Bluetooth® USB/MP3/WMA DIGITAL MEDIA RECEIVER LECTEUR

FZ502
Bluetooth® USB/MP3/WMA DIGITAL MEDIA RECEIVER
LECTEUR MÉDIA NUMÉRIQUE Bluetooth® USB/MP3/WMA
RECEPTOR DE MEDIOS DIGITALES Bluetooth® USB/MP3/WMA
Contents
English
Thank you for purchasing this Clarion product.
• Please fully read this owner’s manual before operating this equipment.
• Check the contents of the enclosed warranty card and store it in a safe place with this manual.
1
1. FEATURES................................................................................................................................2
Expanding Systems................................................................................................................2
2. PRECAUTIONS.........................................................................................................................2
Front Panel / Generalities.......................................................................................................3
USB Port.................................................................................................................................3
3. CONTROLS...............................................................................................................................3
Operational Panel...................................................................................................................3
Names of Button.....................................................................................................................3
Remote Control (RCX003)......................................................................................................4
Notes of remote control using.................................................................................................4
4. OPERATIONS............................................................................................................................4
Basic Operations.....................................................................................................................4
System Setup..........................................................................................................................5
Audio Setup.............................................................................................................................6
Radio Operations....................................................................................................................6
SiriusXM Satellite Radio Operations.......................................................................................7
HD Radio Operations..............................................................................................................8
iTunes® Tagging......................................................................................................................9
USB Operations....................................................................................................................10
iPod & iPhone Operations.....................................................................................................10
Bluetooth Operations............................................................................................................12
AUX Operations....................................................................................................................13
5. TROUBLE SHOOTING............................................................................................................13
6. ERROR DISPLAYS.................................................................................................................14
7. SPECIFICATIONS...................................................................................................................14
8. INSTALLATION / WIRE CONNECTION GUIDE.....................................................................15
FZ502
1. FEATURES
2. PRECAUTIONS
WARNING
For your safety, the driver should not operate the controls while driving.
Also, while driving, keep the volume to a level at which external sounds can be heard.
1.I f you have parked the car for a long
time in hot or cold weather, wait until the
temperature in the car becomes normal
before operating the unit.
2.Do not open the case, disassemble the unit,
or lubricate the rotating parts.
Expanding Systems
Expanding audio features
4 Channel Amplifier
iPod/iPhone
(Connect via CCA-748)
USB Memory
(Connect via CCA-755)
Portable Player
(Connect via AUX IN Jack)
®
Bluetooth
cellular phone
SiriusXM Connect™
Vehicle Tuner
HD Radio tuner
(THD301) to be
connected
Note:
• The items listed outside of the frames are the commercial products generally sold.
• CCA-748 and CCA-755: Sold by separately.
3.This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, users, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to consult the dealer or an
experienced radio technician for help.
5.The Bluetooth word mark and logos are
owned by the Bluetooth SIG, Inc. and any
use of such marks by Clarion Co.,Ltd. is
under license.
Other trademarks and trade names are
those of their respective owners.
English
Built-in Parrot Bluetooth® Handsfree (HFP) and Audio Streaming (A2DP &
AVRCP)
Compatible with iPod® / iPhone® with Pandora® internet radio App
SiriusXM-Ready™ and HD Radio Ready™ with iTunes® Tagging
6.P andora, the Pandora logo and other
Pandora marks are trademarks or
registered trademarks of Pandora Media,
Inc. or its subsidiaries worldwide.
“If you have any issues with the Pandora application on your mobile phone, please
direct them to pandora-support@pandora.
com.”
7.SiriusXM and all related marks and logos
are trademarks of SiriusXM Radio, Inc. All
rights reserved.
8.H D Radio™, HD Radio Ready™, and
the HD Radio Ready logo are proprietary
trademarks of iBiquity Digital Corporation.
4.“ Made for iPod,” and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specifically to iPod, or
iPhone, respectively, and has been certified
by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards. Please note that the
use of this accessory with iPod or iPhone
may affect wireless performance.
iPhone, iPod and iTunes are trademarks of
Apple Inc., registered in the U.S. and other
countries.
FZ502
2
INFORMATION FOR USERS:
English
Changes or modifications to this product
unapproved by the manufacturer will void the
warranty and will violate fcc approval.
87.9-107.9MHz
Operational Panel
THIS DEVICE COMPLIES WITH DHHS RULES 21 CFR CHAPTER I
SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
CLARION CO.,LTD.
7-2,SHINTOSHIN,CHUO-KU,SAITAMA-SHI,SAITAMA-KEN,JAPAN
HD Radio™, HD Radio Ready™, and the HD Radio Ready logo are proprietary
trademarks of iBiquity Digital Corporation.
Front Panel / Generalities
For a longer service life, be sure to read the
following cautions.
• Do not allow any liquids on the set from
drinks, umbrellas, etc. Doing so may
damage the internal circuitry.
• Do not disassemble or modify the set in
any way. Doing so may result in damage.
• Do not let cigarettes burn the display.
Doing so may damage or deform the
body.
• If a problem should occur, have the set
inspected at your store of purchase.
Cleaning the body
• Use a soft, dry cloth and gently wipe off
the dirt.
• For tough dirt, apply some neutral
detergent diluted in water to a soft cloth,
wipe off the dirt gently, then wipe again
with a dry cloth.
• Do not use benzene, thinner, car cleaner,
etc., as these substances may damage
the body or cause the paint to peel. Also,
leaving rubber or plastic products in
contact with the body for long periods of
time may cause stains.
3
3. CONTROLS
530-1710kHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
FZ502
MANUFACTURED:
URF
FCC ID: AX2FZ502
QDID NO.: B017789
TX-1095B-A
CHINA
PN:127070009679
[MIC]
USB Port
•The USB memory stick may stick out when
inserted,so it may cause danger during
driving. When connect USB memory
stick to the main unit, please use a USB
extension cable (CCA-755).
•T h e U S B m e m o r y s t i c k s m u s t b e
recognized as “USB mass storage class“
to work properly. Some models may not
operate correctly.
When the memorized data is lost or
damaged by any chance, Clarion shall
not be liable for any damage.
When using an USB memory stick, we
recommend that you backup your data
stored on it before using a personal
computer etc.
•Data files may be broken when using USB
memory sticks in the following situation:
When disconnecting the USB memory
stick or turning the power off during
reading data.
When affected static electricity or electric
noise.
Connect/disconnect the USB memory stick
when it is not accessed.
•C onnecting with the computer is not
covered.
[CONTROL]
[RESET]
USB Slot
Names of Button
[CONTROL] Knob
• Power on (press)
• Power off (long press -> rotate and select “POWER OFF“ ->press)
• Adjust volume level (rotate)
• Toggle the audio source (press)
• Preset channel select (up/down)
• ADJUST mode (long press -> rotate and select “ADJUST” -> press)
• BT mode – Terminate call (right) / Dial (press) /Answer (left) / Transfer call (left) /
Redial (up -> press)
• RADIO mode – Select tuner band (up -> long press) / Station select / Station search
• HD RADIO mode – SUB channels select.
• SiriusXM mode – Direct search
• AUX mode – No function.
• USB mode – Search function
• iPod mode – iPod menu
• PANDORA mode – Station select
[ MIC ] Hole
• Internal microphone
AUX IN
Remote Control (RCX003)
[RDM] Button
• Random play
• SiriusXM mode – Tune to alerted station
[
,
] Buttons
• Preset station up / down
• Previous / next track
• Search (long press)
[RPT] Button
• Repeat play
•SiriusXM mode – Add Artist Alert / Add
Song Alert (long press)
•PANDORA mode – Bookmark song /
Artist (long press)
[SCN/PS/AS] Button
• Scan play / Preset scan
• Auto memory store (long press)
•SiriusXM mode – Channel scan (in current
category) / Preset scan (long press)
[BAND/TOP] Button
• MP3/WMA mode – Top play (long press)
• HD RADIO mode – Select tuner band
•SiriusXM mode – Select tuner band,
quit Replay(Replay mode) / Select
category(long press)
• PNADORA mode – Skip song
[ , ] Buttons
• Volume up / down
[
] Button
• Play / Pause
• SirusXM mode – Replay mode
[ISR] Button
• Recall ISR station stored in memory
•Store current station in ISR memory (long
press)
•HD Radio mode – iTunes Tagging (When
connected with HD Radio tuner and
displayed ”DIGITAL” indicator and ”TAG”
indicator on display.)
•SiriusXM mode – iTunes Tagging (When
connected with SiriusXM Vehicle Tuner
and displayed ”TAG” on display)
4. OPERATIONS
Basic Operations
Note:
•Refer to the diagrams in “3. CONTROLS”
when reading this chapter.
CAUTION
[MUTE] Button
• Mute the volume
[1~6] Buttons
• [1] Button: Preset station 1.
• PANDORA mode – Create new station
• [2] Button: Preset station 2.
• [3] Button: Preset station 3.
• [4] Button: Preset station 4.
• [5] Button:Preset station 5.
• PANDORA mode – Thumbs down
• [6] Button: Preset station 6.
• PANDORA mode – Thumbs up
[SRC/ ]
[
,
[ISR]
]
[
[
]
,
]
Turn the [CONTROL] knob on the front
panel.
The adjustable range of volume is 0 to 40.
Power on / off
While driving, keep the volume level at
which external sounds can be heard.
• Start the engine before using this unit.
• Be careful about using this unit for a long
time without running the engine. If you
drain the car’s battery too far, you may not
be able to start the engine and this can
reduce the service life of the battery.
1. Start the engine. The power button / knob
illumination on the unit will light up.
[SCN/
PS/AS]
[BAND/TOP]
Engine ON
position
[RPT]
[SOUND]
[DISP]
[RDM]
[1~6]
[MUTE]
[DISP] Button
• Display switch
Notes of remote control using
Replacing the lithium battery of remote control unit.
When the range of the operation of the card remote control becomes short or no functions
while operating. Replace the battery with a new lithium battery. Make sure the battery polarity
replacement is correct.
1.Pull out the battery holder while pressing the stopper.
2.Insert the button-type battery with the stamped(+) mark facing upward.
CR 2025
Insert the battery holder into the remote control.
(CR 2025)
Volume adjustment
When the unit is turned on, starting and
stopping the engine with its volume
raised to the maximum level may harm
your hearings.
Be careful about adjusting the volume.
Notes:
[SOUND] Button
• Sound effect setting
Note:
Doing the operation above again or adjusting
volume will release muting.
2. Press the [CONTROL] knob on the front
panel or [SRC / ] button on the remote
control to turn on the power under standby
mode. The unit goes back to the last
status after power on.
3. Press and hold the [CONTROL] knob
(center long press) on the front panel,
and rotate the [CONTROL] knob choose
POWER OFF, then press the [CONTROL]
knob on the front panel to turn off the
power.
Or press and hold [SRC / ] button on
remote control to turn off the power.
English
[SRC/ ] Button
• Toggle the audio source
• Power on ( short press) / off (long press)
CAUTION
Playing source selection
Press [CONTROL] knob on the front panel
repeatedly to choose desired playing source.
Note:
• Playing source selection means selecting
work mode, such as RADIO mode and
AUX mode, etc.
Display system time
Press the [DISP] button on the remote
control to switch the display information,
system time and playing source.
RESET
Note:
* When the [RESET] button is pressed,
frequencies of radio stations, titles, etc.
stored in memory are cleared.
You entered ”CODE” is not cleared.
Mute
Press the [MUTE] button on the remote
control to mute the volume from the unit.
RESET
FZ502
4
System Setup
English
At all mode, press and hold [CONTROL] knob
(center long press), and rotate the [CONTROL]
knob choose ADJUST, then press the [CONTROL]
knob to enter system setup. Press [CONTROL]
knob (left / right) to select options, rotate the
[CONTROL] knob to adjust.
DELETE (BT mode)
1. Rotate the [CONTROL] knob to choose
the paired mobile phone name from the
pairing list.
2. Press and hold the [CONTROL] knob to
confirm.
PCH MEMO (RADIO/HD RADIO/SIRIUSXM
mode)
Rotate the [CONTROL] knob to choose
PCH 1 / PCH 2 / PCH 3 / PCH 4 / PCH 5 or
PCH 6, press and hold [CONTROL] knob
(center long press) to store it in the memory.
DISCON (BT mode)
Disconnect currently connected mobile
phone.
1. R otate the [CONTROL] knob, mobile
phone displays are currently connected.
2. Press and hold the [CONTROL] knob to
disconnect.
CLOCK
Press the [CONTROL] knob (right) to
choose minute, and rotate the [CONTROL]
knob to set minute.
Press the [CONTROL] knob (left) to choose
hour, and rotate the [CONTROL] knob to set
hour.
Then long press [CONTROL] knob (center)
to confirm the time setting.
DX/LO (RADIO mode)
Rotate the [CONTROL] knob to choose
radio local or distant at RADIO mode.
•LO: Only stations with strong signal can
be received.
•DX: Stations with strong and weak signals
can be received.
SELECT (BT mode)
This ”SELECT” menu is intended to
automatically paired by selecting a mobile
phone was stored.
This unit can store three mobile phones. The
mobile phone will be stored in paired order
to the unit. The mobile phone can be stored
up to three. The fourth mobile phone can
not be stored. If you want to store a fourth
mobile phone, please delete unwanted
mobile phone from ”DELETE” menu.
1. Rotate the [CONTROL] knob to choose
the pair mobile phone name from the
pairing list.
2. Press and hold the [CONTROL] knob to
confirm.
5
System Setup
FZ502
MIC SEL (BT mode)
Rotate the [CONTROL] knob to choose
microphone EXTERNAL or INTERNAL.
MIC GAIN (BT mode)
Rotate the [CONTROL] knob to choose Mic
gain: -5,-4,-3,-2,-1,0,1,2,3,4,5.
You can change the gain of MIC when a
telephone partner cannot hear your voice.
TONE SEL (BT mode)
You can get mobile phone ring tone from the
speaker.
Rotate the [CONTROL] knob to choose
AUTO or INTERNAL.
• AUTO:
Mobile phone ring tone from the speaker.
• INTERNAL:
The unit original ring tone from the speaker.
AUTO ANS (BT mode)
To answer incoming calls automatically.
Rotate the [CONTROL] knob to choose
AUTO ANS ON or OFF.
AUTO CON (BT mode): ON/OFF
Rotate the [CONTROL] knob to choose
AUTO CON ON or OFF.
PIN CODE
This CODE is required to pairing for
bluetooth.
Press the [CONTROL] knob, rotate the
[CONTROL] knob to select a digit, press
the [CONTROL] knob (left / right) to move
the cursor. Press the [CONTROL] knob to
confirm.
The PIN CODE default setting is “ 0000 “.
PARENTAL PASSWORD (SiriusXM mode)
Change parental password. Original code is
“0000”.
LOCK CH (SiriusXM mode)
Lock the current channel.
UNLOCK CH (SiriusXM mode)
Unlock current locked channel.
UNLOCK ALL CH (SiriusXM mode)
Unlock all parental locked channels.
ALERT: ON/OFF (SiriusXM mode)
Activate interruption by Artist and Song alert.
DELETE ALL ALERT (SiriusXM mode)
Delete saved alert items for artist and song.
AUX SENS (AUX mode)
Rotate the [CONTROL] knob to choose AUX
input sensitivity LOW, MID or HIGH at AUX
mode.
SCRN SVR: ON/OFF
Rotate the [CONTROL] knob to choose
SCRN SVR (screen saver) ON or OFF.
SCROLL: ON/OFF
For track information that is longer than the
display panel:
When SCROLL is ON, the LCD will display
ID3 TAG information cyclely, e.g.: TRACK>FOLDER->FILE->ALBUM->TITLE>ARTIST->TRACK->...
When SCROLL is OFF, the LCD will display
one of the ID3 TAG information, the default
is TRACK, but user can adjust it to other ID3
TAG information by pressing [DISP] button
on the remote control.
DIMMER: ON/OFF
Rotate the [CONTROL] knob to choose
DIMMER ON or OFF.
•ON: LCD dimmer is active when small light
of vehicle is turned ON.
•OFF: LCD always maximum brightness
regardless of the vehicle small light.
REAR/S-W
Rotate the [CONTROL] knob to choose
REAR or S-WOOFER(SUB-WOOFER).
SW PHASE
Rotate the [CONTROL] knob to choose
REVERSE or NORMAL.
BEEP: ON/OFF
Rotate the [CONTROL] knob to choose
button beep sound ON or OFF.
TEL-SW
Rotate the [CONTROL] knob to choose TEL
SW sound ON or OFF.
• MUTE:
The sound from this unit is muted during
telephone calls.
• OFF:
This unit continues normal operation even
when the cellular phone is used.
• ON:
You can listen to your telephone calls from
the speakers connected to this unit.
*When listening to your calls on your car
speakers, you can adjust the volume by
turning the [CONTROL] knob.
BLINKING
Rotate the [CONTROL] knob to choose
BLINKING light ON or OFF.
CODE
Setting the anti-theft function (CATS)
“CATS” is the acronym of “Clarion AntiTheft System”. When you set a PIN code
(called as “Personal Code”), a theft is
prevented by disabling the operation of the
unit at the theft.
Once you set this code, this function will not
be deactivated unless you delete this code.
Press the [CONTROL] knob, rotate the
[CONTROL] knob to select a digit, press
the [CONTROL] knob (left / right) to move
the cursor. Press and hold the [CONTROL]
knob to confirm.
System Setup
The procedure to delete this code is same as
the way of setting the code.
•Write down your Code in case you forget
it.
•If you have lost your Personal Code,
please contact Clarion customer service.
•The CODE screen will be displayed when
turning the ACC power on after performing
the following operations:
• The car battery was replaced.
• The backup power was cut off.
• The RESET button was pressed.
•When you enter a wrong Personal
Code, the message “LOCK - - - -” is
displayed and the Personal Code entry
is prohibited for a while.
PANDORA: ON/OFF
Select OFF if the Pandora application has
not been installed on your iPod touch or
iPhone.
12/24H
Rotate the [CONTROL] knob to choose time
format: 12 or 24 hours.
S-CTRL (iPod mode) : ON/OFF
Rotate the [CONTROL] knob to choose
S-CTRL (Simple control) ON or OFF.
* Refer to P11.
Auto store
Press the [CONTROL] knob or [SRC / ]
button on the remote control to switch to the
RADIO source.
Only stations with sufficient signal strength
will be detected and stored in the memory.
Press and hold the [SCN/PS/AS] button on
the remote control to start automatic station
search.
To stop auto store, press other buttons
having radio functions.
Select one radio band
Press the the [CONTROL] knob (up long
press) on the panel or [BAND/TOP] button
on the remote control to select one radio
band among FM1, FM2, FM3 and AM.
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press [CONTROL] knob (left/right) on the
panel or [ , ] buttons on the remote
control to tune in a higher / lower station.
This prohibited time is changed according to
the number of times of wrong code entry as
follows:
• 1 to 6 times: 15 seconds
• 7 times or more: 15 minutes
Auto tuning
Press and hold [CONTROL] knob (left/right)
on the panel or [ , ] buttons the remote
control to seek a higher / lower station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Audio Setup
SOUND
Press the [CONTROL] knob to choose
SOUND. First press shows current EQ.
Rotate the [CONTROL] knob to choose
BEAT EQ in this order:
OFF -> B-BOOST -> IMPACT -> EXCITE ->
CUSTOM
To change CUSTOM setting, and press
the [CONTROL] knob (center), then press
[CONTROL] knob (right/left) to select EQ
effects including: BASS-G -> BASS-F ->
BASS-Q -> MID-G -> MID-F -> MID-Q
-> TREBLE-G -> TREBLE-F, rotate the
[CONTROL] knob to select a value.
BASS-G / MID-G / TREBLE-G: (-7)- (+7)
BASS-F: 50 / 100 / 200
BASS-Q : 0.7 / 1.0 / 1.4 / 2.0
MID-F: 500 / 1 K / 2 K
Select tuner as playing source
MID-Q: 0.7 / 1.0 / 1.4 / 2.0
TREBLE-F: 5 K / 10 K / 15 K
TREBLE-Q: 0.7 / 1.0 / 1.4 / 2.0
Then press the [CONTROL] knob (left /
right) to select USER preset including:
BALANCE -> FADER -> M-B EX ->HPF(high
pass filter) -> LPF(low pass filter) -> S-W
V O L ( S u b w o o f e r V o l u m e ) , rotate the
[CONTROL] knob to select a value.
BALANCE:LEFT 1-7->CENTER->RIGHT
1-7
FADER:FRONT 1-7->CENTER->REAR 1-7
M-B EX: ON/OFF
HPF: THROUGH/60/90/120
LPF: THROUGH/60/90/120
SUBW VOL: (-6)-(+6)
Notes:
1. After auto store, the previous stored
stations will be overwritten.
2. The unit has 4 bands, such as FM1, FM2,
FM3 and AM. FM3 and AM can store
by AS function. Each bands can store 6
stations, FZ502 can store 24 stations in
total.
Manual store
When one expected radio station has been
detected, press and hold number button
on the remote control 1-6 to store it in the
memory.
Recall the stored stations
Note:
Press one numeric button among 1 to 6 on
the remote control or on the panel to select
the corresponding stored station.
When a station is received, searching stops
and the station is played.
Local seeking
Preset scan
When LOCAL seeking is on, only those
radio stations with strong radio signal could
be received.
Refer to System Setup page 5.
Preset scan receives the stations stored
in preset memory in order. This function is
useful when searching for a desired station
in memory.
1. Press the [SCN/PS/AS] button on the
remote control.
2. When a desired station is tuned in, press
the [SCN/PS/AS] button on the remote
controlagain to continue receiving that
station.
English
Note:
Radio Operations
Note:
The number of radio stations that can be
received will decrease after the local seeking
mode is on.
Note:
Be careful not to press and hold the
[SCN/PS/AS] button, otherwise the auto
store function is engaged and the unit starts
storing stations.
FZ502
6
SiriusXM Satellite Radio Operations
SiriusXM Satellite Radio Operations
Displaying the Identification (ID)
Code
Note:
English
Before you listen to satellite radio, you must
subscribe to the service using the SiriusXM
Radio ID number.
1.Press the [CONTROL] knob on the front
panel or [SRC / ] button on the remote
control to activate SiriusXM-mode.
2.Press the [CONTROL] knob (left/right) to
select channel “0”.
The unit displays Radio ID.
Notes:
1. The Radio ID is located on the bottom of
the SiriusXM Connect Vehicle Tuner.
2. Please note that the SiriusXM Radio ID
does not include the letters I, O, S or F.
3. Activate the SiriusXM Connect Vehicle
Tuner using one of the two methods
below:
• Online: Go to “www.siriusxm.com/
activatenow” and choose ACTIVATE
RADIO.
• Phone: Call 1-800-XM-RADIO (1-800-9672346).
Storing Channel Presets
1. Press [BAND/TOP] button on the remote
control or long-press [CONTROL] knob
(up) on the front panel to select the
desired band you want to store the preset
in.
There are 3 Satellite Radio Preset bands.
Each press of [BAND/TOP] button on the
remote control or long-press [CONTROL]
(up) on the front panel changes the band: SXM1 -> SXM2 -> SXM3 -> SXM1
2.T une to the desired channel and then
press and hold one of the preset buttons (1
through 6) on the remote control to store
the channel.
3.R epeat the procedure to store up to 5
other channels on to the same band.
Note:
•A total of 18 channels can be stored in the
preset memory, 6 channels for each band
(SXM1,SXM2 and SXM3).
7
FZ502
Tuning Channels using Presets
1.Press [BAND/TOP] on the remote control
or long-press [CONTROL] knob (up) on
the front panel to select the desired band
of Presets you wish to access.
2.Press [CONTROL] knob (up/down) to the
preset buttons (1 through 6) that has your
desired Satellite Radio channel stored in
memory.
Category Browsing
1. Long-press and hold [BAND/TOP] on the
remote control to activate the Category
Browsing mode.
2.Rotate [CONTROL] knob to select desired
category.
3.P ress [CONTROL] knob (left/right) to
select desired channel within the selected
Category. You can see channel name,
channel number, artist, title or content by
pressing [DISP] on the remote control.
4.P r e s s [ CONTROL] k n o b t o t u n e t o
selected channel.
Note:
•If no operation is performed for 10
seconds or press [CONTROL] knob (up),
the Category Browsing mode is canceled.
Preset scan
Preset scan receives the stations stored
in preset memory in order. This function is
useful when searching for a desired station in
memory.
1.Press and hold the [PS/AS] button on the
remote control.
2.When a desired station is tuned in, press
the [PS/AS] button on the remote control
again to continue receiving that station.
Channel scan (in current category)
Channel scan receives the channel (in
current category) in order. This function is
useful when searching for a desired channel
in current category.
1.Press the [PS/AS] button on the remote
control.
2.When a desired channel is tuned in, press
the [PS/AS] button on the remote control
again to continue receiving that channel.
•Be careful not to press and hold the
[PS/AS] button on the remote control for
1 second or longer, otherwise the preset
scan function will begin and the unit starts
scaning presets.
Artist & Song Alerts
While listening to SiriusXM Satellite Radio,
you can be alerted when your favorite songs
or artists are playing on other channels. The
radio will display an Alert message when a
matching artist or song is found on another
channel. Then you can choose if you want to
tune to that favorite or you can ignore it and
stay on your current channel. Information
on setting up the Artist and Song alerts is
described below.
1. While listening to favorite song, short-press
[RPT] button on the remote control to add
the artist or long-press [RPT] on the remote
control button to add the song to the “Artist
& Song Alerts” list.
Press and hold [CONTROL] knob (center
long press), and rotate the [CONTROL]
knob to choose ADJUST, then to choose
the SEARCH, and rotate [CONTROL] knob
to select “ALERT LIST”.
Rotate and press [CONTROL] knob to
select desired alert item. Then select “ON”
to activate alert, “OFF” to deactivate or
“DELETE” to delete this item. (press and
hold [CONTROL] knob) You can also
activate and deactivate Alert function in
System Setup menu.
Notes:
•You can store up to 50 items for Artist
& Song Alerts. “XU(sed)/YE(mpty)” is
displayed when the new item is stored. X
is the total number of song titles or artist
names stored in memory, and Y is the total
number memory locations still available for
storage.
•If either the artists or song title is not
available, “NO SONG” or “NO ARTIST” will
be displayed.
•If you try to store item when memory is full,
“MEMORY FULL” is displayed. If you want
to store another, please delete exsisting
alert item.
Receiving and Tuning to an Alert
Whenever a stored artist or song is playing
on another channel, alert message “ART
ALERT”or “SNG ALERT” appears on
the unit display.To tune to artist or song
identified by the alert, press [RDM] button on
the remote control.
Notes:
•If no operationg is performed for 5
seconds,the unit returns to normal mode.
•Artist name and Song title which you have
stored and which are currently playing
will be displayed in category called “MY
MUSIC” in search mode.
My Music search
You can access the channels which is
broadcasting the contents in the activated
Alert list.
1. Press and hold [CONTROL] knob (center
long press), and rotate the [CONTROL]
knob to choose ADJUST, then to choose
the SEARCH, and rotate [CONTROL]
knob to select “MY MUSIC LIST”.
2. P r e s s [ CONTROL] k n o b t o d i s p l a y
matched songs which are currently
broadcasted
3.Rotate [CONTROL] knob to select desired
song, and press [CONTROL] to tune to
that channel.
Note:
•If there is no matched songs broadcasted,
it displays “MEM EMPTY”.
Replay function
The Replay feature allows you to pause,
rewind, and replay up to 30 minutes of live
SiriusXM Satellite Radio.
1.W hile listening to a SiriusXM channel,
press [ ] on the remote control to enter
Replay mode. The display will show
“PAUSE” when entering this mode.
2.Press [CONTROL] knob (down) or press
[ ] button to resume playback of the
stored audio from the point at which it
was paused.
During playback,the SiriusXM Tuner will
continue to store the channel audio until
you exit the Replay mode.
SiriusXM Satellite Radio Operations
During REPLAY playback:
•Fast rewind: Press and hold [CONTROL]
] on the
knob (left), or press and hold [
remote control.
•Fast
forward: Press and hold [CONTROL]
] on the remote
knob (right), or press [
control.
•Returning to the beginning of the current
song: Press [CONTROL] knob (left),
] on the remote
or press and hold [
control.
(If you press [CONTROL] knob (left), or
] on the remote control. in the
press [
first 2 seconds of a song, you return to
the beginning of the previous song.)
•Advancing
to the beginning of the next
song: press [CONTROL] knob (right)
] on the remote
or press and hold [
control.
3. Press [BAND/TOP] to finish Replay mode.
Parental Lock / Unlock
The SiriusXM Parental Control feature allows
you to control access to channels that you
consider inappropriate for younger listener.
When enabled, the Parental Control feature
requires you to enter a password to tune to
the locked channels. Information on setting up
the password, setting up the channels to be
locked, and the method to access the locked
channels is described below.
1. Long-press [CONTROL] knob and select
ADJUST, then press [CONTROL] knob to
enter and press [CONTROL] knob (right) to
select “PARENTAL PASSWORD”.
P r e s s [ C O N T R O L ] k n o b t o c h a n g e
password. Enter old password, new
password. To enter code, rotate
[CONTROL] knob to decide number and
[CONTROL] knob (left/right) to select digit.
Each time you need to press and hold
[CONTROL] knob to confirm password.
(Original password is “0000”, after
input four numbers, then long-press the
[CONTROL] knob)
2.Press and hold [CONTROL] knob (down)
or press [ISR] button on the remote
control while the desired song is playing.
3.When completed, “STORED TAG X OF
64” is displayed.
X means the number of tag stored.
Notes:
•If you continue to press [CONTROL] knob
] on the
(right), or press and hold [
remote control. until the end,the Replay
mode is canceled, and the unit will
change to live SiriusXM radio mode.
•If you change channels while in Replay
mode,the unit will exit Replay mode to
live Satellite mode and clear the Replay
memory.
•R eplay mode is being kept when you
change the source other than SiriusXM
mode.
•During tagging, the iPod/iPhone takes priority to save the tag information.If
no iPod/iPhone is connected, the tag
information is saved to this unit.
•This unit can store up to 64 pieces of
tag information. When the memory of
the unit is full, “MEMORY FULL” may be
displayed.
•When iPod/iPhone that doesn’t support
th e ta g g i n g fu n c ti o n i s co n n e c te d ,
“TRANSFER FAIL” may be displayed.
•If there is stored tag information on the
unit, when an iPod/iPhone supporting the
tag function is connected, the stored tag
information will be transferred to iPod/
iPhone automatically.
•I f t a g i n f o r m a t i o n a l r e a d y e x i s t s ,
“ALREADY TAGGED” will be displayed
when you try to tag information again.
•Tagging may be canceled by changing
the frequency or station.
•If a song is tagged and the remaining
storage volume of the connected iPod/
iPhone is sufficient to hold the song’s tag
information, it will be saved on the iPod/
iPhone.
iTunes song tagging
Changing the Display
With iTunes song tagging, you can tag songs
you hear while listening to SiriusXM Satellite
Radio. The tagging information is saved in
your radio until you connect your iPod or
iPhone and then the tagging information is
transferred to your iPod/iPhone. When your
iPod/iPhone to iTunes, you will then be able
to preview and purchase the song that you
heard while listening to SiriusXM Satellite
Radio.
Information on using the iTunes song
tagging feature is described below.
Text information, such as the channel name,
artist name/feature, song/program title and
content is available with each SiriusXM
channel. The unit can display this text
information as explained below.
1.In SiriusXM mode, press [DISP] button on
the remote control.
Each time you press this button, the
display changes as shown below.
Band/Channel number/channel name =>
Artist Name => Song Title=> Content Info
=> Category Name => Clock => Band/
Channel number/channel name
* If there is no text information,nothing will
be displayed.
Notes:
1.A song may be tagged while listening to a
SiriusXM channel if the display shows the
“TAG” icon.
2. Long-press [CONTROL] knob and select
ADJUST, then press [CONTROL] knob
to enter and press [CONTROL] knob
(right) to select “LOCK CH” and press
[CONTROL] knob to start to lock channel.
You will be asked to input password.
Enter password and “LOCK” will be
displayed if it is successful.
3. Long-press [CONTROL] knob and select
ADJUST, then press [CONTROL] knob to
enter and press [CONTROL] knob (right) to
select “UNLOCKCH”. Enter password and
you can unlock the channel.
4. F or accessing the locked channels,
select channel by “DIRECT SELECT”.
Press and hold [CONTROL] knob (center
long press), and rotate the [CONTROL]
knob to choose ADJUST, then to choose
the ”SEARCH”, and rotate [CONTROL]
knob to select “DIRECT SELECT” and
press [CONTROL] knob. Input desired
locked channel (need to input 3 digit) and
input password, then you can tune to that
locked channel.
English
SiriusXM Satellite Radio Operations
HD Radio Operations
About HD Radio™ Technology
Select a band
HD Radio Technology allows CD-quality
digital broadcasting of your local AM and
FM radio stations. HD Radio broadcasts
can include multiple channels on the same
frequency, which is called multicasting. With
multicasting, you can receive up to eight
additional multicast channels: HD1~HD8.
With an HD Radio tuner connected, you
will receive HD Radio digital broadcasts
automatically when tuned to a station that
offers HD Radio Technology.
Press and hold the [CONTROL] knob (up
long press) on the panel or [BAND/TOP]
button on the remote control to change
between three FM and one AM bands. Each
band stores up to six preset stations.
NOTE: Not all FM or AM stations offer
HD Radio (digital) broadcasting. You can
receive both analog and digital stations
with the unit.
Accessing radio mode
Press the [CONTROL] knob or [SRC / ] button
on the remote control to switch to the HD
RADIO source, and HD icon will illuminate.
Tuning
- Seek Tuning
Press and hold the [CONTROL] knob (left /
right) on the panel or [
,
] buttons on
the remote control to seek the next/previous
station automatically.
- Manual Tuning
Press the [CONTROL] knob (left / right)
on the panel or [
,
] buttons on the
remote control to move the radio frequency
number up or down one step.
FZ502
8
iTunes® Tagging
HD Radio Operations
English
HD Radio multicast channels
Note:
To tune to an HD Radio multicast channel,
tune to the main signal and then press the
[CONTROL] knob on the panel. PTY and
SUB CH are displayed. Select PTY or SUB
CH by rotate [CONTROL] knob and push to
confirm.
• Select PTY type from the category list by
rotate [CONTROL] knob and push.
• Select SUB CH by rotate [CONTROL]
knob and push.
• Multi channel is available when a digital
signal is detected, the DIGITAL icon will
illuminate. If the digital signal becomes
unavailable, the unit will revert to Analog
reception.
Multicast stations can be stored as
presets, but the unit must be in Digital or
Auto reception mode to receive them.
Press [SCN/PS/AS] button on the remote
control to scan and play all preset stations
for 10 seconds each. Press [SCN/PS/AS]
button on the remote control again to stop
scanning and play the current station.
Preset stations
Automatic store (AS)
Up to six stations on each band can be
stored as presets, which can then be instantly
recalled by pressing the associated preset
button. To store a station, turn the radio on
and select the desired band and station.
Press and hold the desired preset button
(numbered one through six on the remote
control). When stored, the preset number
will appear in the display. The station is now
stored and can be recalled by pressing the
corresponding preset button. Repeat for the
remaining five presets on the current band
and for presets on the other four bands.
Preset scan
Note:
Be careful not to press and hold the
[SCN/PS/AS] button on the remote control,
otherwise the auto store function is engaged
and the unit starts storing stations.
Press the [SCN/PS/AS] button on the remote
control to select six strong stations and store
them in the FM3 or AM band using the auto
store function. After entering the stations into
memory, the unit will automatically stop at
each station for five seconds, allowing you to
preview each selection. When using the auto
store function, the new stations replace any
stations already stored in preset memory.
Note:
You can stop the auto store function at any
time by pressing the [SCN/PS/AS] button on
the remote control again.
iTunes® Tagging
The unit offers iTunes ® Tagging, which
allows the user to "Tag" songs playing on
HD Radio™ stations for purchase later
through iTunes. When press [ISR] button on
the remote contorl, the unit stores the title
and artist song information that can then be
transferred to your iPod when connected to
the unit. A list titled "Tagged" will appear in
iTunes, allowing you the option to purchase
your tagged songs.
9
FZ502
Note:
“iTunes® Tagging” function works by
connecting THD301 (sold separately).
iPod compatibility
For detailed information on the playable iPod
models, see our home page: www.clarion.
com
Note:
Downloading tags to your iPod
Tagging music
To download tags to your iPod, plug your
iPod into the unit. All existing tags are
automatically transferred to the iPod and
deleted from the head unit’s memory.
If your iPod is connected when a song
is tagged, the Tag will be immediately
transferred to the iPod.
• iPhone can also be connected to this system
and “iPod” appearing in this manual should
be referred to as “iPod/iPhone”.
• This system will not operate or may operate
improperly with unsupported versions.
To begin tagging music, tune to an HD Radio
station. The DIGITAL icon at the display must
be illuminated, indicating a digital station
is being received. TAG icon lights up when
Tagging function is ready. Press the [ISR]
button on the remote control. The tagging
function is highly depends on the receptions
of the radio station. If the channel reception
is insufficient, it will effect the operation of the
tagging function.
“Stored Tag ## of 64” will appear in the
display. The song information is saved to the
unit memory until your iPod is connected. You
can tag up to 64 songs before the tags must
be transferred to your iPod or deleted. When
the Tag memory reaches capacity (64 tags)
the bottom of the screen displays “Memory
Full”.
Table 5: TAG Messages
Tag Message
Reason
S T O R E D T A G # # If the Tag data is ready, and
OF 64
[ISR] button on the remote
control is pressed
SENDING HD TAG Tag data is sending to iPod
##
MEMORY FULL
Tag storage is full
TAG DATA IS NOT Tag data is not available
AVAILABLE
IPOD FULL
iPod memory is full
TAG NOT SUPPORT When connect and press
[ISR] button on the remote
control, the iPod without
Tagging function
Note:
Tags saved to your iPod can be managed
using the iTunes software, available at www.
apple.com/itunes.
Note:
When transferring Tags to your iPod, the
unit must remain in HD Radio mode. To
purchase tagged songs, you must sync
your iPod to iTunes and then click the
“Tagged” list on the left side of the iTunes
software screen. Click the “view” button for
purchasing information.
Notes:
1. H o w t o e n t e r t h e i T u n e s t a g g i n g
function?
“TAG” and “DIGITAL” light up when
Tagging function is ready, press [ISR]
button on the remote control to start
iTunes Tagging.
2. What is seen on the radio’s display to
let me know I have tagged the tune?
Press [ISR] button on the remote control
to show “STORED TAG## OF 64”. After
connect to your iPod, the display shows
“SENDING HD TAG##”.
If no connection, the display will show
“STORED TAG## OF 64”. You could
save 64 Tag into E2PROM in total.
When you connect to your iPod, Tag
information will be saved in the iPod,
and the data in E2PROM will be
cleared.
3. Then how do I get the tagged tune from
my iPod to the computer?
If you have install iTunes, connect your
iPod to your computer and buy songs
online.
USB Operations
1.Move the cover of the USB slot to the left.
Insert a USB cable (CCA-755) into the
USB slot. Insert a USB device into the USB
cable.
When connecting a USB device, the unit
will read the files automatically.
2.To remove the USB device, you should first
select another source or turn off the power,
in order to avoid damaging the USB device.
Then take off the USB device. Move the
cover to the right.
Top function
Pausing play
1.Press the [
] button on the remote control
to pause play.
“PAUSE” appears in the display.
]
2.To resume MP3/WMA play, press the [
button on the remote control again.
Selecting a track
Track-up
1.Press the [CONTROL] knob (right) on the
] button on the remote control
panel or [
to move to the beginning of the next track.
2.Each time you press the [CONTROL] knob
] button on the
(right) on the panel or [
remote control, the track advances to the
beginning of the next track.
Track-down
1.P ress the [CONTROL] knob (left) on the
] button on the remote control
panel or [
to move back to the beginning of the
current track.
2.P ress the [CONTROL] knob (left) on the
] button on the remote control
panel or [
twice to move back to the beginning of the
previous track.
Fast-forward/Fast-reverse
Fast-forward
Press and hold the [CONTROL] knob (right)
] button on the remote
on the panel or [
control.
Fast-reverse
Press and hold the [CONTROL] knob (left) on
] button on the remote control.
the panel or [
The top function resets the USB player to the
first track of the USB device. Press and hold the
[ CONTROL ] knob (down) to play the first
track (track No. 1) on the USB device.
*In case of MP3/WMA, the first track of the
current folder will be played.
Other various play functions
CCA-755
*For MP3/WMA USB device, it takes
some time until the start of searching
and between tracks. In addition, some
errors may occur in the play time.
Folder Select
This function allows you to select a folder
containing MP3/WMA files and start
playing from the first track in the folder.
1.Press and hold [CONTROL] knob (up)
on the panel.
Press and hold [CONTROL] knob (up)
on the panel to move the next folder.
2.To select a track, press the [CONTROL]
knob (right / left) on the panel or
,
]button on the remote control.
[
Search Function
1.P ress the [CONTROL] knob (up) to
enter fold sch mode, and press
[CONTROL] knob (center) to comfirm,
then rotate [CONTROL] knob to select
the folder list search mode.
2.Rotate the [CONTROL] knob to select a
folder.
3.Press the [CONTROL] button (center)
to enter the file list search mode. And
then the track list appears in the display.
4.Turn the [CONTROL] knob to select a
track.
5.Press the [CONTROL] knob (center) to
play.
* When play back MP3 / WMA file, this
function is performed in the current
folder.
Scan play
This function allows you to locate and play the
first 10 seconds of all the tracks recorded on a
USB.
Press the [ SCN/PS/AS ] button on the remote
control to perform scan play.
2.For MP3/WMA files, press [ RPT ]
button on the remote control repeatedly
until “FOLD RPT” appears on the display
for folder repeat play.
3.Press [ RPT ] button on the remote
control repeatedly until “RPT OFF”
appears on the display to cancel repeat
playback, and “RPT” segment goes off.
English
USB Operations
Random play
This function allows you to play all tracks
recorded on a USB device in a random
order.
Press the [ RDM ] button on the remote
control to perform random play.
Repeat play
This function allows you to play the current
track repeatedly or play a track currently being
played in the MP3/WMA folder repeatedly.
1.Press the [ RPT ] button on the remote
control once or more until “TRK RPT”
appears on the display to perform repeat
play, and “RPT” segment lights on.
iPod & iPhone Operations
Connect
Connect your iPod or iPhone to the USB slot
via CCA-748 cable.
When connecting a device, the unit will read
the files automatically. The track information
display on the screen once playback start.
MENU
In the S-CTRL OFF mode, press the
[CONTROL] knob (up), rotate the knob select
“MUSIC” or “VIDEO”.
Select “MUSIC”, press the [CONTROL] knob,
then rotate the [CONTROL] knob to show
PLAY LISTS / ARTISTS / ALBUMS / GENRES
/ SONGS / COMPOSERS, then press the
[CONTROL] knob to confirm.
Select “VIDEO”, press the [CONTROL] knob,
then rotate the [CONTROL] knob to show
MOVIES / MUSIC VIDEO / TV SHOWS /
VIDEO PODCASTS / RENTALS, then press
the [CONTROL] knob to confirm.
Monitor
CCA-748
Note:
•In case of VIDEO Playback, CCA-748
cable and monitor (sold separately) are
required.
FZ502
10
iPod & iPhone Operations
English
•VIDEO MENU item is different by the
model of connected iPod and language
setting.
Notes:
This function allows you to play the current
track repeatedly or play all tracks in your
iPod/iPhone repeatedly.
1.P ress the [RPT] button on the remote
control once or more until “RPT ON”
appears on the LCD to perform repeat
play.
2.Press [RPT] button on the remote control
repeatedly until “RPT OFF” appears on
the LCD to cancel repeat playback.
•When performing iPod operations using
simple control mode, make the operations
slowly. If repetitive operations are
performed too quickly, unforeseen errors
may occur.
•When performing iPod operations using
simple control mode, please do not
operate the iPod and the unit at the same
time, otherwise there may be unexpected
event happened.
•Some iPod models do not support this
function. Consult your nearest Clarion
dealer or website to confirm which models
do not support this function.
Random play
iPod menu alphabet search
Repeat play
This function allows you to play all tracks in a
random order.
1.P ress the [RDM] button on the remote
control once or more until “RDM ALBUM”
appears on the LCD for album random play.
2.P ress the [RDM] button on the remote
control once or more until “RDM SONG”
appears on the LCD to perform random
play.
3.P ress the [RDM] button on the remote
control once or more until “RDM OFF”
appears on the LCD to cancel random
playback.
Setting iPod simple control mode
Use this function if you wish to operate
through your iPod connected to this unit via
the USB cable.
* The factory default setting is “ OFF “.
1. Press and hold [CONTROL] knob (center),
and rotate the [CONTROL] knob choose
ADJUST, then press the [CONTROL] knob
(center) to enter system setup.
2Press the [CONTROL] knob (left / right) to
select “ S-CTRL“.
3.Rotate the [CONTROL] knob to select “
ON “ or “ OFF “ .
•O N: Operations are made through your
iPod.
•O F F: O p e r a t i o n s c a n n o t b e m a d e
through your iPod.
11
iPod & iPhone Operations
FZ502
This function searches the subfolders for
desired alphabetical letters.
1.P ress the [CONTROL] knob (up), and
rotate [CONTROL] knob to select the
iPod menu mode.
2.Rotate the [CONTROL] knob to switch
between categories.
MUSIC: PLAYLISTS, ARTISTS, ALBUMS,
GENRES, SONGS, COMPOSERS
VIDEO: MOVIES, MUSIC VIDEOS, TV
SHOWS VIDEO PODCASTS, RENTALS
3.P r e s s t h e [ C O N T R O L ] k n o b . ( T h e
contents of the category are displayed.)
4.P ress and hold the [CONTROL] knob
(down).
5.Rotate the [CONTROL] knob to select the
desired letter to search.
6.P ress the [CONTROL] knob (down) to
perform search.
7.Roted the [CONTROL] knob to select and
press the [CONTROL] knob to confirm.
Listening to PANDORA
You can listen to Pandora internet radio by
connecting an iPod/iPhone that has Pandora
Application already installed.
To start streaming, connect the iPod/iPhone
with Pandora already launched.
When the unit displays “PLEASE LAUNCH
PANDORA APPLICATION ON MOBILE
DEVICE” in PANDORA mode, please launch
the PANDORA Application by operating the
iPod/iPhone connected.
1.P ress the [CONTROL] knob (push) to
enter the Pandora mode.
Selecting a station from list
Press the [CONTROL] knob (up) to enter the
station list.
Rotate the [CONTROL] knob to select ”BY
DATE” or ”A-Z” and press the [CONTROL]
knob to confirm.
• BY DATE: List in an created date order
• A-Z: List in an alphabetical order
Note:
If the name of the station you wish to create
for a track title or an artist name is the same
as the station name currently playing, “NOW
PLAY” appears on the display and the station
will not be created.
Skip
Press the [BAND/TOP] button on the remote
control for the next song in station.
Note:
Go to next station or previous station(an
alphabetical order)
Press the [CONTROL] knob (right) on the
] button on the remote control
panel or [
to go to next station.
Press the [CONTROL] knob (lift) on the
] button on the panel or remote
panel or [
control to go to previous station.
Thumbs up/down
1. P ress the [RDM] button on the remote
control for the thumbs up.
2. Press the [SCN] button on the remote
control for the thumbs down.
Notes:
•You can personalize your stations by
“thumbs up” or “thumbs down”.
•Pandora limits the number of thumbs down
allowed on their service.
If you attempt to thumbs down songs
beyond the limit, the current song
continues to playback.
BOOKMARK artist or song
Press the [RPT ] buton on the remote control
to Bookmark artist.
Prsee and hold the [RPT ] button on the
remote control to Bookmark current artist of
the song.
Creating new stations
Press the [1] button on the remote control to
create a new station from the current artist.
Press and hold the [1] button on the remote
control to create a new track.
•Pandora limits the number of skips allowed
on their service. If you attempt to skip
songs beyond the limit, ”SKIP LIMIT” is
displayed.
Play/Pause
Press the [ ] button on the remote control
for play/ pause.
Bluetooth Operations
Notes:
•Leaving it exposed to high temperatures
or direct sunlight can cause distortion
or discoloration which may result in a
malfunction.
•This system will not operate or may
operate improperly with some Bluetooth
audio players.
•C l a r i o n c a n n o t g u a r a n t e e t h e
compatibility of all mobile phones together
with unit.
•Audio playback will be set to the same
volume level as set during telephone call.
This might cause problems, if extreme
volume level is set during telephone call.
Handsfree Operations
Pairing
1.Turn on Bluetooth function of your mobile
phone.
2.E nter mobile phone’s Bluetooth setup
menu.
3. Search for new Bluetooth devices.
4.Select FZ502 from the pairing list on the
mobile phone.
5.E nter “0000” as the password (The
password default setting is “ 0000 ”).
6.A fter pairing successfully, the unit will
enter Bluetooth mode automatically, and
“BLUETOOTH CONNECTED” will appear
on the LCD.
Making a call
Operation from Bluetooth menu
Press the [CONTROL] knob to switch the
source to “BLUETOOTH”.
Press and hold the [CONTROL] knob
(center) choose ”ADJUST”, then rotate the
[CONTROL] knob select ”CALL LST”.
1.Press the [CONTROL] knob.
Bluetooth Operations
2.Rotate the [CONTROL] knob on the front
panel to switch:
DIAL NUMBER / DIALLED CALL /
MISSED CALL / RECEIVED CALL /
USER PHONEBOOK
• DIALl NUMBER
1.Rotate the [CONTROL] knob to choose
”DIAL NUMBER” and press the
[CONTROL] knob (push) to confirm.
2. Rotate the [CONTROL] knob to select
a number, press the [CONTROL] knob
(right) to confirm and ready to input the
next digit. Repeat the above until all
numbers inputted.
3. Press the [CONTROL] knob (push) to
dial.
4. Press the [CONTROL] knob (right) to
terminate call.
• Dialled/Missed/ Received
You can search any Dialled / Missed /
Received.
1.R otate the [CONTROL] knob to select
“DIALLED”, “MISSED” , “RECEIVED”.
2.Press the [CONTROL] knob to enter the
selected call history.
3.Press the [CONTROL] knob to scroll the
contacts.
4.When the contact name or mobile phone
No. is displayed, press the [CONTROL]
knob (push) to call the mobile phone
No.of that contact.
*Press the [CONTROL] knob (right) to end
the call.
• Call from Phonebook
User can search the contact name in the
phonebook and make call.
1.R otate the [CONTROL] knob to select
“USER PHONEBOOK” .
2.Press the [CONTROL] knob to enter the
selected.
3.Rotate the [CONTROL] knob to scroll the
contacts.
