Preliminary Installation/Operation for Frontload Washers, CE

www.groupdynamics-laundry.com
sales@groupdynamics.lv
FLW1527C
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 803623ENR1
January 2013
Installation/Operation
Frontload Washers
www.groupdynamics-laundry.com
sales@groupdynamics.lv
www.groupdynamics-laundry.com
sales@groupdynamics.lv
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property
damage.
W030
NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense, caution, and
carefulness are factors which cannot be built into these washers. These factors MUST BE supplied by the
person(s) installing, maintaining, or operating the washer.
Always contact the distributor, service agent, or the manufacturer about any problems or conditions you do not
understand.
Read all instructions before using washer.
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
1
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Table of
Contents
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
3
3
3
Installation...........................................................................................
Dimensions and Specifications.............................................................
Before You Start ...................................................................................
Tools ................................................................................................
Central Pay Models..........................................................................
Installing the Washer ............................................................................
Step 1: Position Washer Near Installation Area ..............................
Step 2: Position and Level the Washer ............................................
Step 3: Connect Fill Hoses...............................................................
Step 4: (Non-Gravity Drain Models Only) Connect Drain Hose
to Drain Receptacle ........................................................................
Step 5: (Gravity Drain Models Only) Connect Drain Outlet
to Drain System ..............................................................................
Step 6: Remove the Shock Sleeves and Shipping Brace .................
Step 7: Wipe Out Inside of Wash Drum ..........................................
Step 8: Install Appropriate Electrical Plug ......................................
Step 9: Connect the Washer to Electrical Power .............................
Step 10: Check Installation ..............................................................
5
5
7
7
7
8
8
8
9
12
13
13
14
17
19
Operation.............................................................................................
Operation Instructions ..........................................................................
Step 1: Load Laundry.......................................................................
Step 2: Close Loading Door.............................................................
Step 3: Add Laundry Supplies .........................................................
Step 4: Set Fabric Selector/Wash Temperature (°C) .......................
Step 5: Set Soil Level.......................................................................
Step 6: Insert Coin(s) or Card, if Necessary ....................................
Step 7: Press Start ............................................................................
20
20
20
20
21
21
21
22
22
Maintenance ........................................................................................
User-Maintenance Instructions.............................................................
Lubrication .......................................................................................
Cold Weather Care...........................................................................
Care of Your Washer .......................................................................
Cleaning Glass Sealing Area ...........................................................
Replacing Hoses...............................................................................
Vacations and Non-Use ...................................................................
Reinstallation of Shipping Materials ...............................................
Cleaning Foreign Object Trap .........................................................
23
23
23
23
23
23
23
23
24
24
11
Troubleshooting .................................................................................. 25
Disposal of Unit ................................................................................... 27
Contact Information........................................................................... 28
Installer Checklist................................................................. Back Cover
© Published by permission of the copyright owner.
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
2
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Throughout this manual and on machine decals, you
will find precautionary statements (“DANGER,”
“WARNING,” and “CAUTION”) followed by specific
instructions. These precautions are intended for the
personal safety of the operator, user, servicer, and
those maintaining the machine.
(Save These Instructions)
DANGER
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
WARNING
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
CAUTION
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
1. Read all instructions before using the washer.
2. Refer to the EARTHING INSTRUCTIONS in
the INSTALLATION manual for the proper
earthing of the washer.
3. Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, or other
flammable or explosive substances as they give
off vapors that could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
the use of the appliance by a person responsible
for their safety.
8. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
3
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Safety Information
9. Do not reach into the washer if the wash drum is
moving.
10. Do not install or store the washer where it will be
exposed to water and/or weather.
11. Do not tamper with the controls.
12. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out.
13. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
14. Use your washer only for its intended purpose,
washing clothes.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
earthing must comply with local codes and be
made by licensed personnel when required. Do
not do it yourself unless you know how!
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
24. Always follow the fabric care instructions
supplied by the garment manufacturer.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
17. To reduce the risk of fire, clothes which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc. or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
19. Keep your washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have your washer checked by a
qualified service person.
20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
4
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Dimensions and Specifications
The workstation average sound pressure level is
68.7 dBA.
51 mm (2 in.)
38 mm
(1.5 in.)
938 mm (36.94 in.)
683 mm (26.875 in.)
711 mm (28 in.)
51 mm (2 in.)
371 mm
(14.6 in.)
333 mm
(13.1 in.)
751 mm (29.6 in.)
790 mm (31.1 in.)
610 mm
(24 in.)
