4-528-303-12(1)
Personal Audio System
GB Operating Instructions
©2014 Sony Corporation
Printed in China
CMT-X5CD
CAUTION
The use of optical instruments with this product
will increase eye hazard.
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN
HAZARD
The model and serial numbers are located on
the bottom exterior of the unit. Record these
numbers in the space provided below. Refer to
them whenever you call upon your Sony dealer
regarding this product.
Model No.
Serial No.
WARNING
For the State of California, USA only
Perchlorate Material-special handling may
apply, See
www.dtsc.ca.gov/hazardouswaste/
perchlorate
Perchlorate Material : Lithium battery contains
perchlorate
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the appliance with
newspapers, tablecloths, curtains, etc.
Do not expose the appliance to naked flame
sources (for example, lighted candles).
To reduce the risk of fire or electric shock, do not
expose this appliance to dripping or splashing,
and do not place objects filled with liquids, such
as vases, on the appliance.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main
plug from the AC outlet immediately.
The nameplate is located on the bottom exterior.
These following indications are located on the
bottom exterior.
This symbol is intended to alert
the user to the presence of
uninsulated“dangerous voltage”
within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
Do not expose batteries or appliances with
battery-installed to excessive heat, such as
sunshine and fire.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the
equipment and receiver.
 Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
 Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
The unit is not disconnected from the mains as
long as it is connected to the AC outlet, even if
the unit itself has been turned off.
Owner’s Record
NOTE:
The remote control supplied with this product
contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it
can cause severe internal burns in just 2 hours
and can lead to death.
Keep new and used batteries away from
children. If the battery compartment does not
close securely, stop using the product and keep
it away from children.
If you think batteries might have been
swallowed or placed inside any part of the body,
seek immediate medical attention.
Important Safety Instructions
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong.
The wide blade or the third prong are
provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete
outlet.
10)Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11) Only use attachments/accessories specified
by the manufacturer.
12)Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13)Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14)Refer all servicing to qualified service
personnel.
Servicing is required when the apparatus
has been damaged in any way, such as
power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
The following FCC statement applies only
to the version of this model manufactured
for sale in the U.S.A. Other versions may
not comply with FCC technical regulations.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
Properly shielded and grounded cables and
connectors must be used for connection to host
computers and / or peripherals in order to meet
FCC emission limits.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
ˎThe
ˎ
BLUETOOTH® word mark and logos are
registered trademarks owned by BLUETOOTH
SIG, Inc. and any use of such marks by Sony
Corporation is under license.
ˎThe
ˎ
N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.
ˎAndroid
ˎ
and Google Play are trademarks of
Google Inc.
ˎThe
ˎ
system names and product names
indicated in this manual are generally the
trademarks or registered trademarks of the
manufacturer. ™ and ® marks are omitted in
this manual.
ˎ“WALKMAN”
ˎ
and “WALKMAN” logo are
registered trademarks of Sony Corporation.
ˎ©
ˎ 2013 CSR plc and its group companies. The
aptX® mark and the aptX logo are trade marks
of CSR plc or one of its group companies and
may be registered in one or more jurisdictions.
the Apple logo, iPad, iPhone, iPod,
ˎApple,
ˎ
iPod classic, iPod nano and iPod touch are
trademarks of Apple Inc., registered in the U.S.
and other countries. App Store is a service mark
of Apple Inc.
ˎ“Made
ˎ
for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specifically to iPod and
iPhone, respectively, and has been certified
by the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note
that the use of this accessory with iPod, iPhone
or iPad may affect wireless performance.
ˎ“Xperia”
ˎ
and “Xperia Tablet” are trademarks of
Sony Mobile Communications AB.
Getting Started
Listening to a CD
Location of Controls
Playing a CD-DA/MP3 disc
Note
1 Press FUNCTION  to select “CD.”
2 Insert a CD to the disc slot  at the top of the
This manual mainly explains operations using the remote, but the same operations can also be
performed using the buttons on the unit having the same or similar names.
Remote
unit.
Load a CD with the label side (printed side)
toward you.
Unit (front/top)
Top
Label side
(printed side)
Before operating this system
Malfunctions that occur during the normal
use of the system will be repaired by Sony in
accordance with the conditions defined in the
limited warranty for this system. However, Sony
will not be liable for any consequences arising
from a failure to play caused by a damaged or
malfunctioning system.
Music discs encoded with copyright
protection technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware
that among those discs, there are some that do
not conform to the CD standard and may not be
playable by this product.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side
with digital audio material on the other side.
However, since the audio material side does
not conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
License and Trademark Notice
ˎWindows
ˎ
Media is either a registered trademark
or trademark of Microsoft Corporation in the
United States and/or other countries.
ˎThis
ˎ
product is protected by certain intellectual
property rights of Microsoft Corporation. Use or
distribution of such technology outside of this
product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary.
ˎMPEG
ˎ
Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and
Thomson.
Plays the programmed track or file in a CD.
1 Select “PROGRAM” in step 5 of “To change the
play mode” , then press
.
2 When using an MP3 disc, press
+/–  to
select the folder containing the tracks or files
that you want to program.
If you want to play all tracks or files in the
folder, press .
file, then select
When you use the remote for the first time
The battery is factory-installed in the remote.
Before using the remote for the first time,
remove the insulation sheet attached to the
battery holder. For details, see “Changing the
battery”.
Plays back automatically. If you switch the
function to “CD” from another function when
a CD is already inserted in the slot, press 
 after “READING” has disappeared from the
display window .
The button of the remote or the unit enables
you to fast-rewind/fast forward, select a track,
file or folder (for MP3 disc), etc.
To eject the CD
Press  (eject)  on the unit.
Note
ˎ8
ˎ cm CD cannot be used with this system.
ˎDo
ˎ not load a CD with non-standard shapes (e.g., heart,
square, star). Doing this may cause irreparable damage to
the system.
ˎDo
ˎ not use a CD with tape, stickers or paste on it as this
may cause malfunction.
ˎWhen
ˎ
you remove a CD, do not touch the surface of the
disc.
Unit (back)
To change the play mode
Play mode enables you to playback the same
music repeatedly or shuffle-play.
Play mode
Selected track
or file number
Total playing time
of the selected
track or file
Repeat the steps above to program additional
tracks or files.
4 Press  .
Your program of tracks or files starts playback.
To cancel program play
In step 1, select “NORMAL” for “PROGRAM,” then
press .
To delete a programmed track or file
Press CLEAR  while the play is stopped. Each
time you press the button, the last programmed
track or file will be deleted.
When all the programmed tracks or files are
deleted, “NO STEP” appears.
Tip
ˎUp
ˎ to 25 tracks or files can be programmed. If you attempt
to program more than 25 tracks or files, “FULL” will be
displayed. In this case, delete unnecessary tracks.
ˎTo
ˎ play the same program again, press  .
Note
1 Press   to stop playback.
If you select “REPEAT” in step 4, you do not
have to stop playback.
2 Press MENU .
3 Press /  to select “CD MENU”, then press
.

(USB) port
Connect a USB device.
Note
ˎYou
ˎ
can use your iPhone/iPod with this system via
Bluetooth or connection only.
 AUDIO IN (external input) jack
Connect optional external equipment with an
audio connecting cable (not supplied).
 ~ AC IN input
Connect the power cord (supplied) to the wall
outlet.
 FM ANTENNA
Connect the FM antenna.
Note
ˎFind
ˎ
a location and an orientation that provide good
reception, and then fix the antennas to a stable surface
(window, wall, etc.).
ˎSecure
ˎ
the end of the FM lead antenna with adhesive
tape.
Setting the clock
5 Press /  to select the play mode, then
1 Press FUNCTION  to select “FM”.
2 Press and hold PRESET +/–  until the
PLAYMODE
3
4 Press /  to set the minutes, then press
.
.
Play mode
NORMAL
FOLDER*
Note
ˎThe
ˎ
clock settings are reset when you disconnect the
power cord or if a power failure occurs.
SHUFFLE
To display the clock when the system is off
Press DISPLAY  repeatedly to display the clock.
The clock is displayed for about 8 seconds.
If the system is in BLUETOOTH Standby mode,
the clock does not appear by pressing DISPLAY
.
Listening to the radio
Tuning in a radio station
.
press .
You can select the following play modes.
If “PLAY SET” is displayed, press /  to
select “CLOCK,” then press .
ˎWhen
ˎ
the disc is ejected or the power cord is
disconnected after programming, all the programmed
tracks and files are deleted.
4 Press /  to select “PLAYMODE” or
“REPEAT,” then press
1 Press   to turn on the system.
2 Press TIMER .
Press /  to set the hour, then press
Playing a file on a USB device
You can play audio files stored on a USB device
such as WALKMAN® or digital media player, on
this system by connecting a USB device to the
system.
For details on compatible USB devices, see
“Compatible devices and versions.”
1 Press FUNCTION  to select “USB.”
2 Connect the USB device to the
(USB) port
 on the rear of the unit.
Connect the USB device directly, or via the USB
cable supplied with the USB device, to the
(USB) port .
Wait until “READING” disappears.
.
 (eject) 
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency
(RF) Exposure Guidelines. This equipment has
very low levels of RF energy that it deemed to
comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator
at least 20 cm or more away from person’s body
(excluding extremities: hands, wrists, feet and
ankles).
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment
has very low levels of RF energy that it deemed
to comply without maximum permissive
exposure evaluation (MPE). But it is desirable
that it should be installed and operated keeping
the radiator at least 20 cm or more away from
person’s body (excluding extremities:hands,
wrists, feet and ankles).
Creating your own program
(Program Play)
Listening to a file on a USB
device
3 Press /  to select a desired track or
Front
This equipment must not be co-located or
operated in conjunction with any other antenna
or transmitter.
This device complies with industry Canada
licence-exempt RSS standard(S).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may
cause undesired operation of the device.
ˎCompatibility
ˎ
with all MP3 encoding/writing software,
CD-R/RW drive and recording media cannot be
guaranteed. Incompatible MP3 discs may produce noise or
interrupted audio or may not play at all.
FLDR.SHUF*
PROGRAM
Effect
Plays a track or file.
Plays all tracks in the selected
folder. “FLDR” lights up in the
display window .
Plays all tracks or files in
random order. “SHUF” lights
up in the display window .
Plays all tracks or files in the
selected folder in random
order. “FLDR. SHUF” lights up
in the display window .
Plays the programmed tracks
or files. “PGM” lights
up in the display window .
For details, see “Creating your
own program (Program Play)”.
* This play mode is applicable only for playing an MP3 disc.
Play mode
Effect
ALL (Repeat
plays all tracks)
The system plays all tracks in a
disc or folder repeatedly.
“ ” lights up in the display
window .
The system plays the selected
track repeatedly. “ 1” lights
up in the display window .
Cancels repeat playback.
OFF
Manual tuning
Press PRESET +/–  repeatedly to tune-in the
desired station.
Tip
ˎIf
ˎ reception of an FM stereo broadcast is noisy, press MENU
 and select “TUNE:MENU,” “FM MODE” and “MONO” in
turn, to select monaural reception. This reduces noise.
Presetting radio stations
You can preset your desired radio stations.
1 Tune in the desired station, then press MENU
.
2 Press /  to select “TUNE:MENU,” then
press
.
3 Press /  to select “MEMORY,” then press
.
REPEAT
ONE (Repeat
plays one track)
frequency indication in the display window 
starts changing, then release the button.
Tuning stops automatically when a FM stereo
broadcast is received (Automatic Scanning).
“ST” lights up in the display window .
Note on playing MP3 discs
ˎDo
ˎ not save unnecessary folders or files on a disc that has
MP3 files.
ˎFolders
ˎ
that have no MP3 files are not recognized on the
system.
ˎThe
ˎ
system can only play MP3 files that have a file
extension of “.mp3.”
Even when file name has the “.mp3” file extension, if it is
not an audio MP3 file, playing this file may generate a loud
noise, which could cause damage of the system.
ˎThe
ˎ
maximum number of MP3 folders and files compatible
with this system is:
999* folders (including the root folder)
999 files
250 files in a single folder
8 folder levels (in the tree structure of files)
* This include folders that have no MP3 or other files. The
number of folders that the system can recognize may
be less than actual number of folders, depending on the
folder structure.
4 Press /  to select “OK,” then press .
5 Press /  to select the preset number,
then press
.
Preset number
“COMPLETE” appears in the display window
 and the radio station is registered with the
preset number.
Repeat the steps above to register further
radio stations.
6 Press /  to turn off the power, then press
/  again to turn on the power.
Tip
ˎYou
ˎ
