Electric and Gas Models
Installation/Operation
Stacked Washer/Dryers
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
SWD455C_SVG
www.alliancelaundry.com
Part No. 805989R1
October 2015
WARNING
WARNING
•
Risk of fire. Highly flammable material.
W881
•
IMPORTANT: The electrical installation in the site shall
comply with the Australian Electrical Standards,
AS3000, SAA wiring rules, and such local regulations
that might apply. In Australia and New Zealand, installation must comply with the Gas Installations Standard
AS/NZS 5601 Part 1: General Installations.
The maximum washing load (dry weight) shall not exceed 9.5 kg
[21 pounds].
The maximum drying load (dry weight) shall not exceed 8.2 kg
[18 pounds].
•
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Clear the room, building or area of all occupants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
Read all instructions before using unit.
W052
IMPORTANT: Purchaser must consult the local gas
supplier for suggested instructions to be followed if
the dryer user smells gas. The gas utility instructions
plus the SAFETY and WARNING note directly above
must be posted in a prominent location near the dryer
for customer use.
WARNING
FOR YOUR SAFETY, the information in this manual
must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.
WARNING
W033
•
•
•
Installation of unit must be performed by a qualified installer.
Install clothes dryer according to manufacturer’s
instructions and local codes.
DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)
duct is installed, it must be of a specific type
identified by the appliance manufacturer as suitable for use with clothes dryers. Refer to section
on connecting exhaust system. Flexible venting
materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct
clothes dryer airflow and increase the risk of fire.
W729R1
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3
Part No. 805989R1
WARNING
To reduce the risk of severe injury or death, follow
all installation instructions. Save these instructions.
W894
WARNING
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
W053
This product uses FreeRTOS V7.2.0 (www.freertos.org).
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4
Part No. 805989R1
Table of Contents
Safety Information..................................................................................7
Explanation of Safety Messages....................................................................... 7
Important Safety Instructions........................................................................... 7
Important Safety Instructions........................................................................... 8
Dimensions........................................................................................... 10
Installation........................................................................................... 14
Before You Start...........................................................................................14
Tools........................................................................................................14
Order of Installation Steps..........................................................................14
Position Unit Near Installation Area............................................................... 14
Remove Shipping Materials........................................................................... 14
Connect Fill Hoses........................................................................................15
Water Supply Requirements....................................................................... 16
Connecting Hoses......................................................................................16
Risers....................................................................................................... 17
Non-Gravity Drain Models - Connect Drain Hose to Drain Receptacle.............. 18
Standpipe Installation................................................................................ 18
Gravity Drain Models - Connect Drain Outlet to Drain System......................... 18
Gas Dryers - Connect Gas Supply Pipe........................................................... 19
Connect Dryer Exhaust System...................................................................... 20
Exhaust Direction......................................................................................22
Exhaust System.........................................................................................22
Multi-Dryer Installation Exhaust Requirements............................................23
Position and Level the Unit............................................................................25
Wipe Out Inside of Washer and Dryer Drums..................................................26
Plug In the Washer........................................................................................27
Electrical Requirements............................................................................. 27
Earth/Ground Instructions.......................................................................... 28
Plug In the Dryer.......................................................................................... 28
Electrical Requirements............................................................................. 28
Earth/Ground Instructions.......................................................................... 30
Check Installation......................................................................................... 30
Check Heat Source........................................................................................30
Electric Dryers.......................................................................................... 30
Gas Dryers................................................................................................30
Operation............................................................................................. 32
Operation Instructions for Washers.................................................................32
Load Laundry........................................................................................... 32
© Copyright
2015, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5
Part No. 805989R1
Close Loading Door...................................................................................32
Add Laundry Supplies............................................................................... 32
Determine Proper Controls......................................................................... 33
Set Fabric Selector and Wash Temperature.................................................. 33
Insert Coins or Card...................................................................................33
Start Washer............................................................................................. 34
Indicator Lights.........................................................................................34
Operation Instructions for Dryers................................................................... 34
Clean Lint Filter........................................................................................ 35
Load Laundry........................................................................................... 35
Close Loading Door...................................................................................35
Determine Proper Controls......................................................................... 35
Set Fabric Selector.....................................................................................35
Insert Coins or Card...................................................................................35
Start Dryer................................................................................................36
Indicator Lights.........................................................................................36
Maintenance......................................................................................... 37
User-Maintenance Instructions....................................................................... 37
Lubrication............................................................................................... 37
Cold Weather Care.................................................................................... 37
Extended Non-Use.................................................................................... 37
Care of Your Washer................................................................................. 37
Care of Your Dryer....................................................................................38
Reinstallation of Shipping Materials............................................................... 38
Motor Overload Protector.............................................................................. 39
For Energy Conservation............................................................................... 39
Troubleshooting....................................................................................40
Contact Information............................................................................. 43
Installer Checklist.................................................................................44
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6
Part No. 805989R1
Safety Information
Safety Information
Explanation of Safety Messages
WARNING
Precautionary statements (“DANGER,” “WARNING,” and
“CAUTION”), followed by specific instructions, are found in this
manual and on machine decals. These precautions are intended
for the personal safety of the operator, user, servicer, and those
maintaining the machine.
To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer,
follow these basic precautions:
W023
DANGER
•
•
Indicates an imminently hazardous situation that, if
not avoided, will cause severe personal injury or
death.
WARNING
•
•
Indicates a hazardous situation that, if not avoided,
could cause severe personal injury or death.
CAUTION
•
Indicates a hazardous situation that, if not avoided,
may cause minor or moderate personal injury or
property damage.
Additional precautionary statements (“IMPORTANT” and
“NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor
machine damage will occur if the procedure is not followed.
•
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.
•
Important Safety Instructions
WASHER
Save These Instructions
•
•
•
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7
Read all instructions before using the washer.
Install the washer according to the INSTALLATION INSTRUCTIONS. Refer to the EARTH/GROUND INSTRUCTIONS in the INSTALLATION manual for the proper earth/
ground connection of the washer. All connections for water,
drain, electrical power and earth/ground must comply with local codes and be made by licensed personnel when required.
Do not do it yourself.
Do not install or store the washer where it will be exposed to
water and/or weather.
Do not add the following substances or textiles containing
traces of the following substances to the wash water: gasoline,
kerosene, waxes, cooking oils, vegetable oils, machine oils,
dry-cleaning solvents, flammable chemicals, thinners or other
flammable or explosive substances. These substances give off
vapors that could ignite, explode or cause the fabric to catch
on fire by itself.
Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using a
washing machine or combination washer-dryer, turn on all hot
water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. THE
GAS IS FLAMMABLE, DO NOT SMOKE OR USE AN
OPEN FLAME DURING THIS TIME.
To reduce the risk of an electric shock or fire, DO NOT use
an extension cord or an adapter to connect the washer to the
electrical power source.
Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used
near children. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their
safety. This is a safety rule for all appliances.
Cleaning and user maintenance shall not be made by children
without supervision.
Children less than three years should be kept away unless
continuously supervised.
Do not reach into the washer if the washtub or agitator, if applicable, is moving.
Part No. 805989R1
Safety Information
•
•
•
•
•
•
•
•
•
•
Never operate the washer with any guards, panels and/or parts
removed or broken. DO NOT tamper with the controls or bypass any safety devices.
Use your washer only for its intended purpose, washing
clothes. Always follow the fabric care instructions supplied
by the garment manufacturer.
Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times (preferably in a locked cabinet). Heed all
warnings or precautions.
Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener
or product.
Be sure water connections have a shut-off valve and that fill
hose connections are tight. CLOSE the shut-off valves at the
end of each wash day.
Keep your washer in good condition. Bumping or dropping
the washer can damage safety features. If this occurs, have
your washer checked by a qualified service person.
Do not repair or replace any part of the washer, or attempt any
servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions
that you understand and have the skills to carry out. ALWAYS disconnect the washer from electrical supply before
attempting any service.
Disconnect the power cord by grasping the plug, not the cord.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
Before the washer is removed from service or discarded, remove the lid or door to the washing compartment.
Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions
which can produce bodily injury and/or property damage.
WARNING
To reduce the risk of fire, electric shock, serious injury or death to persons when using your dryer, follow these basic precautions:
W130
•
•
•
•
•
•
NOTE: The WARNING and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the
washer.
•
•
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do not understand.
Important Safety Instructions
•
DRYER
•
Save These Instructions
•
•
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8
Read all instructions before using the dryer.
Install this dryer according to the INSTALLATION INSTRUCTIONS. Refer to the EARTH/GROUND INSTRUCTIONS in the INSTALLATION manual for the proper earth/
ground connection of the dryer. All connections for electrical
power, earth/ground and gas supply must comply with local
codes and be made by licensed personnel when required. Do
not do it yourself.
Do not install or store the dryer where it will be exposed to
water and/or weather.
Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline or machine
oils, vegetable or cooking oils, cleaning waxes or chemicals,
dry-cleaning solvents, thinner, anything containing chemicals
such as in mops and cleaning cloths, or other flammable or
explosive substances as they give off vapors that could ignite,
explode or cause fabric to catch on fire by itself.
Items that have been soiled with substances such as cooking
oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers, should be washed in hot water
with an extra amount of detergent before being dried in the
tumble dryer.
