Hot Spot Wireless Subscriber Gateway

Hot Spot Wireless Subscriber Gateway
Hot Spot
Wireless Subscriber Gateway
WSG-401
User’s Manual
Copyright
Copyright (C) 2004 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET
Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s
Manual and all accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any
electronic medium or machine-readable form by any means by electronic or mechanical. Including
photocopying, recording, or information storage and retrieval systems, for any purpose other than the
purchaser's personal use, and without the prior express written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and
applications, and makes no warranty and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims
liability for any inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a
commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may
be contained in this User’s Manual. PLANET makes no commitment to update or keep current the
information in this User’s Manual, and reserves the right to make improvements to this User’s Manual
and/or to the products described in this User’s Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate
your comments and suggestions.
CE mark Warning
The is a class B device, In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous
hardware and software products by their trade names. In most, if not all cases, these designations are
claimed as trademarks or registered trademarks by their respective companies.
Revision
User’s Manual for PLANET Hot Spot WSG-401:
Model: WSG-401
Rev: 1.0 (Dec. 2003)
Part No. EM-WSG401V1
2
WSG-401 User Manual
Table of Contents
1. Introduction .....................................................................................................................................4
1.1 Package Contents..................................................................................................................4
1.2 Features.................................................................................................................................4
1.3 WSG-401 Outlook ..................................................................................................................6
1.4 Technical Specifications .........................................................................................................8
2. Installation.....................................................................................................................................12
2-1 Wall-Mounting ......................................................................................................................12
2.2 Connecting the Antennas .....................................................................................................12
2.3 Installation Requirements .....................................................................................................13
2-4 Getting Start.........................................................................................................................14
3. Configuring the WSG-401 .............................................................................................................16
3-1 Setting Wizard......................................................................................................................16
3-2 Advanced Setup...................................................................................................................38
3-3 System Status.................................................................................................................... 116
3-4 System Tools......................................................................................................................122
Appendix A RJ-45 Connector Description........................................................................................131
WSG-401 User Manual
3
1. Introduction
Inheriting the convenience of Plug-n-Play Internet access, the PLANET WSG-401 is the ideal solution
for establishing Hot Spot Internet service applications. Via built-in billing mechanism and integrated with
receipt printing capabilities makes the PLANET WSG-401 suitable for providing Internet access of
businesses and public areas applications, such as hotel, cyber café, train stations, school libraries and
airports.
The PLANET WSG-401 comprises 802.11b+, wireless access point, interface, a 4-port auto-sensing,
auto-MDI/MDI-X 10/100Mbps switch, and a standard 10/100Base-TX WAN port providing superior
Internet access for wired, and wireless subscribers. Internet subscriber gateway WSG-401 combines
all the functionalities in a single, tiny box, WSG-401 can work independently, no enormous RADIUS
system integration, and no much computer expertise required, this benefit customer to deploy their Hot
Spot business faster and easier than ever. WSG-ACG, a compact thermal printer allowing machine
operators, clerks and cashiers to print out billing information.
1.1 Package Contents
Please inspect your package. The following items should be included:
l One WSG-401
l Two antennas
l One AC Power Adapter for WSG-401
l One CD containing User’s Manual
l One Quick Installation Guide
l Two screws for wall-mount
l One UTP Ethernet/Fast Ethernet cable (Cat.5 Twisted-pair)
If any of the above items are damaged or missing, please contact your dealer immediately.
1.2 Features
l Ideal Hot Spot solution
Via the integrated 802.11b wireless interface, mobile users can establish high speed Internet
access without any configuration.
l Zero configuration (Plug-n-Play) Internet access
WSG-401 translates proper IP address information for Internet access, all IP configurations,
DHCP, Private IP or Static IP information will be turned into Internet-ready configurations.
Subscribers won't feel the difference, and no need to face to the inconvenience of IP
reconfigurations.
l Built-in proprietary AAA mechanism and billing system
PLANET WSG-401 integrates Web-based Authentication (including subscriber SSL logon page),
4
WSG-401 User Manual
selective Web-based Accounting, and proprietary billing mechanism, which can help you
prepare a billing mechanism in a very short time, and billing system in WSG-401 works without
RADIUS system, and bring most convenience, the least efforts for billing applications.
l Exclusive Printer Accounting
Machine operators may customize the printout information for different billing application.
l Security and Firewall
With built-in 64/128/256-bit RC4 WEP Encryption, VLAN Security for Wireless, subscriber SSL
Login Page / Admin Page, VPN (IPSec/PPTP) Pass through.....various security features,
PLANET WSG-401 bring you an ease-f-use and most comfort safe Internet access environment.
l Ease-of-Use and Management
The built-in web management interface in WSG-401 brings most convenience to system
administrators or machine operators while configuring machine or setting up subscriber
privileges in movements. With time increments, clerks or machine operators may print out, billing
and other user information with time increments are conveniently printed on the button-operated
printer included with the PLANET WSG-401. Time increments may be compiled simply by
pressing the printer button multiple times. No computers or complex back-end subscriber
management systems are required for deployment.
Note: The "PnP" Function only can be used with TCP/IP-based Network.
WSG-401 User Manual
5
1.3 WSG-401 Outlook
Figure 1-1 WSG-401 Outlook
1-3-1 Top Panel
The top panel of the WSG-401 is shown below.
Figure 1-2 WSG-401 Top Panel
6
WSG-401 User Manual
LEDs Indication
LED
State
Description
Power
Off
WSG-401 is not receiving electrical power.
Green
WSG-401 is receiving electrical power.
Green
The WAN port is used to connect your xDSL or Cable modem.
WAN
Green (Blinking) Data is in transmitting and receiving on WAN port.
LAN (1-4)
Green
A port has established a valid 10/100Mbps network connection.
Green (Blinking) 10/100Mbps traffic is traversing the port.
Wireless
Off
Port has not established any network connection.
Green
The WSG-401 has established a valid wireless connection.
Green (Blinking) The Wireless connection is active.
Status
Off
The WSG-401 status is defective.
Green (Solid)
WSG-401 status is complete.
Green (Blinking) During firmware upgrades, this status LED will blink.
1-3-2 Rear Panel
Rear panel of PLANET WSG-401 is shown below.
Figure 1-3 WSG-401 Rear Panel
1. Power Jack:
Used to connect the external power supply with PLANET WSG-401 device.
2. LAN Port:
WSG-401 supports four auto-sensing RJ-45 ports and all ports can be auto-switched to MDI-II
connections. The LAN ports used for linking hosts or other networking device.
3. WAN Port:
One RJ-45 port used for linking xDSL or Cable Mode
4. Device Port
Used to connect the Thermal Printer WSG-ACG.
1-3-3 Left Side Panel
The left side panel of the WSG-401 is shown below.
WSG-401 User Manual
7
1. Reset Button:
WSG-401 integrates a reset button at the left side panel of the device. Under some circumstances you
might need to reset the device.
Figure 1-4 WSG-401 Left Side Panel
1.4 Technical Specifications
1-4-1 Hardware Specifications
Network Specification
IEE802.3 10BaseT Ethernet
IEE802.3u 100BaseTX Fast Ethernet
IEE802.11b Wireless LAN
ANSI/IEEE 802.3 NWay auto-negotiation
Wi-Fi Compatible
Connectors
Four LAN Ports (10BaseT/100BaseTX Auto cross-over)
One WAN Port (10BaseT/100BaseT)
One Device Port (1 DB25 male RS232 for external device application)
Wireless Operation Range
Open Space: 100~300m
Indoors: 35~100m
Wireless Data Rate
22 Mbps, 11 Mbps, 5.5 Mbps, 2 Mbps, 1 Mbps
Encryption
64/128/256-bit RC4
8
WSG-401 User Manual
External Antenna Type
2dBi (Max) Dual detachable diversity antenna with reverse SMA
Power Requirement
External Power Adapter
Input: 100-240 VAC, 50/60 Hz
Output: 5V, min 1.4A
LED Indicators
One POWER LED
One WAN Link/Activity LED
Four LAN Link/Activity LEDs
One Wireless Link/Activity LED
One Status LED
Dimension
Size: 200(L) x 130(W) x 44(H) mm
Weight: About 400g (Net)
WSG-401 User Manual
9
Environment Conditions
Operating Temperature: 0 to 50°C
Operating Humidity: 10~90% non-condensing
Certifications
FCC part 15 Class B, CE, Class B, UL,
CE , C-Tick
Mounting
Desktop, Wall mounted
1-4-2 Software Specifications
Networking
•
IEEE802.3 10BaseT Ethernet
•
IEEE802.3u 100BaseTX Fast Ethernet
•
Supports 100 Simultaneous Users
•
IP Plug and Play (iPnP)
•
HTTP Proxy Support
•
WEP Data Encryption
•
SMTP Server Redirection
•
DHCP Server
•
DHCP Relay
•
Static IP WAN Client
•
DHCP WAN Client
•
PPPoE WAN Client
•
PPTP WAN Client
•
NAT
•
IP Routing
•
NTP (Network Time Protocol) Support
•
IP Multicast support
Marketing Cooperation
•
Advertisement URL link
•
Walled garden
•
Customize Login Page
•
Portal Page
10
WSG-401 User Manual
AAA / Billing
•
Built-in Authentication
•
Web-based Login Page Authentication
•
Exclusive Printer Accounting without PC operating
•
Web-based Accounting
•
Flexible Billing Profiles and Price Plan
•
Flexible Billing Mechanism (Pre-Paid and Post-Paid)
•
Flexible Time Mechanism (Time to Finish and Accumulation)
•
Credit Card Support (Authorize.net and iTable)
•
External PS/2 Keypad Support
Security
•
Layer 2 Isolation
•
SSL Login Page
•
SSL Administration
•
VPN Pass through (IPSec/PPTP/L2TP)
•
Customize SSL Certificate
•
Pass through Destination IP/URL
•
Pass through Source IP/MAC
•
Restricted Destination Filtering IP/URL
•
Share LAN Resources
Management
•
Administrator/Super Subscriber/Account Manager Management Access
•
Remote Browser-based Configuration and management
•
Authorized remote management (Access Control List)
•
Firmware Upgrade via HTTP/TFTP
•
Scheduled Firmware Upgrade
•
Backup/Restore/Factory Default Setting
•
LAN Device Management
•
Dynamic DNS
•
System Information Table
•
Real-time Current User List / DHCP Clients List / Session List / Account List
•
Syslog
•
Status Report (Daily/Monthly/System/Network)
WSG-401 User Manual
11
2. Installation
Following sessions are physical installation steps of WSG-401. Please refer to the illustration and follow
the steps below to complete the installation of your device.
2.1
Wall-Mounting
The WSG-401 can be wall-mounted on a wall by applying the two mounting brackets on screws.
Figure 2-1 Wall-Mounting Bracket - Bottom of WSG-401
Please refer to the following instructions for mounting a WSG-401 on a wall or other surface.
1.
Install two screws on a wall according to the relative positions shown below.
Figure 2-2
2. Hang WSG-401 on the wall by sliding the two screws in the mounting brackets.
Note: If the screws are not properly anchored, the strain of the cables connected to the WSG-401 rear
panel connectors could pull out the WSG-401 from the wall.
2.2 Connecting the Antennas
PLANET WSG-401 provides two antenna connectors on the rear of the unit for wireless subscribers.
12
WSG-401 User Manual
2.3 Installation Requirements
Before installing the WSG-401, make sure your network meets the following requirements.
System Requirements
The WSG-401 requires one of the following types of software:
l Windows 98 Second Edition/NT/2000/XP
l Red Hat Linux 7.3 or later version
l MAC OS X 10.2.4 or later version
l Any TCP/IP-enabled systems like Mac OS and UNIX (TCP/IP protocol installed)
l Standard phone line for xDSL modem
Or Coaxial cable for Cable modem
l Web Browser Software (Microsoft I.E 5.0 or later version or Netscape Navigator 5.0 or later
version)
l One computer with an installed 10Mbps, 100Mbps or 10/100Mbps Ethernet card
l UTP network Cable with a RJ-45 connection (Package contents)
Note: Prepare twisted-pair cables with RJ-45 plugs. Use Cat.5 cable for all connections. Make sure
each cable not exceed 328 feet (Approximately 100 meters).
ISP Requirements
Verify whether your ISP use fixed or dynamic IP. If it is a fixed IP, be sure to get the IP from your ISP.
For dynamic IP, which is mostly used, the PC will get the IP automatically whenever it hooks up on
the modem.
Dynamic IP
l Dynamic IP Setting
WSG-401 User Manual
13
Fixed IP
l Your fixed IP address for the WSG-401
l Your subnet mask for the WSG-401
l Your default gateway IP address
l Your DNS IP address
PPPoE
l Your user name from your ISP
l Your password from your ISP
PPTP
l PPTP Server IP Address from your ISP
l PPTP Local IP address from your ISP.
l PPTP Local IP subnet mask from your ISP.
l Your user name from your ISP
l Your password from your ISP
Your PC Requirements
The Static IP settings for the PC
l Your PC’s fixed IP address
l Your PC’s subnet mask
l Your PC’s default gateway IP address
l Your PC’s primary DNS IP address
Note:
1. The gateway’s default IP address setting is “192.168.0.1”.
2. The gateway’s default subnet mask setting is “255.0.0.0”.
The Dynamic IP settings for the PC
We recommend that you leave your IP settings as automatically assigned. By default, WSG-401 is a
DHCP server, and it will give your PC the necessary IP settings.
2.4
Getting Start
1. Place the WSG-401 and Mini account generator printer on a flat work surface.
2. Connect the DB25 connector of printer cable into the device port on the rear of the WSG-401.
3. Plug the other end of the printer cable into the RJ11 port of the mini account generator printer. Check
that the account generator printer status LED lights.
4. Ensure that your modem and computer are both switched on.
5. Use the supplied cable to connect the WSG-401's WAN port to the modem. Check that the
Cable/xDSL Status LED lights.
6. Connect your computer to one of the 10/100 LAN ports on the WSG-401. Check that the LAN Port
14
WSG-401 User Manual
Status LED lights.
7. Configure the further parameters via a web browser.
Figure 2-1 WSG-401 Connection
WSG-401 User Manual
15
3. Configuring the WSG-401
3.1
Setting Wizard
Step 1: Start your browser, and then enter the factory default IP address 192.168.0.1 in your browser’s
location box. Press Enter.
Step 2: The WSG-401 configuration tools menu will appear. In the Username and Password field, type
the factory default user name (admin) and password (password) and click “Getting
Started”. If you are first time setting the system, the wizard setup screen will appear. You will
be guided, step-by-step, through a basic setup procedure.
Username: admin
Password: password
Figure 3-1 Configuration Tools Menu
16
WSG-401 User Manual
Note:
F If you would like to change the password please see Step 10.
F Username and Password can consist of up to 20 alphanumeric characters and are case sensitive.
F If for some reason your password is lost or you cannot gain access to the WSG-401 Configuration
Program, please press the reset button to load the device to manufacturer defaults.
F If the WSG-401 doesn’t send packet in 5 minutes (default), the WSG-401 wills logout automatically.
F Proxy needs to set disable first when administrator accesses admin UI.
Step 3: Internet Connection Setting
Select the appropriate Internet connection type to connect to your ISP.
l DHCP Client
Figure 3-2 Internet Connection Setting Screen—DHCP Client Setting
The device can work as a DHCP client. This allows the device to obtain the IP address and other
TCP/IP settings from your ISP. If your xDSL/Cable comes with this feature, please enable Use DHCP
Client.
WSG-401 User Manual
17
l Static IP Setting
If “Static IP” is selected, then this screen will appear. Enter the IP address information provided by your
ISP.
Figure 3-3 Internet Connection Setting Screen—Static IP Setting
Item
IP Address
Default
0.0.0.0
Description
Enter the IP address provided by your ISP.
Subnet Mask
0.0.0.0
Enter the subnet mask provided by your ISP.
Gateway IP
0.0.0.0
Enter the Gateway IP Address provided by your ISP.
Empty
Enter the primary DNS server IP address for the xDSL/Cable
Address
Primary DNS
Server
Secondary DNS
Server
connection (provided by your ISP).
Empty
Enter the secondary DNS server IP address for the xDSL/Cable
connection (provided by your ISP). If the primary DNS Server IP were
not available, meanwhile, Secondary DNS Server IP would start in the
same time.
18
WSG-401 User Manual
l PPPoE (Point-to-Point Protocol over Ethernet)
If “PPPoE” is selected, then this screen will appear. Enter the username, password and other major
fields.
Figure 3-4 Internet Connection Setting Screen—PPPoE Setting
Item
Default
Description
Enter the user name provided by your ISP. The user name
Username
Empty
can consist of up to 80 alphanumeric characters and is
case sensitive.
Enter the user password provided by your ISP. The
Password
Empty
password can consist of up to 80 alphanumeric
characters and is case sensitive.
PPP MTU Setting
1492
MTU (Maximum Transfer Unit) specifies maximum
transmission unit size.
TCP MSS Setting
1452
MSS (Maximum Segment Size) specifies maximum
segment size.
Service name
WSG-401 User Manual
Empty
Your ISP will provide the service name.
19
Item
Default
Description
Connect on Demand and Max Idle Time
Connect on Demand Enable
You can configure your WSG-401 to cut your connection
with your ISP after a specified period of time (Max Idle
Time). If you have been disconnected due to inactivity,
Connect
on
Demand
enables
your
WSG-401 to
automatically re-establish your connection as soon as you
Max Idle Time
10 Minutes attempt to access the Internet again. If you wish to
activate Connect on Demand, click the check box. If you
want your Internet connection to remain, click the check
box of keep alive. The Max Idle Time maximum value is
65535 minutes.
Keep alive and Redial Period
Keep alive
Disable
This option keeps your PPPoE enabled Internet access
Redial Period
30 Seconds connected indefinitely, even when it sits idle. The Redial
Period maximum value is 65535 seconds.
20
WSG-401 User Manual
l PPTP Client (Point-to-Point Tunneling Protocol)
If “PPTP” is selected, then this screen will appear. Fill out all the information provided by your ISP.
Figure 3-5 Internet Connection Setting Screen—PPTP Client Setting
Item
Default
My IP Address
Empty
My Subnet Mask
Empty
Gateway IP Address
Empty
PPTP Server IP
Address
WSG-401 User Manual
Empty
Description
Enter the PPTP local IP address provided by your ISP.
Enter the PPTP local Subnet Mask IP address provided
by your ISP.
Enter the PPTP server Gateway IP address provided by
your ISP.
Enter the PPTP server IP address provided by your ISP.
21
Item
Default
Description
Enter the user name provided by your ISP. The user name
Username
Empty
can consist of up to 80 alphanumeric characters and is
case sensitive.
Password
Empty
Enter the user password provided by your ISP. The
password can consist of up to 80 alphanumeric
characters and is case sensitive.
Connection ID/Name Empty
PPP MTU Setting
1460
TCP MSS Setting
1400
Enter the Connection ID or Connection Name.
MTU (Maximum Transfer Unit) specifies maximum
transmission unit size.
MSS (Maximum Segment Size) specifies maximum
segment size.
Connect on Demand and Max Idle Time
Connect on Demand Enable
You can configure your WSG-401 to cut your connection
with your ISP after a specified period of time (Max Idle
Time). If you have been disconnected due to inactivity,
Connect
on
Demand
enables
your
WSG-401 to
automatically re-establish your connection as soon as you
Max Idle Time
10 Minutes attempt to access the Internet again. If you wish to
activate Connect on Demand, click the check box. If you
want your Internet connection to remain, click the check
box of keep alive. The Max Idle Time maximum value is
65535 minutes.
Keep alive and Redial Period
This option keeps your PPTP enabled Internet access
Keep alive
Disable
connected indefinitely, even when it sits idle. The Redial
Period maximum value is 65535 seconds.
22
WSG-401 User Manual
Step 4: Wireless Setting
This page allows you to define ESSID, Channel ID and WEP encryption for wireless connection.
Figure 3-6 Wireless Setting Screen
Item
ESSID
Default
Wireless
Description
The ESSID is the unique name that is shared among all points
in a wireless network. It is case sensitive and must not exceed
32 characters.
Channel
6
WEP Encryption Disable
Enter the channel ID for wireless connection.
Disables or set the use of the WEP algorithm. Enabling the
security can protect your data while it is transferred from one
station to another. The WSG-401 supports 64-bit, 128 bit or
256 bit WEP encryption.
Enter 5 characters for ASCII 64-bit WEP Key.
Enter 13 characters for ASCII 128-bit WEP Key.
Enter 29 characters for ASCII 256-bit WEP Key.
WSG-401 User Manual
23
Step 5: E-mail Server Setting
WSG-401 allows an extra Email server parameter to forward the subscriber’s E-mail.
Figure 3-7 E-mail Service Setting Screen
Item
Default Description
Email Server Redirect
No
Disables or enables email server redirect function. To
prevent some subscriber’s original Email server may
protect by firewall or NAT network. WSG-401 provides an
extra Email server parameter to forward the subscriber’s
Email. The WSG-401 not only forwards the subscribers’
E-mail via other E-mail server but also changes the
SMTP header. The recipient of your E-mail sees the
message as if you sent it from your local Internet Service
Provide, not form the hotel or other place.
Email Server IP address Empty
Before setting this field, please make sure the E-mail
or Domain name
sever relay function is opened. It must not exceed 50
characters.
SMTP Port
25
Enter the SMTP port. The SMTP port allowed range is 25
or 2500 to 2599.