4.T he phone number and the name to
scroll display.When the contact name is
displayed, press the [CONTROL] knob
(push) to call the mobile phone No. of that
contact.
*Press the [CONTROL] knob (right) to end
the call.
Notes:
•Some mobile phones may not be able to
transfer data of Phonebook.
•After RESET, please wait few minutes until
data transferred following to the
Bluetooth mode selection. During that,
“PBK UPDATE” is on the display.
• Redial
You can call last dialed number.
Press the [CONTROL] knob (up) to enter
redial.
Press the [CONTROL] knob (push) to dial
when display ”REDIAL”.
Transfer Call
•You
can switch Handsfree call and mobile
phone call.
Press the [CONTROL] knob (left) button
during call.
• Answering a call
You can answer an incoming call by pressing
the [CONTROL] knob (left).
* Press the [CONTROL] knob (right) to reject
an incoming call.
• Answering a call
You can answer an incoming call by pressing
the [CONTROL] knob.
*Press the [CONTROL] knob (right) to
reject an incoming call.
Audio Streaming Operations
What is audio streaming?
Audio streaming is a technique for transferring
audio data such that it can be processed as
a steady and continuous stream. Users can
stream music from their external audio player
to their car stereo wirelessly and listen to the
tracks through the car’s speakers. Please
consult your nearest Clarion dealer for more
information on the product of wireless audio
streaming transmitter offered.
CAUTION
Please avoid operating your connected
mobile phone while audio streaming as
this may cause noise or sound choppy on
the song playback.
Audio streaming may or may not resume
after telephone interrupt as this is
dependent on mobile phone.
System will always return to Radio mode
if audio streaming is disconnected.
Note:
Be sure to read the chapter “Pairing” before
proceeding.
Play / Pause a track
English
The Bluetooth allows you to utilize your car’s
built-in audio system for wireless mobile
phone or music handsfree communication.
Some Bluetooth mobile phones have the
audio features, and some portable audio
players support Bluetooth feature. This
system can play audio data stored in a
Bluetooth audio device. The car stereo with
Bluetooth will be able to retrieve phonebook
contacts, received call, dialed call, missed
call, incoming calls, outgoing call and listen
to music.
1.Press the [CONTROL] knob (down) or
[
] button on the remote control to
pause audio playback.
2.T o resume audio playback, push the
[CONTROL] knob (down) or [
] button
on the remote control again.
Selecting a track
Track-up
1.P ress the [CONTROL] knob(right) or
[
] button on the remote control to
move to the beginning of the next track.
2.Each time the [CONTROL] knob(right)
or [
] button on the remote control is
pressed, playback proceeds to another
track in the advancing direction.
Track-down
1.Press the [CONTROL] knob(left) or
[
] button on the remote control to
move to the beginning of the previous
track.
2.E ach time the [CONTROL] knob(left)
or [
] button on the remote control is
pressed, playback proceeds to previous
track in the reverse direction.
Note:
Playing order will depend on Bluetooth
audio player. When press the [CONTROL]
knob(left) or [
] button on the remote
control is pressed, some A2DP devices will
restart the current track depends on the
duration of playback.
During music streaming playback, “A2DP”
will be shown on the display. Information
about tracks (e.g. the elapsed playtime,
song
title, etc.) cannot be displayed on this
unit. When A2DP device is disconnected,
“DISCONNECT” will be shown on the
display
and return to previously selected audio
source. Some Bluetooth audio players may
not have play / pause synchronized with
FZ502
12
Bluetooth Operations
English
this unit. Please make sure both device and
main unit are in the same play / pause status
in BT MUSIC mode.
ID3 display
During music streaming playback, for music
information that is longer than the display
panel:
When SCROLL is ON, the LCD will display
ID3 TAG information cyclely, e.g:
ALBUM->TITLE->ARTIST..
When SCROLL is OFF, the LCD will display
one of the ID3 TAG information, the default
is TRACK, but user can adjust it to other ID3
TAG information by press the [DISP] button
on the remote control.
5. TROUBLE SHOOTING
GENERAL
Problem
Unit can not
power on.
Cause
Measure
Unit fuse blown.
Replace with new fuse of correct rating.
Car battery fuse blown.
Replace with new fuse of correct rating.
Unit can not
power on.
Nothing happens
when buttons are The microprocessor has
pressed.
malfunctioned due to noise, etc.
Display is not
accurate.
Turn off the power.
Press the [RESET] button with a thin rod.
Note:
When the [RESET] button is pressed, turn off
the ACC power.*
* When the [RESET] button is pressed,
frequencies of radio stations, titles, etc. stored in
memory are cleared.
Improper audio output connection. Check wiring and correct.
Volume set too low.
No/low audio
output.
AUX Operations
Press the [CONTROL] knob on the panel or
[SRC/ ] button on the remote control once or
more to select “AUX”.
AUX is just for audio content with 3.5mm
Jack connector plugged into audio-in socket
on the front panel on the right of USB slot.
AUX Input sensitivity setting
1.Press and hold the [CONTROL] knob .
2.Turn the [CONTROL] knob to select “AUX
SENS”.
3.If the output level of connected external
audio player is “HIGH”, rotate the
[CONTROL] knob and choose “LOW”.
And if the output level is “LOW”, choose
“HIGH”.
FZ502
Replace speakers.
Heavily biased volume balance.
Adjust the channel balance to center position.
Speaker wiring is in contact with
metal part of car.
Insulate all speaker wiring connections.
Speaker power rating does not
match unit.
Replace speakers.
Poor sound quality
or distortion.
Wrong connections.
Speaker is shorted.
Unit resets itself
Incorrect connection between
when engine is off. ACC and Battery.
Check wiring and correct.
Check wiring and correct.
Check wiring and correct.
USB Devices
Problem
USB device cannot
be inserted.
USB device is not
recognized.
Cause
Measure
The USB device has been
inserted with wrong direction.
Reversing the connection direction of the USB
device, try it again.
The USB connector is broken.
Replace with a new USB device.
The USB device is damaged.
Disconnect the USB device and reconnect. If
the device is still not recognized, try replacing
with a different USB device.
Connectors are loose.
No sound heard
No MP3/WMA file is stored in
with the display “No
the USB device.
File” shown.
Sound skips or is
noisy.
13
Increase volume level.
Speakers damaged.
Store these files properly in the USB device.
MP3/WMA files are not encoded
Use MP3/WMA files encoded properly.
properly.
Bluetooth
Use another device to connect.
FM Tuner
General
Refer to the user manual of the device for how to
enable the function.
Adjust the gain of the internal microphone in
System Setup.
Adjust the gain and position of the external
microphone.
For example, stick the microphone onto the
dashboard so it is close to the driver.
Frequency range: 87.9-107.9MHz
Usable sensitivity: 8dBμ
Frequency response: 30Hz-15kHz
Stereo separation: 30dB(1kHz)
Signal/noise ratio: >55dB
Power supply voltage:
14.4VDC (10.8 to 15.6V allowable),
negative ground
Fuse: 15A
Dimensions of the Main Unit:
188mm Width × 58mm Height × 190mm Depth
7-2/5(width) × 2-7/25(Height) × 7-12/25(Depth)
Weight of the Main Unit: 1.94lb. (0.88kg)
Dimensions of the Remote Control unit:
52mm Width × 7.5mm Height × 85.5mm Depth
2-3/64(Width) × 19/64(Height) × 3-11/32(Depth)
Weight of the Remote Control Unit:
0.77oz. (24g) (including battery)
MP3/WMA mode
Description
Check the SiriusXM tuner connection on the back of the unit to ensure that its correctly
connected.
Ensure the SiriusXM antenna cable is connected to the SiriusXM tuner correctly.
Check the SiriusXM antenna wire for breaks or sharp bends. Replace the antenna if
CHK ANTENA
necessary.
Press RESET located….. If the message remains, the antenna may have been damaged.
The vehicle must be outside, and the antenna must have a clear view of the southern sky.
NO SIGNAL
The magnetic antenna must be mounted on the outside of the vehicle for the best reception.
This channel is not included in your SiriusXM subscription plan.
CHAN UNSUB
Call 1-800-XM-RADIO (1-800-967-2346) to subscribe.
This channel is not a valid SiriusXM channel.
CH UNAVAIL The channel number has been entered incorrectly, or the channel was removed from the
SiriusXM channel lineup
The selected channel has been locked by the parental controls, or a mature channel has
been selected.
CH LOCKED
A prompt to enter the unlock code will appear. Enter the unlock code as described on
page 8.
SUBSCRIPTN An update to your SiriusXM subscription has been received by the SiriusXM tuner. Press
UPDATED
any button to continue.
CHEK TUNER
ERROR 2
Do not support iPod & iPhone.