To reduce the risk of fire, DO NOT DRY plastics or articles
containing foam or latex rubber or similarly textured rubberlike materials, such as shower caps, water proof textiles, rubber-backed articles, and clothes or pillows filled with foam
rubber pads.
Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder
with a damp cloth to remove particles of fiberglass.
Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near
children. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning the use
of the appliance by a person responsible for their safety. This
is a safety rule for all appliances.
Cleaning and user maintenance shall not be made by children
without supervision.
Children less than three years should be kept away unless
continuously supervised.
Do not reach into the dryer if the cylinder is revolving.
Use the dryer only for its intended purpose, drying clothes.
ALWAYS follow the fabric care instructions supplied by the
Part No. 805989R1
Safety Information
•
•
•
•
•
•
•
•
•
•
garment manufacturer and only use the dryer drum to dry textiles that have been washed in water.
Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns,
keep them out of reach of children at all times (preferably in a
locked cabinet).
Remove laundry immediately after the dryer stops.
DO NOT operate the dryer if it is smoking, grinding or has
missing or broken parts or removed guards and/or panels. DO
NOT tamper with the controls or bypass any safety devices.
DO NOT operate individual units if they have been separated
from a stack unit.
Dryer will not operate with the loading door open. DO NOT
bypass the door safety switch by permitting the dryer to operate with the door open. The dryer will stop tumbling when the
door is opened. Do not use the dryer if it does not stop tumbling when the door is opened or starts tumbling without
pressing the START mechanism. Remove the dryer from use
and call the service person.
ALWAYS clean the lint filter after every load. A layer of lint
in the filter reduces drying efficiency and prolongs drying
time. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and
dirt. The interior of the dryer and the exhaust duct should be
cleaned periodically by qualified service personnel.
Do not repair or replace any part of the dryer, or attempt any
servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions
that you understand and have the skills to carry out. ALWAYS disconnect the electrical power to the dryer before attempting service. Disconnect the power cord by grasping the
plug, not the cord.
If supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Before the dryer is removed from service or discarded, remove the door to the drying compartment.
Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.
NOTE: The WARNING and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Observe and be aware of other labels and precautions that are located on the machine. They are intended to provide instruction for safe use of the machine. Common sense, caution and care must be exercised when installing, maintaining, or operating the
dryer.
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do not understand.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9
Part No. 805989R1
Dimensions
Dimensions
Electric Models Equipped With Drain Hose
C
G
F
D
E
A
L
B
M
H
J
Q
P
O
K
N
I
SWD1023N_SVG
A
* 1678 mm [66.06 in.]
B
* 1447 mm [56.97 in.]
C
597 mm [23.5 in.]
D
213 mm [8.375 in.]
E
610 mm [24 in.]
F
203 mm [8 in.]
G
391 mm [15.4 in.]
H
* 938 mm [36.9 in.]
I
* 368 mm [14.5 in.]
J
* 813 mm [32 in.]
K
683 mm [26.875 in.]
L
* 1986 mm [78.17 in.]
M
* 1184 mm [46.62 in.]
N
52 mm [2.04 in.]
O
704 mm [27.73 in.]
P
38 mm [1.5 in.]
Q
* 333 mm [13.1 in.]
NOTE: Exhaust openings are 102 mm [4 inch] metal
ducting.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
* With leveling legs turned into base.
10
Part No. 805989R1
Dimensions
Gas Models Equipped With Drain Hose
C
G
F
D
H
1
E
A
O
B
I
N
K
L
S
R
Q
M
P
J
SWD1024N_SVG
1. 3/8 in. NPT Gas Connection
A
*1678 mm [66.06 in.]
B
*1447 mm [56.97 in.]
C
597 mm [23.5 in.]
D
213 mm [8.375 in.]
E
610 mm [24 in.]
F
203 mm [8 in.]
G
391 mm [15.4 in.]
H
59 mm [2.3 in.]
I
*938 mm [36.9 in.]
J
*368 mm [14.5 in.]
K
*1140 mm [44.87 in.]
L
*813 mm [32 in.]
M
683 mm [26.875 in.]
N
*1986 mm [78.17 in.]
O
*1184 mm [46.62 in.]
P
52 mm [2.04 in.]
Q
704 mm [27.73 in.]
R
38 mm [1.5 in.]
S
*333 mm [13.1 in.]
NOTE: Exhaust openings are 102 mm [4 inch] metal
ducting.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
* With leveling legs turned into base.
11
Part No. 805989R1
Dimensions
Gas Models Equipped With Gravity Drain
C
G
F
D
A
H
1
E
B
Q
I
K
P
L
O
U
T
N
S
R
M
2
J
SWD1028N_SVG
1. 3/8 in. NPT Gas Connection
2. 38 mm [1.5 in.] Inside Diameter; 47 mm [1.86 in.] Outside Diameter
A
*1678 mm [66.06 in.]
B
*1447 mm [56.97 in.]
C
597 mm [23.5 in.]
D
213 mm [8.375 in.]
E
610 mm [24 in.]
F
203 mm [8 in.]
G
391 mm [15.4 in.]
H
60 mm [2.3 in.]
I
*938 mm [36.9 in.]
J
*368 mm [14.5 in.]
K
*1140 mm [44.87 in.]
L
*813 mm [32 in.]
M
683 mm [26.875 in.]
N
107 mm [4.2 in.]
O
*104 mm [4.1 in.]
P
*1184 mm [46.62 in.]
Q
*1986 mm [78.17 in.]
R
52 mm [2.04 in.]
S
704 mm [27.73 in.]
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12
Part No. 805989R1
Dimensions
T
38 mm [1.5 in.]
U
*333 mm [13.1 in.]
NOTE: Exhaust openings are 102 mm [4 inch] metal
ducting.
* With leveling legs turned into base.
NOTE: Gas models cannot be vented out left side of
cabinet because of burner housing.
IMPORTANT: The dryer should have sufficient clearance around it for needed ventilation and for the ease
of installation and servicing. For maximum drying performance, we recommend that more clearance be allowed around the dryer than the clearances that are listed throughout this manual.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13
Part No. 805989R1
Installation
Installation
Before You Start
WARNING
Tools
Any disassembly requiring the use of tools must be
performed by a suitably qualified service person.
For most installations, the basic tools you will need are:
1
2 3
4
W299
5
Order of Installation Steps
6
11
7
9
10
8
SWD1021N_SVG
1. Wrench
2. 1/4 inch Driver
3. Screwdriver
4. Level
5. Wood Block
6. Pliers
7. 5/16 Inch Socket Wrench
8. Gloves
9. Teflon Tape (Gas Models)
10. Duct Tape
11. Safety Glasses
The proper order of steps must be followed to ensure correct installation. Refer to the list below when installing your unit.
1.
2.
3.
4.
Position unit near area of installation.
Remove the shipping materials.
Connect the fill hoses.
For gas models only, connect the gas supply pipe. Check for
gas leaks.
5. Connect dryer to exhaust system.
6. Position and level the unit.
7. Wipe out inside of washer and dryer drums.
8. Connect the washer and dryer to electrical power.
9. Recheck steps.
10. Start and run the dryer in a heat setting to verify dryer is heating.
Position Unit Near Installation Area
Move unit so that it is within 1.2 meters [4 feet] of the desired
area of installation.
CAUTION
Washer and dryer are not designed to be operated as
separated, side-by-side units.
Figure 1
NOTE: An 20.32 cm [8 in.] coin drawer is required for
coin operated models.
NOTE: If the unit is delivered on a cold day (below
freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate it until
the unit has had a chance to warm up.
NOTE: Some moisture in the wash drum is normal. Water is used during testing at the manufacturer.
NOTE: This appliance is suitable for use in countries
having a warm, damp climate.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
W187
NOTE: For best performance and to minimize vibration
or movement, install washer on a solid, sturdy and level floor. Some floors may need to be reinforced, especially on a second floor or over a basement. Do not install the washer on carpeting, soft tile or other weakly
supported structures.
Remove Shipping Materials
1. Remove two screws at bottom of front access panel. Rotate
bottom of panel out and remove panel.
14
Part No. 805989R1
Installation
FLW2297N_SVG1
Figure 4
FLW2378N_SVG
Figure 2
6. Insert two plugs included in accessories bag into rear shipping
bolt holes.
2. Remove two 9/16 inch bolts and washers holding shipping
brace to weight.
3. Remove two 9/16 inch bolts and washers holding shipping
brace to washer base and remove brace.
FLW2358N_SVG
Figure 5
7. Replace front access panel.
8. Save all shipping materials. They must be reinstalled any time
washer is moved more than four feet.
IMPORTANT: Do not lift or transport unit from front
or without shipping materials installed. Refer to the
Maintenace section for proper instructions on reinstalling the shipping materials.
FLW2296N_SVG1
Figure 3
Connect Fill Hoses
4. Go to rear of washer and pull label from rear shipping bolts.
5. Remove two 9/16 inch bolts. Unscrew each bolt while applying forward pressure just until bolt stops unthreading. Work
each bolt and spacer out by hand using a circular motion.
WARNING
NOTE: Avoid backing bolts out completely or
spacers might fall into cabinet.
Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used
for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for
such a period and before using the washer, turn on
all hot water faucets and let the water flow from each
for several minutes. This will release any accumulated hydrogen gas. The gas is flammable. Do not
smoke or use an open flame during this time.
W029
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
15
Part No. 805989R1
Installation
Water Supply Requirements
Water supply faucets must fit standard 19 mm [3/4 inch] female
garden hose couplings. DO NOT USE SLIP-ON OR CLAMPON CONNECTIONS.
NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being
used.
Recommended cold water temperature is 10° to 24° Celsius [50°
to 75° Fahrenheit]. Recommended maximum hot water temperature is 51° Celsius [125° Fahrenheit]. Warm water is a mixture of
hot and cold water. Warm water temperature is dependent upon
the water temperature and the pressure of both the hot and cold
water supply lines.
WARNING
To prevent personal injury, avoid contact with inlet
water temperatures higher than 51° Celsius [125°
Fahrenheit] and hot surfaces.
W748
Maximum flow rate for all water temperatures is 9.46 liters per
minute [2.5 gallons per minute] ± 15%.
Water pressure must be a minimum of 138 to a maximum of 827
kPa [minimum of 20 to a maximum of 120 pounds per square
inch] static pressure measured at the faucet.
NOTE: Water pressure under 138 kPa [20 pounds per
square inch] will cause an extended fill time in the
washer and may not properly flush out the detergent
dispenser.
The appliance is to be connected to the water mains using new
hose-sets and the old hose-sets should not be reused.
Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could
clog the screens in the water mixing valve. This is especially important when installing your washer in a newly constructed or
renovated building. Build-up may have occurred during construction.
Figure 6
Connections should be supplied by a hot and a cold water line per
national and local codes and in accordance with AS/NZS 3500.1.
1. Insert rubber washers and filter screens (from accessories
bag) in water fill hose couplings (two hoses supplied with
washer). The filter screen must be facing outward.
NOTE: If using hoses with BSPP thread coupling, insert filter screens into the BLACK colored hose couplings and the rubber washers into the brass colored hose couplings.
2. Connect fill hose couplings with filter screens to water supply
faucets.
3. Connect the other hose couplings to the hot and cold valve
connections at the rear of the washer.
NOTE: If using hoses with BSPP thread coupling,
connect the BLACK colored hose coupling end of
the fill hoses (with filter screens) to the water supply
faucets. Then connect end of hoses with the brass
colored hose couplings to the hot and cold water
mixing valve connections at rear of washer.
4. Thread hose couplings onto valve connections finger tight.
Then turn 1/4 turn with pliers.
IMPORTANT: DO NOT cross thread or overtighten
couplings. This will cause them to leak.
5. Turn water on and check for leaks.
6. If leaks are found, retighten the hose couplings.
7. Continue tightening and rechecking until no leaks are found.
Connecting Hoses
To comply with Australian water regulations and Australian
standard AS/NZS3500.1, an approved dual check valve backflow
prevention device with the watermark is provided with the unit
and must be fitted at the point of connection(s) between the supply and the fitting. Refer to Figure 7 .
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16
Part No. 805989R1
Installation
1
COLD
HOT
1
2
7
2
3
4
3
6
4
5
SWD1025N_SVG
5
1.
2.
3.
4.
5.
FLW2216N_SVG
1. Faucet
2. Fill Hoses
3. Install this end of hose to valve connections at rear of
washer
4. Plain Rubber Washer
5. Install this end of hose to water supply faucet (Black colored coupling for BSPP thread)
6. Filter Screens
7. Dual Check Valves
Figure 7
IMPORTANT:
Hoses and other natural rubber parts deteriorate after extended
use. Hoses may develop cracks, blisters or material wear from the
temperature and constant high pressure they are subjected to.
All hoses should be checked on a monthly basis for any visible
signs of deterioration. Any hose showing the signs of deterioration listed above should be replaced immediately. All hoses
should be replaced every five years.
Water Supply Faucets
Cold Water Connection
Water Mixing Valve
Hot Water Connection
Fill Hoses
Figure 8
IMPORTANT: Turn off water supply faucets after checkout and demonstration. Owner should turn off water
supply whenever there will be an extended period of
non-use.
NOTE: Longer fill hoses are available (as optional
equipment at extra cost) if the hoses (supplied with the
washer) are not long enough for the installation. Order
hoses as follows:
•
•
•
•
No. 20617 Fill Hose: 2.44 m [8 feet] (2 standard thread hose
couplings)
No. 20618 Fill Hose: 3.05 m [10 feet] (2 standard thread hose
couplings)
No. 37380 Fill Hose: 2.44 m [8 feet] (1 standard thread, 1
BSPP thread hose coupling)
No. 37381 Fill Hose: 3.05 m [10 feet] (1 standard thread, 1
BSPP thread hose coupling)
Risers
Risers (or air cushions) may have to be installed if the pipes
knock or pound when flow of water stops. The risers are more efficient when installed as close as possible to the water supply faucets. Refer to Figure 9 .
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
17
Part No. 805989R1
Installation
the drain hose from dislodging from drain receptacle during
use.
1
1
2
W005I_SVG
1. Risers (Air cushions)
2. Water Supply Faucets
2
3
Figure 9
SWD1026N_SVG
1. 610 to 914 mm [24 to 36 in.] Recommended Height
2. Beaded strap from accessory bag
3. Standpipe 51 mm [2 in.] or 40 mm [1-1/2 in.]
Non-Gravity Drain Models - Connect
Drain Hose to Drain Receptacle
Remove the drain hose from its shipping position on the rear of
the washer by removing the shipping tape.
IMPORTANT: Drain receptacle must be capable of handling a minimum of 35 mm [1-3/8 inch] outside diameter drain hose.
Drain Flow Rate
Flow Rate
Drain Height
liters per minute [gallons per minute]
0.9 m [3 ft.]
27.7 [7.3]
1.5 m [5 ft.]
17.8 [4.7]
1.8 m [6 ft.]
13.4 [3.5]
2.1 m [7 ft.]
4.8 [1.3]
2.4 m [8 ft.]
0 [0]
Figure 10
Gravity Drain Models - Connect Drain
Outlet to Drain System
1. Remove drain fitting (102 mm [4 inches] long) and hose
clamp from accessories bag. Insert drain fitting into drain outlet hose. Clamp hose and fitting.
2. Connect the drain fitting to a vented drain system using a
flexible connection (obtain locally). Inside diameter of fitting
is 39 mm [1.53 in.] and outside diameter is 42 mm [1.66 in.].
3. The drain system must be vented to prevent an air lock or siphoning.
IMPORTANT: Increasing the drain hose length, installing elbows, or causing bends will decrease
drain flow rates and increase drain times, impairing
machine performance.
Standpipe Installation
1. Place the drain hose into the standpipe.
2. Remove the beaded tie-down strap from accessories bag and
place around standpipe and drain hose and tighten strap to
hold hose to standpipe. Refer to Figure 10 . This will prevent
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18
Part No. 805989R1
Installation
NOTE: Natural gas, 37.3 MJ/m3 [1000 Btu/ft3], service must be supplied at 1.13 kPa [4.54 inch]water
column pressure. Do not connect the dryer to L.P.
(Liquefied Petroleum) gas service without converting the gas valve. A No. 458P3 L.P. Gas Conversion
Kit must be installed by the Manufacturer’s Authorized Dealers, Distributors, or local service personnel.
NOTE: L.P. gas, 93.1 MJ/m3 [2500 Btu/ft3], service
must be supplied at 2.75 kPa [11.04 inch] water column pressure and a vent to the outdoors must be
provided.
4. If local codes allow the use of flexible gas tubing, connect the
9.5 mm [3/8 inch] NPT (National Pipe Thread) gas connection at the rear of the dryer to the laundry room’s gas line with
new flexible stainless steel tubing (using design certified Australian Gas Association connector only).
IMPORTANT: Use local codes of practice for gas installation.
This dryer is equipped with jet for Natural gas.
2
Gas Consumption
Natural
27.4 MJ
L.P.
27.4 MJ
Gas Supply Pres- Natural
sure
L.P.
1
1.13 kPa
2.75 kPa
WARNING
SWD1002N_SVG
1. Drain Trough
2. Drain Outlet Hose
To reduce the risk of gas leaks, fire or explosion:
•
Figure 11
Gas Dryers - Connect Gas Supply Pipe
•
•
NOTE: The gas service to a gas dryer must conform
with the local codes and ordinances and in Australia
and New Zealand, installation must comply with the
Gas Installations Standard AS/ NZS 5601 Part 1: General Installations. In the absence of local codes and ordinances, applicable National codes should be followed.
1. Install the dryer with sufficient clearance for adequate air circulation, and for the ease of the dryer installation, servicing
and operation. For maximum drying performance, we recommend you allow more clearance than the clearances that are
listed throughout this manual.
2. Remove the shipping cap from the gas connection at the rear
of the dryer. Make sure you do not damage the pipe threads
when removing the cap.
3. Make certain your dryer is equipped for use with the type of
gas in your laundry room.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
•
•
•
The dryer must be connected to the type of
gas as shown on nameplate located in the
door recess.
Use a new flexible stainless steel connector.
Use pipe joint compound insoluble in L.P. (Liquefied Petroleum) Gas, or Teflon tape, on all
pipe threads.
Purge air and sediment from gas supply line
before connecting it to the dryer. Before tightening the connection, purge remaining air from
gas line to dryer until odor of gas is detected.
This step is required to prevent gas valve contamination.
Do not use an open flame to check for gas
leaks. Use a non-corrosive leak detection fluid.
Any disassembly requiring the use of tools
must be performed by a suitably qualified service person.
W316
19
Part No. 805989R1
Installation
Natural Gas Altitude Adjustments
1
Altitude
Orifice Size
4
m [feet]
2
3
D246I_SVG
1. New Stainless Steel Flexible Connector – Use Only If Allowed By Local Codes (Use design AGA certified connector)
2. Pressure Test Point
3. External Shut-Off Valve
4. 3/8 in. NPT Gas Connection
NOTE: The dryer and its individual gas valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test
pressures in excess of 3.45 kPa [1/2 psig].
6. Check all pipe connections (internal and external) for gas
leaks with a soapy solution. Gas connections should be
checked annually for leakage.
7. Be sure the shut off valve in your dryer is OPEN. Your dryer
is shipped with the valve open.
8. The dryer gas valve is equipped with a pressure test point for
checking manifold pressure.
610 [2,000]
41
2.44 [0.0960]
503776
915 [3,000]
42
2.37 [0.0935]
503777
1,680 [5,500]
43
2.26 [0.0890]
503778
2,135 [7,000]
44
2.18 [0.0860]
58719
2,745 [9,000]
45
2.08 [0.0820]
503779
3,200
[10,500]
46
2.06 [0.0810]
503780
Table 1
L.P. Altitude Adjustments
Altitude
Figure 12
NOTE: When connecting gas supply line, a pressure
test point must be installed downstream from the
shutoff valve for checking inlet gas pressure.
5. The gas line to your laundry room should be made of black
iron pipe. A 9.5 mm [3/8 inch] pipe with an inside diameter of
11.7 mm [0.46 inch] will be adequate if length of supply line
is not over 6 m [20 feet]. If length exceeds this, use 12.7 mm
[1/2 inch] pipe. If copper semi-rigid tubing is used it must be
internally tinned or equivalently treated to resist sulfur corrosion.
Part Number
mm [inches]
No.
Orifice Size
m [feet]
mm [inches]
No.
Part No.
1070 [3500]
54
1.40 [0.0550]
503785
2290 [7500]
55
1.32 [0.0520]
58755
3355 [11000]
56
1.18 [0.0465]
503786
Table 2
Connect Dryer Exhaust System
WARNING
To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors.
W604
For proper operation at altitudes above 610 m [2000 feet] the natural gas valve spud orifice size must be reduced to ensure complete combustion. Refer to Table 1 and Table 2 .
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
20
Part No. 805989R1
Installation
WARNING
To reduce the risk of fire and the accumulation of
combustion gases, DO NOT exhaust dryer air into a
window well, gas vent, chimney or enclosed, unventilated area, such as an attic, wall, ceiling, crawl
space under a building or concealed space of a
building.
W045
WARNING
To reduce the risk of fire, DO NOT use plastic or thin
foil ducting to exhaust the dryer.
1
SWD997N_SVG
W354
1. Correct
2. Incorrect
WARNING
Figure 13
To reduce the risk of fire, the exhaust duct and
weather hood MUST be fabricated of a material that
will not support combustion. Rigid or flexible metal
pipe is recommended for a clothes dryer.
•
•
•
W048
•
•
WARNING
To reduce the risk of fire due to increased static
pressure, we do not recommend installation of inline secondary lint filters or lint collectors. If secondary systems are mandated, frequently clean the
system to assure safe operation.
W749
IMPORTANT: Installing in-line filters or lint collectors
will cause increased static pressure. Failure to maintain the secondary lint system will decrease dryer efficiency and will void machine warranty.
•
•
•
•
•
•
•
•
•
•
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
2
21
DO NOT use plastic, thin foil or type B ducting. Rigid metal
duct is recommended.
Locate dryer so exhaust duct is as short as possible.
Be certain old exhaust ducts are cleaned before installing your
new dryer.
Use 102 mm [4 inch] diameter rigid or flexible metal duct.
The male end of each section of duct must point away from
the dryer.
Use as few elbows as possible.
Use of duct tape or pop-rivets on all seams and joints is recommended, if allowed by local codes. DO NOT use sheet
metal screws or fasteners on exhaust pipe joints which extend
into the duct and catch lint.
Ductwork that runs through unheated areas must be insulated
to help reduce condensation and lint build-up on pipe walls.
Install backdraft dampers in multi-dryer installations.
In mobile home installations, dryer exhaust duct must be secured to mobile home structure.
Dryer exhaust duct MUST NOT terminate under mobile
home.
Exhaust duct must not be connected to any other duct, vent, or
chimney.
Dryer exhausts 5.09 cmm (180 cfm) per unit (measured at
back of dryer).
DO NOT install flexible duct in concealed spaces, such as a
wall or ceiling.
Static pressure in exhaust duct should not be greater than 10
mm water column [0.4 inches water column], measured with
manometer placed on exhaust duct 610 mm [two feet] from
dryer (check with dryer running and no load). In multi-dryer
Part No. 805989R1
Installation
installations, all dryers connected to the main collector duct
should be operating when pressure is checked.
Exhausting dryer in hard-to-reach locations can be done by
installing 521P3 Flexible Metal Vent Kit (available as optional equipment at extra cost).
Sufficient make-up air must be supplied to replace the air exhausted by the dryer. The free area of any opening for outside
air must be at least 1016 mm2 [40 in.2] per unit.
Energy efficient buildings with low air infiltration rates
should be equipped with an air exchanger that can accommodate on demand make-up air needs in the laundry room. These
devices can be obtained through your building contractor or
building material suppliers.
Do not draw make-up air from a room containing a gas fired
water heater, a dry cleaner or a hair salon.
Failure to exhaust dryer properly will void warranty.
A dryer will dissipate 681,392 J/m2 [60 Btu/ft2] of surface
area exposed to the conditioned air.
•
•
•
•
•
•
Dryer is shipped from factory ready for rear exhaust.
Exhausting the dryer through sides or bottom can be accomplished by installing a Directional Exhaust Kit, 528P3, available as
optional equipment at extra cost.
IMPORTANT: DO NOT block the airflow at the bottom
of the dryer’s front panel with laundry, rugs, etc. Blockage will decrease airflow through the dryer, thus reducing the efficiency of the dryer.
Exhaust System
For best drying results, recommended maximum length of exhaust system is shown in Table 3 .
To prevent backdraft when dryer is not in operation, outer end of
exhaust pipe must have a weather hood with hinged dampers (obtain locally).
NOTE: Weather hood should be installed at least 305
mm [12 inches] above the ground. Larger clearances
may be necessary for installations where heavy snowfall can occur.
NOTE: Venting materials are not supplied with the dryer (obtain locally).
IMPORTANT: DO NOT block the airflow at the bottom
of the dryer’s front panel with laundry, rugs, etc. Blockage will decrease airflow through the dryer, thus reducing the efficiency of the dryer.
Exhaust Direction
The dryer can be exhausted to the outdoors through the back, left,
right or bottom of the dryer. EXCEPTION: Gas dryers cannot be
vented out the left side because of the burner housing.
Weather Hood Type
Number of 90° Elbows
Recommended
1
Use Only for Short Run Installations
1
D673I_SVG
1
1. 102 mm [4 in.]
D802I_SVG
1. 64 mm [2.5 in.]
Maximum length of 102 mm [4 in.] diameter rigid metal duct.
0
19.8 m [65 feet]
16.8 m [55 feet]
1
16.8 m [55 feet]
14.3 m [47 feet]
2
14.3 m [47 feet]
12.5 m [41 feet]
Table 3 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
22
Part No. 805989R1
Installation
Weather Hood Type
Number of 90° Elbows
Recommended
Use Only for Short Run Installations
3
11.0 m [36 feet]
9.1 m [30 feet]
4
8.5 m [28 feet]
6.7 m [22 feet]
Table 3
NOTE: Deduct 1.8 m [6 feet] for each additional elbow.
Multi-Dryer Installation Exhaust Requirements
NOTE: The maximum length of a 102 mm [4 in.] diameter flexible metal duct must not exceed 2.4 m [7.87 ft.],
as required to meet UL2158, clause 7.3.2.A.
Figure 14 shows a typical example of a multiple dryer installation. Note how each dryer has its own exhaust system vented to
the central exhaust duct.
2
1
4
3
SWD998N_SVG
1.
2.
3.
4.
58786 Backdraft Damper (Available through your local authorized parts source)
Clean Out Cover (Must be provided). Inspect monthly.
Weather Hood or Sweep Elbow (No cap or screen)
610 mm [24 in.] Minimum Clearance to Roof/Ground
Figure 14
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
23
Part No. 805989R1
Installation
Horizontal Exhaust Installation: Exhaust Air Flow Maximum Length of Duct 9.1 m [30 feet]
1
2
9
A
B
C
D
E
F
G
H
I
J
K
3
7
4
8
6
5
D686I_SVG
1.
2.
3.
4.
5.
6.
7.
8.
9.
Where the exhaust duct pierces a combustible wall or ceiling, the opening must be sized per local codes.
Wall
50 mm [2 in.] Minimum or Clearance per Local Codes
No Screen or Cap
610 mm [24 in.] Minimum Clearance to Roof/Ground
Exhaust Outlet
Air Flow
30 °
Clean Out Cover - Inspect Monthly
Figure 15
Minimum Diameter of
Collector Duct
Duct Station
A
102 mm [4 inches]
B
203 mm [8 inches]
C
229 mm [9 inches]
D
254 mm [10 inches]
E
279 mm [11 inches]
F
305 mm [12 inches]
G
326 mm [13 inches]
H
356 mm [14 inches]
I
381 mm [15 inches]
J
381 mm [15 inches]
K
406 mm [16 inches]
Table 4
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
24
Part No. 805989R1
Installation
Vertical Exhaust Installation
WARNING
3
Units elevated above floor level must be anchored to
that elevated surface, base or platform. The material
used to elevate the unit should also be anchored to
the floor to ensure that the unit will not walk or that
the unit can not be physically pulled, tipped or slid
from its installed position. Failure to do so may result in conditions which can produce serious injury,
death and/or property damage.
4
2
1
7
W307
1. Position unit so it has sufficient clearance for installation and
servicing.
5
6
D753I_SVG
C
1.
2.
3.
4.
5.
6.
Roof
610 mm [24 in.] Minimum Clearance to Roof/Ground
No Screen or Cap
Wall
50 mm [2 in.] Minimum
Where the exhaust duct pierces a combustible wall or ceiling, an opening must be sized as shown or per local codes.
7. Connect to Dryer
D
E
E
Figure 16
WARNING
A
To reduce the risk of fire and the accumulation of
combustion gases, DO NOT exhaust dryer air into a
window well, gas vent, chimney or enclosed, unventilated area, such as an attic, wall, ceiling, crawl
space under a building or concealed space of a
building.
B
SWD1006N_SVG
NOTE: Shaded areas indicate adjacent structure.
Dryer and Exhaust Duct Clearances
W045
Area
A Backdraft Damper, Part No. 58786 (obtain locally),should be
installed in a 102 mm [4 inch] diameter VERTICAL duct system.
This will prevent a backdraft when dryer is not in use, and will
keep the exhaust air in balance within the central exhaust system.
Position and Level the Unit
Description
Minimum
Clearance
A
Left Dryer Side
0 mm [0 in.]
B
Right Dryer Side
25 mm [1 in.]
C
Dryer Top
152 mm [6 in.]
D*
Dryer Rear
102 mm [4 in.]
E
Exhaust Duct
51 mm [2 in.]
Clearance to
Combustible Materials
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
25
Part No. 805989R1
Installation
Dryer and Exhaust Duct Clearances
Area
Description
1
Minimum
Clearance
* Rear clearance is minimum. 152 mm [6 inches] are
recommended when venting through rear of unit.
2.
3.
4.
5.
6.
NOTE: Use of the dispenser drawer or unit doors as
a handle in the transportation of the unit may cause
damage to the dispenser or doors.
Place unit in position on a solid, sturdy and level floor. Installing the unit on any type of carpeting, soft tile or other weakly
supported structures is not recommended.
The unit must not be installed behind a lockable door, a sliding door, or a door with a hinge on the opposite side of the
unit.
Place a level on the raised portion of cabinet top and check if
the unit is level from side to side and front to back.
If unit is not level, tilt unit to access the front and rear leveling legs. For easier access to leveling legs, prop up unit with a
wooden block.
Loosen 7/8 in. locknut and adjust legs by screwing into or out
of unit base until the unit is level from side to side and front
to back (using a level). Unit should not rock.
NOTE: Leveling legs can also be adjusted from inside the unit using an adjustable wrench.
7. Tighten the locknuts securely against the unit base. If the
locknuts are not tight, unit will move out of position during
operation.
NOTE: DO NOT slide unit across floor if the leveling
legs have been extended. Legs and base could become damaged.
8. Remove rubber feet from accessories bag and place on all
four leveling legs.
9. Verify that unit doesn’t rock.
6
5
2
4
3
SWD1029N_SVG
1.
2.
3.
4.
5.
6.
Level
Wood Block
Rubber Foot
Leveling Leg
Locknut
Unit Base
Figure 17
Wipe Out Inside of Washer and Dryer
Drums
IMPORTANT: Prior to first wash, use an all-purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside the drums.
SWD1012N_SVG
Figure 18
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
26
Part No. 805989R1
Installation
CAUTION
If this appliance is supplied from a cord extension
set or an electrical portable outlet device, the cord
extension set or electrical portable outlet device
must be positioned so that it is not subject to
splashing or ingress of moisture.
W563
WARNING
To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to connect
the washer to the electric power source.
SWD1013N_SVG
W082
Figure 19
The washer is designed to be operated on a separate polarized
three-wire, earth/ground, 240 Volt, 50 Hertz, single-phase electrical circuit protected by a 10 ampere fuse, equivalent fusetron or
circuit breaker.
Plug In the Washer
Electrical Requirements
240 Volt/50 Hertz with 3-Prong Earth/Ground Plug
This appliance is to be supplied through a residual current device
(RCD) having a rated residual operating current not exceeding 30
mA.
The 3-prong earth/ground plug on the power cord should be plugged directly into a polarized three-slot receptacle properly installed and connected to a protective earth/ground and rated 240
Volts AC (alternating current) 10 Amps. Refer to Figure 20 to
determine correct polarity of the wall receptacle.
NOTE: The wiring diagram is located in the control cabinet.
WARNING
To reduce the risk of fire, electric shock, serious injury or death, all wiring and earth/ground connections MUST conform with the latest edition of the
AS/NZS 2040.2:2005 and such local regulations as
might apply. It is the customer’s responsibility to
have the wiring, fuses and circuit breakers installed
by a qualified electrician to make sure adequate electrical power is available to the washer.
W895
When plugging in the washer:
•
•
•
•
DO NOT overload circuits.
DO NOT use an extension cord.
DO NOT use an adapter.
DO NOT operate both a washer and a gas dryer on the same
circuit.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
27
Part No. 805989R1
Installation
Standard 240 Volt, 50 Hertz, 3 Wire Effective Earth/
Ground Circuit
•
3
room has an effective earth/ground, have a qualified electrician or your local electrical utility company check it and correct any problems.
Do not operate other appliances on the same circuit when this
appliance is operating.
WARNING
3
4
Any disassembly requiring the use of tools must be
performed by a suitably qualified service person.
W299
WARNING
This unit is equipped with a three-prong (earth/
ground) plug for your protection against shock hazard and should be plugged directly into a protective
earth/ ground three-prong receptacle. Do not cut or
remove the earth/ground prong from this plug.
2
1
1.
2.
3.
4.
TLW2166N_SVG
Power Cord
Earth/Ground Prong
240 Volt/50 Hertz
0 Volt
W823
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order
to avoid a hazard.
Figure 20
Earth/Ground Instructions
This appliance must be properly connected to protective earth/
ground. In the event of malfunction or breakdown, the earth/
ground will reduce the risk of electric shock by providing a path
of least resistance for electric current.
The appliance is equipped with a cord having an equipment earth/
ground conductor and a three-prong earth/ground plug. The plug
must be plugged into an appropriate outlet that is properly installed and connected to a protective earth/ground in accordance with
all local codes and ordinances.
Plug In the Dryer
This appliance is to be supplied through a residual current device
(RCD) having a rated residual operating current not exceeding 30
mA.
Electrical Requirements
Electric Dryer
NOTE: The wiring diagram is located in the control cabinet.
WARNING
WARNING
Improper connection of the equipment earth/ground
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if
you are in doubt as to whether the unit is properly
connected to a protective earth/ground.
To reduce the risk of fire, electric shock or personal
injury, all wiring and earthing to the dryer MUST conform with the latest edition of the Australian Electrical Standards, AS3000, SAA wiring rules, and such
local regulations that might apply.
W893
W478
•
•
DO NOT modify the plug provided with the unit – if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
If the laundry room’s electrical supply does not meet the
above specifications and/or if you are not sure the laundry
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
This dryer is designed to be operated on a two-wire, plus earth/
ground, 240 Volt, 50 Hertz, single-phase circuit, fused at 20 Amperes.
28
Part No. 805989R1
Installation
Insert the dryer’s lead-in cord plug into an earthing three-slotplus earth/ground, wall receptacle on a separate circuit. Do not
operate other appliances on the same circuit.
WARNING
To reduce the risk of fire, electric shock or personal
injury, all wiring and earthing to the dryer MUST conform with the latest edition of the Australian Electrical Standards, AS3000, SAA wiring rules, and such
local regulations that might apply.
CAUTION
If this appliance is supplied from a cord extension
set or an electrical portable outlet device, the cord
extension set or electrical portable outlet device
must be positioned so that it is not subject to
splashing or ingress of moisture.
W563
If the supply cord is damaged, it must be replaced by the manufacturer, its special agent or similarly qualified persons in order
to avoid a hazard.
W478
This dryer is designed to be operated on a two-wire, plus earth/
ground, 240 Volt, 50 Hertz, single-phase circuit, fused at 10 Amperes.
Insert the dryer’s lead-in cord plug into an earthing three-slotplus earth/ground, wall receptacle on a separate circuit. Do not
operate other appliances on the same circuit.
CAUTION
If this appliance is supplied from a cord extension
set or an electrical portable outlet device, the cord
extension set or electrical portable outlet device
must be positioned so that it is not subject to
splashing or ingress of moisture.
1
2
W563
3
A
25
If the supply cord is damaged, it must be replaced by the manufacturer, its special agent or similarly qualified persons in order
to avoid a hazard.
20
0V
IMPORTANT: Remove all objects from pockets such as
lighters and matches.
4
DRY2587N_SVG
1.
2.
3.
4.
Lead-In Cord
Earth/Ground Screw
Lead-In Cord Plug
Earth/Ground
Figure 21
Gas Dryer
NOTE: The wiring diagram is located in the control cabinet.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
29
Part No. 805989R1
Installation
Check Installation
1. Refer to Installer Checklist on the back cover of this manual
and make sure that unit is installed correctly.
2. Run washer with a test load to make sure it is operating properly and properly leveled.
a. Put about six pounds of laundry (four bath towels and
three jeans) into washer.
b. Close door.
c. Rapid advance to the final spin part of the cycle.
d. When washer spins at high speed, verify that it is stable.
e. If it is not, after cycle is complete, refer to Position and
Level the Washer to readjust leveling legs.
1
2
3
10A
0V
25
4
Check Heat Source
DRY2612N_SVG
1.
2.
3.
4.
Electric Dryers
Lead-In Cord
Earth/Ground Screw
Lead-In Cord Plug
Earth/Ground
1. Close the loading door and start the dryer in a heat setting (refer to the operation instructions).
2. After the dryer has operated for three minutes, the exhaust air
or exhaust pipe should be warm.
Figure 22
Gas Dryers
Earth/Ground Instructions
This appliance must be properly connected to protective earth/
ground. In the event of malfunction or breakdown, the earth/
ground will reduce the risk of electric shock by providing a path
of least resistance for electric current.
The dryer is equipped with a cord having an equipment-earth/
ground conductor and a 3 prong earth/ground plug. The plug
must be plugged into an appropriate outlet that is properly installed and connected to a protective earth/ground in accordance with
all local codes and ordinances.
Do not modify the plug provided with the dryer – if it will not fit
the outlet, have a proper outlet installed by a qualified electrician.
WARNING
Improper connection of the equipment earth/ground
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if
you are in doubt as to whether the dryer is properly
connected to a protective earth/ground.
W886
If the electrical supply does not meet the above specifications
and/or you are not sure your building has an effective earth/
ground, have a qualified electrician or your local electrical utility
company check it and correct any problems.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
IMPORTANT: This operation is to be conducted by
qualified personnel only.
1. To view the burner flame, remove the lower front panel of the
dryer.
2. Close the loading door and start the dryer in a heat setting (refer to the operation instructions). The dryer will start, the igniter will glow red and the main burner will ignite.
IMPORTANT: If all air is not purged out of gas line,
gas igniter may go off before gas is ignited. If this
happens, after approximately two minutes igniter
will again attempt gas ignition.
IMPORTANT: If igniter does not light, make sure gas
is turned on.
3. After the dryer has operated for approximately five minutes,
observe burner flame through lower front panel.
4. Adjust the air shutter to obtain a soft, uniform blue flame. (A
lazy, yellow-tipped flame indicates lack of air. A harsh, roaring, very blue flame indicates too much air.) Adjust the air
shutter as follows:
a. Loosen the air shutter lockscrew.
b. Turn the air shutter to the left to get a luminous yellowtipped flame, then turn it back slowly to the right to obtain
a steady, soft blue flame.
c. After the air shutter is adjusted for proper flame, tighten
the air shutter lockscrew securely.
5. Reinstall the lower front panel.
30
Part No. 805989R1
Installation
WARNING
To reduce the risk of serious injury or death, lower front panel must be in place during normal operation.
W158
6. After the dryer has operated for approximately three minutes,
exhaust air or exhaust pipe should be warm.
2
1
6
3
5
4
DRY212N_SVG
1.
2.
3.
4.
5.
Closed Position
Shut-Off Valve Handle
Air Shutter Lockscrew
Air Shutter
3.1 mm [1/8 in.] Pipe Plug (For checking manifold pressure)
6. Open Position
Figure 23
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
31
Part No. 805989R1
Operation
Operation
NOTE: Different fabrics will have different densities
and loads must be adjusted accordingly to meet machine loading specifications shown.
Operation Instructions for Washers
WARNING
Close Loading Door
Close loading door tightly. The washer will not operate with
the loading door open.
To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
W727
IMPORTANT: Prior to first wash, use an all-purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside of washer.
IMPORTANT: Remove all sharp objects from laundry to
avoid tears and rips to items during normal machine
operation.
Load Laundry
1. Load items loosely into wash drum. Safety: 9.5 kg [21
pounds] maximum dry clothes load based on electrical safety
tests performed to Australia/New Zealand safety standard for
Washing Machines. Energy Efficiency: 10 kg [22 pounds] capacity.
FLW2310N_SVG
Figure 25
NOTE: Small items such as baby socks may get
caught around the door. Place these articles inside
a mesh garment bag.
Add Laundry Supplies
1. Open dispenser drawer.
2. Measure and add low sudsing, high efficiency (HE) detergent
(1), bleach (2) and fabric softener (3) to the dispenser drawer.
IMPORTANT: If using non-HE detergent, avoid oversudsing by using 1/2 of the detergent manufacturer’s recommended amount.
3. Close dispenser drawer.
FLW2309N_SVG
Figure 24
2. When washing bulky items such as blankets and comforters,
use the DELICATE or DELICATES/COLD cycle. The cycle
includes agitation and final spin speeds that maintain the
load’s balance and minimize wear to the articles.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
32
Part No. 805989R1
Operation
NORMAL
HOT
NORMAL
WARM
PERM
PRESS
WARM
DELICATES
COLD
NORMAL
COLD
START
S
O
F
T
E
N
E
R
LIQUID BLEACH
FLW2361N_SVG
1
W
A
S
H
Figure 28
Insert Coins or Card
3
2
Insert Coins
FLW2360N_SVG
1. Detergent
2. Liquid Bleach
3. Fabric Softener
1. Insert coin(s) in coin slot.
2. Check pricing as seen on digital display.
Figure 26
Determine Proper Controls
The direction of the arrow indicates which control is for which
unit.
W388I_SVG
Figure 29
SWD960N_SVG
To Insert Card
Figure 27
Insert card into opening.
Set Fabric Selector and Wash Temperature
Push touchpad for NORMAL/HOT, NORMAL/WARM, NORMAL/COLD, PERM PRESS/WARM or DELICATES/COLD
cycle. Light indicates selection.
NOTE: Changes can be made to Fabric Selector setting
up until the first fill is complete.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
33
Part No. 805989R1
Operation
door cannot be opened when
this light is on.
START
START flashes one second on
and one second off when the
full vend price has been satisfied.
IMPORTANT: If washer fails to operate properly after
installation, make sure electrical service and water
supply faucets are turned on. Are all the controls properly set? Have a qualified service person refer to the
wiring diagram (located inside of washer control cabinet) and check for broken, loose or incorrect wiring.
NOTE: Once a cycle has started, the door can only be
opened by first unplugging the power cord and waiting
one minute.
DRY2633N_SVG
WARNING
Figure 30
Start Washer
To reduce the risk of bodily injury, do not remove
laundry from washer until all lights are out, and all
moving parts have stopped.
1. After vend price has been satisfied, push the START pad.
2. Door must be closed to start washer.
W092
NORMAL
HOT
NORMAL
WARM
PERM
PRESS
WARM
DELICATES
COLD
NORMAL
COLD
START
Operation Instructions for Dryers
WARNING
To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
FLW2362N_SVG
Figure 31
This appliance shall not be used to dry off solvents or dry cleaning fluids.
Indicator Lights
WASH
RINSE
W727
WASH is lit at the beginning
of a wash cycle and will remain lit until the wash cycle is
complete.
RINSE is lit at the beginning
of all RINSE cycles and will
remain lit until the rinse cycle
is complete.
SPIN
SPIN is lit for all spin cycles.
DOOR LOCKED
DOOR LOCKED is lit whenever the door is locked. The
IMPORTANT: Before using dryer for the first time, use
an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from
inside of dryer drum.
IMPORTANT: Remove all sharp objects from laundry to
avoid tears and rips to items during normal machine
operation.
IMPORTANT: Remove all objects from pockets such as
lighters and matches.
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
34
Part No. 805989R1
Operation
IMPORTANT: Oil affected items can ignite spontaneously, especially when exposed to heat sources such
as in a tumble dryer. The items become warm, causing
an oxidation reaction in the oil. Oxidation creates heat.
If the heat cannot escape, the items can become hot
enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so
create a fire hazard.
Clean Lint Filter
Clean lint filter before each use.
SWD1032N_SVG
Figure 34
Determine Proper Controls
The direction of the arrow indicates which control is for which
unit.
D608I_SVG
SWD960N_SVG
Figure 32
Figure 35
Load Laundry
1. Load clothes loosely into dryer drum (8.2 Kg [18.0 lbs.] maximum dry clothes load).
2. Add fabric softener sheet if desired.
IMPORTANT: To avoid damage to dryer, do not use
more than one fabric softener sheet per load.
Set Fabric Selector
Select HIGH TEMP, MED TEMP, LOW TEMP or DELICATES
by pushing touchpad.
NOTE: Always follow manufacturer's care labels.
HIGH
TEMP
MED
TEMP
LOW
TEMP
DELICATES
START
D717I_SVG
Figure 33
Close Loading Door
DRY2688N_SVG
1. Close loading door.
2. Dryer will not operate with the door open.
Figure 36
Insert Coins or Card
Insert Coins
1. Insert coin(s) in coin slot.
2. Check pricing as seen on digital display.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
35
Part No. 805989R1
Operation
HIGH
TEMP
LOW
TEMP
MED
TEMP
DELICATES
START
DRY2689N_SVG
Figure 39
W388I_SVG
IMPORTANT: The final part of dryer cycle occurs without heat (cool down cycle) to ensure that items in dryer
are left at a temperature that ensures that the items will
not be damaged.
Figure 37
To Insert Card
Insert card into opening.
WARNING
To prevent the risk of fire, never stop a dryer before
the end of the drying cycle unless all items are
quickly removed and spread out so that the heat is
dissipated.
W756
Indicator Lights
START
START is lit whenever the
dryer is not in a cycle, the full
vend price has been satisfied
and the dryer door is closed.
When the START pad is
pressed, the cycle will begin or
resume.
DRYING
DRYING is lit to indicate that
one of the heated cycles
(HIGH TEMP, MED TEMP,
LOW TEMP or DELICATES)
is currently in operation.
DRYING will turn off at the
end of a heated cycle or when
the COOL DOWN cycle begins.
COOL DOWN
COOL DOWN is lit whenever
the COOL DOWN portion of a
heated cycle is active.
DRY2633N_SVG
Figure 38
Start Dryer
1. To start dryer, push START pad.
2. To stop dryer at any time, open the door.
3. To restart the dryer, close door and push START pad. Cycle
is completed when time remaining reaches 00 minutes.
Remove knits when slightly damp because overdrying may cause
shrinkage. Do not tumble dry knit woolens.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
36
Part No. 805989R1
Maintenance
Maintenance
User-Maintenance Instructions
Lubrication
All moving parts are sealed in a permanent supply of lubricant or
are equipped with oilless bearings. Additional lubrication will not
be necessary.
•
•
Usually a mild soap solution will work. If there is an extreme
build-up of minerals from a hard water supply, the surfaces may
need to be cleaned with a lime removal chemical.
Replacing Hoses
Cold Weather Care
If the unit is delivered on a cold day (below freezing), or is stored
in an unheated room or area during the cold months, do not attempt to operate the washer until it has had a chance to warm up.
Water from the previous cycle may remain.
Extended Non-Use
IMPORTANT: To avoid possible property damage due
to flooding, turn off the water supply to the washer
whenever there will be an extended period of non-use.
Leave the loading door and dispenser drawer open during extended periods of non-use to allow the wash drum and drawer to dry
out and avoid a musty smell.
Care of Your Washer
Use only a damp or sudsy cloth for cleaning the control panel.
Some cleaning products may harm the finish on the control panel
or damage the interior. DO NOT use products that contain alcohol on the control panel. Wipe the panel dry after cleaning.
Wipe the washer cabinet as needed. If detergent, bleach or other
washing products are spilled on the cabinet, wipe immediately.
Some products will cause permanent damage if spilled on the
cabinet.
Do not use scouring pads or abrasive cleansers.
Hoses and other natural rubber parts deteriorate after extended
use. Hoses may develop cracks, blisters or material wear from the
temperature and constant high pressure they are subjected to.
All hoses should be checked on a monthly basis for any visible
signs of deterioration. Any hose showing the signs of deterioration listed above should be replaced immediately. All hoses
should be replaced every five years.
Filter Screens
Check the filter screens in the fill hoses for debris or damage every six months. Clean or replace them if necessary.
If the washer is filling with water slower than normal, check the
filter screens. Clean or replace them if necessary.
Order filter screen Part No. 803615 from the nearest authorized
parts distributor.
Cleaning Foreign Object Trap
The washer’s pump has a trap that may collect foreign objects.
The trap may need to be cleaned if water is draining slower than
usual. To clean:
1. Disconnect washer from electrical supply.
2. Remove two screws at bottom of the front access panel.
3. Rotate bottom of panel out and remove panel.
The wash drum will need no particular care although it may need
rinsing or wiping after an unusual load has been washed.
The outside of the door window can be cleaned with household
window cleaner.
Leave the door and dispenser drawer open slightly when not in
use. This will help keep them dry and prevent musty smells.
Running an occasional rinse cycle with bleach will help to avoid
a musty smell in the wash drum.
The outside perimeter of the door glass where the seal contacts the glass
The front surface of the door seal lip
4.
5.
6.
7.
NOTE: The pump may have some water in it. Use a
rag or a container to catch water. If the wash drum
is full of water, use a wet/dry shop vacuum to catch
the water.
With rag or vacuum ready, unscrew the cap on the left side of
the pump and remove trap.
Clean the debris from the trap.
Reinstall the trap and access panel.
Reconnect washer to electrical supply.
Cleaning Glass Sealing Area
In order to assure that the door properly seals against water leaks,
the following surfaces should be wiped off periodically:
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
37
Part No. 805989R1
Maintenance
Care of Your Dryer
WARNING
WARNING
To reduce the risk of an electric shock, serious injury or death, disconnect the electrical service to the
dryer before cleaning the interior.
W132
Dryer Interior
Wipe the surfaces using a soft cloth and household cleaner or a
non-abrasive paste of powdered laundry detergent and hot water,
followed by a short heat cycle with a load of rags.
To remove crayon or ball point ink off the dryer drum, put the
heat on high and use old rags in the dryer to absorb the crayon or
ink. If unsuccessful, contact the appliance dealer. DO NOT use
any chemicals in the dryer.
IMPORTANT: The use of chlorine bleach for removing
any discolorations should be avoided because bleach
could damage the finish.
Any disassembly requiring the use of tools must be
performed by a suitably qualified service person.
W299
The exhaust duct should be inspected after one year of use and
cleaned if necessary by a qualified service person to remove any
lint build-up. Inspect and clean exhaust duct every one to two
years as required thereafter.
NOTE: This recommended maintenance is not covered
under the terms of the warranty.
The weather hood should be checked frequently to make sure the
dampers move freely, dampers are not pushed in and that nothing
has been set against them.
Keep dryer area clear and free from combustible materials, gasoline and other flammable vapors and liquids.
Do not obstruct the flow of combustion and ventilation air.
NOTE: Verify proper operation after servicing.
Lint Filter
Cabinet
Wipe the dryer cabinet as needed. If detergent, bleach or other
washing products have been spilled on the dryer, wipe immediately. Some products will cause permanent damage if spilled on
the cabinet.
Control Panel
Use only a damp or sudsy cloth for cleaning the control panel.
Some spray pretreat products may harm the finish on the control
panel. DO NOT use products that contain alcohol on the control
panel.
CLEAN THE LINT FILTER BEFORE DRYING EACH LOAD.
(Refer to Figure 40 for lint filter location.) Cleaning the lint filter
is important because a layer or pad of lint on the filter will block
the flow of air through the dryer, thus reducing the efficiency of
the dryer. The clothes will take longer to dry and energy will be
wasted.
The lint filter may be washed if needed. Annually remove lint filter and screw to vacuum the duct under it.
Exhaust System
WARNING
1
To reduce the risk of electric shock, disconnect the
electrical service to the dryer before cleaning.
D608I_SVG1
W043
1. Lint Filter
Figure 40
Reinstallation of Shipping Materials
To prevent damage while moving the unit, the shipping materials
MUST be reinstalled.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
38
Part No. 805989R1
Maintenance
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect washer from electrical supply.
Remove two screws at bottom of front access panel.
Rotate bottom of panel out and remove panel.
Attach shipping brace to weight and base using four bolts and
washers. Refer to Figure 41 .
Reinstall front access panel.
Go to rear of washer to install rear shipping bolt, washer,
spacer assemblies.
Insert shipping bolt assemblies into each shipping bolt hole.
Refer to Figure 42 .
Tighten bolt while pressing washer against rear panel to ensure spacer is fully inserted.
For Energy Conservation
•
•
•
•
•
•
•
•
•
•
Make sure the lint filter is always clean.
Do not overload dryer.
Do not overdry clothes.
Remove items to be ironed while still damp.
Large loads of similar fabrics dry the most efficiently. However, dry permanent press in smaller loads to prevent wrinkling.
Use the correct temperature FABRIC SELECTOR setting for
the type of fabric being dried.
Locate your dryer so the exhaust duct is as short and straight
as possible.
Do not open the door during the drying cycle.
Plan to do your laundry on low humidity days; your clothes
will dry faster.
Should you plan to dry several loads, do them one after another, then you do not have to reheat the dryer unit’s interior
parts each time.
1
FLW2296N_SVG
1. Shipping Brace
Figure 41
1
FLW2297N_SVG
1. Shipping Bolt Assembly
Figure 42
Motor Overload Protector
The dryer’s motor overload protector stops the motor automatically in the event of an overload. After cooling, the overload protector will reset itself. Dryer can be restarted by pressing the
START pad. If overload protector cycles again, remove the dryer
from use and call the service person to correct the problem.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
39
Part No. 805989R1
Troubleshooting
Troubleshooting
Try these troubleshooting tips before making a service call. They
may save you time and money.
Washer Symptom
Possible Cause/Solution
Won’t Fill
•
•
•
•
•
•
•
•
Make sure power cord is plugged all the way into the electrical outlet.
Check the laundry room fuse or circuit breaker.
Make sure that the controls are properly set.
Press START keypad.
Make sure that the loading door is closed tightly.
Make sure hot and cold water faucets are turned on.
Make sure that the fill hoses are not kinked or twisted.
Clean the screens in the water mixing valve and the filter screens located at the faucet
end of the fill hoses.
Won’t Start
•
•
•
•
•
•
•
Make sure power cord is plugged all the way into the electrical outlet.
Check the laundry room fuse or circuit breaker.
Make sure that the controls are properly set.
Press START keypad.
Make sure that the loading door is closed tightly.
Insert coin(s) or card.
Make sure door latch is properly adjusted relative to door lock.
Won’t Spin/Tumble
•
•
•
•
•
•
•
Make sure power cord is plugged all the way into the electrical outlet.
Check the laundry room fuse or circuit breaker.
Make sure that the controls are properly set.
Press START keypad.
Make sure that the loading door is closed tightly.
Broken drive belt. Call the service person.
Foreign object trap in pump may be clogged. Clean the trap. Refer to Maintenance
section.
Stops/Pauses During Cycle
•
•
•
Pauses are part of the washer’s normal operation.
Check the laundry room fuse or circuit breaker.
Wash load may be unbalanced. Washer will stop and then restart spin automatically.
Won’t Drain
•
•
•
•
Make sure drain hose is not kinked or twisted.
Make sure drain hose is not clogged.
Make sure drain receptacle is not clogged.
Refer to the Installation instructions to make sure that the drain hose has been properly installed.
Foreign object trap in pump may be clogged. Clean the trap. Refer to Maintenance
section.
•
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
40
Part No. 805989R1
Troubleshooting
Washer Symptom
Water Leaks
Possible Cause/Solution
•
•
•
•
•
•
•
•
Too Many Soap Suds
•
•
•
Vibrates/Moves Slightly
•
•
•
Check that fill hoses are properly installed on the faucets and the washer’s water mixing valve.
Check the condition of the fill hoses. Replace fill hoses every five years.
Make sure drain receptacle is not clogged.
Check laundry room plumbing.
Check the condition of the rubber door gasket for tears or holes.
Laundry load may be oversudsing. Make sure you are using low-sudsing, high efficiency (HE) detergent.
Laundry load may be overloaded. Make sure you are using proper load sizes.
Make sure outside perimeter of the door glass where seal contacts glass is clean.
Laundry load may be oversudsing. Make sure you are using low-sudsing, high efficiency (HE) detergent.
Make sure you are using the amount of detergent recommended on the detergent’s label. If using non-HE detergent, use only 1/2 of the detergent manufacturer's recommended amount.
Laundry load may be overloaded. Make sure you are using proper load sizes.
Make sure washer is level. Uneven leveling can cause vibration.
Make sure washer is installed on a solid, sturdy and level floor. The washer should
not be installed on carpeting, soft tile, a platform or other weakly supported structures.
Make sure rubber feet are installed on all four leveling legs. Refer to Position and
Level the washer.
Is Noisy
•
•
Make sure washer is level. Uneven leveling can cause vibration.
Some sounds may be a part of normal operation for a frontload washer, such as clicking noise when door locks and clicking noise from balance ring during agitate part of
cycle.
Load is too Wet
•
Wash load may be unbalanced. The washer may have limited the spin speed to prevent damage to the machine. Redistribute the load.
Load is too small. Add items to make full load.
•
Wrong Water Temperature
•
•
•
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Make sure that the controls are properly set.
Check fill hoses. Make sure hot faucet hose is connected to hot mixing valve (indicated with “H” on the valve bracket) and cold faucet is connected to cold mixing valve
(indicated with “C” on the valve bracket).
Make sure laundry room water heater is adjusted properly.
41
Part No. 805989R1
Troubleshooting
Dryer Symptom
Dryer won’t start
Possible Cause/Solution
•
•
•
•
•
•
Dryer won’t heat
•
•
•
•
•
•
Dryer doesn’t dry clothes satisfactorily
•
•
•
•
•
Dryer is noisy
•
•
•
Insert coin(s) or card, if required.
For dryers equipped with a power cord, make sure the power
cord is plugged all the way into the electrical outlet.
Make sure loading door is closed.
Press START pad.
Make sure the laundry room fuse(s) isn’t blown or loose, or
circuit breakers aren’t open.
Check if motor overload protector has cycled. Wait 10 minutes and try again.
Make sure the laundry room fuse(s) isn’t blown or loose, or
circuit breakers aren’t open.
Make sure controls are in a HEAT setting.
Gas dryer only – Make sure equipment and main gas line
valve is turned on.
Check exhaust duct to outside to see if it is kinked, blocked or
needs cleaning.
Check weather hood to make sure flapper moves freely, has
not been pushed in or has not been blocked.
Gas dryer only – Is the limit thermostat open? Reset the thermostat and restart the dryer.
Check exhaust duct to outside to see if it is kinked, blocked or
needs cleaning.
Check weather hood to make sure flapper moves freely, has
not been pushed in or has not been blocked.
Clean the lint filter.
Make sure the load isn’t too small. Small loads may not tumble properly or dry evenly.
Check load being dried. Heavy items dried with lightweight
items will not dry as quickly as the rest of the load.
Check dryer for foreign objects (nails, coins, bobby pins, metal, plastic toys, etc.). Remove items from dryer.
Make sure dryer is level. Uneven leveling can cause vibration.
Normal operating sounds include the heat source going on
and off and the humming of air moving through the dryer and
exhaust system.
Clothes are too wrinkled
•
•
Check heat setting. Overdrying can cause wrinkling.
Check load size. Large loads may not tumble properly and
may cause wrinkling.
Clothes have odor
•
Check room for odors before drying clothes. Any odor (fried
foods, paint, varnish, cleaners, burning wood, etc.) will transfer to clothing as the dryer draws air from the room.
Ventilate room before drying clothes.
•
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
42
Part No. 805989R1
Contact Information
Contact Information
If service is required, contact the nearest Factory Authorized
Service Center.
Serial Number _______________________________
If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit, contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: +1 (920) 748-3121 Ripon, Wisconsin
+32 56 41 20 54 Wevelgem, Belgium
When calling or writing about your unit, PLEASE GIVE THE
MODEL AND SERIAL NUMBERS. The model and serial numbers are located on the serial plate. The serial plate will be in the
location shown in Figure 43 .
Date Purchased ______________________________
Model Number ______________________________
Please include a copy of your bill of sale and any service receipts
you have.
WARNING
To reduce the risk of serious injury or death, DO
NOT repair or replace any part of the unit or attempt
any servicing unless specifically recommended in
the user-maintenance instructions or in published
user-repair instructions that you understand and
have the skills to carry out.
W329
If replacement parts are required, contact the source from where
you purchased your unit or call +1 (920) 748-3950 or +32 56 41
20 54 for the name and address of the nearest authorized parts
distributor.
1
DRY2527N_SVG
1. Serial Plate
Figure 43
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
43
Part No. 805989R1
Installer Checklist
Installer Checklist
Fast Track for Installing the Stacked Washer/Dryer
1
Position Unit Near Installation Area.
6
Connect Dryer Exhaust
System.
CHECK
CHECK
SWD997N_SVG1
2
Remove the Shipping Materials and Install Plugs.
7
Position and Level the
Washer.
CHECK
CHECK
SWD1029N_SVG1
FLW2359N_SVG
3
Connect Fill Hoses.
8
COLD
Wipe Out Inside of
Washer and Dryer
Drums.
HOT
CHECK
CHECK
SWD1030N_SVG
FLW2216N_SVG1
4
Connect Drain Hose to
Drain Receptacle or Drain
Outlet to Drain System.
9
Connect Washer and
Dryer to Electrical
Power.
CHECK
CHECK
TLW2170N_SVG
SWD1026N_SVG1 SWD1002N_SVG1
5
GAS ONLY
•
•
Connect Gas Supply
Pipe.
Check for Gas Leaks.
10
Recheck Steps.
11
Start and Run Dryer in Heat Setting to Verify Dryer is
Heating.
D233I_SVG1
CHECK
CHECK
Refer to the manual for more detailed information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
44
Part No. 805989R1
Download PDF