Messages on the LCD screen will guide you through the operations

Messages on the LCD screen will guide you through the operations
ACCESS CODES
To program Access Codes:
1) Press
The installer must enable each One-touch Button.
2) Enter your [MASTER
CODE]
3) Enter three-digit section
(see Table)
4) Enter new 4- or 6-digit [CODE]
5) Press
to exit
Section:
Codes:
[001]
[002]
[003]
[004] to [047]
[048]
System Master Code
Master Code 1
Master Code 2
User codes 004 to 047
Duress or User code 048
To Regular Arm: Press
To Stay Arm:
Press
To Force Arm:
Press
To Bypass:
Press
FAST EXIT
When the system is already Stay
Armed, press and hold the button for
3 seconds to start the Exit Delay.
Press & hold:
To delete Access Codes:
: Stay Armed after Exit Delay
1) Repeat steps 1 to 3
: Force Armed after Exit Delay
2) Press
3) Press
User’s Quick
Reference Guide
ONE-TOUCH BUTTONS
Press & hold a button for 3 seconds
without entering your Access Code.
for each digit in the code
to exit
: Regular Armed after Exit Delay
ON
OFF
AC LIGHT
= AC power
= Power failure
Messages on the LCD
screen will guide you
through the operations
STATUS LIGHT
Green:
Use arrow buttons to
ON
= Zones closed
scroll menu or choices
OFF
= Zone(s) open
FLASH = Exit Delay
Red:
ON
= System armed
FLASH = Stay Armed
FAST FLASH = Alarm
1641
ARMING AND DISARMING
To arm
To arm
when leaving:
when staying:
To Stay Arm
To Regular Arm
(Arms Area’s perimeter)
(Arms entire Area)
Enter your [ACCESS CODE]*
One-touch Button,
+ Enter your [ACCESS
?if enabled:
One-touch Button,
PRINTED IN CANADA 02/00 1641EQ-00
?if enabled:
To Instant Arm
(Arms Area without waiting for all
zones to close)
(Stay Arms Area, but if any armed zones are
breached, it will instantly cause an alarm)
+ Enter your [ACCESS
?if enabled:
CODE]
*
Stay Arm + press
for 3 seconds
during the exit delay.
To Disarm: enter your [ACCESS
Security Company:
*
To Force Arm
One-touch Button,
Web site: www.paradox.ca
CODE]
CODE]
* If needed, press button(s) corresponding to desired partition(s).
FNC1 BUTTON
Your system may have one or more
home automation options. One of
these options may be triggered
directly from the keypad (i.e. reset
smoke detector, activate lights, etc).
Press
for 3 seconds to activate.
KEYPAD SETTINGS
You can modify the keypad’s settings
to suit your needs.
ALARM MEMORY DISPLAY
To view the alarms that occurred last
armed period.
1) Press & hold
1) Press
Use the arrow buttons to view
the zones that were breached
during the last armed period.
for 3 seconds
2) Choose one. Press:
Backlight: keypad’s light
(7 is brightest)
BYPASS PROGRAMMING
Bypassed zones remain unarmed
when the area is armed.
One-touch Button,
Contrast: character intensity
(7 is lightest)
Scroll Speed: time between
messages (7 is slowest)
?if enabled:
1) Press
3) Press
2) Enter [ACCESS CODE]
If needed, press button(s) to
choose partition(s).
4) Press
3) Enter the zone number
or scroll the list and press
when the desired zone
appears on the screen.
OR
Press
for Bypass Recall
To re-bypass the zones bypassed
during last armed period.
4) Press
to exit
or
to modify
to save
2) Press
to exit
TROUBLE LIST
No or Low Battery
Wireless Transmitter Battery Low
Power Failure
Bell/PGM2 Disconnected
Bell Current Failure
Auxiliary Current Failure
Made a mistake?
Press
To erase entry or revert to last step
Communication Failure
Timer Loss
5) Return to step 2 or
to exit
CHIME PROGRAMMING
Keypad beeps when the zone opens.
1) Press
for 3 seconds
2) Enter the zone number
or scroll the list and press
when the desired zone
appears on the screen.
3) Press
Press
TROUBLE DISPLAY
When a trouble condition occurs,
“System Trouble [TRBL] to view” will
appear on the screen.
Tamper/Zone Wiring Failure
Press
to view which zone(s)
Telephone Line Monitoring Failure
1) Press
Fire Zone Trouble
2) Use
or
to view the
occuring trouble(s) (see Trouble List).
Consult the User Manual or contact
your Security Company for repairs.
Module Loss
3) Press
Keypad Fault
to exit
In Step 3 of Bypass or Step 2 of Chime Programming, re-enter the zone number or press the button indicated to disable the feature.
and enter time (HH:MM)
to exit
Wireless Transmitter Supervision Loss
Press
to view which zone(s)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement