Thermometric Bi-spectrum Network Positioning System

Thermometric Bi-spectrum Network
Positioning System
User Manual
UD02221B
User Manual of Thermometric Bi-spectrum Network Positioning System
1
Thank you for purchasing our product. If there are any questions, or requests, please
do not hesitate to contact the dealer.
This manual applies to Thermometric Bi-spectrum Network Positioning System.
This manual may contain several technical or printing errors, and the content is
subject to change without notice. The updates will be added to the new version of
this manual. We will readily improve or update the products or procedures described
in the manual.
Different models may differ in functions, please refer to the actual GUI of each
model.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability
of the security or signaling aspects of this product. UL has only tested for fire, shock
or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the security or signaling
aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF
ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
0503061060818
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the
limits for Class A device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the Low Voltage
Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
3
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly
to avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are
neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are
neglected.
Warnings Follow these safeguards to Cautions Follow these precautions to
prevent serious injury or
prevent potential injury or
death.
material damage.
Warnings:
Please adopt the power adapter which can meet the safety extra low voltage
(SELV) standard. The power consumption cannot be less than the required value.
Do not connect several devices to one power adapter as an adapter overload may
cause over-heating and can be a fire hazard.
When the product is installed on a wall or ceiling, the device should be firmly
fixed.
To reduce the risk of fire or electrical shock, do not expose the indoor used
product to rain or moisture.
This installation should be made by a qualified service person and should
conform to all the local codes.
Please install blackouts equipment into the power supply circuit for convenient
supply interruption.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the product yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
4
Cautions:
Make sure the power supply voltage is correct before using the product.
Do not drop the product or subject it to physical shock. Do not install the product
on vibratory surface or places.
Do not expose it to high electromagnetic radiating environment.
Do not aim the lens at the strong light such as sun or incandescent lamp. The
strong light can cause fatal damage to the product.
The sensor may be burned out by a laser beam, so when any laser equipment is
being used, make sure that the surface of the sensor not be exposed to the laser
beam.
For working temperature, please refer to the specification manual for details.
To avoid heat accumulation, good ventilation is required for a proper operating
environment.
While shipping, the product should be packed in its original packing.
Please use the provided glove when open up the product cover. Do not touch the
product cover with fingers directly, because the acidic sweat of the fingers may
erode the surface coating of the product cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the
product cover. Do not use alkaline detergents.
Improper use or replacement of the battery may result in hazard of explosion.
Please use the manufacturer recommended battery type.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
5
Table of Contents
CHAPTER 1
OVERVIEW ................................................................................................................. 8
1.1
OVERVIEW ......................................................................................................................................... 8
1.2
SYSTEM REQUIREMENT ........................................................................................................................ 8
1.3
FUNCTIONS ........................................................................................................................................ 9
CHAPTER 2
2.1
NETWORK CONNECTION .......................................................................................... 12
SETTING THE NETWORK POSITIONING SYSTEM OVER THE LAN ................................................................12
2.1.1
Wiring over the LAN ................................................................................................................12
2.1.2
Activating the Positioning system ..........................................................................................13
2.2
SETTING THE NETWORK POSITIONING SYSTEM OVER THE WAN...............................................................18
2.2.1
Static IP Connection .................................................................................................................18
2.2.2
Dynamic IP Connection ...........................................................................................................19
CHAPTER 3
ACCESS TO THE NETWORK POSITIONING SYSTEM .................................................... 22
3.1
ACCESSING BY WEB BROWSERS ..........................................................................................................22
3.2
ACCESSING BY CLIENT SOFTWARE ........................................................................................................24
CHAPTER 4
LIVE VIEW ................................................................................................................ 26
4.1
POWER-UP ACTION ...........................................................................................................................26
4.2
LIVE VIEW PAGE................................................................................................................................26
4.3
STARTING LIVE VIEW .........................................................................................................................27
4.4
RECORDING AND CAPTURING PICTURES MANUALLY ...............................................................................29
4.5
OPERATING PTZ CONTROL .................................................................................................................30
4.5.1
PTZ Control Panel ....................................................................................................................30
4.5.2
Setting / Calling a Preset .........................................................................................................31
4.5.3
Setting / Calling a Patrol .........................................................................................................33
4.5.4
4.6
Setting / Calling a Pattern .......................................................................................................35
CONFIGURING LIVE VIEW PARAMETERS ................................................................................................36
CHAPTER 5
PTZ CONFIGURATION ............................................................................................... 37
5.1
CONFIGURING BASIC PTZ PARAMETERS ...............................................................................................37
5.2
CONFIGURING PTZ LIMITS .................................................................................................................38
5.3
CONFIGURING INITIAL POSITION..........................................................................................................39
5.4
CONFIGURING PARK ACTIONS .............................................................................................................40
5.5
CONFIGURING PRIVACY MASK ............................................................................................................41
5.6
CONFIGURING SCHEDULED TASKS ........................................................................................................42
5.7
CLEARING PTZ CONFIGURATIONS ........................................................................................................44
5.8
CONFIGURING PTZ CONTROL PRIORITY ................................................................................................44
CHAPTER 6
SYSTEM CONFIGURATION......................................................................................... 45
6.1
CONFIGURING LOCAL PARAMETERS ..................................................................................................... 45
6.2
CONFIGURING TIME SETTINGS ............................................................................................................47
6.3
CONFIGURING NETWORK SETTINGS ..................................................................................................... 49
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
6
6.3.1
Configuring TCP/IP Settings ....................................................................................................49
6.3.2
Configuring Port Settings ........................................................................................................51
6.3.3
Configuring PPPoE Settings.....................................................................................................52
6.3.4
Configuring DDNS Settings .....................................................................................................52
6.3.5
Configuring SNMP Settings .....................................................................................................55
6.3.6
Configuring 802.1X Settings ...................................................................................................56
6.3.7
Configuring QoS Settings ........................................................................................................58
6.3.8
Configuring FTP Settings .........................................................................................................58
6.3.9
Configuring UPnP™ Settings ...................................................................................................60
6.3.10
Configuring NAT (Network Address Translation) Settings ................................................61
6.3.11
Configuring Email Settings .................................................................................................61
6.3.12
Configuring HTTPS Settings ................................................................................................63
6.4
CONFIGURING VIDEO AND AUDIO SETTINGS .........................................................................................65
6.4.1
Configuring Video Settings......................................................................................................65
6.4.2
Configuring Audio Settings .....................................................................................................66
6.4.3
6.5
Configuring ROI Settings .........................................................................................................67
CONFIGURING IMAGE SETTINGS ..........................................................................................................68
6.5.1
Configuring Display Settings ...................................................................................................68
6.5.2
Configuring OSD Settings ........................................................................................................77
6.5.3
Configuring Text Overlay Settings ..........................................................................................79
6.5.4
6.6
Configuring DPC Settings ........................................................................................................79
CONFIGURING AND HANDLING ALARMS ...............................................................................................80
6.6.1
Configuring Motion Detection ................................................................................................80
6.6.2
Configuring Video Tampering Alarm ......................................................................................85
6.6.3
Configuring Alarm Input .........................................................................................................86
6.6.4
Configuring Alarm Output ......................................................................................................87
6.6.5
Handling Exception ..................................................................................................................88
6.6.6
Detecting Audio Exception ......................................................................................................89
6.6.7
Detecting Dynamic Fire Source ...............................................................................................90
6.6.8
6.7
Detecting Ship ..........................................................................................................................91
TEMPERATURE MEASUREMENT ...........................................................................................................91
6.7.1
Temperature Measurement Configuration ............................................................................92
6.7.2
Temperature Measurement and Alarm .................................................................................93
CHAPTER 7
VCA CONFIGURATION .............................................................................................. 96
7.1
VCA RESOURCE CONFIGURATION ........................................................................................................96
7.2
CONFIGURING VCA INFORMATION ......................................................................................................96
7.3
ADVANCED CONFIGURATION ...............................................................................................................97
7.4
BEHAVIOR ANALYSIS ..........................................................................................................................99
7.5
CONFIGURE THE VCA INFO: FOR DETAILS, SEE 7.2 VCA RESOURCE CONFIGURATION .................................99
7.6
RULE CONFIGURATION DEMONSTRATION ...........................................................................................103
7.6.1
Line Crossing ..........................................................................................................................103
7.6.2
Intrusion .................................................................................................................................104
7.6.3
Region Entrance .....................................................................................................................105
7.6.4
Region Exiting ........................................................................................................................106
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
CHAPTER 8
7
RECORD SETTINGS.................................................................................................. 108
8.1
CONFIGURING NAS SETTINGS ..........................................................................................................108
8.2
INITIALIZING AND CONFIGURING STORAGE ..........................................................................................109
8.3
CONFIGURING RECORDING SCHEDULE................................................................................................110
8.4
CONFIGURING SNAPSHOT SETTINGS ..................................................................................................113
CHAPTER 9
PLAYBACK............................................................................................................... 116
CHAPTER 10
LOG SEARCHING ..................................................................................................... 120
CHAPTER 11
OTHERS .................................................................................................................. 121
11.1
MANAGING USER ACCOUNTS ...........................................................................................................121
11.1.1
Deleting a User ..................................................................................................................123
11.2
CONFIGURING RTSP AUTHENTICATION ..............................................................................................123
11.3
CONFIGURING ANONYMOUS VISIT ....................................................................................................124
11.4
CONFIGURING IP ADDRESS FILTER .....................................................................................................124
11.5
CONFIGURING SECURITY SERVICE SETTINGS ........................................................................................125
11.6
VIEWING DEVICE INFORMATION ........................................................................................................125
11.7
MAINTENANCE ...............................................................................................................................126
11.7.1
Rebooting the Positioning system ....................................................................................126
11.7.2
Restoring Default Settings ................................................................................................126
11.7.3
Importing/Exporting Configuration File ..........................................................................127
11.7.4
Upgrading the System.......................................................................................................127
11.8
CONFIGURING RS-485 ....................................................................................................................128
11.9
CONFIGURING SUPPLEMENT LIGHT ....................................................................................................129
APPENDIX ...................................................................................................................................... 130
APPENDIX 1 SADP SOFTWARE INTRODUCTION ................................................................................................130
APPENDIX 2 PORT MAPPING .........................................................................................................................132
APPENDIX 3 RS485 BUS CONNECTION ...........................................................................................................134
APPENDIX 4 24VAC WIRE GAUGE & TRANSMISSION DISTANCE.........................................................................137
APPENDIX 5 TABLE OF WIRE GAUGE STANDARDS..............................................................................................138
APPENDIX 6 ALARM IN/OUT CONNECTIONS ....................................................................................................139
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
8
Chapter 1 Overview
1.1 Overview
Thermometric bi-spectrum network positioning system (named as positioning system
in the chapters below) integrates the function of the decoder, thermal camera, and
the high-definition zoom camera. It performs temperature measurement, dynamic
fire source detection and other smart detections in the remote surveillance of the
power system, metallurgy system, and petrochemical engineering, and so on.
You can get a high-quality live view via web browser or client software.
The figure below shows the overview of the positioning system.
Figure 1-1 Overview of Thermometric Positioning System
1.2 System Requirement
System requirement of web browser accessing is as follows:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /
Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above
version, Mozilla Firefox 5 and above version and Google Chrome8 and above
versions.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
9
1.3 Functions
The functions vary depending on the models of positioning system.
Bi-spectrum
The positioning system has two lens, an optical one and a thermal one, and two
images are respectively provided by each lens.
PTZ Limits
The positioning system can be programmed to move within the PTZ stops (left/right,
up/down).
Scan Modes
The positioning system provides 5 scan modes: auto scan, tilt scan, frame scan,
random scan and panorama scan.
Presets
A preset is a predefined image position. When the preset is called, the positioning
system will automatically move to the defined position. The presets can be added,
modified, deleted and called.
Label Display
The on-screen label of the preset title, azimuth/elevation, zoom, time and
positioning system name can be displayed on the monitor. The displays of time and
positioning system name can be programmed.
Auto Flips
In manual tracking mode, when a target object goes directly beneath the positioning
system, the video will automatically flips 180 degrees in horizontal direction to
maintain continuity of tracking. This function can also be realized by auto mirror
image depending on different camera models.
Privacy Mask
This function allows you to block or mask certain area of a scene, for preventing the
personal privacy from recording or live viewing. A masked area will move with pan
and tilt functions and automatically adjust in size as the lens zooms telephoto and
wide.
3D Positioning
In the client software, use the left key of mouse to click on the desired position in the
video image and drag a rectangle area in the lower right direction, then the
positioning system system will move the position to the center and allow the
rectangle area to zoom in. Use the left key of mouse to drag a rectangle area in the
upper left direction to move the position to the center and allow the rectangle area
to zoom out.
Proportional Pan/Tilt
Proportional pan/tilt automatically reduces or increases the pan and tilt speeds
according to the amount of zoom. At telephoto zoom settings, the pan and tilt
speeds will be slower than at wide zoom settings. This keeps the image from moving
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
10
too fast on the live view image when there is a large amount of zoom.
Auto Focus
The auto focus enables the camera to focus automatically to maintain clear video
images.
Day/Night Auto Switch
The positioning systems deliver color images during the day. And as light diminishes
at night, the positioning systems switch to night mode and deliver black and white
images with high quality.
Slow Shutter
In slow shutter mode, the shutter speed will automatically slow down in low
illumination conditions to maintain clear video images by extending the exposure
time. The feature can be enabled or disabled.
Backlight Compensation (BLC)
If you focus on an object against strong backlight, the object will be too dark to be
seen clearly. The BLC (Backlight Compensation) function can compensate light to the
object in the front to make it clear, but this causes the over-exposure of the
background where the light is strong.
Wide Dynamic Range (WDR)
The wide dynamic range (WDR) function helps the camera provide clear images even
under back light circumstances. When there are both very bright and very dark areas
simultaneously in the field of view, WDR balances the brightness level of the whole
image and provide clear images with details.
This feature varies depending on positioning system models.
White Balance (WB)
White balance can remove the unrealistic color casts. White balance is the white
rendition function of the camera to adjust the color temperature according to the
environment automatically.
Patrol
A patrol is a memorized series of pre-defined preset function. The scanning speed
between two presets and the dwell time at the preset are programmable.
Pattern
A pattern is a memorized series of pan, tilt, zoom, and preset functions. By default
the focus and iris are in auto status during the pattern is being memorized.
Power Off Memory
The positioning system supports the power off memory capability with the
predefined resume time. It allows the positioning system to resume its previous
position after power is restored.
Timing Task
A time task is a preconfigured action that can be performed automatically at a
specific date and time. The programmable actions include: auto scan, random scan,
patrol 1-8, pattern 1-4, preset 1-8,frame scan, panorama scan, tilt scan, day, night,
reboot, PT adjust, Aux Output, etc.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
11
Park Action
This feature allows the positioning system to start a predefined action automatically
after a period of inactivity.
User Management
The positioning system allows you to edit users with different levels of permission, in
the admin login status. Multiple users are allowed to access and control the same
network positioning system via network simultaneously.
3D Digital Noise Reduction
Comparing with the general 2D digital noise reduction, the 3D digital noise reduction
function processes the noise between two frames besides processing the noise in
one frame. The noise will be much less and the video will be clearer.
Dual-VCA
Combine the detected VCA information into the video stream, which can be used for
the second-time analysis on the back-end device.
VCA Detection
The positioning system allows you to do intelligent analysis and multiple rules can be
configured for different requirements.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning System
12
Chapter 2 Network Connection
Before you start:
If you want to set the network positioning system via a LAN (Local Area Network),
please refer to Section 2.1 Setting the Network Positioning system over the
LAN.
If you want to set the network positioning system via a WAN (Wide Area
Network), please refer to Section 2.2 Setting the Network Positioning system
over the WAN.
2.1 Setting the Network Positioning system over the
LAN
Purpose:
To view and configure the positioning system via a LAN, you need to connect the
network positioning system in the same subnet with your computer, and install the
SADP or client software to search and change the IP of the network positioning
system.
For the detailed introduction of SADP, please refer to Appendix 1.
2.1.1 Wiring over the LAN
The following figures show the two ways of cable connection of a network
positioning system and a computer:
Purpose:
To test the network positioning system, you can directly connect the network
positioning system to the computer with a network cable as shown in Figure 2-1.