Specification: USB 1.0/2.0
Playable audio format:
MP3(.mp3): MPEG 1/2/Audio Layer-3
WMA(.wma): Ver 7/8/9.1/9.2
Measure
Change another device.
* The head unit will return to RADIO mode.
If an error display other than the ones described above appears, press the [Reset] button. If the
problem persists, turn off the power and consult your store of purchase.
7”
178mm
Bluetooth
Specification: Bluetooth Ver. 2.0+EDR
Profile: HFP (Hands-free Profile)
PBAP(Phone Book Access Profile)
A2DP (Advanced Audio Distribution Profile)
AVRCP (AV Remote Control Profile)
Send/Receive Sensitivity: Class 2
Maximum power output:
180W (45W x 4)
Speaker impedance: 4Ω (4 to 8Ω allowable)
If an error occurs, one of the following displays is displayed.
Take the measures described below to solve the problem.
Cause
USB
Audio Amplifier
6. ERROR DISPLAYS
Display
MP3 sampling rate: 8 kHz to 48 kHz
MP3 bit rate: 8 kbps to 320 kbps / VBR
WMA bit rate: 8 kbps to 320 kbps
Logical format: ISO9660 level 1,2
J oliet file system
Input
Audio input sensitivity:
High: 320mV (at 1V output)
Mid: 650mV (at 1V output)
Low: 1.3V (at 1V output)
(input impedance 10 kΩ or greater)
Aux-in level: ≤2V
2”
50mm
1-4/5”
46mm
2-7/25”
58mm
163mm
Message
Frequency range: 530-1710kHz
Usable sensitivity (S/N=20dB): 30dBμ
6-2/5”
SiriusXM Advisory Messages
AM Tuner
6-2/3” 170mm
7-2/5” 188mm
1/2” 14 mm
The external microphone is
not set correctly nor properly
positioned.
7. SPECIFICATIONS
190mm
The audio quality
is poor after
connection with a
Bluetooth-enabled
device.
Measure
7-12/25”
Cause
The device does not support the
profiles required for the system.
The Bluetooth function of the
device is not enabled.
The internal microphone gain is
not set correctly.
English
Problem
Cannot pair the
Bluetooth enabled
device with the car
audio system.
Note:
•Specifications and design are subject
to change without notice for further
improvement.
Power Output:
19W x 4 Channels RMS
(4Ω@14.4V≤1% THD+N)
Signal to Noise Ratio:
83 dBA (reference: 1 W into 4 Ω)
*When the [Reset] button is pressed, frequencies of radio stations, titles, etc. stored in memory are
cleared.
FZ502
14
4) Cautions on Installation
8. INSTALLATION / WIRE
CONNECTION GUIDE
English
4.Use the enclosed screws for
installation.
Using other screws can cause
damage. (Figure 3)
1.Prepare all articles necessary for
installing the source unit before
starting.
2.Install the unit within 30° of the
horizontal plane. (Figure 2)
3.If you have to do any work on the car
body, such as drilling holes, consult
your car dealer beforehand.
CONTENTS
1) Before Starting....................................................................... 15
2) Package Contents.................................................................. 15
3) General Cautions................................................................... 15
4) Cautions on Installation.......................................................... 15
5) Installing the Source Unit....................................................... 15
6) Removing the Source Unit..................................................... 16
7) Wiring and Connections......................................................... 17
8) Connecting the accessories................................................... 17
Chassis
Chassis
Damage
Max 30˚
Max. 6 mm (M5 screw)
1) Before Starting
Figure 2
1.This set is exclusively for use in cars with a
negative ground 12 V power supply.
2.Read these instructions carefully.
3.Be sure to disconnect the battery “terminal” before
starting. This is to prevent short circuits during
installation. (Figure 1)
Figure 3
5) Installing the Source Unit
Car battery
Figure 1
1.Place the mounting bracket into the instrument panel, use a screwdriver to bend
each stopper of the mounting bracket inward, then secure the stopper.
2.Wire as shown in Section 7) .
3.Insert the source unit into the mounting bracket until it locks.
4.Take care of the top and bottom of the trim ring and mount it so that all the hooks
are locked.
2) Package Contents
Wire connector..................................... 1
Owner’s manual................................... 1
Warranty card....................................... 1
Remote control (with battery)............... 1
• Console opening dimensions
15
FZ502
2.Use a soft, dry cloth to clean the case.
Never use a rough cloth, thinner,
benzine, or alcohol etc. For tough dirt,
apply a little cold or warm water to a
soft cloth and wipe off the dirt gently.
7-3/16"
(182 mm)
Hole
2-1/8"
3) General Cautions
1.Do not open the case. There are no
user serviceable parts inside. If you
drop anything into the unit during
installation, consult your dealer or an
authorized Clarion service center.
Notes:
1. Some car models require special mounting kits for proper installation. Consult your
Clarion dealer for details.
2. Fasten the front stopper securely to prevent the source unit from coming loose.
53 mm
Source unit........................................... 1
Trim ring............................................... 1
Mounting bracket.................................. 1
Screws M5x6 mm................................. 4
L-key..................................................... 2
Notes of installation
Dashboard
7. DO NOT block the cooling fan exit to
ensure sufficient heating dissipation
of this unit, or it may result in damage
to this unit.
Method B
6) Removing the Source Unit
Disassemble trim ring
1. Push the trim ring to right and pull out the
right part.
Unit installation
Method A
1. Insert mounting bracket into dash
board, choose appropriate mounting
tab according to the gap width, bending
the mounting tab outwards with a
screwdriver to fix the mounting bracket
in place.
M5x6
2. Push the trim ring to left and pull out the
left part.
2. Slide the unit into the bracket until you
hear a click sound.
Screwdriver
English
1. Before installation, please make sure
proper connections are conducted and
the unit operates normally. Improper
connection may result in damage to
the unit.
2. Use only accessories designed and
manufactured for this unit and other
unauthorized accessories may result in
damage to the unit.
3. Before installation, please fasten all power
cables.
4. DO NOT install the unit in the place where
close to hot area to prevent damage to
electrical components such as the laser
head.
5. Install the unit horizontally. Installing the
unit more than 30 degree vertically may
result in worse performance.
6. To prevent electric spark, connect the
positive pole first and then the negative
pole.
Dashboard
Mounting Frame
1. Insert this unit directly to the opening of
the dashboard.
2. Place M5×6 cylindrical screw through the
holes of the mounting frame located inside
the opening to holes of the unit and fasten
the screws to left & right.
Trim ring installation
Disassemble the unit
1. Switch off the power.
2. Remove the trim ring.
3.Insert the removal keys straight back until
they lock,then pull the unit out.
4. Disconnect all the wires.
Attach the trim ring around the front panel.
Mounting Bracket
FZ502
16
7) Wiring and Connections
White
Black
16-Pin Connector Extension Lead
(attached to the source unit)
Rear audio output (Left) /Subwoofer output 1
Gray
Rear audio output (Right) /Subwoofer output 2
English
Red
Brown wire (Phone mute lead)
Front Right
Gray/Black
Gray
White
Connect to cellular phone mute lead.
Left
Right
Front audio output terminal
White
Front Left
Red
White/Black
Purple
Yellow wire (Memory back-up lead)
15A
Connect directly to battery
Rear Right
Purple/Black
Black
Green
SWC
Steering wheel Black
control terminal
Red wire (Power lead)
Accessory
12V
Green/Black
CIM
External microphone
(RCB-199:Sold by
separately)
Rear Left
4-Speaker system
4 Channel Amplifier
Blue/White wire (Amplifier turn-on lead)
Connect to remote turn-on lead of amplifier
or
2-Speaker system
Black wire (Ground lead)
Refer to next page
Gray
Connect to vehicle chassis ground
Front Right
Gray/Black
(Black)
(Black)
White
HD BUS
HD RADIO
Front Left
Antenna
White/Black
THD301
(Sold by separately.)
SiriusXM
(Black)
SiriusXM Connect™ Vehicle Tuner (sold
separately)
Connect it to the car power supply terminal
for illumination
Purple
Purple/Black
This HD Radio Ready receiver is ready
to receive HD Radio broadcasts when
connected to the THD301, sold separetely.
(Black)
Orange/White wire (Illumination lead)
Green
Not used.
Insulate each wire
Blue wire (Auto antenna lead)
Connect it to the car power supply terminal
for antenna
Green/Black
8) Connecting the accessories
•Connecting to the external amplifier
External amplifiers can be connected to the 4 channel RCA output connections.
Ensure that the connectors are not grounded or shorted to prevent damage to the
unit.
17
FZ502
Clarion Co., Ltd.
All Rights Reserved. Copyright © 2012: Clarion Co., Ltd.
Printed in China / Imprimé en Chine / Impreso en China
PN: 127075003929