24
WSG-401 User Manual
Step 6: Authentication Service Setting
Figure 3-8 Authentication Service Setting Screen
Item
Default
Description
Built-in Authentication/
No,
No Authentication
No Authentication Subscriber can direct access the Internet without
No―
entering username and password.
Yes―
WSG-401
provides “Built-in
Authentication”
for
service provider to build up an Internet service
without any extra authentication software. If “Built-in
Authentication” is selected, service provider can
generate the subscriber account inside WSG-401,
and the system will authenticate the subscriber login
according to the generated account.
WSG-401 User Manual
25
Step 7: Billing Profile Setting
The function is used to setup a billing profile. A billing profile is a description of how you want to charge
your customer.
Figure 3-9 Billing Profile Setting Screen
Description
Item
Default
Service
Time to Finish Options: “Time to Finish” or “Accumulation”.
Time to Finish―
The subscriber can access Internet only one time with one account.
Once subscriber login, the pre-defined usage time will start until run
out even the subscriber stop to access the Internet before run out.
26
WSG-401 User Manual
Accumulation―
The subscriber can access Internet many times with one account.
The system can keep and accumulate every single usage time until
the pre-defined usage time run out.
Item
Default
Description
Currency
$
Enter the appropriate currency unit or currency symbol.
Number of
2
The field maximum value is 3.
01~03
The index number of billing profile. In Wizard setup, we provide
decimals
places
No
only 3 billing profile.
Name
30 minutes/
It is the name of billing profile. The maximum allowed characters
1 hour/
length is 12.
2 hours
Usage Time
30 minutes/
The duration of the billing period. When this period expires, user
1 hour/
account will be discontinued.
2 hours
Charge
1.00/2.00/3.00 Enter the amount of Internet service. The amount maximum value
is 999999.
Step 8: Account Generator Printer Setting
There are two different choices, one is exclusive printer (Account Generator Printer), and the other is
non-exclusive printer. Exclusive printer is a portable thermal printer that is integrated with WSG-401 to
press button to generate accounts and receipt immediately without PC operating. Non-exclusive printer
can use the PC Web-based browser to print out user account.
WSG-401 User Manual
27
Figure 3-10 Printer Setting
Button B
Button A
Button C
Figure 3-11 Account Generator WSG-ACG
28
WSG-401 User Manual
Step 9: Account Generator Setting
Nam
Charg
N
Usage
Figure 3-12
Item
Button A~ C
Default
01
Description
Define each button’s billing profile. Select one billing profile by
clicking in the list box.
Printout
Number of copies to print 1
The system allows you to print all your bills. This value is
number of copies.
This function allows you to produce custom bill based on your
requirements.
Click “I want to setup the web-based accounting now if exclusive printer cannot work” to open the
“Web-based Account Generator Setting” screen to start the web-based accounting function.
WSG-401 User Manual
29
l Web-based Account Generator Setting
Figure 3-13 Web-based Account Generator Setting Screen
Description
Item
Default
Billing Profile (Button
Define each button’s billing profile. Select one billing profile by clicking
A~C)
in the list box.
Printout
Number of copies to
1
print
The system allows you to print all your bills. This value is
number of copies.
-
This function allows you to produce custom bill based on
your requirements.
Web-based Account
Username
account
Enter the user name for web-based account generator.
The user name can consist of up to 80 alphanumeric
characters and is case sensitive.
30
WSG-401 User Manual
Password
account
Enter the password for web-based account generator.
The password can consist of up to 80 alphanumeric
characters and is case sensitive.
Confirm
Empty
Enter the password for confirmation.
Click on button to preview and operate account generator panel.
Button A
Button B
Button C
Figure 3-14 Account Generator Panel
Click on button to add a new account.
WSG-401 User Manual
31
Figure 3-15 Example-Account Printout
32
WSG-401 User Manual
Click “View Account List” to display current account information.
Figure 3-16 Account List
Click on refresh button to update the account list page.
The field name button in this list show that this list can be sorted in ascending/descending order
according to the corresponding field name.
Select the check boxes and click ‘Delete’ to delete accounts.
Delete all accounts in account list.
Note: This page will refresh automatically every 5 minutes.
If you would like to leave the account generator panel, please click Logout to exit.
WSG-401 User Manual
33
Customize Printout Text
This function allows you to produce custom bill based on your requirements.
Figure 3-17 Customize Printout Text Setting Screen
Click the button to displays the account on the screen as it would appear when printed.
34
WSG-401 User Manual
Figure 3-18 Example- PC-connected printer Printout
Figure 3-19 Example- Account Generator Printer Printout
WSG-401 User Manual
35
Figure 3-20 Example-Post-paid Printout
36
WSG-401 User Manual
Step 10: System Setting
Figure 3-21 System Setting Screen
Item
Default
Description
Username
admin
Enter the user name. The user name can consist of up to
Password
password
80 alphanumeric characters and is case sensitive.
Enter the user password. The password can consist of up
to 80 alphanumeric characters and is case sensitive.
Confirm
Empty
System date and
YYYY/MM/DD
time
HH:MM:SS
Enter the password of administrator for confirmation.
Click “Get from my Computer” button to correct the
system date and time.
Secure
All
This function allows remote user to management the
Administrator IP
device. You can specify one or any IP addresses for
Address
remote control the system.
Click the button to save the settings then the system will restart.
WSG-401 User Manual
37
3.2
Advanced Setup
The Advanced Setting enables you to configure advanced settings related to accessing the Internet,
including,
1.
System
2.
WAN/LAN
3.
Server
4.
Authentication
5.
Billing
6.
Accounting
7.
Credit Card
8.
Keypad
9.
Customization
10. Pass Through
11. Filtering
12. Share
13. Portal Page
14. Advertisement
15. Walled Garden
16. DDNS
17. LAN Devices
18. Syslog
19. Wireless
Figure 3-22 Advanced Setting Item Screen
Note: After change the settings of device, please click apply button to save the new settings.
38
WSG-401 User Manual
3-2-1 System
Define the WSG-401 System configuration.
Figure 3-23 System Setting Screen
WSG-401 User Manual
39
Item
Default
Description
The system name can consist of up to 40
System/Host Name
Empty
Domain Name
Empty
Location Information
Empty
Enter your location information.
System
The system date of the WSG-401. The valid setting of
Date
year is from 2002 to 2035.
alphanumeric characters.
The Domain name can consist of up to 80
alphanumeric characters.
Date/Time
Date (Year/Month/Day)
Time (Hour:Minute:Second)
System
Time
-
-
The system time of the WSG-401.
Click “Get from my Computer” button to correct the
system date and time.
Click “Get from NTP server” button to correct the
system date and time.
Enables or disables NTP (Network Time Protocol)
Time Server. Network Time Protocol can be utilized to
NTP Setting
Disable
synchronize the time on devices across a network. A
NTP Time Server is utilized to obtain the correct time
from a time source and adjust the local time.
Server IP/Domain Name
Empty
Time Zone
GMT-12:00 Select the appropriate time zone for your location.
Update Time
0 hours
Disable
Daylight Saving Time
Month/Day
Enter the IP address/domain name of NTP server.
Enter the number of hours for update time.
Enables or disables Daylight Saving Time (DST).
Set the Daylight Saving Time (DST) on the WSG-401.
Adjust the begin time and end time.
NAT (Network Address Translation)
NAT
Enable
Enables or
disables
NAT Address Translation
function.
Enables or disables plug & play Internet function.
Plug and Play Internet access Enable
When enabled, the user needn’t change their network
configuration to access the Internet.
40
WSG-401 User Manual
Item
Default
Description
While Internet servers on your LAN such as proxy
server and SMTP server require IP addresses, it is
often not necessary to assign real IP addresses to
DNS Fake IP Reply
Enable
each end-user workstation on a LAN. NAT is the
process of assigning fake IP addresses to network
devices, then translating them into a real IP address
for Internet communication.
If plug and play Internet access is selected, you can
Layer 2 Isolation Security
Enable
enable Layer 2 Isolation Security function. When the
“Layer 2 Isolation Security” enabled, everyone cannot
communicate with each other.
Secure administrator IP
Addresses
Multicast Pass Through
Options: Any and Specify. User can specify 5 IP
Any
addresses or a range to allow remote control access
from network.
Disable
This function allows for multiple transmissions to
specific recipients at same time.
This function allows remote user to ping the
Allow remote user to ping the
device
Enable
WSG-401 through Internet. Ping is normally used to
test the physical connection between two devices, to
ensure that everything is working correctly.
Option: default or customize certificate, These are
two ways to create a certificate, one is purchase a
SSL Certificate
Default
certificate from a certificate authority (Ex. Verisign or
Thawte), and another is creating a self-certificate (For
example: Uses OpenSSL tool).
Click Apply button to save the new settings.
Click Apply button, then Restart dialog box will appear. Click Apply to restart the system.
Figure 3-24 Restart Dialog Box
WSG-401 User Manual
41
3-2-2 WAN/LAN
Figure 3-25 WAN/LAN Setting Screen
Click Apply button to save the new settings.
Click Apply button, then Restart dialog box will appear. Click Apply to restart the system.
Figure 3-26 Restart Dialog Box
l Device IP (LAN IP) Setting
Figure 3-27 Device IP (LAN IP) Setting
Item
IP Address
Default
192.168.0.1
Description
Internal LAN IP address of your WSG-401.
Subnet Mask 255.255.255.0 Subnet mask of your WSG-401.
42
WSG-401 User Manual
l WAN MAC Address
Figure 3-28 WAN MAC Address Setting
Item
Description
IP Address The default MAC address is set to the WAN physical interface on device.
l WAN Port Mode
Figure 3-29 WAN Port Mode Setting
DHCP Client
The device can work as a DHCP client. This allows the device to obtain the IP address and other
TCP/IP settings from your ISP. If your xDSL/Cable comes with this feature, please enable Use DHCP
Client.
Figure 3-30 DHCP Client Setting Screen
Static IP
Figure 3-31 Static IP Setting Screen
Item
IP Address
Description
Enter the IP address for the xDSL/Cable connection (provided by your
ISP).
Subnet Mask
WSG-401 User Manual
Enter the subnet mask provided by your ISP.
43
Item
Gateway IP Gateway
Description
Enter the Gateway IP address for the xDSL/Cable connection (provided by
your ISP).
Primary DNS Server
A primary DNS server IP address for the xDSL/Cable connection (provided
by your ISP).
Secondary DNS Server
A secondary DNS server IP address for the xDSL/Cable connection
(provided by your ISP). If the primary DNS Server IP were not available,
meanwhile, Secondary DNS Server IP would start in the same time.
PPPoE
Figure 3-32 PPPoE Setting Screen
Item
User Name
Default
Empty
Description
Enter your PPPoE account name. The user name can
consist of up to 80 alphanumeric characters and is case
sensitive.
