Installation, Use &amp
Installation, Use & Care Guide
30” and 36” Free-Standing Range Hood
Guia de Instalación, Uso y Cuidado
30” y 36” Campana extractora
Guide d’installation, utilisation et d’entretien
30” et 36” Hotte aspirante
RH30WC55GSB + RH36WC55GSB
316495102
2
Finding Information
Please read and save this guide
Thank you for choosing Electr
Electrolux
olux, the new premium brand in home appliances. This Use & Care Guide is
olux
part of our commitment to customer satisfaction and product quality throughout the service life of your new
appliance.
We view your purchase as the beginning of a relationship. To ensure our ability to continue serving you,
please use this page to record important product information.
Keep a rrecor
ecor
d for quick rrefer
efer
ence
ecord
eference
Purchase date
Model number
NOTE
Registering your product with Electrolux enhances
our ability to serve you. You can register online at
www.electroluxappliances.com by dropping your
Product Registration Card in the mail.
Serial number (see picture for location)
Questions?
For toll-free telephone support in the U.S. and Canada:
(1-877-435-3287)
For online support and Internet product information visit http://www.electroluxappliances.com
Table of contents
Important Safety Instructions ..................................... 3-4
ements ........................... 5
Electrical & Installation r equir
equirements
Electrical requirements ........................................................... 5
Before installing the hood ................................................... 5
List of Materials .................................................................... 6
Parts Included with your Hood .......................................... 6
Optional Accessories ............................................................ 6
Tools/Materials required ....................................................... 6
Installing the hood ....................................................... 7-13
Installing preparation.............................................................. 7
Wall framing for adequate support .................................. 7
Removing the packaging .................................................... 7
Examples of possible ducting ........................................... 8
Ductwork installation guidelines ....................................... 8
Ductwork and wiring locations .......................................... 8
Mounting the duct cover bracket ..................................... 9
Ceiling ducting ........................................................................ 10
Wall ducting ............................................................................. 10
House wiring location ......................................................... 10
Install framing for hood support ..................................... 10
Mounting the hood .............................................................. 10
Connecting the ductwork ................................................. 11
Air deflector installation
(Recirculating accessories) .................................................. 11
©2007 Electrolux Home Products, Inc.
Making the electrical connections ................................. 12
Mounting the duct cover.................................................... 13
es ................................................................................. 14
Featur
Features
ol buttons .................................................................. 15
Contr
Control
Special functions ............................................................... 16
Clock programming .............................................................. 16
Grease filter saturation alarm ............................................. 16
Charcoal filter saturation alarm
(Recirculating accessories) .............................................. 16
Audible signal activation and deactivation ................ 16
Charcoal filter inclusion and exclusion
(Recirculating acc essories) ............................................... 16
Heat sensor.............................................................................. 16
For Best results ...................................................................... 17
Car e and cleaning ............................................................ 18
Filters ......................................................................................... 18
Lights ......................................................................................... 18
Optional Charcoal Filters ................................................... 19
Charcoal filter placement
(Recirculating acc essories) ............................................... 19
Cleaning ................................................................................... 19
Hood Surface ........................................................................ 19
Warranty Information ....................................................... 20
All rights reserved. Printed in Mexico
Important Safety Instructions
Important Safety Instructions
e using this
Read all instructions befor
before
appliance.
Save these instructions for futur e
ence.
r efer
eference.
esidential appliances
Approved
oved for rresidential
Appr
For r esidential use only
Do not attempt to install or operate your appliance
until you have read the safety precautions in this
manual. Safety items throughout this manual are
labeled with a WARNING or CAUTION based on the
risk type.
This symbol alerts you to
situations that may cause
serious body harm, death
or property damage.
This symbol alerts you to
situations that may cause
bodily injury or property
damage.
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: Turn off power circuit at service panel and lock out panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit
3
4
Important safety Instructions
READ AND SAVE THESE INSTRUCTIONS
Important safety Instructions
FOR GENERAL VENTILATING USEDO
ONLY
NOT
. USE
TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
B. Before servicing or cleaning the unit, switch power o$
at service panel and lock service panel disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
C. Installation Work and Electrical Wiring Must Be Done
By Quali#ed Person(s) In Accordance With All Applicable Codes & Standards, Including Fire-rated Construction.
D. Su%cient air is needed for proper combustion and exhausting of gases through the "ue (Chimney) of fuel
burning equipment to prevent back- drafting. Follow
the heating equipment manufacturers guideline and
safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
E. When cutting or drilling into wall or ceiling, do not damage electrical wiringand other hidden utilities.
F. Ducted systems must always be vented to the outdoor
s.
To reduce risk of "re and to properly exhaust air, be
sure to duct air outside - do not vent exhaust air into
spaces within walls, ceilings, attics, crawl, spaces
or
garages.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCT WORK.
Install this hood in accordance with all requirements speci#ed.
To Reduce The Risk Of Fire Or Electric Shock, Do Not
Use This Hood With Any External Solid State Speed
Control Device.
o Reduce The
Automatically Operated Device - TTo
Risk Of Injury Disconnect Fr om Power Supply
Befor e Servicing.
TO REDUCE THE RISK OF A RANGE TOP GREASE
FIRE.
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that
may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or
when "ambeing food (I.e. Crepes Suzette, Cherries
Jubilee, Peppercorn Beef Flambe’).
c) Clean ventilating fans frequently. Grease should not
be allowed to accumulate on fan or #lter.
d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS, IN
THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING
:
a) SMOTHER FLAMES with a close-#tting lid, cookie
sheet, or other metal tray, then turn o$ the gas burner
or the electric element. BE CAREFUL TO PREVENT
BURNS. If the "ames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - you may be
burned.
c) DO NOT USE WATER, including wet dishcloths or
- tow
els - a violent steam explosion will result.
d) Use an extinguisherONLY if:
1) You know you have a class ABC extinguisher, and
you already know how to operate it.
2) The #re is small and contained in the area where it
started.
3) The #re department is being called.
4) You can #ght the #re with your back to an exit.
OPERATION
a. Always leave safety grills and #lters in place. Without
these components, operating blowers could catch ont
o hair,
#ngers and loose clothing.
The manufacturer declines all responsibility in the event
of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The
manufacturer further declines all responsibility for injury
due to negligence and the warranty of the unit automatically expires due to improper maintenance.
Important safety Instructions - Electrical & Installation
requirements
READ AND SAVE THESE INSTRUCTIONS
Electrical & Installation requirements
ements
equir
Electrical rrequir
equirements
Before installing the hood
IMPOR T ANT
1. For the most efficient air flow exhaust, use a
straight run or as few elbows as possible.
Observe all governing codes and ordinances.
It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate
and in conformance with National Electrical Code,
ANSI/NFPA 70 — latest edition*, or CSA Standards
C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No.0-M91 - latest edition** and all local codes
and ordinances.
If codes permit and a separate ground wire is used, it
is recommended that a qualified electrician determine
that the ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure
range hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
IMPOR T ANT
Save Installation Instructions for electrical inspector’s
use.
The range hood must be connected with copper wire
only.
The range hood should be connected directly to the
fused disconnect (Or circuit breaker) box through
metal electrical conduit.
Wire sizes must conform to the requirements of the
National Electrical Code ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code Part 1 and C22.2 No. 0-M91 - latest edition** and all local codes and ordinances.
A U.L.- or C.S.A.-listed conduit connector must be
provided at each end of the power supply conduit (at
the range hood and at the junction box).
Copies of the standards listed may be obtained from:
* National Fire Protection Association Batterymarch Park Quincy,
Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575
Vent unit to outside of building, only.
2. At least two people are necessary for installation.
3. The hood is fitted with Screws and Drywall
Anchors suitable for most surfaces, consult a
Qualified Installer, check if they perfectly fit with
your cabinet/wall.
4. Do not use flex ducting.
5. COLD WEATHER installations should have an
additional backdraft damper installed to minimize
backward cold air flow and a nonmetallic thermal
break to minimize conduction of outside
temperatures as part of the ductwork. The
damper should be on the cold air side of the
thermal break.
The break should be as close as possible to
where the ducting enters the heated portion of
the house.
6. Make up air: Local building codes may require the
use of Make-Up Air Systems when using Ducted
Ventilation Systems greater than specified CFM of
air movement.
The specified CFM varies from locale to locale.
Consult your HVAC professional for specific
requirements in your area.
5
6
List of Materials
List of Materials
Parts Included with your Hood
Hood structure assembly with blower, transition.
Lamp already installed.
2 grease filters 30”or 3 grease filters 36”.
Duct covers.
Hardware bag with:
Template
Duct cover support bracket (1 piece)
Use, care and installation guide
Wood screws (6 pieces - 3/16" x 1" 3/4)
Concrete wall anchors (6 pieces - 3/8” X 13/8”)
Assembly screws (8 pieces)
Optional Accessories
Telescopic duct cover to fit ceiling height from 9'
to 10'
Re circulation KIT
Charcoal Filter
Tools/Materials required
Duct tape
Wire nuts
Tape to mount template
1/2” electrical connector (junction box)
8" rounded metal duct length to suit installation
Measuring tape
Pliers
Gloves
Knife
Safety glasses
Electric drill with 5/16” and 3/8” Bits
Strain relief
Spirit level
Duct tape
Screwdrivers:
Phillips (Posidrive) # 2
Torx # 2
Wire cutter/stripper
Masking tape
Hammer
Saw, jig saw or reciprocating saw
Installing the hood
Installing the hood
t For the most efficient air flow exhaust, use a
straight run or as few elbows as possible.
Vent unit to outside of building, only.
t On avarage 2 to 3 hours are necessary to complete installation (without considering cut to be
done on wall and or on cabinet, installation of
ducts , conduit and electrical connections to the
mains).
t The hood is fitted with Screws and Drywall
Anchors suitable for most surfaces, consult a
Qualified Installer, check if they perfectly fit with
your cabinet/wall.
t Do not use flex ducting.
t COLD WEATHER installations should have an
additional backdraft damper installed to minimize
backward cold air flow and a nonmetallic thermal
break to minimize conduction of outside
temperatures as part of the ductwork. The
damper should be on the cold air side of the
thermal break.
The break should be as close as possible to
where the ducting enters the heated portion of
the house.
t Make up air: Local building codes may require the
use of Make-Up Air Systems when using Ducted
Ventilation Systems greater than specified CFM of
air movement.
The specified CFM varies from locale to locale.
Consult your HVAC professional for specific
requirements in your area.
t
Typical installation
Min installation height from the range top to the
bottom of the hood is 30" if a gas range is used
or 24" to 30" if an electric range is used.
These hoods ar e not rrecommended
ecommended to be used
over indoor grills.
The hood may be installed onto a wall and vented to
the outdoors, or it can be installed for recirculating
operation (recirculating accessories not supplied with
the hood).
This hood can be installed over any electric and gas
cooktop/range.
It can not be installed over any pr ofessional
cooktop / range.
eparation
Installing pr
preparation
Advance planning
t Determine the exact location of the vent hood.
t Plan the route for venting exhaust to the
outdoors.
t Use the shortest and straightest duct route
possible.
guidelines”
Refer to “ Ductwork installation guidelines
paragraph for further informations.
t Install a wall cap with damper or roof cap at the
exterior opening. Order the wall or roof cap and
anytransition needed in advance.
t Use 8" round metal ductwork only.
W all framing for adequate support
t This vent hood is heavy.
‘Adequate structure and support must be
provided in all types of installations. Thehood
must be secure to vertical studs in the wall, or to
a horizontal support.
t The vent hood should be on site before final
framing and wall finishing. This will help to
accurately locatethe duct work and electrical
service.
t Installation will be easier if the vent hood is
installed before the cook-top and countertop are
installed.
Removing the packaging
Remove carton carefully, Wear gloves to protect
against sharp edges.
Remove the protective film covering the product
before putting into operation.
7
8
Installing the hood
Examples of possible ducting
Ductwork installation guidelines
Ductwork and wiring locations
For safety reasons, ducting should vent directly
outdoors (not into an attic, underneath the house,
into the garage or into any enclosed space).
Keep duct runs as short and straight as possible.
Duct fittings (elbows and transitions) reduce air flow
efficiency.
Back to back elbows and “S“ turns give very poor
delivery and are not recommended.
A short straight length of duct at the inlet of the
remote blower gives the best delivery.
Transition to duct from the integral blower or remote
duct transition as close to the downdraft as is possible.
In order of preference, use
1st. 10" round duct
2nd. 8" round duct
3rd. 3-1/4" x 14" duct
4th. 7" round duct
5th. 3-1/4" x l0" duct
6th. 6" round duct
t Determine the exact location of the vent hood.
t Locate the template packed with the literature.
t Installation height: 30" gas cooktop/range or 24"
to 30" electric cooktop/range.
t Use a level to draw a horizontal straight pencil line
on the wall, which is your desired
installationheight.
t Find the centerline of the cooktop. Use a level to
draw a vertical straight pencil line on the wall.
Y
CHECK TO BE SURE THE LINE IS PERFECTL
PERFECTLY
PERPERNDICULAR.
The use of flexible metal round duct should only be
used when no other duct fitting exists. Limit use to
short lengths and do not crush when making
corners.
Installing the hood
Mounting the duct cover bracket
Ceiling ducting
The duct cover bracket should be installed against
the back wall and flush with the ceiling. This bracket
will hold the telescopic duct cover in place at the top
(this a extra accessory available not included with the
hood).
If the duct will vent straight up to the ceiling:
t Use level to draw a line straight up, from the
centerline on the template to the ceiling.
t Measure at least 4 -3/4 ” from the back wall to
the circle center of an 8-½” hole on the ceiling.
Secur e the bracket to the wall:
t Align the marked centerline on the bracket with
the centerline on the wall.
t Mark 2 screw hole locations in the wall.
t Drill 5/16" pilot holes in the marked locations.
t Install wall fastener anchors.
t Drive wood screws, by hand, into the fastener to
allow anchors to expand. Remove the screws.
t Secure the bracket to the wall with wood screws
and/or fasteners.
W all ducting
If ductwork will vent to rear:
t Use a level to draw a line straight up from the
centerline on the template.
t Measure at least 23 - 3/4" (the measure might
vary dependig on the elbow used) above the
pencil line that indicates the bottom installation
height, to the circle center of an 8-½” diameter
duct hole (Hole may be elongated for duct elbow).
House wiring location
t The junction box is located on the top left side of
the hood.
t Wiring should enter the back wall at least 20"
above the bottom of the installation height, and
within 5-7/8" and 4-7/8"of the left side of the
centerline.
9
10
Installing the hood
Install framing for hood support
If drywall is present, mark the screw hole
locations. Remove the template.
Cut away enough drywall to expose 2 vertical
studs at the holes location indicated by the
template.
Install two horizontal supports at least 1”x 6”
between two wall studs at the bottom and top
mounting holes installation location.
Mounting the hood
Install the 8” round transition as shows the image below.
The installation screws and the 8” round transition are
included on the hood package.
8”
room side of the studs.
Use cleats behind both sides of the support to
secure to wall studs.
IMPORTANT:
Framing must be capable of supporting 100 lbs. 2 people are required to lift and position the hood
onto the mounting screws.
Place the template on the wall along the horizontal line, make sure the template is leveled and
centered with the centerline.
Mark “upper” screw holes locations in the wall.
IMPORTANT. Check to be sure that hole locations
are leveled and correctly centered by the vertical
centerline.
Drive “upper” wood screws by hand. Leave ¼ “ of
distance between the screw head and the wall.
onto the “upper” screws.
Mark “lower” wood
screw holes locations
in the wall using a
pencil.
Installing the hood
t Remove the hood.
t Drive “lower” wood screws, by hand. Remove
screws.
t Mount the hood onto the “upper” screws.
t Drive and tighten the “upper” wood screws, by
hand.
t Drive and tighten the “lower” wood screws, by
hand.
Air deflector installation
culating accessories)
(Recir
(Recirculating
t Assemble the air deflector with the duct cover
bracket with 4 assembly screws provided as
shown.
t Measure from the bottom of the air deflector to
the bottom of the hood outlet, as shown.
Connecting the ductwork
t Install ductwork, making connections in the
direction of airflow as illustrated.
t Push duct over the exhaust outlet.
t Wrap all duct joints and the flange connections
with duct tape for an airtight seal.
t Make the same connection in the wall or ceiling
vent exit.
t Cut the duct at the measured size.
t Uninstall the air deflector removing the 4
assembly screws.
t Slip the duct onto the bottom of the deflector.
t Place the assembled deflector and duct over the
exhaust outlet from the hood.
t Assemble the air deflector to the duct cover
bracket with 4 assembly screws provided as
shown.
11
12
Installing the hood
Making the electrical connections
If not already done, install 1/2” conduit connector
in j-box.
NOTE: This connector is not included with vent
hood.
Metal electrical
conduit
Electrical Shock Hazard
Warning: Turn off power at the service panel before
wiring this unit.
120 V AC, 15 or 20 Amp circuit required.
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN
ELECTRICAL JUNCTION BOX WITH 3 WIRES,
ONE OF WHICH (GREEN/YELLOW) SERVES TO
GROUND THE APPLIANCE. TO PROTECT YOU
AGAINST ELECTRIC SHOCK, THE GREEN AND
YELLOW WIRE MUST BE CONNECTED TO THE
GROUNDING WIRE IN YOUR HOME
ELECTRICAL SYSTEM, AND IT MUST UNDER
NO CIRCUMSTANCES BE CUT OR REMOVED.
Failure to do so can result in death or electrical
shock.
Remove junction box cover and knockout on the
top left side.
Knockout
Junction box
cover
House
wiring
UL listed
wire nut
Run black (live), white (neutral), and green (earth)
wires (#14 AWG) according to the National
Electrical Code or CSA Standards and local
codes and ordinances in 1/2” conduit from power
supply to j-box.
Connect black, white, and green wires from
power supply to black, white, and green/yellow
wires in j-box respectively.
These connections should be done while always
making reference to the electrical diagram found
inside the hood.
Close j-box cover and reapply
Installing the hood
Mounting the duct cover
t Position the duct cover over the mounted hood.
t Slide the bottom of the duct into the glass area.
t Position the top of the duct over the duct
mounting bracket. If a telescopic duct cover is
used, grab the upper part of the telescopic duct
cover, pull it and place it in the duct cover
mounting bracket.
t Secure the top of the duct with 2 assembly
screws provided.
t Secure the bottom of the duct with 2 assembly
screws provided.
Instal the grease filter and turn power on at service
panel. Check operation of the hood.
13
Features
14
Features
1.
2.
3.
4.
5.
6.
7.
Blower and light controls
Lamp housings
Grease filter Handle
Grease filter
Canopy
Duct covers
Louver holes (Only for Recirculating version)
Control buttons
15
Control buttons
This hood is equipped with an electronic motor and
lamp control.
The control is able to set 4 different fan speeds, turn
ON/OFF light and has a timer function.
In the following drawing are described the main key
functions.
button is pressed, the fan will be set to first
speed.
t If the fan is at third speed and the “
” key is
pressed, the fan will be set to second speed.
”
t If the fan is at fourth speed and the “
button is pressed, the fan will be set to third
speed.
” button is
t If the fan is OFF and the “
pressed, the control backlight will light up.
5. “
1. Light Button
t Press lamp button to turn ON the light (Lamp
state previously OFF).
t Press lamp button to turn OFF the light (Lamp
state previously ON).
2. Timer Button
t The default timer setting is 10 minutes, and it
can be adjusted between 20 minutes and
1minute.
t After pressing the timer button, the control
enters to a timer setup mode, and user can
adjust the timer countdown time with the
“
” and “
” buttons within 5 seconds.
The timer can be initiated immediately
pressing the timer button, after setting the
timer duration or pressing the timer button
twice (default 10 minutes setting).
t If no action occurs within 5 seconds, the
countdown will start.
t During the timer setup the “ ” and “
”
buttons are dedicated to the timer and no
motor action will occur.
t Once the timer is initiated, it can be cancelled
by pressing the timer button again.
3. Display
t Shows the hood settings.
4. “
” Button. Speed Decr ease / OFF
t This button is used to decrease the fan speed,
or turn OFF the fan.
” button is
t The fan will turn OFF if the “
pressed and the hood was in the first speed.
t If the fan is at second speed and the “
”
” Button. Speed Incr
ease / ON
Increase
t This button is used to increase the fan speed,
or turn ON the fan.
t The fan will turn ON if the “
” button is
pressed and the hood was OFF.
t If the fan is at first speed and the “
” button
is pressed, the fan will be set to second
speed.
t If the fan is at second speed and the “
”
button is pressed, the fan will be set to third
speed.
t If the fan is at third speed and the “
”
button is pressed, the fan will be set to fourth
speed.
t If the fan is at fourth speed and the “
”
button is pressed, a beep will sound.
Control buttons - Special functions
16
Special functions
ogramming
Clock pr
programming
t The clock can be reprogrammed at any time except during an active timed function.
t The clock can be displayed in a twelve hour format and valid clock times are from 1:00 to 12:59.
t The clock can be reprogrammed pressing the “ T imer
imer” button for 5 seconds, and after, the clock can be
adjusted with the “
” and “
” buttons. Colon “:” will flash indicating clock programming mode.
t The user can have minute increments / decrements of 1 minute, but if the user keep pressing the “
”/
”
” buttons for more than 1 second, the increments / decrements will be of 5 minutes.
During this option the control will round to the nearest 5 minutes.
t The user can finish on reprogramming the clock pressing the “ T imer
imer” button.
t After 1 minute of no button pressed the control will accept the programmed clock time and will add one
minute to the set clock.
Gr
ease filter saturation alarm
Grease
ease Filter
Gr
Filter” if the fan is active.
Grease
t After thirty fan functional hours, the display will show “Gr
When this icon is shown in the display, the grease filters installed are required to be washed.
t To reset the grease filter saturation alarm the user must press the “
” button for 5 seconds, after this
ease filter
filter” is not displayed, and the hood has the normal display operation.
Grease
action the icon “ Gr
Char
coal filter saturation alarm (Recir
culating accessories)
Charcoal
(Recirculating
t After one hundred and twenty functional hours of the fan, the display will show “ Char coal Filter
Filter” if the fan
is active. When this icon flashes on display, the charcoal filters installed are required to be replaced or
reactivated.
t To reset the charcoal filter saturation indication the user must press the “
” button for 5 seconds, after
filter” is not displayed and the hood has the normal display operation.
this time the icon “ Char coal filter
Audible signal activation and deactivation
Light
Light” button for 5 seconds.
t The audible signals can be activated or deactivated pressing the “Light
Snd
Snd” symbol must appear on the display for
t If the audible signal is activated, a tone must sound and the “Snd
2 seconds.
t If the audible signal is deactivated, the “ Snd
Snd” symbol must appear on the display for 2 seconds and no
tone must sound.
Char
coal filter inclusion and exclusion (Recir culating accessories)
Charcoal
t The charcoal filter inclusion or exclusion can be set by pressing the “
” and “
” buttons at the same
time for 5 seconds.
t The Inclusion or exclusion of charcoal filter must be selected while the lamps and the motor are OFF.
t When the charcoal filter has been excluded, the charcoal filter alarm is disabled.
Heat sensor
t The control is equipped with a heat sensor that will turn on the blower at second speed if excessive heat
occurs (over 158° F or 70°C
70°C) surrounding the control area.
t If the blower is OFF or if it is operating at first speed, the blower will be set automatically to second speed,
the display shows the word " CArE
CArE" to indicate that heat sensor has detected an excessive heat.
t During this state, the user may raise the blower speed to third speed but can not decrease the speed.
t When the temperature level on the hood drops to normal, the blower will operate in the setting defined by
the user before the alarm occured.
17
esults
For Best rresults
t
t
t
t
t
t
t
t
t
t
t
t
t
t
Continuous use of the fan system while cooking helps keep the kitchen comfortable and less humid.
It also reduces cooking odors and soiling moisture that create a frequent need for cleaning.
Turn the blower on before starting to cook.
Use a rear burner when browning or pan frying meat.
Open a window or inside door slightly.
Clean the filters and the wall behind the filters frequently.
e cooking in order to establish air currents upward
The blower should be turned on for a few minutes befor
before
through the hood. Thus when heat, smoke, moisture, grease and cooking odors are produced, they will
be carried outside instead of drifting into other rooms.
Use the low speeds for normal use and the higher speeds for strong odors or fumes.
Drafts across the range or cooktop will cause the escape of heat, smoke, moisture, grease and cooking
odors from the hood. Such drafts should be prevented in so far as possible.
The best job of ventilation in the kitchen is done where the only air currents are those created by the
blower itself.
For Gas Cooktops, a lower blower speed should be used if:
the gas flame is being distorted by the air movement.
the burner continually sparks (clicks)
the burner flame repeatedly blows out.
18
Care and cleaning
Care and cleaning
Lights
The frequency of cleaning depends on the amount
and type of cooking.
Do not use the ventilating system without the
surfaces.
Always unplug or disconnect the appliance from the
power supply before servicing.
Before replacing the lamps, switch power off at
service panel and lock service panel disconnecting
means to prevent power from being switched on
accidentally.
NOTE: Turn off the lights and fan. Allow the
lights to cool before handling. Replace lights
per instructions. If new lights do not operate,
be sure lights are inserted correctly before
calling service.
Replace Lights
• Remove the inner lamp lens cover by inserting a
attempting to clean any part of the appliance.
slots and gently prying it free.
NOTE: Do not remove the outer trim ring (lamp
assembly).
Filters
Outer
ring
Inner
ring
anodized aluminum and are long lasting.
ease Filters
To Remove The Metal Gr
Grease
Pull the spring release handle.
The glass lens and inner trim ring are 2 pieces
loose fitting. Be careful when removing the trim
ring that the glass lens does not fall out.
•
•
Grasp the bulb and pull it straight out from the
lamp socket.
Replace with 120 volt, 40 watt halogen bulbs with
a G9 base SUITABLE FOR USE IN OPEN
LUMINAIRES.
Follow package directions, wear gloves, do not
touch bulb with your bare fingers.
Bulb
ease Filters
To Replace The Metal Gr
Grease
Reverse procedure.
To Clean Filters
least once a month; they can be washed by hand
or in the dishwasher.
dry thoroughly before replacing it.
•
Replace inner cover by
inserting the three
retaining tabs into the
three slots and pressing
them firmly in place.
NOTE: Once you have replaced the light bulb,
make sure to put back the glass in its place.
19
Care and cleaning
Optional Charcoal Filters
If the model is not vented to the outside, the air will be recirculated through disposable charcoal
filters that help remove smoke and odors.
The charcoal filters cannot be cleaned.
They must be replaced.
The charcoal filters are clipped inside of each metal grease filter (mounting instructions included with
charcoal filter kit).
The charcoal filters should be replaced every 4-6 months (depending on hood usage).
NOTE: DO NOT rinse, or put charcoal filters in an automatic dishwasher.
NOTE: Charcoal filters are not included with the hood.
They must be ordered from your supplier.
Order the needed kit specifying your hood model and width size.
Charcoal filter placement (Recirculating accessories)
Fit the charcoal filter mattress on the upper side of each grease filter.
Use provided springs to fix it in place.
NOTE: When removing for replacing for a new one do not remove Fixing Springs, simply pull out and
rotate outwards.
Cleaning
• Always use the mildest cleaner that will do the
job. Use clean, soft cloths, sponges or paper
towels.
•
grain. Wipe area dry to avoid water marks.
• After cleaning, place all parts in their proper
positions before using.
The cleaners recommended below indicate a type
and do not constitute an endorsement. Use all
products according to package directions.
Hood Surface
Painted Surfaces: For general care, wipe the outside
of the hood with sudsy water or household cleaners
such as Fantastic® or Formula 409®, rinse well and dry
with a clean soft cloth to avoid water marks.
Stainless Steel Surfaces: Wipe and dry stainless
steel in the same direction as the grain. Avoid using
too much pressure, which may mar the surface. To
cleaners such as Stainless Steel Magic. Do not allow
any cleaning compounds to remain in contact with
stainless steel for extended periods.
Plastic surfaces: Wipe with a moist soapy sponge.
Rinse and dry.
Aluminum Mesh Filters:
washer or by agitating in sudsy water. Ensure that
Anodized Aluminum surfaces: Top cap is not removable. Wash top and underside with hot sudsy water.
Rinse and wipe dry or apply Fantastic® or Formula
409®
wipe clean. DO NOT USE powdered cleaners or
steel wool pads.
20
Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay
all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such
appliance is installed, used and maintained in accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA
or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory.
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
doors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER’S SOLE AND
EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO
ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS
WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR
LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers
below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts
under this warranty must be performed by Electrolux or an authorized service company. Product features or speci cations as
described or illustrated are subject to change without notice.
USA
1.800.944.9044
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
LI287D
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement