tangenttm table ensemble
TANGENT TABLE ENSEMBLE
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
MATERIALS INCLUDED
a
b
e
TOOLS NEEDED
steel wire brush
c
7/32" hex bit for
tamper-resistant screws
f
d
3/16, 3/8 & 1/2 drill
bits for concrete
Loctite
STEP BY STEP
pencil
1/4" punch
3/16" hex key
hammer drill
hammer
FOR ALL SURFACE MOUNTED TANGENT TABLE ENSEMBLES (SETAN-4BS SHOWN)
bb
bb
4 per leg
2 per leg
Attach legs to central hub
Attach top bracket to legs
• Attach legs to central hub with 1/4"-20 x 3/4" flat socket-cap
screws (b) using drill and 7/32" hex bit for tamper-resistant screws
(provided). • Attach top bracket to legs with 1/4"-20 x 3/4" flat socket-cap
screws (b) using drill and 7/32" hex bit for tamper-resistant
screws. cc
Attach table top to top bracket
Mark hole locations
• Attach table top to top bracket with 3/8"-16 x 3/4" button head
cap screws (c) using drill and 7/32" hex bit for tamper-resistant
screws. Note that 4-seat ensembles will use 8 flat socket-cap
screws, and 6-seat ensembles will use 6 flat socket-cap screws.
• Place table ensemble in desired location. Mark center of each hole
location with a pencil.
T 800.451.0410 | www.forms-surfaces.com
© 2013 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 3 | Rev. 05-23-13
TANGENT TABLE ENSEMBLE
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR ALL SURFACE MOUNTED TANGENT TABLE ENSEMBLES (SETAN-4BS SHOWN)
f
Drill anchor holes
Insert and set anchors
• Use hammer drill to drill 1-7/8" deep x 1/2" diameter anchor holes
at each marked location using a 1/2" drill bit suitable for concrete
drilling.
• Use steel wire brush to clean each anchor hole.
NOTE: Forms+Surfaces recommends starting holes with 3/16"
diameter drill bit followed by 3/8" and finally 1/2" for maximum
accuracy.
7
• Insert 3/8"-16 x 1-1/2" anchor (f) into each hole and use hammer
to tap anchor tops flush with ground level.
• Use 1/4" punch and hammer to set anchors by driving down the
center of each anchor until it stops.
8
a
Position ensemble
Attach ensemble
• Position ensemble so that mounting holes line up with anchors.
• Insert 3/8"-16 x 3" tamper-resistant flat socket-cap screws (a)
into mounting holes in ensemble and thread into anchors using
provided 7/32" hex bit for tamper-resistant screws.
T 800.451.0410 | www.forms-surfaces.com
© 2013 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 3 | Rev. 05-23-13
TANGENT TABLE ENSEMBLE
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR ALL SURFACE MOUNTED TANGENT TABLE ENSEMBLES (SETAN-4BS SHOWN)
10
9
e
Tighten screws
Attach seats to seat cradle brackets
• Tighten all screws until snug.
• Attach seats to seat cradle brackets with 3/8"-16 x 3/4" button
head cap screws (e) using a drill and 7/32" hex bit for tamperresistant screws. Note that the indicator arrow on the seat cradle
bracket should be pointing towards the front of the seat.
11
d
Attach seats to legs
Tighten screws
• Attach seat cradles to legs with with 3/8"-16 x 1" flat socket-cap
screws (d) using a drill and 7/32" hex bit for tamper-resistant
screws.
• Tighten all screws until snug.
T 800.451.0410 | www.forms-surfaces.com
© 2013 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 3 | Rev. 05-23-13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement