DF3600U
Universal Flash
SUNPAK
DF3600U
Thank you for purchasing this Sunpak flash.
Before using the DF3600U, please take a moment to read this manual and
your camera’s instruction manual to familiarize yourself with the flash
operations.
Safety instruction
1, Never trigger the flash around flammable gas or liquid gas (such as
gasoline and solvents)! There is risk of explosion!
2, Neither shoot with the flash at drivers who are driving cars, buses or trains,
nor the rider of motor and bicycle. They may be temporarily blinded by the
bright light and cause traffic accident.
3, Never trigger the flash at close range of your eyes! Using the flash directly
at people or animal's eyes will damage the retinas and cause serious visual
disturbance, even blindness.
4, Only use the batteries listed in this manual!
5, Never place the batteries in high-temperature environment, such as in
direct sunlight or in the fire.
6, Remove the drained battery from the flash. As the alkaline liquid exuding
from the battery will damage the flash.
7. Keep the flash away from the water (such as the rain).
8, Note: Protect the flash in extreme high temperature or humid
environment.
9, Do not place the flash in car dashboard glove compartments. When
triggered flash, do not place an opaque object in front of the reflection screen or
above, and no dirt is allowed on the reflective screen. Otherwise the highenergy flash will burn reflective objects on the screen or damage screen.
10, Never open the flash by yourself. It has danger of high voltage. There are no
user replaceable parts inside.
1
11, Do not fire the flash at full power more than 10 times continuously. Wait 5
minutes every 10 continuous full power flashes.
12, When in full power output by quickly back continuous use flash, The
zoom setting should be less than 35 mm, due to the effect of high heat flash
diffuser will be hot.
13, Rapid temperature changes can lead to water vapor condensation. In this
situation, give the flash time to gradually adapt to the environment temperature.
14, Never use any defective batteries in this flash.
The DF3600U Features
1, High Guide Number of 118/feet @ ISO 100
2, Wireless SLAVE unit function: Compatibility with the Canon and
Nikon Wireless flash system,realize TTL off camera,manual and
frequency flash
3, Powered by 4 - AA batteries (Alkaline, Ni-CD, Ni-MH)
4, Dual mode, Universal hot shoe contacts
5, High-Speed Sync: Max hight speed Sync 1/8000s
6, TTL flash
7, Manual flash
8, Multi flash
9, S1,S2 Light flashing mode
10, Flash exposure FEB, exposure compensation, flash exposure lock
(FEL/FV)
11, The camera menu access funtion (Only for the newest Canon
Version)
12, Rear-curtain Sync
13, Voice prompt
14, Custom function
15, Power save mode
16, Overheating protection
17, Manual,Auto zoom
18, Automatic save function
19, Large size LCD display
20, Quick response: Full output recycle time only 2.3 seconds
2
Description of Parts
Built-in bounce card
Flash head tilt angle scale
Built-in wide-angle
diffuser
Flash head
Serial number
Liquid crystal display
Synchronous sockets
Press two button at the same
time restore factory settings
High-speed synchronous /
Rear-curtain sync / Ordinary
flash switch button
Parameter Settings button
/ MASTER select button
Backlight / LED Mode
switch button
MODE select buttons /
SLAVE select button
Focal length/ Wireless
parameter settings button /
Custom function settings
button
Flash sensor
Battery cover
ON/OFF switch button
Select/Settings
button group
Installation feet
Install pin
Flash test button / Wake
button / Charge lamp
Hot shoe contact
3
4
Auto-focus auxiliary AF assist lamp
When shooting under a dark conditions, the Automatic AF Assist which is
built into the flash light may temporarily project red light to assist focusing.
In some cases it may interfere with your subject. If this happens, you can
switch to Manual focus (M) or to the Custom function (Fn - 08) close focus
light.