FLW2253N
1092 mm (43 in.) Painted Models
1073 mm (42.25 in.) Stainless Steel Models
COIN/CARD MODELS EQUIPPED WITH DRAIN HOSE
FLW2253N
711 mm (28 in.)
51 mm (2 in.)
38 mm
(1.5 in.)
371 mm
(14.6 in.)
938 mm (36.94 in.)
333 mm
(13.1 in.)
751 mm (29.6 in.)
790 mm (31.1 in.)
610 mm
(24 in.)
683 mm (26.875 in.)
1051 mm (41.375 in.) Painted Models
1035 mm (40.75 in.) Stainless Steel Models
FLW2254N
CENTRAL PAY MODELS EQUIPPED WITH DRAIN HOSE
FLW2254N
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
5
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
51 mm (2 in.)
711 mm (28 in.)
38 mm
(1.5 in.)
1092 mm (43. in.)
Painted Models
1073 mm (42.25 in.)
Stainless Models
104.1 mm
(4.1 in.)
938 mm (36.94 in.)
106.7 mm
(4.2 in.)
371 mm
(14.6 in.)
333 mm
(13.1 in.)
751 mm (29.6 in.)
790 mm (31.1 in.)
610 mm
(24 in.)
1
FLW2255
683 mm (26.875 in.)
COIN/CARD MODELS WITH GRAVITY DRAIN
FLW2255N
1
38.1 mm (1.5 in.) Inside Diameter
47.2 mm (1.86 in.) Outside Diameter
711 mm (28 in.)
38 mm
(1.5 in.)
1051 mm (41.375 in.)
Painted Models
1035 mm (40.75 in.)
Stainless Models
104.1 mm
(4.1 in.)
938 mm (36.94 in.)
106.7 mm
(4.2 in.)
371 mm
(14.6 in.)
333 mm
(13.1 in.)
751 mm (29.6 in.)
790 mm (31.1 in.)
610 mm
(24 in.)
1
FLW2256
683 mm (26.875 in.)
CENTRAL PAY MODELS WITH GRAVITY DRAIN
FLW2256N
1
6
38.1 mm (1.5 in.) Inside Diameter
47.2 mm (1.86 in.) Outside Diameter
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Before You Start
NOTE: A 20.32 cm (8 in.) coin drawer is required
for coin operated models.
Tools
For most installations, the basic tools you will need
are:
1
2
3
4
NOTE: If the washer is delivered on a cold day
(below freezing), or is stored in an unheated room
or area during the cold months, do not attempt to
operate it until the washer has had a chance to
warm up.
NOTE: Install dryer before washer. This allows
room for attaching exhaust duct.
NOTE: Some moisture in the wash drum is normal.
Water is used during testing at the manufacturer.
Central Pay Models
5
D074I
1
2
3
4
5
Wrench
Screwdriver
Pliers
Socket Wrench
Level
The machine is shipped from the factory with the
Electronic Control Diagnostic Harness Assembly
unplugged. To avoid unauthorized manual
programming or vending perform the following steps.
1. Open service door. Refer to Figure 2.
2. Locate diagnostic harness on electronic control.
3. Plug connectors for “white/black” wire and “red/
blue” wire together.
Figure 1
1
DRY2074N
1
Service Door
Figure 2
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
7
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Installing the Washer
Step 2: Position and Level the Washer
Step 1: Position Washer Near Installation
Area
Move washer so that it is within 1.2 meters (4 feet) of
the desired area of installation.
NOTE: For best performance and to minimize
vibration or movement, install washer on a solid,
sturdy and level floor. Some floors may need to be
reinforced, especially on a second floor or over a
basement. Do not install the washer on carpeting,
soft tile, a platform or other weakly supported
structures.
WARNING
Washers elevated above floor level must
be anchored to that elevated surface,
base or platform. The material used to
elevate the washer should also be
anchored to the floor to ensure that the
washer will not walk or that the washer
can not be physically pulled, tipped or
slid from its installed position. Failure to
do so may result in conditions which can
produce serious injury, death and/or
property damage.
W306
Position washer so it has sufficient clearance for
installation and servicing.
NOTE: Use of the dispenser drawer or washer door
as a handle in the transportation of the washer may
cause damage to the dispenser or door.
Place washer in position on a solid, sturdy and level
floor. Installing the washer on any type of carpeting,
soft tile, a platform or other weakly supported
structures is not recommended.
Place a level on the raised portion of cabinet top and
check if the washer is level from side to side and front
to back.
If washer is not level, tilt washer to access the front
and rear leveling legs. For easier access to leveling
legs, prop up washer with a wooden block. Refer to
Figure 4. Loosen locknut and adjust legs until the
washer is level from side to side and front to back
(using a level). Washer should not rock.
H054I
Tighten the locknuts securely against the washer
base using the wrench. If the locknuts are not tight,
washer will move out of position during operation.
H054I
Figure 3
8
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
NOTE: DO NOT slide washer across floor if the
leveling legs have been extended, as legs and base
could become damaged.
Remove rubber feet from accessories bag and place on
all four leveling legs.
Verify that unit doesn’t rock.
3
2
1
Step 3: Connect Fill Hoses
WARNING
Under certain conditions, hydrogen gas
may be produced in a hot water system
that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If
the hot water system has not been used
for such a period and before using the
washer, turn on all hot water faucets and
let the water flow from each for several
minutes. This will release any
accumulated hydrogen gas. The gas is
flammable. Do not smoke or use an open
flame during this time.
W029
Water Supply
6
5
4
FLW2134N
FLW2134N
1
2
3
4
5
6
Leveling Leg
Washer Base
Level
Wood Block
Locknut
Rubber Foot
Figure 4
Water supply faucets must fit standard 19.1 mm
(3/4 inch) female garden hose couplings. DO NOT
USE SLIP-ON OR CLAMP-ON CONNECTIONS.
Recommended cold water temperature is 16° to
27° Celsius (60° to 80° Fahrenheit). Recommended
maximum hot water temperature is 51° Celsius
(125° Fahrenheit).
WARNING
To prevent personal injury, avoid contact
with inlet water temperatures higher than
51° Celsius (125° Fahrenheit) and hot
surfaces.
W750
Models NF3LLFSG401UT06,
NF3LLFSG402UT06, NF3LLFSP401UT06,
NF3LLFSP402UT06 and NF3LXFSP402UW06:
Water pressure must be a minimum of 138 to a
maximum of 689 kPa (20 to 100 psi) static pressure
measured at the faucet.
All other models: Water pressure must be a minimum
of 138 to a maximum of 827 kPa (20 to 120 psi) static
pressure measured at the faucet.
NOTE: Water pressure under 138 kPa (20 psi) will
cause an extended fill time in the washer and may
not properly flush out the detergent dispenser.
The appliance is to be connected to the water mains
using new hose-sets and the old hose-sets should not
be reused.
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
9
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Turn on the water supply faucets and flush the lines for
approximately two minutes to remove any foreign
materials that could clog the screens in the water
mixing valve.
1
COLD
HOT
Connecting Hoses
Models NF3LLFSG401UT06,
NF3LLFSG402UT06, NF3LLFSP401UT06,
NF3LLFSP402UT06 and NF3LXFSP402UW06: To
comply with water regulations, this washing machine
must be fitted with an approved 3/4 inch single check
valve to both the hot and cold supplies between shut
off valve and fill hose. Refer to Figure 5. Maximum
water flow rate to the dispenser is 10 liters per minute.
Screw BLACK colored hose couplings with filter
screens onto water supply faucets and brass hose
couplings with rubber washers to water mixing valve
finger-tight and then approximately 1/4 turn with
pliers.
IMPORTANT: DO NOT cross thread or
overtighten couplings. This will cause them to leak.
Turn water on and check for leaks. If leaks are found,
retighten the hose couplings. Continue tightening and
rechecking until no leaks are found.
7
2
3
4
6
5
FLW2216N
1
2
3
4
5
6
7
Faucet
Fill Hoses
Install this End of Hose to Valve Connections
at Rear of Washer
Plain Rubber Washer (in accessory bag)
Install this End of Hose to Water Supply
Faucet (Black Colored Coupling for Metric)
Filter Screens (in accessory bag – screen
must face outward)
Check Valves (use on models
NF3LLFSG401UT06, NF3LLFSG402UT06,
NF3LLFSP401UT06, NF3LLFSP402UT06
and NF3LXFSP402UW06)
Figure 5
IMPORTANT: All hoses should be checked on a
monthly basis for any visible signs of deterioration.
Any hose showing signs of deterioration should be
replaced immediately. All hoses should be replaced
every five years.
10
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
2
1
Installation
Step 4: (Non-Gravity Drain Models Only)
Connect Drain Hose to Drain Receptacle
3
Remove the drain hose from its shipping position on
the rear of the washer by removing the shipping tape.
IMPORTANT: Drain receptacle must be capable of
handling a minimum of 35 mm (1-3/8 inch) outside
diameter drain hose.
