
on all drives. See the table on the
right for pin definitions.
Power_LED Connector
The Power LED connector is located
on pins 15 and 16 of JF1 (or you may
use J17 for a 3-pin connector). This
connection is used to provide LED
indication of power being supplied to
the system. See the table on the
right for pin definitions.
NMI Button
The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin definitions.
Pin
Number Definition
13
+5V
14
HD Activity
PWR_LED Pin Definitions
(JF1)
Pin
Number
Definition
15
Vcc
16
Control
J17
Pin Definitions
Pin
Number
Definition
1
+5V
2
Key
3
Ground
NMI Button Pin
Definitions (JF1)
Pin
Number
Definition
19
Ground
20
Control
SMB Header
Pin Definitions (J15)
SMB Header
A System Management Bus header
is located at J15. Connect the appropriate cable here to utilize SMB
on your system.
5-12
Pin
Number
1
2
3
4
Definition
Data
Ground
Clock
No Connection
Chapter 5: Advanced Motherboard Setup
IR Connector
Infrared Pin
Definitions
(J16)
Pin
Number Definition
+5V
1
CIRRX
2
IRRX
3
Ground
4
IRTX
5
NC
6
The infrared connector is located on
J16. See the table on the right for
pin definitions. See the Technical
Support section of our web page for
information on the infrared devices
you can connect to the system.
Serial Ports
Serial Port Pin Definitions
(COM1, COM2)
Two serial ports are included on the
motherboard: COM1 is a port located beside the mouse/keyboard
ports and COM2 is a header located
on the motherboard near the J20
power connector. See the table on
the right for pin definitions.
Pin Number
1
2
3
4
5
Definition Pin Number Definition
CD
6
DSR
RD
7
RTS
TD
8
CTS
DTR
9
RI
Ground
10
NC
Note: Pin 10 is included on the header but
not on the port.
NC indicates no connec-
tion.
Fan Headers
Fan Header Pin Definitions
(CPU/ Chassis and Overheat)
There are six fan headers on the
P4SCT+II, which are designated
CPU/Chassis Fan1, Chassis Fan2,
Chassis Fan3, Chassis Fan4 and OH
(Overheat)/Chassis Fan5. (Chassis
Fan 3 and Chassis Fan 4 are not
monitored by BIOS.) Connect the
fan on your CPU heatsink to the
CPU/Chassis Fan1 header. See the
table on the right for pin definitions.
5-13
Pin
Number
1
2
3
Definition
Ground (black)
+12V (red)
Tachometer
Caution: These fan headers are DC power.
SUPERWORKSTATION 5033C-T User's Manual
Chassis Intrusion
The Chassis Intrusion header is designated JL1. See the board layout in
Chapter 1 for the location of JL1 and
the table on the right for pin definitions.
Chassis Intrusion
Pin Definitions (JL1)
Pin
Number
Definition
1
Intrusion Input
Ground
2
Wake-On-LAN
The Wake-On-LAN header is designated WOL on the motherboard.
See the table on the right for pin
definitions. You must enable the
LAN Wake-Up setting in BIOS to
use this function. (You must also
have a LAN card with a Wake-OnLAN connector and cable to use
this feature.)
Wake-On-LAN Pin
Definitions (WOL)
Pin
Number
1
2
3
Definition
+5V Standby
Ground
Wake-up
Wake-On-Ring
The Wake-On-Ring header is designated WOR. This function allows your
computer to receive and be "awakened" by an incoming call when in the
suspend state. See the table on the
right for pin definitions. You must also
have a WOR card and cable to use this
feature.
ATX PS/2 Keyboard and
PS/2 Mouse Ports
Wake-On-Ring Pin Definitions
(WOR)
Pin
Number
1
2
Definition
Ground
Wake-up
PS/2 Keyboard
and Mouse Port
Pin Definitions
(J11)
The ATX PS/2 keyboard and the
PS/2 mouse are located on J11.
The mouse port is above the keyboard port. See the table on the
right for pin definitions.
5-14
Pin
Number Definition
Data
1
NC
2
Ground
3
VCC
4
Clock
5
NC
6
Chapter 5: Advanced Motherboard Setup
Universal Serial Bus
(USB)
USB1/2 Pin Definitions
There are two Universal Serial Bus
ports located on the I/O panel and an
additional two USB headers located
on the motherboard. These headers, labeled USB3/4, can be used to
provide front side chassis access
(cables not included). See the tables
on the right for pin definitions.
Pin# Definition
1
+5V
2
P03
P0+
4 Ground
USB3/4 Pin Definitions
Pin
Number
1
3
5
7
Definition
+5V
POPO+
Ground
Pin
Number
2
4
6
8
10
Definition
+5V
POPO+
Ground
Ground
GLAN1/2 (Ethernet) Ports
Two Ethernet ports (designated
GLAN1 and GLAN2) are located
beside the VGA port on the IO
backplane. These ports accept
RJ45 type cables.
SATA LED (Marvell)
SATA LED Pin Definitions
(JS9)
The SATA LED header located on
JS9 is used to display all SATA activity on the JS1-JS4 SATA ports
(Marvell SATA controller). See the
table on the right for pin definitions.
Pin #
1
2
3
4
5
Definition
SATA1
SATA2
SATA3
SATA4
SATA LED
Comm
Pin #
6
7
8
9
10
Intel's SATA LED
Pin Definitions
(J37)
SATA LED (Intel)
The SATA LED header located on
J37 is used to display all SATA activity on the J3 and J4 SATA ports
(Intel SATA controller). See the
table on the right for pin definitions.
5-15
Pin
Number Definition
(I-)SATA1
1
(I-)SATA2
2
NC
3
NC
4
NC
5
Definition
NC
NC
NC
NC
Key
SUPERWORKSTATION 5033C-T User's Manual
5-10 Jumper Settings
Explanation of
Jumpers
To modify the operation of the
motherboard, jumpers can be used
to choose between optional settings. Jumpers create shorts between two pins to change the
function of the connector. Pin 1 is
identified with a square solder pad
on the printed circuit board. See
the motherboard layout pages for
jumper locations.
Connector
Pins
3
2
1
3
2
1
Jumper
Cap
Setting
Pin 1-2 short
No te : On a two-pin jumper,
"Closed" means the jumper is on
both pins and "Open" means the
jumper is either on only one pin or
completely removed.
CMOS Clear
JBT1 is used to clear CMOS (which will also clear any passwords). Instead of
pins, this jumper consists of contact pads to prevent accidentally clearing the
contents of CMOS.
To clear CMOS, 1) First unplug the power cord(s) 2) With the power disconnected,
short the CMOS pads with a metal object such as a small screwdriver 3) Remove
the screwdriver (or shorting device) 4) Reconnect the power cord(s) and power on the
system.
Note: Do not use the PW_ON connector to clear CMOS.
Front Side Bus Speed
Front Side Bus Speed
(JP1, JP2)
JP1 and JP2 are used to set the system (front side) bus speed for the
processors. It is best to keep these
jumpers set to Auto. These jumpers
are used together with the CPU
Clock setting in BIOS. See the table
on the right for jumper settings.
5-16
JP1
Pins 1-2
Pins 2-3
NC
NC
Pins 2-3
JP2
Pins 1-2
Pins 2-3
Pins 2-3
NC
NC
FSB Speed
Auto
100 MHz (x4)
133 MHz (x4)
Reserved
200 MHz (x4)
Note: NC stands for "No Connection".
Chapter 5: Advanced Motherboard Setup
USB Wake-Up
Use JPUSB1 to enable or disable
USB Wake-Up, which allows you
to wakeup the system by depressing a key on the keyboard or
by clicking the mouse when either
is connected to the USB1 or USB2
port. Enable the jumper to allow
the system to be woken up from
an S1 or S3 state in Windows OS.
See the table on the right for
jumper settings. This feature
works with the USB1 and USB2
ports only.
USB Wake-Up
Jumper Settings
(JPUSB1)
Jumper
Position
1-2
2-3
Definition
Disabled
Enabled
Watch Dog Enable/Disable
JP8 enables controls the Watch
Dog function, a system monitor
that takes action when a software
application freezes the system.
Pins 1-2 will have WD reset the
system if a program freezes. Pins
2-3 will generate a non-maskable
interrupt for the program that has
frozen. See the table on the right
for jumper settings. Watch Dog
must also be enabled in BIOS.
Watch Dog
Jumper Settings (JP8)
Jumper
Position
Pins 1-2
Pins 2-3
Open
Definition
WD to Reset
WD to NMI
Disabled
Note: when Watch Dog is enabled, the user must
write their own application software to disable
the Watch Dog Timer.
Speaker Jumper
Speaker
Jumper Settings (J18)
The speaker jumper is located on
J18 and allows you to choose between using the internal or external speakers. For the internal
speaker, jump pins 3 and 4. To
use an external speaker, place the
speaker cable's header on all four
pins See the table on the right.
5-17
Definition
Pins
1 through 4 External Spkr
3 and 4 Internal Spkr
SUPERWORKSTATION 5033C-T User's Manual
Keyboard Wake-Up
The JPWAKE jumper is used to allow the system to be woken up by
depressing a key on the keyboard
from an S1 or S3 state in Windows OS. See the table on the
right for jumper settings. Your
power supply must meet ATX
specification 2.01 or higher and
supply 720 mA of standby power
to use this feature.
GLAN2 Enable/Disable
Change the setting of jumper JPL2 to
enable or disable the onboard
GLAN2 port on the motherboard.
See the table on the right for jumper
settings. The default setting is Enabled. (For LAN1, please change
the setting in the BIOS.)
Keyboard Wake-Up
Jumper Settings
(JPWAKE)
Jumper
Position
1-2
2-3
Definition
Disabled
Enabled
GLAN2
Enable/Disable
Jumper Settings
(JPL2)
Jumper
Position
Pins 1-2
Pins 2-3
Definition
Enabled
Disabled
VGA Enable/Disable
Jumper Settings
(J33)
VGA Enable/Disable
J33 allows you to enable or disable
the VGA port. The default position
enabled. See the table on the right
for jumper settings.
Keylock Enable/Disable
The Keylock header is located at
J36. Close the jumper to enable the
Keylock function and leave the
jumper open (off) to disable it. The
default setting is open. See the
table on the right for jumper settings.
5-18
Jumper
Position
1-2
2-3
Definition
Enabled
Disabled
Keylock
Enable/Disable
Jumper Settings
(J36)
Jumper
Position
On
Off
Definition
Enabled
Disabled
Chapter 5: Advanced Motherboard Setup
SATA Enable/Disable
JSP1 is used to enable or disable
Marvell's Serial ATA Controller. See
the table on right for pin definitions.
5-11 Onboard Indicators
Standby Power LED
The Standby Power LED indicator is
designated LE2. When the Standby
PWR LED is on, it indicates the
system standby power is on.
5-19
SATA Enable/Disable
Jumper Settings (JPS1)
Jumper
Position
1-2
2-3
Definition
Enabled
Disabled
SUPERWORKSTATION 5033C-T User's Manual
5-12 Parallel Port, Floppy/IDE Hard Drive and AGP
Connections
Use the following information to connect the floppy and hard disk drive cables.
•
A floppy disk drive cable has seven twisted wires.
•
A red mark on a wire typically designates the location of pin 1.
•
A single floppy disk drive ribbon cable has 34 wires and two connectors to
provide for two floppy disk drives. The connector with twisted wires always
connects to drive A, and the connector that does not have twisted wires
always connects to drive B.
• The 80-wire ATA100/66 IDE hard disk drive cable that came with your system
has two connectors to support two drives. This special cable should be used
to take advantage of the speed this new technology offers. The blue connector
connects to the onboard IDE connector interface and the other connector(s)
to your hard drive(s). Consult the documentation that came with your disk
drive for details on actual jumper locations and settings for the hard disk drive.
Parallel Port Connector
Parallel (Printer) Port Pin Definitions
(J8)
The parallel port is located on J8.
See the table on the right for pin
definitions.
5-20
Pin Number
1
3
5
7
9
11
13
15
17
19
21
23
25
Function Pin Number Function
Strobe2
Auto FeedData Bit 0
4
ErrorData Bit 1
6
InitData Bit 2
8
SLCT INData Bit 3
10
GND
Data Bit 4
12
GND
Data Bit 5
14
GND
Data Bit 6
16
GND
Data Bit 7
18
GND
ACK
20
GND
BUSY
22
GND
PE
24
GND
SLCT
26
NC
Chapter 5: Advanced Motherboard Setup
Floppy Connector
The floppy connector is located
on J7. See the table on the right
for pin definitions.
Floppy Connector Pin Definitions (J7)
Pin Number
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Function Pin Number
GND
2
GND
4
Key
6
GND
8
GND
10
GND
12
GND
14
GND
16
GND
18
GND
20
GND
22
GND
24
GND
26
GND
28
GND
30
GND
32
GND
34
Function
FDHDIN
Reserved
FDEDIN
IndexMotor Enable
Drive Select BDrive Select AMotor Enable
DIRSTEPWrite DataWrite GateTrack 00Write ProtectRead DataSide 1 SelectDiskette
IDE Connectors
There are no jumpers to configure the onboard IDE interfaces
J2 and J5. See the table on the
right for pin definitions. You
must use the ATA100/66 cable
included with your system to
benefit from the ATA100/66
technology.
IDE Connector Pin Definitions
(J2, J5)
Pin Number
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
5-21
Function
Pin Number
Function
Reset IDE
2
GND
Host Data 7
4
Host Data 8
Host Data 6
6
Host Data 9
Host Data 5
8
Host Data 10
Host Data 4
10
Host Data 11
Host Data 3
12
Host Data 12
Host Data 2
14
Host Data 13
Host Data 1
16
Host Data 14
Host Data 0
18
Host Data 15
GND
20
Key
DRQ3
22
GND
I/O Write24
GND
I/O Read26
GND
IOCHRDY
28
BALE
DACK330
GND
IRQ14
32
IOCS16Addr 1
34
GND
Addr 0
36
Addr 2
Chip Select 0
38
Chip Select 1Activity
40
GND
SUPERWORKSTATION 5033C-T User's Manual
1.5V 8xAGP Pro Slot
The P4SCT+II includes an 8xAGP Pro slot for high-performance video cards. It
is backward compatible with 4xAGP and 2xAGP graphics cards.
To install a VGA card, power down the system and remove the I/O shield corresponding to the 8xAGP Pro slot. Push the AGP card down making sure that the
golden tab does not show. Finish by screwing the AGP card onto the
motherboard. Replace all chassis covers before restoring power to the system.
Figure 5-7. 8xAGP Pro Slot
5-22
Chapter 6: Advanced Chassis Setup
Chapter 6
Advanced Chassis Setup
This chapter covers the steps required to install components and perform simple
maintenance on the SC733T-350 chassis. Following the component installation
steps in the order given will eliminate most common problems. If some steps are
unnecessary, skip ahead to the next step.
Tools Required
The only tool you will need is a Philips screwdriver.
6-1
Static-Sensitive Devices
Static electrical discharge can damage electronic components. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them
very carefully. The following measures are generally sufficient to protect your
equipment from static discharge.
Precautions
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing any board from its antistatic bag.
• Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the motherboard, add-on cards and peripherals back into their antistatic bags when not in use.
• For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the motherboard.
Unpacking
The motherboard is shipped in antistatic packaging. When unpacking the
board, make sure the person handling it is static protected.
6-1
SUPERWORKSTATION 5033C-T Manual
6-2
Front Control Panel
The front control panel must be connected to the JF2 connector on the motherboard to provide you with system status and alarm indications. A ribbon cable
has bundled these wires together to simplify this connection. Connect the cable
from JF2 on the motherboard (making sure the red wire plugs into pin 1) to the
appropriate comnnector on the front control panel PCB (printed circuit board).
Pull all excess cabling over to the control panel side of the chassis. The LEDs
inform you of system status - see Figure 6-1 for details. Figure 6-2 shows the
SC733T-350 features included on the front of the chassis. See Chapter 5 for
details on JF2.
Figure 6-1.
Power
Front Control Panel LEDs
Indicates power is being supplied to the system.
HDD
Indicates SATA hard disk/CD-ROM drive activity.
NIC
Indicates network activity on either GLAN port.
Overheat
Indicates an overheat condition in the chassis.
6-2
Chapter 6: Advanced Chassis Setup
Figure 6-2.
Chassis Front View
5.25" Drive Bays
Floppy Drive Bay
Main Power
System Reset
Front Side USB
System LEDs
SATA Active LED
SATA Drive Configuration
Drive IDs are marked on the
Front Bezel Lock
front bezel. From bottom
to top they are Drive 0,
Drive 1, Drive 2 and Drive 3
6-3
SUPERWORKSTATION 5033C-T Manual
Figure 6-3.
Chassis Rear View
Power Supply Fan
Power Supply
12-cm Exhaust Fan
IO Backplane
PCI Expansion Slots
6-4
Chapter 6: Advanced Chassis Setup
6-3
System Fans
A 9-cm chassis cooling fan housed in a fan duct is located just below the
peripheral drive bays to provide cool air intake for the system. A 12-cm exhaust
fan at the rear of the chassis pulls the cool air through the system and expels
the hot air.
Fan Failure
Under normal operation, the chassis, the exhaust and the power supply fans all
run continuously. If any of these three fans fail, the system must be powered
down before replacing them.
Replacing System Fans
1.
Identifying and accessing the fan
First, inspect the back of the chassis to see if it is the 12-cm fan that has
failed. Power down the system and remove the left chassis cover by first
removing the two screws from the back lip of the cover. Push in the release
tab on the cover and push the cover toward the rear of the chassis until it
stops (after moving about ½ inch). Then lift the cover out and away from the
chassis. (See Figure 2-1 for accessing the inside of the chassis.)
2.
Removing the fan duct assembly
9-cm fan: After removing the side chassis cover, release the clips that secure
the fan duct to the chassis. You can then pull the fan duct out from its
location in the chassis. Remove the four screws at the front of the fan duct
that hold the fan in place. Then release the two fasteners along the side of
the fan duct. You can now separate it into two pieces and easily remove the
fan (see Figure 6-4). Add a new fan of the same type (see step 3).
The 12-cm exhaust fan is also in a housing that can be removed from the
chassis after removing the left chassis cover (see Figure 6-5).
3.
Installing a new fan
Replace the failed fan with an identical one (available from Supermicro).
After the new fan has been installed into the fan duct, reassemble the fan
duct and perform the removal procedure in reverse to install the entire fan
duct assembly back into the chassis. Make sure the wiring for the fan is
also reattached to its proper header. Finish by replacing the left chassis
cover, then restore power to the system. Check that the replaced fan is
working properly.
6-5
SUPERWORKSTATION 5033C-T Manual
Figure 6-4. Removing the Fan Duct Assembly (9-cm Fan)
Figure 6-5. Removing the 12-cm Exhaust Fan
6-6
Chapter 6: Advanced Chassis Setup
6-4
Drive Bay Installation
A bezel covers the front of the chassis but does not need to be removed to
access the drives. If you wish to remove the bezel piece, push on the
three tabs on the inside left side lip of the front chassis cover. Then
slightly swing out the same (left) side of the cover - about ½ inch only.
Remove by pushing on the open side of the cover to remove it from the
chassis (do not try to swing or pull it straight out after opening the left side.
Serial ATA Drives
After unlocking the Serial ATA (SATA) drive bay door, swing it open to access
the SATA drive. The drive IDs are preconfigured as 0 through 3 in order from
bottom to top.
!
Important!
Use extreme caution when working around
the SATA backplane. Do not touch the backplane with
any metal objects and make sure no ribbon cables touch
the backplane or obstruct the airflow holes in the SATA
backplane. Regardless of how many SATA hard drives are
installed, all four SATA drive carriers must remain in the
drive bays to promote proper airflow.
1.
Installing/removing hot-plug SATA drives:
The four SATA drive carriers are all easily accessible at the front of the
chassis. These SATA drives are hot-pluggable, meaning they can be
removed and installed without powering down the system. To remove a
carrier, first open the front bezel then push the release button located beside
the drive LEDs. Swing the colored handle fully out and use it to pull the unit
straight out (see Figure 6-6).
Note: Your operating system must have RAID support to enable the hot-plug
capability of the SATA drives.
6-7
SUPERWORKSTATION 5033C-T Manual
2.
Mounting an SATA drive in a drive carrier:
The SATA drives are mounted in drive carriers to simplify their installation
and removal from the chassis. These carriers also work to promote
proper airflow for the system. For this reason, even carriers without
SATA drives must remain in the server. If you need to add a new SATA
drive, insert the drive into the carrier with the printed circuit board side
facing down so that the mounting holes align with those in the carrier.
Secure the drive to the carrier with four screws.
Figure 6-6. Removing an SATA Drive Carrier
6-8
Chapter 6: Advanced Chassis Setup
3.
SATA backplane:
All four SATA drives plug into the SATA backplane. There are two
jumpers and two headers on the SATA backplane, as noted below. A
ribbon cable from JA1 on the motherboard should be connected to the
JP26 connector on the SATA backplane. There are also two power
connectors on the backplane - both should be connected. See Figure 6-7 for
the locations of backplane connectors - the reverse side of the backplane has
four channel connectors that the SATA drives plug into when inserted with a
SATA drive carrier. See Figure 6-2 for drive number configuration. You
cannot cascade the SATA backplane.
Jumper
JP18
JP25
Description
Buzzer Reset
OH Temperature
JP26
JP28
SATA Drive Activity
Fan Sense
Setting
Alarm Reset Header
Open: 45 degrees C
Pins 1-2: 50 degrees C (default)
Pins 2-3: 55 degrees C
Drive Activity
Pins 1-2: Enable
Pins 2-3: Disable (default)
Figure 6-7. SATA733 Backplane
Power Connections
SATA Channel Connections
6-9
SUPERWORKSTATION 5033C-T Manual
Installing Components in the 5.25" Drive Bays
1.
Drive bay configuration
The 5033C-T has two 5.25" drive bays above the SATA drive bays. Components such as a floppy drive, IDE hard drives or CD-ROM drives can be
installed in these 5.25" drive bays.
2.
Mounting components in the drive bays
First power down the system and then remove the top/left chassis cover
to access the drive components. With the cover off, remove the two or
four screws that secure the drive carrier to the chassis (one side only)
then push the entire empty drive carrier out from the back.
Adding a CD-ROM drive: remove the guide plate from right side of the
empty drive carrier and screw it into the right side of the CD-ROM drive
using the holes provided (see Figure 6-8). Then slide the CD-ROM into the
bay and secure it to the chassis with the drive carrier screws you first
removed. Attach the power and data cables to the drive. Replace the top/left
chassis cover before restoring power to the system.
Adding an IDE or floppy drive: to add one of these drives, install it into one of
the removed empty drive carriers with the printed circuit board side toward the
carrier so that the drive's mounting holes align with those in the carrier.
Secure the drive to the carrier with four screws then slide the assembly into
the bay and secure it to the chassis with the drive carrier screws you first
removed. Attach the power and data cables to the drive. Replace the top/left
chassis cover before restoring power to the system.
Note: A red wire typically designates the location of pin 1. You should keep
the drive carriers inserted in any unused drive bays to reduce EMI and noise
and to facilitate the airflow inside the chassis.
Figure 6-8. Adding a Component Without a Drive Carrier
6-10
Chapter 6: Advanced Chassis Setup
6-5
Power Supply
The 5033C-T has a single 350W power supply that features noise-suppression
technology for silent operation. The power supply has the capability to automatically sense and operate at 100 or 240V AC. This power supply also has the PFC
(Power Factor Correction) feature built in.
Replacing the Power Supply
1.
Accessing the power supply:
After powering down the system, you’ll need to remove the left chassis
cover to access the power supply for removal.
2.
Removing the power supply:
First, unplug the power cord from the power supply. Then remove the
power supply connectors going to the motherboard and the SATA
backplane. Finally, remove the screws that secure the unit to the mounting brackets in the chassis and then pull the unit completely out.
3.
Installing a new power supply module:
Replace the failed unit with another unit having the exact same part number
(PWS-0059). Gently but firmly push the new unit all the way into the open
bay. Secure it to the mounting brackets in the chassis with the screws
provided. Connect two power cables to the SATA backplane and two to the
motherboard (ATX PWR CONN and J21 connectors). Finish by replacing the
chassis left cover and then restoring power to the system.
6-11
SUPERWORKSTATION 5033C-T Manual
Notes
6-12
Chapter 7: BIOS
Chapter 7
BIOS
7-1
Introduction
This chapter describes the AwardBIOS for the P4SCT+II. The Award ROM BIOS
is stored in a Flash chip and can be easily upgraded using a floppy disk-based
program.
Note: Due to periodic changes to the BIOS, some settings may have been added
or deleted and might not yet be recorded in this manual. Refer to the Manual
Download area of our web site for any changes to BIOS that are not reflected in
this manual.
System BIOS
The BIOS is the Basic Input Output System used in all IBM® PC, XT™, AT®, and
PS/2 ® compatible computers. The AwardBIOS Flash chip stores the system
parameters, such as amount of memory, type of disk drives and video displays,
etc. CMOS requires very little power. When the computer is turned off, a backup battery provides power to the BIOS Flash chip, enabling it to retain the system
parameters. Each time the computer is powered-on, the computer is then configured with the values stored in the BIOS ROM by the system BIOS, which gains
control when the computer is powered on.
How To Change the Configuration Data
The CMOS information that determines the system parameters may be changed
by entering the BIOS Setup utility. This Setup utility can be accessed by pressing <Del> at the appropriate time during system boot.
Starting the Setup Utility
Normally, the only visible POST (Power On Self Test) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu
of the BIOS Setup utility. From the main menu, you can access the other setup
screens, such as the Chipset and Power menus. Section 4-3 gives detailed
descriptions of each parameter setting in the Setup utility.
7-1
SUPERWORKSTATION 5033C-T User's Manual
7-2
Running Setup
*Optimal default settings are in bold text unless otherwise noted.
The BIOS setup options described in this section are selected by choosing the
appropriate text from the Main BIOS Setup screen. All displayed text is described in this section, although the screen display is often all you need to
understand how to set the options (see on next page).
When you first power on the computer, the AwardBIOS™ is immediately activated.
While the BIOS is in control, the Setup program can be activated in one of two ways:
1.
By pressing <Del> immediately after turning the system on, or
2.
When the following message appears briefly at the bottom of the screen
during the POST (Power On Self-Test), press the <Del> key to activate
the Main Setup Menu.
Press DEL to enter SETUP
7-3
Main BIOS Setup
All Main Setup options are described in this section. The Main BIOS
Setup screen is displayed below.
Use the <Up> <Down> arrow keys or the <Tab> key to move among the different
settings in the above menu.
Press the <Esc> key to exit the CMOS Setup Menu and use the <Left> <Right>
arrow keys to enter the other categories of BIOS settings. The next section is
described in detail to illustrate how to navigate through the menus.
Main BIOS Setup Menu
7-2
Chapter 7: BIOS
Date/Time
Set the system date and time. Key in the correct information in the "mm",
"dd" and "yy" fields. Press the "Enter" key to save the data.
Legacy Diskette A
This setting allows the user to set the type of floppy disk drive installed as
diskette A. The options are "None", "360Kb, 5.25 in", "1.2MB, 5.25 in",
"720Kb, 3.5 in", "1.44 MB, 3.5 in", and "2.88MB 3.5 in".
Legacy Diskette B
This setting allows the user to set the type of floppy disk drive installed as
diskette B. The options are "None", "360Kb, 5.25 in", "1.2MB, 5.25 in",
"720Kb, 3.5 in", "1.44 MB, 3.5 in", and "2.88MB 3.5 in".
! IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, IDE
Channel 2 Master, IDE Channel 3 Master
These settings allow the user to set the parameters of the IDE Channel 0
Master/Slave, IDE Channel 1 Master/Slave, IDE Channel 1 Master/Slave, IDE
Channel 2 Master, IDE Channel 3 Master slots. Hit <Enter> to activate the
sub-menu screen for detailed options of these items. Set the correct
configurations accordingly.
IDE HDD Auto-Detection
This option allows the user to determine the manner in which the
AwardBIOS sets the settings for the IDE Primary Master Device. The
options are "None", "Auto" and "Manual."
IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, IDE
Channel 2 Master, IDE Channel 3 Master
Press the <Auto> key to activate the function of 'IDE HDD Auto-Detection",
which will allow the BIOS to automatically detect the status of the IDE
HDD installed in the system, such as the size, the number of cylinders,
the configurations of items such as Head, Precomp, Landing Zone and
Sector. The options are "None", "Auto", and "Manual."
Access Mode
This item determines the location through which the AwardBIOS
accesses the IDE Primary Master Device. The settings are "CHS", "LBA",
"Large", and "Auto".
Base Memory/Extended Memory/Total Memory
These are displays that inform you how much of each type of memory is
recognized as being present in the system.
7-3
SUPERWORKSTATION 5033C-T User's Manual
7-4 Advanced BIOS Setup
Choose Advanced BIOS Setup from the Award BIOS main menu with the Left/
Right arrow keys. You should see the following display. Select one of the
items in the left frame of the screen to go to the sub screen for that item.
Advanced BIOS Setup options are displayed by highlighting the option using
the arrow keys. All Advanced BIOS Setup options are described in this
section.
7-4.1
Advanced BIOS Features
When the item of Advanced BIOS Features is highlighted, press the <Enter>
key to activate the screen below:
Quick Boot
If enabled, this feature allows the system to skip certain tests while booting.
This will decrease the time needed to boot the system. The settings are
"Enabled" and "Disabled".
Quiet Boot
This feature allows the user to activate the function of "Quiet Boot". The
options are: "Enabled" and "Disabled".
7-4
Chapter 7: BIOS
ACPI Function
Select "Enabled" to activate the function of BIOS Support for Advanced
Configuration and Power Interface features. The settings are "Enabled" or
"Disabled".
ACPI Suspend Type
If enabled, the option allows the user to determine the ACPI Suspend type.
The options are "S1(POS)", "S3(STR)", and S1&S3.
APIC Mode
This setting allows you to Enable or Disable APIC. APIC is used to assign
interrupt signals to a specific processor on multi-processor system and
provides IRQs beyond the conventional 16 under Windows 2000 or XP. It
has no effect on single processor systems.
MPS Version Control
This setting allows you to state the MPS version for your operating system.
Options are "1.1" and "1.4".
PWRON After PWR-Fail
This setting allows the user to specify how the system will respond when
power is reapplied after the system has gone down due to a power failure.
The options are "Off", "On" and "Former-Sts (Former Status)".
7-4.2 Advanced Chipset Control
Access the submenu to make changes to the following settings.
7-5
SUPERWORKSTATION 5033C-T User's Manual
ECC Configuration
This setting allows you to enable or disable ECC (Error Correction and
Checking). The options are "ECC" and "Non-ECC".
CSA LAN (Giga-LAN)
Select "Enabled" to activate the function of CSA LAN. The options are
"Enabled" and "Disabled".
Smart Fan Control
Select "Enabled" to enable the function of Smart Fan Control. The options
are "Disabled" and "Enabled".
SATA Mode
This setting allows you to set the SATA Mode RAID via BIOS. The options
are "RAID" and "IDE".
On-Chip Serial ATA
This setting allows you to configure On-Chip Chipset Configurations. Select
"Disabled" to disable SATA controller. If "Auto" is selected, BIOS will
automatically configure the settings for SATA controller. Select "Combined
Mode" to combine the functionality of Parallel ATA (PATA) and Serial
ATA(SATA) (* with the maximum of two IDE drives available for each
channel.) If "Enhanced Mode" is selected, both SATA and PATA are
supported (*with the maximum of 6 IDE drives available.) If "SATA Only" is
selected, SATA will operate in the Legacy Mode. The options are Disabled,
Auto, Combined Mode, Enhanced Mode, and SATA only.
Serial ATA Port0/1 mode
This setting allows you to configure Serial ATA Port0/1 modes. The options
are Primary Master, Primary Slave, Secondary Master, Secondary Slave,
SATA0 Master and SATA1 Master.
USB Controller
This setting allows you to enable or disable the USB Controller. The options
are Enabled, and Disabled.
USB 2.0 Controller
This setting allows you to enable or disable USB 2.0 (EHCI) Controller. The
options are Enabled, and Disabled.
7-6
Chapter 7: BIOS
USB Legacy Support
This setting allows you to enable or disable the functions of USB, Keyboard/
Mouse under POST and DOS. The options are Disabled, and Enabled.
CPU THRM-Throttling
THRM throttling is used to lower power consumption and reduce the heat
generated by the CPU. The options for this setting are "87.5%", "75%",
"62.5%", "50%", "37.5%", "25%' and "12.5%".
7-4.3 I/O Device Configuration
Choose I/O Device Configuration from the Award BIOS main menu with the
Left/Right arrow keys. You should see the following display:
Keyboard Input Clock
This setting allows to you set the speed of the keyboard. The options are 6
MHz, 8 MHz, 12 MHz, and 16 MHz.
Onboard Serial Port1/Onboard Serial Port2
This setting allows the user to set the address and the corresponding IRQ
for the Serial Port1 and Serial Port 2. The options are "Disabled" , "3F8/
IRQ4", "2F8/IRQ3", "3E8/IRQ4", "2E8/IRQ3", and "Auto". The default setting
for Serial Port1 is "3F8/IRQ4" and the default for Port 2 is "2F8/IRQ3".
7-7
SUPERWORKSTATION 5033C-T User's Manual
UART Mode Select
This setting allows the user to select the UART mode for the BIOS. The
options are "IrDA", "ASKIR" and "Normal".
RxD, TxD Active
This allows the user to change the settings for the "RxD, TxD Active"
function. The options are "Hi, Hi", "Hi, Lo", "Lo, Hi", and "Lo, Lo".
IR Transmission Delay
If "Enabled", the transmission of IR (infrared) signals will be delayed. The
options are "Enabled" and "Disabled".
UR2 Duplex Mode
This setting set the mode for the UR2 Duplex Mode. The options are "Full"
and "Half".
Use IR Pins
This item sets the usage of the IR pins. The options are "RxD2, TxD2" and
"IR-Rx2Tx2".
Onboard Parallel Port
This setting allows the user to set the address and the corresponding IRQ
for the onboard parallel port. The options are "Disabled", "378/IRQ7", "278/
IRQ5" and "3BC/IRQ7".
Parallel Port Mode
This setting sets the mode for the onboard Parallel port. The options are
"SPP," "EPP", "ECP" "ECP+EPP" and "Normal".
EPP Mode Select
This setting allows the user to select the EPP port type. The options are
"EPP 1.9" and "EPP 1.7".
ECP Mode Use DMA
This setting allows the user to select the DMA channel for the ECP mode
(port) to use. The options are "1" and "3".
Watch Dog Timer Select
This setting allows you to select the setting for the Watch Dog Timer. The
Options are "Disabled", "10 Sec", "20 Sec", "30 Sec", "40 Sec", "I min", "2
min",and "4 min".
7-8
Chapter 7: BIOS
Power On Function
This setting allows the user to decide which method to use to power on the
system. The options are "Password", "Hot Key", "Mouse Left", "Mouse
Right", "Any Key", and "Button Only".
KB Power On Password
This setting allows the user to enter the Password when the system is
powered on via keyboard.
Hot Key Power On
This setting allows the user to decide which hot-keys to use in order to
power on the system. The options are "Ctrl-F1", "Ctrl-F2, Ctrl-F3", "CtrlF4", "Ctrl-F5", "Ctrl-F6", "Ctrl-F7", "Ctrl-F8", "Ctrl-F9", "Ctrl-F10", "Ctrl-F11"
and "Ctrl-F8".
7-4.4 PnP Configuration
Choose PCI/PnP Configurations from the Award BIOS main menu with the Left/
Right arrow keys. You should see the following display:
Reset Configuration Data
Enabling this setting resets the extended system configuration data when
you exit setup. Do this when you have installed a new add-on and the
system reconfiguration has caused such a serious conflict that the OS
cannot reboot the system. The options are "Enabled" and "Disabled".
7-9
SUPERWORKSTATION 5033C-T User's Manual
Resources Controlled By
This setting allows BIOS to automatically configure all boot and Plug and
Play compatible devices. If you choose Auto, you cannot select the IRQ,
DMA and memory base address fields because BIOS automatically assigns
them. The options are "Auto <ESCD>" and "Manual".
Onboard CSA LAN Boot
Select "Enabled" to enable the Boot ROM embedded in the Onboard CSA
LAN Chip. The options are: "Enabled" and "Disabled".
7-4.5 Console Redirection
Choose Console Redirection from the Award BIOS main menu with the Left/
Right arrow keys. You should see the following display:
Console Redirection
Select "Enabled" to redirect Console via COM Port. Select "Disabled" to
redirect Console when the keyboard is absent. The options are: "Enabled"
and "Disabled".
Agent Connect Via
This feature allows the user to set the connection mode for Console
Redirection. When "Null" is entered, Console Redirection will be set to
direct connection.
Agent Wait Time
This feature allows the user to set the timeout for the connection. The
options are "1 (Min)", "2 (Min)", "4 (Min)" and "8 (Min)".
7-10
Chapter 7: BIOS
Agent after Boot
Select "Disabled" to allows the Agent of Console Redirection to continue
running after OS bootup. The Options are "Enabled", and "Disabled".
7-4.6
Hardware Monitor
Choose Hardware Monitor from the Award BIOS main menu with the Left/Right
arrow keys. You should see the following display:
CPU Warning Temperature
This allows you to set the CPU warning temperature. If the CPU temperature
reaches this threshold, an alarm will activate and a warning message will
be displayed onscreen. The options are "Disabled", "60 0 C/140 0 F", "65 0 C/
149 0 F", "70 0 C/158 0 F", "75 0 C/167 0 F", "80 0 C/176 0 F" and "85 0 C/185 0 F".
7-11
SUPERWORKSTATION 5033C-T User's Manual
7-4.7 Processor & Clock Options
Limit CPUID MaxVal
This feature allows the user to set the limit for the CPUID Maximum Value.
The value can be set from 1 to 3. The options are "Enabled" and
"Disabled". (*For Windows XP, the option should be set to "Disabled.")
Hyper-Threading Technology
Select "Enabled" to activate the hyper-threading function of the CPUs to
make each CPU appear as if there were two CPUs to any programs that
support it (you must have OS support also). The settings are "Disabled"
and "Enabled."
CPU Clock Ratio
Key in a number between 8x to 50x to set the clock ratio of the processor.
The default setting is 8x. (*8x is only available for retail CPUs.)
Spread Spectrum
Spread Spectrum is a technique used to stablize a system by reducing the
level of ElectroMagnetic Interference. The options are "Enabled" and
"Disabled".
CPU Clock
Key in a number between 100 and 233 to set the CPU clock (MHz).
Supermicro does not recommend or make any guarantees with CPU
overclocking. The default setting is "200 MHz".
7-12
Chapter 7: BIOS
7-5
Security
Choose Security from the Award BIOS main menu with the Left/Right arrow
keys. You should see the following display:
Set Supervisor Password
When the item "Set Supervisor Password" is highlighted on the above
screen, press the <Enter> key. When prompted, type the Supervisor
Password in the dialogue box to set or to change the Supervisor
Password.
Set User Password
When the item "Set User Password" is highlighted on the above screen,
press the <Enter> key. When prompted, type the User Password in the
dialogue box to set or to change the User Password.
Password Check
This setting allows the user to determine if the password is required every
time when the system boots up or if the password is required only when
you enter the CMOS setup. The options are "System" and "Setup".
7-13
SUPERWORKSTATION 5033C-T User's Manual
7-6
Boot
Choose Boot from the Award BIOS main menu with the Left/Right arrow keys.
You should see the following display:
! Removable Device Priority
This setting allows you to set the priority of removable devices. The options
are "Floppy Disks", "LS120", "Zip 100", "USB-FDD0", "USB-FDD1", "USBZIP0", and "USB-ZIP1".
! CD ROM Drives Boot Priority
This item allows the user to specify the boot sequence of the available CD
ROM Devices.
! Hard Disk Boot Priority
This item allows the user to select the Boot Priority of the following Hard
Disk Devices.
First Boot Device
This item allows the user to set the first boot-up device. The options are
"Removable", "Hard Disks", "CDROM", "Legacy LAN", and "Disabled".
7-14
Chapter 7: BIOS
Second Boot Device
This item allows the user to set the second boot-up device. The options
are "Removable", "Hard Disks", "CDROM", "Legacy LAN", and "Disabled".
Third Boot Device
This item allows the user to set the Third boot-up device. The options are
"Removable", "Hard Disks", "CDROM", "Legacy LAN", and "Disabled".
Boot Other Device
If enabled, this option enables the BIOS to load the OS from another device
rather than the ones that have been specified as the first, second and third
boot up devices. The settings are "Enabled" and "Disabled".
7-7
Exit
Choose Exit from the Award BIOS main menu with the Left/Right arrow keys.
You should see the following display:
Save & Exit Setup
When the item "Save & Exit Setup" is highlighted, press <Enter> to save the
changes you've made in the BIOS program (CMOS) and exit. Your system
should, then, continue with the boot-up procedure.
Exit without Saving
When the item "Exit without Saving" is highlighted, press <Enter> to exit the
Setup routine without saving any changes you may have made. Your system should then continue with the boot-up procedure.
7-15
SUPERWORKSTATION 5033C-T User's Manual
Load Fail-Safe Defaults
Highlight this item and hit <Enter> to load the default settings for all items in
the BIOS Setup. These are the safest settings to use.
Load Optimized Defaults
Highlight this item and hit <Enter> to load the optimized settings for all items
in the BIOS Setup. These settings provide you with optimal system
performance.
Discard Changes
When the item "Discard Changes" is highlighted, press <Enter> to discard
any changes you made to the BIOS settings and to stay in BIOS Setup.
Your system should then continue with the boot-up procedure.
7-16
Appendix A: BIOS POST Messages
Appendix A
BIOS POST Messages
During the Power-On Self-Test (POST), the BIOS will check for problems. If a problem
is found, the BIOS will activate an alarm or display a message. The following is a list
of such BIOS messages.
Beeps
1 long beep
1 long beep+2 short beeps
Error Message
Memory Modules Errors
VGA Errors
A-1
SUPERWORKSTATION 5033C-T User's Manual
Notes
A-2
Appendix B: BIOS POST Codes
Appendix B
BIOS POST Codes
This section lists the POST (Power On Self Testing) Codes for the Award BIOS.
POST (hex)
CFh
C0h
C1h
C3h
C5h
0h1
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
Description
Test CMOS R/W functionality.
Early chipset initialization:
-Disable shadow RAM
-Disable L2 cache (socket 7 or below)
-Program basic chipset registers
Detect memory
-Auto-detection of DRAM size, type and ECC.
-Auto-detection of L2 cache (socket 7 or below)
Expand compressed BIOS code to DRAM
Call chipset hook to copy BIOS back to E000 & F000 shadow
RAM.
Expand the Xgroup codes locating in physical address 1000:0
Reserved
Initial Superio_Early_Init switch.
Reserved
1. Blank out screen
2. Clear CMOS error flag
Reserved
1. Clear 8042 interface
2. Initialize 8042 self-test
1. Test special keyboard controller for Winbond 977 series Super
I/O chips.
2. Enable keyboard interface.
Reserved
! Disable PS/2 mouse interface (optional).
! Auto detect ports for keyboard & mouse followed by a port & interface swap
(optional).
! Reset keyboard for Winbond 977 series Super I/O chips.
Reserved
Reserved
Reserved
Test F000h segment shadow to see whether it is R/W-able or not. If
test fails, keep beeping the speaker.
B-1
SUPERWORKSTATION 5033C-T User's Manual
POST (hex)
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
20h
21h
22h
23h
24h
25h
26h
27h
28h
29h
2Ah
2Bh
2Ch
Description
Reserved
Auto detect flash type to load appropriate flash R/W codes into the
run time area in F000 for ESCD & DMI support.
Reserved
Use walking 1’s algorithm to check out interface in CMOS
circuitry. Also set real-time clock power status, and then check for
override.
Reserved
Program chipset default values into chipset. Chipset default
values are MODBINable by OEM customers.
Reserved
Initial Early_Init_Onboard_Generator switch.
Reserved
Detect CPU information including brand, SMI type (Cyrix or
Intel) and CPU level (586 or 686).
Reserved
Reserved
Initial interrupts vector table. If no special specified, all H/W
interrupts are directed to SPURIOUS_INT_HDLR & S/W
interrupts to SPURIOUS_soft_HDLR.
Reserved
Initial EARLY_PM_INIT switch.
Reserved
Load keyboard matrix (notebook platform)
Reserved
HPM initialization (notebook platform)
Reserved
1. Check validity of RTC value:
e.g. a value of 5Ah is an invalid value for RTC minute.
2. Load CMOS settings into BIOS stack. If CMOS checksum fails, use default
value instead.
3. Prepare BIOS resource map for PCI & PnP use. If ESCD is valid, take into
consideration of the ESCD’s legacy information.
4. Onboard clock generator initialization. Disable respective clock resource to
empty PCI & DIMM slots.
5. Early PCI initialization:
-Enumerate PCI bus number
-Assign memory & I/O resource
-Search for a valid VGA device & VGA BIOS, and put it
into C000:0.
Reserved
Reserved
Reserved
Initialize INT 09 buffer
Reserved
! Program CPU internal MTRR (P6 & PII) for 0-640K memory address.
! Initialize the APIC for Pentium class CPU.
! Program early chipset according to CMOS setup. Example: onboard IDE
controller.
! Measure CPU speed.
! Invoke video BIOS.
Reserved
Reserved
Reserved
B-2
Appendix B: BIOS POST Codes
POST (hex)
2Dh
2Eh
2Fh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
3Bh
3Ch
3Dh
3Eh
3Fh
40h
41h
42h
43h
44h
45h
46h
47h
48h
49h
4Ah
4Bh
4Ch
4Dh
4Eh
4Fh
50h
51h
52h
53h
54h
55h
56h
57h
Description
1. Initialize multi-language
2. Put information on screen display, including Award title, CPU type, CPU
speed ….
Reserved
Reserved
Reserved
Reserved
Reserved
Reset keyboard except Winbond 977 series Super I/O chips.
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Test 8254
Reserved
Test 8259 interrupt mask bits for channel 1.
Reserved
Test 8259 interrupt mask bits for channel 2.
Reserved
Reserved
Test 8259 functionality.
Reserved
Reserved
Reserved
Initialize EISA slot
Reserved
1. Calculate total memory by testing the last double word of each 64K page.
2. Program writes allocation for AMD K5 CPU.
Reserved
Reserved
Reserved
Reserved
1. Program MTRR of M1 CPU
2. Initialize L2 cache for P6 class CPU & program CPU with proper cacheable
range.
3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller one in case the
cacheable ranges between each CPU are not identical.
Reserved
Initialize USB
Reserved
Test all memory (clear all extended memory to 0)
Reserved
Reserved
Display number of processors (multi-processor platform)
Reserved
1. Display PnP logo
2. Early ISA PnP initialization
-Assign CSN to every ISA PnP device.
B-3
SUPERWORKSTATION 5033C-T User's Manual
POST (hex)
58h
59h
5Ah
5Bh
5Ch
5Dh
5Eh
5Fh
60h
61h
62h
63h
64h
65h
66h
67h
68h
69h
6Ah
6Bh
6Ch
6Dh
6Eh
6Fh
70h
71h
72h
73h
74h
75h
76h
77h
78h
79h
7Ah
7Bh
7Ch
7Dh
7Eh
7Fh
Description
Reserved
Initialize the combined Trend Anti-Virus code.
Reserved
(Optional Feature)
Show message for entering AWDFLASH.EXE from FDD (optional)
Reserved
1. Initialize Init_Onboard_Super_IO switch.
2. Initialize Init_Onboard_AUDIO switch.
Reserved
Reserved
Okay to enter Setup utility; i.e. not until this POST stage can users
enter the CMOS setup utility.
Reserved
Reserved
Reserved
Reserved
Initialize PS/2 Mouse
Reserved
Prepare memory size information for function call:
INT 15h ax=E820h
Reserved
Turn on L2 cache
Reserved
Program chipset registers according to items described in Setup &
Auto-configuration table.
Reserved
1. Assign resources to all ISA PnP devices.
2. Auto assign ports to onboard COM ports if the corresponding item in Setup is
set to “AUTO”.
Reserved
1. Initialize floppy controller
2. Set up floppy related fields in 40:hardware.
Reserved
Reserved
Reserved
(Optional Feature)
Enter AWDFLASH.EXE if :
-AWDFLASH is found in floppy drive.
-ALT+F2 is pressed
Reserved
Detect & install all IDE devices: HDD, LS120, ZIP, CDROM…..
Reserved
Detect serial ports & parallel ports.
Reserved
Reserved
Detect & install co-processor
Reserved
Reserved
Reserved
Reserved
1. Switch back to text mode if full screen logo is supported.
-If errors occur, report errors & wait for keys
-If no errors occur or F1 key is pressed to continue:
#Clear EPA or customization logo.
B-4
Appendix B: BIOS POST Codes
POST (hex)
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
90h
91h
92h
93h
94h
95h
96h
FFh
Description
Reserved
Reserved
1. Call chipset power management hook.
2. Recover the text font used by EPA logo (not for full screen logo)
3. If password is set, ask for password.
Save all data in stack back to CMOS
Initialize ISA PnP boot devices
1. USB final Initialization
2. NET PC: Build SYSID structure
3. Switch screen back to text mode
4. Set up ACPI table at top of memory.
5. Invoke ISA adapter ROMs
6. Assign IRQs to PCI devices
7. Initialize APM
8. Clear noise of IRQs.
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Read HDD boot sector information for Trend Anti-Virus code
1. Enable L2 cache
2. Program boot up speed
3. Chipset final initialization.
4. Power management final initialization
5. Clear screen & display summary table
6. Program K6 write allocation
7. Program P6 class write combining
1. Program daylight saving
2. Update keyboard LED & typematic rate
1. Build MP table
2. Build & update ESCD
3. Set CMOS century to 20h or 19h
4. Load CMOS time into DOS timer tick
5. Build MSIRQ routing table.
Boot attempt (INT 19h)
B-5
SUPERWORKSTATION 5033C-T User's Manual
Notes
B-6
Appendix C: Software Installation
Appendix C
Software Installation
After all the hardware has been installed, you must first configure the Adaptec
Embedded Serial ATA RAID driver before you install the operating system. The
necessary drivers are all included on the Supermicro bootable CDs that came
packaged with your motherboard.
C-1 Introduction to Serial ATA
Serial ATA (SATA)
Serial ATA (SATA) is a physical storage interface. It uses a single cable with a
minimum of four wires to create a point-to-point connection between devices. It is a
serial link which supports transfer rates from 150 MB/s. Because the serial cables
used in SATA are thinner than the traditional cables used in Parallel ATA (PATA),
SATA systems can be installed in smaller chassis than PATA. In addition, PATA
cables can only extend to 40cm, while SATA cables can extend up to one meter.
Overall, SATA provides better functionality than PATA.
Intel 6300ESB I/O Controller Hub
Located in the South Bridge of Intel's 875 chipset, the 6300ESB I/O Controller Hub
provides the I/O subsystem with access to the rest of the system. In addition to
supporting a dual-channel Ultra ATA/100 Bus Master IDE controller (PATA), the
6300ESB also supports two SATA host controllers, which provides support for up to
two SATA ports and up to two RAID drives. The 6300ESB supports the PATA and
SATA device configurations listed below.
