CD Soundmachine AZ1300 AZ1305

AZ1300
AZ1305
CD Soundmachine
all versions
TABLE OF CONTENTS
Handling Chip Components and Safety ..........................1 - 1
Technical Specification & Service tools...........................2 - 1
Service Measurement......................................................2 - 2
Connections and controls.......................................3 - 1..3 - 2
Disassembly Diagram......................................................4 - 1
Block Diagram .................................................................5 - 1
Wiring Diagram................................................................6 - 1
Layout Diagram
Main Board
copper side .............................................................9 - 1
componet side ........................................................9 - 2
MCU Board
copper side ...........................................................10 - 1
component side ....................................................10 - 2
Exploded view - cabinet.................................................11 - 1
Mechanical partslist .......................................................12 - 1
Electrical partslist ...............................................12 - 1..12 - 2
Circuit diagram
Main Board
AF part ....................................................................7 - 1
CD part ...................................................................7 - 2
Tuner Board............................................................7 - 3
MCU Board ................................................................8 - 1
© Copyright
2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
CLASS 1
LASER PRODUCT
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
or otherwise without the prior permission of Philips.
Published by LX 0311 Service Audio
Printed in The Netherlands
Subject to modification
© 3140 785 32350
1-1
HANDLING CHIP COMPONENTS
©
WARNING
ESD
All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handling during
repair can reduce life drastically.
When repairing, make sure that you are connected with the
same potential as the mass of the set via a wristband with
resistance. Keep components and tools at this potential.
f
ATTENTION
Tous les IC et beaucoup d´autres semi-conducteurs sont
sensibles aux décharges statiques (ESD). Leur longévite
pourrait être considérablement écourtée par le fait qu´aucune
précaution nést prise à leur manipulation.
Lors de réparations, s´assurer de bien être relié au même
potentiel que la masse de l´appareil et enfileer le bracelet
serti d´une résistance de sécurité.
Veiller à ce que les composants ainsi que les outils que l´on
utilise soient également à ce potentiel.
d
WARNUNG
Alle ICs und viele andere Halbleiter sind empfindlich
gegenüber elektrostatischen Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kann die
Lebensdauer drastisch reduzieren.
Sorgen Sie dafür, daß Sie im Reparaturfall über ein Pulsarmband mit Widerstand mit dem Massepotential des
Gerätes verbunden sind.
Halten Sie Bauteile und Hilfsmittel ebenfalls auf diesem
Potential.
SAFETY
©
Safety regulations require that the set be restored to its
original condition and that parts which are identical with
those specified be used.
Safety components are marked by the symbol
WAARSCHUWING
Alle IC´s en vele andere halfgeleiders zijn gevoelig voor
electrostatische ontladingen (ESD).
Onzorgvuldig behandelen tijdens reparatie kan de levensduur
drastisch doen vermindern. Zorg ervoor dat u tijdens reparatie
via een polsband met weerstand verbonden bent met hetzelfde
potentiaal als de massa van het apparaat.
Houd componenten en hulpmiddelen ook op ditzelfde potentiaal.
i
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono sensibili alle scariche
statiche (ESD).
La loro longevità potrebbe essere fortemente ridatta in caso di
non osservazione della più grande cauzione alla loro
manipolazione. Durante le riparationi occorre quindi essere
collegato allo stesso potenziale che quello della massa
delápparecchio tramite un braccialetto a resistenza.
Assicurarsi che i componenti e anche gli utensili con quali si
lavora siano anche a questo potenziale.
ñ
Veiligheidsbepalingen vereisen, dat het apparaat in zijn
oorspronkeliijke toestand wordt teruggebracht en dat
onderdelen, identiek aan de gespecificeerde, worden toegepast.
De Veiligheidsonderdelen zijn aangeduid met het symbool
f
i
Les normes de sécurité exigent que l`appareil soit remis
à l`état d`origine et que soient utilisées les pièces de
rechange identiques à celles spécifiées.
Les composants de sécurité sont marqués
©
ñ
DANGER: Invisible laser radiation when open.
AVOID DIRECT EXPOSURE TO BEAM.
Le norme di sicurezza estigono che l´apparecchio venga
rimesso nelle condizioni originali e che siano utilizzati i
Bei jeder Reparatur sind die geltenden Sicherheitsvorpezzi di ricambiago identici a quelli specificati.
schriften zu beachten. Der Originalzustand des Gerätes
Componenty di sicurezza sono marcati con
darf nicht verändert werden. Für Reparaturen sind Originalersatzteile zu verwenden.
Sicherheitsbauteile sind durch das Symbol
markiert.
d
CLASS 1
LASER PRODUCT
s Varning !
Osynlig laserstrålning när apparaten är öppnad och
spärren är urkopplad. Betrakta ej strålen.
©
After servicing and before returning the set to customer
perform a leakage current measurement test from all
exposed metal parts to earth ground, to assure no
shock hazard exists.
The leakage current must not exceed 0.5mA.
∂ Advarsel !
ß Varoitus !
f
Usynlig laserstråling ved åbning når sikkerhedsafbrydere
er ude af funktion. Undgå udsaettelse for stråling.
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen !
"Pour votre sécurite, ces documents doivent être utilisés par
des spécialistes agréés, seuls habilités à réparer votre
appareil en panne".
2-1
TECHANICAL SPECIFICATIONS
GENERAL
Mains voltage
Mains frequency
Battery
Power consumption
Dimension (L x D x H)
Weight
TUNER - MW SECTION
-/00/05
-/17
-/00/05
-/17
mains
:
:
:
:
:
:
:
:
230 V
120 V
50 Hz
60 Hz
9 V (R14 x 6)
< 5 W typ.
360 x 225 x 152 mm
2.3 Kg
Tuning range
IF frequency
Sensitivity
Selectivity
IF rejection ratio
Image rejection ratio
Speaker impedance
Frequency response
520 - 1602 kHz
530 - 1700 kHz
450 kHz ± 1 kHz
< 5000 µV/m at 26dB S/N
> 16 dB
> 24 dB
> 28 dB
AUDIO CASSETTE RECORDER
AMPLIFIER
Output power
:
-/17 :
:
:
:
:
:
mains : 2 x 1 W
battery : 2 x 1 W
: 2 x 8 ohm
: 100 Hz -10 kHz (±2dB)
Number of tracks
Tape speed
Wow & flutter
Fast wind/rewind C60
Frequency response
S/N ratio
:
:
:
:
P/B :
:
1 stereo
4.76 cm/sec ± 3%
< 0.35 % JIS UWTD
< 130 sec.
125 - 8000 Hz
> 36 dB
TUNER - FM SECTION
COMPACT DISC
Tuning range
IF frequency
Sensitivity
Selectivity
IF rejection
Image rejection
:
:
:
:
:
:
87.5 - 108 MHz
10.7 MHz ±0.2MHz
< 22 dBf at 26dB S/N
> 20 dB at ±300kHz
> 50 dB
> 20 dB
S/N ratio
Channel difference
Channel crosstalk
Laser wavelength
Laser light power
: > 50 dB
1 kHz : < 3 dB
1 kHz : > 26 dB
: 780 ± 20nm
: < 0.3 mW
SERVICE TOOLS
Audio signal disc SBC 429.......................................................................4822 397 30184
Playability test disc SBC 444...................................................................4822 397 30245
Test disc 5 (disc without errors ) +
Test disc 5A (disc with dropout errors, black spots and fingerprints)
SBC 426/426A .....................................................................4822 397 30096
Burn in test disc (65 min. 1kHz signal at -30 dB level without “pause”) .....4822 397 30155
AVAILABLE ESD PROTECTION EQUIPMENT
anti-static table mat
large 1200x650x1.25mm
small 600x650x1.25m
anti-static wristband
connection box (3 press stud connections, 1MΩ)
extendible cable (2m, 2MΩ, to connect wristband to connection box)
connecting cable (3m, 2MΩ, to connect table mat to connection box)
earth cable (1MΩ, to connect any product to mat or to connection box)
KIT ESD3 (combining all 6 prior products - small table mat)
wristband tester
4822 466 10953
4822 466 10958
4822 395 10223
4822 320 11307
4822 320 11305
4822 320 11306
4822 320 11308
4822 310 10671
4822 344 13999
2-2
SERVICE MEASUREMENT
Tuner SW
Aerial replacement
Capacitor
RF Generator
Bandpass
250Hz-15kHz
LF Voltmeter
e.g. PM2534
e.g. 7122 707 48001
R=50Ω
Ri=50Ω
e.g. PM5326
DUT
S/N and distortion meter
e.g. Sound Technology ST1700B
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday«s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
Tuner AM (MW,LW)
DUT
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
RF Generator
e.g. PM5326
S/N and distortion meter
Ri=50Ω
e.g. Sound Technology ST1700B
Frame aerial
e.g. 7122 707 89001
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday«s cage.
