Conflicts - cloudfront.net

Conflicts - cloudfront.net
Doc. 14.151.00
TOYOTA
Business Partner: L12
PIO / DIO
2016
Tacoma
02/22/16
Chrome Tailgate Letter Inserts
Part Number: 00016-35071
Accessory Code: JB2200
Conflicts
Color Applicability/Trim Level
Accessory
Color
Note:
Kit Contents
Item #
1
2
3
4
5
6
7
8
Quantity Reqd.
1
Description
Tacoma Tailgate Logo
Vehicle/Trim Color
Hardware Bag Contents
Item #
1
2
3
4
5
6
7
8
Quantity Reqd.
Description
General Applicability
Recommended Sequence of Application
Item #
1
2
3
*Mandatory
Additional Items Required For Installation
Item #
Accessory
Quantity Reqd.
Description
Recommended Tools
Safety Tools
Special Tools
Installation Tools
2” Rubber Roller
Clean Lint Free Cloth
Special Chemicals
Alcohol/Water 50/50 Mix
Southeast Toyota Distributors, LLC
Page 1 of 4
TOYOTA
Tacoma
Chrome Tailgate Letter Inserts
Procedure
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation o f
this accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, re-checking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Vehicle Preparation
Note: The room, parts & vehicle temperature must be between 60 & 90 degree F for optimum
installation.
1. Clean area of application – recessed TACOMA area in
Tailgate – with 50/50 alcohol-water solution. Dry Application
area with a clean lint-free wipe. Discard the wipe after a single
use. Fig. 1
INSTALLATION : TACOMA TAILGATE:
1.
Fig. 1
Remove clear protective cover on top of letters. Fig. 2
Fig. 2
2. Then carefully remove spacing template surrounding letters.
Fig. 3 & 4.
Fig. 3
Southeast Toyota Distributors, LLC
Page 2 of 4
Fig. 4
TOYOTA
Chrome Tailgate Letter Inserts
Tacoma
3. Remove letters without touching adhesive on back;
remove one letter at a time. Fig. 5.
Fig. 5
4. Install each letter by lining up edge & centering in
opening of stamped area in tailgate. Fig. 6. After
checking to insure the letter is centered & level, press
firmly to insure adhesion.
SPECIAL NOTE: PAY SPECIAL ATTENTION TO
THIN STROKES OF THE LETTER “C” TO KEEP
THEM STRAIGHT. FIG. 7
5.
6.
After all letters have been applied, placed a clean cloth
over the letters & gently roll with a 2” rubber roller.
The TACOMA logo has been successfully applied. Fig. 8
Southeast Toyota Distributors, LLC
Page 3 of 4
Fig. 6
Fig. 7
Fig. 7
TOYOTA
Chrome Tailgate Letter Inserts
Tacoma
Audit Criteria
1. Vehicle to Graphic Compatibility:
1.1 Vehicle must have the appropriate Tacoma Tailgate Logo.
2. Cleanliness Under Graphic Surface:
2.1 Surface under & around the around the graphic application area
must be clean & free of foreign materials.
3.
Alignment:
3.1 Tacoma Tailgate Logo must maintain consistency in placement & alignment on unit.
4. Uniform & Consistent Adhesion:
4.1 All letters, especially corners, must be completely & evenly adhered to vehicle surface.
No edges lifting are allowed.
Southeast Toyota Distributors, LLC
Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement