Website: http: //www.LGEservice.com
E-mail: http: //www.LGEservice.com/techsup.html
WASHING MACHINE
SERVICE MANUAL
!
CAUTION
READ THIS MANUAL CAREFULLY TO DIAGNOSE
PROBLEMS CORRECTLY BEFORE SERVICING THE UNIT.
MODEL: WM2688H*MA
100
SEP. 2007 PRINTED IN KOREA
P/No.:MFL30599112
101
CONTENTS
1. SPECIFICATIONS ............................................................................................................... 3
2. FEATURES & TECHNICAL EXPLANATION ....................................................................... 4
3. PARTS IDENTIFICATION ................................................................................................... 7
4. INSTALLATION & TEST ...................................................................................................... 8
5. OPERATION ...................................................................................................................... 11
6. WIRING DIAGRAM/PROGRAM CHART .......................................................................... 14
7. TROUBLESHOOTING ...................................................................................................... 16
7-1. BEFORE PERFORMING SERVICE .......................................................................... 16
7-2. QC TEST MODE ........................................................................................................ 16
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY ..............................................16
7-4. ERROR DISPLAY ...................................................................................................... 17
8. ERROR DIAGNOSIS AND CHECK LIST .......................................................................... 19
8-1. DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERATION ............................... 19
8-2. FAULT DIAGNOSIS AND TROUBLESHOOTING ..................................................... 22
9. DISASSEMBLY INSTRUCTIONS ..................................................................................... 30
10. EXPLODED VIEW .......................................................................................................... 41
10-1. CABINET & CONTROL PANEL ASSEMBLY .......................................................... 41
10-2. DRUM & TUB ASSEMBLY ..................................................................................... 42
10-3. DISPENSER ASSEMBLY ....................................................................................... 43
2
1. SPECIFICATIONS
ITEM
WM2688H*M
COLOR
W:BLUE WHITE, N:NAVY BLUE
POWER SUPPLY
AC 120 V, 60 Hz
PRODUCT WEIGHT
192 lbs (87kg)
ELECTRIC POWER
WASHING
280 W
DRAIN MOTOR
80 W
WASH HEATER
1000 W
WASH
46 rpm
SPIN
0-1320 rpm
CONSUMTION
REVOLUTION SPEED
CYCLES
9
WASH/RINSE TEMPERATURES
5
SPIN SPEEDS
5
OPTIONS
Prewash, Rinse+Spin, Extra Rinse, Water Plus, Stain Cycle
WATER CIRCULATION
Incorporated
14.5-116 psi (100-800 kPa)
OPERATIONAL WATER PRESSURE
CONTROL TYPE
Electronic
WASH CAPACITY [cu.ft]
3.47 (4.0 IEC)
DIMENSIONS
27” (W) X 29 3/4” (D) X 3811/16” (H), 5013/16” (D, door open)
DELAY WASH
up to 19 hours
DOOR SWITCH TYPE
PTC + Solenoid
WATER LEVEL
10 steps (by sensor)
LAUNDRY LOAD SENSING
Incorporated
ERROR DIAGNOSIS
Incorporated
AUTO POWER OFF
Incorporated
CHILD LOCK
Incorporated
RLM ENABLE
Incorporated
STEAM
Incorporated
3
2. FEATURES & TECHNICAL EXPLANATION
2-1. FEATURES
■
Ultra Capacity
The Larger drum enables not just higher head drop and stronger centrifugal force, but
also less tangling and wrinkling of the laundry. Heavier loads, such as king size
comforters, blankets, and curtains, can be washed.
추가선택, 예약,
■
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
■
Tilted Drum and Extra Large Door Opening
Tilted drum and extra large opening make it possible to load
and unload clothing more easily.
■
Steam Washing and SteamFreshTM
Steam Washing features upgraded washing performance with low energy and water
consumption. SteamFreshTM cycle removes wrinkles from dry clothes.
■
RollerJets
Washing ball enhances the wash performance and reduces damage
to the clothing. The jets spray and help tumble clothes to enhance
washing performance while maintaining fabric care.
■
Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
■
Built-in Heater
Internal heater helps to maintain water temperature at its optimum level for selected
cycles.
추가선택, 예약,
■
Child Lock
The Child lock prevents children from pressing any button to change the settings
during operation.
■
Using the RLM (Remote Laundry Monitor)
The RLM monitors status of your washer and/or dryer. You can plug the display unit
into any power outlet in your home.
The RLM Display Unit can be purchased separately for this washer.
4
2-2. NEURO FUZZY WASHING TIME OPTIMIZATION
To get the best washing performance, optimal time is determined by the water temperature,
the selected washing temperature, and the size of the load.
water
temperature
washing time
selected
washing
temperature
NEUROFUZZY
the best
washing
performance
rinsing time
spin rhythm, time
load
size
SENSING
PROCESSING
DETERMINATION
EFFECT
2-3. WATER LEVEL CONTROL
● This model incorporates a pressure sensor which can sense the water level in the tub.
● The water supply is stopped when the water level reaches the preset level, the washing
program then proceeds.
● Spinning does not proceed until the water in the tub drains to a certain level.
2-4. DOOR CONTROL
● The door can be opened by pulling the door handle whenever washer is not in operation.
● When the cycle is completed, the DOOR LOCKED light will turn off.
● If a power failure has occurred while in operation, the door will unlock after 5 minutes.
● Clicking sounds can be heard when the door is locked/unlocked.
5
2-5. THE DOOR CAN NOT BE OPENED
● While program is operating
● When a power failed and power plug is taken out in operation
● While Door Lock lights turn on.
● White the motor is in the process of intertial rotating, through the operation is paused.
2-6. DOOR LOCKED LAMP LIGHTS
● When the frequency of water level is lower than 22.9 kHz
(It can be canceled when the frequency is more than 23.8 kHz)
● When the temperature inside the tub is higher than 45 °C and water level is not 25.5 kHz
(It can be canceled when the water level is 25.5 kHz or the temperature inside the tub is lower than 40 °C)
2-7. CHILD LOCK
● Use this option to prevent unwanted use of the washer. Press and hold PRE WASH button for 3 seconds to
lock/unlock control.
● When Child lock is set, CHILD LOCK lights and all buttons are disabled except the Power
button. You can
lock the washer while it is operating.
2-8. WATER CIRCULATION
● When Washing and Rinsing function of shower at the upper part of Gasket.
● When Washing, it continuously operates for 3 minutes and intermittently.
● When Rinsing, it continuously operates after completion of water supply.
2-9. STEAM
● For tough stained clothes, underwear, or baby clothes.
● Steam Wash is available with Sanitary, Bulk/Large, Perm. Press, Cotton/Normal, and baby Wear cycles.
● This option features upgraded washing performance with low energy and water consumption
● Do not load delicates such as wool, silk, and easily discolored clothes.
2-10. DRUM LIGHT
● The Drum Light comes on when the Power button is pressed. It goes off when the door is closed and the
washer starts operation.
● The Drum Light remains off when the door is locked.
● The Drum Light can be turned on while the washer is in operation by pressing the Rinse+Spin button for 3
seconds. The light will turn off automatically 4 minutes later.
● The Drum Light comes on when the washing cycle is finished and goes off 4 minutes later.
6
3. PARTS IDENTIFICATION
STEAM
DOOR LOCK
CHILD LOCK
EST. TIME:
REMANING
DELAY WASH
1:21
5%
WASHING
HIGH
NORMAL
HIGH
HOT/
COLD
& Steam Nozzle
Drum Light
Door Seal
Safety Cover (PLC Modem)
Included Accessories
Hot and Cold
Water Hoses
Caps (4)
(for covering
shipping bolt holes)
Wrench
(for removing
shipping bolts and
adjusting leveling feet)
7
Tie Strap
(for securing
drain hose)
Elbow Bracket
(for securing
drain hose)
4. INSTALLATION & TEST
1⃞ Before servicing, ask the customer what the trouble is.
2⃞ Check the setup (power supply is 120 V AC, remove the transit bolts....).
3⃞ Check with the troubleshooting guide.
4⃞ Plan your service method by referring to the disassembly instructions.
5⃞ Service the unit.
6⃞ After servicing, operate the appliance to see whether it functions correctly.
■ STANDARD INSTALLATION
The appliance should be installed as follows:
REMOVE THE SHIPPING
INSTALL THE APPLIANCE
ADJUST THE
BOLTS
ON A FLAT AND FIRM SURFACE
LEVELING
Remove the 4 shipping bolts
with the supplied wrench.
Turn the leveling feet to adjust
the appliance.
※ Do first lower side to remove easily.
Keep the shipping bolts and
spanner for future use.
Insert the 4 caps
(provided) into the hole.
Turn clockwise to raise;
counterclockwise to lower.
8
■ HOW TO CONNECT THE INLET HOSE
Verify that the rubber washer is inside of the
valve connector.
Tighten the inlet hose securely to prevent leaks.
■ CONNECT THE DRAIN HOSE
· Make sure that the hose is not twisted.
· Avoid submerging the end of the hose.
※ The end of the drain hose should be placed less than 96” from the floor.
■ CONNECT POWER PLUG
· Avoid connecting several electric devices, as
doing so may cause a fire.
· Connect the power plug to the wall outlet.
9
TEST OPERATION
Preparation for
washing.
Press the POWER button.
STEAM
5%
DOOR LOCK
CHILD LOCK
WASHING
HOT/
COLD
HIGH
EST. TIME:
REMANING
NORMAL
Press the Start/Pause
button.
DELAY WASH
1:21
HIGH
Connect the power plug to
the outlet.
Connect the inlet hoses.
Check the water heating
function.
Listen for a click to determine if
the door has locked.
Check the automatic
reverse rotation.
Check the water supply.
MAX
STEAM
5%
DOOR LOCK
CHILD LOCK
WASHING
HOT/
COLD
EST. TIME:
REMANING
DELAY WASH
1:21
STEAM
5%
DOOR LOCK
CHILD LOCK
WASHING
HIGH
NORMAL
HIGH
Press the WASH/RINSE button
and the present temperature will
be displayed.
Check the drain and spin
functions.
HOT/
COLD
HIGH
EST. TIME:
REMANING
NORMAL
DELAY WASH
1:21
SOFTENER
HIGH
Check if the drum rotates
clockwise and counterclockwise.
Press the
START/PAUSE button.
Check if water is supplied
through the detergent dispenser.
Water removal
Power off and the power on.
Press the SPIN SPEED button.
Press the START/PAUSE button.
Check the spin and drain
functions.
Listen for a click to determine
if the door is unlocking.
10
If SVC is needed during check,
remove the remaining water by
pulling out the hose cap.
5. OPERATION
■ WM2688H*MA
11
Power Button
• Use this button to turn the power
On/Off.
Status Indicator
• It shows elapsed time of the cycle the washer is
operating.
Start/Pause
Cycle Selector Knob
• Rotate the Cycle selector knob to select the cycle designed for
different types of fabric and soil levels.
12
• Use this button to Start/
Stop the washer.
Option Button
• PREWASH: Use this option for loads that need pretreatment. It adds 16 minutes prewash and a spin cycle.
• RINSE+SPIN: Use this option to rinse and then spin.
• EXTRA RINSE: This option provides an additional rinse.
• STAIN CYCLE: Adds time to the wash and rinse cycles for better stain removal. Automatically provides a rinse.
• WATER PLUS: Add extra water to the wash and rinse cycles for superior results.
Wash/Rinse, Spin speed, Soil Level, Beeper Button
• Select a water temperature based on the type of load you are washing.
• To change the spin speed, press the Spin Speed button repeatedly to cycle through available options.
• To change the soil level, press the Soil Level button repeatedly until the desired setting is on.
• Press repeatedly to adjust the volume of the Beeper
13
6. WIRING DIAGRAM/PROGRAM CHART
14
15
7. TROUBLESHOOTING
7-1. BEFORE PERFORMING SERVICE
■ Be careful of electric shock when disconnecting parts while troubleshooting.
■ The voltage of each terminal is 120 V AC and DC when the unit is plugged in.
7-2. QC TEST MODE.
The washer must be empty and the controls must be in the off state.
1. Press the SPIN SPEED and SOIL LEVEL buttons simultaneously.
2. Press the Power
button, while the above condition. Then buzzer will sound twice.
3. Press the Start/Pause
button repeatedly to cycle through the test modes.
Number of times the
Start/Pause button is pressed
Check Point
Display Status
QC TEST MODE
None
Turns on all lamps and locks the door.
1 time
Tumble clockwise.
rpm (42~50)
2 times
Low speed Spin.
rpm (55~65)
3 times
High speed Spin.
rpm (125~135)
4 times
Inlet valve for prewash turns on.
Water level frequency (25~65)
5 times
Inlet valve for main wash turns on.
Water level frequency (25~65)
6 times
Inlet valve for hot water turns on.
Water level frequency (25~65)
7 times
Inlet valve for steam turns on.
Water level frequency (25~65)
8 times
Inlet valve for bleach turns on.
Water level frequency (25~65)
9 times
Tumble counterclockwise.
rpm (42~50)
10 times
Heater turns on for 3 sec.
Water temperature
11 times
Circulation pump turns on.
Water level frequency (25~65)
12 times
Drain pump turns on.
Water level frequency (25~65)
13 times
Steam Heater turns on for 1.2 sec.
TSG temperature
14 times
Off
-
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY
Press the WASH/RINSE and SOIL LEVEL button simultaneously.
***
***
***
***
***
***
***
***
***
***
***
***
***
• The digits indicate the water level frequency.
So, for example a display indicating 058: a Water level frequency of 20+(58 x 0.1)
= 25.8 kHz
16
7-4. ERROR DISPLAY
If you press the START/PAUSE button when an error is displayed, any error exceptd
ewill
disappear and the machine will go into the pause status.
In case ofd
e
d
,
e
d
,
eif the error is not resolved within 20 sec., or the in case of other
errors, if the error is not resolved within 4 min., power will be turned off automatically and the error
code will blink. But in the case ofd
e
, power will not be turned off.
ERROR
SYMPTOM
CAUSE
• Correct water level (246) is not reached within 8 minutes
after water is supplied or it does not reach the preset water
level within 25 minutes.
1
WATER INLET
ERROR
2
IMBALANCE
ERROR
3
DRAIN
ERROR
4
OVER FLOW
ERROR
• Water is overflowing (water level frequency is over 213).
※ If
is displayed, the drain pump will operate to
drain the water automatically.
5
PRESSURE
SENSOR
ERROR
• The SENSOR SWITCH ASSEMBLY is out of order.
6
DOOR OPEN
ERROR
7
HEATING
ERROR
• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.
• Not fully drained within 10 minutes.
• Door not all the way closed.
• Loose electrical connections at Door switch and
PWB Assembly.
• The DOOR SWITCH ASSEMBLY is out of order.
• The THERMISTOR is out order.
17
ERROR
SYMPTOM
CAUSE
8
LOCKED
MOTOR
ERROR
• The connector (3-pin, male, white) in the MOTOR
HARNESS is not connected to the connector
(3-pin, female, white) of STATOR ASSEMBLY.
• The electric contact between the connectors
(3-pin, male, white) in the MOTOR HARNESS
and 4-pin, female, white connector in the MAIN PWB
ASSEMBLY is bad or unstable.
• The MOTOR HARNESS between the STATOR
ASSEMBLY and MAIN PWB ASSEMBLY is cut (open
circuited).
• The hall sensor is out of order/defective.
10
EEPROM
ERROR
EE
• EEPROM is out of order.
※ Displayed only when the START/PAUSE button is first
pressed in the QC Test Mode.
11
POWER
FAILURE
F
• The washer experienced a power failure.
18
8. ERROR DIAGNOSIS AND CHECK LIST
8-1. DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERATION
SYMPTOM
No power
GUIDE FOR SERVICE CALL
Is the power plug connected firmly to
120 V AC outlet?
YES
Power failure? or Breaker opened?
Is the outlet controlled by a switch?
NO
Visit to service.
Water inlet trouble
Is
displayed?
YES
Is the tap opened?
YES
Is the tap frozen?
NO
Is the water supply shut-off?
NO
Is filter in the inlet valve clogged with
foreign material?
NO
Visit to service.
19
YES
Clean the filter of
inlet valve
SYMPTOM
GUIDE FOR SERVICE CALL
Door error
Was the load too large?
Visit to service.
Drain trouble
Visit to service.
20
SYMPTOM
Suds overflow from the
appliance.
(In this condition, wash and
spin do not operate normally)
GUIDE FOR SERVICE CALL
Is a HE (High Efficiency) detergent used?
YES
Is the proper amount of detergent used
as recommended?
YES
Recommend to reduce the amount
of detergent.
This appliance has an automatic suds sensing function which
prevents overflow.
When excessive suds are sensed, the suds removing
implementations such as drain, water input, pause will operate,
without rotating the drum.
Liquid laundry products do not
flow in.
Is liquid laundry product put in the correct
compartment of the dispenser?
MAX
SOFTENER
YES
Is the cap clogged?
YES
Explain proper use of liquid laundry products.
Clean the compartment.
Visit to service.
21
8-2. FAULT DIAGNOSIS AND TROUBLESHOOTING
CAUTION
1. Be careful of electric shock if disconnecting parts while troubleshooting.
2. First of all, check the connection of each electrical terminal with the wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, reinsert the connectors correctly.
NO POWER
Is the supplied voltage 120 V AC?
NO
Check the fuse or reset
the circuit breaker.
NO
Replace the FILTER
ASSEMBLY (CIRC).
NO
Replace MAIN PWB
ASSEMBLY.
YES
Reconnect.
NO
Replace the MAIN PWB
ASSEMBLY.
YES
Connector
Is the voltage between the 2 FILTER ASSEMBLY
connectors 120 V AC?
WH
BL
YL
WH
WH
BK
YL
BL
BK
YL
RD
RD
BL
SB
YES
BL
WH
RD
Is the LED (1) on?
SB
SB
WH
SB
WH
WH
BL
YL
WH
BL
WH
WH
BK
YL
BL
BK
YL
RD
RD
BL
SB
YES
RD
Are the connectors (2) on the PWB loose?
SB
SB
WH
SB
WH
NO
Is wire of the DISPLAY PWB ASSEMBLY
broken?
YES
Replace DISPLAY PWB ASSEMBLY
or repair wire.
22
VIBRATION & NOISE IN SPIN
Have all the transit bolts and base packing
been removed?
NO
Remove the transit bolts
and Base packing.
NO
Move the washer or
reinforce the floor.
YES
Is the washer installed on a solidly constructed
floor?
YES
Base Packing
Level
Check if the washer is perfectly level as follows:
Check the leveling of the washer with a Level
and check that the washer is stable.
Put an unbalance part (rubber) inside of drum
and start QC test mode and run in high spin
(Refer to section 7-2).
When the machine is spinning in high speed,
verify that it is stable.
Unbalance Part
Tighten
If you do not have the unbalance part, put 4.5 to
6.5 lbs (2 to 3 kg) of clothing. Once loaded,
press power, Rinse+Spin and the start/pause
button in sequence.
When the machine is spinning in high speed,
verify that it is stable.
YES
If it is not stable, adjust feet accordingly. After
the washer is level, tighten the lock nuts up
against of the base of the washer. All lock nuts
must be tightened.
Tighten
23
NO WATER SUPPLY
Is water supply shut-off?
NO
Is the tap opened?
NO
Open the tap.
YES
Check the AIR CHAMBER
and the tube (clogged).
YES
Clean the filter.
NO
Replace the INLET VALVE
ASSEMBLY.
NO
Check electrical connection.
Replace the MAIN PWB
ASSEMBLY.
YES
When you press both WASH/RINSE button and
SOIL LEVEL button simultaneously, is the water
level frequency below 246?
NO
Is the inlet valve filter clogged?
NO
Is resistance between each terminal of INLET
VALVE ASSEMBLY 0.8-1.2 kΩ?
5
YES
Verify the voltage of the inlet valve connector is
120 V AC.
4
Bleach
Steam
(Refer to 7-2 QC TEST MODE)
DETERGENT DOES NOT FLOW IN
NO
Is water supplied?
YES
Bleach
Steam
MAX
SOFTENER
Are receptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?
YES
NO
Refer to
^NO WATER SUPPLY_
Check the wiring.
Put the detergent in the
correct place.
Has detergent been put in the correct compartment
NO
of the dispenser?
YES
Is the detergent caked or hardened?
24
YES
Clean the dispenser.
LIQUID DETERGENT/SOFTENER/BLEACH DOES NOT FLOW IN
Refer to
^NO WATER SUPPLY_
Is water supplied?
Bleach
Steam
MAX
SOFTENER
Bleach cap
SOFTENER
Are the plugs correctly connected to the terminals of
the INLET VALVE ASSEMBLY?
Check the wiring on the
dispenser.
Is liquid detergent/softener/bleach put in the correct
compartment of the drawer?
Put it in the correct
compartment.
Is the liquid detergent/softener/bleach cap clogged?
Clean the Cap and
Container.
MAX
SOFTENER
Softener
cap
Liquid detergent cap
ABNORMAL SOUND
Is the motor bolt loosened?
Secure the bolt.
Is there friction noise coming from the motor?
Replace the STATOR
ASSEMBLY or ROTOR
ASSEMBLY.
25
HEATING WITHOUT WATER
WH
BL
YL
WH
YES
Replace the MAIN PWB
ASSEMBLY.
YES
Repair the DRAIN HOSE
ASSEMBLY.
YES
Remove foreign material.
YES
Reconnect or repair the
connector
YES
Replace the DRAIN
PUMP ASSEMBLY.
NO
Replace the MAIN PWB
ASSEMBLY.
YES
WH
BK
YL
BL
BK
NO
Replace the
SENSOR SWITCH
ASSEMBLY.
YL
RD
RD
BL
SB
When pressing WASH/RINSE and SOIL LEVEL at the
same time after draining, is the water level frequency
255?
When pressing WASH/RINSE and SOIL LEVEL
buttons at the same time while washing, is the water
level frequency between 230 - 243 ?
BL
WH
RD
SB
SB
WH
SB
WH
Check the voltage between two pins while pressing
the POWER button. Is the voltage 120 V AC?
DRAIN MALFUNCTION
Is the drain hose twisted or frozen?
NO
Is the impeller of the drain pump clogged?
NO
Is the connector disconnected, disassembled?
NO
WH
BL
YL
WH
WH
BL
WH
RD
SB
SB
WH
NO
BK
YL
BL
BK
YL
RD
RD
BL
SB
Is the coil of the drain pump too high or low?
(resistance of the coil is 10-20 Ω)
SB
When checking voltage between connectors during
WH
spin, is the voltage 120 V AC as in the figure?
26
WASH HEATER TROUBLE
WH
BL
BL
BK
YL
YL
WH
RD
BK
RD
BL
WH
SB
YL
BL
WH
RD
SB
SB
WH
SB
WH
Replace the
Heater Assembly
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
and
SOIL LEVEL at the same time
Extra Hot: 70 °C
***
***
***
***
***
***
***
***
***
***
***
***
***
Water Temperature [°C]
WH
BL
BL
BK
YL
YL
WH
RD
BK
RD
BL
WH
SB
YL
BL
WH
RD
SB
SB
WH
SB
WH
(1)
When checking the THERMISTOR on the tub,
is the THERMISTOR loose?
27
Push the THERMISTOR
tightly to the rubber.
WILL NOT CIRCULATE WATER
Is the impeller of the drain pump clogged?
Hose Connector
(Water circulation
Hose & Steam Nozzle)
YES
Remove foreign material.
YES
Remove foreign material.
YES
Reconnect or repair
the connector.
YES
Replace PUMP MOTOR
ASSEMBLY.
NO
Replace the MAIN PWB
ASSEMBLY.
NO
Are the Hose Connector and/or Hose clogged?
NO
Connector
Is the connector disconnected, disassembled?
NO
Connector
WH
BL
YL
WH
WH
BL
WH
RD
SB
SB
WH
NO
BK
YL
BL
BK
YL
RD
RD
BL
SB
Is the coil of the right side of drain pump open
or short circuited? (Coil R is 18-30 Ω)
SB
WH
When checking voltage between the
connectors during spin, is the voltage 120 V AC,
as the figure?
28
SPIN TROUBLE
Check during spin if the frequency of the water
level is 248 or more.
BL
WH
BL
Check the SENSOR SWITCH
ASSEMBLY or HOSE (Pressure).
If the problem is on the SENSOR
SWITCH ASSEMBLY or the
HOSE, replace the SENSOR
SWITCH ASSEMBLY or the
HOSE.
Press the START/PAUSE button 2 times in QC
Test mode, is the drum spinning at low speed?
Normal
Is it disconnected, or disassembled?
[Red: 3pin (1), NA: 4pin (2)]
Correct the connection.
BK
YL
YL
WH
RD
BK
RD
BL
WH
SB
YL
BL
WH
RD
SB
SB
WH
SB
WH
(1)
(2)
Check the motor connector, Is the resistance of
the terminal the same as the figure?
MOTOR TERMINAL
Replace the STATOR
ASSEMBLY
Resistance of terminal:
- / - / - : About 5 Ω -15 Ω
Replace the MAIN PWB ASSEMBLY
BL
WH
BL
Does the spring of Latch Hook actuate?
Replace Door Assembly.
Is there clicking sound once or twice when the
START/PAUSE button is pressed to start the cycle?
Check the DOOR SWITCH
ASSEMBLY Connector and
MAIN PWB ASSEMBLY
(Red 3 pin, Yellow 4 pin and
white 3 pin connector (1)).
Is DOOR SWITCH ASSEMBLY broken?
Replace the DOOR
SWITCH ASSEMBLY.
BK
YL
YL
WH
RD
BK
RD
BL
WH
SB
YL
BL
WH
RD
SB
SB
WH
SB
WH
29
9. DISASSEMBLY INSTRUCTIONS
Be sure to unplug the machine out of the outlet before disassembling and repairing the parts.
CONTROL PANEL ASSEMBLY
TOP PLATE ASSEMBLY
① Unscrew 2 screws on the back of the top plate.
② Pull the top plate backward and upward as shown.
③ Disconnect the Display PWB Assembly connector
from Trans cable.
④ Pull out the drawer and unscrew 2 screws.
DRAWER
CONTROL PANEL ASSEMBLY
⑤ Taking out 1 screw.
⑥ Lift the side the Control Panel Assembly and
pull it out
CONTROL PANEL ASSEMBLY
⑦ Unscrew the 8 screws from the Control Panel
DISPLAY PWB ASSEMBLY
Assembly.
⑧ Disassemble the Display PWB Assembly.
30
MAIN PWB ASSEMBLY
① Disconnect the POWER connector and SENSOR
SWITCH ASSEMBLY.
② Remove the Protect Cover.
PROTECT COVER
③ Disconnect the connectors.
④ Unscrew 1 screw on the back.
⑤ Disassemble the Main PWB.
31
DISPENSER ASSEMBLY
① Disassemble the top plate assembly.
② Pull out the drawer.
③ Push out the DISPENSER ASSEMBLY after
unscrew 2 screws.
④ Unscrew the nut at the lower part of the dispenser.
⑤ Disassemble the 4 connectors from the valves.
※ Wire Color
① Blue Housing (YL-BK)
5
② Red Housing(VT-BK)
③ White Housing(WH-BK)
④ Blue Housing(GY-BK)
Red Housing(BL-BK)
⑥ Unscrew 2 screws from the back of the cabinet.
NOISE FILTER
① Disassemble two (or three) connectors from
the NOISE FILTER.
② Unscrew a screw from the TOP BRACKET.
32
CABINET COVER
① Unscrew the 5 screws from upper of the canbinet
cover.
② Unscrew the screw from filter cover.
③ Put a flat ( - ) screwdriver or putty knife into the both
sides of the filter cover, and pull it out.
④ Unscrew the screw from the lower side of the cabinet
cover.
33
⑤ Open the door.
⑥ Disassemble the clamp assembly.
⑦ Tilt the cabinet cover.
⑧ Disconnect the door switch connector.
※ NOTE: When assembling the CABINET
COVER, connect the connector.
⑨ Lift and separate the cabinet cover.
⑩ Disassemble the clamp assembly.
⑪ Disassemble the Gasket.
34
DOOR
① Open the door.
② Unscrew the 7 screws from the HINGE COVER.
③ Put a flat ( - ) screwdriver into the openng of the hinge,
and pull out the hinge cover.
④ Unscrew a screw from the lower side of door.
⑤ Disassemble the door upward.
※ Be careful! The door is heavy.
DOOR LOCK SWITCH ASSEMBLY
① Open the door and disassemble the CLAMP
ASSEMBLY.
② Unscrew the 2 screws.
※ NOTE
• Reconnect the connector after replacing the
DOOR SWITCH ASSEMBLY.
35
PUMP
① Disassemble the cabinet cover.
② Separate the pump hose, the bellows
and the circulation hose assembly from the
pump assembly.
③ Disassemble the pump assembly in arrow
direction.
HEATER
① Disassemble the cabinet cover.
② Separate 2 connectors from the heater.
③ Loosen the nut and pull out the heater.
※ CAUTION
• When assembling the heater, insert the
heater into the heater clip on the bottom of
the tub.
• Tighten the fastening nut so the heater is
secure.
36
WHEN FOREIGN OBJECT IS STUCK BETWEEN DRUM AND TUB
① Disassemble the cabinet cover.
② Separate the heater from the tub.
③ Remove any foreign objects (wire, coin, etc.) by
inserting a long bar in the opening.
LAMP ASSEMBLY
TOP PLATE ASSEMBLY
① Unscrew 2 screws on the back of the top plate.
② Pull the top plate backward and upward as shown.
③ Disconnect the connector.
Disassemble the lamp assembly.
37
MOTOR/DAMPER
① Disassemble the back cover.
② Remove the bolt.
③ Pull out the Rotor.
① Unscrew the 2 screws from the tub bracket.
② Remove the 6 bolts on the stator.
③ Unplug the 2 connectors from the stator.
① Disassemble the damper hinges from the tub
and base.
② Separate the dampers.
※ NOTE
• Once removed, replace the damper with
new one.
38
Checking the TSG (TURBO STEAM GENERATOR)
① To check out the fault diagnosis of TSG, in case
of removing the water inside, you can pull out
the plug and let the water drain away.
② Be cautious in case of the TSG is hot
temperature.
TSG (TURBO STEAM GENERATOR)
① Remove the housing coupled the TSG
(Heater, Water level frequency-sensor,
Thermistor)
② Taking out the screw of the TSG and Body
Frame.
39
③ Taking out the screws of Body Frame (2EA)
④ Separate the hoses from the TSG.
⑤ Remove the Body Frame and then, separate the
TSG from the washer
40
10. EXPLODED VIEW
10-1. CABINET & CONTROL PANEL ASSEMBLY
M400
M410
F215
A485
F210
A455
F110
A450
A104
A106
A102
A110 A111
A410
A105
A103
A150
A154
A152
A101
A141
A151
A153
A390
A100
A131
A130
A430
A140
A133
A440
A155
A300
A310
A201
A220
A303
A200
41
10-2. DRUM & TUB ASSEMBLY
K351
K350
K360
K143
K123
F140
K610
K411
K410
K611
K115
F466
K110
K141
K111
K140
K117
F315
K572
F310
K571
F465
K570
F463
K513
K122
F464
K125
K130
K320
K530
K121
K510
K512
K560
K135
K131
F328
K340
F467
K105
K520
K550
F461
K342
K346
K344
K345
F145
41
F468
K540
10-3.DISPENSER ASSEMBLY
F323
F322
F462
F321
F300
F170
F160
F227
F226
F327
F225
F430
F220
F441
F120
A275
A276
HOT (RED)
F130
COLD (BLUE)
F432
43