CD
Use Audio Signal Disc SBC429 4822 397 30184 (replaces test disc 3)
L.P.F. = 13 th order filter 4822 395 30204
Low pass filter 22kHz
DUT
L
R
S/N and distortion meter
e.g. Sound Technology ST1700B
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
3-1
CONNECTIONS AND CONTROLS
1
9
8
9
7
2
6
3
REPEAT
VOLUME
SHUFFLE
8
7
0
SEARCH
4
+
-
PRESET
6
AC M AI N S ~
1
2
3
4
SEARCH
TUNING
5
!
5
Remote Control for
AZ1305 model only
English
CONTROL
POWER SUPPLY
ACCESSORIES
1 x AC mains lead
1 x Remote Control (for AZ1305 model only)
REMOTE CONTROL (for AZ1305 model only)
IMPORTANT!
• Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or cause
the batteries to burst.
• Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the
set.
• When inserting new batteries, do not try to mix old
batteries with the new ones.
• Batteries contain chemical substances, so
they should be disposed of properly.
TOP AND FRONT PANEL (See 1)
1 LIFT TO OPEN - lift here to open CD door.
2 PROG
CD: - programs tracks and reviews the program;
Tuner: - programs preset radio stations.
3 MODE - selects different play modes: e.g. REPEAT
or SHUFFLE (random) order.
4 VOLUME 3 , 4 - to adjust volume level.
-
PRESET + , (up, down) - selects a preset radio
station.
5 Display - shows the status of the set.
6 2; - starts or pauses CD playback.
9 - to stop playback or erase a CD program.
SEARCH § , §
CD: - searches backward and forward within a track;
- skips to the beginning of a current track/
previous/ later track.
1
2
3
4
5
6
7
8
VOLUME 3 , 4 - adjusts volume level.
SHUFFLE - plays all CD tracks in random order.
2; - starts or pauses CD playback.
SEARCH 5 , 6 - searches backwards/
forwards within a track.
PRESET + , (up, down) - selects a preset radio
station.
TUNING § , § (down, up) - tunes to tuner stations.
9 - to stop playback;
- erases a CD program.
¡ , ™ - skips to the beginning of a current track
-
previous/ subsequent track.
9 REPEAT - repeats a track /program/ entire CD.
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
Using AC Power
1. Check if the AC power supply, as shown on the
type plate located on the bottom of the set,
corresponds to your local power supply. If it does
not, consult your dealer or service centre.
2. Connect the mains lead to the wall socket.
3. To disconnect the mains supply, unplug the set
from the wall socket.
This set complies with the radio interference
requirements of the European Community.
RADIO: - (down, up) tunes to radio stations.
7 DBB (Dynamic Bass Boost) - activates a more vivid
bass response.
POWER SUPPLY
Whenever convenient, use the AC power supply to
conserve battery life. Make sure you remove the
8 POWER slider - selects CD/ MW / FM / OFF
function and also the power off switch (OFF).
power plug from the set and wall outlet before
inserting batteries.
BASIC FUNCTIONS
BACK PANEL (See 1)
9 Telescopic aerial - improves FM reception.
Batteries (not included)
• Insert 6 batteries, type R-14, UM-2 or C-cells,
Switching on and off and selecting function
1. To switch on, adjust the POWER slider to select:
CD, MW (AM), FM function, and operate the
0 Battery compartment - for 6 batteries, type
R-14, UM2 or C-cells.