Password
Empty
Enter your PPPoE password. The password can consist
of up to 80 alphanumeric characters and is case sensitive.
PPP MTU Setting
1492
TCP MSS Setting
1452
Service Name
Empty
MTU (Maximum Transfer Unit) specifies maximum
transmission unit size.
MSS (Maximum Segment Size) specifies maximum
segment size.
Your ISP will provide the service name.
(Option)
44
WSG-401 User Manual
Item
Default
Description
Connect on Demand and Max Idle Time
Connect on Demand Enable
You can configure your WSG-401 to cut your connection
Max Idle Time
with your ISP after a specified period of time (Max Idle
10 Minutes
Time). If you have been disconnected due to inactivity,
Connect
on
Demand
enables
your
WSG-401
to
automatically re-establish your connection as soon as you
attempt to access the Internet again. If you wish to
activate Connect on Demand, click the check box. If you
want your Internet connection to remain, click the check
box of keep alive. The Max Idle Time maximum value is
65535 minutes.
Keep alive and Redial Period
Keep alive
Disable
This option keeps your PPPoE enabled Internet access
Redial Period
30 Seconds connected indefinitely, even when it sits idle. The Redial
Period maximum value is 65535 seconds.
l PPTP
Figure 3-33 PPTP Setting Screen
WSG-401 User Manual
45
Item
Default
My IP Address
Empty
My Subnet Mask
Empty
Gateway IP Address
Empty
PPTP Server IP Address
Empty
Description
A PPTP local IP address for the xDSL/Cable
connection (provided by your ISP).
A PPTP local IP address for the xDSL/Cable
connection (provided by your ISP).
A PPTP local default gateway for the xDSL/Cable
connection (provided by your ISP).
A PPTP server IP address for the xDSL/Cable
connection (provided by your ISP).
Username
Empty
Enter your PPTP account name. The user name can
consist of up to 80 alphanumeric characters and is
case sensitive.
Password
Empty
Enter your PPTP password. The password can
consist of up to 80 alphanumeric characters and is
case sensitive.
PPP MTU Setting
1460
MTU (Maximum Transfer Unit) specifies maximum
transmission unit size.
TCP MSS Setting
1400
MSS (Maximum Segment Size) specifies maximum
segment size.
Connection ID/Name
Empty
Connection ID or connection name.
Connect on Demand and Max Idle Time
Connect on Demand
Enable
You can configure your WSG-401 to cut your
Max Idle Time
10 Minutes
connection with your ISP after a specified period of
time (Max Idle Time). If you have been disconnected
due to inactivity, Connect on Demand enables your
WSG-401
to
automatically
re-establish
your
connection as soon as you attempt to access the
Internet again. If you wish to activate Connect on
Demand, click the check box. If you want your
Internet connection to remain, click the check box of
keep alive. The Max Idle Time maximum value is
65535 minutes.
46
WSG-401 User Manual
Item
Default
Description
Keep alive and Redial Period
Keep alive
Disable
This option keeps your PPTP enabled Internet
access connected indefinitely, even when it sits idle.
Redial Period
30 Seconds The Redial Period maximum value is 65535
seconds.
3-2-3 Server
Figure 3-34 Server Setting Screen
Item
Default
Description
Web Server
Enter the Web server port number. The Web server port
Web Server Port
80
allowed range is 80 or 8010 to 8060. For access the
WSG-401
system
under
NAT,
please
tab
the
“http://WAN Port IP Address: Port Number”.
SSL Security
WSG-401 User Manual
Disable
Enables or disables the SSL security.
47
The idle time out valid range is 1-1440. If the idle time
Administrator Idle-Timeout 5 Minutes
out is set as 5 minutes, it means if the administrator
doesn’t send packet in 5 minutes, the administrator will
logout automatically.
Item
Default
Description
There are three types of DHCP Services.
DHCP Server
Enable
DHCP Disable—Disable the DHCP server function.
DHCP Relay—Enable DHCP Relay function.
DHCP Server—Enable DHCP server function.
To route DHCP through an external server, the administrator needs
DHCP Relay
to enable the DHCP relay and assign a valid DHCP server IP
address.
DHCP Server IP Address
DHCP Server
DHCP Pool Starting
Address
DHCP Pool Size
Lease Time
Empty
Enter the IP address of DHCP server.
The WSG-401's DHCP server is turned on and running by default
when you install it in your network.
192.168.0.2 Enter the DHCP Pool Starting IP address.
253
The DHCP pool size range is 1 to 512.
300
Enter the DHCP lease time. The DHCP lease time range
Minutes
is 1 to 71582788 minutes.
Primary DNS Server
168.95.1.1
Secondary DNS Server
Empty
Enter the IP address of the network’s primary DNS
server.
Enter the IP address of a second DNS server on the
network.
Email Server Redirect
To prevent some subscriber’s original Email server may protect by
firewall or NAT network. WSG-401 provides an extra Email server
parameter to forward the subscriber’s Email. The WSG-401 not only
forwards the subscribers’ E-mail via other E-mail server but also
changes the SMTP header. The recipient of your E-mail sees the
message as if you sent it from your local Internet Service Provide, not
form the hotel or other place. Note: Before setting this sever, please
make sure the e-mail sever relay function is opened. It must not
exceed 50 characters.
IP Address or Domain
Empty
Enter the E-mail server IP address or domain name.
25
Enter the SMTP port number for mail server. The SMTP
Name
SMTP Port
48
WSG-401 User Manual
port allowed range is 25 or 2500 to 2599.
Click Apply button to save the new settings.
WSG-401 User Manual
49
3-2-4 Authentication
Figure 3-35 Authentication Setting Screen
Item
Default
Authentication Type No
Authentication
Description
Option: No Authentication or Built-in Authentication.
No Authentication―
Subscriber can direct access the Internet without
enter username and password.
Built-in Authentication―
WSG-401
provides
“Built-in
Authentication”
for
service provider to build up an Internet service
without any extra authentication software. If “Built-in
Authentication” is selected, service provider can
generate the subscriber account inside WSG-401,
and the system will authenticate the subscriber login
according to the generated account.
Current User
1 Min(s)
Information Backup
The system provides automatically backup account
information and unused account to flash ROM. This
function allow administrator to adjust the backup
time. The default value is 1 minute. The Current User
Information Backup valid range is 1 to 1440.
SSL Login Page
Disable
Enables or disables SSL security of login page.
Click Apply button to save the new settings.
50
WSG-401 User Manual
3-2-5 Billing
The function is used to setup a billing profile. A billing profile is a description of how you want to charge
your customer.
Figure 3-36 Billing Setting Screen
WSG-401 User Manual
51
Item
Pre-Paid
Default
Enable
Description
The subscribers can access Internet with pre-defined
usage time.
If you change billing mode (Pre-paidàPost-paid or Post-paidàPre-paid), the system will erase all
account and disconnect all on-line users.
Figure 3-37 Message Box
Item
Default
Enable Credit Card Service Disable
Description
Enables or disables the credit card service. Before you
enable credit card service, make sure that your credit
service is configured to work. For details, see section
3-2-6 Credit Service.
Figure 3-38 Credit Service Setting Screen
52
WSG-401 User Manual
Figure 3-39 Error Dialog Box (Credit Card Service=Enable)
Item
Time to Finish
Default
Enable
Description
The subscriber can access Internet only one time with one
account. Once subscriber login, the pre-defined usage time will
start until run out even the subscriber stop to access the Internet
before run out.
Accumulation
Accumulation
Disable
The subscriber can access Internet many times with one
account. The system can keep and accumulate every single
usage time until the pre-defined usage time run out.
Idle Time Out
5 Min(s) The idle time out valid range is 1-1440. If the idle time out is set
as 5 minutes, it means if the account doesn’t send packet in 5
minutes, the account will logout automatically.
Accumulation
Time to Finish
login
login
A
logout
login
B
C
Time Bar
A
logout
login
logout
Usage time= A+B+C
Time Bar
finish
Usage time= A
Figure 3-40 Accumulation and Time to Finish
WSG-401 User Manual
53
Item
Post-Paid
Default
Disable
Description
The
subscribers
can
access
Internet
without
pre-defined usage time. This can be operated with an
optional external PS/2 keypad that is connected with
exclusive printer. The printout will only show the
username/password. An account can also to be
terminated with the optional keypad.
Note: Only three-button printer supports Post-paid
function.
Idle Time Out
5 Min(s) The idle time out valid range is 1-1440. If the idle time
out is set as 5 minutes, it means if the account doesn’t
send packet in 5 minutes, the account will logout
automatically.
Billing Profile
Currency
$
Enter the appropriate currency unit or currency
symbol.
Number of decimals places 2
Enter the number. The field maximum value is 3.
Tax Percentage
This check box is used to indicate the taxable status of
Disable
the account.
No.
5%
Enter the tax rate (i.e. a 5% sales tax is entered as 5).
+1~+10
The index number of billing profile. In Advanced setup,
we provide 10 billing profile.
Active
-
Click on check box, active or inactive the billing profile.
Name
-
It is the name of billing profile. The maximum allowed
Account Usage time
-
Charge
-
characters length is 12.
The duration of the billing period. When this period
expires, user account will be discontinued.
Enter the unit rate amount (i.e. 35.00) that most of
your accounts are charged for one day of service.
54
WSG-401 User Manual
Figure 3-41 Post-paid Procedure Diagram
Click Apply button to save the new settings.
Click Apply button, the success dialog box appears. Click on Back to return to Billing setting screen.
Figure 3-42 Success Dialog Box
WSG-401 User Manual
55
3-2-6 Accounting
This function allow service provider to generate the subscriber accounts.
Figure 3-43 Accounting Setting Screen
56
WSG-401 User Manual
Item
Default
Description
Expiration
Un-used account will
12 hours Enter the number of hours.
be deleted after
~hours automatically
Accumulation account 3 months Enter the number and select time unit from list box.
will be deleted after
logged in ~
Printout
Number of copies to
1
The system allows you to print all your bills. Enter the
print
number of copies.
Can be replenished by Enable
Click the check box to enable the replenish function.
subscriber
Figure 3-44 Account Process Diagram
Can be replenished by subscriber=Enable
WSG-401 User Manual
57
l Web-based Accounting Generator
Figure 3-45 Web-based Account Generator Panel Setting Screen
Item
Default
Button A~C -
Description
Define each button’s billing profile. Select one billing profile
by clicking in the list box.
Print to…
Account Generator Select printer to print out your account.
Printer
Click on button to preview and operate account generator panel.
Figure 3-46 Web-based Account Generator Panel
58
WSG-401 User Manual
Figure 3-47 Web-based Account Generator Printout
Figure 3-48 PC-connected Printer Printout
WSG-401 User Manual
59
Item
Pre-defined
Default
Disable
Description
The button presses on the printer will equal the No. “Button” in
the web-based account operator.