Refer to the Figure 2-2 to set the network positioning system over the LAN via a
switch or a router.
Network Cable
PT Camera
Figure 2-1 Connecting Directly
© Hikvision
13
User Manual of Thermometric Bi-spectrum Network Positioning system
Network Cable
PT Camera
Network Cable
Switch or Router
PC
Figure 2-2 Connecting via a Switch or a Router
2.1.2 Activating the Positioning system
Purpose:
You are required to activate the positioning system first before you can use the
positioning system.
Activation via Web Browser, Activation via SADP, and Activation via client software
are supported. In the following sections, activation via web browser and SADP will be
taken as examples. You may refer to the user manual of the positioning system for
the details of activation via client software.
Activation via Web Browser
Steps:
1. Power on the positioning system, and connect the positioning system to the
network.
2. Input the IP address into the address bar of the web browser, and click Enter to
enter the activation interface.
The default IP address of the positioning system is 192.168.1.64.
Figure 2-3 Activation Interface(Web)
3.
Create a password and input the password into the password field.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
4.
5.
14
STRONG PASSWORD RECOMMENDED– We highly recommend you
create a strong password of your own choosing (using a minimum of 8
characters, including at least three of the following categories: upper
case letters, lower case letters, numbers, and special characters) in
order to increase the security of your product. And we recommend you
reset your password regularly, especially in the high security system,
resetting the password monthly or weekly can better protect your
product.
Confirm the password.
Click OK to activate the positioning system and enter the live view interface.
Activation via SADP Software
SADP software is used for detecting the online device, activating the device, and
resetting the password.
Get the SADP software from the supplied disk or the official website, and install the
SADP according to the prompts. Follow the steps to activate the positioning system.
Steps:
1. Run the SADP software to search the online devices.
2. Check the device status from the device list, and select an inactive device.
Figure 2-4 SADP Interface
3.
Create a password and input the password in the password field, and confirm
the password.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
4.
5.
15
STRONG PASSWORD RECOMMENDED– We highly recommend you
create a strong password of your own choosing ((using a minimum of 8
characters, including at least three of the following categories: upper
case letters, lower case letters, numbers, and special characters) in
order to increase the security of your product. And we recommend you
reset your password regularly, especially in the high security system,
resetting the password monthly or weekly can better protect your
product.
Click OK to save the password.
You can check whether the activation is completed on the popup window. If
activation failed, please make sure that the password meets the requirement
and then try again.
Change the device IP address to the same subnet with your computer by either
modifying the IP address manually or checking the checkbox of Enable DHCP.
Figure 2-5 Modify the IP Address
6.
Input the password and click the Save button to activate your IP address
modification.
Activation via Client Software
The client software is versatile video management software for multiple kinds of
devices.
Get the client software from the supplied disk or the official website, and install the
software according to the prompts. Follow the steps to activate the camera.
Steps:
1. Run the client software and the control panel of the software pops up, as shown
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
16
in the figure below.
Figure 2-6 Control Panel
2. Click the Device Management icon to enter the Device Management interface,
as shown in the figure below.
Figure 2-7 Device Management Interface
3. Check the device status from the device list, and select an inactive device.
4. Click the Activate button to pop up the Activation interface.
5. Create a password and input the password in the password field, and confirm
the password.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
17
6. STRONG PASSWORD RECOMMENDED– We highly recommend you
create a strong password of your own choosing (using a minimum of 8
characters, including at least three of the following categories: upper
case letters, lower case letters, numbers, and special characters) in order
to increase the security of your product. And we recommend you reset
your password regularly, especially in the high security system, resetting
the password monthly or weekly can better protect your product.
Figure 2-8 Activation Interface
7. Click OK button to start activation.
8. Click the Modify Netinfo button to pop up the Network Parameter Modification
interface, as shown in the figure below.
Figure 2-9 Modifying the Network Parameters
9. Change the device IP address to the same subnet with your computer by either
modifying the IP address manually or checking the checkbox of Enable DHCP.
© Hikvision
18
User Manual of Thermometric Bi-spectrum Network Positioning system
10. Input the password to activate your IP address modification.
2.2 Setting the Network Positioning system over the
WAN
Purpose:
This section explains how to connect the network positioning system to the WAN
with a static IP or a dynamic IP.
2.2.1 Static IP Connection
Before you start:
Please apply a static IP from an ISP (Internet Service Provider). With the static IP
address, you can connect the network positioning system via a router or connect it to
the WAN directly.
Connecting the network positioning system via a router
Steps:
1. Connect the network positioning system to the router.
2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2
for detailed IP address configuration of the positioning system.
3. Save the static IP in the router.
4. Set port mapping, E.g., 80, 8000 and 554 ports. The steps for port mapping vary
depending on different routers. Please call the router manufacturer for assistance
with port mapping.
Refer to Appendix 2 for detailed information about port mapping.
5. Visit the network positioning system through a web browser or the client
software over the internet.
Network
Cable
Positioning
System
Network
Cable
Internet
Network
Cable
Router with Static IP
PC
Figure 2-10 Accessing the Positioning system through Router with Static IP
Connecting the network positioning system with static IP directly
© Hikvision
19
User Manual of Thermometric Bi-spectrum Network Positioning system
You can also save the static IP in the positioning system and directly connect it to the
internet without using a router. Refer to Section 2.2.2 Dynamic IP Connection for
detailed IP address configuration of the positioning system.
Network
Cable
Internet
Network
Cable
Positioning
System
PC
Figure 2-11 Accessing the Positioning system with Static IP Directly
2.2.2 Dynamic IP Connection
Before you start:
Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect
the network positioning system to a modem or a router.
Connecting the network positioning system via a router
Steps:
1. Connect the network positioning system to the router.
2. In the positioning system, assign a LAN IP address, the subnet mask and the
gateway. Refer to Section 2.1.2 for detailed LAN configuration.
3. In the router, set the PPPoE user name, password and confirm the password.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (Using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers, and special characters.) in
order to increase the security of your product.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
4. Set port mapping. E.g. 80, 8000 and 554 ports. The steps for port mapping vary
depending on different routers. Please call the router manufacturer for assistance
with port mapping.
Refer to Appendix 2 for detailed information about port mapping.
5. Apply a domain name from a domain name provider.
6. Configure the DDNS settings in the setting interface of the router.
7. Visit the positioning system via the applied domain name.
© Hikvision
20
User Manual of Thermometric Bi-spectrum Network Positioning system
Connecting the network positioning system via a modem
Purpose:
This positioning system supports the PPPoE auto dial-up function. The positioning
system gets a public IP address by ADSL dial-up after the positioning system is
connected to a modem. You need to configure the PPPoE parameters of the network
positioning system. Refer to Section 6.3.3 Configuring PPPoE Settings for detailed
configuration.
Network
Cable
Network
Cable
Internet
Network
Cable
Modem
Positioning
System
PC
Figure 2-12 Accessing the Positioning system with Dynamic IP
The obtained IP address is dynamically assigned via PPPoE, so the IP address
always changes after rebooting the positioning system. To solve the
inconvenience of the dynamic IP, you need to get a domain name from the DDNS
provider (E.g. DynDns.com). Please follow below steps for normal domain name
resolution and private domain name resolution to solve the problem.
Normal Domain Name Resolution
Domain Name
Resolution Server
Network
Cable
Positioning
System
Network
Cable
Internet
Network
Cable
Router with Static IP
(Port Mapping)
Figure 2-13 Normal Domain Name Resolution
Steps:
© Hikvision
PC
21
User Manual of Thermometric Bi-spectrum Network Positioning system
1. Apply a domain name from a domain name provider.
2. Configure the DDNS settings in the DDNS Settings interface of the network
positioning system. Refer to Section 6.3.4 Configuring DDNS Settings for detailed
configuration.
3. Visit the positioning system via the applied domain name.
Private Domain Name Resolution
PC + IP Server + Staic IP
Network
Cable
Positioning
System
Network
Cable
Internet
Network
Cable
Router with Static IP
(Port Mapping)
PC
Figure 2-14 Private Domain Name Resolution
Steps:
1. Install and run the IP Server software in a computer with a static IP.
2. Access the network positioning system through the LAN with a web browser or
the client software.
3. Enable DDNS and select IP Server as the protocol type. Refer to Section 6.3.4
Configuring DDNS Settings for detailed configuration.
© Hikvision
22
User Manual of Thermometric Bi-spectrum Network Positioning System
Chapter 3 Access to the Network
Positioning system
3.1 Accessing by Web Browsers
Steps:
1. Open the web browser.
2. In the address field, input the IP address of the network positioning system, e.g.,
192.168.1.64 and press the Enter key to enter the login interface.
3. Activate the positioning system for the first time using, refer to the section 2.1.2
Activating the Positioning system.
4. Select English as the interface language on the top-right of login interface.
5. Input the user name and password and click
.
The admin user should configure the device accounts and user/operator
permissions properly. Delete the unnecessary accounts and user/operator
permissions.
The device IP address gets locked if the admin user performs 7 failed password
attempts (5 attempts for the user/operator).
Figure 3-1 Login Interface
6.
Install the plug-in before viewing the live video and operating the positioning
system. Please follow the installation prompts to install the plug-in.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
Figure 3-2 Download and Install Plug-in
Figure 3-3 Install Plug-in (1)
Figure 3-4 Install Plug-in (2)
© Hikvision
23
User Manual of Thermometric Bi-spectrum Network Positioning system
24
Figure 3-5 Install Plug-in (3)
You may have to close the web browser to install the plug-in. Please reopen the
web browser and log in again after installing the plug-in.
3.2 Accessing by Client Software
The product CD contains the client software. You can view the live video and manage
the positioning system with the client software.
Follow the installation prompts to install the client software and WinPcap. The
configuration interface and live view interface of client software are shown below.
Figure 3-6 iVMS-4200 Control Panel
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
25
Figure 3-7 iVMS-4200 Live View Interface
If you use third party VMS software, please contact technical support of our
branch for camera firmware.
For detailed information about client software of our company, please refer to
the user manual of the software. This manual mainly introduces accessing to the
network positioning system by web browser.
© Hikvision
26
User Manual of Thermometric Bi-spectrum Network Positioning system
Chapter 4 Live View
In this and the following chapters, operation of the positioning system by the web
browser R will be taken as an example.
4.1 Power-up Action
After the power is applied, the positioning system will perform self-test actions. It
begins with lens actions and then pan and tilt movement. After the power-up
self-test actions, the information as shown in Figure 4-1 will be displayed on screen
for 40 seconds.
The System Information displayed on the screen includes the positioning system
model, address, protocol, version and other information. The COMMUNICATION
refers to the baud rate, parity, data bit and stop bit of the positioning system. e.g.,
“2400, N, 8, 1” indicates the positioning system is configured with the baud rate of
2400, no parity, 8 data bits and 1 stop bit.
Model
Address
Communication
XX-XXXXXX-X
0
0000,0,0,0
Software Version
Vx.x.x
Camera Version
Vx.xx
Language
English
Figure 4-1 Power-up Information
4.2 Live View Page
Purpose:
The live video page allows you to view live video, capture images, realize PTZ control,
set/call presets and configure video parameters.
Log in the network positioning system to enter the live view page, or you can click
on the menu bar of the main page to enter the live view page.
© Hikvision
27
User Manual of Thermometric Bi-spectrum Network Positioning system
Descriptions of the live view page:
Menu Bar
Show or hide PTZ
control panel
Live View
Parameters
Camera List
PTZ Control
Live View Window
Toolbar
Preset/Patrol/Pattern
Figure 4-2 Live View Page
Menu Bar:
Click each tab to enter Live View, Playback, Log and Configuration page respectively.
Live View Window:
Display the live video.
Toolbar:
Operations on the live view page, e.g., live view, capture, record, audio on/off,
two-way audio, etc.
PTZ Control:
Panning, tilting, focusing and zooming actions of the positioning system. The lighter,
wiper, one-touch focus and lens initialization control.
Preset/patrol/pattern:
Set and call the preset/patrol/pattern for the positioning system.
Live View Parameters:
Configure the image size and stream type of the live video.
4.3 Starting Live View
In the live view window as shown in Figure 4-3, click
live view of the positioning system.
© Hikvision
on the toolbar to start the
28
User Manual of Thermometric Bi-spectrum Network Positioning system
Figure 4-3 Start Live View
Table 4-1 Descriptions of the Toolbar
Icon
Description
/
Start/Stop Live view
/
Manual recording off/on
/
Two-way audio off/on/
Icon
Description
Manually capture the
pictures
/ Mute / Audio on and
adjust volume
3D positioning
Manual tracking
Not all the positioning system models support the above functions. Please take
the browser interface of the actual product as standard.
Before enabling the two-way audio or recording with audio functions, please
set the Stream Type to Video & Audio referring to Section 6.4.1 Configuring
Video Settings.
Full-screen Mode:
You can double-click on the live video to switch the current live view into full-screen
or return to normal mode from the full-screen.
Multi-screen Mode:
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
29
You can select the window division mode in the dropdown list, there are single and
2*2 selectable. And you can click to select a window and then double-click a camera
to specify the camera order to view.
3D Positioning:
Steps:
1.
Click
2.
Operate the 3D positioning function:
on the toolbar of live view interface.
Left click a position of the live video. The corresponding position will be
moved to the center of the live video.
Hold down the left mouse button and drag the mouse to the lower right on
the live video. The corresponding position will be moved to the center of the
live video and zoomed in.
Hold down the left mouse button and drag the mouse to the upper left on
the live video. The corresponding position will be moved to the center of the
live video and zoomed out.
Manual Tracking:
Before you start:
Please enter the Smart Tracking settings interface and enable smart tracking first.
Configuration > Advanced Configuration> PTZ > Smart Tracking
Steps:
1.
Click
on the toolbar of live view interface.
2. Click a moving object in the live video.
The positioning system will track the object automatically.
Please refer to the following sections for more information:
Configuring remote recording in Section 8.3 Configuring Recording Schedule.
Setting the image quality of the live video in Section 6.1 Configuring Local
Parameters and Section 6.4.1 Configuring Video Settings.
Setting the OSD text on live video in Section 6.5.2 Configuring OSD Settings.
4.4 Recording and Capturing Pictures Manually
In the live view interface, click
on the toolbar to capture the live pictures and
the captured image will be saved as a JPEG file in your computer by default.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
You can click
30
to record the live video.
The local saving paths of the captured pictures and clips can be set in the
Configuration > Local Configuration interface and the image format can also be
edited in that interface.
To configure remote automatic recording, please refer to Section 8.3 Configuring
Recording Schedule.
4.5 Operating PTZ Control
Purpose:
In the live view interface, you can use the PTZ control buttons to control panning,
tilting and zooming.
4.5.1 PTZ Control Panel
On the live view page, click
to show the PTZ control panel or click
to
hide it.
Click the direction buttons to control the pan/tilt movements, while the pan angle
ranges from the 0° to 360° and the tilt angle range is from -15° to 90°.
Click the zoom/iris/focus buttons to realize lens control.
The range of tilt movement angle varies according to different models.
The lens control operations are supported by the optical channel only.
Figure 4-4 PTZ Control Panel
Table 4-2 Descriptions of PTZ Control Panel
Button
Description
Zoom in/out
Focus near/far
Iris +/Adjust speed of pan/tilt movements
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
31
4.5.2 Setting / Calling a Preset
Purpose:
A preset is a predefined image position. For the defined preset, you can click the
calling button to quickly view the desired image position.
Setting a Preset:
Steps:
1. In the PTZ control panel, select a preset number from the preset list.
Figure 4-5 Setting a Preset
2. Use the PTZ control buttons to move the lens to the desired position.
Pan the positioning system to the right or left.
Tilt the positioning system up or down.
Zoom in or out.
Refocus the lens.
3. Click
to finish the setting of the current preset.
4. You can click
to delete the preset.
You can configure up to 300 presets.
Calling a Preset:
In the PTZ control panel, select a defined preset from the list and click
preset.
© Hikvision
to call the
32
User Manual of Thermometric Bi-spectrum Network Positioning system
Figure 4-6 Calling a Preset
For convenient preset selection, refer to the following steps to navigate to the preset
you want.
Steps:
1. Select any preset from the list.
2. Click the preset number you need on the keyboard.
The following presets are predefined with special commands. You can only call
them but not configure them. For instance, preset 99 is the “Start auto scan”. If
you call the preset 99, the positioning system starts auto scan function.
Table 4-3 Special Presets
Special
Preset
33
34
35
36
37
38
39
40
41
42
43
44
45
92
Function
Auto flip
Back to initial position
Call patrol 1
Call patrol 2
Call patrol 3
Call patrol 4
IR cut filter in
IR cut filter out
Call pattern 1
Call pattern 2
Call pattern 3
Call pattern 4
Automatically Create Patrol
Start to set limit stops
© Hikvision
Special
Preset
93
94
95
96
97
98
99
100
101
102
103
104
105
Function
Set limit stops manually
Remote reboot
Call OSD menu
Stop a scan
Start random scan
Start frame scan
Start auto scan
Start tilt scan
Start panorama scan
Call patrol 5
Call patrol 6
Call patrol 7
Call patrol 8
User Manual of Thermometric Bi-spectrum Network Positioning system
33
Figure 4-7 Special Preset
You may need to use the OSD (On Screen Display) menu when controlling
the positioning system remotely. To display the OSD menu on the live view
screen, you can call the preset number 95.
4.5.3 Setting / Calling a Patrol
Purpose:
A patrol is a memorized series of preset function. It can be configured and called on
the patrol settings interface. There are up to 8 patrols for customizing. A patrol can
be configured with 32 presets.
Before you start:
Please make sure that the presets you want to add into a patrol have been defined.
Setting a Patrol:
Steps:
1. In the PTZ control panel, click
2. Select a patrol number from
3. Click
to enter the patrol settings interface.
.
to enter the adding interface of preset, as shown in Figure 4-8.
Figure 4-8 Adding Presets
© Hikvision
34
User Manual of Thermometric Bi-spectrum Network Positioning system
4. Configure the preset number, patrol time and patrol speed.
Name
Description
Patrol Time
It is the duration staying on one patrol point. The
positioning system moves to another patrol point after the
patrol time.
Patrol Speed
It is the speed of moving from one preset to another.
5. Click
to save a preset into the patrol.
6. Repeat the steps from 3 to 5 to add more presets.
to save all the patrol settings.
7. Click
Calling a Patrol:
In the PTZ control panel, select a defined patrol from
and click
call the patrol, as shown in Figure 4-9.
Figure 4-9 Calling a Patrol
Buttons on the Patrols interface:
Buttons
Description
Save a patrol
Call a patrol
Stop a patrol
Enter the adding interface of preset
Modify a preset
Delete a preset
Delete all the presets in the selected patrol
© Hikvision
to
User Manual of Thermometric Bi-spectrum Network Positioning system
35
4.5.4 Setting / Calling a Pattern
Purpose:
A pattern is a memorized series of pan, tilt, zoom, and preset functions. It can be
called on the pattern settings interface. There are up to 4 patterns for customizing.
Setting a Pattern:
Steps:
1. In the PTZ control panel, click
to enter the pattern settings interface.
2. Select a pattern number from the list as shown in Figure 4-10.
Figure 4-10 Patterns Settings Interface
3. Click
to enable recording the panning, tilting and zooming actions.
4. Use the PTZ control buttons to move the lens to the desired position after the
information of Program Pattern Remaining Memory (%) is displayed on the
screen.
• Pan the positioning system to the right or left.
• Tilt the positioning system up or down.
• Zoom in or out.
• Refocus the lens.
5. Click
to save all the pattern settings.
Buttons on the Patterns interface:
Buttons
Description
Start to record a pattern.
Stop recording a pattern.
Call the current pattern.
Stop the current pattern.
Delete the current pattern.
These 4 patterns can be operated separately and with no priority level.
© Hikvision
36
User Manual of Thermometric Bi-spectrum Network Positioning system
When configuring and calling the pattern, proportional pan is valid; the limit
stops and auto flip will be invalid; and the 3D positioning operation is not
supported.
4.6 Configuring Live View Parameters
Main stream/Sub-stream:
You can select
or
as the stream type of live viewing. The main
stream is with a relatively high resolution and needs much bandwidth. The
sub-stream is with a low resolution and needs less bandwidth. The default setting of
stream type is
.
Please refer to Section 6.4.1 Configuring Video Settings for more detailed
parameter settings of the main stream and sub-stream respectively.
Image Size:
You can scale up/down the live view image by clicking
size can be 4:3, 16:9, original or auto.
© Hikvision
,
,
,
. The image
User Manual of Thermometric Bi-spectrum Network Positioning System
37
Chapter 5 PTZ Configuration
5.1 Configuring Basic PTZ Parameters
Purpose:
You can configure the basic PTZ parameters, including proportional pan, preset
freezing, preset speed, etc.
1. Enter the Basic PTZ Parameter Configuration interface:
Configuration > Advanced Configuration > PTZ > Basic
Figure 5-1 Basic PTZ Configuration Interface
2. Configure the following settings:
Basic Parameters: Enable/disable proportional pan, set the preset speed,
keyboard control speed, auto scan speed, and zooming speed.
Proportional Pan: If you enable this function, the pan/tilt speeds change
according to the amount of zoom. When there is a large amount of zoom, the
pan/tilt speed will be slower for keeping the image from moving too fast on
the live view image.
Preset Speed: You can set the speed of a defined preset from 1 to 8.
Keyboard Control Speed: Define the speed of PTZ control by a keyboard as
Low, Normal or High.
Auto Scan Speed: The positioning system provides 5 scan modes: auto scan,
tilt scan, frame scan, random scan and panorama scan. The scan speed can be
set from level 1 to 40.
Zooming Speed: The zoom speed is adjustable from level 1 to 3.
PTZ OSD: Set the on-screen display duration of the PTZ status.
Zoom Status: Set the OSD duration of zooming status as 2 seconds, 5 seconds,
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
38
10 seconds, Always Close or Always Open.
PT Status: Set the azimuth angle display duration while panning and tilting as
2 seconds, 5 seconds, 10 seconds, Always Close or Always Open.
Preset Status: Set the preset name display duration while calling the preset as
2 seconds, 5 seconds, 10 seconds, Always Close or Always Open.
Power-off Memory: The positioning system can resume its previous PTZ status or
actions after it restarted from a power-off. You can set the time point of which
the positioning system resumes its PTZ status. You can set it to resume the status
of 30 seconds, 60 seconds, 300 seconds or 600 seconds before power-off.
3. Click
to save the settings.
5.2 Configuring PTZ Limits
Purpose:
The positioning system can be programmed to move within the configurable limits
(left/right, up/down).
Steps:
1. Enter the Limit Configuration interface:
Configuration > Advanced Configuration > PTZ > Limit
Figure 5-2 Configure the PTZ Limit
2. Click the checkbox of Enable Limit and choose the limit type as manual stops or
scan stops.
Manual Stops:
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
39
When manual limit stops are set, you can operate the PTZ control panel
manually only in the limited surveillance area.
Scan Stops:
When scan limit stops are set, the random scan, frame scan, auto scan, tilt scan,
panorama scan is performed only in the limited surveillance area.
Manual Stops of Limit Type is prior to Scan Stops. When you set these two
limit types at the same time, Manual Stops is valid and Scan Stops is invalid.
3. Click the PTZ control buttons to find the left/right/up/down limit stops; you can
also call the defined presets and set them as the limits of the positioning system.
4. Click Set to save the limits or click Clear to clear the limits.
5.3 Configuring Initial Position
Purpose:
The initial position is the origin of PTZ coordinates. It can be the factory default initial
position. You can also customize the initial position according to your own demand.
Customize an Initial Position:
Steps:
1. Enter the Initial Position Configuration interface:
Configuration > Advanced Configuration > PTZ > Initial Position
Figure 5-3 PTZ Configuration
2. Click the PTZ control buttons to find a position as the initial position of the
positioning system; you can also call a defined preset and set it as the initial
position of the positioning system.
3. Click Set to save the position.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
40
Call/delete an Initial Position:
You can click
to call the initial position. You can click
to delete the
initial position and restore the factory default initial position.
5.4 Configuring Park Actions
Purpose:
This feature allows the positioning system to start a predefined park action (scan,
preset, pattern and etc.) automatically after a period of inactivity (park time).
Scheduled Tasks function is prior to Park Action function. When these two
functions are set at the same time, only the Scheduled Tasks function takes
effect.
Steps:
1. Enter the Park Action Settings interface:
Configuration > Advanced Configuration> PTZ > Park Action
Figure 5-4 Set the Park Action
2. Check the checkbox of Enable Park Action.
3. Set the Park Time as the inactivity time of the positioning system before it starts
the park actions.
4. Choose Action Type the from the drop-down list.
Figure 5-5 Action Types
© Hikvision
41
User Manual of Thermometric Bi-spectrum Network Positioning system
5. Click
to save the settings.
5.5 Configuring Privacy Mask
Purpose:
Privacy mask enables you to cover certain areas on the live video to prevent certain
spots in the surveillance area from being live viewed and recorded.
The privacy mask function is supported by the optical lens only.
Steps:
1. Enter the Privacy Mask Settings interface:
Configuration > Advanced Configuration> PTZ > Privacy Mask
Figure 5-6 Draw the Privacy Mask
2.
3.
Click the PTZ control buttons to find the area you want to set the privacy mask.
Click
; click and drag the mouse in the live video window to draw the
area.
You can drag the corners of the red rectangle area to draw a polygon mask.
4.
Click
5.
set without saving them.
Click
to save the privacy mask, and it will be listed in the Privacy Mask
© Hikvision
to finish drawing or click
to clear all of the areas you
User Manual of Thermometric Bi-spectrum Network Positioning system
6.
42
List area; set the value of Active Zoom Ratio on your demand, and then the
mask will only appear when the zoom ratio is greater than the predefined value.
You can also define the color of the masks.
Figure 5-7 Define Mask Color
7.
You can select a mask and click
to delete it from the list.
8.
Check the checkbox of Enable Privacy Mask to enable this function.
You are allowed to draw up to 24 areas on the same image.
5.6 Configuring Scheduled Tasks
Purpose:
You can configure the network positioning system to perform a certain action
automatically in a user-defined time period.
Steps:
1. Enter the Scheduled Task Settings interface:
Configuration> Advanced Configuration> PTZ > Scheduled Tasks
Figure 5-8 Configure Scheduled Tasks
2. Check the checkbox of Enable Scheduled Task.
3. Set the Park Time. You can set the park time (a period of inactivity) before the
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
43
positioning system starts the scheduled tasks.
4. Set the schedule and task details.
(1) Click
to edit the task schedule.
Figure 5-9 Edit the Schedule and Task Type
(2) Choose the day you want to set the task schedule.
(3) Click All Day to set the schedule as all day; or click Customize and input the
Start Time and End Time for each task, and click Enter on your keyboard to
enter the time.
(4) Choose the task type from the drop-down list. You can choose scan, preset,
pattern and etc.
Figure 5-10 Task Types
(5) After you set the scheduled task, you can copy the task to other days
(Optional).
(6) Click
© Hikvision
to save the settings.
User Manual of Thermometric Bi-spectrum Network Positioning system
44
The time of each task cannot be overlapped. Up to 10 tasks can be
configured for each day.
5. Click
to save the settings.
5.7 Clearing PTZ Configurations
Purpose:
You can clear PTZ configurations in this interface, including all presets, patrols,
patterns, privacy masks, PTZ limits and scheduled tasks.
Steps:
1. Enter the Clearing Configuration interface:
Configuration > Advanced Configuration> PTZ > Clear Config
2. Check the checkbox of the items you want to clear.
3. Click
to clear the settings.
5.8 Configuring PTZ Control Priority
Steps:
1. Get to the configuration interface:
Configuration > Advanced Configuration> PTZ > Prioritize PTZ.
The positioning system can be controlled by network and RS-485 signals. You
can set the control priority of these two signals.
The operation of Operator is prior to that of User. When the Operator is
controlling the positioning system, the User cannot control it. When the
Operator finishes, the User can control the positioning system after the Delay
time. The Delay time can be set in Priority PTZ interface as shown follows.
Figure 5-11 PTZ Priority
2. Click
to activate the settings.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
45
Chapter 6 System Configuration
6.1 Configuring Local Parameters
The local configuration refers to the parameters of the live view and other
operations using the web browser.
Steps:
1. Enter the Local Configuration interface:
Configuration > Local Configuration
Figure 6-1 Local Configuration Interface
2. Configure the following settings:
Live View Parameters: Set the protocol type, stream type, image size and live
view performance.
Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable.
TCP: Ensures complete delivery of streaming data and better video quality,
yet the real-time transmission will be affected.
UDP: Provides real-time audio and video streams.
HTTP: Allows the same quality as of TCP without setting specific ports for
streaming under some network environments.
MULTICAST: It’s recommended to select the protocol type to
when using the Multicast function. For other information about Multicast,
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
refer to Section 6.3.1 Configuring TCP/IP Settings.
Live View Performance: Set the live view performance to Shortest Delay, or
Auto.
Please set Live View Performance as Best Fluency for the high frame rate
positioning system.
Auto Start Live View: You can enable the function if you want to view the live
view image directly when you log in the device.
Rules: You can enable or disable the rules of dynamic analysis for events here.
Image Format: The captured pictures can be saved as different format. JPEG
and BMP are available.
Fire Point: Select Fire Source Detection as VCA Resource Type. Check the
checkbox to enable the functions required. Display Fire Point Distance,
Display Highest Temperature, Locate Highest Temperature Point and Frame
Fire Point are selectable.
Display Temperature Info. on Stream: Select Temperature Measurement as
VCA Resource Type. Check the checkbox to display the temperature
information on the live view interface.
Display Temperature Info. on Capture: Select Temperature Measurement as
VCA Resource Type. Check the checkbox to display the temperature
information on the captures.
Record File Settings: Set the saving path of the video files.
Record File Size: Select the packed size of manually recorded and downloaded
video files. The size can be set to 256M, 512M or 1G.
Save record files to: Set the saving path for the manually recorded video files.
Save downloaded files to: Set the saving path for the downloaded video files
in
46
interface.
Picture and Clip Settings: Set the saving paths of the captured pictures and
clipped video files.
Save snapshots in live view to: Set the saving path of the manually captured
pictures in
interface.
Save snapshots when playback to: Set the saving path of the captured
pictures in
interface.
Save clips to: Set the saving path of the clipped video files in
interface.
You can click
© Hikvision
to change the directory for saving video files, clips
User Manual of Thermometric Bi-spectrum Network Positioning system
47
and pictures.
3. Click
to save the settings.
6.2 Configuring Time Settings
Purpose:
You can follow the instructions in this section to configure the time which can be
displayed on the video. There are Time Zone, Time Synchronization, Daylight Saving
Time (DST) functions for setting the time. Time Synchronization consists of auto
mode by Network Time Protocol (NTP) server and manual mode.
To enter the Time Settings interface:
Configuration > Basic Configuration > System > Time Settings
Or Configuration > Advanced Configuration > System > Time Settings
Figure 6-2 Time Settings
Configuring Time Synchronization by NTP Server
Steps:
(1) Check the radio button to enable the NTP function.
(2) Configure the following settings:
Server Address: IP address of NTP server.
NTP Port: Port of NTP server.
Interval: The time interval between the two synchronizing actions by NTP server.
It can be set from 1 to 10080 minutes.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
48
Figure 6-3 Time Sync by NTP Server
(3) You can click the
button to check whether the confguration is
succeeded.
If the positioning system is connected to a public network, you should use a
NTP server that has a time synchronization function, such as the server at
the National Time Center (IP Address: 210.72.145.44). If the positioning
system is set in a customized network, NTP software can be used to
establish a NTP server for time synchronization.
Configuring Time Synchronization Manually
Steps:
(1) Check the Manual Time Sync radio button.
(2) Click
to set the system time from the pop-up calendar.
(3) Click
to save the settings.
You can also check the Sync. with computer time checkbox to synchronize
the time of the positioning system with the time of your computer.
Figure 6-4 Time Sync Manually
Select the Time Zone
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
49
Purpose:
When the positioning system is taken to another time zone, you can use the Time
Zone function to adjust the time. The time will be adjusted according to the
original time and the time difference between the two time zones.
From the Time Zone drop-down menu as shown in Figure 6-5, select the Time
Zone in which the positioning system locates.