WATER
MIXING
VALVE
4
1
FLW1942N
FLW1942N
1
2
3
4
Water Supply Faucets
Hot Water Connection
Cold Water Connection
Fill Hoses
Figure 6
FLW1953N
1
Shipping Tape
Figure 7
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
11
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Standpipe Installation
Step 5: (Gravity Drain Models Only)
Connect Drain Outlet to Drain System
Place the drain hose into the standpipe.
Remove drain fitting (four inches long) and hose
clamp from accessories bag. Insert drain fitting into
drain outlet hose. Clamp hose and fitting.
Connect the drain fitting to a vented drain system
using a flexible connection (obtain locally). Inside
diameter of fitting is 38.9 mm (1.53 in.) and outside
diameter is 42.2 mm (1.66 in.). The drain system must
be vented to prevent an air lock or siphoning.
610 to 914.4 mm
(24 to 36 in.)
RECOMMENDED
HEIGHT
2
IMPORTANT: Increasing the drain hose length,
installing elbows, or causing bends will decrease
drain flow rates and increase drain times,
impairing machine performance.
1
FLW1943N
FLW1943N
1
2
Standpipe 50.8 mm (2 in.) or 40 mm
(1-1/2 in.)
Beaded strap from accessory bag
Figure 8
2
1
FLW2091N
FLW2091N
1
2
Drain Trough
Drain Outlet Hose
Figure 9
12
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Step 6: Remove the Shock Sleeves and
Shipping Brace
Remove front access panel by removing the two screws
at the bottom of the panel.
Remove the five bolts and lockwashers from shipping
brace with 14.3 mm (9/16 in.) wrench and remove
brace. Refer to Figure 10. One is holding the brace to
the weight. Remove this bolt first. Four bolts are
located on the washer base. Remove the two front
bolts next and then the two rear bolts. Remove all four
shock sleeves by pulling on the yellow rope. Remove
label from front side of front access panel and place on
backside of front access panel or shipping brace for
future reference.
Step 7: Wipe Out Inside of Wash Drum
IMPORTANT: Prior to first wash, use an
all-purpose cleaner, or a detergent and water
solution, and a damp cloth to remove shipping dust
from inside wash drum.
NOTE: The shipping brace, bolts, washers and
shock sleeves should be saved and MUST be
reinstalled whenever the washer is moved more
than 1.2 m (4 ft.). Refer to Maintenance section for
instructions. Do not lift or transport washer from
front or without shipping materials installed.
FLW2135N
Reinstall front access panel.
FLW2135N
IMPORTANT: DO NOT tip washer more than
152.4 mm (6 in.) in any direction after shipping
brace has been removed. Shock absorbers may
separate and damage to washer may result. For
leveling purposes, the washer may be tilted a
maximum of 152.4 mm (6 in.) in any direction.
Figure 11
1
2
3
4
FLW2124N
FLW2124N
1
2
3
4
Shock Sleeves
Motor Mount
Hooked End of Shipping Brace
Bolts and Lockwashers
Figure 10
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
13
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Step 8: Install Appropriate Electrical Plug
1
400 Volt, 50 Hertz, 9.8 Amp
2
3
4
5
6
7
NOTE: This washer is factory-wired for a 400 Volt
electrical supply.
Have a qualified electrician install appropriate
electrical receptacle.
To attach customer-supplied power cord
(400 Volt WYE):
1. Remove electrical access panel on rear of
machine.
2. Remove plastic plug from hole in rear of
machine.
L 1 L 2 L 3
3. Install strain relief, supplied with machine, in
hole.
4. Put power cord through hole. Refer to Figure 12.
N
400
Volt
230
Volt
400
Volt
8
400
Volt
1
230
Volt
230
Volt
TERMINAL BLOCK WIRED FOR 400 VOLT WYE
AS VIEWED THROUGH REAR ACCESS PANEL
FLW1915N
NOTE: 1.5 mm2 wire required for 3 phase, 4 wire
connection.
1
Black Wire
2
Black/White Wire
3
Black/Red Wire
4
White Wire
5
White/Red Wire
6
White/Black Wire
7
Green/Yellow Wire
8
Earth – Power Cord
FLW1953N
1
Figure 13
Install power cord through this hole after
removing plastic plug. Use strain relief
supplied in accessories bag.
Figure 12
5. Attach power cord wires as shown in Figure 13.
6. Tighten down the strain relief (supplied with
unit) on the power cord.
7. Reinstall access panel.
14
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
To convert from 400 Volt WYE to 230 Volt 3 wire
plus earth, 15 AMP DELTA. Refer to Figures 13
and 14:
1 2
3
4
5
6
1. Remove electrical access panel on rear of
machine.
