Model No.
TH-85VX200W
TH-103VX200W
Operating Instructions
High Definition Plasma Display
English
Please read these instructions before operating your set
and retain them for future reference.
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that you will have many years of
enjoyment from your new Plasma Display.
To obtain maximum benefit from your set, please read these Instructions before making
any adjustments, and retain them for future reference.
Retain your purchase receipt also, and note down the model number and serial number of
your set in the space provided on the rear cover of these instructions.
Visit our Panasonic Web Site
http://panasonic.net
ii
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: To reduce the risk of electric shock, do not remove cover or back.
No user-serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with
arrow-head within a triangle
is intended to tell the user
that parts inside the product
are a risk of electric shock
to persons.
The exclamation point within
a triangle is intended to
tell the user that important
operating and servicing
instructions are in the papers
with the appliance.
WARNING : To prevent damage which may result in fire or shock hazard, do not expose this apparatus to
rain or moisture.
Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set.
(including on shelves above, etc.)
WARNING : 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing
to qualified service personnel.
2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin
grounding-type power plug. This plug will only fit a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
Important Safety Instructions
1)
2)
3)
4)
5)
6)
7)
8)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11) Only use attachments / accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart / apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.
iii
Important Safety Notice
WARNING
1) To prevent damage which may result in fire or shock hazard, do not expose this appliance to dripping
or splashing.
Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked flame sources, such as lighted candles, should be placed on / above the set.
2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified
service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type
power plug. This plug will only fit an earthing-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the earthing plug.
4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments which are relatively free of electromagnetic fields.
Using this appliance near sources of strong electromagnetic fields or where electrical noise may overlap with the
input signals could cause the picture and sound to wobble or cause interference such as noise to appear.
To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic fields.
IMPORTANT INFORMATION
If a display is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many
injuries, particularly to children, can be avoided by taking simple precautions such as:
• Using cabinets or stands recommended by the manufacturer of the display.
• Only using furniture that can safely support the display.
• Ensuring the display is not overhanging the edge of the supporting furniture.
• Not placing the display on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture
and the display to a suitable support.
• Not standing the displays on cloth or other materials placed between the display and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the display or its controls.
IMPORTANT: THE MOULDED PLUG
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This display is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is
fitted in this plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10
amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
ASA
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic dealer.
Do not cut off the mains plug.
Do not use any other type of mains lead except the one supplied with this display.
The supplied mains lead and moulded plug are designed to be used with this display to avoid
interference and for your safety.
If the socket outlet in your home is not suitable, get it changed by a qualified electrician.
If the plug or mains lead becomes damaged, purchase a replacement from an authorized dealer.
WARNING : — THIS DISPLAY MUST BE EARTHED.
How to replace the fuse. Open the fuse compartment with a screwdriver and replace the fuse.
iv
Table of Contents
Important Safety Instructions................................. iii
Important Safety Notice .......................................... iv
Safety Precautions ................................................... 2
3D Safety Precautions ............................................. 5
Accessories .............................................................. 7
Accessories Supply ................................................. 7
Remote Control Batteries ........................................ 7
Connections .............................................................. 8
AC cord connection and fixing, cable fixing ............. 8
Video equipment connection ................................. 10
AUDIO OUT connection ........................................ 10
HDMI connection ....................................................11
COMPONENT / RGB IN connection ......................11
PC Input Terminals connection .............................. 12
SERIAL Terminals connection ............................... 13
Power On / Off......................................................... 14
Selecting the input signal ...................................... 16
Basic Controls ........................................................ 17
ASPECT Controls ................................................... 19
Viewing 3D images ................................................. 20
3D Eyewear ........................................................... 20
To view the 3D images .......................................... 22
Troubleshooting for 3D Eyewear .......................... 23
Table of images that can be seen for each 3D
Picture Format and the source image format ........ 23
On-Screen Menu Displays ..................................... 24
Adjusting Pos. /Size ............................................... 25
Picture Adjustments ............................................... 28
Advanced settings ................................................. 30
Colour space adjustment (Colour Gamut) ............. 32
Picture Profiles ....................................................... 34
Saving profiles ....................................................... 35
Loading profiles ..................................................... 36
Editing profiles ....................................................... 37
Locking profiles ..................................................... 38
Sound Adjustment .................................................. 40
SDI Sound Output ................................................. 40
Setup menu ............................................................. 41
Component / RGB-in select ................................... 41
YUV / RGB-in select .............................................. 41
External scaler mode ............................................. 42
Power save ............................................................ 43
PC Power management: ....................................... 43
Auto power off ....................................................... 43
OSD design ........................................................... 43
OSD position ......................................................... 43
OSD Language ...................................................... 43
3D Settings ............................................................ 44
Signal menu .......................................................... 45
Screensaver .......................................................... 47
Extended life settings ............................................ 48
Customizing the Input labels ................................. 51
Network Setup ....................................................... 52
Options Adjustments ............................................. 53
3D Safety Precautions (To hide 3D Safety
Precautions) .......................................................... 54
Using FUNCTION button ........................................ 54
Using Network Function ........................................ 55
Example of Network Connection ........................... 55
Command Control ................................................. 55
PJLink™ Protocol .................................................. 56
Using Web Browser Control .................................. 57
Before Using Web Browser Control....................... 57
Access from Web Browser .................................... 57
Display Control (BASIC CONTROL/OPTION
CONTROL Screen) ............................................... 58
NETWORK SETTING (Network Setup Screen) .... 59
Password Setting (Password Setup Screen) ........ 59
Troubleshooting ..................................................... 60
List of Aspect Modes ............................................. 61
Applicable Input Signals ........................................ 62
Shipping condition ................................................. 63
Specifications ......................................................... 64
Trademark Credits
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Inc., USA.
• SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.
• HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention
to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
1
Safety Precautions
WARNING
Setup
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Panasonic Corporation.)
• Pedestal ......................................................................... TY-ST85P12 (for TH-85VX200W)
TY-ST103PF9 (for TH-103VX200W)
• Floor stand ..................................................................... TY-ST85PF12 (for TH-85VX200W)
• Wall-hanging bracket (vertical) ...................................... TY-WK85PV12 (for TH-85VX200W)
TY-WK103PV9 (for TH-103VX200W)
• BNC Dual Video Terminal Board .................................... TY-FB9BD
• HD-SDI Terminal Board with audio ................................ TY-FB10HD
• Dual Link HD-SDI Terminal Board .................................. TY-FB11DHD
• Ir Through Terminal Board.............................................. TY-FB9RT
• DVI-D Terminal Board .................................................... TY-FB11DD
• AV Terminal Box ............................................................. TY-TB10AV
Always be sure to ask a qualified technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from
being played with by young children, creating the potential risk of suffocation.
Do not place the Plasma Display on sloped or unstable surfaces.
• The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma Display.
• If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result
in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic
dealer.
Transport only in upright position!
• Transporting the unit with its display panel facing upright or downward may cause damage to the internal
circuitry.
Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table
cloths and curtains.
For sufficient ventilation;
(TH-85VX200W)
If using the pedestal (optional accessory), leave a space of 10 cm or more at the top, left and right, and 15 cm
or more at the rear, and also keep the space between the bottom of the display and the floor surface.
If using some other setting-up method, follow the manual of it. (If there is no specific indication of installation
dimension in the installation manual, leave a space of 10 cm or more at the top, bottom, left and right, and 15
cm or more at the rear.)
(TH-103VX200W)
If using the pedestal (optional accessory), leave a space of 30 cm or more at the top, left and right, and 20 cm
or more at the rear, and also keep the space between the bottom of the display and the floor surface.
If using some other setting-up method, follow the manual of it. (If there is no specific indication of installation
dimension in the installation manual, leave a space of 30 cm or more at the top, bottom, left and right, and 20
cm or more at the rear.)
2
Safety Precautions
When using the Plasma Display
The Plasma Display is designed to operate on 200 - 240 V AC, 50/60 Hz.
Do not cover the ventilation holes.
• Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.
Do not stick any foreign objects into the Plasma Display.
• Do not insert any metal or flammable objects into the ventilations holes or drop them onto the Plasma Display, as
doing so can cause fire or electric shock.
Do not remove the cover or modify it in any way.
• High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection,
adjustment and repair work, please contact your local Panasonic dealer.
Ensure that the mains plug is easily accessible.
An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection.
Do not use any power supply cord other than that provided with this unit.
• Doing so may cause fire or electric shocks.
Securely insert the power supply plug as far as it will go.
• If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall
socket is loose, they shall not be used.
Do not handle the power supply plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug body, not the cable.
• Do not damage the cable, make any modifications to it, place heavy objects on top of it, heat it, place it near any
hot objects, twist it, bend it excessively or pull it. To do so may cause fire and electric shock. If the power cable is
damaged, have it repaired at your local Panasonic dealer.
If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug
from the wall outlet.
To prevent the spread of fire, keep candles or other open flames away from this product at all times.
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out
from the Plasma Display, immediately unplug the power supply plug from the wall outlet.
• If you continue to use the Plasma Display in this condition, fire or electric shock could result. After checking that
the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing
the Plasma Display yourself is extremely dangerous, and shall never be done.
If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet
becomes damages, disconnect the power supply plug immediately.
• A short circuit may occur, which could cause fire. Contact your local Panasonic dealer for any repairs that need to be made.
3
Safety Precautions
CAUTION
When using the Plasma Display
Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.
• Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands
or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.
Be sure to disconnect all cables before moving the Plasma Display.
• If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged,
and fire or electric shock could result.
Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any
cleaning.
• Electric shocks can result if this is not done.
Clean the power cable regularly to prevent it becoming dusty.
• If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in fire.
Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.
Do not burn or breakup batteries.
• Batteries must not be exposed to excessive heat such as sunshine, fire or the like.
This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment.
Install your infrared sensor in a place away from direct or reflected light from your Plasma Display.
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in
which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until
the surface is dry.
• Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may
become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner,
otherwise the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been
added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the
cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods
in contact with articles made from rubber or PVC.
4
Safety Precautions
3D Safety Precautions
WARNING
Small Parts
3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small
children to avoid accidental ingestion.
Disassembly
Do not disassemble or modify the 3D Eyewear.
Lithium Battery
Batteries must not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION
To enjoy 3D images safely and comfortably, please read these instructions fully.
Use for commercial applications and public viewing
Someone in authority should responsibly convey the precautions for use of the 3D Eyewear to the user.
3D Eyewear
Do not drop, exert pressure on, or step on the 3D Eyewear.
Always store the 3D Eyewear in the case provided when not in use.
Be careful of the tips of the frame when putting on the 3D Eyewear.
Be careful not to trap a finger in the hinge section of the 3D Eyewear.
Pay special attention when children are using the 3D Eyewear.
3D Eyewear should not be used by children younger than 5 - 6 years old, as a guideline.
All children must be fully supervised by parents or guardians who must ensure their safety and health
throughout the using 3D Eyewear.
5
Safety Precautions
Viewing 3D Content
Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc.
When preparing your own 3D content, ensure that it is properly produced.
Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other
existing medical conditions.
Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other
uncomfortable sensation.
Take an appropriate break after viewing a 3D movie.
Take a break of between 30 - 60 minutes after viewing 3D content on interactive devices such as 3D games
or computers.
Be careful not to strike the screen or other people unintentionally. When using the 3D Eyewear the distance
between the user and screen can be misjudged.
The 3D Eyewear must only be worn when viewing 3D content.
If you do not look toward the screen for a while when viewing 3D images, the 3D Eyewear may be turned off
automatically.
If you suffer from any eyesight problems (short / far-sighted, astigmatism, eyesight differences in left and
right), please ensure to correct your vision before using the 3D Eyewear.
Stop using the 3D Eyewear if you can clearly see double images when viewing 3D content.
When the multiple plasma displays are placed side by side, 3D images may be seen doubly due to interference
among them. Place each display at an appropriate location to avoid it.
Do not use the 3D Eyewear at a distance less than the recommended distance.
View from at least the recommended distance (3 times the effective height of the screen).
TH-85VX200W: 3.2 m or more
TH-103VX200W: 3.9 m or more
When the top and bottom area of the screen is blackened, such as movies, view the screen at a distance 3
times further than the height of the actual image. (That makes the distance closer than above recommended
figure.)
3D Eyewear Use
Before using the 3D Eyewear, ensure no breakable objects surrounding the user to avoid any accidental
damage or injury.
Remove the 3D Eyewear before moving around to avoid falling or accidental injury.
Always put the 3D Eyewear in the case (supplied) after use.
Use the 3D Eyewear only for the intended purpose and nothing else.
Do not use 3D Eyewear in the condition of high temperature.
Do not use if the 3D Eyewear is physically damaged.
Do not use any devices that emit the infrared signals near the 3D Eyewear, as this may cause the 3D Eyewear
false operations.
Do not use devices (such as mobile phones or personal transceivers) that emit strong electromagnetic waves
near the 3D Eyewear as this may cause the 3D Eyewear to malfunction.
Stop using the 3D Eyewear immediately if a malfunction or fault occurs.
Stop using the 3D Eyewear immediately if you experience any redness, pain, or skin irritation around the nose
or temples.
In rare cases, the materials used in the 3D Eyewear may cause an allergic reaction.
Lithium Battery
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
6
Accessories
Accessories Supply
Check that you have the accessories and items shown
Remote Control
Transmitter
N2QAYB000562
Batteries for
the Remote
Control
Transmitter
(R6 (UM3) Size × 2)
Fixing band × 2
TMME203
Power supply cord TH-85VX200W
Clamper × 1
TMM15412-2
Use the clamper
when connecting a
LAN cable.
(see page 55)
3D Eyewear set
(see page 20)
Screwdriver
These accessories will be used by professional installers when
they install the unit.
TH-85VX200W
Eyebolt × 1
Allen wrench
Eyebolt cap × 1
(M12)
For 3D Eyewear
(see page 21)
TH-103VX200W
Eyebolt cap × 1
Operating Instructions
Ferrite core × 2
J0KG00000014
Eyebolt × 1
(M16)
Allen wrench
Noise cut filter
TXZDM011MBE
Use the Ferrite cores and Noise cut filter to comply
with the EMC standard. (see page 55)
Remote Control Batteries
Requires two R6 batteries.
1. Pull and hold the hook, then open
the battery cover.
2. Insert batteries - note correct
polarity ( + and -).
Close
Open
Hook
Helpful Hint:
For frequent remote control
users, replace old batteries
with Alkaline batteries for
longer life.
“R6 (UM3)” size
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.
6. Do not burn or breakup batteries.
Batteries must not be exposed to excessive heat such as sunshine, fire or the like.
7
Connections
AC cord connection and fixing, cable fixing
TH-85VX200W
– AC cord fixing
Unplug the AC cord
Close
Push until
the hook clicks.