! AC MAINS - inlet for mains lead.
(preferably alkaline) with the correct polarity. (See 6)
• Remote control (AZ1305 model only)
Insert 2 batteries, type AAA, R03 or UM4
(preferably alkaline). (See 8)
For users in the U.K., please follow the boxed
instructions ‘Important notes...’ on this sheet.
respective function controls.
2. To switch off, adjust the POWER slider to select
OFF .
Note : The DBB setting, tuner presets and the
volume level (maximum to 20) will be retained in the
set's memory.
Adjusting volume and sound (See 2)
1. Adjust the volume with the VOLUME controls.
™ Display shows the volume level in number from
0-32.
2. Press DBB once or more to select dynamic bass
boost on or off.
™ Display: shows
when activated.
3-2
CONNECTIONS AND CONTROLS
DIGITAL TUNER
DIGITAL TUNER
Tuning to radio stations
1. Adjust the POWER slider to MW or FM.
™ The radio. station frequency, waveband are
shown (See 3)
2. Press and hold SEARCH § or § until the
frequency in the display starts running.
™ The radio automatically tunes to a station of
sufficient reception. Display shows Srch
during automatic tuning.
3. Repeat step 2 if necessary until you find the
desired station.
• To tune to a weak station, press § or § briefly
and repeatedly until you have found optimal
reception.
To improve radio reception:
• For FM, extend, incline and turn the telescopic
aerial. Reduce its length if the signal is too strong.
• For MW , the set uses a built-in aerial. Direct this
aerial by turning the whole set.
Programming radio stations
You can store up to a total of 30 radio stations (20 FM
and 10 MW) in the memory, manually or automatically
(Autostore).
DIGITAL TUNER
CD PLAYER
CD PLAYER
Manual programming
1. Tune to your desired station (see Tuning to radio
stations).
Playing a CD
This CD player plays Audio Discs including CDRecordables and CD-Rewritables.
Finding a passage within a track
1. Press and hold SEARCH § or §.
– The CD is played at high speed and low volume.
2. Press PROG to activate programming.
™ PROG flashes.
3. Press PRESET + / once or more to select a
preset number.
• Remote control (AZ1305 models only): Press
PRESET + / once or more to select a preset
station.
4. Press PROG to confirm.
5. Repeat steps 1-4 to store other stations.
1. Adjust the POWER slider to CD.
2. Open the CD Door.
™ OPEN is displayed.
3. Insert a CD with the printed side facing up and
close the door.
™ nocd if no CD inserted/ CD dirty, incorrectly
inserted or damaged.
™ nFcd if you have inserted a non-finalized CDR(W).
4. Press 2; to start playback.
™ dAtA if your CD contains non-audio i.e. data
files.
5. To pause playback press 2;. Press 2; again to
resume play.
™ Display: 1 flashes during pause.
6. To stop CD playback, press the 9 button.
2. When you recognize the passage you want,
release § or § to resume normal playback.
Note : During a CD program or if SHUFFLE/
REPEAT active, searching is only possible within a
track.
-
-
Note : You can erase a preset station by storing
another frequency in its place.
Autostore
Autostore automatically starts programming radio
stations from preset 1. Available stations are
programmed in order if the station with sufficient
reception strength. Any previous presets e.g. manually
programmed will be erased.
• Press PROG for 2 seconds or more to activate
autostore programming.
™ The display shows AUtO, PROG blinks,
followed by the radio station details when
stored.
After all stations are stored, the first preset station
will then automatically play.
Note : CD play will also stop when:
- the CD door is opened
- the CD has reached the end
- you select MW / FM function.
Selecting a different track
• Press SEARCH § or § once or repeatedly to
select your track.
• In the pause / stop position, press.2; to start
Different play modes: SHUFFLE and REPEAT
You can select and change the various play modes
before or during playback, and combine the modes
with PROG. (See 4)
(SHUFFLE) - tracks of the entire CD/ program
are played in random order
(SHUFFLE REPEAT ALL) - to repeat the
entire CD/ program continuously in random order
(REPEAT ALL) - repeats the entire CD/
program
(REPEAT) - plays the current track continuously
1. To select play mode, press MODE once or more.
2. Press 2; to start playback if in the stop position.
3. To select normal playback, press MODE
repeatedly until the various modes are no longer
displayed.
– You can also press the 9 button to cancel your
play mode.
playback.
To listen to a preset station
• Press the PRESET + , buttons once or more until
-
the desired preset station is displayed.
• Remote control (AZ1305 models only): optionally,
press PRESET + , to select your preset station.
-
CD PLAYER
SAFETY & MAINTENANCE
Programming track numbers
In the stop position, select and store your CD tracks in
the desired sequence. Up to 20 tracks can be stored in
the memory.
1. Press SEARCH § or § on the set to select your
SAFETY & MAINTENANCE INFORMATION
(See 7)
• Don't expose the set, batteries, CDs to humidity,
rain, sand or excessive heat.
desired track number.
2. Press PROG.
™ Display: PROG, Prog briefly and your
selected track number. (See 5)
™ If you attempt to program without first
selecting a track number, noSE is shown.
3. Repeat steps 1-2 to select and store all desired
tracks.
™ Display: FULL if you try to program more
than 20 tracks.
Reviewing the program
In the stop position, press and hold PROG until the
display shows all your stored track numbers in
sequence.
cleaning agents containing alcohol, ammonia,
benzene or abrasives as these may harm the set.
• Place the set on a hard and flat surface so that the
system does not tilt. Make sure there is good
™ CLr is displayed briefly and PROG
disappears.
• You select MW / FM function.
• Open the CD door.
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING: Do not open the set as there is a risk of electric shock! Under no
circumstances should you try to repair the set yourself, as this will
invalidate the guarantee.
• Clean the set with a dry cloth. Don't use any
ventilation to prevent the set overheating.
• The mechanical parts of the set contain
self-lubricating bearings and must not be oiled or
lubricated.
CD player and CD handling
• If the CD player cannot read CDs correctly, use a
cleaning CD to clean the lens before taking the set
to repair.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature
Erasing a program
You can erase the program by either:
• pressing 9 twice
TROUBLESHOOTING
can cause condensation on the lens of your CD
player. Playing a CD is then not possible. Do not
attempt to clean the lens but leave the set in a
warm environment until the moisture evaporates.
• Always close the CD door to avoid dust on the lens.
• To clean the CD, wipe in a straight line from the
centre towards the edge using a soft, lint-free
cloth. Do not use cleaning agents as they may
damage the disc.
No sound /power
–
•
–
•
–
•
Volume not adjusted
Adjust the VOLUME
Mains lead not securely connected
Connect the AC mains lead properly
Batteries exhausted/ incorrectly inserted
Insert (fresh) batteries correctly
Severe radio hum or noise
– Electrical interference: set too close to TV, VCR or
computer
• Move the set to increase the distance
Poor radio reception
– Weak radio signal
• FM: Adjust the FM telescopic aerial
nocd indication
–
•
–
•
dAtA indication
– CD contains non-audio files
• Press SEARCH § or § once or more to skip to a
CD audio track, instead of the data file
The CD skips tracks
–
•
–
•
CD damaged or dirty
Replace or clean CD
SHUFFLE or PROG is active
Switch off SHUFFLE / PROG
Remote control does not function properly (for
AZ1305 model only)
–
•
–
•
Batteries exhausted/ incorrectly inserted
Insert (fresh) batteries correctly
Distance/ angle between the set too large
Reduce the distance/ angle
CD badly scratched or dirty
Replace/ clean CD, see Maintenance
Laser lens steamed up
Wait until lens has cleared
nFcd indication
– CD-R(W) is blank/ not finalized
• Use a finalized CD-R(W)
• Never write on a CD or attach any stickers to it.
Environmental information
We have done our best to reduce the packaging and make it easy to separate into 3 materials:
cardboard, expandable polystyrene, polyethylene.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packaging, exhausted batteries and old equipment.
For more information on operation instruction please visit Philips Audio internet site :
http://www.audio.philips.com
4-1
4-1
DISASSEMBLY DIAGRAM
A. REMOVE FRONT CABINET ASSEMBLY
C. REMOVE DECK MECHANISM
- REMOVE SCREWS A1 (3X20) 6 PCS.
- REMOVE SCREWS C4 (2.5X8) 6 PCS.
- REMOVE SCREW A2 (3X55) 1 PC
- REMOVE MAIN BOARD
(INSIDE BATTERY COMPARTMENT)
- REMOVE SCREWS C5 (2.5X10) 4 PCS.
- REVOVE CD DECK
A2 (x1)
A1 (x6)
C5 (x4)
C4 (x6)
B. REMOVE BOTTOM CABINET ASSEMBLY
- REMOVE SCREWS B3 (3X8) 2 PCS.
D. REMOVE FRONT PANEL
- REMOVE SCREWS D6 (2.5X10) 8 PCS.
- REMOVE SCREWS D7 (2.5X8) 6 PCS.
D6 (x8)
D7 (x6)
B3 (x2)
5-1
BLOCK DIAGRAM
5-1
6-1
6-1
WIRING DIAGRAM
1P UL1007 28AW WIRE 120MM
1P UL1007 28AW WIRE 80MM
BATT-
VCC
GND
BATTRY 9V (1.5X6)
BATT+
2P HOUSING ASS'Y 220MM
AC1 AC2
3P FLAT WIRE WIRE
13P FFC WIRE 400MM
6P HOUING ASS'Y 120MM
5P FFC WIRE 230MM
FM ANT.
1P UL1007 26AW WIRE 160MM
LEFT
GND
RIGHT
VCC
GND
ENABL
CLOCK
STEREO
ECO-06
MW ANT.
1PX2 UL1007 26AW WIRE 80MM
CPU - KEY PCB
4P FFC WIRE 100MM
LCH OUT
GND
RCH OUT
MOTHER BOARD
SPEAKER PCB
LSP
3P HUSING WAFER 300MMX2+550MM
ASP
1P UL1007 26AW WIRE 80MM
AC SOCKET
(AC/BATT.CON.SW)
TRANSFORMER
16P FFC WIRE 100MM
7-1
for AZ1310 only
CIRCUIT DIAGRAM - MAIN BOARD
(AF PART)
7-1
7-2
CIRCUIT DIAGRAM - MAIN BOARD
(CD PART)
7-2
7-3
CIRCUIT DIAGRAM - TUNER BOARD
7-3
8-1
CIRCUIT DIAGRAM - MCU BOARD
8-1
9-1
LAYOUT DIAGRAM - MAIN BOARD
(COPPER SIDE VIEW)
9-1
9-2
LAYOUT DIAGRAM - MAIN BOARD
(COMPONENT SIDE VIEW)
9-2
10 - 1
LAYOUT DIAGRAM- MCU BOARD
(COPPER SIDE VIEW)
10 - 1
10 - 2
LAYOUT DIAGRAM - MCU BOARD
(COMPONENT SIDE VIEW)
10 - 2
11 - 1
11 - 1
EXPLODED VIEW DIAGRAM - CABINET
SCREW LIST :
1
2
3
4
5
6
7
8
9
0
!
@
#
M3x6
T2 x 8
434
T2.5 x 10
438
T3 x 10
7 (1x)
T3 x 12
433
T3 x 16
439
T3 x 20
T3 x 32
M3x55 (1x)
C P/W 2.5 x 10
9 (6x)
432
T P/W 3 x 10
441
7 (2x)
T P/W 3 x 16
442
443
444
7 (4x)
7 (2x)
6 (8x)
429
428
5 (2x)
! (1x) 427
426
7 (4x)
424
417
412
413
414
416
! (4x)
3 (6x)
422
418
421
3 (1x)
404
407
408
409
411
406
403
402
437
5 (2x)
T3 x 8
431
401
9 (2x)
436
T2.5 x 8
7 (6x)
419
423
3 (4x)
12 - 1
12 - 1
MECHANICAL PARTSLIST
ELECTRICAL PARTSLIST
401
402
403
404
406
9965 000 16941
9965 000 16947
9965 000 16946
9965 000 16945
9965 000 16940
DISPLAY LENS
PC MAGIC MIRROR
COSMETIC DISC (R)
COSMETIC DISC (L)
FRONT PANEL
- MISCELLANEOUS -
407
408
409
411
412
9965 000 16855
9965 000 16856
9965 000 16857
9965 000 16858
9965 000 16860
VOLUME KNOB - (UP)
VOLUME KNOB - (DOWN)
PRESET KNOB - (UP)
PRESET KNOB - (DOWN)
PREVIOUS KNOB
413
414
416
417
418
9965 000 16861
9965 000 16862
9965 000 16948
9965 000 16950
9965 000 16949
STOP KNOB
NEXT KNOB
PLAY KNOB
DBB KNOB
MODE/PROGRAM KNOB
419
421
422
423
424
9965 000 16938
9965 000 16883
9965 000 16884
9965 000 16882
9965 000 16881
FRONT CABINET
CUSHION 658PH (GREY)
CD DECK TCP11TM2P
CUSHION 658PG (BLACK)
DUST COVER SK-02
426
427
428
429
431
9965 000 16870
9965 000 16850
9965 000 16875
9965 000 16849
9965 000 16955
DAMPER HOLDER BRACKET
CD DOOR GEAR
CD DOOR SPRING
FUNCTION KNOB ADAPTOR
CD TRAY (-/17)
431
432
433
434
436
9965 000 16944
9965 000 16859
9965 000 16943
9965 000 16939
9965 000 16854
CD TRAY
FUNCTION KNOB
CD DOOR
BOTTOM CABINET
HANDLE HINGE - (R)
437
438
439
441
442
9965 000 16841
9965 000 16853
9965 000 16871
9965 000 16873
9965 000 16942
HANDLE
HANDLE HINGE - (L)
ANTENNA CONTACT PLATE
BATTERY SPRING - (-)
BATTERY DOOR
443
444
9965 000 16872
9965 000 16874
9965 000 17018
9965 000 16956
BATTERY CONTACT PLATE - (+)
BATTERY SPRING - (+-)
REMOTE CONTROL RC19414002
LEAFLET (-/17)
Note: Only these parts mentioned in the list are
normal service parts.
- DIODES -
1106
SW01
SW02
SW1
9965 000 16396
9965 000 16886
9965 000 16887
9965 000 16888
9965 000 13705
ROD ANTENNA
FERRITE BAR
BAND SWITCH
DETECTOR SWITCH
TACT-SWITCH
6103
6105
6130
6131
6181
5322 130 34337
9965 000 07240
9965 000 16914
9965 000 16914
5322 130 34337
BAV99
HN1V02H
ISV228
ISV228
BAV99
SW2
SW3
SW4
SW5
SW6
9965 000 13705
9965 000 16889
9965 000 16889
9965 000 13705
9965 000 13705
TACT-SWITCH
TACT-SWITCH
TACT-SWITCH
TACT-SWITCH
TACT-SWITCH
6182
6183
D601
D602
D603
9340 255 30135
9340 386 90115
5322 130 34337
5322 130 34337
9340 255 30135
BAS216
BZX284-C11
BAV99
BAV99
BAS216
SW7
SW8
SW9
SW10
SW11
9965 000 13705
9965 000 13705
9965 000 13705
9965 000 13705
9965 000 13705
TACT-SWITCH
TACT-SWITCH
TACT-SWITCH
TACT-SWITCH
TACT-SWITCH
D604
D605
D606
D702
D801
9965 000 16915
9965 000 16915
5322 130 34337
9965 000 16915
9965 000 16916
HZ4B2
HZ4B2
BAV99
HZ4B2
DIODE 6,2V
9322 155 82667
9965 000 16891
9965 000 16892
9965 000 16894
9965 000 16895
IR RECEIVER
FERRITE BEAD
FFC CABLE WIRE 13P
FFC CABLE WIRE 4P
FFC CABLE WIRE 5P
D802
D803
D804
D805
D810
9965 000 16917
4822 130 30621
4822 130 30621
9965 000 16918
4822 130 30621
DIODE 5,6V
1N4148
1N4148
4,7V 1/2W
1N4148
9965 000 16954
9965 000 16957
9965 000 16958
2422 070 98152
SPEAKER 4" 8 OHM 3W
TRANSFORMER
AC SOCKET
MAINSCORD 1,79MHz
D812
D814
D816
D817
D819
4822 130 30621
4822 130 30621
4822 130 30621
4822 130 30621
4822 130 30621
1N4148
1N4148
1N4148
1N4148
1N4148
D835
D836
D837
D838
D840
4822 130 31438
4822 130 31438
4822 130 31438
4822 130 31438
9965 000 16916
1N4001G
1N4001G
1N4001G
1N4001G
DIODE 6,2V
DISP
9965 000 16919
LED DISPLAY
- CAPACITORS AND RESISTERS3142
2155
2106
9965 000 16900
4822 125 11113
9965 000 16901
SEMI-FIXED 100KB
TRIM CAPACITOR
TRIMMER CVN620
- COILS & FILTERS -
- IC & TRANSISTORS -
5104
5109
5110
5111
5112
9965 000 16902
9965 000 16903
9965 000 16903
9965 000 16904
9965 000 16905
AM COIL AN75-871390
10,7MHZ MS3A
10,7MHZ MS3A
AHK7-850978
AHK7-850981
7101
7102
7111
7180
7181
9351 740 80557
4822 130 42131
5322 130 42755
4822 130 60373
5322 130 42755
TEA5757H/V1
BF550
BC847C
BC856B
BC847C
5114
5119
5123
5130
5131
9965 000 16905
9965 000 16906
9965 000 16907
9965 000 16908
9965 000 16908
AHK7-850981
KHI7-855142
OHK7-850977
FT10-878842
FT10-878842
7182
7183
IC60
IC60
IC60
5322 130 42755
5322 130 42755
9965 000 16920
9965 000 16921
9322 143 49668
BC847C
BC847C
PT6955
P87C54X2BBD
M24C01-RDW6
L704
X1
Y1
9965 000 16910
9965 000 16911
9965 000 16912
9965 000 16913
220µH (4X5)
CRA8,467M3
CRA12,0M3
75KHZ/12,5pF
IC70
IC70
IC90
Q601
Q603
9965 000 16922
9965 000 16923
5322 209 83002
4822 130 61311
9965 000 16924
SAA7824HL
MM1469AH
TDA2822M
2SA1162Y
2SC2712-GR
12 - 2
ELECTRICAL PARTSLIST
- IC & TRANSISTORS Q604
Q701
Q704
Q705
Q801
4822 130 42615
9965 000 16927
9965 000 16928
9965 000 16926
9965 000 16927
BC817-40
KTC-9014C
KTC-8050C
2SB764
KTC-9014C
Q802
Q803
Q804
Q805
Q806
9965 000 16927
9965 000 04928
9965 000 04928
9965 000 04928
9965 000 04928
KTC-9014C
ON4986
ON4986
ON4986
ON4986
Q807
Q808
Q809
Q810
Q811
9965 000 16927
9965 000 16927
9965 000 16927
9965 000 16927
9965 000 16928
KTC-9014C
KTC-9014C
KTC-9014C
KTC-9014C
KTC-8050C
Q812
Q813
Q814
Q815
Q818
9965 000 16925
9965 000 16927
9965 000 16929
9965 000 16927
9965 000 16926
KTC-8550D
KTC-9014C
KTC-9015C
KTC-9014C
2SB764
Q819
Q820
Q821
Q841
9965 000 16927
4822 130 40981
4822 130 40981
9965 000 16928
KTC-9014C
BC337-25
BC337-25
KTC-8050C
Note: Only these parts mentioned in the list are
normal service parts.