For detail Zoom setting please refer to Page 19
Adjust the direction of flash
<S1/S2> Induction model
<M/Mulit> Manual fla sh /
Multiple frequency flash
High-speed synchronous
Second curtain sync
(Rear-curtain sync )
Buzzer switch
< >Flash exposure
<TTL>TTL mode
<E-TTL> Canon TTL mode
<i-TTL> Nikon mode
Power regulation
Power fine-tuning
Stroboscopic frequency setting
TTL exposure compensation
Light induction model
Custom function
Overheating protection
Aperture value
Frequency flash frequency
Power display
Manual zoom
Automatically zoom
Flash mode
SLAVE flash
<
> Channels
Zoom focal length
SLAVE mode
Flash light Ratio
SLAVE account
LCD screen
The flash head can be lifted up to 90 degrees, down to 7 degrees, and rotate up
to 180 degrees. Adjust the flash head toward the ceiling or wall can make the
shooting pictures more natural as well as pale shadows.
5
6
Applicable batteries and power supply.
Install the battery
The following batteries are applicable to the flash.
Lithium battery installation
1, AA battery
A:4 (AA) Alkaline manganese battery (1.5V). The battery can meet demand
of medium power without maintenance, but it can not be recharge.
B:4 (AA) Nickel-cadmium battery (1.2V). The battery recycles quickly and
can be recharged, so it is economic and practical.
1, Open the battery cover.
According to the direction of the
arrow shown in slide battery hatch
cover, open the battery compartment.
C:4 (AA) Nimh batteries (1.2V). This battery's power obviously exceed that
of nickel-cadmium battery and it is less harmful to the environment (do not
contain cadmium).
D:4 (AA) Lithium battery (1.5V). This battery has large capacity. Low
self-discharge rate and no need of maintenance.
E:4 (AA) Hydrogen oxygen cell (1.5V). This battery is also called (Oxyride),
Its capacity is larger and its service life is about 1.5 times of alkaline battery's.
So it is very Suitable for use in electronic products of high power consumption.
2, Install battery
According to the battery polarity
located on the indise of the battery
cover, install the battery into battery
compartment. Make sure the battery
polarity contact is correct.
3, Close the battery cover.
Closed it according to the direction
of the arrow shown in slide the
battery cover.
7
8
Install flash to camera
1.Prepare to install the fkash
According to the direction indicated by an
arrow will spin lock dial to the left side.
2.Install the flash
According to the direction indicated by an
arrow will flash installed foot completely
inserted into the camera's hot shoe.
3.Lock the flash
According to the direction indicated by an
arrow will spin lock dial to the right to lock
the flash.
Turn on the power
Press the Power button (ON/ OFF ) for
two seconds to turn on/off the flash.
orderto
tosave
savebattery
batterypower
power
avoid
battery
leakage,The
default
In order
andand
avoid
battery
leakage,The
default
settingsetting
is as
are as following:
follows:
After the DF3600U is turned on and there is no activity or no functions
working within 60 seconds,the CPU will go into Sleep Mode. In this case press
any button to wake up the flash. If the DF3600U is not used for a long period
time, it is recommended to use the main power switch to turn off the flash and
remove the power source (batteries). Before removing the batteries, turn off the
power of the DF3600U flash. After the DF3600U's capacitor is fully charged,
the DF3600U's flash ready indicator button ( ) lights up, indicating that the
flash is ready to trigger. This means that the DF3600U can be used for the next
shoot.
State of charge indicator
4.Remove the flash
According to the direction indicated by an
arrow will spin lock dial to the left side, and
slowly remove the flash from the hot shoe
Before shooting, confirm the flash charging
and camera viewfinder lights indicator lights
have been lit.
Make sure the flash and camera power are off.
Don't pull out forcibly!
9
External power supply by extending the interface and complete PC sync.
10
FEB setting value
Common flash mode
Divided into Automatic flash mode, TTL mode, M manual flash and
Stroboscopic flash mode Multi.
Automatic TTL flash mode
Set the camera's shooting mode to < P > (Program Auto Exposure) or Green
frame < □ > (Auto), fully Automatic flash will make flash photography and
modes of the < P > and < □ > as simple as Ordinary TTL Mode flash.
Select the flash mode
1.Press MODE flash mode select button in
common flash mode.
2.Press 【MODE】 mode button until the
LCD display
.
Set the flash exposure compensation value.
The exposure compensation can be set in standby
mode..