2. Remove plastic plug from hole in rear of
machine.
3. Install strain relief, supplied with machine, in
hole.
4. Put power cord through hole. Refer to Figure 12.
5. On terminal block quick-disconnect terminals,
remove white/black wire from neutral and attach
to terminal L1.
6. Move white/red wire from neutral to L2.
7. Move white wire from neutral to L3.
8. Place one 506113 Sticker, supplied with washer,
near each of the two serial plates. Mark correct
voltage on sticker.
9. Place 801292 Label, supplied with washer,
underneath terminal block. Refer to Figure 14.
10. Attach power cord wires as shown in Figure 14.
7
L 1 L 2 L 3
8
230
Volt
230
Volt
230
Volt
FLW1916N
TERMINAL BLOCK WIRED FOR 230 VOLT
DELTA
AS VIEWED THROUGH REAR ACCESS PANEL
11. Replace access panel.
FLW1916N
NOTE: 1.5 mm2 wire required for 3 phase, 4 wire
connection.
1
Black Wire
2
White/Black Wire
3
Black/White Wire
4
White/Red Wire
5
Black/Red Wire
6
White Wire
7
Earth – Power Cord
8
Neutral
Figure 14
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
15
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
To convert from 400 Volt WYE to 230 Volt 2 wire
plus earth, 30 AMP Single-Phase. Refer to Figures
13 and 15:
1 2
3
4
L 1
N
5
6
1. Remove electrical access panel on rear of
machine.
2. Remove plastic plug from hole in rear of
machine.
3. Install strain relief, supplied with machine, in
hole.
4. Put power cord through hole. Refer to Figure 12.
5. On terminal block quick-disconnect terminals,
remove black/white wire from L2 and attach to
terminal L1.
6. Move black/red wire from L3 to L1.
7. Place one 506113 Sticker, supplied with washer,
near each of the two serial plates. Mark correct
voltage on sticker.
8. Place 801813 Label, supplied with washer,
underneath terminal block. Refer to Figure 15.
9. Attach power cord wires as shown in Figure 15.
10. Replace access panel.
7
8
230
Volt
TERMINAL BLOCK WIRED FOR 230 VOLT
FLW2030N
SINGLE-PHASE AS VIEWED THROUGH
REAR
ACCESS PANEL
FLW2030N
1
2
3
4
5
6
7
8
Black Wire
Black/White Wire
Black/Red Wire
White/Black Wire
White/Red Wire
White Wire
Earth – Power Cord
Neutral
Figure 15
16
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Step 9: Connect the Washer to Electrical
Power
Electrical Requirements
400 Volt, 50 Hertz, 9.8 Amp
NOTE: This washer is factory-wired for a 400 Volt
electrical supply.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
earthing MUST abide with local electrical
codes. It is the customer’s responsibility
to have the wiring and fuses checked by a
qualified electrician to make sure the
laundry room has adequate electrical
power to operate the washer.
FLW2257N
FLW2257N
Figure 16
W246
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
17
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
FLW2145N
POWER CORD
FLW2146N
HARDWIRE
FLW2145N
FLW2146N
NOTE: Electrical receptacle must be located so that it is easily accessible with machine in place. If machine is hard
wired, an intermediate shut-off box with a 3 mm gap is required to meet EN 60335-1, clauses 24.3 and 22.2 or 3.5 mm
gap is required to meet Standard IEC 60335-1, clauses 24.3 and 22.2. Gap is defined as the minimum contact
separation of each pole in the switch between the “ON” and “OFF” positions.
Figure 17
Earthing Instructions
The washer must be earthed. The washer must be
properly earthed in accordance with all local codes and
ordinances.
WARNING
Improper connection of the equipmentearthing conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the washer is
properly earthed.
W032
18
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installation
Connecting to Central Pay System
1
IMPORTANT: Any central pay device and related
installation wiring that is connected to the washer
must maintain the Electromagnetic Compatibility
(EMC) of the washer in order to comply with the
appropriate national EMC regulatory
requirements. The central pay device and related
wiring, as a minimum, must meet the emission
requirements of EN55014-1 and the immunity
requirements of EN55014-2.
Start Pulse Input Wiring Connections
Use 511478 Remote Vend Wire Harness, supplied in
accessories bag, to connect input to control
(pin 1 – black; pin 2 – red).
The start pulse is an open collector input to the control.