can preset up to 20 FM stations.
ˎIf
ˎ you select an already-registered preset number in step
5, the preset radio station is replaced by the currently
tuned-in radio station.
To tune in to a preset radio station
Press PRESET +/–  to select the preset number
to which the desired station is registered.
3 Press  .
Starts playback.
You can operate fast-rewind/fast-forward,
selecting a track or file or selecting folder with
the remote or the button of the unit.
To change the play mode
Listening to music through
a BLUETOOTH connection
Pairing the system with a
BLUETOOTH device and listening
to music
You can listen to music from BLUETOOTH device
over a wireless connection.
Before using the BLUETOOTH function, perform
pairing to register your BLUETOOTH device.
Note
ˎPlace
ˎ
the BLUETOOTH device to be connected within one
meter of the system.
ˎIf
ˎ your BLUETOOTH device is compliant with touch (NFC),
skip the next procedure. See “Listening to music by onetouch action (NFC).”
1 Press FUNCTION  to select “BT AUDIO.”
2 Press MENU .
3 Press /  to select “BT MENU,” then press
.
4 Press /  to select “PAIRING,” then press
.
5 Press /  to select “OK” then press
.
When “PAIRING” starts flashing in the display
window , the system changes to pairing
mode.
When playing the USB device, the play mode
can be selected. Press MENU , then select
“USB MENU.” Select “PLAYMODE” or “REPEAT.”
For details, see “To change the play mode” of
“Listening to a CD.” When a file on a USB device
is playing, programmed playback cannot be
played.
6 Search for this system with the BLUETOOTH
Tip
7 Select [SONY:CMT-X5CD] (this system).
ˎIf
ˎ a USB device is connected to the unit, battery charging
starts automatically. Even when the system is off, the USB
device can be charged.
ˎIf
ˎ the USB device cannot be charged, disconnect and
reconnect it. For details on the charging status of the USB
device, see the operating manual of the USB device.
Note
ˎThe
ˎ
playback order for the system may differ from the
playback order of the connected digital music player.
ˎBe
ˎ sure to turn off the system before removing the USB
device. Removing the USB device while the system is
turned on may corrupt the data on the USB device.
ˎWhen
ˎ
USB cable connection is necessary, connect the
USB cable supplied with the USB device to be connected.
For details on connection, refer to the operation manual
supplied with the USB device to be connected.
ˎIt
ˎ may take time before “READING” appears after
connecting, depending on the type of USB device
connected.
ˎDo
ˎ not connect the USB device through a USB hub.
ˎWhen
ˎ
the USB device is connected, the system reads all
the files on the USB device. If there are many folders or
files on the USB device, it may take a long time to finish
reading the USB device.
ˎWith
ˎ
some connected USB devices, it may take a long time
to transmit signals from the system or to finish reading the
USB device.
ˎCompatibility
ˎ
with all encoding/writing software cannot
be guaranteed. If audio files on the USB device were
originally encoded with incompatible software, those files
may produce noise or, may malfunction.
ˎThe
ˎ
maximum number of folders and files on the USB
device compatible with this system is:
1,000* folders (including the root folder)
3,000 files
250 files in a single folder
8 folder levels (in the tree structure of files)
* This includes folders that have no playable audio file and
empty folders. The number of folders that the system
can recognize may be less than actual number of folders,
depending on the folder structure.
ˎThe
ˎ
system does not necessarily support all the functions
provided in a connected USB device.
that have no audio files are not recognized.
ˎFolders
ˎ
ˎThe
ˎ
audio formats that you can listen to with this system
are as follows:
MP3: file extension “.mp3”
WMA*: file extension “.wma”
AAC*: file extension “.m4a,” “mp4” or “.3gp”
Note that even when file name has the correct file
extension, if the actual file differs, the system may
produce noise or may malfunction.
* Files with DRM (Digital Rights Management) copyright
protection or files downloaded from an online music
store cannot be played on this system. If you try to play
one of these files, the system plays the next unprotected
audio file.
Listening to music with
optional audio components
Playing back the music of
optional audio components
You can play a track of optional audio
components connected to the unit.
Note
ˎBeforehand,
ˎ
press the VOL –  to turn down the volume.
1 Press FUNCTION  to select “AUDIO IN.”
2 Connect its audio connecting cord to the
AUDIO IN jack  on the rear of the unit and
the output terminal of the optional external
equipment.
3 Start playback of the connected component.
Adjust the volume on the connected
component during playback.
4
Press VOL +/  on the remote to adjust the
volume.
Note
ˎThe
ˎ
system may enter Standby mode automatically if the
volume level of the connected component is too low. For
details, see “Setting the Automatic Standby function.”
device.
A list of the devices found may appear on the
BLUETOOTH device display.
If prompted to enter a passkey on the
BLUETOOTH device, enter “0000.”
If this system is not shown in the display of
the device, proceed from step 1 again.
When pairing is completed, the display
changes to the connected BLUETOOTH device
name from “PAIRING” and the BLUETOOTH
indicator lights up.
8 Press  .
Starts playback.
Depending on the BLUETOOTH device, press
  again. Also, you may have to start up a
music player on the BLUETOOTH device.
9 Press VOL +/–  to adjust the volume.
If the volume cannot be changed on the
system, adjust it on your BLUETOOTH device.
Operation such as fast-rewind/fast-forward,
selecting music and selecting a folder can be
operated with the remote or buttons of the
unit.
Tip
ˎYou
ˎ
can perform a pairing operation or attempt to make a
BLUETOOTH connection with another BLUETOOTH device
while the BLUETOOTH connection is established with one
BLUETOOTH device. The currently established BLUETOOTH
connection is canceled when BLUETOOTH connection with
another device is successfully established.
Note
ˎThe
ˎ
operations described above may not be available
for certain BLUETOOTH devices. In addition, the actual
operations may differ depending on the connected
BLUETOOTH device.
ˎOnce
ˎ
a pairing operation is performed, it does not have
to be performed again. In the following cases, however, a
pairing operation must be performed again:
Pairing information was erased when the BLUETOOTH
device was repaired.
You attempt to pair the system with more than 10
BLUETOOTH devices.
This system can pair with up to 9 BLUETOOTH devices.
If you pair another BLUETOOTH device after pairing
with 9 devices was performed, pairing information of
the device that was connected with the system first is
overwritten with that of the new device.
Pairing registration information of this system is erased
from the connected device.
If you initialize the system or erase the pairing history
with the system, all the pairing information will be
erased.
ˎThe
ˎ
sound of this system cannot be sent to a BLUETOOTH
speaker.
ˎ“Passkey”
ˎ
may be called “Passcode,” “PIN code,” “PIN
number” or “Password,” etc.
To check the address of a connected
BLUETOOTH device
Press DISPLAY , while the name set on the
connected BLUETOOTH device is shown in the
display window . The BLUETOOTH device
address appears in two lines on the system
display window  for 8 seconds.
To cancel the connection with a
BLUETOOTH device
Disconnect the BLUETOOTH connection on the
BLUETOOTH device. “BT AUDIO” appears in the
display window .
To erase the pairing registration
information
1 Select “DEL LINK” after step 3 on “Pairing
the system with a BLUETOOTH device and
listening to music,” then press .
2 Press /  to select “OK,” then press
.
“COMPLETE” appears in the display window
 and all the pairing information is erased.
Note
ˎIf
ˎ you have erased the pairing information, you cannot
make a BLUETOOTH connection unless pairing is
performed again.
Listening to music through a
registered device
Note
After step 1 on “Pairing the system with a
BLUETOOTH device and listening to music,”
operate the BLUETOOTH device to connect with
the system, then press   of the unit to start
playback.
Listening to music by one-touch
action (NFC)
NFC is a technology for short-range wireless
communication between various devices such as
a mobile phone and IC tag.
Just touch your smartphone/tablet on the
system. The system is turned on automatically,
and pairing and BLUETOOTH connection are
established.
Beforehand, turn the NFC settings to on.
1 Touch your smartphone/tablet on the N-mark
 on the unit.
Touch the smartphone/tablet on the unit and
maintain contact until the smartphone/tablet
vibrates.
Refer to the user’s guide of your smartphone
for the part of your smartphone/tablet used
as touch contact.
2 After completing the connection, press  .
Starts playback.
To disconnect the established connection,
touch your smartphone/tablet on the N-Mark
 on the unit.
ˎThe
ˎ
Automatic Standby function is invalid for the tuner
function (FM), even when you have enabled it.
ˎThe
ˎ
system may not enter Standby mode automatically in
the following cases:
while using the FM function
while an audio signal is being detected
during playback of audio tracks or files
while the Play Timer or Sleep Timer is being used
ˎThe
ˎ
system counts down the time (about 15 minutes)
again until it enters Standby mode, even when Automatic
Standby function is enabled in the following cases:
when a USB device is connected while “USB” function
when a button on the remote or unit is pressed
Setting the BLUETOOTH Standby
mode
Note
Playing with high quality sound
codec (AAC/aptX)
You can receive the data in AAC or aptX codec
format from a BLUETOOTH device. It provides the
playback with a higher quality sound.
The factory settings of “BT AAC” and “BT APTX”
are “ON.”
1 Press MENU .
2 Press /  to select “BT MENU,” then press
.
3 Press /  to select “BT AAC” (AAC codec)
or “BT APTX” (aptX codec), then press
.
4 Press /  to select “ON,” then press
ˎIf
ˎ you initiate setup during BLUETOOTH connection, the
connection is cut.
ˎIf
ˎ sound is interrupted during reception in AAC codec
format, set to “OFF” in step 4 to cancel the settings. In this
case, the system receives SBC codec.
Additional information
Setting the Automatic Standby
function
The system enters Standby mode automatically
in about 15 minutes when there is no operation
or audio signal output (Automatic Standby
function).
By default, the Automatic Standby function is
turned on.
1 Press MENU .
2 Press /  to select “STBY:MODE,” then
.
3 Press /  to select “AUTO:STBY,” then press
.
4
Press /  to select “ON” or “OFF,” then
press
Tip
1 Prepare the sound source.
2 Press TIMER .
3 Press /  to select “PLAYTIMER,” then
press .
The start time flashes in the display window
.
5 Press /  to select the desired sound
press
.
3 Press /  to select “BT STBY,” then press
.
4 Press /  to select “ON” or “OFF,” then
press
.
5 Press /  to turn off the system.
Tip
ˎWhen
ˎ
this system is set to “ON,” the system turns on
automatically and you can listen to music by activating
BLUETOOTH on the connected component.
Setting the wireless
BLUETOOTH signal ON/OFF
When the unit is turned on, you can control a
BLUETOOTH signal. The default setting is ON.
1 Turn on the unit.
2 Press and hold   and /  of the unit.
3 After “RF OFF” (wireless BLUETOOTH signal is
ˎWhen
ˎ
this setting is set to OFF, the BLUETOOTH function is
not available.
ˎWhen
ˎ
this setting is off, the unit is turned on by the
smartphone/tablet by one-touch action (NFC) on the unit.
ˎWhen
ˎ
this setting is off, the BLUETOOTH Standby mode
cannot be set.
ˎWhen
ˎ
the BLUETOOTH Standby mode is on and the unit is
turned off, the BLUETOOTH Standby mode turns off.
ˎWhen
ˎ
this setting is off, the unit and BLUETOOTH device
cannot be paired.
ˎEven
ˎ
when this setting is off, a wired connection can still
be used.
Adjusting the sound
You can set the bass and treble or adjust the
tone to your preferences.
1 Press SOUND .
2 Press /  to select “CA+,” “P-EQ” (sound
effect), or “WIDE ST” (stereo effect), then press
.
CA+: Set to the recommended sound quality of
Sony.
P-EQ (EQUALIZER): Select the desired sound
from the following styles:
“R AND B/HIP HOP,” “ROCK,” “POPS,”
“CLASSIC,” “JAZZ,” “FLAT,” “CUSTOM”
WIDE ST (WIDE STEREO): Select “HIGH” or
“NORMAL,” then press . If you want to
adjust to a more natural stereo sound, select
“NORMAL.”
.
Follow the same procedure to set “MINUTE” of
the time to start operation, then “HOUR” and
“MINUTE” of the time to stop the operation.
.
ˎ2
ˎ minutes before entering standby mode, “AUTO:STBY”
displays in the display window .
About “SongPal”
A dedicated App for this model is available on
both Google Play™ and the App Store.
Sound settings
You can easily customize your sound, or use
Sony’s recommended settings “CA+.”
Controlling a CD inserted in the unit, or a
device connected via USB
You can play a CD that is inserted in the unit
or music in a device connected to the USB
connector.
What you can control with “SongPal” varies
depending on the connected device.
The specification and design of the app may
change without notice.
Device Select
Select a “SongPal” compatible device.
source, then press .
The confirmation display for the Play Timer
appears.
6 Press /  to turn off the system.
Note
ˎThe
ˎ
Play Timer does not work if the system is already on at
the preset time. Be careful not to operate the system until
it is turned on and starts play with the timer.
ˎWhen
ˎ
the sound source for a Play Timer is set to a radio
station that you set using Automatic
Scanning (AUTO) or Manual Tuning (MANUAL), and you
change the radio frequency or band after setting the
timer, the radio station setting for the timer will also be
changed.
ˎWhen
ˎ
the sound source for a Play Timer is set to a radio
station tuned from a preset radio station, and you change
the frequency of the radio station or band after setting
the timer, the radio station setting for the timer will not
change. The radio station tuning for the timer is fixed at
the frequency you set.
.
press
4 Press /  to select “PLAY SEL,” and then
press .
The timer setting appears in the display
window .
To cancel the timer
After step 3 on “To check the setting,” select
“OFF,” then press .
Changing the battery
The working distance of the remote shortens
as the battery becomes exhausted. When the
remote no longer operates the unit, replace the
battery with a new CR2025 lithium battery (not
supplied).
1 Push and hold  at the rear of the remote,
then pull out the battery holder in the
direction of the arrow.
Settings of the connected device
Various sound settings are displayed.
This menu can be displayed from any
screen by flicking right.
Home screen
Displays functions of selected
device, and apps installed on your
smartphone/iPhone.
The system offers Sleep Timer and Play Timer.
Mini player
Controller for selected function.
Troubleshooting
Troubleshooting
1 Make sure the power cord is firmly connected.
2 Find your problem in the checklist below, and
take the indicated corrective action.
If the issue persists, contact your nearest Sony
dealer.
If the standby indicator  flashes
Immediately unplug the power cord, and
make sure the power cord is not connected to
a wall outlet other than AC 120 V.
ˎˎAfter the standby indicator  stops
flashing, plug the power cord again, and
turn on the system. If the issue persists,
contact your nearest Sony dealer.
ˎˎMake sure you have connected the power cord
to a wall outlet correctly.
then insert the battery holder into the slot.
Note
Setting the Sleep Timer
At the specified time, the system is turned off
automatically.
1 Press MENU .
2 Press /  to select “SLEEP,” then press
.
3 Press /  to select the specified time, then
press .
You can select from “10MIN” (10 minutes) to
“90MIN” (90 minutes) in 10 minute increments.
Tip
ˎTo
ˎ check the remaining time of Sleep Timer, perform steps
1 and 2 above.
ˎThe
ˎ
Sleep Timer works even if the clock is not set.
To cancel the Sleep Timer
Select “OFF” in step 3 above.
Battery holder
Note
The system has entered Standby mode
unexpectedly.
ˎˎThis is not a malfunction. The system enters
Standby mode automatically in about 15
minutes when there is no operation or audio
signal output. See “Setting the Automatic
Standby function.”
+ facing up
ˎThe
ˎ
Sleep Timer has priority over the Play Timer.
ˎWipe
ˎ
the battery with a dry cloth to assure a good contact.
ˎDo
ˎ not hold the battery with metallic tweezers, otherwise
a short-circuit may occur.
ˎUse
ˎ
of batteries other than the CR2025 may cause a fire or
explosion.
“LOCKED” appears in the display window
 and the disc cannot be removed from
the disc slot .
ˎˎConsult your nearest Sony dealer or local
authorized Sony service facility.
The disc or file will not play.
ˎˎThe disc that has not been finalized (a CD-R or
CD-RW disc to which data can be added).
The sound skips, or the disc will not play.
ˎˎThe disc may be dirty or scratched. When the
disc is dirty, wipe it clean.
ˎˎMove the system to a location away from
vibration (for example, on top of a stable
stand).
ˎˎThe following discs can increase the time it
takes to start playback:
a disc recorded with a complicated tree
structure.
a disc recorded in multi-session format.
a disc that has many folders.
USB device
An unsupported USB device is connected.
General
2 Replace the battery with the“+” facing up,
CD-DA/MP3 disc
For details on compatible USB devices, see
“Compatible devices and versions.”
The system does not turn on.
Using the timers
ˎˎMake sure the USB device is connected securely
to the
(USB) port .
ˎˎThe USB device may not be supported by this
system.
ˎˎDisconnect the USB device and then reconnect
it. For details on the charging status of the USB
device, see the operating manual of the USB
device.
Starting playback takes more time than
usual.
3 Press /  to select “TIMER SEL,” and then
.
The USB device cannot be charged.
ˎˎMake sure the current play mode is correct. If
the play mode is “SHUFFLE” or “PROGRAM,”
change the setting.
To check the setting
1 Press TIMER .
2 Press /  to select “SELECT”, then press
The remote does not function.
ˎˎRemove any obstacles between the remote
and the remote sensor  on the unit, and
position the unit away from fluorescent lights.
ˎˎPoint the remote at the remote sensor  on
the unit.
ˎˎMove the remote closer to the system.
ˎˎReplace the batteries.
Play does not start from the first track or
file.
Tip
ˎBefore
ˎ
the preset time, the system automatically turns on.
for FM: about 15 seconds before the preset time
for a CD or USB device: about 90 seconds before the
preset time
ˎWhen
ˎ
the sound source is a CD, you can preprogram the
Play Timer. See “Creating your own program (Program
Play)”.
ˎWhen
ˎ
the sound source is radio, make sure to tune-in the
radio station in advance.
ˎTo
ˎ change the timer setting, perform the procedures from
the beginning again.
.
Note
press
You can listen to a CD or MP3 disc, USB device or
radio every day at a preset time.
The Play Timer setting remains as long as the
setting is not canceled.
1 Press MENU .
2 Press /  to select “STBY:MODE,” then
Tip
ˎIn
ˎ some countries and regions, NFC-compliant application
may not be downloaded.
ˎFor
ˎ some smartphones/tablets, this function may be
available without downloading “NFC Easy Connect.” In this
case, the operation and specifications of the smartphone/
tablet may be different from the description in this
manual.
For details, refer to the user’s guide supplied with your
smartphone/tablet.
Play timer
4 Press /  to select time, then press
off) or “RF ON” (wireless BLUETOOTH signal is
on) appears, release the button.
ˎWhen
ˎ
you touch an NFC-compliant smartphone/tablet on
the unit while another BLUETOOTH device is connected
with this system, the BLUETOOTH device is disconnected
and the system is connected with the smartphone/tablet.
Note
ˎMake
ˎ
sure you have set the clock before setting the timer.
See “Setting the clock.”
When BLUETOOTH Standby mode is enabled,
the system enters Wait mode for BLUETOOTH
connection even when the system is turned off.
This mode is disabled by default.
Tip
ˎCompatible
ˎ
smartphones are those equipped with the NFC
function (compatible operating system: Android version
2.3.3 or later with the exception of Android 3.x).
Check the website below for information on compatible
devices.
For customers in the United States:
http://esupport.sony.com/
For customers in Canada
http://esupport.sony.com/CA/
ˎIf
ˎ the smartphone/tablet does not respond even though
it is touched to the unit, download “NFC Easy Connect”
to your smartphone/tablet and run it. Then touch to the
unit again. “NFC Easy Connect” is a free application for
exclusive use with Android™. Scan the following 2D Code.
Setting the Play Timer
The clock setting or the Play Timer
operation has been canceled
unexpectedly.
ˎˎIf about a minute elapses with no operation,
the clock setting or Play Timer setting is
canceled automatically. Perform the operation
again from the beginning.
There is no sound.
ˎˎTurn up the volume on the unit.
ˎˎMake sure an external component is connected
correctly to the AUDIO IN jack  and set the
function to AUDIO IN.
ˎˎThe specified station may have temporarily
stopped broadcast.
Severe hum or noise occurs.
ˎˎMove the system away from sources of noise.
ˎˎConnect the system to a different wall outlet.
ˎˎUse of an AC power tap with a noise filter (not
supplied) is recommended.
ˎˎThe following problems may occur.
The USB device is not recognized.
File or folder names are not displayed on this
system.
Playback is not possible.
The sound skips.
There is noise.
A distorted sound is output.
There is no sound.
ˎˎThe USB device is not connected correctly. Turn
off the system, and then reconnect the USB
device.
There is noise, skipping, or distorted
sound.
ˎˎAn unsupported USB device is connected.
Connect a supported USB device.
ˎˎTurn off the system, then reconnect the USB
device and turn on the system.
ˎˎThe music data itself contains noise, or the
sound is distorted. Noise may have been
entered when creating music data due to the
conditions of the computer. In this case, delete
the file and send the music data again.
ˎˎThe bit rate used when encoding the files was
low. Send files encoded with higher bit rates to
the USB device.
“READING” is displayed for an extended
time, or it takes a long time before
playback starts.
ˎˎThe reading process may take a long time in
the following cases.
There are many folders or files on the USB
device.
The file structure is extremely complex.
Not enough free space in the memory.
The internal memory is fragmented.
The file or folder name (album name) is
not displayed correctly.
ˎˎSend the music data to the USB device again,
as the data stored in the USB device may have
been corrupted.
ˎˎThe character code that can be displayed by
this system are as follows:
Upper cases (A to Z).
Numbers (0 to 9).
Symbols (< > * +, [ ] @ \ _).
Other characters appear as “_.”
The USB device is not recognized.
ˎˎTurn off the system and reconnect the USB
device, then turn on the system.
ˎˎAn incompatible USB device may be connected.
ˎˎThe USB device does not work properly. Refer
to the operating manual supplied with the USB
device for how to deal with this problem.
Play does not start.
ˎˎTurn off the system and reconnect the USB
device, then turn on the system.
ˎˎAn incompatible USB device may be connected.
Play does not start from the first track.
ˎˎSet the play mode to “NORMAL” play mode.
Tuner
Severe hum or noise occurs (“STEREO”
flashes in the display window ), or
broadcasts cannot be received.
ˎˎConnect the antenna properly.
ˎˎFind a location and an orientation that provide
good reception, and then set up the antenna
again.
ˎˎKeep the antennas away from the unit, speaker
cord or other AV components to avoid picking
up noise.
ˎˎTurn off nearby electrical equipment.
Several radio stations can be heard at the
same time.
ˎˎFind a location and an orientation that provide
good reception, and then set up the antenna
again.
ˎˎBundle the antenna cables using commercially
available cord clips and adjust the cable
lengths.
To reset the system to factory settings
If the system still does not operate properly,
reset the system to factory settings.
Use buttons on the unit to reset the system to its
factory default settings.
1 Disconnect the power cord and confirm
that the standby indicator  is not lit. Then
reconnect the power cord and turn on the
system.
2 Press and hold FUNCTION  and /  on
the unit until “RESET” appears in the display.
All user-configured settings, such as preset
radio stations, timer, and the clock, are
deleted.
If the problem persists after doing all of the
above, consult your nearest Sony dealer.
Note
ˎIf
ˎ you dispose of the unit or give it to another person,
reset the unit for security.
Messages
The following messages may appear or flash
during operation.
CAN’T PLAY: You have set a disc that cannot be
played back on this system, such as CD-ROM
and DVD disc.
COMPLETE: The station preset operation ended
normally.
DATA ERROR: You tried to play an unplayable
file.
ERROR: You operated the system during
initialization. Wait for a while until the
initialization is completed.
FULL: You tried to program more than 25 tracks
or files.
LOCKED: The disc slot  is locked and you
cannot remove the disc. Contact your nearest
Sony dealer.
NO DEVICE: No USB device is connected or the
connected USB device has been removed.
NO DISC: There is no disc in the player, or you
have loaded a disc that cannot be played.
NO MEMORY: The memory media is not
inserted in the USB device, or the system does
not identify the memory media.
NO STEP: All of the programmed tracks have
been erased.
NO SUPPORT: The system does not support the
connected USB device.
NO TRACK: There are not playable files on the
USB device or disc.
NOT IN USE: You pressed an unplayable button.
OVER CURRENT: Remove the USB device from
the port and turn off the system then turn on
the system.
PUSH STOP: You attempted to change the
play mode during playback in the CD or USB
function.
READING: The system is reading the information
on the CD or USB device. Some buttons do not
work during reading.
TIME NG: The Play Timer start and end times are
set to the same time.
Precautions/Specifications
Precautions
Discs that this system CAN play
ˎˎAudio CD-DA discs
ˎˎCD-R/CD-RW (audio data of CD-DA tracks and
MP3 files)
Do not use a CD-R/CD-RW disc with no data
stored. Doing so may damage the disc.
Discs that this system CANNOT play
ˎˎCD-ROM
ˎˎCD-R/CD-RW other than those recorded in
music CD format or MP3 format conforming to
ISO9660 Level 1/Level 2, Joliet
ˎˎCD-R/CD-RW recorded in multi-session format
and not closed the session
ˎˎCD-R/CD-RW of poor recording quality,
CD-R/CD‑RW that have scratches or are dirty,
or CD‑R/CD-RW recorded with an incompatible
recording device
ˎˎCD-R/CD-RW which is finalized incorrectly
ˎˎCD-R/CD-RW containing files other than MPEG
1 Audio Layer-3 (MP3) files
ˎˎ8 cm disc
ˎˎDiscs of non-standard shape (for example,
heart, square, star)
ˎˎDiscs that have adhesive tape, paper, or sticker
attached to them
ˎˎRental or used discs with attached seals where
the glue extends beyond the seal
ˎˎDiscs that have labels printed using ink that
feels tacky when touched
Notes on CD-DA discs
ˎˎBefore playing, wipe the disc with a cleaning
cloth from the center out to the edge.
ˎˎDo not clean discs with solvents, such as
benzine, thinner, or commercially available
cleaners or anti-static spray intended for vinyl
LPs.
ˎˎDo not expose discs to direct sunlight or heat
sources such as hot air ducts, nor leave it in a
car parked in direct sunlight.
On safety
ˎˎCompletely disconnect the power cord (mains
lead) from the wall outlet (mains) if it is not
going to be used for an extended period of
time. When unplugging the system, always grip
the plug. Never pull the cord itself.
ˎˎShould any solid object or liquid get into
the system, unplug the system, and have
it checked by qualified personnel before
operating it again.
ˎˎThe AC power cord can be changed only by a
qualified service facility.
On placement
ˎˎDo not place the system in an inclined position
or in locations that are extremely hot, cold,
dusty, dirty, or humid or lacking adequate
ventilation, or subject to vibration, direct
sunlight or a bright light.
ˎˎBe careful when placing the system on surfaces
that have been specially treated (for example,
with wax, oil, polish) as staining or discoloration
of the surface may result.
ˎˎIf the system is brought directly from a cold to
a warm location or is placed in a very damp
room, moisture may condense on the lens
inside the CD player, and cause the system
to malfunction. In this situation, remove the
disc, and leave the system turned on for about
an hour until the moisture evaporates. If the
system still does not operate, even after an
extended period, consult your nearest Sony
dealer.
On heat buildup
ˎˎHeat buildup on the unit during charging or
operation over a long period of time is normal
and not cause for alarm.
ˎˎDo not touch the cabinet if it has been used
continuously at a high volume because the
cabinet may have become hot.
ˎˎDo not obstruct the ventilation holes.
Cleaning the cabinet
Clean this system with a soft cloth slightly
moistened with a mild detergent solution. Do
not use any type of abrasive pads, scouring
powder, or solvents, such as thinner, benzine, or
alcohol.
Compatible devices and versions
iPhone/iPad/iPod touch
Check the websites below for details on the
latest supported versions of the compatible
devices:
For customers in the United States:
http://esupport.sony.com/
For customers in Canada
http://esupport.sony.com/CA/
Compatible models
Bluetooth®
iPhone 5s

iPhone 5c

iPhone 5

iPhone 4s

iPhone 4

iPhone 3GS

iPad Air *

iPad mini with Retina display*

iPad (4th generation)*

iPad mini*

iPad (3rd generation)*

iPad 2*

iPad*

iPod touch (5th generation)

iPod touch (4th generation)

iPod touch (3rd generation)*

iPod nano (7th generation)*

* “SongPal” does not support iPod touch (3rd generation),
iPod classic, and iPod nano.
“SongPal” does not support iPad as of January 2014.
Bluetooth technology works with iPhone 5s,
iPhone 5c, iPhone 5, iPhone 4s, iPhone 4, iPhone
3GS, iPod touch (5th generation), iPod touch (4th
generation).
USB device
Check the websites below for details on the
latest supported versions of the compatible
devices:
For customers in the United States:
http://esupport.sony.com/
For customers in Canada
http://esupport.sony.com/CA/
BLUETOOTH wireless technology
BLUETOOTH wireless technology is a short-range
wireless technology linking digital devices, such
as personal computers and digital still cameras.
Using the BLUETOOTH wireless technology, you
can operate the units involved within a range of
about 10 meters.
The BLUETOOTH wireless technology is
commonly used between two devices, but a
single device can be connected to multiple
devices.
You do not need wires to get connected as you
do with a USB connection, and you do not need
to place the devices face to face as you do with
wireless infrared technology. You can use the
technology with one BLUETOOTH device in your
bag or pocket.
BLUETOOTH wireless technology is a global
standard supported by thousands of companies.
These companies produce products that meet
the global standard.
Supported BLUETOOTH version and
profiles
Profile refers to a standard set of capabilities for
various BLUETOOTH product capabilities. See
“Specifications” for details on the supported
BLUETOOTH version and profiles.
Note
ˎTo
ˎ use a BLUETOOTH device connected to this system,
the device must support the same profile as this system.
Note that the functions of the BLUETOOTH device may be
different depending on the specifications of the device,
even if it has the same profile as this system.
of the properties of BLUETOOTH wireless
ˎBecause
ˎ
technology, playback on this system is slightly delayed
compared with audio playback on the transmitting device.
Effective communication range
BLUETOOTH devices should be used within
approximately 10 meters (unobstructed distance)
of each other. The effective communication
range may become shorter under the following
conditions.
When a person, metal object, wall or other
obstruction is between the devices with a
BLUETOOTH connection
Locations where a wireless LAN is installed
Around microwave ovens that are in use
Locations where other electromagnetic
waves occur
Effects of other devices
BLUETOOTH devices and wireless LAN (IEEE
802.11b/g) use the same frequency band (2.4
GHz). When using your BLUETOOTH device
near a device with wireless LAN capability,
electromagnetic interference may occur. This
could result in lower data transfer rates, noise,
or inability to connect. If this happens, try the
following remedies:
Try connecting this system and BLUETOOTH
mobile phone or BLUETOOTH device when
you are at least 10 meters away from the
wireless LAN equipment.
Turn off the power to the wireless LAN
equipment when using your BLUETOOTH
device within 10 meters.
Effects on other devices
The radio waves broadcast by this system may
interfere with the operation of some medical
devices. Since this interference may result in
malfunction, always turn off the power on
this system, BLUETOOTH mobile phone and
BLUETOOTH device in the following locations:
In hospitals, on trains, and in airplanes
Near automatic doors or fire alarms
Note
ˎThis
ˎ
system supports security functions that comply with
the BLUETOOTH specification as a means of ensuring
security during communication using BLUETOOTH
technology. However, this security may be insufficient
depending on the setting contents and other factors, so
always be careful when performing communication using
BLUETOOTH technology.
ˎSony
ˎ
cannot be held liable in any way for damages
or other loss resulting from information leaks during
communication using BLUETOOTH technology.
ˎBLUETOOTH
ˎ
communication is not necessarily guaranteed
with all BLUETOOTH devices that have the same profile as
this system.
devices connected with this system must
ˎBLUETOOTH
ˎ
comply with the BLUETOOTH specification prescribed
by the BLUETOOTH SIG, Inc., and must be certified to
comply. However, even when a device complies with the
BLUETOOTH specification, there may be cases where the
characteristics or specifications of the BLUETOOTH device
make it impossible to connect, or may result in different
control methods, display or operation.
ˎNoise
ˎ
may occur or the audio may cut off depending on
the BLUETOOTH device connected with this system, the
communications environment, or surrounding conditions.
Specifications
Amplifier section
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(The United States model only)
With 8 ohm loads, both channels driven, from
120 - 10,000 Hz; rated 12 watts per channel
minimum RMS power, with no more than 0.7%
total harmonic distortion from 250 milliwatts to
rated output.
Power output (rated): 16 watts + 16 watts
(at 8 ohms, 1 kHz, 1% THD)
RMS power output (reference): 20 watts +
20 watts (per channel at 8 ohms, 1 kHz)
Inputs/Outputs
AUDIO IN (external input) jack:
Stereo mini jack, sensitivity 700 mV, impedance
47 kilohms
USB:
USB port: Type A, 5 V DC 1.5 A
CD-DA/MP3 player section
System: Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6 µW
*This output is the value measurement at a
distance of 200mm from the objective lens
surface on the Optical Pick-up Block with 7mm
aperture.
Frequency response: 20 Hz – 20 kHz
Signal-to-noise ratio: More than 90 dB
Dynamic range: More than 90 dB
Tuner section
FM tuner section:
FM stereo, FM superheterodyne tuner
Tuning range: 87.5 MHz – 108.0 MHz (100 kHz
step)
Antenna: FM lead antenna
Antenna terminals:
75 ohms unbalanced
Speaker section
Speaker system:
Full-range speaker
Passive radiator
Rated impedance: 8 ohms
BLUETOOTH section
Communication system:
BLUETOOTH Standard version 3.0
Output:
BLUETOOTH Standard Power Class 2
Maximum communication range:
Line of sight approx. 10 m*1
Frequency band:
2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Modulation method:
FHSS
Compatible BLUETOOTH profiles*2:
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
Supported content protection method:
SCMS-T method
Supported codec:
SBC (Sub Band Codec), AAC, aptX
Transmission bandwidth:
20 Hz – 20,000 Hz (with 44.1 kHz sampling)
The actual range will vary depending on
factors such as obstacles between devices,
magnetic fields around a microwave oven,
static electricity, reception sensitivity,
antenna’s performance, operating system,
software application, etc.
*2
BLUETOOTH standard profiles indicate the
purpose of BLUETOOTH communication
between devices.
*1
General
Power requirements:
AC 120 V, 60 Hz
Power consumption: 24 watts
Dimensions (W/H/D) (incl. projecting parts):
Approx. 385 mm × 178 mm × 81 mm
Mass: Approx. 2.7 kg
Supplied accessories: Remote (RM-AMU197) (1),
CR2025 lithium battery (1), AC power cord (1),
FM lead antenna (1), Operating Instructions (this
manual) (1)
Design and specifications are subject to change
without notice.
Standby power consumption:0.5 W (all wireless network
ports off)
Networked Standby mode:3 W (all wireless network ports
on)