1 Plug the AC cord into
the display unit.
Plug the AC cord until
it clicks.
2 Fix the AC cord with
the clamper.
Note:
Make sure that the
AC cord is locked on both
the left and right sides.
Open
2. Pull off.
1. Keep the
knob pressed.
– Cable fixing bands
Unplug the
AC cord
pressing the
two knobs.
Note:
When disconnecting the AC
cord, be absolutely sure to
disconnect the AC cord plug
at the socket outlet first.
Secure any excess cables with bands as required.
Note:
Two fixing bands are supplied with this unit. In case of securing cables at three positions, please purchase it separately.
Pass the attached cable
fixing band through the
clip as shown in the
figure.
To secure cables connected to Terminals, wrap the cable fixing band around them
then pass the pointed end through the locking block, as shown in the figure.
While ensuring there is sufficient slack in cables to minimize stress (especially
in the power cord), firmly bind all cables with the supplied fixing band.
To tighten:
To loosen:
Push the catch
Pull
1
8
2
Pull
Connections
TH-103VX200W
– AC cord fixing
Unplug the AC cord
Close
Push until
the hook clicks.
1 Plug the AC cord into
Open
the display unit.
Plug the AC cord until
it clicks.
2 Fix the AC cord with
the clamper.
Note:
Make sure that the
AC cord is locked on both
the left and right sides.
– Cable fixing bands
2. Pull off.
1. Keep the
knob pressed.
Unplug the
AC cord
pressing the
two knobs.
Note:
When disconnecting the AC
cord, be absolutely sure to
disconnect the AC cord plug
at the socket outlet first.
Secure any excess cables with bands as required.
Note:
Two fixing bands are supplied with this unit. In case of securing cables at four positions, please purchase it separately.
Pass the attached cable To secure cables connected to Terminals, wrap the cable fixing band around them
fixing band through the then pass the pointed end through the locking block, as shown in the figure.
clip as shown in the While ensuring there is sufficient slack in cables to minimize stress (especially
in the power cord), firmly bind all cables with the supplied fixing band.
figure.
To tighten:
To loosen:
Push the catch
Pull
1
2
Pull
9
Connections
Video equipment connection
SERIAL
Control the Plasma Display
by connecting to PC
(see page 13)
LAN
Connect to a
network to control
the unit.
(see page 55)
COMPONENT/RGB IN
Component/RGB Video
Input Terminal
(see page 11)
3D SHUTTER OUT
Connect the 3D IR
TRANSMITTER
(optional accessory).
PC IN
PC Input Terminal
Connect to video
terminal of PC or
equipment with
Y, PB(CB) and
PR(CR) output
(see page 12).
AUDIO OUT
Connect to sound
equipment.
(see below)
AV IN (HDMI 1-4)
HDMI Input Terminal
(see page 11)
AUDIO OUT connection
Note:
Additional equipment and cables shown are not supplied with this set.
Stereophonic sound code
audio equipment
line-in
10
SLOT
Terminal board
(optional accessories)
insert slot
(see page 2)
Connections
HDMI connection
[Pin assignments and signal names]
Pin No.
Signal name
Pin No.
Signal name
T.M.D.S Clock
Shield
1
T.M.D.S Data2+
11
2
T.M.D.S Data2
Shield
T.M.D.S Data2T.M.D.S Data1+
T.M.D.S Data1
Shield
T.M.D.S Data1T.M.D.S Data0+
T.M.D.S Data0
Shield
T.M.D.S Data0T.M.D.S Clock+
12
T.M.D.S Clock-
13
CEC
14
Reserved
(N.C. on device)
3
4
5
6
7
8
9
10
15
16
SCL
SDA
DDC/CEC
Ground
+5V Power
Hot Plug Detect
17
18
19
HDMI cables
HDMI cables
HDMI
AV OUT
19
18
HDMI
AV OUT
HDMI
AV OUT
HDMI
AV OUT
3 1
DVD Player or SET-TOP-BOX
(HDMI compatible machines only)
4 2
Note:
Additional equipment and HDMI cable shown are not supplied with this set.
COMPONENT / RGB IN connection
DVD Player
Y
PB
PR
Y, PB, PR,
OUT
Computer
RGB Camcorder
L
R
AUDIO
OUT
Notes:
• Additional equipment and cables shown are not supplied with this set.
• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component” (when Component signal connection)
or “RGB” (when RGB signal connection). (see page 41)
• Accepts only RGB signals with “Sync on G”.
11
Connections
PC Input Terminals connection
(Female)
COMPUTER
Audio
Stereo mini plug (M3)
Connect a cable which matches
the audio output terminal on the computer.
Conversion adapter
(if necessary)
Mini D-sub 15p
RGB
PC cable
(Male)
Notes:
• With regard to the typical PC input signals that are described in the applicable input signals list (see page 62), adjustment
values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight
PC input signal types that are not included in the list.
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
• The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080
dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible
to show fine detail with sufficient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will
need to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
• To use sync input VBS signals, use the connector which incorporates a 75-ohm termination resistance and which is
available on the market, for the connection of the HD connector where the VBS signals are to be input.
• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”
(when Component signal connection) or “RGB” (when RGB signal connection). (see page 41)
Signal Names for Mini D-sub 15P Connector
5
4
10 9
3
2
8
1
7
6
15 14 13 12 11
Pin Layout for PC Input
Terminal
12
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
1
R (PR/CR)
6
GND (Ground)
11
NC (not connected)
2
G (Y)
7
GND (Ground)
12
SDA
3
B (PB/CB)
8
GND (Ground)
13
HD/SYNC
4
NC (not connected)
9
+5 V DC
14
VD
5
GND (Ground)
10
GND (Ground)
15
SCL
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to
“RS-232C”. (see page 52)
(Male)
COMPUTER
RS-232C Straight cable
(Female)
9
5
8
4
7
3
6
2
1
D-sub 9p
Notes:
• Use the RS-232C straight cable to connect the computer to the Plasma Display.
• The computer shown is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface
specification, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the
sending and receiving of control data which satisfies
the conditions given below. Use a computer application
such as programming language software. Refer to the
documentation for the computer application for details.
Communication parameters
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
Flow control
C1 C2 C3
Start
(02h)
:
P1 P2 P3 P4 P5
Signal names for D-sub 9P connector
Pin No.
2
3
5
4 • 6
7
8
1 • 9
Details
RXD
TXD
GND
Non use
(Shorted in this set)
NC
These signal names are those of computer specifications.
RS-232C compliant
Asynchronous
9600 bps
None
8 bits
1 bit
-
Basic format for control data
The transmission of control data from the computer
starts with a STX signal, followed by the command, the
parameters, and lastly an ETX signal in that order. If there
are no parameters, then the parameter signal does not
need to be sent.
STX
Pin layout for SERIAL Terminal
Command
Command
PON
POF
AVL
AMT
IMS
ETX
Colon
Parameter(s)
(1 - 5 bytes)
3-character
command (3 bytes)
End
(03h)
Notes:
• If multiple commands are transmitted, be sure to wait for
the response for the first command to come from this unit
before sending the next command.
• If an incorrect command is sent by mistake, this unit will
send an “ER401” command back to the computer.
• S1A and S1B of Command IMS are available only when
a dual input terminal board is attached.
DAM
Parameter
None
None
**
0
1
None
SL1
S1A
S1B
YP1
HM1
HM2
HM3
HM4
PC1
None
ZOOM
FULL
JUST
NORM
ZOM2
ZOM3
SJST
SNOM
SFUL
14:9
Control details
Power ON
Power OFF
Volume 00 - 63
Audio MUTE OFF
Audio MUTE ON
Input select (toggle)
SLOT input (SLOT INPUT)
SLOT input (SLOT INPUT A)
SLOT input (SLOT INPUT B)
COMPONENT/RGB IN input
(COMPONENT)
HDMI 1 input (HDMI1)
HDMI 2 input (HDMI2)
HDMI 3 input (HDMI3)
HDMI 4 input (HDMI4)
PC IN input (PC)
Screen mode select (toggle)
Zoom1 (For Video/SD/PC signal)
16:9
Just (For Video/SD signal)
4:3 (For Video/SD/PC signal)
Zoom2 (For HD signal)
Zoom3 (For HD signal)
Just (For HD signal)
4:3 (For HD signal)
4:3 Full (For HD signal)
14:9
With the power off, this display responds to PON command
only.
13
Power On / Off
Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug securely to the Plasma
Display with the clamper. (see page 8, 9)
Connecting the plug to the Wall Outlet
Notes:
• Main plug types vary between countries. The power
plug shown at right may, therefore, not be the type
fitted to your set.
• When disconnecting the AC cord, be absolutely
sure to disconnect the AC cord plug at the socket
outlet first.
Press the Power switch on the Plasma Display to
turn the set on: Power-On.
Right side surface
Main Power
On / Off Switch
Remote Control
Sensor
Power Indicator
Power Indicator: Green
Press the
button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the
button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the
unit, when the Plasma Display is on or in standby mode.
switch on the
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
14
Power On / Off
When first switching on the unit
Following screen will be displayed when the unit is turned on for the first time.
Select the items with the remote control. Unit buttons are invalid.
OSD Language
OSD Language
1
English (UK)
Select the language.
Deutsch
Français
2
Set.
Italiano
Español
ENGLISH (US)
Notes:
• Once the language is set, this screen won’t be displayed
when switching on the unit next time.
• After the setting, language selection can be done from
the Setup menu. (see page 43)
3D Safety Precautions
If the power is turned on for the next and
subsequent times, 3D Safety Precautions
are displayed.
If you do not want to show this message, set
to hide it in the “3D Safety Precautions” on
the Options menu. (see page 54)
Русский
When 3D images will be viewed by unspecified number of
people or used for commercial applications, someone in
authority should convey the following precautions.
These precautions should be followed in the home as well.
3D Viewing/ 3D Content/ Viewing distance/ 3D Eyewear
recommendations
- To enjoy 3D images safely and comfortably, please
read the Operating Instructions fully.
15
Selecting the input signal
Press to select the input signal to be played back from the equipment
which has been connected to the Plasma Display.
INPUT
HDMI1
HDMI2
HDMI3
HDMI input terminals in HDMI 1 to HDMI 4.
HDMI4
COMPONENT
PC
Component or RGB input terminal in COMPONENT/RGB IN.*
PC input terminal in PC IN.
* “COMPONENT” may be displayed as “RGB” depending on the
setting of “Component/RGB-in select”. (see page 41)
When an optional Terminal Board is installed:
INPUT
HDMI1
HDMI2
HDMI3
HDMI4
SLOT INPUT
COMPONENT
PC
Input terminal in Terminal Board
When a dual input Terminal Board is installed, “SLOT INPUT A” and “SLOT INPUT B”
are displayed.
Using dedicated buttons for input selection
Press to select HDMI signal terminals in HDMI 1 to HDMI 4.
Press to select component or RGB signal terminal in COMPONENT/RGB IN.
Press to select PC signal terminal in PC IN.
Press to select Input terminal in Terminal Board.
For dual input Terminal Board, you can select either input terminal
using A or B button.
Notes:
• Selecting is also possible by pressing the INPUT button on the
unit.
• Select to match the signals from the source connected to the
component/RGB input terminals. (see page 41)
• Image retention (image lag) may occur on the plasma display
panel when a still picture is kept on the panel for an extended
period. The function that darkens the screen slightly is activated
to prevent image retention (see page 60), but this function is not
the perfect solution to image retention.
16
ENTER/
MENU
INPUT
Basic Controls
Main Unit
Right side
surface
ENTER/
Enter / Aspect button
(see page 19, 24)
Up / Down button
When the menu screen is displayed:
“▲” : press to move the cursor up
“▼” : press to move the cursor down
(see page 24)
MENU
Infrared transmitter for 3D
Eyewear
Note:
Do not place any objects
between the transmitter and
3D Eyewear.
Remote control sensor
Power Indicator
The Power Indicator will light.
• Power-OFF ...... Indicator not illuminated
(The unit will still consume
some power as long as the
power cord is still inserted
into the wall outlet.)
• Standby ........... Red
Orange (When “Control I/F
Select” is set to “LAN”. See
page 52)
• Power-ON ........ Green
• PC Power management (DPMS)
................... Orange (With PC input signal.
See page 43)
INPUT
MENU Screen ON / OFF
Each time the MENU button is pressed, the
menu screen will switch. (see page 24)
Normal Viewing
Picture
Sound
Pos. /Size
Setup
INPUT button
(INPUT signal selection)
(see page 16)
Main Power On / Off Switch
17
Basic Controls
Remote Control Transmitter
Standby (ON / OFF) button
The Plasma Display must first be plugged
into the wall outlet and turned on at the power
switch (see page 14).
Press this button to turn the Plasma Display
On, from Standby mode. Press it again to turn
the Plasma Display Off to Standby mode.
PC button
Press to select PC input. (see page
16)
COMPO. button
Press to select Component or RGB
input. (see page 16)
LIGHT button
The remote control’s buttons illuminate.
MENU button
Displays menu screen. (see page 24)
AUTO SETUP button
Automatically adjusts the position/ size of
the screen. (see page 26)
HDMI buttons
Press to select HDMI 1 to HDMI 4 input.
(see page 16)
PICTURE button
(see page 28)
OK button
Press to make selections.
Cursor buttons
INPUT button
Press to select input signal sequentially.
(see page 16)
RECALL button
Press the “RECALL” button to display
the current system status.
1 Input label
2 Aspect mode (see page 19)
During 3D images (see page 44)
Profile name (see page 36)
NANODRIFT Saver operating
(see page 49)
3 Off timer
The off timer indicator is displayed
only when the off timer has been set.
1
PC
4:3
Memory name: MEMORY2
NANODRIFT
Off timer
90
2
3
ASPECT button
Press to adjust the aspect. (see page 19)
Numeric buttons
(see page 36)
MEM. LOAD button
(see page 36)
18
RETURN button (see page 24)
Press the RETURN button to return to
previous menu screen.
FUNCTION buttons
(see page 54)
EXIT button
Exits from Menu screen.
SLOT buttons
Press to select SLOT Terminal Board.
(see page 16)
3D
POS. /SIZE button
(see page 25)
VIDEO MENU button
Press to select Picture Mode.
(see page 29)
Normal
Monitor
Dynamic
Cinema
EX.SCALER button
(see page 42)
OFF TIMER button
The Plasma Display can be preset
to switch to stand-by after a fixed
period. The setting changes to 30
minutes, 60 minutes, 90 minutes
and 0 minutes (off timer cancelled)
each time the button is pressed.
30
60
90
0
When three minutes remain, “Off timer
3” will flash.
The off timer is cancelled if a power
interruption occurs.
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema
format picture.
Note:
Be aware that if you put the display in a public place for commercial purposes or a public showing
and then use the aspect mode select function to shrink or expand the picture, you may be violating
the copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other
people for commercial purposes without the prior permission of the copyright holder.
Press repeatedly to move through the aspect options:
For details about the aspect mode, please see “List of Aspect Modes” (page 61).
[from the unit]
Right side surface
ENTER/
The aspect mode changes each time the ENTER button is pressed.
For VIDEO (S VIDEO) signal input:
4:3
Zoom1
For PC signal input:
4:3
Zoom
Zoom2
16:9
Zoom3
16:9
14:9
Just
For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):
4:3
Zoom1
Zoom2
Zoom3
16:9
14:9
Just
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i,
750 (720) / 60p • 50p]:
4:3
Just
4:3 Full
14:9
Zoom1
16:9
Zoom2
Zoom3
[For 3D images]
The aspect is fixed as “16:9” and you cannot switch.
Notes:
• The aspect mode is memorized separately for each input terminal.
• Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image
retention to remain on the Plasma Display Panel.
All Aspect mode
Set “All Aspect” to “On” in Options menu to enable the extended aspect mode (page 53). When All Aspect mode, the aspect
mode of pictures is switched as follows. For details about the aspect mode, please see “List of Aspect Modes”. (page 61)
For VIDEO (S VIDEO) signal input:
4:3
Zoom1
For PC signal input:
4:3
Zoom
Zoom2
16:9
Zoom3
16:9
14:9
Just
For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):
4:3
Zoom1
Zoom2
Zoom3
16:9
14:9
Just
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:
4:3 Full
Zoom1
Zoom2
Zoom3
16:9
14:9
Just1
Just2
4:3 (1)
4:3 (2)
19
Viewing 3D images
You can enjoy viewing 3D images with contents or programmes corresponding to the 3D effect by wearing the
3D Eyewear (supplied).
This display supports “Frame Sequential*1”, “Side by Side*2” and “Top and Bottom*3” 3D formats.
*1: The 3D format that the images for the left and right eyes are recorded with the high definition quality and alternately played back
*2, *3: Other available 3D formats
3D Eyewear
3D Eyewear set
3D Eyewear
Nose pad A
Specialised band
Nose pad B
3D Eyewear case
• Use either nose pad A or B for your preference.
• 3D Eyewear can be worn over vision correction glasses.
■Part names and functions
Battery cover
When using for the first time, remove the insulating sheet.
Pull the insulating sheet
Insulating sheet
• To replace the battery “Replacing the battery” (see page 21)
Infrared receiver
Receives infrared signals from the display.
• 3D Eyewear is controlled by receiving infrared signals from the display, which allows you to
view 3D images.
Note:
Do not soil the infrared receiver section or attach stickers etc. to it.
Nose pad installation section
If required, attach the nose pad.
• To attach the nose pad “Attaching the nose pad” (see page 21)
Lenses - Liquid Crystal Shutter
Controls the images for 3D viewing.
• The left and right liquid crystal shutters are
alternately opened and closed in time with
the images on the display screen to achieve
the 3D effect.
Note:
Do not apply pressure to or scratch the
surface of the liquid crystal shutter.
20
Specialised band attaching parts
If required, attach the specialised band.
• To attach the band
“Attaching the specialised band” (see page 21)
Power button of the 3D Eyewear
(bottom side of the 3D Eyewear)
Switches the 3D Eyewear on or off.
• Press the button for about 1 second to turn the power on. The
indicator lamp lights for about 2 seconds and then goes off.
• To turn the power off, press the button for about 1 second again.
The indicator lamp flashes 3 times, then the 3D Eyewear turns off.
Power button
Indicator lamp
Note:
If the 3D Eyewear does not receive any signals from the display for
about 5 minutes, the 3D Eyewear will be turned off automatically.
Viewing 3D images
■Replacing the battery
When the battery is running low, the indicator lamp flashes 5 times on turning the 3D Eyewear on. In this case,
early battery replacement is recommended.
• Dispose of the old batteries as non-burnable rubbish, or in line with the waste disposal regulations in your local
area.
Loosen the screw and remove the battery cover using the supplied screwdriver
Screwdriver (supplied)
Battery cover
Replace the battery
• Use the specified type of battery (coin-shaped lithium battery CR2032).
• Note the correct polarity (+ or -).
Replace and fasten the battery cover
• Make sure that the screw is tightened.
Battery cover
■Attaching the nose pad
Use either nose pad A or B for your preference.
• If you put the 3D Eyewear on vision correction glasses, the nose pad is recommended to be removed.
• You can select the positions of the nose pad A from the 2 levels
Nose pad A of height. Use upper 2 protrusions or lower 2 protrusions on the
3D Eyewear to attach the nose pad A.
or
• Use all 3 protrusions on the 3D Eyewear to attach the nose pad B.
Nose pad B
■Attaching the specialised band
If the 3D Eyewear slips out of place, use the supplied specialised band to hold it in place.
• Attach the band to the left and right tips of the frame, and adjust the length.
Specialised band
Frame
Push to adjust the
length of the band
When the end of the specialised band is straightened, form a loop at the end of the band, and fix the twisted
part.
Fix the
twisted part
• Treat the rubber part carefully not to break it.
■Storing and cleaning the 3D Eyewear
• Use the supplied 3D Eyewear case to store the 3D Eyewear.
• Avoid storing the 3D Eyewear in hot or highly humid locations.
• Use a clean, soft and dry cloth to wipe the 3D Eyewear. Otherwise, dirt or dust may scratch the eyewear.
• Do not use benzene, thinner, or wax on the 3D Eyewear, as doing so may cause the paint to peel off.
• Do not submerge the 3D Eyewear in liquid such as water when cleaning.
21
Viewing 3D images
To view the 3D images
To view the contents of the Frame Sequential format (ex. 3D-compatible Blu-ray Disc, etc.) with 3D effect
Connect the 3D-compatible player via an HDMI cable (see page 11) and playback the contents.
• Use fully wired HDMI compliant cable.
• For the settings of the player, read the manual of the player.
• If you use the non 3D-compatible player, the images will be displayed without 3D effect.
To view the contents of 3D formats other than Frame Sequential with 3D effect.
Match the picture format in “3D Picture Format” (see page 44) before viewing.
• You can view “Side by Side” and “Top and Bottom” with 3D effect even if you use the non 3D-compatible player.
• Please consult the suppliers of contents or programmes for availability of this service.
Turn the 3D Eyewear on
• Press the power button on the 3D Eyewear for about 1 second. (see page 20)
Put on the 3D Eyewear
• If the 3D Eyewear slips out of place, hold it in place using the specialised band, and adjust the length of the
band. (see page 21)
Watch the 3D images
■To turn the 3D Eyewear off
After using the 3D Eyewear, press the power button on the 3D Eyewear for about 1 second to turn it off. (see
page 20)
Notes:
• If the room is lit by fluorescent lights (50 Hz) and light appears to flicker when using the 3D Eyewear, switch off the
fluorescent light.
• 3D content will not be correctly visible if the 3D Eyewear is worn upside down or back-to-front.
• Do not wear the 3D Eyewear when watching anything other than 3D images. Liquid crystal displays (such as
computer screens, digital clocks or calculators, etc.) may be difficult to see while wearing the 3D Eyewear.
• Do not use the 3D Eyewear as sunglasses.
• 3D effects may be perceived differently depending on the person.
22
Viewing 3D images
Troubleshooting for 3D Eyewear
Symptoms
Checks
Cannot see 3D images
3D Eyewear is turned off automatically
There is something wrong with the 3D
images
The indicator lamp does not light when
pressing the power button on the 3D
Eyewear
• Has the 3D Eyewear been switched On?
• Ensure that “3D Picture Display” in “3D Settings” is set to “3D”. (see
page 44)
• Some 3D image signals may not be automatically recognized as
3D images. Set “3D INPUT FORMAT” in “3D Settings” to match the
picture format. (see page 44)
• Check that there are no obstacles between the infrared sensors on
the display and the 3D Eyewear. If the 3D Eyewear stops receiving
the infrared signal for about 5 minutes, the 3D Eyewear will be
turned off automatically.
• Check the available area to use the 3D Eyewear. (see page 22)
• Depending on the person, the 3D images may be difficult to see,
or cannot be seen, especially in users that have a different level of
eyesight between the left and right eyes.
Take the necessary steps (wearing glasses etc.) to correct your
eyesight before use.
• Check that there are no obstacles between the infrared sensors on
the display and the 3D Eyewear or that the 3D Eyewear is placed
inside the coverage area (see page 22). If the 3D Eyewear stops
receiving the infrared signal for about 5 minutes, the 3D Eyewear will
be turned off automatically.
• Check the setting of “3D Picture Sequence”. (see page 44)
• The battery may be running low or flat. Replace it.
• If the indicator lamp does not light after the power button has been
pressed for more than 1 second, the battery may be running low or
flat. Replace it.
Table of images that can be seen for each 3D Picture
Format and the source image format
If the picture appears to be abnormal, refer to the table below to choose the correct 3D picture format setting.
3D Picture Format
Source image
format
Auto
Side by Side
*1
Normal*2
Top and Bottom
Native
Side by side
Top and bottom
*1
Normal format
(2D)
Normal
Normal*2
Normal
When the source image is not recognized correctly
When “3D Picture Display” is set to “3D”, the images will be displayed with 3D effect. When set to “2D”, displayed
without 3D effect.
• Depending on the player or contents, the image may be different from the above illustrations.
*1
*2
23
On-Screen Menu Displays
Remote Control
1 Display the menu screen.
MENU
Press
2 Select the menu.
2
Access
1
Select
Normalise
Picture
Setup
Picture Mode
Pos./Size
Contrast
Sound
Brightness
0
Sharpness
0
Press several times.
Each time the MENU button is pressed,
the menu screen will switch.
Normal Viewing
Picture
Setup
Sound
Pos. /Size
Monitor
White balance
Options
Unit
Warm
Advanced settings
Memory save
Memory load
The menu can be displayed directly by pressing
these buttons. (see page 25, 28)
Memory edit
3 Select the item.
Normalise
Press.
ENTER/
Monitor
Picture Mode
Contrast
25
Brightness
0
Sharpness
5
White balance
Advanced settings
Select.
Select
Warm
(Example: Picture menu)
4 Set.
Press.
ENTER/
Adjust
5 Exit the menu.
Set.
MENU
Press
Press
Press several times.
to return to the previous menu.
Menu display list
Picture menu
Setup menu
Normalise
Picture Mode
Normal
Pos. /Size menu
3D Settings
Normalise
Signal
Auto Setup
Normalise
Contrast
25
Screensaver
H-Pos
0
Brightness
0
0
6
Extended life settings
Input label
H-Size
Colour
V-Pos
0
Hue
0
Network Setup
V-Size
0
Sharpness
5
White balance
Advanced settings
Component/RGB-in select
RGB
Normal
0
Clock Phase
0
0
Clamp Position
Power save
PC Power management
Off
Off
1:1 Pixel Mode
Off
Under scan
Off
Auto power off
Memory load
OSD design
Memory edit
OSD position
Off
Type1
Upper left
English (UK)
see page 41-52
see page 25-27
0
1
see page 40
Off
OSD Language
24
Dot Clock
Balance
Volume
External scaler mode
Memory save
see page 28-39
Sound menu
Adjusting Pos. /Size
1 Display the menu screen.
2 Select “Pos. /Size”.
2
access
1
select
2
adjust
1
select
Picture
Setup
Pos. /Size
Sound
3 Select the item and set.
Normalise
Auto Setup
H-Pos
0
H-Size
0
V-Pos
0
V-Size
0
Dot Clock
0
Clock Phase
0
0
Clamp Position
1:1 Pixel Mode
Off
Under scan
Off
Note:
Unadjustable items are grayed out.
Adjustable items differ depending on the input signal and the display mode.
4 Exit the menu.
To display a menu for adjustment of the Pos. /Size
menu on the bottom of the screen
H-Pos
0
To hide the menu
2
adjust or select
1
select the menu
or
Notes:
• Adjustment details are memorized separately for different input signal formats (Adjustments for component signals are
memorized for 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p · 24sF,
1250 (1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/Digital signals are memorized for each frequency.)
• If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position will shift up or down. This picture
position movement cannot be controlled by the Picture Pos./Size function.
Helpful Hint ( Normalise Normalization)
While the Pos. /Size display is active, if the OK button is pressed during “Normalise”, then all adjustment values
are returned to the factory settings.
25
Adjusting Pos. /Size
● Auto Setup
H-Pos/V-Pos, H-Size/V-Size, Dot Clock and Clock Phase are automatically adjusted when the
RGB or PC signal is received.
This setting is enabled under the following conditions:
• When “Component/RGB-in Select” or “YUV/RGB-in select” in the “Setup” menu (see page 41) is set
to “RGB”, this setting is enabled.
• When the signal is not PC format, this setting is enabled only if “Over scan” (see page 27) is “Off”
or “1:1 Pixel Mode” (see page 27) is “On”, and H-Size/V-Size is not automatically adjusted.
This setting will be invalid and will not work under the following conditions:
• Aspect is set to “Just”
• “Under scan” is set to “On”
Using Remote Control
When
on the remote control is pressed, “Auto Setup” will be executed.
When Auto Setup does not work, “Invalid” is displayed.
Auto mode
When the “Auto Setup“ is set to “Auto” in the Options menu (see page 53), automatic position
adjustment starts:
• When the display power is turned ON.
• When the input signal is switched.
Notes:
• If the dot clock frequency is 162 MHz or higher, Dot Clock and Clock Phase cannot be
made.
• When digital RGB signal input, Dot Clock and Clock Phase cannot be made.
• Auto Setup may not work when a cropped or dark image is input. In such case, switch to
a bright image with borders and other objects are clearly shown, and then try auto setup
again.
• Depending on the signal, out of alignment may occur after Auto Setup. Carry out fine tuning
for the position/size as required.
• If Auto Setup cannot set properly for vertical frequency 60Hz XGA signal (1024×768@60Hz,
1280×768@60Hz, and 1366×768@60Hz), pre-selecting the individual signal in “XGA Mode”
(see page 45) may results in correct Auto Setup.
• Auto Setup does not work well when a signal such as additional information is superimposed
out of valid image period or intervals between synchronizing and image signals are short, or
for image signal with tri-level synchronizing signal added.
• If Auto Setup cannot adjust correctly, select “Normalise” once and press OK button, then
adjust Pos. /Size manually.
● H-Pos
Adjust the horizontal position.
● V-Pos
Adjust the vertical position.
● H-Size
Adjust the horizontal size.
● V-Size
Adjust the vertical size.
● Dot Clock
(During Component, RGB and PC input signal)
Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this
happens, adjust so that any such noise is minimized.
● Clock Phase (During Component, RGB and PC input signal)
Eliminate the flickering and distortion.
26
Adjusting Pos. /Size
● Over scan
Turn image over scan On/Off.
Configurable signals are as follows:
525i, 525p, 625i, 625p, 750/60p, 750/50p (Component Video, RGB, DVI, SDI, HDMI)
On
Off
Notes:
• When “Off” is set, “H-Size” and “V-Size” cannot be adjusted.
• When the “Under scan” is set to “On”, this setting will be invalid.
● Clamp Position (During Component and RGB input signal)
Adjusts the clamp position when black parts of the image have no detail due to underexposure
or are tinged with green.
Optimum value for Clamp Position adjustment
When black parts have no detail due to underexposure (blackout)
→ Value that causes least blackout is the optimum.
When black parts are tinged with green
→ Value that cancels the greenishness without causing blackout is the optimum.
● 1:1 Pixel Mode Adjusts the display size when 1125i, 1125p or 1250i signal is input.
Notes:
• Select On when you would like to replay 1920 × 1080 input signal.
• Applicable input signal;
1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p, 1250 (1080) / 50i
• Select Off when flickering is shown around the image.
• H-Size and V-Size cannot be adjusted when On is selected.
Off
On
● 1:1 Pixel Mode (2k1k) When the input signal is a 2k1k signal (2048 × 1080 / 24p, 2048 × 1080 / 24sF), the
display size is adjusted as follows.
(For 2k1k signals)
Off
On (Left)
On (Center)
On (Right)
Note:
2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed.
● Under scan
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Off
On
Notes:
• “Under scan” can be modified when “Studio mode” in the Options menu is “On”. When
“Studio mode” is “Off”, this setting is “Off” and cannot be changed. (see page 53)
• This setting is valid only when the input signals are as follows;
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p,
1125/24p, 1125/30p, 1125/60p, 1125/50p, 1250/50i (RGB, DVI, SDI, HDMI)
• When “Under scan” is set to “On”, “H-Pos” and “V-Pos” in “Pos. /Size” can be adjusted.
• Refer to each board’s operating instruction for DVI, SDI’s corresponding signals.
27
Picture Adjustments
1 Display the menu screen.
2 Select “Picture”.
2
access
1
select
2
adjust
1
select
Picture
Setup
Pos./Size
Sound
3 Select the item and set.
Normalise
Picture Mode
Normal
Contrast
25
Brightness
0
Colour
6
Hue
0
Sharpness
5
White balance
Note:
Menu that cannot be adjusted is grayout. Adjustable menu changes
depending on signal, input and menu setting.
Normal
Advanced settings
4 Exit the menu.
To display a menu for adjustment of the Picture menu on
the bottom of the screen,
Contrast
25
2
adjust or select
1
select
To display a menu for Advanced settings adjustment, press PICTURE button again.
Black extension
To hide the menu
0
or
Helpful Hint ( Normalise Normalization)
While the “Picture” menu is displayed, if the OK button is pressed during “Normalise”, then all adjustment values
are returned to the factory settings.
28
Picture Adjustments
● Picture Mode
You can switch to the optimal picture mode for the video
source and viewing environment.
Normal
Monitor
Dynamic
Cinema
Normal:
Cinema:
For viewing in standard (evening lighting) environments.
Ideal for movies.
This menu selects the normal levels of Brightness and
Monitor:
Contrast.
For use when creating broadcast or movie content.
Dynamic:
With this picture, even if the overall average picture
For viewing in brighter environments.
level (APL) changes, the brightness of areas with the
This menu selects higher than normal levels of
same signal level does not change.
Brightness and Contrast.
Notes:
• When “Monitor” is selected in Picture Mode, the following menu items cannot be set.
Picture menu: Contrast
Extended life settings: Peak limit (see page 49)
Setup menu: Power save (see page 43)
• If you would like to change the picture and colour of the selected Picture menu to something else, adjust using
the items in the Picture menu. (see below)
● Contrast
Adjusts the proper picture contrast.
● Brightness
Adjusts for easier viewing of dark pictures
such as night scenes and black hair.
● Colour
Adjusts colour saturation.
● Hue
Adjusts for nice skin colour.
● Sharpness
Adjusts picture sharpness.
Less
More
Darker
Brighter
Less
More
Reddish
Greenish
Less
More
● White balance Switches to various screen color tones.
Normal: Intermediate color temperature.
Warm: Colors with a reddish tinge.
Warm2: Colors with a reddish tinge (6100K).
Warm3: Colors with a reddish tinge (5600K).
Studio: Optimal color temperature for studio viewing (3200K).
Cool: Colors with a bluish tinge.
Normal
Cool
Warm
Studio*
Warm2
Warm3
* “Studio” can be modified when
“Studio mode” in the Options menu
is “On”. (see page 53)
Notes:
• You can change the level of each function (Contrast, Brightness, Colour, Hue, Sharpness) for each Picture
Mode.
• The setting details for Normal, Dynamic, Cinema and Monitor respectively are memorized separately for each
input terminal.
• In Contrast, there is not a noticeable change even when contrast is increased with a bright picture or reduced
with a dark picture.
29
Picture Adjustments
Advanced settings
Enables fine picture adjustment at a professional level.
Notes:
• The adjustment values are memorized separately for each input terminal.
• The adjustment range values should be used as an adjustment reference.
Select the item and set.
Advanced settings
Normalise
Picture Mode
Contrast
25
Brightness
0
Colour
6
Hue
0
Sharpness
5
White balance
Normalise
Normal
2
1
access
select
Normal
Advanced settings
Black extension
0
Input level
0
Gamma
W/B High R
0
W/B High G
0
W/B High B
0
W/B Low R
0
W/B Low G
0
W/B Low B
0
2.2
Adjusts the dark shades of the image in gradation.
● Input level
Adjustment of parts which are extremely bright and hard to see.
1.0*
2.0
2.2
1
select
Off
Off
● Black
extension
S Curve
change
Off
Cinema reality
Studio Gain
Noise reduction
Colour Gamut
● Gamma
2
2.6
Less
More
Less
More
Down
Up
Less
More
* When 2k1k signals are received with the Dual Link HD-SDI
Terminal Board (TY-FB11DHD), Gamma “1.0” cannot be
selected.
● “W/B” adjustment
W/B High R
0
W/B High G
0
W/B High B
0
W/B Low R
0
W/B Low G
0
W/B Low B
0
Adjusts the white balance for light red, light
green or light blue areas.
Adjusts the white balance for dark red, dark
green or dark blue areas.
Carry out “W/B” adjustment as follows.
1. Adjust the white balance of the bright sections using the “W/B High R” , “W/B High G” and “W/B High B” settings.
2. Adjust the white balance of the dark sections using the “W/B Low R” , “W/B Low G” and “W/B Low B”
settings.
3. Repeat steps 1 and 2 to adjust.
Steps 1 and 2 affect each other’s settings, so repeat each step in turn to make the adjustment.
30
Picture Adjustments
● Cinema reality When “on”, the display attempts to reproduce a more natural
interpretation of sources such as movie pictures, which
are recorded at 24 frames per second. If the picture is not
stable, turn the setting to “off”.
On
Off
Note:
When “On”, this setting only affects the following signal input:
• 525i (480i), 625i (575i), 1125 (1080) / 60i signal input during “Component” input signal.
● Studio Gain
Sharpens the contrast for a better view when a part of the
image is too light to see.
On
Off
Off: Disables “Studio Gain”.
On: Enables “Studio Gain”.
Notes:
• “Studio Gain” can be modified when “Studio mode” in the Options menu is “On”. When “Studio mode” is “Off”,
this setting is “Off” and cannot be changed. (see page 53)
• This setting is valid only when the input signals are as follows:
Component Video, RGB (analog), SDI, HDMI
● Noise reduction
Sets the following three NR (Noise Reduction) functions together.
P-NR, Block NR, Mosquito NR
Off
Advanced
Min
Max
Mid
[Advanced NR]
Sets the three NR functions separately.
1
2
Select “Advanced”.
Noise reduction
Advanced
P-NR
Off
Block NR
Off
Mosquito NR
Off
select
Select the item and set.
Noise reduction
Advanced
P-NR
Off
Block NR
Off
Mosquito NR
Off
2
set
1
select
Off
Max
Min
Mid
P-NR:
Automatically reduces unwanted picture noise.
Block NR:
Reduces block noise when playing MPEG videos.
Mosquito NR: Reduces mosquito noise around subtitles on MPEG videos.
Note:
“Noise reduction” cannot be adjusted while a PC signal is being applied.
Helpful Hint ( Normalise Normalization)
On the remote control unit, while the “Advanced settings” menu is displayed, if the OK button is pressed during
“Normalise”, then all adjustment values are returned to the factory settings.
31
Picture Adjustments
Colour space adjustment (Colour Gamut)
Changes the colour space to BT.709 signal standard chromaticity point and fine-tunes it.
Advanced settings
Normalise
Black extension
0
Input level
0
Gamma
W/B High R
0
W/B High G
0
W/B High B
0
W/B Low R
0
W/B Low G
0
W/B Low B
0
Cinema reality
Studio Gain
Noise reduction
Colour Gamut
2
access
2.2
Select the item and set.
Colour Gamut
Colour Gamut
1
Native
select
2
change
1
select
Off
Off
Off
● Colour Gamut
DIGITAL CINEMA COLOUR: Sets color gamut to reproduce the original color of movies.
Custom: Enables the colour space adjustment, the colour space adjustment set in the “EDIT” is reflected.
Native: Disables the colour space adjustment, images are displayed in the original colour gamut of the panel.
HDTV Colour: Changes the colour space to BT.709 signal standard chromaticity point.
Notes:
• This setting is memorized separately for each input terminal and “Picture Mode”.
• For 3D images, this setting becomes “Native” and no setting is available.
● Edit
Colour space is fine-tuned.
Notes:
• This setting is valid when “Colour Gamut” is “Custom”.
• This setting is memorized separately for each input terminal and “Picture Mode”.
1
2
Select “Edit”.
2
access
1
select
Select an adjustment
item.
select
3
Change the numerical value.
[To adjust with the ▲▼ button]
Press the
button.
Change the numerical value
with the ▲▼ button.
Press the
button.
4
Press the
button.
Adjustment is ended.
32
Colour Gamut
Colour Gamut
Custom
Edit
R Ratio
G Ratio
B Ratio
R
65535
2110
0
G
2900
65535
1760
Reset
65535
[To input the numerical value directly]
Input the numerical value from
Pressing the
Press the
to
will cancel the value change.
button.
B
0
0
65535
Picture Adjustments
● Reset
Resets the adjustment value of colour space.
Note:
This setting is reflected only for the selected input terminal and the “Picture Mode”.
1
Select “Reset”.
Colour Gamut
Custom
Colour Gamut
2
access
1
select
1
select
2
set
Edit
R Ratio
G Ratio
B Ratio
R
G
B
65535
2110
0
2900
65535
1760
0
0
65535
Reset
2
Select “Ok”.
Colour Gamut
Reset
Ok
Cancel
● Chromaticity diagram
The RGB triangle representing current colour space is shown.
Colour Gamut: Custom
— Native
— Custom
y
x
White line: Colour gamut with “Native” setting (original colour gamut.)
Yellow line: Colour gamut with “Custom” setting (current colour gamut.)
33
Picture Profiles
Up to 16 combinations of picture adjustment values (in the Picture menu and Advanced settings) can be stored in
the display memory as profiles and applied as needed, for a convenient way to enjoy your preferred picture settings.
Note:
If setting items (Picture menu and Advanced settings) are set differently between Memory save and Memory load,
they may not reflect for Memory load.
Normalise
Picture Mode
Contrast
Dynamic
25
Brightness
0
Colour
6
Hue
0
Sharpness
5
White balance
Normal
Advanced settings
Save profiles(page 35)
Load profiles(page 36)
Edit profiles(page 37)
Memory save
Memory load
Memory edit
Normalise
Picture Mode
Cinema
Contrast
25
On
Brightness
0
All Aspect
Off
Colour
6
Auto Setup
Manual
Hue
0
Studio mode
Off
Sharpness
5
3D Emitter
INT
White balance
Onscreen display
Function button assign 1
3D settings
Function button assign 2
Signal
3D Safety Precautions
Memory lock
On
Normal
Advanced settings
Save profiles
Lock profiles(page 38, 39)
Save the picture
adjustment values in the
MEMORY1 profile
Edit the profile
Delete or rename
the profile
MY PICTURE
MEMORY2
MEMORY3
MEMORY4
MEMORY1
MEMORY2
MEMORY3
MEMORY4
Locked profile
MEMORY16
MEMORY16
Load the profile
Custom picture
Original picture
Normalise
Normalise
Normal
Picture Mode
Picture Mode
Cinema
Contrast
0
Contrast
25
Brightness
0
Brightness
0
Colour
0
Colour
6
Hue
0
Hue
0
Sharpness
0
Sharpness
5
White balance
Advanced settings
34
Apply the MEMORY1
profile
Normal
White balance
Advanced settings
Normal
Picture Profiles
Saving profiles
Follow these steps to save picture adjustment values as profiles.
Note:
When the settings are locked in “Extended life settings”, profiles cannot be saved.
1
Specify the picture quality in the Picture menu and
Advanced settings. (see page 28-33)
2
In the Picture menu, select “Memory save”.
2 access
Memory save
5
Memory load
Memory edit
3
1
select
Select a profile name for saving the picture adjustment
values.
2 set
Enter a name for the profile.
[Entering profile names]
Profile names can be up to 40 characters.
To enter text, select characters in the on-screen
keyboard.
Edit the default profile name in the text box as
desired.
1 select
Memory name input
A
N
a
n
0
!
_
Memory save
1. [
2. [
]
MEMORY1
]
MEMORY2
3. [ 1]
]
MEMORY4
4. [
13. [
4
1
select
B
O
b
o
1
”
`
C
P
c
p
2
#
|
MEMORY3
]
MEMORY13
14. [
15. [
]
MEMORY14
]
MEMORY15
16. [
]
MEMORY16
MEMORY1█
D E F
Q R S
d e f
q r s
3 4 5
$ % &
~ < >
Ok
G
T
g
t
6
’
(
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M
Y Z
l m
y z
Space
/ = ?
{
}
,
Cancel
All delete
Delete
@
.
\
;
2
set
ˆ
:
Example: Specifying “MY PICTURE”
Select “All delete”.
1
MEMORY1█
Profiles are labeled with these icons to indicate their
locked status. (see page 36)
[ ], [ ]:Settings can be saved in this profile.
[ ], [ ]:Settings cannot be saved in this profile.
All text is deleted.
To delete individual characters, select “Delete”.
Select “Ok”.
Repeat this process to enter the next character.
Select “M”.
2
M█
Memory save
1
select
2
set
Select “Y”.
3
Save the adjusted value in ”MEMORY1”
Ok
Cancel
MY█
Select “Space”.
4
MY
6
█
When you finished entering the profile name, select
“Ok”.
To cancel saving the profile, select “Cancel”.
1 select
Memory name input
A
N
a
n
0
!
_
B
O
b
o
1
”
`
C
P
c
p
2
#
|
MY PICTURE█
D E F
Q R S
d e f
q r s
3 4 5
$ % &
~ < >
Ok
G
T
g
t
6
’
(
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M
Y Z
l m
y z
Space
/ = ?
{
}
,
Cancel
All delete
Delete
@
.
\
;
2
set
ˆ
:
35
Picture Profiles
Loading profiles
Load profiles and apply the picture adjustment values to the display as follows.
Notes:
• Loaded profiles are stored in memory according to the selected input terminal (see page 16).
• When the settings are locked in “Extended life settings”, profiles cannot be loaded.
<Loading profiles from the Picture menu>
<Loading profiles directly from the remote control>
1
To load profiles 1–9
In the Picture menu, select “Memory load”.
2 access
Memory save
Memory load
Memory edit
2
1
select
Select the profile to load.
1. [ ]
2. [ 1]
12. [ 2]
MEMORY1
MEMORY2
MEMORY12
2
set
1
select
Profiles are labeled with these icons to indicate their
locked status. (see below)
<Loading profiles from
1
2
Press
on the remote control>
1
2
Press a button in the range
.
Select “Ok”.
Memory load
Load from ”MEMORY2”
Ok
1
select
2
set
1
Cancel
To load profiles 10–16
Example: To load profile 16
1
to list the profiles.
Press
.
The profile number is displayed in the upper-right
corner of the screen.
16
Select the profile to load.
1. [ ]
2. [ 1]
12. [ 2]
–
MEMORY1
MEMORY2
MEMORY12
2
set
1
select
2
Select “Ok”.
Memory load
1
select
2
set
Load from ”MEMORY16”
Profiles are labeled with these icons to indicate their
locked status. (see below)
Loading locked profiles…
In the Picture menu, profiles are labeled with these
icons to indicate their locked status.
:Lock1
:Lock2
Normalise
Picture Mode
Dynamic
Contrast
25
Brightness
0
Ok
Cancel
PC
16:9
When profile is being
loaded, profile name is
displayed.
Memory name: MEMORY2
NANODRIFT
Operations with locked profiles are restricted. (see page 38)
Picture adjustment values in the Picture menu cannot be changed, except for the “Picture Mode”. Once you edit the
“Picture Mode” setting, you can edit “Contrast”, “Brightness”, and other picture adjustment values.
Lock1
Picture adjustment values are shown.
Lock2
Picture adjustment values are hidden.
Normalise
Normalise
Picture Mode
Normal
Can be specified.
Picture Mode
Contrast
25
Brightness
0
Brightness
Colour
6
Colour
Hue
0
Sharpness
5
White balance
Advanced settings
36
Cannot be specified.
Normal
Normal
Can be specified.
Contrast
Hue
Sharpness
White balance
Advanced settings
Cannot be specified.
Picture Profiles
Editing profiles
Delete or rename profiles as follows.
<Deleting profiles>
<Renaming profiles>
Note:
Locked profiles and profiles currently in use cannot be
deleted.
Note:
Locked profiles cannot be renamed.
1
In the Picture menu, select “Memory edit”.
2
Memory save
1
In the Picture menu, select “Memory edit”.
Memory save
access
Memory edit
Memory load
Memory edit
2
Memory delete
2
set
1
select
Select the profile to delete.
To delete all profiles, select “All delete”.
1. [
2. [
]
]
MEMORY1
MEMORY2
All delete
4
select
Select “Memory delete”.
Memory name change
3
1
2
set
1
select
2
access
1
select
2
set
1
select
2
set
1
select
Select “Memory name change”.
Memory delete
Memory name change
3
4
Select the profile to rename.
1. [
2. [
]
]
MEMORY2
12. [
]
MEMORY12
MEMORY1
Enter a name for the profile.
Entering profile names
page 35
Select “Ok”.
Memory name input
Memory delete
1
select
2
set
A
N
a
n
0
!
_
Dlete the ”MEMORY1” data.
Ok
2
Memory load
Cancel
5
B
O
b
o
1
”
`
C
P
c
p
2
#
|
█
MEMORY1
D E F
Q R S
d e f
q r s
3 4 5
$ % &
~ < >
Ok
G
T
g
t
6
’
(
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M
Y Z
l m
y z
Space
/ = ?
{
}
,
Cancel
All delete
Delete
@
.
\
;
1
select
2
set
ˆ
:
When you finished entering the profile name, select
“Ok”.
To cancel renaming the profile, select “Cancel”.
Ok
Cancel
1 select
2
set
37
Picture Profiles
Locking profiles
You can lock saved profiles to restrict operations when the profiles are loaded. You can also set passwords.
Notes:
• When the lock is set in “Extended life settings”, profile cannot be locked.
• If profile is locked, the menu operations of “Extended life settings” are restricted. (see page 49)
<Locking and unlocking profiles>
1
2
Display the menu screen.
Select “Options” and hold
more.
access
(3 seconds
or more)
1 select
2
Setup
Pos. /Size
Sound
Select “Memory lock”.
On
All Aspect
Off
Auto Setup
Manual
Studio mode
Off
3D Emitter
5
Select “Ok”.
2
1
Input password
Ok
6
Options
Onscreen display
Enter a 4-digit password.
The default password is
“0123”.
for 3 seconds or
Picture
3
4
access
select
Cancel
1
select
2
set
Select the profile and specify the desired lock
setting.
MEMORY1
Lock1
MEMORY2
Off
MEMORY12
Off
isf Mode
Off
2
1
adjust
select
Change password
INT
Function button assign 1
3D settings
Function button assign 2
Signal
3D Safety Precautions
Memory lock
7
On
Exit the menu.
Once a profile is locked, the following operations are restricted when the profile is loaded.
Setting
Editing the Profile
(Memory edit)
Off (unlocked) Allowed
Lock1
Prohibited
Lock2
Prohibited
Editing Picture Adjustment
Values via the Menu
(Picture menu, Advanced
settings)
Allowed
Prohibited (picture adjustment
values are shown)
Prohibited (picture adjustment
values are hidden)
Saving Picture Adjustment Values
(Memory save)
Allowed
Allowed
Prohibited
<Changing passwords>
1
Follow steps 1–5 in the previous procedure, <Locking
and unlocking profiles>.
2
Select “Change password”.
MEMORY1
Lock1
MEMORY2
Off
MEMORY12
Off
isf Mode
Off
2
access
1
select
3
Enter a new 4-digit password.
4
Select “Ok”.
Change password
Ok
5
Note:
Make a note of the new password to remember it.
38
Input new password
Exit the menu.
Cancel
1
select
2
OK
Picture Profiles
<isf Mode Setting>
Switches to “Picture Mode” mode display.
1
Follow steps 1–5 in the previous procedure,
<Locking and unlocking profiles>.
2
Select “isf Mode”.
MEMORY1
Lock1
MEMORY2
Off
MEMORY12
Off
isf Mode
Off
2
adjust
1
select
Change password
3
4
Specify “On” or “Off”.
Exit the menu.
Specifying “On” for isf Mode changes the “Picture Mode” mode display as follows.
“Picture Mode” mode display
isf Mode: Off
Normal
Dynamic
Cinema
Monitor
Normalise
Picture Mode
Normal
Contrast
25
Brightness
0
Colour
6
Hue
0
Sharpness
5
Mode display when
isf Mode: On
Normal
isf Mode Day
isf Mode Night
Monitor
is selected
isf Mode: Off
Picture Mode
isf Mode: On
Picture Mode
Normal
Normal
Dynamic
isf Mode Day
Cinema
isf Mode Night
Monitor
Monitor
39
Sound Adjustment
1 Display the menu screen.
2 Select “Sound”.
Picture
2
access
1
select
2
adjust
1
select
Setup
Pos. /Size
Sound
3 Select the item and set.
Normalise
Balance
Volume
0
1
4 Exit the menu.
Item
Details
Balance
Adjusts left and right volumes.
Volume
Adjusts the sound volume level.
Helpful Hint ( Normalise Normalisation)
While the “Sound” menu is displayed, if the OK button is pressed during “Normalise”, then all adjustment values
are returned to the factory settings.
SDI Sound Output
This menu is displayed when HD-SDI Terminal Board with audio (TY-FB10HD) or Dual Link HD-SDI Terminal Board
(TY-FB11DHD) is installed to the unit.
SDI Sound Output
2/2
Left Channel
Channel 1
Right Channel
Channel 2
Sound Out
On
Level Meter
Off
Note:
This menu is available only when selecting a
slot that HD-SDI Terminal Board with audio
(TY-FB10HD) or Dual Link HD-SDI Terminal
Board (TY-FB11DHD) is installed.
40
Item
Left Channel
Right Channel
Details
Channel 1 to Channel 16
Selects left audio channel.
Channel 1 to Channel 16
Selects right audio channel.
Sound Out
Off
On
On: Enables audio output.
Off: Disables audio output.
Level Meter
Off
1-8ch
9-16ch
Sets audio channels to show in the audio level meter.
8 channels are displayed in the audio level meter;
4 channels each on both right and left sides of the
display.
Off: Hides the audio level meter.
1-8ch: Displays the audio level meter (1-8ch)
9-16ch: Displays the audio level meter (9-16ch)
Setup menu
1 Display the menu screen.
2 Select “Setup”.
Picture
2
access
1
select
Setup
Pos. /Size
Sound
3 Select the item and set.
3D Settings
Signal
Screensaver
Extended life settings
Input label
2
adjust
1
select
Network Setup
Component/RGB-in select
RGB
External scaler mode
Off
Power save
PC Power management
Off
Off
Auto power off
Off
OSD design
Type1
OSD position
Upper left
OSD Language
English (UK)
4 Exit the menu.
Component / RGB-in select
Component
RGB
Select to match the signals from the source connected to the Component / RGB or PC input terminals.
Y, PB, PR signals
“Component”
RGB signals
“RGB”
Note:
Make setting of the selected input terminal (COMPONENT RGB IN or PC IN).
YUV / RGB-in select
YUV
RGB
Select to match the signals from the source connected to the DVI input terminals.
YUV signals
“YUV”
RGB signals
“RGB”
Notes:
• Selection may not be possible, depending on which optional board is installed.
• Make setting of the selected input terminal (SLOT).
41
Setup menu
External scaler mode
Off
On
This menu can be used to specify whether the built-in scaler or an external scaler is used for scaler functions such
as resizing and picture quality adjustment.
The setting is valid with the following input signals.
1125 (1080) / 24p•25p•30p•50p•60p
Off: Use the built-in scaler.
On: Use an external scaler.
Note:
If “On” is set when other than corresponding signal is input, “Input signal must be 1125p(1080p)”message is
displayed.
Using Remote Control
Each time you press
External scaler mode
, an external scaler is activated or deactivated.
On
Note:
Selecting “On” in this setting deactivates the following settings and disables these operations.
Pos. /Size menu:
H-Size, V-Size, 1:1 Pixel Mode, Display size (see page 26, 27)
Picture menu:
Brightness, Colour, Hue, Sharpness, Memory save, Memory load (see page 29, 35, 36)
Advanced settings: Cinema reality, Noise reduction (see page 31)
Signal menu:
XGA Mode (see page 45)
Options menu:
All Aspect (see page 53)
ASPECT Controls (see page 19)
“EXT. SCALER” is displayed in the menu screen to indicate that an external scaler is in use.
Normalise
EXT.SCALER
Picture Mode
Contrast
Brightness
Colour
Hue
42
Normal
25
Setup menu
Power save
Off
On
When this function is turned On, luminous level of the Plasma Display is suppressed, so power consumption is
reduced.
PC Power management
Off
On
When this function is set to On, it operates under the following conditions to turn the power on or off automatically.
When no pictures (HD/VD sync signals) are detected for 30 or so seconds during PC signal input:
→ Power is turned off (standby); the power indicator lights up orange.
When pictures (HD/VD sync signals) are subsequently detected:
→ Power is turned on; the power indicator lights up green.
Notes:
• This function operates only during PC signal input.
• This function is effective when “Sync” is set to “Auto”, “Component / RGB-in select” is set to “RGB” and during
normal viewing (one picture screen).
Auto power off
On
Off
Equipment power supply is turned Off when there is no signal.
When this is set to On, the power supply of the unit goes Off 10 minutes after the input signals stop.
OSD design
Choose the background color (transparency).
Type1
Type2
Type3
OSD position
Choose the display position.
Each time you press
Display example
or
, the on-screen menu display position changes.
Upper left
Centre
OSD Language
Select your preferred language.
Selectable languages
English(UK)
Deutsch
Français
Italiano
Español
ENGLISH(US)
.......(Chinese)
.......(Japanese)
Русский .......(Russian)
43
Setup menu
3D Settings
If the 3D images are not displayed correctly or seem unusual, please adjust and setup the 3D settings.
Select the item and set.
3D Settings
Signal
Screensaver
2
access
1
select
3D Settings
3D Picture Display
Extended life settings
Input label
Network Setup
Component/RGB-in select
3D Picture Format
3D Picture Sequence
3D
Auto
2
change
Normal
1
select
Safety Precautions
RGB
External scaler mode
Off
Power save
PC Power management
Off
Off
Auto power off
OSD design
OSD position
OSD Language
Off
Type1
Upper left
English (UK)
• 3D Picture Display
3D
2D
3D: Use of 3D Eyewear. You can see 3D images for 3D image signal and 2D images for 2D image signal.
2D: No use of 3D Eyewear. You can see 2D images instead of 3D images.
When set to “3D”, “3D” is displayed during 3D images.
PC
3D
16:9
NANODRIFT
• 3D Picture Format
3D images method is set.
Auto: 3D images are automatically displayed according to the signal.
Side by Side/Top and Bottom: One of the formats of the 3D standard. Select these formats as necessary.
Native: Displays the input signal as it is. Use to identify the format type of the input signal.
• 3D Picture Sequence
Reverse
Normal
This function calibrates the timing to switch the right and left images as well as the timing to switch the shutter of
right and left 3D Eyewear.
Select “Reverse” if you feel that the sense of depth is unusual.
• Safety Precautions
Displays the precautions for viewing 3D images.
44
Setup menu
Signal menu
Note:
“Signal” setup menu displays a different setting condition for each input signal.
Select the item and set.
3D Settings
Signal
Screensaver
2
Extended life settings
Input label
Component/RGB-in select
RGB
External scaler mode
Off
Power save
PC Power management
Off
Off
Auto power off
Off
OSD position
OSD Language
Type1
Upper left
English (UK)
Input signal display
[ AV ]
Signal
3D Y/C Filter (NTSC)
On
Colour system
Auto
For Component
ON
XGA Mode
Auto
H-Freq.
33.7 kHz
V-Freq.
60.0 Hz
Signal Format
1125(1080)/60i
Displays the frequency and the type of
the current input signal.
This display is valid only for
Component / RGB / PC and Digital input signal.
Display range:
Horizontal 15 - 110 kHz
Vertical 48 - 120 Hz
The dot clock frequency is displayed during digital signal input.
1
select
[ RGB ]
Signal
Sync
Auto
1024 ×768
XGA Mode
H-Freq.
33.7 kHz
V-Freq.
60.0 Hz
Signal Format
[ Component ]
Signal
FRAME CREATION
change
For RGB
For Video (S VIDEO)
1 select
Network Setup
OSD design
access
2
1125(1080)/60i
For Digital
(Example: HDMI input)
[ Digital ]
Signal
24p SMOOTH FILM
3D 24p Film Display
Off
60Hz
HDMI Range
Auto
H-Freq.
33.7 kHz
V-Freq.
60.0 Hz
Dot Clock Freq.
Signal Format
108.0 MHz
1125(1080)/60i
• 3D Y/C Filter
This menu is displayed when BNC Dual Video Terminal Board (TY-FB9BD) is installed to the unit.
On
Off
Note:
When On, this setting only affects NTSC input signals.
• Colour system
This menu is displayed when BNC Dual Video Terminal Board (TY-FB9BD) is installed to the unit.
Auto
SECAM
M.NTSC
PAL
NTSC
Set the colour system to match the input signal. When “Auto” is set, Colour system will be automatically selected
from NTSC/PAL/SECAM /M.NTSC.
To display PAL60 signal, select “Auto” or “PAL”.
If the picture image becomes unstable:
With the system set on Auto, under conditions of low level or noisy input signals the image may in rare cases
become unstable. Should this occur, set the system to match the format of the input signal.
• XGA Mode
This menu is displayed when the input signal is analog (Component/PC). This unit supports three types of XGA
signals with 60Hz vertical frequency having different aspect ratios and sampling rates (1,024 × 768 @ 60Hz,
1,280 × 768 @ 60Hz and 1,366 × 768 @ 60Hz).
Auto
1024×768
1280×768
1366×768
Auto: Automatically selected from 1024×768/1280×768/1366×768.
Switch the setting to suit the input signal for better display depends on the angle of view or display resolution
condition.
Note:
After making this setting, be sure to make each adjustment (such as “Auto Setup”) on the “Pos. /Size” menu as
necessary. (see page 25)
45
Setup menu
• Sync
This function operates only during input from PC IN terminal.
Setting RGB sync signal
Confirm that the input is set to RGB input (this setting is valid only for RGB input signal).
Auto: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
on G: Uses a synchronized signal on the Video G signal, which is input from the G connector.
VBS: Uses a synchronized signal of Composite Sync input, which is input from the HD connector.
Setting Component sync signal
Confirm that the input is set to Component input (this setting is valid only for Component input signal).
Auto: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
on Y: Uses a synchronized signal on the Video Y signal, which is input from the Y connector.
Note:
Accepts only RGB signals from COMPONENT/RGB IN terminal with “Sync on G”.
• SDI Through
Set the active through function of the Dual Link HD-SDI Terminal Board (TY-FB11DHD).
Off
On
On: Enables active through.
Off: Disables active through.
Note:
Settings can only be performed for this menu when a slot mounted with a Dual Link HD-SDI Terminal Board
(TY-FB11DHD) is selected.
• FRAME CREATION
Displays reducing screen flicker image for 50Hz/25Hz signal input.
Off
On
Note:
This function activates only for 50Hz/25Hz signal input with 2D images.
• 24p SMOOTH FILM
During 2D or 3D viewing, images captured at 24 frames per second are provided in a smooth manner.
Off
On
Note:
This function can be set only for 24p signal input with 2D or 3D images.
• 3D 24p FILM DISPLAY
For 3D images, images captured at 24 frames per second are set.
60Hz
48Hz
60Hz: Increases the number of frames to reproduce more natural movement images.
48Hz: Reproduces images like film-specific.
Note:
This function can be set only for 24p signal input with 3D images.
• HDMI Range
Switches the dynamic range according to the input signal from HDMI 1 to HDMI 4 terminals.
Video(16-235)
Full(0-255)
Auto
Video(16-235): If the input signal is the video range, Example: HDMI terminal output for DVD player
Full(0-255): If the input signal is full range, Example: HDMI terminal output for personal computer
Auto: Switches the dynamic range automatically between “Video(16-235)” and “Full(0-255)” according to the input signal.
Note:
This function can be set only for HDMI 1 to HDMI 4 terminal input.
46
Setup menu
Screensaver
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a Screensaver should be used.
3D Settings
Signal
Screensaver
Extended life settings
Input label
Network Setup
Component/RGB-in select
2
access
1
select
Screensaver
RGB
External scaler mode
Off
Power save
PC Power management
Off
Off
Auto power off
Start
Negative image
Function
Off
OSD design
Type1
OSD position
Upper left
OSD Language
English (UK)
1 Function selection
Screensaver
Start
Function
Negative image
2
change
1
select
Negative image
White screen
Scrolling bar only
Overlay scrolling bar
Negative image : Negative image will be displayed on the screen.
Scrolling bar only : A white bar will scroll from left to right. The image
won't be displayed.
Overlay scrolling bar : The brightness of the image will be decreased
and a white bar will scroll on it.
White screen : The whole screen will be white.
setting
2 Start
Select “Start”.
Screensaver
2
set
1
select
Start
Function
Negative image
The menu screen will disappear and the Screensaver will be activated. To
stop the Screensaver under On, press any button.
Note: When the display is turned off, the Screensaver will be deactivated.
47
Setup menu
Extended life settings
The following settings are setup to reduce image retention:
Extended life settings
3D Settings
Screensaver
Extended life settings
Input label
Network Setup
2
access
1
select
Component/RGB-in select
RGB
External scaler mode
Off
Power save
PC Power management
Off
Off
Auto power off
Off
OSD design
Type1
OSD position
Upper left
OSD Language
Set to the recommended value
Set individually
Reset to the factory settings
Express settings
Signal
English (UK)
Custom settings
Reset
Extended life settings
Recommended settings
Picture Mode
Contrast
Dynamic
30
Side panel
High
NANODRIFT Saver
Mid
Peak limit
Lock settings
Off
Image Retention Reduction
Menu
Unlock
Apply to current input
Apply to all inputs
Image Retention Reduction Menu
“Extended life settings” enables you to set the following 5 menus (Image Retention Reduction Menu) as recommended
values or set them individually.
Picture Mode
Contrast
“Picture Mode” and “Contrast” are same as “Picture” menu items (see page 29). The settings of this menu will be
reflected to the “Picture” menu.
Side panel
Do not display a picture in 4:3 mode for an extended period,
as this can cause an image retention to remain on the side
panels on either side of the display field.
To reduce the risk of such an image retention, illuminate
the side panels.
This function may be applicable to the non-picture area.
Off:
Low:
Mid:
High:
side panel
4:3 Screen
Display
image
retention
Darken both ends.
Make it dark gray.
Make it gray.
Make it light gray.
Notes:
• To reduce the occurrence of image retention, set the Side panel to High.
• The side panel may flash (alternate black/white) depending on the picture being shown on the screen. Using Cinema
mode will reduce such flashing.
48
Setup menu
NANODRIFT Saver
Moves the display position of the screen slightly to reduce image retention on the display panel.
Low–High: NANODRIFT Saver operates. The display position of the screen moves at set time intervals. You can set
the screen movement range. Some of the screen may appear to be missing as a result of this operation.
If you change the value, a mask is displayed in the range where the picture is missing as a result of
position movement.
When “NANODRIFT” Image Retention Reduction is
operating, “NANODRIFT” is displayed.
PC
16:9
NANODRIFT
Peak limit
On: Suppresses image contrast (peak brightness).
Note: When a still picture is viewed for an extended time, the screen may become slightly darker. (see page 60)
Extended life settings when profile is locked
If profile is locked with “Memory lock” of the Options menu, the operations of this settings menu are
restricted as shown below. “Locking profiles”
page 38
Express settings: Cannot be set.
Custom settings: “Picture Mode”, “Contrast” and “Lock settings” cannot be set.
Reset:
“Picture Mode” and “Contrast” are not reset.
Express settings
Set the “Image Retention Reduction” menu to the recommended settings.
All menus will be locked.
Picture Mode: Normal
Contrast: Recommended setting for each model
Side panel: High
NANODRIFT Saver: Mid
Peak limit: On
1 Select “Express settings”.
Extended life settings
Express settings
2 access
Custom settings
1 select
Reset
2 Select the input to apply the settings.
Extended life settings
Apply to current input
2 set
Apply to all inputs
1 select
3 Select “Yes”.
Extended life settings
Apply to current input
Yes
No
1
select
2
set
49
Setup menu
Custom settings
Set the individual “Image Retention Reduction” menu.
1 Select “Custom settings”.
Extended life settings
2
access
1
select
Express settings
Custom settings
Reset
set each menu to the recommended setting:
2 To
Select “Recommended settings”.
2
Extended life settings
set
Picture Mode
Dynamic
30
Side panel
High
NANODRIFT Saver
Mid
Peak limit
Off
Lock settings
Dynamic
Contrast
1
select
30
0
0
Brightness
Colour
Hue
0
5
Sharpness
White balance
Unlock
Normal
Advanced settings
Apply to current input
Apply to all inputs
Memory save
Memory load
Each menu will be set
as same as the “Express
settings”.
Memory edit
Extended life settings
5 Select the input to apply the settings.
3 Set each menu.
Extended life settings
Extended life settings
adjust
1 select
2
Recommended settings
PICTURE
MENU
Picture
Mode
Dynamic
Contrast
Normalise
Picture Mode
Recommended settings
Contrast
When a menu is locked, it is grayed out and
cannot be set.
“Picture Mode” and “Contrast” will no longer be
able to set in the “Picture” menu, and they are
labeled with icon to indicate their locked status.
Also, “Normalise”, “Memory save” and “Memory
load” are not available.
30
Side panel
High
NANODRIFT Saver
Mid
Peak limit
Off
Lock settings
Picture Mode
Dynamic
Contrast
30
Side panel
High
NANODRIFT Saver
Mid
1
select
1
select
2
set
1
select
2
set
Off
Lock settings
Unlock
Apply to current input
Apply to current input
Apply to all inputs
Apply to all inputs
6 Select “Yes”.
lock each menu setting:
4 To
Set the “Lock settings” to “Lock”.
Extended life settings
Apply to current input
Extended life settings
adjust
1 select
2
Recommended settings
Picture Mode
Dynamic
Contrast
set
Recommended settings
Peak limit
Unlock
2
30
Side panel
High
NANODRIFT Saver
Mid
Peak limit
Yes
No
Off
Lock settings
Unlock
Apply to current input
Apply to all inputs
Reset
Reset the “Image Retention Reduction” menu to the factory settings. Each menu will be unlocked.
1 Select “Reset”.
Extended life settings
2
access
1
select
2
set
1
select
Express settings
2 Select the input to reset the settings.
Extended life settings
Reset current input
Reset all inputs
50
Extended life settings
Reset current input
Custom settings
Reset
3 Select “Yes”.
Yes
No
Setup menu
Customizing the Input labels
This function can change the label of the Input signal to be displayed. (see page 16)
Select an input terminal and set.
3D Settings
Signal
2
Screensaver
Extended life settings
Input label
1
Network Setup
access
select
Component/RGB-in select
RGB
External scaler mode
Off
Power save
PC Power management
Off
Off
Auto power off
OSD design
OSD position
OSD Language
Off
Input label
HDMI1
HDMI1
HDMI2
HDMI3
HDMI4
SLOT INPUT
COMPONENT
PC
HDMI2
HDMI3
HDMI4
SLOT INPUT
COMPONENT
PC
2
change
1
select
Note:
The setting items are the same as the input terminal list of
“Selecting the input signal” (page 16).
Type1
Upper left
English (UK)
The input label changes as follows each time the ◄ or ► button is pressed.
Original
DVD1
(Skip)
DVD2
STB
DVD3
VCR
DVD4
CATV
Blu-ray1
Blu-ray4
Blu-ray2
Blu-ray3
(Skip) : The INPUT button press will skip its input.
51
Setup menu
Network Setup
Make the various settings to use the network function.
3D Settings
DHCP, IP address, Subnet mask and Gateway settings
Signal
1 Set DHCP.
Screensaver
Extended life settings
Input label
When “Off” is selected, IP address and other settings can be set manually.
Network Setup
Component/RGB-in select
RGB
2
access
1
select
2 Select the item and press
3 Enter an address.
IP address
192.168.
I
0.
8
Pressing
Save
Off
IP address
192.168. 0. 8
Subnet mask
255.255.255. 0
Gateway
192.168. 0. 1
Port
1024
LAN Speed
Auto
Network ID
Control I/F Select
MAC address
Use
to select a digit.
Use
to change a number or input the
numerical value from
to
.
3 Press
.
1
2
Network Setup
DHCP
.
4 Select “Save” and press
Port setting
Select “Port” and press
Enter a port number.
1
2
Port
01024
I
0
RS-232C
--:--:--:--:--:--
will cancel the address change.
.
.
Use
to select a digit.
2 Use
to change a number or input the
numerical value from
to
.
3 Press
.
1
Pressing
will cancel the port number change.
Save
Save the current network Setup. Each value set for
DHCP, IP address, Subnet mask, and Gateway will be
saved. If “NG” is displayed, check the same IP address
is not used within the same network.
Port
Set the port number used for command control.
The available setting range is 1024 – 65535.
When the PJLink™ protocol is used, the port setting is
not necessary.
DHCP (DHCP client function)
To obtain an IP address automatically using a DHCP
server, set this to “On”. If DHCP server is not used, set
this to “Off”.
LAN Speed
Set the connection speed of the LAN environment.
Select the value from Auto, 10 Half, 10 Full, 100 Half or
100 Full.
IP address (IP address display and setting)
Enter an IP address if DHCP server is not used.
Network ID
Set the ID to identify this unit.
The available setting range is 0 – 99.
Subnet mask (Subnet mask display and setting)
Enter a subnet mask if DHCP server is not used.
Gateway (Gateway address display and setting)
Enter a gateway address if DHCP server is not used.
Control I/F Select
Set whether to control with RS-232C (serial) or LAN.
When “LAN” is set, power is supplied to LAN circuit,
and power indicator is lit orange under the condition of
power “Off” with remote control (stand-by state).
MAC address
Display the MAC address of this unit. However, the MAC
address is not displayed when the “Control I/F Select” is
set to “RS-232C”.
Notes:
• To use a DHCP server, make sure the DHCP server is started.
• Contact your network administrator for details on settings.
52
Options Adjustments
1
Display the menu screen.
2
3
Select “Options”.
Press
for more than 3 seconds.
Picture
2
access (more
than 3 seconds)
1
select
2
set
1
select
Setup
Pos./Size
Sound
Options
4
Select the item and set.
Onscreen display
On
All Aspect
Off
Auto Setup
Manual
Studio mode
Off
3D Emitter
Function button assign 1
INT
3D settings
Function button assign 2
Signal
3D Safety Precautions
Memory lock
5
On
Exit the menu.
Item
Onscreen display
Adjustments
On: Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
was pressed.
• Remainig time of off-timer after
Off: Hides all the items above from view.
Sets All Aspect mode (advanced aspect setting) or default aspect mode.
With each press of
All Aspect
button, the aspect changes in the selected mode.
Off: Default aspect mode
On: All Aspect mode
Aspect mode of each setting is as follows:
(Example: HD signal)
Off 4:3→4:3 Full→Zoom1→Zoom2→Zoom3→16:9→14:9→Just
On 4:3 (1)→4:3 (2)→4:3 Full→Zoom1→Zoom2→Zoom3→16:9→14:9→Just1→Just2
Sets the operational mode of the automatic position adjustment in the Pos./Size menu.
Manual: Automatic position adjustment starts when
Auto Setup
Auto:
is pressed on the remote control or
automatic position adjustment is executed from the Pos./Size menu.
Other than remote control or menu operation, automatic position adjustment starts:
When the display power is turned ON.
When the input signal is switched.
For switching functions in setting menus used for television studio applications.
Studio mode: On
White balance
Studio mode
Studio Gain
Under scan
Studio mode: Off
“Studio” can be selected.
“Studio” not available.
Cannot be specified
Can be switched On and Off. (set to “Off” and cannot be changed).
Cannot be specified
Can be switched On and Off. (set to “Off” and cannot be changed).
53
Options Adjustments
Item
Adjustments
Set the infrared transmitter for the 3D Eyewear.
INT: Use the infrared transmitter of the unit.
EXT: Use the external 3D IR TRANSMITTER (available separately.)
3D Emitter
Set the function to operate when the FUNCTION button 1 to 2 on the remote control is pressed.
3D settings: The “3D Settings” menu is displayed.
Scrolling bar: The screen saver activates, and after 15 minutes, the display power shuts down
Function button assign 1 (standby).
Function button assign 2 Test patterns: The test pattern is displayed by switching among seven patterns.
Blue only: The screen displays only blue color for image adjustment.
Signal: The “Signal” menu is displayed.
3D Safety Precautions show/hide is set during power ON.
On: 3D Safety Precaution is shown every time when the power is ON.
Off: 3D Safety Precaution is not shown when the power is ON.
When the setting changes from “On” to “Off”, the confirmation screen is displayed as below.
Pressing “YES” switches the setting.
3D Safety Precautions
3D Safety Precautions
If Off is selected, the 3D safety precautions
will not be displayed when power is turned on.
Change Setting?
YES
Memory lock
NO
Locks or unlocks saved profiles. Also for setting passwords. (see page 38)
Using FUNCTION button
Pressing the FUNCTION button activates one of the following five functions. The settings
of functions are performed with the “Function button assign 1” and “Function button assign
2” on the Options menu. (see above)
The factory preset functions are as described below.
FUNCTION 1 Button: 3D Settings
FUNCTION 2 Button: Signal
3D Settings / Signal
The menu screen is displayed.
(Example: 3D Settings)
3D Settings
3D Picture Display
3D
Auto
3D Picture Format
3D Picture Sequence
Normal
Safety Precautions
Pressing the FUNCTION button clears the menu.
Scrolling bar / Test patterns / Blue only
Confirmation screen (Example: Scrolling bar)
Press to select
“Yes”.
Function 1
Scrolling bar
Yes
No
The operation starts.
Press.
Scrolling bar
Test patterns
Activates the “Scrolling bar only” screensaver. After
15 minutes, the display enters standby mode.
Each time you press
(seven in all).
, a different test pattern is displayed
Color Bars
To exit this mode, press any button.
Black
1% window
Red
Green
Frame
(2 lines × 2 dots)
Blue
Blue only
The screen displays only blue color for image
adjustment.
To exit this mode, press any button other than .
To exit this mode, press FUNCTION button.
Note:
“PC Power management” and “Auto power off” are deactivated during “Scrolling bar” or “Test patterns” operation.
(see page 43)
54
Using Network Function
This unit has a network function to control the network connected display with your computer.
Note:
To use the network function, set each “Network Setup” setting and make sure to set the “Control I/F Select” to “LAN”.
(see page 52)
When “LAN” is set, power is supplied to LAN circuit, and power indicator is lit orange under the condition of power
“Off” with remote control (stand-by state).
Example of Network Connection
COMPUTER
Display (main unit, rear)
Less
than
10 cm
LAN cable
(not supplied)
Ferrite core
(supplied)
Ferrite core
(supplied)
Noise cut filter
(supplied)
Installing the Ferrite core
Less
than
10 cm
Open
Hub or broadband router
Pull back the tabs
(in two places)
Wind the cable twice
Press the cable through
and close
Notes:
• Lay the LAN cable away from other connection cables (excluding the power cord).
• Make sure the broadband router or hub supports 10BASE-T/100BASE-TX.
• To connect a device using 100BASE-TX, use “category 5” LAN cable.
• Touching the LAN terminal with a statically charged hand (body) may cause damage due to its discharge.
Do not touch the LAN terminal or a metal part of the LAN cable.
• For instructions on how to connect, consult your network administrator.
Securing the LAN cable (TH-85VX200W)
When using a pedestal (TY-ST85P12) for the installation of the display, use a clamper supplied
with the display to secure the LAN cable. For use with another method of installation, refer to
the corresponding Installation Instructions.
Clamper
Note:
In accordance with the Installation Instructions, secure the LAN cable so that it will not become near the
display unit.
Command Control
Network function of the unit can control the unit in the same way as serial control from a network.
Supported commands
Commands used in the serial control are supported. (see page 13)
Note:
Consult your local Panasonic dealer for detail instructions on command usage.
55
Using Network Function
PJLink™ Protocol
The network function of the unit conforms with PJLink™ class 1 and you can operate the following actions from your
computer using PJLink™ protocol.
• Display setup
• Display status query
Supported commands
Commands to control the unit with PJLink™ protocol are shown in the table below.
Command
Control
POWR
Power control
POWR?
Power status query
INPT
INPT?
AVMT
Input switch
Input switch query
Shutter control
AVMT?
Shutter control query
ERST?
Error status query
LAMP?
INST?
Lamp status query
Input switch list query
NAME?
INF1?
INF2?
INFO?
CLSS?
Projector name query
Manufacturer name query
Model name query
Other information query
Class information query
Remark
Parameter
0 = Standby 1 = Power “On”
Parameter
0 = Standby 1 = Power “On”
Parameter
See the parameter for command INST?
Parameter
10 = Picture On (picture mute deactivated), 11 = Picture Off (picture on mute)
20 = Audio On (audio mute deactivated), 21 = Audio Off (audio on mute)
30 = Shutter mode Off (picture and audio mute deactivated)
31 = Shutter mode On (picture and audio on mute)
Parameter
11 = Picture Off (picture on mute)
21 = Audio Off (audio on mute)
30 = Shutter mode Off (picture and audio mute deactivated)
31 = Shutter mode On (picture and audio on mute)
Parameter
First byte: Means fan error. 0 or 2.
Second byte: 0
Third byte: 0
Fourth byte: 0
Fifth byte: 0
Sixth byte: Means other error. 0 or 2.
Meaning of the 0 – 2 settings:
0 = Error is not detected, 2 = Error
Not supported
Parameter
Numbers 11 to 13 are depending on the slot installation condition
11: PC IN input (PC)
When a single input terminal board When a dual input terminal board is
is attached
attached
11: SLOT input (SLOT INPUT)
11: SLOT input (SLOT INPUT A)
12: PC IN input (PC)
12: SLOT input (SLOT INPUT B)
13: PC IN input (PC)
21: COMPONENT/RGB IN input
(COMPONENT)
31: HDMI 1 input (HDMI1)
32: HDMI 2 input (HDMI2)
33: HDMI 3 input (HDMI3)
34: HDMI 4 input (HDMI4)
Returns empty character (no name information)
Returns “Panasonic”
Returns “TH-103VX200” (for 103-inch model)
Returns version number
Returns “1”
PJLink™ security authentication
Set “Panasonic” for the PJLink™ password.
• PJLink™ is a pending trademark in Japan, the United States, and other countries or areas.
56
Using Web Browser Control
You can use a Web browser to control the unit and set up a network and password.
Before Using Web Browser Control
To use the Web browser control, the unit and computer setups are required.
Unit Setup
Set each “Network Setup” setting and make sure to set the “Control I/F Select” to “LAN”. (see page 52)
Computer Setup
Disable the proxy server settings and enable JavaScript.
(Windows)
Disable proxy server settings
1 Display [Internet Properties] window.
Click [Start] – [Control Panel] – [Network and Internet
Connections] – [Internet Options].
2 Click the [Connections] tab and then [LAN Settings].
3 Deselect the [Use automatic configuration script] and
[Use a proxy server for your LAN] boxes.
4 Click [OK].
Enable JavaScript
1 Display [Internet Properties] window.
Click [Start] – [Control Panel] – [Network and Internet
Connections] – [Internet Options].
2 Set the security level on the [Security] tab to [Default
Level]. Alternatively enable [Active scripting] from the
[Custom Level] button.
(Macintosh)
Disable proxy server settings
1 From the [Safari] menu, click [Preferences].
General screen is displayed.
2 From the [Advanced] tab, click the [Change
Settings…] button next to [Proxies]. Click [Proxies]
and set up a proxy server.
3 Deselect the [Web Proxy] and [Automatic Proxy
Configuration] boxes.
4 Click [Apply Now].
Enable JavaScript
1 Display [Security] of Safari.
2 Select [Enable JavaScript] under [Web content].
Access from Web Browser
Access to the TOP screen of the Web browser control using a Web browser.
1 Start your Web browser.
2 Enter the IP address set with the “Network Setup” of the
unit. (see page 52)
3 Enter the user name and password when the
Authentication screen is displayed.
Authentication screen
Notes:
● The password used here is the same password
used for command control and the PJLink™
security authentication.
● Default user name and password are as follows:
User name: user1
Password: Panasonic
● The password can be changed on the Password
Setup screen after logging in (see page 59). The
user name cannot be changed.
● Under no circumstances, Panasonic Corporation
or it's associated companies will ask customers
their password directly.
Even if you are asked directly, please do not
reveal your password.
4 Click [OK].
After logged in, the TOP screen of the Web browser
control is displayed. (see page 58)
57
Using Web Browser Control
TOP screen structure of the Web browser control
After logging in, the TOP screen of the Web browser control is displayed.
Menu
Menu items are displayed. When a button is clicked,
setup screen of each item is displayed.
Item
BASIC
CONTROL
OPTION
CONTROL
NETWORK
SETTING
CHANGE
PASSWORD
Details
BASIC CONTROL screen is displayed.
(see below)
OPTION CONTROL screen is
displayed. (see below)
Network Setup screen is displayed.
(see page 59)
Password setup screen is displayed.
(see page 59)
According to the selected item from the main menu,
setup status or set items are displayed.
Network ID information
ID to identify the unit is displayed.
Display Control (BASIC CONTROL/OPTION CONTROL Screen)
Click BASIC CONTROL or OPTION CONTROL from the menu. Various controls of the unit can be set.
BASIC CONTROL screen
OPTION CONTROL screen
Click BASIC CONTROL from the menu. Unit status and
buttons to change settings are displayed.
Click OPTION CONTROL from the menu. Command input
field for command control of the unit is displayed.
Item
COMMAND
Item
POWER
Details
Switch ON/OFF of the unit power.
Switch the input signals. Displayed
buttons vary according to the
INPUT SELECT
connection status of the video
device.
AUDIO MUTE Switch ON/OFF of the sound mute.
ASPECT
Switch the screen modes
58
RESPONSE
SEND
Details
Enter a command. Use the same
command used for the serial control.
(see page 13)
Response from the unit is displayed.
Command is sent and run.
Note:
After the settings are changed, it may take a while till
the display status is displayed.
Using Web Browser Control
NETWORK SETTING (Network Setup Screen)
Click NETWORK SETTING from the menu. Various settings of a network can be set. For the details of the setting
items, please check Network Setup under the Set up of the unit. (see page 52)
Item
Notes:
• To use a DHCP server, make sure the DHCP server
is started.
• During a DHCP server is used, IP ADDRESS,
SUBNET MASK, and GATEWAY values cannot be
entered.
• When the set values are changed properly,
“NETWORK SETTING CHANGED.” message and
the changed set items are displayed.
Details
Set to ON when a DHCP server is
DHCP
used, or OFF when it is not used.
IP ADDRESS
Enter an IP address.
SUBNET MASK Enter a subnet mask.
GATEWAY
Enter a gateway address.
Enter the port number used for
PORT
command control. The available
setting range is 1024 - 65535.
Set the connection speed of the LAN
LAN SPEED
environment.
Set the ID to identify this unit. The
NETWORK ID
available setting range is 0 - 99.
SAVE
Save the each set value.
Password Setting (Password Setup Screen)
Click CHANGE PASSWORD from the menu. Password to access the Web browser control can be set. When
the password is changed in this screen, the password used for command control and the PJLink™ security
authentication is also changed.
Item
Notes:
• The default password is “Panasonic”.
• Up to 32 alphanumeric characters can be used for a
password.
• When the password is changed properly, “Password
has changed.” message is displayed.
OLD
PASSWORD
NEW
PASSWORD
Details
Enter the old password.
Enter the new password.
NEW
PASSWORD
(RETYPE)
Enter the password entered in “NEW
PASSWORD” for confirmation.
SAVE
Save the new password. The
confirmation screen is displayed.
Click OK to change the password.
59
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Picture
Sound
Interference
Noisy Sound
Normal Picture
No Sound
No Picture
No Sound
No Picture
Normal Sound
No Colour
Normal Sound
No remote control operations can be performed.
A cracking sound is sometimes heard from the unit.
The top or bottom of the picture on the screen is cut
off when I use the zoom function.
Areas at the top and bottom of the screen where
the image is missing appear when I use the zoom
function.
I can hear sounds coming from inside the unit.
Checks
Electrical Appliances
Cars / Motorcycles
Fluorescent light
Volume
(Check whether the mute function has been activated on the remote control.)