Press one time is button A, press two times is button B and
three times is button C. If press four times, the printer will not
do any action.
Incremental based
Enable
The usage time of account is based on the times of pressing
on Button ~
Button A button; you have to select one button by clicking in the list box.
EX. If Incremental based on Button A, press one time is button
A, and 3 times is button A x 3, which is same as now.
Discount Price Plan Disable
Enables or disables the discount price plan.
based on “Button
Presses”
Note: Before configuring the one-button printer accounting, you have to setting the billing profile of
web-based account generator panel.
60
WSG-401 User Manual
l WSG-ACG (Three-Button Printer)
Figure 3-49 Web-based Account Generator Panel Setting Screen
Item
Print to…
Default
Account
Description
Select printer to print out your account.
Generator
Printer
Use ~ for Discount Price Button A,
Select one button by clicking in the list box to assign
Plan based on “Button Disable
the base charge and select enable to active the
Presses”
discount price plan.
Note: Before configuring the one-button printer accounting, you have to setting the billing profile of
web-based account generator panel.
WSG-401 User Manual
61
l Discount Price Plan based on “Button Presses”
Figure 3-50 Discount Price Plan Setting Screen
Item
Default
Description
Charge by levels Enable
Enables or disables the charge by levels function.
Level
The level number of charge rate.
1~10
Conditions
When>= The discount condition.
Button Presses
-
Enter the times of pressing button.
Unit Price
-
Enter the amount of charge level.
Click Apply button to save the new settings.
Click Apply button, the success dialog box appears. Click on Back to return to Accounting setting
screen.
Figure 3-51 Success Dialog Box
62
WSG-401 User Manual
3-2-7 Credit Card
WSG-401 provides two credit card services (“Authorize.net” and “iTable”) that allow service provider
to authorize, process, and manage credit transactions directly from Internet.
Figure 3-52 Credit Card Setting Screen
Item
Default
Description
Authorize.net
Merchant ID
Empty
Enter your Merchant ID. This is a Merchant Identification
Number that you’re received from your Merchant Provider.
Merchant Transaction Key
Empty
The Merchant Transaction Key can be obtained directly
from “Authorize.net”. The Merchant Transaction Key is
similar to a password and is used by the Payment Gateway
to authenticate transactions.
Payment Gateway
~
Enter the address of Payment Gateway. The default value
is “https:// cardpresent.authorize.net/gateway/transact.dll”
Email Additional Information The Email Additional Information included subscriber username and
password would be sent to subscriber.
Email Additional Information Disable Indicates whether Email additional information should be
sent to the subscriber (customer).
Merchant Name
Disable Indicates whether Merchant Name should be sent to the
Enable/Disable
Merchant Name
Email of subscriber.
Empty
Enter the merchant’s company name. The maximum
allowed characters length is 40.
WSG-401 User Manual
63
Item
Username and Password
Default
Description
Disable The Email Additional Information included subscriber
Enable/Disable
username and password would be sent to subscriber.
Usage Time Enable/Disable Disable The Email Additional Information included subscriber
usage time would be sent to the subscriber.
iTable
Merchant ID
Empty
Enter your Merchant ID. This is a Merchant Identification
Number that you’re received from your Merchant Provider.
Terminal ID
Empty
Secure Server Address
-
Enter your Terminal ID. This is a Terminal Identification
Number that you’re received from your Merchant Provider.
Enter the secure server address. The default value is
“https://silverado.trivalley.com/merchant/processcc.asp”.
Click Apply button to save the new settings.
Click Apply button, the success dialog box appears. Click on Back to return to Accounting setting
screen.
Figure 3-53 Success Dialog Box
Please follow steps below to pay using credit card.
Step 1: Choose Credit Card service on the login page.
Click
Figure 3-54 Login Page
64
WSG-401 User Manual
Step 2: Select Service and enter payment information.
Figure 3-55 Service & Payment Information Setting Screen
Item
Default
Description
Payment Information
Credit card number
Empty
Credit card expiration date Empty
Enter your credit card number.
Enter the credit card expiration date. The allowed format is
MM/YY.
Enter Email Address
Empty
Enter your email address. The system will e-mail you
account information once your payment information has
been successfully authorized.
WSG-401 User Manual
65
Step 3: After valid payment information has been provided, the subscriber will obtain one valid account
to login or the Figure 3-67 screen will appear.
Figure 3-56 User Account Information
Figure 3-57
66
WSG-401 User Manual
3-2-8 Keypad
Figure 3-58 Keypad Setting Screen
Note: This function only support three-button printer
WSG-401 User Manual
67
Item
Use for Pre-Paid Billing
Default
Description
The system provides ten user definable hot keys through the use
of the + Key plus the 1 through 0 keys across the top of the
keypad.
Keypad Hot Key
+1~+0
It is the combination hot key for keypad application.
Billing Profile
-
Select the billing profile you want to assign to the
Use for Post-Paid Billing
Define the basic rate of accounts.
Base on ~
Minutes Select the billing unit by clicking in the list box.
Charge by levels
Enable
Enables or disables the charge by levels function.
Level (1~10)
1~10
The level number of charge rate.
Time Range
0
Enter the number.
Unit Price
-
Enter the amount of charge level.
combination hot key.
Please follow steps below to create accounts using keypad function.
l Use for Pre-Paid Billing
Step 1: Click the Billing in the Advanced Setup menu, select enable Pre-Paid, click Apply.
Figure 3-59 Billing Setting Screen
68
WSG-401 User Manual
Step 2: Click the Keypad in Advanced Setup Menu, define the Billing plan of pre-paid, and click Apply.
Figure 3-60 Keypad Hot Key
Step 3: You can use keypad to create subscriber accounts now. Press keypad hot key and then press
Enter. A new subscriber account is generated, and the account information should be printed.
Figure 3-61
Step 4: Subscriber can use this account to access Internet now.
WSG-401 User Manual
69
l Use for Post-Paid Billing
Step 1: Click the Billing in the Advanced Setup menu, select enable Post-paid, click Apply.
Figure 3-62 Billing Setting Screen
Step 2: Click the Keypad in Advanced Setup Menu, Define the billing plan of post-paid, click Apply.
Figure 3-63 Keypad Hot Key Setting Screen
70
WSG-401 User Manual
Step 3: You can use keypad to create subscriber accounts now. Press Enter, a new subscriber account
is generated, and the account information should be printed. This account information is
including serial number, username, password and account create time.
Figure 3-64
Step 4: When subscriber wants to terminate the Internet service, press *, serial number and then press
Enter, a bill should be printed.
Figure 3-65
WSG-401 User Manual
71
WSG-ACG operations
PS/2 Keypad
Enter the date (MonthDate)
Figure 3-66 Keypad Hot Key List
l Daily Account Report Printout
Press ABCAA
Figure 3-67 Daily Account
72
WSG-401 User Manual
l Monthly Account Report Printout
Press ABCBB
Figure 3-68 Monthly Account
l System Status Report Printout
Press ABCCC
Figure 3-69 System Status Report Printout
WSG-401 User Manual
73
l Network Report Printout
Press ABCAB
Figure 3-70 Network Report Printout
3-2-9 Customization
l Logo
This function allows uploading the service provider’s logo file, which can be shown on the standard
login page and account printout of PC-connected printer.
Figure 3-71 Logo Setting Screen
Item
File Path
Description
Enter the file pathname of the logo file in the File Path field.
Click Apply button to save the new settings.
74
WSG-401 User Manual
Click Apply button, the success dialog box appears. Click on Back to return to Customization setting
screen.
Figure 3-72 Success Dialog Box
l Login Page
Standard
For some service providers, they may hope to have a customize subscriber’s login page to the users.
This function helps them to realize the ideal. The page elements are including welcome image,
background color, article etc. Certainly the administrator can decide to use only standard form. The
WSG-401 provides three different login page formats, including standard, redirect, advanced and frame
format.
Figure 3-73 Standard Login Page Customization Setting Screen
Item
Default
Description
Logo
Disable
Title
Welcome Enter the title name of subscriber login page. The maximum
Select the check box to display service provider’s logo.
allowed characters length is 80.
Subtitle
Hot Spot
Enter the subtitle name of subscriber login page. The maximum
Internet
allowed characters length is 80.
Service
Footnote
Disable
Allow the administrator to input the footnote such like “Pleas
Contact to our Customer Service Center, EXT 142”. The
maximum character of the footnote is 240.
WSG-401 User Manual
75
Item
Copyright
Default
Description
Enable
The copyright is allowed the administrator to input a paragraph
in the subscriber login page for copyright information. The
maximum character of the copyright is 80.
Background Color FFFFFF
The background text color can be specified color. For the
specified text color format please views the color grid. The
allowed format is Hexadecimal.
Figure 3-74 Login Page Screen
Redirect
This allow service provider to redirect the subscriber’s browser to a specified home page.
Figure 3-75 Redirect Login Page Setting Screen
76
WSG-401 User Manual
Copy and paste the following HTML Code into your home page to produce redirect subscriber login
page.
Figure 3-76 Redirect Login Page Code Screen
WSG-401 User Manual
77
Advanced
This function allow user to design login page of WSG-401.
Figure 3-77 Advanced Login Page Setting Screen
Item
Default
Description
Welcome Slogan
Welcome The maximum allowed characters length is 80.
Page Background
None
The page background can be none or specified color. For the
background color format please views the color grid. The allowed
format is Hexadecimal (RGB values of Red, Green, and Blue, where
each component has a hexadecimal value of from 00 to FF. 000000 is
black and FFFFFF is white.)
Article
Empty
The article is allowed the administrator to input a paragraph in the
subscriber login page for advisement or announcement. The
maximum character of the article is 1024.
Article Text Color
000000
The article text color can be specified color. For the specified text color
format please views the color grid. The allowed format is
Hexadecimal.
Article Background None
The article background can be specified color. For the background
Color
color format please views the color grid. The allowed format is
Hexadecimal.
Information
Empty
Allow the administrator to input the text information such like address,
telephone number and fax information. The maximum character of the
information is 80.
Comments
Empty
Allow the administrator to input the text comments such like “Pleas
Contact to our Customer Service Center, EXT 142”. The maximum
character of the comment is 80.
78
WSG-401 User Manual
Figure 3-78 Color Gird
Frame
If “Frame” is selected the subscriber login page will be separate into Top Frame and Bottom Frame.
Bottom Frame is a default format for username and password input, Top Frame is allowed to be
specified a URL to link.
www.hinet.net
Figure 3-79 Frame Login Page Setting Screen
Item
Default
Description
Top Frame URL Link Empty The input format can be http://www.yahoo.com. The maximum
character of the URL Link is 200.
Bottom Frame
-
This frame will show the standard login page.
l Information Window
This function allow service provider can decide whether they want an “Information Window” pop-up on
subscriber PC when authenticate successful or not and specified text of information window.
Subscriber can type “http://1.1.1.1/info” to open the information window again or enter
“http://1.1.1.1/logout” to logout immediately if accumulation billing selected.
WSG-401 User Manual
79
Figure 3-80 Example-Login Page Screen
Figure 3-81 Example-Login Page Screen
Figure 3-82 Information Window
80
WSG-401 User Manual
Billing Type=Time to Finish
Can be replenished by subscriber=Disable
Figure 3-83 Information Window
Billing Type=Time to Finish
Can be replenished by subscriber=Enable
WSG-401 User Manual
81
Figure 3-84 Information Window
Billing Type=Accumulation
Can be replenished by subscriber=Disable
Figure 3-85 Information Window
Billing Type=Accumulation
Can be replenished by subscriber=Enable
Figure 3-86Logout Successfully Dialog Box
Billing Type=Accumulation
82
WSG-401 User Manual
Figure 3-87 Disconnected Dialog Box
Figure 3-88 Alarm Dialog Box
WSG-401 User Manual
83
l Account Printout
This function allow service provider to specified text of account printout.
Figure 3-89 Account Printout Customization Setting Screen
Click Apply button to save the new settings.
84
WSG-401 User Manual
Click Apply button, the success dialog box appears. Click on Back to return to Account Printout
Customization setting screen.
Figure 3-90 Success Dialog Box
t
WSG-401 User Manual
85
Figure 3-91 Account Generator Printer Printout
Figure 3-92 Account Generator Printer Printout
86
WSG-401 User Manual
l Credit Card
Standard Login Page
This function allow service provider to customize the additional credit card message for the standard
login page.
Figure 3-93 Credit Customization Setting Screen
Figure 3-94 Standard Login Page
WSG-401 User Manual
87
Service Selection Page
This function allow service provider to customize the additional credit card message for the standard
login page.
Figure 3-95 Service Selection Page Setting Screen
88
WSG-401 User Manual
Figure 3-96 Example-Service Selection Page
WSG-401 User Manual
89
Successful Page
Figure 3-97 Successful Page Setting Screen
Figure 3-98 Example-Successful Page
90
WSG-401 User Manual
Fail Page
This function allow service provider to customize the message for the fail page.
Figure 3-99 Fail Page Setting Screen
Figure 3-100 Example-Fail Page
Click Apply button to save the new settings.
Click Apply button, the success dialog box appears. Click on Back to return to Credit Card
Customization setting screen.
Figure 3-101 Success Dialog Box
WSG-401 User Manual
91
3-2-10 Pass Through
This function allow administrator to set some special devices pass through the WSG-401 system.
Because some network devices might be constructed under the WSG-401. However these devices
needn’t be checked and authorized. The WSG-401 provides a pass through list and the administrator
can control which devices can be pass through with authentication.
Figure 3-102 Pass through Setting Screen
Item
Pass Through
Default
Disable
Description
Enables or disables the pass through function.
Destination URL/IP Address Pass Through
URL or Website
Empty
Enter the URL Page; please use this format such like
“http://www.yahoo.com”. The maximum character of the URL
Page is 200.
92
WSG-401 User Manual
Item
Default
Description
Start IP Address
Empty
Enter the start IP address of you wants pass through.
End IP Address
Empty
Enter the end IP address of you wants pass through.
Subscriber IP/MAC Address or LAN Device Pass Through
Start IP Address
Empty
Enter the start IP address of you wants pass through.
End IP Address
Empty
Enter the end IP address of you wants pass through.
IP Address
Empty
Enter the IP address of you wants pass through.
Subnet Mask
Empty
Enter the subnet mask of you wants pass through.
MAC Address
Empty
Enter the MAC address of you wants pass through.
Mask
Empty
Enter the subnet mask of you wants pass through.
Pass Through List Display the pass through Information of WSG-401.
No.
-
The index number of pass through address.
Active
Disable
Click on check box, active or inactive the pass through address.
Address List
-
Display the pass through address(s).
Type
-
Display the type of pass through address.
Delete
Disable
Select the check boxes and click ‘Delete’ to delete the pass
through address(s).
Click Add to List button to add a new entry.
Click Apply button to save the new settings.
Click Delete All & Apply button to delete all entries.
Note: The priority of "pass through" is higher than "Filtering".
WSG-401 User Manual
93
3-2-11 Filtering
Filtering allows the system administrator to have a list of restricted destinations, which is useful to block
specified Internet websites or Intranet areas.
Figure 3-103 Filtering Setting Screen
Item
Default
Description
Filtering
Disable
Enables or disables filtering function.
HTTP Message
The Web
Enter the http message.
to display when a Site is
website is
blocked by
blocked
System
Restrict Destination
URL or Website
Empty
Enter the URL Page of you wants to filter; please use this format
such like “http://www.yahoo.com”. The maximum character of the
URL Page is 200.
Start IP Address Empty
Enter the start IP address of you wants to filter.
End IP Address
Enter the end IP address of you wants to filter.
94
Empty
WSG-401 User Manual
Item
Default
Description
IP Address
Empty
Enter the destination IP address of you wants to filter.
Subnet Mask
Empty
Enter the destination subnet mask.
No
-
The index number of filtering address.
Active
Disable
Click on check box, active or inactive the filtering address.
Address List
-
Display the filtering address(s).
Delete
Disable
Select the check boxes and click ‘Delete’ to delete the filtering
address(s).
Click Add to List button to add a new entry.
Click Apply button to save the new settings.
Click Delete All & Apply button to delete all entries.
Note: The priority of "pass through" is higher than "Filtering".
WSG-401 User Manual
95
3-2-12 Share
This feature allows sharing the network devices like printer after subscriber successful login.
Figure 3-104 Share Device Setting Screen
Item
Default
Description
Share LAN resource
Disable Enables or disables share LAN resource function.
Resource Name
Empty Enter the device name.
Resource IP Address
Empty Enter the IP address of device.
Resource MAC Address Empty Enter the MAC address of device.
Share LAN resource List
No.
-
Active
Disable Click on check box, active or inactive the share LAN device.
The index number of share LAN device.
Resource Name
-
Display the device name.
IP Address
-
Display the IP address of device.
MAC Address
-
Display the MAC address of device.
Delete
Disable Select the check boxes and click ‘Delete’ to delete the share
device(s).
96
WSG-401 User Manual
Note:
1. You must use the “Search IP” method to search for a device on the network. Please follow steps
below to search your device.
F Click Start, and then click Search.
F Click Computers or People.
F Click “A computer on the network”.
F In Computer, type the IP address of the device you want to find. Click Search.
2. The function support only Unicast and IP Protocol.
Click Add to List button to add a new entry.
Click Apply button to save the new settings.
Click Delete All & Apply button to delete all entries.
3-2-13 Portal Page
This feature allows redirecting subscriber’s browser to a specified portal page after successful login.
Figure 3-105 Portal Page Setting Screen
Item
URL Link
Default
Empty
Description
Enter
the
URL
Link
page.
The
input
format
can
be
“http://www.yahoo.com”. The maximum character of the URL Link # is
200.
Click Apply button to save the new settings.
Click Apply button, the success dialog box appears. Click on Back to return to Portal Page setting
screen.
Figure 3-106 Success Dialog Box
WSG-401 User Manual
97
3-2-14 Advertisement
The system allow service provider to input 10 URL links for advertisement link purpose.
Figure 3-107 Advertisement URL Link Setting Screen
Item
Default
Description
Frequency One Time Only One Time Only—One Time Only means to send the advertisement link
once after the subscriber Login.
Every~Min(s)—The field means to send the advertisement link every
interval minutes. The value range is 1 to 60 (minutes).
Sequence Randomly
Randomly—Display the advertisement page in the random order.
From 1 to 10 —Display the advertisement page in the order as setting.
URL Link Empty
This function allows the administrator to input ten different websites in
1~10
the table for advertisement. And these 10 websites will display to the
subscribers at random when the subscribers login in the WSG-401
system. The input format can be “http://www.yahoo.com”. The
maximum character of the URL Link # is 200.
Click Apply button to save the new settings.
98
WSG-401 User Manual
Click Apply button, the success dialog box appears. Click on Back to return to Advertisement URL Link
setting screen.
Figure 3-108 Success Dialog Box
3-2-15 Walled Garden
We prepare ten URL links that allows subscriber to access the specific Web pages even they didn’t
have a username or password. It’s free trying and can use for advertisement.
Yahoo
www.yahoo.com
MSN
www.msn.com
Microsoft
www.microsoft.com
Figure 3-109 Walled Garden
WSG-401 User Manual
99
Name
Figure 3-110 Login Page
Item
Description
Link 1~10
Name
The name is allowed user to set the prompt string in user customize login page. The
maximum allowed characters length is 80.
URL 1~10
The input format can be “http://www.yahoo.com”. The maximum character of the
Link# is 200.
Click Apply button, the success dialog box appears. Click on Back to return to Walled Garden setting
screen.
Figure 3-111 Success Dialog Box
100
WSG-401 User Manual
3-2-16 DDNS
The DDNS service (Dynamic Domain Name Service), an IP Registry provides a public central database
where information such as email addresses, host names, IP addresses etc. can be stored and retrieved.
This solves the problems if your DNS server uses an IP associated with dynamic IP addresses. When
the ISP assigns the WSG-401 a new IP, the WSG-401 must inform the DDNS server the change of this
IP so that the server can update its IP-to-DNS entry. Once the IP-to-DNS table in the DDNS server is
updated, the DNS name for your web server (i.e., xyz.dyndns.org) is still usable.
Figure 3-112 DDNS Setting Screen
WSG-401 User Manual
101
Item
Force to update every
Default
1 days
~day(s) when WAN IP
Description
Enter a number in the field to set the force update interval
(in days).
address keeps no
change
No
01~03
The index number of a DDNS account.
Active
Disable
Click on check box, active or inactive the DDNS record.
Click the Update Status Now button to do manual update.
Settings
Enter the account information of DDNS Server.
Status
YY/MM/DD
Display the update date, time and status. The Status area
HH:MM:SS:
shows the update time and current state of the DDNS
Client.
N/A—DDNS Client service not installed,
Update Successfully—DDNS Client service installed;
service running.
Update Fail—DDNS Client service installed; service not
running.
Service Provider
Dyndns.org
Select a DDNS service provider by clicking in the list box.
(www.dyndns.org) Note: Before configuring the DDNS settings, you have to
register a dynamic domain at one of the dynamic domain
service providers’ list box.
Registered Host Name
Empty
Enter the host name of DDNS server.
Login Name
Empty
Enter the user name of DDNS server.
Password
Empty
Enter the user password of DDNS server.
Email Address
Empty
Enter your email address. The DDNS Server will e-mail
you important information once your Internet Name has
been successfully registered.
Wildcards (optional)
Disable
Enable
this
function
*.mydomain.dyndns.org
to
be
and
able
not
to
use
only
mydomain.dyndns.org.
