Intel® Server System SR1690WB
Service Guide
A Guide for Technically Qualified Assemblers of Intel® Identified Subassemblies/
Products
Intel Order Number E78186-004
Disclaimer
Information in this document is provided in connection with Intel® products. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's
Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any
express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to
fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property
right. Intel products are not designed, intended or authorized for use in any medical, life saving, or life sustaining
applications or for any other application in which the failure of the Intel product could create a situation where
personal injury or death may occur. Intel may make changes to specifications and product descriptions at any time,
without notice.
Intel server boards contain a number of high-density VLSI and power delivery components that need adequate
airflow for cooling. Intel's own chassis are designed and tested to meet the intended thermal requirements of these
components when the fully integrated system is used together. It is the responsibility of the system integrator that
chooses not to use Intel developed server building blocks to consult vendor datasheets and operating parameters to
determine the amount of airflow required for their specific application and environmental conditions. Intel Corporation
can not be held responsible if components fail or the server board does not operate correctly when used outside any
of their published operating or non-operating limits.
Intel, Intel Pentium, and Intel Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in
the United States and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2010, Intel Corporation. All Rights Reserved
ii
Intel® Server System SR1690WB Service Guide
Preface
About this Manual
Thank you for purchasing and using the Intel® Server System SR1690WB.
This manual is written for system technicians responsible for troubleshooting, upgrading,
and repairing this server board. This document provides a brief overview of the features of
the board/chassis, a list of accessories or other components you may need, troubleshooting
information, and instructions on how to add and replace components on the Intel® Server
System SR1690WB. For the latest version of this manual, see http://support.intel.com/
support/motherboards/server/S5500WB.
Manual Organization
Chapter 1 provides a list of reference resources. In this chapter, you will find a list of
technical documents that give additional details on the Intel® Server System SR1690WB,
and the location where they can be found.
Chapter 2 provides a brief overview of the Intel® Server System SR1690WB. In this
chapter, you will find a list of the server board features, photos and illustrations of the
product, and product diagrams to help you identify components and their locations.
Chapter 3 provides instructions on using the utilities that are shipped with the board or
that may be required to update the system. This includes how to navigate through the
BIOS Setup screens, how to perform a BIOS update, and how to reset the password or
CMOS. Information about the specific BIOS settings and screens available in the Intel®
Server System SR1690WB Technical Product Specification. See the “Server System
References” chapter for more information.
Chapter 4 provides instructions on adding and replacing components. Use this chapter for
step-by-step instructions and diagrams for installing or replacing components such as the
memory, processor, front panel board, and the battery, among other components.
The rest of this manual provides technical specifications, regulatory information, “Getting
Help” information, and the warranty.
iii
Product Contents
The Intel® Server System SR1690WB ships with the Intel® Server Board S5500WB. For
further information, see the following documents:
• Intel® Server Board S5500WB Technical Product Specification
• Intel® Server System SR1690WB Technical Product Specification
The contents of the server system are listed below.
Intel® Server System SR1690WB - Product Contents
Your Intel® Server System SR1690WB ships with the following items:
•
•
•
•
•
Intel® Server Board S5500WB, installed in the server system
•
•
•
•
•
•
Four hot-swap HDD carriers, installed in the server system
Chassis master assembly with single 650W high-efficiency power supply unit
One PCI Express* riser card assembly, installed in the server system
Four system fan blowers, installed in the server system
Standard control panel module and cables (I/O and USB), installed in the server
system
System air duct, installed in the server system
Attention document, in the server system product box
Quick Start User's Guide, in the server system product box
Intel® Server Deployment Toolkit 3.0 CD
Hardware accessary bag, described as below:
— Optical drive latch assembly
— Optical drive SATA/Power cable
— Rack handles
— One SES cable
— Various types of screws
— Two STS-100P processor heatsinks for 1U rack chassis
Note: You may need or want to purchase one or more of the following items for your server:
•
•
•
•
•
iv
One or two Intel® Xeon 5500 series and Intel® Xeon 5600 series processors
DDR3 RDIMM/UDIMM Memory
Hard drive
Slimline CD-ROM or DVD-ROM drive
RAID controller add-in card
Intel® Server System SR1690WB Service Guide
• Operating system
• For information about which accessories, memory, processors, and third-party
hardware were tested and can be used with your board, and for ordering information
for Intel products, see: http://support.intel.com/support/motherboards/server/
S5500WB/compat.htm
Intel® Server System SR1690WB Service Guide
v
vi
Intel® Server System SR1690WB Service Guide
Safety Information
Important Safety Instructions
Read all caution and safety statements in this document before performing any of the
instructions. See also Intel Server Boards and Server Chassis Safety Information on the
Intel® Server Deployment Toolkit CD and/or at http://support.intel.com/support/
motherboards/server/sb/cs-010770.htm.
Wichtige Sicherheitshinweise
Lesen Sie zunächst sämtliche Warnund Sicherheitshinweise in diesem Dokument, bevor
Sie eine der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu
Intel-Serverplatinen und Servergehäusen auf der Intel® Server Deployment Toolkit CD
oder unter http://support.intel.com/support/motherboards/server/sb/cs-010770.htm.
Consignes de sécurité
Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce
document avant de suivre toute instruction. Consultez Intel Server Boards and Server
Chassis Safety Information sur le Intel® Server Deployment Toolkit CD ou bien rendezvous sur le site http://support.intel.com/support/motherboards/server/sb/cs-010770.htm.
Instrucciones de seguridad importantes
Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar
cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety
Information en el Intel® Server Deployment Toolkit CD y/o en http://support.intel.com/
support/motherboards/server/sb/cs-010770.htm.
重要安全指导
在执行任何指令之前,请阅读本文件中的所有注意事项及安全声明。并参阅 http://
support.intel.com/support/motherboards/server/sb/CS-010770.htm 上的 Intel Server
Boards and Server Chassis Safety Information (《Intel 服务器主板与服务器
机箱安全信息》)。
vii
Warnings
Heed safety instructions: Before working with your server product, whether you are
using this guide or any other resource as a reference, pay close attention to the safety
instructions. You must adhere to the assembly instructions in this guide to ensure and
maintain compliance with existing product certifications and approvals. Use only the
described, regulated components specified in this guide. Use of other products /
components will void the UL listing and other regulatory approvals of the product and
will most likely result in noncompliance with product regulations in the region(s) in which
the product is sold.
System power on/off: The power button DOES NOT turn off the system AC power. To
remove power from system, you must unplug the AC power cord from the wall outlet.
Make sure the AC power cord is unplugged before you open the chassis, add, or remove
any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be
present on power, telephone, and communication cables. Turn off the server and
disconnect the power cord, telecommunications systems, networks, and modems attached
to the server before opening it. Otherwise, personal injury or equipment damage can
result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives,
boards, and other parts. We recommend that you perform all procedures in this chapter
only at an ESD workstation. If one is not available, provide some ESD protection by
wearing an antistatic wrist strap attached to chassis ground—any unpainted metal
surface—on your server when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely
sensitive to ESD. Hold boards only by their edges. After removing a board from its
protective wrapper or from the server, place the board component side up on a grounded,
static free surface. Use a conductive foam pad if available but not the board wrapper. Do
not slide board over any surface.
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips
over two jumper pins. Some jumpers have a small tab on top that you can grip with your
fingertips or with a pair of fine needle nosed pliers. If your jumpers do not have such a tab,
take care when using needle nosed pliers to remove or install a jumper; grip the narrow
sides of the jumper with the pliers, never the wide sides. Gripping the wide sides can
damage the contacts inside the jumper, causing intermittent problems with the function
controlled by that jumper. Take care to grip with, but not squeeze, the pliers or other tool
you use to remove a jumper, or you may bend or break the pins on the board.
viii
Intel® Server System SR1690WB Service Guide
Contents
Preface ........................................................................................................................ iii
About this Manual ................................................................................................................. iii
Manual Organization ............................................................................................................. iii
Product Contents .................................................................................................................. iv
Intel® Server System SR1690WB - Product Contents ................................................. iv
Safety Information .................................................................................................... vii
Important Safety Instructions ............................................................................................... vii
Wichtige Sicherheitshinweise .............................................................................................. vii
Consignes de sécurité ......................................................................................................... vii
Instrucciones de seguridad importantes .............................................................................. vii
Warnings ..............................................................................................................................viii
Chapter 1: Server System References ..................................................................... 1
Chapter 2: Server System Features .......................................................................... 3
Cable Routing ........................................................................................................................ 6
Chassis Component Identification ......................................................................................... 8
Internal Components ..................................................................................................... 8
Server Board Connector and Component Locations ............................................................ 9
Configuration Jumpers ......................................................................................................... 11
Intel® Light Guided Diagnostics ...........................................................................................13
Back Panel Connectors .......................................................................................................15
RAID Support .......................................................................................................................16
Front Panel of Server System ..............................................................................................17
Standard Control Panel ...............................................................................................17
Rear of Server System ........................................................................................................19
Peripheral Devices ......................................................................................................19
Hard Disk Drives ..........................................................................................................20
Slimline Optical Drive latch ..........................................................................................20
Rack-Mounted Systems .......................................................................................................20
Hardware Requirements ......................................................................................................21
Processor ....................................................................................................................21
Memory ........................................................................................................................21
Memory Sparing and Mirroring ............................................................................................22
Power Supply .......................................................................................................................23
Optional Hardware ...............................................................................................................23
Intel® RAID Activation Key ..........................................................................................23
Intel® Remote Management Module 3 ........................................................................23
Intel® I/O Expansion Module .......................................................................................24
Intel® Server System SR1690WB Service Guide
ix
Chapter 3: Hardware Installations and Upgrades ..................................................25
Before You Begin ................................................................................................................ 25
Tools and Supplies Needed ........................................................................................ 25
System References ..................................................................................................... 25
Removing and Installing the System Cover ........................................................................ 25
Removing the System Cover ...................................................................................... 25
Installing the System Cover ........................................................................................ 26
Removing and Installing the Processor Air Duct ................................................................. 27
Removing the Processor Air Duct ............................................................................... 27
Installing the Processor Air Duct ................................................................................. 28
Installing and Removing Memory ........................................................................................ 29
Installing DIMMs .......................................................................................................... 29
Removing DIMMs ........................................................................................................ 30
Installing or Replacing the Processor .......................................................................... 31
Installing the Processor ............................................................................................... 31
Installing the Heat Sink(s) ........................................................................................... 34
Replacing a Processor ................................................................................................ 34
Installing and Removing a Hot-swap Hard Drive ................................................................. 35
Installing a SAS or SATA Hot-swap Hard Disk Drive .................................................. 35
Removing a SAS or SATA Hot-swap Hard Disk Drive ................................................ 38
Installing or Removing a Slimline Optical Drive ................................................................... 38
Installing a Slimline Optical Drive ........................................................................................ 38
Removing a Slimline Optical Drive .............................................................................. 41
Installing and Removing the PCI Riser Assembly ............................................................... 41
Removing the PCI Riser Assembly ............................................................................. 41
Installing the PCI Riser Assembly ............................................................................... 41
Installing and Removing a PCI Add-In Card ........................................................................ 42
Installing a PCI Add-In Card ........................................................................................ 42
Removing a PCI Add-In Card ...................................................................................... 43
Removing and Installing the System Fans .......................................................................... 44
Replacing the System Fans ........................................................................................ 44
Installing and Removing the I/O Expansion Module(s) ....................................................... 47
Installing the I/O Expansion Module(s) ....................................................................... 47
Removing the I/O Expansion Module(s) ..................................................................... 49
Installing and Removing the Intel® Remote Management Module 3 and the Intel® RMM 3 NIC
50
Installing the Intel® RMM3 and Intel® RMM3 NIC ...................................................... 50
Removing the Intel® RMM3 and Intel® RMM3 NIC ..................................................... 51
Replacing the Backplane Board .......................................................................................... 51
Removing the Backplane Board .................................................................................. 52
Installing the Backplane Board .................................................................................... 52
Replacing the Server Board ................................................................................................ 53
Removing the Server Board ........................................................................................ 53
Installing the Server Board .......................................................................................... 54
x
Intel® Server System SR1690WB Service Guide
Replacing the Backup Battery .............................................................................................56
Replacing the Power Supply ................................................................................................57
Removing the Power Supply .......................................................................................57
Installing the Power Supply .........................................................................................58
Installing and Removing the Rack Handles .........................................................................59
Installing the Rack Handles .........................................................................................59
Removing the Rack Handles ...............................................................................................60
Chapter 4: Server Utilities ........................................................................................ 61
Using the BIOS Setup Utility ................................................................................................61
Starting Setup ..............................................................................................................61
If You Cannot Access Setup ........................................................................................61
Setup Menus ...............................................................................................................61
Upgrading the BIOS .............................................................................................................63
Preparing for the Upgrade ...........................................................................................63
Upgrading the BIOS ....................................................................................................64
Clearing the CMOS ..............................................................................................................64
Resetting the Password .......................................................................................................65
Appendix A: Technical Reference .......................................................................... 67
650-W Single Power Supply Input Voltages ........................................................................67
650-W Single Power Supply Output Voltages .....................................................................67
System Environmental Specifications ..................................................................................68
Appendix B: Intel® Server Issue Report Form ....................................................... 69
Appendix C: LED Decoder ....................................................................................... 73
Appendix D: Getting Help ........................................................................................ 83
Warranty Information ...........................................................................................................83
Appendix E: Regulatory and Compliance Information ......................................... 85
Product Regulatory Compliance ..........................................................................................85
Product Safety Compliance .................................................................................................85
Product EMC Compliance - Class A Compliance ........................................................86
Certifications / Registrations / Declarations .................................................................86
Product Regulatory Compliance References ..............................................................87
Electromagnetic Compatibility Notices ................................................................................90
FCC Verification Statement (USA) ..............................................................................90
Industry Canada (ICES-003) .......................................................................................91
Europe (CE Declaration of Conformity) .......................................................................91
VCCI (Japan) ...............................................................................................................91
BSMI (Taiwan) .............................................................................................................92
KCC (Korea) ................................................................................................................92
Rack Mount Installation Guidelines .............................................................................93
Power Cord Usage Guidelines ....................................................................................94
Product Ecology Compliance ......................................................................................95
Intel® Server System SR1690WB Service Guide
xi
Other Markings ............................................................................................................ 98
Regulated Specified Components ............................................................................... 99
End-of-Life / Product Recycling ................................................................................. 100
Appendix F: Warranty .............................................................................................101
Limited Warranty for Intel® Chassis Subassembly Products ............................................. 101
Extent of Limited Warranty ........................................................................................ 101
Limitations of Liability ................................................................................................ 102
How to Obtain Warranty Service ............................................................................... 102
Appendix G: Installation/Assembly Safety Instructions .....................................105
Important Safety Instructions ............................................................................................. 105
English ............................................................................................................................... 105
Wichtige Sicherheitshinweise ............................................................................................ 106
Consignes de sécurité ............................................................................................... 107
Italiano ............................................................................................................................... 109
Appendix H: Safety Information ............................................................................111
English ............................................................................................................................... 111
Server Safety Information ......................................................................................... 111
Safety Warnings and Cautions .................................................................................. 111
Intended Application Uses ........................................................................................ 112
Site Selection ............................................................................................................ 112
Equipment Handling Practices .................................................................................. 112
Deutsch ............................................................................................................................. 113
Sicherheitshinweise für den Server ........................................................................... 113
Sicherheitshinweise und Vorsichtsmaßnahmen ....................................................... 113
Zielbenutzer der Anwendung .................................................................................... 114
Standortauswahl ....................................................................................................... 114
Handhabung von Geräten ......................................................................................... 114
Warnungen zu Netzspannung und Elektrizität .......................................................... 115
Warnhinweise für den Systemzugang ....................................................................... 116
Warnhinweise für Racks ........................................................................................... 116
Elektrostatische Entladungen (ESD) ......................................................................... 117
Andere Gefahren ....................................................................................................... 117
Français ............................................................................................................................. 118
Consignes de securite sur le serveur ........................................................................ 118
Séurité: avertissements et mises en garde ............................................................... 118
Domaines d’utilisation prévus ................................................................................... 119
Sélection d’un emplacement ..................................................................................... 119
Pratiques de manipulation de l’équipement .............................................................. 120
Alimentation et avertissements en matiére d’électricité ............................................ 120
Avertissements sur le cordon d’alimentation ............................................................. 121
Avertissements sur l’accés au systéme .................................................................... 121
Avertissements sur le montage en rack .................................................................... 122
xii
Intel® Server System SR1690WB Service Guide
Décharges électrostatiques (ESD) ............................................................................123
Autres risques ............................................................................................................123
Périphériques laser ....................................................................................................124
Español ..............................................................................................................................124
Información de seguridad del servidor ......................................................................124
Advertencias y precauciones sobre seguridad ..........................................................124
Aplicaciones y usos previstos ....................................................................................125
Seleccién de la ubicación ..........................................................................................125
Manipulacién del equipo ............................................................................................126
Advertencias de alimentacién y eléctricas .................................................................126
Advertencias sobre el cable de alimentación ............................................................126
Advertencias el acceso al sistema ............................................................................127
Advertencias sobre el montaje en bastidor ...............................................................128
Descarga electrostática (ESD) ..................................................................................129
Otros riesgos .............................................................................................................129
Intel® Server System SR1690WB Service Guide
xiii
xiv
Intel® Server System SR1690WB Service Guide
List of Figures
Figure 1. Intel® Server System SR1690WB .............................................................................. 3
Figure 2. Cable Routing ............................................................................................................ 8
Figure 3. System Components.................................................................................................. 8
Figure 4. Server Board Connector and Component Locations ............................................... 10
Figure 5. Configuration Jumper Location ................................................................................ 12
Figure 6. Light Guided Diagnostic LEDs ................................................................................. 14
Figure 7. Back Panel Connectors............................................................................................ 15
Figure 8. Front Control Panel - Intel® Server System SR1690WB.......................................... 17
Figure 9. Server System I/O Connector Locations.................................................................. 19
Figure 10. Optional Peripherals............................................................................................... 20
Figure 11. DIMM Configuration Diagram................................................................................. 21
Figure 12. Channel Slots Configuration .................................................................................. 22
Figure 13. Removing the Server System Cover...................................................................... 26
Figure 14. Installing the Server System Cover........................................................................ 27
Figure 15. Removing the Processor Air Duct .......................................................................... 28
Figure 16. Installing the Processor Air Duct ............................................................................ 29
Figure 17. Installing the Memory ............................................................................................. 30
Figure 18. Lifting the Load Lever............................................................................................. 31
Figure 19. Open the Load Plate .............................................................................................. 32
Figure 20. Removing the socket.............................................................................................. 32
Figure 21. Aligning the Processor ........................................................................................... 33
Figure 22. Close the Load Plate and Socket Lever................................................................. 33
Figure 23. IU Reference Heat sink Assembly ......................................................................... 34
Figure 24. Pulling out the back lever ....................................................................................... 36
Figure 25. 2.5 HDD Installation ............................................................................................... 36
Figure 26. 3.5 HDD Installation ............................................................................................... 37
Figure 27. Locking the drive assembly.................................................................................... 37
Figure 28. Removing the Knockout in Bezel for Optical Opening ........................................... 39
Figure 29. Attaching the Brackets to the Optical Drive............................................................ 39
Figure 30. Installing the Optical Drive into the Server System ................................................ 40
Figure 31. Removing the PCI Riser Assembly from the Server System ................................. 41
Figure 32. Installing the PCI Riser Assembly .......................................................................... 42
Figure 33. Installing a PCI Card in a Riser Card ..................................................................... 43
Figure 34. Removing a PCI Card in a Riser Card ................................................................... 43
Figure 35. Replacing the system fans ..................................................................................... 45
Figure 36. Remove the screws from the fans.......................................................................... 46
Figure 37. Inserting the fan into the fan module...................................................................... 47
Figure 38. Installing the I/O Expansion Module(s) .................................................................. 48
Figure 39. Attaching the I/O Expansion Module(s).................................................................. 49
Figure 40. Installing the Intel® RMM3 and Intel® RMM3 NIC.................................................. 50
Figure 41. Attach the Intel® RMM3 module to rear chassis .................................................... 51
Figure 42. Removing the backplane board ............................................................................. 52
Intel® Server System SR1690WB Service Guide
xv
Figure 43. Installing the backplane board ...............................................................................
Figure 44. Removing the Server Board ..................................................................................
Figure 45. Installing the Server Board ....................................................................................
Figure 46. Replacing the Backup Battery ...............................................................................
Figure 47. Removing the Power Supply from the Server System...........................................
Figure 48. Installing the Power Supply into the Server System ..............................................
Figure 49. Installing the Rack Handle .....................................................................................
Figure 50. Removing the Rack Handle ...................................................................................
Figure 51. CMOS Recovery Jumper.......................................................................................
Figure 52. Password Recovery Jumper..................................................................................
Figure 53. Diagnostic LED Placement Diagram .....................................................................
xvi
53
54
55
57
58
59
60
60
65
66
73
Intel® Server System SR1690WB Service Guide
List of Tables
Table 1. Server System References ......................................................................................... 1
Table 2. Intel® Server System SR1690WB Feature Summary ................................................. 3
Table 3. NIC LED Descriptions ...............................................................................................15
Table 4. Control Panel LED Functions ....................................................................................17
Table 5. List of Supported I/O Modules on SR1690WB ..........................................................24
Table 6. Setup Menu Key Use ................................................................................................62
Table 7. 650-W Single Power Supply Output Voltages ...........................................................67
Table 8. System Environmental Specifications .......................................................................68
Table 9. POST Progress Code LED Example .........................................................................73
Table 10. Diagnostic LED POST Code Decoder .....................................................................74
Table 11. Product Regulatory Compliance References ..........................................................87
Table 12. Product Ecology Compliance ..................................................................................95
Table 13. Other Markings ........................................................................................................98
Intel® Server System SR1690WB Service Guide
xvii
xviii
Intel® Server System SR1690WB Service Guide
1
Server System References
If you need more information about this product or information about the accessories that
can be used with this server system, use the following resources.
