QuickSpecs
HP 3100 EI Switch Series
Overview
Models
HP 3100-8 V2 EI Switch
HP 3100-16 V2 EI Switch
HP 3100-24 V2 EI Switch
HP 3100-24-PoE v2 EI Switch
HP 3100-48 V2 Switch
JD318B
JD319B
JD320B
JD313B
JG315A
Key features
Comprehensive security control policies
High reliability with improved backup redundancy
Simplified deployment and ease of use
Highly expandable and highly reliable
Diversified management modes and maintenance
Product overview
HP 3100 EI series switches are Layer 2 Ethernet switches designed for enterprise networks demanding high security and
intelligence. They provide 10/100 Mbps downlink and 1000 Mbps uplink Ethernet ports, and serve as access devices for
100 Mbps-to-desktop applications in enterprise networks. In metropolitan area networks or various industry networks, they
connect end users or aggregate client devices with 10/100 Mbps connections, converging at a higher-capacity switch with
1000 Mbps interfaces. Features include advanced Quality of Service (QoS), rate limiting, QinQ (virtual LAN [VLAN]/VPN),
SSHv2, Multicast VLAN Registration (MVR), Virtual Cable Tester (VCT), HGMP V2, GARP VLAN Registration Protocol
(GVRP), access control list (ACL), media access control (MAC)-IP-port binding, Endpoint Admission Defense, voice and
protocol-based VLAN, Internet Group Management Protocol snooping, and Power over Ethernet (PoE).
Features and benefits
Quality of Service (QoS)
Broadcast control: allows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic
Advanced classifier-based QoS: classifies traffic using multiple match criteria based on Layer 2, 3, and 4
information; applies QoS policies such as setting priority level and rate limit to selected traffic on a per-port or perVLAN basis
Powerful QoS feature: supports the following congestion actions: strict priority queuing (SP), weighted round robin
(WRR) queuing, and SP+WRR
Traffic policing: supports Committed Access Rate (CAR) and line rate
Management
Friendly port names: allow assignment of descriptive names to ports
Remote configuration and management: is available through a secure Web browser or a CLI
Manager and operator privilege levels: enable read-only (operator) and read/write (manager) access on CLI and
Web browser management interfaces
Command authorization: leverages HWTACACS to link a custom list of CLI commands to an individual network
administrator's login; also provides an audit trail
Secure Web GUI: provides a secure, easy-to-use graphical interface for configuring the module via HTTPS
Multiple configuration files: can be stored to the flash image
Complete session logging: provides detailed information for problem identification and resolution
SNMPv1, v2c, and v3: facilitate centralized discovery, monitoring, and secure management of networking devices
Remote monitoring (RMON): uses standard SNMP to monitor essential network functions; supports events, alarm,
history, and statistics group plus a private alarm extension group
IEEE 802.1AB Link Layer Discovery Protocol (LLDP): advertises and receives management information from
adjacent devices on a network, facilitating easy mapping by network management applications
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 1
QuickSpecs
HP 3100 EI Switch Series
Overview
Management VLAN: segments traffic to and from management interfaces, including CLI/telnet, a Web browser
interface, and SNMP
Local and Remote Intelligent Mirroring: mirror traffic from a switch port to a local or remote switch port anywhere
on the network; mirror ACL-selected traffic to a local switch port
Device Link Detection Protocol (DLDP): monitors a cable between two switches and shuts down the ports on both
ends if the cable is broken, preventing network problems such as loop
Troubleshooting: ingress and egress port monitoring enable network problem solving; virtual cable tests provide
visibility into cable problems
Stacking capability: single IP address management for a stack of up to 16 switches
Connectivity
NEW IPv6 (on v2 products):
- Telnet v6: to allow IPv6 management
- DNSv6 Client: for IPv6 host management
- SNMPv6: for IPv6 switch management
- DHCPv6 Client: for automatic IPv6 address configuration of a switch
Auto-MDIX: automatically adjusts for straight-through or crossover cables on all 10/100 and 10/100/1000 ports
Flow control: provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations
Gigabit Ethernet uplinks: are dual-personality ports for either 10/100/1000 or mini-GBIC SFP connectivity for
increased connectivity flexibility
IEEE 802.3af Power over Ethernet (PoE): provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered
devices such as IP phones, wireless access points, and security cameras
Ethernet OAM (IEEE 802.3ah): operations, administration and maintenance (OAM) management capability detects
data link layer problems that occurred in the "last mile"; monitors the status of the link between the two devices
Performance
Hardware-based wire-speed access control lists (ACLs): feature-rich ACL implementation (TCAM based) helps
provide high levels of security and ease of administration without impacting network performance
Gigabit Ethernet interface: provides a connection to the network that eliminates the network as a bottleneck
Resiliency and high availability
Separate data and control paths: increase security and performance
External redundant power supply: provides high reliability
Smart link: allows 50 ms failover between links
Spanning Tree/MSTP, RSTP: provides redundant links while preventing network loops
Port trunking: provides higher switch-to-switch throughput and link-level redundancy, with support for standardsbased link aggregation (IEEE 802.3ad); supports up to 13 trunks, each with up to 8 links (ports) per trunk
Device Link Detection Protocol (DLDP): monitors link connectivity and shuts down ports at both ends if
unidirectional traffic is detected, preventing loops in STP-based networks
Layer 2 switching
NEW PVST+ on v2 products: provides greater interoperability
8K MAC addresses: provide access to many Layer 2 devices
VLAN support and tagging: supports the IEEE 802.1Q, with 4,094 simultaneous VLAN IDs; supports port-based
VLANs, MAC-based VLANs, and protocol-based VLANs
GARP VLAN Registration Protocol: allows automatic learning and dynamic assignment of VLANs
IEEE 802.1ad QinQ and Selective QinQ: increase the scalability of an Ethernet network by providing a hierarchical
structure; connect multiple LANs on a high-speed campus or metro network
Gigabit Ethernet port aggregation: allows grouping of ports to increase overall data throughput to a remote device
Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) protocol snooping:
effectively control and manage the flooding of multicast packets in a Layer 2 network
Layer 3 services
Address Resolution Protocol (ARP): determines the MAC address of another IP host in the same subnet
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 2
QuickSpecs
HP 3100 EI Switch Series
Overview
Dynamic Host Configuration Protocol (DHCP): simplifies the management of large IP networks and supports
client and server
Loopback interface address: defines an address in Routing Information Protocol (RIP) and Open Standard Path
First (OSPF), improving diagnostic capability
Security
Access control lists (ACLs): provide IP Layer 2 to Layer 4 traffic filtering; support global ACL, VLAN ACL, and IPv6
ACL
Multiple user authentication methods:
IEEE 802.1X: is an industry-standard method of user authentication using an IEEE 802.1X supplicant on the
client in conjunction with a RADIUS server
Web-based authentication: is similar to IEEE 802.1X and provides a browser-based environment to
authenticate clients that do not support the IEEE 802.1X supplicant
MAC-based authentication: authenticates the client with the RADIUS server based on the client's MAC
address
Identity-driven security and access control:
Per-user ACLs: permits or denies user access to specific network resources based on user identity and time
of day, allowing multiple types of users on the same network to access specific network services without
risking network security or allowing unauthorized access to sensitive data
Automatic VLAN assignment: automatically assigns users to the appropriate VLAN based on their identities
Secure management access: securely encrypts all access methods (CLI, GUI, or MIB) through SSHv2, SSL,
and/or SNMPv3
Secure FTP: allows secure file transfer to and from the switch; protects against unwanted file downloads or
unauthorized copying of a switch configuration file
Guest VLAN: similar to IEEE 802.1X, it provides a browser-based environment to authenticated clients
Endpoint Admission Defense (EAD): provides security policies to users accessing a network
Port security: allows access only to specified MAC addresses, which can be learned or specified by the
administrator
Port isolation: secures and adds privacy, and prevents malicious attackers from obtaining user information
STP BPDU port protection: blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs,
preventing forged BPDU attacks
STP Root Guard: protects the root bridge from malicious attacks or configuration mistakes
DHCP protection: blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Dynamic ARP protection: blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of
network data
IP Source Guard: filters packets on a per-port basis, which prevents illegal packets from being forwarded
RADIUS/HWTACACS: eases switch management security administration by using a password authentication server
Convergence
IEEE 802.1AB Link Layer Discovery Protocol (LLDP): is an automated device discovery protocol that provides
easy mapping of network management applications
LLDP-MED: is a standard extension that automatically configures network devices, including LLDP-capable IP