Not plugged into AC outlet
Not switched on
Picture and Brightness/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
If a signal with a non-applicable colour system format, or frequency is input, only
the input terminal indication is displayed.
Colour controls set at minimum level
(see page 28-33)
Colour system (see page 45)
Check whether the batteries have discharged completely and, if they have not,
whether they were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a
strong fluorescent light.
Check whether the remote control designed specifically for use with the unit is
being used. (The unit cannot be operated by any other remote control.)
If there is nothing wrong with the picture or sound, this is the sound of the cabinet
undergoing very slight contractions in response to changes in the room temperature.
There are no adverse effects on the performance or other aspects.
Adjust the position of the picture on the screen.
When using a video software program (such as a cinema size program) with a
screen wider than one in the 16:9 mode, blank areas separate from the images
are formed at the top and bottom of the screen.
When the power is turned on, a sound of the display panel being driven may be
heard: This is normal and not indicative of malfunctioning.
Parts of the unit become hot.
Even when the temperature of parts of the front, top and rear panels has risen, these
temperature rises will not pose any problems in terms of performance or quality.
Power automatically turns off unexpectedly.
Check the settings of “PC Power management” and “Auto power off” in the Setup
menu. Any of them may be set to “On”. (see page 43)
Power indicator is blinking in red.
There is possibility of malfunction. Please contact an Authorized Service
Center.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the
type of input signal. However, this is not a malfunction.
Plasma Display panel
Symptoms
The screen darkens slightly
when bright pictures with minimal
movements are shown.
It takes a while for the picture
to appear.
The edges of the images
flicker.
The brightness on both sides of
images in the 4:3 mode changes.
Some parts of the screen do
not light up.
Image retention appears
Whirring sounds can be heard
from the display unit.
60
Check
The screen will darken slightly when photos, still images of a computer or other pictures with minimal
movements are shown for an extended period. This is done to reduce image retention on the screen
and the shortening of the screen’s service life: It is normal and not indicative of malfunctioning.
The unit digitally processes the various signals in order to reproduce esthetically pleasing images. As such, it
sometimes takes a few moments for the picture to appear when the power has been turned on, when the input
has been switched or when the images for the main picture and sub picture on the two screens are swapped.
Due to the characteristics of the system used to drive the panel, the edges may appear to flicker in
the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
When viewing the side panels at the “High” or “Mid” setting, the brightness on both sides may change
depending on the kind of program shown: This is normal and not indicative of malfunctioning.
The plasma display panel is manufactured using an extremely high level of precision technology,
however, sometimes some parts of the screen may be missing picture elements or have luminous
spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent
image retention to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
Note:
The permanent image retention on the Plasma Display resulting from fixed image use is not an
operating defect and as such is not covered by the Warranty.
This product is not designed to display fixed images for extended periods of time.
The display unit is fitted with a cooling fan to dissipate heat generated during normal use. The whirring
sound is caused by rotation of the fan and is not a malfunction.
List of Aspect Modes
Aspect mode
All Aspect: Factory setting
On
All Aspect: Off
16:9
14:9
16:9
Just
–
The pictures with a 4:3 aspect ratio among the 16:9 aspect
ratio signals are enlarged horizontally so that the picture
distortion is minimized. The left and right edges of the
pictures are cut off. The display of the areas around the
left and right edges of the screen is slightly elongated.
4:3
4:3 (1)
–
4:3 Full
The pictures with a 4:3 aspect ratio among the 16:9
aspect ratio signals are enlarged horizontally so that
their display fills the screen. The left and right edges of
the pictures are cut off.
Zoom1
Letterbox pictures with a 16:9 aspect ratio are enlarged
vertically and horizontally so that their display fills the
screen. The top and bottom edges of the pictures are
cut off.
Zoom2
The letterbox pictures with a 2.35:1 aspect ratio among
the 16:9 aspect ratio signals are enlarged vertically and
horizontally so that their display fills the screen. The top
and bottom edges as well as the left and right edges of
the pictures are cut off.
Zoom3
Letterbox pictures with a 2.35:1 aspect ratio are enlarged
vertically and horizontally so that their display fills the
screen vertically and is slightly larger than the screen
horizontally. The top and bottom edges as well as the
left and right edges of the pictures are cut off.
Zoom1
Zoom3
Pictures with a 4:3 aspect ratio are displayed with their
original aspect ratio. Side panels are displayed at the
left and right edges of the screen.
The pictures with a 4:3 aspect ratio among the 16:9
aspect ratio signals are displayed with their original
aspect ratio. The left and right edges of the pictures are
masked with side panels.
Zoom
Zoom2
The display of the pictures fills the screen.
In the case of SD signals, pictures with a 4:3 aspect
ratio are enlarged horizontally, and displayed. This
mode is suited to displaying anamorphic pictures with
a 16:9 aspect ratio.
Pictures with a 4:3 aspect ratio are enlarged horizontally
so that the picture distortion is minimized. The display of
the areas around the left and right edges of the screen
is slightly elongated.
4:3
4:3 Full
Description
14:9
Just1
4:3 (2)
Enlarged screen
Letterbox pictures with a 14:9 aspect ratio are enlarged
vertically and horizontally so that their display fills the
screen vertically and is slightly smaller than the screen
horizontally. The top and bottom edges of the pictures
are cut off. Side panels are displayed at the left and right
edges of the screen.
Just
Just2
Picture
61
Applicable Input Signals
*Mark: Applicable input signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
Signal name
Horizontal frequency
(kHz)
Vertical frequency
(Hz)
525 (480) / 60i
525 (480) / 60p
625 (575) / 50i
625 (576) / 50i
625 (575) / 50p
625 (576) / 50p
750 (720) / 60p
750 (720) / 50p
1,125 (1,080) / 60p
1,125 (1,080) / 60i
1,125 (1,080) / 50p
1,125 (1,080) / 50i
1,125 (1,080) / 24sF
1,125 (1,080) / 30p
1,125 (1,080) / 25p
1,125 (1,080) / 24p
1,250 (1,080) / 50i
2,048 × 1,080 / 24sF ∗7
2,048 × 1,080 / 24p ∗7
640 × 400 @70 Hz
640 × 480 @60 Hz
640 × 480 @72 Hz
640 × 480 @75 Hz
640 × 480 @85 Hz
800 × 600 @56 Hz
800 × 600 @60 Hz
800 × 600 @72 Hz
800 × 600 @75 Hz
800 × 600 @85 Hz
852 × 480 @60 Hz
1,024 × 768 @50 Hz
1,024 × 768 @60 Hz
1,024 × 768 @70 Hz
1,024 × 768 @75 Hz
1,024 × 768 @85 Hz
1,066 × 600 @60 Hz
1,152 × 864 @60 Hz
1,152 × 864 @75 Hz
1,280 × 768 @60 Hz
1,280 × 960 @60 Hz
1,280 × 960 @85 Hz
1,280 × 1,024 @60 Hz
1,280 × 1,024 @75 Hz
1,280 × 1,024 @85 Hz
1,366 × 768 @50 Hz
1,366 × 768 @60 Hz
1,400 × 1,050 @60 Hz
1,600 × 1,200 @60 Hz
1,600 × 1,200 @65 Hz
1,920 × 1,080 @60 Hz
1,920 × 1,200 @60 Hz
Macintosh13” (640 × 480)
Macintosh16” (832 × 624)
Macintosh21” (1,152 × 870)
15.73
31.47
15.63
15.63
31.25
31.25
45.00
37.50
67.50
33.75
56.26
28.13
27.00
33.75
28.13
27.00
31.25
27.00
27.00
31.46
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
31.47
39.55
48.36
56.48
60.02
68.68
37.64
53.70
67.50
47.70
60.00
85.94
63.98
79.98
91.15
39.55
48.36
65.22
75.00
81.25
67.50
74.04
35.00
49.72
68.68
59.94
59.94
50.00
50.00
50.00
50.00
60.00
50.00
60.00
60.00
50.00
50.00
48.00
30.00
25.00
24.00
50.00
48.00
24.00
70.07
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
59.94
50.00
60.00
70.07
75.03
85.00
59.94
60.00
75.00
60.00
60.00
85.00
60.02
75.03
85.02
50.00
60.00
60.00
60.00
65.00
60.00
59.95
66.67
74.54
75.06
COMPONENT /
RGB IN / PC IN
(Dot clock (MHz))
* (13.5)
* (27.0) ∗5
* (13.5)
(74.25)
(74.25)
(148.5)
(74.25)
(148.5)
(74.25)
(74.25)
(74.25)
(74.25)
(74.25)
(74.25)
*
*
*
*
*
*
*
*
*
*
*
(25.17)
(25.18)
(31.5)
(31.5)
(36.0)
(36.0)
(40.0)
(50.0)
(49.5)
(56.25)
(33.54)
*
*
*
*
*
(65.0)
(75.0)
(78.75)
(94.5)
(53.0)
*
*
*
*
*
*
*
(108.0)
(80.14)
(108.0)
(148.5)
(108.0)
(135.0)
(157.5)
*
*
*
* (27.0)
*
*
*
*
*
*
*
*
*
*
*
HDMI 1-4
∗1
∗1
∗1
∗1
∗2
∗1
∗1
∗1
∗3
∗6
*
*
*
*
*
*
*
*
*
*
∗6
*
*
* (86.71)
* (162.0)
* (175.5)
* (148.5)
∗4
* (30.24)
* (57.28)
* (100.0)
∗1: Based on SMPTE 274M standard.
∗2: Based on SMPTE RP211 standard.
∗3: Based on SMPTE 295M standard.
∗4: The input signal is recognized as 1,125 (1,080) / 60p.
∗5: When selected the RGB format and 525p signal input to the PC IN terminal, it is recognized as VGA 60Hz signal.
∗6: When inputted VGA 60Hz format signal from the other than PC IN terminal, it is recognized as 525p signal.
∗7: Based on SMPTE 292M and 372M standards. These signals can be received when the Dual Link HD-SDI Terminal
Board (TY-FB11DHD) is installed.
Note: Signals without above specification may not be displayed properly.
62
Shipping condition
This function allows you to reset the unit to the factory setting.
1
Display the menu screen.
2
Select “Setup”.
Picture
2
access
1
select
1
select
1
select
2
set
1
select
2
set
Setup
Pos. /Size
Sound
3
Select “OSD Language”.
3D Settings
Signal
Screensaver
Extended life settings
Input label
Network Setup
Component/RGB-in select
RGB
External scaler mode
Off
Power save
PC Power management
Off
Off
Auto power off
Off
OSD design
Type1
OSD position
Upper left
OSD Language
English (UK)
4
Press
5
Select “YES”.
for more than 5 seconds.
Reset to factory default.
YES
6
NO
Select “YES” and wait for 10 sec.
All saved data will be erased
CONTINUE?
YES
NO
Note:
Press
to return to Setup menu when confirmation screen is displayed.
[from the unit]
1 Press the MENU button till the Setup menu is displayed.
2 Press the
or
button to select “OSD Language”.
3 Press the ENTER button for more than 5 seconds.
4 Press the
or
button to select “YES”.
5 Press the ENTER button.
6 Press the
or
button to select “YES”.
7 Press the ENTER button and wait for 10 sec.
Executing this function restores all settings and adjustment values in the following menus to the factoryset default values, as shipped.
On-screen menu: Picture, Advanced settings, Setup, Pos. /Size, Sound, Options
Unlocking profiles (Memory lock: Off, Password: 0123)
63
Specifications
TH-85VX200W
Power Source
Power Consumption
Power on
Stand-by condition
Power off condition
Plasma Display panel
Screen size
(No.of pixels)
Operating condition
Temperature
Humidity
Applicable signals
Colour System
Scanning format
PC signals
Connection terminals
LAN
COMPONENT/RGB IN
Y/G
PB/CB/B
PR/CR/R
AUDIO L-R
PC IN
TH-103VX200W
200 - 240 V AC, 50/60 Hz
1,200 W
1,450 W
0.5 W
0.5 W
0.3 W
0.3 W
Drive method : AC type
Drive method : AC type
85-inch, 16:9 aspect ratio
103-inch, 16:9 aspect ratio
1,889 mm (W) × 1,062 mm (H)
2,269 mm (W) × 1,276 mm (H)
× 2,167 mm (diagonal)
× 2,603 mm (diagonal)
2,073,600 (1,920 (W) ×1,080 (H))
[5,760 × 1,080 dots]
0 °C - 40 °C
20 % - 80 %
NTSC, PAL, PAL60, SECAM, Modified NTSC
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 60p · 50i ·
50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i
VGA, SVGA, XGA, SXGA
UXGA ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
RJ45 10BASE-T/100BASE-TX, compatible with PJLink™
RCA Pin jack
RCA Pin jack
RCA Pin jack
RCA Pin jack × 2
High-Density Mini D-sub 15 Pin
VBS (use HD port)
AUDIO
HDMI 1-4
AV IN
SERIAL
3D SHUTTER OUT
AUDIO
L-R
OUT
Dimensions (W × H × D)
Mass (weight)
Stereo mini jack (M3) × 1
TYPE A Connector × 4
HDMI (Version 1.4 with 3D)
External Control Terminal
D-sub 9 Pin
M3 jack × 1, for 3D IR TRANSMITTER
RCA PIN JACK × 2 (L / R)
Output level: Variable (-∞ ― 0 dB)
2,015 mm × 1,195 mm × 99 mm
approx. 117.0 kg net
with sync 1.0 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
0.5 Vrms
Y or G with sync 1.0 Vp-p (75 Ω)
Y or G without sync 0.7 Vp-p (75 Ω)
PB/CB/B: 0.7 Vp-p (75 Ω)
PR/CR/R: 0.7 Vp-p (75 Ω)
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
with picture 1.0 Vp-p (high impedance)
without picture 0.3 Vp-p (high impedance)
0.5 Vrms
RS-232C compatible
[INPUT 1 kHz / 0 dB, 10 kΩ Load]
2,412 mm × 1,419 mm × 129 mm
(141 mm when including protruding portion of
terminals)
approx. 199.0 kg net
Notes:
• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
• This equipment complies with the EMC standards listed below.
EN55022, EN55024, EN61000-3-2, EN61000-3-3.
64
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives
2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your
local municipality, your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
<Software Information for This Product>
This product has software installed partially licensed under the Free BSD LICENSE.
Free BSD LICENSE regulations under the above specifications are as follows:
(These regulations are set by the third party; therefore the original (English) regulations are stated.)
Copyright © 1980, 1986, 1993
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement:
This product includes software developed by the University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Customer’s Record
The model number and serial number of this product can be found on its rear panel. You should note this serial
number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your
purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
Web Site : http://panasonic.net
© Panasonic Corporation 2010
Serial Number
Pursuant to the directive 2004/108/EC, article 9(2)
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany