EtherXtend DS3 Ethernet Access Device
ETHX-2214-DS3, ETHX-2224-DS3
EtherXtend DS3 Ethernet Access Device with up to 2
bonded DS3s and an integrated 4 port 10/100 switch
✓
Deliver Ethernet at speeds
up to 90 Mbps to
anywhere that can be
served by unframed /
unstructured DS3 circuits
✓
Automatic load balancing
and fail-over on bonded
ports for optimum
throughput and
redundancy
The EtherXtend 2200 Series of DS3 Ethernet Access Devices (EADs) allows Carriers,
ISPs and PTTs to deliver Ethernet services to virtually anywhere, using standard
unframed/unstructured DS3 circuits. These units permit the efficient and reliable
delivery of Ethernet on a single DS3 or on a bonded pair of DS3 circuits. With the
ability to provide up to 90 Mbps of data transport, near native 10/100BT Ethernet
✓
✓
✓
✓
Connects directly to any
RJ45 10/100 Mbps
Ethernet port via an
integrated 4-port switch
speeds can be achieved to deliver demanding LAN, WAN, and IP-based services to an
increasingly sophisticated generation of small and medium-sized business customers.
The EtherXtend 2200 Series of DS3 EADs can be deployed at any location that is served
by one or more unframed/unstructured DS3s; and because they use Ethernet instead of
ATM or Frame Relay, they are optimized for the delivery of high speed Internet
Provide sophisticated QoS
and application-aware
traffic control
Protocol (IP) traffic, including applications requiring high bandwidth, low latency
transport mechanisms such as video conferencing, digital video surveillance, IP
telephony and much more.
Full support for Zhone's
unique, Multimedia
Traffic Management
(MTM) capabilities
The EtherXtend 2200 Series of DS3 EADs feature an integrated 4-port 10/100 Ethernet
Environmentally hardened
and NEBS Level 1 Certified
To maximize the total bandwidth available, the ETHX-22x4-DS3 devices operate in a
switch and either one or two DS3 ports, each capable of delivering up to 45 Mbps of
bandwidth. On a 2-port device, the two DS3 ports can be bonded together to provide
90 Mbps data rates. The loop bonding technology used by the EtherXtend 2200 Series
DS3 EADs is the industry-leading, Net-to-Net (N2N) loop bonding protocol.
DS3 framer-bypass mode whereby the Ethernet traffic is mapped onto the entire 44.736
Mbps of each DS3 facility (including the overhead bits normally used for various DS3
✓
Flexible Management:
Web-based, CLI, and
SNMP
framing formats). Therefore, unframed DS3 circuits (rather than M13 or C-bit Parity
DS3 frame formats) are to be used with ETHX-22x4-DS3 network extenders, and any
intermediary DS3 transport or multiplexing equipment must be set to regenerate the
entire 44.736 Mbps of bandwidth without modifying or omitting any of the bits
typically associated with overhead in framed DS3 facilities. By combining unframed
DS3s with N2N loop bonding protocols, the ETHX-22x4 devices offer automatic,
efficient, resilient, and configuration-free deployment with greater total throughput
capacity than a traditional DS3 circuit.
The EtherXtend DS3 EADs also supports many advanced network features, including:
802.1Q VLANs, built-in security features, advanced QoS and sophisticated bandwidth
management and control features available only with Zhone's unique Multimedia
Traffic Management (MTM) capabilities.
EtherXtend DS3 Ethernet Access Device
Technical Specifications
Dimensions
■
■
1.9" High x 8.6" Wide x 6.75" Deep
4.8cm High x 21.7cm Wide x 17.1cm Deep
Weight
■
1.0 lbs (0.45 kg)
Power
Standards Support
■
■
■
■
■
■
NEBS Level 1
GR-063-CORE
GR-1089-CORE
IEEE 802.3 Ethernet
IEEE 802.1Q VLAN
IEEE 802.1p, DiffServ, TOS bit QoS
Bandwidth/Distance
■
Regulatory Compliance
■
■
Protocol Support
■
■
■
■
AC Operation: 100-240 VAC; 50-60 Hz
DC Operation: -36VDC to -72VDC
10 watts (single DS3 port)
15 watts (dual DS3 port)
Interfaces
■
■
ETHX-2214-DS3:
- One (1) DS3 (75 ohm BNC)
- Four (4) 10/100BT Ethernet (RJ45)
- One (1) COM port (RJ45)
ETHX-2224-DS3:
- Two (2) DS3s (75 ohm BNC)
- Four (4) 10/100BT Ethernet (RJ45)
- One (1) COM port (RJ45)
■
■
■
Transparent 802.1D Bridging
Internet Protocol
Loop Bonding
Management
■
■
EMC: FCC Part 15, ICES-003
Safety: ANSI/UL 60950-1, CAN/CSA C22.2,
IEC60950-1, EN60950-1
Operating Requirements
■
■
■
■
■
Up to 45 Mbps per DS3 port (up to 90 Mbps
loop bonded)
Temperature: -40ºF to 158ºF (-40ºC to 70ºC)
Non-operating:: -40ºF to 158ºF (-40ºC to 70ºC)
Humidity: 5% to 95%, non-condensing
Altitude: -200ft to 16,500ft (-60m to 5,000m)
SNMP
CLI
Web Based Management
Ordering Information
EtherXtend DS3 Ethernet Access Devices
ETHX-2214-DS3-DC
EtherXtend CPE, N2N, 1PRT DS3 WAN, 4PRT 10/100BT LAN, DC Power
ETHX-2214-DS3-US
EtherXtend CPE, N2N, 1PRT DS3 WAN, 4PRT 10/100BT LAN, AC Power w/US Plug
ETHX-2224-DS3-DC
EtherXtend CPE, N2N, 2PRT DS3 WAN, 4PRT 10/100BT LAN, DC Power
ETHX-2224-DS3-US
EtherXtend CPE, N2N, 2PRT DS3 WAN, 4PRT 10/100BT LAN, AC Power w/US Plug
Optional 19/23-inch Rack Mount Kit
NETEXT-RMT-KIT
NET EXT, RACK MOUNT TRAY, TNE15X4/ENE20X4, ETHX22X4/ETHX21XX, SNE2040G
2008/08/20 12:17:08
Download PDF