Table 1. Server System References
For this information or
software
For in-depth technical
information about the
server system, including
sub-system overviews
and mechanical drawings
Use this Document or Software
Intel® Server System SR1690WB Technical Product Specification
can be found at:
http://support.intel.com/support/motherboards/server/S5500WB/
Intel® Server System SR1690WB Technical Product Specification
can be found at:
http://support.intel.com/support/motherboards/server/S5500WB/
For basic BIOS settings
and chipset information
Intel® Server System SR1690WB Technical Product Specification
Found at:
http://support.intel.com/support/motherboards/server/S5500WB/
If you just received this
product and need to
install it
Intel® Server System SR1690WB Quick Start User's Guide in the
product box
Accessories or other Intel
server products
Spares and Configuration Guide can be found at:
Hardware (peripheral
boards, adapter cards)
and operating systems
that were tested with this
product
Tested Hardware and Operating System List can be found at:
Processors there were
tested with this product
Supported Processors can be found at:
DIMMs that were tested
with this product
Supported Memory can be found at:
To make sure your system
falls within the allowed
power budget
Power Budget Tool can be found at:
For software to manage
your Intel® server
Intel® Server Management Software can be found at:
http://support.intel.com/support/motherboards/server/S5500WB/
http://support.intel.com/support/motherboards/server/S5500WB/
http://support.intel.com/support/motherboards/server/S5500WB/
http://support.intel.com/support/motherboards/server/S5500WB/
http://support.intel.com/support/motherboards/server/S5500WB/
http://support.intel.com/support/motherboards/server/sysmgmt/
index.htm
and on the Intel® Server Management Software CD that ships with
your system.
1
Table 1. Server System References
For this information or
software
For drivers
Use this Document or Software
Driver (for an extensive list of drivers available)
Operating System Driver (for operating system drivers)
http://support.intel.com/support/motherboards/server/S5500WB/
For firmware and BIOS
updates
Firmware Update can be found at:
For diagnostics test
software
Diagnostics: Platform Confidence Test (PCT)
http://support.intel.com/support/motherboards/server/S5500WB/
Found at:
http://support.intel.com/support/motherboards/server/S5500WB/
and available on the Intel®Server Deployment Toolkit 3.0 CD that
ships with your system.
2
Intel® Server System SR1690WB Service Guide
2
Server System Features
This chapter briefly describes the main features of the Intel® Server System SR1690WB.
This chapter provides illustrations of the product, a list of the server system features, and
diagrams showing the location of important components and connections on the server
system.
al
tic e
Op evic
D
AF003210
Figure 1. Intel® Server System SR1690WB
Table 2 summarizes the features of the server system.
Table 2. Intel® Server System SR1690WB Feature Summary
Feature
Dimensions
Description
•
•
•
•
1.69 inches (43mm) high
17.76 inches (451.17mm) wide
26.42 inches (671.08mm) deep
24.58 lbs (11.15kg) weight
Raw Storage Capacity
System raw storage capacity is based on the HDD capacity and
number of HDDs used in the system. Raw storage capacity is the sum
of single HDD capacity used in system.
External Drive Bays
Four hot-pluggable external drive bays
Hard Disk Drive
Supported
•
•
3.5-inch SATA, SAS HDD.
2.5-inch SATA, SAS HDD.
3
Table 2. Intel® Server System SR1690WB Feature Summary
Feature
Processor
Description
•
•
Memory Capacity
Support for one or two Intel® Xeon® Processor 5500 series and
Intel® Xeon® Processor 5600 series processors in FC-LGA 1366
Socket B package with up to 95 W Thermal Design Power (TDP).
Supports future processor compatibility guidelines
4.8 GT/s, 5.86 GT/s, and 6.4 GT/s Intel® Quick Path Interconnect
(Intel® QPI).
Meets EVRD11.1
Expandable to 64 GB maximum.
•
Memory Type
240-pin keyed support for 800/166/1333 MT/s ECC Registered
(RDIMM) or Unbuffered (UDIMM) DDR3 memory.
• 8 DIMMs total across six memory channels (three channels per
processor in a 2:1:1 configuration).
No support for Quad-Rank x4 DIMMs
DIMM Slots
Eight
Chipset
Intel® Chipset which includes the following components:
Intel® 5500 chipset IOH (IOH24D)
Intel® 82801Jx I/O Controller Hub (ICH10R)
System Connectors/
Headers
•
•
System Fan Support
Add-in Adapter
Support
•
•
External I/O connectors:
– DB-15 Video connectors
– RJ-45 serial Port A connector
– RJ-45 connector for 10/100/1000 LAN
– One 2x USB 2.0 connectors
– One RJ-45 over USB for 10/100/1000 LAN
Internal connectors/headers:
– Two USB 2x5 pin header, supporting up to four USB 2.0 ports
– One low-profile USB 2x5 pin
– One DH-10 Serial Port B header
– One 2x8 pin VGA header with presence detection to switch
from rear I/O video connector
– Six SATA II connectors
– Dual Connectors for Intel®I/O Expansion Module
– One RMM3 connector to support optional Intel® Remote
Management Module 3
– SATA SW RAID 5 Activation Key Connector
– One SSI-EEB compliant front panel header
Two sets of CPU fans
Two sets of DIMM fans
Intel® Server Board S5500WB SSI-compliant
One riser slot supporting full-height or low-profile 1U and 1U MD2 PCI
Express* x16 riser cards.
Two connectors supporting double- and single-wide Intel®I/O
Expansion Modules.
4
Intel® Server System SR1690WB Service Guide
Table 2. Intel® Server System SR1690WB Feature Summary
Feature
On-board Video
Description
On-board Server Engines* LLC Pilot II Controller
Matrox* G200 2D Video Graphics controller
Uses 8 MB of the BMC 32 MB DDR2 Memory
LAN Support
Two 10/100/1000 ports provided by Intel® 82576 with Intel® I/O
Acceleration Technology (I/OAT)
System Power
Single 650-W power supply, 80 plus silver with PFC
System Management
On-board Server Engines* LLC Pilot II Controller.
Integrated Baseboard Management Controller (Integrated BMC), IPMI
2.0 compliant
•
•
Basic
– BMC Controller: ARC 926E-S microcontroller
– Super IO: Serial Port logic, legacy interfaces, LPC interface,
Port80
– Hardware Monitoring: Fan speed control and voltage
monitoring
Advanced
– Video and USB compression and redirection
– NC-SI port, a high-speed sideband management interface
– Integrated Super I/O on LPC interface
Intel® Server System SR1690WB Service Guide
5
Cable Routing
When you add or remove components from your server system, make sure your cables are
routed correctly before reinstalling the server system cover. Use caution to make sure no
cables or wires are pinched and that the airflow from the fans is not blocked. Use the
following figures to determine the correct cable routing for the SR1690WB system.
6
Intel® Server System SR1690WB Service Guide
RAID Module
Battery Backup Unit
Power Supply
Backplane
Optical Drive
Fan Modules
Power from BBU
to RAID Module
H
H SES cable from RAID
Module to Backplane
I Main Power
J Aux. Signal Power
K CPU Power
L Power to Fans
M Power to Optical Drive
N Power to Backplane(2)
A
RAID Card
A
B
C
D
E
F
G
O IPMB Cable from Backplane
P SGPIO Cable from Backplane
Q SATA Data Cables
G
5
0
4
1
3
2
I
C
Server Board
J
L
B
L
K
F
1
2
3
4
Q
P
N
HDD 0
M
N
D
HDD 1
HDD 2
HDD 3
O
E
AF003307
Intel® Server System SR1690WB Service Guide
7
Figure 2. Cable Routing
Chassis Component Identification
This section helps you identify the components of your server system. If you are near the
system, you can also use the Quick Reference Label provided on the inside of the chassis
cover to assist in identifying components.
Internal Components
F
G
H
E
D
C
B
A
I
al
tic e
Op evic
D
K
J
A
AF003211
A.
Rack handles (two)
G.
PCI Express* x16 riser
B.
Front Control Panel
H.
Mother board
C.
Hot swap backplane
I.
650W power supply unit
D.
System Fans (CPU fans and Memory fans) J.
Optional slimline optical drive
E.
Air Duct
Hot swap HDD carrier
F.
PCI Express* add-in card bracket
K.
Figure 3. System Components
8
Intel® Server System SR1690WB Service Guide
Server Board Connector and Component Locations
A
B
C D
E
F
G
H
PP
OO
NN
MM
I
LL
KK
JJ
II
HH
GG
J
K
L
EE CC AA Y X
FF DD BB Z
U
W
V
S Q O M
T R P N
AF003212
Description
Description
A.
Dual Intel® I/O Expansion Module
Connectors
W.
8-pin CPU Connector
B.
PCI Express* x16 Gen2
X.
Processor Socket 2
C.
Remote Management Module 3
Y.
4-pin Fan Connector (CPU2)
D.
POST Code LEDs
Z.
4-pin Fan Connector (CPU2A)
E.
External I/O
AA.
4-pin Fan Connector (MEM2)
F.
USB Connector
BB.
8-pin Fan Connector (MEM2R)
Intel® Server System SR1690WB Service Guide
9
Description
Description
G.
Battery
CC.
DIMM Slot D2
H.
SATA Connectors 0~5
DD.
DIMM Slot D1
I.
24-pin Power Connector
EE.
DIMM Slot E1
J.
N/A
FF.
DIMM Slot F1
K.
Aux Power (5-pin or 7-pin)
GG.
Front Panel Connector
L.
RAID Key
HH.
HDD LED Header
M.
DIMM Slot C1
II.
Low-Profile USB Connector
N.
DIMM Slot B1
JJ.
Internal VGA Connector
O.
DIMM Slot A1
KK.
N/A
P.
DIMM Slot A2
LL.
USB Connector
Q.
8-pin Fan Connector (MEM1R)
MM.
Slot 1 PCI Express* x8 Gen2
R.
4-pin Fan Connector (MEM1)
NN.
SGPIO Connector
S.
4-pin Fan Connector (CPU1A)
OO.
IMPB Connector
T.
4-pin Fan Connector (CPU1)
PP.
Serial Port B
U.
N/A
V.
Processor Socket 1
Figure 4. Server Board Connector and Component Locations
10
Intel® Server System SR1690WB Service Guide
Configuration Jumpers
J6A3
E
J6A2
F
DCD to DTR
Internal
External
DSR to DTR
ME BMC Update
J7A2
A
BMC Force Update
J1B5
A
D
Normal
Update
Password Clear
J1C2
B
Normal
B
C
Clear
Password
BIOS Recovery Mode
J1C3
C
Normal
Recovery
J1B4
D
Normal
Reset BIOS
AF003049
Intel® Server System SR1690WB Service Guide
11
Jumper Name
J8C1: BMC
Force Update
Pins
What happens at system reset...
1-2
BMC Firmware Force Update Mode Disabled (Default)
2-3
BMC Firmware Force Update Mode Enabled
1-2
Normal System Operation (Default)
2-3
Administrator and user passwords are
cleared on the next reset
1-2
Normal System Operation (Default)
2-3
The main system BIOS will not boot with
these pins jumpered. Note: the system boots
from EFI-bootable recovery media with a
recovery BIOS image.
Reset BIOS
Configuration(J1
B4)
1-2
Normal System Operation (Default)
2-3
Clear CMOS settings
Video
Master(J6A3)e
1-2
Internal connector overrides
2-3
External connector overrides
1-2
DTR (Data Terminal Ready) mode
2-3
DCD (Data Carrier Detect) mode
None
DSR (Data Set Ready) mode
Password
Clear(J1C2)
BIOS
Recovery(J1C3)
Serial
Interface(J6A2)
Figure 5. Configuration Jumper Location
12
Intel® Server System SR1690WB Service Guide
Intel® Light Guided Diagnostics
The server system contains numerous LEDs providing the following functions:
• The System Status LED on the front and back panels (see Figure 6) shows the
overall health of the system (green, blinking green, blinking amber, and off).
• The System Identification LED on the back panel (see Figure 6) helps identify the
server from among several servers. By default, the ID LED is off, and blue when
activated by button or software.
• DIMM Fault LEDs on the server board (see Figure 6) help identify failed and failing
DIMM slots. The DIMM fault LEDs turn on (amber) if there is a DIMM fault.
• POST Code Diagnostic LEDs on the server board (see Figure 6) change color or
state (off, green, red, amber) according to the POST sequence.
• The 5-V STBY LED on the server board (see Figure 6) is illuminated (green) when
AC power is applied.
• The Fan Fault LEDs on the server board (see Figure 6) help identify failed and
failing fans. The fan fault LEDs turn on (amber) if there is a fan fault.
Intel® Server System SR1690WB Service Guide
13
A
B C
D
G
E
FLT_F
FLT_D1
FLT_E
FLT_D2
FLT_A2
FLT_B
FLT_A1
FLT_C
F
AF003216
A.
Diagnostic LED
B.
System Status LED
C.
System ID LED
D.
5V Standby LED
E.
CPU1 DIMM fault LEDs
F.
Fan Fault LEDs
G.
CPU2 DIMM fault
LEDs
Figure 6. Light Guided Diagnostic LEDs
14
Intel® Server System SR1690WB Service Guide
Back Panel Connectors
A
B
C
D
E
AF003217
A.
NIC1 connector with USB
ports 2, 5
B.
USB ports 8, 9
C.
NIC2 connector
D.
RJ-45 Serial B port
E.
Internal Video Connector
Figure 7. Back Panel Connectors
The NIC LEDs at the right and left of each NIC provide the following information.
Table 3. NIC LED Descriptions
LED
NIC1/
NIC2
LED
State
Left
LED
Right
LED
LED State
Description
Off
No network connection
Solid Amber
Network connection in place
Blinking Amber
Transmit/receive activity
Off
10 Mbps connection (if left
LED is on or blinking)
Solid Amber
100 Mbps connection
Solid Green
1000 Mbps connection
Intel® Server System SR1690WB Service Guide
15
RAID Support
The Intel® Server Board S5500WB provides an integrated SATA II host controller that
supports independent DMA operation on the six Ports and supports data transfer rates of
up to 3.0 Gb/Sec.
The ICH10R provides support for Intel® Matrix Storage Technology, providing both
AHCI and integrated RAID functionality. The industry-leading RAID capability provides
high-performance RAID 0, 1, 5 and 10 functionality on up to six SATA ports.
The BIOS Setup utility provides multiple drive configuration options on the Advanced |
Mass Storage Controller Configuration setup page, some of which affect the ability to
configure RAID. The “Onboard SATA Controller” option is enabled by default. When this
option is enabled, the “SATA Mode” option can be set to ENHANCED mode,
COMPATIBILITY mode, AHCI mode or SW RAID mode. The modes affect the
configuration as follows:
• ENHANCED mode supports up to six SATA ports with IDE Native Mode.
• COMPATIBILITY mode supports up to four SATA ports[0/1/2/3] with IDE Legacy
mode and 2 SATA ports[4/5] with IDE Native Mode.
• AHCI mode supports all SATA ports using the Advanced Host Controller Interface
when the option is enabled.
Note: For AHCI capability in EFI, the AHCI legacy Option ROM should be set to “disabled”.
• SW RAID mode supports configuration of SATA ports for RAID via RAID
configuration software.
For RAID 0, 1, and 10, enclosure management is provided through the SATA_SGPIO
connector on the server board when a cable is attached between this connector on the
server board and to the backplane or I2C interface.
If RAID 5 is desired, the optional Intel® RAID Activation Key AXXRAKSW5 can be
installed. To enable RAID 5, this activation key is placed on the SATA Key connector that
is located at the right side of the server board. For information on how to install the Intel®
RAID Activation Key AXXRAKSW5 accessory to enable RAID 5, see the
documentation that is included with the accessory kit.
16
Intel® Server System SR1690WB Service Guide
Front Panel of Server System
Standard Control Panel
The following diagram shows the features of the standard control panel.
A
B
C
D
E
F
G
H
I
AF003218
Item
Feature
A.
Power/Sleep Button
B.
System Reset Button
C.
Power/Sleep LED
D.
System NIC 1 Activity LED
E.
System NIC 2 Activity LED
F.
System Identification LED
G.
System Status LED
H.
System Identification Button
I.
USB 2.0 connectors – Port 0 & 1
Figure 8. Front Control Panel - Intel® Server System SR1690WB
.
Table 4. Control Panel LED Functions
LED
Power/
Sleep
LAN 1 and
LAN 2
Color
State
Description
Green
On
Power On/ACPI S0 state
Green
Blink
Sleep /ACPI S1 state
-
Off
Power Off /ACPI S5 state
Green
On
LAN Link no Access
Green
Blink
LAN Activity
-
Off
No Link
Intel® Server System SR1690WB Service Guide
17
Table 4. Control Panel LED Functions
LED
System ID
System
Status
Color
Blue
State
Description
On
Identify Active via command or button
Off
No Identification
Green
On
System Ready / No Alarm
Green
Blink
System ready, but degraded: redundancy lost such as
the power supply or fan failure; non-critical temp/
voltage threshold; battery failure; or predictive power
supply failure.
Amber
On
Critical Alarm: Critical power modules failure, critical
fans failure, voltage (power supply), critical
temperature and voltage
Amber
Blink
Non-Critical Alarm: Redundant fan failure, redundant
power module failure, non-critical temperature and
voltage
-
Off
AC power off: System unplugged AC power on:
System powered off and in standby, no prior
degraded\non-critical\critical state
Note: Blink rate is ~1 Hz at 50% duty cycle.
It is also off when the system is powered off (S5) or in a sleep state (S1).
The power LED sleep indication is maintained on standby by the chipset. If the system is
powered down without going through the BIOS, the LED state in effect at the time of
power off is restored when the system is powered on until the BIOS clear it.
If the system is not powered down normally, it is possible the Power LED will blink at the
same time the system status LED is off due to a failure or configuration change that
prevents the BIOS from running.
18
Intel® Server System SR1690WB Service Guide
Rear of Server System
A
B
N
C
D
L
M
K
J
I
H
G
F
E
AF003220
A.
AC Power Receptacle
I.
RJ-45 Serial B port
B.
NIC 1 connector
J.
NIC2 Connector
C.
Top Cover Release Screw
K.
USB port 9
D.
PCI Express* Add-in Card
L.
USB port 8
E.
IO module external connector 2 (optional)
M.
USB port 5
F.
IO module external connector 1 (optional)
N.
USB port 2
G.
Management Network Interface (optional)
H.
Internal Video Connector
Figure 9. Server System I/O Connector Locations
Peripheral Devices
The server system provides locations and hardware for installing hard drives and a
slimline optical drive. You must purchase the drives separately. The following figure
shows the available options.
A
E D
B
C
AF003221
Intel® Server System SR1690WB Service Guide
19
A.
Front Control Panel
B.
Slimline Optical Drive
C.
Hard Drive Bays HDD0~3
D.
HDD Status LED
E.
HDD Power LED
Figure 10. Optional Peripherals
Hard Disk Drives
The server system ships with four hot-swap drive carriers for installing four SATA/SAS
Hard disk drives, both 3.5-inch or 2.5-inch HDDs.
For instructions on installing hard drives, see “Installing and Removing a Hot-swap Hard
Drive” on page -35.
Slimline Optical Drive latch
You can use a slimline optical drive latch with an optional optical drive. One slimline
optical drive latch is included with your server system; you must purchase the optical
drive separately.
You can only insert or remove the slimline optical drive when the system power is turned
off. Drive in the optical drive bay is NOT hot-swappable. For installation instructions on
installing an optical drive, see “Installing or Removing a Slimline Optical Drive” on
page -38.
To use one of the drives provided by Intel, use the following order codes:
• SATA Slimline DVD Drive: AXXSATADVDROM
• SATA Slimline DVD Rewriteable Drive: AXXSATADVDRWROM
Rack-Mounted Systems
Your Intel® Server System SR1690WB can be mounted into a rack. Intel provides three
options to mount this server into a rack. When installing the chassis into a rack, Intel
recommends you install systems from the bottom of the rack to the top. In other words,
install the first system in the rack into the bottom position of the rack, the second system
in the second position from the bottom, and so on. Instructions for installing your chassis
into a rack are included in the rail kit.
20
Intel® Server System SR1690WB Service Guide
Hardware Requirements
To avoid integration difficulties and possible board damage, your system must meet the
requirements outlined below. For a list of qualified components, see the links under
“Server System References”.
Processor
The Intel® Server System SR1690WB supports one or two Intel® Xeon® Processor 5500
series and Intel® Xeon® Processor 5600 series with 95W Thermal Design Power (TDP) or
less and with a max data transfer rate of 6.4 GT/s. For a complete list of supported
processors, see the links under “Server System References”.
Memory
The Intel® Server System SR1690WB supports a DDR3-based memory subsystem. The
Intel® Server System SR1690WB supports two DIMMs per channel. The silkscreen on
the board for the DIMMs displays DIMM_A1, DIMM_A2, DIMM_B1, DIMM_B2,
DIMM_D1, DIMM_D2, DIMM_E1, DIMM_E2. See Figure 11. The minimal memory
population possible is DIMM_A1.
DIMM D2
DIMM D1
DIMM E1
DIMM F1
DIMM A2
DIMM A1
DIMM B1
DIMM C1
Channel F
Channel E
Channel D
Channel C
Channel B
Channel A
AF003226
Figure 11. DIMM Configuration Diagram
For two slots per channel configurations, the server board requires DDR3 DIMMs within
a channel to be populated starting with the DIMM farthest from the processor. See the
following figure (Figure 12).
For a complete list of supported memory DIMMs, see the links under “Server System
References”.
Intel® Server System SR1690WB Service Guide
21
Figure 12. Channel Slots Configuration
The Independent Channel Mode is the default Maximum Performance Mode preferred for
Intel® Xeon® Processor 5500 series and Intel® Xeon® Processor 5600 series based
platforms. All three channels may be populated in any order and have no matching
requirements. All channels must run at the same interface frequency, but individual
channels may run at different DIMM timings (RAS latency, CAS latency, and so forth).
Memory Sparing and Mirroring
The spare mode is not supported by Intel® Server System SR1690WB.
With memory mirroring, the system maintains two copies of all data in the memory
subsystem. If a DIMM fails, the data is not lost because the second copy of the data is
available from the mirrored DIMM in the opposite channel. The system will not fail due
to memory error unless both the primary and the mirrored copy of the data become corrupt
at the same time.
In a mirrored system, the maximum usable memory is one-half of the installed memory,
with a minimum of two DIMMs installed. Since the data is duplicated across DIMMs, it
means that up to one-half of the installed DIMMs are actively in use at any one time. The
remaining DIMMs are used for mirroring.
22
Intel® Server System SR1690WB Service Guide
See the Intel® Server System S5500WB Technical Product Specification for additional
information regarding the memory sub-system.
Power Supply
TThe Power supply in SR1690WB system provides 650W at maximum. The power
supply must provide a minimum of 2.6 A of 5V standby current or the board will not boot.
Optional Hardware
Intel® RAID Activation Key
If RAID 5 is needed, you can install the optional Intel® RAID Activation Key
AXXRAKSW5. To enable RAID 5, this activation key is placed on the SATA Key
connector located at the left side of the server board. For information on how to install the
Intel® RAID Activation Key AXXRAKSW5 accessory to enable RAID 5, see the
documentation that is included with the accessory kit.
Intel® Remote Management Module 3
The RMM3 advanced management board serves two purposes. The first is to give the
customer the option to add a dedicated management 100-Mbit LAN interface to the
product. The second is to give additional flash space, enabling the Advanced Management
functions to support WS-MAN and CIMOM. The RMM3 comes with a third 10/100GbE
NIC that connects to the board. RMM3 management traffic can use the third NIC or NIC
1.
To install the RMM3 module, following the instruction in the RMM3 kit package, which
is purchased separately.
Intel® Server System SR1690WB Service Guide
23
Intel® I/O Expansion Module
The Intel® Server System SR1690WB supports a variety of I/O Module options using 2x4
PCI Express* Gen2 Intel® I/O Expansion Module connectors on the rear of the server
board. It accommodates both the double-wide I/O expansion modules and the PCI
Express* Gen 1 I/O modules. Below is the list of supported I/O modules on SR1690WB:
Table 5. List of Supported I/O Modules on SR1690WB
Product Code
24
Description
AXX4SASMOD
Intel® SAS Entry RAID I/O Expansion
Module: Provides 4-port pass through
SAS, entry-level RAID 0/1/1E, and
optional host RAID (4 internal ports).
AXXGBIOMOD
Dual Gigabit Ethernet I/O Expansion
Module
AXXROMBSASMR
Intel® Integrated RAID I/O Expansion
Module: Provides four internal ports,
full-featured SAS / SATA RAID 0,1,5,6
and striping capability for spans 10, 50,
60. You must order the optional backup
battery AXXRSBBU3 separately.
AXXSASIOMOD
External 4-port SAS I/O Expansion
Module.
AXX10GBIOMOD
Dual-port 10 Gigabit Ethernet I/O
Expansion Module with CX4
connectors.
AXX4GBIOMOD2
Quad port Gigabit Ethernet I/O
Expansion Module based on the Intel®
82576EB Gigabit Ethernet Controller.
AXXIBQDRMOD
InfiniBand* I/O Expansion Module
Single Port QDR.
Intel® Server System SR1690WB Service Guide
3
Hardware Installations and Upgrades
Before You Begin
Before working with your server product, pay close attention to the “Safety Information”
at the beginning of this manual.
Note: Whenever you service the system, you must first power down the server and unplug all
peripheral devices and the AC power cord.
Tools and Supplies Needed
•
•
•
•
Phillips* (cross head) screwdrivers (#1 bit and #2 bit)
Needle nosed pliers
Pen or pencil
Antistatic wrist strap and conductive foam pad (recommended)
System References
All references to the left, right, front, top, and bottom assume the reader is facing the front
of the server system as it would be positioned for normal operation.
Removing and Installing the System Cover
Removing the System Cover
You must operate the server system with the system cover in place to ensure proper
cooling. You must remove the top cover to add or replace components inside of the server.
None of the internal components are hot-swappable. Before you remove the server system
cover, power down the server and unplug all peripheral devices and the AC power cable.
Note: You may need a non-skid surface or a stop behind the server system to prevent the server
system from sliding on your work surface.
1. Remove the top cover screw (see letter “A”).
2. Loosen the screw at the rear of the chassis (see letter “B”).
3. Push rearward on the blue grip point at the front of the server.
25
4. Slide the cover back until it stops and then lift the cover upward to remove it. See
letter “C”.
B
C
A
al
tic e
Op evic
D
AF003222
Figure 13. Removing the Server System Cover
Installing the System Cover
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information”.
2. Place the cover over the server system so that the side edges of the cover sit just
inside the server system sidewalls. Slide the cover forward (see letter “A” in
Figure 14).
3. Tighten the screw at the rear of the server (see letter “B”) and install the two screws
at the front of the server (see letter “C”).
26
Intel® Server System SR1690WB Service Guide
B
A
C
al
tic e
Op evic
D
AF003223
Figure 14. Installing the Server System Cover
Removing and Installing the Processor Air Duct
The system requires the use of an air duct to direct airflow and sustain appropriate air
pressure. Always operate your server system with the air duct in place. The air duct is
required for proper airflow within the server system.
Removing the Processor Air Duct
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information”.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the System
Cover”.
4. Lift the processor air duct from its location behind the two system blower fans.
Intel® Server System SR1690WB Service Guide
27
al
tic e
Op evic
D
AF003224
Figure 15. Removing the Processor Air Duct
Installing the Processor Air Duct
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information”.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the System
Cover”.
4. Lower the air duct into place; align the air duct side walls to the corresponding slots
on the bracket behind the four system blower fans and insert into position. Use
caution not to pinch or disengage cables that may be near or under the air duct.
28
Intel® Server System SR1690WB Service Guide
al
tic e
Op evic
D
AF003225
Figure 16. Installing the Processor Air Duct
Installing and Removing Memory
The silkscreen on the board for the DIMMs displays DIMM_A1, DIMM_A2, DIMM_B1,
and DIMM_B2, DIMM_D1, DIMM_D2, DIMM_E1, and DIMM_E2 starting from the
inside of the board. For two slots per channel configurations, the server board requires
DDR3 DIMMs within a channel to be populated starting with the DIMM farthest from the
processor. The DIMM farthest from the processor per channel is in blue on boards.
Installing DIMMs
To install DIMMs, follow these steps:
1. Observe the safety and ESD precautions at the beginning of this book.
2. Turn off all peripheral devices connected to the server.
3. Turn off the server.
4. Disconnect the AC power cord from the server.
Intel® Server System SR1690WB Service Guide
29
5. Remove the cover from the server and locate the DIMM sockets (see Figure 17).
C
E
D
B
A
AF003227
Figure 17. Installing the Memory
6. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the
open position (see letter “A” in Figure 17).
7. Holding the DIMM by the edges, remove it from its anti-static package.
8. Position the DIMM above the socket. Align the two small notches in the bottom
edge of the DIMM with the keys in the socket (see letter “B” in Figure 17).
9. Insert the bottom edge of the DIMM into the socket (see letter “C” in Figure 17).
10. When the DIMM is inserted, push down on the top edge of the DIMM until the
retaining clips snap into place (see letter “D” in Figure 17). Make sure the clips are
firmly in place (see letter “E” in Figure 17).
11. Replace the server’s cover and reconnect the AC power cord.
Removing DIMMs
To remove a DIMM, follow these steps:
1. Observe the safety and ESD precautions at the beginning of this book.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Remove the AC power cord from the server.
4. Remove the server's cover.
5. Gently spread the retaining clips at each end of the socket. The DIMM lifts from
the socket.
6. Holding the DIMM by the edges, lift it from the socket, and store it in an anti-static
package.
30
Intel® Server System SR1690WB Service Guide
7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM
sockets.
8. Replace the server's cover and reconnect the AC power cord.
Installing or Replacing the Processor
Note: Use the following instructions to install or replace a processor instead of using the
instructions that came with the processor.
Caution: Processor must be appropriate: If you install a processor that is inappropriate for your
server, you may damage the server board. See “Server System References” for a link to
the list of compatible processor(s).
ESD and handling processors: Reduce the risk of electrostatic discharge (ESD) damage
to the processor by doing the following: (1) Touch the metal chassis before touching the
processor or server board. Keep part of your body in contact with the metal chassis to
dissipate the static charge while handling the processor. (2) Avoid moving around
unnecessarily.
Installing the Processor
To install a processor, follow these instructions:
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” for more information.
2. Turn off all peripheral devices connected to the server and turn off the server.
3. Disconnect the AC power cord from the server.
4. Remove the server's cover. See the document that came with your server chassis for
instructions on removing the server's cover.
5. Locate the processor socket and open the socket lever (see Figure 18).
A
B
AF003228
Figure 18. Lifting the Load Lever
6. Open the load plate (see letter “A” in Figure 18 and letter “B” in Figure 18).
Intel® Server System SR1690WB Service Guide
31
A
B
AF003229
Figure 19. Open the Load Plate
7. Remove the socket protective cover (see Figure 19).
8. Take the processor out of the box and remove the protective shipping cover
(Figure 20).
AF003292
Figure 20. Removing the socket
32
Intel® Server System SR1690WB Service Guide
Note: Do not touch the socket pins; they are very sensitive and easily damaged.
9. Align the processor cutouts to match the two socket pins, and then insert the
processor into the socket as shown in Figure 21.
B
A
AF003293
Figure 21. Aligning the Processor
10. Close the load plate (see the letter “A” in Figure 22), close the socket lever and
ensure the load plate tab engages under the socket lever when fully closed. (See
letter “B” and “C” in Figure 22)
C
A
B
AF003294
Figure 22. Close the Load Plate and Socket Lever
Note: Make sure the alignment triangle mark and the alignment triangle cutout align correctly.
To assist in package orientation and alignment with the socket:
Intel® Server System SR1690WB Service Guide
33
Installing the Heat Sink(s)
1. If a protective film covers the thermal interface material (TIM) on the underside of
the heat sink, remove the protective film.
2. Align heat sink fans to the front and back of the chassis for correct airflow. Airflow
goes from front-to-back of chassis.
3. Each heat sink has four captive fasteners and should be tightened as shown.
4. Using a #2 Phillips* screwdriver, finger-tighten each fastener diagonally according
to the white-circled numbers (see Figure 23).
5. Securely re-tighten each fastener again in the same order as performed in Step 4.
6. Attach fan power cable to server board as shown below.
C
3
2
A
B
1
4
AF003295
Figure 23. IU Reference Heat sink Assembly
7. Reinstall and reconnect any parts you removed or disconnected to reach the
processor sockets.
8. Replace the server’s cover and reconnect the AC power cord. See the
documentation that came with your server chassis for instructions on installing the
server’s cover.
Replacing a Processor
1. Observe the safety and ESD precautions at the beginning of this book.
2. Turn off all peripheral devices connected to the server. Turn off the server.
34
Intel® Server System SR1690WB Service Guide
3. Remove the AC power cord from the server.
4. Remove the server's cover.
5. Unplug the processor fan cable from the server board.
6. Loosen the four captive screws on the corners of the heat sink.
7. Twist the heat sink slightly to break the seal between the heat sink and the
processor.
8. Lift the heat sink from the processor. If it does not pull up easily, twist the heat sink
again. Do not force the heat sink from the processor. Doing so could damage the
processor.
9. Lift the processor lever.
10. Raise the CPU load plate.
11. Remove the processor.
12. If installing a replacement processor, see “Installing the Processor”. Otherwise,
install the protective socket cover over the empty processor socket and reinstall the
chassis cover.
Installing and Removing a Hot-swap Hard Drive
You can install up to two fixed SATA drives in the Intel® Server System SR16WB90
Service Guide. See “Server System References” for a link to a list of supported hardware.
Caution: If you install less than four drives or devices, the empty drive bays must be occupied by
carriers with drive blanks to maintain proper system cooling.
To avoid possible damage to your server system, use only the drive carriers that came
with your system.
Installing a SAS or SATA Hot-swap Hard Disk Drive
Note: The server system does not support all hard drives. See “Server System References” for a
link to a list of supported hardware.
1. Open the latch at the front of the hard drive carrier (see letter “A”).
2. Pull out on the black lever and slide the carrier from the server system (see letter
“B”).
Intel® Server System SR1690WB Service Guide
35
A
B
AF003302
Figure 24. Pulling out the back lever
3. Remove the hard drive from its wrapper and place it on an antistatic surface.
4. Set any jumpers and/or switches on the drive according to the drive manufacturer's
instructions.
5. With the drive circuit-side down, position the connector end of the drive so that it is
facing the rear of the drive carrier.
6. Align the holes in the drive to the holes in the drive carrier and attach it to the
carrier with the screws that were attached to the drive blank.
B
A
AF003303
Figure 25. 2.5 HDD Installation
36
Intel® Server System SR1690WB Service Guide
A
B
AF003304
Figure 26. 3.5 HDD Installation
7. With the black lever in the fully open position, slide the drive assembly into the
server system. The green latch at the front of the drive carrier must be to the right.
Do not push on the black drive carrier lever until the lever begins to close by itself.
8. When the black drive carrier lever begins to close by itself, push on it to lock the
drive assembly into place.
A
B
AF003305
Figure 27. Locking the drive assembly
Intel® Server System SR1690WB Service Guide
37
Removing a SAS or SATA Hot-swap Hard Disk Drive
1. Press in on the green latch at the front of the hard drive carrier. and pull out on the
black lever to slide the carrier from the server system.
2. Remove the four screws that attach the hard drive to the drive carrier. Lift the drive
from the carrier and store the drive in an anti-static bag.
3. With the black lever in the fully open position, slide the drive carrier into the server
system. The green latch must be to the right. Do not push on the black lever until
the lever begins to close by itself.
Note: All hard drive carriers must be installed in the server system and populated
either with a drive or without a drive to maintain system thermals.
4. When the black lever begins to close by itself, push on it to lock the drive carrier
into place.
Installing or Removing a Slimline Optical Drive
Caution: Slimline optical drives are NOT hot-swappable. Before removing or replacing the drive,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
To maintain proper system cooling, if you do not install a device at this location, you must
install the provided filler blank.
Installing a Slimline Optical Drive
1. Remove the slimline drive bay filler blank, if installed.
38
Intel® Server System SR1690WB Service Guide
AF003311
Figure 28. Removing the Knockout in Bezel for Optical Opening
2. Obtain the optical drive, and the optical drive latch from system package.
3. Screw the latch to the optical drive, and plug in the composed SATA/SATA Power
cable, which is shipped in system package.
B
A
AF003312
Figure 29. Attaching the Brackets to the Optical Drive
4. Lead the SATA/SATA Power cable through the optical drive bay before inserting
the drive.
Intel® Server System SR1690WB Service Guide
39
5. Slide the optical drive assembly in through the front of the chassis, as shown by
letter “A in the following figure. The assembly will automatically be locked if the
drive assembly is in position.
B
A
AF003313
6. Connect the SATA cable connector to SATA port 4 or 5 on server board.
7. Connect the SATA power connector to P6 connector from system power supply.
B
al
tic e
Op evic
D
A
AF003314
Figure 30. Installing the Optical Drive into the Server System
40
Intel® Server System SR1690WB Service Guide
Removing a Slimline Optical Drive
1. Disconnect the SATA power from system power supply and SATA cable connector
from server board.
2. Press the optical latch and slide the optical drive assembly out of the chassis.
3. Install slimline drive bay filler blank, if no optical drive installed.
Installing and Removing the PCI Riser Assembly
Removing the PCI Riser Assembly
1. Disconnect any cables attached to any add-in cards.
2. Grasp the riser assembly and pull up to release it from the system.
AF003322
Figure 31. Removing the PCI Riser Assembly from the Server System
Installing the PCI Riser Assembly
1. Lower the riser assembly into place (see letter “A”).
2. Align the two hooks in the riser assembly with the matching slots at the back of the
server system (see letter “B”).
Intel® Server System SR1690WB Service Guide
41
A
B
AF003323
Figure 32. Installing the PCI Riser Assembly
3. Press down uniformly until the two hooks on the rear of the PCI riser assembly
engage the server system back panel slots. The riser card will seat into the matching
socket on the server board. Ensure the riser card is fully seated.
Installing and Removing a PCI Add-In Card
The following instructions describe how to install and remove a PCI add-in card.
Installing a PCI Add-In Card
Peripherals and add-in cards are not included in your system. You must purchase them
separately. The riser card supports a full-height or low-profile PCI Express* 2.0 x8 add-in
card.
1. After removing the PCI riser assembly from the server system, remove the screw
that attaches the PCI bracket shield to the rear of the chassis to remove the shield.
Retain the screw.
2. Insert the PCI card edge connector in the slot on the PCI riser.
42
Intel® Server System SR1690WB Service Guide
A
B
C
AF003324
Figure 33. Installing a PCI Card in a Riser Card
3. Insert the riser card with the attached PCI card into the PCI slot on the server board.
Press firmly on the riser card until it is fully seated. Be sure to press down on the
riser card, not on the PCI card.
Caution: Press the riser card straight down into the slot. Tipping the riser card while installing into
the slot may damage the riser card or slot on the server board.
4. Use the screw removed in step 1 to secure the riser card assembly to the chassis.
Removing a PCI Add-In Card
1. Remove the screw holding the add-in card in place (see letter “A”).
2. Remove the PCI add-in card from the riser card connector (see letter “B”).
B
A
AF003325
Figure 34. Removing a PCI Card in a Riser Card
Intel® Server System SR1690WB Service Guide
43
Removing and Installing the System Fans
Caution: The system fans are NOT hot-swappable. Before removing or replacing, you must first
take the server out of service, turn off all peripheral devices connected to the system, turn
off the system by pressing the power button, and unplug the AC power cord from the
system or wall outlet.
Note: The fans that are integrated into the power supply cannot be replaced separately. If one of
the fans in the power supply fails, you must replace the power supply.
The system fans are located in the front of the server system, which you can individually
replace if one of them fails. If a fan in the power supply fails, you must replace the power
supply. Use the following steps to replace a system fan.
Replacing the System Fans
1. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct”.
44
Intel® Server System SR1690WB Service Guide
B
ti
Op
D
A
Fan 1
A
Fan 2
Fan 3
1
2
3
Fan 4
4
AF003309
Figure 35. Replacing the system fans
2. Disconnect the two 4-pin or one 8-pin system fan cables from the server board. See
letters “2” in the following figure.
3. Lift the failed fan from the module.
4. Remove the plastic screws from the failed fans and install them into the new fans.
Intel® Server System SR1690WB Service Guide
45
AF003308
Figure 36. Remove the screws from the fans
5. Position the replacement fan so the connector on the fan is at the right and pointing
down.
6. With the fan oriented correctly, insert the fan into the fan module (see letter “3”),
and insert the fan cable into the matching connector on the server board. (see letter
“2”).
46
Intel® Server System SR1690WB Service Guide
A
ti
Op
D
B
Fan 1
B
Fan 2
Fan 3
1
2
3
Fan 4
4
AF003310
Figure 37. Inserting the fan into the fan module
Installing and Removing the I/O Expansion Module(s)
Installing the I/O Expansion Module(s)
1. Squeeze the sides of the I/O expansion module cover to disengage it from the server
system back panel and remove it (see letter “A”).
Intel® Server System SR1690WB Service Guide
47
al
tic e
Op evic
D
A
AF003317
Figure 38. Installing the I/O Expansion Module(s)
2. Attach the standoffs to the server board (see letter “A”) and attach the I/O shield
gasket to the module (see letter “B”).
3. Attach the I/O expansion module(s) to the server board (see letter “C”).
48
Intel® Server System SR1690WB Service Guide
A
C
B
al
tic e
Op evic
D
AF003318
Figure 39. Attaching the I/O Expansion Module(s)
Removing the I/O Expansion Module(s)
1. Remove the I/O expansion module(s) from the server board (see letter “A”).
2. Remove the standoffs from the server board (see letter “B”).
3. Install the I/O expansion module cover into the system back panel (see letter “C”).
Intel® Server System SR1690WB Service Guide
49
Installing and Removing the Intel® Remote
Management Module 3 and the Intel® RMM 3 NIC
Installing the Intel® RMM3 and Intel® RMM3 NIC
1. Squeeze the sides of the Intel®RMM3 NIC module cover to disengage it from the
server system back panel and remove it (see letter “A”)
A
al
tic e
Op evic
D
AF003315
Figure 40. Installing the Intel® RMM3 and Intel® RMM3 NIC
2. Attach the bracket of Intel® RMM3 NIC module by two screws (see letter “A”).
3. Connect the Intel® RMM3 cable to the slot on server board (see letter “B”).
4. Attach the Intel® RMM3 module to rear chassis by two screws (see letter “C”).
50
Intel® Server System SR1690WB Service Guide
B
A
C
al
tic e
Op evic
D
AF003316
Figure 41. Attach the Intel® RMM3 module to rear chassis
Removing the Intel® RMM3 and Intel® RMM3 NIC
Use the reverse steps to remove the Intel® RMM3 module
1. Remove the two screws from rear chassis to loosen Intel® RMM3 board (see letter
“C”).
2. Plug out Intel® RMM3 NIC module cable from the server board (see letter “B”).
3. Install the Intel® RMM3 NIC module cover into the system back panel (see letter
“A”).
Replacing the Backplane Board
The instructions below describe how to replace the backplane board in the system.
Intel® Server System SR1690WB Service Guide
51
Removing the Backplane Board
1. Disengage hard drives from the backplane board (see letter “A”).
2. Disconnect all cables from the backplane board.
3. Remove two screws on the top of backplane bracket (see letter “B”).
4. Pull out the backplane assembly vertically from the chassis (see letter “C”).
B
C
al
tic e
Op evic
D
A
AF003300
Figure 42. Removing the backplane board
Installing the Backplane Board
1. Lower the backplane assembly into the system (see letter “A”) and fix the
backplane assembly into fix position, aligning with two screw holes on chassis.
2. Tighten two screws to lock the backplane assembly in position (see letter “B”).
3. Connect data/power cables to the backplane connectors.
4. Engage hard drives back to the backplane (see letter “C”).
52
Intel® Server System SR1690WB Service Guide
B
A
al
tic e
Op evic
D
C
AF003301
Figure 43. Installing the backplane board
Replacing the Server Board
Removing the Server Board
1. Remove the system air duct.
2. If installed, remove the memory, processor heat sinks, and processors from the
server.
3. If installed, remove the PCI riser assembly.
4. If installed, disconnect all SATA cables from the server board.
5. Disconnect the system fans cables from server board.
6. Disconnect all power cables coming from the power supply to the server board.
Intel® Server System SR1690WB Service Guide
53
7. Remove the nine screws from the server board (see letter “A”) and lift the server
board from the server system (see letter “B”).
A
B
al
tic e
Op evic
D
AF003297
Figure 44. Removing the Server Board
8. Install the replacement server board. See “Installing the Server Board” on page -54.
Installing the Server Board
1. Place the server board into the server system as shown in the following figure (see
letter “A”).
2. Attach the server board with nine screws (see letter “B”).
54
Intel® Server System SR1690WB Service Guide
B
A
al
tic e
Op evic
D
AF003298
Figure 45. Installing the Server Board
3. Re-connect all power cables coming from the power supply to the server board.
4. Re-connect the system fan cables to server board.
5. Re-connect all SATA cables to the server board.
6. Install the PCI riser assembly.
7. Install the memory, processor heat sinks, and processors.
8. Install the system air duct.
Intel® Server System SR1690WB Service Guide
55
Replacing the Backup Battery
The lithium battery on the server board powers the RTC for up to 10 years in the absence
of power. When the battery starts to weaken, it loses voltage, and the server settings stored
in CMOS RAM in the RTC (for example, the date and time) may be wrong. Contact your
customer service representative or dealer for a list of approved devices.
Warning: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the equipment manufacturer. Discard used batteries
according to manufacturer's instructions.
Advarsel: Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med
batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.
Advarsel: Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av
apparatfabrikanten. Brukt batteri returneres apparatleverandøren.
Varning: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ
som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens
instruktion.
Varoitus: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan
laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
56
Intel® Server System SR1690WB Service Guide
1. Observe the safety and ESD precautions at the beginning of this book.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord from the server.
4. Remove the server's cover and locate the battery.
5. Insert the tip of a small flat bladed screwdriver, or an equivalent, under the tab in
the plastic retainer. Gently push down on the screwdriver to lift the battery.
6. Remove the battery from its socket.
AF003299
Figure 46. Replacing the Backup Battery
7. Dispose of the battery according to local ordinance.
8. Remove the new lithium battery from its package, and, being careful to observe the
correct polarity, insert it in the battery socket.
9. Close the chassis.
10. Run Setup to restore the configuration settings to the RTC.
Replacing the Power Supply
Caution: The power supply is not hot-swappable. Before removing or replacing the power supply,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
Removing the Power Supply
You can replace the power supply if it fails or if one of the fans integrated into it fails. To
replace the power supply, use the following instructions.
Intel® Server System SR1690WB Service Guide
57
1. Disconnect all power supply cables including power at rear of chassis (see letter
“A”).
2. Remove the three screws securing the power supply to the back panel (see letter
“B”).
A
B
B
D
C
AF003319
Figure 47. Removing the Power Supply from the Server System
3. Lift the power supply up to clear the chassis tab (see letter “C”) and remove the
power supply by sliding it out (see letter “D”).
Installing the Power Supply
1. Insert the replacement power supply by first engaging the back panel (see letter
“A”).
58
Intel® Server System SR1690WB Service Guide
2. Lower the front of the power supply into place behind the chassis tab (see letter
“B”).
D
C
C
A
B
AF003320
Figure 48. Installing the Power Supply into the Server System
3. Secure the power supply to the back panel with three screws (see letter “C”).
4. Connect all cables, including the power at the rear of the chassis (see letter “D”).
Installing and Removing the Rack Handles
Installing the Rack Handles
1. Align the rack handle with the holes on the side of the server system and attach the
rack handle with the three screws.
Intel® Server System SR1690WB Service Guide
59
AF003326
Figure 49. Installing the Rack Handle
2. Repeat step 1 on the opposite side of the server.
Removing the Rack Handles
1. Remove the three screws holding the rack handle in place, and remove the rack
handle from the server system.
AF003327
Figure 50. Removing the Rack Handle
60
Intel® Server System SR1690WB Service Guide
4
Server Utilities
Using the BIOS Setup Utility
This section describes the BIOS Setup Utility options, which is used to change server
configuration defaults. You can run the BIOS Setup with or without an operating system
being present. See “Server System References” for a link to the Intel® Server Board
S5500WB Technical Product Specification where you can find details about specific
BIOS setup screens.
Starting Setup
You can enter and start BIOS Setup under several conditions:
• When you turn on the server, after POST completes the memory test.
• When you have moved the CMOS jumper on the server board to the “Clear CMOS”
position (enabled).
In the two conditions listed above, during the Power On Self Test (POST), you will see
this prompt:
Press <F2> to enter SETUP
In a third condition, when CMOS/NVRAM is corrupted, you will see other prompts but
not the <F2> prompt:
Warning: CMOS checksum invalid
Warning: CMOS time and date not set
In this condition, the BIOS loads default values for CMOS and attempts to boot.
If You Cannot Access Setup
If you cannot access BIOS Setup, you might need to clear the CMOS memory. For
instructions on clearing the CMOS, see “Clearing the CMOS“.
Setup Menus
Each BIOS Setup menu page contains a number of features. Except for those features that
are provided only to display automatically configured information, each feature is
associated with a value field that contains user-selectable parameters. If a user has
adequate security rights, they can change these parameters. If a value cannot be changed
for any reason, the feature's value field is inaccessible.
61
“Setup Menu Key Use” describes the keyboard commands you can use in the BIOS Setup
menus.
Table 6. Setup Menu Key Use
Key to Press
Description
<F1>
Pressing <F1> on any menu launches the general help window.
Left and right arrows
The left and right arrow keys are used to move between the major menu
pages. The keys have no effect if a submenu or pick list is displayed.
Up arrow
Select Item up - The up arrow is used to select the previous value in a
menu item's option list, or a value field pick list. Pressing <Enter>
activates the selected item.
Down arrow
Select Item down - The down arrow is used to select the next value in a
menu item's option list, or a value field pick list. Pressing <Enter>
activates the selected item.
<F5> or <->
Change Value - The minus key or <F5> function key is used to change
the value of the current item to the previous value. This key scrolls
through the values in the associated pick list without displaying the full
list.
<F6> or <+>
Change Value - The plus key or <F6> function key is used to change the
value of the current menu item to the next value. This key scrolls through
the values in the associated pick list without displaying the full list. On
106-key Japanese keyboards, the plus key has a different scan code
than the plus key on the other keyboard, but it has the same effect.
<Enter>
Execute Command - The <Enter> key is used to activate submenus
when the selected feature is a submenu, or to display a pick list if a
selected feature has a value field, or to select a sub-field for multi-valued
features like time and date. If a pick list is displayed, the <Enter> key will
undo the pick list, and allow another selection in the parent menu.
<Esc>
Exit - The <Esc> key provides a mechanism for backing out of any field.
This key will undo the pressing of the <Enter> key. When the <Esc> key
is pressed while editing any field or selecting features of a menu, the
parent menu is re-entered. When the <Esc> key is pressed in any
submenu, the parent menu is re-entered. When the <Esc> key is
pressed in any major menu, the exit confirmation window is displayed
and the user is asked whether changes can be discarded.
<F9>
Setup Defaults - Pressing <F9> causes the following to display:
Setup Confirmation
Load default configuration now?
[Yes] [No]
If “Yes” is selected and <Enter> is pressed, all Setup fields are set to
their default values. If “No” is selected and the <Enter> key is pressed, or
if <Esc> is pressed, the user is returned to where they were before <F9>
was pressed without affecting any existing field values.
62
Intel® Server System SR1690WB Service Guide
Table 6. Setup Menu Key Use
Key to Press
<F10>
Description
Save and Exit - Pressing <F10> causes the following message to
display:
Setup Confirmation
Save Configuration changes and exit now?
[Yes] [No]
If “Yes” is selected and <Enter> is pressed, all changes are saved and
Setup is exited. If “No” is selected and <Enter> is pressed, or if <Esc> is
pressed, the user is returned to where they were before <F10> was
pressed without affecting any existing values.
Upgrading the BIOS
The upgrade utility allows you to upgrade the BIOS in flash memory. The code and data in
the upgrade file include the following:
• On-board system BIOS, including the recovery code, BIOS Setup Utility, and
strings.
• On-board video BIOS, and other option ROMs for devices embedded on the server
board.
• OEM binary area
• Microcode
• A way to change the BIOS language
Preparing for the Upgrade
The following steps explain how to prepare to upgrade the BIOS, including how to record
the current BIOS settings and how to obtain the upgrade utility.
In the unlikely event a BIOS error occurs during the BIOS upgrade process, you may need
to follow a recovery process to return the system to service. For additional information,
see “Server System References” for a link to the necessary firmware and BIOS updates
software and instructions.
Recording the Current BIOS Settings
1. Boot the computer and press <F2> when you see the message:
Press <F2> Key if you want to run SETUP
2. Write down the current settings in the BIOS Setup program.
Note: Do not skip step 2. You need these settings to configure your server at the end of the
procedure.
Intel® Server System SR1690WB Service Guide
63
Obtaining the Upgrade
Download the BIOS image file to a temporary folder on your hard drive. See “Server
System References” for a link to the update software.
Note: Review the instructions and release notes provided in the readme file distributed with the
BIOS image file before attempting a BIOS upgrade. The release notes contain critical
information regarding jumper settings, specific fixes, or other information to complete the
upgrade.
Upgrading the BIOS
Download the BIOS image file to a temporary folder on your hard drive. See “Server
System References” for a link to the update software.
Caution: Do not power down the system during the BIOS update process! The system resets
automatically when the BIOS upgrade process completes. Doing so may corrupt the
system BIOS.
Note: You may encounter a CMOS Checksum error or other problem after reboot. If this
happens, shut down the system and boot it again. CMOS checksum errors require that you
enter Setup, check your settings, save your settings, and exit Setup.
Clearing the CMOS
If you cannot access the BIOS setup screens, you must use the CMOS Clear jumper to
reset the configuration RAM. The CMOS Clear jumper is located on jumper block at J1B4
on the server board.
1. Power down the system; do not disconnect the AC power.
2. Open the server.
3. Move the jumper from the normal operation position, at pins 1 and 2 to the CMOS
Clear Force Erase position, covering pins 2 and 3.
64
Intel® Server System SR1690WB Service Guide
CMOS Clear
J1B4
1-2: Default
2
3
2-3: Clear CMOS
BMC Force Update
J1B5
1-2: Default
2
3
2-3: Enabled
Password Clear
J1C2
1-2: Default
2
3
2-3: Password Clear
AF003214
Figure 51. CMOS Recovery Jumper
4. Reconnect the AC power and power up the system.
5. When the system begins beeping, power it down and disconnect the AC power.
6. Return the CMOS Clear jumper to the spare location, covering pins 1 and 2.
7. Close the server chassis; reconnect the AC power and power up the system.
8. The CMOS is now cleared and you can reset it by going into the BIOS setup.
Resetting the Password
If the user or administrator password(s) is lost or forgotten, moving the password reset
jumper into the “clear” position clears both passwords. Before you can set a new
password(s), you must restore the password reset jumper to its original position. The
password clear jumper is located on jumper block at location J1C2 on the server board.
1. Power down the system and disconnect the AC power.
2. Open the server chassis.
3. Move the jumper from the normal operation position, Password Clear Protect, at
pins 1 and 2 to the Password Clear Erase position, covering pins 2 and 3.
Intel® Server System SR1690WB Service Guide
65
4. Reconnect the AC power; power up the system.
5. Power down the system and disconnect the AC power.
6. Return the Password Reset jumper to the Password Protect position, covering pins
1 and 2. Reconnect AC power and power up the server.
7. The password is now cleared and you can reset it by going into the BIOS setup.
CMOS Clear
J1B4
1-2: Default
2
3
2-3: Clear CMOS
BMC Force Update
J1B5
1-2: Default
2
3
2-3: Enabled
Password Clear
J1C2
1-2: Default
2
3
2-3: Password Clear
AF003214
Figure 52. Password Recovery Jumper
66
Intel® Server System SR1690WB Service Guide
Appendix A:
Technical Reference
650-W Single Power Supply Input Voltages
• 100-127V at 47/63 Hz; 8.6 A max.
• 200-240V at 47/63 Hz; 4.3 A max.
650-W Single Power Supply Output Voltages
The following table lists the total wattage available from the power subsystem for each
voltage. Ensure your loads do not exceed the combined total wattage of 650 W. For
information about calculating the power usage for your configuration, see “Power Budget
Tool.”
Table 7. 650-W Single Power Supply Output Voltages
Voltage
Maximum Continuous
+3.3 V
13.8A
+5 V
19.6A
+12 V1
11.3A
+12 V2
11.3A
+12 V3
9.1A
+12 V4
9.1A
-12 V
0.43A
+5 VSB
3.0A
1. Maximum continuous total DC output power should not exceed 650 watts.
2. Peak load on the combined 12V output shall not exceed 52A peak.
3. Maximum continuous load on the combined 12V output shall not exceed 47A
4. Peak total DC output power should not exceed 700 Watts peak.
5. Peak power and peak current loading shall be supported for a minimum of 12
seconds.
6. Combined 3.3V & 5V power shall not exceed 150W.
67
System Environmental Specifications
Table 8. System Environmental Specifications
Temperature
Non-operating
-40 ° to +70 °C.
Operating
10° C to 35° C (50° F to 90° F) with the maximum rate of change not to
exceed 10° C per hour
Humidity
Non-operating
90% relative humidity (non-condensing) at 35°C.
Shock
Operating
2.0 g, 11 msec, 1/2 sine
Unpackaged
Trapezoidal, 25 g, velocity change 136 inches/sec
Packaged
Non-palletized free fall at a height of 30 inches
Acoustic noise
Sound Pressure: 55 dBA (rack mount) in an idle state at typical office
ambient temperature. (23 +/- degrees C) Sound Power: 7.0 BA in an idle
state at typical office ambient temperature. (23 +/- 2 degrees C).
Electrostatic
discharge (ESD)*
+/-12 kV except I/O port +/-8 KV, per Intel Environmental Test Specification.
*The system requires the use of a shielded LAN cable to comply with Immunity
regulatory requirements. Use of non-shield cables may result in the product having
insufficient protection against electromagnetic effects, which may cause improper
operation of the product.
68
Intel® Server System SR1690WB Service Guide
Appendix B:
Intel® Server Issue Report
Form
Note: For the fastest service, please submit your form via the Internet.
Date Submitted: _______________________________________________________
Company Name: ______________________________________________________
Contact Name: ________________________________________________________
Email Address: _______________________________________________________
Intel Server Product: ___________________________________________________
Priority (Critical, Hot, High, Low): _______________________________________
Brief Problem Description. Provide a brief description below. See the last page for space
to include a detailed problem description.
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
Board / Chassis Information
Baseboard Revision - PBA#: _____________________________________________
Baseboard Serial Number: _______________________________________________
CPU1 Speed/Stepping/Spec: _____________________________________________
CPU2 Speed/Stepping/Spec: _____________________________________________
System BIOS Version: __________________________________________________
HSC Firmware Version: _________________________________________________
Chassis Model: ________________________________________________________
Intel® Server System SR1690WB: __________________________________
69
Other (Vendor/Model):___________________________________________
DIMM Configuration
DIMM A1 MB and Vendor / part number: __________________________________
DIMM A2 MB and Vendor / part number: __________________________________
DIMM B1 MB and Vendor / part number: __________________________________
DIMM C1 MB and Vendor / part number: __________________________________
DIMM D1 MB and Vendor / part number: __________________________________
DIMM D2 MB and Vendor / part number: __________________________________
DIMM E1 MB and Vendor / part number: __________________________________
DIMM F1 MB and Vendor / part number: __________________________________
Operating System Information
Operating System:_____________________________________________________
Version: _____________________________________________________________
Service Pack:_________________________________________________________
70
Intel® Server System SR1690WB Service Guide
Add-in Card, Peripheral, Video, NIC
Check each box below as applicable, and provide the requested information:
Peripheral or Peripheral Description, Driver Revision, IRQ #, I/O Base Address, and FW
Peripheral
Description
Driver
Revision
IRQ
Make/Model
IRQ
FW
Revision
#
I/O Base
Address
FW
Revision
#
PCI Express*
Gen2 x8
On-board Video
Add-in Video
On-board NIC1 (10/
100/1000Mb/s)
On-board NIC2 (10/
100/1000Mb/s)
Intel® I/O
Expansion Module
Revision #NIC
Hard Drive Information
Drive Type (SATA/
SAS)
SATA_0
SATA_1
SATA_2
SATA_3
SATA_4
SATA_5
Management Information
On-Board Platform Instrumentation only ___________________________________
Intel® Remote Management Module _______________________________________
Intel® Server System SR1690WB Service Guide
71
Complete Problem Description
In the space below, provide a complete description of the steps used to reproduce the
problem or a complete description of where the problem can be found. Please also include
any details on troubleshooting already done.
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
72
Intel® Server System SR1690WB Service Guide
Appendix C: LED Decoder
During the system boot process, the BIOS executes a number of platform configuration
processes, each of which is assigned a specific hex POST code number. As each
configuration routine is started, the BIOS displays the POST code to the POST Code
Diagnostic LEDs on the back edge of the server board. To assist in troubleshooting a
system hang during the POST process, the Diagnostic LEDs can be used to identify the
last POST process that was executed.
Each POST code is represented by the Eight amber Diagnostic LEDs. The POST codes
are divided into two nibbles, an upper nibble and a lower nibble. The upper nibble bits are
represented by Diagnostic LEDs #4, #5, #6, #7. The lower nibble bits are represented by
Diagnostics LEDs #0, #1, #2 and #3. Given the bit is set in the upper and lower nibbles,
then corresponding LED is lit. If the bit is clear, corresponding LED is off.
The Diagnostic LED #7 is labeled as “MSB”, and the Diagnostic LED #0 is labeled with
“LSB”.
POST LED 7
POST LED 6
POST LED 5
POST LED 4
POST LED 0
POST LED 1
POST LED 2
POST LED 3
AF003321
Figure 53. Diagnostic LED Placement Diagram
Table 9. POST Progress Code LED Example
Upper Nibble LEDs
LEDs
Lower Nibble LEDs
MSB
LED
#7
LSB
LED
#6
LED
#5
LED
#4
LED
#3
LED
#2
LED
#1
LED
#0
73
Table 9. POST Progress Code LED Example
8h
4h
2h
1h
8h
4h
2h
1h
Status
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Results
1
0
1
0
1
1
0
0
Ah
Ch
• Upper nibble bits = 1010b = Ah; Lower nibble bits = 1100b = Ch; the two are
concatenated as ACh.
Table 10. Diagnostic LED POST Code Decoder
Diagnostic LED Decoder
Checkpoint
1 = On, 0= Off
Upper Nibble
Description
Lower Nibble
MSB
LED
LSB
8h
4h
2h
1h
8h
4h
2h
1h
#7
#6
#5
#4
#3
#2
#1
#0
Host Processor
0x10h
0
0
0
1
0
0
0
0
Power-on initialization of
the host processor
(bootstrap processor)
0x11h
0
0
0
1
0
0
0
1
Host processor cache
initialization (including AP)
0x12h
0
0
0
1
0
0
1
0
Starting application
processor initialization
0x13h
0
0
0
1
0
0
1
1
SMM initialization
0x14h
0
0
0
1
0
1
0
0
Selection of Processor
with least feature use as
Boot Strap Processor
0x15h
0
0
0
1
0
1
0
1
Switch an AP processor to
become the new Boot
Strap Processor
0
0
1
0
0
0
1
0
Initializing a chipset
component
Chipset
0x21h
Memory
74
Intel® Server System SR1690WB Service Guide
Table 10. Diagnostic LED POST Code Decoder
0x22h
0
0
1
0
0
0
1
0
Reading configuration
data from memory (SPD
on FBDIMM)
0x23h
0
0
1
0
0
0
1
1
Detecting presence of
memory
0x24h
0
0
1
0
0
1
0
0
Programming timing
parameters in the memory
controller
0x25h
0
0
1
0
0
1
0
1
Configuring memory
parameters in the memory
controller
0x26h
0
0
1
0
0
1
1
0
Optimizing memory
controller settings
0x27h
0
0
1
0
0
1
1
1
Initializing memory, such
as ECC init
0x28h
0
0
1
0
1
0
0
0
Testing memory
0xE4h
1
1
1
0
0
1
0
0
BIOS cannot
communicate with DIMM
(serial channel hardware
failure
0xE6h
1
1
1
0
0
1
1
0
DIMM(s) failed Memory
iBIST or Memory Link
Training failure
0xE8h
1
1
1
0
1
0
0
0
No memory available
(system halted)
0xE9h
1
1
1
0
1
0
0
1
Unsupported or invalid
DIMM configuration
(system halted)
0xEAh
1
1
1
0
1
0
1
0
DIMM training sequence
failed (system halted)
0xEBh
1
1
1
0
1
0
1
1
Memory test failed
(system halted)
0xECh
1
1
1
0
1
1
0
0
Unsupported or invalid
DIMM configuration
(system halted)
0xEDh
1
1
1
0
1
1
0
1
Unsupported or invalid
DIMM configuration
(system halted)
0xEBh
1
1
1
0
1
0
1
1
DIMM with corrupted SPD
data detected (system
halted)
Intel® Server System SR1690WB Service Guide
75
Table 10. Diagnostic LED POST Code Decoder
Intel® Quickpath Interconnect (QPI)
0xA0h
1
0
1
0
0
0
0
0
QPI Initialization
0xA1h
1
0
1
0
0
0
0
1
QPI Initialization
0xA2h
1
0
1
0
0
0
1
0
QPI Initialization
0xA3h
1
0
1
0
0
0
1
1
QPI Initialization
0xA4h
1
0
1
0
0
1
0
0
QPI Initialization
0xA5h
1
0
1
0
0
1
0
1
QPI Initialization
0xA6h
1
0
1
0
0
1
1
0
QPI Initialization
0xA7h
1
0
1
0
0
1
1
1
QPI Initialization
0xA8h
1
0
1
0
1
0
0
0
QPI Initialization
0xA9h
1
0
1
0
1
0
0
1
QPI Initialization
0xAAh
1
0
1
0
1
0
1
0
QPI Initialization
0xABh
1
0
1
0
1
0
1
1
QPI Initialization
0xACh
1
0
1
0
1
1
0
0
QPI Initialization
0xADh
1
0
1
0
1
1
0
1
QPI Initialization
0xAEh
1
0
1
0
1
1
1
0
QPI Initialization
0xAFh
1
0
1
0
1
1
1
1
QPI Initialization
Integrated Memory Controller (IMC)
76
0xB0h
1
0
1
1
0
0
0
0
Memory Initialization of
Integrated Memory
Controller
0xB1h
1
0
1
1
0
0
0
1
Memory Initialization of
Integrated Memory
Controller
0xB2h
1
0
1
1
0
0
1
0
Memory Initialization of
Integrated Memory
Controller
0xB3h
1
0
1
1
0
0
1
1
Memory Initialization of
Integrated Memory
Controller
0xB4h
1
0
1
1
0
1
0
0
Memory Initialization of
Integrated Memory
Controller
0xB5h
1
0
1
1
0
1
0
1
Memory Initialization of
Integrated Memory
Controller
Intel® Server System SR1690WB Service Guide
Table 10. Diagnostic LED POST Code Decoder
0xB6h
1
0
1
1
0
1
1
0
Memory Initialization of
Integrated Memory
Controller
0xB7h
1
0
1
1
0
1
1
1
Memory Initialization of
Integrated Memory
Controller
0xB8h
1
0
1
1
1
0
0
0
Memory Initialization of
Integrated Memory
Controller
0xB9h
1
0
1
1
1
0
0
1
Memory Initialization of
Integrated Memory
Controller
0xBAh
1
0
1
1
1
0
1
0
Memory Initialization of
Integrated Memory
Controller
0xBBh
1
0
1
1
1
0
1
1
Memory Initialization of
Integrated Memory
Controller
0xBCh
1
0
1
1
1
1
0
0
Memory Initialization of
Integrated Memory
Controller
0xBDh
1
0
1
1
1
1
0
1
Memory Initialization of
Integrated Memory
Controller
0xBEh
1
0
1
1
1
1
1
0
Memory Initialization of
Integrated Memory
Controller
0xBFh
1
0
1
1
1
1
1
1
Memory Initialization of
Integrated Memory
Controller
Intel® Server System SR1690WB Service Guide
77
Table 10. Diagnostic LED POST Code Decoder
PCI Bus
0x50h
0
1
0
1
0
0
0
0
Enumerating PCI buses
0x51h
0
1
0
1
0
0
0
1
Allocating resources to
PCI buses
0x52h
0
1
0
1
0
0
1
0
Hot Plug PCI controller
initialization
0x53h
0
1
0
1
0
0
1
1
Reserved for PCI bus
0x54h
0
1
0
1
0
1
0
0
Reserved for PCI bus
0x55h
0
1
0
1
0
1
0
1
Reserved for PCI bus
0x56h
0
1
0
1
0
1
1
0
Initializing USB host
controllers
0x57h
0
1
0
1
0
1
1
1
Detecting USB devices
0x58h
0
1
0
1
1
0
0
0
Resetting USB bus
0x59h
0
1
0
1
1
0
0
1
Reserved for USB devices
USB
ATA / ATAPI / SATA
0x5Ah
0
1
0
1
1
0
1
0
Resetting SATA bus and
all devices
0x5Bh
0
1
0
1
1
0
1
1
Detecting the presence of
ATA device
0x5Bh
0
1
0
1
1
1
0
0
Enable SMART if
supported by ATA device
0x5Bh
0
1
0
1
1
1
0
1
Reserved for ATA
0x5Eh
0
1
0
1
1
1
1
0
Resetting SMBUS
0x5Fh
0
1
0
1
1
1
1
1
Reserved for SMBUS
0
1
1
0
0
0
0
1
Initializing I/O Controller
Hub
0
1
1
0
0
0
1
1
Initializing Super I/O
1
1
1
0
0
0
0
Resetting the video
controller (VGA)
SMBUS
I/O Controller Hub
0x61h
Super I/O
0x63h
Local Console
0x70h
78
0
Intel® Server System SR1690WB Service Guide
Table 10. Diagnostic LED POST Code Decoder
0x71h
0
1
1
1
0
0
0
1
Disabling the video
controller (VGA)
0x72h
0
1
1
1
0
0
1
0
Enabling the video
controller (VGA)
0x73h
0
1
1
1
0
0
1
1
Reserved for video
controller (VGA)
Remote Console
0x78h
0
1
1
1
1
0
0
0
Resetting the console
controller
0x79h
0
1
1
1
1
0
0
1
Disabling the console
controller
0x7Ah
0
1
1
1
1
0
1
0
Enabling the console
controller
0x7Bh
0
1
1
1
1
0
1
1
Reserved for console
controller
Keyboard (only USB)
0x90h
1
0
0
1
0
0
0
0
Resetting the keyboard
0x91h
1
0
0
1
0
0
0
1
Disabling the keyboard
0x92h
1
0
0
1
0
0
1
0
Detecting the presence of
the keyboard
0x93h
1
0
0
1
0
0
1
1
Enabling the keyboard
0x94h
1
0
0
1
0
1
0
0
Clearing keyboard input
buffer
0x96h
1
0
0
1
0
1
0
1
Reserved for keyboard
Mouse (only USB)
0x98h
1
0
0
1
0
0
1
0
Resetting the mouse
0x99h
1
0
0
1
0
0
1
1
Detecting the mouse
0x9Ah
1
0
0
1
0
1
1
0
Detecting the presence of
mouse
0x9Bh
1
0
0
1
0
1
1
1
Enabling the mouse
0x9Ch
1
0
0
1
0
0
1
0
Reserved for mouse
0xA8h
1
0
1
0
1
0
0
0
Resetting the serial port
0xA9h
1
0
1
0
1
0
0
1
Disabling the serial port
0xAAh
1
0
1
0
1
0
1
0
Detecting the presence of
the serial port
Serial Port
Intel® Server System SR1690WB Service Guide
79
Table 10. Diagnostic LED POST Code Decoder
0xABh
1
0
1
0
1
0
1
1
Clearing serial port buffer
0xACh
1
0
1
0
1
1
0
0
Enabling serial port
0xADh
1
0
1
0
1
1
0
1
Reserved for serial port
0xB0h
1
0
1
1
0
0
0
0
Resetting fixed media
device
0xB1h
1
0
1
1
0
0
0
1
Disabling fixed media
device
0xB2h
1
0
1
1
0
0
1
0
Detecting presence of a
fixed media device (IDE
hard drive detection, and
so on)
0xB3h
1
0
1
1
0
0
1
1
Enabling / configuring a
fixed media device
0xB4h
1
0
1
1
0
1
0
0
Reserved for fixed media
Fixed Media
Removable Media
0xB8h
1
0
1
1
1
0
0
0
Resetting removable
media device
0xB9h
1
0
1
1
1
0
0
1
Disabling removable
media device
0xBAh
1
0
1
1
1
0
1
0
Detecting presence of a
removable media device
(IDE CDROM detection,
etc.)
0xBCh
1
0
1
1
1
1
0
0
Enabling / configuring a
removable media device
0xBDh
1
0
1
1
1
1
0
1
Reserved for removable
media device
Boot Device Selection (BDS)
80
0xD0
1
1
0
1
0
0
0
0
Entered the Boot Device
Selection phase (BDS)
0xD1
1
1
0
1
0
0
0
1
Return to last good boot
device
0xD2
1
1
0
1
0
0
1
0
Set up boot device
selection policy
0xD3
1
1
0
1
0
0
1
1
Connect boot device
controller
0xD4
1
1
0
1
0
1
0
0
Attempt flash update boot
mode
Intel® Server System SR1690WB Service Guide
Table 10. Diagnostic LED POST Code Decoder
0xD5
1
1
0
1
0
1
0
1
Transfer control to EFI
boot
0xD6
1
1
0
1
0
1
1
0
Trying boot device
selection
0xDF
1
1
0
1
1
1
1
1
Reserved for boot device
selection
Pre-EFI Initialization (PEI) Core
0xE0h
1
1
1
0
0
0
0
0
Entered Pre-EFI
Initialization phase (PEI)
0xE1h
1
1
1
0
0
0
0
1
Started dispatching early
initialization modules
(PEIM)
0xE2h
1
1
1
0
0
0
1
0
Initial memory found,
configured, and installed
correctly
0xE3h
1
1
1
0
0
0
1
1
Transfer control to the
DXE Core
0xF0h
1
1
1
1
0
0
0
0
Install PEIM for Platform
Status Codes
0xF1h
1
1
1
1
0
0
0
1
Detecting Platform Type
0xF2h
1
1
1
1
0
0
1
0
Early Platform
Initialization
0xF3h
1
1
1
1
0
0
1
1
PEI Modules initialized
PEI Modules
Driver Execution Environment (DXE) Core
0xE4h
1
1
1
0
0
1
0
0
Entered EFI driver
execution phase (DXE)
0xE5h
1
1
1
0
0
1
0
1
Started dispatching
drivers
0xE6h
1
1
1
0
0
1
1
0
Started connecting drivers
0xE7h
1
1
1
0
1
1
0
1
Waiting for user input
0xE8h
1
1
1
0
1
0
0
0
Checking password
0xE9h
1
1
1
0
1
0
0
1
Entering BIOS setup
0xEAh
1
1
1
0
1
1
0
0
Flash Update
0xEBh
1
1
1
0
1
1
0
1
Legacy Option ROM
Initialization
0xECh
1
1
1
0
1
0
0
0
DXE Drivers initialized
DXE Drivers
Intel® Server System SR1690WB Service Guide
81
Table 10. Diagnostic LED POST Code Decoder
0xEDh
1
1
1
0
1
0
0
1
Transfer control to Boot
Device Selection (BDS)
0xEEh
1
1
1
0
1
1
0
0
Calling Int 19. One beep
unless silent boot is
enabled.
0xEFh
1
1
1
0
1
1
0
1
Unrecoverable boot failure
Pre-EFI Initialization Module (PEIM) / Recovery
82
0x30h
0
0
1
1
0
0
0
0
Crisis recovery has been
initiated because of a user
request
0x31h
0
0
1
1
0
0
0
1
Crisis recovery has been
initiated by software
(corrupt flash)
0x34h
0
0
1
1
0
1
0
0
Loading crisis recovery
capsule
0x35h
0
0
1
1
0
1
0
1
Handing off control to the
crisis recovery capsule
0x36h
0
0
1
1
0
1
1
0
Begin crisis recovery
0x3Eh
0
0
1
1
1
1
1
0
No crisis recovery capsule
detected
0x3Fh
0
0
1
1
1
1
1
1
Crisis recovery capsule
failed integrity check of
capsule descriptors
Intel® Server System SR1690WB Service Guide
Appendix D:
Getting Help
If you encounter an issue with your server system, follow these steps to obtain support:
1. Visit the following Intel support web page:
http://support.intel.com/support/motherboards/server
This web page provides 24x7 support when you need it to get the latest and most
complete technical support information on all Intel Enterprise Server and Storage
Platforms. Information available at the support site includes:
— Latest BIOS, firmware, drivers and utilities
— Product documentation, installation and quick start guides
— Full product specifications, technical advisories and errata
— Compatibility documentation for memory, hardware add-in cards, chassis
support matrix and operating systems
— Server and chassis accessory parts list for ordering upgrades or spare parts
— A searchable knowledge base to search for product information throughout the
support site
2. If you are still unable to obtain a solution to your issue, send an e-mail to Intel’s
technical support center using the online form available at
http://supportmail.intel.com/scripts-emf/welcome.aspx
3. Lastly, you can contact an Intel support representative using one of the support
phone numbers available at http://support.intel.com/support/9089.htm (charges
may apply). Intel customer support suggests filling out the issue report form
available at “Intel® Server Issue Report Form” to better service the issue.
Intel also offers Channel Program members around-the-clock 24x7 technical phone
support on Intel® server boards, server chassis, server RAID controller cards, and
Intel®Server System SR1690WB Service Guide Server Management at http://
www.intel.com/reseller/.
Note: You will need to log in to the Reseller site to obtain the 24x7 number.
Warranty Information
To obtain warranty information, visit the following Intel web site:
http://support.intel.com/support/motherboards/server/sb/CS-010807.htm
83
84
Intel® Server System SR1690WB Service Guide
Appendix E: Regulatory and
Compliance Information
Product Regulatory Compliance
Warning: To ensure regulatory compliance, you must adhere to the assembly instructions in this
guide to ensure and maintain compliance with existing product certifications and
approvals. Use only the described, regulated components specified in this guide. Use of
other products/components will void the UL listing and other regulatory approvals of the
product and will most likely result in noncompliance with product regulations in the
region(s) in which the product is sold.
To help ensure EMC compliance with your local regional rules and regulations, before
computer integration, make sure that the server system, power supply, and other modules
have passed EMC testing using a server board with a microprocessor from the same
family (or higher) and operating at the same (or higher) speed as the microprocessor used
on this server board. The final configuration of your end system product may require
additional EMC compliance testing. For more information, please contact your local Intel
representative.
This is an FCC Class A device. Integration of it into a Class B system does not result in a
Class B device.
This server chassis product, when correctly integrated per this guide, complies with the
following safety and electromagnetic compatibility (EMC) regulations.
Intended Application
This product was evaluated as Information Technology Equipment (ITE), which may be
installed in offices, schools, computer rooms, and similar commercial type locations. The
suitability of this product for other product categories and environments (such as: medical,
industrial, telecommunications, NEBS, residential, alarm systems, test equipment, etc.),
other than an ITE application, may require further evaluation.
Product Safety Compliance
This server chassis product, when correctly integrated per this guide, complies with the
following safety and electromagnetic compatibility (EMC) regulations.
• UL60950 – CSA 60950(USA / Canada)
• EN60950 (Europe)
• IEC60950 (International)
85
• CB Certificate & Report, IEC60950 (report to include all country national
deviations)
• GS Certification (Germany)
•
•
•
•
GOST R 50377-92 - Certification (Russia)
Ukraine Certification (Ukraine)
CE - Low Voltage Directive 73/23/EEE (Europe)
IRAM Certification (Argentina)
Product EMC Compliance - Class A Compliance
Note: Legally the product is required to comply with Class A emission requirements as it is
intended for a commercial type market place. Intel targets 10db margin to Class A Limits
The Intel® Server System SR1690WB was tested and verified to comply with the
following electromagnetic compatibility (EMC) regulations when installed a compatible
Intel® host system. For information on compatible host system(s), refer to Intel's Server
Builder Web site or contact your local Intel representative.
•
•
•
•
•
•
•
•
•
•
FCC /ICES-003 - Emissions (USA/Canada) Verification
•
•
•
•
GOST R 29216-91 Emissions (Russia)
CISPR 22 – Emissions (International)
EN55022 - Emissions (Europe)
EN55024 - Immunity (Europe)
EN61000-3-2 - Harmonics (Europe)
EN61000-3-3 - Voltage Flicker (Europe)
CE – EMC Directive 89/336/EEC (Europe)
VCCI Emissions (Japan)
AS/NZS 3548 Emissions (Australia / New Zealand)
BSMI CNS13438 Emissions (Taiwan)
GOST R 50628-95 Immunity (Russia)
Ukraine Certification (Ukraine)
KCC Certification (EMI) (Korea)
Certifications / Registrations / Declarations
•
•
•
•
86
NRTL ETL Certification (US/Canada)
CE Declaration of Conformity (CENELEC Europe)
FCC/ICES-003 Class A Attestation (USA/Canada)
VCCI Certification (Japan)
Intel® Server System SR1690WB Service Guide
• C-Tick Declaration of Conformity (Australia)
• MED Declaration of Conformity (New Zealand)
• BSMI Certification (Taiwan)
•
•
•
•
•
•
GOST R Certification / Certification (Russia)
KCC Certification (Korea)
IRAM Certification (Argentina)
Ecology Declaration (International)
China RoHS Environmental Friendly Use Period
Packaging & Product Recycling Marks
Product Regulatory Compliance References
The following table references Server Chassis Compliance and markings that may appear
on the product. Markings below are typical markings however, may vary or be different
based on how certification is obtained.
Note: Certifications Emissions requirements are to Class A.
Table 11. Product Regulatory Compliance References
Compliance
Regional
Description
Australia / New
Zealand
Compliance
Reference
Compliance Reference Marking
Example
AS/NZS CISPR22 (Emissions)
N232
Argentina
IRAM Certification (Safety)
Intel® Server System SR1690WB Service Guide
87
Table 11. Product Regulatory Compliance References
Compliance
Regional
Description
Canada / USA
Compliance
Reference
Compliance Reference Marking
Example
CSA 60950 – UL 60950-1 (Safety)
Listing
Industry Canada ICES-003 (Emissions)
CANADA ICES-003 CLASS A
CANADA NMB-003 CLASSE A
FCC CFR 47, Part 15 (Emissions)
CENELEC Europe
This device complies with Part 15 of the
FCC Rules. Operation of this device is
subject to the following two conditions: (1)
This device may not cause harmful
interference, and (2) This device must
accept interference receive, including
interference that may cause undesired
operation.
Low Voltage Directive 2206/95/
EC(Europe – EN60950-1);
EMC Directive 2004/108/EEC EN55022
(Emissions)
EN55024 (Immunity)
EN61000-3-2 (Harmonics)
EN61000-3-3 (Voltage Flicker)
CE Declaration of Conformity
Germany
GS Certification – EN60950-1
International
CB Certification – IEC60950-1
None Required
CISPR 22 / CISPR 24
Japan
88
VCCI Certification
Intel® Server System SR1690WB Service Guide
Table 11. Product Regulatory Compliance References
Compliance
Regional
Description
Korea
Compliance
Reference
Compliance Reference Marking
Example
KCC Certification
인증번호: CPU-SR1690(A)
Russia
GOST-R 50377-92 Certification
GOST R 29216-91 (Emissions)
GOST R 50628-95 (Immunity)
MO04
Ukraine
Ukraine Certification
Taiwan
BSMI CNS13438
None Required
R33025
Intel® Server System SR1690WB Service Guide
89
Electromagnetic Compatibility Notices
FCC Verification Statement (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation
5200 N.E. Elam Young Parkway
Hillsboro, OR 97124-6497
1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit other than the one to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment. The customer is responsible for
ensuring compliance of the modified product.
Only peripherals (computer input/output devices, terminals, printers, etc.) that comply
with FCC Class A or B limits may be attached to this computer product. Operation with
noncompliant peripherals is likely to result in interference to radio and TV reception.
All cables used to connect to peripherals must be shielded and grounded. Operation with
cables, connected to peripherals that are not shielded and grounded may result in
interference to radio and TV reception.
90
Intel® Server System SR1690WB Service Guide
Industry Canada (ICES-003)
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux
appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur:
"Apparelis Numériques", NMB-003 édictee par le Ministre Canadian des
Communications.
English translation of the notice above:
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus set out in the interference-causing equipment standard entitled: "Digital
Apparatus," ICES-003 of the Canadian Department of Communications.
Europe (CE Declaration of Conformity)
This product has been tested in accordance to, and complies with the Low Voltage
Directive (73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked
with the CE Mark to illustrate its compliance.
VCCI (Japan)
Electromagnetic Compatibility Notices (International)
こ
置
用
こ
用
要
の
で
す
と
者
求
装 置 は 、ク ラ ス A 情 報 技 術
す 。こ の 装 置 を 家 庭 環 境 で
る と 電 波 妨 害 を 引 き 起 こ
が あ り ま す 。こ の 場 合 に は
が 適 切 な 対 策 を 講 ず る よ
さ れ る こ と が あ り ま す 。
装
使
す
使
う
English translation of the notice above:
This is a Class A product based on the standard of the Voluntary Control Council For
Interference (VCCI) from Information Technology Equipment. If this is used near a radio
or television receiver in a domestic environment, it may cause radio interference. Install
and use the equipment according to the instruction manual.
Intel® Server System SR1690WB Service Guide
91
BSMI (Taiwan)
The BSMI Certification number and the following warning is located on the product
safety label which is located on the bottom side (pedestal orientation) or side (rack mount
configuration).
The BSMI Certification Marking and EMC warning is located on the outside rear area of
the product.
KCC (Korea)
Following is the KCC certification information for Korea.
인증번호 : CPU-SR1690 (A)
92
Intel® Server System SR1690WB Service Guide
Rack Mount Installation Guidelines
Anchor the equipment rack: The equipment rack must be anchored to an unmovable
support to prevent it from falling over when one or more servers are extended in front of
the rack on slides. You must also consider the weight of any other device installed in the
rack. A crush hazard exists should the rack tilt forward which could cause serious injury.
Temperature: The temperature, in which the server operates when installed in an
equipment rack, must not go below 5 °C (41 °F) or rise above 40 °C (104 °F). Extreme
fluctuations in temperature can cause a variety of problems in your server.
Ventilation: The equipment rack must provide sufficient airflow to the front of the server
to maintain proper cooling. The rack must also include ventilation sufficient to exhaust a
maximum of 1023 BTUs (British Thermal Units) per hour for the server. The rack
selected and the ventilation provided must be suitable to the environment in which the
server will be used.
If AC power supplies are installed:
Mains AC power disconnection: The AC power cord(s) is considered the mains
disconnect for the server and must be readily accessible when installed. If the individual
server power cord(s) will not be readily accessible for disconnection then you are
responsible for installing an AC power disconnect for the entire rack unit. This main
disconnect must be readily accessible, and it must be labeled as controlling power to the
entire rack, not just to the server(s).
Grounding the rack installation: To avoid the potential for an electrical shock hazard, you
must include a third wire safety ground conductor with the rack installation. If the server
power cord is plugged into an AC outlet that is part of the rack, then you must provide
proper grounding for the rack itself. If the server power cord is plugged into a wall AC
outlet, the safety ground conductor in the power cord provides proper grounding only for
the server. You must provide additional, proper grounding for the rack and other devices
installed in it.
Overcurrent protection: The server is designed for an AC line voltage source with up to 20
amperes of overcurrent protection per cord feed. If the power system for the equipment
rack is installed on a branch circuit with more than 20 amperes of protection, you must
provide supplemental protection for the server.
If DC power supplies are installed:
Connection with a DC (Direct Current) source should only be performed by trained
service personnel. The server with DC input is to be installed in a Restricted Access
Location in accordance with articles 110-16, 110-17, and 110-18 of the National Electric
Code, ANSI/NFPA 70. The DC source must be electrically isolated by double or
reinforced insulation from any hazardous AC source.
Intel® Server System SR1690WB Service Guide
93
Main DC power disconnect: You are responsible for installing a properly rated DC power
disconnect for the server system. This mains disconnect must be readily accessible, and it
must be labeled as controlling power to the server. The circuit breaker of a centralized DC
power system may be used as a disconnect device when easily accessible and should be
rated no more than 10 amps.
Grounding the server: To avoid the potential for an electrical shock hazard, you must
reliably connect an earth grounding conductor to the server. The earth grounding
conductor must be a minimum 18AWG connected to the earth ground stud(s) on the rear
of the server. The safety ground conductor should be connected to the chassis stud with a
listed closed two-hole crimp terminal having 5/8 inch pitch. The nuts on the chassis earth
ground studs should be installed with a 10 in/lbs torque. The safety ground conductor
provides proper grounding only for the server. You must provide additional, proper
grounding for the rack and other devices installed in it.
Overcurrent protection: Overcurrent protection circuit breakers must be provided as part
of each host equipment rack and must be incorporated in the field wiring between the DC
source and the server. The branch circuit protection shall be rated minimum 75Vdc, 10 A
maximum per feed pair. If the DC power system for the equipment rack is installed with
more than 10 amperes of protection, you must provide supplemental protection for the
server.
Power Cord Usage Guidelines
Warning: Do not attempt to modify or use an AC power cord set that is not the exact type required.
You must use a power cord set that meets the following criteria:
• Rating: In the U.S. and Canada, cords must be UL (Underwriters Laboratories, Inc.)
Listed/CSA (Canadian Standards Organization) Certified type SJT, 18-3 AWG
(American Wire Gauge). Outside of the U.S. and Canada, cords must be flexible
harmonized (<HAR>) or VDE (Verband Deutscher Electrotechniker, German
Institute of Electrical Engineers) certified cord with 3 x 0.75 mm conductors rated
250 VAC (Volts Alternating Current).
• Connector, wall outlet end: Cords must be terminated in grounding-type male plug
designed for use in your region. The connector must have certification marks
showing certification by an agency acceptable in your region and for U.S. must be
Listed and rated 125% of overall current rating of the server.
• Connector, server end: The connectors that plug into the AC receptacle on the server
must be an approved IEC (International Electrotechnical Commission) 320, sheet
C13, type female connector.
• Cord length and flexibility: Cords must be less than 4.5 meters (14.76 feet) long.
94
Intel® Server System SR1690WB Service Guide
Product Ecology Compliance
Intel has a system in place to restrict the use of banned substances in accordance with
world wide product ecology regulatory requirements. The following is Intel's product
ecology compliance criteria.
Table 12. Product Ecology Compliance
Compliance Regional
Description
California
Compliance Reference
CA. Lithium Perchlorate
insert
California Code of
Regulations, Title 22, Division
4.5; Chapter 33: Best
Management Practices for
Perchlorate Materials.
China
Compliance Reference Marking
Example
Special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/
perchlorate
This notice is required by California Code
of Regulations, Title 22, Division 4.5;
Chapter 33: Best Management Practices
for Perchlorate Materials. This product /
part includes a battery which contains
Perchlorate material.
China RoHS
China RoHS (MII Measure 39)
Product marked with the
Environmental Friendly Usage
Period (EFUP) label of 20yrs,
substance table in Simplified
Chinese either placed with the
product documentation or
separate insert.
China Recycling (GB184552001)
Mark requires to be applied to
be retail product only. Marking
applied to bulk packaging and
single packages. Not applied
to internal packaging such as
plastics, foams, etc.
Intel Internal Specification
All materials, parts and
subassemblies must not
contain restricted materials as
defined in Intel’s
Environmental Product
Content Specification of
Suppliers and Outsourced
Manufacturers – http://
supplier.intel.com/ehs/
environmental.htm
Intel® Server System SR1690WB Service Guide
None Required
95
Table 12. Product Ecology Compliance
Compliance Regional
Description
Europe
Compliance Reference
Compliance Reference Marking
Example
Waste Electrical and
Electronic Equipment
(WEEE) Directive 2002/96/
EC –
Mark applied to system level
products only.
European Directive 2002/95/
EC -
None Required
Restriction of Hazardous
Substances (RoHS)
Threshold limits and banned
substances are noted below.
•
•
Quantity limit of 0.1% by
mass (1000 PPM) for:
Lead, Mercury,
Hexavalent Chromium,
Polybrominated
Biphenyls Diphenyl
Ethers (PBB/PBDE)
Quantity limit of 0.01%
by mass (100 PPM) for:
Cadmium
Intel Internal Specification
All materials, parts and
subassemblies must not
contain restricted materials as
defined in Intel’s
Environmental Product
Content Specification of
Suppliers and Outsourced
Manufacturers – http://
supplier.intel.com/ehs/
environmental.htm
None Required
International
ISO11469 -
>PC/ABS<
Plastic parts weighing >25gm
are intended to be marked
with per ISO11469.
96
Intel® Server System SR1690WB Service Guide
Table 12. Product Ecology Compliance
Compliance Regional
Description
Compliance Reference
Compliance Reference Marking
Example
Recycling Markings –
Fiberboard (FB) and
Cardboard (CB) are marked
with international recycling
marks. Applied to outer bulk
packaging and single
package.
Intel® Server System SR1690WB Service Guide
97
Other Markings
Table 13. Other Markings
Compliance
Description
Stand-by Power
Compliance Reference
Compliance Refernece Markings
Stand-by Power Warnings
Applied to product if stand-by power
switch is used.
Multiple Power
Cords
Multiple Power Cords Warnings
Applied to product if more than one
power cord is used.
English:
This unit has more than one power supply
cord. To reduce the risk of electrical
shock, disconnect (2) two power supply
cords before servicing.
Simplified Chinese:
注意:
本设备包括多条电源系统电缆。
为避免遭受电击,
在进行维修之前应断开两
(2)条电源系统电缆。
Traditional Chinese:
注意:
本設備包括多條電源系統電纜。
為避免遭受電擊,
在進行維修之前應斷開兩
(2)條電源系統電纜。
German:
Dieses Geräte hat mehr als ein
Stromkabel. Um eine Gefahr des
elektrischen Schlages zu verringern
trennen sie beide (2) Stromkabeln bevor
Instandhaltung.
98
Intel® Server System SR1690WB Service Guide
Table 13. Other Markings
Compliance
Description
Compliance Reference
Ground Connection
Ground Connection Warnings
Compliance Refernece Markings
Line1 :
“WARNING:”
Swedish on line2:
“Apparaten skall anslutas till jordat uttag,
när den ansluts till ett nätverk.”
Finnish on line 3:
“Laite on liitettävä
suojamaadoituskoskettimilla varustettuun
pistorasiaan.”
English on line 4:
“Connect only to a properly earth
grounded outlet.”
Country of Origin
Logistic Requirements
Made in China
Applied to products to indicate where
product was made.
Regulated Specified Components
To maintain the UL listing and compliance to other regulatory certifications and/or
declarations, the following regulated components must be used and conditions adhered to.
Interchanging or use of other components will void the UL listing and other product
certifications and approvals.
Updated product information for configurations can be found on the Intel Server Builder
Web site at the following URL: http://channel.intel.com/go/serverbuilder
If you do not have access to Intel's Web address, please contact your local Intel
representative.
• Server Chassis: (base chassis is provided with power supply and fans) - NRTL
listed.
• Server board: you must use an Intel server board - UL recognized.
• Add-in boards: must have a printed wiring board flammability rating of minimum
UL94V-1. Add-in boards containing external power connectors and/or lithium
batteries must be UL recognized or UL listed. Any add-in board containing modem
telecommunication circuitry must be UL listed. In addition, the modem must have
the appropriate telecommunications, safety, and EMC approvals for the region in
which it is sold.
• Peripheral Storage Devices: must be a UL recognized or UL listed accessory and
TUV or VDE licensed. Total server configuration is not to exceed the maximum
loading conditions of the power supply.
Intel® Server System SR1690WB Service Guide
99
End-of-Life / Product Recycling
Product recycling and end-of-life take-back systems and requirements vary by country.
Contact the retailer or distributor of this product for information about product recycling
and / or take-back.
100
Intel® Server System SR1690WB Service Guide
Appendix F:
Warranty
Limited Warranty for Intel® Chassis Subassembly
Products
Intel warrants that the Products (defined herein as the Intel® chassis subassembly and all
of its various components and software delivered with or as part of the Products) to be
delivered hereunder, if properly used and installed, will be free from defects in material
and workmanship and will substantially conform to Intel's publicly available
specifications for a period of three (3) years after the date the Product was purchased from
an Intel authorized distributor. Software of any kind delivered with or as part of products
is expressly provided “as is” unless specifically provided for otherwise in any software
license accompanying the software.
If any Product furnished by Intel which is the subject of this Limited Warranty fails during
the warranty period for reasons covered by this Limited Warranty, Intel, at its option, will:
• REPAIR the Product by means of hardware and/or software; OR
• REPLACE the Product with another Product; OR
• REFUND the then-current value of the Product if Intel is unable to repair or replace
the Product.
If such Product is defective, transportation charges for the return of Product to buyer
within the USA will be paid by Intel. For all other locations, the warranty excludes all
costs of shipping, customs clearance, and other related charges. Intel will have a
reasonable time to make repairs or to replace Product or to refund the then-current value
of the Product.
In no event will Intel be liable for any other costs associated with the replacement or
repair of Product, including labor, installation or other costs incurred by buyer and in
particular, any costs relating to the removal or replacement of any product soldered or
otherwise permanently affixed to any printed circuit board.
This Limited Warranty, and any implied warranties that may exist under state law, apply
only to the original purchaser of the Product.
Extent of Limited Warranty
Intel does not warrant that Products to be delivered hereunder, whether delivered standalone or integrated with other Products, including without limitation semiconductor
components, will be free from design defects or errors known as “errata.” Current
characterized errata are available upon request.
101
This Limited Warranty does not cover damages due to external causes, including accident,
problems with electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair, improper installation, or improper testing.
Warranty Limitations and Exclusions
These warranties replace all other warranties, expressed or implied including, but not
limited to, the implied warranties of merchantability and fitness for a particular purpose.
Intel makes no expressed warranties beyond those stated here. Intel disclaims all other
warranties, expressed or implied including, without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do not allow the
exclusion of implied warranties, so this limitation may not apply.
All expressed and implied warranties are limited in duration to the limited warranty
period. No warranties apply after that period. Some jurisdictions do not allow limitations
on how long an implied warranty lasts, so this limitation may not apply to you.
Limitations of Liability
Intel's responsibility under this, or any other warranty, implied or expressed, is limited to
repair, replacement, or refund, as set forth above. These remedies are the sole and
exclusive remedies for any breach of warranty. Intel is not responsible for direct, special,
incidental, or consequential damages resulting from any breach of warranty under another
legal theory including, but not limited to, lost profits, downtime, goodwill, damage to or
replacement of equipment and property, and any costs of recovering, reprogramming, or
reproducing any program or data stored in or used with a system containing this product.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights
that vary from jurisdiction to jurisdiction.
Any and all disputes arising under or related to this Limited Warranty shall be adjudicated
in the following forums and governed by the following laws: for the United States of
America, Canada, North America, and South America, the forum shall be Santa Clara,
California, USA, and the applicable law shall be that of the State of California, USA; for
the Asia Pacific region, the forum shall be Singapore and the applicable law shall be that
of Singapore; for Europe and the rest of the world, the forum shall be London and the
applicable law shall be that of the United Kingdom.
In the event of any conflict between the English language version and any other translated
version(s) of this Limited Warranty, the English language version shall control.
How to Obtain Warranty Service
To obtain warranty service for this Product, you may contact Intel or your authorized
distributor.
102
Intel® Server System SR1690WB Service Guide
• North America and Latin America To obtain warranty repair for the product, please
go to the following Web site to obtain instructions: http://support.intel.com/support/
motherboards/draform.htm
• In Europe and in Asia Contact your original authorized distributor for warranty
service.
Any replacement Product is warranted under this written warranty and is subject to the
same limitations and exclusions for the remainder of the original warranty period.
Telephone Support
If you cannot find the information you need on Intel's World Wide Web site (http://
www.intel.com/), call your local distributor or an Intel Customer Support representative.
See “Getting Help” for telephone numbers.
Returning a Defective Product
Before returning any product, call your authorized dealer/distribution authority.
Intel® Server System SR1690WB Service Guide
103
104
Intel® Server System SR1690WB Service Guide
Appendix G: Installation/Assembly
Safety Instructions
Important Safety Instructions
Read all caution and safety statements in this document before performing any of the
instructions. See also Intel Server Boards and Server Chassis Safety Information on the
Resource CD and/or at:
http://support.intel.com/support/motherboards/server/sb/cs-010770.htm
English
SAFETY STEPS: Whenever you remove the chassis covers to
access the inside of the system, follow these steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the power button.
3. Unplug all AC power cords from the system or from wall
outlets.
4. Label and disconnect all cables connected to I/O connectors
or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by
wearing an antistatic wrist strap attached to chassis ground
of the system-any unpainted metal surface-when handling
components.
6. Do not operate the system with the chassis covers removed.
A microprocessor and heat sink may be hot if the system has been
running. Also, there may be sharp pins and edges on some board
and chassis parts. Contact should be made with care. Consider
wearing protective gloves.
105
Wichtige Sicherheitshinweise
Lesen Sie zunächst sämtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor
Sie eine der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu
Intel-Serverplatinen und -Servergehäusen auf der Ressourcen-CD oder unter:
http://support.intel.com/support/motherboards/server/sb/cs-010770.htm
SICHERHEISMASSNAHMEN: Immer wenn Sie die
Gehäuseabdeckung abnehmen um an das Systeminnere zu
gelangen, sollten Sie folgende Schritte beachten:
1. Schalten Sie alle an Ihr System angeschlossenen
Peripheriegeräte aus.
2. Schalten Sie das System mit dem Hauptschalter aus.
3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus
der Steckdose.
4. Auf der Rückseite des Systems beschriften und ziehen Sie
alle Anschlußkabel von den I/O Anschlüssen oder Ports ab.
5. Tragen Sie ein geerdetes Antistatik Gelenkband, um
elektrostatische Ladungen (ESD) über blanke Metallstellen
bei der Handhabung der Komponenten zu vermeiden.
6. Schalten Sie das System niemals ohne ordnungsgemäß
montiertes Gehäuse ein.
Der Mikroprozessor und der Kühler sind möglicherweise erhitzt,
wenn das System in Betrieb ist. Außerdem können einige Platinen
und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten
an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie
sollten Schutzhandschuhe tragen.
106
Intel® Server System SR1690WB Service Guide
Consignes de sécurité
Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce
document avant de suivre toute instruction. Consultez Intel Server Boards and Server
Chassis Safety Information sur le CD Resource CD ou bien rendez-vous sur le site:
http://support.intel.com/support/motherboards/server/sb/cs-010770.htm
CONSIGNES DE SÉCURITÉ -Lorsque vous ouvrez le boîtier pour
accéder à l'intérieur du système, suivez les consignes suivantes:
1. Mettez hors tension tous les périphériques connectés au
système.
2. Mettez le système hors tension en mettant l'interrupteur
général en position OFF (bouton-poussoir).
3. Débranchez tous les cordons d'alimentation c.a. du système
et des prises murales.
4. Identifiez et débranchez tous les câbles reliés aux
connecteurs d'E-S ou aux accès derrière le système.
5. Pour prévenir les décharges électrostatiques lorsque vous
touchez aux composants, portez une bande antistatique pour
poignet et reliez-la à la masse du système (toute surface
métallique non peinte du boîtier).
6. Ne faites pas fonctionner le système tandis que le boîtier est
ouvert.
Le microprocesseur et le dissipateur de chaleur peuvent être
chauds si le système a été sous tension. Faites également
attention aux broches aiguës des cartes et aux bords tranchants du
capot. Nous vous recommandons l'usage de gants de protection.
Intel® Server System SR1690WB Service Guide
107
Instrucciones de seguridad importantes
Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar
cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety
Information en el CD Resource y/o en:
http://support.intel.com/support/motherboards/server/sb/cs-010770.htm
INSTRUCCIONES DE SEGURIDAD: Cuando extraiga la tapa del
chasis para acceder al interior del sistema, siga las siguientes
instrucciones:
1. Apague todos los dispositivos periféricos conectados al
sistema.
2. Apague el sistema presionando el interruptor encendido/
apagado.
3. Desconecte todos los cables de alimentación CA del sistema
o de las tomas de corriente alterna.
4. Identifique y desconecte todos los cables enchufados a los
conectores E/S o a los puertos situados en la parte posterior
del sistema.
5. Cuando manipule los componentes, es importante
protegerse contra la descarga electrostática (ESD). Puede
hacerlo si utiliza una muñequera antiestática sujetada a la
toma de tierra del chasis - o a cualquier tipo de superficie de
metal sin pintar.
6. No ponga en marcha el sistema si se han extraído las tapas
del chasis.
Si el sistema ha estado en funcionamiento, el microprocesador y el
disipador de calor pueden estar aún calientes. También conviene
tener en cuenta que en el chasis o en el tablero puede haber
piezas cortantes o punzantes. Por ello, se recomienda precaución
y el uso de guantes protectores.
重要安全指导
在执行任何指令之前,请阅读本文档中的所有注意事项及安全声明。参见 Resource
CD(资源光盘) 和/或http://support.intel.com/support/motherboards/server/sb/cs010770.htm 上的 Intel Server Boards and Server Chassis Safety Information(《Intel
服务器主板与服务器机箱安全信息》)。
108
Intel® Server System SR1690WB Service Guide
Italiano
PASSI DI SICUREZZA: Qualora si rimuovano le coperture del
telaio per accedere all'interno del sistema, seguire i seguenti passi:
1. Spegnere tutti i dispositivi periferici collegati al sistema.
2. Spegnere il sistema, usando il pulsante spento/acceso
dell'interruttore del sistema.
3. Togliere tutte le spine dei cavi del sistema dalle prese
elettriche.
4. Identificare e sconnettere tutti i cavi attaccati ai collegamenti
I/O od alle prese installate sul retro del sistema.
5. Qualora si tocchino i componenti, proteggersi dallo scarico
elettrostatico (SES), portando un cinghia anti-statica da
polso che è attaccata alla presa a terra del telaio del sistema
- qualsiasi superficie non dipinta - .
6. Non far operare il sistema quando il telaio è senza le
coperture.
Se il sistema è stato a lungo in funzione, il microprocessore e il
dissipatore di calore potrebbero essere surriscaldati. Fare
attenzione alla presenza di piedini appuntiti e parti taglienti sulle
schede e sul telaio. È consigliabile l'uso di guanti di protezione.
Intel® Server System SR1690WB Service Guide
109
110
Intel® Server System SR1690WB Service Guide
Appendix H: Safety Information
English
Server Safety Information
This document applies to Intel® Server Boards, Intel® Server Chassis (pedestal and rackmount) and installed peripherals. To reduce the risk of bodily injury, electrical shock, fire,
and equipment damage, read this document and observe all warnings and precautions in
this guide before installing or maintaining your Intel® Server Product.
In the event of a conflict between the information in this document and information
provided with the product or on the website for a particular product, the product
documentation takes precedence.
Your server should be integrated and serviced only by technically qualified persons.
You must adhere to the guidelines in this guide and the assembly instructions in your
server manuals to ensure and maintain compliance with existing product certifications and
approvals. Use only the described, regulated components specified in this guide. Use of
other products / components will void the UL Listing and other regulatory approvals of
the product, and may result in noncompliance with product regulations in the region(s) in
which the product is sold.
Safety Warnings and Cautions
To avoid personal injury or property damage, before you begin installing the product,
read, observe, and adhere to all of the following safety instructions and information. The
following safety symbols may be used throughout the documentation and may be marked
on the product and / or the product packaging.
CAUTION
Indicates the presence of a hazard that may cause minor personal injury or
property damage if the CAUTION is ignored.
WARNING
Indicates the presence of a hazard that may result in serious personal injury
if the WARNING is ignored.
Indicates potential hazard if indicated information is ignored.
Indicates shock hazards that result in serious injury or death if safety
instructions are not followed.
Indicates hot components or surfaces.
111
Indicates do not touch fan blades, may result in injury.
Indicates to unplug all AC power cord(s) to disconnect AC power
Please recycle battery
Intended Application Uses
This product was evaluated as Information Technology Equipment (ITE), which may be
installed in offices, schools, computer rooms, and similar commercial type locations. The
suitability of this product for other product categories and environments (such as medical,
industrial, residential, alarm systems, and test equipment), other than an ITE application,
may require further evaluation.
Site Selection
The system is designed to operate in a typical office environment. Choose a site that is:
• Clean, dry, and free of airborne particles (other than normal room dust).
• Well-ventilated and away from sources of heat including direct sunlight and
radiators.
• Away from sources of vibration or physical shock.
• Isolated from strong electromagnetic fields produced by electrical devices.
• In regions that are susceptible to electrical storms, we recommend you plug your
system into a surge suppressor and disconnect telecommunication lines to your
modem during an electrical storm.
• Provided with a properly grounded wall outlet.
• Provided with sufficient space to access the power supply cord(s), because they
serve as the product's main power disconnect.
Equipment Handling Practices
Reduce the risk of personal injury or equipment damage:
• Conform to local occupational health and safety requirements when moving and
lifting equipment.
• Use mechanical assistance or other suitable assistance when moving and lifting
equipment.
• To reduce the weight for easier handling, remove any easily detachable components.
112
Intel® Server System SR1690WB Service Guide
Deutsch
Sicherheitshinweise für den Server
Das vorliegende Dokument bezieht sich auf Intel® Serverplatinen, Intel® Servergehäuse
(Standfuß und Rack) sowie installierte Peripheriegeräte. Es enthält Warnungen und
Vorsichtsmaßnahmen zur Vermeidung von Gefahren durch Verletzung, Stromschlag,
Feuer und Beschädigungen von Geräten. Lesen Sie diese Dokument daher sorgfältig,
bevor Sie Ihr Intel® Serverprodukt installieren oder warten.
Bei Widersprüchen zwischen den hier vorliegenden Angaben und den Informationen im
Lieferumfang des Produkts oder auf der Website des betreffenden Produkts hat die
Produktdokumentation Vorrang.
Die Integration und Wartung des Servers darf nur durch technisch qualifizierte Personen
erfolgen.
Um die Einhaltung der vorhandenen Zulassungen und Genehmigungen für das Produkt zu
gewährleisten, sind die Richtlinien in diesem Handbuch sowie die Montageanleitungen in
den Serverhandbüchern zu beachten. Verwenden Sie nur die beschriebenen, zugelassenen
Komponenten, die im vorliegenden Handbuch angegeben werden. Die Verwendung
anderer Produkte oder Komponenten führt zum Erlöschen der UL-Zulassung und anderer
Genehmigungen für das Produkt. Dadurch kann das Produkt gegen Produktbestimmungen
verstoßen, die im Verkaufsland gelten.
Sicherheitshinweise und Vorsichtsmaßnahmen
Um Verletzungen und Beschädigungen zu vermeiden, sollten Sie vor dem Beginn der
Produktinstallation die nachfolgend aufgeführten Sicherheitshinweise und -informationen
sorgfältig lesen und befolgen. In dem vorliegenden Handbuch sowie auf dem Produkt und
auf der Verpackung werden folgende Sicherheitssymbole verwendet:
VORSICHT
Weist auf eine Gefahrenquelle hin, die bei Nichtbeachtung des
VORSICHTSHINWEISES zu leichteren Verletzungen bzw.
Sachbeschädigungen führen kann.
WARNUNG
Weist auf eine Gefahrenquelle hin, die bei Nichtbeachtung der WARNUNG
zu ernsten Verletzungen führen kann.
Weist auf potentielle Gefahr bei Nichtbeachtung der angezeigten
Informationen hin.
Weist auf die Gefahr eines Stromschlags hin, der bei Nichtbeachtung der
Sicherheitshinweise zu schweren oder tödlichen Verletzungen führen kann.
Weist auf Verbrennungsgefahr an heißen Bauteilen bzw. Oberflächen hin.
Intel® Server System SR1690WB Service Guide
113
Weist darauf hin, daß das Anfassen des Gebläses zu Verletzungen führen
kann.
Bedeutet, alle Netzkabel abzuziehen und das Gerät von der Netzspannung
zu trennen.
Bereiten Sie bitte Batterie auf
Zielbenutzer der Anwendung
Dieses Produkt wurde in seiner Eigenschaft als IT-Gerät getestet, das in Büros, Schulen,
Computerräumen und ähnlichen öffentlichen Räumlichkeiten installiert werden kann. Die
Eignung dieses Produkts für andere Einsatzbereiche als IT (z. B. Medizin, Industrie,
Alarmsysteme oder Prüfgeräte) kann u. U. weitere Tests erfordern.
Standortauswahl
Das System ist für den Betrieb innerhalb normaler Büroumgebungen geeignet. Wählen
Sie einen Standort, der folgenden Kriterien entspricht:
• Sauber, trocken und frei von Partikeln in der Luft (außer dem normalen Raumstaub).
• Gut belüftet, nicht in der Nähe von Wärmequellen und keiner direkten
Sonnenbestrahlung ausgesetzt.
• Nicht in der Nähe von Vibrations- oder Erschütterungsquellen.
• Abgeschirmt von starken elektromagnetischen Feldern, die durch elektrische Geräte
erzeugt werden.
• In gewittergefährdeten Gebieten sollten Sie das System an einen
Überspannungsschutz anschließen und bei einem Gewitter die
Telekommunikationskabel zum Modem abziehen.
• Eine ordnungsgemäß geerdete Wandsteckdose muß vorhanden sein.
• Ausreichender Freiraum für den Zugang zu den Netzkabeln, da diese die
Hauptvorrichtung zum Trennen des Produkts von der Stromversorgung sind.
Handhabung von Geräten
Beachten Sie zur Vermeidung von Verletzungen oder Beschädigungen an den Geräten die
folgenden Hinweise:
• Halten Sie beim Transportieren und Anheben von Geräten die örtlichen
Gesundheits- und Sicherheitsvorschriften ein.
• Verwenden Sie mechanische oder andere geeignete Hilfsmittel zum Transportieren
oder Anheben von Geräten.
• Entfernen Sie alle Komponenten, die sich leicht abnehmen lassen, um das Gewicht
zu reduzieren und die Handhabung zu erleichtern.
114
Intel® Server System SR1690WB Service Guide
Warnungen zu Netzspannung und Elektrizität
Caution: Durch Betätigen der mit dem Standby-Symbol gekennzeichneten Netztaste wird das
System NICHT vollständig vom Netz getrennt. Es sind weiterhin 5 V aktiv, solange das
System eingesteckt ist. Um das System vollständig vom Strom zu trennen, muß das
Netzkabel aus der Steckdose abgezogen werden. Das System verfügt möglicherweise über
mehrere Netzkabel. Vergewissern Sie sich in diesem Fall, daß alle Netzkabel abgezogen
sind. Wenn Sie Komponenten ein- oder ausbauen möchten, die nicht hot-plug-fähig sind,
stellen Sie sicher, daß zuvor alle Netzkabel abgezogen sind.
Nehmen Sie keine Änderungen am Netzkabel vor, und verwenden Sie kein Kabel, das nicht
genau dem geforderten Typ entspricht. Jedes Netzteil im System muß über ein eigenes
Netzkabel angeschlossen werden.
Einige Netzteile von Intel Servern verwenden Nullleitersicherungen. Vorsicht ist geboten
im Umgang mit Netzteilen, welche Nullleitersicherungen verwenden, um das Risiko eines
elektrischen Schlages zu vermeiden
Das Netzteil in diesem Produkt enthält keine Teile, die vom Benutzer gewartet werden
können. Öffnen Sie das Netzteil nicht. Im Netzteil bestehen gefährliche Spannungen,
Ströme und Energiequellen. Schicken Sie das Gerät für Wartungsarbeiten an den
Hersteller zurück.
Wenn Sie ein hot-plug-fähiges Netzteil austauschen, ziehen Sie dessen Netzkabel ab, bevor
Sie es aus dem Server ausbauen.
Zur Vermeidung von Stromschlägen schalten Sie den Server aus, und trennen Sie vor dem
Öffnen des Geräts das Netzkabel sowie alle an den Server angeschlossene
Telekommunikationssysteme, Netzwerke und Modems.
Hinweis für Netzkabel
Wenn kein Netzkabel mit dem Produkt geliefert wurde, kaufen Sie ein Kabel, das für die
Caution: Prüfen Sie zur Vermeidung von Stromschlag oder Feuergefahr die mit dem Produkt zu
verwendenden Netzkabel wie folgt:
• Nehmen Sie keine Änderungen an einem Netzkabel vor, und benutzen sie es nicht,
wenn es nicht genau in die geerdeten Netzsteckdosen paßt.
• Netzkabel müssen die folgenden Anforderungen erfüllen:
—
Die Nennbelastbarkeit des Netzkabels muß mindestens so hoch sein wie die am
Produkt angegebenen Nennstromaufnahme.
—
Das Netzkabel muß einen zur Netzsteckdose passenden Schutzkontakt besitzen.
• Die Netzkabel sind die Hauptvorrichtung zum Trennen des Geräts vom Stromnetz.
Die Steckdose muß in der Nähe der Anlage angebracht und gut erreichbar sein.
• Netzkabel müssen an eine ordnungsgemäß geerdete Steckdose angeschlossen sein.
Intel® Server System SR1690WB Service Guide
115
Warnhinweise für den Systemzugang
Caution: Um Verletzungen und Beschädigungen zu vermeiden, sollten Sie vor Arbeiten im
Produktinneren folgende Sicherheitsanweisungen beachten:
• Schalten Sie alle am Produkt angeschlossenen Peripheriegeräte aus.
• Schalten Sie das System mit dem Netzschalter aus.
• Trennen Sie das Gerät von der Stromquelle, indem Sie alle Netzkabel vom System
bzw. aus der Steckdose ziehen.
• Ziehen Sie alle Kabel und alle an das System angeschlossenen
Telekommunikationsleitungen ab.
• Bewahren Sie alle Schrauben und anderen Befestigungselemente gut auf, nachdem
Sie die Gehäuseabdeckung entfernt haben. Wenn Sie Ihre Arbeiten im Systeminneren
beendet haben, befestigen Sie die Gehäuseabdeckung mit den Originalschrauben
bzw. -befestigungselementen.
• Führen Sie keine Arbeiten im Netzteil aus. Das Netzteil enthält keine für den
Benutzer wartungsbedürftigen Teile. Schicken Sie das Gerät für Wartungsarbeiten
an den Hersteller zurück.
• Schalten Sie den Server aus, und ziehen Sie alle Netzkabel ab, bevor Sie
Komponenten ein- oder ausbauen, die nicht hot-plug-fähig sind.
• Wenn Sie ein hot-plug-fähiges Netzteil austauschen, ziehen Sie dessen Netzkabel ab,
bevor Sie es aus dem Server ausbauen.
Caution: War Ihr Server in Betrieb, können die installierten Prozessoren und Kühlkörper heiß sein.
Sofern Sie keine Hot-Plug-Komponenten ein- oder ausbauen, warten Sie mit dem
Abnehmen der Abdeckungen, bis das System abgekühlt ist. Gehen Sie beim Aus- oder
Einbauen von Hot-Plug-Komponenten sorgfältig vor, um nicht mit heißen Komponenten
in Berührung zu kommen.
Caution: Berühren Sie nicht die rotierenden Lüfterflügel, um Verletzungen zu vermeiden. Falls Ihr
System mit eine Lüfterabdeckung besitzt, darf es nicht ohne diese Abdeckung betrieben
werden.
Warnhinweise für Racks
Das Geräte-Rack muß auf einer geeigneten, festen Unterlage verankert werden, um ein
Umkippen zu vermeiden, wenn ein Server oder andere Geräte herausgezogen werden.
Bei der Installation des Racks müssen die Anweisungen des Rack-Herstellers beachtet
werden.
Gehen Sie bei der Installation von Geräten im Rack immer von unten nach oben vor, und
bauen Sie das schwerste Gerät an der untersten Position im Rack ein.
Ziehen Sie jeweils immer nur ein Gerät aus dem Rack heraus.
116
Intel® Server System SR1690WB Service Guide
Sie müssen für die gesamte Rack-Einheit einen Netztrennschalter einrichten. Dieser
Netztrennschalter muß leicht zugänglich sein und über eine Kennzeichnung verfügen, die
besagt, daß er die Stromzufuhr zur gesamten Einheit steuert und nicht nur zu den Servern.
Zur Vermeidung von Stromschlaggefahr müssen das Rack selbst und alle darin
eingebauten Geräte ordnungsgemäß geerdet sein.
Elektrostatische Entladungen (ESD)
Caution: Elektrostatische Entladungen können zur Beschädigung von Festplatten, Platinen und
anderen Komponenten führen. Daher sollten Sie alle Arbeiten an einer ESD-Workstation
ausführen. Steht ein solcher Arbeitsplatz nicht zur Verfügung, erzielen Sie einen gewissen
Schutz vor elektrostatischen Entladungen durch Tragen einer Antistatik-Manschette, die
Sie während der Arbeit zur Erdung an einem beliebigen unlackierten Metallteil des
Computergehäuses befestigen.
Gehen Sie bei der Handhabung von Platinen immer mit größter Vorsicht vor. Sie können
äußerst empfindlich gegenüber elektrostatischer Entladung sein. Halten Sie Platinen nur
an den Kanten fest. Legen Sie die Platinen nach dem Auspacken aus der Schutzhülle oder
nach dem Ausbau aus dem Server mit der Bauelementseite nach oben auf eine geerdete,
statisch entladene Unterlage. Verwenden Sie dazu, sofern verfügbar, eine leitfähige
Schaumstoffunterlage, aber nicht die Schutzhülle der Platine. Ziehen Sie die Platine nicht
über eine Fläche.
Andere Gefahren
Batterieaustausch
Caution: Wird die Batterie unsachgemäß ausgetauscht, besteht Explosionsgefahr. Verwenden Sie
als Ersatz nur die vom Gerätehersteller empfohlene Batterie.
Beachten Sie bei der Entsorgung von Batterien die gültigen Bestimmungen.
Versuchen Sie nicht, eine Batterie aufzuladen.
Versuchen Sie nicht, eine Batterie zu öffnen oder sonstwie zu beschädigen.
Kühlung und Luftstrom
Caution: Verlegen Sie Kabel sorgfältig entsprechend der Anleitung, um Störungen des Luftstroms
und Kühlungsprobleme zu vermeiden.
Zur Gewährleistung des ordnungsgemäßen Kühlungs- und Luftstromverhaltens darf das
System nur mit angebrachten Gehäuseabdeckungen betrieben werden. Die
Inbetriebnahme des Systems ohne Abdeckung kann zur Beschädigung von
Systemkomponenten führen. So bringen Sie die Abdeckung wieder an:
• Vergewissern Sie sich zunächst, daß Sie keine Werkzeuge oder Teile im Gehäuse
vergessen haben.
Intel® Server System SR1690WB Service Guide
117
• Prüfen Sie, ob Kabel, Erweiterungskarten sowie weitere Komponenten
ordnungsgemäß angebracht sind.
• Befestigen Sie die Abdeckungen am Gehäuse des Produkts, wie in dessen Anleitung
beschrieben.
Laser-Peripheriegeräte oder -Komponenten
Caution: Beachten Sie zur Vermeidung von Strahlung und Verletzungen die folgenden Hinweise:
• Öffnen Sie keinesfalls das Gehäuse von Laser-Peripheriegeräten oder LaserKomponenten.
• Laser-Peripheriegeräte oder -Komponenten besitzen keine für den Benutzer
wartungsbedürftigen Teile.
• Schicken Sie das Gerät für Wartungsarbeiten an den Hersteller zurück.
Français
Consignes de securite sur le serveur
Ce document s’applique aux cartes serveur Intel®, au châssis de serveur Intel® (sur pieds
et sur rack) et aux périphériques installés. Pour réduire les risques de dommages
corporels, d’électrocution, d’incendie et de dommages matériels, lisez ce document et
respectez tous les avertissements et précautions mentionnés dans ce guide avant
d’installer ou de mettre à jour votre produit serveur Intel®.
En cas de conflit entre les informations fournies dans ce document et celles livrées avec le
produit ou publiées sur le site Web pour un produit particulier, la documentation du
produit prime.
Votre serveur doit être intégré et entretenu uniquement par des techniciens qualifiés.
Vous devez suivre les informations de ce guide et les instructions d’assemblage des
manuels de serveur pour vérifier et maintenir la conformité avec les certifications et
approbations de produit existantes. Utilisez uniquement les composants décrits et
réglementés spécifiés dans ce guide. L’utilisation d’autres produits/composants annulera
la liste UL et les autres approbations réglementaires du produit, et le produit peut ne pas
être conforme aux autres lois et réglementations locales applicables au produit.
Séurité: avertissements et mises en garde
Pour éviter de vous blesser ou d’endommager votre équipement, lisez et respectez toutes
les informations et consignes de sécurité avant de commencer l’installation du produit.
Les symboles de sécurité suivants peuvent être utilisés tout au long de cette
documentation et peuvent figurer sur le produit ou sur son emballage.
118
Intel® Server System SR1690WB Service Guide
ATTENTION
Indique la présence d’un risque pouvant entraîner des blessures
physiques mineures ou endommager légèrement le matériel si la mise en
garde n’est pas prise en compte.
AVERTISSEMEN
T
Indique la présence d’un risque pouvant entraîner des blessures
corporelles graves si l’avertissement n’est pas pris en compte.
Indique un risque potentiel si les informations signalées ne sont pas prises
en compte.
Indique des risques d’électrocution pouvant entraîner des blessures
corporelles graves ou mortelles si les consignes de sécurité ne sont pas
respectées.
Signale des composants ou des surfaces soumis à des températures
élevées.
Indique de ne pas toucher aux pales de ventilateur, car cela peut entraîner
des blessures.
Indique de débrancher tous les cordons d’alimentation secteur pour
déconnecter l’alimentation.
Veuillez réutiliser la batterie
Domaines d’utilisation prévus
Ce produit a été testé comme équipement informatique (ITE) et peut être installé dans des
bureaux, des écoles, des salles informatiques et des endroits commerciaux similaires.
L’utilisation du présent produit dans des catégories et environnements de produits et
domaines d’application (par exemple, le domaine médical, industriel, résidentiel, les
systèmes d’alarme et les appareils de contrôle) autres qu’ITE doit faire l’objet
d’évaluations supplémentaires.
Sélection d’un emplacement
Le système est conçu pour fonctionner dans un environnement standard de bureau.
Choisissez un emplacement respectant les conditions suivantes :
• Propre, sec et exempt de particules en suspension (autres que la poussière normale
d’une pièce).
• Bien ventilé et à l’écart des sources de chaleur telles que la lumière directe du soleil
et les radiateurs.
• À l’écart des sources de vibration ou des chocs physiques.
• Isolé des champs électromagnétiques importants produits par des appareils
électriques.
Intel® Server System SR1690WB Service Guide
119
• Dans les régions sujettes aux orages magnétiques, nous vous recommandons de
brancher votre système à un suppresseur de surtension et de déconnecter les lignes
de télécommunication de votre modem pendant les orages.
• Équipé d’une prise murale reliée à la terre.
• Équipé d’un espace suffisant pour accéder aux cordons d’alimentation secteur, car
ils servent de disjoncteur principal d’alimentation du produit.
Pratiques de manipulation de l’équipement
Réduisez le risque de dommages personnels ou matériels :
• Conformez-vous aux exigences de médecine du travail et de sécurité lorsque vous
déplacez et soulevez le matériel.
• Utilisez l’assistance mécanique ou toute autre assistance appropriée lorsque vous
déplacez et soulevez le matériel.
• Pour réduire le poids en vue de faciliter la manipulation, retirez tout composant
amovible.
Alimentation et avertissements en matiére d’électricité
Attention:Le bouton d’alimentation, indiqué par le symbole de mise en veille, NE COUPE PAS
complètement l’alimentation secteur du système car le courant de veille 5 V reste actif
lorsque le système est sous tension. Pour couper l’alimentation du système, vous devez
débrancher le cordon d’alimentation secteur de la prise murale. Votre système peut
utiliser plusieurs cordons d’alimentation secteur. Assurez-vous que tous les cordons
d’alimentation sont débranchés. Vous devez les débrancher avant d’ouvrir le châssis,
d’ajouter ou de supprimer un composant non connectable à chaud.
Les alimentations de certains serveurs Intel sont munies de doubles fusibles pôle/neutre:
veuillez observer les précautions d'usage afin d'éviter tout risque d'eléctrocution.
N’essayez pas de modifier ou d’utiliser un cordon d’alimentation secteur s’il ne s’agit pas
du type exact requis. Un cordon secteur est requis pour chaque alimentation système.
Le bloc d’alimentation de ce produit ne contient aucun composant réparable par
l’utilisateur. N’ouvrez pas le bloc d’alimentation. L’intérieur de celui-ci est soumis à des
120
Intel® Server System SR1690WB Service Guide
niveaux dangereux de tension, de courant et d’énergie. Renvoyez-le au fabricant en cas de
problème.
Lorsque vous remplacez un bloc d’alimentation à chaud, débranchez le cordon du bloc
d’alimentation en cours de remplacement avant de le retirer du serveur.
Pour éviter tout risque d’électrocution, mettez le système hors tension et débranchez les
cordons d’alimentation ainsi que les systèmes de télécommunication, réseaux et modems
reliés au système avant d’ouvrir ce dernier.
Avertissements sur le cordon d’alimentation
Si aucun cordon d’alimentation secteur n’a été fourni avec votre produit, vous devez vous
en procurer un qui soit approuvé pour une utilisation dans votre pays.
Attention:Pour éviter tout risque d’électrocution ou d’incendie, vérifiez les cordons d’alimentation
qui seront utilisés avec le produit comme suit :
• N’essayez pas d’utiliser ou de modifier les cordons d’alimentation en CA s’ils ne
correspondent pas exactement au type requis pour les prises électriques reliées à la
terre.
• Les cordons d’alimentation doivent répondre aux critères suivants :
—
Le cordon d’alimentation doit supporter une intensité supérieure à celle
indiquée sur le produit.
—
Le cordon d’alimentation doit posséder une broche ou un contact de mise à la
terre approprié à la prise électrique.
• Les cordons d’alimentation électrique représentent le principal dispositif de
déconnexion raccordé à l’alimentation secteur. Les prises de courant doivent se
trouver à proximité de l’équipement et être facilement accessibles pour une
déconnexion.
• Les cordons d’alimentation doivent être branchés sur des prises électriques
correctement reliées à la terre.
Avertissements sur l’accés au systéme
Attention:Pour éviter de vous blesser ou d’endommager votre équipement, les consignes de sécurité
suivantes s’appliquent chaque fois que vous accédez à l’intérieur du produit :
• Mettez hors tension tous les périphériques connectés à ce produit.
• Éteignez le système en appuyant sur le bouton d’alimentation.
• Déconnectez l’alimentation secteur en débranchant tous les cordons d’alimentation
secteur du système ou de la prise murale.
• Déconnectez l’ensemble des câbles et lignes de télécommunication qui sont
connectés au système.
Intel® Server System SR1690WB Service Guide
121
• Mettez toutes les vis ou autres attaches de côté lorsque vous retirez les panneaux
d’accès. Une fois que vous avez terminé d’accéder à l’intérieur du produit, refixez le
panneau d’accès avec les vis ou attaches d’origine.
• N’essayez pas d’accéder à l’intérieur du bloc d’alimentation. Il ne contient aucune
pièce réparable. Renvoyez-le au fabricant en cas de problème.
• Mettez le serveur hors tension et débranchez tous les cordons d’alimentation avant
d’ajouter ou de remplacer tout composant non connectable à chaud.
• Lorsque vous remplacez le bloc d’alimentation à chaud, débranchez le cordon du
bloc d’alimentation en cours de remplacement avant de retirer le bloc du serveur.
Attention:Si le serveur a été utilisé, les processeurs et dissipateurs de chaleur installés peuvent être
chauds. À moins que vous n’ajoutiez ou ne retiriez un composant connectable à chaud,
laissez le système refroidir avant d’ouvrir les panneaux. Pour éviter tout risque d’entrer
en contact avec un composant chaud lors d’une installation à chaud, prenez toutes les
précautions nécessaires lorsque vous retirez ou installez des composants connectables à
chaud.
Attention:Pour éviter de vous blesser, ne touchez pas les pales de ventilateur en mouvement. Si
votre système est fourni avec une protection sur le ventilateur, ne mettez pas le système en
route sans la protection en place.
Avertissements sur le montage en rack
Le rack doit être fixé à un support inamovible pour éviter qu’il ne bascule lors de
l’extension d’un serveur ou d’un élément de l’équipement. Le rack doit être installé
conformément aux instructions du fabricant.
Installez les équipements dans le rack en partant du bas, en plaçant le plus lourd en bas du
rack.
N’étendez qu’un seul élément de l’équipement à partir du rack à la fois.
Vous êtes responsable de l’installation d’un disjoncteur principal d’alimentation pour la
totalité du rack. Ce disjoncteur principal doit être rapidement accessible et doit être
étiqueté comme contrôlant toute l’unité, et pas uniquement le ou les serveurs.
Pour éviter tout risque d’électrocution, le rack et chaque élément de l’équipement installé
dans le rack doivent être correctement reliés à la terre.
122
Intel® Server System SR1690WB Service Guide
Décharges électrostatiques (ESD)
Attention:Les décharges électrostatiques (ESD) peuvent endommager les lecteurs de disque dur, les
cartes et d’autres pièces. Il est fortement conseillé d’effectuer l’ensemble des procédures
décrites à un poste de travail protégé contre les ESD. Au cas où aucun poste de ce type ne
serait disponible, protégez-vous contre les ESD en portant un bracelet antistatique relié à
la masse du châssis (n’importe quelle surface métallique non peinte) de votre serveur
lorsque que vous manipulez les pièces.
Manipulez toujours les cartes avec précaution. Elles peuvent être extrêmement sensibles
aux ESD. Ne tenez les cartes que par leurs bords. Après avoir retiré une carte de son
emballage de protection ou du serveur, placez-la sur une surface reliée à la terre, exempte
de charge statique, composants orientés vers le haut. Utilisez si possible un tapis de
mousse conducteur, mais pas l’emballage de la carte. Veillez à ce que la carte ne glisse
sur aucune surface.
Autres risques
Remplacement de la pile
Attention:Il existe un risque d’explosion si la pile n’est pas correctement remplacée. Lors du
remplacement de la pile, utilisez uniquement celle recommandée par le fabricant du
matériel.
Mettez la pile au rebut en vous conformant aux réglementations locales.
N’essayez pas de recharger une pile.
N’essayez pas de démonter, de percer ou d’endommager la pile d’une quelconque façon.
Refroidissement et ventilation
Attention:Routez les câbles avec précaution comme indiqué pour minimiser les blocages de
circulation d’air et les problèmes de refroidissement.
Afin de permettre une ventilation et un refroidissement corrects, ne mettez le système en
marche que lorsque les panneaux du châssis sont en place. L’utilisation du système sans
les panneaux peut endommager les composants système. Pour installer les panneaux :
• Vérifiez tout d’abord que vous n’avez pas oublié d’outils ou de composants détachés
à l’intérieur du système.
• Vérifiez que les câbles, les cartes d’extension et les autres composants sont
correctement installés.
• Fixez les panneaux au châssis en suivant les instructions du produit.
Intel® Server System SR1690WB Service Guide
123
Périphériques laser
Attention:Pour éviter tout risque d’exposition aux rayonnements et/ou de dommage personnel:
• N’ouvrez pas l’enceinte d’un périphérique laser.
• Les périphériques laser ne sont pas réparables par l’utilisateur.
• Retournez-les au fabricant en cas de problème.
Español
Información de seguridad del servidor
Este documento se aplica a las tarjetas de servidor de Intel®, las carcasas de servidor de
Intel® (montaje en bastidor y en pedestal) y los dispositivos periféricos. Para reducir el
riesgo de daños corporales, descargas eléctricas, fuego y en el equipo, lea este documento
y preste atención a todos las advertencias y precauciones de esta guía antes de instalar o
mantener el producto de servidor de Intel®.
En el caso de que haya diferencias entre la información para un producto en particular
contenida en este documento y la información proporcionada con dicho producto o en el
sitio Web, la documentación del producto es la que prevalece.
Sólo personal técnico cualificado debe montar y prestar los servicios para el servidor.
Debe ceñirse a las directrices de esta guía y a las instrucciones de montaje de los manuales
del servidor para asegurar y mantener el cumplimiento con las certificaciones y
homologaciones existentes de los productos. Utilice sólo los componentes descritos y
homologados que se especifican en esta guía. El uso de otros productos o componentes
anulará la homologación UL y otras certificaciones oficiales del producto, pudiendo dejar
de ser compatible con las normativas locales de los países en los que se comercializa.
Advertencias y precauciones sobre seguridad
Para reducir la posibilidad de que se produzcan lesiones personales o daños en la
propiedad, antes de empezar a instalar el producto, lea, observe y cumpla toda la
información e instrucciones de seguridad siguientes. Puede que se utilicen los siguientes
símbolos de seguridad en la documentación y es posible que aparezcan en el producto o en
su embalaje.
124
PRECAUCIÓN
Indica la existencia de un riesgo que podría causar lesiones personales o
daños en la propiedad leves si no se tiene en cuenta la PRECAUCIÓN.
ADVERTENCIA
Indica la existencia de un riesgo que podría causar lesiones personales
graves si no se tiene en cuenta la ADVERTENCIA.
Intel® Server System SR1690WB Service Guide
Indica un riesgo potencial si no se tiene en cuenta la información indicada.
Indica riesgo de descargas eléctricas que podrían causar lesiones graves o
la muerte si no se siguen las instrucciones de seguridad.
Indica componentes o superficies calientes.
Indica que no se deben tocar las aspas de los ventiladores, ya que de lo
contrario se podrían producir lesiones.
Indica que es necesario desenchufar los cables de alimentación de CA para
desconectar la alimentación de CA
Recicle por favor la batería
Aplicaciones y usos previstos
Este producto ha sido evaluado como equipo de tecnología informática (ITE) que puede
instalarse en oficinas, escuelas, salas de equipos informáticos o lugares de ámbito
comercial similares. Es posible que sea necesario llevar a cabo una evaluación adicional
para comprobar si este producto es apropiado para otras categorías de productos y
entornos además de las aplicaciones informáticas (por ejemplo, soluciones médicas,
industriales, residenciales, sistemas de alarma y equipos de pruebas).
Seleccién de la ubicación
El sistema se ha diseñado para funcionar en un entorno normal de oficinas. Seleccione una
ubicación que esté:
• Limpia, seca y libre de macropartículas en suspensión en el aire (que no sean el
polvo habitual de la habitación).
• Bien ventilada y alejada de fuentes de calor, incluida la luz solar directa y los
radiadores.
• Alejada de fuentes de vibración o de golpes físicos.
• Aislada de campos electromagnéticos producidos por dispositivos eléctricos.
• En zonas propensas a tormentas eléctricas, se recomienda que conecte el servidor a
un supresor de sobretensiones y desconecte las líneas de telecomunicaciones al
módem durante una tormenta eléctrica.
• Provista de una toma de corriente alterna correctamente conectada a tierra.
• Provista de espacio suficiente para acceder a los cables de la fuente de alimentación
ya que constituyen la desconexión principal de la alimentación.
Intel® Server System SR1690WB Service Guide
125
Manipulacién del equipo
Reduzca el riesgo de daños personales o en el equipo:
• Respete los requisitos de sanidad y seguridad laborales de su país cuando traslade y
levante el equipo.
• Utilice medios mecánicos u otros que sean adecuados al trasladar o levantar el
equipo.
• Para que el peso sea menor para manipularlo con más facilidad, extraiga los
componentes que sean de fácil extracción.
Advertencias de alimentacién y eléctricas
Precaución: El botón de encendido, indicado con la marca del modo de reposo o stand-by, NO
DESCONECTA completamente la alimentación de CA del sistema, ya que el modo de
reposo de 5 V sigue activo mientras el sistema está enchufado. Para desconectar el
sistema debe desenchufar el cable de alimentación de CA de la toma de la pared. Puede
usar más de un cable de alimentación de CA con el sistema. Asegúrese de que todos los
cables de alimentación de CA están desenchufados. Asegúrese de que los cables de
alimentación de CA estén desenchufado antes de abrir la carcasa, agregar o extraer
cualquier componente que no es de conexión en funcionamiento.
Algunas fuentes de alimentación de electricidad de los servidores de Intel utilizan el polo
neutral del fuselaje. Para evitar riesgos de choques electricos use precauciónes al
trabajar con las fuentes de alimentación que utilizan el polo neutral de fuselaje.
No intente modificar ni utilizar un cable de alimentación de CA si no es del tipo exacto
requerido. Se necesita un cable de CA para cada fuente de alimentación del sistema.
La fuente de alimentación de este producto no contiene piezas que puedan ser reparadas
por el usuario. No abra la fuente de alimentación. Dentro de la fuente de alimentación
puede haber niveles de tensión, corriente y energía peligrosos. Devuélvala al fabricante
para repararla.
Al reemplazar una fuente de alimentación de conexión en funcionamiento, desenchufe el
cable de alimentación de la fuente de alimentación que va a reemplazar antes de extraerla
del servidor.
Para evitar el riesgo de descargas eléctricas, antes de abrir el servidor, apáguelo,
desconecte el cable de alimentación, los sistemas de telecomunicaciones, las redes y los
módems conectados al mismo.
Advertencias sobre el cable de alimentación
Si no se ha proporcionado con el producto ningún cable de alimentación de CA, adquiera
alguno cuyo uso esté aprobado en su país.
126
Intel® Server System SR1690WB Service Guide
Precaución: Para evitar descargas eléctricas o fuego, revise los cables de alimentación que usará con
el producto tal y como se describe a continuación:
• No intente modificar ni utilizar los cables de alimentación de CA si no son
exactamente del modelo especificado para ajustarse a las tomas de corriente
conectadas a tierra.
• Los cables de alimentación deben reunir los siguientes requisitos:
—
El cable de alimentación debe disponer de una capacidad nominal de corriente
eléctrica mayor que la capacidad especificada en el producto.
—
El cable de alimentación debe disponer de una patilla o contacto de conexión a
tierra que sea apto para la toma de corriente.
• Los cables de la fuente de alimentación son los dispositivos de desconexión
principales a la corriente alterna. El enchufe o enchufes de zócalo deben
encontrarse cerca del equipo y el acceso a ellos debe poderse efectuar de forma
inmediata con el fin de desconectarlos.
• Los cables de la fuente de alimentación deben estar conectados a los enchufes con
una toma de tierra adecuada.
Advertencias el acceso al sistema
Precaución: Para evitar lesiones personales o daños en la propiedad, se aplican las siguientes
instrucciones de seguridad siempre que se acceda al interior del producto:
• Apague todos los dispositivos periféricos conectados a este producto.
• Pulse el botón de alimentación para apagar el sistema.
• Desconecte la alimentación de CA desenchufando los cables de alimentación de CA
del sistema o de la toma de corriente alterna.
• Desconecte todos los cables y líneas de telecomunicación que estén conectados al
sistema.
• Guarde todos los tornillos o elementos de fijación cuando retire las cubiertas de
acceso. Cuando termine de operar en el interior del producto, vuelva a colocar los
tornillos o los elementos de fijación originales de la cubierta de acceso.
• No acceda al interior de la fuente de alimentación. No hay elementos en la fuente de
alimentación que usted pueda reparar y utilizar. Devuélvala al fabricante para
repararla.
• Apague el servidor y desconecte todos los cables de alimentación antes de agregar
o reemplazar cualquier componente que no es de conexión en funcionamiento.
Intel® Server System SR1690WB Service Guide
127
• Al reemplazar una fuente de alimentación de conexión en funcionamiento,
desenchufe el cable de alimentación de la fuente de alimentación que va a
reemplazar antes de extraerla del servidor.
Precaución: Si el servidor se ha estado ejecutando, los procesadores y disipadores de calor estarán
recalentados. A no ser que esté instalando o extrayendo un componente de conexión en
funcionamiento, deje que el sistema se enfríe antes de abrir las cubiertas. Para que no
llegue a tocar los componentes que estén calientes cuando esté realizando una instalación
de conexión en funcionamiento, tenga cuidado al extraer o instalar los componentes de
conexión en funcionamiento.
Precaución: Para evitar posibles daños, no toque las aspas en movimiento de los ventiladores. Si el
sistema se le ha suministrado con una protección para el ventilador, asegúrese de que
cuando esté funcionando el sistema la protección esté en su sitio.
Advertencias sobre el montaje en bastidor
El bastidor del equipo se debe sujetar con un soporte fijo para evitar que se caiga cuando
se extraiga un servidor o una pieza del mismo. El bastidor del equipo debe instalarse
siguiendo las instrucciones del fabricante del bastidor.
Instale el equipo en el bastidor comenzando desde la parte de abajo, con el equipo más
pesado en la parte inferior del bastidor.
Extraiga las piezas del equipo del bastidor de una a una.
El usuario es el responsable de la instalación de un dispositivo de desconexión de la
alimentación principal para toda la unidad del bastidor. El acceso a este dispositivo de
desconexión deberá ser de fácil acceso y deberán incluirse indicaciones que lo
identifiquen como el control de alimentación eléctrica de toda la unidad, no sólo de los
servidores.
Para evitar el riesgo de descargas eléctricas, deberá instalar una conexión a tierra
apropiada para el bastidor y para cada pieza del equipo instalada en el mismo.
128
Intel® Server System SR1690WB Service Guide
Descarga electrostática (ESD)
Precaución: Las descargas electrostáticas pueden dañar las unidades de disco, las tarjetas y otros
componentes. Recomendamos que realice todos los procedimientos en una estación de
trabajo protegida contra descargas electrostáticas. En caso de que no haya una
disponible, protéjase de alguna forma contras las descargas llevando un brazalete
antiestático conectado a la toma de tierra de la carcasa (cualquier superficie de metal
que no esté pintada) del servidor cuando manipule las piezas.
Manipule siempre las tarjetas con el máximo cuidado. Pueden ser sumamente sensibles a
las descargas electrostáticas. Sujételas sólo por los bordes. Una vez extraída la tarjeta de
su envoltorio de protección o del servidor, colóquela con el lado de los componentes
hacia arriba sobre una superficie con toma de tierra y sin carga estática. Utilice una
almohadilla de espuma conductora si dispone de ella, pero nunca el envoltorio de la
tarjeta. No deslice la tarjeta sobre ninguna superficie.
Otros riesgos
Sustitución de la batería
Precaución: Existe el peligro de explosión si la batería no se reemplaza correctamente. Al reemplazar
la batería, utilice sólo la batería recomendada por el fabricante del equipo.
Deseche las baterías respetando la normativa local.
No intente recargar la batería.
No intente desmontar, pinchar o causar cualquier otro desperfecto a una batería.
Intel® Server System SR1690WB Service Guide
129
Enfriamiento y circulación de aire
Precaución: El tendido de los cables debe realizarse cuidadosamente tal y como se le indica para
reducir al mínimo los problemas de obstrucción de la ventilación y de refrigeración.
Para conseguir una refrigeración y corriente de aire adecuadas, compruebe que cuando
sistema esté funcionando, las cubiertas de la carcasa están instaladas. Si utiliza el sistema
sin las cubiertas, podría dañar sus componentes. Para instalar las cubiertas:
• Compruebe primero que no ha dejado herramientas o piezas sueltas dentro del
sistema.
• Compruebe que los cables, tarjetas adicionales y otros componentes están
instalados correctamente.
• Sujete las cubiertas a la carcasa siguiendo las instrucciones del producto.
Periféricos o dispositivos láser
Precaución Para evitar el riesgo de la exposición a radiaciones o de daños personales:
• No abra la caja de ningún periférico o dispositivo láser
• Los periféricos o dispositivos láser no pueden ser reparados por el usuario
• Haga que el fabricante los repare
130
Intel® Server System SR1690WB Service Guide
简体中文
服务器安全信息
本文档适用于 Intel® 服务器主板、Intel®
服务器机箱(基座和机架固定件)和已安装的外设。为减少人身伤害、电击、火灾
以及设备毁坏的危险,请在安装或维护 Intel®
服务器产品之前阅读本文档并遵循本指南中的所有警告和预防措施。
如果本文档中的信息与特定产品的随附信息或 Web
站点信息之间存在不一致,请以产品文档为准。
服务器须由合格的技术人员进行集成和维护。
必须遵守本指南的规定和服务器手册的装配指导,以确保符合现有的产品认证和审
批。仅使用本指南中描述和规定的指定组件。使用其他产品 / 组件将使产品的 UL
认证和其他管理审批无效,并可能导致产品不符合销售地的产品法规。
安全警告与注意事项
为避免人身伤害与财产损失,安装本产品之前,请阅读以下所有安全指导和信息。
下面所列的安全符号可能在整个文档中使用并可能标注于产品和 /
或产品包装之上。
注意
表示如果无视此“? ? ? 项”? ? ? ? ? ? ? 轻微人身伤害或财产损失的危险。
警告
表示如果无视此“? ? ”? ? ? ? ? ? ? 严重人身伤害的危险。
表示如果无视所示信息,即存在潜在的危险。
表示如果不遵守安全指导,存在可导致严重伤害或死亡的电击危险。
表示灼热组件或表面。
表示请勿触摸风机叶片,否则可能致伤。
表示拔下所有交流电线,断开交流电源
Intel® Server System SR1690WB Service Guide
131
预期应用使用
根据评估,本产品为信息技术设备
(ITE),可安装在办公室、学校、计算机房和类似的商业场所。本产品对于非 ITE
应用的其他产品种类和环境(如医疗、工业、住宅、报警系统和测试设备)的适用
性尚有待进一步的评估。
场地选择
本系统专为在典型办公环境运行而设计。请选择符合以下条件的地点:
•
•
•
•
•
•
•
清洁、干燥,无气载微粒(而非一般的室内尘埃)。
通风良好,远离热源(包括直接日晒和散热器)。
远离振动源或物理震动。
与电气设备产生的强大电磁场隔离。
在易受闪电袭击的地区,我们建议将系统插入电涌抑制器并在闪电期间断开通信
线路与调制解调器之间的连接。
提供正确接地的墙壁插座。
提供足够的空间,以便拿取电源供应线,因为这是本产品的主要电源断开器。
设备操作规范
减少人身伤害或设备受损的危险:
•
•
•
移举设备时遵守当地的职业健康与安全要求。
借助机械手段或其他合适的手段移举设备。
拆除一切易分离组件,以降低重量并方便操作。
电源与电气警告
注意事项
电源按钮(如待机电源标记所示)并不能完全关闭系统的交流电源,只要系统已接
通电源,就存在 5V
待机电源。要从系统切断电源,须从墙壁电源插座中拔下交流电线。您的系统可能
不止使用一根交流电线。请确保所有的交流电线都已拔下。打开机箱或增加或去除
任何热插拔组件之前,确保交流电线已拔下。
若非所需的确切类型,请勿尝试修改或使用交流电线。系统的每个电源供应设备都
需要一根单独的交流电线。
本产品的电源供应设备包含非用户维修部件。请勿打开电源供应设备。电源供应设
备包含非常危险的电压级、电流级和能量级。请与生产商联系维修事宜。
替换热插拔电源供应设备时,请先拔下需替换的电源供应设备上的电源线,再将其
从服务器上移除。
132
Intel® Server System SR1690WB Service Guide
为避免电击,请在打开服务器之前,关闭服务器并断开服务器上连接的电源线、电
信系统、网络和调制解调器。
电源线警告
如果产品未提供交流电线,请购买一根您所在国家批准使用的交流电线。
注意事项
为避免电击或火灾危险,请按如下所述对产品所用的电源线进行检查:
•
•
•
•
若非所需的符合接地插座的确切类型,请勿尝试修改或使用交流电线
电源线须符合以下标准:
⎯ 电源线的电气额定值须大于产品上标注的电流额定值。
⎯ 电源线须拥有适合插座的安全接地插头或触点。
电源线为交流电源的主要断开设备。插座须靠近设备并可随时断开。
电源线须插入所提供的拥有合适接地的插座。
系统使用警告
注意事项
为避免人身伤害或财产损失,无论何时检查产品内部,以下安全指导都适用:
•
•
•
•
•
•
•
•
关闭所有与本产品相连的外设。
按下电源按钮至关闭状态,关闭系统。
从系统或墙壁插座上拔下所有交流电线,断开交流电源。
断开与系统相连的所有线缆和通信线路。
卸除舱口盖时,保留所有螺钉及其他紧固件。完成产品内部检查之后,请
用螺钉或紧固件重新固定舱口盖。
请勿打开电源供应设备。电源供应设备内没有可维修部件。请与生产商联系
维修事宜.
增加或替换任何非热插拔组件之前,请关闭服务器电源并断开所有电源线
。
替换热插拔电源供应设备时,请先拔下需替换的电源供应设备上的电源线
,然后再从服务器上移除电源供应设备。
注意事项
如果服务器一直在运行,任何已安装的处理器和吸热设备都可能很热。除非要增加
或移除热插拔组件,否则请待系统冷却后再开盖。为避免在热插拔组件安装过程中
接触灼热组件,移除或安装热插拔组件时务须小心。
Intel® Server System SR1690WB Service Guide
133
注意事项
为避免受伤,请勿触摸运转的风机叶片。如果系统的风机上配有防护装置,请勿卸
下风机防护装置运行系统。
机架固定件警告
设备的机架须固定在稳固的支座上,以防从中安装服务器或设备时倒塌。须按照机
架生产商提供的安装说明进行安装。
从下往上将设备安装在机架上,最重的设备安装在机架的最底层。
一次只从机架上安装一件设备。
您须负责安装整个机架装置的主要电源断开设备。此主要断开设备须随时可用,且
须标明为控制整个装置(而不仅限于服务器)的电源。
为避免潜在的电击危险,须对机架及其上所安装的每一件设备实行正确的安全接地
。
静电放电 (ESD)
注意事项
ESD 会损坏磁盘驱动器、主板及其他部件。我们建议您执行 ESD
工作站的所有步骤。如果没有 ESD
工作站,则采取一些静电放电保护措施,操作部件时,戴上与服务器上的机箱接地
或任何未喷漆金属表面连接的防静电腕带。
操作主板时始终保持小心。它们可能对 ESD
非常敏感。拿持主板时只接触边缘。从保护包装中或从服务器上取出主板后,请将
主板组件侧面朝上放置在无静电的接地表面上。请使用导电泡沫垫(若有),不要
使用主板包装。请勿将主板在任何表面上滑动。
134
Intel® Server System SR1690WB Service Guide
其他危险
替换电池
注意事项
不正确替换电池可能导致爆炸危险。替换电池时,请只使用设备生产商推荐使用的
电池。
请按当地法规处置电池。
请勿对电池充电。
请勿拆卸、刺穿或以其他方式损坏电池。
冷却和气流
注意事项
按照说明小心布置线缆,尽量减少气流阻塞和冷却问题。
为保证适当的冷却和气流,运行系统时请确保机箱盖已安装。未安装机箱盖即运行
系统可能导致系统部件受损。安装机箱盖的步骤如下:
•
•
•
首先检查并确保系统内没有遗留的未固定工具或部件。
检查线缆、内插板和其他组件已正确安装。
按产品说明安装机箱盖。
激光外设或激光设备
注意事项
为避免幅射暴露和 / 或人身伤害:
•
请勿打开任何激光外设或激光设备的外壳
•
激光外设或激光设备为非用户维修设备
请与生产商联系维修事宜
Intel® Server System SR1690WB Service Guide
135
136
Intel® Server System SR1690WB Service Guide