phones
LLDP-CDP compatibility: receives and recognizes CDP packets from Cisco's IP phones for seamless
interoperation
IEEE 802.3af Power over Ethernet: provides up to 15.4 W per port to PoE-powered devices such as IP phones,
wireless access points, and video cameras
PoE allocations: support multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user specified) to
allocate PoE power for more efficient energy savings
Voice VLAN: automatically assigns VLAN and priority for IP phones, simplifying network configuration and
maintenance
Multicast VLAN: allows multiple VLANs to receive the same IPv4 or IPv6 multicast traffic, lessening network
bandwidth demand by reducing or eliminating multiple streams to each VLAN
IGMP/MLD snooping: effectively controls and manages the flooding of multicast packets in a Layer
2 network
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 3
QuickSpecs
HP 3100 EI Switch Series
Overview
Device support
Cisco prestandard PoE support: detects and provides power to Cisco's prestandard PoE devices such as wireless
LAN access points and IP phones
Flexibility
Designed with no fan: enables quiet operation for deployment in open spaces
Additional information
Green initiative support: provides support for RoHS and WEEE regulations
Green IT and power: uses the latest advances in silicon development and shuts off unused ports to improve power
efficiency
Warranty and support
Lifetime warranty: for as long as you own the product with advance replacement and next-business-day delivery
(available in most countries)†
Electronic and telephone support: limited electronic and telephone support is available from HP; to reach our support
centers, refer to www.hp.com/networking/contact-support; for details on the duration of support provided with your
product purchase, refer to www.hp.com/networking/warrantysummary
Software releases: to find software for your product, refer to www.hp.com/networking/support; for details on the
software releases available with your product purchase, refer to www.hp.com/networking/warrantysummary
† HP warranty includes repair or replacement of hardware for as long as you own the product, with next business day
advance replacement (available in most countries). The disk drive included with HP AllianceOne Advanced Services and
Services zl Modules, HP Threat Management Services zl Module, HP AllianceOne Extended zl Module with Riverbed
Steelhead, HP MSM765zl Mobility Controller and HP Survivable Branch Communication zl Module powered by Microsoft
Lync has a five-year hardware warranty. For details, refer to the Software license and hardware warranty statements at
www.hp.com/networking/warranty.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 4
QuickSpecs
HP 3100 EI Switch Series
Technical Specifications
HP 3100-8 V2 EI Switch (JD318B)
Ports
8 autosensing 10/100 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX);
Duplex: half or full
1 dual-personality port; auto-sensing 10/100/1000Base-T or SFP
1 RJ-45 serial console port
Physical
Dimensions
9.06(w) x 6.3(d) x 1.72(h) in (23.01 x 16 x 4.37 cm) (1U height)
characteristics
Weight
3.97 lb (1.8 kg)
Memory and processor 128 MB SDRAM, 16 MB flash; packet buffer size: 384 KB
Mounting
Requires angle mounting set if rack mounted (not included)
Performance
100 Mb Latency
< 6 µs (64-byte packets)
1000 Mb Latency
< 5µs (64-byte packets)
Throughput
up to 2.6 million pps
Routing/Switching
3.6 Gbps
capacity
Routing table size
16 entries
MAC address table size 8192 entries
Environment
Electrical
characteristics
Safety
Emissions
Management
Services
Operating temperature 32ºF to 113ºF (0ºC to 45ºC)
Operating relative
10% to 90%, noncondensing
humidity
Nonoperating/Storage -40ºF to 158ºF (-40ºC to 70ºC)
temperature
Nonoperating/Storage 5% to 95%, noncondensing
relative humidity
Acoustic
N/A (fanless)
Maximum heat
31 BTU/hr
dissipation
Voltage
100-240 VAC
Maximum power rating9 W
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser ProductsPart 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA
21 CFR Subchapter J; NOM; ROHS Compliance
FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A;
ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN
61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN
61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive
2004/108/EC; FCC (CFR 47, Part 15) Class A
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area,
please contact your local HP sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 5
QuickSpecs
HP 3100 EI Switch Series
Technical Specifications
HP 3100-16 V2 EI Switch (JD319B)
Ports
16 autosensing 10/100 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX);
Duplex: half or full
2 dual-personality ports; auto-sensing 10/100/1000Base-T or SFP
1 RJ-45 serial console port
Physical
Dimensions
14.17(w) x 6.3(d) x 1.72(h) in (35.99 x 16 x 4.37 cm) (1U height)
characteristics
Weight
5.51 lb (2.5 kg)
Memory and processor 128 MB SDRAM, 16 MB flash; packet buffer size: 384 KB
Mounting
Requires angle mounting set if rack mounted (not included)
Performance
100 Mb Latency
< 6 µs (64-byte packets)
1000 Mb Latency
< 5µs (64-byte packets)
Throughput
up to 5.3 million pps
Routing/Switching
7.2 Gbps
capacity
Routing table size
16 entries
MAC address table size 8192 entries
Environment
Operating temperature 32ºF to 113ºF (0ºC to 45ºC)
Electrical
characteristics
Safety
Emissions
Management
Services
Operating relative
10% to 90%, noncondensing
humidity
Nonoperating/Storage -40ºF to 158ºF (-40ºC to 70ºC)
temperature
Nonoperating/Storage 5% to 95%, noncondensing
relative humidity
Acoustic
N/A (fanless)
Maximum heat
41 BTU/hr
dissipation
Voltage
100-240 VAC
Maximum power rating12 W
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser ProductsPart 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA
21 CFR Subchapter J; NOM; ROHS Compliance
FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A;
ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN
61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN
61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive
2004/108/EC; FCC (CFR 47, Part 15) Class A
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area,
please contact your local HP sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 6
QuickSpecs
HP 3100 EI Switch Series
Technical Specifications
HP 3100-24 V2 EI Switch (JD320B)
Ports
24 autosensing 10/100 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX);
Duplex: half
or full
2 dual-personality ports; auto-sensing 10/100/1000BASE-T or SFP
1 RJ-45 serial console port
Physical
Dimensions
17.32(w) x 6.3(d) x 1.72(h) in (43.99 x 16 x 4.37 cm) (1U height)
characteristics
Weight
7.72 lb (3.5 kg)
Memory and processor 128 MB SDRAM, 16 MB flash; packet buffer size: 384 KB
Mounting
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 6 µs (64-byte packets)
10 Gbps Latency
< 5 µs (64-byte packets)
Throughput
up to 6.5 million pps
Routing/Switching
8.8 Gbps
capacity
Routing table size
16 entries
MAC address table size 8192 entries
Environment
Electrical
characteristics
Safety
Emissions
Management
Services
Operating temperature 32ºF to 113ºF (0ºC to 45ºC)
Operating relative
10% to 90%, noncondensing
humidity
Nonoperating/Storage -40ºF to 158ºF (-40ºC to 70ºC)
temperature
Nonoperating/Storage 5% to 95%, noncondensing
relative humidity
Acoustic
N/A (fanless)
Maximum heat
44 BTU/hr
dissipation
Voltage
100-240 VAC
Maximum power rating13 W
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
UL 60950; NOM-019-SCFI Mexico; EN 60950: 2000, ZB and ZC Deviations; IEC 60950: 1999,
Corr Feb 2000, all national deviations; AS/NZS 60950: 2000 Australia, Russian GOST Safety
Approval
FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A;
ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN
61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN
61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive
2004/108/EC; FCC (CFR 47, Part 15) Class A
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Refer to the HP website at www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area,
please contact your local HP sales office.
HP 3100-24-PoE v2 EI Switch (JD313B)
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 7
QuickSpecs
HP 3100 EI Switch Series
Technical Specifications
Ports
24 autosensing 10/100 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3af PoE); Duplex: half or full
2 dual-personality ports; auto-sensing 10/100/1000BASE-T or SFP
1 RJ-45 serial console port
Physical
Dimensions
17.32(w) x 16.54(d) x 1.72(h) in (44 x 42 x 4.36 cm) (1U height)
characteristics
Weight
14.33 lb. (6.5 kg)
Memory and processor 128 MB SDRAM, 16 MB flash; packet buffer size: 384 KB
Mounting
Mounts in an EIA standard 19-in. telco rack or equipment cabinet (hardware included)
Performance
100 Mb Latency
< 6 µs (64-byte packets)
1000 Mb Latency
< 5 µs (64-byte packets)
Throughput
up to 6.5 million pps
Routing/Switching
8.8 Gbps
capacity
MAC address table size 8192 entries
Environment
Operating temperature 32ºF to 113ºF (0ºC to 45ºC)
Operating relative
10% to 90%, noncondensing
humidity
Electrical
characteristics
Safety
Emissions
Management
Services
Nonoperating/Storage -40ºF to 158ºF (-40ºC to 70ºC)
temperature
Nonoperating/Storage 5% to 95%, noncondensing
relative humidity
Acoustic
Low-speed fan: 42.2 dB, High-speed fan: 51.5 dB
Maximum heat
1586 BTU/hr (1673.23 kJ/hr)
dissipation
Voltage
100-240 VAC
DC Voltage
-52 V to -56 VDC
Maximum power rating465 W
PoE power
370 W
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
PoE power is the power supplied by the internal power supply. It is
dependent on the type and quantity of power supplies and may be
supplemented with the use of an external power supply (EPS).
With DC input, the maximum power is 400 W; PoE power is 370 W.
UL 60950-1; CAN/CSA 22.2 No. 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN
60825-2 Safety of Laser Products-Part 2; IEC 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11;
FDA 21 CFR Subchapter J; NOM; ROHS Compliance
FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A;
ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN
61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN
61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive
2004/108/EC; FCC (CFR 47, Part 15) Class A
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area,
please contact your local HP sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 8
QuickSpecs
HP 3100 EI Switch Series
Technical Specifications
HP 3100-48 V2 Switch (JG315A)
Ports
48 RJ-45 autosensing 10/100 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX); Duplex: half or full
2 SFP dual-personality 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
4 SFP fixed Gigabit Ethernet SFP ports
1 RJ-45 serial console port
Physical
Dimensions
17.32(w) x 10.24(d) x 1.72(h) in (43.99 x 26.01 x 4.37 cm) (1U height)
characteristics
Weight
7.72 lb (3.5 kg)
Memory and processor 256 MB SDRAM, 128 MB flash; packet buffer size: 4 MB
Mounting
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included)
Performance
100 Mb Latency
< 6 µs (64-byte packets)
1000 Mb Latency
< 5 µs (64-byte packets)
Throughput
13.1 million pps
Routing/Switching
17.6 Gbps
capacity
Routing table size
32 entries
MAC address table size 32000 entries
Environment
Operating temperature 32ºF to 113ºF (0ºC to 45ºC)
Operating relative
10% to 90%, noncondensing
humidity
Nonoperating/Storage -40ºF to 158ºF (-40ºC to 70ºC)
temperature
Nonoperating/Storage 5% to 95%, noncondensing
relative humidity
Acoustic
Low-speed fan: 43.2 dB, High-speed fan: 50.0 dB
Electrical
Maximum heat
140 BTU/hr
characteristics
dissipation
Voltage
100-240 VAC
Maximum power rating41 W
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
Safety
UL 60950; NOM-019-SCFI Mexico; EN 60950: 2000, ZB and ZC Deviations; IEC 60950: 1999,
Corr Feb 2000, all national deviations; AS/NZS 60950: 2000 Australia, Russian GOST Safety
Approval
Emissions
FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A;
ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN
61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN
61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive
2004/108/EC; FCC (CFR 47, Part 15) Class A
Management
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Services
Refer to the HP website at www.hp.com/networking/services for details on the service-level
descriptins and product numbers. For details about services and response times in your area,
please contact your local HP sales office.
Standards and
General protocols
protocols
IEEE 802.1ad Q-in-Q
(applies to all products in IEEE 802.1ag Service Layer OAM
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 9
QuickSpecs
HP 3100 EI Switch Series
Technical Specifications
series)
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s (MSTP)
IEEE 802.1w Rapid Reconfiguration of Spanning Tree
IEEE 802.1X PAE
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.3af Power over Ethernet
IEEE 802.3i 10BASE-T
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 951 BOOTP
RFC 959 File Transfer Protocol (FTP)
MIBs
IEEE 8021-PAE-MIB
IEEE 8023-LAG-MIB
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2013 SNMPv2 MIB for UDP
RFC 2233 Interface MIB
RFC 2273 SNMP-NOTIFICATION-MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2618 RADIUS Authentication Client MIB
RFC 2620 RADIUS Accounting Client MIB
RFC 2665 Ethernet-Like-MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2819 RMON MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB
RFC 3826 AES for SNMP's USM MIB
RFC 4133 Entity MIB (Version 3)
LLDP-EXT-DOT1-MIB
LLDP-EXT-DOT3-MIB
LLDP-MIB
IPv6
RFC 1881 IPv6 Address Allocation Management (v2 models only)
RFC 1887 IPv6 Unicast Address Allocation Architecture (v2 models only)
RFC 1981 IPv6 Path MTU Discovery (v2 models only)
RFC 2080 RIPng for IPv6 (v2 models only)
RFC 2373 IPv6 Addressing Architecture (v2 models only)
RFC 2375 IPv6 Multicast Address Assignments (v2 models only)
RFC 2460 IPv6 Specification (v2 models only)
RFC 2461 IPv6 Neighbor Discovery (v2 models only)
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 10
QuickSpecs
HP 3100 EI Switch Series
Technical Specifications
RFC 2462 IPv6 Stateless Address Auto-configuration (v2 models only)
RFC 2463 ICMPv6 (v2 models only)
RFC 2464 Transmission of IPv6 over Ethernet Networks (v2 models only)
RFC 2475 IPv6 DiffServ Architecture (v2 models only)
RFC 2893 Transition Mechanisms for IPv6 Hosts and Routers (v2 models only)
RFC 2925 Definitions of Managed Objects for Remote Ping, Traceroute, and Lookup Operations
(Ping only) (v2 models only)
RFC 2925 Remote Operations MIB (Ping only) (v2 models only)
RFC 3056 Connection of IPv6 Domains via IPv4 Clouds (v2 models only)
RFC 3162 RADIUS and IPv6 (v2 models only)
RFC 3306 Unicast-Prefix-based IPv6 Multicast Addresses (v2 models only)
RFC 3307 IPv6 Multicast Address Allocation (v2 models only)
RFC 3315 DHCPv6 (client and relay) (v2 models only)
RFC 3484 Default Address Selection for IPv6 (v2 models only)
RFC 3493 Basic Socket Interface Extensions for IPv6 (v2 models only)
RFC 3513 IPv6 Addressing Architecture (v2 models only)
RFC 3542 Advanced Sockets API for IPv6 (v2 models only)
RFC 3587 IPv6 Global Unicast Address Format (v2 models only)
RFC 3596 DNS Extension for IPv6 (v2 models only)
RFC 4113 MIB for UDP (v2 models only)
RFC 4443 ICMPv6 (v2 models only)
MIBs
IEEE 8021-PAE-MIB
IEEE 8023-LAG-MIB
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2013 SNMPv2 MIB for UDP
RFC 2233 Interface MIB
RFC 2273 SNMP-NOTIFICATION-MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2618 RADIUS Authentication Client MIB
RFC 2620 RADIUS Accounting Client MIB
RFC 2665 Ethernet-Like-MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2819 RMON MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB
RFC 3826 AES for SNMP's USM MIB
RFC 4133 Entity MIB (Version 3)
LLDP-EXT-DOT1-MIB
LLDP-EXT-DOT3-MIB
LLDP-MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events)
ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED)
SNMPv1/v2c/v3
QoS/CoS
IEEE 802.1P (CoS)
RFC 2474 DSCP DiffServ
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 11
QuickSpecs
HP 3100 EI Switch Series
Accessories
HP 3100 EI Switch
Series accessories
Transceivers
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
Cables
HP 3600 Switch SFP Stacking Kit
HP 0.5 m Multimode OM3 LC/LC Optical Cable
HP 1 m Multimode OM3 LC/LC Optical Cable
HP 2 m Multimode OM3 LC/LC Optical Cable
HP 5 m Multimode OM3 LC/LC Optical Cable
HP 15 m Multimode OM3 LC/LC Optical Cable
HP 30 m Multimode OM3 LC/LC Optical Cable
HP 50 m Multimode OM3 LC/LC Optical Cable
HP 0.5 m PremierFlex OM3+ LC/LC Optical Cable
HP 1 m PremierFlex OM3+ LC/LC Optical Cable
HP 2 m PremierFlex OM3+ LC/LC Optical Cable
HP 5 m PremierFlex OM3+ LC/LC Optical Cable
HP 15 m PremierFlex OM3+ LC/LC Optical Cable
HP 30 m PremierFlex OM3+ LC/LC Optical Cable
HP 50 m PremierFlex OM3+ LC/LC Optical Cable
Power Supply
HP RPS 800 Redundant Power Supply
HP RPS 1600 Redundant Power System
HP RPS 1600 1600W AC Power Supply
Mounting Kit
HP 3100/4210-16 Rack Mount Kit
HP 3100/4210-9 Rack Mount Kit
HP 3100/4210-16/-8 PoE Rack Mount Kit
Power cords
HP X290 H2.7 H2.7 1m RPS800 Cable
HP X290 JD5 JD5 2m RPS1600 Cable
HP 3100-24-PoE v2 EI Switch (JD313B)
HP X110 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP 3100-48 V2 Switch (JG315A)
HP X124 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X125 1G SFP RJ45 T Transceiver
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
JD098B
JD099B
JD118B
JD119B
JD089B
JD324B
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
BK837A
BK838A
BK839A
BK840A
BK841A
BK842A
BK843A
JD183A
JG136A
JG137A
JD321A
JD322A
JD323A
JD184A
JD187A
JD102B
JD120B
JD061A
JD062A
JD063B
JD089B
Page 12
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.
HP X120 1G SFP LC BX Ports
10-U Transceiver
(JD098B)
Connectivity
Physical
A small form-factor
pluggable (SFP) Gigabit characteristics
LX-BX10-U transceiver
that provides a full
duplex Gigabit solution
up to 10km on a single
mode cable.
Electrical
characteristics
Cabling
Notes
Services
HP X120 1G SFP LC BX Ports
10-D Transceiver
(JD099B)
Connectivity
Physical
A small form-factor
pluggable (SFP) Gigabit characteristics
LX-BX10-D transceiver
that provides a full
duplex Gigabit solution
up to 10km on a single
mode cable.
Electrical
characteristics
Cabling
Notes
Services
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U);
Duplex: full only
Connector type
LC
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x
1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Maximum distance:
• 10km
Fiber type
Single Mode
TX 1310nm RX 1490nm
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D);
Duplex: full only
Connector type
LC
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x
1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Maximum distance:
• Up to 10km
Fiber type
Single Mode
TX 1490nm RX 1310nm
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 13
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP X120 1G SFP LC SX Ports
Transceiver (JD118B) Connectivity
A small form-factor
pluggable (SFP) Gigabit
SX transceiver that
provides a full-duplex
Gigabit solution up to
550m on a Multimode
fiber.
Physical
characteristics
Electrical
characteristics
Cabling
Services
HP X120 1G SFP LC LX Ports
Transceiver (JD119B) Connectivity
A small form-factor
pluggable (SFP) Gigabig
LX transceiver that
provides a full duplex
Gigabit solution up to
550m on MMF or 10Km
on SMF
Physical
characteristics
Electrical
characteristics
Cabling
Services
1 LC 1000BASE-SX port
Connector type
LC
Wavelength
850 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x
1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Maximum distance:
• FDDI Grade distance = 220m
• OM1 = 275m
• OM2 = 500m
• OM3 = Not Specified by standard
Cable length
up to 550m
Fiber type
Multi Mode
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
1 SFP 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX)
Connector type
LC
Wavelength
1300 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x
1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Cable type:
Either single mode or multimode;
Maximum distance:
• 550m for Multimode
• 10km for Singlemode
Fiber type
Both
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 14
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP 0.5 m Multimode
OM3 LC/LC Optical
Cable (AJ833A)
Cabling
Notes
Services
HP 1 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ834A)
Notes
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with
effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC
for distances of up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125
um fiber optic cable and Ethernet assembly with LC duplex connectors
on one end and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: 600 / 600 meters
@850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber and designed to work in both the 850 and
1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with
effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC
for distances of up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125
um fiber optic cable and Ethernet assembly with LC duplex connectors
on one end and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 15
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
Services
HP 2 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ835A)
Notes
Services
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with
effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC
for distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125
um fiber optic cable and Ethernet assembly with LC duplex connectors
on one end and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 16
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP 5 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ836A)
Notes
Services
HP 15 m Multimode
OM3 LC/LC Optical
Cable (AJ837A)
Cabling
Notes
Cable type:
50/125 µm core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for
distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: This specification defines the detail requirements for a
tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic
cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with
effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC
for distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125
um fiber optic cable and Ethernet assembly with LC duplex connectors
on one end and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 17
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
Services
HP 30 m Multimode
OM3 LC/LC Optical
Cable (AJ838A)
Cabling
Notes
Services
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with
effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC
for distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125
um fiber optic cable and Ethernet assembly with LC duplex connectors
on one end and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 18
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP 50 m Multimode
OM3 LC/LC Optical
Cable (AJ839A)
Cabling
Notes
Services
HP 0.5 m PremierFlex Notes
OM3+ LC/LC Optical
Cable (BK837A)
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with
effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC
for distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125
um fiber optic cable and Ethernet assembly with LC duplex connectors
on one end and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
• Core diameter: 50um ± 3um; Cladding diameter: 125um ± 2um;
Coating diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH)
thermoplastic.
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL OFN FT4, ROHS. Cable also
has a longitudal white stripe that runs the entire length of the cable.
• Insertion Loss: less than 0.5dB @ 850nm with LED source, 0.003dB/m
added for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 19
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP 1 m PremierFlex
OM3+ LC/LC Optical
Cable (BK838A)
Services
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Notes
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
Services
HP 2 m PremierFlex
OM3+ LC/LC Optical
Cable (BK839A)
Notes
Services
• Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH)
thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source,
0.003dB/m added for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH)
thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source,
0.003dB/m added for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 20
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP 5 m PremierFlex
OM3+ LC/LC Optical
Cable (BK840A)
Notes
Services
HP 15 m PremierFlex
OM3+ LC/LC Optical
Cable (BK841A)
Notes
Services
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH)
thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source,
0.003dB/m added for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH)
thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source,
0.003dB/m added for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 21
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP 30 m PremierFlex
OM3+ LC/LC Optical
Cable (BK842A)
Notes
Services
HP 50 m PremierFlex
OM3+ LC/LC Optical
Cable (BK843A)
Notes
Services
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH)
thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source,
0.003dB/m added for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH)
thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source,
0.003dB/m added for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 22
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP RPS1600
Redundant Power
System (JG136A)
Ports
Physical
characteristics
Environment
Electrical
characteristics
Safety
Services
8 redundant power supply ports
Restrictions: two -56V/25A DC(PoE); six -56V/8A DC(non-PoE)
Dimensions
15.63(d) x 17.32(w) x 1.74(h) in. (39.7 x 44 x
4.42 cm)
Weight
14.11 lb. (6.4 kg)
Full configuration
16.75 lb. (7.6 kg)
weight
Operating temperature 14°F to 122°F (-10°C to 50°C)
Operating relative
5% to 95%
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage 5% to 95%
relative humidity
Altitude
up to 13,123 ft. (4 km)
Acoustic
Pressure: 53 dB; ISO 7779, ISO 9296
Voltage
100-120/200-240 VAC
Current
30/60 A
Idle power
38 W
Maximum power rating3550 W
RPS power
3200 W
PoE power
2800 W
RPS
-55 V
PoE
-55 V
Frequency
50/60 Hz
Notes
Idle power is the actual power consumption of
the device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged in,
and all modules populated.
With one RPS1600 Power Supply, the
PRS1600 Redundant Power System can
provide 1600W power output; With two
PRS1600 Power Supplies, the output power is
3200W.
CE Labeled; UL 60950-1; IEC 60950-1; ICES-003; FCC Part 15,
Subpart B; EU RoHS Compliant; EN 60950-1/A11; C-Tick; VCCI Class
A; ROHS Compliance; EN 300386
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 23
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP RPS1600 1600W AC Physical
Power Supply (JG137A) characteristics
Environment
Electrical
characteristics
Services
HP X125 1G SFP LC
LH40 1310nm
Transceiver (JD061A)
Ports
Connectivity
Physical
A small form-factor
characteristics
pluggable SFP Gigabit
LH40 transceiver that
Electrical
provides a full duplex
characteristics
Gigabit solution up to
40km on a single-mode
fiber.
Cabling
Dimensions
8.19(d) x 4.96(w) x 1.63(h) in. (20.8 x 12.6 x
4.15 cm)
Weight
3.02 lb. (1.37 kg)
Operating temperature 14°F to 122°F (-10°C to 50°C)
Operating relative
5% to 95%
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage 5% to 95%
relative humidity
Voltage
100-120/200-240 VAC
Current
15/30 A
Maximum power rating1600 W
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged in,
and all modules populated.
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
1 LC 1000Base-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1310 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x
1.17 cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
Services
40km distance
Fiber type
Single Mode
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 24
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP X120 1G SFP LC
LH40 1550nm
Transceiver (JD062A)
Ports
Connectivity
Physical
A small form-factor
characteristics
pluggable (SFP) Gigabit
LH40 transceiver that
Electrical
provides a full-duplex
Gigabit solution up to 40 characteristics
km on a single mode
fiber.
Cabling
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1550 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x
1.17 cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
Services
HP X125 1G SFP LC
LH70 Transceiver
(JD063B)
Ports
Connectivity
A small form-factor
pluggable (SFP) Gigabit
LH70 transceiver that
provides a full-duplex
Gigabit solution up to
70km on a single-mode
fiber.
Physical
characteristics
Electrical
characteristics
Cabling
Services
40km distance
Fiber type
Single Mode
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1550 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x
1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
• 70km
Fiber type
Single Mode
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 25
QuickSpecs
HP 3100 EI Switch Series
Accessory Product Details
HP X125 1G SFP RJ45 Ports
T Transceiver (JD089B) Connectivity
Physical
A small form factor
pluggable (SFP) Gigabit characteristics
1000Base-T transceiver
that provides a full
duplex Gigabit solution Electrical
up to 100m on a Cat-5+ characteristics
cable.
Cabling
Services
1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T)
Connector type
RJ-45
Dimensions
2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x 1.37 x
1.4 cm)
Full configuration
0.07 lb. (0.03 kg)
weight
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Cable type:
1000BASE-T: Category 5 (5E or better recommended), 100 Ù
differential 4-pair unshielded twisted pair (UTP) or shielded twisted pair
(STP) balanced, complying with IEEE 802.3ab 1000BASE-T;
Maximum distance:
• 100m
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details
about services and response times in your area, please contact your
local HP sales office.
To learn more, visit: www.hp.com/networking
© Copyright 2010-2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to
change without notice. The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP
shall not be liable for technical or editorial errors or omissions contained herein.
Microsoft is a U.S. registered trademark of Microsoft Corporation.
DA - 13848 Worldwide QuickSpecs — Version 11 — 10.25.2012
Page 26