1, The Left and Right buttons set can set the exposure
compensation value:
Right Button: The exposure compensation is
increased; Left Button: The exposure compensation
value is decreased.
2, The compensation range can be set of -3.0EV to
+3.0EV.Its compensated value Icon:
By FEB you can stay under the condition of invariable background exposure
Automatically change the main body of the flash exposure. Surrounded by
three exposure can be adjusted according to 1/3 to plus or minus a level 3,
according to the lack of correct exposure, exposure and order of overexposed
exposure (Order by custom). In after completion of all three surrounded by
exposure, surrounded by flash exposure automatically cancel ( Non automati
cally canceled in the custom set ).
For flash surrounded the exposure function, set the camera driver Mode to "
single shot" and to ensure that the flash is ready before filming. Connect the
Canon camera, set on the flash exposure value surrounded exposure; Connection
Nikon, surrounded by not showing on the flash exposure information, if you need
to confirm the use of the camera support surrounded the exposure function, if
support, please refer to the camera set.
FEB setting surrounded by exposure value
( Effective for Canon cameras only )
Standby mode press “Parameter Settings button", surrounded by the current
exposure value, enter the set state.1, Surrounded by rotary dial can adjust
exposure valueClockwise rotation, surrounded by the exposure value, in turn,
increases; Counterclockwise, surrounded by the exposure value decreases in
turn.2, The exposure value range is 0 to 3.0. Surrounded by the exposure value
is: 0 1 1.3 1.7 2.0 0.3 0.7 2.3 2.7 3.0
0
0.3
0.7
1.0
1.3
1.7
2.0
2.3
2.7
3.0
0EV→+0.3EV→+0.7EV→+1.0EV→+1.3EV→+1.7EV→....→+3.0EV
0EV→-0.3EV→-0.7EV→-1.0EV→-1.3EV→-1.7EV→....→-3.0EV
11
12
3, Complete setup
After set up press again the【 Parameter Settings button 】to exit the set
status. If FEB value is not 0 displays, as shown by the custom function can
be set FEB exposure sequence.
On-line operation
Flash TTL mode
Through the hot shoe connection Canon camera;
Screen displays E-TTL to represent the current metering system;
Through the hot shoe connection Nikon camera;
Screen display i-TTL to represent the current metering system;
Because the Nikon system does not support flash on FEB Settings, while
online does not display the FEB information, to realize surrounded the
exposure function on Nikon (BKT), please refer to the camera Settings.
Flash exposure lock (FEL/FV)
Use flash exposure lock, you can lock the correct
flash exposure Settings for each parts of scene.
When flash TTL mode is displayed on the LCD
screen, please connect the flash with camera
correctly. Canon camera press the
" FEL" or "*" (AEL- Auto exposure lock) button,
Nikon Camera press "FV" button, Then the flash
give off preflash, camera will calculate the
appropriate flash output data, At this point you
have a time to re composition, After it finished you
can press the shutter to shooting.(This feature
requires to camer support to use.Please refer to
your camera manual set)
Other Automatic flash shooting mode
As long as the camera's shooting mode to (AV) or A (Aperture priority ae),
the [TV] S (Shutter priority ae) or [M] (Manual), you can also use E-TTL
/ i-TTL flash Automatically
Select this mode to manually set the shutter speed.Value is Automatically
set to match the camera shutter speed circle for standard exposure.If the
TV/S
aperture display flashing, means that the background underexposed or
overexposed, adjust the shutter speed until the aperture stop flashing.
AV/A
Select this mode to manually set the aperture value.The camera is
Automatically set to match the aperture shutter speed to achieve
standard exposure.If the dark background, such as at night), will use
the slow sync in order to obtain the main your subject and the
background of the standard exposure.Using flash for MASTER of your
subject standard exposure.Use the slow shutter background exposure
standards.Because for low illumination scene will use the slow shutter,
it is recommended to use a tripod.If the shutter speed display flashing,
means that the background underexposed or overexposed.Adjust the
display stops flashing until aperture shutter speed.
M
To manually set the shutter speed and aperture when choosing this pattern.
Using flash for MASTER of your subject standard exposure.Using a
combination of you to set the shutter speed and aperture to obtain
background exposure.
If you use the < DEP > or < A - DEP > shooting model, The result and use
< P > (AE) model is the same.
Flash Sync Speeds and Apertures Value.
P
Aperture Setting
Automatic
AV
Set Automatically(30 sec.~1/Xsec.)
Automatic
Manual
M
Set manually(buLb,30 sec.~1/Xsec.)
Manual
TV
13
Shutter Speed Setting
Set Automatically(1/60 sec.~1/Xsec.)
Set manually(30 sec.~1/Xsec.)
14
1/X sec.is the camera's maximum flash sync speed.
Note: The Canon camera mode: P, TV, AV, M, A - DEP, green frame
Nikon mode: P, S, A, M
Manual flash mode M
When you need to manually exposure, You can set the flash brightness
according to your own needs. From 1/128 power to 1/1 full power to adjust
the incremental setting the flash output.
more than 10 consecutive frequency glint light shoot. Between exposure
operation, please let the flash have enough time to call back. If you try to
execute more than 10 consecutive frequency glint light shoot. In order to
prevent flash unit overheating, flash can Automatically stop. If this situation
happened, please let flash cooling for at least 15 minutes.Please use a new
battery or the full battery operating this mode.
Select the flash mode
Press 【MODE】 button
until the LCD display
Select the flash MODE
1.Press 【 MODE】 button
2.until the LCD display M.
Power setting
Use the Left and Right buttons to manually
set output power value.The Left Button
will decrease down to 1/128 and the Right
Button will increase to 1/1 (full power).
The number of flashes set
Next, press the Settings/Select button and adjust the
number of flashes using the Left and Right buttons.
Depending on the Manual Power Ratio, you can
adjust the number of flashes from 1 to 40. Once you
have reached your desired number of flashes, press
the Settings/Select button to exit.
Right: 1/128 → 1 /64 →1 / 32 →11/ 16 → 1/8 → 1/4→ 1/2 → 1/1
Left : 1/ 1 → 1/2 →1 /4 → 1/8 → 1/ 16 → 1/32 → 1/64 → 1/128
Exposure power setting
Press the Setting/Select button again to delect the
power. Use the Left and Right buttons to choose from
1/128 power up to 1/4 power.
Stroboscopic flash mode(Multi)
To properly use Multi mode, set the camera in the M mode. When you using
the Multi mode, there will emit a series of quick flash, it can undertake
Multiple flash in a photograph, a series of actions in order to freeze.
Commonly used when shooting a moving object, Please set the flash output
power as required, Times of flash and Flash frequency (Every flashes time
show by Hz). Please use the new batteries or fully charged battery operating
this mode. To prevent flash unit overheating and damage, do not perform
15
.
Frequency setting
Press the Setting/Select Button and the Hz will
flicker. Adjust using the Left or Right buttons, then
press the Settings/Select button to set. You can adjust
the flash frequency from 1 Hz - 199 Hz.
The relational table of flash power and times of flash
Flash power
1/128
1/64
1/32
1/16
1/8
1/4
Times of flash
1-40
1-20
1-12
1-8
1-4
1-2
16
Note:
·Stroboscopic mode, Use the following formula to determine the shutter
speed, and then use the step is smaller than the shutter speed of one or
more long shutter speed.
·The shutter speed = Times of flash÷Flash frequency (Hz)
·The shutter speed, can be used with B door
“
”High speed “
” Rear-Curtain sync Settings
High-speed synchronous:
Synchronous operation of flash and camera with high shutter speed, The
maximum shutter speed of up to 1/8000s.When using a flash to shoot an
outdoor portrait, as well as other needs under the strong light source and
large aperture this mode is very excellent results.
Rear curtain sync:
Use the slow shutter, you can create a light trails after your subject, flash in
front of the shutter closes a flash.
1, Flash light to be on the Canon camera using
high speed/curtain sync correctly, in TTL, M
mode according to the 【 High speed/Rear
curtain/Ordinary flashlight switch button】
in ordinary flash (former curtain sync) (no),
display and high speed synchronization
between curtain sync (
) after (
)->
switch, open the corresponding function.
High-speed synchronization off the machine can be achieved in two
ways:
1, Wireless TTL trigger (The trigger need support high speed synchronization)
2, Set the speedlight to SLAVE c or SLAVE n mode
a:To achieve the High speed sync in SLAVE c, receiving Canon Wireless
instructions, first, the photograph in manual mode using built-in flash as the
Wireless MASTER flash, the maximum sync speed is only to 1 / 200 or 1 / 250.
Need in the set-top plus a band Wireless control function of the flash, in the
main control flash open high-speed synchronous, online MASTER light signal
from light, in order to achieve from the machine high speed sync to.
b: To achieve the High speed sync in SLAVE n, receiving the order of the Nikon
C can use built-in flash flash, can also use flash with MASTER control function,
open the camera Auto FP function, using the built-in flash flash, built-in flash
only send data to from the lamp, they do not sync in flash, by from the lamp to
carry out high-speed synchronous machine.
The camera menu access (Only the newest Canon Camera)
In support of E-TTL Canon is relatively new camera can be accessed through
the camera menu to operate on the flash.In flash control menu of "External
flash function settings" and "External flash custom function settings" can set
the flash related parameters, such as switch E-TTL mode, manual flash mode
and Multiple flash mode (Multi), Wireless flash setting, surrounded by
exposure, exposure compensation, the focal length and the function of advanced
options.
2, Flash on Nikon camera can not directly set high speed synchronous mode, the
camera menu of the Automatically "FP" is opened, connect the camera flash
screen display ," "immediately.
If you need the Rear-curtain synchronous mode,Open the Rear-curtain sync
function on the camera settings (Flash no display).
Off-camera high speed synchronous:
In Wireless SLAVE mode can receive high speed synchronous signal from
MASTER flash.
Note: In order to make correct use of high-speed/Rear-curtain sync, please
properly set camera flash mode and shutter speed.
17
18
【ZOOM】settings
Press ‘ZOOM button’ to display flicking. The flash will default to A
(Automatically zooms with the lens). To manually change to a different focal
length, press the Right Button to go to Manual, them continue pressing until
you reach the desired setting. Use the Left Button to decrease the focal length
and keep pressing until it goes back to A. Press "ZOOM button" to exit setup.
A
M
M
M
M
M
M
M
M
M
M
Automatic
18
24
28
35
50
70
85
105
135
180
Wireless command flash mode
Wireless flash system is composed by Multiple Wireless flash;You can
create a wide variety of lighting effects like using ordinary TTL flash.
Wireless command flash mode has SLAVE mode.
SLAVE flash mode.
SLAVE flash mode can be divided into:
Wireless SLAVE flash mode (E-TTL SLAVE c Canon)
Command SLAVE flash mode (i-TTL SLAVE n Nikon)
About Automatic Zoom A and Manual Zoom M Settings:
Flash head Automatically zoom: If the unit does
not default to "A" , continue to press the Left Button
until "A" is displayed and the flash will now
Automatically adjust the flash coverage with the
focal length of the lens up to 180mm when mounted
to cameras which support E -TTL and i-TTL
systems.
Manually set the lamp holder zoom position:
Press the Right Button when the "M" is displayed,
and then you can manually adjust the flash
coverage (18, 24, 28, 35, 50, 70, 85, 105, 135 or
180mm).
·When using manual zoom, please make sure that flash coverage equals
the lens zoom setting, so that the picture will not appear the edge of the
shadow.
SLAVE flash model
SLAVE flash model can be divided into:
Wireless instruction model (SLAVE c/SLAVE n )
Wireless optical flash model
Long press 【Flash model select button】 3 seconds ,flash light will shift
between flash model(TTL/M/Multi) and SLAVE flash model (E-TTL
SLAVE c /i-TTL SLAVE n ).
Under normal flash model : Long press 【Flash model select button】
3 seconds shift into wireless flash model.
Under Wireless flash model:Short press 【Flash model select button】
flash light shift between E-TTL SLAVE c model ,i-TTL SLAVE n model ,
M S1 model and M S2 model.
UnderSLAVE model :Long press 【Flash model select button】,it can
shift into flash mode (Salve C /SLAVE c /S1/S2 as off camera SLAVE
unit to build different light.
SLAVE c
19
SLAVE n
20
trigger to MASTER light.Before shooting ,we need set up the same channel
about flash light and MASTER light.
Short press (Zoom button): until channel or group twinkle as for SLAVE
unit ,setting Communication channel of SLAVE unit (1.2.3.4) and SLAVE
unit group (A.B.C)
S1
S2
Note:
1, Short press 【Flash model select button】 only change SLAVE flash model
in Wireless SLAVE flash model.If the flash is connected to the camera, press
the shutter button, the flash will not be connected with the camera, and it needs
to manually exit the wireless slave mode to perform the online operation.
2, Under SLAVE mode, you can through the custom function (Fn-08) on the
AF assist light flash close, exit wireless SLAVE mode, need to use the focus
lamp, please enter custom settings page to re open the AF assist lamp.
3, System standby 60 seconds after the flash will not enter the dormant state.
When working in a SLAVE unit, the flash light and mode are completely
controlled by the MASTER control unit and display the received
information;
Wireless instruction model (SLAVE c /SLAVE n )
SLAVE c: means receive Wireless flash sign from Canon 7D/60D/60c
camera bulid-in flash and 580EX II、600EX、ST-E2 and the Vice factory
MASTER wireless flash signal.
SLAVE n:means receive C instruction sign from Nikon camera bulid in
flash instruction and SB-900/800/700、SU-800 and the Vice factory
MASTER command signal signal
SLAVE c/n: support 4 channels ,3 different group ,TTL ,Manual and Multi
Wireless flash by this model.Rotate flash light head in order to wireless
21
Note:
·Flash light and model in Wireless instruction Parameter in Wireless
instruction mode can't setting directly.It's only can setting by
MASTER light.
·To correctly use the wireless command mode, you must setting
communication channel and group by correct.
22
Wireless optical flash model(S1,S2)
Rotating the flash lamp, the signal transmitter should toward to the
MASTER speedlight in S1, S2 mode.
Setting optical flash model:
1, Press 【Flash model select button】 until LCD display S1/S2 model in
Wireless flash model.These two models are suitable for the side effect of
the machine, to create a variety of lighting effects. They are suitable for
manual flash and TTL flash environment.
2, In these two modes, the output brightness is adjusted to the same as the
M mode.
S1 model:
Suitable for manual flash environment,each
flash of induction MASTER flash light and
sync trigger falsh.The effect as same as
Wireless flash trigger.MASTER flash setting
manual model in commom situation,please
don't use TTL model of pre-flash and red rey
reduction of several flash.
S2 model:
Suitable for manual flash environment
(pre-flash cancelmodel ).This model can
ignone TTL flash Pre flashing signal and main
flash sync.It support MASTER flash light in
TTL model.
Note: If SLAVE light does't sync flash with MASTER flash light in S1
/S2 model.Pleaes setting optcial model of SLAVE light and power
output by correct.
Please avoid several situation as below:
Avoid MASTER light to use red eye reduction funciton
Avoid MASTER light to use model lamp
Avoid MASTER light to use instruction model(Nikon) or wireless
model (Canon)
Avoid MASTER light to use ST-E2 and the vice factory master flash
as for flash controler.
23
Note:
If the camera without a built-in flash (such as Canon's 5D, 5D II, 5D III)
is unable to use the c/Slave n S1/S2 or Slave mode separately. Because the
Slave c/Slave n or S1/S2 mode is required to use the Master light exposure
to use. If you need to use this feature to you need repurchasing the original
Canon flash or ST-E2 as a flash controller.
Multi lighting applications
1, Wireless optical instrcution light
You can create two or three slave units to complete the multi - position
shooting requirement. And by the main TTL auto flash shooting flash
set the flash ratio, manual flash output strobe output,
(1)Flash light compose two salve unit group's wireless flash.
Setting SLAVE unit: SLAVE c and SLAVE n.
Setting channel: 1,2,3,4
Setting group: Two flash lights setting group A ,B
Setting MASTER unit: Setting each group flash model and output power
Setting flash light ratio: Setting MASTER unit flash light ratio A:B or A:
B:C for shooting (for example: Canon instruciton )
(2)Flash light compose three SLAVE unit group 's wireless flash
Setting SLAVE unit: SLAVE c and SLAVE n.
Setting channel: 1,2,3,4
Setting group: Three flash lights setting group A,B,C
Setting MASTER unit: Setting each group's flash model and output power
Setting flash light ratio: MASTER unit flash light ratio setting <A: BC>
(For example: Canon instruction ) ,press down test button of MASTER
unit to test flash.If the SLAVE unit doesn't flash ,please check the flash
light angle and the right distance.
Note:
MASTER unit: If setting <RATIO A: B>,setting SLAVE unit of group C
will not flash.
If the group of three flash light set <A>,they will be controlled by MASTER
flash light.
24
2, Wireless optical flash
Using built-in flash light or outlay flash light as MASTER MASTER flash
light.Please put different angel.
wireless channel will be reflect back by wall in indoor.So please choose
more space to put flash light.
After improved Wireless trigger inductor ,the trigger induction faster ,
S1 and S2 model availbe for outdoor.The distance 15 meters by wireless
trigger inductor.Put SLAVE light ,please test S1 or S2 whether is work
before shooting.
Note: Please don't put any barrier between MASTER flash light and
SLAVE flash light in optical flash.Wireless trigger induction to the
MASTER falsh light and don't allow the sunshine directly raying in
outdooor. If this request is not good for your shooting ,you can up or
down or left or right to roating the flash light.
Long press “customer menu setting key” to coustomer setting. The buzzer
switch will be ON or OFF.
1, A long ring: call back to complete
2, Two short ring: on or call back to complete normal flash.
3, Two long ring: flash call back unfinsihed.
4, Five short ring: the battery power is not enought or call back timeout.
5,Contiune buzz : flash ligve overheating and come into overheating
protection.The display will show icon.
Backlight display:
1, ON/OFF: Press the backlight button to change.
2, After standby 15s ,the backlight will be auto off.
Customer menu setting
Setting postion and operation rang
Outdoor
Indoor
Outdoor
Indoor
Voice prompts:
Different sound is different working conditions.
Updated: Year
Updated: Month
Updated: Date
25
26
According to your request to set up customer menu.
Automatic save function
Customer menu setting:Long press 【Customer menu button】” as left picture ;
Press <Parameter setting button) to select setting option.Rotary dial to setting
ON or OFF,then press 【Model flash select button】to quit.
After flash set up, 5 seconds without keystrokes, will automatically save
the current Settings, It is convenient for next time operation .
Setting clear
No
Fn-01
Fn-03
Fn-04
Function
Setting
NO.
Description
0
ON
1
OFF
0
ON
1
OFF
Auto sleep
Auto cancel
flash exposure
0
0→ -
1
-
When you need to clear the changes on the flash, restore the factory default
settings, just at the same time hold down the "parameter settings button" and
"High speed /Rear curtain/Ordinary flashlight switch button, the flash to
restore the default Settings.
Preset at the same time
→+
Flash exposure order
→ 0→ +
Flash lock (Low power tips)
Fn-08
Fn-14
Fn-15
Auto focus assisant flash
0
ON
1
OFF
0
ON
1
OFF
F
Date
Buzz switch
Version
When the battery power is low or other reasons cause flash charging is not
completed within the limit time, the flash will enter a state of lock, Mean
while the screen display as shown in figure, short channel with a buzzer
sounded, remind the user to replace the battery to ensure the normal use,
if change after fully charged batteries, flash light can't recycle back in a
limited amount of time (20 seconds) to recycle back, please contact after
sell service.
Note: Fn ON: 00-13 option by outlay flash light customer menu of camera
menu to setting. No: 00、02、05、06、07、09、10、11、12、13 option had
been ON(Canon inside menu)
27
28
Bounce Flash
Use the built-in wide-angle diffuser
Reflection flash is by putting a flash head toward the wall or ceiling, flash
be metope reflect in front of the illuminated by the object. This can reduce
the shadow on the reverse of the subject object, in order to obtain more
natural photographic effect.
When the camera to the subject's distance is less than 2m, you can use the
wide angle diffuser plate more naturally close-up. Can also use the built-in
wide-angle diffuser will flash coverage expanded into a wide angle.
Adjust the flash head tilt, rotation Angle and select the reflection
plane
When the flash head thrown back and
White Ceiling
the ceiling as the radiation surface,
can usually be the most simple to
obtain good results. Holding camera
longitudinal, horizontal select flash
can obtain the same effect.
Note that do not flash direct exposure
to the subject. Between flash head and
reflection plane .The effective distance is 1 m to 2 m, depending on the
shooting environment. Shoot color photos, please choose white or
reflective plane reflection flash. Otherwise,When taken photos will
appear unnatural color.
1.Pull out wide diffusion plate
Slowly pull completely wide diffusion
plate, then put it in the flash head.
2.Push the reflector plate
At the same time to push reflection piece
into the flash head.
Use the built-in reflex plate
Application of reflex flash when
shooting, use the built-in reflection
board, can make the main body more
bright and existence of vitality.
Meanwhile it can avoid to light the
front of the foreground objects.
1, The flash head up
90 degrees.
2, Pull out wide
diffusion plate as
well as pop-up
reflection card at
the same time.
3,Keep reflecting
cards with wide
diffusion plate, only
push wide diffusion
plate
29
30
Specification
Circuit design: Insulated gate bipolar transistor (IGBT)
Guide Number: 118 (ISO100,180 mm)
Flash coverage: Manual/Automatic zoom18 ~ 180 mm
Flash head rotation to achieve reflection flash
TTL flash mode: Automatic mode, Manual mode M, Stroboscopic mode
Multi, LED lighting, canon master,Nikon Master models,
Slave light SLAVE c, SLAVE n, Light flash mode S1, S2,
Surrounded by flash exposure (FEB)
Wireless trigger: Light pulse, Induction flash light
Wireless flash distance: Indoor 20 ~ 30 meters, Outdoor 10 ~ 15 m
Support the subordinate unit: 4 communication channels (1, 2, 3, 4) and
3 SLAVE unit group (A, B, C)
Rotation Angle: Up and Down - 7 ~ 90 degrees
Left-Right /Right-Left rotation Angle: 0 ~ 180 degrees
Color temperature :5500K
Flash time: 1/200s-1/20000s
Manual flash control: 1/128-1/1 step 0.3 EV, a total of 22 grade fine-tune
gear
External interface: Hot Shoe, PC sync interface, External interface DC
power supply
Recycle time : 2.3 seconds
Power supply: 4 AA Batteries,
Flashes :(A set of full working hours when the maximum and minimum
power battery) Flash number for 500-5000 times
Additional features: Power saving mode, Overheating protection
Size : 7.87" H x 2.95" W x 2.24" D
Weight : 13.2 oz. (without batteries)
31
Sunpak One Year Warranty:
This Sunpak product has been carefully manufactured, accurately adjusted,
inspected and thoroughly tested before shipment to assure you of the highest
quality. Should this Sunpak product require service, we will repair or
replace, at our option, any part, or the product itself, which our examination
shows to be defective in material or workmanship. This warranty does not
apply to wear and tear associated with the normal use of the product. This
warranty is non-transferable.
Repairs will be made to the product at no charge, under the terms of the
warranty as stated above, only when accompanied by a copy of your dated
and itemized sales receipt. Be certain to follow all assembly and/or operating
instruction with this product.
This warranty is not valid if the product has been misused or damaged in any
way that is beyond our control or through normal wear and tear associated
with its use. This warranty only applies to the product and we are not
responsible in any way for losses, damages or any inconvenience caused by
equipment failure.
Some states do not allow the exclusion or limitation of consequential
damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights and you may have other rights which
may vary from state to state.
Should service be required, the product should be carefully packed and sent
pre-paid and insured to the address listed below. A note describing the nature
of the defect should be enclosed to expedite handling. Proof of purchase
must be included for all warranty repairs.
32
Download PDF