Click Apply button to save the new settings.
102
WSG-401 User Manual
Click Apply button, the success dialog box appears. Click on Back to return to DDNS setting screen.
Figure 3-113 Success Dialog Box
3-2-17 LAN Devices
Administrator can direct remote control to LAN Devices via the WSG-401 implemented the feature.
Figure 3-114 LAN Devices Setting Screen
Item
Polling Interval
Default
5 Min.
Description
The default value is 5 minute. The Polling Interval valid range is 1 to
1440.
WSG-401 User Manual
103
Item
Default
Device Name
Empty
Virtual Port
0
Description
The LAN device name. The maximum character of the device name
is 20.
The virtual port number valid range is 60001 to 60050.
Device IP Address
Empty
The IP address of LAN device.
Device Server Port
0
The server port of LAN device.
Device MAC Address Empty
The MAC address of LAN device. For input the device MAC
Application
TCP
The protocol type of LAN device.
Interface
Wired
The interface of LAN device.
address, please use this format such like”00304f8D2296”.
Click Delete All button to delete all entries.
Click Apply button to save the new settings.
Note: The system does not support FTP.
3-2-18 Syslog
The function allows the device to transmit event messages to your syslog server or your email address
for monitoring and troubleshooting.
l Syslog Setting
Figure 3-115 Syslog Setting Screen
104
WSG-401 User Manual
Item
Syslog
Default
Description
Disable
Enables or disables the syslog server function.
Empty
Enter syslog server’s IP address. The WSG-401 will send all of
Syslog on LAN
Server IP Address
its logs to the specified syslog server.
Server MAC Address Empty
Enter the syslog server’s MAC address. The WSG-401 will
send all of its logs to the specified syslog server.
Syslog on WAN
Server 1 IP
Empty
Enter IP address of first syslog server.
Empty
Enter IP address of second syslog server.
Disable
Enables or disables the send to e-mail function.
Address
Server 2 IP
Address
Send to Email
E-mail Server
IP Address or Domain Empty
Enter the SMTP server IP address or domain name.
Name
SMTP Port
25
The SMTP port allowed range is 25 or 2500 to 2599.
E-mail (SMTP) Server Disable
If your SMTP server requires authentication before accepting
needs to check my
e-mail, click on check box. These values (username and
account
password) are supplied by your network administrator, SMTP
server provider or ISP.
Username
Empty
Enter the username for the SMTP server.
Password
Empty
Enter the password for the SMTP server
Empty
Enter the name you would like to appear in the “message from”
Email From
Name
field of your outgoing message.
Email Address
Empty
Enter your e-mail address. This is the address others will use to
send email to Email Address 1/Email Address 2.
Email To
Email Address 1
Empty
Enter your first e-mail address to receive the logs.
Email Address 2
Empty
Enter your second e-mail address to receive the logs.
Click Apply button to save the new settings.
WSG-401 User Manual
105
Click Apply button, the success dialog box appears. Click on Back to return to Syslog setting screen.
Figure 3-116 Success Dialog Box
l Log Categories
Figure 3-117 Log Settings Screen
106
WSG-401 User Manual
Item
Interval Time
Syslog
Disable
Email
Disable
Description
Click on check box, send log information to your syslog
server.
Click on check box, send log information to your e-mail
address.
System
Syslog Information
60 minutes
The log included system information would be sent
according to specified interval time.
Format:
(Id, Mac Address) (System Uptime, 0 days 00h:04m:00s)
(Location Name, Location Name) (WAN, FrameTxOK,
FrameRxOK,
FrameTxError,
FrameRxError)
(LAN,
FrameTxOK, FrameRxOK, FrameTxError, FrameRxError)
(Wireless,
FrameTxOK,
FrameRxOK,
FrameTxError,
FrameRxError)
System Boot Notice
When System If device have been rebooted, the log would be sent.
reboot
Format: (Id, MAC Address) (System Up)
System Manager
When system A log will be sent if system manager (Administrator,
Activity Information
manager login Supervisor or Account Manager) login to or logout from the
or logout
device.
Format:
(Id, Mac Address) (System Account Activity Information,
Username, User IP, Status)
Username:
Administrator
|
Supervisor
|
Accounting
Operator
Status: Login | Logout | Idle Time Out
Subscriber
Wireless Association
Information
60 minutes
A log included wireless associated users information would
be sent according to specified interval time.
Format:
(Id, Mac Address) (Wireless Association Information,
Number of associated users, Start Number, End number)
(Signal strength, Signal quality, Connection speed, MAC
address)(…)(…)(…)
WSG-401 User Manual
107
Item
Logged-in Users
Interval Time
60 minutes
Description
A log included logged-in users information would be sent
according to specified interval time.
Format:
(Id, Mac Address) (Logged-in Users, Type, Number of
logged-in users, Start Number, End number) (Username,
User IP, User MAC, Interface, Login time, RxData count,
TxData count)(…)(…)
Type: Dynamic | Super
If the type of Logged-in user is Super Subscriber, Username
will be “********”.
Proprietary Accounting
Account Created
When an
A log would be sent if account were created.
account is
Format:
created.
(Id, Mac Address) (Account Create, Type, S/N, Username,
Unit, Account usage time, Billing profile information)
Type: TimeToFinish | Accumulation | PostPaid
Billing profile information: [index, name]
Account usage time: 00:59:59 (example)
Account Activated
When an
A log would be sent if account were activated.
account is
Format:
activated
(Id, Mac Address) (Account Activate, username, user IP,
user MAC, Interface)
Subscriber Trace
When
A log including subscriber’s login or logout time will be sent
subscriber
once after subscriber logout.
logout
Format:
(Id, Mac Address) (Subscriber Trace, Type, Event, S/N,
Username, User IP, User MAC, Interface, Login time, Logout
time, Usage Time, Time Left, RxData count, TxData count)
Type: TimeToFinish | Accumulation | PostPaid | Super
Event: Finished | Replenished | Logout | Idle-Timeout |
Account Expired | Deleted
If the type of Subscriber Trace is Super, the Username will
be “********”, and S/N will be “******”.
Usage time: 00:59:59 (example)
108
WSG-401 User Manual
Subscriber Trace Relationship
Type
Event
Time Left
TimeToFinish
Finished
00:00:00
TimeToFinish
Replenished
00:12:00 to S/N000004
TimeToFinish
Deleted
00:12:00
Accumulation
Finished
00:00:00
Accumulation
Replenished
00:12:00 to S/N000004
Accumulation
Logout
00:48:00
Accumulation
Idle-Timeout
00:48:00
Accumulation
Deleted
00:48:00
Accumulation Account Expired
00:48:00
PostPaid
Logout
******
PostPaid
Idle-Timeout
******
PostPaid
Deleted
******
PostPaid
Finished
******
Item
Interval Time
Description
Billing
Billing Log
When log
A log would be sent after a billing log is created.
created
Format:
(Id, Mac Address) (Billing Log, Type, S/N, Username, Billing
profile information, Units, Usage time, Bill, Payment)
Type: TimeToFinish | Accumulation | PostPaid
Billing profile name: [Name]
Usage time: “00:59:59” (example)
Billing profile information: [index, name]
Payment: Cash | Credit Card
“Credit Card” does not support “PostPaid”.
If Type is “PostPaid”, the billing profile information and Units
will be “*”.
WSG-401 User Manual
109
Item
Interval Time
Description
LAN Devices Management Category
LAN Devices Information
60 minutes
A log including current LAN Devices Status will be sent
according to specified interval time.
Format:
(Id, Mac Address) (LAN Devices Information, Number of
devices, Start Number, End number) (Device name,
Status)(…)(…)
LAN Devices Alarm
When device A log will be sent if one of the LAN Devices detected results
fail
is "Fail".
Format:
(Id, Mac Address) (LAN Device Alarm, Device name, FAIL)
Click Apply button to save the new settings.
Click Apply button, the success dialog box appears. Click on Back to return to Logs setting screen.
Figure 3-118 Success Dialog Box
110
WSG-401 User Manual
3-2-19 Wireless
Figure 3-119 Wireless Setting Screen
Item
Default
Description
General Settings
The ESSID is the unique name that is shared among all points in a
ESSID
wireless network. It is case sensitive and must not exceed 32
characters.
Channel
6
Select the channel ID for wireless connection.
Disables or enables the use of the WEP algorithm. Enabling the
WEP Encryption Disable
security can protect your data while it is transferred from one
station to another.
WSG-401 User Manual
111
l WEP Key Setting
Figure 3-120 WEP Key Setting
Item
Description
Default
WEP Encryption
64 bit
Mode
HEX
The WSG-401 supports 64-bit, 128 bit or 256 bit WEP
encryption.
Options: HEX (Hexadecimal) and ASCII (American
Standard Code for Information Interchange).
WEP Key
1
This selects which of the Keys the WSG-401 uses when
it transmits. You can change the selected encryption
key every now and then to increase the security of your
network.
Enter 5 characters for ASCII 64-bit WEP Key.
Enter 10 characters for Hex 64-bit WEP Key.
Enter 13 characters for ASCII 128-bit WEP Key.
Enter 26 characters for Hex 128-bit WEP Key.
Enter 29 characters for ASCII 256-bit WEP Key.
Enter 58 characters for Hex 256-bit WEP Key.
Click Apply button to save the new settings.
Click Apply button, the success dialog box appears. Click on Close to return to Wireless setting
screen.
Figure 3-121 Success Dialog Box
112
WSG-401 User Manual
Item
Default
Beacon Interval 100
Description
This value valid range is 1 to 1000 indicates the frequency interval
of the beacon.
This value valid range is 256 - 2342. This setting determines the
packet size at which the WSG-401 issues a request to send (RTS)
RTS Threshold
2432
before sending the packet. A low RTS Threshold setting can be
useful in areas where many client devices are associating with the
WSG-401, or in areas where the clients are far apart and can
detect only the WSG-401 and not each other.
This setting determines the size at which packets are fragmented.
Fragmentation
Threshold
2346
Enter a setting ranging from 256 to 2346 bytes. Use a low setting
in areas where communication is poor or where there is a great
deal of radio interference.
This setting, always a multiple of the beacon period, determines
how often the beacon contains a delivery traffic indication
DTIM Interval
3
message (DTIM). The DTIM tells power-save client devices that a
packet is waiting for them. The DTIM Interval value valid range is
1 to 65535.
Transmission
1-2-5.5-22 The basic transfer rates should be set depending on the speed of
Rates
(Mbps)
your wireless network. The default setting is 1-2-5.5-22 (Mbps).
The preamble type is a section of data at the head of a packet that
Preamble Type
Long
contains information the Wireless PnP Subscriber Gateway and
Preamble
client devices need when sending and receiving packets. The
setting menu allows you to select a long or short preamble type.
WSG-401 User Manual
113
Item
Default
Description
Select left antenna, right antenna or diversity antenna.
Left Antenna―
If your device has removable antennas and you install a high-gain
antenna on the device's left connector, you should use this setting
for both receive and transmit. When you look at the device's back
panel, the left antenna is on the left.
Right Antenna―
Antenna
Diversity
If your device has removable antennas and you install a high-gain
Selection
Antenna
antenna on the device's right connector, you should use this
setting for both receive and transmit. When you look at the
device's back panel, the right antenna is on the right.
Diversity Antenna―
This default setting tells the device to use the antenna that
receives the best signal. If your device has two fixed
(non-removable) antennas, you should use this setting for both
receive and transmit.
114
WSG-401 User Manual
Item
Default
Description
Select open system, shared Key or both.
Open System — Allows any device to authenticate and then
attempt to communicate with the WSG-401. Using open
authentication, any wireless device can authenticate with the
WSG-401, but the device can only communicate if its WEP keys
match the WSG-401. Devices not using WEP do not attempt to
authenticate with a Wireless Service Gateway that is using WEP.
Open authentication does not rely on a RADIUS server on your
network.
Shared Key—During shared key authentication, the WSG-401
sends an unencrypted challenge text string to any device
Authentication
Type
Both
attempting
to
communicate
with
the
WSG-401.
The
device-requesting authentication encrypts the challenge text and
sends it back to the WSG-401. If the challenge text is encrypted
correctly, the WSG-401 allows the requesting device to
authenticate. Both the unencrypted challenge and the encrypted
challenge can be monitored, however, which leaves the WSG-401
open to attack from an intruder who calculates the WEP key by
comparing the unencrypted and encrypted text strings. Because
of this weakness, shared key authentication can be less secure
than open authentication. Like open authentication, shared key
authentication does not rely on a RADIUS server on your network.
Both—With this setting stations can communicate with or without
data encryption.
Enable― It allows devices that do not specify an SSID to
associate with the Wireless Service Gateway.
Disable― Devices that do not specify an SSID (devices that are
SSID Broadcast Enable
"broadcasting" in search of an access point to associate with) are
not allowed to associate with the device. With no selected, the
SSID used by the client device must match exactly the Wireless
Service Gateway's SSID.
WSG-401 User Manual
115
Click Apply button to save the new settings.
Click Apply button, the restart dialog box appears. Click on Apply to restart the system.
Figure 3-122 Restart Dialog Box
This operation will load the default manufacturer configuration to the system. All this page
(Wireless) configuration setup will be replaced by default settings.
3.3
System Status
Display WSG-401 system basic status, including,
1.
System
2.
Account List
3.
Account Log
4.
Current User
5.
DHCP Clients
6.
Session List
7.
LAN Devices
Figure 3-123 System Status Item Screen
116
WSG-401 User Manual
3-3-1 System
The System Information Menu displays current system basic information including the service
connection message, host name, LAN, WAN, DHCP Configuration, DNS, E-mail Redirection, SSL
Certificate, network traffic Information and the system firmware version number.
Figure 3-124 System Status Screen
WSG-401 User Manual
117
3-3-2 Account List
You can display a list of all the account information on this device. This table includes the username,
password, usage time, time created, login time, expiration time and status.
Figure 3-125 Account List
Click on refresh button to update the account list page.
Click the column button to sort the column in ascending/descending order.
Select the check boxes and click ‘Delete’ to delete the accounts.
Delete all accounts in account list.
Note: This page will refresh automatically every 5 minutes.
118
WSG-401 User Manual
3-3-3 Account Log
The account log shows the accounts’ log information.
Figure 3-126 Account Log
This allow you to export the account logs to a text file format.
Click on Clear Log to remove all account log entries.
Click on refresh button to update the account log page.
Click the column button to sort the column in ascending/descending order.
WSG-401 User Manual
119
3-3-4 Current User
Display the current logged-in subscribers’ status. It allow service provider to disconnect any
subscribers.
Figure 3-127 Current User List
Click on refresh button to update the current user list page.
Click the column button to sort the column in ascending/descending order.
Select the check boxes and click ‘Disconnect’ to disconnect accounts.
Disconnect all accounts in current user list.
3-3-5 DHCP Clients
The DHCP client table shows the current DHCP users on the LAN.
120
WSG-401 User Manual
3-3-6 Session List
The remote site administrator could monitor the real time usage status of WSG-401 via this page.
Figure 3-128 Session List Screen
3-3-7 LAN Devices
You can manage all devices by clicking on device name to access device’s Web-based interface.
Figure 3-129 LAN Devices Status Screen
WSG-401 User Manual
121
3.4 System Tools
This allows service provider or administrator to process Firmware upgrade, change password and
backup or restore configuration.
1.
Configuration
2.
Firmware
3.
System Account
4.
SSL Certificate
5.
Ping Command
6.
Restart
7.
Logout
Figure 3-131 System Tools Item
3-4-1 Configuration
Use the Configuration item to save, restore or reset configuration parameters of the WSG-401.
Figure 3-132 Configuration Setting Screen
Item
Backup
122
Default
Description
Click it to save the system configuration to your computer.
WSG-401 User Manual
Item
Default
Remote TFTP Server IP Empty
Description
Enter the IP address of TFTP Server.
Address
File Name
Empty
Enter the file name in the Text File Name field.
Restore
Click it to restore your system configuration.
Local PC File Path
Empty
Enter the file pathname of the system configuration file in the
file path field.
Remote TFTP Server IP Empty
Enter the IP address of TFTP Server.
Address
File Name
Empty
Reset the system back
Erase all setting and back to factory setting.
Enter the file name in the Text File Name field.
to factory defaults
Keep subscriber profile Disable
Click the keep subscriber profile to change all the parameters
into factory setting but still reserve the subscriber profiles.
3-4-2 Firmware Upgrade
The Firmware Upgrade menu loads updated firmware to be permanent in flash ROM. The download file
should be a binary file from factory; otherwise the agent will not accept it. After downloading the new
firmware, the agent will automatically restart it.
l Manual Firmware Upgrade
Figure 3-133 Manual Firmware Upgrade Setting Screen
Item
Default
Description
This allow administrator to upgrade the firmware via HTTP.
Local PC File Path
Empty
Enter the file name and location in the Local PC File Path
field.
This allows administrator use TFTP server to upgrade firmware.
Remote TFTP Server IP Empty
Enter the IP address of TFTP Server.
Address
File Name
Empty
Enter the file name in the File Name field.
Note: Before downloading the new firmware, users must save the configuration file for restore
configuration parameters of the device.
WSG-401 User Manual
123
l Scheduled Firmware Upgrade
Scheduled Firmware Upgrade is a program that enables an automatic upgrade to the latest firmware
version through the TFTP server.
Figure 3-134 Scheduled Firmware Upgrade Setting Screen
Item
Default
Disable/Enable
Disables or enables the scheduled firmware upgrade function.
Description
TFTP Server IP
Empty
Enter the IP address of TFTP Server.
File Synchronization
Empty
Enter the file name and location in the File
Synchronization field.
Click the button to display synchronization file example.
Frequency
Weekly
Set the firmware upgrade time. The default value is
“Weekly”.
124
WSG-401 User Manual
3-4-3 System Account
Use the System Account screen to change the system accounts.
Figure 3-135 System Account Setting Screen
Item
Description
Username The username can consist of up to 20 alphanumeric characters and is sensitive.
Password
The password can consist of up to 20 alphanumeric characters and is sensitive.
Confirm
The password for confirmation.
WSG-401 User Manual
125
l Administrator Account
Step 1: Start your Web browser and enter the factory default IP address 192.168.0.1 in your browser’s
location box. Press Enter.
Figure 3-136 Web Browser Location Field (Factory Default)
Step 2: The WSG-401 configuration main menu will appear. Enter “admin” (default) as the Username
and “password” (default) as the password and click “Getting Started”. If you are first time
setting the system, the wizard setup screen will appear.
Username: admin
Password: password
Figure 3-137 Administrator Account Login Screen (First Time)
126
WSG-401 User Manual
l Web-Based Accounting Manager
Step 1: Start your Web browser and enter the factory default IP address 192.168.0.1 in your browser’s
location box. Press Enter.
Step 2: The WSG-401 configuration main menu will appear. Enter “account” as the Username and
“account” as the password and click “Getting Started”
Username: account
Password: account
Figure 3-138 Web-Based Accounting Manager Login Screen
Step 3: After a valid user name and password have been provided, the account Generator Panel
homepage will appear.
Figure 3-139 Account Generator Panel
WSG-401 User Manual
127
l Supervisor Account
Step 1: Start your Web browser and enter the factory default IP address 192.168.0.1 in your browser’s
location box. Press Enter.
Step 2: The WSG-401 configuration main menu will appear. Enter “supervisor” as the Username and
“supervisor” as the password and click “Getting Started”.
Username: supervisor
Password: supervisor
Figure 3-140 Supervisor Account Login Screen
Step 3: After a valid user name and password have been provided, the WSG-401 configuration
homepage will appear.
Disable
Figure 3-141 System Status Screen
128
WSG-401 User Manual
l Super Subscriber Account
Start your Web Browser; a subscriber login page will appear. Enter “super” as the Username and
“super” as the password and click “Enter”, you can use Internet now.
Username: super
Password: super
Figure 3-142 Subscriber Login Page
3-4-4 SSL Certificate
The function allows you to download the registered CA certificate into the WSG-401.
Figure 3-143 SSL Certificate
Note: The password field must the same as the CA’s registered password.
WSG-401 User Manual
129
3-4-5 Pin Command
The Ping function can check the WSG-401 networking connective or not.
Figure 3-144 Ping Command Screen
3-4-6 Restart
If your WSG-401 is not operating correctly, you can choose this option to display the restart WSG-401
screen. Clicking the apply button restart the WSG-401, with all of your settings remaining intact.
Figure 3-145 Restart Screen
3-4-7 Logout
If you would like to leave the configuration page, please click apply to exit.
Figure 3-146 Logout Screen
130
WSG-401 User Manual
Appendix A RJ-45 Connector Description
RJ-45 Ethernet Port
The WSG-401 RJ-45 Ethernet port can connect to any networking devices that use a standard LAN
interface, such as a Hub/Switch Hub or Router. Use unshielded twisted-pair (UTP) or shield twisted-pair
(STP) cable to connect the networking device to the RJ-45 Ethernet port.
Depending on the type of connection, 10Mbps or 100Mbps, use the following Ethernet cable, as
prescribed.
10Mbps: Use EIA/TIA-568-100-Category 3, 4 or 5 cable.
100Mbps: Use EIA/TIA-568-100-Category 5 cable.
Figure A-1 RJ-45 Connector and Cable Pins
Note:
F To prevent loss of signal, make sure that the length of any twisted-pair connection does not exceed
100 meters.
WSG-401 User Manual
131
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising