Physical Description Functional Description Console Configuration

Hardened Managed Ethernet Switch
This quick start guide describes how to install and use the hardened Managed Gigabit Ethernet Switch.
Functional Description
This is the switch of choice for harsh environments constrained by space.
•
Meets NEMA TS1/TS2 Environmental requirements such as temperature, shock, and vibration for
traffic control equipment.
Physical Description
•
Meets EN61000-6-2 EMC Generic Standard Immunity for industrial environment.
The Port Status LEDs and Power Inputs
•
Manageable via SNMP, Web-based, Telnet, and RS-232 console port.
•
Support 802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation: 10/100/1000Mbps, full/half-duplex;
Auto MDI/MDIX.
•
100BaseFX: Multi mode SC or ST type; Single mode SC or ST type; WDM Single mode SC type.
•
1000BaseSX/LX: Multi mode or Single mode SC type; WDM Single mode SC type.
•
Support 8192 MAC addresses. Provides 256K Bytes memory buffer.
•
Power Supply: Redundant DC Terminal Block power inputs or 12VDC DC JACK with 100-240VAC
external power supply. "For Use with Model UP0351E-12P as power jack supply source by
Universal Micro Electronics Co., Ltd.".
•
Field Wiring Terminal: Use Copper Conductors Only, 60/75℃, 14-24 AWG torque value 4.5 lb-in.
•
Operating voltage and Max. current consumption: 0.7A @ 12VDC, 0.35A @ 24VDC. Power
consumption: 8.4W Max.
•
LED
State
Surrounding Air Temperature @ 70℃ (158℉).
10/100Base-TX, 100Base-FX
Steady
Link/ACT
Flashing
Steady
A valid network connection established.
ACT stands for ACTIVITY.
Link/ACT
Flashing
For use in Pollution Degree 2 Environment.
•
Supports Din-Rail, Panel, or Rack Mounting installation.
Communication speed is 100Mbps.
Power Input Assignment
Power3
Communication speed is 10Mbps.
Power1
10/100/1000Base-TX, 1000Base-SX/LX
Steady
•
Transmitting or receiving data.
10/100
Off
-40℃ to 75℃ (-40℉ to 167℉) operating temperature range. Tested for functional operation @
-40℃ to 85℃ (-40℉ to 185℉). UL508 Industrial Control Equipment certified Maximum
Indication
A valid network connection established.
12VDC
+
Console Configuration
DC Jack
•
12-32VDC
-
Power
Ground
+
12-32VDC
Power2
the terminal or computer running the terminal emulation application. Direct access to the
Terminal
Block
administration console is achieved by directly connecting a terminal or a PC equipped with a
terminal-emulation program (such as HyperTerminal) to the switch console port.
Transmitting or receiving data.
ACT stands for ACTIVITY.
Connect to the switch console:
Connect the DB9 straight cable to the RS-232 serial port of the device and the RS-232 serial port of
•
Earth Ground
Configuration settings of the terminal-emulation program:
Baud rate: 115,200bps
Steady
Communication speed is 1000Mbps.
Data bits: 8
Off
Communication speed is 10/100Mbps.
Parity: none
Steady
A valid network connection established.
Off
No valid network connection established.
1000
Stop bit: 1
Flow control: none.
SFP Link
•
•
Press the “Enter” key. The Command Line Interface (CLI) screen should appear as below:
Logon to Exec Mode (View Mode):
DC Terminal Block Power Inputs: There are two pairs of power inputs can be used to power up this switch.
At the “switch_a login:” prompt just type in “root” and press <Enter> to logon to Exec Mode (or View
Redundant power supplies function is supported.
Mode). And the “switch_a>” prompt will show on the screen.
1
V3
Hardened Managed Ethernet Switch
Web Configuration
•
Login the switch:
Specify the default IP address (192.168.1.10) of the switch in the web browser. A login window will be
shown as below:
•
Logon to Privileged Exec Mode (Enable Mode):
At the “switch_a>” prompt just type in “enable” and press <Enter> to logon to Privileged Exec Mode
(or Enable Mode). And the “switch_a#” prompt will show on the screen.
•
Logon to Configure Mode (Configure Terminal Mode):
At the “switch_a#” prompt just type in “configure terminal” and press <Enter> to logon to Configure
Mode (or Configure Terminal Mode). And the “switch_a(config)#” prompt will show on the screen.
•
Enter the factory default login ID: root.
Enter the factory default password (no password).
Then click on the “Login” button to log on to the switch.
2
V3
Download PDF

advertising