ATA Operating Modes
You can select from the following two modes: Combined Mode and Enhanced Mode.
Combined Mode
In this mode, system BIOS assigns the traditional IRQ 14 and IRQ 15 for HDD use.
Up to four ATA devices are supported by this mode.
Within the Combined Mode, the following three modes are supported:
Non-Combined Mode: Parallel ATA only, with a maximum of four devices supported.
C-1
SUPERWORKSTATION 5033C-T User's Manual
Non-Combined Mode: SATA only, with a maximum of two devices supported.
Combined Mode: SATA and PATA devices, with support for two devices of each for
a total of four devices maximum. For IDE(PATA)/SATA configurations, please refer
to the table below.
Primary Master(=PM)
Yes Yes No
No
No
No
Primary Slave(=PS)
Yes No
Yes No
No
No
Secondary Master(=SM) Yes No
No
Yes No
No
Secondary Slave(=SS)
Yes No
No
No
Yes No
SATA Port0
No
SM
SM
PM
PM
PM
SATA Port1
No
SS
SS
PS
PS
PS
*Note: (No=Not Present, Yes=Present) Also, if Logical Primary is
selected, the IDE channels are no longer available.
Enhanced Mode
In this mode, system BIOS will automatically search for all available IRQs for HDD
use. For newer operating systems that support Enhanced Mode (such as
WindowsXP, Windows2000 and Windows2003), you can set SATA and PATA to the
Enhanced Mode. (These newer operating systems can accommodate both Enhanced and Combined Modes and support up to six ATA devices.)
Please refer to "Advanced Chipset Control" under the "Advanced" setup section in
BIOS to select Combined Mode or Enhanced Mode.
C-2
Appendix C: Software Installation
C-2 Intel Hance Rapids Driver Installation
a. Insert Supermicro's bootable CD that came with the system into the CD drive
and restart the system. Upon reboot, a screen entitled "Super Micro Driver
Diskette Maker" will appear.
b. Choose from the list the item: "Intel Hance Rapids Driver by 3rd Party
(Adaptec)" and press <Enter>.
c. On the next screen displayed, choose the OS driver you want to install and
press <Enter>.
d. Insert a formatted diskette into floppy (A drive) and press <Enter> as prompted.
e. Exit the program after the process is completed. Then, reboot the system.
f. Insert a Microsoft Windows OS Setup CD in the CD Driver, and the system will
start to boot up from the CD.
g. Press the <F6> key when the message-"Press F6 if you need to install a third
party SCSI or RAID driver" displays.
h. When the Windows OS Setup screen appears, press "S" to specify additional
device(s).
i. Insert the driver diskette named "Adaptec Embedded Serial ATA Raid Controller Driver" into drive A: and press the <Enter> key.
j. Choose Adaptec Embedded Host Serial ATA Raid Controller from the list
indicated in the Windows OS Setup Screen, and press the <Enter> key.
k. Press the <Enter> key to continue the installation process. (If you need to
specify any additional devices to be installed, do so at this time.) Once all
devices are specified, press the <Enter> key to continue with the installation.
l. From the Windows OS Setup screen, press the <Enter> key. The OS Setup
will automatically load all device files and then continue the Windows OS installation.
m. After the Windows OS Installation is completed, the system will automatically
reboot.
C-3
SUPERWORKSTATION 5033C-T User's Manual
C-3 Other Software Programs and Drivers
After you've installed Windows Operating System, the screen shown below will
appear. You are now ready to install the additional software programs and
drivers included on the CD. To install these software programs and drivers, click
the icons to the right of these items.
Figure C-1. Driver/Tool Installation Screen
You may also click the icons showing a hand writing on paper to view the readme
files for each item. Click the computer icons to the right of these items to install
each item (from top to the bottom) one at a time. After installing each item,
you must re-boot the system before moving on to the next item on the list.
You should install everything here except for the SUPER Doctor utility, which is
optional. The bottom icon with a CD on it allows you to view the entire contents
of the CD.
C-4
Appendix C: Software Installation
Supero Doctor III
The Supero Doctor III program is a Web base management tool that supports
remote management capability. It includes Remote and Local Management
tools. The local management is called SD III Client. The Supero Doctor III
program included on the CDROM that came with your motherboard allows you
to monitor the environment and operations of your system. Supero Doctor III
displays crucial system information such as CPU temperature, system
voltages and fan status. See the Figure below for a display of the Supero
Doctor III interface.
Figure C-2. Supero Doctor III Interface Display (Health Information)
Note: For Linux, we recommend using Supero Doctor II.
C-5
SUPERWORKSTATION 5033C-T User's Manual
Notes
C-6
Appendix D: System Specifications
Appendix D
System Specifications
Processors
Single Intel® Pentium® 4 processors of up to 3.40 GHz with HT
technology or single Intel® Celeron® processors of up to 2.80 GHz at a
800/533/400 MHz front side bus speed
Chipset
Intel 875P
Memory Capacity
Four (4) DIMM slots to support a maximum of 4 GB unbuffered ECC or
non-ECC DDR400/333/266 SDRAM (with a dual-channel memory bus)
DIMM Sizes
128 MB / 256 MB / 512 MB / 1 GB 184-pin modules supported
Serial ATA Controller
6300ESB controller hub incorporated into chipset
Serial ATA Backplane (non-SAF-TE)
SATA backplane (CSE-SATA-733) for four (4) SATA drives
Main Drive Bays
Four (4) 1" drive bays to house four (4) standard hot-swap SATA drives
Peripheral Bays
One (1) full-height 3.5" drive bay
Two (2) full-height 5.25" drive bays
PCI/Peripheral Card Expansion Slots
Three (3) 64-bit 66 MHz (3.3V) PCI-X slots
Two (2) 32-bit 33 MHz (5V) PCI slots
One (1) 8xAGP Slot (1.5V, backward compatible with 4xAGP and 2xAGP)
Motherboard
Model: P4SCT+II (ATX Form Factor)
Dimensions: 12 x 9.5 in (305 x 241 mm)
D-1
SUPERWORKSTATION 5033C-T User's Manual
Chassis
Model: SC733T-350 (mid-tower)
Dimensions: (HxWxD) 16.7 x 7 x 22 in. (424 x 178 x 559 mm)
Weight
Gross Weight: 40 lbs. (18.2 kg.)
System Cooling
One (1) 12-cm thernal exhaust fan (FAN-0055)
One (1) 9-cm thermal cooling fan (FAN-0060)
System Input Requirements
AC Input Voltage: 100-240 VAC
Rated Input Current: 6A (115V) to 3A (230V)
Rated Input Frequency: 50 to 60 Hz
Power Supply
Rated Output Power: 350W (Model# SP352-PS, Part# PWS-0059)
Rated Output Voltages: +3.3V (20A), +5V (25A), +12V (24A), -12V (0.5A),
+5Vsb (2A)
BTU Rating
1860 BTUs/hr (for a rated output power of 350W)
Operating Environment
Operating Temperature: 10º to 35º C (50º to 90º F)
Non-operating Temperature: -40º to 70º C (-40º to 158º F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory Compliance
Electromagnetic Emissions:
FCC Class B, EN 55022 Class B, EN 61000-3-2/-3-3, CISPR 22 Class B
Electromagnetic Immunity:
EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11)
Safety:
EN 60950/IEC 60950-Compliant, UL Listed (USA), CUL Listed (Canada),
TUV Certified (Germany), CE Marking (Europe)
D-2