© 2013, Moog Videolarm, Inc. All Rights Reserved
CVDC2-S25
Tubular Dust Proof Camera System
www.moogvideolarm.com
Installation and Operation Instructions for the following models:
CVDC2-S25
Tubular Dust Proof Camera System, 120Vac input,
adjustable sunshield, internal surge suppression,
128x wide dynamic range, 25x zoom, co-ax, RS-485
Before attempting to connect or operate this product, please read these instructions completely.
81-IN5498
02-13-2013
IMPORTANT SAFEGUARDS
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with damp cloth.
7
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8
9
SAFETY PRECAUTIONS
Cable Runs- All cable runs must be within permissible distance.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER ( OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SEVICING
TO QUALIFIED SERVICE PERSONNEL.
Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit.
Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit, taking into
account both the composition of the mounting surface and the weight of the unit.
10 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus ( including amplifiers) that produce heat.
11 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
12 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
13 Only use attachment/ accessories specified by the manufacturer.
14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
15 Unplug this apparatus during lighting storms or when unused for long periods of time.
16 Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled of objects have fallen into the apparatus, the
The lightning flash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of non-insulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk to persons.
Este símbolo se piensa para alertar al usuario a la presencia
del “voltaje peligroso no-aisIado” dentro del recinto de los
productos que puede ser un riesgo de choque eléctrico.
Ce symbole est prévu pour alerter I’utilisateur à la presence
“de la tension dangereuse” non-isolée dans la clôture de
produits qui peut être un risque de choc électrique.
Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.
Este símbolo é pretendido alertar o usuário à presença “di
tensão perigosa non-isolada” dentro do cerco dos produtos
que pode ser um risco de choque elétrico.
Questo simbolo è inteso per avvertire I’utente alla presenza
“di tensione pericolosa” non-isolata all’interno della
recinzione dei prodotti che può essere un rischio di scossa
elettrica.
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Be sure to periodically examine the unit and the supporting structure to make sure that the integrity
of the installation is intact. Failure to comply with the foregoing could result in the unit separating
from the support structure and falling, with resultant damages or injury to anyone or anything struck
by the falling unit.
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material.
They are the safest material in which to make future
shipments of the equipment.
2 These Installation and Operating Instructions.
SERVICE
If technical support or service is needed, contact us at
the following number:
TECHNICAL SUPPORT
AVAILABLE 24 HOURS
1 - 800 - 554 -1124
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones importantes
en la literatura que acompaña la aplicación.
Ce symbole de point d’exclamation est prévu pour alerter
l’utilisateur à la presence des instructions importantes dans
la littérature accompagnant l’appareil.
Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der Literatur
alarmieren, die das Gerät begleitet.
Este símbolo do ponto do exclamation é pretendido alertar o
usuário à presença de instruções importantes na literatura
que acompanha o dispositivo.
Questo simbolo del punto del exclamaton è inteso per
avvertire l’utente alla presenza delle istruzioni importanti nella
letteratura che accompagna l'apparecchio.
Limited Warranty for Moog Videolarm Products
Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:
PRODUCT CATEGORY
PARTS \ LABOR
All Enclosures and Electronics*
Five
Poles/PolEvators™/CamEvator
Three (3) Years
Warrior Series™/Q-View™/IR Illuminators
Five
(5) Years
SView Series™
Five
(5) Years **6 months if used in auto scan/tour operation
Controllers
Five
(5) Years
Power Supplies
Five
(5) Years
EcoKit
Three (3) Years
Accessory Brackets
Five
Liberty Dome
Three (3) Years
*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™
Three (3) Years **6 months if used in auto scan/tour operation
(5) Years
(5) Years
During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm
Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with
a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support
Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to
provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or
parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions.
TERMS AND CONDITIONS
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an
explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.
If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of
investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period
of the entire Product. The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that
part or the remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any
Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the
warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,
earthquakes), modification, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the
Product. Furthermore, Moog Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts
(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-qualified personnel; operation of the Product outside of the
published environmental and electrical parameters, or if such Product’s original identification (trademark, serial number) markings have been defaced, altered,
or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not
been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”
(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any
cost associated with removal of defective product and installation of replacement product is not included in this warranty.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR
ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL
CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT
THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS
PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.
LIMITATION OF LIABILITY
THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL
PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,
REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
GENERAL INSTRUCTIONS:
!
Use only with Class 2 Power Supply
HARDWARE KIT
3
2
1
1
1
1
1
2
1
1
1
1
1
2
Cable Tie
BHCS, 1⁄4-20 x 1⁄4-inch
BHCS, 1⁄4-20 x 5⁄8-inch
BHCS, 1⁄4-20 x 3⁄4-inch
BHCS, 1⁄4-20 x 1⁄2-inch
BHCS, 1⁄4-20 x 3⁄8-inch
BHCS, 1⁄4-20 x 11⁄4-inch
0.4 mm (0.016-inch) Plastic Spacer
1.65 mm (0.065-inch) Plastic Spacer
3.9 mm (0.154-inch) Plastic Spacer
7.4 mm (0.292-inch) Plastic Spacer
9.8 mm (0.385-inch) Plastic Spacer
3⁄8-inch NPT Plug
Pull Seals
RATINGS
NEMA-3R and IP54
The housing includes a “breather” hole in the front end cap. The “breather” hole
prevents the accumulation of moisture inside the housing when installed in areas of
high humidity. With the “breather” hole open, the housing meets the enclosure rating
requirements of NEMA-3R and IP54.
3. Remove the cradle assembly by pushing gently on the metal part of front cap
and simultaneously grasping the rear handle and pulling the cradle assembly out of
the housing. Be sure to keep the edges of the end caps clean and free of scratches
(Figure 2).
Retention Screw
Figure 2
4. The camera is pre-installed into the cradle assembly. Refer to instuction
81-IN5494 (Included) for camera manual (Figure 3).
NEMA-6P and IP68
For installations requiring an enclosure rating of NEMA-6P or IP68, the breather
hole must be plugged using the pull seal (Part No. 315 2569 001) provided in the
hardware kit. Refer to Final Assembly under INSTALLATION for proper installation.
ATTENTION: Installation should be performed by quallified service personnel only in
accordance with the National Electrical Code or applicable local codes.
CAMERA INSTALLATION
TOOLS REQUIRED
Phillips head screwdriver
5⁄32-inch (or 4 mm) hex wrench
5⁄16-inch (or 8 mm) hex wrench
1. Remove the cradle from the housing by lowering the retaining screw completely on
the bottom rear of the housing.
2. Turn slot on the retaining ring, located on the rear cap, to the bottom of the housing
(Figure 1).
Figure 1
Spacers
Figure 3
1/4-20 Screws
LIQUID TIGHT FITTINGS:
1. The dual male threaded portion of the three liquid tight fittings, two NPT 1⁄2-inch,
and one NPT 3⁄8-inch, located in the rear of the cradle, are provided preinstalled.
Do not remove or loosen these parts. They have been installed to a specified torque
to prevent entrance of water. The two large fittings are supplied with seal glands for
cables with diameters from 4.3 mm (0.17-inch) to 11.9 mm (0.47-inch). The small
fitting will accept cables with diameters from 4.6 mm (0.181-inch) to 7.9 mm
(0.312-inch) (Figure 4).
Black - focus
Seal Cap
Red - common
Green - zoom
Seal Gland
Figure 4
!
!
Dual Male Portion
CAUTION: Be sure to securely tighten all fittings to ensure a liquidtight seal. Failure to do so could allow water to enter the housing and
damage the camera and lens. If a sealant is to be used, be sure it is a
neutral cure type. Sealants that release acetic acid may harm camera
electronics.
NOTE: Use of drip loops is recommended on the wiring outside of the
rear end cap.
2. If no lens control or feed-through wiring will be used, remove the preinstalled 3⁄8inch liquid-tight fitting from the small bottom center hole and install the 3⁄8-inch NPT
plug provided. Use a 5⁄16-inch (or 8 mm) hex wrench to tighten. Failure to do so will
allow water to enter and cause damage to all electronic parts (Figure 5).
Figure 5
black - line
white - neutral
green - ground
NOTE: (must be connected to
ground for surge protection).
3/8-inch NPT Plug
Wiring Diagram
!
CAUTION: Be sure to securely tighten all fittings to ensure a liquid
tight seal. Failure to do so could allow water to enter the housing and
damage the camera and lens.
FINAL ASSEMBLY
!
5. Reinsert the cradle assembly. Turn the slot on the retaining ring to the top of the rear
cap (Figure 10).
CAUTION: If the breather hole is open, do NOT mount the housing in a
position where the front end cap is pointed upward.
1. To maintain enclosure protection ratings of NEMA-6P and IP68, the pull seal
(provided in the hardware kit) must be installed in the front end cap. It is recommended
that the pull seal be installed in a cool, dry environment to prevent trapping moisture
inside the housing (Figure 6).
NOTE: Pull seal installation allows the housing’s front end cap to be pointed upward.
Front Face
Figure 10
6. Position the housing vertically and replace the cradle assembly by applying pressure
onto the rear cap until the retaining ring stops against the housing. (see Figure 11).
Breather Hole
Figure 6
TO INSTALL THE PULL SEAL:
1. Remove the cradle assembly from the housing.
2. Obtain a rubber pull seal from the hardware kit (Part Number 3152569 001).
An extra pull seal is also provided (Figure 7).
Head
Long End
Figure 7
3. Insert the long end of the pull seal into the breather hole starting from the front side
of the endcap (Figure 8).
Cradle
Front of
Endcap
Figure 11
!
CAUTION: If a pull seal is installed in the breather hole, be careful not to
pinch the head of the pull seal. Damage to the pull seal may allow water
to enter the housing, causing damage to the c camera and lens.
Pull Seal
Breather Hole
Figure 8
4. Grip the pull seal’s long end from the back of the front endcap. Steadily pull the
long end until the head of the pull seal is flat against the front of the endcap
(Figure 9).
NOTE: The Pull Seal’s long end will stretch when pulled through the breather hole.
Front Endcap
Grip and Pull
Figure 9
Rear Face of Head Should
Be Flush with Front Face
of Front Endcap
7. Tighten the retention screw, making sure it is seated into the rear cap groove.
8. Attach the housing to the appropriate mount or pan/tilt using the instructions
provided. According to the orientation of the housing,the cradle assembly may need to
be rotated. To rotate the cradle assembly (while mounted), grasp the rear handle and
rotate to the desired position. View the monitor while rotating.
SUNSHIELD INSTALLATION:
1. Slide the sunshield onto the housing from the rear (shown) or the front of the housing.
2. Position the slot in the sunshield over the housing mounting holes.
3. Secure the sunshield by passing the housing mounting screws (not provided) through the sunshield slot and tightening them.
4. The sunshield can be adjusted forward and back for more or less overhang.
Sunshield
Sunshield
Front of
Housing
Sunshield
Sunshield
Housing
Mounting
Holes
Sunshield Slot
Housing
Product Registration/Warranty
Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest
quality products available and superior customer service.
Should a problem arise, rest assured that Moog Videolarm stands behind its products by offering impressive 3 Year and 5 Year warranties, depending on the product
purchased. See full warranty details at www.moogvideolarm.com/technical-support/warranty-plan/
Register Your Products Online
Please take a few moments to register your purchase via the Online Product Registration Form at:
www.moogvideolarm.com/technical-support/product-registration
Register your recent Moog Videolarm purchase and benefit from the following:
• Simple and Trouble-Free RMA process
• Receive product updates, and special promotion
• Eliminate the need to archive original purchase documents:
Receipts, Purchase Orders, etc…