Figure 6-5 Time Zone Settings
Configuring Daylight Saving Time (summer time)
Purpose:
If there is the habit of adjusting clocks forward in your country in certain time
period of a year, you can turn this function on. The time will be adjusted
automatically when the Daylight Saving Time(DST) comes.
Steps:
(1) Enter the DST interface by Configuration > Advanced Configuration >
System > DST
(2) Check
to enable the DST function.
(3) Set the date of the DST period.
(4) Click
to save the settings.
Figure 6-6 DST Settings
6.3 Configuring Network Settings
6.3.1 Configuring TCP/IP Settings
Purpose:
TCP/IP settings must be properly configured before you operate the positioning
system over network. IPv4 and IPv6 are both supported.
Steps:
© Hikvision
50
User Manual of Thermometric Bi-spectrum Network Positioning system
1. Enter TCP/IP Settings interface:
Configuration > Basic Configuration > Network > TCP/IP
Or Configuration > Advanced Configuration > Network > TCP/IP
Figure 6-7 TCP/IP Settings
2. Configure the NIC settings, including the IPv4(IPv6) Address, IPv4(IPv6) Subnet
Mask and IPv4(IPv6) Default Gateway.
3. Click
to save the above settings.
to automatically obtain
If the DHCP server is available, you can check
an IP address and other network settings from that server.
If the IP address is set manually, you can click
to check whether the
IP address is already used to prevent the IP address confliction.
The valid value range of Maximum Transmission Unit (MTU) is 500 ~ 9676. The
default value is 1500.
The Multicast sends a stream to the multicast group address and allows multiple
clients to acquire the stream at the same time by requesting a copy from the
multicast group address.
Before utilizing this function, you have to enable the Multicast function of your
router and configure the gateway of the network positioning system.
If the DNS server settings are required for some applications (e.g., sending
email), you should properly configure the Preferred DNS Server and Alternate
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
51
DNS server.
Check the checkbox of Enable Multicast Discovery, and then the positioning
system can be detected by client software in the LAN.
Figure 6-8 DNS Server Settings
The router must support the route advertisement function if you select
Route Advertisement as the IPv6 mode.
6.3.2 Configuring Port Settings
Purpose:
If there is a router and you want to access the positioning system through Wide Area
Network (WAN), you need to forward the 3 ports for the positioning system.
Steps:
1. Enter the Port Settings interface:
Configuration > Basic Configuration > Network > Port
Or Configuration > Advanced Configuration > Network > Port
Figure 6-9 Port Settings
2. Set the HTTP port, RTSP port, HTTPS port and port of the positioning system.
HTTP Port: The default port number is 80.
RTSP Port: The default port number is 554.
HTTPS Port: The default port number is 443.
Server Port: The default port number is 8000.
3. Click
© Hikvision
to save the settings.
User Manual of Thermometric Bi-spectrum Network Positioning system
52
6.3.3 Configuring PPPoE Settings
Purpose:
If you have no router but only a modem, you can use Point-to-Point Protocol over
Ethernet (PPPoE) function.
Steps:
1. Enter the PPPoE Settings interface:
Configuration >Advanced Configuration > Network > PPPoE
Figure 6-10 PPPoE Settings
2. Check the Enable PPPoE checkbox to enable this feature.
3. Enter User Name, Password, and Confirm password for PPPoE access.
The User Name and Password should be assigned by your ISP.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers and special characters) in
order to increase the security of your product.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
4. Click
to save and exit the interface.
6.3.4 Configuring DDNS Settings
Purpose:
If your positioning system is set to use PPPoE as its default network connection, you
can use the Dynamic DNS (DDNS) for network access.
Before you start:
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
53
Registration on the DDNS server is required before configuring the DDNS settings of
the positioning system.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers and special characters) in
order to increase the security of your product.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
Steps:
1. Enter the DDNS Settings interface:
Configuration > Advanced Configuration > Network > DDNS
Figure 6-11 DDNS Settings
2. Check the Enable DDNS checkbox to enable this feature.
3. Select DDNS Type. Three DDNS types are selectable: IPServer, HiDDNS, NO-IP
and DynDNS.
DynDNS:
Steps:
(1) Enter Server Address of DynDNS (e.g. members.dyndns.org).
(2) In the Domain text field, enter the domain name obtained from the DynDNS
website.
(3) Enter the Port of DynDNS server.
(4) Enter the User Name and Password registered on the DynDNS website.
(5) Click
to save the settings.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
54
Figure 6-12 DynDNS Settings
IP Server:
Steps:
(1) Enter the Server Address of the IP Server.
(2) Click
to save the settings.
The Server Address should be entered with the static IP address of the
computer that runs the IP Server software. For the IP Server, you have to
apply a static IP, subnet mask, gateway and preferred DNS from the ISP.
Figure 6-13 IPServer Settings
HiDDNS:
Steps:
(1) Enter the Server Address: www.hik-online.com.
(2) Enter the Domain name of the camera. The domain is the same with the
device alias in the HiDDNS server.
to save the settings.
(3) Click
Figure 6-14 HiDDNS Settings
NO-IP:
Steps:
(1) Enter Server Address of NO-IP.
(2) In the Domain text field, enter the domain name obtained from the NO-IP
website.
(3) Enter the Port of NO-IP server.
(4) Enter the User Name and Password registered on the NO-IP website.
(5) Click
© Hikvision
to save the settings.
User Manual of Thermometric Bi-spectrum Network Positioning system
55
6.3.5 Configuring SNMP Settings
Purpose:
You can use SNMP to get positioning system status and parameters related
information.
Before you start:
Before setting the SNMP, please use the SNMP software and manage to receive the
positioning system information via SNMP port. By setting the Trap Address, the
positioning system can send the alarm event and exception messages to the
surveillance center.
The SNMP version you select should be the same as that of the SNMP software.
Steps:
1. Enter the SNMP Settings interface:
Configuration > Advanced Configuration > Network > SNMP
Figure 6-15 SNMP Settings
© Hikvision
56
User Manual of Thermometric Bi-spectrum Network Positioning system
2. Check the corresponding version checkbox (Enable SNMP v1, Enable SNMP v2c,
Enable SNMP v3) to enable the feature.
3. Configure the SNMP settings.
The configuration of the SNMP software should be the same as the settings
you configure here.
4. Click
to save and finish the settings.
6.3.6 Configuring 802.1X Settings
Purpose:
The positioning system supports IEEE 802.1X standard.
IEEE 802.1X is a port-based network access control. It enhances the security level of
the LAN. When devices connect to this network with IEEE 802.1X standard, the
authentication is needed. If the authentication fails, the devices don’t connect to the
network.
The protected LAN with 802.1X standard is shown as follows:
Authenticator
Network Switch
Speed Dome
Internet
Authentication
Server
PC
PC
RADIUS Server
Figure 6-16 Protected LAN
Before connecting the Network Camera to the protected LAN, please apply a
digital certificate from a Certificate Authority.
The network camera requests access to the protected LAN via the
authenticator (a switch).
The switch forwards the identity and password to the authentication server
(RADIUS server).
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
57
The switch forwards the certificate of authentication server to the network
camera.
If all the information is validated, the switch allows the network access to
the protected network.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers and special characters) in
order to increase the security of your product.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
Steps:
1. Connect the network camera to your PC directly with a network cable.
2. Enter the 802.1X Settings interface:
Configuration > Advanced Configuration > Network > 802.1X
Figure 6-17 802.1X Settings
3. Check the Enable IEEE 802.1X checkbox to enable it.
4. Configure the 802.1X settings, including user name and password.
The EAP-MD5 version must be identical with that of the router or the
switch.
5. Enter the user name and password (issued by the CA) to access the server.
6. Click
to finish the settings.
The camera reboots when you save the settings.
7. After the configuration, connect the camera to the protected network.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
58
6.3.7 Configuring QoS Settings
Purpose:
QoS (Quality of Service) can help solve the network delay and network congestion by
configuring the priority of data sending.
Steps:
1. Enter the QoS Settings interface:
Configuration >Advanced Configuration > Network > QoS
Figure 6-18 QoS Settings
2. Configure the QoS settings, including video / audio DSCP, event / alarm DSCP and
Management DSCP.
The valid DSCP value ranges from 0 to 63. The DSCP value is bigger, the priority is
higher.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers and special characters) in
order to increase the security of your product.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
3. Click
to save the settings.
Make sure that you enable the QoS function of your network device (such as a
router).
It will ask for a reboot for the settings to take effect.
6.3.8 Configuring FTP Settings
Purpose:
You can set a FTP server and configure the following parameters for uploading
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
59
captured pictures.
Steps:
1. Enter the FTP Settings interface:
Configuration >Advanced Configuration > Network > FTP
Figure 6-19 FTP Settings
2. Configure the FTP settings, including server address, port, user name, password,
directory and upload type.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers and special characters) in
order to increase the security of your product.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
The server address supports both the domain name and IP address formats.
Setting the directory in FTP server for saving files:
In the Directory Structure field, you can select the root directory, parent
directory and child directory.
Root directory: The files will be saved in the root of FTP server.
Parent directory: The files will be saved in a folder in FTP server. The
name of folder can be defined as shown in following Figure 6-20.
Figure 6-20 Parent Directory
Child directory: It is a sub-folder which can be created in the parent
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
60
directory. The files will be saved in a sub-folder in FTP server. The name of
folder can be defined as shown in following Figure 6-21.
Figure 6-21 Child Directory
Upload type: To enable uploading the captured picture to the FTP server.
3. Click
to save the settings.
If you want to upload the captured pictures to FTP server, you also have to
enable the continuous snapshot or event-triggered snapshot in Snapshot
interface. For detailed information, please refer to the Section 8.4
Configuring Snapshot Settings.
6.3.9 Configuring UPnP™ Settings
Purpose:
Universal Plug and Play (UPnP™) is a networking architecture that provides
compatibility among networking equipment, software and other hardware devices.
The UPnP protocol allows devices to connect seamlessly and to simplify the
implementation of networks in the house and corporate environments.
With the function enabled, you don’t need to configure the port mapping for each
port, and the camera is connected to the Wide Area Network via the router.
Steps:
1. Enter the UPnP™ settings interface.
Configuration >Advanced Configuration > Network > UPnP™
2. Check the checkbox to enable the UPnP™ function.
You can edit the Friendly Name of the positioning system. This name can be
detected by corresponding device, such as a router.
Figure 6-22 Configure UPnP Settings
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
61
6.3.10 Configuring NAT (Network Address Translation) Settings
Steps:
1. Set the port mapping mode:
To port mapping with the default port numbers:
Choose
To port mapping with the customized port numbers:
Choose
And you can customize the value of the port No. by yourself.
Figure 6-23 Configure the Port No.
2. Click
to save the settings.
6.3.11 Configuring Email Settings
Purpose:
The system can be configured to send an Email notification to all designated
receivers if an alarm event is detected, e.g., motion detection event, video loss,
tamper-proof, etc.
Before you start:
Please configure the DNS Server settings under Basic Configuration > Network >
TCP/IP or Advanced Configuration > Network > TCP/IP before using the Email
function.
Steps:
1. Enter the Email Settings interface:
Configuration > Advanced Configuration > Network > Email
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
62
Figure 6-24 Email Settings
2. Configure the following settings:
Sender: The name of the email sender.
Sender’s Address: The email address of the sender.
SMTP Server: The SMTP Server IP address or host name (e.g.,
smtp.263xmail.com).
SMTP Port: The SMTP port. The default TCP/IP port for SMTP is 25.
Enable SSL: Check the checkbox to enable SSL if it is required by the SMTP
server.
Attached Image: Check the checkbox of Attached Image if you want to send
emails with attached alarm images.
Interval: The interval refers to the time between two actions of sending attached
pictures.
Authentication (optional): If your email server requires authentication, check
this checkbox to use authentication to log in to this server and enter the login
user name and password.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers and special characters) in
order to increase the security of your product.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
63
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
Receiver: Select the receiver to which the email is sent. Up to 2 receivers can be
configured.
Receiver: The name of the user to be notified.
Receiver’s Address: The email address of user to be notified.
You can click
to check whether the setting is invalid after the
required parameters are configured.
3. Click
to save the settings.
6.3.12 Configuring HTTPS Settings
Purpose:
HTTPS provides authentication of the web site and associated web server that one is
communicating with, which protects against Man-in-the-middle attacks. Perform the
following steps to set the port number of https.
Example:
If you set the port number as 443 and the IP address is 192.168.1.64, you may access
the device by inputting https:// 192.168.1.64:443 via the web browser.
Steps:
1. Enter the HTTPS settings interface.
Configuration > Advanced Configuration > Network > HTTPS
2. Create the self-signed certificate or authorized certificate.
Figure 6-25 HTTPS Settings
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
64
OPTION 1: Create the self-signed certificate
1) Click the Create button to create the following dialog box.
Figure 6-26 Create Self-signed Certificate
2) Enter the country, host name/IP, validity and other information.
3) Click OK to save the settings.
OPTION 2: Create the authorized certificate
1) Click the Create button to create the certificate request, and fulfill the
required information.
2) Download the certificate request and submit it to the trusted certificate
authority for signature.
3) After receiving the signed valid certificate, import the certificate to the
device.
3. There will be the certificate information after you successfully create and install
the certificate.
Figure 6-27 Installed Certificate Property
You can click configure the HTTPS port No. on your demand; refer to Section
6.3.2 Configuring Port Settings for details.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning System
65
6.4 Configuring Video and Audio Settings
6.4.1 Configuring Video Settings
Steps:
1. Enter the Video Settings interface:
Configuration >Basic Configuration > Video / Audio > Video
Or Configuration > Advanced Configuration > Video / Audio > Video
Figure 6-28 Configure Video Settings
2. Select the Channel No. in the dropdown list you want to configure and select the
Stream Type of the positioning system to main stream (normal) or sub-stream.
The main stream is usually for recording and live viewing with good bandwidth,
and the sub-stream can be used for live viewing when the bandwidth is limited.
Refer to the Section 6.1 Configuring Local Parameters for switching the main
stream and sub-stream for live viewing.
3. You can customize the following parameters for the selected main stream or
sub-stream:
Video Type:
Select the stream type to video stream, or video & audio composite stream. The
audio signal will be recorded only when the Video Type is Video&Audio.
Resolution:
Select the resolution of the video output.
Bitrate Type:
Select the bitrate type to constant or variable.
Video Quality:
When bitrate type is selected as Variable, 6 levels of video quality are selectable.
Frame Rate:
The frame rate is to describe the frequency at which the video stream is updated
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
66
and it is measured by frames per second (fps). A higher frame rate is
advantageous when there is movement in the video stream, as it maintains image
quality throughout.
Max. Bitrate:
Set the max. bitrate to 32~16384 Kbps. The higher value corresponds to the
higher video quality, and the higher bandwidth is required as well.
Video Encoding:
The Video Encoding standard can be set to H.264 or MJPEG.
Profile:
You can set the profile level to High Profile, Main Profile or Basic Profile.
I Frame Interval:
Set the I-Frame interval from 1 to 400.
SVC:
SVC is a video encoding technology. It extracts frames from the original video and
sends these frames to a video recorder which also supports SVC function when
the network bandwidth is insufficient.
4. Click
to save the settings.
6.4.2 Configuring Audio Settings
Steps:
1. Enter the Audio Settings interface
Configuration > Basic Configuration > Video / Audio > Audio
Or Configuration > Advanced Configuration > Video / Audio > Audio
Figure 6-29 Audio Settings
2. Configure the following settings.
Audio Encoding: G.722.1, G.711ulaw, G.711alaw, MP2L2 and G.726 selectable.
Audio Stream Bitrate: When the Audio Encoding is selected as MP2L2, you can
configure the Audio Stream Bitrate in the dropdown list. The greater the value is,
the better the audio quality will be.
Audio Input: When an intercom is connected to the positioning system, you
need to set this option to LineIn. When a microphone is connected to the
positioning system, you need to set this option to MicIn.
Input Volume: Slid the bar to turn up/down the volume. The value ranges from 0
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
67
to 100.
Environmental Noise Filter: When the monitoring environment is very noisy, you
can enable this function to reduce part of the noise.
3. Click
to save the settings.
6.4.3 Configuring ROI Settings
Before you start:
ROI (Region of Interest) encoding is used to enhance the quality of images which are
specified in advance.
Enter the RIO Settings interface:
Configuration > Advanced Configuration > Video / Audio > ROI
Figure 6-30 Region of Interest
Channel No.:
Select the Channel No. in the dropdown list, and the ROI area can be set for the
Camera 1 and Camera 2 respectively.
Stream Type:
You can set the ROI function for main stream or substream. Select a stream type and
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
68
then configure the ROI settings.
Fixed Region: The fixed region encoding is the ROI encoding for the manually
configured area. And you can choose the Image Quality Enhancing level for ROI
encoding, and you can also name the ROI area.
Steps:
1. Select a Region No..
2. Check the checkbox of Enable under Fixed Region.
3. Select the region from the dropdown list for ROI settings. There are four fixed
regions selectable.
4. Click the
button, and then click-and-drag the mouse to draw the
region of interest on the live video.
5. Adjust the ROI level from 1 to 6. The higher the value, the better image quality
in the red frame.
6. Enter a Region Name and click Save to save the settings.
6.5 Configuring Image Settings
6.5.1 Configuring Display Settings
Purpose:
You can set the image quality of the positioning system, including brightness,
contrast, saturation, sharpness, etc.
The parameters in Display Settings interface vary depending on the models of
positioning system.
You can double click the live view to enter full screen mode and double click it
again to exit.
Steps:
1. Enter the Display Settings interface:
Configuration > Basic Configuration> Image> Display Settings
Or Configuration > Advanced Configuration> Image> Display Settings
2. You can select the Mounting Scenario in the dropdown list with different
predefined image parameters.
3. Set the image parameters of the positioning system.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
69
Setting the Channel Camera 1
Select the Channel No. to Camera 1.
Figure 6-31 Display Settings-Optical Channel
Image Adjustment
Brightness
This feature is used to adjust brightness of the image. The value ranges from 0 to
100.
Contrast
This feature enhances the difference in color and light between parts of an image.
The value ranges from 0 to 100.
Saturation
This feature is used to adjust color saturation of the image. The value ranges from 0
to 100.
Sharpness
Sharpness function enhances the detail of the image by sharpening the edges in the
image. The value ranges from 0 to 100.
This function varies depending on the models of positioning system.
Exposure Settings
Exposure Mode
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
70
The Exposure Mode can be set to Auto, Iris Priority, Shutter Priority, Manual.
Auto:
The iris, shutter and gain values will be adjusted automatically according to the
brightness of the environment.
Iris Priority:
The value of iris needs to be adjusted manually. The shutter and gain values will
be adjusted automatically according to the brightness of the environment.
Figure 6-32 Manual Iris
Shutter Priority:
The value of shutter needs to be adjusted manually. The iris and gain values will
be adjusted automatically according to the brightness of the environment.
Figure 6-33 Manual Shutter
Gain Priority:
The value of gain needs to be adjusted manually. The shutter and iris values will
be adjusted automatically according to the brightness of the environment.
Figure 6-34 Manual Gain
Manual:
In Manual mode, you can adjust the values of Gain, Shutter, Iris manually.
This function varies depending on the models of positioning system.
Limit Gain
This feature is used to adjust gain of the image. The value ranges from 0 to 100.
Slow Shutter
This function can be used in underexposure condition. It lengthens the shutter time
to ensure full exposure. The slow shutter value can be set to Slow Shutter*2, *4, *6,
*12, *16, *24 and *32.
Figure 6-35 Slow Shutter
Focus Settings
Focus Mode
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
71
The Focus Mode can be set to Auto, Manual, Semi-auto.
Auto:
The positioning system focuses automatically at any time according to objects in
the scene.
Semi-auto:
The positioning system focuses automatically only once after panning, tilting and
zooming.
Manual:
In Manual mode, you need to use
on the control panel to focus
manually.
Min. Focus Distance
This function is used to limit the minimum focus distance.
The minimum focus value varies depending on the models of positioning system.
Day/Night Switch
The IR light related function introduced below is supported by IR positioning
systems only.
Day/Night Switch
The Day/Night Switch mode can be set to Auto, Day, Night, and Scheduled.
Auto:
In Auto mode, the day mode and night mode can switch automatically
according to the light condition of environment. The switching sensitivity can
be set to 1-3.
Figure 6-36 Auto Mode Sensitivity
Day:
In Day mode, the positioning system displays color image. It is used for normal
lighting conditions.
Night:
In Night mode, the image is black and white. Night mode can increase the
sensitivity in low light conditions.
Schedule:
In Schedule mode, you can set the time schedule for day mode as shown in
Figure 6-37. The rest time out of the schedule is for night mode.
This function varies depending on the models of positioning system.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
72
Figure 6-37 Day Night Schedule
Smart IR
If the IR light is on and the image center is overexposure, you can enable this
function.
IR Light Mode
IR light mode can be set to Auto and you need to adjust the brightness limit of
infrared light manually. Brightness Limit value ranges from 0 to 100.
The IR related functions are supported by the IR positioning system only.
For detailed parameters configuration of IR light, you can enter the OSD menu by
calling the special preset 95.
Backlight Settings
BLC
If there’s a bright backlight, the subject in front of the backlight appears silhouetted
or dark. Enabling BLC (Back Light Compensation) function can correct the exposure of
the subject. But the backlight environment is washed out to white.
WDR (Wide Dynamic Range)
The WDR (Wide Dynamic Range) function helps the camera provide clear images
even under back light circumstances. When there are both very bright and very dark
areas simultaneously in the field of view, WDR balances the brightness level of the
whole image and provide clear images with details.
You can enable or disable the WDR function.
This function varies depending on the models of positioning system.
HLC
HLC (High Light Compensation) makes the camera identify and suppress the strong
light sources that usually flare across a scene. This makes it possible to see the detail
of the image that would normally be hidden.
White Balance
The White Balance mode can be set to Auto, MWB, Outdoor, Indoor, Fluorescent
Lamp, Sodium Lamp and Auto-Track.
Auto:
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
73
In Auto mode, the camera retains color balance automatically according to the
current color temperature.
MWB:
In MWB (Manual White Balance) mode, you can adjust the color temperature
manually to meet your own demand as shown in Figure 6-38.
Figure 6-38 Manual White Balance
Outdoor
You can select this mode when the positioning system is installed in outdoor
environment.
Indoor
You can select this mode when the positioning system is installed in indoor
environment.
Fluorescent Lamp
You can select this mode when there are fluorescent lamps installed near the
positioning system.
Sodium Lamp
You can select this mode when there are sodium lamps installed near the positioning
system.
Auto-Tracking
In Auto-Tracking mode, white balance is continuously being adjusted in real-time
according to the color temperature of the scene illumination.
This function varies depending on the models of positioning system.
Image Enhancement
Digital Noise Reduction
The digital noise reduce function processes the noise in the video signal.
You can set Digital Noise Reduction function to Normal Mode and adjust the Noise
Reduction Level as shown in Figure 6-39. The level ranges from 0 to 100.
Figure 6-39 Digital Noise Reduction-Normal Mode
You can set Digital Noise Reduction function to Normal Mode and adjust the Space
DNR Level and Time DNR Level as shown in Figure 6-40. The level ranges from 0 to
100.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
74
Figure 6-40 Digital Noise Reduction-Expert Mode
This function varies depending on the models of positioning system.
Defog Mode
When there is fog in the image, you can enable this function to get clear image.
EIS
The live view image would be trembled and dim when the camera is shocked slightly
in some monitoring conditions. And the electronic image stabilization (EIS) function is
used to overcome this problem to ensure a steady and clear image.
Video Adjustment
Mirror
If you set the Mirror function to Center, the image will be flipped. It is like the image
in the mirror.
This function varies depending on the models of positioning system.
Video Standard
You can set the Video Standard to 50hz(PAL) or 60hz(NTSC) according to the video
system in your country.
This function varies depending on the models of positioning system.
Capture Mode:
The Capture Mode is selectable to meet the different demands of field of view and
resolution.
Other
Lens Initialization
The lens operates the movements for initialization when you check the check box of
Lens Initialization.
Zoom Limit
You can set Zoom Limit value to limit the maximum value of zooming. The value can
be set to 30, 60, 120, 240 and 480.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
75
This function varies depending on the models of positioning system.
Local Output
You can enable or disable the video output through the BNC interface on your
demand.
Setting the Channel Camera 2
Select the Channel No. to Camera 2.
Image Adjustment
Brightness
This feature is used to adjust brightness of the image. The value ranges from 0 to
100.
Contrast
This feature enhances the difference in color and light between parts of an image.
The value ranges from 0 to 100.
FFC
The FFC (Flat Field Correction) improves the quality in digital imaging. It can remove
artifacts from 2-D images that are caused by variations in the pixel-to-pixel sensitivity
of the detector or by distortions in the optical path. Schedule, Temperature, and OFF
are selectable.
Schedule
You can select the correction interval among “10”, “20”, “30”, “40”, “50”, “60”,
“120”, “180”, and “240” minutes.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
76
Temperature
Camera adjusts the image according to the temperature.
Manual Background Correction
Fully cover the lens with an object (lens cover is recommended) and click the Manual
Background Correction button, and then the positioning system adjusts the image
according to the current environment.
Manual Shutter Correction
Click the Manual Shutter Correction button and then the positioning system adjusts
the image according to the temperature of the camera itself.
AGC Mode
This feature can be selected among Normal, Highlight, and Manual. Normal is
applicable to most of the environment; while it may display less details and
backgrounds when in an environment have obvious dark areas and bright areas.
Highlight is applicable to the highlight environment. If manual is selected for AGC
mode, brightness and contrast can be adjusted.
Image Enhancement
Digital Noise Reduction:
DNR reduces the noise in the video stream. OFF, Normal Mode and Expert Mode are
selectable.
OFF: DNR is disabled.
Normal Mode: Set the DNR level from 0~ 100, and the default value is 50.
Expert Mode: Set the DNR level from both space DNR level [0~100] and time DNR
level [0~100] in Expert Mode.
Palettes
The palettes allow you to select the desired colors. white hot, black hot, fusion 1,
rainbow, fusion 2, ironbow 1, ironbow2, sepia, color 1, color 2, ice fire, rain, red hot,
and green hot are selectable.
DDE
The DDE (Digital Detail Enhancement) can adjust the details of the image. And you
can set it to OFF or Normal mode. And DDE Level can be adjust from 1 to 100 when
in normal mode.
Video Adjustment
Mirror
If you turn the Mirror function on, the image will be flipped. You can set the mirror
direction to Center or disable it.
This function varies depending on the models of positioning system.
Video Standard
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
77
The Video Standard is configurable.
This function varies depending on the models of positioning system.
Capture Mode:
You can set the Capture Mode to OFF and 384*288@25fps.
Digital Zoom
The digital zoom is available for the thermal sensor, there are x2 and X4 selectable.
This function varies depending on the models of positioning system.
Other
Local Output
You can enable or disable the video output through the BNC interface on your
demand.
6.5.2 Configuring OSD Settings
Purpose:
The positioning system supports following on screen displays:
Zoom: Identifies the amount of magnification.
Direction: Displays panning and tilting direction, with the format of PXXX TXXX. The
XXX following P indicates the degrees in pan direction, while the XXX following T
indicates the degrees in tilt position.
Time: Supports for time display.
Preset Title: Identifies preset being called.
Camera Name: Identifies the name of positioning system.
You can customize the on screen display of time.
Steps:
1. Enter the OSD Settings interface:
Configuration > Advanced Configuration > Image > OSD Settings
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
78
Figure 6-41 OSD Settings
2. Check the corresponding checkbox to select the display of positioning system
name, date or week if required.
3. Edit the positioning system name in the text field of Camera Name.
4. Select from the drop-down list to set the time format, date format and display
mode.
5. You can use the mouse to click and drag the text frame
in the live view
window to adjust the OSD position.
Figure 6-42 Adjust OSD Location
6. The font color can also be customized, select the Custom in the drop down list
and select the font color on your demand.
7. Click
to activate above settings.
© Hikvision
79
User Manual of Thermometric Bi-spectrum Network Positioning system
6.5.3 Configuring Text Overlay Settings
Purpose:
You can customize the text overlay.
Steps:
1. Enter the Text Overlay Settings interface:
Configuration > Advanced Configuration > Image > Text Overlay
2. Check the checkbox in front of textbox to enable the on-screen display.
3. Input the characters in the textbox.
4. Use the mouse to click and drag the red text frame
in the live view
window to adjust the text overlay position.
5. Click
.
There are up to 8 text overlays configurable.
Figure 6-43 Text Overlay Settings
6.5.4 Configuring DPC Settings
DPC (Defective Pixel Correction) refers to the function that the camera can correct
the defective pixels on the LCD which are not performing as expected.
© Hikvision
80
User Manual of Thermometric Bi-spectrum Network Positioning system
Figure 6-44 Defective Pixel Correction
Steps:
1. Select the defective pixel using the mouse. And click
2. Click
to adjust the position.
to start correction.
3. (Optional) Click
to cancel the correction.
This function varies depending on the models of positioning system.
6.6 Configuring and Handling Alarms
Purpose:
This section explains how to configure the network positioning system to respond to
alarm events, including motion detection, external alarm input, video loss,
tamper-proof and exception. These events can trigger the alarm actions, such as
Notify Surveillance Center, Send Email, Trigger Alarm Output, etc.
For example, when an external alarm is triggered, the network positioning system
sends a notification to an e-mail address.
6.6.1 Configuring Motion Detection
Purpose:
Motion detection is a feature which can trigger alarm actions and actions of
recording videos when the motion occurred in the surveillance scene.
Steps:
© Hikvision
81
User Manual of Thermometric Bi-spectrum Network Positioning system
1. Enter the motion detection setting interface:
Configuration > Advanced Configuration> Basic Event > Motion Detection
2. The motion detection function is applicable to both the optical channel and the
thermal channel, you need to select the Channel No. in the dropdown list to
configure.
3. Check the checkbox of the Enable Motion Detection to enable this function.
You can check the Enable Dynamic Analysis for Motion checkbox if you want the
detected object get marked with rectangle in the live view.
4. Select the configuration mode as Normal or Expert and set the corresponding
motion detection parameters.
Normal
Figure 6-45 Motion Detection Settings-Normal
(1) Click
. Click and drag the mouse on the live video image to draw a
motion detection area.
(2) Click
to finish drawing.
• You can draw up to 8 motion detection areas on the same image.
• You can click
(3) Move the slider
detection.
Expert
© Hikvision
to clear all of the areas.
to set the sensitivity of the
User Manual of Thermometric Bi-spectrum Network Positioning system
82
Figure 6-46 Motion Detection Settings-Expert
(1) (Available for the optical channel only) Set the Day&Night switch mode, there
are OFF, Auto-Switch and Scheduled-Switch selectable. If the Day&Night
switch mode is enabled, you can configure the detection rule for the day and
night separately.
OFF: Disable the day and night switch.
Auto-Switch: Switch the day and night mode according to the illumination
automatically.
Scheduled-Switch: Switch to the day mode at 6:00 a.m., and switch to the
night mode at 18:00 p.m..
(2) Select Area No. to configure in the dropdown list.
(3) Set the values of sensitivity and proportion of object on area.
Sensitivity: The greater the value is, the easier the alarm will be triggered.
Proportion of Object on Area: When the size proportion of the moving object
exceeds the predefined value, the alarm will be triggered. The less the value is,
the easier the alarm will be triggered.
5. Set the Arming Schedule for Motion Detection.
(1) Click
© Hikvision
in Figure 6-47.
User Manual of Thermometric Bi-spectrum Network Positioning system
83
Figure 6-47 Arming Schedule
(2) Choose the day you want to set the arming schedule as shown in Figure
6-48.
Figure 6-48 Arming Time Schedule
(3) Click
to set the time period for the arming schedule.
(4) (Optional) After you set the arming schedule, you can click
the schedule to other days.
(5) Click
to save the settings.
to copy
The time of each period cannot be overlapped. Up to 8 periods can be
configured for each day.
6. Set the Alarm Actions for Motion Detection.
You can specify the linkage method when an event occurs. The following
contents are about how to configure the different types of linkage method.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
84
Figure 6-49 Linkage Method
Check the checkbox to select the linkage method. Notify surveillance center,
send email, upload to FTP, trigger channel and trigger alarm output are
selectable.
Notify Surveillance Center
Send an exception or alarm signal to remote management software when
an event occurs.
Send Email
Send an email with alarm information to a user or users when an event
occurs.
To send the Email when an event occurs, you need to refer to Section
6.3.11 Configuring Email Settings to set the Email parameters.
Upload to FTP
Capture the image when an alarm is triggered and upload the picture to a
FTP server.
You need a FTP server and set FTP parameters first. Refer to Section
6.3.8 Configuring FTP Settings for setting FTP parameters.
Trigger Channel
Trigger the camera to record a video when an event occurs.
You have to set the recording schedule to realize this function. Please
refer to Section 8.3 Configuring Recording Schedule for settings the
recording schedule.
Trigger Alarm Output
Trigger one or more external alarm outputs when an event occurs.
To trigger an alarm output when an event occurs, please refer to
Section 6.6.4 Configuring Alarm Output to set the alarm output
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
85
parameters.
6.6.2 Configuring Video Tampering Alarm
Purpose:
You can configure the positioning system to trigger the alarm actions when the lens is
covered.
Steps:
1. Enter the video tampering Settings interface:
Configuration > Advanced Configuration > Basic Event > Video Tampering
Figure 6-50 Tampering Alarm
2. The motion detection function is applicable to both the optical channel and the
thermal channel, you need to select the Channel No. in the dropdown list to
configure.
3. Check Enable Video Tampering checkbox to enable the tampering detection.
4. Set the tampering area. Refer to Step 1 in Section 6.6.1 Configuring Motion
Detection.
5. Click
to edit the arming schedule for tampering. The arming schedule
configuration is the same as the setting of the arming schedule for motion
detection. Refer to Step 2 in Section 6.6.1 Configuring Motion Detection.
6. Check the checkbox to select the linkage method taken for the tampering. Notify
surveillance center, send email, trigger channel and trigger alarm output are
selectable. Please refer to Step 3 in Section 6.6.1 Configuring Motion Detection.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
7. Click
86
to save the settings.
6.6.3 Configuring Alarm Input
Steps:
1. Enter the Alarm Input Settings interface:
Configuration > Advanced Configuration> Events > Alarm Input:
2. Choose the alarm input No. and the Alarm Type. The alarm type can be NO
(Normally Open) and NC (Normally Closed).
3. Edit the name in
to set a
name for the alarm input (optional).
Figure 6-51 Alarm Input Settings
4. Click
to set the arming schedule for the alarm input. Refer to Step 2
in Section 6.6.1 Configuring Motion Detection.
5. Check the checkbox to select the linkage method taken for the alarm input. Refer
to Step 3 in Section 6.6.1 Configuring Motion Detection.
6. You can also choose the PTZ linking for the alarm input. Check the relative
checkbox and select the No. to enable Preset Calling, Patrol Calling or Pattern
Calling.
7. You can copy your settings to other alarm inputs.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
8. Click
87
to save the settings.
Figure 6-52 Linkage Method
6.6.4 Configuring Alarm Output
Steps:
1. Enter the Alarm Output Settings interface:
Configuration>Advanced Configuration> Events > Alarm Output
2. Select one alarm output channel in the Alarm Output drop-down list.
3.
4.
5.
Set a name in
for the
alarm output (optional).
The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or
Manual. The delay time refers to the time duration that the alarm output
remains in effect after alarm occurs.
Click
to enter the Edit Schedule Time interface. The time schedule
configuration is the same as the settings of the arming schedule for motion
detection. Refer to Step 2 in Section 6.6.1 Configuring Motion Detection.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
88
Figure 6-53 Alarm Output Settings
6. You can copy the settings to other alarm outputs.
7. Click
to save the settings.
6.6.5 Handling Exception
The exception type can be HDD full, HDD error, network disconnected, IP address
conflicted and illegal login to the positioning systems.
Steps:
1. Enter the Exception Settings interface:
Configuration > Advanced Configuration> Events > Exception
2. Check the checkbox to set the actions taken for the Exception alarm. Refer to
Step 3 in Section 6.6.1 Configuring Motion Detection.
Figure 6-54 Exception Settings
3. Click
© Hikvision
to save the settings.
User Manual of Thermometric Bi-spectrum Network Positioning system
89
6.6.6 Detecting Audio Exception
Purpose:
When you enable this function and audio exception occurs, the alarm actions will be
triggered.
Steps:
1. Enter the video audio exception detection interface:
Configuration > Advanced Configuration > Smart Event > Audio Exception
Detection
Figure 6-55 Audio Exception Detection
2.
3.
4.
Check the checkbox of Audio Loss Detection to enable the audio input exception
detection.
Check the checkbox of Sudden Increase of Sound Intensity Detection checkbox
to enable the sudden rise detection.
Sensitivity: Range [1-100], the smaller the value the more severe the sound
change will trigger the detection.
Sound Intensity Threshold: Range [1-100], it can filter the sound in the
environment, the louder the environment sound, the higher the value should
be. You can adjust it according to the actual environment.
Check the checkbox of Sudden Decrease of Sound Intensity Detection checkbox
to enable the sudden drop detection.
Sensitivity: Range [1-100], the smaller the value the more severe the sound
change will trigger the detection.
5.
Click
6.
is the same as the setting of the arming schedule for motion detection. Refer to
Step 2 in Section 6.6.1 Configuring Motion Detection.
Check the checkbox to select the linkage method taken for audio exception.
© Hikvision
to edit the arming schedule. The arming schedule configuration
User Manual of Thermometric Bi-spectrum Network Positioning system
90
Notify surveillance center, send email, trigger alarm output, etc. are selectable.
Please refer to Step 3 in Section 6.6.1 Configuring Motion Detection.
7. Click
to save the settings.
6.6.7 Detecting Dynamic Fire Source
Purpose:
When you enable this function and fire source is detected, the alarm actions will be
triggered.
Steps:
1. Enter Configuration>Advanced Configuration>System>VCA Resource Type to
select Dynamic Fire Source Detection as VCA Resource Type.
2. Enter the dynamic fire source detection interface:
Configuration > Advanced Configuration > Smart Event > Dynamic Fire Source
Detection
Figure 6-56 Dynamic Fire Source Detection
3.
Check the checkbox of Enable Dynamic Fire Source Detection to enable the
dynamic fire source detection.
The function of dynamic fire source detection can only be enabled for
camera 2.
Sensitivity: Range [1-10], the smaller the value is, the fire source of lower
temperature can be detected.
Dwell Time(s): Range [0-120]. You can set the dwell time of the positioning
system staying the position where detects the fire source when performing
auto scan, patrol, pattern, scheduled task, and park action.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
4.
5.
91
Check the checkbox of Display Fire Source Frame on Stream to display a red
frame around the fire source on stream when fire occurs. (Optional)
Check the checkbox to select the linkage method taken for the alarm input. Refer
to Step 3 in Section 6.6.1 Configuring Motion Detection. In the field of Other
Linkage, you can check the checkbox to enable the alarm output (The alarm
output number varies depending on device ability).
6. Click
to save the settings.
Comment [t1]:
6.6.8 Detecting Ship
Purpose:
When you enable this function and ship is detected, the alarm actions will be
triggered.
Steps:
1. Enter Configuration>Advanced Configuration>System>VCA Resource Type to
select Ship Detection as VCA Resource Type.
2. Enter the ship detection interface:
Configuration > Advanced Configuration > Smart Event > Ship Detection
3. Check the checkbox of Enable Ship Detection to enable the ship detection
function.
4. Check the checkbox of Display Detection Frame on Video to display the frame
and alarm line on stream. (Optional)
5.
6.
7.
The function of ship detection is only supported for some models.
Enter the device height in the textbox as the height of device above the water
level.
Draw the ship detection area and the alarm lines.
(1) Click Draw Area. Click the mouse on the live video image to draw a ship
detection area and right click to finish the drawing. The alarm will be
uploaded when ship is detected in this area.
(2) Click Draw Alarm Line. Click the mouse on the live video to draw an
alarm line and right click to finish the drawing. The device alarms and
counts the ship number when ships are detected in the area and the
ship information will be displayed on the right.
Make sure the alarm line is longer than the width of ship detection
area.
Check the checkbox to select the linkage method taken for the alarm input. Refer
to Step 3 in Section 6.6.1 Configuring Motion Detection. In the field of Other
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
92
Linkage, you can check the checkbox to enable the alarm output (The alarm
output number varies depending on device ability).
8. Click
to save the settings.
6.7 Temperature Measurement
Purpose:
When you enable this function, it measures the actual temperature of the spot being
monitored. The device alarms when temperature exceeds the temperature threshold
value.
Before You Start:
Enter Configuration > Advanced Configuration > System > VCA Resource Type to
select Temperature Measurement + Behavior Analysis as VCA Resource Type.
6.7.1 Temperature Measurement Configuration
Steps:
1. Enter Configuration > Advanced Configuration > Temperature Measurement
Configuration.
Figure 6-57 Dynamic Fire Source Detection
2.
Check the checkboxes of the interface to set the temperature measurement
configurations.
Enable Temperature Measurement: Check the checkbox to enable
temperature measurement function.
Display Temperature Info. on Stream: Check the checkbox to display
temperature information in live view.
Add Original Data on Capture: Check the checkbox to add original data on
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
93
capture.
Add Original Data on Stream: Check the checkbox to add original data on
stream.
Data Refresh Interval: Select the data refresh interval from 1s to 5s.
Unit: Display temperature with Degree Celsius (°C)/Degree Fahrenheit
(°F)/Degree Kelvin (K .
Temperature Range: Set the temperature range.
Clcik Save to save the settings .
)
3.
6.7.2 Temperature Measurement and Alarm
Purpose:
This function is used for measuring the temperature of detected spot and the device
compares temperature of selected regions and alarms.
Steps:
1. Enter Configuration > Advanced Configuration > Temperature Measurement
and Alarm.
2. Adjust the image to the scene for temperature measurement with the PTZ
control panel. Save current scene as certain preset.
•
•
3.
You can set the preset in live view interface before and call the preset in the
temperature measurement and alarm interface.
You can set/ call/ clear the preset in temperature measurement interface.
Set the alarm rule: Select a temperature measurement rule from the rule list and
configure the parameters.
Name: You can customize the rule name.
Type: Select point, line, or frame as rule type.
Emissivity: Set the emissivity of your target. Note: The emissivity of each
object is different.
Distance (m): The straight-line distance between the target and the device.
Reflective Temperature: If there is any target with high emissivity in the scene,
check the checkbox and set the reflective temperature to correct the
temperature. If no such target exists, uncheck the checkbox.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
94
Figure 6-58 Temperature Measurement Configuration
4.
Click
in the list to show the alarm rule interface.
Alarm Rule: The alarm rule varies according to different types. The rule is to
compare the temperature information of two selected regions. For targets set
by frame, the rules include: Max. Temperature is Higher than, Max.
Temperature is Lower than, Min. Temperature is Higher than, Min.
Temperature is Lower than, Average Temperature is Higher than, Average
Temperature is Lower than, Temperature Difference is Higher than, and
Temperature Difference is Lower than. For targets set by line, the rules
include Max. Temperature, Min. Temperature, and Average Temperature. For
targets set by point, the rules are distinguished by Average Temperature.
Pre-Alarm Temperature and Alarm Temperature: Set the pre-alarm
temperature and alarm temperature, the device sends pre-alarm when its
rule temperature exceeds pre-alarm temperature and sends alarm when its
rule temperature exceeds alarm temperature.
Tolerance Temperature: Set the tolerance temperature and the device judges
whether the triggered alarm stops until the device temperature/temperature
difference is lower than rule temperature by tolerance temperature. For
example, set tolerance temperature as 3°C, set alarm temperature as 55°C,
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
5.
95
and set pre-alarm temperature as 50°C. The device sends pre-alarm when its
temperature reaches 50°C and it alarms when its temperature reaches 55°C
and only when the device temperature is lower than 52°C will the alarm be
cancelled.
Draw the Target Region: Select the rule and draw the corresponding
frame/line/point. Click
to draw the point. Click
to draw the line. Click
to draw the frame.
6.
7.
8.
Set Temperature Difference Alarm: Click Temperature Difference Alarm to enter
the temperature difference alarm interface, up to four temperature difference
alarms can be set.
Temperature Difference Alarm only applies to the targets set by frame.
Set Alarm Linkage: Click Alarm Linkage to enter the alarm linkage interface and
set the linkage methods.
Click Save to save the settings.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
96
Chapter 7 VCA Configuration
Purpose:
You can do intelligent analysis, such as behavior analysis, with the positioning system.
Multiple rules can be configured for different requirements.
The VCA function only supported by the thermal channel.
7.1 VCA Resource Configuration
Purpose:
Before using the VCA function of the camera, you should select the VCA resource
type first. To use Temperature Measurement and Behavior Analysis, select
Temperature Measurement and Behavior Analysis. To use Dynamic Fire Source
Detection function, select Dynamic Fire Source Detection. To use Ship Detection
function, select Ship Detection.
Steps:
1. Enter the VCA Resource Type interface:
Configuration > Advanced Configuration > System > VCA Resource Type
Figure 7-1 VCA Information
2. Check the checkbox to enable the VCA resource type.
3. The system reboots and the selected VCA resource will be enabled.
Once you select any of the resources, the other VCA rules cannot be enabled.
7.2 Configuring VCA Information
Steps:
1. Enter the VCA Information Configuration interface:
Configuration > VCA Configuration > VCA Info.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
97
Figure 7-2 VCA Information
2. Tick the checkbox to enable the Intelligent Analysis. And you can view the current
version for the behavior analysis.
3. Set the display information:
If you select to display the target info and rule info on the alarm picture are
supported; you can enable the functions by ticking the corresponding
checkbox on your demand.
And if you tick the checkbox of display target info and rule on stream, the
information will be added to the video stream, and the overlay will be
displayed if you get live view or play back by the VS Player.
4. Set the Snapshot:
You can configure the Notify Surveillance Center function which is used for
uploading the picture to the surveillance center when and VCA alarm occurs.
You can also set the quality and resolution of the picture separately.
5. Click
to save the settings.
7.3 Advanced Configuration
All the parameters for both behavior analysis and face capture are collected in the
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
98
advanced configuration page. You can configure these parameters for different VCA
types on your demand.
Steps:
1. Enter the Advanced Configuration interface:
Configuration > VCA Configuration > Advanced Configuration
Figure 7-3 Advanced Configuration
2. Adjust the Detection Parameters.
Detection Sensitivity: Range [0-4], the higher the sensitivity is, the easier the
target will be detected.
Background Update Rate: Range [0-4], if a detected target remains in the
monitoring scene for a certain time, the system will count the target as the
background automatically. The greater the value is, the faster the target will be
counted as the background.
Minimum Target Size: Range [0-4], The system will filter out the object smaller
than the minimum target size.
Displacement Constraint for Target Generation: Range [0-4], the higher the
value is, the slower the target is generated, and the higher accuracy the analysis
will get.
Light Change Suppression: Check the checkbox to suppress the impact caused
by the illumination change.
3. Adjust the Tracking Parameters.
Post-Tracking: Range [2-600], you can configure the tracking duration after the
target is still.
Force Tracking: Check the checkbox to enable the function to prevent the object
to be blocked. After the function being enabled, the positioning system will
continue locating and tracking the blocked target.
Restore Default: Click
Restart VCA: Click
© Hikvision
to restore the parameters to the default.
to restart the VCA function.
User Manual of Thermometric Bi-spectrum Network Positioning system
99
7.4 Behavior Analysis
Purpose:
The positioning system supports patrol tracking for multiple scenes. At most 8 rules
can be configured for a single scene. You can configure the rules for the scene on
your demand.
Steps:
1. Configure the VCA Info: For details, see 7.2.
2. Configure the Zooming Ratio parameters: Set the appropriate tracking zooming
ratio with the PTZ control panel. Click on
button to save the settings.
The optical camera will track the target when the VCA rule is triggered which is
configured on the thermal camera.
Figure 7-4 Zoom Ratio
3. Configure the Scene:
Go to VCA Configuration> Scene Configuration
At most 10 scenes can be added. Different rules and properties can be configured
for each scene.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
100
Figure 7-5 Scene Parameters
Create a Scene:
1) Add New Scene: Click
to create a new scene.
2) Control the PTZ to get the required scene.
3) Set the scene parameters:
Scene Name: Enter a custom scene name.
Patrol Sequence: Set the sequence for the scene when doing patrol tracking.
If the sequence is selected as 0, this scene will not be configured for patrol
tracking.
Duration: Set the dwell time of the scene when doing patrol tracking. The
intelligent analysis will be enabled during the period. If the alarm is triggered,
the positioning system will start to track automatically.
Track: Check the checkbox to enable the auto tracking function for the scene.
Once the thermal channel detects target, the optical channel auto tracks the
target.
Tracking Duration: Set the duration of the auto track. If the value is set as 0,
the tracking duration will not be limited.
Limited Tracking: You can check the checkbox to enable/disable the function.
If the function is enabled, you can set the limited position for the tracking.
4) Click
to save the settings.
Rule Configuration:
At most 8 rules can be configured for a single scene. Follow the steps below
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
101
to configure the rule for the scene.
1) Click the Rule tab to enter the rule settings interface.
2) Create new rule: Click on the button
to add a new rule.
3) Select rule type: Click the dropdown menu to select the rule type. Line
Crossing, Intrusion, Region Entrance, and Region Exiting are selectable.
Figure 7-6 Rule List
4) Configure the rule area: Click the Draw Line or Draw Area button on the tool
bar of the live view panel. Click the mouse on the live view panel. Right click
the mouse to finish drawing. For details, see 7.5 Rule Configuration
Demonstration.
5) Configure the filtering size: The filtering function is supported for all rules.
You can set the minimum and maximum size of the object needs to be
filtered. The system will only detect the object in a size between the
configured minimum and maximum value. For details, see7.5 Rule
Configuration Demonstration.
6) Enable rules: Check the Enable checkbox of each rule in the rule list to
enable the rule.
7) Click
to save the settings.
Create multiple rules: You can create more rules by repeating the above
steps.
Configure Arming schedule:
1) Click the Arming Schedule tab.
2) Select a rule from the rule list.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
102
Figure 7-7 Arming Schedule
3) Click on the Edit button to edit the arming time segment.
Figure 7-8 Schedule Time
You can select to copy the settings to whole week or are specific days of the
week. At most 8 segments can be configured.
4) Click
to save the settings.
Configure Arming schedule:
1) Click the Alarm Linkage tab.
2) Select a rule from the rule list.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
103
Figure 7-9 Alarm Linkage
3) Check the checkbox of corresponding linkage actions to enable it.
4. Advanced Configuration: For details, see section 7.3 Advanced Configuration.
Click Save to save the settings.
7.5 Rule Configuration Demonstration
Purpose:
This section provides detailed configuration steps for each rule.
7.5.1 Line Crossing
Purpose:
This function can be used for detecting people, vehicles and objects traversing a set
virtual plane. The traversing direction can be set as bidirectional, from left to right or
from right to left. The alarm will be triggered if the rule is broken.
Steps:
1. Create new rule: Click on the button
to add a new rule.
2. Select rule type: Click the dropdown menu and select Line Crossing as the rule
type.
Figure 7-10 Select Rule Type
3. (Optional) Configure the size filter, if you want to narrow the detection target to
a desired range.
1) Check the checkbox of the Filter by, and only filer by pixel is available.
2) Click the
© Hikvision
button and draw a rectangle on the live view image as
User Manual of Thermometric Bi-spectrum Network Positioning system
104
the Min. size filter.
3) Click the
button and draw a rectangle on the live view image as
the Max. size filter.
4. Configure the rule area:
Click
on the tool bar of the live view panel. Specify a point of the
line by clicking the mouse on the live view image, and then specify the other
one.
Figure 7-11 Draw Line
5. Click the dropdown menu in the rule list to select the crossing direction.
6. Enable rules: Check the Enable checkbox of each rule in the rule list to enable
the rule.
7. Click
to save the settings.
7.5.2 Intrusion
Purpose:
This function can be used for detecting whether there are people, vehicles and
objects intrude into the pre-defined region longer than the set duration. The alarm
will be triggered if the rule is broken.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
105
Steps:
1. Create new rule: Click on the button
to add a new rule.
2. Select rule type: Click the dropdown menu and select Intrusion as the rule type.
3. Configure the filtering size: for details, see step 3 in section 7.5.1 Line Crossing.
4. Configure the rule area:
Click
on the tool bar of the live view panel. Click the mouse on the
live view image to specify a corner of the area. After you specify all the corners,
right click the mouse to connect the first corner and the last corner, which
means the polygonal area is drawn.
Figure 7-12 Draw Area
5. Set the duration from 1 to 100.
6. Enable rules: Check the Enable checkbox of each rule in the rule list to enable
the rule.
7. Click
to save the settings.
7.5.3 Region Entrance
Purpose:
This function can be used for detecting people, vehicles and objects entering the
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
106
pre-defined region. The alarm will be triggered if the rule is broken.
Steps:
1. Create new rule: Click on the button
to add a new rule.
2. Select rule type: Click the dropdown menu and select Region Entrance as the
rule type.
3. Configure the rule area:
Click
on the tool bar of the live view panel. Click the mouse on the
live view panel. Right click the mouse to finish drawing.
4. Configure the filtering size: for details, see step 3 in section 7.5.1 Line Crossing.
5. Enable rules: Check the Enable checkbox of each rule in the rule list to enable
the rule.
6. Click
to save the settings.
7.5.4 Region Exiting
Purpose:
This function can be used for detecting people, vehicles and objects exiting the
pre-defined region. The alarm will be triggered if the rule is broken.
Steps:
1. Create new rule: Click on the button
to add a new rule.
2. Select rule type: Click the dropdown menu and select Region Exiting as the rule
type.
3. Configure the rule area:
Click
on the tool bar of the live view panel. Click the mouse on the
live view panel. Right click the mouse to finish drawing.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
107
Figure 7-13 Draw Area
4. Configure the filtering size: for details, see step 3 in section 7.5.1 Line Crossing.
5. Enable rules: Check the Enable checkbox of each rule in the rule list to enable
the rule.
6. Click
© Hikvision
to save the settings.
User Manual of Thermometric Bi-spectrum Network Positioning System
108
Chapter 8 Record Settings
Before you start:
To configure record settings, please make sure that you have the network storage
device within the network or the storage card has been inserted in the corresponding
card slot. Refer to the installation guide for the location of the storage card slot.
8.1 Configuring NAS Settings
Before you start:
The network disk should be available within the network and properly configured to
store the recorded files, log files, etc.
Steps:
1. Enter the NAS (Network-Attached Storage) Settings interface:
Configuration > Advanced Configuration > Storage > NAS
2. Select the NAS type as NFS or SMB/CIFS. If you select SMB/CIFS, you need to enter
the User Name and Password.
Figure 8-1 Select NAS Type
3. Enter the IP address of the network disk. The default NFS storage format of file
path is /dvr/test as shown in Figure 8-2. And the default SMB/CIFS storage format
of file path is /test.
Figure 8-2 Add Network Disk
4. Click
to add the network disk.
Up to 8 NAS disks can be connected to the positioning system.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
109
8.2 Initializing and Configuring Storage
Steps:
1. Initialize the local disk or added network disk.
(1) Enter the HDD Settings interface (Advanced Configuration > Storage >
Storage Management), in which you can view the capacity, free space, status,
type and property of the disk.
(2) If the status of the disk is Uninitialized as shown in Figure 8-3, check the
corresponding checkbox to select the disk and click
to start
initializing the disk.
Figure 8-3 Initialize Disk
Figure 8-4 Initializing
When the initialization completed, the status of disk will become Normal as
shown in Figure 8-5.
Figure 8-5 View Disk Status
2. Configure the quota for saving the video and picture.
Enter the percentage for picture and record in the text filed, and the total
percentage must be 100%.
Figure 8-6 Setting Quota
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
110
8.3 Configuring Recording Schedule
Before you start:
Please make sure a local storage card is inserted in the positioning system or the
network storage is added to the positioning system, and the
Purpose:
There are two kinds of recording for the positioning systems: manual recording and
scheduled recording. For the manual recording, refer to Section 4.4 Recording and
Capturing Pictures Manually. In this section, you can follow the instructions to
configure the scheduled recording. By default, the record files of scheduled recording
are stored in the SD card (if supported) or in the network disk.
Steps:
1. Enter the Record Schedule Settings interface:
Configuration > Advanced Configuration> Storage > Record Schedule
Figure 8-7 Recording Schedule Interface
2. Check the checkbox of Enable Record Schedule to enable scheduled recording.
3. Set the record parameters of the positioning system.
Figure 8-8 Record Parameters
Pre-record: The time you set to start recording before the scheduled time or
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
111
the event. For example, if an alarm triggers recording at 10:00, and the
pre-record time is set as 5 seconds, the positioning system starts to record at
9:59:55.
The Pre-record time can be configured as No Pre-record, 5 s, 10 s, 15 s, 20 s,
25 s, 30 s or not limited.
The pre-record time changes according to the video bitrate.
Post-record: The time you set to stop recording after the scheduled time or
the event. For example, if an alarm triggered recording ends at 11:00, and the
post-record time is set as 5 seconds, the positioning system records until
11:00:05.
The Post-record time can be configured as 5 s, 10 s, 30 s, 1 min, 2 min, 5 min
or 10 min.
The Pre-record and Post-record parameters vary depending on the
positioning system model.
Overwrite: If you enable this function and the HDD is full, the new record
files overwrite the oldest record files automatically.
Recording Stream: You can select the stream type for recording; Main stream
and Sub Stream are selectable. If you select the sub stream, you can record
for a longer time with the same storage capacity.
4. Click
to edit the record schedule.
Figure 8-9 Record Schedule
5. Choose the day to set the record schedule.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
112
(1) Set all-day record or segment record:
If you want to configure the all-day recording, please check the All Day
checkbox.
If you want to record in different time sections, check the Customize
checkbox. Set the Start Time and End Time.
(2)
The time of each segment cannot be overlapped. Up to 8 segments can
be configured for each day.
Select a Record Type. The record type can be Continuous, Motion Detection,
Alarm, Motion | Alarm, Motion & Alarm, Face Detection, Intrusion Detection,
Line Crossing Detection, Audio Exception Detection and All events.
Continuous
If you select Continuous, the video will be recorded automatically according
to the time of the schedule.
Record Triggered by Motion Detection
If you select Motion Detection, the video will be recorded when the motion
is detected.
Besides configuring the recording schedule, you have to set the motion
detection area and check the checkbox of Trigger Channel in the Linkage
Method of Motion Detection Settings interface. For detailed information,
please refer to the Step 1 in the Section 6.6.1 Configuring Motion Detection.
Record Triggered by Alarm
If you select Alarm, the video will be recorded when the alarm is triggered
via the external alarm input channels.
Besides configuring the recording schedule, you have to set the Alarm Type
and check the checkbox of Trigger Channel in the Linkage Method of Alarm
Input Settings interface. For detailed information, please refer to Section
6.6.3 Configuring Alarm Input.
Record Triggered by Motion & Alarm
If you select Motion & Alarm, the video will be recorded when the motion
and alarm are triggered at the same time.
Besides configuring the recording schedule, you have to configure the
settings on the Motion Detection and Alarm Input Settings interfaces.
Please refer to Section 6.6.1 and Section 6.6.3 for detailed information.
Record Triggered by Motion | Alarm
If you select Motion | Alarm, the video will be recorded when the external
alarm is triggered or the motion is detected.
Besides configuring the recording schedule, you have to configure the
settings on the Motion Detection and Alarm Input Settings interfaces.
Please refer to Section 6.6.1 and Section 6.6.3 for detailed information.
Record Triggered by VCA Recording
If you select VCA Recording, the video will be recorded when the VCA
detection is triggered.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
113
Besides configuring the recording schedule, you have to configure the
settings on the VCA Configuration interface. Please refer to Chapter 7 for
detailed information.
Record Triggered by Audio Exception Detection
If you select Audio Exception Detection, the video will be recorded when
the audio exception is detected.
Besides configuring the recording schedule, you have to configure the
settings on the Audio Exception Detection interface. Please refer to Section
6.6.6 for detailed information.
Record Triggered by All Events
If you select All Events, the video will be recorded when any event is
detected.
(3) Check the checkbox
and click
to copy settings of this
day to the whole week. You can also check any of the checkboxes before the
date and click
.
(4) Click
to save the settings and exit the Edit Record Schedule
interface.
6. Click
to save the settings.
8.4 Configuring Snapshot Settings
Purpose:
You can configure the scheduled snapshot and event-triggered snapshot. You can
upload the captured pictures to a FTP server.
Basic Settings
Steps:
1. Enter the Snapshot Settings interface:
Configuration > Advanced Configuration > Storage > Snapshot
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
114
Figure 8-10 Snapshot Settings
2. Check the Enable Timing Snapshot checkbox to enable continuous snapshot,
and configure the schedule of timing snapshot. Check the Enable
Event-triggered Snapshot checkbox to enable event-triggered snapshot.
3. Select the quality of the snapshot.
4. Set the time interval between two snapshots.
5. Click
to save the settings.
Uploading to FTP
Please make sure that the FTP server is online.
You can follow below configuration instructions to upload the snapshots to FTP.
Upload continuous snapshots to FTP
Steps:
1) Check the Enable Timing Snapshot checkbox.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
2) Configure the FTP settings and check
115
checkbox in FTP
Settings interface. Please refer to Section 6.3.8 Configuring FTP Settings for more
details to configure FTP parameters.
Upload event-triggered snapshots to FTP
Steps:
1) Check the Enable Event-triggered Snapshot checkbox.
2) Configure the FTP settings and check
checkbox in FTP
Settings interface. Please refer to Section 6.3.8 Configuring FTP Settings for more
details to configure FTP parameters.
3) Check
checkbox in Motion Detection Settings or Alarm Input
interface. Please refer to Step 3 in Section 6.6.1 Configuring Motion Detection.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning System
116
Chapter 9 Playback
Purpose:
This section explains how to view the remotely recorded video files stored in the
network disks.
Task 1: To play back the video files
Steps:
1. Click
on the menu bar to enter playback interface.
Figure 9-1 Playback Interface
2. Select the date and click
.
Figure 9-2 Search Video
3. Click
to play the video files found on this date.
© Hikvision
117
User Manual of Thermometric Bi-spectrum Network Positioning system
The toolbar on the bottom of Playback interface can be used to control playing
process.
Figure 9-3 Playback Toolbar
Table 9-1 Description of the buttons
Button
Operation
Button
/
Play/Pause
Stop
Speed down
Speed up
Playback by frame
Capture a picture
/
/
Download video files
Operation
Audio on and adjust
volume/Mute
Start/Stop clipping
video files
Download captured
pictures
Display playback
status
You can choose the file paths locally for downloaded playback video files and
pictures in Local Configuration interface. Please refer to Section 6.1
Configuring Local Parameters for details.
Drag the progress bar with the mouse to locate the exact playback point. You can
also input the time and click
time field. You can also click
to locate the playback point in the Set playback
to zoom out/in the progress bar.
Figure 9-4 Set Playback Time
Figure 9-5 Progress Bar
The different colors of the video on the progress bar stand for the different video
types as shown in Figure 9-6.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
118
Figure 9-6 Video Types
Task 2: To download the video files
Steps:
1. Click
on the playback interface. The pop-up menu is shown in Figure 9-7.
2. Set the start time and end time. Click Search. The corresponding video files are
listed on the left.
Figure 9-7 Video Downloading interface
3. Check the checkbox in front of the video files that you need to download.
4. Click
to download the video files.
The progress ratio
You can click
The total number
displays the downloading ratio of the video file.
to stop downloading.
displays the amount of the video files.
Task 3: To download the captured pictures
Steps:
1. Click
on the playback interface. The pop-up menu is shown in Figure 9-8.
2. Set the linkage type of capturing the pictures as timing, alarm, motion, etc..
3. Set the start time and end time. Click Search. The corresponding picture files are
listed on the left.
4. Check the checkbox in front of the files that you need to download.
5. Click
© Hikvision
to download the files.
User Manual of Thermometric Bi-spectrum Network Positioning system
Figure 9-8 Picture Downloading interface
© Hikvision
119
User Manual of Thermometric Bi-spectrum Network Positioning System
120
Chapter 10 Log Searching
Purpose:
The operation, alarm, exception and information of the positioning system can be
stored in log files. You can also export the log files on your demand.
Before you start:
Please configure network storage for the positioning system or insert a SD card in the
positioning system.
Steps:
1. Click
on the menu bar to enter log searching interface.
Figure 10-1 Log Searching Interface
2. Set the log search conditions to specify the search, including the Major Type,
Minor Type, Start Time and End Time as shown in Figure 10-2.
3. Click
to search log files. The matched log files will be displayed on
the Log interface.
Figure 10-2 Log Searching
4. To export the log files, click
© Hikvision
to save the log files in your computer.
User Manual of Thermometric Bi-spectrum Network Positioning System
121
Chapter 11 Others
11.1 Managing User Accounts
Enter the User Management interface:
Configuration >Basic Configuration> Security > User
Or Configuration > Advanced Configuration> Security > User
The admin user has access to create, edit or delete other accounts. Up to 32 user
accounts can be created.
Figure 11-1 User Information
Add a User
Steps:
1. Click
to add a user.
2. Input the new User Name, select Level and input Password.
The level indicates the permissions you give to the user. You can define the
user as Operator or User.
3. In the Basic Permission field and Camera Configuration field, you can check or
uncheck the permissions for the new user.
4. Click
© Hikvision
to finish the user addition.
122
User Manual of Thermometric Bi-spectrum Network Positioning system
Figure 11-2 Add a User
Modify a User
Steps:
1. Click to select the user from the list and click
.
2. Modify the User Name, Level or Password.
3. In the Basic Permission field and Camera Configuration field, you can check or
uncheck the permissions.
4. Click
to finish the user modification.
Figure 11-3 Modify a User
© Hikvision
123
User Manual of Thermometric Bi-spectrum Network Positioning system
Delete a User
Steps:
1. Click the user name you want to delete and click
2. Click
.
on the pop-up confirmation box to delete the user.
11.1.1 Deleting a User
Steps:
3. Click the user name you want to delete and click
4. Click
.
on the pop-up confirmation box to delete the user.
11.2 Configuring RTSP Authentication
Purpose:
You can specifically secure the stream data of live view.
Steps:
1. Enter the RTSP Authentication interface:
Configuration> Advanced Configuration> Security > Authentication
Figure 11-4 RTSP Authentication
2. Set the authentication mode for each authentication type.
RTSP Authentication: Select the authentication mode as basic or disable in
the dropdown list to enable or disable the RTSP authentication.
WEB Authentication: Select the authentication mode as basic or digest in
the dropdown list.
3. Click
© Hikvision
to save the settings.
User Manual of Thermometric Bi-spectrum Network Positioning system
124
11.3 Configuring Anonymous Visit
When you enable this function, you can log into the camera without a username and
password.
In login interface, check the Anonymous checkbox and click Login to enter the
camera as shown in Figure 11-6.
Figure 11-5 Anonymous Login
Figure 11-6 Login Interface
11.4 Configuring IP Address Filter
With this function on, the camera allows certain IP addresses whether to log in or
not.
Filter Type
Description
Forbid the IP addresses added in the IP Address
Forbidden
Filter interface to log in.
Allow only the IP addresses added in the IP
Allowed
Address Filter interface to log in.
Figure 11-7 IP Address Filter
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
125
11.5 Configuring Security Service Settings
Steps:
1. Enter the Security Service interface:
Configuration> Advanced Configuration> Security > Security Service
Figure 11-8 Security Service
2. Check the checkbox to enable the corresponding function.
Enable Telnet: Telnet is a network protocol used on the Internet or local area
networks to provide a bidirectional interactive text-oriented communication
facility using a virtual terminal connection.
Enable SSH: Enabling SSH (Secure Shell) function is to encrypt and compress the
data and to reduce the transmission time.
11.6 Viewing Device Information
Enter the Device Information interface:
Configuration > Basic Configuration> System > Device Information
Or Configuration > Advanced Configuration> System > Device Information
In the Device Information interface, you can edit the Device Name.
Other information of the network positioning system, such as Model, Serial No.,
Firmware Version, Encoding Version, Number of Channels, Number of HDDs, Number
of Alarm Input and Number of Alarm Output are displayed. The information cannot
be changed in this menu. It is the reference for maintenance or modification in
future.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
Figure 11-9 Device Information
11.7 Maintenance
11.7.1 Rebooting the Positioning system
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or Configuration > Advanced Configuration> System > Maintenance:
2. Click
to reboot the network positioning system.
Figure 11-10 Reboot the Device
11.7.2 Restoring Default Settings
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or Configuration > Advanced Configuration> System > Maintenance
2.
Click
© Hikvision
or
to restore the default settings.
126
User Manual of Thermometric Bi-spectrum Network Positioning system
Clicking
127
restores all the parameters to default settings including
the IP address and user information. Please use this button with caution.
Figure 11-11 Restore Default Settings
11.7.3 Importing/Exporting Configuration File
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or Configuration > Advanced Configuration> System > Maintenance
2.
Click
to select the local configuration file and then click
to
start importing configuration file.
You need to reboot the positioning system after importing configuration file.
3.
Click
and set the saving path to save the configuration file in local
storage.
Figure 11-12 Import/Export Configuration File
11.7.4 Upgrading the System
Steps:
1. Enter the Maintenance interface:
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
128
Configuration > Basic Configuration> System > Maintenance
Or Configuration > Advanced Configuration> System > Maintenance
2. Select Firmware or Firmware Directory.
Firmware: when you select Firmware, you need to find the firmware in your
computer to upgrade the device.
Firmware Directory: You need to find the directory where the firmware
locates. The device can find the firmware in the directory automatically.
3.
Click
to select the local upgrade file and then click
to start
remote upgrade.
The upgrading process will take 1 to 10 minutes. Please don't disconnect
power of the positioning system during the process. The positioning system
reboots automatically after upgrading.
Figure 11-13 Remote Upgrade
11.8 Configuring RS-485
Purpose:
The RS-485 serial port is used to control the PTZ of the camera. The configuring of
the PTZ parameters should be done before you control the PTZ unit.
Steps:
1. Enter RS-485 Port Setting interface:
Configuration> Advanced Configuration> System > RS485
Figure 11-14 RS-485 Settings
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
2.
Set the RS-485 parameters and click
129
to save the settings.
The Baud Rate, PTZ Protocol and PTZ Address parameters of the positioning
system should be exactly the same as those of the control device.
11.9 Configuring Supplement Light
This function is only applicable to certain model of positioning systems.
Steps:
1. Enter Supplement Light Setting interface:
Configuration> Advanced Configuration> System > Service
2. Check the checkbox to enable the Supplement light when the illumination is not
enough for the video monitoring.
Figure 11-15 Setting Supplement Light
3. Click the
© Hikvision
button to activate the settings.
User Manual of Thermometric Bi-spectrum Network Positioning System
130
Appendix
Appendix 1 SADP Software Introduction
Description of SADP
SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free
online device search tool. It searches the active online devices within your subnet
and displays the information of the devices. You can also modify the basic network
information of the devices using this software.
Search active devices online
Search online devices automatically
After launch the SADP software, it automatically searches the online devices
every 15 seconds from the subnet where your computer locates. It displays
the total number and information of the searched devices in the Online
Devices interface. Device information including the device type, IP address
and port number, etc. will be displayed.
Figure A.1.1 Searching Online Devices
Device can be searched and displayed in the list in 15 seconds after it went online; it
will be removed from the list in 45 seconds after it went offline.
Search online devices manually
You can also click
to refresh the online device list manually. The
newly searched devices will be added to the list.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
You can click
you can click
or
131
on each column heading to order the information;
to expand the device table and hide the network parameter panel
on the right side, or click
to show the network parameter panel.
Modify network parameters
Steps:
1. Select the device to be modified in the device list and the network parameters of
the device will be displayed in the Modify Network Parameters panel on the
right side.
2. Edit the modifiable network parameters, e.g. IP address and port number.
3. Enter the password of the admin account of the device in the Password field and
click
to save the changes.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers and special characters) in
order to increase the security of your product.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
Figure A.1.2 Modify Network Parameters
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
132
Appendix 2 Port Mapping
The following settings are for TP-LINK router (TL-R410). The settings vary depending
on different models of routers.
Steps:
1. Select the WAN Connection Type, as shown below:
Figure A.2.1 Select the WAN Connection Type
2. Set the LAN parameters of the router as in the following figure, including IP
address and subnet mask settings.
Figure A.2.2 Set the LAN parameters
3. Set the port mapping in the virtual severs of Forwarding. You need to forward
ports 80, 8000, 8200~8210 and 554 for a positioning system.
You can change 80, 8000 and 554 ports value in the positioning system with web browser
or client software.
In the positioning system, the 8200~8210 ports change with the 8000 port with a
constant value of 200. E.g. if the 8000 port is changed to 8005, then the 8200~8210 ports
should be changed to 8205~8215.
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
133
Example:
When the positioning systems are connected to the same router, you can forward the
ports of a positioning system as 80, 8000, 8200~8210 and 554 with IP address
192.168.1.23, and the ports of another positioning system as 81, 8001, 8201~8211 and
555 with IP 192.168.1.24. Refer to the steps as below:
Steps:
1. As the settings mentioned above, forward the port 80, 8000, 8200~8210 and 554
for the network positioning system at 192.168.1.23
2. Forward the port 81, 8001, 8201~8211 and 555 for the network positioning
system at 192.168.1.24.
3. Enable ALL or TCP protocols.
4. Check the Enable checkbox and click
.
Figure A.2.3 Port Mapping
The port of the network positioning system cannot conflict with other ports.
For example, some web management port of the router is 80. Change the
positioning system port if it is the same as the management port.
© Hikvision
134
User Manual of Thermometric Bi-spectrum Network Positioning system
Appendix 3 RS485 Bus Connection
General Property of RS485 Bus
According to RS485 industry bus standard, RS485 is a half-duplex communication bus
which has 120Ω characteristic impendence, the maximum load ability is 32 payloads
(including controller device and controlled device).
RS485 Bus Transmission Distance
When using 0.56mm (24AWG) twisted-pair line, according to different baudrate, the
maximum transmission distance theory table is shown as below:
Max. Distance of RS485 Transmission
Baudrate
Max Distance
2400BPS
1800m
4800BPS
1200m
9600BPS
800m
The transmission distance will be decreased if we use the thinner cable, or use this
product under the strong electromagnetic interference situation, or there are lots of
devices are added to the bus; on the contrary, the transmission distance will be
increased.
Connection Methods
RS485 industry bus standard require daisy-chain connection method between any
devices, both sides have to connect a 120Ω terminal resistance (show as Diagram
1), the simplified connection method is shown as diagram 2, but the distance of
“D” should not be too long.
…
120Ω
2#
1#
120Ω
3#
32#
Figure A-7 RS485 Connection 1
A+
D
B-
Controller
A+
B-
1#
…
2#
31#
Figure A-8 RS485 Connection 2
Problems in the Practical Application
Normally, users adopt star-shape connection method in construction, under this
situation, the terminal resistors must be connected between two farthest devices (as
Figure A-9, 1# and 15#), but this connection method is not satisfy the requirement of
© Hikvision
135
User Manual of Thermometric Bi-spectrum Network Positioning system
the RS485 industry standard so that it will lead to some problems such as signal
reflection, anti-jamming ability decline when the devices are faraway. At this time,
the positioning system will be uncontrollable, or self-running, etc.
1#
6#
Controller
32#
15#
Figure A-9 Star Shape Connection
For such case, the best way is adding a RS485 distributor. This product can effectively
change the star-shape connection to which satisfies the requirement of RS485
industry standard, in order to avoid those problems and improve the communication
reliability. Refer to the following figure.
RS485 Distributor
A+
120
Ω
1#
120
Ω
2#
Ω
16#
B-
120
Figure A-10 RS485 Distributor
Troubleshooting of RS485 communication
Problem
Possible Reasons
To Solve the Problem
1. The address or baudrate of the 1. Adjust the address and
The
baudrate of the remote control
positioning positioning system does not
match with those of remote
device to match with those of the
system
control device.
positioning system.
does the
self-test
2. The wire RS485+ connects to
2. Connect the wire RS485+ to the
action but
the interface RS485- and wire
interface RS485+ and wire RS485cannot be
RS485- connects to the interface
to the interface RS485-.
controlled
RS485+.
remotely.
3. The RS485 wire is
3. Reconnect the RS485 wire
© Hikvision
User Manual of Thermometric Bi-spectrum Network Positioning system
Problem
The
positioning
system can
be
controlled
but not
smoothly.
Possible Reasons
disconnected.
4. RS485 wire is broken.
1. The connection is loose.
2. RS485+ or RS485-wire is
broken.
3. The positioning system is too
far away from the remote control
device.
4. Too many positioning systems
are connected.
© Hikvision
136
To Solve the Problem
tightly.
4. Change a RS485 wire.
1. Reconnect the RS485 wire
tightly.
2. Change a RS485 wire.
3. Add a terminal resistor.
4. Add a RS485 distributor.
137
User Manual of Thermometric Bi-spectrum Network Positioning system
Appendix 4 24VAC Wire Gauge & Transmission Distance
The following table describes the recommended max. distance adopted for the
certain wire gauge when the loss rate of 24VAC voltage is less than 10%. For the AC
driven device, the maximum voltage loss rate is 10% allowable. For example, for a
device with the rating powelr of 80VA which is installed at a distance of 35 feet (10m)
away from the transformer, then 0.8000mm is required as the minimum wire gauge.
Wire Gauge
(mm)
Distance
(feet)
0.8000
1.000
1.250
2.000
10
283(86)
451(137)
716(218)
1811(551)
20
141(42)
225(68)
358(109)
905(275)
30
94(28)
150(45)
238(72)
603(183)
40
70(21)
112(34)
179(54)
452(137)
50
56(17)
90(27)
143(43)
362(110)
60
47(14)
75(22)
119(36)
301(91)
70
40(12)
64(19)
102(31)
258(78)
80
35(10)
56(17)
89(27)
226(68)
90
31(9)
50(15)
79(24)
201(61)
100
28(8)
45(13)
71(21)
181(55)
110
25(7)
41(12)
65(19)
164(49)
120
23(7)
37(11)
59(17)
150(45)
130
21(6)
34(10)
55(16)
139(42)
140
20(6)
32(9)
51(15)
129(39)
150
18(5)
30(9)
47(14)
120(36)
160
17(5)
28(8)
44(13)
113(34)
170
16(4)
26(7)
42(12)
106(32)
180
15(4)
25(7)
39(11)
100(30)
190
14(4)
23(7)
37(11)
95(28)
200
14(4)
22(6)
35(10)
90(27)
Power (va)
© Hikvision
138
User Manual of Thermometric Bi-spectrum Network Positioning system
Appendix 5 Table of Wire Gauge Standards
Bare Wire
Gauge(mm)
0.750
0.800
0.900
1.000
1.250
1.500
2.000
2.500
3.000
© Hikvision
American
Wire Gauge
AWG
21
20
19
18
16
15
12
British Wire
Gauge SWG
21
20
19
18
17
14
Cross-sectional
Area of Bare
Wire(mm2)
0.4417
0.5027
0.6362
0.7854
1.2266
1.7663
3.1420
4.9080
7.0683
139
User Manual of Thermometric Bi-spectrum Network Positioning System
Appendix 6 Alarm In/Out Connections
This section is only for the positioning systems with alarm in/out functions.
The positioning system can be connected with alarm inputs (0~5VDC) and alarm
outputs. Refer to the following diagrams for alarm output:
GND OUT
DC Load
Dome
Relay Output
OUT( n)
+
DC -
OUT( n)
30VDC
1A
Dome
OUT( n)
JQC- 3FG
Relay
( 10 A 250VAC)
~220V AC
L
N
Relay Output
OUT( n)
Diagram (left)
Diagram(right)
Figure A-11 Alarm Out Connections
The alarm provides the relay output (no voltage), and the external power supply is
required when it connects to the alarm device.
For DC power supply (left diagram), the input voltage must be no more than
30VDC, 1A.
For AC power supply, the external relay must be used (right diagram) to prevent
damages to the positioning system and avoid risk of electric shock.
© Hikvision