Eveready TFH 03 Table Fan User Manual

EVEREADY
Appliances
TABLE, WALL &
WFH O3
EVEREADY >>> PFH 03
INDUSTRIES INDIA LTD.
1, Middleton Street, Kolkata-700071, India
Consumer Care - address as above - Ph. 1800-102-4041 2 YEAR US E R MAN UAL
Email: [email protected] * Images are only indicative.
Actual product may differ from the one shown on the carton.
IMPORTANT SAFEGUARDS
This product is designed and intended for household use only.
Please read all the instructions carefully before using Eveready
Table, Wall and Pedestal fans, even if you are familiar with the
product then also keep it handy for future reference.
1. Assemble the fan before switching it on.
2. Disconnect the fan before moving from one location to another.
3. Do not insert fingers, pencils or any other object through the
guard when the fan is running.
4. Do not use fan near an open window. Rain water may cause
electrical hazards.
5. Place it on a stable flat surface when operating.
ASSEMBLY & OPERATION
W- W- ur
Step - 1 Step -2 Step - 3 Step - 4
Assembling Blades and Crill
ASSEMBLY & OPERATION
ASSEMBLY INSTRUCTIONS FOR
BLADES AND GRILL
eo Unscrew the spinner clockwise and plastic nut counter
clockwise before removing both of them
е Set the back guard in proper position with handles up
e Screw the plastic nut tightly to attach the back guard
e Install the blade on to the motor shaft until it reaches the
retaining pin
e Secure both guards tightly with the plastic ring before
tightening the screw at the bottom of the ring
ASSEMBLY OF TABLE FAN
e Insert the stand to the base
e Fix the screws at the bottom of the base to secure the stand
firmly
ASSEMBLY OF WALL FAN
e Attach the mounting bracket firmly to the wall
e Mount the fan to the bracket by the clamp from behind the
stand
ASSEMBLY OF PEDESTAL FAN
e Attach the pipe to the base
e Fix the bolt at the bottom of the base to secure the pipe firmly
e Pull out the inner pipe and tighten the height adjustment knob
e Place the fan body on the inner pipe and tighten it properly with
the knob
PARTS IDENTIFICATION
HEY
So
Eu
a.
: A
©
—©
ооо ее
Blade
Handle
Push Button for Oscillation
Motor
Vertical Tilt Adjustment Screw
Base
Speed Control Switch
Grill Lock
Grill
PARTS IDENTIFICATION
® Blade
Motor
(© Vertical Tilt Adjustment
Screw
(D Speed Control Knob
(E) Pull string for Speed and
Oscillation Control
(® Grill Lock
© Grill
PARTS IDENTIFICATION
NOOO
Blade
Handle
Push Button for Oscillation
Motor
Vertical Tilt Adjustment Screw
Speed Control Button
Height Adjustment Lock
Base
Grill Lock
Grill
TABLE FAN
TECHNICAL SPECIFICATION
OPERATING INSTRUCTIONS ModelN TEH 03 WEH 03 PEH 03
e Plug the power supply cord into the wall outlet for 230V, 50Hz, обе! INO.
AC Supply
Control the Speed by pressing the push buttons Power 120W 120W 120W
To start / stop fan oscillation, push down / pull up the oscillation Voltage 230V. 50 Hz 230V. 50 Hz 230V. 50 Hz
knob ’ ’ ’
e Adjust the airflow upward and downward after loosening the :
titing knob; push the guard lightly to the desired angle and Air Delivery 85 CMM 85 CMM 85 CMM
tighten the tilting knob
Speed 2100 RPM 2100 RPM 2100 RPM
WALL FAN
OPERATING INSTRUCTIONS
Plug the power supply cord into the wall outlet for 230V, 50 Hz,
AC supply
Adjust the desired speed by pulling the speed control string
To start or stop the fan oscillation, pull the oscillation control
string
Adjust the airflow upward and downward after loosening the
tilting knob; push the guard lightly to the desired angle and
tighten the tilting knob
PEDESTAL FAN
OPERATING INSTRUCTIONS
e Plug the power supply cord into the wall outlet fo 230V,
50 Hz, AC supply
Control the speed by pressing the push buttons
To start / stop fan oscillation, push down / pull up the oscillation
knob
Adjust the airflow upward and downward only after loosening
the tilting knob; push the guard lightly to the desired angle and
tighten the tilting knob