The start pulse input is active when the input of the
H11L1 optocoupler is energized. The start pulse is
considered valid if it is at least 15 msec. in length with
a maximum length of 1 sec. The minimum time
between start pulses is 25 msec. The minimum active
input current for a start pulse is 3 mA and the
maximum active input current is 30 mA. Refer to
wiring diagram for connections to control.
FLW2031N
1
Run wiring from central pay system through
here.
Figure 18
Available Output Wiring Connections
Step 10: Check Installation
Use 511478 Remote Vend Wire Harness, supplied in
accessories bag, to connect output to control
(pin 3 – white/red; pin 4 – orange/black).
Refer to Installer Checklist on the back cover of this
manual and make sure that washer is installed
correctly.
The available output is opto-isolated with an open
collector device (4N25) that provides a signal to an
external vending device such as a central pay system.
When active it indicates that the washer is not
currently in use and is available to use. The available
output is limited to 5 mA maximum at 28 VDC
maximum. Refer to wiring diagram for connections to
control.
Run washer through one complete cycle to make sure
it is operating properly.
NOTE: Wiring to the central pay system should
exit machine through hole in rear of control
cabinet. Refer to Figure 18.
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
19
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Operation
Operation Instructions
Step 2: Close Loading Door
Step 1: Load Laundry
Load items loosely into wash drum. (8.1 kg
[18 pounds] maximum dry clothes load)
NOTE: Small items may get caught around the
door. Place these articles inside a mesh garment
bag.
FLW2233N
Figure 20
FLW2232N
Figure 19
When washing bulky items such as blankets and
comforters, use the DELICATES 30 or DELICATES
COLD cycle.
20
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Operation
Step 3: Add Laundry Supplies
Open dispenser drawer. Measure and add low sudsing,
high efficiency (HE) detergent (1), bleach (2) and
fabric softener (3) to the dispenser drawer (refer to
Figure 21). Close dispenser drawer.
Step 4: Set Fabric Selector/Wash
Temperature (°C)
Push touchpad for desired cycle. Light indicates
selection.
IMPORTANT: If using a non-HE detergent, avoid
oversudsing by using 1/2 of the detergent
manufacturer’s recommended amount.
NORMAL 90
FLW21R
3
2
NORMAL 60
FLW22R
1
NORMAL 40
FLW23R
PERM PRESS 60
FLW24R
FLW2234N
DELICATES 30
FLW2234N
1
2
3
FLW25R
Detergent
Bleach
Fabric Softener
DELICATES COLD
(temperature of water from tap)
FLW26R
Figure 21
CAUTION
NOTE: Changes can be made to Fabric Selector
setting up until the first fill is complete.
Dispenser drawer requires a special tool
for removal. Contact a service person if
removal is necessary.
W236
Step 5: Set Soil Level
Push Soil Level touchpad to select A, B or C. Light
indicates selection.
.
SOIL LEVEL
FLW27R
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
21
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Operation
Step 6: Insert Coin(s) or Card, if
Necessary
Indicator Lights
INSERT COINS/CARD
When INSERT COINS/CARD is lit, the digits show the
vend price remaining to be satisfied.
WASH, RINSE, SPIN
These are lit during the appropriate portions of the
cycle.
DOOR
DOOR is lit whenever the door is locked. The door
cannot be opened when this light is on.
W388I
A, B, C
These are lit to indicate the soil level selected.
Figure 22
START
START flashes one second on and one second off when
the full vend price has been satisfied.
NOTE: Once a cycle has started, the door can only
be opened by first disconnecting power and waiting
one minute.
WARNING
DRY1936N
To reduce the risk of bodily injury, do not
remove laundry from washer until all
lights are out, and all moving parts have
stopped.
W092
Figure 23
Step 7: Press Start
After vend price has been satisfied, push the START
pad.
FLW2235N
Figure 24
22
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Maintenance
User-Maintenance Instructions
Replacing Hoses
Lubrication
All hoses should be checked on a monthly basis for
any visible signs of deterioration. Any hose showing
signs of deterioration should be replaced immediately.
All hoses should be replaced every five years.
All moving parts are sealed in a permanent supply of
lubricant or are equipped with oilless bearings.
Additional lubrication will not be necessary.
Do not lubricate the door hinge. If the hinge makes
noise, replace the hinge.
Cold Weather Care
If the washer is stored in an unheated room or area
during the cold months, do not attempt to operate it
until the washer has had a chance to warm up. Water
from the previous cycle may remain.
Vacations and Non-Use
IMPORTANT: Turn off the water supply to the
washer whenever there will be a period of non-use.
Leave the loading door open during periods of non-use
to allow the wash drum to dry out and avoid a musty
smell.
Care of Your Washer
Use only a damp or sudsy cloth for cleaning the
control panel. Some cleaning product sprays may
harm the finish on the control panel or damage the
interior.
Wipe the washer cabinet as needed. If detergent,
bleach or other washing products are spilled on the
cabinet, wipe immediately. Some products will cause
permanent damage if spilled on the cabinet.
Do not use scouring pads or abrasive cleansers.
The wash drum will need no particular care although it
may need rinsing or wiping after an unusual load has
been washed.
The outside of the door window can be cleaned with
household window cleaner.
Running an occasional rinse cycle with bleach will
help to avoid a musty smell in the wash drum.
Cleaning Glass Sealing Area
In order to assure that the door properly seals against
water leaks, the following surfaces should be wiped
off periodically:
•
The outside perimeter of the door glass where the
seal contacts the glass
•
The front surface of the door seal lip
Usually a mild soap solution will work. If there is an
extreme build-up of minerals from a hard water
supply, the surfaces may need to be cleaned with a
lime removal chemical.
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
23
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Maintenance
Reinstallation of Shipping Materials
Cleaning Foreign Object Trap
To prevent damage while moving the washer, the
shipping materials MUST be reinstalled.
The washer’s pump has a trap that may collect foreign
objects. The trap may need to be cleaned if water is
draining slower than usual. To clean:
•
Disconnect washer from electrical supply.
•
While supporting the front access panel, remove
two screws from the bottom edge of the panel.
•
Gently lower the panel to remove it from the
washer.
•
Place the shock sleeves on all four shock
absorbers. Refer to Figure 25.
•
Insert hooked end of shipping brace into the open
slot of the motor mount. Refer to Figure 25.
•
Attach the brace with the five bolts and washers.
Refer to Figure 25.
•
Reinstall front access panel.
1
•
Disconnect washer from electrical supply.
•
While supporting the front access panel, remove
two screws from the bottom edge of the panel.
•
Gently lower the panel to remove it from the
washer.
NOTE: The pump may have some water in it. Use a
rag or a container to catch water. If the wash drum
is full of water, use a wet/dry shop vacuum to catch
the water.
•
With rag or vacuum ready, unscrew the cap on
the left side of the pump and remove trap.
•
Clean the debris from the trap.
•
Reinstall the trap and access panel.
•
Reconnect washer to electrical supply.
2
3
4
FLW2124N
FLW2124N
1
2
3
4
Shock Sleeves
Motor Mount
Hooked End of Shipping Brace
Bolts and Lockwashers
Figure 25
Refer to Installation section, step 6 for proper
procedures whenever the washer is moved.
24
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Troubleshooting
Try these troubleshooting tips before making a service call. They may save you time and money.
Washer Symptom
Possible Cause/Solution
Won’t Fill
•
•
•
•
•
•
•
•
Make sure power cord is plugged all the way into the electrical outlet.
Make sure hot and cold water faucets are turned on.
Make sure that the fill hoses are not kinked or twisted.
Press START keypad.
Make sure that the controls are properly set.
Make sure that the loading door is closed tightly.
Check the laundry room fuse or circuit breaker.
Clean the screens in the water mixing valve and the filter screens located at the faucet end
of the fill hoses.
Won’t Start
•
•
•
•
•
•
Make sure loading door is closed tightly.
Press START keypad.
Make sure power cord is plugged all the way into the electrical outlet.
Check the laundry room fuse or circuit breaker.
Insert coin(s) or card.
Make sure door latch is properly adjusted relative to door lock.
Won’t Spin/Tumble
•
•
•
•
•
•
•
Make sure loading door is closed tightly.
Press START keypad.
Make sure power cord is plugged all the way into the electrical outlet.
Make sure controls are properly set.
Check the laundry room fuse or circuit breaker.
Broken drive belt. Call the service person.
Foreign object trap in pump may be clogged. Clean the trap. Refer to
Maintenance section.
Stops/Pauses During
Cycle
•
•
•
Pauses are part of the washer’s normal operation.
Wash load may be unbalanced. Washer will stop and then restart spin automatically.
Check the laundry room fuse or circuit breaker.
Won’t Drain
•
•
•
•
Make sure drain hose is not kinked or twisted.
Make sure drain hose is not clogged.
Make sure drain receptacle is not clogged.
Refer to the Installation section to make sure that the drain hose has been properly
installed.
Foreign object trap in pump may be clogged. Clean the trap. Refer to Maintenance
section.
•
Water Leaks
•
•
•
•
•
•
•
Check that fill hoses are properly installed on the faucets and the washer’s water mixing
valve.
Check the condition of the fill hoses. Replace fill hoses every five years.
Check the condition of the rubber door gasket for tears or holes.
Make sure drain receptacle is not clogged.
Check building plumbing.
Laundry load may be oversudsing or overloaded. Make sure you are using low-sudsing,
high efficiency (HE) detergent and proper load sizes.
Make sure outside perimeter of the door glass where seal contacts glass is clean.
(continued)
803623 (EN)
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
25
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Troubleshooting
(continued)
Washer Symptom
Possible Cause/Solution
Too Many Soap Suds
•
•
•
Vibrates/Moves
Slightly
•
•
•
Laundry load may be oversudsing. Make sure you are using low sudsing, high efficiency
(HE) detergent.
Make sure you are using the amount of detergent recommended on the detergent’s label.
If using non-HE detergent, use only 1/2 of the detergent manufacturer’s recommended
amount.
Laundry load may be overloaded. Make sure you are using proper load sizes.
Make sure rubber feet are installed on all four leveling legs. Refer to Installation section,
Step 5.
Make sure washer is level. Uneven leveling can cause vibration.
Make sure washer is installed on a solid, sturdy and level floor. The washer should not be
installed on carpeting, soft tile, a platform or other weakly supported structures.
Is Noisy
•
•
Make sure washer is level. Uneven leveling can cause vibration.
Some sounds may be a part of normal operation for a frontload washer.
Load is too Wet
•
Wash load may be unbalanced. The washer may have limited the spin speed to prevent
damage to the machine. Redistribute the load.
Load is too small. Add items to make full load.
•
Wrong Water
Temperature
•
•
•
26
Make sure that the controls are properly set.
Check fill hoses. Make sure hot faucet hose is connected to hot mixing valve (indicated
with “H” on the valve bracket) and cold faucet is connected to cold mixing valve
(indicated with “C” on the valve bracket).
Make sure laundry room water heater is adjusted properly.
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Disposal of Unit
This appliance is marked according to the European
directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Refer to Figure 26. Instead it shall
be handed over to the applicable collection point for
the recycling of electrical and electronic equipment.
Ensuring this product is disposed of correctly will help
prevent potential negative consequences for the
environment and human health which could otherwise
be caused by inappropriate waste handling of this
product. The recycling of materials will help to
conserve natural resources. For more detailed
information about recycling of this product, please
contact the local city office, household waste disposal
service, or the source from which the product was
purchased.
803623 (EN)
MIX1N
Figure 26
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
27
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Contact Information
If service is required, contact the nearest Factory
Authorized Service Center.
If you are unable to locate an authorized service center
or are unsatisfied with the service performed on your
unit, contact the source from which you purchased
your washer.
When calling or writing about your unit, PLEASE
GIVE THE MODEL AND SERIAL NUMBERS. The
model and serial numbers are located on the
nameplate. The nameplate will be in the location
shown in Figure 27.
Date Purchased ____________________________
Model Number ____________________________
Serial Number ____________________________
Please include a copy of your bill of sale and any
service receipts you have.
WARNING
To reduce the risk of serious injury or death,
DO NOT repair or replace any part of the unit
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have
the skills to carry out.
1
W329
FLW2123N
FLW2123N
1
Nameplate
If replacement parts are required, contact the source
from where you purchased your washer.
Figure 27
28
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
803623 (EN)
www.groupdynamics-laundry.com
sales@groupdynamics.lv
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Installer Checklist
Fast Track for Installing the Washer
(Refer to the manual for more detailed information)


• Position Washer
Near Installation
Area.
• Remove the Shock
Sleeves and Shipping
Brace.
CHECK
CHECK
FLW2124N
FLW2124N
H054IE0A
H054IE0A


• Position and Level
the Washer.


• Connect Fill Hoses.
COLD
HOT
FLW2135N
FLW2135N
• Install
Appropriate
Electrical Plug.
CHECK
TLW1976N
TLW1976N
CHECK

CHECK
FLW2134N
FLW2134N
CHECK
• Wipe Out Inside of
Wash Drum.
FLW1953N
FLW1953N

(Non-Gravity Drain Models Only)
• Connect Drain Hose
to Drain Receptacle.
• Connect Washer
to Electrical
Power.
CHECK
CHECK
FLW2150N
FLW1943N
FLW1943N

(Gravity Drain Models Only)
• Connect Drain
Outlet to Drain
System.
CHECK
FLW2091N
FLW2091N
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
FLW2150N
FLW2151N
FLW2151N
Download PDF

advertising